Philips TPV ST 702 BK User Manual
Displayed below is the user manual for TPV ST 702 BK by Philips which is a product in the Headphones & Headsets category. This manual has pages.
Related Manuals
User manual
Register your product and get support at
www.philips.com/support
7000 Series
Sports
ST702
1 Important safety instructions 2
Hearing Safety 2
General information 2
2 Your Bluetooth wireless
earpieces 3
What's in the box 3
Other devices 3
Overview of your Bluetooth
wireless earpieces 4
3 Get started 5
Charge the battery 5
Pair the earpieces with your
Bluetooth device at the rst
time 6
Pair the earpieces with another
Bluetooth device 6
4 Use your headphones 7
Reconnect the earpieces to your
Bluetooth device 7
Power on/o 7
Manage your calls and music 7
LED indicator status 8
How to wear 8
5 Factory reset the earpieces 9
6 Technical data 10
7 Notice 11
Declaration of conformity 11
Disposal of your old product
and battery 11
Compliance with EMF 12
Environmental information 12
Notice of compliance 12
7 Frequently asked questions 13
Contents
1 Important
safety
instructions
Hearing Safety
Danger
To avoid hearing damage, limit the time you
use headphones at high volume and set the
volume to a safe level. The louder the
volume, the shorter the safe listening time is.
Be sure to observe the following guide-
lines when using your earpieces.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume
continuously upwards as your
hearing adapts.
• Do not turn up the volume so high
that you can't hear what's around
you.
• You should use caution or tempo-
rarily discontinue use in potentially
hazardous situations.
• Excessive sound pressure from
earphones and headphones can
cause hearing loss.
• Using headphones with both ears
covered while driving is not recom-
mended and may be illegal in some
areas while driving.
• For your safety, avoid distractions
from music or phone calls while in
trac or other potentially dangerous
environments.
General information
To avoid damage or malfunction:
Caution
Do not expose headphones to excessive heat
Do not drop your headphones.
Headphones shall not be exposed to dripping
or splashing.
Do not allow your headphones to be
submerged in water.
Do not use any cleaning agents containing
alcohol, ammonia, benzene, or abrasives.
If cleaning is required use a soft doth, if
necessary dampened with a minimum amount
of water or diluted mild soap, to clean the
product.
The integrated battery shall not be exposed to
excessive heat such as sunshine, re or the
like.
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type.
About operating and storage
temperatures and humidity
• Operate or store in a place where
temperature is between -10°C
(14°F) and 50°C (122 °F) (up to 90%
relative humidity.
• Battery life may be shorter in high
or low temperature conditions.
2 Your
Bluetooth
wireless
earpieces
What's in the box
Philips True Wireless earpiec-
es Philips ST702
Replaceable rubber ear caps x 2 pairs
Charging case
Quick start guide
Other devices
A mobile phone or device (e.g. note-
book, PDA, Bluetooth adapters, MP3
players etc) which supports Bluetooth
and is compatible to the earpieces
(see 'Technical data' on page 10).
Congratulations on your purchase, and
welcome to Philips! To fully benet
from the support that Philips oers,
register your product at
www.philips.com/welcome.
With this Philips wireless earpieces, you
can:
• enjoy convenient wireless
handsfree calls;
• enjoy and control wireless music;
• switch between calls and music.
USB charging cable (for charging only)
Overview of your
Bluetooth wireless
earpieces
Ear Cap
Microphone
Multi-function Button
LED indicator (charging case)
Micro USB charging slot
3 Get started
Charge the battery
Charging case
Earpieces
Note
Before you use your earpieces for the rst
time, place the earpiecess in the charging
case and charge the battery for 3 hours for
optimum battery capacity and lifetime.
Use only the original USB charging cable to
avoid any damage.
Finish your call before charging the earpieces,
as connecting the earpieces for charging will
power the earpieces o.
Connect one end of the USB cable into
the charging case, and another end into
the power source.
• Charging process is veried by the
blue LED light next to the USB
socket on the case.
• When the charging case is fully
charged, the blue light goes on.
• Charging process is veried by white
LED light on the earpiecess.
• When the earpieces is fully charged,
the white light goes o.
Tip
Tip
The charging case serves as a portable backup
battery for charging the earpieces. When the
charging case is fully charged, it supports 3 full
recharge cycle for the earpieces.
Normally, a full charge takes 2 hours (for the
earpieces or charging case).
Pair the earpieces with
your Bluetooth device at
the st time
Place the earpieces in the charging case.
The earpieces start charging.
The LED on both earpiecess ashes
in blue for 3 times, and then it
ashes in white.
Both earpiecess are now power on
and are paired with each other.
The charging case starts charging. Auto Power on: Open the charging
capsule, the earpiecess discharged
and the blue LED indicator ash
with “power on” voice prompt.
Manual Power on: On both earpiecess
press and hold the multi-function
buttons for approxinmately 2 seconds.
02
1 second
Note
Note
After powering on, if the earpieces cannot nd
any previously connected Bluetooth device, it
will automatically switch to pairing mode.
The earpieces stores 1 device in the memory. If
you try to pair more than 2 devices, the earliest
paired device is replaced by the new one.
Pair the earpieces with
another Bluetooth device
The earpiecess are now in
pairing mode and is ready to
pair with a Bluetooth device
(e.g. a mobile phone)
Turn on the Bluetooth function
of your Bluetooth device, select
Philips ST702.
Enter the earpieces password
“0000” (4 zeros) if prompted.
For those Bluetooth devices
featuring Bluetooth 3.0 or higher,
no need to enter a password.
Turn on the Bluetooth function of
your Bluetooth device.
Pair the earpiecess with your
Bluetooth device. Refer to the user
manual of your Bluetooth device.
The following example shows you
how to pair the earpieces with
your Bluetooth device.
If you have another Bluetooth device
that you want to pair with the earpieces,
make sure the Bluetooth function in any
other previously paired or coonected
devices are turned o. Then follow the
steps in ‘Pair the earpieces with your
Bluetooth device at the rst time’.
Philips ST702
UV sterilization function
20
UV sterilization
Put the earpieces into the charging case
and close the charging case, the white
LED on 20 seconds for earpieces UV
sterilization function.
Tip
Note
The earpieces cannot connect to more than 1
device at the same time. If you have two paired
Bluetooth devices, only turn on the Bluetooth
function of the device that you want to connect.
If you turn on the Bluetooth function of your
Bluetooth device after turning on the earpieces,
you have to go to the Bluetooth menu of the
device and connect the earpieces to the device
manully.
If the earpieces fails to connect to any
Bluetooth device within 3 minutes, it will turn o
automatically to save the battery life.
In some Bluetooth devices, connection may not
be automatic. In this case, you have to go to the
Bluetooth menu of your device and connect the
earpieces to the Bluetooth device manually.
If no device is connected, the
earpieces will automatically
turn o after 3 mins.
Both earpiecess are now
powered on and are paired
with each other automatically.
The earpieces will search the
last connected Bluetooth device
and reconnect to it automatical-
ly. If the last connected one is
not available, the earpieces will
search and reconnect to the
second last connected device.
4 Use your
earpieces
Turn on the Bluetooth function of
your Bluetooth device.
Task
Music control
Turn the
earpieces
on.
Right/Left
earpieces
Right/Left
earpieces
Press and
hold for 2
seconds.
Place both
earpiecess
in charging
case.
Press and
hold for 4
seconds.
The
white
LED
ashes
3 times.
Turn the
earpieces
o.
Play or
pause music
Skip forward Right
earpieces
Press and
hold for 2
seconds
Skip
backward
Left
earpieces
Press and
hold for 2
seconds
Right/Left
earpieces
Press twice
Take both earpiecess from the
charging case, the earpieces will
power on and reconnect automati-
cally.
Connect the earpieces to
your Bluetooth device
Power on/o
Manage your calls and
music
Multi-
function
button
Operation
Task Multi-
function
button
Operation
LED indicator status
Battery LED indicator on
Bluetooth device
How to wear
Call control
Pick up/hang
up call
Reject an
incomging
call
Right/Left
earpieces
Press and
hold for 2
seconds
Right/Left
earpieces
Press three
times
Siri/Google
The earpieces is
connected to a
Bluetooth device.
The earpieces is
powered on.
The earpieces is
pairing mode.
The earpieces is
on but not
connected to a
Bluetooth device.
The blue LED will
ashes. If no
connection can be
made, the
earpieces will turn
itself o within 15
minutes.
The white LED
ashes 3 times.
The blue LED
ashes.
Low battery level
(earpieces).
Low battery level
(charging case).
Battery is fully
charged (earpiec-
es).
The white LED
light on the
earpieces is o.
Battery is fully
charged (charging
case).
The white LED
light on the
charging case is
o.
You will hear
‘battery low’ on
the earpieces.
The blue LED on
the charging case
ashes every 1
second.
The blue LED light
ashes for every 5
seconds.
Right/Left
earpieces
Press twice
Task Multi-
function
button
Operation
Voice control
Task
Earpieces status Indicator
Multi-
function
button
Operation
It will show a battery indicator on
Bluetooth device after connected to
earpieces.
5 Factory reset
the earpieces
6 Technical data
Note
Specications are subject to change without
notice.
Earpieces
Music time: 6 hours (additional 6 hrs
with charging case)
Talk time: 6 hours (additional 6 hrs
with charging case)
Standby time: 200 hours
Charging time: 2 hours
Rechargeable lithium ion battery:
105 mAh on each earpieces
Bluetooth version: 5.0
Compatible Bluetooth proles:
• HSP (Hands-Free Prole-HFP)
• A2DP (Advanced Audio Distri-
bution Prole)
• AVRCP (Audio Video Remote
Control Prole)
Supported audio codec: SBC
Frequency range: 2.402 -2.480GHz
Transmitter power: < 1 dBm
Operating range: Up to 10 meters (33
feet)
Charging case
Charging time: 2 hrs
Rechargeable Li-ion battery: 450mAh
In Power o status, press and hold
the multi-function button of the
earphone for around 8 seconds until
the LED indicator ashing red and
blue alternately (or take the earphone
out of the charging capsule and wait
for the LED indicator ofthe earphone
ashing red and blue alternate-
ly.),doubleclick the touch control
button and the LED indicator will
ash red and blue once at the same
time,reset the factory setting and the
earphone will power o after the
operation.
Remark: if the Master and Slaver
clear the paring list at the same time,
you have to pairing as st time use
then both earbuds can pairing as
TWS. In order to operation easier we
recommended clear the earbuds
pairing list one by one.
Remove the integrated battery
7 Notice
Hereby, MMD Hong Kong Holding Limited
declares that this product is in compli-
ance with the essential requirements and
other relevant provisions of Directive
2014/53/EU. You can nd the Declaration
of Conformity on www.p4c.philips.com.
Declaration of conformity
Disposal of your old
product and battery
Your product is designed and manufac-
tured with high quality materials and
components, which can be recycled and
reused.
This symbol on a product means that
the product is covered by European
Directive 2012/19/EU.
This symbol means that the product
contains a built-in rechargeable battery
covered by European Directive
2013/56/EU which cannot be disposed
of with normal household waste. We
strongly advise you to take your product
to an ocial collection point or a Philips
service centre to have a professional
remove the rechargeable battery.
Inform yourself about the local separate
collection system for electrical and
electronic products and rechargeable
batteries. Follow local rules and never
dispose of the product and rechargeable
batteries with normal household waste.
Correct disposal of old products and
rechargeable batteries helps prevent
If there is no collection/recycling system
for electronic products in your country,
you can protect the environment by
removing and recycling the battery
before disposing the headphones.
• Make sure the earpieces is discon-
nected from the charging case
before removing the battery.
• Make sure the charging case is
disconnected from the USB
charging cable before removing the
battery.
1
2
3
negative consequences for the environ-
ment and human health.
Environmental information
All unnecessary packaging has been
omitted. We have tried to make the
packaging easy to separate into three
materials: cardboard (box), polystyrene
foam (buer) and polyethylene (bags,
protective foam sheet.)
Your system consists of materials which
can be recycled and reused if disassem-
bled by a specialized company. Please
observe the local regulations regarding
the disposal of packaging materials,
exhausted batteries and old equipment.
Notice of compliance
The device complies with the FCC rules,
Part 15. Operation is subject to the
following two conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any
interference received, including
interference that may cause
undesired operation.
FCC rules
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to part
15 of the FCC Rules. These limits are
designed to provide reasonable protec-
tion against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed
and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or
television reception, which can be
determined by turning the equipment o
and on, the user is encouraged to try to
correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between
equipment and receiver
Connect the equipment into an outlet
on a circuit dierent from that to which
the receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC
radiation exposure limits set forth for an
uncontrolled environment.
This transmitter must not be co-located
or operating in conjunction with any
other antenna or transmitter.
Canada:
This device contains licence-exempt
transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Develop-
ment Canada’s licence-exempt RSS(s).
Operation is subject to the following two
conditions: (1)This device may not cause
interference. (2)This device must accept any
interference, including interference that may
cause undesired operation of the device.
L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et
Développement économique Canada
applicables aux appareils radio exempts de
licence.
Caution:
The user is cautioned that
changes or modications not expressly
approved by the party responsible for
compliance could void the user's
authority to operate the equipment.
IC Radiation Exposure Statement:
This equipment complies with Canada
radiation exposure limits set forth for
uncontrolled environments.
This transmitter must not be co-located
or operating in conjunction with any
other antenna or transmitter.
L’exploitation est autorisée aux deux
conditions suivantes : (1) L’appareil ne doit
pas produire de brouillage; (2) L’appareil doit
accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en
compromettre le fonctionnement.
CAN ICES-3(B)/NMB-3(B)
8 Frequently
asked
questions
My Bluetooth earpieces does not turn on.
The battery level is low. Charge the
earpieces.
I cannot pair my Bluetooth earpieces with
my Bluetooth device.
The Bluetooth is disabled. Enable the
Bluetooth feature on your Bluetooth
device and turn on the Bluetooth device
before you turn on the earpieces.
Pairing does not work.
• Put both earpiecess into charging
case.
• Make sure you have disabled the
Bluetooth function of any previously
connected Bluetooth devices.
• On your Bluetooth device, delete
“Philips ST702” from the Bluetooth
list.
• Pair your earpieces (see ‘Pair the
earpieces with your Bluetooth device
at the rst time’ on page 6).
How to reset pairing.
Take both earpiecess out of the charging
case. Press twice on both earpiecess
Multi-function buttons until the LED
indicator turns white, wait for about 10
seconds. You will hear “Connected”, “Left
Channel”, “Right Channel”, as pairing
successful.
The Bluetooth device cannot nd the
earpieces.
• The earpieces may be connected to a
previously paired device. Turn o the
connected device or move it out of
range.
• Pairing may have been reset or the
earpieces has been previously paired
with another device. Pair the
earpieces with the Bluetoot device
again as described in the user manual.
(see ‘Pair the earpieces with your
Bluetooth device at the st time’ on
page 6).
My Bluetooth earpieces is connected to a
Bluetooth stereo enabled mobile phone,
but music only plays on the mobile phone
speaker.
Refer to the user manual of your mobile
phone. Select to listen to music through
the earpieces.
The audio quality is poor and crackling
noise can be heard.
• The Bluetooth device is out of range.
Reduce the distance between your
earpieces and Bluetooth device, or
remove obstacles between them.
• Charge your earpieces.
The audio quality is poor when streaming
from the mobile phone is very slow, or
audio streaming does not work at all.
Make sure your mobile phone not only
supports (mono) HSP/HFP but alos
supports A2DP and is BT4.0x (or higher)
compatible (see ‘Technical data’ on page
10).
I hear but cannot control music on my
Bluetooth device (e.g. play/pause/skip
forward/backward).
Make sure the Bluetooth audio source
supports AVRCP (see ‘Technical data’ on
page 10).
The volume level of the earpieces is toot
low.
Some Bluetooth devices cannot link the
volume level with the earpieces through
volume sync. In this case, you have to
adjust the volume on your Bluetooth
device independently to achieve an
appropriate volume level.
I cannot connect the earpieces to another
device, what do I do?
• make sure the Bluetooth function of
the previous paired device is turned
o.
• Repeat the pairing procedure on your
second device (see ‘Pair the earpieces
with your Bluetooth device at the
rst time’ on page 6).
I hear sound from only one earpieces.
• If you are in a call, it is normal that
sound comes from the right and left
earpieces.
• If you are listening to music but sound
only comes from one earpieces:
• The other earpieces may be out of
battery. For optimal performance,
charge both earpieces fully.
• The right and left earpiecess are
disconnected from each other,
Turn o both earpieces rst. Then
put both earpiecess back to
charging case for 5 seconds and
take them out. This will turn the
earpiecess on and connect the
two earpiecess. Reconnect the
earpieces to your Bluetooth
device.
• The earpieces is connected to
more than one Bluetooth device.
Switch o the Bluetooth function
of all connected devices. Turn o
both earpiecess. Put both
earpiecess back to charging case
for 5 seconds and take them out.
Reconnect the earpieces to your
Bluetooth device. Note that the
earpieces is desighed for
connecting to only one Bluetooth
device ath a time. When you
reconnect the earpieces to your
Bluetooth device, make sure the
Bluetooth function of any other
Previously paired/connected
devices are o.
• If the above solutions do not help,
factory reset the earpieces (see
‘Factory reset the earpieces’ on
page 9).
For further support, visit
www.philips.com/support.
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode
causar interferência em sistemas devidamente autorizados.
Este produto está homologado pela ANATEL, de acordo com os procedimentos
regulamentados pela Resolução 242/2000, e atende aos requisitos técnicas aplicados. Para
maiores informações, consulte a site da ANATEL: www.anatel.gov.br
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips N.V. and are used under license. This product has been
manufactured by and is sold under the responsibility of MMD Hong Kong
Holding Limited or one of its aliates, and MMD Hong Kong Holding
Limited is the warrantor in relation to this product.
UM_TAST702_00_EN_v0.1