KitchenAid KEBDS 90020 User Manual
Displayed below is the user manual for KEBDS 90020 by KitchenAid which is a product in the Cooker Hoods category. This manual has pages.
Related Manuals
Instructions for use
Important instructions for safety 4
Installation 6
Safeguarding the environment 6
Troubleshooting guide 7
After-Sales Service 8
Cleaning 8
Maintenance 9
Material supplied 10
Installation - preliminary assembly instructions 11
Installation dimensions 12
Installation - assembly instructions 13
Description and use of hood 14
These instruction shall be available on website www.kitchenaid.eu
4
YOUR SAFETY AND THAT OF OTHERS IS
HIGHLY IMPORTANT.
This manual and the appliance itself provide
important safety warnings, to be read and
observed at all times.
This is the attention symbol, pertaining to
safety, which alerts users to potential risks to
themselves and others.
All safety warnings are preceded by the attention
symbol and the following terms:
indicates a hazardous situation which, if not
avoided, will cause serious injury.
indicates a hazardous situation which, if not
avoided, could cause serious injury.
All safety warnings specify the potential
danger/warning to which they refer and indicate
how to reduce the risk of injury, damage and
electrical shock resulting from incorrect use of the
appliance. Comply with the following instructions:
• Installation or maintenance must be carried out
by a specialized technician, in compliance with
the manufacturer’s instructions and local safety
regulations.
Do not repair or replace any part of the
appliance unless specifically requested in the
user manual.
• The appliance must be disconnected from the
power supply before carrying out any
installation work.
• Earthing of the appliance is compulsory. (Not
necessary for class II hoods identified by the
symbol on the specifications label).
• The power supply cable must be long enough to
permit connecting the appliance to the mains
socket outlet.
• Do not pull the power supply cable in order to
unplug the appliance.
• The electrical components must no longer be
accessible to the user after installation.
• Do not touch the appliance with any wet part of
the body and do not operate it when barefoot.
• This appliance may be used by children older
than 8 years of age and by persons with
reduced physical, sensory or mental capacities
or with inadequate experience and knowledge
only if they are supervised or if they have been
taught how to use the appliance in conditions of
safety and if they are aware of the dangers
involved. Children must not play with the
appliance. Cleaning and maintenance must not
be carried out by children, unless they are
supervised by adults.
• Do not repair or replace any part of the
appliance unless specifically indicated in the
manual. Defective parts must be replaced using
genuine parts. All other maintenance services
must be carried out by a specialized technician.
• Children must be supervised to ensure they do
not play with the appliance.
• When drilling through a wall or the ceiling, pay
attention not to damage electric connections
and/or pipes.
• The ventilation ducts must always discharge to
the outside.
• Exhaust air must not be vented through a flue
used for removal of fumes produced by
appliances burning gas or other fuels, but must
have a separate outlet. All national regulations
governing extraction of fumes must be
observed.
• If the hood is used together with other
appliances operating on gas or other fuels, the
negative pressure in the room must not exceed
4 Pa (4 x 10-5 bar).
For this reason, make sure the room is
adequately ventilated.
• The Manufacturer declines any liability for
improper use or incorrect setting of the
controls.
• Regular cleaning and maintenance is essential to
correct functioning and good performance of
the appliance. Frequently clean all encrustations
from dirty surfaces to prevent the accumulation
of grease. Regularly clean or replace the filters.
• Failure to observe the instructions for cleaning
the hood and replacing the filters may result in a
fire.
• The fume extractor hood must never be
opened without the grease filters installed and it
should be kept under constant supervision.
• Gas appliances must be used under the
extractor hood only with pans resting.
• When using more than three gas cooking points,
the hood should be operating at power level 2
or greater. This will eliminate heat congestion in
the appliance.
• Before touching the bulbs, first ensure that they
are cold.
• Do not use or leave the hood without its lamps
correctly installed - risk of electric shock.
• Wear work gloves for all installation and
maintenance operations.
WARNING:
DANGER:
Important instructions for safety
5
• The product is not suitable for outdoor use.
• When the hob is in use, accessible parts of the
hood may become hot.
• Never flame cook food (flambé) under the
appliance. Using free flames might cause fire.
• Do not leave frying pans unattended when
frying, as the frying oil may catch fire.
Scrapping of household appliances
• This appliance is manufactured with recyclable
or reusable materials. Dispose of it in
accordance with local waste disposal
regulations. Before disposing of it, make it
unusable by cutting off its power supply cable.
• For further information on the treatment,
recovery and recycling of household appliances,
contact your competent local authority, the
collection service for household waste or the
shop where you purchased the appliance.
KEEP THESE INSTRUCTIONS
Declaration of conformity
• This appliance has been designed, manufactured
and marketed in compliance with:
- safety objectives of the “Low Voltage” Directive
2006/95/EC (which replaces 73/23/EEC and
subsequent amendments);
- the ecodesign requirements of european
regulations n. 65/2014, and n. 66/2014 in
conformity to the european standard EN 61591
- the protection requirements of Directive “EMC”
2004/108/EC.
Electrical safety of the appliance can only be
guaranteed if it is correctly connected to an
approved earthing system.
Energy saving tips
• Switch ON the hood at minimum speed when
you start cooking and kept it running for few
minutes after cooking is finished.
• Increase the speed only in case of large amount
of smoke and vapour and use boost speed(s) only
in extreme situations.
• Replace the charcoal filter(s) when necessary to
maintain a good odour reduction efficiency.
• Clean the grease filter(s) when necessary to
maintain a good grease filter efficiency.
• Use the maximum diameter of the ducting
system indicated in this manual to optimize
efficiency and minimize noise.
6
After unpacking the appliance, check for any
damage caused during transport. In case of
problems, contact the dealer or the After-Sales
Service. To avoid any damage, it is advisable to only
remove the appliance from the polystyrene base
just before installation.
PREPARATION FOR INSTALLATION
this appliance is heavy; the hood should only
be lifted and installed by two or more people.
The minimum distance between the cooking pan
support on top of the cooker and the bottom of
the hood must not be less than 50 cm for electric
cookers and 65 cm for gas or mixed cookers.
Before installation also check the minimum
distances stated in the manual of the cooker.
If the installation instructions for the cooker specify
a greater distance between cooker and hood, this
distance must be observed.
ELECTRICAL CONNECTIONS
Make sure the power voltage specified on the
appliance rating plate is the same as the mains
voltage.
This information may be found on the inside of the
hood, under the grease filter.
Power cable replacement (type H05 VV-F 3 x 0.75
mm²) must be carried out by a qualified electrician.
Contact an authorized service centre.
If the hood is fitted with an electric plug, connect
the plug to a socket complying with current
regulations, located in an accessible place. If no
plug is fitted
(direct wiring to the mains), or if the socket is not
located in an accessible place, install a standardized
double pole power switch that will enable
complete
isolation from the mains in case of category III
overvoltage conditions, in accordance with wiring
rules.
GENERAL RECOMMENDATIONS
Before use
Remove cardboard protection pieces, transparent
film and adhesive labels from accessories.
Make sure the appliance has not been damaged
during transport.
During use
Do not place weights on the appliance, as they
could damage it.
Do not expose the appliance to atmospheric
agents.
WARNING:
Installation
Disposal of packing
The packing material is 100% recyclable and is
marked with the recycle symbol . The various
parts of the packing must be disposed of responsibly
and in full compliance with local authority
regulations governing waste disposal.
Disposal of the appliance
- This appliance is marked in compliance with
European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE).
- By ensuring that this appliance is disposed of
correctly, you can help prevent potentially
damaging consequences for the environment and
health.
- The symbol on the product or on the
accompanying documentation indicates that it
should not be treated as domestic waste but
must be taken to an appropriate collection
centre for the recycling of electrical and
electronic equipment.
Safeguarding the environment
7
The hood does not work
Make sure:
• There is not a power failure.
• A speed has actually been selected.
• The front panel is correctly hooked.
• The 9-pin connection is properly inserted. (Figure 1)
• The red reset button on the electrical system box is pressed. (Figure 2)
• In the 9-pin connection, make sure the wires are properly inserted in
the connector. (When connecting, pressing too hard could bend the
contacts). (Figure 3)
The hood does not extract sufficiently
Make sure:
• The selected speed is sufficient for the quantity of fumes and steam
present.
• There is enough ventilation to allow an air inlet.
• The carbon filter is not worn (Filter version hood).
• The exhaust air outlet pipe is free of obstructions.
• The extraction unit non-return valves are free to rotate. (Figure 4)
The hood stops during operation
Make sure:
• There is not a power failure.
• The differential thermal-magnetic switch (safety cutout) has not tripped.
The lamp does not work
• Check if the lamp needs replacing.
• Make sure the lamp is correctly fitted.
Fig. 1
Fig. 2
Fig. 3
Troubleshooting guide
Fig. 4
8
After-Sales Service
Before calling the After-Sales Service:
1. See if you can solve the problem yourself with
the help of the suggestions given in the
"Troubleshooting guide".
2. Switch the appliance off and back on again it to
see if the fault persists.
If after the above checks the fault still occurs,
get in touch with the nearest After-Sales
Service.
Always specify:
• A brief description of the fault;
• The exact type and model of the appliance;
• The service number (number after the word
"Service" on the rating plate), located on the
inside of the appliance. The service number is
also indicated on the guarantee booklet;
• Your full address;
• Your telephone number.
If any repairs are required, please contact an
authorised After-sales Service (to guarantee
that original spare parts will be used and repairs
carried out correctly).
Cleaning
• Do not use steam cleaners.
• Disconnect the appliance from the power
supply.
IMPORTANT: After carrying out hood or filter
cleaning, refit the front panel and filters, checking
correct installation and hooking, otherwise the
hood will not switch on.
IMPORTANT: Do not use corrosive or abrasive
detergents. If any of these products accidentally
comes into contact with the appliance, clean it
immediately with a damp cloth.
• Clean the surfaces with a damp cloth. If very
dirty, add a few drops of washing up detergent
to the water. Dry with a dry cloth.
IMPORTANT: Do not use abrasive sponges,
metallic scrapers or scouring pads, as they could
eventually spoil the enamelled surfaces.
• Use specific detergents for cleaning the
appliance and follow the manufacturer's
instructions.
IMPORTANT: Clean the filters at least monthly to
remove any oil or grease residuals.
IMPORTANT: Failure to carry out correct hood
cleaning or filter maintenance involves the risk of
fire. Therefore make sure to follow the
instructions.
The manufacturer declines any liability for damage
to the extraction unit, fires caused by improper
maintenance or failure to observe the above
instructions.
WARNING
9
Maintenance
• Use protective gloves.
• Disconnect the appliance from the power supply.
IMPORTANT: After carrying out hood or filter cleaning, refit the front panel and filters,
checking correct installation and hooking, otherwise the hood will not switch on.
GREASE FILTER
Its purpose is to retain the particles of grease produced by cooking.
It must be cleaned once a month (or when the filter saturation warning
system indicates this need) with non-aggressive detergents, by hand or in a
dishwasher at low temperature and with short cycle.
Cleaning in a dishwasher may cause discolouring of the metallic grease filter,
but its filtering efficiency is unaffected.
Grease and carbon filters must be fitted and removed while the air intake
panel of the hood is open. To carry out this procedure, press ON (T5).
Remove the front panel by pulling the top part of each side at the same
time. The panel will flip forwards, providing access to the grease filters
(Figure 5)
ACTIVATED CARBON FILTER (Filter Version only)
Its purpose is to retain the unpleasant odours produced by
cooking.
The carbon filter becomes saturated after more or less prolonged use
depending on the type of cooker and how often the grease filter is
cleaned. In any case the carbon filter must be replaced at least every four
months.
The carbon filter CANNOT be washed or regenerated.
The carbon filters can be inserted after removing the grease filters.
(Figure 6)
LIGHTING SYSTEM
Disconnect the appliance from the power supply.
IMPORTANT: Do not touch the neon with bare hands after prolonged
hood use with the lights switched on.
To replace the neon, proceed as follows (Figure 7):
1. Lift the extraction panel.
2. Disconnect the power supply (this operation can be carried out by
pulling out the plug, if accessible, or opening the switch, if provided for
during installation, or pressing the red reset button in the control box).
3. Remove the screws fixing the upper front.
4. Lift the upper front
5. Remove the burnt-out neon and replace it with one having the same
characteristics (Model T5 14W 860).
If the lighting does not work, make sure the neon is properly fitted before calling the After-Sales Service.
WARNING
WARNING
Fig. 5
Fig. 6
Fig. 7
10
Material supplied
Remove all the components from the packets. Check that all the
components are included. (Figure 8)
• Hood assembled with extraction unit, neon and grease filters
installed
• 2 Carbon filters
• Instructions for assembly and use
• Metal box containing the electronic components.
•2 Brackets
• 2 Screws Ø 3,5 x 9,5
• 4 Screws Ø M4 x 10
• 2 Washers
Fig. 8
11
Installation - preliminary assembly instructions
The hood is designed for installation and use in "Extractor Version" with
extraction to the outside or in "Filter Version" with internal
recirculation.
Install the hood away from very dirty areas, windows, doors and heat
sources.
IMPORTANT: Before connecting the air outlet flexible tube, make
sure the extraction unit non-return valves are free to rotate. (Figure 9)
Extractor Version (Figure 10)
Steam and fumes are expelled to the outside through an exhaust pipe
fixed to the connection flange.
The diameter of the exhaust must be equal to that of the connection
collar (150 mm).
In the horizontal part, the pipe must slope slightly upwards (approx.
10°) to convey the air to the outside more easily.
IMPORTANT: The extraction pipe is not supplied and must be
purchased.
IMPORTANT: If already installed, remove the carbon filters.
Filter Version (Figure 11)
The sucked air will be degreased and deodorised before being re-
conveyed in the room. To use the hood in this version it is necessary to
install an additional filtering system based on activated carbons.
IMPORTANT: The air recycled through the carbon filters is sent
through a duct that conveys the air on one side of the cabinet.
IMPORTANT: Check that air recirculation is facilitated..
Fig. 9
Fig. 10
Fig. 11
12
Installation dimensions
The hood must be installed in a cabinet having the characteristics indicated in the figure. (Figure 12)
IMPORTANT: The hood is designed and approved for use exclusively with KitchenAid gas, electric,
vitroceramic, induction hobs.
For gas hobs, the total max. power is 16.2 kW.
If the hood is used with gas hobs, the downdraft hood must be installed exclusively with external
extraction (extractor version) and the burners must be equipped with safety valves.
If the hood is used with gas hobs, when the hood is in the "ON" position the extraction flow could slightly
modify the distribution of the flame on the pot. In particular, if extraction is set to max. levels (power 3 or
4) make sure to privilege the non-frontal positions of the gas hob, for cooking with grills or pans with large
surface.
For hob installation, refer to the respective instruction manual.
IMPORTANT: A distance of at least 70 mm must be respected between the hob hole and the hood hole.
With installation of gas hobs, a distance of 100 mm between hood and hob is advisable.
Fig. 12
13
Installation - assembly instructions
The instructions given below in numerical order refer to the drawings in the "assembly instructions"
manual, containing the respective numbering.
1. Make a 842x100 mm rectangular hole behind the hob, to enable insertion of the hood.
IMPORTANT: Make sure the overall dimensions of the hood and hob are compatible with the cabinet
and therefore that installation is feasible.
Maintain a minimum distance of 70 mm from the hob.
Before making the hole, make sure the structure of the cabinet or other parts that could create
problems for correct installation are not present in the hood zone inside the cabinet.
2. Remove the extraction unit from the main body of the hood by undoing the 8 fixing screws.
3. Install the hood in the hole, inserting it from above.
4. Fix the 2 brackets (supplied) to the main hood body. Undo the 4 ØM4x10 screws already fitted on the
hood and fix the brackets.
IMPORTANT: Position the brackets so that a distance of 2 mm remains between the lower part of
the brackets and the bottom of the cabinet. This distance allows the hood to be pulled downwards at
the time of fixing, to ensure perfect adherence of the stainless steel frame to the worktop.
5. Fix the hood inside the cabinet, operating on the 2 brackets, using the 2 washers and 2 Ø3.5x9.5
screws supplied.
IMPORTANT: Before fitting the screws in the cabinet, make sure the product is perfectly
perpendicular to the worktop.
6. Fit the extraction unit, adjusting the air outlet to the required position upwards or downwards.
7. Make a 150 mm diameter hole in the cabinet for the air outlet ducting.
IMPORTANT: Locate the best position according to the particular conformation.
8. Fit the air outlet ducting.
IMPORTANT: The extraction pipe is not supplied and must be purchased.
Avoid drastic changes of direction.
Use a pipe in approved material and having a constant width of 150 mm for its entire length.
9. Connect the electrical connectors of the metal box to the hood (pushbutton panel connector, 9-pin
connector, neon connector) and the extraction unit to the metal box (6-pin connector).
10. Position the metal box containing the electronic components so as not to hinder the air outlet ducting.
11. Connect the hood to the power supply and press the red reset button on the metal box.
12. Press the ON button (T5) on the control panel to open the extraction panel, remove the hood
protection devices and lock the door.
14
Description and use of hood
(Figure 13)
1. Control panel
2. Front panel
3. Grease filters
4. Carbon filters (Filter Version only)
5. Lighting
CONTROL PANEL (Figure 14)
The hood has a "TOUCH" device for control of lights and speed.
For correct use, carefully read the instructions below.
•Button T1:
Delays hood switch-off, timing the set speed for a few minutes.
With this function, the hood switches off at the end of the time.
Operation times are as follows:
• extraction speed (power) 1: 20 minutes.
• extraction speed (power) 2: 15 minutes.
• extraction speed (power) 3: 10 minutes.
• extraction speed (power) 4: 5 minutes.
Press button T2 or T3 and the hood exits timed mode and the extraction speed (power) decreases or
increases depending on the button pressed. During the timing stage, the LED corresponding to the speed
blinks.
IMPORTANT: When operating the timer, the hood might switch to a lower intake speed (power)
before turning off, as on some speeds there is already a timing on the speed reduction itself.
•Button T2:
Decreases the active extraction speed (power) (4→3→2→1→OFF). The speed is displayed by lighting
up of the LED corresponding to the speed. Button T2 has no effect on extraction panel opening/closing.
•Button T3:
Increases the active extraction speed (power) (1→2→3→4). The speed is displayed by lighting up of
the LED corresponding to the speed.
IMPORTANT: (only for models fitted with a motor or a remote GME 22):
Suction speed 4 (power) is timed for 6 minutes, after which the hood will automatically switch to
suction speed 3 (power).
IMPORTANT: If the panel is closed (hood off), button T3 firstly operates extraction panel opening and
then sets the hood to extraction speed (power) 1.
•Button T4:
Switches on the light.
IMPORTANT: If the extraction panel is closed (hood off), button T4 firstly operates extraction panel
opening and then switches on the light.
Fig. 13
Fig. 14
15
•Button T5:
Opens (lifts) and closes (lowers) the extraction panel.
With the hood off and panel closed, button T5 firstly opens the extraction panel and then sets the hood
to extraction speed (power) 1.
With the hood on (at any speed) and panel open, button T5 firstly switches the hood off (also switching
off the lights, if on) and then closes the extraction panel.
IMPORTANT: Use the highest speed setting for particularly concentrated steam and fumes. It is
advisable to activate extraction 5 minutes before starting cooking and leave it on for about another 15
minutes at the end of cooking.
Additional information on operation
When removing the front panel for cleaning and maintenance operations, all electronic extraction and
movement functions are blocked.
Antipinching system: whenever an obstacle hinders closing of the Downdraft, closing stops and the
extraction panel goes up.
Grease filter saturation signalling
Every 40 hours of use, the hood signals the need for grease filter maintenance. Signalling occurs with all
the extraction speed (power) LEDs blinking at the same time.
Grease filter signalling reset: after carrying out grease filter maintenance, press button T1 for more than 3
seconds to reset the signalling.
IMPORTANT: Signalling is not displayed with the hood OFF, regardless of the position of the extraction
panel.
400010790008
Printed in Italy n
04/15
GB