Whirlpool WH1410 A+E User Manual
Displayed below is the user manual for WH1410 A+E by Whirlpool which is a product in the Freezers category. This manual has pages.
Related Manuals
INSTRUCTIONS FOR USE
1
GB
A. Lid Handle.
B. Lock (if provided).
C. Seal.
D. Defrost water drain plug (depending on model).
E. Control panel.
F. Basket (depending on model).
G. Condenser (located at the rear).
INSTALLATION
• Refer to chapter “Before using the appliance”.
• Unpack the appliance.
• Remove the 4 protection pieces inserted between
lid and appliance.
• Warning: two of the four protection pieces must be
tted in the seat of the condenser plastic supports,
located at the rear of the product.
This is necessary to ensure the correct distance from
the wall.
• Ensure that the defrosting water drainage plug (if
provided) is correctly positioned (D).
• For best operation of the appliance and in order to avoid
damage when the lid is opened, leave a space of at least
7 cm from the rear wall and 7 cm at the sides.
• Fit the accessories (if provided).
1234
1. Red LED: when ashing, it indicates that an alarm
condition is present (see “TROUBLESHOOTING
GUIDE”)
2. Blue LED: the function “6th Sense” is automatically
activated and does not need to be selected by the user,
therefore the blue LED (2) “Sense” always remains
on. For more technical details, refer to paragraph “6th
Sense function”.
3. Green LEDs: they indicate that the appliance is in
operation, and the temperature has been set.
4. Temperature setting button: to adjust the set
temperature and to activate/deactivate the fast freezing
operations.
Clean the inside of the appliance before using it.
Switching on the appliance
• Plug in the appliance.
• The green LED lights up (“Normal”).
• The blue LED lights up (“Sense”).
• The red LED ashes to indicate that the temperature
inside the appliance is not yet suciently low for food
storage. The red LED will normally switch o within the
rst six hours after the appliance is switched on.
• Place food inside the product only when the red LED has
switched o.
Note:
As the seal is tight, the appliance lid cannot be reopened
immediately after closing. Wait a few minutes before
re-opening the lid of the appliance
INSTRUCTIONS FOR USE
2
Temperature adjustment
Use the key (4) to select the desired temperature. To adjust
the internal temperature, proceed as follows:
• Repeatedly press the key (4). Each time the key is
pressed, the set temperature is updated, displaying the
“Normal”, “Eco” and “Max” values in succession.
• Select “ Max” for a colder storage temperature.
• With partial loads “Eco” is recommended: this setting will
optimise energy consumption.
The green indicator lamps (3) indicate the selected setting
according to the following diagram:
Eco: least cold temperature (left
indicator lamp lit).
Normal: intermediate temperature
(right indicator lamp lit).
Max.: extra low temperature (both
indicator lamps lit).
Shopping: Fast Freezing (both
indicator lamps lit). See section
“Freezing fresh food”.
Note:
The settings will be saved in the memory even if
a power cut occurs. The time needed for the temperature
inside the freezer to reach the set value, can vary
depending on climatic conditions and the set temperature
itself.
6th Sense” Function
The “6th Sense” function is always active to control the
internal temperature of the appliance and guarantee the
optimum conditions.
It automatically intervenes in the following cases:
• door opening
This function activates every time the opening of the door
changes the internal temperature of the appliance. The
function remains active for the time needed to reinstate
optimum operating conditions.
• storing food inside the freezer
This function activates every time signicant quantities of
food are introduced. It remains active for the time needed
to reinstate optimum freezing conditions of the food
introduced, ensuring the best compromise between the
quality of the freezing process and energy consumption.
Note:
The duration of the “6th Sense” function is set
automatically, and may vary depending on the way the
product is used.
FREEZING FOOD
Preparation of fresh food for freezing
• Before freezing, wrap and seal fresh food in: aluminium
foil, cling lm, air and water‑tight plastic bags,
polyethylene containers with lids, provided they are
suitable for freezing foods.
• Food must be fresh, mature and of prime quality in order
to obtain high quality frozen food.
• Fresh vegetables and fruit should preferably be frozen
as soon as they are picked to maintain the full original
nutritional value, consistency, colour and avour.
• Always leave hot food to cool before placing in the
appliance.
Freezing fresh food
• Place foods to be frozen in direct contact with the walls
of appliance:
A) - foods to be frozen,
B) - foods already frozen.
• Avoid placing foods to be frozen in direct contact with
food already frozen.
• For best and fastest freezing, foods should be split into
small portions; this will also be useful when the frozen
items are to be used.
• If minimum quantities of food are introduced (up to 1/4
of the maximum freezing power stated on the rating
plate), the operation of the appliance will be controlled
automatically by the “6th Sense” function without any
need for intervention from the user.
• When freezing higher quantities of food, up to the
maximum freezing capacity of the appliance, indicated
on the rating plated, proceed as follows:
1. At least 24 hours before
storing fresh foods inside the
product for freezing, activate
the fast freezing function by
pressing (4) for approximately
3 seconds. The green LEDs (3)
ash in sequence.
2. Introduce the food to freeze
inside the appliance, and
keep the door of the appliance
closed for 24 hours. After this
period the food will be frozen.
The fast freezing function can be
deactivated manually by pressing (4).
If the fast freeze function is not manually deactivated, it
will be automatically deactivated by the appliance after
50 hours.
INSTRUCTIONS FOR USE
3
FOOD STORAGE
Refer to the table on the appliance.
Classication of frozen foods
Put the frozen products into
the appliance and classify
them; The storage date
should be indicated on the
packs, to allow use within
expiry dates.
Advice for storing frozen
food
When purchasing frozen food products:
• Ensure that the packaging is not damaged (frozen
food in damaged packaging may have deteriorated).
If the package is swollen or has damp patches, it may
not have been stored under optimal conditions and
defrosting may have already begun.
• When shopping, leave frozen food purchases until last
and transport the products in a thermally insulated cool
bag.
• Once at home, place the frozen foods immediately in
the appliance.
• Avoid, or reduce temperature variations to the minimum.
Respect the best-before date on the package.
• Always observe the storage information on the package.
Note:
Eat fully or partially defrosted foods immediately.
Do not refreeze unless the food is cooked after it
has thawed. Once cooked, the thawed food can be
refrozen.
If there is a long power failure:
• Do not open the appliance lid except to place ice
packs (if provided) over the frozen foods on the
right and left of the appliance. This will slow down
the rise in temperature.
MONTHS FOOD
DEFROSTING THE APPLIANCE
The appliance should be defrosted when the thickness of
ice on the walls reaches 5-6 mm.
• Disconnect the appliance from the mains power supply.
• Remove the packs of food from the appliance and wrap
them close together in newspaper and store in a very
cool place or thermally insulated bag.
• Leave the appliance lid open.
• Remove the internal defrost
water drain plug (depending
on model).
• Remove the external defrost
water drain plug (depending
on model) and reposition it as
shown in the gure.
• Place a bowl beneath the
drainage channel to collect
the residual water. If available,
use the divider.
• Speed up defrosting by using
a spatula to detach the ice
from the appliance walls.
• Remove the ice from the bottom of the appliance.
• In order to avoid permanent damage to the
appliance interior, do not use pointed or sharp
metal instruments for removing the ice.
• Do not use abrasive products or heat up the interior
articially.
• Dry the interior of the appliance thoroughly.
• On completion of the defrosting, ret the plug.
CHANGING THE LID LIGHT BULB (if provided)
• Disconnect the appliance from the
mains power supply.
• Remove the diuser by following
the sequence of steps shown in
the gure.
• Unscrew the light bulb and replace
it with an identical bulb of the same
wattage and voltage.
• Ret the diuser and plug in the appliance.
TROUBLESHOOTING GUIDE
1. The red LED ashes.
• Is there a power failure?
• Is a defrosting operation in progress?
• Has fresh food recently been introduced?
• Is the appliance lid properly closed?
• Is the appliance placed near a heat source?
• Are the ventilation grille and condenser clean?
2. All LEDs ash at the same time.
• Contact the After-Sales Service.
3. The appliance is too noisy.
• Is the appliance perfectly horizontal?
• Is the appliance in contact with other furniture or objects
that may cause vibrations?
• Has the packaging been removed from under the
appliance?
Note:
Gurgling noises from the refrigerating circuit after the
compressor cuts out are perfectly normal.
4. All LEDs are o and the product is not working.
• Is there a power failure?
• Is the plug properly inserted in the socket?
• Is the electric cable intact?
5. All LEDs are o and the product is working.
• Contact the After-Sales Service.
6. The compressor runs continuously.
• Have hot foods been put in the appliance?
INSTRUCTIONS FOR USE
4
• Has the appliance lid been left open for a long time?
• Is the appliance placed in a very warm room or near heat
sources?
• Has the fast freeze function been activated? (The green
LEDs ash alternatively)
7. Too much ice on the upper edge.
• Are the defrost water drainage plugs correctly
positioned?
• Is the appliance lid properly closed?
• Is the appliance lid seal damaged or deformed? (See
chapter “Installation”)
• Have the 4 protection pieces been removed? (See
chapter “Installation”)
8. Formation of condensate on the external walls of
the appliance.
• It is normal for condensation to form under certain
atmospheric conditions (humidity above 85%) or if the
appliance is located in a damp or poorly ventilated room.
The performance of the appliance is in no way aected.
9. The layer of ice on the internal walls of the
appliance is not uniform.
• This phenomenon is quite normal.
AFTER‑SALES SERVICE
Before contacting After‑Sales Service:
1. See if you can solve the problem yourself.
2. Switch the appliance on again to see if the problem
has been solved. If it has not, disconnect the appliance
from the power supply and wait for about an hour before
switching on again.
3. If the problem persists after this course of action,
contact After-Sales Service.
Specify:
• the nature of the fault,
• the model,
• the service number (the number after the word
SERVICE on the rating plate on the rear of the
appliance)
• your full address,
• your telephone number and area code.
400011234466
ELECTRICAL CONNECTION FOR GREAT BRITAIN AND
IRELAND ONLY
Warning – this appliance must be earthed.
Fuse replacement
If the mains lead of this appliance is tted with a BS 1363A
13amp fused plug, to change a fuse in this type of plug use
an A.S.T.A. approved fuse to BS 1362 type and proceed
as follows:
1. Remove the fuse cover (A) and fuse (B).
2. Fit replacement 13A fuse into fuse cover.
3. Ret both into plug.
Important:
The fuse cover must be retted when changing a fuse and
if the fuse cover is lost the plug must not be used until a
correct replacement is tted.
Correct replacement are identied by the colour insert or
the colour embossed in words on the base of the plug.
Replacement fuse covers are available from your local
electrical store.
For the Republic of Ireland only
The information given in respect of Great Britain will
frequently apply, but a third type of plug and socket is also
used, the 2-pin, side earth type.
Socket outlet / plug (valid for both countries)
If the tted plug is not suitable for your socket outlet, please
contact After-sales Service for further instruction.
Please do not attempt to change plug yourself. This
procedure needs to be carried out by a qualied technician
in compliance with the manufactures instructions and
current standard safety regulations.