Techly I-WL-REPEATER User Manual
Displayed below is the user manual for I-WL-REPEATER by Techly which is a product in the Bridges & Repeaters category. This manual has pages.
Related Manuals
Wireless-N Wifi Repeater04Wireless-N Wifi Repeater03Wireless-N Wifi Repeater02A1. Plug the Wi-Fi Repeater to a wall socket.
How to configure the Wi-Fi RepeaterYou will need WiFi AP/Router Internet access You will need broadband Router Internet access Connect the WiFi-Repeater to your Router/Switch with RJ-45 CableGetting StartedWireless-N Wifi Repeater01Introduction：A6. Select your SSID to continue.WirelessA7. of your network. When you see below, please do not change any setting but only insert the key Wireless-N Wifi Repeater05Wireless-N Wifi Repeater064. The following message will be displayed on your web browser:Wireless-N Wifi Repeater07展开尺寸:360 x 240 mm成品尺寸:120 x 90 mmThe WiFi Repeater is a combined wired/wireless network connection device designed specifically for small business, office, and home office networking requirements. It allows a wireless network to be expanded using multiple access points without the need for a wired backbone to link them. It also works well with other 11b/g and 11n protocol wireless products.NOTE:reset 10 If you need to the Wi-Fi Repeater, you need press and hold the reset button inside the tiny hole for seconds.A2. Click on the network icon ( or ) on the right bottom of your desktop. You will find the signal from the Wi-Fi Repeater. Click on ‘Connect’ and wait for a few seconds.
A3. Open web browser and type http://192.168.10.1 in the browser's address box. This number is the default IP address for this device.
A4. The login screen below will appear. Enter the “User Name” and “Password” then click “OK” to login. The default User name is “admin” and Password is “admin”.A5. After logging in, you will see the web page below: Click on ‘Repeater’ to continue.Click on ‘Apply’ button, The Repeater will restart. Wait for a few seconds your Wi-Fi Repeater is ready for use.* The default wireless SSID and Security key of Wi-Fi Repeater is same as your AP/router.B. Configure the Wi-Fi Repeater with RJ45 Cable.1. Plug the Wi-Fi Repeater to a wall socket. Connect your computer / laptop with the Wi-Fi Repeater with enclosed RJ45 Cable.2. Follow process A3 to A7 to configure your Wi-Fi Repeater.C. Configure the Wireless AP Mode.1. Plug the Wi-Fi Repeater into a wall socket.2. Follow process A3 to A4.3. Click on ‘AP’ to continue.Note: Please check whether the WiFi-Repeater accord with factory default settings once you can’t download http://192.168.10.1. If you are still not sure what reasons, you can reset the WiFi-Repeater, just need to press the button for seconds, then try again.reset10
WiFi-RepeaterUser ManualREV.3.2You can configure the Wi-Fi Repeater by connecting it with your computer/laptop with enclosed RJ45 cable or wirelessly. A. Configure the Wi-Fi Repeater wirelessly.Click on ‘Apply’ button, The Repeater will restart. Wait a few seconds your Wi-Fi Repeater is ready for use.SSIDChannelSecurity type the "SSID" of your wireless network.Auto (recommend)Setup the wireless security and encryption to prevent from unauthorized access and monitoring. Supports 64/128-bit WEP, WPA, WPA2, WPA/WPA2 encryption methods.Wireless Repeater ModeWireless AP ModeBefore you starting to use this router, please check if there’s anything missing in the package, and contact your dealer of purchase to claim for missing items:· 1 x Wireless-N Repeater· 1 x RJ-45 Networking Cable· 1 x Quick installation GuidePackage ContentsSecurity keythe "Password" of your wireless network.
Reset
ResetRJ45 PortPower IndicatorWPS Indicator(Optional)Wireless IndicatorLAN IndicatorWPS Button(Optional)Open Source Code This product includes software codes developed by third parties. These software codes are subject to either the GNU General Public License (GPL), Version 2, June 1991 or the GNU Lesser General Public License (LGPL), Version 2.1, February 1999. You can copy, distribute, and/or modify in accordance with the terms and conditions of GPL or LGPL.The source code should be complete, if you think our need to provide any additional source code files under GNU General Public License (GPL), please contact us. We are committed to meeting the requirements of the GNU General Public License (GPL) . You are welcome to contact us local office to get the corresponding software and licenses. Please inform us your contact details and the product code. We will send you a CD with the software and license for free. Please refer to the GNU GPL Web site for further information. http://www.gnu.org/licenses/licenses.en.html.For a typical wireless setup at home (as shown below), please do the following:Setting up a Wireless Infrastructure Network
Wireless-N Wifi Repeater09
How to configure your computer/laptop with the Network IP Address
Wireless-N Wifi Repeater10Wireless-N Wifi Repeater08Wireless-N Wifi RepeaterWireless-N Wifi Repeater13Change Management passwordWireless-N Wifi Repeater14Firmware UpgradeWireless-N Wifi Repeater15Factory Default and Settings Backup , RestoreConfiguring via Web Browser Wireless-N Wifi Repeater11How to connect your computer/laptop with the Wi-Fi Repeater Adding a Wireless computers to the WiFi-Repeater1. Log on to the computer.2. Open Connect to a Network by right-clicking the network icon ( or ) in the otification area. 3. Choose the wireless network from the list that appears, and then click Connect.4. Type the network security key or passphrase if you are asked to do so, and then click OK. You'll see a confirmation message when you are connected to the network.
(
(
(
(
(
(
(
(
(
For more information: http://windows.microsoft.com/en-US/windows7/Add-a-device-or-computer-to-a-network http://windows.microsoft.com/en-US/windows7/Setting-up-a-wireless-network http://windows.microsoft.com/en-US/windows-vista/Setting-up-a-wireless-network Adding a Wireless computers to the WiFi-Repeater with WPS Button 1. Log on to the computer.2. Press the WPS button of the WiFi Repeater directly for 2 - 3 seconds.3. Press the WPS button of the Wireless Adapter directly for 2 - 3 seconds. Click Finish to complete the WPS configuration. (Please check your Wireless adapter Manual with WPS configuration)4. You should see icons for the computer you added and for the other computers and devices that are part of the network.Adding a wired (Ethernet) computer to the WiFi-Repeater1. Plug the Wi-Fi Repeater to a wall socket. Connect your computer / laptop with the Wi-Fi Repeater with enclosed RJ45 Cable. 2. To confirm that you added the computer, do the following:Open Network by clicking the Start button , and then clicking Control Panel. In the search box, type network, and then, under Network and Sharing Center, click View network computers and devices. You should see icons for the computer you added and for the other computers and devices that are part of the network.
r
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
1. Log on to the computer.2. Click the “Start” button (it should be located at the lower-left corner of your screen), then click “Control Panel”. Click “View Network Status and Tasks”, and then click “Manage Network Connections”. Right-click “Local Area Network”, then select “Properties”. When the “Local Area Connection Properties” window appears, select “Internet Protocol Version 4 (TCP/IPv4)” and then click “Properties”. 3. Setting IP address manually: Type IP address is 192.168.10.x (x is from 2 to 254), and Subnet mask is 255.255.255.0. Type the Router’s LAN IP address (the default IP is 192.168.10.1) into the Default gateway field.
lick
hen
hen
”
tocol
In AP mode and click “Wireless -> Basic Settings” located at the web management interface, the following message will be displayed on your web browser:You could configure the minimum number of Wireless settings for communication, such as Network Name (SSID) and Channel. The Access Point can be set simply with only the minimum setting items.
In Repeater mode and click “Wireless-> Basic Settings” located at the web management interface, the following message will be displayed on your web browser:Default password of Wireless Router is “admin”, and it’s displayed on the login prompt when accessed from web browser. There’s a security risk if you don’t change the default password, since everyone can see it. This is very important when you have wireless function enabled.To change password, please follow the following instructions:Please click ‘Management -> Password‘ menu on the web management interface, the following message will be displayed on your web browser:If you want to keep original password unchanged, click ‘Cancel’.Click ‘Apply’ button, The WiFi Repeater will log off.The system software used by this router is called as ‘firmware’, just like any applications on your computer, when you replace the old application with a new one, your computer will be equipped with new function. You can also use this firmware upgrade function to add new functions to your router, even fix the bugs of this router. Please click ‘Management-> Upgrade Firmware’ located at the web management interface, and then the following message will be displayed on your web browser: Click ‘Browse…’ or ‘Choose File’ button first; you’ll be prompted to provide the filename of firmware upgrade file. Please download the latest firmware file from our website, and use it to upgrade your router. After a firmware upgrade file is selected, click ‘Upload‘ button, and the router will start firmware upgrade procedure automatically. The procedure may take several minutes, please be patient.NOTE: Never interrupt the upgrade procedure by closing the web browser or physically disconnect your computer from router. If the firmware you uploaded is corrupt, the firmware upgrade will fail, and you may have to return this router to the dealer of purchase to ask for help. (Warranty voids if you interrupted the upgrade procedure). You can backup all Setting of this router to a file, so you can make several copied of router configuration for security reason.
5. To confirm that you added the computer, do the following:Open Network by clicking the Start button , and then clicking Control Panel. In the search box, type network, and then, under Network and Sharing Center, click View network computers and devices. You should see icons for the computer you added and for the other computers and devices that are part of the network.Note : If you don't see icons in the Network folder, then network discovery and file sharing might be turned off.
pute
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do
, do, do, do, do, do, do, do
g Ce
g Ce
g Ce
Wireless Base Configuration – AP ModeAuto (recommend)Setup the wireless security and encryption to prevent from unauthorized access and monitoring. Supports 64/128-bit WEP, WPA, WPA2, WPA/WPA2 encryption methods.Click ‘Apply‘ button, The WiFi Repeater will restart.Wireless On/Offthe "SSID" of your wireless network.Wireless EnableSSIDChannelSecurity type
Wireless Base Configuration – Repeater ModeWireless EnableDeleteRepeater ssidSecurity typeClick ‘Apply’button, The WiFi Repeater will restart.Wireless On/OffRemove the repeater connection profilethe “SSID” of your repeater wireless network.Setup the repeater ssid security type.Click this ‘Load default’ button to remove all settingsSave SettingsLoad SettingsReset SettingsPress ‘Save…’ button, you can please save it as another filename for different versions, and keep it in a safe place. Press ‘Browse…’ to pick a previously-saved configuration file from your computer, and then click ‘Upload…’. After the configuration is uploaded, the router’s configuration will be replaced by the file you just uploaded. To backup or restore router setting, please follow the following instructions:Please click ‘Save/Reload setting’ located at the web management interface, then the following message will be displayed on your web browser:Security keythe "Password" of your wireless network.
the "Password" of your repeater wireless network.Security key12