Table of Contents
- Contents
- 1. Getting Started
- 2. NETGEAR ReadyNAS 102
- 3. NETGEAR ReadyNAS 104
- 4. NETGEAR ReadyNAS 202
- 5. NETGEAR ReadyNAS 204
- 6. NETGEAR ReadyNAS 212
- 7. NETGEAR ReadyNAS 214
- 8. NETGEAR ReadyNAS 312
- 9. NETGEAR ReadyNAS 314
- 10. NETGEAR ReadyNAS 316
- 11. NETGEAR ReadyNAS 422
- 12. NETGEAR ReadyNAS 424
- 13. NETGEAR ReadyNAS 426
- 14. NETGEAR ReadyNAS 428
- 15. NETGEAR ReadyNAS 516
- 16. NETGEAR ReadyNAS 524X
- 17. NETGEAR ReadyNAS 526X and 626X
- 18. NETGEAR ReadyNAS 528X and 628X
- 19. NETGEAR ReadyNAS 716X
- 20. NETGEAR EDA 500
- 21. Disks
- A. Defaults and Technical Specifications
- Factory Default Settings
- ReadyNAS 102 Technical Specifications
- ReadyNAS 104 Technical Specifications
- ReadyNAS 202 Technical Specifications
- ReadyNAS 212 Technical Specifications
- ReadyNAS 204 Technical Specifications
- ReadyNAS 214 Technical Specifications
- ReadyNAS 312 Technical Specifications
- ReadyNAS 314 Technical Specifications
- ReadyNAS 316 Technical Specifications
- ReadyNAS 422 Technical Specifications
- ReadyNAS 424 Technical Specifications
- ReadyNAS 426 Technical Specifications
- ReadyNAS 428 Technical Specifications
- ReadyNAS 516 Technical Specifications
- ReadyNAS 524X Technical Specifications
- ReadyNAS 526X Technical Specifications
- ReadyNAS 528X Technical Specifications
- ReadyNAS 626X Technical Specifications
- ReadyNAS 628X Technical Specifications
- ReadyNAS 716X Technical Specifications
- EDA 500 Technical Specifications
- Safety Warnings
NETGEAR ReadyNAS 426 User Manual
Displayed below is the user manual for ReadyNAS 426 by NETGEAR which is a product in the NAS & Storage Servers category. This manual has pages.
Related Manuals
ReadyNAS OS 6 Desktop
Storage Systems
Hardware Manual
Model
ReadyNAS 102, 104
ReadyNAS 202, 204, 212, 214
ReadyNAS 312, 314, 316
ReadyNAS 422, 424, 426, 428
ReadyNAS 516, 524X, 526X, 528X
ReadyNAS 626X, 628X
ReadyNAS 716X
EDA 500
April 2017
202-11206-10
350 E. Plumeria Drive
San Jose, CA 95134
USA
Support
Thank you for purchasing this NETGEAR product.You can visit www.netgear.com/support to register your
product, get help , access the latest do wnloads and user man uals, and join our comm unity.W e recommend that
you use only official NETGEAR support resources.
Conformity
For the current EU Declaration of Conformity, visit http://kb.netgear.com/app/answers/detail/a_id/11621.
Compliance
For regulatory compliance information, visit http://www.netgear.com/about/regulatory.
See the regulatory compliance document before connecting the power supply.
Trademarks
© NETGEAR, Inc., NETGEAR, and the NETGEAR Logo are trademarks of NETGEAR, Inc. Any non-NETGEAR
trademarks are used for reference purposes only.
2
ReadyNAS OS 6 Desktop Storage Systems
Contents
Chapter 1 Getting Started
Additional Documentation....................................................................................13
Setup Locationsetup location...............................................................................13
Suppor ted Operating Systems.............................................................................13
Supported Browsers............................................................................................14
Diskless Storage Systems...................................................................................14
Chapter 2 NETGEAR ReadyNAS 102
Front and Side Panels..........................................................................................16
Drive Bays............................................................................................................16
Rear Panel...........................................................................................................17
Status Information................................................................................................18
Power On and Shut Down....................................................................................19
Power On.........................................................................................................20
Preferred Shutdown........................................................................................20
Forced Shutdown............................................................................................20
Boot Menu............................................................................................................20
Chapter 3 NETGEAR ReadyNAS 104
Front and Side Panels..........................................................................................24
Drive Bays............................................................................................................24
Rear Panel...........................................................................................................25
Status Information................................................................................................26
Power On and Shut Down....................................................................................27
Power On.........................................................................................................28
Preferred Shutdown........................................................................................28
Forced Shutdown............................................................................................28
Boot Menu............................................................................................................28
Chapter 4 NETGEAR ReadyNAS 202
Front and Side Panels..........................................................................................31
Drive Bays............................................................................................................31
Rear Panel...........................................................................................................32
Status Information................................................................................................33
Power On and Shut Down....................................................................................34
Power On.........................................................................................................35
Preferred Shutdown........................................................................................35
Forced Shutdown............................................................................................35
Boot Menu............................................................................................................35
Chapter 5 NETGEAR ReadyNAS 204
Front and Side Panels..........................................................................................39
3
Drive Bays............................................................................................................39
Rear Panel...........................................................................................................40
Status Information................................................................................................41
Power On and Shut Down....................................................................................42
Power On.........................................................................................................43
Preferred Shutdown........................................................................................43
Forced Shutdown............................................................................................43
Boot Menu............................................................................................................43
Chapter 6 NETGEAR ReadyNAS 212
Front and Side Panels..........................................................................................46
Drive Bays............................................................................................................46
Rear Panel...........................................................................................................47
Status Information................................................................................................48
Power On and Shut Down....................................................................................49
Power On.........................................................................................................50
Preferred Shutdown........................................................................................50
Forced Shutdown............................................................................................50
Boot Menu............................................................................................................50
Chapter 7 NETGEAR ReadyNAS 214
Front and Side Panels..........................................................................................54
Drive Bays............................................................................................................54
Rear Panel...........................................................................................................55
Status Information................................................................................................56
Power On and Shut Down....................................................................................57
Power On.........................................................................................................58
Preferred Shutdown........................................................................................58
Forced Shutdown............................................................................................58
Boot Menu............................................................................................................58
Chapter 8 NETGEAR ReadyNAS 312
Front and Side Panels..........................................................................................61
Drive Bays............................................................................................................61
Rear Panel...........................................................................................................62
Status Information................................................................................................63
Power On and Shut Down....................................................................................64
Power On.........................................................................................................64
Preferred Shutdown........................................................................................65
Forced Shutdown............................................................................................65
Boot Menu............................................................................................................65
Chapter 9 NETGEAR ReadyNAS 314
Front and Side Panels..........................................................................................69
Drive Bays............................................................................................................69
Rear Panel...........................................................................................................70
Status Information................................................................................................71
Power On and Shut Down....................................................................................72
4
ReadyNAS OS 6 Desktop Storage Systems
Power On.........................................................................................................73
Preferred Shutdown........................................................................................73
Forced Shutdown............................................................................................73
Boot Menu............................................................................................................74
Chapter 10 NETGEAR ReadyNAS 316
Front and Side Panels..........................................................................................77
Drive Bays............................................................................................................77
Rear Panel...........................................................................................................78
Status Information................................................................................................79
Power On and Shut Down....................................................................................80
Power On.........................................................................................................80
Preferred Shutdown........................................................................................81
Forced Shutdown............................................................................................81
Boot Menu............................................................................................................81
Chapter 11 NETGEAR ReadyNAS 422
Front and Side Panels..........................................................................................84
Drive Bays............................................................................................................85
Rear Panel...........................................................................................................86
Status Information................................................................................................87
Power On and Shut Down....................................................................................87
Power On.........................................................................................................88
Preferred Shutdown........................................................................................88
Forced Shutdown............................................................................................88
Boot Menu............................................................................................................89
Chapter 12 NETGEAR ReadyNAS 424
Front and Side Panels..........................................................................................92
Drive Bays............................................................................................................93
Rear Panel...........................................................................................................94
Status Information................................................................................................95
Power On and Shut Down....................................................................................95
Power On.........................................................................................................96
Preferred Shutdown........................................................................................96
Forced Shutdown............................................................................................96
Boot Menu............................................................................................................97
Chapter 13 NETGEAR ReadyNAS 426
Front and Side Panels........................................................................................100
Drive Bays..........................................................................................................101
Rear Panel.........................................................................................................102
Status Information..............................................................................................103
Power On and Shut Down..................................................................................103
Power On.......................................................................................................104
Preferred Shutdown......................................................................................104
Forced Shutdown..........................................................................................105
Boot Menu..........................................................................................................105
5
ReadyNAS OS 6 Desktop Storage Systems
Chapter 14 NETGEAR ReadyNAS 428
Front and Side Panels........................................................................................108
Drive Bays..........................................................................................................109
Rear Panel.........................................................................................................110
Status Information..............................................................................................111
Power On and Shut Down..................................................................................111
Power On.......................................................................................................112
Preferred Shutdown......................................................................................112
Forced Shutdown..........................................................................................112
Boot Menu..........................................................................................................113
Chapter 15 NETGEAR ReadyNAS 516
Front and Side Panels........................................................................................116
Drive Bays..........................................................................................................116
Rear Panel.........................................................................................................117
Status Information..............................................................................................118
Power On and Shut Down..................................................................................119
Power On.......................................................................................................119
Preferred Shutdown......................................................................................120
Forced Shutdown..........................................................................................120
Boot Menu..........................................................................................................120
Chapter 16 NETGEAR ReadyNAS 524X
Front and Side Panels........................................................................................123
Drive Bays..........................................................................................................124
Rear Panel.........................................................................................................125
Status Information..............................................................................................126
Power On and Shut Down..................................................................................127
Power On.......................................................................................................127
Preferred Shutdown......................................................................................128
Forced Shutdown..........................................................................................128
Boot Menu..........................................................................................................128
Chapter 17 NETGEAR ReadyNAS 526X and 626X
Front and Side Panels........................................................................................131
Drive Bays..........................................................................................................132
Rear Panel ReadyNAS 526X.............................................................................133
Rear Panel ReadyNAS 626X.............................................................................134
Status Information..............................................................................................135
Power On and Shut Down..................................................................................136
Power On.......................................................................................................136
Preferred Shutdown......................................................................................137
Forced Shutdown..........................................................................................137
Boot Menu..........................................................................................................137
Chapter 18 NETGEAR ReadyNAS 528X and 628X
Front and Side Panels........................................................................................140
6
ReadyNAS OS 6 Desktop Storage Systems
Drive Bays..........................................................................................................141
Rear Panel ReadyNAS 528X.............................................................................142
Rear Panel ReadyNAS 628X.............................................................................143
Status Information..............................................................................................144
Power On and Shut Down..................................................................................145
Power On.......................................................................................................145
Preferred Shutdown......................................................................................146
Forced Shutdown..........................................................................................146
Boot Menu..........................................................................................................146
Chapter 19 NETGEAR ReadyNAS 716X
Front and Side Panels........................................................................................149
Drive Bays..........................................................................................................149
Rear Panel.........................................................................................................150
Status Information..............................................................................................151
Power On and Shut Down..................................................................................153
Power On.......................................................................................................153
Preferred Shutdown......................................................................................154
Forced Shutdown..........................................................................................154
Boot Menu..........................................................................................................154
Chapter 20 NETGEAR EDA 500
Front and Side Panels........................................................................................157
Drive Bays..........................................................................................................157
Rear Panel.........................................................................................................158
Status Information..............................................................................................159
Power On and Shut Down..................................................................................160
Power On.......................................................................................................160
Preferred Shutdown......................................................................................161
Forced Shutdown..........................................................................................161
Chapter 21 Disks
Disk Trays...........................................................................................................163
Standard Disk Traydisk trays standard..........................................................163
EDA 500 Disk Tray.........................................................................................164
Supported Disks................................................................................................164
Previously Formatted Disks...............................................................................165
Reformat Previously For matted Disks...........................................................165
Migrate a Volume...........................................................................................166
Add a Disk..........................................................................................................166
Add a 3.5-Inch Disk.......................................................................................166
Add a 2.5-Inch Disk.......................................................................................171
Replace a Disk...................................................................................................175
Replace a 3.5-Inch Disk................................................................................175
Replace a 2.5-Inch Disk................................................................................180
Appendix A Defaults and Technical Specifications
Factor y Default Settings.....................................................................................184
7
ReadyNAS OS 6 Desktop Storage Systems
ReadyNAS 102 Technical Specifications...........................................................184
General:.........................................................................................................184
Physical dimensions (h x w x d):...................................................................185
Physical weight:.............................................................................................185
Power consumption:......................................................................................185
Electrical:.......................................................................................................185
Environmental requirements:........................................................................185
Certifications:................................................................................................185
ReadyNAS 104 Technical Specifications...........................................................186
General:.........................................................................................................186
Physical dimensions (h x w x d):...................................................................186
Physical weight:.............................................................................................186
Power consumption:......................................................................................186
Electrical:.......................................................................................................186
Environmental requirements:........................................................................187
Certifications:................................................................................................187
ReadyNAS 202 Technical Specifications...........................................................187
General:.........................................................................................................187
Physical dimensions (h x w x d):...................................................................187
Physical weight:.............................................................................................187
Power consumption:......................................................................................188
Electrical:.......................................................................................................188
Environmental requirements:........................................................................188
Certifications:................................................................................................188
ReadyNAS 212 Technical Specifications...........................................................188
General:.........................................................................................................188
Physical dimensions (h x w x d):...................................................................189
Physical weight:.............................................................................................189
Power consumption:......................................................................................189
Electrical:.......................................................................................................189
Environmental requirements:........................................................................189
Certifications:................................................................................................189
ReadyNAS 204 Technical Specifications...........................................................189
General:.........................................................................................................189
Physical dimensions (h x w x d):...................................................................190
Physical weight:.............................................................................................190
Power consumption:......................................................................................190
Electrical:.......................................................................................................190
Environmental requirements:........................................................................190
Certifications:................................................................................................190
ReadyNAS 214 Technical Specifications...........................................................191
General:.........................................................................................................191
Physical dimensions (h x w x d):...................................................................191
Physical weight:.............................................................................................191
Power consumption:......................................................................................191
Electrical:.......................................................................................................191
Environmental requirements:........................................................................191
Certifications:................................................................................................192
ReadyNAS 312 Technical Specifications...........................................................192
8
ReadyNAS OS 6 Desktop Storage Systems
General:.........................................................................................................192
Physical dimensions (h x w x d):...................................................................192
Physical weight:.............................................................................................192
Power consumption:......................................................................................192
Electrical:.......................................................................................................193
Environmental requirements:........................................................................193
Certifications:................................................................................................193
ReadyNAS 314 Technical Specifications...........................................................193
General:.........................................................................................................193
Physical dimensions (h x w x d):...................................................................193
Physical weight:.............................................................................................194
Power consumption:......................................................................................194
Electrical:.......................................................................................................194
Environmental requirements:........................................................................194
Certifications:................................................................................................194
ReadyNAS 316 Technical Specifications...........................................................194
General:.........................................................................................................194
Physical dimensions (h x w x d):...................................................................195
Physical weight:.............................................................................................195
Power consumption:......................................................................................195
Electrical:.......................................................................................................195
Environmental requirements:........................................................................195
Certifications:................................................................................................196
ReadyNAS 422 Technical Specifications...........................................................196
General:.........................................................................................................196
Physical dimensions (h x w x d):...................................................................196
Physical weight:.............................................................................................196
Power consumption:......................................................................................196
Electrical:.......................................................................................................196
Environmental requirements:........................................................................197
Certifications:................................................................................................197
ReadyNAS 424 Technical Specifications...........................................................197
General:.........................................................................................................197
Physical dimensions (h x w x d):...................................................................197
Physical weight:.............................................................................................197
Power consumption:......................................................................................198
Electrical:.......................................................................................................198
Environmental requirements:........................................................................198
Certifications:................................................................................................198
ReadyNAS 426 Technical Specifications...........................................................198
General:.........................................................................................................198
Physical dimensions (h x w x d):...................................................................199
Physical weight:.............................................................................................199
Power consumption:......................................................................................199
Electrical:.......................................................................................................199
Environmental requirements:........................................................................199
Certifications:................................................................................................199
ReadyNAS 428 Technical Specifications...........................................................200
General:.........................................................................................................200
9
ReadyNAS OS 6 Desktop Storage Systems
Physical dimensions (h x w x d):...................................................................200
Physical weight:.............................................................................................200
Power consumption:......................................................................................200
Electrical:.......................................................................................................200
Environmental requirements:........................................................................201
Certifications:................................................................................................201
ReadyNAS 516 Technical Specifications...........................................................201
General:.........................................................................................................201
Physical dimensions (h x w x d):...................................................................201
Physical weight:.............................................................................................201
Power consumption:......................................................................................202
Electrical:.......................................................................................................202
Environmental requirements:........................................................................202
Certifications:................................................................................................202
ReadyNAS 524X Technical Specifications.........................................................202
General:.........................................................................................................202
Physical dimensions (h x w x d):...................................................................203
Physical weight:.............................................................................................203
Power consumption:......................................................................................203
Electrical:.......................................................................................................203
Environmental requirements:........................................................................203
Certifications:................................................................................................203
ReadyNAS 526X Technical Specifications.........................................................204
General:.........................................................................................................204
Physical dimensions (h x w x d):...................................................................204
Physical weight:.............................................................................................204
Power consumption:......................................................................................204
Electrical:.......................................................................................................204
Environmental requirements:........................................................................205
Certifications:................................................................................................205
ReadyNAS 528X Technical Specifications.........................................................205
General:.........................................................................................................205
Physical dimensions (h x w x d):...................................................................205
Physical weight:.............................................................................................205
Power consumption:......................................................................................206
Electrical:.......................................................................................................206
Environmental requirements:........................................................................206
Certifications:................................................................................................206
ReadyNAS 626X Technical Specifications.........................................................206
General:.........................................................................................................206
Physical dimensions (h x w x d):...................................................................207
Physical weight:.............................................................................................207
Power consumption:......................................................................................207
Electrical:.......................................................................................................207
Environmental requirements:........................................................................207
Certifications:................................................................................................207
ReadyNAS 628X Technical Specifications.........................................................208
General:.........................................................................................................208
Physical dimensions (h x w x d):...................................................................208
10
ReadyNAS OS 6 Desktop Storage Systems
Physical weight:.............................................................................................208
Power consumption:......................................................................................208
Electrical:.......................................................................................................208
Environmental requirements:........................................................................209
Certifications:................................................................................................209
ReadyNAS 716X Technical Specifications.........................................................209
General:.........................................................................................................209
Physical dimensions (h x w x d):...................................................................209
Physical weight:.............................................................................................209
Power consumption:......................................................................................210
Electrical:.......................................................................................................210
Environmental requirements:........................................................................210
Certifications:................................................................................................210
EDA 500 Technical Specifications......................................................................210
General:.........................................................................................................210
Physical dimensions (h x w x d):...................................................................210
Physical weight:.............................................................................................211
Power consumption:......................................................................................211
Electrical:.......................................................................................................211
Environmental requirements:........................................................................211
Certifications:................................................................................................211
Safety Warnings.................................................................................................211
Electrical Safety Precautions.........................................................................212
General Safety Precautions..........................................................................212
Electrostatic Discharge Precautions..............................................................212
11
ReadyNAS OS 6 Desktop Storage Systems
1
Getting Started
Congratulations on your purchase of a NETGEAR ReadyNAS® storage system.This manual describes the
physical features of the ReadyNAS OS 6 desktop storage systems.
This chapter contains the following sections:
•Additional Documentation on page 13
•Setup Location on page 13
•Supported Operating Systems on page 13
•Supported Browsers on page 14
•Diskless Storage Systems on page 14
12
Additional Documentation
For detailed information about configuring, managing, and using your ReadyNAS storage system, see the
ReadyNAS OS 6 Software Manual, which is available at netgear.com/support/product/ReadyNAS_OS_6.
NETGEAR maintains a community website that supports ReadyNAS products.Visit
www.netgear.com/readynas for reviews, tutorials, a comparison chart, software updates, documentation,
an active user forum, and much more.
Setup Location
Your ReadyNAS storage system is suitable for use in a home or small office environment where it can be
freestanding.The small, compact size makes it suitable for sitting on a desk or on a closet shelf.
Choose a location for your storage system that meets these criteria:
•Cables can be connected easily.
•Water or moisture cannot enter the case.
•Airflow around the storage system and through the vents in the side of the case is not restricted.
•The air is as free of dust as possible.
•Temperature operating limits are not likely to be exceeded.
•If you are using an uninterruptab le po wer supply (UPS) for protection, the power cab le can be securely
and safely connected to the UPS.
Supported Operating Systems
The ReadyNAS storage system is supported on the following systems:
•Microsoft Windows 10 (32 bit and 64 bit)
•Microsoft Windows 8.1 (32 bit and 64 bit)
•Microsoft Windows 8 (32 bit and 64 bit)
•Microsoft Windows 7 (32 bit and 64 bit)
•Windows Server 2016 (64 bit)
•Windows Server 2012 R2 (64 bit)
•Microsoft Server 2012 (64 bit)
•Microsoft Server 2008 R2 (64 bit)
•Apple OS X 10.7 or later
•Linux, UNIX, Solaris
•Apple iOS
•Google Android
Getting Started
13
ReadyNAS OS 6 Desktop Storage Systems
Supported Browsers
The ReadyNAS local admin page supports the following browsers:
•Microsoft Edge
•Microsoft Internet Explorer 9.0 and later
•Apple Safari, 5.0 and later
•Google Chrome 20 and later
•Mozilla Firefox 14 and later
If you experience difficulty accessing the local admin page or if you notice unexpected behavior, try using
another browser. For more information about the ReadyNAS local admin page, see the ReadyNAS OS 6
Software Manual, which is available at netgear.com/support/product/ReadyNAS_OS_6.
Diskless Storage Systems
If you purchased a ReadyNAS storage system without a preinstalled disk drive or drives, you must add at
least one disk your system before you use the system.You can add a 3.5-inch hard disk drive, a 2.5-inch
hard disk drive, or a 2.5-inch solid state drive to an empty drive bay. For information about how to install a
disk, see Add a Disk on page 166.
Use only supported SATA hard disk drives (HDD) or solid state drives (SSD) in your ReadyNAS storage
system. If you use disks that are not supported, NETGEAR technical support will not provide assistance.
For a list of supported disks, see the NETGEAR Hardware Compatibility List at netgear.com/readynas-hcl.
If you are adding a previously formatted disk to your storage system, see the instructions in Previously
Formatted Disks on page 165.
Getting Started
14
ReadyNAS OS 6 Desktop Storage Systems
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 102.
Figure 1. ReadyNAS 102 front and side panels
1. Power button and LED
2. Disk activity LED
3. Exhaust vent
4. USB 2.0 port
5. Backup button
6. USB and Backup status LED
7. Disk 1 and Disk 2 LEDs
8. Drive bay door
Drive Bays
The following figure shows the drive bays of the ReadyNAS 102.
NETGEAR ReadyNAS 102
16
ReadyNAS OS 6 Desktop Storage Systems
Figure 2. ReadyNAS 102 drive bays
1. Drive bay door
2. Disk tray handle
3. Recessed disk tray handle lock
4. Disk tray release latch
5. Drive bays
Rear Panel
The following figure shows the rear panel of the ReadyNAS 102.
NETGEAR ReadyNAS 102
17
ReadyNAS OS 6 Desktop Storage Systems
Figure 3. ReadyNAS 102 rear panel
1. Exhaust fan
2. Kensington lock
3. GbE ports with LED status indicators
4. USB 3.0 ports
5. eSATA port
6. Reset button
7. Power adapter socket
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
NETGEAR ReadyNAS 102
18
ReadyNAS OS 6 Desktop Storage Systems
Table 1. ReadyNAS 102 indicator descriptions
DescriptionIndicator
Press this button to turn on the ReadyNAS.The LED indicates these states:
•On. Powered on.
•Blinking. Booting or shutting down.
•Off. Powered off.
Power button and LED
An LED on the front panel of the storage system is associated with each drive bay.
The disk LEDs have these states:
•On. Power is on and the disk is operating normally.
•Blinking.The disk was removed, failed, or is resynchronizing.
•Off.The drive bay is empty.
Disk LEDs (1, 2)
The disk activity LED has these states:
•On. At least one disk is present.
•Blinking. A disk is active.
•Off. All disks are idle.
Disk activity LED
Two LED status indicators are built into this port, one green and one amber.They
indicate port speed and activity as follows:
•Green on, amber off. 1000 Mbps connection speed, no activity.
•Green blinking, amber off. 1000 Mbps connection speed, activity.
•Green off, amber on. 10 Mbps or 100 Mbps connection speed, no activity.
•Green off, amber blinking. 10 Mbps or 100 Mbps connection speed, activity.
•Green off, amber off. No connection.
Rear panel Ethernet port
LEDs
Power On and Shut Down
This section describes how to pow er on and shut down y our system. If you m ust shut down the system, use
one of the preferred shutdown methods whenever possible.
NETGEAR ReadyNAS 102
19
ReadyNAS OS 6 Desktop Storage Systems
Power On
When you connect the system to a power supply or the system recovers from a power outage, the system
returns to its last state:
•If the system was powered on, the system automatically powers on again when the power supply is
connected or power is restored.
•If the system was powered off, the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. Press the Power button.
The Power LED blinks, prompting you to confirm the shutdown.
2. Press the Power button again.
The system shuts down gracefully.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
•Unplug the system from the power supply.
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 5 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
NETGEAR ReadyNAS 102
20
ReadyNAS OS 6 Desktop Storage Systems
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the f actory default process immediately, press the Backup button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your storage system, such as Internet protocol settings and the administrator password,
to defaults.
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when a
NETGEAR technical support representative instructs you to do so.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The pass or fail result is reported using the storage system's
LEDs. Contact a NETGEAR technical support representative to interpret memory test results.
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button.
The system powers on.
4. Continue to press the Reset button until the Power button LED, USB and backup status LED, disk 1
LED, and disk 2 LED light.
5. Press the Backup button to scroll through boot mode options.
The storage system shows the boot mode options using the LEDs, as described in the following table:
Status IndicatorBoot Mode
USB and
Backup
LED
Disk 2
LED
Disk 1
LED
Power
LED
Description
All four LEDs light.Boot menu
Power LED lights.Normal
Disk 1 LED lights.Factory default
NETGEAR ReadyNAS 102
21
ReadyNAS OS 6 Desktop Storage Systems
(Continued)
Status IndicatorBoot Mode
USB and
Backup
LED
Disk 2
LED
Disk 1
LED
Power
LED
Description
Disk 2 LED lights.OS reinstall
USB and backup status LED lights.Tech support
Power LED and disk 1 LED light.Volume read only
Power LED and disk 2 LED light.Memory test
P ower LED and USB and bac kup status LED
light.
Test disk
Legend:
•On:
•Off:
6. Press and release the Reset button to confirm your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 102
22
ReadyNAS OS 6 Desktop Storage Systems
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 104.
Figure 4. ReadyNAS 104 front and side panels
1. Exhaust vents
2. USB 2.0 port
3. Backup button and LED
4. Disk LEDs
5. Disk activity LED
6. Power button and LED
7. Drive bay door
8. Status display screen
Drive Bays
The following figure shows the drive bays of the ReadyNAS 104.
NETGEAR ReadyNAS 104
24
ReadyNAS OS 6 Desktop Storage Systems
Figure 5. ReadyNAS 104 drive bays
1. Drive bay door
2. Disk tray handle
3. Recessed disk tray handle lock
4. Disk tray release latch
5. Drive bays
Rear Panel
The following figure shows the rear panel of the ReadyNAS 104.
NETGEAR ReadyNAS 104
25
ReadyNAS OS 6 Desktop Storage Systems
Figure 6. ReadyNAS 104 rear panel
1. eSATA port
2. Reset button
3. USB 3.0 ports
4. GbE ports with LED status indicators
The two GbE ports are equivalent.They can be used as two separate Ethernet
connections, or can be configured as a single, bonded port with a 2 Gbps potential
speed. For information about how to configure a bonded port, and the network
configuration requirements needed to support 2 Gbps, see the ReadyNAS OS 6
Software Manual, which is available at netgear.com/support/product/ReadyNAS_OS_6.
Note
5. Power cable socket
6. Exhaust fan
7. Kensington lock
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
NETGEAR ReadyNAS 104
26
ReadyNAS OS 6 Desktop Storage Systems
Table 2. ReadyNAS 104 indicator descriptions
DescriptionIndicator
Press this button to turn on the ReadyNAS.The LED indicates these states:
•On. Powered on.
•Blinking. Booting or shutting down.
•Off. Powered off.
Power button and LED
An LED on the top of the front panel is associated with each drive bay. LEDs are in
numerical order from left to right.The disk LEDs indicate these states:
•On. Power is on and the disk is operating normally.
•Blinking.The disk was removed, failed, or is resynchronizing. See the display
screen for details.
•Off.The drive bay is empty.
Disk LEDs (1, 2, 3, 4)
The disk activity LED indicates these states:
•On. At least one disk is present.
•Blinking. A disk is active.
•Off. All disks are idle.
Disk activity LED
Two LED status indicators are built into this port, one green and one amber.They
indicate port speed and activity as follows:
•Green on, amber off. 1000 Mbps connection speed, no activity.
•Green blinking, amber off. 1000 Mbps connection speed, activity.
•Green off, amber on. 10 Mbps or 100 Mbps connection speed, no activity.
•Green off, amber blinking. 10 Mbps or 100 Mbps connection speed, activity.
•Green off, amber off. No connection.
Rear panel Ethernet port
LEDs
Displays messages about the status of your storage system. Note that the status
display screen goes to sleep to prevent burn-in.To wake it, press the Power button
once. If the storage system reports an abnormal operation or error , the status display
screen stays on.
Status display screen
Power On and Shut Down
This section describes how to power on and shut down your system. If you need to shut down the system,
use one of the preferred shutdown methods whenever possible.
NETGEAR ReadyNAS 104
27
ReadyNAS OS 6 Desktop Storage Systems
Power On
When you connect the system to a power supply or the system recovers from a power outage, the system
returns to its last state:
•If the system was powered on, the system automatically powers on again when the power supply is
connected or power is restored.
•If the system was powered off, the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. If the status display screen is not lit, do the following:
a. Press the Power button.
The status display screen wakes.
b. Press the Power button a second time.
Instructions for graceful shutdown display on the status display screen.
c. Press the Power button a third time.
The system shuts down gracefully.
2. If the status display screen is lit, do the following:
a. Press the Power button.
Instructions for graceful shutdown display on the status display screen.
b. Press the Power button again.
The system shuts down gracefully.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
•Unplug the system from the power supply.
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
NETGEAR ReadyNAS 104
28
ReadyNAS OS 6 Desktop Storage Systems
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 5 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the f actory default process immediately, press the Backup button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your storage system, such as Internet protocol settings and the administrator password,
to defaults.
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when a
NETGEAR technical support representative instructs you to do so.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The pass or fail result is reported on the status display screen.
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button.
The system powers on.
4. Continue to press the Reset button until the status display screen shows a boot menu message.
5. Press the Backup button to scroll through boot mode options.
The status display screen shows the current boot mode option.
6. When the status display screen shows the boot mode that you need, press and release the Reset button
to confirm your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 104
29
ReadyNAS OS 6 Desktop Storage Systems
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 202.
Figure 7. ReadyNAS 202 front and side panels
1. Power button and LED
2. Disk activity LED
3. Exhaust vent
4. USB 3.0 port
5. Backup button
6. USB and backup status LED
7. Disk 1 and Disk 2 LEDs
8. Drive bay door
Drive Bays
The following figure shows the drive bays of the ReadyNAS 202.
NETGEAR ReadyNAS 202
31
ReadyNAS OS 6 Desktop Storage Systems
Figure 8. ReadyNAS 202 drive bays
1. Drive bay door
2. Disk tray handle
3. Recessed disk tray handle lock
4. Disk tray release latch
5. Drive bays
Rear Panel
The following figure shows the rear panel of the ReadyNAS 202.
NETGEAR ReadyNAS 202
32
ReadyNAS OS 6 Desktop Storage Systems
Figure 9. ReadyNAS 202 rear panel
1. Exhaust fan
2. Kensington lock
3. USB 3.0 ports
4. eSATA port
5. GbE ports with LED status indicators
The two GbE ports are equivalent.They can be used as two separate Ethernet
connections, or can be configured as a single, bonded port with a 2 Gbps potential
speed. For information on how to configure a bonded port, and the network
configuration requirements needed to support 2 Gbps, see the ReadyNAS OS 6
Software Manual, which is available at netgear.com/support/product/ReadyNAS_OS_6.
Note
6. Reset button
7. Power adapter socket
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
NETGEAR ReadyNAS 202
33
ReadyNAS OS 6 Desktop Storage Systems
Table 3. ReadyNAS 202 indicator descriptions
DescriptionIndicator
Press this button to turn on the ReadyNAS.The LED has these states:
•On. Powered on.
•Blinking. Booting or shutting down.
•Off. Powered off.
Power button and LED
Each drive bay has an LED associated with it on the front panel of the storage
system.The disk LEDs have these states:
•On. Power is on and the disk is operating normally.
•Blinking.The disk was removed, failed, or is resynchronizing. See the display
screen for details.
•Off.The drive bay is empty.
Disk LEDs (1, 2)
The disk activity LED has these states:
•Blinking. A disk is active.
•Off. Disk is idling.
Disk activity LED
Two LED status indicators are b uilt into each port, one off or green and one showing
three states: off, amber, or green.They indicate port speed and activity as follows:
•Green, green. 1000 Mbps connection speed, no activity.
•Green blinking, green. 1000 Mbps connection speed, activity.
•Green, amber. 100 Mbps connection speed, no activity.
•Green blinking, amber. 100 Mbps connection speed, activity.
•Green on, off. 10 Mbps connection speed, no activity.
•Green blinking, off. 10 Mbps connection speed, activity.
•Off, off. No connection.
Rear panel Ethernet port
LEDs
Power On and Shut Down
This section describes how to pow er on and shut down y our system. If you m ust shut down the system, use
one of the preferred shutdown methods whenever possible.
NETGEAR ReadyNAS 202
34
ReadyNAS OS 6 Desktop Storage Systems
Power On
When you connect the system to a power supply or the system recovers from a power outage, the system
returns to its last state:
•If the system was powered on, the system automatically powers on again when the power supply is
connected or power is restored.
•If the system was powered off, the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. Press the Power button.
The Power LED blinks, prompting you to confirm the shutdown.
2. Press the Power button again.
The system shuts down gracefully.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
•Unplug the system from the power supply.
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 5 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
NETGEAR ReadyNAS 202
35
ReadyNAS OS 6 Desktop Storage Systems
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the f actory default process immediately, press the Backup button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your storage system, such as Internet protocol settings and the administrator password,
to defaults.
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when a
NETGEAR technical support representative instructs you to do so.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The memory test runs for eight hours.The current status and
the pass or fail result is reported using the storage system LEDs, as described in the following table:
Figure 10. Memory Test Status
Backup LEDDisk 2 LEDDisk 1 LEDPower LEDMemory Test State
BlinkingOffOffOff1st hour
OffBlinkingOffOff2nd hour
OffOffBlinkingOff3rd hour
BlinkingBlinkingBlinkingOff4th hour
BlinkingOffOffOn5th hour
OffBlinkingOffOn6th hour
OffOffBlinkingOn7th hour
BlinkingBlinkingBlinkingOn8th hour
BlinkingBlinkingBlinkingBlinkingResult: fail
OnOnOnOnResult: pass
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
NETGEAR ReadyNAS 202
36
ReadyNAS OS 6 Desktop Storage Systems
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button.
The system powers on.
4. Continue to press the Reset b utton until the Pow er LED, USB and backup status LED, disk 1 LED, and
disk 2 LED light.
5. Press the Backup button to scroll through boot mode options.
The storage system shows the boot mode options using the LEDs, as described in the following table:
Status IndicatorBoot Mode
USB and
Backup
LED
Disk 2
LED
Disk 1
LED
Power
LED
Description
All four LEDs light.Boot menu
Power LED lights.Normal
Disk 1 LED lights.Factory default
Disk 2 LED lights.OS reinstall
USB and backup status LED lights.Tech support
Power LED and disk 1 LED light.Volume read only
Power LED and disk 2 LED light.Memory test
P ower LED and USB and bac kup status LED
light.
Test disk
Legend:
•On:
•Off:
6. Press and release the Reset button to confirm your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 202
37
ReadyNAS OS 6 Desktop Storage Systems
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 204.
Figure 11. ReadyNAS 204 front and side panels
1. Exhaust vents
2. USB 2.0 port
3. Backup button and LED
4. Disk LEDs
5. Disk activity LED
6. Power button and LED
7. Drive bay door
8. Status display screen
Drive Bays
The following figure shows the drive bays of the ReadyNAS 204.
NETGEAR ReadyNAS 204
39
ReadyNAS OS 6 Desktop Storage Systems
Figure 12. ReadyNAS 204 drive bays
1. Drive bay door
2. Disk tray handle
3. Recessed disk tray handle lock
4. Disk tray release latch
5. Drive bays
Rear Panel
The following figure shows the rear panel of the ReadyNAS 204.
NETGEAR ReadyNAS 204
40
ReadyNAS OS 6 Desktop Storage Systems
Figure 13. ReadyNAS 204 rear panel
1. eSATA port
2. Reset button
3. USB 3.0 ports
4. LAN ports with LED status indicators
The two LAN ports are equivalent.They can be used as two separate Ethernet
connections, or can be configured as a single, bonded port with a 2 Gbps potential
speed. For information about how to configure a bonded port, and the network
configuration requirements needed to support 2 Gbps, see the ReadyNAS OS 6
Software Manual, which is available at netgear.com/support/product/ReadyNAS_OS_6.
Note
5. Power cable socket
6. Exhaust fan
7. Kensington lock
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
NETGEAR ReadyNAS 204
41
ReadyNAS OS 6 Desktop Storage Systems
Table 4. ReadyNAS 204 indicator descriptions
DescriptionIndicator
Press this button to turn on the ReadyNAS.The LED indicates these states:
•On. Powered on.
•Blinking. Booting or shutting down.
•Off. Powered off.
Power button and LED
An LED on the top of the front panel is associated with each drive bay. LEDs are in
numerical order from left to right.The disk LEDs indicate these states:
•On. Power is on and the disk is operating normally.
•Blinking.The disk was removed, failed, or is resynchronizing. See the display
screen for details.
•Off.The drive bay is empty.
Disk LEDs (1, 2, 3, 4)
The disk activity LED indicates these states:
•Blinking. A disk is being accessed.
•Off. All disks are idle.
Disk activity LED
Two LED status indicators are b uilt into each port, one off or green and one showing
three states: off, amber, or green.They indicate port speed and activity as follows:
•Green, green. 1000 Mbps connection speed, no activity.
•Green blinking, green. 1000 Mbps connection speed, activity.
•Green, amber. 100 Mbps connection speed, no activity.
•Green blinking, amber. 100 Mbps connection speed, activity.
•Green on, off. 10 Mbps connection speed, no activity.
•Green blinking, off. 10 Mbps connection speed, activity.
•Off, off. No connection.
Rear panel Ethernet port
LEDs
Displays messages about the status of your storage system. Note that the status
display screen goes to sleep to prevent burn-in.To wake it, press the Power button
once. If the storage system reports an abnormal operation or error , the status display
screen stays on.
Status display screen
Power On and Shut Down
This section describes how to pow er on and shut down y our system. If you m ust shut down the system, use
one of the preferred shutdown methods whenever possible.
NETGEAR ReadyNAS 204
42
ReadyNAS OS 6 Desktop Storage Systems
Power On
When you connect the system to a power supply or the system recovers from a power outage, the system
returns to its last state:
•If the system was powered on, the system automatically powers on again when the power supply is
connected or power is restored.
•If the system was powered off, the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. If the status display screen is not lit, do the following:
a. Press the Power button.
The status display screen wakes.
b. Press the Power button a second time.
Instructions for graceful shutdown display on the status display screen.
c. Press the Power button a third time.
The system shuts down gracefully.
2. If the status display screen is lit, do the following:
a. Press the Power button.
Instructions for graceful shutdown display on the status display screen.
b. Press the Power button again.
The system shuts down gracefully.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
•Unplug the system from the power supply.
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
NETGEAR ReadyNAS 204
43
ReadyNAS OS 6 Desktop Storage Systems
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 5 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the f actory default process immediately, press the Backup button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your storage system, such as Internet protocol settings and the administrator password,
to defaults.
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when a
NETGEAR technical support representative instructs you to do so.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The pass or fail result is reported on the status display screen.
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button.
The system powers on.
4. Continue to press the Reset button until the status display screen shows a boot menu message.
5. Press the Backup button to scroll through boot mode options.
The status display screen shows the current boot mode option.
6. When the status display screen shows the boot mode that you need, press and release the Reset button
to confirm your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 204
44
ReadyNAS OS 6 Desktop Storage Systems
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 212.
Figure 14. ReadyNAS 212 front and side panels
1. Power button and LED
2. Disk activity LED
3. Exhaust vent
4. USB 3.0 port
5. Backup button
6. USB and backup status LED
7. Disk 1 and Disk 2 LEDs
8. Drive bay door
Drive Bays
The following figure shows the drive bays of the ReadyNAS 212.
NETGEAR ReadyNAS 212
46
ReadyNAS OS 6 Desktop Storage Systems
Figure 15. ReadyNAS 212 drive bays
1. Drive bay door
2. Disk tray handle
3. Recessed disk tray handle lock
4. Disk tray release latch
5. Drive bays
Rear Panel
The following figure shows the rear panel of the ReadyNAS 212.
NETGEAR ReadyNAS 212
47
ReadyNAS OS 6 Desktop Storage Systems
Figure 16. ReadyNAS 212 rear panel
1. Exhaust fan
2. Kensington lock
3. USB 3.0 ports
4. eSATA port
5. GbE ports with LED status indicators
The two GbE ports are equivalent.They can be used as two separate Ethernet
connections, or can be configured as a single, bonded port with a 2 Gbps potential
speed. For information about how to configure a bonded port, and the network
configuration requirements needed to support 2 Gbps, see the ReadyNAS OS 6
Software Manual, which is available at netgear.com/support/product/ReadyNAS_OS_6.
Note
6. Reset button
7. Power adapter socket
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
NETGEAR ReadyNAS 212
48
ReadyNAS OS 6 Desktop Storage Systems
Table 5. ReadyNAS 212 indicator descriptions
DescriptionIndicator
Press this button to turn on the ReadyNAS.The LED indicates these states:
•On. Powered on.
•Blinking. Booting or shutting down.
•Off. Powered off.
Power button and LED
An LED on the front panel of the storage system is associated with each drive bay
The disk LEDs indicate these states:
•On. Power is on and the disk is operating normally.
•Blinking.The disk was removed, failed, or is resynchronizing. See the display
screen for details.
•Off.The drive bay is empty.
Disk LEDs (1, 2)
The disk activity LED indicates these states:
•Blinking. A disk is active.
•Off. disk is idling.
Disk activity LED
Two LED status indicators are b uilt into each port, one off or green and one showing
three states: off, amber, or green.They indicate port speed and activity as follows:
•Green, green. 1000 Mbps connection speed, no activity.
•Green blinking, green. 1000 Mbps connection speed, activity.
•Green, amber. 100 Mbps connection speed, no activity.
•Green blinking, amber. 100 Mbps connection speed, activity.
•Green on, off. 10 Mbps connection speed, no activity.
•Green blinking, off. 10 Mbps connection speed, activity.
•Off, off. No connection.
Rear panel Ethernet port
LEDs
Power On and Shut Down
This section describes how to pow er on and shut down y our system. If you m ust shut down the system, use
one of the preferred shutdown methods whenever possible.
NETGEAR ReadyNAS 212
49
ReadyNAS OS 6 Desktop Storage Systems
Power On
When you connect the system to a power supply or the system recovers from a power outage, the system
returns to its last state:
•If the system was powered on, the system automatically powers on again when the power supply is
connected or power is restored.
•If the system was powered off, the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. Press the Power button.
The Power LED blinks, prompting you to confirm the shutdown.
2. Press the Power button again.
The system shuts down gracefully.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
•Unplug the system from the power supply.
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 5 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
NETGEAR ReadyNAS 212
50
ReadyNAS OS 6 Desktop Storage Systems
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the f actory default process immediately, press the Backup button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your storage system, such as Internet protocol settings and the administrator password,
to defaults.
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when a
NETGEAR technical support representative instructs you to do so.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The memory test runs for eight hours.The current status and
the pass or fail result is reported using the storage system LEDs, as described in the following table:
Figure 17. Memory Test Status
Backup LEDDisk 2 LEDDisk 1 LEDPower LEDMemory Test State
BlinkingOffOffOffFirst hour
OffBlinkingOffOffSecond hour
OffOffBlinkingOffThird hour
BlinkingBlinkingBlinkingOffForth hour
BlinkingOffOffOnFifth hour
OffBlinkingOffOnSixth hour
OffOffBlinkingOnSeventh hour
BlinkingBlinkingBlinkingOnEigth hour
BlinkingBlinkingBlinkingBlinkingResult: fail
OnOnOnOnResult: pass
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
NETGEAR ReadyNAS 212
51
ReadyNAS OS 6 Desktop Storage Systems
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button.
The system powers on.
4. Continue to press the Reset button until the Power button LED, USB and backup status LED, disk 1
LED, and disk 2 LED light.
5. Press the Backup button to scroll through boot mode options.
The storage system shows the boot mode options using the LEDs, as described in the following table:
Status IndicatorBoot Mode
USB and
Backup
LED
Disk 2
LED
Disk 1
LED
Power
LED
Description
All four LEDs light.Boot menu
Power LED lights.Normal
Disk 1 LED lights.Factory default
Disk 2 LED lights.OS reinstall
USB and backup status LED lights.Tech support
Power LED and disk 1 LED light.Volume read only
Power LED and disk 2 LED light.Memory test
P ower LED and USB and bac kup status LED
light.
Test disk
Legend:
•On:
•Off:
6. Press and release the Reset button to confirm your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 212
52
ReadyNAS OS 6 Desktop Storage Systems
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 214.
Figure 18. ReadyNAS 214 front and side panels
1. Exhaust vents
2. USB 2.0 port
3. Backup button and LED
4. Disk LEDs
5. Disk activity LED
6. Power button and LED
7. Drive bay door
8. Status display screen
Drive Bays
The following figure shows the drive bays of the ReadyNAS 214.
NETGEAR ReadyNAS 214
54
ReadyNAS OS 6 Desktop Storage Systems
Figure 19. ReadyNAS 214 drive bays
1. Drive bay door
2. Disk tray handle
3. Recessed disk tray handle lock
4. Disk tray release latch
5. Drive bays
Rear Panel
The following figure shows the rear panel of the ReadyNAS 214.
NETGEAR ReadyNAS 214
55
ReadyNAS OS 6 Desktop Storage Systems
Figure 20. ReadyNAS 214 rear panel
1. eSATA port
2. Reset button
3. USB 3.0 ports
4. LAN ports with LED status indicators
The two LAN ports are equivalent.They can be used as two separate Ethernet
connections, or can be configured as a single, bonded port with a 2 Gbps potential
speed. For information about how to configure a bonded port, and the network
configuration requirements needed to support 2 Gbps, see the ReadyNAS OS 6
Software Manual, which is available at netgear.com/support/product/ReadyNAS_OS_6.
Note
5. Power cable socket
6. Exhaust fan
7. Kensington lock
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
NETGEAR ReadyNAS 214
56
ReadyNAS OS 6 Desktop Storage Systems
Table 6. ReadyNAS 214 indicator descriptions
DescriptionIndicator
Press this button to turn on the ReadyNAS.The LED indicates these states:
•On. Powered on.
•Blinking. Booting or shutting down.
•Off. Powered off.
Power button and LED
An LED on the top of the front panel is associated with each drive bay. LEDs are in
numerical order from left to right.The disk LEDs indicate these states:
•On. Power is on and the disk is operating normally.
•Blinking.The disk was removed, failed, or is resynchronizing. See the display
screen for details.
•Off.The drive bay is empty.
Disk LEDs (1, 2, 3, 4)
The disk activity LED indicate these states:
•Blinking. A disk is being accessed.
•Off. All disks are idle.
Disk activity LED
Two LED status indicators are b uilt into each port, one off or green and one showing
three states: off, amber, or green.They indicate port speed and activity as follows:
•Green, green. 1000 Mbps connection speed, no activity.
•Green blinking, green. 1000 Mbps connection speed, activity.
•Green, amber. 100 Mbps connection speed, no activity.
•Green blinking, amber. 100 Mbps connection speed, activity.
•Green on, off. 10 Mbps connection speed, no activity.
•Green blinking, off. 10 Mbps connection speed, activity.
•Off, off. No connection.
Rear panel Ethernet port
LEDs
Displays messages about the status of your storage system. Note that the status
display screen goes to sleep to prevent burn-in.To wake it, press the Power button
once. If the storage system reports an abnormal operation or error , the status display
screen stays on.
Status display screen
Power On and Shut Down
This section describes how to pow er on and shut down y our system. If you m ust shut down the system, use
one of the preferred shutdown methods whenever possible.
NETGEAR ReadyNAS 214
57
ReadyNAS OS 6 Desktop Storage Systems
Power On
When you connect the system to a power supply or the system recovers from a power outage, the system
returns to its last state:
•If the system was powered on, the system automatically powers on again when the power supply is
connected or power is restored.
•If the system was powered off, the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. If the status display screen is not lit, do the following:
a. Press the Power button.
The status display screen wakes.
b. Press the Power button a second time.
Instructions for graceful shutdown display on the status display screen.
c. Press the Power button a third time.
The system shuts down gracefully.
2. If the status display screen is lit, do the following:
a. Press the Power button.
Instructions for graceful shutdown display on the status display screen.
b. Press the Power button again.
The system shuts down gracefully.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
•Unplug the system from the power supply.
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
NETGEAR ReadyNAS 214
58
ReadyNAS OS 6 Desktop Storage Systems
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 5 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the f actory default process immediately, press the Backup button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your storage system, such as Internet protocol settings and the administrator password,
to defaults.
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when a
NETGEAR technical support representative instructs you to do so.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The pass or fail result is reported on the status display screen.
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button.
The system powers on.
4. Continue to press the Reset button until the status display screen shows a boot menu message.
5. Press the Backup button to scroll through boot mode options.
The status display screen shows the current boot mode option.
6. When the status display screen shows the boot mode that you need, press and release the Reset button
to confirm your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 214
59
ReadyNAS OS 6 Desktop Storage Systems
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 312.
Figure 21. ReadyNAS 312 front and side panels
1. Power button and LED
2. Disk activity LED
3. Exhaust vent
4. USB 2.0 port
5. Infrared remote receiver
6. Backup button
7. USB and Backup status LED
8. Disk 1 and Disk 2 LEDs
9. Drive bay door
Drive Bays
The following figure shows the drive bays of the ReadyNAS 312.
NETGEAR ReadyNAS 312
61
ReadyNAS OS 6 Desktop Storage Systems
Figure 22. ReadyNAS 312 drive bays
1. Drive bay door
2. Disk tray handle
3. Recessed disk tray handle lock
4. Disk tray release latch
5. Drive bays
Rear Panel
The following figure shows the rear panel of the ReadyNAS 312.
NETGEAR ReadyNAS 312
62
ReadyNAS OS 6 Desktop Storage Systems
Figure 23. ReadyNAS 312 rear panel
1. Exhaust fan
2. Kensington lock
3. USB 3.0 ports
4. eSATA port
5. LAN ports with LED status indicators
6. Reset button
7. HDMI port (currently not supported)
8. Power adapter socket
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
NETGEAR ReadyNAS 312
63
ReadyNAS OS 6 Desktop Storage Systems
Table 7. ReadyNAS 312 indicator descriptions
DescriptionIndicator
Press this button to turn on the ReadyNAS.The LED has these states:
•On. Powered on.
•Blinking. Booting or shutting down.
•Off. Powered off.
Power button and LED
An LED on the front panel of the storage system is associated with each drive bay
The disk LEDs have these states:
•On. Power is on and the disk is operating normally.
•Blinking.The disk was removed, failed, or is resynchronizing.
•Off.The drive bay is empty.
Disk LEDs (1, 2)
The disk activity LED has these states:
•On. At least one disk is present.
•Blinking. A disk is active.
•Off. All disks are idle.
Disk activity LED
Two LED status indicators are built into this port, one green and one amber.They
indicate port speed and activity as follows:
•Green on, amber off. 1000 Mbps connection speed, no activity.
•Green blinking, amber off. 1000 Mbps connection speed, activity.
•Green off, amber on. 10 Mbps or 100 Mbps connection speed, no activity.
•Green off, amber blinking. 10 Mbps or 100 Mbps connection speed, activity.
•Green off, amber off. No connection.
Rear panel Ethernet port
LEDs
Power On and Shut Down
This section describes how to power on and shut down your system. If you need to shut down the system,
use one of the preferred shutdown methods whenever possible.
Power On
When you connect the system to a po wer supply or the system reco v ers from a pow er outage, the f ollo wing
occurs:
NETGEAR ReadyNAS 312
64
ReadyNAS OS 6 Desktop Storage Systems
•The system automatically powers on if you enabled the Wake on LAN (WoL) feature or scheduled the
system to automatically power on or off.
•The system returns to its last state if the W ake on LAN (W oL) feature is disab led and you did not schedule
the system to automatically power on or off:
-If the system was powered on, the system automatically powers on again when the power supply
is connected or power is restored.
-If the system was powered off , the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. Press the Power button.
The Power LED blinks, prompting you to confirm the shutdown.
2. Press the Power button again.
The system shuts down gracefully.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
•Press and hold the Power button for five seconds.
The LEDs blink quickly and simultaneously to warn that power will be cut off forcibly.
The system shuts down.
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 5 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
NETGEAR ReadyNAS 312
65
ReadyNAS OS 6 Desktop Storage Systems
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the f actory default process immediately, press the Backup button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your storage system, such as Internet protocol settings and the administrator password,
to defaults.
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when a
NETGEAR technical support representative instructs you to do so.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The pass or fail result is reported using the storage system's
LEDs. Contact a NETGEAR technical support representative to interpret memory test results.
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button.
The system powers on.
4. Continue to press the Reset button until the Power button LED, USB and backup status LED, disk 1
LED, and disk 2 LED light.
5. Press the Backup button to scroll through boot mode options.
The storage system shows the boot mode options using the LEDs, as described in the following table:
NETGEAR ReadyNAS 312
66
ReadyNAS OS 6 Desktop Storage Systems
Status IndicatorBoot Mode
USB and
Backup
LED
Disk 2
LED
Disk 1
LED
Power
LED
Description
All four LEDs light.Boot menu
Power LED lights.Normal
Disk 1 LED lights.Factory default
Disk 2 LED lights.OS reinstall
USB and backup status LED lights.Tech support
Power LED and disk 1 LED light.Volume read only
Power LED and disk 2 LED light.Memory test
P ower LED and USB and bac kup status LED
light.
Test disk
Legend:
•On:
•Off:
6. Press and release the Reset button to confirm your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 312
67
ReadyNAS OS 6 Desktop Storage Systems
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 314.
Figure 24. ReadyNAS 314 front and side panels
1. Exhaust vents
2. Shared USB 2.0 and eSATA port
3. Backup button and LED
4. Disk LEDs
5. Infrared remote receiver
6. Disk activity LED
7. Power button and LED
8. Drive bay door
9. Status display screen
Drive Bays
The following figure shows the drive bays of the ReadyNAS 314.
NETGEAR ReadyNAS 314
69
ReadyNAS OS 6 Desktop Storage Systems
Figure 25. ReadyNAS 314 drive bays
1. Drive bay door
2. Disk tray handle
3. Recessed disk tray handle lock
4. Disk tray release latch
5. Drive bays
Rear Panel
The following figure shows the rear panel of the ReadyNAS 314.
NETGEAR ReadyNAS 314
70
ReadyNAS OS 6 Desktop Storage Systems
Figure 26. ReadyNAS 314 rear panel
1. Reset button
2. LAN ports with LED status indicators
3. eSATA port
4. USB 3.0 ports
5. HDMI port (currently not supported)
6. Power cable socket
7. Exhaust fan
8. Kensington lock
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
NETGEAR ReadyNAS 314
71
ReadyNAS OS 6 Desktop Storage Systems
Table 8. ReadyNAS 314 indicator descriptions
DescriptionIndicator
Press this button to turn on the ReadyNAS.The LED indicates these states:
•On. Powered on.
•Blinking. Booting or shutting down.
•Off. Powered off.
Power button and LED
An LED on the top of the front panel is associated with each drive bay. LEDs are in
numerical order from left to right.The disk LEDs indicate these states:
•On. Power is on and the disk is operating normally.
•Blinking.The disk was removed, failed, or is resynchronizing. See the display
screen for details.
•Off.The drive bay is empty.
Disk LEDs (1, 2, 3, 4)
The disk activity LED has these states:
•On. At least one disk is present.
•Blinking. A disk is active.
•Off. All disks are idle.
Disk activity LED
Two LED status indicators are built into this port, one green and one amber.They
indicate port speed and activity as follows:
•Green on, amber off. 1000 Mbps connection speed, no activity.
•Green blinking, amber off. 1000 Mbps connection speed, activity.
•Green off, amber on. 10 Mbps or 100 Mbps connection speed, no activity.
•Green off, amber blinking. 10 Mbps or 100 Mbps connection speed, activity.
•Green off, amber off. No connection.
Rear panel Ethernet port
LEDs
Displays messages about the status of your storage system. Note that the status
displa y screen goes to sleep to prevent burn-in.To wake it, press the Power button
once. If the storage system reports an abnormal operation or error , the status display
screen stays on.
Status display screen
Power On and Shut Down
This section describes how to pow er on and shut down y our system. If you m ust shut down the system, use
one of the preferred shutdown methods whenever possible.
NETGEAR ReadyNAS 314
72
ReadyNAS OS 6 Desktop Storage Systems
Power On
When you connect the system to a po wer supply or the system reco v ers from a pow er outage, the f ollo wing
occurs:
•The system automatically powers on if you enabled the Wake on LAN (WoL) feature or scheduled the
system to automatically power on or off.
•The system returns to its last state if the W ake on LAN (W oL) feature is disab led and you did not schedule
the system to automatically power on or off:
-If the system was powered on, the system automatically powers on again when the power supply
is connected or power is restored.
-If the system was powered off , the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. If the status display screen is not lit, do the following:
a. Press the Power button.
The status display screen wakes.
b. Press the Power button a second time.
Instructions for graceful shutdown display on the status display screen.
c. Press the Power button a third time.
The system shuts down gracefully.
2. If the status display screen is lit, do the following:
a. Press the Power button.
Instructions for graceful shutdown display on the status display screen.
b. Press the Power button again.
The system shuts down gracefully.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
•Press and hold the Power button on the front panel of the system for five seconds.
The LEDs blink quickly and simultaneously to warn that power will be cut off forcibly.
NETGEAR ReadyNAS 314
73
ReadyNAS OS 6 Desktop Storage Systems
The system shuts down.
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 5 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the f actory default process immediately, press the Backup button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your storage system, such as Internet protocol settings and the administrator password,
to defaults.
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when a
NETGEAR technical support representative instructs you to do so.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The pass or fail result is reported on the status display screen.
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button.
The systems powers on.
NETGEAR ReadyNAS 314
74
ReadyNAS OS 6 Desktop Storage Systems
4. Continue to press the Reset button until the status display screen shows a boot menu message.
5. Press the Backup button to scroll through boot mode options.
The status display screen shows the current boot mode option.
6. When the status display screen shows the boot mode that you need, press and release the Reset button
to confirm your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 314
75
ReadyNAS OS 6 Desktop Storage Systems
10
NETGEAR ReadyNAS 316
This chapter provides an overview of the physical features of the ReadyNAS 316 and includes the following
sections:
•Front and Side Panels on page 77
•Drive Bays on page 77
•Rear Panel on page 78
•Status Information on page 79
•Power On and Shut Down on page 80
•Boot Menu on page 81
76
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 316.
Figure 27. ReadyNAS 316 front and side panels
1. Status and menu display screen
2. Infrared remote receiver
3. Drive bay door
4. Touch pad and backlight
5. OK button
Drive Bays
The following figure shows the drive bays of the ReadyNAS 316.
NETGEAR ReadyNAS 316
77
ReadyNAS OS 6 Desktop Storage Systems
Figure 28. ReadyNAS 316 drive bays
1. Drive bay door
2. Disk tray release latch
3. Recessed disk tray handle lock
4. USB 2.0 port
5. Disk tray handle
6. Power button
7. Disk LED
8. Drive bays
Rear Panel
The following figure shows the rear panel of the ReadyNAS 316.
NETGEAR ReadyNAS 316
78
ReadyNAS OS 6 Desktop Storage Systems
Figure 29. ReadyNAS 316 rear panel
1. Exhaust fan
2. Power cable socket
3. Power switch
4. Kensington lock
5. eSATA ports
6. LAN ports with LED status indicators
7. HDMI port (currently not supported)
8. USB 3.0 ports
9. Reset button
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
NETGEAR ReadyNAS 316
79
ReadyNAS OS 6 Desktop Storage Systems
Table 9. ReadyNAS 316 indicator descriptions
DescriptionIndicator
A disk LED next to each drive bay indicates the status of the disk inside.The disk
LEDs indicate these states:
•Solid blue. Power is on and the disk is operating normally.
•Blinking blue.The disk is active.
•Solid red.The disk w as remov ed, f ailed, or is resynchronizing. See the display
screen for details.
•Off. No disk is present.
Disk LEDs
Two LED status indicators are built into this port, one green and one amber.They
indicate port speed and activity as follows:
•Green on, amber off. 1000 Mbps connection speed, no activity.
•Green blinking, amber off. 1000 Mbps connection speed, activity.
•Green off, amber on. 10 Mbps or 100 Mbps connection speed, no activity.
•Green off, amber blinking. 10 Mbps or 100 Mbps connection speed, activity.
•Green off, amber off. No connection.
Rear panel Ethernet port
LEDs
Displays messages about the status of your storage system. Note that the status
display screen goes to sleep to prevent burn-in.To wake the status display screen,
activate the proximity sensor, press the touch pad, press the OK button, or press
the Power b utton once. If the storage system reports an abnormal operation or error ,
the status display screen stays on.
Status display screen
Power On and Shut Down
This section describes how to pow er on and shut down y our system. If you m ust shut down the system, use
one of the preferred shutdown methods whenever possible.
Power On
When you connect the system to a power supply and the Power switch is in the On position or the system
recovers from a power outage and the Power switch is in the On position, the following occurs:
•The system automatically powers on if you enabled the Wake on LAN (WoL) feature or scheduled the
system to automatically power on or off.
•The system returns to its last state if the W ake on LAN (W oL) feature is disab led and you did not schedule
the system to automatically power on or off:
NETGEAR ReadyNAS 316
80
ReadyNAS OS 6 Desktop Storage Systems
-If the system was powered on, the system automatically powers on again when the power supply
is connected or power is restored.
-If the system was powered off , the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. If the status display screen is not lit, do the following:
a. Press the Power button on the front panel of the system.
The status display screen wakes.
b. Press the Power button a second time.
Instructions for graceful shutdown display on the status display screen.
c. Press the Power button a third time.
The system shuts down gracefully.
2. If the status display screen is lit, do the following:
a. Press the Power button on the front panel of the system.
Instructions for graceful shutdown display on the status display screen.
b. Press the Power button again.
The system shuts down gracefully.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
•Press and hold the Power button on the front panel of the system for five seconds.
The LEDs blink quickly and simultaneously to warn that power will be cut off forcibly.
The system shuts down.
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
NETGEAR ReadyNAS 316
81
ReadyNAS OS 6 Desktop Storage Systems
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 2 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the factory default process immediately, press the OK button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your storage system, such as Internet protocol settings and the administrator password,
to defaults.
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when a
NETGEAR technical support representative instructs you to do so.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The pass or fail result is reported on the status display screen.
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button on the front panel of the system.
The system powers on.
4. Continue to press the Reset button until the status display screen shows a boot menu message.
5. Use the arrows on the touch pad to scroll through boot mode options.
The status display screen shows the current boot mode option.
6. When the status display screen shows the boot mode that you need, press the OK button to confirm
your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 316
82
ReadyNAS OS 6 Desktop Storage Systems
11
NETGEAR ReadyNAS 422
This chapter provides an overview of the physical features of the ReadyNAS 422 and includes the following
sections:
•Front and Side Panels on page 84
•Drive Bays on page 85
•Rear Panel on page 86
•Status Information on page 87
•Power On and Shut Down on page 87
•Boot Menu on page 89
83
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 422.
Figure 30. ReadyNAS 422 front and side panels
1. Status and menu display screen
2. OK button
3. Four buttons (Up, Down, Left, Right) and backlights
4. USB 3.0 port
5. Drive bay door
NETGEAR ReadyNAS 422
84
ReadyNAS OS 6 Desktop Storage Systems
Drive Bays
The following figure shows the drive bays of ReadyNAS 422.
Figure 31. ReadyNAS 422 drive bays
1. Drive bay door
2. Disk tray handle
3. Disk tray release latch
4. USB 3.0 port
5. Recessed disk tray handle lock
6. Power button
7. Disk LED
8. Drive bays
NETGEAR ReadyNAS 422
85
ReadyNAS OS 6 Desktop Storage Systems
Rear Panel
The following figure shows the rear panel of the ReadyNAS 422.
Figure 32. Rear panel ReadyNAS 422
1. Exhaust fan
2. Kensington lock
3. eSATA port
4. USB 3.0 port
5. Micro USB console connector (marked as UART)
6. Reset button
7. 1 GbE LAN ports with LED status indicators
8. Power cable socket
NETGEAR ReadyNAS 422
86
ReadyNAS OS 6 Desktop Storage Systems
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
Table 10. Indicator descriptions ReadyNAS 422
DescriptionIndicator
Displays messages about the status of your storage system. Note that the status
display screen goes to sleep to prevent burn-in.To wake the status display screen,
press any button on the front panel. If the storage system reports an abnormal
operation or error, the status display screen stays on.
Front panel status display
screen
A disk LED next to each drive bay indicates the status of the disk inside.The disk
LEDs indicate these states:
•Solid blue. Power is on and the disk is operating normally.
•Blinking blue.The disk is active.
•Solid red.The disk was remo ved, failed, or is resynchronizing. See the display
screen for details.
•Off. No disk is present.
Drive bay disk LEDs
Two LED status indicators are b uilt into each 1G Ethernet port. One LED is a bicolor
LED that can light solid amber or solid green and indicates the port speed.The other
LED is green and indicates the link (solid green) and activity (b linking green).These
LEDs indicate port speed and activity as follows:
•Bicolor LED green, green LED solid. 1 Gbps connection speed, no activity.
•Bicolor LED green, green LED blinking. 1 Gbps connection speed, activity.
•Bicolor LED amber , green LED solid. 100 Mbps connection speed, no activity.
•Bicolor LED amber , green LED blinking. 100 Mbps connection speed, activity .
•Bicolor LED off, green LED off. Either no connection or 10 Mbps connection
without activity.
•Bicolor LED off, green LED blinking. 10 Mbps connection, activity.
Rear panel 1G Ethernet LAN
port LEDs
Power On and Shut Down
This section describes how to pow er on and shut down y our system. If you m ust shut down the system, use
one of the preferred shutdown methods whenever possible.
NETGEAR ReadyNAS 422
87
ReadyNAS OS 6 Desktop Storage Systems
Power On
When you connect the system to a power supply or the system recovers from a power outage, the system
returns to its last state:
•If the system was powered on, the system automatically powers on again when the power supply is
connected or power is restored.
•If the system was powered off, the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. If the status display screen is not lit, do the following:
a. Press the Power button on the front panel of the system.
The status display screen wakes.
b. Press the Power button a second time.
Instructions for graceful shutdown display on the status display screen.
c. Press the Power button a third time.
The system shuts down gracefully.
2. If the status display screen is lit, do the following:
a. Press the Power button on the front panel of the system.
Instructions for graceful shutdown display on the status display screen.
b. Press the Power button again.
The system shuts down gracefully.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
Press and hold the Power button on the front panel of the system for five seconds.
The LEDs blink quickly and simultaneously to warn that power will be cut off forcibly.
The system shuts down.
NETGEAR ReadyNAS 422
88
ReadyNAS OS 6 Desktop Storage Systems
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 2 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the factory default process immediately, press the OK button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your stor age system, such as IP settings and the administrator pass w ord, to def aults .
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when
instructed to do so by a NETGEAR technical support representative.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The pass or fail result is reported on the status display screen.
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button on the front panel of the system.
The system powers on.
4. Continue to press the Reset button until the status display screen shows a boot menu message.
5. Use the Up and Down buttons on the front panel to scroll through boot mode options.
NETGEAR ReadyNAS 422
89
ReadyNAS OS 6 Desktop Storage Systems
The status display screen shows the current boot mode option.
6. When the status display screen shows the boot mode that you need, press the OK button to confirm
your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 422
90
ReadyNAS OS 6 Desktop Storage Systems
12
NETGEAR ReadyNAS 424
This chapter provides an overview of the physical features of the ReadyNAS 424 and includes the following
sections:
•Front and Side Panels on page 92
•Drive Bays on page 93
•Rear Panel on page 94
•Status Information on page 95
•Power On and Shut Down on page 95
•Boot Menu on page 97
91
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 424.
Figure 33. ReadyNAS 424 front and side panels
1. Status and menu display screen
2. OK button
3. Four buttons (Up, Down, Left, Right) and backlights
4. USB 3.0 port
5. Drive bay door
NETGEAR ReadyNAS 424
92
ReadyNAS OS 6 Desktop Storage Systems
Drive Bays
The following figure shows the drive bays of ReadyNAS 424.
Figure 34. ReadyNAS 424 drive bays
1. Drive bay door
2. Disk tray handle
3. Disk tray release latch
4. Recessed disk tray handle lock
5. USB 3.0 port
6. Disk LED
7. Power button
8. Drive bays
NETGEAR ReadyNAS 424
93
ReadyNAS OS 6 Desktop Storage Systems
Rear Panel
The following figure shows the rear panel of the ReadyNAS 424.
Figure 35. Rear panel ReadyNAS 424
1. Exhaust fan
2. Kensington lock
3. eSATA port
4. USB 3.0 port
5. Micro USB console connector (marked as UART)
6. Reset button
7. 1 GbE LAN ports with LED status indicators
8. Power cable socket
NETGEAR ReadyNAS 424
94
ReadyNAS OS 6 Desktop Storage Systems
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
Table 11. Indicator descriptions ReadyNAS 424
DescriptionIndicator
Displays messages about the status of your storage system. Note that the status
display screen goes to sleep to prevent burn-in.To wake the status display screen,
press any button on the front panel. If the storage system reports an abnormal
operation or error, the status display screen stays on.
Front panel status display
screen
A disk LED next to each drive bay indicates the status of the disk inside.The disk
LEDs indicate these states:
•Solid blue. Power is on and the disk is operating normally.
•Blinking blue.The disk is active.
•Solid red.The disk was remo ved, failed, or is resynchronizing. See the display
screen for details.
•Off. No disk is present.
Drive bay disk LEDs
Two LED status indicators are b uilt into each 1G Ethernet port. One LED is a bicolor
LED that can light solid amber or solid green and indicates the port speed.The other
LED is green and indicates the link (solid green) and activity (b linking green).These
LEDs indicate port speed and activity as follows:
•Bicolor LED green, green LED solid. 1 Gbps connection speed, no activity.
•Bicolor LED green, green LED blinking. 1 Gbps connection speed, activity.
•Bicolor LED amber , green LED solid. 100 Mbps connection speed, no activity.
•Bicolor LED amber , green LED blinking. 100 Mbps connection speed, activity .
•Bicolor LED off, green LED off. Either no connection or 10 Mbps connection
without activity.
•Bicolor LED off, green LED blinking. 10 Mbps connection, activity.
Rear panel 1G Ethernet LAN
port LEDs
Power On and Shut Down
This section describes how to pow er on and shut down y our system. If you m ust shut down the system, use
one of the preferred shutdown methods whenever possible.
NETGEAR ReadyNAS 424
95
ReadyNAS OS 6 Desktop Storage Systems
Power On
When you connect the system to a power supply or the system recovers from a power outage, the system
returns to its last state:
•If the system was powered on, the system automatically powers on again when the power supply is
connected or power is restored.
•If the system was powered off, the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. If the status display screen is not lit, do the following:
a. Press the Power button on the front panel of the system.
The status display screen wakes.
b. Press the Power button a second time.
Instructions for graceful shutdown display on the status display screen.
c. Press the Power button a third time.
The system shuts down gracefully.
2. If the status display screen is lit, do the following:
a. Press the Power button on the front panel of the system.
Instructions for graceful shutdown display on the status display screen.
b. Press the Power button again.
The system shuts down gracefully.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
Press and hold the Power button on the front panel of the system for five seconds.
The LEDs blink quickly and simultaneously to warn that power will be cut off forcibly.
The system shuts down.
NETGEAR ReadyNAS 424
96
ReadyNAS OS 6 Desktop Storage Systems
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 2 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the factory default process immediately, press the OK button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your stor age system, such as IP settings and the administrator pass w ord, to def aults .
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when
instructed to do so by a NETGEAR technical support representative.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The pass or fail result is reported on the status display screen.
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button on the front panel of the system.
The system powers on.
4. Continue to press the Reset button until the status display screen shows a boot menu message.
5. Use the Up and Down buttons on the front panel to scroll through boot mode options.
NETGEAR ReadyNAS 424
97
ReadyNAS OS 6 Desktop Storage Systems
The status display screen shows the current boot mode option.
6. When the status display screen shows the boot mode that you need, press the OK button to confirm
your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 424
98
ReadyNAS OS 6 Desktop Storage Systems
13
NETGEAR ReadyNAS 426
This chapter provides an overview of the physical features of the ReadyNAS 426 and includes the following
sections:
•Front and Side Panels on page 100
•Drive Bays on page 101
•Rear Panel on page 102
•Status Information on page 103
•Power On and Shut Down on page 103
•Boot Menu on page 105
99
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 426.
Figure 36. ReadyNAS 426 front and side panels
1. Status and menu display screen
2. OK button
3. Four buttons (Up, Down, Left, Right) and backlights
4. USB 3.0 port
5. Drive bay door
NETGEAR ReadyNAS 426
100
ReadyNAS OS 6 Desktop Storage Systems
Drive Bays
The following figure shows the drive bays of ReadyNAS 426.
Figure 37. ReadyNAS 426 drive bays
1. Drive bay door
2. Disk tray release latch
3. Recessed disk tray handle lock
4. USB 3.0 port
5. Disk tray handle
6. Power button
7. Disk LED
8. Drive bays
NETGEAR ReadyNAS 426
101
ReadyNAS OS 6 Desktop Storage Systems
Rear Panel
The following figure shows the rear panel of the ReadyNAS 426.
Figure 38. ReadyNAS 426 rear panel
1. Exhaust fan
2. Power cable socket
3. Power switch
4. Kensington lock
5. eSATA port
6. USB 3.0 port
7. Four 1 GbE LAN ports with LED status indicators
8. Reset button
9. Micro USB console connector (marked as UART)
NETGEAR ReadyNAS 426
102
ReadyNAS OS 6 Desktop Storage Systems
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
Table 12. Indicator descriptions ReadyNAS 426
DescriptionIndicator
Displays messages about the status of your storage system. Note that the status
display screen goes to sleep to prevent burn-in.To wake the status display screen,
press any button on the front panel. If the storage system reports an abnormal
operation or error, the status display screen stays on.
Front panel status display
screen
A disk LED next to each drive bay indicates the status of the disk inside.The disk
LEDs indicate these states:
•Solid blue. Power is on and the disk is operating normally.
•Blinking blue.The disk is active.
•Solid red.The disk was remo ved, failed, or is resynchronizing. See the display
screen for details.
•Off. No disk is present.
Drive bay disk LEDs
Two LED status indicators are b uilt into each 1G Ethernet port. One LED is a bicolor
LED that can light solid amber or solid green and indicates the port speed.The other
LED is green and indicates the link (solid green) and activity (b linking green).These
LEDs indicate port speed and activity as follows:
•Bicolor LED green, green LED solid. 1 Gbps connection speed, no activity.
•Bicolor LED green, green LED blinking. 1 Gbps connection speed, activity.
•Bicolor LED amber , green LED solid. 100 Mbps connection speed, no activity.
•Bicolor LED off, green LED off. Either no connection or 10 Mbps connection
without activity.
•Bicolor LED off, green LED blinking. 10 Mbps connection, activity.
Rear panel 1G Ethernet LAN
port LEDs
Power On and Shut Down
This section describes how to pow er on and shut down y our system. If you m ust shut down the system, use
one of the preferred shutdown methods whenever possible.
NETGEAR ReadyNAS 426
103
ReadyNAS OS 6 Desktop Storage Systems
Power On
When you connect the system to a power supply and the Power switch is in the On position or the system
recovers from a power outage and the Power switch is in the On position, the following occurs:
•The system automatically powers on if you enabled the Wake on LAN (WoL) feature or scheduled the
system to automatically power on or off.
•The system returns to its last state if the W ake on LAN (W oL) feature is disab led and you did not schedule
the system to automatically power on or off:
-If the system was powered on, the system automatically powers on again when the power supply
is connected or power is restored.
-If the system was powered off , the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. If the status display screen is not lit, do the following:
a. Press the Power button on the front panel of the system.
The status display screen wakes.
b. Press the Power button a second time.
Instructions for graceful shutdown display on the status display screen.
c. Press the Power button a third time.
The system shuts down gracefully.
2. If the status display screen is lit, do the following:
a. Press the Power button on the front panel of the system.
Instructions for graceful shutdown display on the status display screen.
b. Press the Power button again.
The system shuts down gracefully.
NETGEAR ReadyNAS 426
104
ReadyNAS OS 6 Desktop Storage Systems
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
Press and hold the Power button on the front panel of the system for five seconds.
The LEDs blink quickly and simultaneously to warn that power will be cut off forcibly.
The system shuts down.
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 2 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the factory default process immediately, press the OK button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your stor age system, such as IP settings and the administrator pass w ord, to def aults .
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when
instructed to do so by a NETGEAR technical support representative.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The pass or fail result is reported on the status display screen.
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
NETGEAR ReadyNAS 426
105
ReadyNAS OS 6 Desktop Storage Systems
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button on the front panel of the system.
The system powers on.
4. Continue to press the Reset button until the status display screen shows a boot menu message.
5. Use the Up and Down buttons on the front panel to scroll through boot mode options.
The status display screen shows the current boot mode option.
6. When the status display screen shows the boot mode that you need, press the OK button to confirm
your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 426
106
ReadyNAS OS 6 Desktop Storage Systems
14
NETGEAR ReadyNAS 428
This chapter provides an overview of the physical features of the ReadyNAS 428 and includes the following
sections:
•Front and Side Panels on page 108
•Drive Bays on page 109
•Rear Panel on page 110
•Status Information on page 111
•Power On and Shut Down on page 111
•Boot Menu on page 113
107
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 428.
Figure 39. ReadyNAS 428 front and side panels
1. Status and menu display screen
2. OK button
3. Four buttons (Up, Down, Left, Right) and backlights
4. USB 3.0 port
5. Drive bay door
NETGEAR ReadyNAS 428
108
ReadyNAS OS 6 Desktop Storage Systems
Drive Bays
The following figure shows the drive bays of ReadyNAS 428.
Figure 40. ReadyNAS 428 drive bays
1. Drive bay door
2. Disk tray release latch
3. Recessed disk tray handle lock
4. USB 3.0 port
5. Disk tray handle
6. Power button
7. Disk LED
8. Drive bays
NETGEAR ReadyNAS 428
109
ReadyNAS OS 6 Desktop Storage Systems
Rear Panel
The following figure shows the rear panel of the ReadyNAS 428.
Figure 41. ReadyNAS 428 rear panel
1. Two exhaust fans
2. Power cable socket
3. Power switch
4. Kensington lock
5. eSATA port
6. USB 3.0 port
7. Four 1 GbE LAN ports with LED status indicators
8. Reset button
9. Micro USB console connector (marked as UART)
NETGEAR ReadyNAS 428
110
ReadyNAS OS 6 Desktop Storage Systems
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
Table 13. Indicator descriptions ReadyNAS 428
DescriptionIndicator
Displays messages about the status of your storage system. Note that the status
display screen goes to sleep to prevent burn-in.To wake the status display screen,
press any button on the front panel. If the storage system reports an abnormal
operation or error, the status display screen stays on.
Front panel status display
screen
A disk LED next to each drive bay indicates the status of the disk inside.The disk
LEDs indicate these states:
•Solid blue. Power is on and the disk is operating normally.
•Blinking blue.The disk is active.
•Solid red.The disk was remo ved, failed, or is resynchronizing. See the display
screen for details.
•Off. No disk is present.
Drive bay disk LEDs
Two LED status indicators are b uilt into each 1G Ethernet port. One LED is a bicolor
LED that can light solid amber or solid green and indicates the port speed.The other
LED is green and indicates the link (solid green) and activity (b linking green).These
LEDs indicate port speed and activity as follows:
•Bicolor LED green, green LED solid. 1 Gbps connection speed, no activity.
•Bicolor LED green, green LED blinking. 1 Gbps connection speed, activity.
•Bicolor LED amber , green LED solid. 100 Mbps connection speed, no activity.
•Bicolor LED off, green LED off. Either no connection or 10 Mbps connection
without activity.
•Bicolor LED off, green LED blinking. 10 Mbps connection, activity.
Rear panel 1G Ethernet LAN
port LEDs
Power On and Shut Down
This section describes how to pow er on and shut down y our system. If you m ust shut down the system, use
one of the preferred shutdown methods whenever possible.
NETGEAR ReadyNAS 428
111
ReadyNAS OS 6 Desktop Storage Systems
Power On
When you connect the system to a power supply and the Power switch is in the On position or the system
recov ers from a power outage and the Power s witch is in the On position, the system returns to its last state:
•If the system was powered on, the system automatically powers on again when the power supply is
connected or power is restored.
•If the system was powered off, the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. If the status display screen is not lit, do the following:
a. Press the Power button on the front panel of the system.
The status display screen wakes.
b. Press the Power button a second time.
Instructions for graceful shutdown display on the status display screen.
c. Press the Power button a third time.
The system shuts down gracefully.
2. If the status display screen is lit, do the following:
a. Press the Power button on the front panel of the system.
Instructions for graceful shutdown display on the status display screen.
b. Press the Power button again.
The system shuts down gracefully.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
Press and hold the Power button on the front panel of the system for five seconds.
The LEDs blink quickly and simultaneously to warn that power will be cut off forcibly.
The system shuts down.
NETGEAR ReadyNAS 428
112
ReadyNAS OS 6 Desktop Storage Systems
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 2 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the factory default process immediately, press the OK button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your stor age system, such as IP settings and the administrator pass w ord, to def aults .
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when
instructed to do so by a NETGEAR technical support representative.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The pass or fail result is reported on the status display screen.
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button on the front panel of the system.
The system powers on.
4. Continue to press the Reset button until the status display screen shows a boot menu message.
5. Use the Up and Down buttons on the front panel to scroll through boot mode options.
NETGEAR ReadyNAS 428
113
ReadyNAS OS 6 Desktop Storage Systems
The status display screen shows the current boot mode option.
6. When the status display screen shows the boot mode that you need, press the OK button to confirm
your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 428
114
ReadyNAS OS 6 Desktop Storage Systems
15
NETGEAR ReadyNAS 516
This chapter provides an overview of the physical features of the ReadyNAS 516 and includes the following
sections:
•Front and Side Panels on page 116
•Drive Bays on page 116
•Rear Panel on page 117
•Status Information on page 118
•Power On and Shut Down on page 119
•Boot Menu on page 120
115
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 516.
Figure 42. ReadyNAS 516 front and side panels
1. Status and menu display screen
2. Infrared remote receiver
3. Drive bay door
4. Touch pad and backlight
5. OK button
Drive Bays
The following figure shows the drive bays of the ReadyNAS 516.
NETGEAR ReadyNAS 516
116
ReadyNAS OS 6 Desktop Storage Systems
Figure 43. ReadyNAS 516 drive bays
1. Drive bay door
2. Disk tray release latch
3. Recessed disk tray handle lock
4. USB 2.0 port
5. Disk tray handle
6. Power button
7. Disk LED
8. Drive bays
Rear Panel
The following figure shows the rear panel of the ReadyNAS 516.
NETGEAR ReadyNAS 516
117
ReadyNAS OS 6 Desktop Storage Systems
Figure 44. ReadyNAS 516 rear panel
1. Exhaust fan
2. Power cable socket
3. Power switch
4. Kensington lock
5. eSATA ports
6. LAN ports with LED status indicators
7. HDMI port (currently not supported)
8. eSATA port
9. USB 3.0 ports
10. Reset button
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
NETGEAR ReadyNAS 516
118
ReadyNAS OS 6 Desktop Storage Systems
Table 14. ReadyNAS 516 indicator descriptions
DescriptionIndicator
A disk LED next to each drive bay indicates the status of the disk inside.The disk
LEDs indicate these states:
•Solid blue. Power is on and the disk is operating normally.
•Blinking blue.The disk is active.
•Solid red.The disk was remo ved, failed, or is resynchronizing. See the display
screen for details.
•Off. No disk is present.
Disk LEDs
Two LED status indicators are built into this port, one green and one amber.They
indicate port speed and activity as follows:
•Green on, amber off. 1000 Mbps connection speed, no activity.
•Green blinking, amber off. 1000 Mbps connection speed, activity.
•Green off, amber on. 10 Mbps or 100 Mbps connection speed, no activity.
•Green off, amber blinking. 10 Mbps or 100 Mbps connection speed, activity.
•Green off, amber off. No connection.
Rear panel Ethernet port
LEDs
Displays messages about the status of your storage system. Note that the status
display screen goes to sleep to prevent burn-in.To wake the status display screen,
activate the proximity sensor, press the touch pad, press the OK button, or press
the Power b utton once. If the storage system reports an abnormal operation or error ,
the status display screen stays on.
Status display screen
Power On and Shut Down
This section describes how to pow er on and shut down y our system. If you m ust shut down the system, use
one of the preferred shutdown methods whenever possible.
Power On
When you connect the system to a power supply and the Power switch is in the On position or the system
recovers from a power outage and the Power switch is in the On position, the following occurs:
•The system automatically powers on if you enabled the Wake on LAN (WoL) feature or scheduled the
system to automatically power on or off.
•The system returns to its last state if the W ake on LAN (W oL) feature is disab led and you did not schedule
the system to automatically power on or off:
NETGEAR ReadyNAS 516
119
ReadyNAS OS 6 Desktop Storage Systems
-If the system was powered on, the system automatically powers on again when the power supply
is connected or power is restored.
-If the system was powered off , the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. If the status display screen is not lit, do the following:
a. Press the Power button on the front panel of the system.
The status display screen wakes.
b. Press the Power button a second time.
Instructions for graceful shutdown display on the status display screen.
c. Press the Power button a third time.
The system shuts down gracefully.
2. If the status display screen is lit, do the following:
a. Press the Power button on the front panel of the system.
Instructions for graceful shutdown display on the status display screen.
b. Press the Power button again.
The system shuts down gracefully.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
•Press and hold the Power button on the front panel of the system for five seconds.
The LEDs blink quickly and simultaneously to warn that power will be cut off forcibly.
The system shuts down.
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
NETGEAR ReadyNAS 516
120
ReadyNAS OS 6 Desktop Storage Systems
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 2 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the factory default process immediately, press the OK button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your storage system, such as Internet protocol settings and the administrator password,
to defaults.
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when a
NETGEAR technical support representative instructs you to do so.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The pass or fail result is reported on the status display screen.
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button on the front panel of the system.
The system powers on.
4. Continue to press the Reset button until the status display screen shows a boot menu message.
5. Use the arrows on the touch pad to scroll through boot mode options.
The status display screen shows the current boot mode option.
6. When the status display screen shows the boot mode that you need, press the OK button to confirm
your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 516
121
ReadyNAS OS 6 Desktop Storage Systems
16
NETGEAR ReadyNAS 524X
This chapter provides an overview of the physical features of the ReadyNAS 524X and includes the following
sections:
•Front and Side Panels on page 123
•Drive Bays on page 124
•Rear Panel on page 125
•Status Information on page 126
•Power On and Shut Down on page 127
•Boot Menu on page 128
122
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 524X.
Figure 45. ReadyNAS 524X front and side panels
1. Status and menu display screen
2. OK button
3. Four buttons (Up, Down, Left, Right) and backlights
4. USB 3.0 port
5. Drive bay door
NETGEAR ReadyNAS 524X
123
ReadyNAS OS 6 Desktop Storage Systems
Drive Bays
The following figure shows the drive bays of ReadyNAS 524X.
Figure 46. ReadyNAS 524X drive bays
1. Drive bay door
2. Disk tray handle
3. Disk tray release latch
4. Recessed disk tray handle lock
5. USB 3.0 port
6. Disk LED
7. Power button
8. Drive bays
NETGEAR ReadyNAS 524X
124
ReadyNAS OS 6 Desktop Storage Systems
Rear Panel
The following figure shows the rear panel of the ReadyNAS 524X.
Figure 47. Rear panel ReadyNAS 524X
1. Exhaust fan
2. Kensington lock
3. eSATA port
4. USB 3.0 ports
5. Micro USB console connector (marked as UART)
6. Reset button
7. 1 GbE LAN port with LED status indicators
8. 10 GbE LAN port with LED status indicators
9. Power cable socket
NETGEAR ReadyNAS 524X
125
ReadyNAS OS 6 Desktop Storage Systems
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
Table 15. Indicator descriptions ReadyNAS 524X
DescriptionIndicator
Displays messages about the status of your storage system. Note that the status
display screen goes to sleep to prevent burn-in.To wake the status display screen,
press any button on the front panel. If the storage system reports an abnormal
operation or error, the status display screen stays on.
Front panel status display
screen
A disk LED next to each drive bay indicates the status of the disk inside.The disk
LEDs indicate these states:
•Solid blue. Power is on and the disk is operating normally.
•Blinking blue.The disk is active.
•Solid red.The disk was remo ved, failed, or is resynchronizing. See the display
screen for details.
•Off. No disk is present.
Drive bay disk LEDs
NETGEAR ReadyNAS 524X
126
ReadyNAS OS 6 Desktop Storage Systems
Table 15. Indicator descriptions ReadyNAS 524X (Continued)
DescriptionIndicator
Two LED status indicators are b uilt into each 1G Ethernet port. One LED is a bicolor
LED that can light solid amber or solid green and indicates the port speed.The other
LED is green and indicates the link (solid green) and activity (b linking green).These
LEDs indicate port speed and activity as follows:
•Bicolor LED green, green LED solid. 1 Gbps connection speed, no activity.
•Bicolor LED green, green LED blinking. 1 Gbps connection speed, activity.
•Bicolor LED amber , green LED solid. 100 Mbps connection speed, no activity.
•Bicolor LED amber , green LED blinking. 100 Mbps connection speed, activity .
•Bicolor LED off, green LED off. Either no connection or 10 Mbps connection
without activity.
•Bicolor LED off, green LED blinking. 10 Mbps connection, activity.
Rear panel 1G Ethernet LAN
port LEDs
Two LED status indicators are b uilt into each 10G Ethernet port. One LED is a bicolor
LED that can light solid amber or solid green and indicates the port speed.The other
LED is green and indicates the link (solid green) and activity (b linking green).These
LEDs indicate port speed and activity as follows:
•Bicolor LED green, green LED solid. 1 Gbps connection speed, no activity.
•Bicolor LED green, green LED blinking. 1 Gbps connection speed, activity.
•Bicolor LED amber, green LED solid. 10 Gbps connection speed, no activity.
•Bicolor LED amber, green LED blinking. 10 Gbps connection speed, activity.
•Bicolor LED off, green LED off. No connection.
Rear panel 10G Ethernet
LAN port LEDs
Power On and Shut Down
This section describes how to pow er on and shut down y our system. If you m ust shut down the system, use
one of the preferred shutdown methods whenever possible.
Power On
When you connect the system to a power supply or the system recovers from a power outage, the system
returns to its last state:
•If the system was powered on, the system automatically powers on again when the power supply is
connected or power is restored.
•If the system was powered off, the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
NETGEAR ReadyNAS 524X
127
ReadyNAS OS 6 Desktop Storage Systems
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. If the status display screen is not lit, do the following:
a. Press the Power button on the front panel of the system.
The status display screen wakes.
b. Press the Power button a second time.
Instructions for graceful shutdown display on the status display screen.
c. Press the Power button a third time.
The system shuts down gracefully.
2. If the status display screen is lit, do the following:
a. Press the Power button on the front panel of the system.
Instructions for graceful shutdown display on the status display screen.
b. Press the Power button again.
The system shuts down gracefully.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
Press and hold the Power button on the front panel of the system for five seconds.
The LEDs blink quickly and simultaneously to warn that power will be cut off forcibly.
The system shuts down.
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 2 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
NETGEAR ReadyNAS 524X
128
ReadyNAS OS 6 Desktop Storage Systems
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the factory default process immediately, press the OK button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your stor age system, such as IP settings and the administrator pass w ord, to def aults .
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when
instructed to do so by a NETGEAR technical support representative.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The pass or fail result is reported on the status display screen.
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button on the front panel of the system.
The system powers on.
4. Continue to press the Reset button until the status display screen shows a boot menu message.
5. Use the Up and Down buttons on the front panel to scroll through boot mode options.
The status display screen shows the current boot mode option.
6. When the status display screen shows the boot mode that you need, press the OK button to confirm
your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 524X
129
ReadyNAS OS 6 Desktop Storage Systems
17
NETGEAR ReadyNAS 526X and 626X
This chapter provides an overview of the physical features of the ReadyNAS 526X and 626X and includes the
following sections:
•Front and Side Panels on page 131
•Drive Bays on page 132
•Rear Panel ReadyNAS 526X on page 133
•Rear Panel ReadyNAS 626X on page 134
•Status Information on page 135
•Power On and Shut Down on page 136
•Boot Menu on page 137
130
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 526X and 626X.
Figure 48. ReadyNAS 526X and 626X front and side panels
1. Status and menu display screen
2. OK button
3. Four buttons (Up, Down, Left, Right) and backlights
4. USB 3.0 port
5. Drive bay door
NETGEAR ReadyNAS 526X and 626X
131
ReadyNAS OS 6 Desktop Storage Systems
Drive Bays
The following figure shows the drive bays of ReadyNAS 526X AND 626X.
Figure 49. ReadyNAS 526X and 626X drive bays
1. Drive bay door
2. Disk tray release latch
3. Recessed disk tray handle lock
4. USB 3.0 port
5. Disk tray handle
6. Power button
7. Disk LED
8. Drive bays
NETGEAR ReadyNAS 526X and 626X
132
ReadyNAS OS 6 Desktop Storage Systems
Rear Panel ReadyNAS 526X
The following figure shows the rear panel of the ReadyNAS 526X.
Figure 50. Rear panel ReadyNAS 526X
1. Exhaust fan
2. Power cable socket
3. Power switch
4. Kensington lock
5. eSATA port
6. USB 3.0 ports
7. 10 GbE LAN ports with LED status indicators
8. Reset button
NETGEAR ReadyNAS 526X and 626X
133
ReadyNAS OS 6 Desktop Storage Systems
Rear Panel ReadyNAS 626X
The following figure shows the rear panel of the ReadyNAS 626X.
Figure 51. Rear panel ReadyNAS 626X
1. Exhaust fan
2. Power cable socket
3. Power switch
4. Kensington lock
5. eSATA port
6. USB 3.0 ports
7. 1 GbE LAN ports with LED status indicators
8. 10 GbE LAN ports with LED status indicators
9. Reset button
NETGEAR ReadyNAS 526X and 626X
134
ReadyNAS OS 6 Desktop Storage Systems
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
Table 16. Indicator descriptions ReadyNAS 526X and 626X
DescriptionIndicator
Displays messages about the status of your storage system. Note that the status
display screen goes to sleep to prevent burn-in.To wake the status display screen,
press any button on the front panel. If the storage system reports an abnormal
operation or error, the status display screen stays on.
Front panel status display
screen
A disk LED next to each drive bay indicates the status of the disk inside.The disk
LEDs indicate these states:
•Solid blue. Power is on and the disk is operating normally.
•Blinking blue.The disk is active.
•Solid red.The disk was remo ved, failed, or is resynchronizing. See the display
screen for details.
•Off. No disk is present.
Drive bay disk LEDs
NETGEAR ReadyNAS 526X and 626X
135
ReadyNAS OS 6 Desktop Storage Systems
Table 16. Indicator descriptions ReadyNAS 526X and 626X (Continued)
DescriptionIndicator
Two LED status indicators are b uilt into each 1G Ethernet port. One LED is a bicolor
LED that can light solid amber or solid green and indicates the port speed.The other
LED is green and indicates the link (solid green) and activity (b linking green).These
LEDs indicate port speed and activity as follows:
•Bicolor LED green, green LED solid. 1 Gbps connection speed, no activity.
•Bicolor LED green, green LED blinking. 1 Gbps connection speed, activity.
•Bicolor LED amber , green LED solid. 100 Mbps connection speed, no activity.
•Bicolor LED off, green LED off. Either no connection or 10 Mbps connection
without activity.
•Bicolor LED off, green LED blinking. 10 Mbps connection, activity.
Model RN626X only:
Rear panel 1G Ethernet LAN
port LEDs
Two LED status indicators are b uilt into each 10G Ethernet port. One LED is a bicolor
LED that can light solid amber or solid green and indicates the port speed.The other
LED is green and indicates the link (solid green) and activity (b linking green).These
LEDs indicate port speed and activity as follows:
•Bicolor LED green, green LED solid. 1 Gbps connection speed, no activity.
•Bicolor LED green, green LED blinking. 1 Gbps connection speed, activity.
•Bicolor LED amber, green LED solid. 10 Gbps connection speed, no activity.
•Bicolor LED amber, green LED blinking. 10 Gbps connection speed, activity.
•Bicolor LED off, green LED off. No connection.
Rear panel 10G Ethernet
LAN port LEDs
Power On and Shut Down
This section describes how to pow er on and shut down y our system. If you m ust shut down the system, use
one of the preferred shutdown methods whenever possible.
Power On
When you connect the system to a power supply and the Power switch is in the On position or the system
recovers from a power outage and the Power switch is in the On position, the following occurs:
•The system automatically powers on if you enabled the Wake on LAN (WoL) feature or scheduled the
system to automatically power on or off.
•The system returns to its last state if the W ake on LAN (W oL) feature is disab led and you did not schedule
the system to automatically power on or off:
NETGEAR ReadyNAS 526X and 626X
136
ReadyNAS OS 6 Desktop Storage Systems
-If the system was powered on, the system automatically powers on again when the power supply
is connected or power is restored.
-If the system was powered off , the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. If the status display screen is not lit, do the following:
a. Press the Power button on the front panel of the system.
The status display screen wakes.
b. Press the Power button a second time.
Instructions for graceful shutdown display on the status display screen.
c. Press the Power button a third time.
The system shuts down gracefully.
2. If the status display screen is lit, do the following:
a. Press the Power button on the front panel of the system.
Instructions for graceful shutdown display on the status display screen.
b. Press the Power button again.
The system shuts down gracefully.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
Press and hold the Power button on the front panel of the system for five seconds.
The LEDs blink quickly and simultaneously to warn that power will be cut off forcibly.
The system shuts down.
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
NETGEAR ReadyNAS 526X and 626X
137
ReadyNAS OS 6 Desktop Storage Systems
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 2 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the factory default process immediately, press the OK button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your stor age system, such as IP settings and the administrator pass w ord, to def aults .
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when
instructed to do so by a NETGEAR technical support representative.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The pass or fail result is reported on the status display screen.
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button on the front panel of the system.
The system powers on.
4. Continue to press the Reset button until the status display screen shows a boot menu message.
5. Use the Up and Down buttons on the front panel to scroll through boot mode options.
The status display screen shows the current boot mode option.
6. When the status display screen shows the boot mode that you need, press the OK button to confirm
your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 526X and 626X
138
ReadyNAS OS 6 Desktop Storage Systems
18
NETGEAR ReadyNAS 528X and 628X
This chapter provides an overview of the physical features of the ReadyNAS 528X and 628X and includes the
following sections:
•Front and Side Panels on page 140
•Drive Bays on page 141
•Rear Panel ReadyNAS 528X on page 142
•Rear Panel ReadyNAS 628X on page 143
•Status Information on page 144
•Power On and Shut Down on page 145
•Boot Menu on page 146
139
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 528X and 628X.
Figure 52. ReadyNAS 528X and 628X front and side panels
1. Status and menu display screen
2. OK button
3. Four buttons (Up, Down, Left, Right) and backlights
4. USB 3.0 port
5. Drive bay door
NETGEAR ReadyNAS 528X and 628X
140
ReadyNAS OS 6 Desktop Storage Systems
Drive Bays
The following figure shows the drive bays of ReadyNAS 528X AND 628X.
Figure 53. ReadyNAS 528X and 628X drive bays
1. Drive bay door
2. Disk tray release latch
3. Recessed disk tray handle lock
4. USB 3.0 port
5. Disk tray handle
6. Power button
7. Disk LED
8. Drive bays
NETGEAR ReadyNAS 528X and 628X
141
ReadyNAS OS 6 Desktop Storage Systems
Rear Panel ReadyNAS 528X
The following figure shows the rear panel of the ReadyNAS 528X.
Figure 54. Rear panel ReadyNAS 528X
1. Exhaust fan
2. Power cable socket
3. Power switch
4. Kensington lock
5. eSATA port
6. USB 3.0 ports
7. 10 GbE LAN ports with LED status indicators
8. Reset button
9. Micro USB console connector (marked as UART)
NETGEAR ReadyNAS 528X and 628X
142
ReadyNAS OS 6 Desktop Storage Systems
Rear Panel ReadyNAS 628X
The following figure shows the rear panel of the ReadyNAS 628X.
Figure 55. Rear panel ReadyNAS 628X
1. Exhaust fan
2. Power cable socket
3. Power switch
4. Kensington lock
5. eSATA port
6. USB 3.0 ports
7. 1 GbE LAN ports with LED status indicators
8. 10 GbE LAN ports with LED status indicators
9. Reset button
10. Micro USB console connector (marked as UART)
NETGEAR ReadyNAS 528X and 628X
143
ReadyNAS OS 6 Desktop Storage Systems
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
Table 17. Indicator descriptions ReadyNAS 528X and 628X
DescriptionIndicator
Displays messages about the status of your storage system. Note that the status
display screen goes to sleep to prevent burn-in.To wake the status display screen,
press any button on the front panel. If the storage system reports an abnormal
operation or error, the status display screen stays on.
Front panel status display
screen
A disk LED next to each drive bay indicates the status of the disk inside.The disk
LEDs indicate these states:
•Solid blue. Power is on and the disk is operating normally.
•Blinking blue.The disk is active.
•Solid red.The disk was remo ved, failed, or is resynchronizing. See the display
screen for details.
•Off. No disk is present.
Drive bay disk LEDs
NETGEAR ReadyNAS 528X and 628X
144
ReadyNAS OS 6 Desktop Storage Systems
Table 17. Indicator descriptions ReadyNAS 528X and 628X (Continued)
DescriptionIndicator
Two LED status indicators are b uilt into each 1G Ethernet port. One LED is a bicolor
LED that can light solid amber or solid green and indicates the port speed.The other
LED is green and indicates the link (solid green) and activity (b linking green).These
LEDs indicate port speed and activity as follows:
•Bicolor LED green, green LED solid. 1 Gbps connection speed, no activity.
•Bicolor LED green, green LED blinking. 1 Gbps connection speed, activity.
•Bicolor LED amber , green LED solid. 100 Mbps connection speed, no activity.
•Bicolor LED off, green LED off. Either no connection or 10 Mbps connection
without activity.
•Bicolor LED off, green LED blinking. 10 Mbps connection, activity.
Model RN628X only:
Rear panel 1G Ethernet LAN
port LEDs
Two LED status indicators are b uilt into each 10G Ethernet port. One LED is a bicolor
LED that can light solid amber or solid green and indicates the port speed.The other
LED is green and indicates the link (solid green) and activity (b linking green).These
LEDs indicate port speed and activity as follows:
•Bicolor LED green, green LED solid. 1 Gbps connection speed, no activity.
•Bicolor LED green, green LED blinking. 1 Gbps connection speed, activity.
•Bicolor LED amber, green LED solid. 10 Gbps connection speed, no activity.
•Bicolor LED amber, green LED blinking. 10 Gbps connection speed, activity.
•Bicolor LED off, green LED off. No connection.
Rear panel 10G Ethernet
LAN port LEDs
Power On and Shut Down
This section describes how to pow er on and shut down y our system. If you m ust shut down the system, use
one of the preferred shutdown methods whenever possible.
Power On
When you connect the system to a power supply and the Power switch is in the On position or the system
recov ers from a power outage and the Power s witch is in the On position, the system returns to its last state:
•If the system was powered on, the system automatically powers on again when the power supply is
connected or power is restored.
•If the system was powered off, the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
NETGEAR ReadyNAS 528X and 628X
145
ReadyNAS OS 6 Desktop Storage Systems
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. If the status display screen is not lit, do the following:
a. Press the Power button on the front panel of the system.
The status display screen wakes.
b. Press the Power button a second time.
Instructions for graceful shutdown display on the status display screen.
c. Press the Power button a third time.
The system shuts down gracefully.
2. If the status display screen is lit, do the following:
a. Press the Power button on the front panel of the system.
Instructions for graceful shutdown display on the status display screen.
b. Press the Power button again.
The system shuts down gracefully.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
Press and hold the Power button on the front panel of the system for five seconds.
The LEDs blink quickly and simultaneously to warn that power will be cut off forcibly.
The system shuts down.
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 2 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
NETGEAR ReadyNAS 528X and 628X
146
ReadyNAS OS 6 Desktop Storage Systems
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the factory default process immediately, press the OK button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your stor age system, such as IP settings and the administrator pass w ord, to def aults .
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when
instructed to do so by a NETGEAR technical support representative.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The pass or fail result is reported on the status display screen.
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button on the front panel of the system.
The system powers on.
4. Continue to press the Reset button until the status display screen shows a boot menu message.
5. Use the Up and Down buttons on the front panel to scroll through boot mode options.
The status display screen shows the current boot mode option.
6. When the status display screen shows the boot mode that you need, press the OK button to confirm
your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 528X and 628X
147
ReadyNAS OS 6 Desktop Storage Systems
19
NETGEAR ReadyNAS 716X
This chapter provides an overview of the physical features of the ReadyNAS 716X and includes the following
sections:
•Front and Side Panels on page 149
•Drive Bays on page 149
•Rear Panel on page 150
•Status Information on page 151
•Power On and Shut Down on page 153
•Boot Menu on page 154
148
Front and Side Panels
The following figure shows the front and side panels of the ReadyNAS 716X.
Figure 56. ReadyNAS 716X front and side panels
1. Status and menu display screen
2. Infrared remote receiver
3. Drive bay door
4. Touch pad and backlight
5. OK button
Drive Bays
The following figure shows the drive bays of ReadyNAS 716X.
NETGEAR ReadyNAS 716X
149
ReadyNAS OS 6 Desktop Storage Systems
Figure 57. ReadyNAS 716X drive bays
1. Drive bay door
2. Disk tray release latch
3. Recessed disk tray handle lock
4. USB 2.0 port
5. Disk tray handle
6. Power button
7. Disk LED
8. Drive bays
Rear Panel
The following figure shows the rear panel of ReadyNAS 716X.
NETGEAR ReadyNAS 716X
150
ReadyNAS OS 6 Desktop Storage Systems
Figure 58. ReadyNAS 716X rear panel
1. Exhaust fan
2. Power cable socket
3. Power switch
4. Kensington lock
5. eSATA ports
6. 1 Gb LAN ports with LED status indicators
7. HDMI port
8. eSATA port
9. USB 3.0 ports
10. Reset button
11. 10 Gb LAN ports with LED status indicators
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
NETGEAR ReadyNAS 716X
151
ReadyNAS OS 6 Desktop Storage Systems
Table 18. ReadyNAS 716X indicator descriptions
DescriptionIndicator
A disk LED next to each drive bay indicates the status of the disk inside.The disk
LEDs indicate these states:
•Solid blue. Power is on and the disk is operating normally.
•Blinking blue.The disk is active.
•Solid red.The disk was remo ved, failed, or is resynchronizing. See the display
screen for details.
•Off. No disk is present.
Disk LEDs
Two LED status indicators are built into this port, one green and one amber.They
indicate port speed and activity as follows:
•Green on, amber off. 1000 Mbps connection speed, no activity.
•Green blinking, amber off. 1000 Mbps connection speed, activity.
•Green off, amber on. 10 Mbps or 100 Mbps connection speed, no activity.
•Green off, amber blinking. 10 Mbps or 100 Mbps connection speed, activity.
•Green off, amber off. No connection.
Rear panel Ethernet port
LEDs (1 Gb)
NETGEAR ReadyNAS 716X
152
ReadyNAS OS 6 Desktop Storage Systems
Table 18. ReadyNAS 716X indicator descriptions (Continued)
DescriptionIndicator
Two LED status indicators are b uilt into this port.The y indicate port speed and activity
as follows:
•LED 1
Off. No link.
Solid green. Linked.
Blinking green. Activity.
•LED 2
Solid green. 10 GbE.
Solid yellow. 1 GbE.
Off. 100 Mbps.
Rear panel Ethernet port
LEDs (10 Gb)
Displays messages about the status of your storage system. Note that the status
display screen goes to sleep to prevent burn-in.To wake the status display screen,
activate the proximity sensor, press the touch pad, press the OK button, or press
the Power b utton once. If the storage system reports an abnormal operation or error ,
the status display screen stays on.
Status display screen
Power On and Shut Down
This section describes how to pow er on and shut down y our system. If you m ust shut down the system, use
one of the preferred shutdown methods whenever possible.
Power On
When you connect the system to a power supply and the Power switch is in the On position or the system
recovers from a power outage and the Power switch is in the On position, the following occurs:
•The system automatically powers on if you enabled the Wake on LAN (WoL) feature or scheduled the
system to automatically power on or off.
•The system returns to its last state if the W ake on LAN (W oL) feature is disab led and you did not schedule
the system to automatically power on or off:
NETGEAR ReadyNAS 716X
153
ReadyNAS OS 6 Desktop Storage Systems
-If the system was powered on, the system automatically powers on again when the power supply
is connected or power is restored.
-If the system was powered off , the system remains off when the power supply is connected or power
is restored.
In this situation, press the Power button on the front panel of the system to power on the system.
Preferred Shutdown
You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.
F or inf ormation about how to gracefully shut do wn your system using the ReadyNAS local admin page , see
the ReadyNAS OS 6 Software Manual, which is av ailable at netgear.com/support/product/ReadyNAS_OS_6.
To gracefully shut down your system using the Power button:
1. If the status display screen is not lit, do the following:
a. Press the Power button on the front panel of the system.
The status display screen wakes.
b. Press the Power button a second time.
Instructions for graceful shutdown display on the status display screen.
c. Press the Power button a third time.
The system shuts down gracefully.
2. If the status display screen is lit, do the following:
a. Press the Power button on the front panel of the system.
Instructions for graceful shutdown display on the status display screen.
b. Press the Power button again.
The system shuts down gracefully.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
•Press and hold the Power button on the front panel of the system for five seconds.
The LEDs blink quickly and simultaneously to warn that power will be cut off forcibly.
The system shuts down.
Boot Menu
Use the boot menu to restart or troubleshoot y our ReadyNAS stor age system.Your storage system has the
following boot modes:
NETGEAR ReadyNAS 716X
154
ReadyNAS OS 6 Desktop Storage Systems
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a short disk test that takes approximately 2 minutes. After the disk test, a
10-minute time-out period begins, during which all LEDs blink simultaneously.
WARNING:
The factory default reboot process resets the storage system to factory
settings, erases all data, resets all defaults, and reformats the disk to X-RAID .
-If you w ant to cancel the factory default process , power off the stor age system before the 10-min ute
time-out ends.The system powers down safely without causing any data loss.
-If you want to reset the system to factory default settings, do not power off your system. After the
10-minute time-out period, the factory default process begins.
To start the factory default process immediately, press the OK button during the
10-minute time-out period.
Tip
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode
when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets
some settings on your storage system, such as Internet protocol settings and the administrator password,
to defaults.
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when
instructed to do so by a NETGEAR technical support representative.
•Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue
data off a disk during a disaster recovery.
•Memory test. Performs a memory test.The pass or fail result is reported on the status display screen.
•Test disk. Performs an offline full disk test.This process can take four hours or more, depending on
the size of y our disks. Any problems are reported in the system logs. F or more information about viewing
the system logs, see the ReadyNAS OS 6 Software Manual, which is available at
netgear.com/support/product/ReadyNAS_OS_6.
To access the boot menu:
1. Power off your storage system.
2. Using a straightened paper clip, press and hold the Reset button.
3. Press the Power button on the front panel of the system.
The system powers on.
4. Continue to press the Reset button until the status display screen shows a boot menu message.
5. Use the arrows on the touch pad to scroll through boot mode options.
The status display screen shows the current boot mode option.
6. When the status display screen shows the boot mode that you need, press the OK button to confirm
your boot menu selection.
The system boots in the selected boot mode.
NETGEAR ReadyNAS 716X
155
ReadyNAS OS 6 Desktop Storage Systems
20
NETGEAR EDA 500
This chapter provides an overview of the physical features of the EDA 500 and includes the following sections:
•Front and Side Panels on page 157
•Drive Bays on page 157
•Rear Panel on page 158
•Status Information on page 159
•Power On and Shut Down on page 160
The ED A 500 disk tr a ys are slightly different from the standard tra ys. Use only EDA 500 disk
trays with the EDA 500. For more information about the EDA 500 disk trays, see EDA 500
Disk Tray on page 164.
Note
A ReadyNAS cannot boot using the disks in an EDA 500. All disks in a RAID volume must be either in a ReadyNAS
or in an EDA 500. A RAID volume cannot combine disks in a ReadyNAS with disks in an EDA 500.
You can add an EDA 500 to a ReadyNAS while the ReadyNAS is running, but you cannot remove the EDA
while the ReadyNAS is running.
You can add and remove disks while an EDA 500 is in oper ation (hot swap). If an added disk has data on it, the
data shows as an inactive volume.You need to destroy inactive volumes, which destroys all data in the volume ,
and create new volumes, before the space is available for use by the ReadyNAS.
156
Front and Side Panels
The following figure shows the front and side panels of EDA 500.
Figure 59. EDA 500 front and side panels
1. Power LED
2. eSATA LED
3. Volume LED
4. Alert LED
5. Drive bay door
Drive Bays
The following figure shows the drive bays of EDA 500.
NETGEAR EDA 500
157
ReadyNAS OS 6 Desktop Storage Systems
Figure 60. EDA 500 drive bays
1. Drive bay door
2. Disk tray release latch
3. Recessed disk tray handle lock
4. Disk tray handle
5. Power button
6. Disk LED
7. Disk label
8. Active drive bays
9. Cold spare drive bay
Rear Panel
The following figure shows the rear panel of EDA 500.
NETGEAR EDA 500
158
ReadyNAS OS 6 Desktop Storage Systems
Figure 61. EDA 500 rear panel
1. Exhaust fan
2. Kensington lock
3. Power switch
4. Power cable socket
5. eSATA port
Status Information
You can obtain information about the status of your storage system by reviewing the indicators listed in the
following table.
NETGEAR EDA 500
159
ReadyNAS OS 6 Desktop Storage Systems
Table 19. EDA 500 indicator descriptions
DescriptionIndicator
The Power LED indicates these states:
•On. Powered on.
•Off. Powered off.
Power LED
The eSATA LED indicates these states:
•On.The SATA link is established between the EDA 500 and a host.
•Off.The SATA link is not established.
eSATA LED
The Volume LED indicates these states:
•On.The data volume or volumes are mounted by a host.
•Off.The data volume or volumes are not mounted.You can safely disconnect
the eSATA cable.
Volume LED
The Alert LED indicates these states:
•On.The system needs attention. Use the local admin page to determine the
problem. For more information, see the ReadyNAS OS 6 Software Manual,
which is available at netgear.com/support/product/ReadyNAS_OS_6.
•Off.The system is healthy.
Alert LED
A disk LED next to each active drive bay indicates the status of the disk inside.
(The cold spare drive bay has no LED.) The disk LEDs indicate these states:
•Solid blue. Power is on and the disk is operating normally.
•Blinking blue.The disk is active.
•Solid red.The disk was remo ved, failed, or is resynchronizing. See the display
screen for details.
•Off. No disk is present.
Disk LEDs
Power On and Shut Down
This section describes how to pow er on and shut down y our system. If you m ust shut down the system, use
the preferred shutdown method whenever possible.
Power On
When the system is connected to a power supply and the Power switch is in the On position, the system
automatically powers on.
NETGEAR EDA 500
160
ReadyNAS OS 6 Desktop Storage Systems
When connected to a host that is pow ered on, the EDA 500 automatically powers on.The ED A 500 detects
a powered-on host through the eSATA link.
You can also power on the system by pressing the Power button on the front panel of the system.
Preferred Shutdown
If possible, always unmount the EDA 500 volumes from the host before shutting down the EDA 500.
Use the ReadyNAS local admin page to gracefully shut down the EDA 500. For information about how to
gracefully shut down the ED A 500 using the ReadyNAS local admin page, see the ReadyNAS OS 6 Software
Manual, which is available at netgear.com/support/product/ReadyNAS_OS_6.
Forced Shutdown
Perform a forced shutdown only if the storage system is not responding.
To perform a forced shutdown:
•Flip the Power switch on the back panel of the system to the Off position.
NETGEAR EDA 500
161
ReadyNAS OS 6 Desktop Storage Systems
21
Disks
This chapter describes how to reformat, add, and replace disks in your ReadyNAS OS 6 storage system.
For information about configuring disks on your storage system, see the ReadyNAS OS 6 Software Manual,
which is available at netgear.com/support/product/ReadyNAS_OS_6.
This chapter includes the following topics:
•Disk Trays on page 163
•Supported Disks on page 164
•Previously Formatted Disks on page 165
•Add a Disk on page 166
•Replace a Disk on page 175
162
Disk Trays
All systems except the EDA 500 use standard disk trays.The EDA 500 comes with its own special disk
trays.This section describes both the standard and EDA 500 disk trays.
For some disks, first remove the plastic mounting bracket from the disk tray before
you mount the disk to the disk tray. After you mount the disk to the disk tray, use the
screws to secure the disk to the disk tray.
Note
Standard Disk Tray
The f ollowing figure sho ws the f eatures of the standard disk tr a y.This disk tra y is used in all systems e xcept
the EDA 500. For information about the EDA 500 disk tray, see EDA 500 Disk Tray on page 164.
Figure 62. Standard disk tray
1. Disk tray
2. Disk tray release latch
3. Recessed disk tray handle lock
4. Disk tray handle
5. Disk screw holes
6. Mounting bracket
7. Bracket lock
IMPORTANT:
To maintain adequate airflow , make sure that all disk tra ys remain in the drive
bays, even if no disk is installed in the tray. Do not use standard disk trays
with the EDA 500. Use only EDA 500 disk trays with the EDA 500.
Disks
163
ReadyNAS OS 6 Desktop Storage Systems
EDA 500 Disk Tray
The following figure shows the features of the EDA 500 disk tray.The EDA 500 disk tray and the standard
disk tray are the same, except for the EMI shielding on the EDA 500 disk tray. For this reason, use only
EDA 500 disk trays with the EDA 500.
Figure 63. EDA 500 disk tray
1. Disk tray
2. Disk tray release latch
3. Recessed disk tray handle lock
4. Disk tray handle
5. Disk screw holes
6. Mounting bracket
7. Bracket lock
8. EMI shielding
IMPORTANT:
Use only ED A 500 disk tra ys with the ED A 500. Do not use standar d disk trays
with the EDA 500.
To maintain adequate airflow , make sure that all disk tra ys remain in the drive
bays, even if no disk is installed in the tray.
Supported Disks
Use only supported SATA hard disk drives (HDD) or solid state drives (SSD) in your ReadyNAS storage
system. If you use disks that are not supported, NETGEAR technical support will not provide assistance.
For a list of supported disks, see the NETGEAR Hardware Compatibility List at netgear.com/readynas-hcl.
Disks
164
ReadyNAS OS 6 Desktop Storage Systems
Previously Formatted Disks
This section describes how to use previously formatted disks with your ReadyNAS OS 6 storage system.
Previously formatted disks must appear on the NETGEAR Hardware Compatibility List, which is available
at netgear.com/readynas-hcl.
Reformat Previously Formatted Disks
If you want to use disks that were previously formatted for an operating system other than ReadyNAS OS
6 (for example, Windows or RAIDiator), you must reformat the disks.
If you w ant to use disks from another ReadyNAS OS 6 storage system, see Migr ate a Volume on page 166.
If you try to use previously f ormatted disks in a system that does not contain any other
disks, the system does not boot and ReadyCLOUD does not disco ver your device. If
you use RAIDar to discover your device, RAIDar displays a "Corrupt Root" error
message.
If you try to use previously formatted disks in a system that already contains usable
disks, the system does not reformat or use the previously formatted disks. Any data
on the previously formatted disk remains intact.
Note
The following instructions describe how to reformat previously f ormatted disks in a ReadyNAS OS 6 system.
This procedure assumes that the system does not contain any other disks.
To reformat previously formatted disks with a diskless ReadyNAS OS 6 system:
1. Gracefully shut down the storage system.
F or information about how to gracefully shut do wn your system, see the Preferred Shutdo wn section of
the chapter that describes your system.
2. Install the disks.
For more information, see Add a Disk on page 166.
3. Reset the system to its factory default settings.
WARNING:
This process erases all data and reformats all disks into a single X-RAID
volume. If you want to preserve the data on the disks, you must back up the
data to an external drive before using the disks in your ReadyNAS storage
system.
F or inf ormation about how to reset the system to its factory default settings , see the Boot Menu section
of the chapter that describes your system.
The disk is reformatted and becomes available for use with your ReadyNAS OS 6 storage system.
Disks
165
ReadyNAS OS 6 Desktop Storage Systems
Migrate a Volume
You can migrate a volume from one ReadyNAS OS 6 storage system to another, as long as you migrate
every disk in the volume. For example, if you want to migrate a volume that contains two disks, you must
add both disks to the new system. If y ou add only part of a volume to the new system, the system recogniz es
the disk as a degraded volume.
If your ReadyNAS stor age system is oper ating with one or more disks, you can add disks while the system
is running.The ne w system recognizes the migrated v olume and its data. For more inf ormation about adding
a disk while the system is running, see Add a Disk on page 166.
If your ReadyNAS storage system does not have any disks installed, perform the following procedure.
To migrate a volume to a diskless ReadyNAS OS 6 system:
1. Gracefully shut down the new (diskless) storage system.
F or information about how to gracefully shut do wn your system, see the Preferred Shutdo wn section of
the chapter that describes your system.
2. Remove each disk in the volume from the old system.
3. Install each disk in the volume into the new storage system.
For more information, see Add a Disk on page 166.
4. Turn on the new system by pressing the Power button.
The new system recognizes the migrated volume and its data.
Add a Disk
You can add a 3.5-inch hard disk drive , a 2.5-inch hard disk drive, or a 2.5-inch solid state driv e to an empty
drive bay.
If you want to add a previously formatted disk to your storage system, see the instructions in Previously
Formatted Disks on page 165.
Add a 3.5-Inch Disk
To add a 3.5-inch hard disk drive (HDD):
1. Determine whether you must shut down your system:
•If you are adding disks to a diskless system, gracefully shut down the system.
F or information about how to gr acefully shut down y our system, see the Pref erred Shutdown section
of the chapter that describes your system.
•If your system is operating with one or more disks, you can add disks while the system is running.
You do not need to shut down the system.
2. If necessary, slide the recessed handle lock to the unlocked position.
Disks
166
ReadyNAS OS 6 Desktop Storage Systems
3. Press the disk tray release latch.
The disk tray handle pops out.
4. Pull out the disk tray.
5. Separate the mounting bracket from the disk tray:
a. Press and hold the disk tray release latch.
b. While holding the release latch, use your other hand to pull out one end of the mounting bracket
and then the other until the ends extend slightly past the disk tray.
Disks
167
ReadyNAS OS 6 Desktop Storage Systems
Make sure that the ends of the mounting bracket are even with each other.
c. Slide the bracket down the disk tray, keeping both sides of the bracket even with each other.
The mounting bracket stops when it hits the bracket lock.
The bracket lock prevents the mounting bracket from sliding all the way off the disk tray.
6. Attach the new HDD to the mounting bracket.
Disks
168
ReadyNAS OS 6 Desktop Storage Systems
Make sure that the HDD mounting holes are aligned with the brack et's mounting posts and that the HDD
connectors face the interior of the disk tray.
Disks
169
ReadyNAS OS 6 Desktop Storage Systems
7. Push the mounting bracket and HDD back into the disk tray.
WARNING:
To prevent damage to your system, make sure that the disk tray is correctly
oriented before inserting it into the drive bay.
8. Insert the disk tray back into the drive bay of the storage system.
•For 2-ba y and 4-bay systems, insert the disk tray so that the disk tra y release latch is near the bottom
of the system.
•For 6-bay systems, insert the disk tray so that the disk tray release latch is on the left side of the
system.
9. Press down on the disk tray handle until it latches closed.
The disk tray is secured in the drive bay.
10. If necessary, turn on your system by pressing the Power button.
If the disk that you added w as not pre viously f ormatted, the system uses the disk in one of the follo wing
ways:
Disks
170
ReadyNAS OS 6 Desktop Storage Systems
•If you are adding the disk to a system that uses X-RAID, the system automatically determines whether
the disk is used for protection or storage.The new disk is incorporated in the background while you
continue to use your system.
•If you are adding the disk to a system that uses Flex-RAID, the disk becomes available for use.You
use the local admin page to manually configure the new disk.
For more information about X-RAID, Flex-RAID, and using the local admin page, see the ReadyNAS
OS 6 Software Manual, which is available at netgear.com/support/product/ReadyNAS_OS_6.
Add a 2.5-Inch Disk
To add a 2.5-inch hard disk drive (HDD) or 2.5-inch solid state drive (SSD):
1. Determine whether you must shut down your system:
•If you are adding disks to a diskless system, gracefully shut down the system.
F or information about how to gr acefully shut down y our system, see the Pref erred Shutdown section
of the chapter that describes your system.
•If your system is operating with one or more disks, you can add disks while the system is running.
You do not need to shut down the system.
2. If necessary, slide the recessed handle lock to the unlocked position.
3. Press the disk tray release latch.
The disk tray handle pops out.
4. Pull out the disk tray.
5. Remove the mounting bracket from the disk tray:
Disks
171
ReadyNAS OS 6 Desktop Storage Systems
a. Press and hold the disk tray release latch.
b. While holding the release latch, use your other hand to pull out one end of the mounting bracket
and then the other until the ends extend slightly past the disk tray.
Make sure that the ends of the mounting bracket are even with each other.
c. Slide the bracket down the disk tray, keeping both sides of the bracket even with each other.
The mounting bracket stops when it hits the bracket lock.
The bracket lock prevents the mounting bracket from sliding all the way off the disk tray.
Disks
172
ReadyNAS OS 6 Desktop Storage Systems
d. Push the mounting bracket out of each bracket lock using a pointed object, such as a pen.
The mounting bracket is released from the bracket locks.
e. Slide the mounting bracket out of the disk tray.
The mounting bracket is not used to secure 2.5-inch HDDs or SSDs.
6. Place the new 2.5-inch HDD or SSD in the disk tray.
7. Secure the HDD or SSD to the disk tray using the screws that came with your storage system.
Make sure that the HDD or SSD connectors face the interior of the disk tray.
Disks
173
ReadyNAS OS 6 Desktop Storage Systems
Make sure that the HDD or SSD is installed on the correct side of the disk tray.
WARNING:
To prevent damage to your system, make sure that the disk tray is correctly
oriented before inserting it into the drive bay.
8. Insert the disk tray back into the drive bay of the storage system.
•For 2-ba y and 4-bay systems, insert the disk tray so that the disk tra y release latch is near the bottom
of the system.
•For 6-bay systems, insert the disk tray so that the disk tray release latch is on the left side of the
system.
9. Press down on the disk tray handle until it latches closed.
The disk tray is secured in the drive bay.
10. If necessary, turn on your system by pressing the Power button.
If the disk that you added w as not pre viously f ormatted, the system uses the disk in one of the follo wing
ways:
•If you are adding the disk to a system that uses X-RAID, the system automatically determines whether
the disk is used for protection or storage.The new disk is incorporated in the background while you
continue to use your system.
•If you are adding the disk to a system that uses Flex-RAID, the disk becomes available for use.You
use the local admin page to manually configure the new disk.
For more information about X-RAID, Flex-RAID, and using the local admin page, see the ReadyNAS
OS 6 Software Manual, which is available at netgear.com/support/product/ReadyNAS_OS_6.
Disks
174
ReadyNAS OS 6 Desktop Storage Systems
Replace a Disk
If your volumes use a protected RAID configuration, your system can recover from the failure of a disk.
When you replace the failed disk, the system rebuilds the volume using the new disk and no data from the
volume is lost.
The Disk LEDs can help you identify a failed disk. For more information, see the Status Information section
of the chapter that describes your system.You can also use the local admin page to set up email alerts that
notify you when a disk fails. In addition, the local admin page provides information about the failed disk.
F or inf ormation about RAID configurations, setting up email alerts, and using the local admin page, see the
ReadyNAS OS 6 Software Manual, which is available at netgear.com/support/product/ReadyNAS_OS_6.
ReadyNAS supports hot-swap drive bays, so you do not need to power down your storage system when
replacing a disk.
If you are replacing a disk with a previously formatted disk, see the instructions in Previously Formatted
Disks on page 165.
WARNING:
Replace one disk at a time.W ait for the v olume to resynchr onize your data bef ore
replacing another disk. If you attempt to replace more than one disk at a time, the
system will crash.
Replace a 3.5-Inch Disk
To replace a 3.5-inch hard disk drive (HDD):
1. If necessary, slide the recessed handle lock to the unlocked position.
2. Press the disk tray release latch.
The disk tray handle pops out.
Disks
175
ReadyNAS OS 6 Desktop Storage Systems
3. Pull out the disk tray.
4. Press and hold the disk tray release latch.
5. While holding the disk tray release latch, pull out the mounting bracket and slide the bracket down the
tray.
The mounting bracket stops when it hits the bracket lock.
Disks
176
ReadyNAS OS 6 Desktop Storage Systems
The bracket lock prevents the mounting bracket from sliding all the way off the disk tray.
6. Remove the old HDD from the mounting bracket.
7. Attach the new HDD to the mounting bracket.
Disks
177
ReadyNAS OS 6 Desktop Storage Systems
Make sure that the HDD mounting holes are aligned with the brack et's mounting posts and that the HDD
connectors face the interior of the disk tray.
Disks
178
ReadyNAS OS 6 Desktop Storage Systems
8. Push the mounting bracket and HDD back into the disk tray.
WARNING:
To prevent damage to your system, make sure that the disk tray is correctly
oriented before inserting it into the drive bay.
9. Insert the disk tray back into the drive bay of the storage system.
•For 2-ba y and 4-bay systems, insert the disk tray so that the disk tra y release latch is near the bottom
of the system.
•For 6-bay systems, insert the disk tray so that the disk tray release latch is on the left side of the
system.
10. Press down on the disk tray handle until it latches closed.
The disk tray is secured in the drive bay.
If the volume that contained the f ailed disk uses a protected RAID configuration, the system automatically
resynchronizes the v olume using the ne w disk. Resynchronization might take se v eral hours , depending
on the disk size.You can continue to use your storage system, although access is slower until the
volume resynchronization finishes.
Disks
179
ReadyNAS OS 6 Desktop Storage Systems
For more information about RAID configurations, see the ReadyNAS OS 6 Software Manual, which is
available at netgear.com/support/product/ReadyNAS_OS_6.
Replace a 2.5-Inch Disk
To replace a 2.5-inch hard disk drive (HDD) or 2.5-inch solid state drive (SSD):
1. If necessary, slide the recessed handle lock to the unlocked position.
2. Press the disk tray release latch.
The tray handle pops out.
3. Pull out the disk tray.
4. Replace the 2.5-inch HDD or SSD:
Disks
180
ReadyNAS OS 6 Desktop Storage Systems
a. Remove the screws and the old 2.5-inch HDD or SSD.
b. Place the new 2.5-inch HDD or SSD in the disk tray.
c. Secure the HDD or SSD to the disk tray using the screws.
Make sure that the disk connectors face the interior of the disk tray.
Disks
181
ReadyNAS OS 6 Desktop Storage Systems
Make sure that the HDD or SSD is installed on the correct side of the disk tray.
WARNING:
T o prevent damage to your system, make sure that the disk tray is correctly
oriented before inserting it into the drive bay.
5. Insert the disk tray back into the drive bay of the storage system.
•For 2-ba y and 4-bay systems, insert the disk tray so that the disk tra y release latch is near the bottom
of the system.
•For 6-bay systems, insert the disk tray so that the disk tray release latch is on the left side of the
system.
6. Press down on the disk tray handle until it latches closed.
The disk tray is secured in the drive bay.
If the volume that contained the f ailed disk uses a protected RAID configuration, the system automatically
resynchronizes the v olume using the ne w disk. Resynchronization might take se v eral hours , depending
on the disk size.You can continue to use your storage system, although access is slower until the
volume resynchronization finishes.
For more information about RAID configurations, see the ReadyNAS OS 6 Software Manual, which is
available at netgear.com/support/product/ReadyNAS_OS_6.
Disks
182
ReadyNAS OS 6 Desktop Storage Systems
A
Defaults and Technical Specifications
This appendix includes the following sections:
•Factory Default Settings on page 184
•ReadyNAS 102 Technical Specifications on page 184
•ReadyNAS 104 Technical Specifications on page 186
•ReadyNAS 202 Technical Specifications on page 187
•ReadyNAS 212 Technical Specifications on page 188
•ReadyNAS 204 Technical Specifications on page 189
•ReadyNAS 214 Technical Specifications on page 191
•ReadyNAS 312 Technical Specifications on page 192
•ReadyNAS 314 Technical Specifications on page 193
•ReadyNAS 316 Technical Specifications on page 194
•ReadyNAS 422 Technical Specifications on page 196
•ReadyNAS 424 Technical Specifications on page 197
•ReadyNAS 516 Technical Specifications on page 201
•ReadyNAS 524X Technical Specifications on page 202
•ReadyNAS 526X Technical Specifications on page 204
•ReadyNAS 528X Technical Specifications on page 205
•ReadyNAS 626X Technical Specifications on page 206
•ReadyNAS 628X Technical Specifications on page 208
•ReadyNAS 716X Technical Specifications on page 209
•EDA 500 Technical Specifications on page 210
•Safety Warnings on page 211
183
Factory Default Settings
The following table lists factory default settings for ReadyNAS OS 6 desktop storage systems.
Table 20. ReadyNAS OS 6 factory default settings
DefaultFeature
Login
The default IP address for the ReadyNAS is assigned by
the local router (DHCP server).
If a router does not assign an IP address, the ReadyNAS
defaults to the IP address https://169.254.x.x, where the
last two octets are randomly generated based on the
system's MAC address.
Default IP address
adminAdmin user name (case-sensitive)
passwordAdmin login password (case-sensitive)
Management
ReadyNAS local admin page web-based configuration and
status monitoring
System configuration
ReadyCloud for Windows, Mac, and LinuxDiscovery , setup , and multi-storage system
status monitoring web
LAN Connections
See product labelMAC address
1500MTU size
Auto Sense 10/100/1000BASE-T, RJ-45Ethernet port
DHCP acquiredLAN IP address
ReadyNAS 102 Technical Specifications
The ReadyNAS 102 storage system meets the following technical specifications:
General:
•Marvell Armada 370 1.2 GHz CPU
•512 MB memory
•Two-bay storage
•One eSATA port
Defaults and Technical Specifications
184
ReadyNAS OS 6 Desktop Storage Systems
•One USB 2.0 port (front)
•Two USB 3.0 ports (back)
•One GbE port
Physical dimensions (h x w x d):
142 x 101 x 220 mm (5.60 x 3.98 x 8.70 in.)
Physical weight:
2.12 kg (4.67 lb) without disks
Power consumption:
•BTU at full power supply utilization: 31.7W
•In operation: 31W
•Power off (Wake On LAN): 1.0W
•Power off: 210 mW
Electrical:
•External 60 W (12V, 5A) AC power supply
•Input: 100–240V AC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 92 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B
Defaults and Technical Specifications
185
ReadyNAS OS 6 Desktop Storage Systems
ReadyNAS 104 Technical Specifications
The ReadyNAS 104 storage system meets the following technical specifications:
General:
•Marvell Armada 370 1.2 GHz CPU
•512 MB memory
•Four-bay storage
•One eSATA port
•One USB 2.0 port (front)
•Two USB 3.0 ports (back)
•Two GbE ports
•LCD display
Physical dimensions (h x w x d):
205 x 134 x 223 mm (8.97 x 5.28 x 8.78 in.)
Physical weight:
4.70 kg (10.36 lb) without disks
Power consumption:
•BTU at full power supply utilization: 47W
•In operation: 45.6W
•Power off (Wake On LAN): 1.4W
•Power off: 0.44 W
Electrical:
•External 90 W (12V, 7A) AC power supply
•Input: 100–240VAC, 50/60 Hz
Defaults and Technical Specifications
186
ReadyNAS OS 6 Desktop Storage Systems
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 92 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B
ReadyNAS 202 Technical Specifications
The ReadyNAS 202 storage system meets the following technical specifications:
General:
•Annapurna Labs AL212 1.4 GHz processor
•2 GB memory
•Two-bay storage
•One eSATA port
•One USB 3.0 port (front)
•Two USB 3.0 ports (back)
•Two GbE ports
Physical dimensions (h x w x d):
142 x 101 x 220 mm (5.60 x 3.98 x 8.70 in.)
Physical weight:
2.12 kg (4.67 lb) without disks
Defaults and Technical Specifications
187
ReadyNAS OS 6 Desktop Storage Systems
Power consumption:
•BTU at full power supply utilization: 39.5W
•In operation: 38W
•Power off (Wake On LAN): 1.31W
Electrical:
•External 60 W (12V, 5A) AC power supply
•Input: 100–240 VAC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 92 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B, CCC
ReadyNAS 212 Technical Specifications
The ReadyNAS 212 storage system meets the following technical specifications:
General:
•Annapurna Labs AL214 1.4 GHz processor
•2 GB memory
•Two-bay storage
•One eSATA port
•One USB 3.0 port (front)
•Two USB 3.0 ports (back)
•Two GbE ports
Defaults and Technical Specifications
188
ReadyNAS OS 6 Desktop Storage Systems
Physical dimensions (h x w x d):
142 x 101 x 220 mm (5.60 x 3.98 x 8.70 in.)
Physical weight:
2.12 kg (4.67 lb) without disks
Power consumption:
•BTU at full power supply utilization: 39.5W
•In operation: 38W
•Power off (Wake On LAN): 1.31W
Electrical:
•External 60W (12V, 5A) AC power supply
•Input: 100–240 VAC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 92 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B, CCC
ReadyNAS 204 Technical Specifications
The ReadyNAS 204 storage system meets the following technical specifications:
General:
•Annapurna Labs AL212 1.4 GHz processor
•2 GB memory
Defaults and Technical Specifications
189
ReadyNAS OS 6 Desktop Storage Systems
•Four-bay storage
•One eSATA port
•One USB 2.0 port (front)
•Two USB 3.0 ports (back)
•Two GbE ports
•LCD display
Physical dimensions (h x w x d):
205 x 134 x 223 mm (8.97 x 5.28 x 8.78 in.)
Physical weight:
4.70 kg (10.36 lb) without disks
Power consumption:
•BTU at full power supply utilization: 48.7W
•In operation: 46.8W
•Power off (Wake On LAN): 1.31W
Electrical:
•External 90W (12V, 7A) AC power supply
•Input: 100–240 VAC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 92 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B, CCC
Defaults and Technical Specifications
190
ReadyNAS OS 6 Desktop Storage Systems
ReadyNAS 214 Technical Specifications
The ReadyNAS 214 storage system meets the following technical specifications:
General:
•Annapurna Labs AL214 1.4 GHz processor
•2 GB memory
•Four-bay storage
•One eSATA port
•One USB 2.0 port (front)
•Two USB 3.0 ports (back)
•Two GbE ports
•LCD display
Physical dimensions (h x w x d):
205 x 134 x 223 mm (8.97 x 5.28 x 8.78 in.)
Physical weight:
4.70 kg (10.36 lb) without disks
Power consumption:
•BTU at full power supply utilization: 48.7W
•In operation: 46.8W
•Power off (Wake On LAN): 1.31W
Electrical:
•External 90W (12V, 7A) AC power supply
•Input: 100–240 VAC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
Defaults and Technical Specifications
191
ReadyNAS OS 6 Desktop Storage Systems
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 92 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B, CCC
ReadyNAS 312 Technical Specifications
The ReadyNAS 312 storage system meets the following technical specifications:
General:
•Intel Atom 2.1 GHz Dual Core CPU
•2 GB memory
•Two-bay storage
•One eSATA port
•One HDMI port (not currently supported)
•One USB 2.0 port (front)
•Two USB 3.0 ports (back)
•Two LAN ports
•Infrared remote receiver
Physical dimensions (h x w x d):
142 x 101 x 220 mm (5.60 x 3.98 x 8.70 in.)
Physical weight:
2.22 kg (4.89 lb) without disks
Power consumption:
•BTU at full power supply utilization: 50.58W
•In operation: 34.92W
•Power off (Wake On LAN): 627.07 mW
•Power off: 266.61 mW
Defaults and Technical Specifications
192
ReadyNAS OS 6 Desktop Storage Systems
Electrical:
•External 60 W (12V, 5A) AC power supply
•Input: 100–240 VAC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 92 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B
ReadyNAS 314 Technical Specifications
The ReadyNAS 314 storage system meets the following technical specifications:
General:
•Intel Atom 2.1 GHz Dual Core CPU
•2 GB memory
•Four-bay storage
•Two eSATA ports (one shared USB 2.0 and eSATA port)
•One HDMI port (not currently supported)
•One USB 2.0 port (front)
•Two USB 3.0 ports (back)
•Two LAN ports
•LCD display
•Infrared remote receiver
Physical dimensions (h x w x d):
205 x 134 x 223 mm (8.97 x 5.28 x 8.78 in.)
Defaults and Technical Specifications
193
ReadyNAS OS 6 Desktop Storage Systems
Physical weight:
3.97 kg (8.75 lb) without disks
Power consumption:
•BTU at full power supply utilization: 69.45W
•In operation: 48.71 W
•Power off (Wake On LAN): 843.36 mW
•Power off: 472.77 mW
Electrical:
•External 90W (12V, 7A) AC power supply
•Input: 100–240 VAC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 92 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B
ReadyNAS 316 Technical Specifications
The ReadyNAS 316 storage system meets the following technical specifications:
General:
•Intel Atom 2.1 GHz Dual Core CPU
•2 GB memory
•Six-bay storage
•Two eSATA ports
Defaults and Technical Specifications
194
ReadyNAS OS 6 Desktop Storage Systems
•One HDMI port (not currently supported)
•One USB 2.0 port (front)
•Two USB 3.0 ports (back)
•Two LAN ports
•LCD display
•Infrared remote receiver
•Proximity sensor
Physical dimensions (h x w x d):
259 x 192 x 287.5 mm (10.20 x 7.56 x 11.32 in.)
Physical weight:
7.49 kg (16.50 lb) without disks
Power consumption:
•BTU at full power supply utilization: 110.66W
•In operation: 54.94W
•Power off (Wake On LAN): 804.64 mW
•Power off: 338.42 mW
Electrical:
•Internal 200W server-rated AC power supply
•Input: 100-240 VAC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 120 mm chassis cooling fan
Defaults and Technical Specifications
195
ReadyNAS OS 6 Desktop Storage Systems
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B
ReadyNAS 422 Technical Specifications
The ReadyNAS 422 storage system meets the following technical specifications:
General:
•Intel Atom C3338 Dual Core Processor
•2 GB DDR4 memory
•Two-bay storage
•One eSATA port
•Two USB 3.0 ports (one on the front and one on the back)
•Two 1 GbE LAN ports
•One micro USB console connector (marked as UART)
•OLED display
Physical dimensions (h x w x d):
194 x 135.5 x 239 mm (7.64 x 5.3 x 9.4 in.)
Physical weight:
3.52 kg (7.76 lb) without disks
Power consumption:
•BTU at full power supply utilization: 40.15W
•In operation: 34.86W
•Power off (Wake On LAN): 4.5W
•Power off: 270 mW
Electrical:
•External 60W AC power supply
•Input: 100–240 VAC, 50/60 Hz
Defaults and Technical Specifications
196
ReadyNAS OS 6 Desktop Storage Systems
Environmental requirements:
•Operating temperature: 0 to 45°C (32° to 113°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 92 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B
ReadyNAS 424 Technical Specifications
The ReadyNAS 424 storage system meets the following technical specifications:
General:
•Intel Atom C3338 Dual Core Processor
•2 GB DDR4 memory
•Four-bay storage
•One eSATA port
•Two USB 3.0 ports (one on the front and one on the back)
•Two 1 GbE LAN ports
•One micro USB console connector (marked as UART)
•OLED display
Physical dimensions (h x w x d):
194 x 185 x 239 mm (7.64 x 7.3 x 9.4 in.)
Physical weight:
3.95 kg (8.7 lb) without disks
Defaults and Technical Specifications
197
ReadyNAS OS 6 Desktop Storage Systems
Power consumption:
•BTU at full power supply utilization: 57.4W
•In operation: 43.09W
•Power off (Wake On LAN): 4.4W
•Power off: 400 mW
Electrical:
•External 90W AC power supply
•Input: 100–240 VAC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 45°C (32° to 113°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 120 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B
ReadyNAS 426 Technical Specifications
The ReadyNAS 426 storage system meets the following technical specifications:
General:
•Intel Atom C3538 Quad Core Processor, 2.1 GHz
•4 GB DDR4 memory
•Six-bay storage
•One eSATA port
•One USB 3.0 port (front)
•One USB 3.0 port (back)
•Four 1 GbE LAN ports
Defaults and Technical Specifications
198
ReadyNAS OS 6 Desktop Storage Systems
•One micro USB console connector (marked as UART)
•OLED display
Physical dimensions (h x w x d):
259 x 192 x 277 mm (10.2 x 7.55 x 10.9 in.)
Physical weight:
7.43 kg (16.38 lb) without disks
Power consumption:
•BTU at full power supply utilization: 68.57W
•In operation: 63.11W
•Power off (Wake On LAN): 4.313W
•Power off: 189 mW
Electrical:
•Internal 200W server-rated AC power supply
•Input: 100–240 VAC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 45°C (32° to 113°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 120 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B, CCC, MIC, BIS
Defaults and Technical Specifications
199
ReadyNAS OS 6 Desktop Storage Systems
ReadyNAS 428 Technical Specifications
The ReadyNAS 428 storage system meets the following technical specifications:
General:
•Intel Atom C3538 Quad Core Processor, 2.1 GHz
•4 GB DDR4 memory
•Eight-bay storage
•One eSATA port
•One USB 3.0 port (front)
•One USB 3.0 port (back)
•Four 1 GbE LAN ports
•One micro USB console connector (marked as UART)
•OLED display
Physical dimensions (h x w x d):
310 x 192 x 278 mm (12.2 x 7.55 x 10.94 in.)
Physical weight:
9.01 kg (19.86 lb) without disks
Power consumption:
•BTU at full power supply utilization: 91.47W
•In operation: 78.15W
•Power off (Wake On LAN): 3.995W
•Power off: 189 mW
Electrical:
•Internal 200W server-rated AC power supply
•Input: 100–240 VAC, 50/60 Hz
Defaults and Technical Specifications
200
ReadyNAS OS 6 Desktop Storage Systems
Environmental requirements:
•Operating temperature: 0 to 45°C (32° to 113°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Two software-controlled 92 mm chassis cooling fans
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B, CCC, MIC, BIS
ReadyNAS 516 Technical Specifications
The ReadyNAS 516 storage system meets the following technical specifications:
General:
•Intel Core i3 3.3 GHz Dual Core CPU
•4 GB ECC memory
•Six-bay storage
•Three eSATA ports
•One HDMI port
•One USB 2.0 port (front)
•Two USB 3.0 ports (back)
•Two LAN ports
•LCD display
•Infrared remote receiver
•Proximity sensor
Physical dimensions (h x w x d):
259 x 192 x 287.5 mm (10.20 x 7.56 x 11.32 in.)
Physical weight:
8.00 kg (17.60 lb) without disks
Defaults and Technical Specifications
201
ReadyNAS OS 6 Desktop Storage Systems
Power consumption:
•BTU at full power supply utilization: 153.54W
•In operation: 87.69W
•Power off (Wake On LAN): 798.08 mW
•Power off: 416.77 mW
Electrical:
•Internal 200W server-rated AC power supply
•Input: 100–240 VAC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 120 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B
ReadyNAS 524X Technical Specifications
The ReadyNAS 524X storage system meets the following technical specifications:
General:
•Intel Pentium processor D-1508
•4 GB ECC DDR4 memory
•Four-bay storage
•One eSATA port
•One USB 3.0 port (front)
•Two USB 3.0 ports (back)
•One 1 GbE LAN port
•One 10 GbE LAN port
Defaults and Technical Specifications
202
ReadyNAS OS 6 Desktop Storage Systems
•One micro USB console connector (marked as UART)
•OLED display
Physical dimensions (h x w x d):
194 x 185 x 239 mm (7.64 x 7.28 x 9.4 in.)
Physical weight:
4.53 kg (10.0 lb) without disks
Power consumption:
•BTU at full power supply utilization: 74.9W
•In operation: 41.9W
•Power off (Wake On LAN): 5.3W
•Power off: 204 mW
Electrical:
•External 120W AC power supply
•Input: 100–240 VAC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 92 mm or 120 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B, CCC, MIC, BIS
Defaults and Technical Specifications
203
ReadyNAS OS 6 Desktop Storage Systems
ReadyNAS 526X Technical Specifications
The ReadyNAS 526X storage system meets the following technical specifications:
General:
•Intel Pentium processor D-1508
•4 GB ECC DDR4 memory
•Six-bay storage
•One eSATA port
•One USB 3.0 port (front)
•Two USB 3.0 ports (back)
•Two 10 GbE LAN ports
•OLED display
Physical dimensions (h x w x d):
260 x 190 x 280 mm (10.24 x 7.48 x 11.02 in.)
Physical weight:
7.9 kg (17.4 lb) without disks
Power consumption:
•BTU at full power supply utilization: 100W
•In operation: 70.5W
•Power off (Wake On LAN): 310 mW
•Power off: 264 mW
Electrical:
•Internal 200W server-rated AC power supply
•Input: 100–240 VAC, 50/60 Hz
Defaults and Technical Specifications
204
ReadyNAS OS 6 Desktop Storage Systems
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 120 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B, CCC, MIC, BIS
ReadyNAS 528X Technical Specifications
The ReadyNAS 528X storage system meets the following technical specifications:
General:
•Intel Pentium processor D-1508
•4 GB ECC DDR4 memory
•Eight-bay storage
•One eSATA port
•One USB 3.0 port (front)
•Two USB 3.0 ports (back)
•Two 10 GbE LAN ports
•One micro USB console connector (marked as UART)
•OLED display
Physical dimensions (h x w x d):
319 x 192 x 289 mm (12.56 x 7.56 x 11.38 in.) with feet
Physical weight:
9.35 kg (20.61 lb) without disks
Defaults and Technical Specifications
205
ReadyNAS OS 6 Desktop Storage Systems
Power consumption:
•BTU at full power supply utilization: 104.3W
•In operation: 82.2W
•Power off (Wake On LAN): 344 mW
•Power off: 341 mW
Electrical:
•Internal 250W server-rated AC power supply
•Input: 100–240 VAC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 120 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B, CCC, MIC, BIS
ReadyNAS 626X Technical Specifications
The ReadyNAS 626X storage system meets the following technical specifications:
General:
•Intel Xeon processor D-1521
•8 GB ECC DDR4 memory
•Six-bay storage
•One eSATA port
•One USB 3.0 port (front)
•Two USB 3.0 ports (back)
•Two 1 GbE LAN ports
Defaults and Technical Specifications
206
ReadyNAS OS 6 Desktop Storage Systems
•Two 10 GbE LAN ports
•OLED display
Physical dimensions (h x w x d):
260 x 190 x 280 mm (10.24 x 7.48 x 11.02 in.)
Physical weight:
7.9 kg (17.4 lb) without disks
Power consumption:
•BTU at full power supply utilization: 100W
•In operation: 70.5W
•Power off (Wake On LAN): 310 mW
•Power off: 264 mW
Electrical:
•Internal 200W server-rated AC power supply
•Input: 100–240 VAC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 120 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B, CCC, MIC, BIS
Defaults and Technical Specifications
207
ReadyNAS OS 6 Desktop Storage Systems
ReadyNAS 628X Technical Specifications
The ReadyNAS 628X storage system meets the following technical specifications:
General:
•Intel Xeon processor D-1521
•8 GB ECC DDR4 memory
•Eight-bay storage
•One eSATA port
•One USB 3.0 port (front)
•Two USB 3.0 ports (back)
•Two 1 GbE LAN ports
•Two 10 GbE LAN ports
•One micro USB console connector (marked as UART)
•OLED display
Physical dimensions (h x w x d):
319 x 192 x 289 mm (12.56 x 7.56 x 11.38 in.) with feet
Physical weight:
9.35 kg (20.61 lb) without disks
Power consumption:
•BTU at full power supply utilization: 104.3W
•In operation: 82.2W
•Power off (Wake On LAN): 344 mW
•Power off: 341 mW
Electrical:
•Internal 250W server-rated AC power supply
•Input: 100–240 VAC, 50/60 Hz
Defaults and Technical Specifications
208
ReadyNAS OS 6 Desktop Storage Systems
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 120 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B, CCC, MIC, BIS
ReadyNAS 716X Technical Specifications
The ReadyNAS 716X storage system meets the following technical specifications:
General:
•Intel Xeon processor E3-1265L v2 CPU
•16 GB ECC memory
•Six-bay storage
•Three eSATA ports
•One HDMI port
•One USB 2.0 port (front)
•Two USB 3.0 ports (back)
•Two 1 GbE LAN ports
•Two 10 GbE LAN ports
•LCD display
•Infrared remote receiver
•Proximity sensor
Physical dimensions (h x w x d):
259 x 192 x 287.5 mm (10.20 x 7.56 x 11.32 in.)
Physical weight:
8.20 kg (18.04 lb) without disks
Defaults and Technical Specifications
209
ReadyNAS OS 6 Desktop Storage Systems
Power consumption:
•BTU at full power supply utilization: 172.79W
•In operation: 96.15W
•Power off (Wake On LAN): 799.89 mW
•Power off: 419.62 mW
Electrical:
•Internal 200W server-rated AC power supply
•Input: 100–240 VAC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software-controlled 120 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B
EDA 500 Technical Specifications
The EDA 500 storage system meets the following technical specifications:
General:
•Five-bay storage
•One eSATA port
•Proximity sensor
Physical dimensions (h x w x d):
259 x 192 x 287.5 mm (10.20 x 7.56 x 11.32 in.)
Defaults and Technical Specifications
210
ReadyNAS OS 6 Desktop Storage Systems
Physical weight:
7.3 kg (16.1 lb) without disks
Power consumption:
•BTU at full power supply utilization: 88.17W
•In operation: 37.3W
•Power off: 453.8 mW
Electrical:
•Internal 200W server-rated AC power supply
•Input: 100–240 VAC, 50/60 Hz
Environmental requirements:
•Operating temperature: 0 to 40°C (32° to 104°F)
•Operating humidity: 20 to 80% relative humidity (noncondensing)
•Storage temperature: –20 to 70°C (–4 to 158°F)
•Storage humidity: 5 to 95% relative humidity (noncondensing)
•Software controlled 120 mm chassis cooling fan
Certifications:
FCC Class B, CE Class B, RoHS, VCCI Class B
Safety Warnings
•The equipment contains no operator access areas and is certified for installation only by trained personnel,
according to the installation instructions provided with each storage system.
•Install the socket-outlet near the equipment in an easily accessible location.
•Observe the on-board battery precautions.
Risk of e xplosion if battery is replaced by an incorrect type . Dispose of used batteries
according to their instructions.
Note
•Connect the storage systems and their associated LAN connections only to equipment within the same
building.
Defaults and Technical Specifications
211
ReadyNAS OS 6 Desktop Storage Systems
Electrical Safety Precautions
Follow basic electrical safety precautions to protect yourself from harm and the ReadyNAS from damage:
•Be aware of the locations of the power on/off switch on the chassis as well as the rooms emergency
power-off s witch, disconnection s witch, or electrical outlet. If an electrical accident occurs, y ou can then
quickly remove power from the system.
•Do not work alone when working with high-voltage components.
•Always disconnect power from the system when removing or installing main system components , such
as the main board or memory modules.When disconnecting power, first power down the system with
the operating system and then unplug the power cords of all the power supply storage systems in the
system.
•When working around exposed electrical circuits, ensure that another person who is familiar with the
power-off controls is nearby to switch off the power if necessary.
•Use only one hand when working with powered-on electrical equipment.This is to avoid making a
complete circuit, which will cause electrical shock. Use extreme caution when using metal tools, which
can easily damage any electrical components or circuit boards they come into contact with.
•Do not use mats designed to decrease static electrical discharge as protection from electrical shock.
Instead, use rubber mats that have been specifically designed as electrical insulators.
•Use only power supply cords that include a grounding plug and plug them into grounded electrical
outlets.
General Safety Precautions
Follow these rules to ensure general safety:
•Keep the area around the ReadyNAS clean and free of clutter.
•See the technical specifications in this manual f or details about your specific ReadyNAS storage systems.
•Replace the on-board battery only with the same battery or an equiv alent type of battery recommended
by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
Installing the battery upside down reverses its polarities and creates a danger of
explosion.
Note
•Only trained service technicians can replace the soldered-in self-resetting PTC (positive temperature
coefficient) fuses on the main board, using only new fuses that are the same as or equivalent to the
ones being replaced. Contact technical support for details and support.
Electrostatic Discharge Precautions
Electrostatic discharge (ESD) is generated by two objects with diff erent electrical charges coming into contact
with each other . An electrical discharge is created to neutralize this diff erence, which can damage electronic
components and printed circuit boards.The following measures are generally sufficient to neutralize this
difference before contact is made to protect your equipment from ESD:
Defaults and Technical Specifications
212
ReadyNAS OS 6 Desktop Storage Systems
•Use a grounded wrist strap designed to prevent static discharge.
•Keep all components and printed circuit boards (PCBs) in their antistatic bags until ready for use.
•Touch a grounded metal object before removing the board from the antistatic bag.
•Do not let components or PCBs come into contact with your clothing, which might retain a charge even
if you are wearing a wrist strap.
•Handle a board by its edges only; do not touch its components, peripheral chips, memory modules, or
contacts.
•When handling chips or modules, avoid touching their pins.
•Put the main board and peripherals back into their antistatic bags when not in use.
•F or grounding purposes, mak e sure your computer chassis pro vides excellent conductivity between the
power supply, the case, the mounting fasteners, and the main board.
Defaults and Technical Specifications
213
ReadyNAS OS 6 Desktop Storage Systems