StarTech.com ARMPIVOT User Manual
Displayed below is the user manual for ARMPIVOT by StarTech.com which is a product in the Monitor Mounts & Stands category. This manual has pages.
Related Manuals
Manual Revision: 12/04/2018
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
ARMPIVOT
Desk Mount Monitor Arm with Cable
Management & Height Adjust
*actual product may vary from photos
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Introduction ............................................................................................ 1
Packaging Contents ................................................................................................................................. 1
Product Diagram ....................................................................................2
Installation ..............................................................................................2
Desk / Grommet Mounting ................................................................................................................... 2
Attaching the Display .............................................................................................................................. 5
Completing the Assembly ..................................................................................................................... 6
Adjusting Monitor Mount Resistance ................................................................................................ 7
Specications .......................................................................................... 8
Technical Support ..................................................................................9
Warranty Information ............................................................................ 9
Instruction Manual
1
Introduction
Packaging Contents
Support Post
Qty: 1
Monitor Mount
Qty: 1
Large C Clamp
Qty: 1
EVA Cushion
Qty: 1
Cable Clip / Collar
(attached)
Qty: 1
Thumb Screws
Qty: 4
M6x12mm Phillips Screws
Qty: 4
M5x14mm Hex Screws
Qty: 4
M4x15mm Phillips Screw
Qty: 1
Male Round Washer
Qty: 1
Female Round Washer
Qty: 1
Hand Screw
(attached)
Qty: 1
Pressure Plate
(attached)
Qty: 1
M3 (2.5mm) Allen Wrench
Qty: 1
Small C Clamp
Qty: 1
3
4 5 6
7 8 9
10 11 12
13 14 15
21
Instruction Manual
2
Product Diagram
Installation
Desk / Grommet Mounting
Warning: It is the installer’s responsibility to ensure that the combined weight of all
components does not exceed the maximum 14 kg (30.9 lbs) weight capacity of the
mounting arm.
The Monitor Arm can be clamped to a desk / table, or mounted through a grommet
hole. Instructions for both will be provided in the following sections.
Instruction Manual
3
Grommet Mount
Desk Mount
1. Remove the Hand Screw (13) from the base of the Support Post (1).
2. Place the EVA Cushion (4) beneath the Support Post (1) and thread the Hand Screw
(13) from below until secure. Ensure that the Pressure Plate (14) is making full
contact with the desk surface.
1. Attach the Large C Clamp (3) and Small C Clamp (6) pieces using 4 M6x12mm
Screws (8) as shown, depending on the thickness of your desk / table.
Instruction Manual
4
2. Slide the Hand Screw (13) through the bottom of the clamp and attach the Pressure
Plate (14) using the Male Round Washer (11), Female Round Washer (12) and
M4x15mm Phillips Screw (10).
3. Attach the completed Desk Clamp to base of the Support Post (1) using 4 M5x14mm
Hex Screws (9).
4. Place the EVA Cushion (4) beneath the Support Post (1) and then place the Desk
Clamp opening around the edge of your desktop in your desired location. Tighten by
hand to secure, ensuring that the clamp is making full contact with the desk surface.
Instruction Manual
5
Attaching the Display
1. Carefully place your display face down on a protective surface to access the
mounting points.
2. Attach the display to the Monitor Mount (2) using the 4 Thumb Screws (5).
Instruction Manual
6
WARNING! Do not over-tighten the screws and stop immediately if you encounter
resistance to avoid damage to your display. Ensure that all spacers and screws being
used are the same length and thread type.
Completing the Assembly
1. Loosen the Cable Clip / Collar (7) on the Support Post (1) and adjust to the
desired height.
2. Slide the Monitor Mount (2) onto the Support Post (1) until it rests on the Collar (7)
and tighten the set screw using the M3 Allen Wrench (15).
Instruction Manual
7
Adjusting Monitor Mount Resistance
WARNING! Forced movement of the Mount Bracket without loosening the screws may
damage the product or the mounted displays.
Always support your display from underneath when making any adjustments to the
LCD Arms or Mount Brackets to avoid damage to the display.
Note: For all adjustments outlined below, turning the screw clockwise will increase the
resistance, while turning the screw counter-clockwise will decrease resistance.
To increase / decrease the tilt resistance, adjust the set screw located on the side of the
Monitor Mount joint, using the M3 Allen Wrench (15).
To increase / decrease swivel resistance, adjust the set screw located on the side of the
Monitor Mount bracket at the Support Post, using the M3 Allen Wrench (15).
Place the wrench in the collar when not in use.
Instruction Manual
8
Specications
Weight Capacity 30.9 lbs (14 kg)
Max Display Size 30”
VESA Compatibility 75x75 mm and 100x100 mm
Maximum Mounting Surface
Thickness 4 in (100 mm)
Instruction Manual
9
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a ve-year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.