Philips TPV SN 503 BK User Manual
Displayed below is the user manual for TPV SN 503 BK by Philips which is a product in the Headphones & Headsets category. This manual has pages.
Related Manuals
User manual
Register your product and get support at
www.philips.com/support
5000 Series
Sports
SN503
1 Important safety instructions 2
Hearing Safety 2
General information 2
2 Your Bluetooth in-ear
headphones 3
What's in the box 3
Other devices 3
Overview of your Bluetooth
wireless headset 3
3 Get started 5
Charge the battery 5
Pair the headphones with your
mobile phone 5
4 Use your headphones 6
Connect the headphones to a
Bluetooth device 6
Manage your calls and music 6
5 Technical data 8
6 Notice 9
Declaration of conformity 9
Disposal of your old product
and battery 9
Compliance with EMF 9
Environmental information 9
Notice of compliance 10
7 Frequently asked questions 11
Contents
1 Important
safety
instructions
Hearing Safety
Danger
To avoid hearing damage, limit the time you
use headphones at high volume and set the
volume to a safe level. The louder the
volume, the shorter the safe listening time is.
Be sure to observe the following guide-
lines when using your headset.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume
continuously upwards as your
hearing adapts.
• Do not turn up the volume so high
that you can't hear what's around
you.
• You should use caution or tempo-
rarily discontinue use in potentially
hazardous situations.
• Excessive sound pressure from
earphones and headphones can
cause hearing loss.
• Using headphones with both ears
covered while driving is not recom-
mended and may be illegal in some
areas while driving.
• For your safety, avoid distractions
from music or phone calls while in
environments.
General information
To avoid damage or malfunction:
Caution
Do not expose headphones to excessive heat
Do not drop your headphones.
Headphones shall not be exposed to dripping
or splashing.
Do not allow your headphones to be
submerged in water.
Do not use any cleaning agents containing
alcohol, ammonia, benzene, or abrasives.
If cleaning is required use a soft doth, if
necessary dampened with a minimum amount
of water or diluted mild soap, to clean the
product.
The integrated battery shall not be exposed to
excessive heat such as sunshine, re or the
like.
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type.
About operating and storage
temperatures and humidity
• Battery life may be shorter in high
or low temperature conditions.
Operate in a place where
temperature is between 0ºC
(32ºF) and 45ºC(113ºF) (up to
90% relative humidity).
store in a place where
temperature is between -25ºC
(-13ºF) and 55ºC(131ºF) (up to
50% relative humidity).
2 Your
Bluetooth
in-ear
headphones
What's in the box
Philips Bluetooth in-ear headphones
Philips SN503
Replaceable rubber ear caps x 2 pairs
Quick start guide
Other devices
A mobile phone or device (e.g. note-
book, PDA, Bluetooth adapters, MP3
players etc) which supports Bluetooth
and is compatible to the headset (see
'Technical data' on page 8).
Congratulations on your purchase, and
welcome to Philips! To fully benet
from the support that Philips oers,
register your product at
www.philips.com/welcome.
With this Philips in-ear headphones,
you can:
• enjoy convenient wireless
handsfree calls;
• enjoy and control wireless music;
• switch between calls and music.
USB charging cable (for charging only)
L
S
Overview of your
Bluetooth wireless
headset
- Volume control button
Multi-function buttons
+ Volume control button
Heart rate button
LED indicator
Micro USB charging slot
Microphone
3 Get started
Charge the battery
Note
charge the battery for 3 hours for optimum
battery capacity and lifetime.
Use only the original USB charging cable to
avoid any damage.
Finish your call before charging the headset,
as connecting the headset for charging will
Connect the supplied USB charging
cable to:
• The micro USB charging slot on the
headphones and;
• The charger/USB port of a
computer.
Tip
Normally, a full charge takes 2 hours.
Pair the headphones
with your mobile phone
Make sure that the headphones are
Before you use the headphones with
it with a mobile phone. A successful
pairing establishes a unique encrypted
link between the headphones and
mobile phone. The headphones store
the last 8 devices in the memory. If you
try to pair more than 8 devices, the
earliest paired device is replaced by the
new one.
LED turns white during charging and
turns o when the headphones in
fully charged.
Press and hold for 6 seconds
until the blue and white LED
ashes alternately.
Philips SN503
4 Use your
headset
Connect the headset to
your Bluetooth device
Turn on your mobile phone/
Bluetooth device.
turn the headphones on.
The headphones are recon-
nected to the last connected
mobile phone/ Bluetooth
device automatically. If the last
one is not available, the
headphones try to reconnect to
the second last connected
device.
Tip
If you turn on the mobile phone/Bluetooth
device or activate the Bluetooth feature
after turning on the headphones, you have
to reconnect the headphones and mobile
phone/Bluetooth device manually.
If the headphones fail to connect to any
Bluetooth device within range in 5 minutes,
battery life.
Note
Manage your calls and
music
Task Button Operation
Turn the
head-
phones on.
Press and hold
for 2 seconds.
Turn the
head-
Press and hold
for 3 seconds.
The white
LED is
on and
fades
out.
Music control
Task Button Operation
Play or
pause music.
Press once.
Press once.
Long press.
Long press.
Adjust volume.
Next track.
Previous track.
Call control
Task Button Operation
Pick up/
hang up a
call.
Switch
caller
during a
call.
Press once.
Press twice.
1 beep.
1 beep.
Other headphones indicator status
Headphones status Indicator
The headphones
are connected
to a Bluetooth
device, while the
headphones in
standby mode
or while you are
listening to music.
The blue LED
ashes for every
10 seconds.
5 seconds.
The headphones
are ready for
pairing.
blue and white
The LED ashes
alternately.
The headphones
are on but not
connected to a
Bluetooth device.
The blue LED
If no connection
can be made, the
headphones will
turn itself o within
5 minutes.
Low battery level. The white LED
ashes 3 times for
every 60 seconds
until it is out of
All LED is o.
power
Battery is fully
charged.
5 Technical data
Note
notice.
Headset
Music time: 6 hours
Talk time: 8 hours
Standby time: 160 hours
Charging time: 2 hours
Rechargeable lithium polymer
battery (120 mAh)
Bluetooth version: 5.0
• A2DP (Advanced Audio Distri-
• AVRCP (Audio Video Remote
Supported audio codec: SBC AAC
Frequency range: 2.402-2.480 GHz
Transmitter power: < 10 dBm (Only for EU)
Operating range: Up to 10 meters (33
feet)
Digital echo & noise reduction
Remove the integrated battery
6 Notice
Hereby, MMD Hong Kong Holding Limited
declares that this product is in compli-
ance with the essential requirements and
other relevant provisions of Directive
of Conformity on www.p4c.philips.com.
Declaration of conformity
Disposal of your old
product and battery
Your product is designed and manufac-
tured with high quality materials and
components, which can be recycled and
reused.
This symbol on a product means that
the product is covered by European
Directive 2012/19/EU.
This symbol means that the product
contains a built-in rechargeable battery
covered by European Directive
2013/56/EU which cannot be disposed
of with normal household waste. We
strongly advise you to take your product
service centre to have a professional
remove the rechargeable battery.
Inform yourself about the local separate
collection system for electrical and
electronic products and rechargeable
batteries. Follow local rules and never
dispose of the product and rechargeable
batteries with normal household waste.
Correct disposal of old products and
rechargeable batteries helps prevent
negative consequences for the environ-
ment and human health.
If there is no collection/recycling system
for electronic products in your country,
you can protect the environment by
removing and recycling the battery
before disposing the headphones.
• Make sure the headset is discon-
nected from the charging case
before removing the battery.
Compliance with EMF
Environmental information
This product complies with all applica-
ble standards and regulations regarding
All unnecessary packaging has been
omitted. We have tried to make the
packaging easy to separate into three
materials: cardboard (box), polystyrene
protective foam sheet.)
Your system consists of materials which
can be recycled and reused if disassem-
bled by a specialized company. Please
observe the local regulations regarding
the disposal of packaging materials,
exhausted batteries and old equipment.
Notice of compliance
The device complies with the FCC rules,
Part 15. Operation is subject to the
following two conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any
interference received, including
interference that may cause
undesired operation.
FCC rules
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to part
15 of the FCC Rules. These limits are
designed to provide reasonable protec-
tion against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed
and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or
television reception, which can be
and on, the user is encouraged to try to
correct the interference by one or more
of the following measures:
Relocate the receiving antenna.
Increase the separation between
equipment and receiver
Connect the equipment into an outlet
the receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC
radiation exposure limits set forth for an
uncontrolled environment.
This transmitter must not be co-located
or operating in conjunction with any
other antenna or transmitter.
Canada:
This device contains licence-exempt
transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the follow-
ing two conditions:
1. This device may not cause interference.
2. This device must accept any interfer-
ence, including interference that may
cause undesired operation of the device.
L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences
et Développement économique Canada
applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux
deux conditions suivantes:
1. L’appareil ne doit pas produire de
brouillage;
2. L’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le
fonctionnement.
CAN ICES-3 (B)/NMB-3(B)
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102
radiation exposure limits set forth for an
uncontrolled environment. This transmitter
must not be co-located or operating in
conjunction with any other antenna or
transmitter.
ce matériel est conforme aux limites de
dose d'exposition aux rayonnements ic
rss-102 énoncées pour un autre
environnement.cet émetteur ne doit pas
être situées ou opérant conjointement
avec toute autre antenne ou l'émetteur.
Caution:
The user is cautioned that
changes or modications not expressly
approved by the party responsible for
compliance could void the user’s
autrhority to operate the equipment.
7 Frequently
asked
questions
My Bluetooth headset does not turn on.
The battery level is low. Charge the
headset.
I cannot pair my Bluetooth headset with
my Bluetooth device.
The Bluetooth is disabled. Enable the
Bluetooth feature on your Bluetooth
device and turn on the Bluetooth device
before you turn on the headset.
Pairing does not work.
• Make sure the headset are in pairing
mode.
• Follow the steps described in this user
manual (see “Pair the headset with your
mobile phone” on page 5 ).
• Make sure that the LED light ashes blue
and white alternately.
How to reset pairing.
headset.
• The headset may be connected to a
connected device or move it out of
previously paired device. Turn o the
range.
• Pairing may have been reset or the
headset has been previously paired
with another device. Pair the headset
with the Bluetoot device again as
described in the user manual. (see
‘Pair the headset with your Bluetooth
device at the rs time’ on page 8).
My Bluetooth headset is connected to a
Bluetooth stereo enabled mobile phone,
but music only plays on the mobile phone
speaker.
Refer to the user manual of your mobile
phone. Select to listen to music through
the headset.
The audio quality is poor and crackling
noise can be heard.
• The Bluetooth device is out of range.
Reduce the distance between your
headset and Bluetooth device, or
remove obstacles between them.
• Charge your headset.
The audio quality is poor when streaming
from the mobile phone is very slow, or
audio streaming does not work at all.
Make sure your mobile phone not only
supports (mono) HSP/HFP but alos
supports A2DP and is BT4.0x (or higher)
compatible (see ‘Technical data’ on page
8).
In Power OFF state, Press & Hold MFB
button until the LED indicator turns blue
and white ashes alternately .You will
hear “Connected” , as pairing successful.
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips N.V. and are used under license. This product has been
manufactured by and is sold under the responsibility of MMD Hong Kong
Limited is the warrantor in relation to this product.
UM_TASN503_00_EN_V1.0