Table of Contents
Interline Aruba User Manual
Displayed below is the user manual for Aruba by Interline which is a product in the Above Ground Pools category. This manual has pages.
Related Manuals
ARUBA
OVAL POOLS
ASSEMBLY INSTRUCTIONS
UNIVERSAL INSTRUCTIONS
BRACED OVAL POOLS
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND THOROUGHLY BEFORE
STARTING GROUND PREPARATION AND POOL ASSEMBLY.
DOING SO WILL PREVENT PROBLEMS.
Oval Pool: General informaition -----------------------------------
1) Selection pool site -----------------------------------------------
2) Ground preparation ----------------------------------------------
3) Assembling side vertical,Horizontal support and brace-
4) Drawing pool shape ----------------------------------------------
5) Connecting tension straps --------------------------------------
6) Positioning assembled oval parts -----------------------------
7) Assembling bottom rail ------------------------------------------
8) Installing wall -------------------------------------------------------
9) Build an earth mound(Cove) -----------------------------------
10) Through the wall skimmer --------------------------------------
11) Liner installation ---------------------------------------------------
Please refer to "Assemble TopSeat , Vertical and Cover" of an attached sheet.
12) Filling the pool -----------------------------------------------------
13) Helpful information -----------------------------------------------
14) SAFETY RULES --------------------------------------------------
BRACED OVAL Parts List (#A OVAL CARTON) --------------
1
1
2
3
5
7
7
8
8
9
9
9
10
10
10
11
Page.
Do not start the installation of your pool unless you have
an entire day to finish the work.
Do not try to set up your pool on a windy day.
The wall will be difficult or even impossible to handle.
An average pool needs 2 or 3 people for
installation.
The following tools and materials are needed.
Shovel
Marking
Pencil
Masking
Tape
Rake
Chalk or
Flour
Plastic Tape
Earth Roller
String
Hammer &
Nails
Sand
2"x4" Board
Screwdriver
Tamping Tool
Pegs and
Stakes
Carpenter's
Level
Measuring Tape
Patio Block
Open the cartons and remove all parts except steel wall and liner.
Before pool assembly, you must identify, count and check all parts for
assembly by parts list. Familiarize yourself with all of the parts. Refer
to the parts list.
a) The site must be large enough to accommodate the pool with
plenty of area around it for pool accessaries, chairs, tables etc.
b) Determine where your filtration and skimmer will be located.
It must be connected to a grounded 110 volt electrical outlet,
with a G.F.I. (Ground Fault Interrupter)
c) The pool must be in reach of your water supply. Although the
water should not be drained, but kept clean through filtration and
chemicals, there should be drainage facilities near in case of need.
d) Perimeter area of ground must be absolutely level and firm. All
grass and sod under entire pool area must be dug out to avoid
unpleasant odors from decomposition under the pool due to lack of
air. Remove sharp objects, stones, twigs, pebbles, roots, etc.
They may damage the liner. If the ground has been treated with
chemicals or weed killer allow two weeks before setting up the pool.
Do not set up the pool on concrete, asphalt, tar paper, peatmoss,
sand, gravel, or where nut grass has been planted.
Poorly prepared ground could allow certain weeds or grass to grow
through the liner. Liner is not warranted against this. If ground is
uneven in perimeter area, dig out the high spots. Do not build up the
low side by padding it with earth. The weight and movement of the
water will pack down the fill causing the pool to sink. Inside
perimeter of pool (the area inside of the frame and wall) can be
leveled with 1" or 2" of sand raked and rolled smooth.
1) SELECTION OF POOL SITE
Before starting the installation, the following points are
important;
FAILURE TO OBSERVE ANY OF THE ABOVE INSTRUCTIONS
WILL VOID WARRANTY.
GENERAL INFORMATION
Before attempting to set up the pool, read the entire
instructions. There are certain areas in the instructions that are
extremely important to follow exactly as written and/or pictured.
Any deviation from these instructions voids warranty of the pool
and could cause bodily harm or damage to your property.
SIFTED EARTH OR SAND NEEDED
PER EACH SIZE POOL AS FOLLOWS:
CAUTION:
16' x 12' 26 cubic feet 0.79cubicM
34 cubic feet 0.96cubicM
42 cubic feet 1.19cubicM
20' x 12'
24' x 12'
1
POOL SIZE Wall Length Top Sheet
mm ft in. Q'ty
1612 13,855 45 5 4/8 12
2012 16,364 53 8 2/8 14
2412 18,873 61 11 16
a) Mark off your pool area by driving stakes. Have a helper hold a tape measure or a string and mark off the pool perimeter using flour or
chalk. Remove sod inside the pool area to a distance of 1 feet beyond dimensions shown in the plot layout around entire perimeter of
pool.
b) Remove all grass from within the entire pool area. It is not enough to just cut the grass. The sod must be removed.
c) Two or three inches of sand is the best for your liner. Using sand eliminates the necessity to level inside of frame area except where
exceptionally high or low areas exist.
These areas should either be dug or filled in. This does not mean the perimeter or frame area. That area must be firm and level by digging
only.
d) Do not fill low spots in the area where pool wall will rest. as setting may cause your pool to become out of level.
Making sure pool bottom is flat.This is a must.
e) If your site is not on firm soil, use 2" patio blocks for the base of the wall Care should be taken to center a patio
block under each bottom plate. The top of the patio blocks should be flush with the prepared ground surface.
2) GROUND PREPARATION
The preparation of the ground is the most important step in the installation of the pool.
18' 1" (48" Wall)
18' 1" (48" Wall)
18' 1" (48" Wall)
18' 6-2/8" (52" Wall)
18' 6-2/8" (52" Wall)
18' 6-2/8" (52" Wall)
24x12
20x12
(4847mm)
15' 10-7/8"
(6083mm)
(7319mm)
19' 11-4/8"
24' 1/8"
11' 10-1/8"
(5645mm)
(3611mm)
(5511mm)
(5511mm)
(3611mm)
11' 10-1/8"
(5645mm)
(5511mm)
(5645mm)
(3611mm)
11' 10-1/8"
16x12
3
Use #0104PACK Oval frame bolt package.
Use #0105(#0106)PACK Strap bolt package.
3) ASSEMBLINGSIDE VERTICAL, HORIZONTAL SUPPORT AND BRACE
P.No.0513
1/4" x 1/2" Truss Head Screw
P.No.0923
P.No.0611
1/4 Nut
P.No.3313 Side Vertical For 48"
P.No.3314 Side Vertical For 52"
The Figure which looked at attachment of
Side Upper Joint from down.
P.No.0345
5mmx40 Sheet Metal Screw
Resin Side Upper Joint
P.No.3177
(Packed #3 Package)
40mm
P.No.0345
5mmx40 Sheet Metal Screw
P.No.4103 Brace For 48"
P.No.4104 Brace For 52"
from inside, Do not fasten tightly.
Connect brace to side vertical.
put 1/4" nut from inside, Do not fasten
Washer from outside then put M8 nut from insaide AND
1/4"X1/2" truss head screw from outside then
Washer from outside then put M8 nut
Connect side vertical to horizontal support.
Put M8x20 hex head bolt with Plain
Put M8x20 hex head bolt with Plain
STEP2;
STEP1;
tightly.
1/2
P.No.0611
1/4in Nut STEP2
53 1/8" (1348mm)
55 3/4" (1414mm)
52 3/8" (1331mm)
49 1/8" (1248mm)
53 7/8" (1367mm)
49 3/4" (1264mm)
P.No.4104 Brace For 52"
P.No.4103 Brace For 48"
P.No.5236 Horizontal Support For 48"
P.No.5237 Horizontal Support For 52"
P.No.3314 Side Vertical For 52"
P.No.3313 Side Vertical For 48"
4
Connect brase to horizontal support.
Washer from outside then put M8 nut
Put M8x20 hex head bolt with Plain
from inside, Do not fasten tightly.
STEP4;
Fasten all bolts and screws tightly.
M8x20 hex head bolt.- two sets each for side
vertical to horizontal support, brace to side vertical
and brace to horizontal support.
#12X3/4 Sheet Metal Screw two sets each for braceto
side vertical.
P.No.0923
P.No.0923
P.No.0923
M8 x 20 Hex Head Bolt
M8 x 20 Hex Head Bolt
M8 x 20 Hex Head Bolt
P.No.0423
P.No.0423
P.No.0623
P.No.0623
M8 Nut
M8 Nut
P.No.7224
End Strap
Plain Washer
Plain Washer
P.No.0513
1/4" x 1/2" Truss Head Screw
P.No.5236 Horizontal Support For 48"
P.No.5237 Horizontal Support For 52"
STEP3;
P.No 3233
5/8" Side Lower Rail Joint - For 1" & 6 Frame
P.No.3222
1" Side Lower Rail Joint - For All other Frame
20mm
M8 x 20 Hex Head Bolt
P.No.0923
M8 Nut
P.No.0623
3-1) ASSEMBLING TENSION STRAP.
STEP;5
Refer page-7 "5) Connecting tention straps."
Attach End strap to Holizontal support, Put
to determine kind of straps.
M8 Nut from bottm. Put all bolt and tighten up.
M8x20 hex head Bolt from top and put
P.No.0623
M8 Nut
Plain Washer
P.No.0423
STEP4
STEP3
STEP1
18mm
P.No.0341
#12x3/4 Sheet Metal Screw
4) DRAWING POOL SHAPE
Please Draw a line with seeing the picture of each pool size.
(618mm)
2' 3/8"
(1806mm)
5'11-1/8"
5' 7-5/8"
(4847mm)
16x12
5'11-1/8"
2' 3/8"
(3611mm)
(618mm)
11' 10-1/8"
(1236mm)
(1717mm)
15' 10-7/8"
(1806mm)
4' 5/8"
(7319mm)
24' 1/8"
(618mm)
2' 3/8"
4' 5/8"
(1236mm)
4' 5/8"
(4232mm)
13'
10-5/8"
(1236mm)
12' 2"
(3708mm)
(1806mm)
5' 7-5/8"
5'11-1/8"
(3611mm)
11' 10-1/8"
5'11-1/8"
(618mm)
2' 3/8"
(1806mm)
(1717mm)
24x12
5
X Point
Wall
(618mm)
(1806mm)
5'11-1/8"
11'
11-3/4"
(3650mm)
2' 3/8"
11' 10-1/8"
5'11-1/8"
20x12
2' 3/8"
(618mm)
(1717mm)
(1806mm)
8' 1-3/8"
(2472mm)
4' 5/8"
5' 7-5/8"
(1236mm)
Side Vertical
19' 11-4/8"
(6083mm)
(3611mm)
IMPORTANT:
See "7) POSITIONING ASSEMBLED OVAL
PARTS."
Do not fill back hole at this point.
Digging holes;
Dig holes for each horizontal support as shown right. inside of pool
from "X" point 12 1/2" length. Dig holes where center of patio blocks
can be placed at 41" from "X"point for 48" height wall,44" for 52"
height wall,
width is 5" depth is 2". Dig holes accordingly depend on shape of
concrete blocks or patio blocks at outside of horizontal supports.
6
15" (380mm)
X Point
5"
2"
(127mm)
(50mm)
Case 52" Wall 44" (1117mm)
Case 48" Wall 41" (1041mm)
7
P.No.0923
P.No.0923
M8 x 20 Hex Head Bolt
M8 x 20 Hex Head Bolt
P.No.0623
P.No.0623
M8 Nut
M8 Nut
Top seat temporally placed should be removed before
proceeding to next step.
Note:
All Bolts to be inserted from the top side, Nuts to be
inserted from undernerath Tension straps.
6) POSITIONING ASSEMBLED OVAL PARTS.
Set all oval parts on the right position, Check(A)
length(distance between horizontal supports). Put
top seat on top of side upper joint temporally as
shown figure. Then check a-b,c-d is straight and
level. if not, adjust accordingly.
Put Pressure plate by Using #12x3/4
SheetMetal Screw after Positioning
Assembled oval parts.
This end should be connected
to horizontal support.
End strap
End strap; 7224 . Those should be used for the end.
Middle strap; 7254, 7244, 7264 or 7285. Those should be
used for the middle.
Connect type(B) strap(s) to already assembled type(A) straps.
using five sets of M8x20mm hex headed bolt and M8 nut.
Use #0106.PACK Strap Bolt Package
Use #0105.PACK Strap Bolt Package
5) CONNECTING TENSION STRAPS
Middle strap
7224 - 2pieces 16x12 - 1straps.
7254 - 1pieces 20x12 - 2straps.
24x12 - 3straps.
Quantity per set. Number of sets per pool.
12' Base Oval Pools
Combination of Strap Set
Length of Tension Straps.
Parts No. Type Length(in) Length(mm)
7224 End 55-1/8" 1400
7254 Middle 32-7/8" 835
20mm
18mm
P.No.0341
#12x3/4 Sheet Metal Screw
P.No.6254
Pressure plate
d
b
A
Note:
As shown below, put concrete block underneath the outside
of horizontal support assembled.
a
c
Pool Size (A)Length(in) (A)Length(mm)
16x12 4' 5/8" 1236
20x12 4' 5/8" 1236
24x12 4' 5/8" 1236
List of (A) Length
Bring the wall close to the bottom rail.
Make sure there is nothing in the bottom rail before inserting the wall. If there is
earth or something is in the bottom rail,take out it accordingly.
Begin to insert end of wall into bottom rail. One person unwinding wall (wall
should be on a plywood base for ease of rotating) while the other person is
feeding wall into slot of bottom rail around entire pool.
As you unwind the wall and insert it into the assembled bottom rails, temporarily
place top rail sections on top of the wall. This will help to prevent the wall form
bending or falling over.
Should the wall be either too short or too long,Adjust bottom rails,The
circumference of bottom rails can be adjusted slightly by equally tapping
outward or inward at the each lower joint until the wall ends meet.
Bring the two open ends of the wall together as shown above.
This is one of the most important steps in assembling the pool. Pay close
attention to the following points.
There is an up and down side on steel wall. Locate the skimmer cutouts
which are near the outside end of the wall. These cutouts must be at the
TOP even if you will not be using these cutouts .
Place coiled wall near bottom rail one section open.
8) INSTALLING WALL
It is practical if two people work together; one inside and one outside of the
pool.
Due to the weight of wall,some bending will occur in the top and bottom corrugation.
because the wall is built to flex. Simply bend those sections back before inserting wall in
top or bottom rail.
Use Wall Joint Bolt Package packed in a Wall Carton.
Bottom rails between the horizontal supports are set up by inserting each end of bottom rail into side lower joint,Insert the bottom rails around the entire
perimeter using lower joints on the circular portion of the pool.Leave one section open that will be nearest to where you will locate your filter.
Before proceeding to the next step, place a large amount to sifted earth in the middle of the circle. (see chart for the amount on the first page.)
Sifted earth should not contain any pebbles.
Place a patio block under each lower joint around curved area.Make sure top of patio block is flush with ground surface and top of horizontal support.
Before proceeding, remove the steel wall from carton and stand on a 3'x3' board inside pool area as shown at down. Put the liner, (leaving it in the
carton) inside pool area.
7) ASSEMBLING BOTTOM RAIL
Step 4:
STEP 1:
STEP 3:
Note:
STEP 2:
STEP
1:
STEP
2:
8
P.N.-0513
1/4 x 1/2in Truss Head Screw
1/2
P.N.-0611
1/4in Nut
WALL
WALL
NUT
INSIDE OF POOL
BOLT
REINFORCING
WASHER
P.N.-0411
1/4in Reinforcing Washer
φ 1 3/8
Wall
CURVED AREA
CURVED AREA
SIFTED
EARTH
SIFTED
EARTH
LINER
DO NOT FASTEN THE WALL WITHOUT USING THE REINFORCING
WASHERS ! FAILURE TO USE REINFORCING WASHERS AS
INSTRUCTED WILL CAUSE WALL TO SPLIT WHEN POOL IS FILLED.
THIS CAN CAUSE SERIOUS PROPERTY DAMAGE AND/OR BODILY
INJURY.
INSERT THE SCREWS FROM INSIDE OF WALL.
NUT MUST BE FASTENED FROM OUTSIDE OF
WALL.
* Reinforcing Washers must be on INSIDE and OUTSIDE of wall.
* Insert the screws from INSIDE of the wall.
* Insert and fasten screws from hole to hole down to the bottom
of the wall.Do not fasten tightly before insert all screws.
* Fasten all screws tightly.
* Do not leave any open holes.
* Cover all the screw heads with strip of fabric tape.
* Check the level of the top of the wall,if more than 2" off level ,
Rework the ground to achieve levelness.
Unfold the liner inside the metal wall. Carefully spread it out on
the ground. The seam around the bottom of the liner should be
well up the earth mound. Do this evenly all around pool.
Remove your shoes. The liner should never be forcefully pulled
or dragged, especially when it holds water, even only 1/2".
When you enter the pool during installation, use a ladder other
than a pool ladder.
Make sure the legs rest on a strong flat board
Open the liner carton carefully by removing the tape. (Do not cut
open carton.)
For untirusting, All edges of cut out have to be covered by vinyl
tape or rusting paint.
Begin the installation of the through the wall skimmer. Follow
separate skimmer installations.
At one point during the installation of the skimmer, you have to
install the liner. The skimmer installation will tell you when.
Complete the installation of the liner as described next. Then
finish the skimmer installation.
Build a mound 6" high and extending 8 to 10" on the ground
around the inside of the pool wall. Pack the earth gently but
firmly.
9) BUILD AN EARTH MOUND(cove)
The earth mound must be built right. you must rebuild the earth mound each
time you set up the pool. Water pressure can force the liner out under the
bottom rail. If this is not done.This could cause damage to the liner and void
warranty. The earth mound will prevent this from happening.
11) LINER INSTALLATION
10) THROUGH THE WALL SKIMMER
Remove top rail temporarily placed.
Lift the side of the liner over the top of the wall. Form a collar
approximately 3" down the outside of the wall and temporarily tape
it, to the outside of the wall using masking tape at intervals of 3'.
Take the plastic edging and clip it over the liner and the top of the
wall. The ends of each section of edging should touch each
other. The edging forms a full circle all around. Cut off excess
plastic edging
If the liner does not fit evenly around the pool.
Remove the masking tape gently from the collar of the liner and wall. Smooth
out all wrinkles on the bottom of the liner. There may be extra material around
the side. Spread it evenly all around the side of the pool. There may be extra
material in height.
IMPORTANT:
Step 2:
Step 1:
CAUTION:
Step 1:
Step 3:
Step 4:
4)
To keep the water clean and protect your liner from being damaged it is
best to cover hose end(s) with several layers of rags.
3)
Set as many hoses as you want to help speed up filling time. The pool
holds a considerable amount of water (ie;18' round pool holds 7650
gallons.).
2)
Measure all around the pool, from the TOP RAIL down to WATER
LEVEL. This level SHOULD NOT VARY MORE THEN ONE INCH.
An unleveled condition will cause overstress of the pool wall and frame.
Remove excess soil as required to establish a level frame and bottom
rail condition.
See " ASSEMBLY OF BOTTOM RAILS "
1)
INSPECT BOTTOM RAILS-make sure they are not scalloped, see
detail at right. If rails scallop, pull outward at the bottom of the
verticals to allow wall and rails to assume natural shape.
By using a string and small weight, check each vertical.To see that they
stand straight.
Be sure each vertical stands perfectly straight.
IMPORTANT: STOP FILLING POOL AT 1 FOOT DEPTH
When pool is completely assembled and ready for water, run water into
the pool. Wrinkles in pool liner should be smoothed out as water is
added for easier maintenance.
The hard work is all behind.
Now the fun begins.
12) FILLING THE POOL
CAUTION:
Do not attempt to straighten liner after you begin to fill with water.
Severe damage could be caused and You will void warranty.
5)
When desired water level is reached, turn on your filter.
(Follow separate instructions provided with your filter.)
9
1/4in Reinforcing Washer
1/4in Reinforcing Washer
1/4in Reinforcing Washer
1/4in Reinforcing Washer
INSIDE OF POOL
INSIDE OF POOL
2in
6in
Please refer to "Assemble TopSeat ,
Vertical and Cover" of an attached sheet
Leaks in skimmer and filter connections must be stopped.
A constant drip of chlorinated water on metal will corrode the metal.
a)
Proper filtering and chemical treatments should not make it necessary
to change the pool water.
Your pool dealer will advise you of the proper procedure.
To estimate the amount of chemicals needed here is the approximate
water content of the pool based on full capacity:
To help keep the pool clean and child proof, a pool cover should be on
the pool whenever it is not in use. This also reduces loss of water and
chemicals.
To keep the pool in working condition check the following operation.
2.
1.
13) HELPFUL INFORMATION
1.
14) SAFETY RULES
Read your instructions and safety rules carefully. If you do not follow
the safety rules someone could be injured or damage could occur.
2. Plan carefully where you are going to put your pool. It must be close to
a water source for filling. Also think about draining your pool.
3. Never let anyone swim alone. Children must be carefully watched. For
added safety, install a convex type mirror above pool to give full view
of interior.
Available at most mirror dealers.
4. Do not let anyone rough-house in or around your pool. The pool area
and decks can be slippery. Someone could be badly injured. You can
prevent this type problem by enforcing the safety rules.
5. Always keep the water clean and sanitary. Dirty water can be
dangerous. Use your filter system. Follow instructions included with
your filter. Also use water purifying chemicals as needed.
6. DO NOT DIVE OR JUMP INTO YOUR POOL. THE POOL IS NOT
DESIGNED FOR DIVING OR JUMPING !
7. Remove ladders when there is no adult to watch the pool.
Remove anything else that can be used get into the pool.
Use a cover if the pool is not in use for a long period of time.
SAFETY DECALS CAN BE AFFIXED TO A CLEAN,DRY,
SMOOTH SURFACE SUCH AS THE VINYL LINER,TOP
SEAT THAT HAS SMOOTH FINISH. THEY MUST BE
PLACED THAT THEY ARE EASILY SEEN.
Do not empty your pool in spring. Filtration and chlorination will
remove all impurities. Leaves and other matter should be skimmed or
vacuumed out of the pool.
The pool should be left up and filled year round properly winterized and
covered with a good cover. The water level must be lowered to about
6" below the lowest skimmer opening if your area is subjected to be
below freezing temperature. All pool leaks must be repaired before
winter.
d)
c)
b)
Jumping and diving into a ASAHI CHEMICAL's Pool is STRICTLY FORBIDDEN.
It is your responsibility as the owner of the pool to do the following:
Do not locate pool near objects that would entice diving i.e. garages, tree, porches, etc.
Do not let anyone use your pool unless they are fully aware of the DO NOT DIVE OR JUMP notice.
Do not promote horse play or other activities that would cause injuries.
Do not allow people to sit or walk on the top seat of the pool.
IT IS YOUR RESPONSIBILITY AS A POOL OWNER TO INSURE THE SAFETY OF WHOMEVER USES THE POOL
NOT THE MANUFACTURER.
READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING YOUR POOL.
Read through all instructions completely and familiarize yourself with all pool parts and accessories before pool assembly.
Damage may be done if all instructions are not carefully followed, and in such cases, will void manufacturer's warranty.
When assembling pool, read through what you must do for each step, then proceed.
WARNING
THIS POOL IS DESIGNED FOR SWIMMING ONLY. IT IS NOT INTENDED FOR DIVING OR JUMPING.
FOR A MAXIMUM OF SWIMMING FUN, BE SURE TO FOLLOW ALL SAFETY RULES WHEN USING ANY SWIMMING POOL.
Pool Size Capacity
gallons
Pool Size Capacity
gallons
16x12x52 5,050
20x12x52 6,585
24x12x52 8,117
16x12x48 4,661
20x12x48 6,079
24x12x48 7,493
10
If there is sign of corrosion on pool wall drain pool
immediately, and replace it.
If there is sign of corrosion on other pool parts, sand off the rust.
paint with rust resistant paint.
PERMANET INJURY OR DEATH CAN RESULT.
DANGER
DO NOT
DO NOT
JUMP
DIVE
BRACED OVAL PARTS LIST
RG08-A (48") CARTON
Parts No. Discription
16x12x48
20x12x48
24x12x48
3313 Side Vertical (48" Wall) 246
4103 Brace (For 48" Wall) 246
5236 Horizontal Support (48" Wall) 246
6254 Pressure plate L=680mm(26-3/4") 246
7224 End Strap L=1400mm(55-1/8") 246
7254 Middle strap L=835mm(32-7/8") 1 2 3
7244 Middle strap L=929mm(36-5/8")
7264 Middle strap L=1405mm(55-3/8")
7285 Middle strap L=1287mm(50-5/8")
0104.PACK Braced Oval Frame Bolt Package 123
0105.PACK Strap Bolt Package 1 2 3
0106.PACK Strap Bolt Package
RG08-A (52") CARTON
Parts No. Discription
16x12x52
20x12x52
24x12x52
3314 Side Vertical (For 52" Wall) 246
4104 Brace (For 52" Wall) 246
5237 Horizontal Support (For 52" Wall) 246
6254 Pressure plate L=680mm(26-3/4") 246
7224 End Strap L=1400mm(55-1/8") 246
7254 Middle strap L=835mm(32-7/8") 1 2 3
7244 Middle strap L=929mm(36-5/8")
7264 Middle strap L=1405mm(55-3/8")
7285 Middle strap L=1287mm(50-5/8")
0104.PACK Braced Oval Frame Bolt Package 123
0105.PACK Strap Bolt Package 1 2 3
0106.PACK Strap Bolt Package
Contents of each Bolt Package.
0104.PACK Braced Oval Frame Bolt Package
0923 M8 X 20 Hex Head Bolt 13
0423 10.5mm X 21mm X 2.0mm Plain Washer 13
0623 M8 Nut 13
0341 #12 x 3/4 Sheet Metal Screw 8
0513 1/4" x 1/2" Truss Head Screw 5
0611 1/4" Nut 5
0105.PACK Strap Bolt Package
0623 M8 Nut 22
0923 M8 X 20 Hex Head Bolt 22
0106.PACK Strap Bolt Package
0623 M8 Nut 27
0923 M8 X 20 Hex Head Bolt 27
14