Philips TPV UN 102 BK User Manual
Displayed below is the user manual for TPV UN 102 BK by Philips which is a product in the Headphones & Headsets category. This manual has pages.
Related Manuals
TAUN102
User manual
Register your product and get support at
www.philips.com/support
1 Important safety instructions 2
Hearing Safety 2
General information 2
2 Your Bluetooth in-ear headphones 3
What's in the box 3
Other devices 3
Overview of your Bluetooth in-ear
3 senohpdaeh
3 Get started 4
Charge your headphones 4
Pair the headphones with your mobile
4 enohp
4 Use your headphones 5
Connect the headphones to a
Bluetooth device 5
Manage your calls and music 5
5 Technical data 7
6 Notice 8
Notice of compliance 8
Disposal of your old product and battery 8
9 skramedarT
7 Frequently asked questions 10
Contents
EN 1
2 EN
1 Important safety
instructions
Hearing Safety
Danger
To avoid hearing damage, limit the time you use
headphones at high volume and set the volume to a
safe level. The louder the volume, the shorter the safe
listening time is.
Be sure to observe the following guidelines
when using your headset.
• Listen at reasonable volumes for reason-
able periods of time.
• Be careful not to adjust the volume
continuously upwards as your hearing
adapts.
• Do not turn up the volume so high that
you can't hear what's around you.
• You should use caution or temporarily
discontinue use in potentially hazardous
situations.
• Excessive sound pressure from earphones
and headphones can cause hearing loss.
• Using headphones with both ears covered
while driving is not recommended and
may be illegal in some areas while driving.
• For your safety, avoid distractions from
music or phone calls while in traffic or
other potentially dangerous environments.
General information
To avoid damage or malfunction:
Caution
Do not expose headphones to excessive heat
Do not drop your headphones.
Headphones shall not be exposed to dripping or
splashing.
Do not allow your headphones to be submerged in
water.
Do not use any cleaning agents containing alcohol,
ammonia, benzene, or abrasives.
If cleaning is required use a soft doth, if necessary
dampened with a minimum amount of water or
diluted mild soap, to clean the product.
The integrated battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
About operating and storage temperatures and
humidity
• Operate or store in a place where
temperature is between -15°C (5°F) and
55°C (131 °F) (up to 90% relative
humidity.
• Battery life may be shorter in high or low
temperature conditions.
2 Your Bluetooth
in-ear
headphones
Congratulations on your purchase, and
welcome to Philips! To fully benefit from the
support that Philips offers, register your product
at www.philips.com/welcome.
With this Philips wireless in-ear headphones,
you can:
enjoy convenient wireless handsfree calls;
enjoy and control wireless music;
switch between calls and music.
What's in the box
Philips Bluetooth in-ear headphones TAUN102
Other devices
A mobile phone or device (e.g. notebook, PDA,
Bluetooth adapters, MP3 players etc) which
supports Bluetooth and is compatible to the
headphones (see 'Technical data' on page 7).
Overview of your Bluetooth
in-ear headphones
EN 3
Next / Volume up
MIC / LED indicator
On/off, music/call control button
Micro USB charging slot
Previous/Volume down
(for charging only)
Quick start guide
Earfins Caps( M / L)
USB charging cable
UN102
3 Get started
Charge your headphones
Note
Before you use your headphones for the first time,
charge the battery for 5 hours for optimum battery
capacity and lifetime.
Use only the original USB charging cable to avoid any
damage.
Finish your call before charging the headphones, as
connecting the headphones for charging will power
the headphones off.
Connect the supplied USB charging cable to:
the micro USB charging slot on the
headphones and;
the charger/USB port of a computer
LED turns red during charging and
turns blue when the headphones is fully
charged.
Tip
Normally, a full charge takes 2 hours.
Pair the headphones with
your mobile phone
Before you use the headphones with your
mobile phone for the first time, pair it with a
mobile phone. A successful pairing establishes a
unique encrypted link between the headphones
and mobile phone. The headphones store the
last 8 devices in the memory . If you try to pair
more than 8 devices , the earliest pained
device is replaced by the new one.
4 EN
Make sure that the headphones are fully
charged and turned off.
Press and hold the on/off button, blue and
red LED flashes alternately.
Blue light flashes for successful pairing.
The headphones remain in pairing
mode for 5 minutes.
Make sure that the mobile phone is turned
on and its Bluetooth feature is activated.
Pair the headphones with the mobile
phone. For detailed information, refer to
the user manual of your mobile phone.
The following example shows you how to pair
the headphones with your mobile phone.
Activate the Bluetooth feature of your
mobile phone, select Philips UN102.
Enter the headset password "0000" (4
zeros) if prompted. For those mobile
phones featuring Bluetooth 3.0 or higher,
no need to enter a password.
4 Use your
headphones
Turn on your mobile phone/Bluetooth
device.
Press and hold the on/off button to turn
the headphones on.
The blue LED flashes.
The headphones are reconnected to
the last connected mobile phone/
Bluetooth device automatically. If the
last one is not available, the
headphones try to reconnect to the
second last connected device.
Tip
If you turn on the mobile phone/Bluetooth device or
activate the Bluetooth feature after turning on the
headphones, you have to reconnect the headphones
and mobile phone/Bluetooth device manually.
If the headphones fail to connect to any Bluetooth
device within range in 5 minutes, it will switch off
automatically to save the battery life.
Note
Connect the headphones to a
Bluetooth device
Manage your calls and music
On/off
Task Button Operation
Turn the
headphones
on.
On/off,
music/call
control
Press and hold for 1
seconds.
Turn the
headphones
off.
On/off,
music/call
control
Press and hold for 3
seconds.
The red
LED is on
and fades
out.
Music control
Task Button Operation
On/off,
music/call
control
Play or pause
music.
Press once.
Press once.
Long press.
Long press.
Adjust volume.
Call control
Task Button Operation
Pick up/hang
up a call.
Switch caller
during a call.
On/off, music/
call control
On/off,
music/call
control
Press once.
1 beep.
Other headphones indicator status
Headphones status Indicator
The headphones
are connected
to a Bluetooth
device, while the
headphones in
standby mode
or while you are
listening to music.
The blue LED flashes
for every 10 seconds.
The headphones are
ready for pairing.
The LED flashes blue.
The headphones are
on but not connected
to a Bluetooth device.
The red LED flashes
If no connection
can be made, the
headphones will turn
itself off within 5
minutes.
EN 5
for every 3 seconds
Press and hold
for 1seconds.
1 beep.
Next track.
Previous track.
Low battery level. The red LED flashes
2 times for every 3
seconds until it is out
of power
Battery is fully
charged.
Red LED is off, and
blue LED is on.
6 EN
5 Technical data
Music time: 7 hours
Talk time: 6 hours
Standby time: 150 hours
Normal time for a full charge: 2 hours
Rechargeable lithium polymer battery (80
mAh)
Bluetooth 5.0 Bluetooth mono support
(Headset Profile - HSP, Hands-Free
Profile - HFP), Bluetooth stereo supported
(Advanced Audio Distribution Profile
- A2DP; Audio Video Remote Control
Profile-AVRCP)
Operating range: Up to 10 meters (33
feet)
Digital echo & noise reduction
Auto power off
Note
Specifications are subject to change without notice.
EN 7
6 Notice
Notice of compliance
The device complies with the FCC rules, Part
15. Operation is subject to the following two
conditions:
Notice for US
This device may not cause harmful
interference, and
This device must accept any interference
received, including interference that may
cause undesired operation.
FCC rules
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy
and, if not installed and used in accordance with
the instruction manual, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more
of the following measures:
Relocate the receiving antenna.
Increase the separation between
equipment and receiver
Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
FCC Radiation Exposure Statement:
environment. This transmitter must not be
co-located or operating in conjunction with any
other antenna or transmitter
CAN ICES-3(B)/NMB-3(B)
Notice for Canada:
Hereby, MMD Hong Kong Holding Limited
declares that this product is in compliance with
the essential requirements and other relevant
provisions of Directive 2014/53/EU. You can find
the Declaration of Conformity on
www.p4c.philips.com.
Declaration of conformity
8 EN
Caution: The user is cautioned that changes or
modifications not expressly approved by the
party responsible for compliance could void the
user's authority to operate the equipment.
This device contains licence-exempt transmit-
ter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to
the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference,
including interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est conforme
aux CNR d’Innovation, Sciences et Développe-
ment économique Canada applicables aux
appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionne-
ment.
Do not incinerate. Batteries may explode if
overheated.
For disposal or recycling information,
please contact your local authorities or visit
www.recycle.philips.com.
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
This symbol means that the product contains
a built-in rechargeable battery covered by
European Directive 2013/56/EU which cannot
be disposed of with normal household waste.
We strongly advise you to take your product to
an official collection point or a Philips service
centre to have a professional remove the
rechargeable battery.
Inform yourself about the local separate
collection system for electrical and electronic
products and rechargeable batteries. Follow
local rules and never dispose of the product
and rechargeable batteries with normal
household waste. Correct disposal of old
products and rechargeable batteries helps
prevent negative consequences for the
environment and human health.
Remove the integrated battery
Note
Make sure the headphones are disconnected from the
USB charging cable before removing the battery.
If there is no collection/recycling system for
electronic products in your country, you can
protect the environment by removing and
recycling the battery before disposing the
headphones.
Compliance with EMF
This product complies with all applicable
standards and regulations regarding exposure to
electromagnetic fields.
Environmental information
All unnecessary packaging has been omitted. We
have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can be
recycled and reused if disassembled by a
specialized company. Please observe the local
regulations regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
Trademarks
Bluetooth
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by MMD
Hong Kong Holding Limited is under license. Other
trademarks and trade names are those of their
respective owners.
EN 9
Disposal of your old product
and battery
This product may contain lead and mercury.
Disposal of these materials may be regulated
due to environmental considerations. For
disposal or recycling information, please contact
your local authorities or visit www.recycle.
philips.com.
This product contains non-removable batteries:
7 Frequently asked
questions
My Bluetooth headphones do not switch on.
The battery level is low. Charge the
headphones.
I cannot pair my Bluetooth headphones with a
mobile phone.
The Bluetooth is disabled. Enable the Bluetooth
feature on your mobile phone and turn on the
mobile phone before you turn on the
headphones.
Pairing does not work.
Make sure the headphones are in pairing mode.
Follow the steps described in this user
manual.
Make sure that the LED light flashes blue
and red alternately before you release
the call/music button. Do not stop holding
the button if you see the blue LED only.
The mobile phone cannot find the headphones.
The headphones may be connected to a
previously paired device. Turn off the
connected device or move it out of range.
Pairing may have been reset or the
headphones have been previously paired
with another device. Pair the headphones
with the mobile phone again as described
in the user manual.
My Bluetooth headphones are connected to a
Bluetooth stereo enabled mobile phone, but
music only plays on the mobile phone speaker.
Refer to the user manual of your mobile phone.
Select to listen to music through the
headphones.
The audio quality is poor and crackling noise
can be heard.
The Bluetooth device is out of range. Reduce
the distance between your headphones and
Bluetooth device, or remove obstacles between
them.
The audio quality is poor when streaming from
the mobile phone is very slow, or audio
streaming does not work at all.
Make sure your mobile phone not only
supports (mono) HSP/HFP but also supports
A2DP (see 'Technical data' on page 7).
I hear but cannot control music on my
Bluetooth device (e.g. play/pause/skip forward/
backward).
Make sure the Bluetooth audio source supports
AVRCP (see 'Technical data' on page 7).
For further support, visit www.philips.com/
support.
10 EN
Philips and the Philips Shield Emblem are registered
trademarks of Koninklijke Philips N.V. and are used under
license.
This product has been manufactured by and is sold
under the responsibility of MMD Hong Kong Holding
Limited or one of its affiliates, and MMD Hong Kong
Holding Limited is the warrantor in relation to this
product.
UM_TAUN102_10_EN_v2.0
Este equipamento não tem direito à proteção contra interferência prejudicial e não
pode causar interferência em sistemas devidamente autorizados.
Este produto está homologado pela ANATEL, de acordo com os procedimentos
regulamentados pela Resolução 242/2000, e atende aos requisitos técnicas
aplicados. Para maiores informações, consulte a site da ANATEL:
www.anatel.gov.br