Table of Contents
- Contents
- Introduction
- General description
- What do the icons on my appliance handle mean?
- What does the icon on my Quick Clean Pod mean?
- How do I charge my appliance?
- How do I use my appliance and the attachments?
- How do I clean my appliance and the attachments?
- How do I use the Quick Clean Pod?
- How do I connect my shaver and smartphone?
- How do I replace the shaving heads?
- Ordering accessories
- Troubleshooting
Philips S7783/35 User Manual
Displayed below is the user manual for S7783/35 by Philips which is a product in the Men's Shavers category. This manual has pages.
Related Manuals
S7000 series
3
1
2
4
5
6
7
8 9
11 12
13 14 15
17 18 19 20 21
10
16
English
Contents
Introduction_______________________________________________________ 6
General description_______________________________________________ 6
What do the icons on my appliance handle mean?_____________ 7
What does the icon on my Quick Clean Pod mean?_____________ 9
How do I charge my appliance?__________________________________ 9
How do I use my appliance and the attachments?______________ 11
How do I clean my appliance and the attachments?____________ 20
How do I use the Quick Clean Pod?______________________________ 24
How do I connect my shaver and smartphone?_________________ 27
How do I replace the shaving heads?____________________________ 30
Ordering accessories_____________________________________________ 31
Troubleshooting__________________________________________________ 32
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that
Philips offers, register your product at
www.philips.com/welcome or via the app.
General description
1 Pop-up trimmer
2 Trimmer release slide
3 Shaving unit
4 Shaving unit release button
5 On/off button
6 Handle
7 Socket for small plug
8 Charging stand
9 Supply unit
10 Small plug
11 Protection cap
12 Pouch
13 Philips Quick Clean Pod cartridge
14 Quick Clean Pod
6English
15 Cleaning brush
16 Length settings
17 Click-on beard styler attachment
18 Comb for beard styler attachment
19 Attachment holder
20 Click-on cleansing brush attachment
21 Click-on nose trimmer attachment
Note: The accessories supplied may vary for
different products. The box shows the accessories
that have been supplied with your appliance.
What do the icons on my appliance handle
mean?
Icon Behavior Meaning
Pulsing The cleaning program is in progress.
Flashing slowly
when you
remove the
shaver from the
Quick Clean Pod
during the
cleaning program
The cleaning program was interrupted. If
you put the shaver back into the Quick
Clean Pod within four seconds, the
cleaning program resumes automatically.
Flashing when
you switch off
the appliance
Clean the shaver in the Quick Clean Pod
(see 'How do I use the Quick Clean Pod?').
Clean the attachments under the tap (see
'How do I clean my appliance and the
attachments?').
Lights up
continuously
The cleaning program is in progress.
7
English
Icon Behavior Meaning
Flashing quickly
when you
remove the
shaver from the
Quick Clean Pod
or press the
on/off button
during the
cleaning program
The cleaning program was stopped. If you
wish to continue, you need to restart the
cleaning cycle by putting the shaver into
the Quick Clean Pod and pressing the
on/off button.
Lights up The SkinIQ is actively detecting your
shaving behavior.
Lights up green The correct shaving motion (circular
movements) was used.
Lights up orange Your shaving motion can be improved.
See the app for details and advice.
Lights up Open the app. Either there is a notification
waiting for you or you need to sync your
shaves to prevent data loss (see 'How do I
connect my shaver and smartphone?').
Flashing slowly No connection is established between
your shaver and smartphone (see 'How do
I connect my shaver and smartphone?').
Flashing quickly An error has occurred (e.g. the motor is
blocked). Check the app for details.
Flashing The appliance must be disconnected from
the wall socket before you can switch it
on (see 'How do I charge my appliance?').
Flashing when
you press the
on/off button
The travel lock is activated (see 'Storage
and travel').
Lights up when
you pick up the
appliance
The number of bars lit up show the
remaining battery charge.
8English
Icon Behavior Meaning
Bottom light
flashing orange
The battery is almost empty (see 'How do
I charge my appliance?').
Lights flashing in
sequence
The appliance is charging.
Lights up
continuously
The appliance is fully charged.
What does the icon on my Quick Clean Pod
mean?
Icon Behavior Meaning
Becomes visible on the
Quick Clean Pod
The Quick Clean Pod Cartridge
needs to be replaced (see
'How do I use the Quick Clean
Pod?').
How do I charge my appliance?
Charge the appliance before you use it for the first
time and when the bottom light of the battery
status indicator flashes orange, indicating that the
battery is almost empty.
Charging takes approx. 1 hour.
Quick Charge: After approx. 5 minutes of charging,
the battery contains enough energy for one shave.
When the appliance is fully charged it has a
cordless operating time of up to 60 minutes.
Note: You cannot use the appliance while it is
charging.
Charging with the supply unit
1Make sure that the appliance is switched off.
9
English
2Insert the small plug into the appliance and put
the supply unit in the wall socket.
-While the appliance is in quick charge mode,
the lights of the battery status indicator light
up one after the other. After approximately 5
minutes, the bottom light of the battery
status indicator flashes. The battery now
contains enough energy for one shave.
-While the appliance charges, first the bottom
light of the battery status indicator flashes
and then lights up continuously. Next the
second light flashes and then lights up
continuously, and so on until the appliance
is fully charged.
-When the appliance is fully charged, all three
battery indicator lights light up continuously.
After approx. 30 minutes, the light goes out
automatically.
3After charging, remove the supply unit from the
wall socket and pull the small plug out of the
appliance.
Charging in the charging stand (specific models only)
1Make sure the appliance is switched off.
2Put the small plug in the charging stand and put
the supply unit in the wall socket.
3Place the appliance in the charging stand.
Specific models only: The light ring on the
bottom of the charging stand lights up and
rotates quickly.
-After approximately 5 minutes, the light ring
rotates slower. The battery now contains
enough energy for one shave.
10 English
-As the appliance continues to charge, the
light ring becomes brighter and rotates
slower.
-When the appliance is fully charged, the light
ring lights up fully and stops rotating.
4After charging, remove the supply unit from the
wall socket and pull the small plug out of the
charging stand.
'Unplug for use' symbol
The 'unplug for use' symbol flashes to remind you
to disconnect the appliance from the wall socket
and remove the small plug from the appliance
before you switch it on.
How do I use my appliance and the
attachments?
Warning: Always check the appliance and
all accessories before use. Do not use the
appliance or any accessory if it is damaged,
as this may cause injury. Always replace a
damaged part with one of the original type.
Note: This appliance is waterproof. It is suitable for
use in the bath or shower and for cleaning under
the tap. For safety reasons, the appliance can
therefore only be used without cord.
SkinIQ
This appliance is equipped with SkinIQ technology
which intelligently detects your hair density and
shaving technique. For a better technique, you can
get personalized shaving advice in the app.
You get advice in 2 ways: guided shaves in real
time and synchronized shaves. We advise you to
11
English
start with the guided shave to enhance your
shaving experience.
- Correct handling of your appliance will
contribute to the best shaving result.
- Follow the advice obtained from the
synchronized shaves and the personalized
programs.
Shaving
You can use this appliance either wet or dry, or
even under the shower. For a wet shave, apply
some water and shaving foam or gel to your skin
and rinse the shaving heads under the tap with
warm water before following the steps below.
1Switch on the appliance.
2Move the shaving heads over your skin in
circular movements to catch all hairs growing in
different directions. Make sure each shaving
head is fully in contact with the skin. Exert
gentle pressure for a close, comfortable shave.
Note: Do not press too hard, as this can cause
skin irritation.
Note: If you are shaving with gel or foam, rinse
the shaving unit regularly during your shave to
ensure that it continues to glide smoothly over
your skin.
12 English
3Use the narrow sides of the shaving unit to
shave in hard-to-reach areas such as along
your jawline and under your nose.
4Switch off and clean the appliance after each
use.
Note: Make sure you rinse all foam or shaving
gel off the appliance.
SkinIQ motion guidance: When you have
finished shaving you receive feedback on the
handle. The motion feedback icon lights up in
various colors, giving you feedback on your
overall shave.
-When you shave in the correct motion
(circular movements), the motion feedback
icon lights up green.
-When your shaving motion can be improved,
the motion feedback icon lights up orange.
See the app for details and advice.
Skin adaptation period
Your first shaves may not bring you the result you
expect and your skin may even become slightly
irritated. This is normal. Your skin needs time to
adapt to any new shaving system.
Follow the advice provided by the app and shave
regularly (at least 3 times a week) with this shaver
for a period of 3-4 weeks to allow your skin to
adapt to the new shaver.
Cleaning reminder
When you switch off the appliance, the cleaning
reminder flashes to remind you to clean the
appliance.
13
English
- Clean the appliance and attachments after
each use to prevent clogging and damage (see
'How do I clean my appliance and the
attachments?').
- Clean the shaving heads thoroughly once a
month or when the appliance does not shave
as well as it used to (see 'Thorough cleaning').
Synchronize your shaves
This shaver stores your shave data so you don't
need to take your smartphone with you when you
shave.
When the data storage is almost full, the
notification symbol flashes. To prevent data loss,
synchronize the shaver with the app (see 'How do I
connect my shaver and smartphone?').
1Make sure you are close to the shaver and open
the app.
2The app connects automatically and
synchronizes your last shaves.
Trimming
You can use the trimmer to groom your sideburns
and moustache.
1Push the trimmer release slide downwards to
open the trimmer.
2Switch on the appliance.
3Hold the trimmer perpendicular to the skin and
move the appliance downwards while you exert
gentle pressure.
14 English
4You can also use the trimmer under your nose.
5Switch off the appliance and clean the trimmer
after each use to prevent clogging and damage
(see 'How do I clean my appliance and the
attachments?').
6Close the trimmer.
Using the click-on attachments
Note: The accessories supplied may vary for
different products. The box shows the accessories
that have been supplied with your product.
Using the beard styler attachment with
comb
You can use the beard styler attachment with the
comb attached to style your beard at one fixed
setting or at different length settings. You can also
use it to pre-trim any long hairs before shaving for
a more comfortable shave.
The hair length settings on the beard styler
attachment correspond to the remaining hair
length after cutting and range from 1 to 5mm.
1Twist the shaving head or other attachment to
remove it from the handle and press the beard
styler attachment onto the handle.
2Slide the comb straight into the guiding grooves
on both sides of the beard styler attachment.
15
English
3Press the length selector and then push it to
the left or right to select the desired hair length
setting.
4Switch on the appliance.
5Move the appliance upwards while you exert
gentle pressure. Make sure the front of the
comb is in full contact with the skin.
6Switch off the appliance and clean the
attachment after use.
Using the beard styler attachment without
comb
You can use the beard styler attachment without
the comb to contour your beard, moustache,
sideburns or neckline to a length of 0.5mm.
You can use the beard styler attachment with the
comb attached to style your beard at one fixed
setting or at different length settings. You can also
use it to pre-trim any long hairs before shaving for
a more comfortable shave.
1Pull the comb off the beard styler attachment.
Note: Grab the comb in the center to pull it off
the beard styler attachment. Do not pull at the
sides of the comb.
2Switch on the appliance.
3Hold the beard styler attachment perpendicular
to the skin and move the appliance downwards
while you exert gentle pressure.
4Switch off the appliance and clean the
attachment after use.
16 English
Using the nose/ear trimmer attachment
You can use the nose/ear trimmer attachment to
trim your nose and/or ear hair.
Trimming nose hair
Make sure both the nose/ear trimmer attachment
and nasal passages are clean before trimming.
1Twist the shaving head or other attachment to
remove it from the handle and press the
nose/ear hair trimmer onto the handle.
2Switch on the appliance.
3Carefully insert the trimming head into one of
your nostrils.
Do not insert the attachment more than 0.5cm
into your nostrils.
4Slowly move the trimming head around inside
each nostril, making sure the side of the tip is
held firmly against the skin. This reduces the
tickling effect that can occur.
5Switch off the appliance and clean the
attachment after use.
Dried nasal mucus can block the cutting element,
preventing the appliance from switching on. If the
cutting element is blocked, clean the attachment
(see 'How do I clean my appliance and the
attachments?').
Trimming ear hair
Make sure your outer ear channels are clean and
free from wax.
1Switch on the appliance.
2Slowly move the trimming head along the rim of
the ear to remove hairs that stick out beyond
the rim.
3Carefully insert the trimming head into the
outer ear channel.
17
English
Do not insert the trimming head more than
0.5cm into your ear channel, as this could
damage the eardrum.
4Slowly turn the trimming head around to
remove all unwanted hairs from your outer ear
channel.
5Switch off the appliance and clean the
attachment after use.
Using the cleansing brush attachment
Use the cleansing brush with your daily cleansing
cream to remove oil and dirt. We advise you to use
it no more than once a week.
Caution: Do not use the appliance on damaged or
irritated skin or on wounds.
1Twist the shaving head or other attachment to
remove it from the handle and press the
cleansing brush attachment onto the handle.
2Moisten the cleansing brush with water.
Do not use the cleansing brush dry as this can
irritate the skin.
3Moisten your face with water and apply a
cleanser to your face.
4Place the cleansing brush on your cheek.
5Switch on the appliance.
20 sec.
6Gently move the brush across your skin from
the nose towards the ear. Do not press too
hard. Make sure that the treatment remains
comfortable.
Do not cleanse the sensitive area around your
eyes.
18 English
20 sec.
7After approx. 20 seconds, move the appliance
to your other cheek and start cleansing this part
of your face.
20 sec.
8After approx. 20 seconds, move the appliance
to your forehead and start cleansing this part of
your face. Gently move the brush head from left
to right.
We advise you to not overdo the cleansing and
to not cleanse any zone longer than 20
seconds.
9Switch off the appliance and clean the
attachment after use.
10 After the treatment, rinse and dry your face.
Your face is now ready for the next step of your
daily skincare routine.
Storage and travel
Note: We advise you to let the appliance and its
attachments dry before you store them for the
next use.
- Put the protection cap (if supplied) on the
shaver to protect it from dirt accumulation.
- Store the appliance in the pouch (if supplied).
- Alternatively, store the appliance on the
charging stand (if supplied) or in the Philips
Quick Clean Pod (if supplied).
Travel lock
You can lock the shaver when you are going to
travel to prevent it from switching on accidentally.
Activating the travel lock
19
English
3 sec.
Press the on/off button for 3 seconds to use the
travel lock mode.
When the travel lock is activated, the travel lock
symbol flashes.
Note: Bluetooth is switched off when the travel
lock is activated.
Deactivating the travel lock
Press the on/off button for 3 seconds.
Once the travel lock is deactivated, the appliance
switches on automatically.
Note: The shaver unlocks automatically when it is
connected to a wall socket.
How do I clean my appliance and the
attachments?
Clean the appliance and the attachments after
each use for optimal performance.
Cleaning the shaver under the tap
Clean the shaver after each use to prevent
clogging and damage.
Never dry the shaving unit with a towel or tissue,
as this may damage the shaving heads.
While rinsing the shaving unit, water may drip out
of the base of the shaver. This is a normal
occurrence.
1Switch on the shaver.
2Rinse the shaving unit under a warm tap.
20 English
3Switch off the shaver. Press the release button
to open the shaving unit.
4Rinse the hair chamber under a warm tap.
5Rinse the shaving head holder under a warm
tap.
6Carefully shake off excess water and let the
shaving head holder air-dry completely.
7Close the shaving unit.
Thorough cleaning
We advise you to clean the shaving heads
thoroughly once a month or when the shaver does
not shave as well as it used to.
1Make sure that the appliance is switched off
and disconnected from the wall socket.
21
English
2Press the release buttons on the shaving unit
and pull the shaving head holder off the
shaving unit.
3Rinse the hair chamber and shaving head
holder under the tap.
4Remove the shaving heads. For detailed
instructions, see 'How do I replace the shaving
heads?.'
Note: Do not clean more than one cutter and
guard at a time, since they are all matching sets.
If you accidentally put a cutter in the wrong
shaving guard, it may take several weeks before
optimal shaving performance is restored.
5Clean the cutter and guard under the tap.
6Shake off excess water.
7Put the shaving heads back into the shaving
unit. For detailed instructions, see 'How do I
replace the shaving heads?.'
8Insert the hinge of the shaving head holder into
the slot in the top of the shaving unit and close
the shaving unit.
Cleaning the pop-up trimmer
Clean the trimmer after each use to prevent
clogging and damage.
Never dry the trimmer teeth with a towel or
tissue, as this may damage the trimmer teeth.
22 English
1Make sure that the appliance is switched off
and disconnected from the wall socket.
2Push the trimmer release slide down to open
the pop-up trimmer.
3Switch on the appliance and rinse the pop-up
trimmer with warm water.
4After cleaning, switch off the appliance.
5Carefully shake off excess water and let the
pop-up trimmer air dry.
6Close the trimmer.
Tip: For optimal performance, lubricate the teeth
of the pop-up trimmer with a drop of mineral oil
every six months (oil not included).
Cleaning the click-on attachments
Never dry the trimmer or beard styler attachments
with a towel or tissue, as this may damage the
trimming teeth.
The accessories supplied may vary for different
products. The box shows the accessories that have
been supplied with your product.
Clean the click-on attachments after each use for
optimal performance.
1Make sure that the appliance is switched off.
2Twist the attachment to remove it from the
handle.
Pull the cleansing brush head straight off of the
attachment holder.
23
English
3Clean the parts thoroughly with warm water.
Use soap only on the cleansing brush
attachment.
Tip: If rinsing the nose/ear trimmer attachment
under the tap is not sufficient, press the
attachment onto handle and immerse the
trimming head in a glass with warm water for a
few minutes. Then switch on the appliance and
rinse it under the tap.
4Carefully shake off excess water from the beard
styler, combs and nose/ear trimmer
attachments and let them air dry completely.
Dry the cleansing brush attachment with a
towel.
Never dry the cutting unit with a towel or
tissue, as this may damage the trimming teeth.
Tip: For optimal performance, lubricate the
teeth of the beard styler attachment with a
drop of sewing machine oil regularly.
How do I use the Quick Clean Pod?
Preparing the Quick Clean Pod for use
1Twist and remove the top of the Quick Clean
Pod.
2
1
2Twist the lid off of the Quick Clean Pod
Cartridge.
24 English
3Lift the tab on the seal and pull it by the corner
to remove the seal from the Quick Clean Pod
Cartridge.
4Press the small circular piece on the handle of
the Quick Clean Pod Cartridge to break the
snap hook on the handle.
5Place the Quick Clean Pod Cartridge into the
Quick Clean Pod.
6Put the top of the Quick Clean Pod back onto
the base and turn it clockwise until you hear a
click.
Do not tilt the Quick Clean Pod to prevent
leakage.
Using the Quick Clean Pod
Note: If you use the shaver with shaving foam,
shaving gel or pre-shave products, thoroughly
rinse the shaving heads before you use the Quick
25
English
Clean Pod (see 'How do I clean my appliance and
the attachments?').
Always shake excess water off the shaver before
you place it in the Quick Clean Pod.
1Place the shaver upside down into the Quick
Clean Pod. The shaver automatically detects
that it is in the Quick Clean Pod.
2Switch on the shaver to start the cleaning
program.
Each cleaning program takes approximately
one minute. During the cleaning program the
cleaning symbol lights up continuously and the
blue icon pulses.
The shaver handle vibrates twice quickly when
the cleaning program is finished.
3Let the shaver air-dry completely in the Quick
Clean Pod before storing it.
Replacing the Quick Clean Pod Cartridge
Replace the Quick Clean Pod Cartridge
immediately when the cartridge replacement icon
on the Quick Clean Pod becomes visible or follow
the table below.
Frequency of use Cycles When to replace
the Quick Clean
Pod Cartridge
Every day About 30 Every month
A few times per week About 20 Every 2 months
Every week About 13 Every 3 months
Every month About 3 Every 3 months
26 English
1Twist and remove the top of the Quick Clean
Pod.
2Lift the Quick Clean Pod Cartridge out of the
Quick Clean Pod by the handle.
3Pour any remaining fluid down a drain and
recycle the empty cartridge in accordance with
local waste regulations.
4Place a new Quick Clean Pod Cartridge into the
Quick Clean Pod (see 'Preparing the Quick
Clean Pod for use').
Scan the QR code to the left or visit
www.philips.com/cleaning-cartridge to order
replacement Quick Clean Pod Cartridges.
How do I connect my shaver and
smartphone?
Note: Make sure your smartphone is equipped
with Bluetooth® 4.1 or higher.
This shaver is compatible with Bluetooth® 4.1 and
higher to connect to the app. When you have
paired your shaver and smartphone, Bluetooth on
your shaver is switched on automatically, even
when the shaver is switched off. This allows your
27
English
shave data to be synced later so you don't need to
take your smartphone with you when you shave.
The first few times you switch on the shaver, the
notification symbol flashes if no connection is
established with a smartphone.
3 sec.
You can switch off Bluetooth on your shaver by
activating the travel lock (see 'Storage and travel').
Pair the shaver and smartphone
You can use the app to synchronize your shave
data, change your personal settings and get
routine-based coaching.
The app is compatible with a wide range of iPhone
and Android™ smartphones.
More information is available at www.philips.com.
1Download the app.
S7920
2Make sure Bluetooth on you smartphone is
switched on.
28 English
3Switch on the shaver.
4Open the app and follow the instructions to
start the pairing process.
5Once paired, the shaver and app connect
automatically when the app is open and
Bluetooth on your phone is switched on.
Notification symbol
The shaver is equipped with a notification symbol.
The notification symbol lights up when there is an
important message for you in the app. When it
lights up, simply open the app on your smartphone
and follow the easy tips that the app gives you. If
you need further support, visit
www.philips.com/support.
Unpair the shaver and smartphone
You can pair your shaver with only one
smartphone at a time. To unpair your shaver from
your smartphone (e.g. when you get a new
smartphone), follow these steps:
Unpair the shaver: press and hold the on/off
button on the handle for approx. 10 seconds to
remove the bond between shaver and app.
Note: Unpairing is successful when the
notification symbol lights up 4 times briefly.
Unpair your smartphone:
1Go to the settings on your smartphone and
select Bluetooth.
2Tap on the name of the shaver.
3Tap 'forget' or 'unpair'.
Note: The unpairing procedure may vary by
smartphone. Please check your smartphone
manual for more information.
29
English
How do I replace the shaving heads?
For maximum shaving performance, we advise you
to replace the shaving heads every two years.
Replace damaged shaving heads immediately.
Always replace the shaving heads with original
Philips shaving heads (see 'Ordering accessories').
Replacing the shaving heads
1Switch off the shaver.
2Press the release buttons on the shaving unit
and pull the shaving head holder off the
shaving unit.
2
1
3Turn the retaining rings anticlockwise and
remove them. Place them aside in a safe place.
4Remove the shaving heads from the shaving
head holder.
Discard the used shaving heads immediately to
avoid mixing them with the new shaving heads.
5Place new shaving heads in the holder.
30 English
2
1
6Place the retaining rings back onto the shaving
heads and turn them clockwise to reattach the
retaining ring.
- Each retaining ring has two recesses that fit
exactly into the projections of the shaving head
holder. Turn the ring clockwise until your hear a
click to indicate that the ring is fixed.
Note: Hold the shaving head holder in your
hand when you reinsert the shaving heads and
reattach the retaining rings. Do not place the
shaving head holder on a surface, as this may
cause damage to the shaving heads.
7Insert the hinge of the shaving head holder into
the slot in the top of the shaving unit and close
the shaving unit.
Ordering accessories
To buy accessories or spare parts, visit
www.philips.com/parts-and-accessories or go to
your Philips dealer. You can also contact the
Philips Consumer Care Center in your country (see
the international warranty leaflet for contact
details).
The following accessories and spare parts are
available:
- SH71 replacement Philips shaving heads
31
English
- CC12 Philips Quick Clean Pod Cartridge 2-pack
- CC13 Philips Quick Clean Pod Cartridge 3-pack
- CC16 Philips Quick Clean Pod Cartridge 6-pack
Note: The availability of the accessories may differ
by country.
Troubleshooting
This chapter summarizes the most common
problems you could encounter with the appliance.
If you are unable to solve the problem with the
information below, visit www.philips.com/support
for a list of frequently asked questions or contact
the Consumer Care Center in your country.
Shaver
Problem Possible cause Solution
I cannot
connect the
shaver.
You have not
downloaded the
app.
Download the app.
Your shaver and
smartphone are
not paired yet.
Pair your shaver and
smartphone following the
instructions in the app.
The first pairing
attempt failed.
Unpair your shaver and
smartphone (see 'Unpair the
shaver and smartphone') and
try pairing them again (see
'Pair the shaver and
smartphone').
Your smartphone
cannot find your
shaver.
Make sure your smartphone is
equipped with Bluetooth 4.1
or higher.
Make sure Bluetooth is
activated on your shaver and
smartphone.
32 English
Problem Possible cause Solution
Make sure that your
smartphone is within
onemeter of your shaver to
enable a Bluetooth
connection.
Make sure your shaver is
charged.
I want to use
the shaver
without the
app.
You do not have to connect
your shaver with your
smartphone before each
shave. To get personalized
shaving tips, just make sure
that you connect it at least
once every 20 shaves to
synchronize your shave data.
The appliance
does not work
when I press
the on/off
button.
The appliance is
still attached to the
wall socket. For
safety reasons, the
appliance can only
be used without
cord.
Unplug the appliance and
press the on/off button to
switch on the appliance.
The rechargeable
battery is empty.
Recharge the battery.
The travel lock is
activated.
Press the on/off button for 3
seconds to deactivate the
travel lock.
The shaving unit is
soiled or damaged
to such an extent
that the motor
cannot run.
Clean the shaving heads
thoroughly or replace them.
Theappliance
does not shave
as well as it
used to.
The shaving heads
are damaged or
worn.
Replace the shaving heads.
33
English
Problem Possible cause Solution
Hairs or dirt
obstruct the
shaving heads.
Clean the shaving heads
thoroughly.
Water is
leaking from
the bottom of
the appliance.
During cleaning,
water may collect
between the inner
body and the outer
shell of the
appliance.
This is normal and not
dangerous because all
electronics are enclosed in a
sealed power unit inside the
appliance.
Philips Quick Clean Pod
Problem Possible cause Solution
My shaver isn't clean
after using the Philips
Quick Clean Pod.
You removed the
shaver before the
cleaning program
was finished.
Leave the shaver in
the Philips Quick
Clean Pod for the full
cleaning program.
Each cleaning
program takes
approximately 1
minute. The cleaning
icon goes out when
the cleaning program
is finished.
The Philips Quick
Clean Pod Cartridge
needs to be replaced.
Replace the Philips
Quick Clean Pod
Cartridge.
The Philips Quick
Clean Pod is tilted.
Place the Philips
Quick Clean Pod on a
flat surface.
My Philips Quick
Clean Pod does not
switch on.
The Philips Quick
Clean Pod is
powered by the
motor of the shaver.
Place the shaver into
the Philips Quick
Clean Pod. Switch on
the shaver.
The shaver is
connected to the wall
socket.
Disconnect the
shaver from the
supply unit.
34 English
The shaver battery is
empty.
Charge the shaver
before using the
Philips Quick Clean
Pod.
My Philips Quick
Clean Pod is
overflowing.
You regularly use the
Philips Quick Clean
Pod after rinsing the
shaver but not
shaking off excess
water.
Shake off excess
water after rinsing
the shaving heads
each time before
putting the shaver
into the Philips Quick
Clean Pod.
You shaved with
shaving gel or foam
and did not rinse the
shaver before using
the Philips Quick
Clean Pod.
Rinse the shaving
heads thoroughly
before using the
Philips Quick Clean
Pod (see 'Using the
Quick Clean Pod').
35
English
© 2020 Koninklijke Philips N.V.
All rights reserved
3000.057.1983.1 (14/8/2020)
>75 % recycled paper
>75 % papier recyclé