Indesit BI WMIL 71252 EU User Manual
Displayed below is the user manual for BI WMIL 71252 EU by Indesit which is a product in the Washing Machines category. This manual has pages.
Related Manuals
GB
Quick Guide
CONTROL PANEL
1. ON/OFF button
2. START/PAUSE button with indicator light
3. WASH CYCLE PROGRESS indicator lights
4. DOOR LOCKED indicator light
5. FUNCTION buttons with indicator lights
6. CHILDLOCK button with indicator light
7. DELAY TIMER button
8. SPIN button
9. TEMPERATURE button
10. WASH CYCLE knob
11. PUSH & GO button
WASH CYCLE TABLE
For all testing institutes:
2) Long cotton cycle: set cycle 6 at a temperature of 40°C.
3) Long synthetics cycle: set cycle 7 at a temperature of 40°C.
* By selecting the cycle and excluding the spin cycle, the washing machine will drain only.
The cycle duration indicated on the display or instruction manual is an estimate based on
standard conditions. The actual duration may vary in relation to several factors, such as
the temperature and pressure of the incoming water, ambient temperature, amount of
detergent, load quantity and type, load balancing and any additional options selected.
1) Test wash cycle in compliance with regulation 1061/2010:
This cycle is designed for normally soiled cotton loads and is the most ecient in terms of
both electricity and water consumption; it should be used for garments washable at 60°C or
at 40°C. The actual washing temperature may dier from the indicated value.
PRODUCT DESCRIPTION
1. Top
2. Detergent dispenser drawer
3. Control panel
4. Handle
5. Porthole door
6. Drain pump
7. Adjustable feet (4)
THANK YOU FOR BUYING A INDESIT PRODUCT
In order to receive a more complete assistance,
please register your product on
www.indesit.com/register
Before using the appliance carefully read the Safety Instruction.
Before using the machine, it is imperative that the transport bolts are removed.
For more detailed instructions on how to remove them, see the Installation Guide.
Maximum load 7 kg
Power input in o mode 0,5 W / in left-on mode 8 W
Detergents and
Additives
Recommended
detergent
Residual
dampness %
Energy con-
sumption kWh
Total water l
Wash cycle Temperature Maximum
spin
(r.p.m.)
Maximum
load
(kg)
Duration
(minutes)
Wash Fabric
softener Powder Liquid
Default Range 2 3
1 Daily cotton 30°C – 30°C 1200 3,5 100 –– – –
2 Daily synthetics 30°C – 30°C 1000 3,5 90 –– – –
3 Coloureds 30°C – 30°C 1000 3,5 95 –– – –
4 Delicates 30°C – 30°C 0 1,0 80 –– – –
5 Rapid 30min 30°C – 30°C 800 3,5 30 –70 0,16 33
6 Cotton (2) 40°C – 60°C 1200 7,0 220 53 0,97 75
7 Synthetics (3) 40°C – 60°C 1200 3,5 195 33 0,75 72
8 Mixed 40°C – 40°C 1200 7,0 100 –- - -
9 Eco cotton (1) 60°C 60°C 1200 7,0 215 53 1,08 52,5
40°C 1200 7,0 220 53 0,97 75
10 White cotton 60°C – 90°C 1200 7,0 130 – – –
11 Sport 40°C – 40°C 600 3,5 90 –– – –
12 Duvet 30°C – 30°C 1000 2,0 110 –– – –
13 Wool 40°C – 40°C 800 1,5 70 –– – –
14 Anti odour 40°C – 40°C 1000 3,0 100 –– – –
Rinse + Spin – – 1200 7,0 50 – – – – – –
Spin + Drain * – – 1200 7,0 10 – – – – – – –
Required dosage Optional dosage
DETERGENT DISPENSER DRAWER
Compartment 1:
Do not insert detergent in this compartment.
Compartment 2: Washing detergent (powder
or liquid)
Compartment 3: Additives (fabric softener, etc.)
The fabric softener must never exceed the
“max” level indicated on the central pin.
! Use powder detergent for white cotton
garments, for pre-washing, and for washing at
temperatures over 60°C.
! Follow the instructions given on the detergent
packaging.
1
2
3
1.
3.
2.
5.
4.
6.
7.
1
10
23
6
9
11
4
87
5
WASH CYCLES
Follow the instructions on the symbols of the garment’s wash
care label. The value indicated in the symbol is the maximum
recommended temperature for washing the garment.
Daily cotton
A 30°C cycle for cotton garments. It allows for reducing electricity
consumption for heating the water while guaranteeing good washing
performance. Suitable for lightly soiled garments.
Daily synthetics
A 30°C cycle for synthetic garments. It allows for reducing electricity
consumption for heating the water while guaranteeing good washing
results. Suitable for lightly soiled garments.
Coloureds
A 30°C cycle that helps to preserve colours, suitable for cotton or
synthetic coloured garments. It allows for reducing electricity
consumption for heating the water while guaranteeing good washing
results. Suitable for lightly soiled garments.
Delicates
Suitable for washing very delicate garments. It is advisable to turn the
garments inside out before washing them. For best results, use liquid
detergent on delicate garments. For washing silk items and curtains,
select cycle 4 and activate the option; the machine will end the
cycle with the laundry soaked and the indicator light will ash. To drain
the water so that the laundry can be removed, press the START/PAUSE
button or the button.
Rapid 30min
For washing lightly soiled garments in a short time. Not suitable for wool,
silk and garments to be washed by hand.
Cotton
Suitable for washing towels, underwear, table cloths, etc. made of
resistant linen and cotton that are moderately to heavily soiled.
Synthetics
Suitable for washing moderately soiled garments made of synthetic bres
(e.g. polyester, polyacrylic, viscose, etc.) or mixed synthetic-cotton bres.
Mixed
A 40°C cycle for washing cotton and synthetic garments together.
Suitable for lightly soiled underwear.
Eco cotton
Suitable for washing moderately soiled cotton garments. At 40°C and
60°C it is the standard cycle for washing cotton garments, and is the most
ecient in terms of combined water and electricity consumption.
White cotton
For heavily soiled whites and resistant colours.
Sport
A cycle designed for washing lightly soiled sports clothing (tracksuits,
shorts, etc.); for best results, we recommend not exceeding the maximum
load indicated in the “Wash Cycle Table”. We recommend using liquid
detergent and adding the amount suitable for a half-load.
Duvet
For washing clothing padded with goose down, such as double or single
duvets (weighing under 2 kg), cushions or down jackets. Duvets should
be loaded into the drum with their edges folded inwards and no more
than ¾ of the total drum volume should be used up. For best results, it is
advisable to use liquid detergent to be poured into the detergent drawer.
Wool - Woolmark Apparel Care - Blue:
The “Wool” wash cycle is approved by the Woolmark
Company for washing wool garments classied as
“hand-washable”, provided that the wash complies with
the instructions appearing on the garment’s label and
with those provided by the manufacturer of this washing
machine (M1126).
Anti odour
Use this cycle (for synthetic fabrics) to wash garments with bad odours
(e.g. smoke, sweat, fried food). The cycle is designed to remove bad
odours while preserving the fabric bres.
Rinse + Spin
Designed for rinsing and spinning.
Spin + Drain
Designed to spin and drain the water.
WASH CYCLE PHASE INDICATOR LIGHTS
Once the desired wash cycle has been selected and has begun, the
indicator lights switch on one-by-one to indicate which phase of the cycle
is currently in progress.
Wash
Rinse
Spin
Drain
End of Wash Cycle
DOOR LOCKED INDICATOR
When lit, the symbol indicates that the door is locked. To prevent any
damage, wait until the symbol turns o before opening the door.
To open the door while a cycle is in progress, press the START/PAUSE
button; if the indicator light is o, the door can be opened.
FIRSTTIME USE
Once the appliance has been installed, and before it is used for the rst
time, run a wash cycle with detergent and no laundry, by setting the
“Auto-Clean” cycle.
DAILY USE
Prepare the laundry by following the suggestions appearing under the
“TIPS AND SUGGESTIONS” section.
Rapid programming
- Open the door. Load the laundry while making sure not to exceed the
maximum load quantity indicated in the cycle table.
- Pull out the detergent dispenser drawer and pour the detergent into the
relevant compartments as described in “DETERGENT DISPENSER DRAWER
section”.
- Close the door.
- Press the PUSH & GO button to start the wash cycle.
Traditional programming
- Turn the washing machine on by pressing the ON/OFF button. All the
indicator lights will light up for a few seconds, then only the lights
corresponding to the settings for the selected wash cycle will remain lit;
the START/PAUSE indicator light will also ash.
- Open the door. Load the laundry while making sure not to exceed the
maximum load quantity indicated in the Wash Cycle Table.
- Pull out the detergent dispenser drawer and pour the detergent into the
relevant compartments as described in “DETERGENT DISPENSER
DRAWER” section.
- Close the door.
- Set the WASH CYCLE knob to the desired cycle.
- Modify the temperature and/or spin: pressing the
40°
60°
button allows
for gradually reducing the temperature down to the cold wash level
(20°C). The spin speed may be progressively reduced by pressing the
button, until it is completely excluded (the “ ” setting. If these buttons
are pressed again, the maximum values are restored.
- Select the desired wash cycle.
- Select the desired options.
- Press the START/PAUSE button to start the wash cycle; the relative
indicator light will light up steady green and the door will lock ( indicator
light on).
PAUSING A CYCLE
To pause the wash cycle, press the START/PAUSE button again; the
indicator light will ash . If the indicator light is not lit, the door may be
opened. To start the wash cycle from the point at which it was
interrupted, press the START/PAUSE button again.
OPENING THE DOOR, IF NECESSARY
Once a cycle starts, the indicator light turns on to signal that the door
cannot be opened. While a wash cycle is running, the door remains
locked. To open the door while a cycle is under way, for example, to add
or remove garments, press the START/PAUSE button to pause the
cycle; the indicator light will ash . If the indicator light is not lit, the
door may be opened. Press the START/PAUSE button again to
continue the cycle.
CHANGING A RUNNING WASH CYCLE
To change a wash cycle while it is in progress, pause the washing machine
using the START/PAUSE button (the relative indicator light will ash ),
then select the desired cycle and press the START/PAUSE button
again.
! To cancel a cycle that has already begun, press and hold the ON/OFF
button.
The cycle will be stopped and the machine will switch o.
END OF THE CYCLE
Once the cycle terminates the indicator light will light up; when the
indicator light switches o, the door may be opened. Open the door,
unload the laundry and switch o the machine. If you do not press “ON/
OFF” button, the washing machine will switch o automatically after
about a half of an hour. Close the water tap, open the door and unload
the washing machine. Leave the door ajar to allow the drum to dry.
FUNCTIONS
- If the selected option is not compatible with the set wash cycle, the
indicator light will ash and the option will not be activated.
- If the selected option is not compatible with another previously
selected option, the indicator light will ash accompanied by a buzzer,
and only the latter option will be activated; the indicator light
corresponding to the activated option will turn on.
Stain removal
This option allows for selecting the type of dirt so as to optimally adjust the
cycle for removing the stains. The following types of dirt can be selected:
- Food: for stains caused by foodstus and beverages, for example.
- Work: for grease and ink stains, for example.
- Outdoor: for mud and grass stains, for example.
! The wash cycle duration varies according to the type of selected dirt.
Extra rinse
By selecting this option, the eciency of the rinse is increased and
optimal detergent removal is guaranteed. It is particularly useful for
sensitive skin.
Easy iron
By selecting this function, the wash and spin cycles will be modied in
order to limit the formation of creases. At the end of the cycle the
washing machine’s drum will rotate slowly; the EASY IRON and START/
PAUSE indicator lights will ash and the phase will remain lit
steady. To end the cycle, press the START/PAUSE button or the EASY
IRON button.
Delay start
To set a delayed start for the selected cycle, press the corresponding
button repeatedly until the desired delay period has been reached
(3h-6h-9h). When the button is pressed for the fourth time, the option will
deactivate.
Once the START/PAUSE button has been pressed, the delay time can
only be modied by decreasing it until the set cycle is launched.
Temperature
40°
60°
Each wash cycle has a pre-dened temperature. To modify the
temperature, press the
40°
60°
button.
Spin
Each wash cycle has a pre-dened spin speed. To modify the spin speed,
press the button.
Push & Go
This function allows for starting a wash cycle even when the machine is
switched o without having to press the ON/OFF button in advance
or, after switching the machine on, without having activated any other
button and/or selector knob (otherwise the Push & Go cycle will be
deactivated). To start the Push & Go cycle press and hold the relative
button for 2 seconds. The lit indicator light indicates that the cycle has
started. This wash cycle is ideal for cotton or synthetic fabrics, as it washes
at a temperature of 30°C and a maximum spin speed of 1.000 rpm. Max
load 3,5 kg (cycle duration 45’).
How does it work?
1. Load the laundry (cotton and/or synthetic garments) and close the
door.
2. Pour the detergent and additives.
3. Start the cycle by pressing and holding the Push & Go button for 2
seconds. The relevant indicator light will turn green and the door will lock
(the symbol lights up).
N.B.: starting the wash cycle through the Push & Go button activates
an automatic non-customisable cycle recommended for cotton and
synthetic fabrics. This cycle does not allow for setting any additional
options.
To open the door while an automatic cycle is under way, press the START/
PAUSE button; if the locked door symbol is o, the door may be
opened. Press the START/PAUSE button again to restart the cycle from
the point at which it was interrupted.
4. Once the programme is nished, the indicator light turns on.
CHILD LOCK
to activate the control panel lock, press and hold the button for
approximately 2 seconds. The lit symbol signals that the control
panel is locked. This prevents wash cycles from being modied
accidentally (except for the ON/OFF button), especially if there are
children in the home. To deactivate the control panel lock, press and hold
the button for approximately 2 seconds.
TIPS AND SUGGESTIONS
Divide the laundry according to:
Type of fabric (cotton, mixed bres, synthetics, wool, garments to be
hand-washed). Colour (separate coloured garments from whites, wash
new coloured garments separately). Delicates (small garments – such as
nylon stockings – and items with hooks – such as bras: insert them in a
fabric bag).
Empty the pockets:
Objects such as coins or lighters can damage the washing machine and
the drum. Check all buttons.
CARE AND MAINTENANCE
Before performing cleaning and maintenance, switch the washing machine
o and disconnect it from the mains power. Do not use ammable liquids to
clean the washing machine.
Disconnect the water and power supplies
Close the water tap after every wash. This will limit wear on the hydraulic
system inside the washing machine and help to prevent leaks.
Unplug the washing machine when cleaning it and during all
maintenance work.
Clean the washing machine
The outer parts and rubber components of the appliance can be cleaned
using a soft cloth soaked in lukewarm soapy water. Do not use solvents or
abrasives.
The washing machine has a “Auto-clean” cycle for its internal parts; it must
be run without any load in the drum.
To optimise this cycle, it is possible to use either detergent (10% of the
quantity specied for lightly soiled garments) or special additives to clean
the washing machine. We recommend running a cleaning cycle every 40
wash cycles.
To start the cycle press buttons and simultaneously for 5 seconds.
The cycle will start automatically and will run for about 70 minutes. To
stop the cycle, press the START/PAUSE button.
Clean the detergent dispenser drawer
Wash it under running water; this operation should be repeated frequently.
Care for the door and drum
Always leave the porthole door ajar in order to prevent unpleasant odours
from forming.
Clean the pump
The washing machine is tted with a auto-cleaning pump that does not
require any maintenance. Small items (such as coins or buttons) may
sometimes fall into the protective pre-chamber situated at the base of the
pump.
! Make sure the wash cycle has ended and unplug the appliance.
To access the pre-chamber:
1. loosen the drainage pump cover by turning it anti-clockwise: it is
normal for some water to leak out;
2. clean the inside thoroughly;
3. screw the cover back on;
Check the water inlet hose
Check the water inlet hose at least once a year. If it is cracked or broken, it
must be replaced: during wash cycles, the high pressure of the water
could suddenly split the hose open.
! Never use hoses that have already been used.
LOAD BALANCING SYSTEM
Before every spin cycle, to avoid excessive vibrations before every
spin and to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the washing
rotation speed. If, after several attempts, the load is not balanced
correctly, the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washing machine performs the distribution
process instead of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are mixed in the load.
TRANSPORT AND HANDLING
Do not lift the washing machine by gripping it from the upper section.
Unplug the appliance and close the water tap. Check that the door and
detergent dispenser drawer are tightly closed. Detach the lling hose
from the water tap then detach the drain hose. Empty all the water
remaining in the hoses and secure the latter so that they do not get
damaged during transport. Apply the transport bolts back on. Repeat, in
reverse order, the transport bolt removal procedure described in the
“Health & Safety and Installation Guides”.
TROUBLESHOOTING
The washing machine may occasionally fail to work. Before contacting the Technical Assistance Service, make sure that the problem cannot be easily
solved using the following list.
Anomalies Possible causes / Solution
The washing machine does
not start.
The appliance is not plugged into the socket, or not suciently to make contact.
There is no power in the house.
The wash cycle does not start.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delay has been set for the start time.
The machine does not ll with
water or the indicator light
for the rst wash cycle stage
ashes rapidly.
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The washing machine
continuously loads and
unloads water.
The drain hose is not tted between 65 and 100 cm from the oor.
The free end of the hose is immersed in water.
The wall drainage system does not have a breather pipe.
If the problem persists even after these checks, turn o the water tap, switch the appliance o and contact the
Technical Assistance Service. If the home is on one of the upper oors of a building, there may be problems relating
to back-siphonage, causing the washing machine to ll with water and drain continuously. Special anti-siphon
valves are available in shops and help to prevent this inconvenience.
The washing machine does
not drain or spin.
The cycle does not include drainage: with certain cycles it must be started manually.
The drain hose is bent.
The option is enabled: to complete the wash cycle, press the START/PAUSE button.
The drainage duct is clogged.
The washing machine
vibrates a lot during the spin
cycle.
The drum was not unlocked correctly during installation.
The washing machine is not level.
The washing machine is tucked between furniture cabinets and the wall.
The washing machine leaks.
The water inlet hose is not screwed on properly.
The detergent dispenser drawer is obstructed.
The drain hose is not properly attached.
The “Options” lights and the
START/PAUSE indicator light
ash while one of the wash
cycle progress and DOOR
LOCKED lights are lit in a xed
manner.
Switch o the machine and unplug it, wait for approximately 1 minute and then switch it back on again.
If the problem persists, contact the Technical Assistance Service .
There is too much foam.
The detergent is not suitable for machine washing (it should be marked with “for washing machine use” or “hand
wash and machine wash” or similar).
Too much detergent was used.
The Push & Go function does
not activate.
After switching on the machine, a control other than Push & Go was activated. Switch the machine o and press the
Push & Go button.
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
• Visiting our website - http://docs.indesit.eu
• Using QR Code
• Alternatively, contact our echnical Assistance Service (See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product’s identication plate.
xxxxxxxxxxxx xxxx