Table of Contents
- LTE4506-M606
- User’s Guide
- Technical Reference
Zyxel LTE4506-M606 User Manual
Displayed below is the user manual for LTE4506-M606 by Zyxel which is a product in the Wireless Routers category. This manual has pages.
Related Manuals
Default Login Details
User’s Guide
LTE4506-M606
4G LTE-A HomeSpot
Copyright © 2017 Zyxel Communications Corporation
LAN IP Address http://192.168.1.1
User Name admin
Password 1234
Version 1.10 Edition 2, 02/2017
LTE4506 User’s Guide
2
IMPORTANT!
READ CAREFULLY BEFORE USE.
KEEP THIS GUIDE FOR FUTURE REFERENCE.
This is a User’s Guide for a system managing a series of products. Not all products support all features.
Menushots and graphics in this book may differ slightly from what you see due to differences in release
versions or your computer operating system. Every effort has been made to ensure that the information
in this manual is accurate.
Related Documentation
• Quick Start Guide
The Quick Start Guide shows how to connect the managed device.
• More Information
Go to support.zyxel.com to find other information on the LTE4506.
Contents Overview
LTE4506 User’s Guide
3
Contents Overview
User’s Guide ....................................................................................................................................... 7
Introduction ............................................................................................................................................. 8
The Web Configurator ......................................................................................................................... 12
Technical Reference ....................................................................................................................... 19
Home ..................................................................................................................................................... 20
Internet ................................................................................................................................................... 25
Wi-Fi ........................................................................................................................................................ 32
Router ..................................................................................................................................................... 50
Applications .......................................................................................................................................... 59
System .................................................................................................................................................... 65
Troubleshooting .................................................................................................................................... 75
Table of Contents
LTE4506 User’s Guide
4
Table of Contents
Contents Overview ............................................................................................................................ 3
Table of Contents................................................................................................................................ 4
Part I: User’s Guide............................................................................................7
Chapter 1
Introduction ......................................................................................................................................... 8
1.1 Overview .......................................................................................................................................... 8
1.2 Ways to Manage the LTE4506 ......................................................................................................... 8
1.3 Good Habits for Managing the LTE4506 ........................................................................................ 9
1.4 Hardware Connections ................................................................................................................... 9
1.5 Turn on/off the LTE4506 .................................................................................................................... 9
1.6 LED Display ........................................................................................................................................ 9
1.7 One-touch Wi-Fi Sharing ............................................................................................................... 10
1.8 Resetting the LTE4506 ..................................................................................................................... 11
1.8.1 How to Use the Physical Reset Button ................................................................................ 11
Chapter 2
The Web Configurator....................................................................................................................... 12
2.1 Overview ......................................................................................................................................... 12
2.2 Login Accounts ............................................................................................................................... 12
2.3 Access .............................................................................................................................................. 12
2.4 Navigating the Web Configurator ............................................................................................... 13
2.4.1 Title Bar ................................................................................................................................... 14
2.4.2 Navigation Panel .................................................................................................................. 15
Part II: Technical Reference...........................................................................19
Chapter 3
Home.................................................................................................................................................. 20
3.1 Overview ......................................................................................................................................... 20
3.2 Home ............................................................................................................................................... 20
3.3 Setup Wizard ................................................................................................................................... 21
3.3.1 Internet ................................................................................................................................... 21
3.3.2 Wi-Fi ......................................................................................................................................... 22
Table of Contents
LTE4506 User’s Guide
5
Chapter 4
Internet............................................................................................................................................... 25
4.1 Overview ......................................................................................................................................... 25
4.1.1 What You Can Do in this Chapter ....................................................................................... 25
4.2 Internet Status Screen .................................................................................................................... 26
4.3 PIN Settings Screen ......................................................................................................................... 27
4.4 APN Configuration Screen ............................................................................................................ 28
4.5 Network Selection Screen ............................................................................................................. 29
4.6 Data Usage/Statistic Screen ......................................................................................................... 29
Chapter 5
Wi-Fi.................................................................................................................................................... 32
5.1 Overview ......................................................................................................................................... 32
5.1.1 What You Can Do in this Chapter ....................................................................................... 32
5.1.2 What You Need to Know ..................................................................................................... 33
5.2 Wi-Fi Status Screen .......................................................................................................................... 33
5.3 Wi-Fi Settings Screen ...................................................................................................................... 34
5.4 MAC Filter Screen .......................................................................................................................... 36
5.5 WPS Screen ..................................................................................................................................... 38
5.6 Technical Reference ...................................................................................................................... 39
5.6.1 Wireless Network Overview .................................................................................................. 39
5.6.2 Additional Wireless Terms ..................................................................................................... 40
5.6.3 Wireless Security Overview ................................................................................................... 40
5.6.4 Signal Problems ..................................................................................................................... 43
5.6.5 WiFi Protected Setup (WPS) ................................................................................................. 43
Chapter 6
Router................................................................................................................................................. 50
6.1 Overview ......................................................................................................................................... 50
6.1.1 What You Can Do in this Chapter ....................................................................................... 50
6.2 LAN IP Screen ................................................................................................................................. 50
6.3 DHCP Server Screen ....................................................................................................................... 51
6.4 DNS Settings Screen ....................................................................................................................... 53
6.5 Connected Devices Screen .......................................................................................................... 53
6.6 IPv4/Port Filter Screen ..................................................................................................................... 54
6.7 IPv6/Port Filter Screen ..................................................................................................................... 55
6.8 URL Filter Screen .............................................................................................................................. 56
6.9 IP/Port Forwarding Screen ............................................................................................................. 57
Chapter 7
Applications ...................................................................................................................................... 59
7.1 Overview ......................................................................................................................................... 59
7.1.1 What You Can Do in this Chapter ....................................................................................... 59
Table of Contents
LTE4506 User’s Guide
6
7.2 Contact List Screen ........................................................................................................................ 59
7.3 SIM Contacts Screen ...................................................................................................................... 60
7.4 Contacts Settings Screen .............................................................................................................. 61
7.5 New SMS Screen ............................................................................................................................ 61
7.6 Inbox Screen ................................................................................................................................... 62
7.7 Outbox Screen ................................................................................................................................ 63
7.8 Draft Screen .................................................................................................................................... 63
7.9 SIM SMS Screen ............................................................................................................................... 64
Chapter 8
System................................................................................................................................................ 65
8.1 Overview ......................................................................................................................................... 65
8.1.1 What You Can Do in this Chapter ....................................................................................... 65
8.2 System Information Screen ............................................................................................................ 65
8.3 User Account Screen ..................................................................................................................... 67
8.4 Settings Profile Screen .................................................................................................................... 68
8.4.1 Reset Settings ......................................................................................................................... 69
8.4.2 Save Current Settings ........................................................................................................... 69
8.4.3 Import & Export Settings Profile ............................................................................................ 70
8.5 Firmware Upgrade Screen ............................................................................................................ 70
8.6 Time Settings Screen ...................................................................................................................... 71
8.7 System Log Screen ......................................................................................................................... 73
Chapter 9
Troubleshooting................................................................................................................................. 75
9.1 Overview ......................................................................................................................................... 75
9.2 Power, and Hardware Installation ................................................................................................ 75
9.3 LTE4506 Access and Login ............................................................................................................. 75
9.4 Internet Access ............................................................................................................................... 76
9.5 Wireless Connections ..................................................................................................................... 77
9.6 Getting More Troubleshooting Help ............................................................................................. 78
Appendix A Customer Support........................................................................................................ 79
Appendix B Common Services........................................................................................................ 85
Appendix C Legal Information ........................................................................................................ 88
Index .................................................................................................................................................. 96
7
PART I
User’s Guide
LTE4506 User’s Guide
8
CHAPTER 1
Introduction
1.1 Overview
This chapter introduces the main features and applications of the LTE4506.
The LTE4506 is a 4G+ home-spot wireless router, which can connect to a mobile network and the Internet
through a wireless WAN connection and provide easy network access to mobile users without additional
wiring. You can set up a wireless network with other IEEE 802.11b/g/n compatible devices.
A range of services such as a firewall are also available for secure Internet computing.
Your LTE4506 is easy to install, configure and use. The embedded Web-based configurator enables
simple, straightforward management and maintenance. See the Quick Start Guide for how to make
hardware connections.
1.2 Ways to Manage the LTE4506
You can use the following way to manage the LTE4506.
Web Configurator
The Web Configurator allows easy LTE4506 setup and management using an Internet browser. This User’s
Guide provides information about the Web Configurator.
LTE4506
Chapter 1 Introduction
LTE4506 User’s Guide
9
1.3 Good Habits for Managing the LTE4506
Do the following things regularly to make the LTE4506 more secure and to manage it more effectively.
• Change the password often. Use a password that’s not easy to guess and that consists of different
types of characters, such as numbers and letters.
• Write down the password and put it in a safe place.
• Back up the configuration (and make sure you know how to restore it). Restoring an earlier working
configuration may be useful if the device becomes unstable or even crashes. If you forget your
password, you will have to reset the LTE4506 to its factory default settings. If you backed up an earlier
configuration file, you won’t have to totally re-configure the LTE4506; you can simply restore your last
configuration.
1.4 Hardware Connections
See your Quick Start Guide for information on making hardware connections. You need to insert a SIM
card to the SIM card slot at the bottom of the LTE4506 before you can use it.
1.5 Turn on/off the LTE4506
To turn on the device, press the power button and hold until any of the LED lights turns on
To turn off the device, press the power button and hold until all the LED lights are off.
Figure 1 LTE4506 Power Button
1.6 LED Display
You can check the LED lights to see the 2G/3G/4G connection status, signal strength, and the wireless
connection status.
Chapter 1 Introduction
LTE4506 User’s Guide
10
Figure 2 LTE4506 LEDs
The following table describes the LED lights.
1.7 One-touch Wi-Fi Sharing
Press the One-Touch button on the top of the LTE4506 to turn on the Wi-Fi sharing function. Users can
easily connect to the LTE4506.
Table 1 LTE4506 LEDs
ICONS DESCRIPTION
The power signal and quality of the mobile network to which the LTE4506 is connecting.
Flashing red: the power is on, but there is no LTS/3G signal received.
Solid red: there is a weak signal quality.
Solid orange: there is a medium signal quality.
Solid green: there is a good signal quality.
The Internet connection status and SMS status.
Solid: the Internet access is available and there is no new SMS.
Flashing fast: the Internet access is available and there is a new SMS.
Flashing slow: the Internet access is not available and there is a new SMS.
Off: the Internet access is not available and there is no new SMS.
The Wi-Fi/WPS status.
Solid green: the Wi-Fi AP is on.
Flashing green fast: Data is being transmitted and received.
Flashing green slow: the WPS is on.
Chapter 1 Introduction
LTE4506 User’s Guide
11
Figure 3 The Wi-Fi Sharing Button
1.8 Resetting the LTE4506
If you forget your password or IP address, or you cannot access the Web Configurator, you will need to
use the physical Reset button to reload the factory-default configuration file. This means that you will
lose all configurations that you had previously saved, the password will be reset to 1234 and the IP
address will be reset to 192.168.1.1.
1.8.1 How to Use the Physical Reset Button
1Make sure the LTE4506 is turned on.
2Press the Reset button at the bottom of the LTE4506 until it reboots and set it back to the factory-default
configurations.
LTE4506 User’s Guide
12
CHAPTER 2
The Web Configurator
2.1 Overview
The LTE4506 Web Configurator allows easy management using an Internet browser.
In order to use the Web Configurator, you must:
• Use Internet Explorer 8.0 and later versions, Mozilla Firefox 43.0 and 44.0 versions, Safari 7.0 and 8.0
versions, or Google Chrome 40.0 and 41.0 versions.
• Allow pop-up windows.
• Enable JavaScript (enabled by default).
• Enable cookies.
2.2 Login Accounts
There is one system account that you can use to log in to the LTE4506: “admin”. The admin account
allows you full access to all system configurations. The default admin user name is “admin” and
password is “1234”.
2.3 Access
1Make sure your LTE4506 hardware is properly connected. See the Quick Start Guide.
2Launch your web browser.
3Type "http://192.168.1.1" as the website address. The Login screen appears.
Your computer must be in the same subnet in order to access this website address.
Chapter 2 The Web Configurator
LTE4506 User’s Guide
13
4Enter the user name (default: “admin” ) and password (default: “1234” ). See Section 2.2 on page 12 for
more information about login accounts. Click Login.
5The following screen displays if you have not yet changed your password. Enter a new password, retype
it to confirm and click OK.
6The Home screen appears.
2.4 Navigating the Web Configurator
The following summarizes how to navigate the web configurator from the Home screen.
Chapter 2 The Web Configurator
LTE4506 User’s Guide
14
Figure 4 The Web Configurator’s Main Screen
The Web Configurator’s main screen is divided into these parts:
•A - Title Bar
•B - Navigation Panel_Sub-Menus
•C - Main Window
•D - Navigation Panel_Main Menus
2.4.1 Title Bar
The title bar provides some useful links that always appear over the screens below, regardless of how
deep into the Web Configurator you navigate.
Figure 5 Title Bar
The icons provide the following functions.
A
C
B
D
Table 2 Title Bar: Web Configurator Icons
LABEL DESCRIPTION
SIM This shows whether a SIM card is inserted in the LTE4506.
The icon shows if there is no SIM card inserted.
Signal Strength This shows the current signal strength to the mobile network.
The icon is grayed out if the mobile data connection is not up.
Chapter 2 The Web Configurator
LTE4506 User’s Guide
15
2.4.2 Navigation Panel
Use the menu items on the navigation panel to open screens to configure LTE4506 features. The
following sections introduce the LTE4506’s navigation panel menus and their screens.
Figure 6 Navigation Panel
Home Menu
The Home menu screens display status and statistics information.
Internet Menu
Service Provider This shows the name of the service provider for the mobile network to which the LTE4506 is
connected.
This shows Searching... if the LTE4506 is not connected to a mobile network yet.
Roaming This shows whether the LTE4506 is connected to another service provider’s mobile network
using roaming.
The icon is grayed out if roaming is disabled on the LTE4506.
Internet This shows whether the LTE4506 has an Internet connection.
The icon shows if the LTE4506 in not connected to the Internet.
Wi-Fi This shows whether the LTE4506’s Wi-Fi network is active and the number of the connected
wireless clients.
Language Choose your language from the drop-down list on the upper right corner of the title bar.
Logout Click this to log out of the Web Configurator.
Table 2 Title Bar: Web Configurator Icons (continued)
LABEL DESCRIPTION
Table 3 Home Menu Screens Summary
LABEL DESCRIPTION
Home Display connection mode, wireless LAN information and the LTE4506’s
traffic statistics.
Use this screen to access the wizard.
Table 4 Internet Menu Screens Summary
LABEL DESCRIPTION
Internet
Internet Status Configure the WAN settings on the LTE4506 for Internet access.
PIN Settings Configure the PIN code when PIN code authentication is enabled.
Change the PIN code for the inserted SIM card.
APN
Configuration Configure user-defined connection profiles.
Chapter 2 The Web Configurator
LTE4506 User’s Guide
16
WiFi Menu
Network
Selection Display available Public Land Mobile Networks and select a preferred
network for roaming.
Data Usage/
Statistic Specify limiting the amount of the package data and view the LTE4506’s
traffic statistics.
Table 5 WiFi Menu Screens Summary
LABEL DESCRIPTION
WiFi
Wi-Fi Status Display information about the 2.4GHz/5GHz wireless LAN.
Wi-Fi Settings Enable the wireless LAN and configure the basic wireless settings.
MAC Filter Allow or deny wireless clients based on their MAC addresses from
connecting to the LTE4506.
WPS Activate WPS.
Table 4 Internet Menu Screens Summary (continued)
LABEL DESCRIPTION
Chapter 2 The Web Configurator
LTE4506 User’s Guide
17
Router Menu
Applications Menu
System Menu
Table 6 Router Menu Screens Summary
LABEL DESCRIPTION
LAN IP Configure the management IP address for the LTE4506 LAN interface.
DHCP Server Enable the DHCP server on the LTE4506.
Configure static DHCP entries.
DNS Settings Automatically configured DNS server from mobile network or manually
configure the first and second DNS server IP.
Connected
Devices
View current clients information of network clients connected to the
LTE4506.
Firewall
IPv4/Port Filter Configure IPv4/Port filtering rules.
IPv6/Port Filter Configure IPv6/Port filtering rules.
URL Filter Configure URL filtering rules.
IP/Port
Forwarding Configure port forwarding rules.
Table 7 Applications Menu Screens Summary
LABEL DESCRIPTION
Contacts Configure the contact list saved on the LTE4506.
SIM Contacts Display the contact list saved on the SIM card.
Contacts
Settings Import or export your contacts.
Short Message
New SMS Send new SMS messages.
Inbox Display messages received on the LTE4506.
Outbox Display messages sent from the LTE4506.
Draft Display messages not yet sent from the LTE4506.
SIM SMS Display messages received on the SIM card.
Table 8 System Menu Screens Summary
LABEL DESCRIPTION
System
System
Information Display the LTE4506’s basic information and restart the LTE4506.
User Account Change administrative settings and the password of your LTE4506.
Settings Profile Backup and restore device configurations, or reset your device settings
back to the factory default.
Firmware
Upgrade Upload new firmware to the LTE4506.
Chapter 2 The Web Configurator
LTE4506 User’s Guide
18
Time Settings Change the LTE4506’s time and date.
Select your time zone and configure daylight saving time.
System Log Configure to where the LTE4506 is to send logs.
View the logged messages.
Table 8 System Menu Screens Summary (continued)
LABEL DESCRIPTION
19
PART II
Technical Reference
LTE4506 User’s Guide
20
CHAPTER 3
Home
3.1 Overview
Use the Home screen to check status information about the LTE4506. Use the Wizard screens to configure
the LTE4506’s basic Internet access and wireless settings.
3.2 Home
This screen is the first thing you see when you log into the LTE4506. It also appears every time you click
the Home icon in the navigation panel. The Home screen displays the LTE4506’s connection mode,
wireless LAN information and traffic statistics.
Figure 7 Home
The following table describes the labels in this screen.
Table 9 Home
LABEL DESCRIPTION
Manager
Connection
Mode This field displays the connected mode of the LTE4506. Select Always to connect to the
mobile network automatically if there is an available mobile network. Select On Demand to
connect to the mobile network automatically only when a connected client wants to
access the Internet. Otherwise, select Manual.
Setup Wizard Click this button to set up the Internet and Wi-Fi.
Wi-Fi 2.4G
SSID This displays a descriptive name used to identify the LTE4506 in the 2.4GHz wireless LAN.
Encryption This displays the level of wireless security the LTE4506 is using.
Chapter 3 Home
LTE4506 User’s Guide
21
3.3 Setup Wizard
Click Home > Setup Wizard to open the wizard screen.
3.3.1 Internet
Select the Auto option if you did not configure the connection profile. Click Next to continue.
Figure 8 Setup Wizard > Set Up Internet: APN Profile
Select the Internet connection mode of the LTE4506. Click Next to continue.
Clients This field displays the total number of the associated stations.
Wi-Fi 5G
SSID This displays a descriptive name used to identify the LTE4506 in the 5GHz wireless LAN.
Encryption This displays the level of wireless security the LTE4506 is using.
Clients This field displays the total number of the associated stations.
Internet If you have inserted a valid SIM card, this field displays the total amount of data in kilobytes
that has been transmitted and received on the WAN interface since the LTE4506 last
restarted.
Table 9 Home (continued)
LABEL DESCRIPTION
Chapter 3 Home
LTE4506 User’s Guide
22
Figure 9 Setup Wizard > Set Up Internet: Connection Mode
Specify limiting the amount of the package data and reminding the percentage of the package data
usage. Click Next to configure the Wi-Fi settings.
Figure 10 Setup Wizard > Set Up Internet: Package Data Limit
3.3.2 Wi-Fi
If you have not enabled the Wi-Fi 1 network, this screen shows the Wi-Fi 1 and Wi-Fi 2 network status. Click
the button of a Wi-Fi network to enable it. Click Next to go to the next step.
Chapter 3 Home
LTE4506 User’s Guide
23
Figure 11 Wizard > Set Up Wi-Fi (if Wi-Fi 1 is not enabled)
If you have enabled the Wi-Fi 1 network, this screen shows the default Wi-Fi key and SSID for the LTE4506’s
wireless network. If you set up a new key and SSID, the wireless clients will lose their wireless connection
and need to use new wireless settings. Click Next to go to the next step.
Figure 12 Wizard > Set Up Wi-Fi (after two SSID networks have been enabled)
Click Apply to save your changes. The LTE4506 will restart.
Chapter 3 Home
LTE4506 User’s Guide
24
Table 10 Apply Settings
LTE4506 User’s Guide
25
CHAPTER 4
Internet
4.1 Overview
This chapter discusses the LTE4506’s Internet screens. Use these screens to configure your LTE4506 for
Internet access.
A WAN (Wide Area Network) connection is an outside connection to another network or the Internet. It
connects your private networks, such as a LAN (Local Area Network) and other networks, so that a
computer in one location can communicate with computers in other locations.
Figure 13 LAN/Wireless LAN and Wireless WAN
4.1.1 What You Can Do in this Chapter
• Use the Internet Status screen to configure the WAN settings on the LTE4506 for Internet access
(Section 4.2 on page 26).
• Use the PIN Settings screen to enable or disable PIN code authentication (Section 4.3 on page 27).
• Use the APN Configuration screen to configure user-defined connection profiles (Section 4.4 on page
28).
• Use the Network Selection screen to display available Public Land Mobile Networks and select a
preferred network for roaming (Section 4.5 on page 29).
• Use the Data Usage/Statistic screen to specify limiting the amount of the package data and view the
LTE4506’s traffic statistics (Section 4.6 on page 29).
LTE4506
LAN
Chapter 4 Internet
LTE4506 User’s Guide
26
4.2 Internet Status Screen
Use this screen to change your LTE4506’s Internet access settings. Click Internet > Internet Status. The
screen appears as shown next.
Figure 14 Internet > Internet Status
The following table describes the labels in this screen.
Table 11 Internet > Internet Status
LABEL DESCRIPTION
Internet Status
Network
Provider
This shows the name of the service provider for the mobile network to which the LTE4506 is
connected.
Internet Status This shows the mobile data connection status.
IP Address (IPv4) This field displays the current IPv4 address assigned to the WAN interface.
IP Address (IPv6) This field displays the current IPv6 address assigned to the WAN interface.
Signal Level This shows the current signal strength to the mobile network in dBm.
Network Type This shows the type of the mobile network (such as LTE, UMTS, GSM, HSPA+, etc.) to which the
LTE4506 is connecting.
Connection
Time
This field displays how long you connect to the Internet through IPv4.
Internet Settings
Allow Data
Roaming
Select this check box to enable data roaming on the LTE4506.
4G roaming is to use your mobile device in an area which is not covered by your service
provider. Enable roaming to ensure that your LTE4506 is kept connected to the Internet when
you are traveling outside the geographical coverage area of the network to which you are
registered.
Chapter 4 Internet
LTE4506 User’s Guide
27
4.3 PIN Settings Screen
Use this screen to turn on or turn off PIN code authentication on the inserted SIM card. Click Internet >
PIN Settings. The screen appears as shown next.
Figure 15 Internet > PIN Settings
The following table describes the labels in this screen.
Cellular Network
Mode
Select the type of the network (4G Mode, 3G Mode, or 2G Mode) to which you want the LTE4506
to connect and click Apply to save your settings.
Otherwise, select Auto to have the LTE4506 connect to an available network using the default
settings on the SIM card. If the currently registered mobile network is not available or the mobile
network’s signal strength is too low, the LTE4506 switches to another available mobile network.
Internet
Connection
Method
Select Always to connect to the mobile network automatically if there is an available mobile
network. Select On Demand to connect to the mobile network automatically only when a
connected client wants to access the Internet. Otherwise, select Manual.
Disconnect in Specifies the period of time the user can be idle before he/she is disconnected.
Apply Click Apply to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
Table 11 Internet > Internet Status (continued)
LABEL DESCRIPTION
Table 12 Internet > PIN Settings
LABEL DESCRIPTION
PIN Protection
Enable PIN
Protection
Click On to turn on PIN code authentication. Otherwise, click Off to turn off PIN code
authentication.
A PIN (Personal Identification Number) code is a key to a SIM card. Without the PIN code, you
cannot use the SIM card.
Change PIN Code
Chapter 4 Internet
LTE4506 User’s Guide
28
4.4 APN Configuration Screen
Use this screen to view or configure a connection profile. A connection profile defines the parameters
that you need to connect to a mobile network, such as the APN, user name and password. Click
Internet > APN Configuration. The screen appears as shown next.
Figure 16 Internet > APN Configuration
The following table describes the labels in this screen.
Current PIN Enter the default or existing PIN code for the inserted SIM card.
New PIN Configure a new PIN code for the SIM card. You can specify any four to eight digits to have a
new PIN code.
Confirm New
PIN
Enter the new PIN code again for confirmation.
Apply Click Apply to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
Table 12 Internet > PIN Settings
LABEL DESCRIPTION
Table 13 Internet > APN Configuration
LABEL DESCRIPTION
Select APN
Profile
Select Auto to reload the default profile. Otherwise, select Manual to configure a connection
profile.
APN This field displays the Access Point Name (APN) in the profile.
Enter the Access Point Name (APN) provided by your service provider. Connections with
different APNs may provide different services (such as Internet access or MMS (Multi-Media
Messaging Service)) and charging method.
You can enter up to 30 printable ASCII characters. Spaces are allowed.
Username This field displays the user name in the profile.
Type the user name (of up to 31 printable ASCII characters) given to you by your service
provider.
Chapter 4 Internet
LTE4506 User’s Guide
29
4.5 Network Selection Screen
This screen allows you to view available Public Land Mobile Networks (PLMNs) and select your preferred
network when the LTE4506 is outside the geographical coverage area of the network to which you are
registered and roaming is enabled.
Click Internet > Network Selection. The screen appears as shown next.
Figure 17 Internet > Network Selection
The following table describes the labels in this screen.
4.6 Data Usage/Statistic Screen
This screen allows you to configure limiting the amount of the package data and view the LTE4506’s
traffic statistics.
Click Internet > Data Usage/Statistic. The screen appears as shown next.
Password This field displays the password in the profile.
Type the password (of up to 31 printable ASCII characters) associated with the user name
above.
Apply Click Apply to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
Table 13 Internet > APN Configuration
LABEL DESCRIPTION
Table 14 Internet > Network Selection
LABEL DESCRIPTION
Select PLMN
Mode
Select Auto to have the LTE4506 automatically connect to the first available mobile network
using roaming when it is outside the coverage area of the original service provider’s network.
Select Manual to display the network list and manually select a preferred network.
Apply Click Apply to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
Chapter 4 Internet
LTE4506 User’s Guide
30
Figure 18 Internet > Data Usage/Statistic
The following table describes the labels in this screen.
Table 15 Internet > Data Usage/Statistic
LABEL DESCRIPTION
Package Data Limit Setting
Enable Data
Limit
Select the check box to enable data limits.
My Internet
package data
limit is
Specify the limiting the amount of the package data in this field.
Chapter 4 Internet
LTE4506 User’s Guide
31
Remind me
when data
usage is more
than
Specify the reminding percentage of the package data usage in this field.
Usage cycle
reset date
Specify the date that you want the LTE4506 to restart calculating the amount of the package
data per month.
Apply Click Apply to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
Reset Network Statistics
Reset all
statistics and
histories
Click Reset to remove all traffic statistics.
Current Connection Statistics
Data Flow This indicates the current traffic flow transmitting from/to the LTE4506.
Sent This indicates the number of transmitted packets on the LTE4506.
Received This indicates the number of received packets on the LTE4506.
Total Connection Statistics
Data Flow This indicates total traffic flows transmitting from/to the LTE4506.
Sent This indicates the number of transmitted packets on the LTE4506.
Received This indicates the number of received packets on the LTE4506.
Table 15 Internet > Data Usage/Statistic
LABEL DESCRIPTION
LTE4506 User’s Guide
32
CHAPTER 5
Wi-Fi
5.1 Overview
This chapter describes the LTE4506’s Wi-Fi screens. Use these screens to set up your LTE4506’s wireless LAN
connection.
5.1.1 What You Can Do in this Chapter
• Use the Wi-Fi Status screen to view information about the 2.4GHz/5GHz wireless LAN (Section 5.2 on
page 33).
• Use the Wi-Fi Settings screen to enable the wireless LAN, enter the SSID and select the wireless security
mode (Section 5.3 on page 34).
• Use the MAC Filter screen to deny wireless clients based on their MAC addresses from connecting to
the LTE4506 (Section 5.4 on page 36).
• Use the WPS screen to activate WPS via PBC or PIN configuration (Section 5.5 on page 38).
Chapter 5 Wi-Fi
LTE4506 User’s Guide
33
5.1.2 What You Need to Know
Wireless Basics
“Wireless” is essentially radio communication. In the same way that walkie-talkie radios send and
receive information over the airwaves, wireless networking devices exchange information with one
another. A wireless networking device is just like a radio that lets your computer exchange information
with radios attached to other computers. Like walkie-talkies, most wireless networking devices operate
at radio frequency bands that are open to the public and do not require a license to use. However,
wireless networking is different from that of most traditional radio communications in that there a
number of wireless networking standards available with different methods of data encryption.
Guest WLAN
Guest WLAN allows you to set up a wireless network where users can access to Internet via the LTE4506
(Z), but not other networks connected to the Z. In the following figure, a guest user can access the
Internet from the guest wireless network A via Z but not the home or company network N.
Note: The home or company network N and Guest WLAN network are independent networks.
Figure 19 Guest Wireless LAN Network
Finding Out More
See Section 5.6 on page 39 for advanced technical information on wireless networks.
5.2 Wi-Fi Status Screen
Use this screen to view information about the 2.4GHz/5GHz wireless LAN. Click Wi-Fi > Wi-Fi Status to
access this screen.
A
Z
N
Chapter 5 Wi-Fi
LTE4506 User’s Guide
34
Figure 20 Wi-Fi > Wi-Fi Status
The following table describes the labels in this screen.
5.3 Wi-Fi Settings Screen
Use this screen to enable the wireless LAN, enter the SSID and select the wireless security mode.
Note: If you are configuring the LTE4506 from a computer connected to the wireless LAN and
you change the LTE4506’s SSID, channel or security settings, you will lose your wireless
connection when you press Apply to confirm. You must then change the wireless
settings of your computer to match the LTE4506’s new settings.
To access this screen, click Wi-Fi > Wi-Fi Settings.
Table 16 Wi-Fi > Wi-Fi Status
LABEL DESCRIPTION
Wi-Fi Status
SSID 1/ SSID2 The SSID (Service Set IDentity) identifies the service set with which a wireless device is
associated. Wireless devices associating to the access point (AP) must have the same SSID.
This displays the basic wireless settings of SSID 1 and SSID 2.
SSID 1/ SSID2 This displays a descriptive name used to identify the LTE4506 in the 2.4GHz/5GHz wireless LAN.
Encryption This field displays the level of wireless security the LTE4506 is using.
MAC Address This field displays the 2.4GHz/5GHz wireless adapter MAC Address of your device.
Channel This field displays the channel number which you select manually.
Chapter 5 Wi-Fi
LTE4506 User’s Guide
35
Figure 21 Wi-Fi > Wi-Fi Settings
The following table describes the labels in this screen.
Table 17 Wi-Fi > Wi-Fi Settings
LABEL DESCRIPTION
SSID 1/ SSID 2 Select SSID 1 (or SSID 2) to configure the basic wireless settings.
Enable SSID 1 (or
SSID 2)
Select the check box to enable the wireless LAN of the LTE4506.
Wireless Band Select the frequency band to set whether you want to apply the wireless and security settings to
the default 2.4GHz or 5GHz wireless LAN.
Network Name
(SSID)
The SSID (Service Set IDentity) identifies the service set with which a wireless device is associated.
Wireless devices associating to the access point (AP) must have the same SSID.
Enter a descriptive name (up to 32 English keyboard characters) for the wireless LAN.
Chapter 5 Wi-Fi
LTE4506 User’s Guide
36
5.4 MAC Filter Screen
This screen allows you to configure the LTE4506 to exclude specific devices from accessing the LTE4506
(Deny). Every Ethernet device has a unique MAC (Media Access Control) address. The MAC address is
assigned at the factory and consists of six pairs of hexadecimal characters, for example,
00:A0:C5:00:00:02. You need to know the MAC addresses of the devices to configure this screen.
Encryption
Mode
Select WPA, WPA2, or WPA/WPA2 to add security on this wireless network. The wireless clients
which want to associate to this network must have same wireless security settings as the LTE4506.
When you select to use a security, additional options appears in this screen.
Select WPA/WPA2 to allow wireless devices that support either WPA or WPA2 to connect to your
LTE4506’s wireless network.
Select WPA to allow only wireless devices that support WPA to connect to your LTE4506’s wireless
network.
Select WPA2 to allow only wireless devices that support WPA2 to connect to your LTE4506’s
wireless network.
Or you can select NO ENCRYPTION to allow any client to associate this network without any data
encryption or authentication.
SSID Visibility Select Disable to hide the SSID in the outgoing beacon frame so a station cannot obtain the SSID
through scanning using a site survey tool. Otherwise, select Enable.
Wi-Fi Network
Mode
If you set Wireless Band to 2.4GHz, you can use the 802.11 mode from the following:
•802.11 bgn: allows IEEE802.11b, IEEE802.11g and IEEE802.11n compliant WLAN devices to
associate with the LTE4506. The transmission rate of your LTE4506 might be reduced.
If you set Wireless Band to 5GHz, you can use the 802.11 mode from the following:
•802.11a/n/ac: allows IEEE802.11n, IEEE802.11a and IEEE 802.11c compliant WLAN devices to
associate with the LTE4506.
Channel Width This field displays the wireless channel width used by LTE4506.
A standard 20MHz channel offers transfer speeds of up to 144Mbps (2.4GHz) or 217Mbps (5GHZ)
whereas a 40MHz channel uses two standard channels and offers speeds of up to 300Mbps
(2.4GHz) or 450Mbps (5GHZ).
Channel Set the channel depending on your particular region.
Select a channel or use Auto Channel to have the LTE4506 automatically determine a channel
to use. If you are having problems with wireless interference, changing the channel may help.
Try to use a channel that is as many channels away from any channels used by neighboring APs
as possible. The channel number which the LTE4506 is currently using then displays next to this
field.
The following fields are available if you set Encryption Mode to WPA, WPA2, or WPA/WPA2.
Encryption Type Select the encryption type (AES-CCMP or AUTO) for data encryption.
Select AES-CCMP if your wireless clients can all use AES-CCMP.
Select AUTO (TKIP+AES-CCMP) to allow the wireless clients to use either TKIP or AES-CCMP.
Encryption Key Select ASCII in order to enter ASCII characters as WEP key. Select HEX in order to enter
hexadecimal characters as a WEP key.
Apply Click Apply to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
Table 17 Wi-Fi > Wi-Fi Settings
LABEL DESCRIPTION
Chapter 5 Wi-Fi
LTE4506 User’s Guide
37
Use this screen to view your LTE4506’s MAC filter settings and add new MAC filter rules. Click Wi-Fi > MAC
Filter. The screen appears as shown.
Figure 22 Wi-Fi > MAC Filter
The following table describes the labels in this screen.
Table 18 Wi-Fi > MAC Filter
LABEL DESCRIPTION
SSID 1/ SSID 2 Select SSID 1 (or SSID 2) to configure the MAC filtering rules.
Enable MAC
Filter of SSID 1
(or SSID 2)
Select Enable MAC Filter of SSID 1 (or SSID 2) to prohibit devices with the MAC addresses you
configured.
Blacklist This field displays how many entries you display on this page.
Add New Click Add New to create a new entry.
Delete All Click Delete All to remove all entries.
This field displays the index number of the MAC address entry.
MAC Address This field displays the MAC addresses of the wireless devices that are allowed or denied access
to the LTE4506.
Click Add New or Edit to enter or change the MAC address of the wireless devices that are
allowed or denied access to the LTE4506 in this field. Enter the MAC addresses in a valid MAC
address format, that is, six hexadecimal character pairs, for example, 12:34:56:78:9a:bc.
Description This field displays the name of the MAC address entry.
Click Add New or Edit to enter a descriptive name to identify the MAC address entry. You can
enter up to 20 printable ASCII characters. Spaces are allowed.
Action Click Edit to go to the screen where you can edit the rule.
Click Delete to remove the MAC address entry.
Apply Click Apply to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
Chapter 5 Wi-Fi
LTE4506 User’s Guide
38
5.5 WPS Screen
Use this screen to configure Wi-Fi Protected Setup (WPS) on your LTE4506.
WPS allows you to quickly set up a wireless network with strong security, without having to configure
security settings manually. Set up each WPS connection between two devices. Both devices must
support WPS. See Section 5.6.5.3 on page 45 for more information about WPS.
Note: To use the WPS feature, make sure you have wireless enabled in the Wi-Fi > Wi-Fi
Settings screen.
Note: If you want to use the WPS feature set the security type to WPA or None.
Click Wi-Fi > WPS. The following screen displays.
Figure 23 Wi-Fi > WPS
The following table describes the labels in this screen.
Table 19 Wi-Fi > WPS
LABEL DESCRIPTION
Select WPS
Interface
Select SSID 1 (or SSID 2) to configure WPS.
Select WPS
Method
• Select PBC to set up a WPS wireless network using Push Button Configuration (PBC).
If you select PBC, click Activate to add another WPS-enabled wireless device (within wireless
range of the LTE4506) to your wireless network. This button may either be a physical button on
the outside of device, or a menu button similar to the Connect button on this screen.
Note: You must press the other wireless device’s WPS button within two minutes of
pressing this button.
• Select PIN to set up a WPS wireless network by entering the PIN of the client into the LTE4506.
WPS PIN This field is available only when you set Select WPS Method to PIN.
Select this option and enter the PIN of the device that you are setting up a WPS connection with
and click Apply to authenticate and add the wireless device to your wireless network.
You can find the PIN either on the outside of the device, or by checking the device’s settings.
Note: You must also activate WPS on that device within two minutes to have it
present its PIN to the LTE4506.
Chapter 5 Wi-Fi
LTE4506 User’s Guide
39
5.6 Technical Reference
This section discusses wireless LANs in depth.
5.6.1 Wireless Network Overview
Wireless networks consist of wireless clients, access points and bridges.
• A wireless client is a radio connected to a user’s computer.
• An access point is a radio with a wired connection to a network, which can connect with numerous
wireless clients and let them access the network.
• A bridge is a radio that relays communications between access points and wireless clients, extending
a network’s range.
Traditionally, a wireless network operates in one of two ways.
• An “infrastructure” type of network has one or more access points and one or more wireless clients.
The wireless clients connect to the access points.
• An “ad-hoc” type of network is one in which there is no access point. Wireless clients connect to one
another in order to exchange information.
The following figure provides an example of a wireless network.
Figure 24 Example of a Wireless Network
The wireless network is the part in the blue circle. In this wireless network, devices A and B use the access
point (AP) to interact with the other devices (such as the printer) or with the Internet. Your LTE4506 is the
AP.
Every wireless network must follow these basic guidelines.
• Every device in the same wireless network must use the same SSID.
The SSID is the name of the wireless network. It stands for Service Set IDentifier.
Chapter 5 Wi-Fi
LTE4506 User’s Guide
40
• If two wireless networks overlap, they should use a different channel.
Like radio stations or television channels, each wireless network uses a specific channel, or frequency,
to send and receive information.
• Every device in the same wireless network must use security compatible with the AP.
Security stops unauthorized devices from using the wireless network. It can also protect the
information that is sent in the wireless network.
Radio Channels
In the radio spectrum, there are certain frequency bands allocated for unlicensed, civilian use. For the
purposes of wireless networking, these bands are divided into numerous channels. This allows a variety of
networks to exist in the same place without interfering with one another. When you create a network,
you must select a channel to use.
Since the available unlicensed spectrum varies from one country to another, the number of available
channels also varies.
5.6.2 Additional Wireless Terms
The following table describes some wireless network terms and acronyms used in the LTE4506’s Web
Configurator.
5.6.3 Wireless Security Overview
By their nature, radio communications are simple to intercept. For wireless data networks, this means
that anyone within range of a wireless network without security can not only read the data passing over
the airwaves, but also join the network. Once an unauthorized person has access to the network, he or
she can steal information or introduce malware (malicious software) intended to compromise the
network. For these reasons, a variety of security systems have been developed to ensure that only
authorized people can use a wireless data network, or understand the data carried on it.
These security standards do two things. First, they authenticate. This means that only people presenting
the right credentials (often a username and password, or a “key” phrase) can access the network.
Second, they encrypt. This means that the information sent over the air is encoded. Only people with
Table 20 Additional Wireless Terms
TERM DESCRIPTION
RTS/CTS Threshold In a wireless network which covers a large area, wireless devices are sometimes not
aware of each other’s presence. This may cause them to send information to the AP at
the same time and result in information colliding and not getting through.
By setting this value lower than the default value, the wireless devices must sometimes get
permission to send information to the LTE4506. The lower the value, the more often the
devices must get permission.
If this value is greater than the fragmentation threshold value (see below), then wireless
devices never have to get permission to send information to the LTE4506.
Preamble A preamble affects the timing in your wireless network. There are two preamble modes:
long and short. If a device uses a different preamble mode than the LTE4506 does, it
cannot communicate with the LTE4506.
Authentication The process of verifying whether a wireless device is allowed to use the wireless network.
Fragmentation
Threshold
A small fragmentation threshold is recommended for busy networks, while a larger
threshold provides faster performance if the network is not very busy.
Chapter 5 Wi-Fi
LTE4506 User’s Guide
41
the code key can understand the information, and only people who have been authenticated are
given the code key.
These security standards vary in effectiveness. Some can be broken, such as the old Wired Equivalent
Protocol (WEP). Using WEP is better than using no security at all, but it will not keep a determined
attacker out. Other security standards are secure in themselves but can be broken if a user does not use
them properly. For example, the WPA-PSK security standard is very secure if you use a long key which is
difficult for an attacker’s software to guess - for example, a twenty-letter long string of apparently
random numbers and letters - but it is not very secure if you use a short key which is very easy to guess -
for example, a three-letter word from the dictionary.
Because of the damage that can be done by a malicious attacker, it’s not just people who have
sensitive information on their network who should use security. Everybody who uses any wireless network
should ensure that effective security is in place.
A good way to come up with effective security keys, passwords and so on is to use obscure information
that you personally will easily remember, and to enter it in a way that appears random and does not
include real words. For example, if your mother owns a 1970 Dodge Challenger and her favorite movie is
Vanishing Point (which you know was made in 1971) you could use “70dodchal71vanpoi” as your
security key.
The following sections introduce different types of wireless security you can set up in the wireless
network.
5.6.3.1 SSID
Normally, the LTE4506 acts like a beacon and regularly broadcasts the SSID in the area. You can hide
the SSID instead, in which case the LTE4506 does not broadcast the SSID. In addition, you should change
the default SSID to something that is difficult to guess.
This type of security is fairly weak, however, because there are ways for unauthorized wireless devices to
get the SSID. In addition, unauthorized wireless devices can still see the information that is sent in the
wireless network.
5.6.3.2 MAC Address Filter
Every device that can use a wireless network has a unique identification number, called a MAC
address.1 A MAC address is usually written using twelve hexadecimal characters2; for example,
00A0C5000002 or 00:A0:C5:00:00:02. To get the MAC address for each device in the wireless network,
see the device’s User’s Guide or other documentation.
You can use the MAC address filter to tell the LTE4506 which devices are allowed or not allowed to use
the wireless network. If a device is allowed to use the wireless network, it still has to have the correct
information (SSID, channel, and security). If a device is not allowed to use the wireless network, it does
not matter if it has the correct information.
This type of security does not protect the information that is sent in the wireless network. Furthermore,
there are ways for unauthorized wireless devices to get the MAC address of an authorized device. Then,
they can use that MAC address to use the wireless network.
1. Some wireless devices, such as scanners, can detect wireless networks but cannot use wireless networks. These
kinds of wireless devices might not have MAC addresses.
2. Hexadecimal characters are 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D, E, and F.
Chapter 5 Wi-Fi
LTE4506 User’s Guide
42
5.6.3.3 User Authentication
Authentication is the process of verifying whether a wireless device is allowed to use the wireless
network. You can make every user log in to the wireless network before using it. However, every device
in the wireless network has to support IEEE 802.1x to do this.
For wireless networks, you can store the user names and passwords for each user in a RADIUS server. This
is a server used in businesses more than in homes. If you do not have a RADIUS server, you cannot set up
user names and passwords for your users.
Unauthorized wireless devices can still see the information that is sent in the wireless network, even if they
cannot use the wireless network. Furthermore, there are ways for unauthorized wireless users to get a
valid user name and password. Then, they can use that user name and password to use the wireless
network.
5.6.3.4 Encryption
Wireless networks can use encryption to protect the information that is sent in the wireless network.
Encryption is like a secret code. If you do not know the secret code, you cannot understand the
message.
The types of encryption you can choose depend on the type of authentication. (See Section 5.6.3.3 on
page 42 for information about this.)
For example, if the wireless network has a RADIUS server, you can choose WPA or WPA2. If users do not
log in to the wireless network, you can choose no encryption, Static WEP, WPA-PSK, or WPA2-PSK.
Usually, you should set up the strongest encryption that every device in the wireless network supports. For
example, suppose you have a wireless network with the LTE4506 and you do not have a RADIUS server.
Therefore, there is no authentication. Suppose the wireless network has two devices. Device A only
supports WEP, and device B supports WEP and WPA. Therefore, you should set up Static WEP in the
wireless network.
Note: It is recommended that wireless networks use WPA-PSK, WPA, or stronger encryption.
The other types of encryption are better than none at all, but it is still possible for
unauthorized wireless devices to figure out the original information pretty quickly.
When you select WPA2 or WPA2-PSK in your LTE4506, you can also select an option (WPA compatible) to
support WPA as well. In this case, if some of the devices support WPA and some support WPA2, you
should set up WPA2-PSK or WPA2 (depending on the type of wireless network login) and select the WPA
compatible option in the LTE4506.
Many types of encryption use a key to protect the information in the wireless network. The longer the
key, the stronger the encryption. Every device in the wireless network must have the same key.
Table 21 Types of Encryption for Each Type of Authentication
NO AUTHENTICATION RADIUS SERVER
Weakest No Security WPA
Static WEP
WPA-PSK
Strongest WPA2-PSK WPA2
Chapter 5 Wi-Fi
LTE4506 User’s Guide
43
5.6.4 Signal Problems
Because wireless networks are radio networks, their signals are subject to limitations of distance,
interference and absorption.
Problems with distance occur when the two radios are too far apart. Problems with interference occur
when other radio waves interrupt the data signal. Interference may come from other radio
transmissions, such as military or air traffic control communications, or from machines that are
coincidental emitters such as electric motors or microwaves. Problems with absorption occur when
physical objects (such as thick walls) are between the two radios, muffling the signal.
5.6.5 WiFi Protected Setup (WPS)
Your LTE4506 supports WiFi Protected Setup (WPS), which is an easy way to set up a secure wireless
network. WPS is an industry standard specification, defined by the WiFi Alliance.
WPS allows you to quickly set up a wireless network with strong security, without having to configure
security settings manually. Each WPS connection works between two devices. Both devices must
support WPS (check each device’s documentation to make sure).
Depending on the devices you have, you can either press a button (on the device itself, or in its
configuration utility) or enter a PIN (a unique Personal Identification Number that allows one device to
authenticate the other) in each of the two devices. When WPS is activated on a device, it has two
minutes to find another device that also has WPS activated. Then, the two devices connect and set up
a secure network by themselves.
5.6.5.1 Push Button Configuration
WPS Push Button Configuration (PBC) is initiated by pressing a button on each WPS-enabled device, and
allowing them to connect automatically. You do not need to enter any information.
Not every WPS-enabled device has a physical WPS button. Some may have a WPS PBC button in their
configuration utilities instead of or in addition to the physical button.
Take the following steps to set up WPS using the button.
1Ensure that the two devices you want to set up are within wireless range of one another.
2Look for a WPS button on each device. If the device does not have one, log into its configuration utility
and locate the button (see the device’s User’s Guide for how to do this - for the LTE4506, see Section 5.5
on page 38).
3Press the button on one of the devices (it doesn’t matter which). For the LTE4506 you must press the WPS
button for more than three seconds.
4Within two minutes, press the button on the other device. The registrar sends the network name (SSID)
and security key through an secure connection to the enrollee.
If you need to make sure that WPS worked, check the list of associated wireless clients in the AP’s
configuration utility. If you see the wireless client in the list, WPS was successful.
Chapter 5 Wi-Fi
LTE4506 User’s Guide
44
5.6.5.2 PIN Configuration
Each WPS-enabled device has its own PIN (Personal Identification Number). This may either be static (it
cannot be changed) or dynamic (in some devices you can generate a new PIN by clicking on a button
in the configuration interface).
Use the PIN method instead of the push-button configuration (PBC) method if you want to ensure that
the connection is established between the devices you specify, not just the first two devices to activate
WPS in range of each other. However, you need to log into the configuration interfaces of both devices
to use the PIN method.
When you use the PIN method, you must enter the PIN from one device (usually the wireless client) into
the second device (usually the Access Point or wireless router). Then, when WPS is activated on the first
device, it presents its PIN to the second device. If the PIN matches, one device sends the network and
security information to the other, allowing it to join the network.
Take the following steps to set up a WPS connection between an access point or wireless router
(referred to here as the AP) and a client device using the PIN method.
1Ensure WPS is enabled on both devices.
2Access the WPS section of the AP’s configuration interface. See the device’s User’s Guide for how to do
this.
3Look for the client’s WPS PIN; it will be displayed either on the device, or in the WPS section of the client’s
configuration interface (see the device’s User’s Guide for how to find the WPS PIN - for the LTE4506, see
Section 5.5 on page 38).
4Enter the client’s PIN in the AP’s configuration interface.
5If the client device’s configuration interface has an area for entering another device’s PIN, you can
either enter the client’s PIN in the AP, or enter the AP’s PIN in the client - it does not matter which.
6Start WPS on both devices within two minutes.
7Use the configuration utility to activate WPS, not the push-button on the device itself.
8On a computer connected to the wireless client, try to connect to the Internet. If you can connect, WPS
was successful.
If you cannot connect, check the list of associated wireless clients in the AP’s configuration utility. If you
see the wireless client in the list, WPS was successful.
The following figure shows a WPS-enabled wireless client (installed in a notebook computer) connecting
to the WPS-enabled AP via the PIN method.
Chapter 5 Wi-Fi
LTE4506 User’s Guide
45
Figure 25 Example WPS Process: PIN Method
5.6.5.3 How WPS Works
When two WPS-enabled devices connect, each device must assume a specific role. One device acts
as the registrar (the device that supplies network and security settings) and the other device acts as the
enrollee (the device that receives network and security settings. The registrar creates a secure EAP
(Extensible Authentication Protocol) tunnel and sends the network name (SSID) and the WPA-PSK or
WPA2-PSK pre-shared key to the enrollee. Whether WPA-PSK or WPA2-PSK is used depends on the
standards supported by the devices. If the registrar is already part of a network, it sends the existing
information. If not, it generates the SSID and WPA(2)-PSK randomly.
The following figure shows a WPS-enabled client (installed in a notebook computer) connecting to a
WPS-enabled access point.
ENROLLEE
SECURE EAP TUNNEL
SSID
WPA(2)-PSK
WITHIN 2 MINUTES
COMMUNICATION
This device’s
WPS
Enter WPS PIN
WPS
from other device:
WPS PIN: 123456
WPS
START
WPS
START
REGISTRAR
Chapter 5 Wi-Fi
LTE4506 User’s Guide
46
Figure 26 How WPS works
The roles of registrar and enrollee last only as long as the WPS setup process is active (two minutes). The
next time you use WPS, a different device can be the registrar if necessary.
The WPS connection process is like a handshake; only two devices participate in each WPS transaction.
If you want to add more devices you should repeat the process with one of the existing networked
devices and the new device.
Note that the access point (AP) is not always the registrar, and the wireless client is not always the
enrollee. All WPS-certified APs can be a registrar, and so can some WPS-enabled wireless clients.
By default, a WPS devices is “unconfigured”. This means that it is not part of an existing network and can
act as either enrollee or registrar (if it supports both functions). If the registrar is unconfigured, the security
settings it transmits to the enrollee are randomly-generated. Once a WPS-enabled device has
connected to another device using WPS, it becomes “configured”. A configured wireless client can still
act as enrollee or registrar in subsequent WPS connections, but a configured access point can no longer
act as enrollee. It will be the registrar in all subsequent WPS connections in which it is involved. If you
want a configured AP to act as an enrollee, you must reset it to its factory defaults.
5.6.5.4 Example WPS Network Setup
This section shows how security settings are distributed in an example WPS setup.
The following figure shows an example network. In step 1, both AP1 and Client 1 are unconfigured.
When WPS is activated on both, they perform the handshake. In this example, AP1 is the registrar, and
Client 1 is the enrollee. The registrar randomly generates the security information to set up the network,
since it is unconfigured and has no existing information.
SECURE TUNNEL
SECURITY INFO
WITHIN 2 MINUTES
COMMUNICATION
ACTIVATE
WPS
ACTIVATE
WPS
WPS HANDSHAKE
REGISTRARENROLLEE
Chapter 5 Wi-Fi
LTE4506 User’s Guide
47
Figure 27 WPS: Example Network Step 1
In step 2, you add another wireless client to the network. You know that Client 1 supports registrar mode,
but it is better to use AP1 for the WPS handshake with the new client since you must connect to the
access point anyway in order to use the network. In this case, AP1 must be the registrar, since it is
configured (it already has security information for the network). AP1 supplies the existing security
information to Client 2.
Figure 28 WPS: Example Network Step 2
In step 3, you add another access point (AP2) to your network. AP2 is out of range of AP1, so you cannot
use AP1 for the WPS handshake with the new access point. However, you know that Client 2 supports
the registrar function, so you use it to perform the WPS handshake instead.
REGISTRARENROLLEE
SECURITY INFO
CLIENT 1 AP1
REGISTRAR
CLIENT 1 AP1
ENROLLEE
CLIENT 2
EXISTING CONNECTION
SECURITY INFO
Chapter 5 Wi-Fi
LTE4506 User’s Guide
48
Figure 29 WPS: Example Network Step 3
5.6.5.5 Limitations of WPS
WPS has some limitations of which you should be aware.
• WPS works in Infrastructure networks only (where an AP and a wireless client communicate). It does
not work in Ad-Hoc networks (where there is no AP).
• When you use WPS, it works between two devices only. You cannot enroll multiple devices
simultaneously, you must enroll one after the other.
For instance, if you have two enrollees and one registrar you must set up the first enrollee (by pressing
the WPS button on the registrar and the first enrollee, for example), then check that it successfully
enrolled, then set up the second device in the same way.
• WPS works only with other WPS-enabled devices. However, you can still add non-WPS devices to a
network you already set up using WPS.
WPS works by automatically issuing a randomly-generated WPA-PSK or WPA2-PSK pre-shared key
from the registrar device to the enrollee devices. Whether the network uses WPA-PSK or WPA2-PSK
depends on the device. You can check the configuration interface of the registrar device to discover
the key the network is using (if the device supports this feature). Then, you can enter the key into the
non-WPS device and join the network as normal (the non-WPS device must also support WPA-PSK or
WPA2-PSK).
• When you use the PBC method, there is a short period (from the moment you press the button on one
device to the moment you press the button on the other device) when any WPS-enabled device
could join the network. This is because the registrar has no way of identifying the “correct” enrollee,
and cannot differentiate between your enrollee and a rogue device. This is a possible way for a
hacker to gain access to a network.
You can easily check to see if this has happened. WPS works between only two devices
simultaneously, so if another device has enrolled your device will be unable to enroll, and will not
have access to the network. If this happens, open the access point’s configuration interface and look
at the list of associated clients (usually displayed by MAC address). It does not matter if the access
CLIENT 1 AP1
REGISTRAR
CLIENT 2
EXISTING CONNECTION
SECURITY INFO
ENROLLEE
AP2
EXISTING CONNECTION
Chapter 5 Wi-Fi
LTE4506 User’s Guide
49
point is the WPS registrar, the enrollee, or was not involved in the WPS handshake; a rogue device
must still associate with the access point to gain access to the network. Check the MAC addresses of
your wireless clients (usually printed on a label on the bottom of the device). If there is an unknown
MAC address you can remove it or reset the AP.
LTE4506 User’s Guide
50
CHAPTER 6
Router
6.1 Overview
This chapter describes how you can configure the management IP address, DHCP settings of your
LTE4506, the IP filtering and content filtering settings.
The Internet Protocol (IP) address identifies a device on a network. Every networking device (including
computers, servers, routers, printers, etc.) needs an IP address to communicate across the network.
These networking devices are also known as hosts.
6.1.1 What You Can Do in this Chapter
• Use the LAN IP screen to configure the LTE4506’s LAN IP address (Section 6.2 on page 50).
• Use the DHCP Server screen to enable the DHCP server on the LTE4506 (Section 6.3 on page 51).
• Use the DNS Settings screen to configure the LTE4506’s DNS settings (Section 6.4 on page 53).
• Use the Connected Devices screen to view current clients information (Section 6.5 on page 53).
• Use the IPv4/Port Filter screen to view and configure IPv4/Port filtering rules (Section 6.6 on page 54).
• Use the IPv6/Port Filter screen to view and configure IPv6/Port filtering rules (Section 6.7 on page 55).
• Use the URL Filter screen to view and configure content filtering rules (Section 6.8 on page 56).
• Use the IP/Port Forwarding screen to view and configure port forwarding rules (Section 6.9 on page
57).
6.2 LAN IP Screen
Use this screen to view or configure the management IP address for your LTE4506. To access this screen,
click Router > LAN IP.
Note: If you change the LTE4506’s IP address, you need to use the new IP address to access
the LTE4506’s web configurator.
Chapter 6 Router
LTE4506 User’s Guide
51
Figure 30 Router > LAN IP
The following table describes the labels in this screen.
6.3 DHCP Server Screen
The LTE4506 has built-in DHCP server capability that assigns IP addresses to systems that support DHCP
client capability. Use this screen to enable the DHCP server. To access this screen, click Router > DHCP
Server.
Table 22 Router > LAN IP
LABEL DESCRIPTION
Host Name This shows the default host name.
Enter the new host name for the LTE4506 if you want to change it.
IP Address This shows the default LAN IP address.
Enter the new IP address for the LTE4506’s LAN interface if you want to change it.
Subnet Mask This shows the default subnet mask.
Enter the subnet mask of this interface in dot decimal notation. The subnet mask indicates
what part of the IP address is the same for all computers in the network.
Apply Click Apply to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
Chapter 6 Router
LTE4506 User’s Guide
52
Figure 31 Router > DHCP Server
The following table describes the labels in this screen.
Table 23 Router > DHCP Server
LABEL DESCRIPTION
DHCP Settings
Enable DHCP Server Select the check box to enable the DHCP server on the LTE4506.
Start IP The LTE4506 is pre-configured with a pool of 240 IP addresses starting from 192.168.0.10 to
192.168.0.250.
This field specifies the first of the contiguous addresses in the IP address pool.
End IP This field specifies the last of the contiguous addresses in the IP address pool.
Lease Time (minutes) Specify how long (in minutes) each computer can use the information (especially the IP
address) before it has to request the information again.
Static DHCP List
Add New Click Add New to create a new entry.
This field displays the index number of the static IP address entry.
IP Address This field displays the IP address that the LTE4506 assigns to a device with the entry’s MAC
address.
MAC Address This field displays the MAC address of the device to which the LTE4506 assigns the entry’s IP
address.
Action Click Edit to go to the screen where you can edit the static IP address.
Click Delete to remove the static IP address entry.
Apply Click this button to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
Chapter 6 Router
LTE4506 User’s Guide
53
6.4 DNS Settings Screen
Click Router > DNS Settings to configure the LTE4506’s DNS settings. The following screen displays.
Figure 32 Router > DNS Settings
The following table describes the labels in this screen.
6.5 Connected Devices Screen
Click Router > Connected Devices to view current clients information (including IP Address, Host Name
and MAC Address) of network clients connected to the LTE4506. The following screen displays.
Figure 33 Router > Connected Devices
Table 24 Router > DNS Settings
LABEL DESCRIPTION
DNS Mode Select Auto if your ISP dynamically assigns DNS server information (and the LTE4506's WAN IP
address). Otherwise, select Manual if you have the IP address of a DNS server.
Primary DNS
Secondary DNS
Select Manual if you have the IP address of a DNS server.
Enter the DNS server's IP address in the field.
Apply Click this button to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
Chapter 6 Router
LTE4506 User’s Guide
54
The following table describes the labels in this screen.
6.6 IPv4/Port Filter Screen
The LTE4506 firewall is a packet filtering firewall and restricts access based on the source/destination
computer network address of a packet and the type of application. Use this screen to configure IP
filtering rules. To access this screen, click Router > Firewall > IPv4/Port Filter.
Figure 34 Router > Firewall > IPv4/Port Filter
The following table describes the labels in this screen.
Table 25 Router > Connected Devices
LABEL DESCRIPTION
MAC Address This field displays the MAC address of the device.
Host Name (If
any)
This field displays the device host name.
IP Address This field displays the IP address that the LTE4506 assigns to the device.
Table 26 Router > Firewall > IPv4/Port Filter
LABEL DESCRIPTION
IPv4/Port Filter
Enable IPv4/Port
Filter
Select the check box to enable the rule.
IPv4/Port
Filtering Policy
Select Whitelist to allow packets that match the filtering rules defined on this screen to pass
through. Select Blacklist to block packets that match the filtering rules defined on this screen.
IPv4/Port Filter List
Add New Click Add New to create a new rule.
This field displays the rule index number.
Source IP This field displays the source IPv4 addresses to which this rule applies.
Chapter 6 Router
LTE4506 User’s Guide
55
6.7 IPv6/Port Filter Screen
The LTE4506 firewall is a packet filtering firewall and restricts access based on the source/destination
computer network address of a packet and the type of application. Use this screen to configure IP
filtering rules. To access this screen, click Router > Firewall > IPv6/Port Filter.
Figure 35 Router > Firewall > IPv6/Port Filter
The following table describes the labels in this screen.
Port This field displays a single port number of the source or a port range.
Enter the port number/range of the source that define the traffic type, for example TCP port 80
defines web traffic.
Protocol This field displays the protocol (TCP, UDP, TCP+UDP or any) used to transport the packets for
which you want to apply the rule.
Dest. IP This field displays the destination IPv4 addresses to which this rule applies.
Port This field displays a single port number of the destination or a port range.
Enter the port number/range of the destination that define the traffic type, for example TCP port
80 defines web traffic.
Comment Enter descriptions of the rule in this field.
Action Click Edit to go to the screen where you can edit the filtering rule.
Click Delete to remove the filtering rule.
Apply Click this button to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
Table 26 Router > Firewall > IPv4/Port Filter
LABEL DESCRIPTION
Table 27 Router > Firewall > IPv6/Port Filter
LABEL DESCRIPTION
IPv6/Port Filter
Enable IPv6/Port
Filter
Select the check box to enable the rule.
Chapter 6 Router
LTE4506 User’s Guide
56
6.8 URL Filter Screen
Use this screen to block the users on your network from accessing certain web sites. To access this
screen, click Router > Firewall > URL Filter.
IPv6/Port
Filtering Policy
Select Whitelist to allow packets that match the filtering rules defined on this screen to pass
through. Select Blacklist to block packets that match the filtering rules defined on this screen.
IPv6/Port Filter List
Add New Click Add New to create a new rule.
This field displays the rule index number.
Source IP This field displays the source IPv6 addresses to which this rule applies.
Port This field displays a single port number of the source or a port range.
Enter the port number/range of the source that define the traffic type, for example TCP port 80
defines web traffic.
Protocol This field displays the protocol (TCP, UDP, TCP+UDP or any) used to transport the packets for
which you want to apply the rule.
Dest. IP This field displays the destination IPv6 addresses to which this rule applies.
Port This field displays a single port number of the destination or a port range.
Enter the port number/range of the destination that define the traffic type, for example TCP port
80 defines web traffic.
Comment Enter descriptions of the rule in this field.
Action Click Edit to go to the screen where you can edit the filtering rule.
Click Delete to remove the filtering rule.
Apply Click this button to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
Table 27 Router > Firewall > IPv6/Port Filter
LABEL DESCRIPTION
Chapter 6 Router
LTE4506 User’s Guide
57
Figure 36 Router > Firewall > URL Filter
The following table describes the labels in this screen.
6.9 IP/Port Forwarding Screen
Use this screen to configure port forwarding rules. To access this screen, click Router > Firewall > IP/Port
Forwarding.
Table 28 Router > Firewall > URL Filter
LABEL DESCRIPTION
URL filter
Enable URL Filter Select the check box to enable the rule.
URL Filtering
Policy
Select Whitelist to allow users to access the websites that match the filtering rules defined on this
screen. Select Blacklist to block users to access the websites that match the filtering rules
defined on this screen.
URL filter List
Add New Click Add New to create a new rule.
This field displays the rule index number.
Keywords of URL
or Domain
This field displays the keywords of URL or domain to which the LTE4506 block or allow.
Action Click Edit to go to the screen where you can edit the filtering rule.
Click Delete to remove the filtering rule.
Apply Click this button to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
Chapter 6 Router
LTE4506 User’s Guide
58
Figure 37 Router > Firewall > IP/Port Forwarding
The following table describes the labels in this screen.
Table 29 Router > Firewall > IP/Port Forwarding
LABEL DESCRIPTION
IP/Port Forwarding
Enable IP/Port
Forwarding
Select the check box to enable port forwarding rules.
Filter List
Add New Click Add New to create a new rule.
This field displays the rule index number.
Private IP This field displays the inside IP address of the server.
Enter the inside IP address of the virtual server here.
Private Port A private port is a port that causes (or triggers) the LTE4506 to record the IP address of the LAN
computer that sent the traffic to a server on the WAN.
Enter the port number/range of the private in this field.
Global Port A global port is a port that a server on the WAN uses when it sends out a particular service. The
LTE4506 forwards the traffic with this port to the client computer on the LAN that requested the
service.
Enter the port number/range of the global in this field.
Protocol This field displays the protocol (TCP, UDP, TCP+UDP) used to transport the packets for which you
want to apply the rule.
Action Click Edit to go to the screen where you can edit the port forwarding rule.
Click Delete to remove the port forwarding rule.
Apply Click this button to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
LTE4506 User’s Guide
59
CHAPTER 7
Applications
7.1 Overview
This chapter shows you how to set up a contact list, send and view the text messages.
SMS (Short Message Service) allows you to send and view the text messages that the LTE4506 received
from mobile devices or the service provider.
When the SMS box is full the LTE4506 will begin to delete older entries as it adds new ones.
7.1.1 What You Can Do in this Chapter
• Use the Application > Contacts > Contact List screen to configure the contact list saved on the
LTE4506 (Section 7.2 on page 59).
• Use the Application > Contacts > SIM Contacts screen to view the contact list saved on the SIM card
(Section 7.3 on page 60).
• Use the Application > Contacts > Contacts Settings screen to import or export the contacts files
(Section 7.4 on page 61).
• Use the Application > Short Message > New SMS screen to send new messages (Section 7.5 on page
61).
• Use the Application > Short Message > Inbox screen to view messages received on the LTE4506
(Section 7.6 on page 62).
• Use the Application > Short Message > Outbox screen to view messages sent from the LTE4506
(Section 7.7 on page 63).
• Use the Application > Short Message > Draft screen to view messages not yet sent from the LTE4506
(Section 7.8 on page 63).
• Use the Application > Short Message > SIM SMS screen to view messages received on the SIM card
(Section 7.9 on page 64).
7.2 Contact List Screen
Use this screen to configure the contact list saved on the LTE4506. To access this screen, click
Application > Contacts > Contact List.
Chapter 7 Applications
LTE4506 User’s Guide
60
Figure 38 Application > Contacts > Contact List
The following table describes the labels in this screen.
7.3 SIM Contacts Screen
Use this screen to view the contact list saved on the SIM card. To access this screen, click Application >
Contacts > SIM Contacts.
Figure 39 Application > Contacts > SIM Contacts
The following table describes the labels in this screen.
Table 30 Application > Contacts > Contact List
LABEL DESCRIPTION
Delete Select the check box which next to the contact name and click Delete to remove the entry.
New Click New to create a new entry.
Contact Name This field displays a descriptive name used to identify contacts.
Number This field displays the mobile phone number of contacts.
Actions Click Edit to go to the screen where you can edit the contact details.
Table 31 Application > Contacts > SIM Contacts
LABEL DESCRIPTION
This field displays the index number of the contacts.
Contact Name This field displays a descriptive name used to identify contacts.
Number This field displays the mobile phone number of contacts.
Chapter 7 Applications
LTE4506 User’s Guide
61
7.4 Contacts Settings Screen
Use this screen to import or export the contacts files. To access this screen, click Application > Contacts >
Contacts Settings.
Figure 40 Application > Contacts > Contacts Settings
The following table describes the labels in this screen.
7.5 New SMS Screen
Use this screen to send messages using the LTE4506. To access this screen, click Application > Short
Message > New SMS.
Type a phone number and message content. You can type up to 140 English characters (70 Chinese
characters) in one message. If the message exceeds 140 English characters, more than one message
will be sent. The maximum number of SMS that can be sent is 8 (1000 English characters or 500 Chinese
characters total). Click Send to send the message. Click Save to store the message as a draft. Click
Reset to reload the previous configuration for this screen.
Table 32 Application > Contacts > Contacts Settings
LABEL DESCRIPTION
Import Contacts
Import from File Click Choose File to find the .csv file you want to upload. Remember that you must decompress
compressed (.zip) files before you can upload them.
You can select a .csv or .vcf file, then click import to begin upload process.
Export Contacts
Export to File A csv (comma-separated values) file is a way to store textual and numeric data. A vcard is an
electronic business card, and it can store images and sound as well as text.
Select a contact format from the drop-down list box to export your contacts.
Click Export to begin the download process.
Chapter 7 Applications
LTE4506 User’s Guide
62
Figure 41 Application > Short Message > New SMS
7.6 Inbox Screen
Use this screen to view messages received on the LTE4506. To access this screen, click Application >
Short Message > Inbox.
Figure 42 Application > Short Message > Inbox
The following table describes the labels in this screen.
Table 33 Application > Short Message > Inbox
LABEL DESCRIPTION
Delete All Click Delete All to remove all messages.
This field displays the index number of the message.
From This field displays the name from which the message is sent.
Time This field displays the date and time the message was received.
Content This field displays the content of the message.
Action Click Delete to remove the message record.
Chapter 7 Applications
LTE4506 User’s Guide
63
7.7 Outbox Screen
Use this screen to view messages sent from the LTE4506. To access this screen, click Application > Short
Message > Outbox.
Figure 43 Application > Short Message > Outbox
The following table describes the labels in this screen.
7.8 Draft Screen
Use this screen to view messages not yet sent from the LTE4506. To access this screen, click Application >
Short Message > Draft.
Figure 44 Application > Short Message > Draft
Table 34 Application > Short Message > Outbox
LABEL DESCRIPTION
Delete All Click Delete All to remove all messages.
This field displays the index number of the message.
To This field displays the name the message is sent to.
Time This field displays the date and time the message was sent.
Content This field displays the content of the message.
Action Click Delete to remove the message record.
Chapter 7 Applications
LTE4506 User’s Guide
64
The following table describes the labels in this screen.
7.9 SIM SMS Screen
Use this screen to view messages received on the SIM card. To access this screen, click Application >
Short Message > SIM SMS.
Figure 45 Application > Short Message > SIM SMS
The following table describes the labels in this screen.
Table 35 Application > Short Message > Draft
LABEL DESCRIPTION
Delete All Click Delete All to remove all messages.
This field displays the index number of the message.
To This field displays the name the message is sent to.
Time This field displays the date and time the message was sent.
Content This field displays the content of the message.
Action Click Delete to remove the message record.
Click Send to deliver the message.
Table 36 Application > Short Message > SIM SMS
LABEL DESCRIPTION
Delete All Click Delete All to remove all messages.
This field displays the index number of the message.
From This field displays the mobile phone number from which the message is sent.
Time This field displays the date and time the message was received.
Content This field displays the content of the message.
Action Click Delete to remove the message record.
LTE4506 User’s Guide
65
CHAPTER 8
System
8.1 Overview
Use the system screens to configure general LTE4506 settings.
8.1.1 What You Can Do in this Chapter
• Use the System Information screen to view basic information about the LTE4506 and restart the
LTE4506 (Section 8.2 on page 65).
• Use the User Account screen to set the domain name and change the LTE4506’s system password
(Section 8.3 on page 67).
• Use the Settings Profile screen to reset your device settings back to the factory default, backup
configuration, and restoring configuration (Section 8.4 on page 68).
• Use the Firmware Upgrade screen to upload new firmware to your LTE4506 (Section 8.5 on page 70).
• Use the Time Settings screen to change the LTE4506’s time and date and configure daylight saving
time (Section 8.6 on page 71).
• Use the System Log screens to view logged messages and specify to where the LTE4506 is to send logs
(Section 8.7 on page 73).
8.2 System Information Screen
Use this screen to view basic information about the LTE4506 and restart the LTE4506. To access this
screen, click System > System Information.
Chapter 8 System
LTE4506 User’s Guide
66
Figure 46 System > System Information
The following table describes the labels in this screen.
Table 37 System > System Information
LABEL DESCRIPTION
About the 4G Hotspot
Firmware
Version
This displays the current firmware version of the LTE4506.
IMEI This displays the International Mobile Equipment Number (IMEI) which is the serial number of the
built-in 3G module. IMEI is a unique 15-digit number used to identify a mobile device.
Hardware
Version
This displays the hardware version of the LTE4506.
Wi-Fi1 MAC
Address
Wi-Fi2 MAC
Address
This is the MAC address of the wireless network.
Reboot Device
Reboot Device Click Reboot to restart the device. Wait a few minutes until the login screen appears. If the login
screen does not appear, type the IP address of the device in your Web browser.
Bridge Mode
Chapter 8 System
LTE4506 User’s Guide
67
8.3 User Account Screen
This screen allows you to set the domain name and change the LTE4506’s system password. It is strongly
recommended that you change your LTE4506's system password. To access this screen, click System >
User Account.
See Section 2.2 on page 12 for more information about login accounts.
Figure 47 System > User Account
The following table describes the labels in this screen.
Enable Bridge
Mode
Select this if you want the LTE4506 to work in bridge mode.
Apply Click this button to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
Table 37 System > System Information (continued)
LABEL DESCRIPTION
Table 38 System > User Account
LABEL DESCRIPTION
Login Web URL Setting
Web Domain Name Enter the domain name you want to give to the LTE4506.
Chapter 8 System
LTE4506 User’s Guide
68
8.4 Settings Profile Screen
The Settings Profile screen allows you to backup and restore device configurations. You can also reset
your device settings back to the factory default. To access this screen, click System > Settings Profile.
Apply Click Apply to save your changes back to the LTE4506.
User Settings
Username Enter your username of the system account.
Password Type your new system password. Note that as you type a password, the screen displays as
dot (.) for each character you type.
Confirm Password Type the new password again in this field.
Auto Logout After Type how many minutes a management session can be left idle before the session times out.
The default is 3 minutes. After it times out you have to log in with your password again.
Apply Click Apply to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
Table 38 System > User Account
LABEL DESCRIPTION
Chapter 8 System
LTE4506 User’s Guide
69
Figure 48 System > Settings Profile
8.4.1 Reset Settings
Click the Restore button to clear all user-entered configuration information and return the LTE4506 to its
factory defaults. The LTE4506 automatically restarts.
You can also press the Reset button on the rear panel to reset the factory defaults of your LTE4506. Refer
to Section 1.7 on page 10 for more information on the Reset button.
8.4.2 Save Current Settings
Enter the profile name you specified in the New Profile Name field, and click Save. The profile you saved
will be displayed in the Profile List field.
Chapter 8 System
LTE4506 User’s Guide
70
The following table describes the labels in this screen.
8.4.3 Import & Export Settings Profile
This screen allows you to upload a new or previously saved configuration file from your computer to your
LTE4506.
Type in the location of the file you want to upload in the Apply Profile from File field or click Choose File
to find it. Click Apply to begin the upload process. The LTE4506 automatically restarts.
Do not turn off the LTE4506 while configuration file upload is in progress.
Backup Configuration allows you to back up (save) the LTE4506’s current configuration to a file on your
computer. The configuration file should be saved and edited in UTF-8 (without BOM) format, if you’re
using Windows Notepad, make sure you choose File > Save as UTF-8 in the text editor. Once your
LTE4506 is configured and functioning properly, it is highly recommended that you back up your
configuration file before making configuration changes. The backup configuration file will be useful in
case you need to return to your previous settings.
Select one profile from the drop-down list box in the Export Profile to File field, and click Export to save
the LTE4506’s current configuration to your computer.
After the LTE4506 configuration has been restored successfully, the login screen appears. If you
uploaded the default configuration file you may need to change the IP address of your computer to be
in the same subnet as that of the default device IP address (192.168.1.1).
8.5 Firmware Upgrade Screen
This screen allows you to upload new firmware to your LTE4506. You can download new firmware
releases from your nearest Zyxel FTP site (or www.zyxel.com) to use to upgrade your device’s
performance.
Only use firmware for your device’s specific model.
To access this screen, click System > Firmware Upgrade. This screen displays the current firmware version
and status of the LTE4506. Type in the location of the file you want to upload in the Select Firmware File
field or click Choose File to find it. Remember that you must decompress compressed (.ZIP) files before
you can upload them. You can select the check box to return the LTE4506 to its factory defaults after
upgrading the new firmware. Click Apply to begin the upload process.
Table 39 System > Settings Profile
LABEL DESCRIPTION
This field displays the index number of the profile.
Profile Name This field displays the profile name you specified in the New Profile Name field.
Saved Date This field displays the saved time and date of the profile.
Action Click Apply to use the configuration to the LTE4506.
Click Delete to go to the screen where you can remove the profile.
Chapter 8 System
LTE4506 User’s Guide
71
The upload process uses HTTP (Hypertext Transfer Protocol) and may take up to two minutes. After a
successful upload, the system will reboot.
Do NOT turn off the LTE4506 while firmware upload is in progress!
Figure 49 System > Firmware Upgrade
8.6 Time Settings Screen
For effective scheduling and logging, the LTE4506 system time must be accurate. The LTE4506 has a
software mechanism to get the current time and date from an external server. To change your LTE4506’s
time zone, click System > Time Settings. The screen displays as shown. You can have the LTE4506 get the
date and time from a time server or change the IP address or URL of your time server.
Chapter 8 System
LTE4506 User’s Guide
72
Figure 50 System > Time Settings
The following table describes the labels in this screen.
Table 40 System > Time Settings
LABEL DESCRIPTION
Date & Time
Device time This field displays the present time and date of your LTE4506.
Set Automatically Select Prefer Cellular Service Time to have the LTE4506 get the time and date from the
cellular service server.
Select Prefer NTP server to have the LTE4506 get the time and date from the time server you
specify.
NTP Server
Time Zone Choose the time zone of your location. This will set the time difference between your time
zone and Greenwich Mean Time (GMT).
NTP Server 1~5 Enter the IP address or URL of your time server. Check with your ISP/network administrator if
you are unsure of this information.
Apply Click Apply to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
Chapter 8 System
LTE4506 User’s Guide
73
8.7 System Log Screen
Use this screen to specify which logs to display and to where the LTE4506 is to send logs. Click System >
System Log. The screen displays as shown.
Figure 51 System > System Log
he following table describes the labels in this screen.
Table 41 System > System Log
LABEL DESCRIPTION
System Log Setting
Enable Log Select the check box to enable system logging.
Log Level Select the level of the logs that the LTE4506 is to record and send to the syslog server.
The LTE4506 displays and records the logs with the level equal to or higher than what you
selected.
Chapter 8 System
LTE4506 User’s Guide
74
Enable Remote Log Select the check box to enable syslog logging.
Syslog logging sends a log to an external log server.
Remote Log Host Enter the domain name or IP address of the syslog server to which the LTE4506 sends the logs.
Remote Log Port Enter the port number of the syslog server.
Apply Click Apply to save your changes back to the LTE4506.
Reset Click Reset to reload the previous configuration for this screen.
System Log Display
The log wraps around and deletes the old entries after it fills. Select what logs you want to see from the Log Level
drop list. When you select a log level, the LTE4506 searches through all logs of that level or higher. The screen
displays the time the log message was recorded. It also displays the reason the log message was generated.
Refresh Click Refresh to renew the log screen.
Table 41 System > System Log
LABEL DESCRIPTION
LTE4506 User’s Guide
75
CHAPTER 9
Troubleshooting
9.1 Overview
This chapter offers some suggestions to solve problems you might encounter. The potential problems are
divided into the following categories.
•Power, and Hardware Installation
•LTE4506 Access and Login
•Internet Access
•Wireless Connections
9.2 Power, and Hardware Installation
The LTE4506 does not turn on. None of the LEDs turn on.
1Make sure the LTE4506 is correctly installed (refer to your Quick Start Guide).
2Press the power button to turn the LTE4506 on. See Section 1.5 on page 9 and Section 1.6 on page 9.
3If the problem continues, contact the vendor.
9.3 LTE4506 Access and Login
I forgot the password for the LTE4506.
1The default IP address is 192.168.1.1.
2If you changed the IP address and have forgotten it, you have to reset the device to its factory defaults.
See Section 1.7 on page 10.
I cannot see or access the Login screen in the web configurator.
Chapter 9 Troubleshooting
LTE4506 User’s Guide
76
1Make sure you are using the correct IP address.
• The default IP address is 192.168.1.1.
• If you changed the IP address, use the new IP address.
• If you changed the IP address and have forgotten it, see the troubleshooting suggestions for
LTE4506 Access and Login
2Make sure the LTE4506 is correctly installed and turned on. See the Quick Start Guide and Section 1.5 on
page 9.
3Make sure your Internet browser does not block pop-up windows and has JavaScripts.
4Make sure your computer is connected to the LTE4506 and is in the same subnet as the LTE4506.
5Reset the device to its factory defaults, and try to access the LTE4506 with the default IP address. See
Section 1.7 on page 10.
6Disconnect your computer from the Internet (Wireless and/or Ethernet) and then insert the LTE4506
again.
7If the problem continues, contact the vendor.
I forgot the password.
1The default password is 1234.
2If this does not work, you have to reset the device to its factory defaults. See Section 1.7 on page 10.
I can see the Login screen, but I cannot log in to the LTE4506.
1Make sure you have entered the user name and password correctly. The default password is 1234. This
fields are case-sensitive, so make sure [Caps Lock] is not on.
2This can happen when you fail to log out properly from your last session. Try logging in again after five
minutes.
3Disconnect and connect to the LTE4506 again.
4If this does not work, you have to reset the device to its factory defaults. See Section 1.7 on page 10.
9.4 Internet Access
I cannot access the Internet through a 3G/4G wireless WAN connection.
Chapter 9 Troubleshooting
LTE4506 User’s Guide
77
1Make sure you insert a 4G SIM card into the card slot before turning on the LTE4506.
2Make sure your mobile access information (such as APN) is entered correctly in the WAN screen. These
fields are case-sensitive, so make sure [Caps Lock] is not on. Check with your service provider for the
correct APN if you don't have it.
3Make sure your SIM card’s account is valid and has an active data plan. Check your service contract or
contact your service provider directly.
4If you are using a pre-paid SIM card, insert the SIM card on another mobile device to check if the SIM
card still works. If the SIM card works without any problems on another mobile device, contact the
vendor. Otherwise, contact your service provider.
5If the problem continues, contact your ISP.
I cannot access the Internet anymore. I had access to the Internet (with the LTE4506), but my
Internet connection is not available anymore.
1Reboot the LTE4506.
2If the problem continues, contact your ISP.
The Internet connection is slow or intermittent.
1There might be a lot of traffic on the network. If the LTE4506 is sending or receiving a lot of information, try
closing some programs that use the Internet, especially peer-to-peer applications.
2Check the signal strength. If the signal strength is low, try moving the LTE4506 closer to the ISP’s base
station if possible, and look around to see if there are any devices that might be interfering with the
wireless network (for example, microwaves, other wireless networks, and so on).
3Reboot the LTE4506.
4If the problem continues, contact the network administrator or vendor.
9.5 Wireless Connections
I cannot access the LTE4506 or ping any computer from the WLAN.
1Make sure the wireless LAN is enabled on the LTE4506.
2Make sure the wireless adapter (installed on your computer) is working properly.
Chapter 9 Troubleshooting
LTE4506 User’s Guide
78
3Make sure the wireless adapter (installed on your computer) is IEEE 802.11 compatible and supports the
same wireless standard as the LTE4506’s active radio.
4Make sure your computer (with a wireless adapter installed) is within the transmission range of the
LTE4506.
5Check that both the LTE4506 and your computer are using the same wireless and wireless security
settings.
I can only see newer logs. Older logs are missing.
When a log reaches the maximum number of log messages, new log messages automatically overwrite
existing log messages, starting with the oldest existing log message first.
9.6 Getting More Troubleshooting Help
Search for support information for your model at www.zyxel.com for more troubleshooting suggestions.
NCC User’s Guide
79
APPENDIX A
Customer Support
In the event of problems that cannot be solved by using this manual, you should contact your vendor. If
you cannot contact your vendor, then contact a Zyxel office for the region in which you bought the
device.
See http://www.zyxel.com/homepage.shtml and also
http://www.zyxel.com/about_zyxel/zyxel_worldwide.shtml for the latest information.
Please have the following information ready when you contact an office.
Required Information
• Product model and serial number.
• Warranty Information.
• Date that you received your device.
• Brief description of the problem and the steps you took to solve it.
Corporate Headquarters (Worldwide)
Taiwan
• Zyxel Communications Corporation
• http://www.zyxel.com
Asia
China
• Zyxel Communications (Shanghai) Corp.
Zyxel Communications (Beijing) Corp.
Zyxel Communications (Tianjin) Corp.
• http://www.zyxel.cn
India
• Zyxel Technology India Pvt Ltd
• http://www.zyxel.in
Kazakhstan
• Zyxel Kazakhstan
• http://www.zyxel.kz
Appendix A Customer Support
NCC User’s Guide
80
Korea
• Zyxel Korea Corp.
• http://www.zyxel.kr
Malaysia
• Zyxel Malaysia Sdn Bhd.
• http://www.zyxel.com.my
Pakistan
• Zyxel Pakistan (Pvt.) Ltd.
• http://www.zyxel.com.pk
Philippines
• Zyxel Philippines
• http://www.zyxel.com.ph
Singapore
• Zyxel Singapore Pte Ltd.
• http://www.zyxel.com.sg
Taiwan
• Zyxel Communications Corporation
• http://www.zyxel.com/tw/zh/
Thailand
• Zyxel Thailand Co., Ltd
• http://www.zyxel.co.th
Vietnam
• Zyxel Communications Corporation-Vietnam Office
• http://www.zyxel.com/vn/vi
Europe
Austria
• Zyxel Deutschland GmbH
• http://www.zyxel.de
Belarus
• Zyxel BY
• http://www.zyxel.by
Appendix A Customer Support
NCC User’s Guide
81
Belgium
• Zyxel Communications B.V.
• http://www.zyxel.com/be/nl/
• http://www.zyxel.com/be/fr/
Bulgaria
• Zyxel България
• http://www.zyxel.com/bg/bg/
Czech Republic
• Zyxel Communications Czech s.r.o
• http://www.zyxel.cz
Denmark
• Zyxel Communications A/S
• http://www.zyxel.dk
Estonia
• Zyxel Estonia
• http://www.zyxel.com/ee/et/
Finland
• Zyxel Communications
• http://www.zyxel.fi
France
• Zyxel France
• http://www.zyxel.fr
Germany
• Zyxel Deutschland GmbH
• http://www.zyxel.de
Hungary
• Zyxel Hungary & SEE
• http://www.zyxel.hu
Italy
• Zyxel Communications Italy
• http://www.zyxel.it/
Appendix A Customer Support
NCC User’s Guide
82
Latvia
• Zyxel Latvia
• http://www.zyxel.com/lv/lv/homepage.shtml
Lithuania
• Zyxel Lithuania
• http://www.zyxel.com/lt/lt/homepage.shtml
Netherlands
• Zyxel Benelux
• http://www.zyxel.nl
Norway
• Zyxel Communications
• http://www.zyxel.no
Poland
• Zyxel Communications Poland
• http://www.zyxel.pl
Romania
• Zyxel Romania
• http://www.zyxel.com/ro/ro
Russia
• Zyxel Russia
• http://www.zyxel.ru
Slovakia
• Zyxel Communications Czech s.r.o. organizacna zlozka
• http://www.zyxel.sk
Spain
• Zyxel Communications ES Ltd
• http://www.zyxel.es
Sweden
• Zyxel Communications
• http://www.zyxel.se
Switzerland
• Studerus AG
Appendix A Customer Support
NCC User’s Guide
83
• http://www.zyxel.ch/
Turkey
• Zyxel Turkey A.S.
• http://www.zyxel.com.tr
UK
• Zyxel Communications UK Ltd.
• http://www.zyxel.co.uk
Ukraine
• Zyxel Ukraine
• http://www.ua.zyxel.com
Latin America
Argentina
• Zyxel Communication Corporation
• http://www.zyxel.com/ec/es/
Brazil
• Zyxel Communications Brasil Ltda.
• https://www.zyxel.com/br/pt/
Ecuador
• Zyxel Communication Corporation
• http://www.zyxel.com/ec/es/
Middle East
Israel
• Zyxel Communication Corporation
• http://il.zyxel.com/homepage.shtml
Middle East
• Zyxel Communication Corporation
• http://www.zyxel.com/me/en/
Appendix A Customer Support
NCC User’s Guide
84
North America
USA
• Zyxel Communications, Inc. - North America Headquarters
• http://www.zyxel.com/us/en/
Oceania
Australia
• Zyxel Communications Corporation
• http://www.zyxel.com/au/en/
Africa
South Africa
• Nology (Pty) Ltd.
• http://www.zyxel.co.za
LTE4506 User’s Guide
85
APPENDIX B
Common Services
The following table lists some commonly-used services and their associated protocols and port numbers.
For a comprehensive list of port numbers, ICMP type/code numbers and services, visit the IANA (Internet
Assigned Number Authority) web site.
•Name: This is a short, descriptive name for the service. You can use this one or create a different one,
if you like.
•Protocol: This is the type of IP protocol used by the service. If this is TCP/UDP, then the service uses the
same port number with TCP and UDP. If this is USER-DEFINED, the Port(s) is the IP protocol number, not
the port number.
•Port(s): This value depends on the Protocol. Please refer to RFC 1700 for further information about port
numbers.
• If the Protocol is TCP, UDP, or TCP/UDP, this is the IP port number.
• If the Protocol is USER, this is the IP protocol number.
•Description: This is a brief explanation of the applications that use this service or the situations in which
this service is used.
Table 42 Commonly Used Services
NAME PROTOCOL PORT(S) DESCRIPTION
AH (IPSEC_TUNNEL) User-Defined 51 The IPSEC AH (Authentication Header) tunneling
protocol uses this service.
AIM/New-ICQ TCP 5190 AOL’s Internet Messenger service. It is also used as a
listening port by ICQ.
AUTH TCP 113 Authentication protocol used by some servers.
BGP TCP 179 Border Gateway Protocol.
BOOTP_CLIENT UDP 68 DHCP Client.
BOOTP_SERVER UDP 67 DHCP Server.
CU-SEEME TCP
UDP
7648
24032
A popular videoconferencing solution from White
Pines Software.
DNS TCP/UDP 53 Domain Name Server, a service that matches web
names (for example www.zyxel.com) to IP numbers.
ESP (IPSEC_TUNNEL) User-Defined 50 The IPSEC ESP (Encapsulation Security Protocol)
tunneling protocol uses this service.
FINGER TCP 79 Finger is a UNIX or Internet related command that can
be used to find out if a user is logged on.
FTP TCP
TCP
20
21
File Transfer Program, a program to enable fast
transfer of files, including large files that may not be
possible by e-mail.
H.323 TCP 1720 NetMeeting uses this protocol.
HTTP TCP 80 Hyper Text Transfer Protocol - a client/server protocol
for the world wide web.
HTTPS TCP 443 HTTPS is a secured http session often used in e-
commerce.
Appendix B Common Services
LTE4506 User’s Guide
86
ICMP User-Defined 1 Internet Control Message Protocol is often used for
diagnostic or routing purposes.
ICQ UDP 4000 This is a popular Internet chat program.
IGMP (MULTICAST) User-Defined 2 Internet Group Management Protocol is used when
sending packets to a specific group of hosts.
IKE UDP 500 The Internet Key Exchange algorithm is used for key
distribution and management.
IRC TCP/UDP 6667 This is another popular Internet chat program.
MSN Messenger TCP 1863 Microsoft Networks’ messenger service uses this
protocol.
NEW-ICQ TCP 5190 An Internet chat program.
NEWS TCP 144 A protocol for news groups.
NFS UDP 2049 Network File System - NFS is a client/server distributed
file service that provides transparent file sharing for
network environments.
NNTP TCP 119 Network News Transport Protocol is the delivery
mechanism for the USENET newsgroup service.
PING User-Defined 1 Packet INternet Groper is a protocol that sends out
ICMP echo requests to test whether or not a remote
host is reachable.
POP3 TCP 110 Post Office Protocol version 3 lets a client computer
get e-mail from a POP3 server through a temporary
connection (TCP/IP or other).
PPTP TCP 1723 Point-to-Point Tunneling Protocol enables secure
transfer of data over public networks. This is the
control channel.
PPTP_TUNNEL (GRE) User-Defined 47 PPTP (Point-to-Point Tunneling Protocol) enables
secure transfer of data over public networks. This is
the data channel.
RCMD TCP 512 Remote Command Service.
REAL_AUDIO TCP 7070 A streaming audio service that enables real time
sound over the web.
REXEC TCP 514 Remote Execution Daemon.
RLOGIN TCP 513 Remote Login.
RTELNET TCP 107 Remote Telnet.
RTSP TCP/UDP 554 The Real Time Streaming (media control) Protocol
(RTSP) is a remote control for multimedia on the
Internet.
SFTP TCP 115 Simple File Transfer Protocol.
SMTP TCP 25 Simple Mail Transfer Protocol is the message-
exchange standard for the Internet. SMTP enables
you to move messages from one e-mail server to
another.
SNMP TCP/UDP 161 Simple Network Management Program.
SNMP-TRAPS TCP/UDP 162 Traps for use with the SNMP (RFC:1215).
SQL-NET TCP 1521 Structured Query Language is an interface to access
data on many different types of database systems,
including mainframes, midrange systems, UNIX
systems and network servers.
Table 42 Commonly Used Services (continued)
NAME PROTOCOL PORT(S) DESCRIPTION
Appendix B Common Services
LTE4506 User’s Guide
87
SSH TCP/UDP 22 Secure Shell Remote Login Program.
STRM WORKS UDP 1558 Stream Works Protocol.
SYSLOG UDP 514 Syslog allows you to send system logs to a UNIX server.
TACACS UDP 49 Login Host Protocol used for (Terminal Access
Controller Access Control System).
TELNET TCP 23 Telnet is the login and terminal emulation protocol
common on the Internet and in UNIX environments. It
operates over TCP/IP networks. Its primary function is
to allow users to log into remote host systems.
TFTP UDP 69 Trivial File Transfer Protocol is an Internet file transfer
protocol similar to FTP, but uses the UDP (User
Datagram Protocol) rather than TCP (Transmission
Control Protocol).
VDOLIVE TCP 7000 Another videoconferencing solution.
Table 42 Commonly Used Services (continued)
NAME PROTOCOL PORT(S) DESCRIPTION
WAH7706 User’s Guide
88
APPENDIX C
Legal Information
Copyright
Copyright © 2017 by Zyxel Communications Corporation.
The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any
language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or
otherwise, without the prior written permission of Zyxel Communications Corporation.
Published by Zyxel Communications Corporation. All rights reserved.
Disclaimer
Zyxel does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any
license under its patent rights nor the patent rights of others. Zyxel further reserves the right to make changes in any products described herein
without notice. This publication is subject to change without notice.
Regulatory Notice and Statement
UNITED STATES of AMERICA
The following information applies if you use the product within USA area.
FCC EMC Statement
• The device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
device.
• This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and
can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
• If this device does cause harmful interference to radio or television reception, which is found by turning the device off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the devices
• Connect the equipment to an outlet other than the receiver’s
• Consult a dealer or an experienced radio/TV technician for assistance
FCC Radiation Exposure Statement
• This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
• This transmitter must be at least 20 cm from the user and must not be co-located or operating in conjunction with any other antenna or
transmitter.
CANADA
The following information applies if you use the product within Canada area.
Industry Canada ICES statement
CAN ICES-3 (B)/NMB-3(B)
Industry Canada RSS-GEN & RSS-247 statement
• This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Appendix C Legal Information
WAH7706 User’s Guide
89
• This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible
gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than
the maximum gain indicated for that type, are strictly prohibited for use with this device.
If the product with 5G wireless function operating in 5150-5250 MHz and 5725-5850 MHz , the following attention must be paid,
• The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel
mobile satellite systems.
• For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the
equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and
• The worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in Section 6.2.2(3) of RSS 247
shall be clearly indicated.
If the product with 5G wireless function operating in 5250-5350 MHz and 5470-5725 MHz , the following attention must be paid.
• For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz
shall be such that the equipment still complies with the e.i.r.p. limit.
• Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
• Le présent émetteur radio de modèle s'il fait partie du matériel de catégorieI) a été approuvé par Industrie Canada pour fonctionner avec
les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les
types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation
de l'émetteur.
Lorsque la fonction sans fil 5G fonctionnant en 5150-5250 MHz and 5725-5850 MHz est activée pour ce produit , il est nécessaire de porter une
attention particulière aux choses suivantes
• Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques
de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
• Pour les dispositifs munis d’antennes amovibles, le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5 725 à 5 850 MHz)
doit être conforme à la limite de la p.i.r.e. spécifiée pour l'exploitation point à point et l’exploitation non point à point, selon le cas;
• Les pires angles d’inclinaison nécessaires pour rester conforme à l’exigence de la p.i.r.e. applicable au masque d’élévation, et énoncée à la
section 6.2.2 3) du CNR-247, doivent être clairement indiqués.
Lorsque la fonction sans fil 5G fonctionnant en 5250-5350 MHz et 5470-5725 MHz est activée pour ce produit , il est nécessaire de porter une
attention particulière aux choses suivantes.
• Pour les dispositifs munis d’antennes amovibles, le gain maximal d'antenne permis pour les dispositifs utilisant les bandes de 5 250 à 5 350 MHz
et de 5 470 à 5 725 MHz doit être conforme à la limite de la p.i.r.e.
Industry Canada radiation exposure statement
This device complies with IC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated
with a minimum distance of 20 cm between the radiator and your body.
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit
être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
EUROPEAN UNION
The following information applies if you use the product within the European Union.
Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive)
• Compliance information for 2.4GHz and/or 5GHz wireless products relevant to the EU and other Countries following the EU Directive 1999/5/
EC (R&TTE).
• This device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range.
Български
(Bulgarian)
С настоящото Zyxel декларира, че това оборудване е в съответствие със съществените изисквания и другите
приложими разпоредбите на Директива 1999/5/ЕC.
Español
(Spanish)
Por medio de la presente Zyxel declara que el equipo cumple con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Čeština
(Czech)
Zyxel tímto prohlašuje, že tento zařízení je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice
1999/5/EC.
Dansk (Danish) Undertegnede Zyxel erklærer herved, at følgende udstyr udstyr overholder de væsentlige krav og øvrige relevante krav i
direktiv 1999/5/EF.
Deutsch
(German)
Hiermit erklärt Zyxel, dass sich das Gerät Ausstattung in Übereinstimmung mit den grundlegenden Anforderungen und den
übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EU befindet.
Eesti keel
(Estonian)
Käesolevaga kinnitab Zyxel seadme seadmed vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist
tulenevatele teistele asjakohastele sätetele.
Appendix C Legal Information
WAH7706 User’s Guide
90
National Restrictions
• This product may be used in all EU countries (and other countries following the EU Directive 1999/5/EC) without any limitation except for the
countries mentioned below:
• Ce produit peut être utilisé dans tous les pays de l’UE (et dans tous les pays ayant transposés la directive 1999/5/CE) sans aucune limitation,
excepté pour les pays mentionnés ci-dessous:
• Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti gli altri paesi che seguono le direttiva 1999/5/EC) senza nessuna limitazione,
eccetto per i paesii menzionati di seguito:
• Das Produkt kann in allen EU Staaten ohne Einschränkungen eingesetzt werden (sowie in anderen Staaten die der Richtlinie 1999/5/CE
folgen) mit Außnahme der folgenden aufgeführten Staaten:
In the majority of the EU and other European countries, the 2.4GHz and 5GHz bands have been made available for the use of wireless local area
networks (LANs). Later in this document you will find an overview of countries in which additional restrictions or requirements or both are
applicable. The requirements for any country may evolve. Zyxel recommends that you check with the local authorities for the latest status of
their national regulations for both the 2.4GHz and 5GHz wireless LANs. The following countries have restrictions and/or requirements in addition to
those given in the table labeled “Overview of Regulatory Requirements for Wireless LANs”:.
Belgium
• The Belgian Institute for Postal Services and Telecommunications (BIPT) must be notified of any outdoor wireless link having a range
exceeding 300 meters. Please check http://www.bipt.be for more details.
• Draadloze verbindingen voor buitengebruik en met een reikwijdte van meer dan 300 meter dienen aangemeld te worden bij het Belgisch
Instituut voor postdiensten en telecommunicatie (BIPT). Zie http://www.bipt.be voor meer gegevens.
• Les liaisons sans fil pour une utilisation en extérieur d’une distance supérieure à 300 mètres doivent être notifiées à l’Institut Belge des services
Postaux et des Télécommunications (IBPT). Visitez http://www.ibpt.be pour de plus amples détails.
Denmark
• In Denmark, the band 5150 - 5350 MHz is also allowed for outdoor usage.
• I Danmark må frekvensbåndet 5150 - 5350 også anvendes udendørs.
Italy
Ελληνικά
(Greek)
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Zyxel ∆ΗΛΩΝΕΙ ΟΤΙ εξοπλισμός ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ
∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕC.
English Hereby, Zyxel declares that this device is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Français
(French)
Par la présente Zyxel déclare que l'appareil équipements est conforme aux exigences essentielles et aux autres dispositions
pertinentes de la directive 1999/5/EC.
Hrvatski
(Croatian)
Zyxel ovime izjavljuje da je radijska oprema tipa u skladu s Direktivom 1999/5/EC.
Íslenska
(Icelandic)
Hér með lýsir, Zyxel því yfir að þessi búnaður er í samræmi við grunnkröfur og önnur viðeigandi ákvæði tilskipunar 1999/5/EC.
Italiano (Italian) Con la presente Zyxel dichiara che questo attrezzatura è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti
stabilite dalla direttiva 1999/5/CE.
Latviešu valoda
(Latvian)
Ar šo Zyxel deklarē, ka iekārtas atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių kalba
(Lithuanian)
Šiuo Zyxel deklaruoja, kad šis įranga atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Magyar
(Hungarian)
Alulírott, Zyxel nyilatkozom, hogy a berendezés megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EK irányelv
egyéb elõírásainak.
Malti (Maltese) Hawnhekk, Zyxel, jiddikjara li dan tagħmir jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm
fid-Dirrettiva 1999/5/EC.
Nederlands
(Dutch)
Hierbij verklaart Zyxel dat het toestel uitrusting in overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EC.
Polski (Polish) Niniejszym Zyxel oświadcza, że sprzęt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami
Dyrektywy 1999/5/EC.
Português
(Portuguese)
Zyxel declara que este equipamento está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/
EC.
Română
(Romanian)
Prin prezenta, Zyxel declară că acest echipament este în conformitate cu cerinţele esenţiale şi alte prevederi relevante ale
Directivei 1999/5/EC.
Slovenčina
(Slovak)
Zyxel týmto vyhlasuje, že zariadenia spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/EC.
Slovenščina
(Slovene)
Zyxel izjavlja, da je ta oprema v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/EC.
Suomi (Finnish) Zyxel vakuuttaa täten että laitteet tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin
muiden ehtojen mukainen.
Svenska
(Swedish)
Härmed intygar Zyxel att denna utrustning står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta
bestämmelser som framgår av direktiv 1999/5/EC.
Norsk
(Norwegian)
Erklærer herved Zyxel at dette utstyret er I samsvar med de grunnleggende kravene og andre relevante bestemmelser I
direktiv 1999/5/EF.
Appendix C Legal Information
WAH7706 User’s Guide
91
• This product meets the National Radio Interface and the requirements specified in the National Frequency Allocation Table for Italy. Unless
this wireless LAN product is operating within the boundaries of the owner's property, its use requires a “general authorization.” Please check
http://www.sviluppoeconomico.gov.it/ for more details.
• Questo prodotto è conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle frequenze in Italia.
Se non viene installato all 'interno del proprio fondo, l'utilizzo di prodotti Wireless LAN richiede una “Autorizzazione Generale”. Consultare
http://www.sviluppoeconomico.gov.it/ per maggiori dettagli.
Latvia
• The outdoor usage of the 2.4 GHz band requires an authorization from the Electronic Communications Office. Please check http://
www.esd.lv for more details.
• 2.4 GHz frekvenèu joslas izmantoðanai ârpus telpâm nepiecieðama atïauja no Elektronisko sakaru direkcijas. Vairâk informâcijas: http://
www.esd.lv.
Notes:
1. Although Norway, Switzerland and Liechtenstein are not EU member states, the EU Directive 1999/5/EC has also been implemented in
those countries.
2. The regulatory limits for maximum output power are specified in EIRP. The EIRP level (in dBm) of a device can be calculated by adding the
gain of the antenna used(specified in dBi) to the output power available at the connector (specified in dBm).
List of national codes
Safety Warnings
• Do not use this product near water, for example, in a wet basement or near a swimming pool.
• Do not expose your device to dampness, dust or corrosive liquids.
• Do not store things on the device.
• Do not obstruct the device ventilation slots as insufficient airflow may harm your device. For example, do not place the device in an
enclosed space such as a box or on a very soft surface such as a bed or sofa.
• Do not install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning.
• Connect ONLY suitable accessories to the device.
• Do not open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified
service personnel should service or disassemble this device. Please contact your vendor for further information.
• Make sure to connect the cables to the correct ports.
• Place connecting cables carefully so that no one will step on them or stumble over them.
• Always disconnect all cables from this device before servicing or disassembling.
• Do not remove the plug and connect it to a power outlet by itself; always attach the plug to the power adaptor first before connecting it to
a power outlet.
• Do not allow anything to rest on the power adaptor or cord and do NOT place the product where anyone can walk on the power adaptor
or cord.
• Please use the provided or designated connection cables/power cables/ adaptors. Connect it to the right supply voltage (for example,
110V AC in North America or 230V AC in Europe). If the power adaptor or cord is damaged, it might cause electrocution. Remove it from the
device and the power source, repairing the power adapter or cord is prohibited. Contact your local vendor to order a new one.
• Do not use the device outside, and make sure all the connections are indoors. There is a remote risk of electric shock from lightning.
• CAUTION: Risk of explosion if battery is replaced by an incorrect type, dispose of used batteries according to the instruction. Dispose them at
the applicable collection point for the recycling of electrical and electronic devices. For detailed information about recycling of this
product, please contact your local city office, your household waste disposal service or the store where you purchased the product.
• The following warning statements apply, where the disconnect device is not incorporated in the device or where the plug on the power
supply cord is intended to serve as the disconnect device,
- For permanently connected devices, a readily accessible disconnect device shall be incorporated external to the device;
- For pluggable devices, the socket-outlet shall be installed near the device and shall be easily accessible.
COUNTRY ISO 3166 2 LETTER CODE COUNTRY ISO 3166 2 LETTER CODE
Austria AT Liechtenstein LI
Belgium BE Lithuania LT
Bulgaria BG Luxembourg LU
Croatia HR Malta MT
Cyprus CY Netherlands NL
Czech Republic CZ Norway NO
Denmark DK Poland PL
Estonia EE Portugal PT
Finland FI Romania RO
France FR Serbia RS
Germany DE Slovakia SK
Greece GR Slovenia SI
Hungary HU Spain ES
Iceland IS Switzerland CH
Ireland IE Sweden SE
Italy IT Turkey TR
Latvia LV United Kingdom GB
Appendix C Legal Information
WAH7706 User’s Guide
92
Environment Statement
ErP (Energy-related Products)
Zyxel products put on the EU market in compliance with the requirement of the European Parliament and the Council published Directive 2009/
125/EC establishing a framework for the setting of ecodesign requirements for energy-related products (recast), so called as "ErP Directive
(Energy-related Products directive) as well as ecodesign requirement laid down in applicable implementing measures, power consumption has
satisfied regulation requirements which are:
• Network standby power consumption < 8W, and/or
• Off mode power consumption < 0.5W, and/or
• Standby mode power consumption < 0.5W.
(Wireless setting, please refer to "Wireless" chapter for more detail.)
European Union - Disposal and Recycling Information
The symbol below means that according to local regulations your product and/or its battery shall be disposed of separately from domestic
waste. If this product is end of life, take it to a recycling station designated by local authorities. At the time of disposal, the separate collection of
your product and/or its battery will help save natural resources and ensure that the environment is sustainable development.
Die folgende Symbol bedeutet, dass Ihr Produkt und/oder seine Batterie gemäß den örtlichen Bestimmungen getrennt vom Hausmüll entsorgt
werden muss. Wenden Sie sich an eine Recyclingstation, wenn dieses Produkt das Ende seiner Lebensdauer erreicht hat. Zum Zeitpunkt der
Entsorgung wird die getrennte Sammlung von Produkt und/oder seiner Batterie dazu beitragen, natürliche Ressourcen zu sparen und die Umwelt
und die menschliche Gesundheit zu schützen.
El símbolo de abajo indica que según las regulaciones locales, su producto y/o su batería deberán depositarse como basura separada de la
doméstica. Cuando este producto alcance el final de su vida útil, llévelo a un punto limpio. Cuando llegue el momento de desechar el
producto, la recogida por separado éste y/o su batería ayudará a salvar los recursos naturales y a proteger la salud humana y
medioambiental.
Le symbole ci-dessous signifie que selon les réglementations locales votre produit et/ou sa batterie doivent être éliminés séparément des ordures
ménagères. Lorsque ce produit atteint sa fin de vie, amenez-le à un centre de recyclage. Au moment de la mise au rebut, la collecte séparée
de votre produit et/ou de sa batterie aidera à économiser les ressources naturelles et protéger l'environnement et la santé humaine.
Il simbolo sotto significa che secondo i regolamenti locali il vostro prodotto e/o batteria deve essere smaltito separatamente dai rifiuti domestici.
Quando questo prodotto raggiunge la fine della vita di servizio portarlo a una stazione di riciclaggio. Al momento dello smaltimento, la raccolta
separata del vostro prodotto e/o della sua batteria aiuta a risparmiare risorse naturali e a proteggere l'ambiente e la salute umana.
Symbolen innebär att enligt lokal lagstiftning ska produkten och/eller dess batteri kastas separat från hushållsavfallet. När den här produkten når
slutet av sin livslängd ska du ta den till en återvinningsstation. Vid tiden för kasseringen bidrar du till en bättre miljö och mänsklig hälsa genom att
göra dig av med den på ett återvinningsställe.
Appendix C Legal Information
WAH7706 User’s Guide
93
Environmental Product Declaration
Appendix C Legal Information
WAH7706 User’s Guide
94
⎘䀋
ẍᶳ妲〗怑䓐㕤䓊⑩℟㚱䃉䶂≇傥ᶼ扟ⓖ军⎘䀋⛘⋨
ɀ 䫔⋩Ḵ㡅 䴻✳⺷娵嫱⎰㟤Ỷ≇䌯⮬柣暣㨇炻朆䴻姙⎗炻℔⎠炻⓮嘇ㆾἧ䓐侭⛯ᶵ⼿㑭冒嬲㚜柣䌯ˣ≈⣏≇䌯ㆾ嬲㚜⍇姕妰䈡⿏⍲≇傥ˤ
ɀ 䫔⋩⚃㡅 Ỷ≇澯⮬柣暣㨇ἧ䓐澵⼿⼙枧梃凒⬱ℐ⍲⸚㒦⎰㱽忂ᾉ烊䴻䘤䎦㚱⸚㒦䎦尉㗪炻ㅱ灅⌛ 䓐炻㓡┬军䃉⸚㒦㗪㕡⼿两临ἧ䓐ˤ
⇵枭⎰㱽忂ᾉ炻㊯ὅ暣ᾉ㱽夷⭂ἄ㤕䃉䶂暣忂ᾉˤ Ỷ≇澯⮬柣暣㨇枰⽵⍿⎰㱽忂ᾉㆾⶍ㤕ˣ䥹⬠⍲慓瀏䓐暣㲊灕⮬⿏暣㨇姕⁁⸚㒦ˤ
ɀ 䃉䶂屯妲⁛廠姕⁁⽵⍿⎰㱽忂ᾉ⸚㒦ᶼ澵⼿⸚㒦⎰㱽忂ᾉ烊⤪忈ㆸ⸚㒦炻ㅱ灅⌛ 䓐炻 ᾇ䃉⸚㒦嘆炻⥳⼿两临ἧ䓐ˤ
ɀ 䃉䶂屯妲⁛姕⁁䘬墥忈⺈⓮ㅱ䡢ᾅ柣澯䨑⭂⿏炻⤪ὅ墥忈⺈⓮ἧ䓐ㇳℲᶲ徘㬋ⷠ㑵ἄ炻 䘤⮬䘬ᾉ嘇ㅱ䵕㊩㕤㑵ἄ柣ⷞ
ẍᶳ妲〗怑䓐㕤䓊⑩㑵ἄ㕤 6/36.6/46!䦕崓柣ⷞℏ扟ⓖ军⎘䀋⛘⋨
ɀ ⛐ 6/36.6/46!䦕崓柣ⷞℏ㑵ἄ䃉䶂屯妲⁛廠姕⁁炻旸㕤⭌ℏἧ䓐ˤ
ẍᶳ妲〗怑䓐㕤䓊⑩Ⱄ㕤⮰㤕⬱墅扟ⓖ军⎘䀋⛘⋨
ɀ 㛔☐㛸枰䴻⮰㤕ⶍ䦳Ṣ⒉⬱墅⍲姕⭂炻⥳⼿姕伖ἧ䓐炻ᶼ澵⼿䚜㍍屑ⓖ䴎ᶨ凔㴰屣侭ˤ
⬱ℐ嬎⏲!.!䁢Ḯぐ䘬⬱ℐ炻婳教嬨ẍᶳ嬎⏲⍲㊯䣢 ;
ɀ 婳⊧⮯㬌䓊⑩㍍役㯜ˣ䀓䃘ㆾ㓦伖⛐檀㹓䘬䑘⠫ˤ
ɀ 性姕⁁㍍妠 ;
.!ảỽ㵚橼!.!↯⊧嬻姕⁁㍍妠㯜ˣ暐㯜ˣ檀㽽⹎ˣ㰉㯜僸国⿏䘬㵚橼ㆾ℞Ṿ㯜ấˤ
.!䀘⠝⍲㰉䈑!.!↯⊧㍍妠䀘⠝ˣ㰉䈑ˣ㱁⛇ˣ梇䈑ㆾ℞Ṿᶵ⎰怑䘬㛸㕁ˤ
ɀ 暟暐⣑㯋㗪炻ᶵ天⬱墅炻ἧ䓐ㆾ䵕ᾖ㬌姕⁁ˤ㚱怕⍿暣㑲䘬桐晒ˤ
ɀ ↯⊧慵㏼ㆾ㑆㑲姕⁁炻⊧ἧ䓐ᶵ㬋䡢䘬暣㸸嬲⡻☐ˤ
ɀ 劍㍍ᶲᶵ㬋䡢䘬暣㸸嬲⡻☐㚫㚱䆮䁠䘬桐晒ˤ
ɀ 婳⊧晐シ㚜㎃䓊⑩ℏ䘬暣㰈ˤ
ɀ ⤪㝄㚜㎃ᶵ㬋䡢暣㰈✳⺷炻㚫㚱䆮䁠䘬桐晒炻婳ὅ墥忈⓮婒㖶㚠嗽䎮ἧ䓐忶暣㰈ˤ
ɀ 婳⮯⺊暣㰈㡬⛐怑䔞䘬暣☐ㆾ暣⫸姕⁁⚆㓞嗽ˤ
ɀ 婳⊧⮯姕⁁妋橼ˤ
ɀ 婳⊧旣䣁姕⁁䘬㔋䅙⫼炻䨢㯋⮵㳩ᶵ嵛⮯㚫忈ㆸ姕⁁㎵⭛ˤ
ɀ 婳㍺⛐㬋䡢䘬暣⡻ὃ䴎㍺⹏ )⤪;⊿伶0⎘䀋暣⡻ 221W!BD炻㫸㳚㗗 341W!BD*ˤ
ɀ `劍暣㸸嬲⡻☐ㆾ暣㸸嬲⡻☐䘬乄䶂㎵⢆炻婳⽆㍺⹏㉼昌炻劍ぐ怬两临㍺暣ἧ䓐炻㚫㚱妠暣㬣ṉ䘬桐晒ˤ
ɀ 婳⊧娎⚾ᾖ䎮暣㸸嬲⡻☐ㆾ暣㸸嬲⡻☐䘬乄䶂炻劍㚱㭨㎵炻婳䚜㍍倗䴉ぐ岤屟䘬⸿⭞炻岤屟ᶨᾳ㕘䘬暣㸸嬲⡻☐ˤ
ɀ 婳⊧⮯㬌姕⁁⬱墅㕤⭌⢾炻㬌姕⁁怑⎰㓦伖㕤⭌ℏˤ
ɀ 婳⊧晐ᶨ凔✫⛦㡬ˤ
ɀ 婳⍫教䓊⑩側層ᶲ䘬姕⁁柵⭂≇䌯ˤ
ɀ 婳⍫侫䓊⑩✳抬ㆾ㗗⼑䙺ᶲ䘬ἄ㤕㹓⹎ˤ
ɀ 䓊⑩㰺㚱㕟暣墅伖ㆾ侭㍉䓐暣㸸䶂䘬㍺柕夾䁢㕟暣墅伖䘬ᶨ悐↮炻ẍᶳ嬎婆⮯怑䓐 ;
.!⮵㯠忋㍍姕⁁炻 ⛐姕⁁⢾悐枰⬱墅⎗妠⍲㕟暣墅伖烊
.!⮵㍺㍍⺷姕⁁炻 ㍺⹏⽭枰㍍役⬱墅⛘溆侴ᶼ㗗㖻㕤妠⍲䘬ˤ
About the Symbols
Various symbols are used in this product to ensure correct usage, to prevent danger to the user and others, and to prevent property damage.
The meaning of these symbols are described below. It is important that you read these descriptions thoroughly and fully understand the
contents.
Appendix C Legal Information
WAH7706 User’s Guide
95
Explanation of the Symbols
Viewing Certifications
Go to http://www.zyxel.com to view this product’s documentation and certifications.
Zyxel Limited Warranty
Zyxel warrants to the original end user (purchaser) that this product is free from any defects in material or workmanship for a specific period (the
Warranty Period) from the date of purchase. The Warranty Period varies by region. Check with your vendor and/or the authorized Zyxel local
distributor for details about the Warranty Period of this product. During the warranty period, and upon proof of purchase, should the product
have indications of failure due to faulty workmanship and/or materials, Zyxel will, at its discretion, repair or replace the defective products or
components without charge for either parts or labor, and to whatever extent it shall deem necessary to restore the product or components to
proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal or higher value,
and will be solely at the discretion of Zyxel. This warranty shall not apply if the product has been modified, misused, tampered with, damaged by
an act of God, or subjected to abnormal working conditions.
Note
Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This warranty is in lieu of all other warranties,
express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. Zyxel shall in no event be held
liable for indirect or consequential damages of any kind to the purchaser.
To obtain the services of this warranty, contact your vendor. You may also refer to the warranty policy for the region in which you bought the
device at http://www.zyxel.com/web/support_warranty_info.php.
Registration
Register your product online to receive e-mail notices of firmware upgrades and information at www.zyxel.com for global products, or at
www.us.zyxel.com for North American products.
Open Source Licenses
This product contains in part some free software distributed under GPL license terms and/or GPL like licenses. Open source licenses are provided
with the firmware package. You can download the latest firmware at www.zyxel.com. To obtain the source code covered under those Licenses,
please contact support@zyxel.com.tw to get it.
SYMBOL EXPLANATION
Alternating current (AC):
AC is an electric current in which the flow of electric charge periodically reverses direction.
Direct current (DC):
DC if the unidirectional flow or movement of electric charge carriers.
Earth; ground:
A wiring terminal intended for connection of a Protective Earthing Conductor.
Class II equipment:
The method of protection against electric shock in the case of class II equipment is either double insulation or
reinforced insulation.
Index
LTE4506 User’s Guide
96
Index
A
access 12
authentication 40, 42
RADIUS server 42
B
Broadband 25
C
certifications 91
viewing 95
channel, wireless LAN 40
configuration 8
contact information 79
cookies 12
copyright 88
CTS threshold 40
current date/time 71
customer support 79
D
data fragment threshold 40
date 71
disclaimer 88
E
encryption 42
ESSID 77
Extended Service Set IDentification 35
F
filters
MAC address 36, 41
Firefox 12
fragmentation threshold 40
G
General wireless LAN screen 34
H
hardware connections 9
I
installation 8
Internet Explorer 12
IP Address 50
J
Java
permissions 12
JavaScripts 12
L
LEDs 9
limitations
wireless LAN 43
WPS 48
Index
LTE4506 User’s Guide
97
logout
Web Configurator 15
M
MAC address
filter 36, 41
MAC authentication 36
maintenance 8
management 8
managing the device
good habits 9
N
Netscape Navigator 12
O
overview 8
P
PBC 43
PIN, WPS 44
example 45
pop-up windows 12
preamble 40
Push Button Configuration, see PBC
push button, WPS 43
R
RADIUS server 42
RTS threshold 40
S
screen resolution 12
security
wireless LAN 40
Service Set 35
SIM card 9
SSID 41
status 20
supported browsers 12
T
thresholds
data fragment 40
RTS/CTS 40
time 71
U
use 8
W
WAN
Wide Area Network, see WAN 25
warranty 95
note 95
Web Configurator 8, 12
access 12
requirements 12
supported browsers 12
web configurator 8
WEP 42
Wi-Fi 32
wireless channel 77
wireless LAN 32, 39, 77
authentication 40, 42
channel 40
encryption 42
example 39
fragmentation threshold 40
Index
LTE4506 User’s Guide
98
limitations 43
MAC address filter 36, 41
preamble 40
RADIUS server 42
RTS/CTS threshold 40
security 40
SSID 41
WEP 42
WPA 42
WPA-PSK 42
WPS 43, 45
example 46
limitations 48
PIN 44
push button 43
wireless security 77
WPA 42
WPA-PSK 42
WPS 43, 45
example 46
limitations 48
PIN 44
example 45
push button 43