Integral LED ILRC005 User Manual
Displayed below is the user manual for ILRC005 by Integral LED which is a product in the Lighting Accessories category. This manual has pages.
Related Manuals
IP63
Integral LED is a division of
Integral Memory plc London NW10 0UF
www.integral-led.com
Integral LED Single Colour
Remote Control and Receiver
ILRC005
WARNING
DO NOT CONNECT THE RECEIVER TO A MAINS SUPPLY.
THE RECEIVER MUST ONLY BE CONNECTED
TO A SUITABLE 5V-24V CONSTANT VOLTAGE LED DRIVER.
IMPORTANT NOTICE
• This product should be installed according to the instructions
in this guide and by a qualied electrical installer.
• All electrical work must be completed in accordance with
the latest IET wiring regulations (formally IEE) for the UK or
in accordance with all applicable regulations and laws in the
country in which it is being installed.
• Switch OFF power at the mains before installing the product.
• Always disconnect or switch o the power supply before
making any adjustment to the wiring.
• Observe the operating temperature of the product:
-30°C to +80°C
1. Introduction
2. Specications
INTRODUCTION
The Integral LED Single Colour Remote Control and Receiver
are designed to work with the Integral LED Single Colour
Strip. You will be able to adjust the brightness level of your
strip by using the supplied remote control.
1
LED Dimmer/ Receiver:
• Power Input: DC5V - DC24V
• Max Current Load: Max 10A
• IP Rating: IP63
• Max Output Power:
120W (12V) / 240W (24V)
• Brightness Grade: 256 levels
• Brightness Shortcut: 6 levels
• Working Temperature: -30°C to 80°C
• Dimension: 87x21x8.5mm with
120mm AWG16 Red / Black cables
at both ends
• Weight (N.W.): 19g
Total Weight (G.W.): 42g
RF Remote:
• Working Voltage:
3V (battery CR2025)
• Working Frequency: 433.92MHz
• PWM Frequency: 1 KHz
• Remote Distance:
within 15M in an open area
• Working Temperature: -30°C to 80°C
• Dimension: 40x86x6.5mm
• Weight (N.W.): 16g
4
1 year warranty
C. Remote control operating instructions
1
2
4
5
3
Fig. 2
1. Turn On/ Standby
Press ‘I’ key to turn ON unit or press ‘O’ key to turn OFF. On
power up the unit will automatically restore to the previous
brightness setting.
2/3. Brightness Adjustment
To adjust LED brightness, Press (BRIGHT+) to increase
brightness or press (BRIGHT-) to reduce brightness.
4. Brightness Shortcut keys
Shortcut key to 100%, 80%, 60%, 40%, 20% or 10%
brightness.
5. Remote Controller Indicator
The blue LED will ash when the remote control is operated.
The remote control uses RF (Radio Frequency); therefore it is
not necessary to aim the remote control directly at the LED
Dimmer/ Receiver.
2 3
Functions and Operating Instruction
A: Please note
a) The LED Dimmer/ Receiver operates on 5V to 24V DC (Ensure
that the LED DRIVER and LED STRIP operate at the same
voltage)
b) The LED Dimmer/ Receiver only supports CONSTANT VOLTAGE
LED DRIVERS
c) Ensure that the LED DRIVER is suitable to power the length and
type of LED
d) For proper operation with the remote control. Do NOT enclose
the LED Dimmer/ Receiver in metal e.g. metal trucking
e) Ensure that the LED Dimmer/ Receiver unit is installed in a
good heat dissipation environment to avoid overheating. Keep
the unit away from moisture.
B. Pairing New Remote
To pair a new remote control:
1). Turn OFF the mains power to the LED DRIVER and turn ON
after 5 seconds.
2). Press the ‘100%’ and ‘60%’ keys simultaneously within 5
seconds of power ON, the indicator will ash white 3 times to
conrm the command has been accepted, the LED Dimmer/
Receiver will now function with the new remote control. Only
the last three paired remote controls will be recognised.
OPERATING INSTRUCTIONS
A. Remote Battery
Please remove the battery installation tag before use. The
remote control uses a CR2025 cell battery; it can last for up to 2
years with normal usage.
B: Wiring
The LED Dimmer/ Receiver is wired in between the LED DRIVER
and LED STRIP. Install the LED Dimmer/ Receiver in accordance
with the wiring diagram (g 1). Please pay attention to polarity.
RED = positive (+), BLACK = negative (-). Ensure that the mains
power is OFF and cannot be connected unexpectedly during
installation.
C: The LED Dimmer/Receiver Status Indicator
The LED Dimmer/Receiver has output short circuit, overload and
overheat protection function, if the LED Dimmer/ Receiver stops
working please check the circuit for a short circuit or overload.
The full colour status indicator - displays all working statuses
of the controller. It indicates dierent functions as below. The
controller will automatically recover from the protection mode
when a good working status is restored.
Fig. 1
Blue Normal working
White Flash – Short Single New command received
Yellow Flash – Long Single Reached brightness limit
Red Blinking Overload/short circuit protected
Yellow Blinking Overheat protected
DC 5V-24V DC 5V-24V(Red)+
(Black)-
(Red)+
(Black)-
+
One remote per device.
Up to three remotes per device.
One remote to control multiple devices.