Hotpoint RD 1176 JD User Manual
Displayed below is the user manual for RD 1176 JD by Hotpoint which is a product in the Washer Dryers category. This manual has pages.
Related Manuals
www.hotpoint. eu/register
User Manual
GB
Quick Guide
THANK YOU FOR PURCHASING A HOTPOINT PRODUCT.
To receive more comprehensive assistance, register the
appliance on
www.hotpoint.eu/register
Before using the appliance carefully read the Health and Safety guide.
Before using the machine, it is imperative that the transport bolts are removed. For more
detailed instructions on how to remove them, see the Installation Guide.
CONTROL PANEL
1. ON/OFF button
2. DRYING button
3. DRY ONLY button
4. MULTI RINSE button
5. OPTION button
6. DIRECT INJECTION button
7. START/PAUSE button and indicator light
8. KEY LOCK button
9. DELAY button
10. SPIN button
11. TEMPERATURE button
12. AUTO CLEAN button
13. WASH CYCLE SELECTOR KNOB
14. Programme Key
WASH CYCLE TABLE
For all testing institutes:
2) Long cotton cycle: set programme 8 at temperature 40°C and press the DIRECT INJECTION
button under “Power” mode.
3) Long synthetics cycle: set cycle 9 at a temperature of 40°C.
* By selecting the cycle and excluding the spin cycle, the washer-dryer will drain only.
** If a drying cycle is also programmed, the machine will run a “wash+dry” programme lasting
45’ and a 1kg laundry load.
The cycle duration indicated on the display or instruction manual is an estimate based on
standard conditions. The actual duration may vary in relation to several factors, such as
the temperature and pressure of the incoming water, ambient temperature, amount of
detergent, load quantity and type, load balancing and any additional options selected.
1) Test programme in compliance with standard EN 50229 (Wash):
This cycle is designed for normally soiled cotton loads and is the most ecient in terms of
both electricity and water consumption; it should be used for garments washable at 60°C or
at 40°C. The actual washing temperature may dier from the indicated value.
Test programme in compliance with standard EN 50229 (Drying): select the 8 wash
programme and set the drying level to “EXTRA”, for both loads. The rst drying cycle must be
carried out with the nominal load.
PRODUCT DESCRIPTION
1.
3.
2.
5.
4.
7.
6.
8.
1. Top
2. Detergent dispenser drawer
3. Control panel
4. Handle
5. Porthole door
6. Drain pump (behind the plinth)
7. Plinth (removable)
8. Adjustable feet (2)
13 7
8
9
10
11
12
1 2 4
DISPLAY
5 6
3
Maximum load 11 kg
Power input in o mode 0.5 W / in left-on mode 8 W
Detergents and
Additives
Recommended
detergent
Wash cycle Temperature Maximum
spin
(r.p.m.)
Max.
load
(kg)
Duration
(Minutes)
Drying
Wash Fabric
softener Powder Liquid
Default Range 1 2
1 Daily Wash & Dry (Daily Mix Wash & Dry) 40 °C - 40 °C 800 3,0
The duration of the wash cycles can be checked on the display.
–
2 Shirts Wash & Dry 40 °C - 40 °C 1000 2,0 –
3Pre Iron – – – 1,5 – – – – –
4 Steam Refresh – – – 2,0 – – – – –
5Anti-Stain Turbo 45’ (Anti Stain Turbo 45’) 20 °C - 40 °C 1200 5,5 –
6 Anti-Stain Power 20°C (Anti Stain Power 20°C) 20 °C - 20 °C 1600 11,0 –
7 Cotton 40 °C - 90 °C 1600 11,0
8Eco Cotton
60°/40°
(1-2) 60 °C - 60 °C 1600 11,0
9 Synthetics (3) 40 °C - 60 °C 1000 5,0
10 Multicolour (Multi Colour) 40 °C - 40 °C 1600 11,0 –
11 Ultradelicates (Ultra Delicates) 30 °C - 30 °C -- 1,0 –
12 Wool 40 °C - 40 °C 800 2,5 –
13 Sport 40 °C - 40 °C 600 4,5 –
14 Fast (Fast 30') ** 30 °C - 30 °C 800 4,0 –
Rinse – – 1600 11,0 –– –
Spin + Pump out * – – 1600 11,0 – – – –
Required dosage Optional dosage
DETERGENT DISPENSER DRAWER
Compartment *:
Do not insert detergent in this compartment.
Compartment 1: Washing detergent (powder
or liquid)
If liquid detergent is used, the removable plastic
partition A (supplied) should be used for proper
dosage.
If powder detergent is used, place the partition
into slot B.
Compartment 2: Additives (fabric softeners, etc.)
The fabric softener must not exceed the “MAX” level.
! Use powder detergent for white cotton garments, for pre-washing, and
for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
1
2
A
B
*
14
WASH CYCLES
Follow the instructions on the symbols of the garment’s wash
care label. The value indicated in the symbol is the maximum
recommended temperature for washing the garment.
Daily Wash & Dry
use programme 1 to wash and dry mixed garments (cotton and
synthetics). This cycle may be used to wash and dry loads of up to 3 kg;
we recommend the use of liquid detergent.
The use of the steam in this programme is optimised to reduce the
formation of creases on garments, making them easier to iron.
Shirts Wash & Dry
Use programme 2 to wash and dry shirts and T-shirts in dierent fabrics
and colours to ensure maximum care. This cycle may be used to wash and
dry loads of up to 2 kg. To achieve optimum results, use liquid detergent
and pre-treat cus, collars and stains. The use of the steam in this
programme is optimised to reduce the formation of creases on garments,
making them easier to iron.
Pre Iron
Use this programme immediately before ironing; max. 1,5 kg load. The
use of the steam in this programme is optimised to reduce the formation
of creases on garments, making them easier to iron.
Steam Refresh
For refreshing garments, neutralised unpleasant odours and relaxing the
bres by delivering steam into the drum. The garments will be damp at
the end of the cycle.
Anti-Stain Turbo 45’
This cycle is ideal for washing daily stains in 45’. It is ideal for mixed fabrics
and coloured garments.
Anti-Stain Power 20°C
this programme ensures maximum stain removal capacity with no need
for pre-treatment at low temperatures, preserving fabrics and colours.
Cotton
Suitable for washing towels, underwear, table cloths, etc. made of
resistant linen and cotton that are moderately to heavily soiled.
Eco Cotton
Suitable for washing moderately soiled cotton garments. At 40°C and
60°C it is the standard cycle for washing cotton garments, and is the most
ecient in terms of combined water and electricity consumption.
Synthetics
Suitable for washing moderately soiled garments made of synthetic bres
(e.g. polyester, polyacrylic, viscose, etc.) or mixed synthetic-cotton bres.
Multicolour
for washing coloured cotton garments. This programme is optimised to
keep colours bright even after repeated washing.
Ultradelicates
For washing very delicate garments. It is advisable to turn the garments
inside out before washing them. For best results, use liquid detergent on
delicate garments.
We recommend turning the garments inside out before washing and
placing small items into the special bag for washing delicates. Use liquid
detergent on delicate garments for best results.
When selecting an exclusively time-based drying function, a drying cycle
is performed at the end of the wash cycle that is particularly delicate,
thanks to light handling and appropriate temperature control of the
water jet.
The recommended durations are:
1 kg of synthetic garments --> 165 min
1 kg of synthetic and cotton garments --> 180 min
1 kg of cotton garments --> 180 min
The degree of dryness depends on the load and fabric composition.
Wool - Woolmark Apparel Care - Green:
the wool wash cycle of this machine has been approved
by The Woolmark Company for the washing of wool
garments labelled as “hand wash” provided that the
products are washed according to the instructions on the
garment label and those issued by the manufacturer of
this washer-dryer. (M1135)
Sport
for washing lightly soiled sports clothing (tracksuits, shorts, towels, etc.);
for best results, we recommend not exceeding the maximum load
indicated in the “Wash cycles Table”. We recommend using liquid
detergent, and adding the amount suitable for a half-load.
Fast
For washing lightly soiled garments in a short time. Not suitable for wool,
silk and garments to be washed by hand.
Rinse
Designed for rinsing and spinning.
Spin + Pump out
Designed for spinning and draining the water.
DISPLAY
The display is useful when programming the machine and provides a
great deal of information.
The following will appear in area A: the icon and programme selected, the
washing and drying phases and time remaining to the end of the cycle.
Area B will include the two intensity levels relative to the DIRECT
INJECTION option. The indicator lights relative to the available functions
appear in area C. Area D will display the time remaining to the start of the
selected cycle if the DELAY function was set.
Area E will display the maximum available spin speed on the basis of the
set cycle; if the cycle does not include the spin cycle setting, the dimly lit
“--” symbol will appear in the area.
Area F will show the temperature value that can be selected on the basis
of the set cycle.
If the cycle does not include setting of the temperature, the dimly lit “--”
symbol will appear in the area.
! To change the display luminosity, which by default is set to the highest
value, switch the machine o then simultaneously press buttons G, L and
M until the buzzer sounds.
Press buttons X and Y to choose the desired level of luminosity then
conrm by pressing button Z.
! During the wash cycle or when the DELAY function has been enabled, if
the user does not interact with the display for 1 minute the SCREEN SAVER
activates. To return to the previous window, simply press any button.
Locked door indicator
When lit, the symbol indicates that the door is locked. To prevent any
damage, wait until the symbol turns o before opening the door.
To open the door while a cycle is in progress, press the START/PAUSE
button ; if the symbol is o, the door can be opened.
FIRSTTIME USE
Once the appliance has been installed, and before it is used for the rst
time, run a wash cycle with detergent and no laundry, by setting the “Auto
Clean” cycle.
DAILY USE
Prepare the laundry by following the suggestions appearing under the
“TIPS AND SUGGESTIONS” section.
- Press the ON/OFF button ; “HOTPOINT” will appear on the display; the
indicator light relative to the START/PAUSE button will ash slowly green.
- Open the door. Load the laundry while making sure not to exceed the
maximum load quantity indicated in the wash cycle table.
- Pull out the detergent dispenser drawer and pour the detergent into the
relevant compartments, as described in the “DETERGENT DISPENSER
DRAWER” section.
- Close the door.
- Use the WASH CYCLE selector knob to select the desired wash cycle: the
cycle’s name will appear on the display; the cycle will be associated with a
specic temperature and spin speed which can be modied. The duration
of the cycle will appear on the display.
- Modify the temperature and/or spin speed: the machine automatically
selects the maximum temperature and spin speed set for the selected
wash cycle; these values cannot therefore be increased. Pressing the
button gradually reduces the temperature down to the cold wash setting
(the “--” symbol will appear on the display). Pressing the button
gradually reduces the spin speed until it is completely excluded (the “--”
symbol will appear on the display). Pressing the buttons further restores
the maximum allowed values for the selected cycle.
- Select the desired options.
- Press the START/PAUSE button to start the wash cycle; the relative
indicator light will light up steady green and the door will lock (
symbol on).
PAUSING A CYCLE
To pause the wash cycle, press the START/PAUSE button again; the
indicator light will ash amber. To start the wash cycle from the point at
which it was interrupted, press the START/PAUSE button again.
ADDITIONAL GARMENTS
An icon on the display will signal when additional garments can be introduced
into the washing machine, without decreasing the washing performance.
To add garments, rst stop the washing machine by pressing the START/
PAUSE button then open the door and insert them.
Press the START/PAUSE button again to restart the wash cycle from
the point at which it was interrupted.
CHANGING A RUNNING WASH CYCLE
To change a wash cycle while it is in progress, pause the washing machine
using the START/PAUSE button (the relative indicator light will ash amber),
then select the desired cycle and press the START/PAUSE button again.
2:55
90° 1200 -- h
--
COTTON
H
G
Y
X Z
I
L M
A
B
C
C
D
E
C
F
! The “Programme key” situated inside the detergent dispenser shows all the
available wash cycles together with a graphic guide on how to use the
individual dispenser compartments.
! To cancel a cycle that has already begun, press and hold the ON/OFF
button. The cycle will be stopped and the machine will switch o.
AT THE END OF THE WASH CYCLE
This will be indicated by the word “CYCLE END” on the display; when the
symbol switches o, the door may be opened. Open the door, unload the
laundry and switch o the machine. If you do not press ON/OFF button, the
washing machine will switch o automatically after about a half of an hour.
OPTIONS
- If the selected function is incompatible with the set wash cycle, the
relevant indicator light will appear dimly lit; the incompatibility will also
be signalled by a buzzer (3 beeps) and the wording “Not Selection” will
appear on the display.
- If the selected function is incompatible with another previously set
function, the wording “Not Selection” will appear on the display and
the function will not be enabled.
Steam
This option enhances washing performance by generating steam during
the wash cycle to remove any bacteria from the bres, which are treated
at the same time. Place the laundry in the drum, choose a compatible
programme and select option .
! The steam generated during the operation of the washer-dryer may
cause the porthole door to become hazy.
Delay
To set a delayed start for the selected cycle, press the corresponding
button repeatedly until the desired delay period is reached. To remove
the delayed start setting, press the button until “-- h” appears on the
display.
Temperature
Each wash cycle has a pre-dened temperature. To modify the
temperature, press the button. The value will appear on the display.
Spin
Each wash cycle has a pre-dened spin speed. To modify the spin speed,
press the button. The value will appear on the display.
Direct Injection
The washer-dryer is equipped with the innovative technology «Direct
Injection» which pre-mixes water and detergent, thus immediately
activating the detergent’s cleaning principles. This active emulsion is
directly introduced into the drum of the washer-dryer and penetrates the
bres with more ecacy in cleaning even heavily soiled garments at low
temperatures, fully preserving colours and fabrics.
The mode «Power» ensures the best cleaning performance and the mode
«EcoEnergy» allows more energy saving.
Drying
The desired drying cycle type may be set by pressing the DRYING button
once or several times. Two options are available:
A - Based on the how damp the clothes are once they have been dried:
Iron: suitable for clothes which will need ironing afterwards. the
remaining dampness softens creases, making them easier to remove.
Hanger: ideal for clothes which do not need to be dried fully.
Cupboard: suitable for laundry which can be put back in a cupboard
without being ironed.
Extra: suitable for garments which need to be dried completely, such as
sponges and bathrobes.
B - Based on a set time period: between 30 and 180 minutes.
To exclude the drying phase press the relevant button until the text OFF
appears on the display.
If your laundry load to be washed and dried is much greater than the
maximum stated load, perform the wash cycle, and when the cycle is
complete, divide the garments into groups and put some of them back in
the drum. At this point, follow the instructions provided for a “Dry only”
cycle. Repeat this procedure for the remainder of the load. A cooling-
down period is always added to the end of each drying cycle.
Dry only
Press button to perform the drying-only cycle.
After selecting the desired cycle (compatible with the type of garments),
press button to exclude the washing phase and start the drying
phase at the maximum level for the selected cycle. The drying level or
time may be set and changed by pressing the drying button .
Multi Rinse
This option allows for selecting the desired rinse type to protect sensitive
skin. Press the button once to set level “Extra +1”, which allows for
selecting an additional rinse to the standard cycle rinses and removing all
traces of detergent. Press the button again to set level “Extra +2”, which
allows for selecting two additional rinses to the standard cycle rinses; this
cycle is recommended for very sensitive skin. When the button is pressed
for the third time, the “Extra +3” level is set, which allows for selecting
3 additional rinses to the standard cycle rinses. When started with
cycles at a temperature of 40°C, this option makes it possible to remove
major allergens such as pollen and cat or dog hair. With cycles running
at temperatures higher than 40°C, an excellent level of anti-allergy
protection is achieved. Press the button again to return to the “Normal
Rinse” mode. If the current mode cannot be set nor changed, the display
will show “Not Selection” or “Not Change”.
KEY LOCK
To activate the control panel lock, press and hold the button for
roughly 2 seconds. When the display visualises “KEY LOCK ON”, the control
panel is locked (except for the ON/OFF button ). This will prevent
accidental modications to wash cycles, especially when children are at
home. To deactivate the control panel lock, press and hold the
button for approximately 2 seconds.
TIPS AND SUGGESTIONS
Divide the laundry according to:
Type of fabric (cotton, mixed bres, synthetics, wool, garments to be
hand-washed). Colour (separate coloured garments from whites, wash new
coloured garments separately). Delicates (small garments – such as nylon
stockings – and items with hooks – such as bras: insert them in a fabric bag).
Empty the pockets:
Objects such as coins or lighters can damage the washer-dryer and the
drum. Check all buttons.
CARE AND MAINTENANCE
Before performing cleaning and maintenance, switch the washer-dryer o
and disconnect it from the mains power. Do not use ammable liquids to
clean the washer-dryer.
Cutting o the water and electricity supplies
Turn o the water tap after every wash cycle. This will limit wear on the
hydraulic system inside the washer-dryer and help to prevent leaks.
Unplug the washer-dryer when cleaning it and during all maintenance work.
Cleaning the washer-dryer
The outer parts and rubber components of the appliance can be cleaned using
a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.
The washer-dryer has a “Auto Clean” cycle for its internal parts; it must be
run without any load in the drum.
To help the wash cycle you may want to use either the detergent (i.e. a
quantity 10% the quantity specied for lightly-soiled garments) or special
additives to clean the washer-dryer. We recommend running a cleaning
programme every 40 wash cycles.
To activate the cycle, press the button for 5 seconds then press START/
PAUSE to start the cycle, which will last roughly 70 minutes.
Cleaning the detergent dispenser drawer
Remove the dispenser drawer by lifting and pulling it outwards. Wash it
under running water; this procedure should be eected regularly.
Caring for the door and drum
Always leave the porthole door ajar in order to prevent unpleasant odours
from forming.
Cleaning the pump
The washer-dryer is tted with a Auto Clean pump which does not require
any maintenance. Small items (such as coins or buttons) may sometimes
fall into the protective pre-chamber situated at the base of the pump.
! Make sure that the wash cycle has ended and unplug the appliance.
To access the pre-chamber:
1. remove the covering panel on the front side of the machine by inserting
a screwdriver in the centre and sides of the panel and using it as a lever;
2. loosen the drainage pump cover by turning it anti-clockwise: it is
normal for some water to leak out;
3. clean the inside thoroughly;
4. screw the cover back on;
5. put the panel back in place, making sure the hooks slot in place before
pushing the panel onto the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If it is cracked or broken, it must
be replaced: during wash cycles, the high pressure of the water could
suddenly split the hose open.
! Never use hoses that have already been used.
LOAD BALANCING SYSTEM
Before every spin cycle, to avoid excessive vibrations before every
spin and to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the washing
rotation speed. If, after several attempts, the load is not balanced
correctly, the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washing machine performs the distribution
process instead of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are mixed in the load.
ACCESSORIES
Contact our Technical Assistance Service to check whether the following
accessories are available for this washer-dryer model.
Stacking kit
With this accessory you can secure the tumble dryer to the upper part of
your washer-dryer to save space and facilitate loading and unloading of
the tumble dryer.
TRANSPORT AND HANDLING
Do not lift the washer-dryer by gripping it from the upper section.
Unplug the appliance and close the water tap. Check that the door and
detergent dispenser drawer are tightly closed. Detach the lling hose from
the water tap then detach the drain hose. Empty all the water remaining in
the hoses and secure the latter so that they do not get damaged during
transport. Apply the transport bolts back on. Repeat, in reverse order, the
transport bolt removal procedure described in the “Installation instructions”.
Important: Not emptying contents from pockets may cause pump or drain
blockages, or may damage the machine.
Do not wash items which do not have a wash label, or wash items that are
not intended as machine washable.
DEMO MODE: to deactivate this function, switch the washing machine OFF.
Than press and hold “Start/Pause” button, within 5 seconds press also
“ON/OFF” button and hold both buttons for 2 seconds.
Anomalies Possible causes / Solution
The machine does not switch on. The appliance is not plugged into the socket fully, or not enough to make contact.
There is no power to the socket, or the fuse has blown in the mains plug.
The wash cycle does not start.
The door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been turned on to allow water to ow into the machine.
A delayed start has been set.
The washing machine does not ll with water
(“NO WATER, turn tap on” appears on the
display).
The water inlet hose is kinked.
The water inlet hose is not connected to the water supply.
The water pressure is too low.
The water tap has not been turned on to allow water to ow into the machine.
There is no water supply to the house.
The inlet valve lter is blocked.
The START/PAUSE button has not been pressed.
The machine continuously lls with water and
continually drains away or Water left in the
drum or Stuck on wash.
The top of the drain hose is too low - It must be tted at a height between 65 and 100 cm from the oor.
The drain hose is connected incorrectly to the sink trap allowing water to run into the machine, the drain hose must be
positioned higher than the bottom of the sink to prevent water owing down the drain hose.
The end of the drain hose has been pushed too far down the standpipe, the ‘U’ bracket should be tted 100 mm from the end
of the drain hose.
The machine does not drain or spin - (error
lights ashing).
The Pump lter is blocked.
The drain hose is kinked.
New Installation - The blanking cap or spigot has not been removed if connected under a sink.
The drain hose or sink trap is blocked.
The machine does spin. The ‘Spin’ Speed is set to “--”.
The machine does not heat or poor wash results. The ‘Temperature’ is set to “--”.
The programme takes too long. Programme times will vary due to water pressure, the incoming water temperature and if the wash load goes out of balance.
This will increase the programme times accordingly.
The Display sticks at one ‘time to end’ for more
than 1 Minute or the Display changes the
estimated ‘Time to End’ during the programme.
The display time is for guidance only - it is not a precise time to nish and may vary.
The washing machine vibrates a lot during the
spin cycle.
The feet have not been adjusted, enabling the machine to rock.
New Installation - Either the Transit Bolts including the plastic spacers, or the Polystyrene Packaging have not been removed
when installing the machine.
The machine is trapped between cabinets and/or walls.
The load is in a slight out of balance condition and machine is spinning, but at a lower speed.
The machine is noisy. There will always be some motor, pump and drum noise during spin.
The machine leaks from the
dispenser.
The dispenser drawer is blocked with detergent and requires cleaning.
The water pressure is too high and requires turning down - turn down the tap on the water supply pipe slightly and try again.
The machine is tilting forwards - It must be level when in its nal position.
The “Options” and START/PAUSE indicator
lights ash rapidly and the display visualises an
error code (e.g.: F-01, F-...).
Switch o the machine and unplug it, wait for approximately 1 minute and then switch back on again. If the problem persists
contact Technical Assistance Centre.
The machine smells. The machine requires a service wash. Run a auto clean wash cycle with detergent and no laundry.
The water level is too low when the machine is
washing. The water level is correct if it can be seen at the bottom of the door.
There is too much foam. The detergent is not suitable for machine washing (it should display the text
‘for washing machines’ or ‘hand and machine wash’ or the like).
General. Your washing machine contains sensors that monitor progress during the wash cycle (eg: Water Levels, Temperatures, Out of Balance
loads, Wash time/progress). Normally, if your machine successfully completes the cycle, there is unlikely to be anything wrong!
The washer-dryer does not dry.
The appliance is not plugged into the socket, or not enough to make contact.
There has been a power failure.
The appliance door is not shut properly.
A Delay Timer has been set.
DRYING is in the OFF position.
TROUBLESHOOTING
Your machine could occasionally fail to work. Before contacting the Technical Assistance Service, make sure that the problem cannot be easily solved
using the following list.
CLEANING & MAINTENANCE
For any cleaning and maintenance, switch o and unplug the washing machine.
Do not use ammable uids to clean the washing machine.
CLEANING THE OUTSIDE OF THE WASHING MACHINE
Use a soft damp cloth to clean the outer parts of the washing
machine.
Do not use glass or general purpose cleaners, scouring
powder or similar to clean the control panel – these
substances might damage the printing.
CHECKING THE WATER SUPPLY HOSE
Check the inlet hose regularly for brittleness and cracks. If
damaged, replace it by a new hose available through our
After-Sales Service or your specialist dealer.
Depending on the hose type:
If the inlet hose has a transparent coating, periodically check
if the colour intensies locally. If yes, the hose may have a leak
and should be replaced.
For water stop hoses: check the small safety valve inspection
window (see arrow). If it is red, the water stop function was
triggered, and the hose must be replaced by a new one.
For unscrewing this hose, press the release button (if
available) while unscrewing the hose.
CLEANING THE MESH FILTERS IN THE WATER SUPPLY HOSE
1. Close water tap and unscrew the inlet hose.
1
2
2. Clean the mesh lter at the hose’s end carefully with a
ne brush.
3. Now unscrew the inlet hose on the back of the washing
machine by hand. Pull out the mesh lter from the valve
on the back of the washing machine with pliers and
carefully clean it.
4. Insert the mesh lter again. Connect the inlet hose to
water tap and washing machine again. Do not use a tool
to connect the inlet hose. Open the water tap and check
that all connections are tight.
2
1
CLEANING THE DETERGENT DISPENSER
CLEANING THE WATER FILTER / DRAINING RESIDUAL WATER
Switch o and unplug the washing machine before cleaning the water lter or draining residual water. If you used a hot
wash programme, wait until the water has cooled down before draining any water.
Clean the water lter regularly, to avoid that the water cannot drain after the wash due to obstruction of the lter.
If the water cannot drain, the display indicates that the water lter may be clogged.
1. Remove the kick panel: Using a screwdriver, do that which
is shown in the following gure.
2. Container for the drained water:
Place a low and wide container under the water lter in
order to collect the residual water.
3. Drain the water:
Slowly turn the lter counter-clockwise until all the water
has come out. Allow the water to ow out without
removing the lter. Once the container is full, close the
water lter by turning it clockwise. Empty the container.
Repeat the procedure until all the water has been drained.
4. Remove lter: Lay a cotton cloth beneath the water lter,
which can absorb a small amount of rest water. Then
remove the water lter by turning it out anticlockwise.
5. Clean the water lter: remove residues in the lter and
clean it under running water.
6. Insert the water lter and reinstall the plinth: Reinsert the water
lter again by turning it in clockwise direction. Make sure to turn
it in as far as it goes; the lter handle must be in vertical position.
To test water tightness of the water lter, you can pour about 1
liter of water into the detergent dispenser. Then reinstall the
plinth.
1
2
Remove the dispenser by raising it and
pulling it out (see gure).
Wash it under running water; this
operation should be repeated frequently.
1
2
TRANSPORT AND HANDLING
Never lift the washing machine by holding it at the worktop.
1. Pull out the mains plug, and close the water tap.
2. Make sure that door and detergent dispenser are properly
closed.
3. Disconnect the inlet hose from the water tap, and remove
the drain hose from your draining point. Remove all rest
water from the hoses, and x them so that they cannot get
damaged during transport.
4. Ret the transport bolts. Follow the instructions for
removing the transport bolts in the “Installation Guide” in
reverse order.
Important: Do not transport the washing machine without
having xed the transport bolts.
AFTERSALES SERVICE
BEFORE CALLING THE AFTERSALES SERVICE
1. See if you can solve the problem by yourself with the help
of the suggestions given in the TROUBLESHOOTING
2. Switch the appliance o and back on again to see if the
fault persists.
IF AFTER THE ABOVE CHECKS THE FAULT STILL
OCCURS, GET IN TOUCH WITH THE NEAREST
AFTERSALES SERVICE
To receive assistance, call the number shown on the warranty
booklet or follow the instructions on the website
website www.hotpoint.eu
When contacting our Client After sales service, always specify:
• a brief description of the fault;
• the type and exact model of the appliance;
xxxxxxxxxxxx
• the service number (number after the word Service on the
rating plate).
• your full address;
• your telephone number.
If any repairs are required, please contact an authorised after-
sales service (to guarantee that original spare parts will be used
and repairs carried out correctly).
1. 2. 3.
4. 5.
150 ml
100 ml
50 ml
10 mm - 0,39 inch
2 cm - 0,7 inch
6. 7.
10. 11.
12.
13. 14.
max 100 cm
39 inch
min 65 cm
25 inch
max 100 cm
39 inch
min 65 cm
25 inch
max 100 cm
39 inch
min 65 cm
25 inch
9.8.
max 0,5 cm
max 0,2 inch
EN
SAFETY INSTRUCTIONS IMPORTANT TO BE READ AND OBSERVE
Before using the appliance, read these safety instruc-
tions. Keep them nearby for future reference. These
instructions and the appliance itself provide impor-
tant safety warnings, to be observed at all times.
The manufacturer declines any liability for failure to
observe these safety instructions, for inappropriate
use of the appliance or incorrect setting of controls.
Very young children (0-3 years) should be kept
away from the appliance. Young children
(3-8years) should be kept away from the
appliance unless continuously supervised.
Children from 8years old and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and knowledge
can use this appliance only if they are supervised
or have been given instructions on safe use and
understand the hazards involved. Children must
not play with the appliance. Cleaning and user
maintenance must not be carried out by children
without supervision. Never open the door forcibly
or use it as a step.
PERMITTED USE
CAUTION: The appliance is not intended to be
operated by means of an external switching
device, such as a timer, or separate remote
controlled system.
This appliance is intended to be used in
household and similar applications such as: sta
kitchen areas in shops, oces and other working
environments; farm houses; by clients in hotels,
motels, bed & breakfast and other residential
environments.
Do not load the machine above the maximum
capacity (kg of dry cloth) indicated in the
programme table.
This appliance is not for professional use. Do
not use the appliance outdoors.
Do not use any solvents (e.g. turpentine,
benzene), detergents containing solvents,
scouring powder, glass or general purpose
cleaners, or ammable uids; do not machine
wash fabrics that have been treated with solvents
or ammable liquids.
Do not dry unwashed items in the tumble
dryer.
Items that have been soiled with substances
such as cooking oil, acetone, alcohol, petrol,
kerosene, spot removers, turpentine, waxes and
wax removers should be washed in hot water with
an extra amount of detergent before being dried
in the tumble dryer.
Items such as foam rubber (latex foam), shower
caps, waterproof textiles, rubber backed articles
and clothes or pillows tted with foam rubber
pads should not be dried in the tumble dryer.
Fabric softeners, or similar products, should be
used as specied by the fabric softener
instructions.
The nal part of a tumble dryer cycle occurs
without heat (cool down cycle) to ensure that the
items are left at a temperature that ensures that
the items will not be damaged.
Never stop a tumble dryer before the end of
the drying cycle unless all items are quickly
removed and spread out so that the heat is
dissipated.
During the drying phase, the door tends to get
quite hot.
Do not use the appliance to dry clothes that
have been washed with ammable solvents (e.g.
trichlorethylene).
Do not use the appliance to dry foam rubber or
similar elastomers.
Make sure that the water tap is turned on
during the drying cycles.
Remove all objects from pockets such as
lighters and matches.
INSTALLATION
The appliance must be handled and installed
by two or more persons- risk of injury. Use
protective gloves to unpack and install- risk of
cuts.
If you want to stack a dryer on top of your
washing machine, rst contact our After-Sales
Service or your specialist dealer to verify whether
this is possible. This is only possible if the dryer is
attached to the washing machine by means of
appropriate stacking kit available through our
After- Sales Service or your specialist dealer.
Move the appliance without lifting it by the
worktop or top lid.
Installation, including water supply (if any) and
electrical connections and repairs must be carried
out by a qualied technician. Do not repair or
replace any part of the appliance unless
specically stated in the user manual. Keep
children away from the installation site. After
unpacking the appliance, make sure that it has not
been damaged during transport. In the event of
problems, contact the dealer or your nearest
After-sales Service. Once installed, packaging
waste (plastic, styrofoam parts etc.) must be
stored out of reach of children- risk of suocation.
The appliance must be disconnected from the
power supply before any installation operation-
risk of electric shock. During installation, make
sure the appliance does not damage the power
cable - risk of re or electric shock. Only activate
the appliance when the installation has been
completed.
859991002850
Do not install your appliance where it may be
exposed to extreme conditions, such as: poor
ventilation, temperatures below 5 °C or above 35 °C.
When installing the appliance make sure that
the four feet are stable and resting on the oor,
adjusting them as required, and check that the
appliance is perfectly to level using a spirit level.
If the appliance is being installed on wood or
“oating” oors (certain parquet and laminate
materials), secure a 60x60x3cm (at least) sheet
of plywood to the oor then place the appliance
on top of this.
Connect the water inlet hose(s) to the water
supply in accordance with the regulations of your
local water company.
For cold ll only models: do not connect to the
hot water supply.
For models with hot ll: the hot water inlet
temperature must not exceed 60°C.
The washing machine is tted with transport
bolts to prevent any possible damage to the
interior during transport. Before using the
machine, it is imperative that the transport bolts
are removed. After their removal, cover the
openings with the 4 enclosed plastic caps.
After installation of the device, wait a few
hours before starting it so that it acclimates to the
environmental conditions of the room.
Make sure that the ventilation openings in the
base of your washing machine (if available on
your model) are not obstructed by a carpet or
other material.
Use only new hoses to connect the appliance
to the water supply. The old hose-sets should not
be reused.
The supply water pressure must be in the 0.1-1
Mpa range.
ELECTRICAL WARNINGS
It must be possible to disconnect the appliance
from the power supply by unplugging it if plug is
accessible, or by a multi-pole switch installed
upstream of the socket in accordance with the
wiring rules and the appliance must be earthed in
conformity with national electrical safety
standards.
Do not use extension leads, multiple sockets or
adapters. The electrical components must not be
accessible to the user after installation. Do not use
the appliance when you are wet or barefoot. Do
not operate this appliance if it has a damaged
power cable or plug, if it is not working properly,
or if it has been damaged or dropped.
If the supply cord is damaged, it must be
replaced with an identical one by the
manufacturer, its service agent or similarly
qualied persons in order to avoid a hazard- risk
of electric shock.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is
switched o and disconnected from the power
supply before performing any maintenance
operation; never use steam cleaning equipment-
risk of electric shock.
DISPOSAL OF PACKAGING MATERIALS
The packaging material is 100% recyclable and is marked with the
recycle symbol .
The various parts of the packaging must therefore be disposed of
responsibly and in full compliance with local authority regulations
governing waste disposal.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufactured with recyclable or reusable materials.
Dispose of it in accordance with local waste disposal regulations.
For further information on the treatment, recovery and recycling
of household electrical appliances, contact your local authority,
the collection service for household waste or the store where you
purchased the appliance. This appliance is marked in compliance
with European Directive 2012/19/EU, Waste Electrical and Electronic
Equipment (WEEE). By ensuring this product is disposed of correctly,
you will help prevent negative consequences for the environment and
human health.
The symbol on the product or on the accompanying documentation
indicates that it should not be treated as domestic waste but must be
taken to an appropriate collection center for the recycling of electrical
and electronic equipment.