Table of Contents
Schneider Electric MTN6725-0101 User Manual
Displayed below is the user manual for MTN6725-0101 by Schneider Electric which is a product in the Gateways/Controllers category. This manual has pages.
Related Manuals
www.se.com
SpaceLogic KNX
SpaceLogic KNX DALI Gateway Pro
Product Information
This document is based on the installation instructions and gives you further product
information about the SpaceLogic KNX DALI Gateway Pro.
MTN6725-0101
06/2020
2 MTN6725-0101
06/2020
SpaceLogic KNX
Legal information
The Schneider Electric brand and any trademarks of Schneider Electric SE and its
subsidiaries referred to in this guide are the property of Schneider Electric SE or its
subsidiaries. All other brands may be trademarks of their respective owners.
This guide and its content are protected under applicable copyright laws and furnis-
hed for informational use only. No part of this guide may be reproduced or transmit-
ted in any form or by any means (electronic, mechanical, photocopying, recording,
or otherwise), for any purpose, without the prior written permission of Schneider
Electric.
Schneider Electric does not grant any right or license for commercial use of the
guide or its content, except for a non-exclusive and personal license to consult it
on an “as is” basis. Schneider Electric products and equipment should be installed,
operated, serviced, and maintained only by qualied personnel.
As standards, specications, and designs change from time to time, information
contained in this guide may be subject to change without notice.
To the extent permitted by applicable law, no responsibility or liability is assumed by
Schneider Electric and its subsidiaries for any errors or omissions in the informa-
tional content of this material or consequences arising out of or resulting from the
use of the information contained herein.
3
06/2020 MTN6725-0101
SpaceLogic KNX
Warnings
Read these instructions carefully and look at the equipment to become familiar with
the device before trying to install, operate, service, or maintain it. The following
special messages may appear throughout this manual or on the equipment to warn
of potential hazards or to call attention to information that claries or simplies a
procedure.
The addition of either symbol to a “Danger” or “Warning” safety label indicates
that an electrical hazard exists which will result in personal injury if the instruc-
tions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that accompany this symbol to avoid possible
injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result
in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury
NOTICE
NOTICE is used to address practices not related to physical injury.
Additonal notes
The specied information must be followed, otherwise a program or data error
may occur
Your will nd additional information here to make your work easier.
406/2020 MTN6725-0101
Table of contents SpaceLogic KNX
Table of contents
1 Getting to know the SpaceLogic KNX Gateway Pro ....... 6
1.1 ETS Functions ..............................................6
1.2 Commissioning..............................................7
2 Connections and operating elements ................... 8
3 Technical Data...................................... 9
ToC
5
06/2020 MTN6725-0101
SpaceLogic KNX
About this document
All information on safe installation and safe connection can only be found in the
installation instructions.
This document gives you further product information about the SpaceLogic KNX
DALI Gateway Pro.
For your safety
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH.
Safe electrical installation must be carried out only by skilled profession-
als. Skilled professionals must prove profound knowledge in the following
areas:
•Connecting to installation networks
•Connecting several electrical devices
•Laying electric cables
•Connecting and establishing KNX networks
•Safety standards, local wiring rules and regulations
Failure to follow these instructions will result in death or serious injury.
606/2020 MTN6725-0101
Getting to know the SpaceLogic KNX Gateway Pro SpaceLogic KNX
1 Getting to know the
SpaceLogic KNX Gateway
Pro
The SpaceLogic KNX Gateway Pro (hereafter referred to gateway) is a multi-mas-
ter application controller for controlling electronic ballasts with DALI interface via
the KNX installation bus. It supports ballasts according to EN 62386-102 ed1
(DALI1), devices according to EN 62386-102 ed2 (DALI2), as well as DALI2 motion
sensors and light sensors according to EN 62386-303 and EN 62386-304.
The device transforms switching and dimming commands from the connected KNX
system into corresponding DALI telegrams, or status and event information from
the DALI bus into KNX telegrams.
The gateway has a DALI output which can control up to 64 ECGs. In addition, up to
8 DALI2 motion detectors or light sensors can be connected. Multi-master opera-
tion according to EN 62386-103 ed2 is permitted.
The required power supply for the connected ECGs and motion sensors is provided
directly from the device. Additional DALI power supplies are not required
When using sensors supplied via the DALI bus, it must be ensured that the current
consumption of all connected DALI devices does not exceed the guaranteed
value.
The device is available in a 4TE wide DIN rail housing for direct installation in
an electrical distribution board. The bus connection is made via a standard bus
connector. Mains and DALI lines are connected via screw terminals on the device.
Ethernet is connected via an RJ45 socket.
Per gateway the ECGs can be controlled in 16 groups. In addition to the group
control the gateway also allows individual control of up to 64 ECGs.
In addition to the control of all standard operating devices, the gateway also allows
the operation of single battery emergency lights (EN 62386-202). Emergency light-
ing systems with central battery are also supported.
A maximum of 8 motion detectors with light sensors can also be controlled.
The special interface for conguring the DALI segments is designed as a DCA
(Device Control App) for the ETS 5. Please make sure that the corresponding
etsapp is installed in addition to the product database knxprod. This is available for
download at Konnex or on the Schneider Electric website.
1.1 ETS Functions
Which functions you can set in the ETS as well as a detailed description of the
parameters and values can be found in the ETS application description. -> ETS
application description
• Addressing of 16 DALI groups and/or individual addressing of up to 64 individu-
al ECGs
• Flexible DALI commissioning concept: directly on the device, via integrated web
server or in the ETS5 (DCA)
• Coloured light control with the support of Device Type 8 (DT-8) ballasts and
control via communication objects
7
06/2020 MTN6725-0101
Getting to know the SpaceLogic KNX Gateway Pro SpaceLogic KNX
•Coloured light control depending on ballast Sub-Type:
– Colour Temperatur (DT-8 Sub-Type Tc)
– XY Colour (DT-8 Sub-Type XY)
– RGB (DT-8 Sub-Type RGBWAF)
– HSV (DT-8 Sub-Type RGBWAF)
– RGBW (DT-8 Sub-Type RGBWAF)
• Automatic, time-controlled setting of light value, light colour and colour tempera-
ture (also for Human Centric Lighting appli-cations) for groups and/or individual
ECGs
• Automatic change of colour temperature depending on the light value (Dimm-
To-Cold)
• Control of colour temperature via communication object for DT6, warm white
and cool white
• Broadcast objects for controlling all connected ECGs simultaneously (also pos-
sible for color values)
• Various operating modes for groups such as continuous mode, night mode,
staircase mode
• Integrated operating hours counter for each group and/or individual ECG with
alarm when end of life is reached
• Individual fault detection with objects for each individual luminaire/EVG
• Complex error evaluation on group/device level with error number and error rate
calculation
• Error threshold monitoring with individually adjustable threshold values
• Scene module for up to 16 scenes, which can be assigned to KNX scenes 1..64
as required
• Extensive scene programming, including the possibility of dimming scenes
• Setting of colour in DT-8 luminaires via scenes for groups and/or individual
ECGs
• Eect module for sequence controls and lighting eects including colour adjust-
ment in DT-8 luminaires
• Test mode for systems with emergency luminaires supplied by central battery
• Support of single-battery emergency lights DT-1
• Support of test procedures for emergency lights with time and date stamp
• “Quick Exchange Function” for easy replacement of individual defective ECGs
• “Energy saving function” allows the ECG power supply to be switched o when
light is switched o via additional switch-ing actuators
• Integrated web server with extensive options for commissioning and mainte-
nance
• Integrated “Visualization” via Web browser for direct operation and display
• Cross-device summary of errors in the entire system
• Manual operation of group and broadcast telegrams via operating keys and
display on the device
• Signalling of error states and status diagnosis via LEDs and display on the de-
vice
1.2 Commissioning
After complete connection and switching on the supply voltage, the gateway can
now be commissioned and programmed with the ETS 5, including the necessary
etsapp. Please refer to the application description for the execution of these further
procedures. -> ETS application description
806/2020 MTN6725-0101
Connections and operating elements SpaceLogic KNX
2 Connections and operating
elements
The device connections, as well as the elements learn button and programming
LED required for KNX commissioning are only accessible in the distribution board
when the cover is removed.
The buttons required for DALI commissioning and parameterisation (MOVE, Prg/
Set, ESC), as well as reading the 2-line display and the control LEDs (ERR and
LNK) can be operated with the distribution board cover closed.
LNK
ERR
ESCPrg/SetMove
A
B
C
D
E
F
G
H
IJ
A KNX bus connection terminal
B Error-LED
C Ethernet-LNK-LED
D Mains connection
E RJ-45 socket
F Display
G Operating/programming buttons
H DALI output terminals
I KNX Programming button
J KNX Programming LED
9
06/2020 MTN6725-0101
Technical Data SpaceLogic KNX
3 Technical Data
Power supply
Mains volate: AC/DC 100-240 V, 50-60 Hz
Maximum power consump: max. 8 W
Bus power supply via KNX bus: DC 24 V (SELV), ca. 5 mA
Connectors
Mains connector L N PE: Screw connector 3x 0.5- 4 mm² single or threaded core
DALI-Bus : Screw connector 2x 0.4-4 mm² single or threaded core
KNX: KNX Bus connector
Ethernet: RJ-45
Control elements
KNX-Programming button: Normal-/Adressing mode
Buttons (Move, Prg/Set, ESC): for manual control and for activation of broadcast and service
functionn
Display elements
Programming LED red: Indicates normal-/adressing mode
LNK-LED yellow: Signals device Ethernet readiness
ERR-LED red: Signals fault status
LC-Display 2x12 characters: for conguration menu manual operation and devive adjustments
KNX
KNX Medium: Twisted Pair
Security: KNX Data Secure Ready
DALI
Outputs: 1 output D+/D-
Output type: Multi-Master Application Controller according to EN 62386-103
ed 2
Number ballasts: max. 64 ECGs according to EN 62386-101 ed1 and ed 2
Number sensors: max. 8 motion detectors and sensors according to EN 62386-
303 / -304
DALI voltage: typical DC 18 V, short-circuit proof max. 250 mA, basic insulation
(no SELV)
Recommended wire cross-sec-
tion:
min. 1.5 mm²
Guaranteed supply current: 160 mA
Maximum supply current 250 mA
Shutdown delay: 600ms after DALI short circuit shutdown occurs
Start-up attempt after shutdown: 5s after short-circuit detection
10 06/2020 MTN6725-0101
Technical Data SpaceLogic KNX
Ethernet
Type: 100BaseT (100 Mbit/s)
IP address allocation: via DHCP service or xed IP address
Mechanical data
Material casing: Plastic PC
Width: 4 TE = 72 mm
Dimensions WxHxD (mm): 72x65x90 mm
Weight 180 g
Elektrische safety
Protection type (in accordance with EN 60529): IP20
Protection class (according to IEC 1140): I
Overvoltage category: III
Pollution class (in accordance with EN60664-1): 2
KNX Bus: DC 24 V (SELV)
DALI Bus: typical DC 18 V, 250 mA base isolation, (no SELV)
EMV requirements
Complies with directive 2014 / 30 / EU
Environmental conditions
Environmental conditions during operation: -5 °C to +45 °C
Storage temperatue: -25 °C to +55 °C
Transportation temperature: -25 °C to +70 °C
Relative humidity (non condensing: 5 % to 95 %
Approbation
KNX certied
DIIA certied according to EN 62386-101 ed 2 and EN 62386-103 ed 2
CE-Signage
According to EMC-Guidelines (Residential and commercial buildings), Low Voltage guidelines
MTN6725_0101_HWadd_EN
Schneider Electric Industries SAS
If you have technical questions, please contact the
Customer Care Centre in your country.
se.com/contact
© 2020 Schneider Electric, all rights reserved
06/2020