Hotpoint RD 1076 JD UK User Manual

Displayed below is the user manual for RD 1076 JD UK by Hotpoint which is a product in the Washer Dryers category. This manual has pages.

Related Manuals

Hotpoint RD 966 JD UK Manual

Hotpoint RD 966 JD UK N Manual

Hotpoint RD 1176 JD Manual

Hotpoint RDPD 96407 JD EU Manual

Hotpoint RG 964 JD UK Manual

MSI 14 B11MOU-1076AU Manual

! This symbol reminds you to read this instruc-

tion manual.

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 6

Cutting off the water or electricity supply

Cleaning the washer-dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 7

General safety

Disposal

Description of the washer-dryer, 8-9

Control panel

Display

How to run a wash cycle or a drying cycle, 10

Wash cycles and functions, 11

Table of wash cycles

Wash functions

Detergents and laundry, 12

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Load balancing system

Troubleshooting, 13-14

Product Guarantee and Repair Information, 15

RD 1076 J

Instructions for use

WASHER-DRYER

English,1

Installation

2. If the floor is not perfectly level, compensate

for any unevenness by tightening or loosening

the adjustable front feet (see figure); the an-

gle of inclination, measured according to the

worktop, must not exceed 2°.

Levelling your appliance correctly will provide

it with stability and avoid any vibrations, noise

and shifting during operation. If it is placed on

a fitted or loose carpet, adjust the feet in such

a way as to allow enough room for ventilation

beneath the washer-dryer.

Electric and water connections

Connecting the water inlet hose

1. Connect the sup-

ply pipe by screwing

it to a cold water tap

using a 3/4 gas thre-

aded connection (see

figure).

Before performing the

connection, allow the

water to run freely un-

til it is perfectly clear.

2. Connect the other

end of the water inlet

hose to the washer-

dryer,

screwing it onto the

appliance’s cold water

inlet, situated on the

top right-hand side on

the rear of the ap-

pliance (see figure).

3. Make sure there are no kinks or bends in the

hose.

! The water pressure at the tap must be within

the values indicated in the Technical details

table (on the page 5).

! If the water inlet hose is not long enough,

contact a specialist store or an authorised

serviceman.

! Ensure that the supply taps are allowing wa-

ter through. Old taps may seize in the closed

position and thus prevent water reaching the

machine.

! Never use second-hand or old inlet hoses;

use the products supplied with the machine.

! Keep this instruction manual in a safe place

for future reference. Should the appliance be

sold, transferred or moved, make sure the

instruction manual accompanies the washer-

dryer to inform the new owner as to its opera-

tion and features.

! Read these instructions carefully: they contain

vital information on installation, use and safety.

Unpacking and levelling

Unpacking

! This is a separate

part of the polystyre-

ne base and should

be removed with the

base.

! IMPORTANT check

when unpacking

your machine.

1. Unpack the washer-

dryer.

2. Check whether

the washer-dryer has

been damaged during

transport. If this is the

case, do not install

it and contact your

retailer.

3. Remove the 4 pro-

tective screws and the rubber bush with the

respective spacer, situated on the rear of the

appliance (see also the installation leaflet).

4. Seal the gaps using the plastic plugs provided.

5. Keep all the parts: you will need them again

if the washer-dryer needs to be moved to ano-

ther location.

! Packaging materials are not children’s toys.

Levelling

Your machine may make a considerable

amount of noise if the two front feet have not

been adjusted correctly.

1. Install the washer-

dryer on a flat sturdy

floor, without resting it up

against walls, cabinets

or anything else.

Connecting the drain hose

Connect the drain

hose, without ben-

ding it, to a draining

duct or a wall drain

situated between 65

and 100 cm from the

floor;

The drain hose may

be connected to

an under-sink trap.

Before connecting

the drain hose from

the machine ensure

that any blanks or

removable ends have

been taken off the

spigot.

If it is placed over

the edge of a basin

or sink be sure the

free end of the hose

should not be under-

water.

! We advise against the use of hose extensions;

in case of absolute need, the extension must

have the same diameter as the original hose

and must not exceed 150 cm in length.

Ensure that if the drain hose is pushed into

a standpipe, that the end does not go down

more than 15cms (6 inches). If the hose is pu-

shed down too far, this may cause the machine

to self -syphon ie. continuously empty as it is

filling.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

• the socket is earthed and in compliance with

the applicable law;

• the socket is able to sustain the appliance’s

maximum power load indicated on the Tech-

nical Data Plate fixed on the machine;

• the supply voltage is included within the

values indicated on the Technical Data Plate

fixed on the machine.

• the socket is compatible with the washer-

dryer’s plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp

fused plug it can be plugged into a 13 amp

socket for immediate use. Before using the

appliance please read the instructions below.

WARNING - THIS APPLIANCE MUST BE

EARTHED.

THE FOLLOWING OPERATIONS SHOULD

BE CARRIED OUT BY A QUALIFIED ELECTRI-

CIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be

used, and the fuse cover re-fitted. If the fuse

cover is lost, the plug must not be used until a

replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be

of the correct colour as indicated by the colou-

red marking or the colour that is embossed in

words on the base of the plug. Replacements

can be obtained directly from your nearest

Service Depot.

Removing the plug:

If your appliance has a non-rewireable moul-

ded plug and you should wish to re-route the

mains cable through partitions, units etc.,

please ensure that either:

the plug is replaced by a fused 13 ampere

rewireable plug bearing the BSI mark of ap-

proval.

or:

the mains cable is wired directly into a 13

amp cable outlet, controlled by a switch, (in

compliance with BS 5733) which is accessible

without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself,

you make the pins unusable so that it cannot

be accidentally inserted into a socket.

Instructions for connecting cable to an alternati-

ve plug:

Important: the wires in the mains lead are co-

loured in accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

65 - 100 cm

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

As the colours of the wires in the lead may not

correspond with the coloured markings iden-

tifying the terminals in your plug, proceed as

follows:

Connect Green & Yellow wire to terminal

marked E or or coloured Green or Green &

Yellow.

Connect Brown wire to terminal marked L or

coloured Red.

Connect Blue wire to terminal marked N or

coloured Black.

If a 13 amp plug (BS 1363) is used it must be

fitted with a

13 amp fuse, either in the plug or adaptor or

at the distribution board.

If you are in any doubt regarding the electrical

supply to your machine, consult a qualified

electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN & YELLOW EARTH (E)

Disposing of the appliance:

When disposing of the appliance please re-

move the plug by cutting the mains cable as

close as possible to the plug body and dispo-

se of it as described on the previous page.

! The washer-dryer should not be installed in

an outdoor environment, not even where the

area is sheltered, because it may be very dan-

gerous to leave it exposed to damp, rain and

thunderstorms.

! When the washer-dryer is installed, the mains

socket must be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent

or dangerously compressed.

! The power supply cable must only be repla-

ced by an authorised serviceman.

Warning! The company denies all liability if and

when these norms are not respected.

The first wash cycle

Once the appliance has been installed, and

before you use it for the first time, run a wash

cycle with detergent and no laundry, using

wash cycle number auto clean (see “Cleaning

the washer-dryer”).

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

Technical data

Model RD 1076 J

Dimensions

width 59.5 cm

height 85 cm

depth 60,5 cm

Capacity

from 1 to 10 kg for the wash

programme

from 1 to 7 kg for the drying

programme

Electrical

connections

please refer to the technical

data plate fixed to the machine

Water con-

nections

maximum pressure

1 MPa (10 bar)

minimum pressure

0.05 MPa (0.5 bar)

drum capacity 71 litres

Spin speed up to 1600 rotations per

minute

Energy

rated

programmes

according to

regulation

EN 50229

Wash: programme 8; tem-

perature 60°C; using a load

of 10 kg.

Drying: the greater load

(7kg) must be dried by se-

lecting the “EXTRA” dryness

level.

The remainder of the load

must be dried by selecting

the “EXTRA” dryness level:

the load must consist of 3

sheets, 2 pillowcases and

1 hand towel.

This appliance conforms to

the following EC Directives:

- 2004/108/EC (Electroma-

gnetic Compatibility)

- 2006/95/EC (Low Voltage)

- 2012/19/EU (WEEE)

Cleaning the pump

The washer-dryer is fitted with a self-cleaning

pump which does not require any maintenan-

ce. Sometimes, small items (such as coins or

buttons) may fall into the pre-chamber which

protects the pump, situated in its bottom part.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. using a screwdri-

ver, remove the

cover panel on the

lower front part of the

washer-dryer (see

figure);

2. unscrew the lid

by rotating it anti-

clockwise (see figu-

re): a little water may

trickle out. This is

perfectly normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Care and maintenance

Cutting off the water and electri-

city supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system

inside the washer-dryer and help to prevent

leaks.

• Unplug the washer-dryer when cleaning it

and during all maintenance work.

Cleaning the washer-dryer

• The outer parts and rubber components

of the appliance can be cleaned using a soft

cloth soaked in lukewarm soapy water. Do not

use solvents or abrasives.

• The washer-dryer has a auto clean pro-

gramme for its internal parts that must be run

with no load in the drum.

To help the wash cycle you may want to use

either the detergent (i.e. a quantity 10% the

quantity specified for lightly-soiled garments)

or special additives to clean the washer-dryer.

We recommend running a cleaning program-

me every 40 wash cycles.

To activate the programme, press the but-

ton for 5 seconds then press START/PAUSE

to start the programme, which will last roughly

70 minutes.

Cleaning the detergent dispenser

drawer

Remove the dispen-

ser by raising it and

pulling it out (see

figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of

your appliance

• Always leave the porthole door ajar in order

to prevent unpleasant odours from forming.

Precautions and tips

! This washer-dryer was designed and constructed in

accordance with international safety regulations. The fol-

lowing information is provided for safety reasons and must

therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance can be used by children aged

from 8 years and above and persons with

reduced physical, sensory or mental capabi-

lities or lack of experience and knowledge if

they have been given supervision or instruction

concerning use of the appliance in a safe way

and understand the hazards involved. Children

shall not play with the appliance. Cleaning and

user maintenance shall not be made by children

without supervision.

– Do not dry unwashed items in the tumble dryer.

– Items that have been soiled with substan-

ces such as cooking oil, acetone, alcohol,

petrol, kerosene, spot removers, turpentine,

waxes and wax removers should be washed

in hot water with an extra amount of deter-

gent before being dried in the tumble dryer.

– Items such as foam rubber (latex foam),

shower caps, waterproof textiles, rubber

backed articles and clothes or pillows fitted

with foam rubber pads should not be dried in

the tumble dryer.

– Fabric softeners, or similar products,

should be used as specified by the fabric

softener instructions.

– The final part of a tumble dryer cycle occurs

without heat (cool down cycle) to ensure that

the items are left at a temperature that ensures

that the items will not be damaged.

WARNING: Never stop a tumble dryer before

the end of the drying cycle unless all items

are quickly removed and spread out so that

the heat is dissipated.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not open the detergent dispenser drawer while the

machine is in operation.

• Do not touch the drained water as it may reach extreme-

ly high temperatures.

• Never force the porthole door. This could damage the

safety lock mechanism designed to prevent accidental

opening.

• If the appliance breaks down, do not under any circum-

stances access the internal mechanisms in an attempt

to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group of two

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washer-dryer, make sure

the drum is empty.

• During the drying phase, the door tends to get quite hot.

• Do not use the appliance to dry clothes that

have been washed with flammable solvents

(e.g. trichlorethylene).

• Do not use the appliance to dry foam rubber

or similar elastomers.

• Make sure that the water tap is turned on during

the drying cycles.

• Children of less than 3 years should be kept

away from the appliance unless continuou-

sly supervised.

• Remove all objects from pockets such as

lighters and matches.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2012/19/EU on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents and

laundry”).

Programme Key: the Programme Key inside the deter-

gent dispenser shows all the available programmes toge-

ther with a graphical guide on how to use the individual

dispenser compartments.

ON/OFF button : press this briefly to switch the ma-

chine on or off. The START/PAUSE indicator light, which

flashes slowly in a green colour shows that the machine

is switched on. To switch off the washer-dryer during the

wash cycle, press and hold the button for approximately 3

seconds; if the button is pressed briefly or accidentally the

machine will not switch off. If the machine is switched off

during a wash cycle, this wash cycle will be cancelled.

WASH CYCLE SELECTOR KNOB: used to set the desired

wash cycle (see “Table of programmes and wash cycles”).

FUNCTION button: press the button to select the desired

function. The corresponding indicator light on the display

will switch on.

AUTO CLEAN button: press to clean the machine’s inter-

nal parts (see “Cleaning the washer-dryer”).

DIRECT INJECTION button: press to select the DIRECT

INJECTION option.

MULTI RINSE button : press to select the desired

rinse type.

SPIN button : press to reduce or completely exclude

the spin cycle - the value is indicated on the display.

TEMPERATURE button : press to decrease the tempe-

rature: the value will be shown on the display.

DRYING button : press to decrease or exclude drying;

the selected drying level or time will appear on the display.

DRY ONLY

(DRYING ONLY)

button : press to run the

drying cycle only.

KEY LOCK button : to activate the control panel

lock, press and hold the button for approximately 2

seconds. When the display visualises “KEY LOCK ON” the

control panel is locked (apart from the ON/OFF button).

This means it is possible to prevent wash cycles from

being modified accidentally, especially where there are

children in the home. To deactivate the control panel lock,

press and hold the button for approximately 2 seconds.

DELAY button : press to set a delayed start time for

the selected wash cycle. The delay time will be shown on

the display.

START/PAUSE button with indicator light: when the gre-

en indicator light flashes slowly, press the button to start a

wash cycle. Once the cycle has started the indicator light

will remain lit in a fixed manner. To pause the wash cycle,

press the button again; the indicator light will flash in an

orange colour. If the symbol is not illuminated, the door

may be opened. To start the wash cycle from the point at

which it was interrupted, press the button again.

Standby mode

This washer-dryer, in compliance with new energy saving

regulations, is fitted with an automatic standby system

which is enabled after about 30 minutes if no activity is

detected. Press the ON-OFF button briefly and wait for the

machine to start up again.

Consumption in off-mode: 0,5 W

Consumption in Left-on: 8 W

Description of the washer-dryer

Control panel

TEMPERATURE

button

Detergent dispenser drawer

FUNCTION

button

ON/OFF

button

SPIN

button

START/PAUSE

button with indicator light

KEY LOCK

button

DELAY

button

MULTI

RINSE

button

DISPLAY

AUTO

CLEAN

button

DIRECT

INJECTION

button

Programme

Key

WASH

CYCLE

SELECTOR

KNOB

DRY ONLY

(DRYING ONLY)

button

DRYING

button

The display is useful when programming the machine and provides a great deal of information.

The following will appear in area A: the icon and programme selected, the washing and drying phases and time remaining to

the end of the cycle.

Area B will include the two intensity levels relative to the DIRECT INJECTION option.

The indicator lights relative to the available functions appear in area C.

Area D will have the time remaining to the start of the selected programme if the DELAY function was set.

String E shows the maximum spin speed value (this depends on the selected wash cycle); if the programme does not inclu-

de the spin cycle, the dimly lit “--” symbol will appear in the area.

Area F will visualise the temperature value selectable on the basis of the set programme; if the temperature of the program-

me cannot be set, the area will show the symbol “--” dimly lit.

Door locked symbol

If the symbol is lit, this indicates that the washer-dryer door is blocked to prevent it from being opened accidentally. To pre-

vent any damage from occurring, wait for the symbol to switch itself off before opening the appliance door.

N.B.: if the DELAY function has been activated, the door cannot be opened; pauses the machine by pressing the START/

PAUSE button if you wish to open it.

! The first time the machine is switched on, you will be asked to select the language and the display will automatically show

the language selection menu.

To select the desired language press the X and Y buttons; to confirm the selection press the Z button.

To change the language switch off the machine and press buttons G, H, I simultaneously until an alarm is heard: the

language-selection menu will be displayed again.

! To change the display luminosity, which by default is set to the highest value, switch the machine off then simultaneously

press buttons G, L and M until the buzzer sounds. Press buttons X and Y to choose the desired level of luminosity then

confirm by pressing button Z.

! During the wash cycle or when the DELAY function has been enabled, if the user does not interact with the display for 1

minute the “SCREEN SAVER” activates. To return to the previous window, simply press any button.

Display

2:55

90° 1200 -- h

COTTON

X Z

L M

How to run a wash cycle or a

drying cycle

1. SWITCH THE MACHINE ON. Press the On/Off button ;

the text HOTPOINT will appear on the display and the START/

PAUSE indicator light will flash slowly in a green colour.

2. LOAD THE LAUNDRY. Open the porthole door. Load

the laundry, making sure you do not exceed the maximum

load value indicated in the table of programmes on the

following page.

3. MEASURE OUT THE DETERGENT. Open the

detergent dispenser drawer and pour the detergent into

the relevant compartments as described in “Detergents

and laundry”.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Use the WASH CYCLE

SELECTOR knob to select the desired wash cycle; the

name of the wash cycle will appear on the display. A

temperature and spin speed is set for each wash cycle;

these may be adjusted. The duration of the cycle will

appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons:

Modifying the temperature and/or spin speed. The

machine automatically selects the maximum temperature

and spin speed set for the selected wash cycle; these

values cannot therefore be increased. The temperature

can be decreased by pressing the button, until the cold

wash (the display will visualise the “--” symbol) setting is

reached. The spin speed may be progressively reduced by

pressing the button, until it is completely excluded (the

display will visualise the “--” symbol). If these buttons are

pressed again, the maximum values are restored.

! Exception: if the 5 programme is selected, the

temperature can be increased up to a value of 40°C.

! Exception: if the 7 programme is selected, the

temperature can be increased up to a value of 90°C.

! Exception: if the 9 programme is selected, the

temperature can be increased up to a value of 60°C.

Setting a delayed start.

To set a delayed start for the selected programme, press

the corresponding button repeatedly until the required

delay period has been reached. To remove the delayed

start function press the button until the text “-- h” appears

on the display.

Setting the drying cycle.

The desired drying cycle type may be set by pressing the

DRYING button once or several times. Two options are

available:

A - Based on the how damp the clothes are once they

have been dried:

Iron: suitable for clothes which will need ironing afterwards.

the remaining dampness softens creases, making them

easier to remove.

Hanger: ideal for clothes which do not need to be dried fully.

Cupboard: suitable for laundry which can be put back in a

cupboard without being ironed.

Extra: suitable for garments which need to be dried

completely, such as sponges and bathrobes.

B - Based on a set time period: between 30 and 180 minutes.

To exclude the drying phase press the relevant button until

the text OFF appears on the display.

If your laundry load to be washed and dried is much greater

than the maximum stated load, perform the wash cycle, and

when the cycle is complete, divide the garments into groups

and put some of them back in the drum. At this point, follow

the instructions provided for a “Dry only” cycle. Repeat this

procedure for the remainder of the load. A cooling-down

period is always added to the end of each drying cycle.

Dry only

Press button to perform the drying-only cycle.

After selecting the desired cycle (compatible with the type

of garments), press button to exclude the washing

phase and start the drying phase at the maximum level for

the selected cycle. The drying level or time may be set and

changed by pressing the drying button . (Not compati-

ble with cycles 1-2-3-4 and 14).

Set the rinse type.

Option makes it possible to select the desired rinse

type for sensitive skin. Press the button once for the “Extra

+1” level, which makes it possible to select an additional

rinse after the standard cycle rinse and remove all traces

of detergent. Press the button again for the “Extra +2”

level, which makes it possible to select two additional

rinses to the standard cycle rinses; it is recommended

for very sensitive skin. When the button is pressed for the

third time, the “Extra +3” level is set, thus allowing the

selection of 3 rinses in addition to the standard cycle’s

rinses. The option - started with cycles at a temperature of

40°C - makes it possible to remove major allergens such

as pollen, cat and dog hair. With cycles at a temperature

higher than 40° a very good level of antiallergic protection

is achieved. Press the button again to go back to the

“Normal rinse” rinse type. If the current adjustment can

be neither set nor changed, the display will show “No

Selection” or “No Change”.

Modifying the cycle settings.

• Press the button to enable the function; the relevant

indicator light on the display will light up.

• Press the button again to disable the function; the

relevant indicator light on the display will switch off.

! If the selected function is incompatible with the set

programme, the relevant indicator light will appear dimly lit;

in addition, the incompatibility will be signalled by a buzzer

(3 beeps) and the wording “No Selection” will appear on

the display.

! If the selected function is incompatible with another

previously set function, the wording “No Selection” will

appear on the display and the function will not be enabled.

! The functions may affect the recommended load value

and/or the duration of the cycle.

7. START THE PROGRAMME. Press the START/PAUSE

button. The corresponding indicator light will become

green, remaining lit in a fixed manner, and the door will be

locked (the DOOR LOCKED symbol will be on). During

the wash cycle, the name of the phase in progress will

appear on the display. To change a wash cycle while it is in

progress, pause the washer-dryer using the START/PAUSE

button (the START/PAUSE indicator light will flash slowly in

an orange colour); then select the desired cycle and press

the START/PAUSE button again. To open the door while

a cycle is in progress, press the START/PAUSE button; if

the DOOR LOCKED symbol is switched off the door

may be opened. Press the START/PAUSE button again

to restart the wash cycle from the point at which it was

interrupted.

8. THE END OF THE WASH CYCLE. This will be indicated

by the text “CYCLE END” on the display; when the DOOR

LOCKED symbol switches off the door may be opened.

Open the door, unload the laundry and switch off the machine.

! If you wish to cancel a cycle which has already begun, press

and hold the button. The cycle will be stopped and the

machine will switch off.

Direct Injection

The washer-dryer is equipped with the innovative technology

«Direct Injection» which pre-mixes water and detergent, thus

immediately activating the detergent’s cleaning principles.

This active emulsion is directly introduced into the drum of the

washer-dryer and penetrates the fibres with more efficacy in

cleaning even heavily soiled garments at low temperatures,

fully preserving colours and fabrics.

The mode «Power» ensures the best cleaning performance

and the mode «EcoEnergy» allows more energy saving.

Wash cycles and functions

Table of wash cycles

Wash functions

! If the selected function is incompatible with the set pro-

gramme, the relevant indicator light will appear dimly lit; in

addition, the incompatibility will be signalled by a buzzer

(3 beeps) and the wording “No Selection” will appear on

the display.

! If the selected function is incompatible with another pre-

viously set function, the wording “No Selection” will appear

on the display and the function will not be enabled.

Steam

This option enhances washing performance by generating

steam during the wash cycle to remove any bacteria from

the fibres, which are treated at the same time. Place the

laundry in the drum, choose a compatible programme and

select option .

! The steam generated during the operation of the washing

machine may cause the porthole door to become hazy.

1) Test wash cycle in compliance with regulation EN 50229: set wash cycle 8 with a temperature of 60°C.

2) Long wash cycle for cottons: set programme 8 at temperature 40°C and press the DIRECT INJECTION button under “Power” mode.

3) Long wash cycle for synthetics: set wash cycle 9 with a temperature of 40°C.

* If you select programme and exclude the spin cycle, the machine will drain only.

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-

ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

Wash cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Drying

Detergents

Max. load

(kg)

Cycle dura-

tion

Wash

Fabric

softener

ANTI CREASE

The duration of the wash cycle can be checked on the display.

1Daily Wash & Dry (Daily Mix Wash & Dry) 40° 800    3

2Shirts Wash & Dry 40° 1000    2

3Pre Iron - - - - - 1,5

4Steam Refresh - - - - - 2

DAILY CLEAN

5Anti-Stain Turbo 45’ (Anti Stain Turbo 45’) 20°

(Max. 40°C) 1200    5,5

6Anti-Stain Power 20°C (Anti Stain Power 20°C) 20° 1600    10

7Cotton: lightly soiled resistant and delicate colours. 40°

(Max. 90°C) 1600    10

8Eco Cotton

60°/40°

(1-2): heavily soiled whites and resistant colours. 60° 1600    10

9Synthetics (3): lightly soiled resistant colours. 40°

(Max. 60°C) 1000    5

SPECIALS

10 Multicolour (Multi Colour) 40° 1600    10

11 Ultradelicates (Ultra Delicates) 30° --    1

12 Wool: for wool, cashmere, etc. 40° 800    2,5

13 Sport 40° 600    4,5

14 Fast (Fast 30’) (**): to refresh lightly soiled garments quickly (not suitable for wool, silk

and clothes which require washing by hand). 30° 800    4

Partial Programmes

Rinse - 1600 -10

Spin + Pump out - 1600 - - 10

Pump out only * --- - - - 10

** If a drying cycle is also programmed, the machine will run a “wash+dry” programme lasting 45’ with maximum spin speed and a 1kg laundry load.

Detergent dispenser drawer

Good washing results also depend on the correct dose of

detergent: adding too much detergent will not necessarily

result in a more efficient wash, and may in fact cause a

build up on the inside of your appliance and contribute to

environmental pollution.

! Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

! Do not use hand washing detergents because these

create too much foam.

Open the detergent di-

spenser drawer and pour

in the detergent or washing

additive, as follows.

! Do not pour detergent into

the middle compartment (*).

compartment 1: Deter-

gent for the wash cycle

(powder or liquid)

If liquid detergent is used, it is recommended that the

removable plastic partition A (supplied) be used for proper

dosage. If powder detergent is used, place the partition

into slot B.

compartment 2: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Empty all garment pockets and check the buttons.

• Do not exceed the listed values, which refer to the weight

of the laundry when dry: see “Table of wash cycles”.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Special wash cycles

Daily Wash & Dry use programme 1 to wash and dry

mixed garments (cotton and synthetics). This cycle may be

used to wash and dry loads of up to 3 kg; we recommend

the use of liquid detergent.

The use of the steam in this programme is optimised to re-

duce the formation of creases on garments, making them

easier to iron.

Shirts Wash & Dry: use programme 2 to wash and dry

shirts and T-shirts in different fabrics and colours to ensure

maximum care. This cycle may be used to wash and dry

loads of up to 2 kg. To achieve optimum results, use liquid

detergent and pre-treat cuffs, collars and stains. The use of

the steam in this programme is optimised to reduce the for-

mation of creases on garments, making them easier to iron.

Pre Iron: use this programme immediately before ironing;

max. 1.5 kg load. The use of the steam in this programme

is optimised to reduce the formation of creases on gar-

ments, making them easier to iron.

Steam Refresh: for refreshing garments, neutralised unple-

asant odours and relaxing the fibres by delivering steam into

the drum. The garments will be damp at the end of the cycle.

Anti-Stain Turbo 45’: this cycle ensures excellent stain

removal capacity even at 20°C in just 45 minutes. The tem-

perature of this cycle can be increased up to 40°C.

Anti-Stain Power 20°C: this programme ensures ma-

ximum stain removal capacity with no need for pre-treat-

ment at low temperatures, preserving fabrics and colours.

Multicolour: for washing coloured cotton garments. This

programme is optimised to keep colours bright even after

repeated washing.

Ultradelicates: use programme 11 to wash very delicate

garments having strasses or sequins.

We recommend turning the garments inside out before washing

and placing small items into the special bag for washing delica-

tes. Use liquid detergent on delicate garments for best results.

When selecting an exclusively time-based drying function,

a drying cycle is performed at the end of the wash cycle

that is particularly delicate, thanks to light handling and

appropriate temperature control of the water jet.

The recommended durations are:

1 kg of synthetic garments --> 165 min

1 kg of synthetic and cotton garments --> 180 min

1 kg of cotton garments --> 180 min

The degree of dryness depends on the load and fabric

composition.

Wool - Woolmark Apparel Care - Green:

the wool wash cycle of this machine has been approved by The

Woolmark Company for the washing of wool garments labelled

as “hand wash” provided that the products are washed according

to the instructions on the garment label and those issued by the

manufacturer of this washer-dryer. (M1135)

Sport: for washing lightly soiled sports clothing (tracksuits,

shorts, towels, etc.); for best results, we recommend not

exceeding the maximum load indicated in the “Table of

wash cycles”. We recommend using liquid detergent, and

adding the amount suitable for a half-load.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and

to distribute the load in a uniform manner, the drum rotates

continuously at a speed which is slightly greater than the

washing rotation speed. If, after several attempts, the load is

not balanced correctly, the machine spins at a reduced spin

speed. If the load is excessively unbalanced, the washer-

dryer performs the distribution process instead of spinning.

To encourage improved load distribution and balance, we

recommend small and large garments are mixed in the load.

Detergents and laundry

Troubleshooting

Your washer-dryer could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Product Guaran-

tee and Repair Information”), make sure that the problem cannot be solved easily using the following list.

Problem:

The machine does not switch on.

The wash cycle does not start.

The machine does not dry.

The clothes are too hot when the

drying cycle is finished.

The washer-dryer does not take in

water (the text “NO WATER, Turn

tap on” appears on the display).

The machine continuously fills with

water and continually drains away

or Water left in the drum

or Stuck on wash.

The machine does not drain or spin

- (error lights flashing).

The machine does spin.

The machine does not heat or poor

wash results.

The programme takes too long.

The Display sticks at one ‘time to

end’ for more than 1 Minute or the

Display changes the estimated ‘Time

to End’ during the programme.

The machine vibrates a lot during

the spin cycle.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or not enough to make contact.

• There is no power to the socket, or the fuse has blown in the mains plug.

• The door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been turned on to allow water to flow into the machine.

• A delayed start has been set.

• Check the 2 sections above.

• DRYING is in the OFF position.

• A cooling-down period is always added to the end of each drying cycle. If the

clothes appear too hot to handle leave the door open to allow to cool further

before removing from the machine.

• The water inlet hose is kinked.

• The water inlet hose is not connected to the water supply.

• The water pressure is too low.

• The water tap has not been turned on to allow water to flow into the machine.

• There is no water supply to the house.

• The inlet valve filter is blocked.

• The START/PAUSE button has not been pressed.

• The top of the drain hose is too low - It must be fitted at a height between 65

and 100 cm from the floor (see “Installation”).

• The drain hose is connected incorrectly to the sink trap allowing water to run

into the machine, the drain hose must be positioned higher than the bottom of

the sink to prevent water flowing down the drain hose.

• The end of the drain hose has been pushed too far down the standpipe, the

‘U’ bracket should be fitted 100 mm from the end of the drain hose.

• The Pump filter is blocked.

• The drain hose is kinked (see “Installation”).

• New Installation - The blanking cap or spigot has not been removed if

connected under a sink.

• The drain hose or sink trap is blocked.

• The Spin Speed is set to “--”.

• The ‘Temperature’ is set to “--”.

• Programme times will vary due to water pressure, the incoming water temperature

and if the wash load goes out of balance. This will increase the programme times

accordingly (see ‘ The machine wont spin properly’ next page).

• The display time is for guidance only - it is not a precise time to finish and

may vary.

• The feet have not been adjusted, enabling the machine to rock.

• New Installation - Either the Transit Bolts including the plastic spacers, or the

Polystyrene Packaging have not been removed when installing the machine.

• The machine is trapped between cabinets and/or walls.

• The load is in a slight out of balance condition and machine is spinning, but at

a lower speed.

The machine is noisy.

The machine wont spin properly.

The machine leaks from the

dispenser.

The machine leaks (other than

dispenser).

The machine is locked and the

display flashes, indicating an error

code (e.g. F-01, F-..).

The machine smells.

The machine door cannot be

opened.

Door Seal damaged at the bottom.

The water level is too low when

the machine is washing.

There is too much foam.

The machine just ‘beeps’ when a

programme or option is selected

(Key Lock led is lit).

After completing the programme,

or before starting a programme,

the machine has turned itself off

(no lights).

General.

• There will always be some motor, pump and drum noise during spin.

• Out of Balance detected when attempting to go into a spin cycle - If this

happens the machine will continue to try to repeat the distribution of the load

required before the machine will go into higher spin speeds - This will increase

the programme time accordingly. This is a safety feature to prevent damage.

Out of Balance can be caused by washing a single heavy item (eg duvet, quilt,

etc). - Try the programme again using a different load.

• The dispenser drawer is blocked with detergent and requires cleaning.

• The water pressure is too high and requires turning down - turn down the tap

on the water supply pipe slightly and try again.

• The machine is tilting forwards - It must be level when in its final position.

• The fill hose is loose, check both the cabinet and tap ends.

• The fill hose is tight but still leaks, if so replace the rubber washers, or the fill

hose is missing the rubber washer.

• The drain hose is not fixed in properly.

• Switch off the machine and unplug it, wait for approximately 1 minute and then

switch back on again. If the problem persists contact Technical Assistance

Centre.

• The machine requires a service wash. Run a auto clean wash cycle with deter-

gent and no laundry.

• The door will not open until the door lock indicator light goes out shortly after

the program has finished.

• If there is no power to the machine you need to perform the manual unlocking

procedure.

• The door seal has drainage holes at the bottom - This is normal.

• The water level is correct if it can be seen at the bottom of the door.

• The detergent is not suitable for machine washing (it should display the text

‘for washer-dryers’ or ‘hand and machine wash’ or the like).

• Too much detergent was used - less detergent is required in soft water.

• Deactivate the Key Lock feature by pressing and holding in the ‘KEY LOCK’

button for 2 seconds.

• To comply with new energy saving regulations the machine is fitted with an

automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate

the machine, it can then either be switched off or a new programme selected.

• Your washer-dryer contains sensors that monitor progress during the wash cycle

(eg: Water Levels, Temperatures, Out of Balance loads, Wash time/progress).

Normally, if your machine successfully completes the cycle, there is unlikely to

be anything wrong!

Remember, you will be charged for a service call for problems caused by incorrect installation, as indicated on

pages 2 to 4.

Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.

Do not wash items which do not have a wash label, or wash items that are not intended as machine washable.

Product Guarantee and

Repair Information

Guarantee

12 Months Parts and Labour Guarantee

Your appliance has the benefit of our manufacturer’s

guarantee, which covers the cost of breakdown

repairs for twelve months from the date of purchase.

This gives you the reassurance that if, within that

time, your appliance is proven to be defective

because of either workmanship or materials, we will,

at our discretion, either repair or replace the appliance

at no cost to you:

This guarantee is subject to the following conditions:

- The appliance has been installed and operated

correctly and in accordance with our operating and

maintenance instructions.

- The appliance is used only on the electricity or gas

supply printed on the rating plate.

- The appliance has been used for normal domestic

purposes only.

- The appliance has not been altered, serviced,

maintained, dismantled, or otherwise interfered with

by any person not authorised by us.

- Any repair work must be undertaken by us or our

appointed agent.

- Any parts removed during repair work or any

appliance that is replaced become our property.

- The appliance is used in the United Kingdom or

Republic of Ireland.

The guarantee does not cover:

- Damage resulting from transportation, improper

use, neglect or interference or as a result of improper

installation.

- Replacement of any consumable item or accessory.

These include but are not limited to: plugs, cables,

batteries, light bulbs, fluorescent tubes and starters,

covers and filters.

- Replacement of any removable parts made of glass

or plastic.

THIS GUARANTEE WILL NOT APPLY IF THE

APPLIANCE HAS BEEN USED IN COMMERCIAL

OR NON-DOMESTIC PREMISES.

Recycling and Disposal Information

As part of Hotpoint’s continued commitment to

helping the environment, Hotpoint reserves the right

to use quality, recycled components to keep down

customer costs and minimise material wastage.

Please dispose of packaging and old appliances

carefully. To minimise the risk of injury to children,

remove the door, plug, and cut the mains cable

off flush with the appliance. Dispose of these parts

separately to ensure that the appliance can no longer

be plugged into mains socket, and the door cannot

be locked shut.

Repairs and After Sales

For product help and advice, repairs, spare parts or

accessories, we’re here to help.

For local repair engineers - 03448 111 606

ROI - 0818 313 413

UK standard local rate applies

ROI local Irish rate applies

For Parts and Accessories visit:

parts.hotpoint.co.uk/shop

Please remember to register your appliance at

www.hotpointservice.co.uk to activate your 10 year

parts guarantee.

How to find your model and serial number:

195140855.02

10/2016

Indesit Company Spa

Viale Aristide Merloni, 47

60044 Fabriano (AN)

Italy