Rowenta First Class User Manual
Displayed below is the user manual for First Class by Rowenta which is a product in the Irons category. This manual has pages.
Related Manuals
EN
DE
FR
NL
DA
NO
SV
FI
IT
ES
PT
EL
AR
www.rowenta.com
DA1500
1103910128 DA1510 F2_110x220mm 18/02/13 13:27 Page1
ON
OFF
120V 240V
00
0
0
0
0
0
0
0
0
0
0
0
0
0
4
5
3
2
1
6
7
8
9
1103910128 DA1510 F2_110x220mm 18/02/13 13:27 Page2
3
EN
SAFETY INSTRUCTIONS
• Please read these instructions carefully and
keep them for further references.
• Never leave the appliance unattended when
it is connected to a power source; if it has not
cooled down for approximately 1 hour.
• The iron must be used and rested on a flat,
stable, heat-resistant surface.
• When you place the iron on the iron rest,
make sure that the surface on which you
place it is stable.
• Always unplug your appliance: before filling,
or rinsing the water tank, before cleaning it,
after each use.
• Children must be supervised to ensure that
they do not play with the appliance.
• Keep the iron and its cord out of reach of
children less than 8 years of age when it is
energized or cooling down.
• This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, if they have been given
supervision or instruction concerning use of
the appliance in a save way and understand
the hazards involved.
• Cleaning and user maintenance shall not be
made by children without supervision.
• The appliance must not be used if it has
fallen to the floor, shows evident of damage,
leaks or fails to function correctly. Never
dismantle you appliance. To avoid any
danger, have it inspected in an approved
service centre.
• The surfaces which are marked with this
sign and the soleplate are very hot
during the use of the appliances. Don’t
touch these surfaces before the iron is
cooled down.
• The iron is not intended for regular use.
1103910128 DA1510 F2_110x220mm 18/02/13 13:27 Page3
IMPORTANT RECOMMANDATIONS
• The voltage of your electrical installation must correspond to that of the iron (220-
240V). Always plug your iron into an earth socket. Connecting to the wrong voltage
may cause irreversible damage to the iron and will invalidate the guarantee.
• If you are using a mains extension lead, ensure that it is corrected rated (16A) with
an earth, and is fully extended.
• If the electric power cord is damaged, it must be replaced by an Approved Service
Centre in order to prevent any danger.
• Do not unplug your appliance by pulling on the cord.
• Never immerse your steam iron in water or any other liquid. Never hold it under the
water tap.
• Never touch the electric cord with the soleplate of the iron.
• Your appliance gives off steam, which may cause burns, especially when you are
ironing close to the edge of your ironing board.
• Never direct the steam towards people or animals.
• For your saftey, this appliance conforms to the applicable standards and regulations
(Low Voltage, Electromagnetic Compatibility, Environmental Directives).
• This product has been designed for domestic use only. Any commercial use,
inappropriate use or failure to comply with the instructions, the manufacturer accepts
no responsibility and the guarantee will not apply.
ENVIRONMENT PROTECTION FIRST !
Your appliance contains valuable materials which can be recovered or
recycled.
Leave it at a local civic waste collection point.
Keep these instructions
4
ON
OFF
120V 240V
00
ON
OFF
120V 240V
0
0
BEFORE IRONING
Remove the sticker on the soleplate.
Adjust the voltage selector.
• Adjust the iron to correct voltage for
your location, using a sharp object.
If the voltage selected is 120 V, the iron
will operate at 100 to 120 V.
If it is set at 240 V, the iron will operate
at 200 to 240 V.
Put the handle into the ironing position.
• Press the release button on the`
rear side and raise the handle
until it locks into position.
• For storing proceed in the same
way to close the handle.
STEAM IRONING
Filling the water tank.
1. Voltage selector
(120/240 V)
2. Temperature control
3. Steam switch
4. High precision tip
5. Microsteam200 soleplate
6. Handle water tank
7. Water filling inlet
8. Burst of steam button
9. Handle release
120V 240V
DESCRIPTION
Note!
If necessary, check that you are using an adapter which meets the safety
requirements of the country you are in.
1103910128 DA1510 F2_110x220mm 18/02/13 13:27 Page4
5
EN
USING BURST OF STEAM AND VERTICAL
STEAM
To remove
creases
vertically.
To remove
difficult
creases.
2 min
ON
OFF
ON
OFF
110V 220V
MAX
ON
OFF
110V 220V
0
0
ON
OFF
110V 220V
Setting the temperature.
Your iron has been designed to operate using untreated tap water.
Steam
ironing
Steam control
set to
Temperature
set to
•••
Cotton
Linen
Burst
of steam
Note !
Your iron will only produce steam when the control is set within the
coloured zone.
Hold the iron a few centimeters away from the garment to avoid burning
delicate fabrics.
IMPORTANT Never direct the steam at people or animals !
ON
OFF
110V 220V
ON
OFF
ON
OFF
120V 240V
NO
OK
ON
OFF
110V 220V
00
0
0
0
0
0
00
0
0
0
0
0
NO
1103910128 DA1510 F2_110x220mm 18/02/13 13:27 Page5
6
DRY IRONING
MAINTENANCE AND STORING OF YOUR IRON
Cleaning your iron.
ON
OFF
ON
OFF
110V 220V
0
0
Dry
ironing
Steam control
set to
Temperature
set to
•
••
•••
Silk,
Synthetics
Wool
Burst of steam
Temperature
at setting
•••
ON
OFF
110V 220V
10 min
ON
OFF
NO
ON
OFF
110V 220V
NO
NO
Our advice :
With the iron in DRY mode, start by ironing fabrics at a low temperature (•)
before moving on to those requiring a higher temperature (•••).
If you turn the temperature control down, wait for approximately one
minute before ironing again. If you are ironing fabrics made from mixed
fibres : set the iron temperature to the correct level for the most delicate
fibre.
Note ! Make sure the iron is cold before storing it.
Do not use any cleaning or descaling products.
IMPORTANT Do not wind the cord around the hot soleplate.
Never store your iron placed down on the soleplate.
1103910128 DA1510 F2_110x220mm 18/02/13 13:27 Page6
7
Storing your
iron.
ON
OFF
120V 240V
0
0
110V 240V
00
ON
OFF
NO
10 min
ON
OFF
110V 220V
Problems
and possible causes Solutions
Your iron produces little or no steam
• The temperature selected is too low.
• The steam control is set on OFF.
• There is no water in the tank.
Set the temperature control on •••
Switch the steam control to ON.
Fill the water tank.
Water is dripping from the holes in the soleplate
• You have been using the burst of
steam button too often.
• Steam is used before the iron is hot
enough.
• The iron is stored with water in th
tank.
Wait a few seconds between each
shot.
Set the thermostat within the coloured
steam zone and wait until the iron is
hot (approx. 2 min.).
Empty the tank before storing the iron
and set the steam control to OFF.
• The problem persists. Take your iron to an Approved
Service Centre.
HELPLINE:
if you have any product problems or queries, please contact our Customer Relations
Team first for expert help and advice:
0845 602 1454 - UK
(01) 677 4003 - Ireland
or consult our website - www.rowenta.co.uk
EN
1103910128 DA1510 F2_110x220mm 18/02/13 13:27 Page7
1103910128 - 06/13 - DA1500 F2
1103910128 DA1510 F2_110x220mm 18/02/13 13:29 Page72