Table of Contents
- Product description
- External component identification
- Illustrated parts catalog
- Removal and replacement procedures preliminary requirements
- Removal and replacement procedures for authorized service provider parts
- Using Setup Utility (BIOS)
- Using HP PC Hardware Diagnostics (UEFI)
- Backing up, restoring, and recovering
- Specifications
- Power cord set requirements
- Recycling
- Index
HP 17-w000nd User Manual
Displayed below is the user manual for 17-w000nd by HP which is a product in the Notebooks category. This manual has pages.
Related Manuals
OMEN by HP Laptop PC
Maintenance and Service Guide
IMPORTANT! This document is intended for
HP authorized service providers only.
© Copyright 2016 HP Development Company,
L.P.
NVIDIA and GeForce are trademarks and/or
registered trademarks of NVIDIA Corporation in
the U.S. and other countries. Bluetooth is a
trademark owned by its proprietor and used by
HP Inc. under license. Intel and Core are
trademarks of Intel Corporation in the U.S. and
other countries. Microsoft and Windows are
either registered trademarks or trademarks of
Microsoft Corporation in the United States
and/or other countries.
Product notice
This guide describes features that are common
to most models. Some features may not be
available on your computer.
Not all features are available in all editions or
versions of Windows. Systems may require
upgraded and/or separately purchased
hardware, drivers, software or BIOS update to
take full advantage of Windows functionality.
Windows 10 is automatically updated, which is
always enabled. ISP fees may apply and
additional requirements may apply over time
for updates. Go to http://www.microsoft.com
for details.
The information contained herein is subject to
change without notice. The only warranties for
HP products and services are set forth in the
express warranty statements accompanying
such products and services. Nothing herein
should be construed as constituting an
additional warranty. HP shall not be liable for
technical or editorial errors or omissions
contained herein.
Third Edition: August 2016
First Edition: May 2016
Document Part Number: 861728-003
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the device, do not place the
device directly on your lap or obstruct the device air vents. Use the device only on a hard, at surface. Do not
allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or
clothing, to block airow. Also, do not allow the AC adapter to contact the skin or a soft surface, such as
pillows or rugs or clothing, during operation. The device and the AC adapter comply with the user-accessible
surface temperature limits dened by the International Standard for Safety of Information Technology
Equipment (IEC 60950-1).
iii
iv Safety warning notice
vi Processor information
Table of contents
1 Product description ....................................................................................................................................... 1
2 External component identication .................................................................................................................. 5
Right side ............................................................................................................................................................... 5
Left side ................................................................................................................................................................. 6
Display .................................................................................................................................................................... 7
Top .......................................................................................................................................................................... 8
TouchPad ............................................................................................................................................. 8
Lights ................................................................................................................................................... 9
Button and speakers ......................................................................................................................... 10
Keys ................................................................................................................................................... 11
Using the action keys ........................................................................................................................ 11
Bottom ................................................................................................................................................................. 13
Rear ...................................................................................................................................................................... 14
Labels ................................................................................................................................................................... 14
3 Illustrated parts catalog .............................................................................................................................. 16
Computer major components .............................................................................................................................. 16
Display assembly subcomponents ...................................................................................................................... 19
Miscellaneous parts ............................................................................................................................................. 20
4 Removal and replacement procedures preliminary requirements .................................................................... 22
Tools required ...................................................................................................................................................... 22
Service considerations ......................................................................................................................................... 22
Plastic parts ....................................................................................................................................... 22
Cables and connectors ...................................................................................................................... 23
Drive handling ................................................................................................................................... 23
Grounding guidelines ........................................................................................................................................... 24
Electrostatic discharge damage ........................................................................................................ 24
Packaging and transporting guidelines .......................................................................... 25
Workstation guidelines ................................................................................................... 25
Equipment guidelines ..................................................................................................... 26
5 Removal and replacement procedures for authorized service provider parts .................................................... 27
Component replacement procedures .................................................................................................................. 27
Base enclosure .................................................................................................................................. 27
vii
Battery ............................................................................................................................................... 29
Display assembly ............................................................................................................................... 32
Hard drive .......................................................................................................................................... 34
SSD (M.2) ........................................................................................................................................... 36
Memory .............................................................................................................................................. 37
WLAN module .................................................................................................................................... 39
USB board .......................................................................................................................................... 40
Power button board .......................................................................................................................... 41
Fans ................................................................................................................................................... 42
Heat sink for discrete graphics memory ........................................................................................... 43
Heat sink for CPU and graphics ......................................................................................................... 44
Speakers ............................................................................................................................................ 46
System board .................................................................................................................................... 47
RTC battery ........................................................................................................................................ 49
Power connector ............................................................................................................................... 50
TouchPad ........................................................................................................................................... 52
Display panel ..................................................................................................................................... 54
Camera ............................................................................................................................................... 59
6 Using Setup Utility (BIOS) ............................................................................................................................. 61
Starting Setup Utility (BIOS) ................................................................................................................................ 61
Updating Setup Utility (BIOS) .............................................................................................................................. 61
Determining the BIOS version ........................................................................................................... 61
Downloading a BIOS update .............................................................................................................. 62
7 Using HP PC Hardware Diagnostics (UEFI) ....................................................................................................... 63
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device .................................................................... 63
8 Backing up, restoring, and recovering ........................................................................................................... 65
Creating recovery media and backups ................................................................................................................ 65
Creating HP Recovery media (select products only) ......................................................................... 65
Using Windows tools ........................................................................................................................................... 66
Restore and recovery ........................................................................................................................................... 67
Recovering using HP Recovery Manager ........................................................................................... 67
What you need to know before you get started ............................................................. 67
Using the HP Recovery partition (select products only) ................................................. 68
Using HP Recovery media to recover .............................................................................. 68
Changing the computer boot order ................................................................................ 69
Removing the HP Recovery partition (select products only) ......................................... 70
viii
9 Specications .............................................................................................................................................. 71
Computer specications ...................................................................................................................................... 71
39.62 cm (15.6 in) display specications ............................................................................................................ 72
Hard drive specications ..................................................................................................................................... 72
10 Power cord set requirements ...................................................................................................................... 74
Requirements for all countries ............................................................................................................................ 74
Requirements for specic countries and regions ................................................................................................ 75
11 Recycling .................................................................................................................................................. 77
Index ............................................................................................................................................................. 78
ix
x
1 Product description
Category Description
Product Name OMEN by HP Laptop PC
Processors 6th generation Intel® Core™ i7 Processor
Intel Core i7-6700 HQ (2.6 GHz, turbo up to 3.5 GHz), 2133 MHz/6 MB L3, Quad, TDP 45 W, cTDP 35 W
6th generation Intel Core i5 Processor
Intel Core i5-6300 HQ (2.3 GHz, turbo up to 3.2 GHz), 2133 MHz/6 MB L3, Quad, TDP 45 W, cTDP 35 W
6th generation Intel Core i3 Processor
Intel Core i3-6100H (2.7 GHz, turbo up to 2.7 GHz), 2133 MHz/3 MB L3, Dual, TDP 35 W (not available for
products with Hybrid Green), for use with NVIDIA® N16 P-GT (GeForce® GTX 950 M) only
Chipset Intel HM170
Graphics Internal graphics:
Intel HD Graphics 530
Hybrid graphics:
NVIDIA N16 P-GT (GeForce GTX 950 M) with up to 2048 MB of dedicated video memory (128 Mx32 GDDR5 x 4
PCs) (not available for products with Hybrid Green)
NVIDIA N16 P-GX (GeForce GTX 960 M) with up to 2048 MB of dedicated video memory (128 Mx32 GDDR5 x 4
PCs) (not available to Core-i3)
NVIDIA N16 P-GX (GeForce GTX 960 M) with up to 4096 MB of dedicated video memory (256 Mx32 GDDR5 x 4
PCs) (not available to Core-i3) (not available for products with Hybrid Green)
NVIDIA N16 E-GR (GeForce GTX 965M) with up to 4096 MB of dedicated video memory (256 Mx32 GDDR5 x 4
PCs) (not available to Core-i3)
Support HD Decode, DX12, and HDMI
Support Optimus
Support GPS (GPU Performance Scaling)
Panel 16:9 Ultra Wide Aspect Ratio
15.6" FHD WLED AntiGlare (1920x1080) slim-at (3.2 mm) UWVA, eDP, typical brightness 220 nits
15.6" FHD WLED AntiGlare (1920x1080) slim-at (3.2 mm) UWVA, eDP, typical brightness 250 nits, bridged to
220 nits FHD panel
15.6" UHD Pentile WLED AntiGlare (3840x2160) uslim-at (2.6 mm) UWVA, eDP+PSR, typical brightness 300
nits
Color Back cover:
●Shadow Mesh, Pattern: Shadow Mesh
●Twinkle Black
Top cover with keyboard:
●Black, Pattern: Shadow Mesh + Dragon Red
●Ash Silver background + Hybrid Green pattern gradient, Pattern: Hexagon
1
Category Description
Base enclosure:
●Twinkle Black for products with Dragon Red
●Twinkle Black with Hybrid Green feet for products with Hybrid Green
Memory Two SODIMM slots - customer non-accessible/non-upgradeable
DDR4-2133 Dual Channel Support (DDR4-2400 bridge to DDR4-2133)
Supports up to 16 GB max system memory
4096 MB (4096 MB x 1)
6144 MB (2048 MB x 1 + 4096MB x 1), no support for 32-bit OS
8192 MB (4096 MB x 2), no support for 32-bit OS
8192 MB (8192 MB x 1), no support for 32-bit OS
12288 MB (8192 MB +4096 MB), no support for 32-bit OS and Win7 Home Basic
16384 MB (8192 MB x 2), no support for 32-bit OS and Win7 Home Basic
Hard drive Supports all 7 mm/9.5 mm, SATA 2.5" hard drives
HP 3D DriveGuard
Single hard drive congurations
1 TB (7200) 9.5 mm
2 TB (5400) 9.5 mm
PCIe NVMe TLC M.2 SSD
256 GB
512 GB
Hard drive +SSD congurations
1 TB (7200) 9.5 mm hard drive + 256 GB PCIe NVMe TLC M.2 SSD
1 TB (7200) 9.5 mm hard drive + 128 GB M.2 SATA-3 SSD (Value)
2 TB (5400) 9.5 mm hard drive + 128 GB M.2 SATA-3 SSD (Value)
Optical drive (External
USB)
9.5 mm tray load - SATA - External USB ODD (Aluminum material)
DVD+/-RW Double-Layer SuperMulti
Camera and
Microphone
HP TrueVision HD:
HP Wide Vision HD Camera - indicator LED, USB 2.0, BSI sensor, f2.0, 88° WFOV
720p by 30 frames per second
Dual array Digital Microphones with appropriate software - beam forming, echo cancellation, noise
suppression
Intel RealSense 3D Camera: (not available for products with Hybrid Green)
Intel RealSense 3D camera - indicator LED, USB 3.0, 85° WFOV
1080p by 30 frames per second, 4x depth resolution
Support Windows Hello
Dual array Digital Microphones with appropriate software
Enable HP Noise Cancellation
2 Chapter 1 Product description
Category Description
Support HP Audio Boost
Audio Bang and Olufsen
Dual Speakers
Ethernet Integrated 10/100/1000 NIC
Wireless Integrated Wireless options with dual antennas (M.2/PCIe):
Intel Dual Band Wireless-AC 7265 802.11 ac 2x2 WiFi + BT 4.2 Combo Adapter (non vPRO)
Intel WiDi support (select products only)
Compatible with Miracast-certied devices
External media cards HP Multi-Format Digital Media Card Reader
Support SD/SDHC/SDXC
Push-Push Insertion/Removal
Internal card
expansion
One M.2 slot for WLAN
One M.2 slot for SSD
Ports Hot Plug / Unplug and auto detect for correct output to wide-aspect vs. standard aspect video
(auto adjust panel resolution to t embedded panel and external monitor connected)
Headphone / Microphone Combo Jack
HDMI v2.0 supporting: up to 4096x2160 @ 60Hz
Connect HDMI 2.0 to dGPU
USB 2.0 Ports on Unit:
1 (left side)
USB 3.0 Ports on Unit:
2 (1 on the left side ; 1 on the right side)
RJ-45 / Ethernet
AC Smart Pin adapter plug
Keyboard/pointing
devices
Full Size Backlit 3 Coat paint island-style keyboard with numeric key pad Dragon Red
Full Size Backlit 3 Coat paint island-style keyboard with numeric key pad Hybrid Green
TouchPad Requirements:
Clickpad with image sensor
Multitouch gestures enabled
Support Modern Trackpad Gestures
Taps enabled as default
Power requirements Batteries:
3 cell prismatic battery - 61.5 Whr (5360 mAh)
Battery life enhancement
Supports battery fast charge; when the battery charge remaining is between zero and 90%, the battery will
charge to 90% of full capacity in no more than 90 minutes
AC Adapters:
3
Category Description
●120 W
●150 W, for use with products with NVIDIA N16 E-GR only
●1 M length power cord
Mechanical
Requirements
Chassis Buttons
Power
LED indicators
Security TPM 2.0
Kensington Security Lock
Operating system Preinstalled:
Windows 10
Windows 10 Pro
For Developed Market (ML):
Windows 10 Home ML
Windows 10 Home High End ML (for use with Intel Core i7-6700 HQ with > 4 GB, or, any processor with
≥1080p screen and ≥ 8GB)
For Emerging Market (EM/SL):
Windows 10 Home EM/SL
Windows 10 Home High End EM/SL (for use with Intel Core i7-6700 HQ with > 4 GB, or, any processor with
≥1080p screen and ≥ 8GB)
CPPP Windows 10 Home China Language Edition
CPPP Windows 10 Home High End China Language Edition (for use with Intel Core i7-6700 HQ with > 4 GB, or,
any processor with ≥1080p screen and ≥ 8GB)
SEAP Windows 10 Home Single Language Edition (select products only)
SEAP Windows 10 Home High End (select products only)
Serviceability End user replaceable parts:
AC adapter
4 Chapter 1 Product description
2 External component identication
Right side
Description
(1) Memory card reader Reads optional memory cards that enable you to store,
manage, share, or access information.
To insert a card:
1. Hold the card label-side up, with connectors facing the
computer.
2. Insert the card into the memory card reader, and then
press in on the card until it is rmly seated.
To remove a card:
▲Press in on the card, and then remove it from the
memory card reader.
(2) Drive light (select products only) ●Blinking white: The hard drive is being accessed.
●Amber: HP 3D DriveGuard has temporarily parked the
hard drive (select products only).
(3) USB 3.0 port Connects an optional USB device, such as a keyboard, mouse,
external drive, printer, scanner, or USB hub.
(4) HDMI port Connects an optional video or audio device, such as a high-
denition television, any compatible digital or audio
component, or a high-speed High Denition Multimedia
Interface (HDMI) device.
(5) RJ-45 (network) jack/status lights Connects a network cable.
●White: The network is connected.
●Amber: Activity is occurring on the network.
(6) Power connector Connects an AC adapter.
(7) AC adapter and battery light ●White: The AC adapter is connected and the battery is
fully charged.
●Blinking white: The AC adapter is disconnected and the
battery has reached a low battery level.
Right side 5
Description
●Amber: The AC adapter is connected and the battery is
charging.
●O: The battery is not charging.
Left side
Description
(1) Security cable slot Attaches an optional security cable to the computer.
NOTE: The security cable is designed to act as a deterrent,
but it may not prevent the computer from being mishandled or
stolen.
(2) USB 2.0 port Connects an optional USB device, such as a keyboard, mouse,
external drive, printer, scanner, or USB hub.
(3) USB 3.0 port Connects an optional USB device, such as a keyboard, mouse,
external drive, printer, scanner, or USB hub.
(4) Audio-out (headphone)/Audio-in (microphone)
combo jack
Connects optional powered stereo speakers, headphones,
earbuds, a headset, or a television audio cable. Also connects
an optional headset microphone. This jack does not support
optional standalone microphones.
WARNING! To reduce the risk of personal injury, adjust the
volume before putting on headphones, earbuds, or a headset.
For additional safety information, refer to the Regulatory,
Safety, and Environmental Notices.
To access this guide:
▲Select the Start button, select All apps (required on
some products), select HP Help and Support, and then
select HP Documentation.
NOTE: When a device is connected to the jack, the computer
speakers are disabled.
6 Chapter 2 External component identication
Display
NOTE: Refer to the illustration that most closely matches your computer.
Component Description
(1) Internal microphones Record sound.
(2) Camera light On: The camera is in use.
(3) Camera Allows you to video chat, record video, or record still images. Some
also provide HD (high-denition) or 3D capability, apps for gaming,
or facial recognition software like Windows Hello.
To use your camera:
●Type camera in the taskbar search box, and then select
Camera.
●On select products, type Intel RealSense in the taskbar search
box to explore additional features, demos, and apps.
(4) WLAN antennas* Send and receive wireless signals to communicate with wireless local
area networks (WLANs).
*The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around the
antennas free from obstructions.
For wireless regulatory notices, see the section of the Regulatory, Safety, and Environmental Notices that applies to your country or
region.
To access this guide:
▲Select the Start button, select All apps (required on some products), select HP Help and Support, and then select HP
Documentation.
Display 7
Top
TouchPad
Component Description
(1) TouchPad zone Reads your nger gestures to move the pointer or activate items
on the screen.
(2) Left TouchPad button Functions like the left button on an external mouse.
(3) Right TouchPad button Functions like the right button on an external mouse.
8 Chapter 2 External component identication
Lights
Component Description
(1) Power light ●On: The computer is on.
●Blinking: The computer is in the Sleep state, a power-
saving state. The computer shuts o power to the display
and other unneeded components.
●O: The computer is o or in Hibernation. Hibernation is a
power-saving state that uses the least amount of power.
(2) Caps lock light On: Caps lock is on, which switches the key input to all capital
letters.
(3) Mute light ●Amber: Computer sound is o.
●O: Computer sound is on.
Top 9
Button and speakers
Component Description
(1) Power button ●When the computer is o, press the button to turn on the
computer.
●When the computer is on, press the button briey to
initiate Sleep.
●When the computer is in the Sleep state, press the button
briey to exit Sleep.
●When the computer is in Hibernation, press the button
briey to exit Hibernation.
CAUTION: Pressing and holding down the power button results
in the loss of unsaved information.
If the computer has stopped responding and shutdown
procedures are ineective, press and hold the power button
down for at least 5 seconds to turn o the computer.
To learn more about your power settings, see your power
options.
▲Type power in the taskbar search box, and then select
Power and sleep settings.
‒ or –
Right-click the Start button, and then select Power
Options.
(2) Speakers Produce sound.
10 Chapter 2 External component identication
Keys
Component Description
(1) esc key Displays system information when pressed in combination with
the fn key.
(2) fn key Executes frequently used system functions when pressed in
combination with the esc key, action keys, or the spacebar.
(3) Windows key Opens the Start menu.
NOTE: Pressing the Windows key again will close the Start
menu.
(4) num lock key Alternates between the navigational and numeric functions on
the integrated numeric keypad.
(5) Integrated numeric keypad When num lock is on, the keypad can be used like an external
numeric keypad.
Using the action keys
●An action key performs an assigned function.
●The icon on each action key illustrates the function for that key.
●To use an action key, press and hold the key.
Icon Description
Decreases the screen brightness incrementally as long as you hold down the key.
Increases the screen brightness incrementally as long as you hold down the key.
Switches the screen image between display devices connected to the system. For example, if a monitor is
connected to the computer, repeatedly pressing this key alternates the screen image from the computer
display to the monitor display to a simultaneous display on both the computer and the monitor.
Turns the keyboard backlight o or on.
NOTE: To conserve battery power, turn o this feature.
Top 11
Icon Description
Mutes or restores speaker sound.
Decreases speaker volume incrementally while you hold down the key.
Increases speaker volume incrementally while you hold down the key.
Plays the previous track of an audio CD or the previous section of a DVD or a Blu-ray Disc (BD).
Starts, pauses, or resumes playback of an audio CD, a DVD, or a BD.
Plays the next track of an audio CD or the next section of a DVD or a BD.
Turns the airplane mode and wireless feature on or o.
NOTE: The airplane mode key is also referred to as the wireless button.
NOTE: A wireless network must be set up before a wireless connection is possible.
12 Chapter 2 External component identication
Bottom
Description
Vents (2) Enable airow to cool internal components.
NOTE: The computer fan starts up automatically to cool internal
components and prevent overheating. It is normal for the internal fan to
cycle on and o during routine operation.
Bottom 13
Rear
Description
Vent Enables airow to cool internal components.
NOTE: The computer fan starts up automatically to cool internal
components and prevent overheating. It is normal for the internal
fan to cycle on and o during routine operation.
Labels
The labels axed to the computer provide information you may need when you troubleshoot system
problems or travel internationally with the computer.
IMPORTANT: Check the following locations for the labels described in this section: the bottom of the
computer, inside the battery bay, under the service door, or on the back of the display.
●Service label—Provides important information to identify your computer. When contacting support, you
will probably be asked for the serial number, and possibly for the product number or the model number.
Locate these numbers before you contact support.
Your service label will resemble one of the examples shown below. Refer to the illustration that most
closely matches the service label on your computer.
Component
(1) Serial number
(2) Product number
(3) Warranty period
(4) Model number (select products only)
14 Chapter 2 External component identication
Component
(1) Model name (select products only)
(2) Product number
(3) Serial number
(4) Warranty period
●Regulatory label(s)—Provide(s) regulatory information about the computer.
●Wireless certication label(s)—Provide(s) information about optional wireless devices and the approval
markings for the countries or regions in which the devices have been approved for use.
Labels 15
3 Illustrated parts catalog
Computer major components
NOTE: HP continually improves and changes product parts. For complete and current information on
supported parts for your computer, go to http://partsurfer.hp.com, select your country or region, and then
follow the on-screen instructions.
NOTE: Details about your computer, including model, serial number, product key, and length of warranty,
are on the service tag at the bottom of your computer. See Labels on page 14 for details.
16 Chapter 3 Illustrated parts catalog
Item Component Spare part number
(1) Display panel (see Display assembly on page 32)
(2) Top cover with TouchPad and keyboard (see TouchPad on page 52 for a detailed list of country codes)
(3) TouchPad board 860364-001
TouchPad cable 858967-001
(4) Speaker Kit 858976-001
(5) USB board cable 856729-001
(6) RTC battery 741976-001
Computer major components 17
Item Component Spare part number
(7) Power connector (includes cable) 858021-001
(8) Power button board 858974-001
Power button board cable 858966-001
(9) Solid-state drive
Generic SSD 128 GB 2280 M2 SATA-3 Value TL 827560-027
Generic SSD 256 GB 2280 M2 PCIe 3x4SS NVMeTLC TL 847109-008
Generic SSD 512 GB 2280 M2PCIe 3x4SS NVMeTLC TL 847110-007
(10) System board (see System board on page 47)
(11) Memory
4 GB 2133 MHz 1.2v DDR4 shared 820569-005
8 GB 2133 MHz 1.2v DDR4 shared 820570-005
2 GB 2133 MHz 1.2v DDR4 shared 851379-005
(12) WLAN module, Intel Dual Band Wireless-AC 7265 793840-005
(13) Heat sink for products with discrete graphics 856668-001
(14) Heat sink for CPU and graphics 725625-001
(15) USB board 858975-001
(16) Hard drive
1 TB 7200 RPM SATA RAW 9.5mm 766644-005
2 TB 5400 RPM SATA RAW 9.5 mm 801808-005
Hard drive cable 858969-001
(17) Hard drive brackets not spared
(18) Battery cable 858968-001
(19) Fan, the same spare part number can be used to replace either the right fan or the left fan 858970-001
(20) Battery 849910-850
(21) Base enclosure
Twinkle Black for Shadow Mesh nish 858965-001
Twinkle Black with Hybrid Green feet 905114-001
18 Chapter 3 Illustrated parts catalog
Display assembly subcomponents
Item Component Spare part number
(1) Bezel
For products with an HD camera 856725-001
For products with a 3D camera 856726-001
(2) Camera
Intel RealSense 3D camera 1p NM U3 1080p 781624-005
HP Wide Vision HD camera 1p DM U2 Mjpeg 720p VDH SF HD 846006-003
3D camera cable 859445-001
(3) Raw panel
15.6" generic panel, FHD AG UWVA 220 eDP, Slim KR 752920-014
Display assembly subcomponents 19
Item Component Spare part number
15.6" generic panel, UHD AG UWVA300 eDPU Slim PSRKR 842484-004
(4) Hinge assembly 856741-001
(5) Hinge cap assembly 859737-001
(6) WLAN antenna 856923-001
(7) Display cable
Full high-denition display cable for products with an HD camera 856733-001
Full high-denition display cable for products with a 3D camera 856734-001
High-denition display cable for products with an HD camera 856735-001
High-denition display cable for products with a 3D camera 856736-001
(8) Back cover
In Hybrid Green nish, with antenna 905115-001
In Shadow Mesh nish, with antenna, for products with an HD camera 856715-001
In Shadow Mesh nish, with antenna, for products with a 3D camera 856718-001
Miscellaneous parts
Component Spare part number
AC adapter 120 W adapter PFC S-3P, slim, 4.5 mm 710415-001
AC adapter 150 W adapter PFC smart, slim,4.5 mm (for use with products with NVIDIA N16 E-GR only) 776620-001
HP HDMI to VGA adapter 701943-001
Microphone board 857471-001
HP USB External DVD/RW Drive 747080-001
Power cord
For use in Australia 213356-008
For use in Denmark 213353-008
For use in Europe 213350-009
For use in India 404827-003
For use in Israel 398063-003
For use in Italy 213352-008
For use in Japan 349756-002
For use in Korea 267836-008
For use in North America 213349-009
For use in the People’s Republic of China 286497-008
For use in South Africa 361240-002
20 Chapter 3 Illustrated parts catalog
Component Spare part number
For use in Switzerland 213354-008
For use in Taiwan 393313-003
For use in Thailand 285096-006
For use in the United Kingdom 213351-008
Screw Kit 856752-001
Miscellaneous parts 21
4 Removal and replacement procedures
preliminary requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
●Flat-bladed screwdriver
●Magnetic screwdriver
●Phillips P0 and P1 screwdrivers
Service considerations
The following sections include some of the considerations that you must keep in mind during disassembly
and assembly procedures.
NOTE: As you remove each subassembly from the computer, place the subassembly (and all accompanying
screws) away from the work area to prevent damage.
Plastic parts
CAUTION: Using excessive force during disassembly and reassembly can damage plastic parts. Use care
when handling the plastic
22 Chapter 4 Removal and replacement procedures preliminary requirements
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations during the
reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat
the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid
bending, twisting, or tearing cables. Be sure that cables are routed in such a way that they cannot be caught
or snagged by parts being removed or replaced. Handle ex cables with extreme care; these cables tear
easily.
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the
computer, damage to a drive, or loss of information, observe these precautions:
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer is
o or in Hibernation, turn the computer on, and then shut it down through the operating system.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive, avoid
touching the connector.
Before removing an optical drive, be sure that a disc is not in the drive and be sure that the optical drive tray is
closed.
Handle drives on surfaces covered with at least one inch of shock-proof foam.
Avoid dropping drives from any height onto any surface.
After removing a hard drive or an optical drive, place it in a static-proof bag.
Avoid exposing an internal hard drive to products that have magnetic elds, such as monitors or speakers.
Avoid exposing a drive to temperature extremes or liquids.
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective
packaging and label the package “FRAGILE.”
Service considerations 23
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine
the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many
cases, ESD contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a nger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be aected at all and can work perfectly throughout a normal
cycle. Or the device may function normally for a while, then degrade in the internal layers, reducing its life
expectancy.
CAUTION: To prevent damage to the computer when you are removing or installing internal components,
observe these precautions:
Keep components in their electrostatic-safe containers until you are ready to install them.
Before touching an electronic component, discharge static electricity by using the guidelines described in this
section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity aects the electrostatic voltage levels generated by dierent
activities.
CAUTION: A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event 10% 40% 55%
Walking across carpet 35,000 V 15,000 V 7,500 V
Walking across vinyl oor 12,000 V 5,000 V 3,000 V
Motions of bench worker 6,000 V 800 V 400 V
Removing DIPS from plastic tube 2,000 V 700 V 400 V
Removing DIPS from vinyl tray 11,500 V 4,000 V 2,000 V
Removing DIPS from plastic foam 14,500 V 5,000 V 3,500 V
Removing bubble pack from PCB 26,500 V 20,000 V 7,000 V
Packing PCBs in foam-lined box 21,000 V 11,000 V 5,000 V
24 Chapter 4 Removal and replacement procedures preliminary requirements
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
●To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
●Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
●Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
●Place items on a grounded surface before removing items from their containers.
●Always be properly grounded when touching a component or assembly.
●Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive foam.
●Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that mechanized
equipment used for moving materials is wired to ground and that proper materials are selected to avoid
static charging. When grounding is not possible, use an ionizer to dissipate electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
●Cover the workstation with approved static-shielding material.
●Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and
equipment.
●Use conductive eld service tools, such as cutters, screwdrivers, and vacuums.
●When xtures must directly contact dissipative surfaces, use xtures made only of static safe materials.
●Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and plastic
foam.
●Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle these
items only at static-free workstations.
●Avoid contact with pins, leads, or circuitry.
●Turn o power and input signals before inserting or removing connectors or test equipment.
Grounding guidelines 25
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
●When seated, wear a wrist strap connected to a grounded system. Wrist straps are exible straps with a
minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap
snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips
to connect a wrist strap.
●When standing, use foot straps and a grounded oor mat. Foot straps (heel, toe, or boot straps) can be
used at standing workstations and are compatible with most types of shoes or boots. On conductive
oors or dissipative oor mats, use foot straps on both feet with a minimum of one megohm resistance
between the operator and ground. To be eective, the conductive equipment must be worn in contact
with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
●Antistatic tape
●Antistatic smocks, aprons, and sleeve protectors
●Conductive bins and other assembly or soldering aids
●Nonconductive foam
●Conductive tabletop workstations with ground cords of one megohm resistance
●Static-dissipative tables or oor mats with hard ties to the ground
●Field service kits
●Static awareness labels
●Material-handling packages
●Nonconductive plastic bags, tubes, or boxes
●Metal tote boxes
●Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and oor mats.
Material Use Voltage protection level
Antistatic plastics Bags 1,500 V
Carbon-loaded plastic Floor mats 7,500 V
Metallized laminate Floor mats 5,000 V
26 Chapter 4 Removal and replacement procedures preliminary requirements
5 Removal and replacement procedures for
authorized service provider parts
CAUTION: Components described in this chapter should be accessed only by an authorized service provider.
Accessing these parts can damage the computer or void the warranty.
CAUTION: This computer does not have user-replaceable parts. Only HP authorized service providers should
perform the removal and replacement procedures described here. Accessing the internal part could damage
the computer or void the warranty.
Component replacement procedures
NOTE: Details about your computer, including model, serial number, product key, and length of warranty,
are on the service tag at the bottom of your computer. See Labels on page 14 for details.
NOTE: HP continually improves and changes product parts. For complete and current information on
supported parts for your computer, go to http://partsurfer.hp.com, select your country or region, and then
follow the on-screen instructions.
There are as many as 61 screws that must be removed, replaced, and/or loosened when servicing the parts
described in this chapter. Make special note of each screw size and location during removal and replacement.
Base enclosure
Description Spare part number
Twinkle Black for Shadow Mesh nish 858965-001
Twinkle Black with Hybrid Green feet 905114-001
Before disassembling the computer, follow these steps:
1. Turn o the computer. If you are unsure whether the computer is o or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
Remove the base enclosure:
1. Position the computer upside down on a at surface.
Component replacement procedures 27
2. Remove the plastic plug and screw (1), and then remove the 2 Phillips M2x5.0 screws (2) and the 8
M2.5x6.0 screws (3).
NOTE: There are three internal clips by the battery area. Carefully disengage those clips as you are
removing the base enclosure.
3. Slide a nylon ake tool around the edge of the base enclosure to loosen it, taking care not to damage
the internal clips. Lift the front edge (1) to access the internal clips in the battery area.
4. Remove the base enclosure (2).
28 Chapter 5 Removal and replacement procedures for authorized service provider parts
Battery
Description Spare part number
Battery 3C 61WH 5.37Ah LI TE03061XL-PR 849910-850
Battery cable 858968-001
Remove the battery:
WARNING! To reduce potential safety issues, use only the user-replaceable battery provided with the
computer, a replacement battery provided by HP, or a compatible battery purchased from HP.
CAUTION: Removing a user-replaceable battery that is the sole power source for the computer can cause
loss of information. To prevent loss of information, save your work or shut down the computer through
Windows before removing the battery.
Before removing the battery, follow these steps:
1. Shut down the computer.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
Remove the battery:
1. Disconnect the battery cable from the battery.
Component replacement procedures 29
2. Disconnect the battery cable from the system board (1), release the battery cable from the routing
channels (2), and then lift the battery cable to remove it (3).
30 Chapter 5 Removal and replacement procedures for authorized service provider parts
3. Remove 4 Phillips 2x5 screws (1), lift the battery (2), and then slide the battery (3) to remove it from the
computer.
To insert the battery, reverse the removal procedures.
Component replacement procedures 31
Display assembly
IMPORTANT: Make special note of each screw and screw lock size and location during removal
and replacement.
Before removing the display assembly, follow these steps:
1. Shut down the computer.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
5. Disconnect the battery (see Battery on page 29).
Remove the display assembly:
1. Remove 3 Phillips 2.5x6.0 screws from the left hinge and 3 Phillips 2.5x6.0 screws from the right hinge
bracket (1), and then lift the hinge brackets (2) to remove them .
32 Chapter 5 Removal and replacement procedures for authorized service provider parts
2. Disconnect the WLAN antenna cable (1), and remove the tape (2) holding it in place, disconnect the
display cable (3), and then release the cable from the routing channels (4).
3. Rotate the display assembly (1), and then remove the display assembly (2) from the base enclosure.
NOTE: For display panel and display component removal procedures, see Display panel on page 54.
Reverse this procedure to install the display assembly.
Component replacement procedures 33
Hard drive
Description Spare part number
Hard drive
1 TB 7200 RPM SATA RAW 9.5mm 766644-005
2 TB 5400 RPM SATA RAW 9.5 mm 801808-005
Hard drive cable 858969-001
IMPORTANT: Make special note of each screw and screw lock size and location during removal
and replacement.
Before removing the hard drive, follow these steps:
1. Shut down the computer.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
5. Disconnect the battery (see Battery on page 29).
Remove the hard drive:
1. Disconnect the hard drive cable (1), slide the hard drive horizontally (2), and then loosen the side
brackets (3).
2. Lift the right side of the hard drive (4), and then remove the hard drive (5).
Reverse this procedure to install the hard drive.
34 Chapter 5 Removal and replacement procedures for authorized service provider parts
If it is necessary to disassemble the hard drive, follow these steps:
▲Remove the hard drive connector (1), and then remove the side brackets (2).
Reverse this procedure to reassemble the hard drive.
Component replacement procedures 35
SSD (M.2)
Description Spare part number
Generic SSD 128 GB 2280 M2 SATA-3 Value TL 827560-027
Generic SSD 256 GB 2280 M2 PCIe 3x4SS NVMeTLC TL 847109-008
Generic SSD 512 GB 2280 M2PCIe3x4SS NVMeTLC TL 847110-007
Before removing the SSD, follow these steps:
1. Turn o the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
5. Disconnect the battery (see Battery on page 29).
Remove the SSD:
1. Remove the Phillips M2.0 x 2.5 screw (1) that secures the SSD to the system board.
2. Remove the SSD (2) by pulling the drive away from the slot at an angle.
Reverse this procedure to install the SSD.
36 Chapter 5 Removal and replacement procedures for authorized service provider parts
Memory
Description Spare part number
Memory
4 GB 2133 MHz 1.2v DDR4 shared 820569-005
8 GB 2133 MHz 1.2v DDR4 shared 820570-005
2 GB 2133 MHz 1.2v DDR4 shared 851379-005
IMPORTANT: Make special note of each screw and screw lock size and location during removal
and replacement.
Before removing the memory, follow these steps:
Update BIOS before adding memory modules
Before adding new memory, make sure you update the computer to the latest BIOS.
CAUTION: Failure to update the computer to the latest BIOS prior to installing new memory may result in
various system problems.
To update BIOS:
1. Navigate to http:\\www.hp.com.
2. Select Support > Support & drivers.
3. In the Enter my HP model number box, type the computer model information, and then select Find my
product.
-or-
Select Identify now.
4. Select the link for the computer model.
5. Select the language and the operating system.
6. Under the downloads heading, select the BIOS link.
7. Select the link for the most recent BIOS.
8. Select the Download button, and then follow the on-screen instructions.
1. Shut down the computer.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
5. Disconnect the battery (see Battery on page 29).
If you are replacing a memory module, remove the existing memory module:
Component replacement procedures 37
1. Lift the clear lm covering the memory module.
2. Pull away the retention clips (1) on each side of the memory module.
The memory module tilts up.
3. Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory
module slot.
CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do
not touch the components on the memory module.
To protect a memory module after removal, place it in an electrostatic-safe container.
Reverse this procedure to install a memory module.
38 Chapter 5 Removal and replacement procedures for authorized service provider parts
WLAN module
Description Spare part number
WLAN module, Intel Dual Band Wireless-AC 7265 793840-005
IMPORTANT: Make special note of each screw and screw lock size and location during removal
and replacement.
Before removing the WLAN module, follow these steps:
1. Shut down the computer.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
5. Disconnect the battery (see Battery on page 29).
Remove the WLAN module:
1. Carefully disconnect 2 antenna cables (1).
2. Remove 1 Phillips 2.0x2.5 screw (2), and then remove the WLAN module (3).
Reverse this procedure to install the WLAN module.
Component replacement procedures 39
USB board
Description Spare part number
USB board 858975-001
USB board cable 856729-001
IMPORTANT: Make special note of each screw and screw lock size and location during removal
and replacement.
Before removing the USB board, follow these steps:
1. Shut down the computer.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
5. Disconnect the battery (see Battery on page 29).
Remove the USB board:
▲Disconnect the zero-insertion force (ZIF) connector (1), remove the USB board cable (2), disconnect 2
zero-insertion force (ZIF) connectors (3) and (4), remove 1 Phillips screw (5), and then lift the USB board
to remove it (6).
Reverse this procedure to install the USB board.
40 Chapter 5 Removal and replacement procedures for authorized service provider parts
Power button board
Description Spare part number
Power button board 858974-001
Power button board cable 858966-001
IMPORTANT: Make special note of each screw and screw lock size and location during removal
and replacement.
Before removing the power button board, follow these steps:
1. Shut down the computer.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
5. Disconnect the battery (see Battery on page 29), and then remove the following components:
a. Display assembly (see Display assembly on page 32).
b. Hard drive (see Hard drive on page 34).
c. USB board (see USB board on page 40).
Remove the power button board:
1. Remove the Phillips screw (1) securing the power button board.
2. Lift the power button board (2) at an angle, and then remove the board (3).
Reverse this procedure to install the power button board.
Component replacement procedures 41
Fans
Description Spare part number
Fan, the same spare part number can be used to replace either the right fan or the left fan 858970-001
IMPORTANT: Make special note of each screw and screw lock size and location during removal
and replacement.
Before removing the fan, follow these steps:
1. Shut down the computer.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
5. Disconnect the battery (see Battery on page 29).
Remove the fans:
1. Disconnect the fan cables (1), and then release the cable from the threading channels (2).
2. Remove the 4 Phillips 2x5 screws (3) from the fans, lift and remove the right fan (4), and then lift and
remove the left fan (5).
Reverse this procedure to install the fans.
42 Chapter 5 Removal and replacement procedures for authorized service provider parts
Heat sink for discrete graphics memory
Description Spare part number
Heat sink for discrete graphics memory 856668-001
Before removing the heat sink for discrete graphics memory, follow these steps:
1. Turn o the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
5. Disconnect the battery (see Battery on page 29).
Remove the heat sink for discrete graphics memory:
1. Remove the 6 Phillips M2.0 screws (1) securing the heat sink.
2. Carefully lift the heat sink (2) to remove it from the system board.
Component replacement procedures 43
3. The following illustration shows the replacement thermal material locations. The thermal material must
be thoroughly cleaned from the surfaces of the heat sink and the system board components each time
the heat sink is removed. Replacement thermal material is included with the heat sink and system board
spare part kits.
Thermal paste is used on the system board components (1), (3) and on the heat sink areas (2), (4) that
service them.
Reverse this procedure to install the heat sink for discrete graphics memory.
Heat sink for CPU and graphics
Description Spare part number
Heat sink for CPU and graphics 725625-001
Before removing the heat sink for CPU and graphics, follow these steps:
1. Turn o the computer. If you are unsure whether the computer is o or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
5. Disconnect the battery (see Battery on page 29).
Remove the heat sink for CPU and graphics:
1. Remove the 2 Phillips screws (1), and then remove the heat sink (2) from the system board.
44 Chapter 5 Removal and replacement procedures for authorized service provider parts
2. The following illustration shows the replacement thermal material locations. The thermal material must
be thoroughly cleaned from the surfaces of the heat sink and the system board components each time
the heat sink is removed. Replacement thermal material is included with the heat sink and system board
spare part kits.
Thermal paste is used on the system board components (1) and on the heat sink areas (2) that service
them.
Reverse this procedure to install the heat sink for CPU and graphics.
Component replacement procedures 45
Speakers
Description Spare part number
Speaker Kit, includes the cable 858976-001
IMPORTANT: Make special note of each screw and screw lock size and location during removal
and replacement.
Before removing the speakers, follow these steps:
1. Shut down the computer.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
5. Disconnect the battery (see Battery on page 29), and then remove the following components:
a. Fans (see Fans on page 42).
b. Heatsink (see Heat sink for discrete graphics memory on page 43).
Remove the speakers:
1. Disconnect the right speaker cable (1).
2. Lift the left speaker and the right speaker, and then remove them (2) .
Reverse this procedure to install the speakers.
46 Chapter 5 Removal and replacement procedures for authorized service provider parts
System board
Description Spare part number
System board
Intel i7-6700HQ system board, 950M, 2 GB, with a Windows operating system 856673-601
Intel 2GB i5-6300HQ system board, 950M, 2 GB, with a Windows operating system 856674-601
Intel i3-6100H system board, 950M, 2 GB, with a Windows operating system 856675-601
Intel i7-6700HQ system board, 960M, 2 GB, with a Windows operating system 856676-601
Intel i5-6300HQ system board, 960M, 2 GB, with a Windows operating system 856677-601
Intel i7-6700HQ system board, 960M, 2 GB, with a Windows operating system 856678-601
Intel i5-6300HQ system board, 960M, 2 GB, with a Windows operating system 856679-601
Intel i7-6700HQ system board, 965M, 4 GB, with a Windows operating system 859750-601
Intel i5-6300HQ system board, 965M, 4 GB, with a Windows operating system 859751-601
IMPORTANT: Make special note of each screw and screw lock size and location during removal
and replacement.
Before removing the system board, follow these steps:
1. Shut down the computer.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
5. Remove the battery (see Battery on page 29), and then remove the following components:
a. Hard drive (see Hard drive on page 34).
b. SSD (see SSD (M.2) on page 36).
c. Fans (see Fans on page 42).
NOTE: When replacing the system board, be sure that the following components are removed from the
defective system board and installed on the replacement system board:
●Heat sink for discrete graphics (see Heat sink for discrete graphics memory on page 43).
●Heat sink for CPU and graphics (see Heat sink for CPU and graphics on page 44).
●WLAN module (see WLAN module on page 39)
●Memory module (see Memory on page 37)
●RTC battery (see RTC battery on page 49)
Remove the system board:
1. Disconnect the following cables and zero-insertion force (ZIF) connectors from the system board:
Component replacement procedures 47
●Wireless antenna cable (1)
●Speaker cable (2)
●Keyboard cable (3)
●Display cable (4)
●USB board cable (5)
●TouchPad cable (6)
●Memory cable (7)
48 Chapter 5 Removal and replacement procedures for authorized service provider parts
2. Remove 1 Phillips 2x5 screw (1), lift the system board (2), and then remove it (3).
Reverse this procedure to install the system board.
RTC battery
Description Spare part number
RTC battery 741976-001
IMPORTANT: Make special note of each screw and screw lock size and location during removal
and replacement.
Before removing the RTC battery, follow these steps:
1. Shut down the computer.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
5. Remove the battery (see Battery on page 29), and then remove the following components:
a. Hard drive (see Hard drive on page 34).
b. SSD (see SSD (M.2) on page 36).
c. Fans (see Fans on page 42).
d. System board (see System board on page 47).
Remove the RTC battery:
Component replacement procedures 49
1. Carefully place the system board face down.
2. Insert a thin plastic tool (1) to lift the RTC battery, and then remove the battery (2).
Reverse this procedure to install the RTC battery.
Power connector
Description Spare part number
Power connector (includes cable) 858021-001
IMPORTANT: Make special note of each screw and screw lock size and location during removal
and replacement.
Before removing the power connector, follow these steps:
1. Shut down the computer.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
5. Remove the battery (see Battery on page 29), and then remove the following components:
a. Hard drive (see Hard drive on page 34).
b. SSD (see SSD (M.2) on page 36).
c. Fans (see Fans on page 42).
d. System board (see System board on page 47).
50 Chapter 5 Removal and replacement procedures for authorized service provider parts
Remove the power connector:
1. Carefully place the system board face down.
2. Disconnect the connector cable, and then remove the power connector.
Reverse this procedure to install the power connector.
Component replacement procedures 51
TouchPad
Description Spare part number
TouchPad board
●Shadow Mesh 860364-001
●Hybrid Green 860330-001
TouchPad cable 858967-001
Top cover with TouchPad in Black with Hybrid Green, and Backlit Keyboard for use in Mainland China 859735-AB1
Top cover with TouchPad in Black with Shadow Mesh, and Backlit Keyboard in Dragon Red 859735–XXX
For use in country
or region
Spare part
number
For use in country
or region
Spare part
number
For use in country
or region
Spare part
number
Belgium -A41 Israel -BB1 Slovenia -BA1
Bulgaria -261 Italy -061 Spain -071
Canada -DB1 Japan -291 Switzerland -BG1
Czech Republic
and Slovakia
-FL1 Korea -AD1
Denmark, Norway,
Finland, and Sweden
-DH1 Latin America -161 Thailand -281
France -051 The Netherlands -B31 Turkey -141
Germany -041 Portugal -131 United Kingdom -031
Greece -151 Romania -271 United States -001
Hungary -211 Russia -251
India -002 Saudi Arabia -171
IMPORTANT: Make special note of each screw and screw lock size and location during removal
and replacement.
Before removing the TouchPad, follow these steps:
1. Shut down the computer.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
5. Remove the battery (see Battery on page 29).
Remove the TouchPad:
1. Remove the 3 Phillips 2.0x2.0 screws (1), and then lift the TouchPad bracket (2) to remove it.
52 Chapter 5 Removal and replacement procedures for authorized service provider parts
2. Disconnect the TouchPad cable (1).
3. Remove the 3 Phillips 2.0x2.5 screws (2).
4. Lift the front of the TouchPad (3), and then slide the TouchPad (4) forward to remove it.
Reverse this procedure to install the TouchPad.
Component replacement procedures 53
Display panel
Description Spare part number
Bezel
For products with an HD camera 856725-001
For products with a 3D camera 856726-001
Display panel
15.6" FHD AG UWVA 220 eDP, Slim KR 752920-014
15.6" UHD AG UWVA300 eDPU Slim PSRKR 842484-004
Hinge assembly 856741-001
Hinge cap assembly 859737-001
Display cable
Full high-denition display cable for products with an HD camera 856733-001
Full high-denition display cable for products with a 3D camera 856734-001
High-denition display cable for products with an HD camera 856735-001
High-denition display cable for products with a 3D camera 856736-001
WLAN antenna cable 856923-001
Back cover
In Hybrid Green nish, with antenna 905115-001
In Shadow Mesh nish, with antenna, for products with HD camera 856715-001
In Shadow Mesh nish, with antenna, for products with 3D camera 856718-001
IMPORTANT: Make special note of each screw and screw lock size and location during removal
and replacement.
Before removing the display assembly, follow these steps:
1. Shut down the computer.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
5. Disconnect the battery (see Battery on page 29), and then remove the following components:
▲Display assembly (see Display assembly on page 32).
Remove the display panel:
1. Use a thin plastic tool to disengage the bezel starting on the top edge (1). Continue on the left and right
edges (2) and then bottom edge (3), and then lift the display bezel (4) to remove it.
54 Chapter 5 Removal and replacement procedures for authorized service provider parts
NOTE: The camera and microphone board can be removed after removing the display bezel and before
removing the display panel. See Camera on page 59.
2. If it is necessary to replace the display panel, remove 4 Phillips 2.0x2.5 screws from the display panel
(1), and then lift the display panel (2) to remove it.
Component replacement procedures 55
3. Rotate the display panel (1), disconnect the display cable (2) from the display panel (3), and then lift the
display panel (4) to remove it.
4. If it is necessary to replace the hinge brackets, remove the Phillips 2.5x6.0 screw from the top of each
hinge bracket (1) and the 3 Phillips 2.5x6.0 screws from each hinge (2), remove the hinge brackets from
the back cover (3), and then lift the hinge brackets (4) to remove them.
56 Chapter 5 Removal and replacement procedures for authorized service provider parts
5. Remove the Phillips 2.0x2.0 screw from each hinge bracket (1), and then separate the hinge caps (2)
from the hinge brackets.
6. Remove the Phillips 2.0x2.0 screw from each hinge (1), and then lift the hinges (2) to remove them.
Component replacement procedures 57
7. If it is necessary to replace the WLAN antennas, remove the WLAN antennas (1) from the back cover ,
release the WLAN cable from the routing channels (2), and then lift the antennas and cable to remove
them (3).
Reverse this procedure to install the display assembly and components.
58 Chapter 5 Removal and replacement procedures for authorized service provider parts
Camera
Description Spare part number
Camera
Intel RealSense 3D camera 1p NM U3 1080p 781624-005
HP Wide Vision HD camera 1p DM U2 Mjpeg 720p VDH SF 846006-003
3D camera cable 859445-001
Microphone board (no support for products with AMD hybrid graphics) 857471-001
IMPORTANT: Make special note of each screw and screw lock size and location during removal
and replacement.
Before removing the camera, follow these steps:
1. Shut down the computer.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by rst unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4. Remove the base enclosure (see Base enclosure on page 27).
5. Disconnect the battery (see Battery on page 29), and then remove the following components:
a. Display assembly (see Display assembly on page 32).
b. Display bezel (see Display panel on page 54).
Remove the camera:
1. If it is necessary to replace to remove the camera board, lift the camera board (1), and then disconnect
the camera cable (2) from the camera board.
Component replacement procedures 59
2. If it is necessary to replace the microphone board (select products only), disconnect the cable (1), and
then lift the microphone board (2) to remove it.
Reverse this procedure to install the camera.
60 Chapter 5 Removal and replacement procedures for authorized service provider parts
6 Using Setup Utility (BIOS)
Setup Utility, or Basic Input/Output System (BIOS), controls communication between all the input and output
devices on the system (such as disk drives, display, keyboard, mouse, and printer). Setup Utility (BIOS)
includes settings for the types of devices installed, the startup sequence of the computer, and the amount of
system and extended memory.
NOTE: To start Setup Utility on convertible computers, your computer must be in notebook mode and you
must use the keyboard attached to your notebook.
Starting Setup Utility (BIOS)
CAUTION: Use extreme care when making changes in Setup Utility (BIOS). Errors can prevent the computer
from operating properly.
▲Turn on or restart the computer, quickly press esc, and then press f10.
Updating Setup Utility (BIOS)
Updated versions of Setup Utility (BIOS) may be available on the HP website.
Most BIOS updates on the HP website are packaged in compressed les called SoftPaqs.
Some download packages contain a le named Readme.txt, which contains information regarding installing
and troubleshooting the le.
Determining the BIOS version
To decide whether you need to update Setup Utility (BIOS), rst determine the BIOS version on your computer.
To reveal the BIOS version information (also known as ROM date and System BIOS), use one of these options.
●HP Support Assistant
1. Type support in the taskbar search box, and then select the HP Support Assistant app.
– or –
Click the question mark icon in the taskbar.
2. Select My PC, and then select Specications.
●Setup Utility (BIOS)
1. Start Setup Utility (BIOS) (see Starting Setup Utility (BIOS) on page 61).
2. Select Main, select System Information, and then make note of the BIOS version.
3. Select Exit, select No, and then follow the on-screen instructions.
To check for later BIOS versions, see Downloading a BIOS update on page 62.
Starting Setup Utility (BIOS) 61
Downloading a BIOS update
CAUTION: To reduce the risk of damage to the computer or an unsuccessful installation, download and
install a BIOS update only when the computer is connected to reliable external power using the AC adapter. Do
not download or install a BIOS update while the computer is running on battery power, docked in an optional
docking device, or connected to an optional power source. During the download and installation, follow these
instructions:
●Do not disconnect power from the computer by unplugging the power cord from the AC outlet.
●Do not shut down the computer or initiate Sleep.
●Do not insert, remove, connect, or disconnect any device, cable, or cord.
NOTE: If your computer is connected to a network, consult the network administrator before installing any
software updates, especially system BIOS updates.
1. Type support in the taskbar search box, and then select the HP Support Assistant app.
– or –
Click the question mark icon in the taskbar.
2. Click Updates, and then click Check for updates and messages.
3. Follow the on-screen instructions.
4. At the download area, follow these steps:
a. Identify the most recent BIOS update and compare it to the BIOS version currently installed on your
computer. If the update is more recent than your BIOS version, make a note of the date, name, or
other identier. You may need this information to locate the update later, after it has been
downloaded to your hard drive.
b. Follow the on-screen instructions to download your selection to the hard drive.
Make a note of the path to the location on your hard drive where the BIOS update is downloaded.
You will need to access this path when you are ready to install the update.
BIOS installation procedures vary. Follow any instructions that appear on the screen after the download is
complete. If no instructions appear, follow these steps:
1. Type file in the taskbar search box, and then select File Explorer.
2. Click your hard drive designation. The hard drive designation is typically Local Disk (C:).
3. Using the hard drive path you recorded earlier, open the folder that contains the update.
4. Double-click the le that has an .exe extension (for example, lename.exe).
The BIOS installation begins.
5. Complete the installation by following the on-screen instructions.
NOTE: After a message on the screen reports a successful installation, you can delete the downloaded le
from your hard drive.
62 Chapter 6 Using Setup Utility (BIOS)
7 Using HP PC Hardware Diagnostics (UEFI)
HP PC Hardware Diagnostics is a Unied Extensible Firmware Interface (UEFI) that allows you to run diagnostic
tests to determine whether the computer hardware is functioning properly. The tool runs outside the
operating system so that it can isolate hardware failures from issues that are caused by the operating system
or other software components.
When HP PC Hardware Diagnostics (UEFI) detects a failure that requires hardware replacement, a 24-digit
Failure ID code is generated. This ID code can then be provided to support to help determine how to correct
the problem.
NOTE: To start diagnostics on a convertible computer, your computer must be in notebook mode and you
must use the keyboard attached.
To start HP PC Hardware Diagnostics (UEFI), follow these steps:
1. Turn on or restart the computer, and quickly press esc.
2. Press f2.
The BIOS searches three places for the diagnostic tools, in the following order:
a. Connected USB drive
NOTE: To download the HP PC Hardware Diagnostics (UEFI) tool to a USB drive, see Downloading
HP PC Hardware Diagnostics (UEFI) to a USB device on page 63.
b. Hard drive
c. BIOS
3. When the diagnostic tool opens, select the type of diagnostic test you want to run, and then follow the
on-screen instructions.
NOTE: If you need to stop a diagnostic test, press esc.
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device
NOTE: The HP PC Hardware Diagnostics (UEFI) download instructions are provided in English only, and you
must use a Windows computer to download and create the HP UEFI support environment because only .exe
les are oered.
There are two options to download HP PC Hardware Diagnostics to a USB device.
Download the latest UEFI version
1. Go to http://www.hp.com/go/techcenter/pcdiags. The HP PC Diagnostics home page is displayed.
2. In the HP PC Hardware Diagnostics section, select the Download link, and then select Run.
Download any version of UEFI for a specic product
1. Go to http://www.hp.com/support.
2. Select Get software and drivers.
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device 63
3. Enter the product name or number.
– or –
Select Identify now to let HP automatically detect your product.
4. Select your computer, and then select your operating system.
5. In the Diagnostic section, follow the on-screen instructions to select and download the UEFI version
you want.
64 Chapter 7 Using HP PC Hardware Diagnostics (UEFI)
8 Backing up, restoring, and recovering
This chapter provides information about the following processes. The information in the chapter is standard
procedure for most products.
●Creating recovery media and backups
●Restoring and recovering your system
For additional information, refer to the HP support assistant app.
▲Type support in the taskbar search box, and then select the HP Support Assistant app.
‒ or –
Click the question mark icon in the taskbar.
IMPORTANT: If you will be performing recovery procedures on a tablet, the tablet battery must be at least
70% charged before you start the recovery process.
IMPORTANT: For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before
beginning any recovery process.
Creating recovery media and backups
The following methods of creating recovery media and backups are available on select products only. Choose
the available method according to your computer model.
●Use HP Recovery Manager to create HP Recovery media after you successfully set up the computer. This
step creates a backup of the HP Recovery partition on the computer. The backup can be used to reinstall
the original operating system in cases where the hard drive is corrupted or has been replaced. For
information on creating recovery media, see Creating HP Recovery media (select products only)
on page 65. For information on the recovery options that are available using the recovery media, see
Using Windows tools on page 66.
●Use Windows tools to create system restore points and create backups of personal information.
For more information, see Recovering using HP Recovery Manager on page 67.
NOTE: If storage is 32 GB or less, Microsoft System Restore is disabled by default.
Creating HP Recovery media (select products only)
If possible, check for the presence of the Recovery partition and the Windows partition. From the Start menu,
select File Explorer, and then select This PC.
●If your computer does not list the Windows partition and the Recovery partition, you can obtain recovery
media for your system from support. See the Worldwide Telephone Numbers booklet included with the
computer. You can also nd contact information on the HP website. Go to http://www.hp.com/support,
select your country or region, and follow the on-screen instructions.
Creating recovery media and backups 65
You can use Windows tools to create system restore points and create backups of personal information,
see Using Windows tools on page 66.
●If your computer does list the Recovery partition and the Windows partition, you can use HP Recovery
Manager to create recovery media after you successfully set up the computer. HP Recovery media can be
used to perform system recovery if the hard drive becomes corrupted. System recovery reinstalls the
original operating system and software programs that were installed at the factory and then congures
the settings for the programs. HP Recovery media can also be used to customize the system or restore
the factory image if you replace the hard drive.
—Only one set of recovery media can be created. Handle these recovery tools carefully, and keep
them in a safe place.
—HP Recovery Manager examines the computer and determines the required storage capacity for
the media that will be required.
—To create recovery discs, your computer must have an optical drive with DVD writer capability, and
you must use only high-quality blank DVD-R, DVD+R, DVD-R DL, or DVD+R DL discs. Do not use
rewritable discs such as CD±RW, DVD±RW, double-layer DVD±RW, or BD-RE (rewritable Blu-ray)
discs; they are not compatible with HP Recovery Manager software. Or, instead, you can use a high-
quality blank USB ash drive.
—If your computer does not include an integrated optical drive with DVD writer capability, but you
would like to create DVD recovery media, you can use an external optical drive (purchased
separately) to create recovery discs. If you use an external optical drive, it must be connected
directly to a USB port on the computer; the drive cannot be connected to a USB port on an external
device, such as a USB hub. If you cannot create DVD media yourself, you can obtain recovery discs
for your computer from HP. See the Worldwide Telephone Numbers booklet included with the
computer. You can also nd contact information on the HP website. Go to http://www.hp.com/
support, select your country or region, and follow the on-screen instructions.
—Be sure that the computer is connected to AC power before you begin creating the recovery media.
—The creation process can take an hour or more. Do not interrupt the creation process.
—If necessary, you can exit the program before you have nished creating all of the recovery DVDs.
HP Recovery Manager will nish burning the current DVD. The next time you start HP Recovery
Manager, you will be prompted to continue.
To create HP Recovery media:
IMPORTANT: For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before
beginning these steps.
1. Type recovery in the taskbar search box, and then select HP Recovery Manager.
2. Select Create recovery media, and then follow the on-screen instructions.
If you ever need to recover the system, see Recovering using HP Recovery Manager on page 67.
Using Windows tools
You can create recovery media, system restore points, and backups of personal information using Windows
tools.
NOTE: If storage is 32 GB or less, Microsoft System Restore is disabled by default.
For more information and steps, see the Get started app.
▲Select the Start button, and then select the Get started app.
66 Chapter 8 Backing up, restoring, and recovering
Restore and recovery
There are several options for recovering your system. Choose the method that best matches your situation
and level of expertise:
IMPORTANT: Not all methods are available on all products.
●Windows oers several options for restoring from backup, refreshing the computer, and resetting the
computer to its original state. For more information see the Get started app.
▲Select the Start button, and then select the Get started app.
●If you need to correct a problem with a preinstalled application or driver, use the Reinstall drivers and/or
applications option (select products only) of HP Recovery Manager to reinstall the individual application
or driver.
▲Type recovery in the taskbar search box, select HP Recovery Manager, select Reinstall drivers
and/or applications, and then follow the on-screen instructions.
●If you want to recover the Windows partition to original factory content, you can choose the System
Recovery option from the HP Recovery partition (select products only) or use the HP Recovery media.
For more information, see Recovering using HP Recovery Manager on page 67. If you have not already
created recovery media, see Creating HP Recovery media (select products only) on page 65.
●On select products, if you want to recover the computer's original factory partition and content, or if you
have replaced the hard drive, you can use the Factory Reset option of HP Recovery media. For more
information, see Recovering using HP Recovery Manager on page 67.
●On select products, if you want to remove the recovery partition to reclaim hard drive space, HP
Recovery Manager oers the Remove Recovery Partition option.
For more information, see Removing the HP Recovery partition (select products only) on page 70.
Recovering using HP Recovery Manager
HP Recovery Manager software allows you to recover the computer to its original factory state by using the
HP Recovery media that you either created or that you obtained from HP, or by using the HP Recovery
partition (select products only). If you have not already created recovery media, see Creating HP Recovery
media (select products only) on page 65.
What you need to know before you get started
●HP Recovery Manager recovers only software that was installed at the factory. For software not provided
with this computer, you must either download the software from the manufacturer's website or reinstall
the software from the media provided by the manufacturer.
IMPORTANT: Recovery through HP Recovery Manager should be used as a nal attempt to correct
computer issues.
●HP Recovery media must be used if the computer hard drive fails. If you have not already created
recovery media, see Creating HP Recovery media (select products only) on page 65.
●To use the Factory Reset option (select products only), you must use HP Recovery media. If you have not
already created recovery media, see Creating HP Recovery media (select products only) on page 65.
●If your computer does not allow the creation of HP Recovery media or if the HP Recovery media does not
work, you can obtain recovery media for your system from support. See the Worldwide Telephone
Numbers booklet included with the computer. You can also nd contact information from the HP
Restore and recovery 67
website. Go to http://www.hp.com/support, select your country or region, and follow the on-screen
instructions.
IMPORTANT: HP Recovery Manager does not automatically provide backups of your personal data. Before
beginning recovery, back up any personal data you want to retain.
Using HP Recovery media, you can choose from one of the following recovery options:
NOTE: Only the options available for your computer display when you start the recovery process.
●System Recovery—Reinstalls the original operating system, and then congures the settings for the
programs that were installed at the factory.
●Factory Reset—Restores the computer to its original factory state by deleting all information from the
hard drive and re-creating the partitions. Then it reinstalls the operating system and the software that
was installed at the factory.
The HP Recovery partition (select products only) allows System Recovery only.
Using the HP Recovery partition (select products only)
The HP Recovery partition allows you to perform a system recovery without the need for recovery discs or a
recovery USB ash drive. This type of recovery can be used only if the hard drive is still working.
To start HP Recovery Manager from the HP Recovery partition:
IMPORTANT: For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before
beginning these steps (select products only).
1. Type recovery in the taskbar search box, select Recovery Manager, and then select HP Recovery
Environment.
- or-
For computers or tablets with keyboards attached, press f11 while the computer boots, or press and
hold f11 as you press the power button.
For tablets without keyboards:
Turn on or restart the tablet, and then quickly hold down the volume down button; then select f11.
- or -
Turn on or restart the tablet, and then quickly hold down the Windows button; then select f11.
2. Select Troubleshoot from the boot options menu.
3. Select Recovery Manager, and then follow the on-screen instructions.
Using HP Recovery media to recover
You can use HP Recovery media to recover the original system. This method can be used if your system does
not have an HP Recovery partition or if the hard drive is not working properly.
1. If possible, back up all personal les.
2. Insert the HP Recovery media, and then restart the computer.
NOTE: If the computer does not automatically restart in HP Recovery Manager, change the computer
boot order. See Changing the computer boot order on page 69.
3. Follow the on-screen instructions.
68 Chapter 8 Backing up, restoring, and recovering
Changing the computer boot order
If your computer does not restart in HP Recovery Manager, you can change the computer boot order, which is
the order of devices listed in BIOS where the computer looks for startup information. You can change the
selection to an optical drive or a USB ash drive.
To change the boot order:
IMPORTANT: For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before
beginning these steps.
1. Insert the HP Recovery media.
2. Access BIOS:
For computers or tablets with keyboards attached:
▲Turn on or restart the computer or tablet, quickly press esc, and then press f9 for boot options.
For tablets without keyboards:
▲Turn on or restart the tablet, and then quickly hold down the volume down button; then select f9.
- or -
Turn on or restart the tablet, and then quickly hold down the Windows button; then select f9.
3. Select the optical drive or USB ash drive from which you want to boot.
4. Follow the on-screen instructions.
Restore and recovery 69
Removing the HP Recovery partition (select products only)
HP Recovery Manager software allows you to remove the HP Recovery partition to free up hard drive space.
IMPORTANT: After you remove the HP Recovery partition, you will not be able to perform System Recovery
or create HP recovery media from the HP Recovery partition. So before you remove the Recovery partition,
create HP Recovery media; see Creating HP Recovery media (select products only) on page 65.
NOTE: The Remove Recovery Partition option is only available on products that support this function.
Follow these steps to remove the HP Recovery partition:
1. Type recovery in the taskbar search box, and then select HP Recovery Manager.
2. Select Remove Recovery Partition, and then follow the on-screen instructions.
70 Chapter 8 Backing up, restoring, and recovering
9Specications
Computer specications
Metric U.S.
Dimensions
Width 382.4 mm 15.06 in
Depth 252.5 mm 9.94 in
Height (front to back) 24.5 mm .96 in
Weight
Products with hard drive 2200.5 g 4.85 lb
Products with SSD 2095.4 g 4.62 lb
Input power
Operating voltage and current 19.5 V dc @ 6.15 A – 120 W
19.5 V dc @ 7.70 A – 150 W
Temperature
Operating 5°C to 35°C 41°F to 95°F
Nonoperating ‑20°C to 60°C ‑4°F to 140°F
Relative humidity (noncondensing)
Operating 10% to 90%
Nonoperating 5% to 95%
Maximum altitude (unpressurized)
Operating ‑15 m to 3,048 m ‑50 ft to 10,000 ft
Nonoperating ‑15 m to 12,192 m ‑50 ft to 40,000 ft
NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The device operates well within this range of
temperatures.
Computer specications 71
39.62 cm (15.6 in) display specications
Metric U.S.
Dimensions
Height 20.77 cm 8.175 in
Width 37.78 cm 14.875 in
Diagonal 39.62 cm 15.6 in
Number of colors Up to 16.8 million
Contrast ratio 500:1 (typical)
Brightness 220, 250, or 300 nits
Pixel resolution
Pitch 0.252mm x 0.252mm
Format 1920x1080 or 3840x2160
Conguration RGB vertical stripe
Backlight LED
Character display 80 × 25
Total power consumption 2.0 W
Viewing angle ±65° horizontal, ±50° vertical (typical)
Hard drive specications
1 TB* 2TB*
Dimensions
Height 9.5 mm 9.5 mm
Width 69.85 mm 69.85 mm
Weight 102 g max 130 g max
Interface type SATA 3.0 SATA 3.0
Transfer rate 600 MB/sec 600 MB/sec
Security ATA-8 security ATA-8 security
Seek times (typical read, including setting)
Single track 2 ms 2 ms
Average 13.0 ms 12.0 ms
Maximum 15.0 ms 22.0 ms
Logical blocks 1,953,525,168 3,907,029,168
Disk rotational speed 5400 rpm 5400 rpm
Operating temperature 0°C to 60°C (0°F to 140°F) 0°C to 60°C (0°F to 140°F)
72 Chapter 9 Specications
1 TB* 2TB*
*Size refers to hard drive storage capacity. Actual accessible capacity is less. Actual drive specications may dier slightly.
NOTE: Certain restrictions and exclusions apply. Contact support for details.
Hard drive specications 73
10 Power cord set requirements
The wide-range input feature of the computer permits it to operate from any line voltage from 100 to 120 V
ac, or from 220 to 240 V ac.
The 3-conductor power cord set included with the computer meets the requirements for use in the country or
region where the equipment is purchased.
Power cord sets for use in other countries or regions must meet the requirements of the country and region
where the computer is used.
Requirements for all countries
The following requirements are applicable to all countries and regions:
●The length of the power cord set must be at least 1.0 m (3.3 ft) and no more than 2.0 m (6.5 ft).
●All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in
the country or region where the power cord set will be used.
●The power cord sets must have a minimum current capacity of 10 A and a nominal voltage rating of 125
or 250 V ac, as required by the power system of each country or region.
●The appliance coupler must meet the mechanical conguration of an EN 60 320/IEC 320 Standard Sheet
C13 connector for mating with the appliance inlet on the back of the computer.
74 Chapter 10 Power cord set requirements
Requirements for specic countries and regions
Country/region Accredited agency Applicable note number
Argentina IRAM 1
Australia SAA 1
Austria OVE 1
Belgium CEBEC 1
Brazil ABNT 1
Canada CSA 2
Chile IMQ 1
Denmark DEMKO 1
Finland FIMKO 1
France UTE 1
Germany VDE 1
India ISI 1
Israel SII 1
Italy IMQ 1
Japan JIS 3
The Netherlands KEMA 1
New Zealand SANZ 1
Norway NEMKO 1
The People's Republic of China CCC 4
Saudi Arabia SASO 7
Singapore PSB 1
South Africa SABS 1
South Korea KTL 5
Sweden SEMKO 1
Switzerland SEV 1
Taiwan BSMI 6
Thailand TISI 1
The United Kingdom ASTA 1
The United States UL 2
1. The exible cord must be Type HO5VV-F, 3-conductor, 0.75 mm² conductor size. Power cord set ttings (appliance coupler and
wall plug) must bear the certication mark of the agency responsible for evaluation in the country or region where it will be used.
2. The exible cord must be Type SVT/SJT or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding type
with a NEMA 5-15P (15 A, 125 V ac) or NEMA 6-15P (15 A, 250 V ac) conguration. CSA or C-UL mark. UL le number must be on
each element.
Requirements for specic countries and regions 75
Country/region Accredited agency Applicable note number
3. The appliance coupler, exible cord, and wall plug must bear a “T” mark and registration number in accordance with the Japanese
Dentori Law. The exible cord must be Type VCTF, 3-conductor, 0.75 mm² or 1.25 mm² conductor size. The wall plug must be a
two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V ac) conguration.
4. The exible cord must be Type RVV, 3-conductor, 0.75 mm² conductor size. Power cord set ttings (appliance coupler and wall
plug) must bear the CCC certication mark.
5. The exible cord must be Type H05VV-F 3-conductor, 0.75 mm² conductor size. KTL logo and individual approval number must
be on each element. Corset approval number and logo must be printed on a ag label.
6. The exible cord must be Type HVCTF 3-conductor, 1.25 mm² conductor size. Power cord set ttings (appliance coupler, cable,
and wall plug) must bear the BSMI certication mark.
7. For 127 V ac, the exible cord must be Type SVT or SJT 3-conductor, 18 AWG, with plug NEMA 5-15P (15 A, 125 V ac), with UL and
CSA or C-UL marks. For 240 V ac, the exible cord must be Type H05VV-F 3-conductor, 0.75 mm² or 1.00 mm2 conductor size,
with plug BS 1363/A with BSI or ASTA marks.
76 Chapter 10 Power cord set requirements
11 Recycling
When a non-rechargeable or rechargeable battery has reached the end of its useful life, do not dispose of the
battery in general household waste. Follow the local laws and regulations in your area for battery disposal.
HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable
batteries. For more information about recycling programs, see the HP Web site at http://www.hp.com/recycle.
77
Index
A
AC adapter and battery 5
AC adapter, spare part numbers 20
action keys 11
airplane mode key 12
audio, product description 3
audio-out (headphone)/audio-in
(microphone) jack, identifying 6
B
back cover
spare part number 20, 54
backups 65
base enclosure
removal 27
spare part number 18
base enclosure, spare part number
27
battery
removal 29
spare part number 18, 29
battery cable
spare part number 18
bezel
spare part number 19, 54
BIOS
determining version 61
downloading an update 62
starting the Setup Utility 61
updating 61
Bluetooth label 15
boot order
changing 69
bottom 15
buttons
left TouchPad 8
power 10
right TouchPad 8
C
camera
identifying 7
removal 59
spare part number 19, 59
spare part numbers 59
camera cable
spare part number 19, 59
camera light, identifying 7
caps lock light, identifying 9
chipset, product description 1
color
product description 1
components
bottom 13
display 7
left side 6
rear 14
right side 5
top 8
computer major components 16
computer specications 71
connector, power 5
D
display
specications 72
display assembly
removal 32, 54
spare part numbers 32, 54
subcomponents 19
display cable
spare part number 20, 54
Display panel
spare part numbers 17
display panel
product description 1
spare part number 54
drive light 5
E
esc key, identifying 11
Ethernet, product description 3
F
fan
spare part number 18
fans
removal 42
spare part numbers 42
fn key, identifying 11
G
graphics, product description 1
H
hard drive
product description 2
removal 34
spare part number 18
spare part numbers 34
specications 72
HDMI port, identifying 5
heat sink
spare part number 18
heat sink for CPU and graphics
removal 44
spare part numbers 44
heat sink for discrete graphics
memory
removal 43
spare part numbers 43
hinge assembly
spare part number 20, 54
hinge cap assembly
spare part number 20, 54
HP PC Hardware Diagnostics (UEFI)
using 63
HP Recovery Manager
correcting boot problems 69
starting 68
HP Recovery media
creating 65
recovery 68
HP Recovery partition
recovery 68
removing 70
I
integrated numeric keypad,
identifying 11
internal microphones, identifying 7
J
jacks
audio-out (headphone)/audio-in
(microphone) 6
78 Index
network 5
RJ-45 (network) 5
K
Keyboard
spare part numbers 17
keyboard
product description 3
keys
airplane mode 12
esc 11
fn 11
Windows 11
L
labels
Bluetooth 15
regulatory 15
serial number 14
service 14
wireless certication 15
WLAN 15
lights
AC adapter and battery light 5
caps lock 9
drive 5
mute 9
power 9
RJ-45 (network) status 5
M
mechanical requirements, product
description 4
memory
removal 37
spare part numbers 18, 37
memory card reader, identifying 5
memory card, identifying 5
memory module
product description 2
minimized image recovery 68
minimized image, creating 67
model name 1
mute light, identifying 9
N
network jack, identifying 5
O
operating system, product
description 4
optical drive
product description 2
original system recovery 67
P
pointing device, product
description 3
ports
HDMI 5
product description 3
USB 2.0 6
USB 3.0 6
power button board
removal 41
spare part number 18
spare part numbers 41
power button board cable
spare part number 18
power button, identifying 10
power connector
removal 50
spare part number 18, 50
spare part numbers 50
power connector, identifying 5
power cord
requirements for all countries
74
requirements for specic
countries and regions 75
set requirements 74
spare part numbers 20
power lights, identifying 9
power requirements, product
description 3
processor
product description 1
product description
audio 3
camera 2
chipset 1
color 1
display panel 1
Ethernet 3
external media cards 3
graphics 1
hard drive 2
keyboard 3
mechanical requirements 4
memory module 2
microphone 2
operating system 4
optical drive 2
pointing device 3
ports 3
power requirements 3
processors 1
product name 1
security 4
serviceability 4
wireless 3
product name 1
product name and number,
computer 14
R
raw panel
spare part number 19
recover
options 67
recovery
discs 66, 68
HP Recovery Manager 67
media 68
starting 68
supported discs 66
system 67
USB ash drive 68
using HP Recovery media 66
recovery media
creating 65
creating using HP Recovery
Manager 66
recovery partition
removing 70
regulatory information
regulatory label 15
wireless certication labels 15
removal/replacement
procedures 27
RJ-45 (network) jack, identifying 5
RJ-45 (network) status lights,
identifying 5
RTC battery
removal 49
spare part number 17
spare part numbers 49
S
screw kit 21
security cable slot, identifying 6
Index 79
security, product description 4
serial number 14
serial number, computer 14
service labels, locating 14
serviceability, product description 4
slots
memory card reader 5
security cable 6
solid-state drive
spare part numbers 18
speaker
removal 46
spare part numbers 46
speakers
identifying 10
spare part number 17
specications
computer 71
display 72
hard drive 72
SSD
removal 36
spare part numbers 36
supported discs, recovery 66
system board
removal 47
spare part numbers 18, 47
system recovery 67
system restore point
creating 66
system restore point, creating 65
T
Top cover
spare part numbers 17
TouchPad
buttons 8
removal 52
spare part numbers 17, 52
TouchPad board
spare part numbers 17
TouchPad zone, identifying 8
traveling with the computer 15
U
USB 2.0 port, identifying 6
USB 3.0 port 5
USB 3.0 port, identifying 6
USB board
removal 40
spare part number 18
spare part numbers 40
USB board cable
spare part number 17
USB ports, identifying 5
V
vents, identifying 13, 14
W
Windows
system restore point 65, 66
Windows key, identifying 11
Windows tools
using 66
wireless certication label 15
wireless, product description 3
WLAN antenna, spare part number
20, 54
WLAN antennas, identifying 7
WLAN assembly
spare part number 54
WLAN device 15
WLAN label 15
WLAN module
removal 39
spare part number 18, 39
80 Index