Table of Contents
Zyxel PLA6457 User Manual
Displayed below is the user manual for PLA6457 by Zyxel which is a product in the PowerLine Network Adapters category. This manual has pages.
Related Manuals
Default Login Details
User’s Guide
PLA6457
G.hn Wave 2 Powerline Pass-through Gigabit Ethernet Adapter
Copyright © 2021 Zyxel and/or its affiliates. All Rights Reserved.
Default Network Name G.hn Network
LAN IP Address http://DHCP-assigned
IP
Default Password FLYPIG2400
Version 1.0 Ed. 2, 08/2021
PLA6457 User’s Guide
2
IMPORTANT!
READ CAREFULLY BEFORE USE.
KEEP THIS GUIDE FOR FUTURE REFERENCE.
Screenshots and graphics in this book may differ slightly from what you see due to differences in release
versions or your computer operating system. Every effort has been made to ensure that the information
in this manual is accurate.
Related Documentation
•Quick Start Guide
The Quick Start Guide shows how to connect and set up the PLA in your network.
•More Information
Go to support.zyxel.com to find other information on the PLA.
PLA6457 User’s Guide
3
Document Conventions
Warnings and Notes
These are how warnings and notes are shown in this guide.
Warnings tell you about things that could harm you or your device.
Note: Notes tell you other important information (for example, other things you may need to
configure or helpful tips) or recommendations.
Syntax Conventions
• The PLA6457 in this user’s guide may be referred to as the “PLA” in this guide.
• Product labels, screen names, field labels and field choices are all in bold font.
Icons Used in Figures
Figures in this user guide may use the following generic icons. The PLA icon is not an exact
representation of your device.
PLA Router Laptop Computer
Internet Fax Printer Printer
Desktop Smart TV Set-top Box
Table of Contents
PLA6457 User’s Guide
4
Table of Contents
Document Conventions .................. ........................................ ...................... ......................................3
Table of Contents.................................................................................................................................4
Part I: User’s Guide............................................................................................6
Chapter 1
Introducing the PLA ......................................................................... ....................................................7
1.1 Overview ........................................................................................................................................... 7
1.1.1 G.hn Standard ......................................................................................................................... 8
1.2 LEDs .................................................................................................................................................... 8
1.3 Standby Mode .................................................................................................................................. 9
1.4 Ways to Manage the PLA ................................................................................................................ 9
1.5 Expand Your Network with the PLA ................................................................................................ 9
1.6 Security ............................................................................................................................................ 10
1.6.1 Domain Name ....................................................................................................................... 10
1.6.2 Setting Up Encrypted Pairing ............................................................................................... 10
1.7 Multiple Networks ........................................................................................................................... 11
Chapter 2
RESET and ENCRYPT Buttons................. ...................... ...................... ... ....................... ........................12
2.1 ENCRYPT Button .............................................................................................................................. 12
2.2 Adding Devices to a G.hn Network ............................................................................................. 12
2.3 Multiple Separate G.hn Networks ................................................................................................. 14
2.4 RESET Button .................................................................................................................................... 15
Part II: Technical Reference...........................................................................16
Chapter 3
Web Configurator............................................................................................................... ................17
3.1 Overview ......................................................................................................................................... 17
3.1.1 G.hn Network Security .......................................................................................................... 18
3.2 System Login .................................................................................................................................... 18
3.3 G.hn Settings ................................................................................................................................... 19
3.4 IP Settings ......................................................................................................................................... 20
3.5 Ethernet Settings ............................................................................................................................. 22
Table of Contents
PLA6457 User’s Guide
5
3.6 Device Settings ............................................................................................................................... 23
3.7 Multicast Settings ............................................................................................................................ 25
3.8 Log File Settings ............................................................................................................................... 27
Chapter 4
G.hn Network Setup Tutorial .............................................................................................................29
4.1 Overview ......................................................................................................................................... 29
4.2 Important Terms .............................................................................................................................. 29
4.3 Accessing Your PLA ........................................................................................................................ 29
4.4 Adding a PLA .................................................................................................................................. 30
4.5 Setting Up a New Network with a New PLA ................................................................................ 32
Chapter 5
Troubleshooting..................................................................................................................................34
5.1 Power and Light Problems ............................................................................................................. 34
5.2 Web Configurator Problems .......................................................................................................... 35
5.3 Powerline Problems ........................................................................................................................ 36
5.4 ENCRYPT Button Problems ............................................................................................................. 36
Appendix A Customer Support ....................................................................................................... 38
Appendix B Legal Information ......................................................................................................... 44
Index ...................................................................................................................................................47
6
PART I
User’s Guide
PLA6457 User’s Guide
7
CHAPTER 1
Introducing the PLA
1.1 Overview
This chapter introduces the main applications and features of your Zyxel G.hn Powerline adapter, which
is called “PLA” in this guide.
The PLA plugs into an ordinary power outlet to easily extend a cable or DSL broadband connection or
existing Ethernet (LAN) network to any other electrical outlet in any room of a house, all without the
need for any new cabling. The AC power pass-through feature allows you to unplug electrical device
from a power socket, plug the PLA into the socket and then plug the electrical device back into the
PLA. The power plug varies depending on your region.
In the following diagram, the first PLA (PLA1) connects to an Internet gateway such as a modem and
plugs into an ordinary power outlet. The second PLA (PLA2) plugs into another power outlet and
connects to a computer. PLA1 and PLA2 communicates through ordinary power lines.
Figure 1 PLA Application
Refer to your Quick Start Guide for hardware connection information.
In this User’s Guide the electrical wiring network is referred to as the “G.hn Network”.
Table 1 PLA Features
PORT/FEATURE PLA6457
Number of Gigabit Ethernet ports 1
AC Pass-Through YES
Encrypt Button YES
Reset Button YES
Maximum PHY Rate over Powerline 1200 Mbps
PLA1
PLA2
Chapter 1 Introducing the PLA
PLA6457 User’s Guide
8
1.1.1 G.hn Standard
G.hn is a specification for home networking devices that operates over power lines. G.hn specifies the
point-to-point security inside a domain, which means that each pair of transmitter and receiver uses a
unique encryption key which is not shared by other devices in the same domain. Devices can securely
communicate with each other at high data transfer rates.
The PLA uses 128-bit Advanced Encryption Standard (AES) to ensure safe transfer of information.
1.2 LEDs
The following section describes the lights (LEDs) on the PLA.
The following figure is the front panel of the PLA. Use the lights to determine if the PLA is behaving
normally or if there are some problems on your G.hn Network.
Figure 2 PLA Lights
The following table describes the behavior of the lights on the PLA.
Table 2 LEDs
LIGHTS ICON COLOR STATUS DESCRIPTION
POWER Green On The PLA is on and receiving power.
Blinking The power LED blinks when it is in standby mode that allows you
to save on power during periods of inactivity. Refer to Section 1.3
on page 9 for details on this feature.
Off The PLA is not receiving power.
POWERLINE Green On The PLA detects another PLA and can transmit and/or receive
data at greater than 80 Mbps.
Amber The PLA detects another PLA and can transmit and/or receive
data between 20 – 80 Mbps.
Red The PLA detects another PLA and can transmit and/or receive
data between 0 – 20 Mbps.
Green/
Amber/
Red
Blinking The PLA is communicating with another PLA. Data is being
transmitted and/or received.
Off The PLA does not detect another PLA.
Chapter 1 Introducing the PLA
PLA6457 User’s Guide
9
1.3 Standby Mode
You can set your PLA to save on power when there is no Ethernet connection or activity. Use the Web
Configurator’s Ethernet screen to set the period of time when the PLA will go into standby mode. Refer
to Section 3.5 on page 22 for details on this feature.
The PLA’s power LED blinks signaling that it is going into standby mode. The Ethernet LED, Encrypted
Pairing LED, and Powerline LED are turned off in standby mode.
Note: While in standby mode, you cannot use the RESET and ENCRYPT buttons. To enable the
RESET and ENCRYPT buttons again, you have to connect the PLA’s Ethernet cable to a
computer/notebook or modem/router first. The PLA wakes up from standby mode and
you can start using the RESET and ENCRYPT buttons.
1.4 Ways to Manage the PLA
Use the ENCRYPT button to add PLAs to your G.hn Network. See Chapter 2 on page 12 for instructions on
using the ENCRYPT feature.
Use the Web Configurator to manage the PLA. See Chapter 3 on page 17 for instructions on using the
Web Configurator.
1.5 Expand Your Network with the PLA
Your network can be further expanded by plugging additional PLAs into other outlets in your home and
connecting other computers or network devices (for example, a Smart TV) to them.
ENCRYPTED
PAIRING
Green On It indicates the PLA is connected to another device in encrypted
pairing mode. The transmitter and receiver uses a unique
encryption key for point-to-point security.
Blinking It indicates the PLA is trying to connect with another device in
encrypted pairing mode.
Off Encrypted pairing mode is disabled.
ETHERNET Green On The 10/100/1000 Mbps Ethernet connection is up.
Blinking The PLA is communicating with a networking device connected
to it.
Off The PLA does not detect any devices connected to its ETHERNET
port.
Table 2 LEDs (continued)
LIGHTS ICON COLOR STATUS DESCRIPTION
Chapter 1 Introducing the PLA
PLA6457 User’s Guide
10
Figure 3 Expand Your Network with the PLA
Connect your first PLA (PLA1) to an Internet gateway such as a modem and plug it into an ordinary
power outlet in your home. Plug a second PLA (PLA2) in Room1 into another power outlet and connect
a computer to the PLA for Internet access. Plug a third PLA (PLA3) in Room2 into another power outlet
and connect a Smart TV to the PLA for streaming video. Plug a fourth PLA (PLA4) in Room3 into another
power outlet and connect a Smart TV to the PLA for streaming video.
1.6 Security
Since your G.hn Network may extend outside your premises, it is important to set up security on your PLA.
1.6.1 Domain Name
You can use the domain name to identify your PLA in the G.hn Network.
1.6.2 Setting Up Encrypted Pairing
The ENCRYPT feature automatically sets up encrypted pairing on your G.hn Network using the ENCRYPT
button (see Section 2.1 on page 12 for more information). It involves authenticating the identity of the
two PLAs to be paired and encrypting the link.
Alternatively, use the Web Configurator to set up encrypted pairing on the PLA. Although the PLA is a
“plug-and-play” network expanding solution there are several reasons for enabling security on the G.hn
Network in your home.
1It is easy and only requires you to change a network name.
Table 3 Domain Name Summary
IDENTITY DESCRIPTION
Domain Name Your PLA follow the G.hn standard and is shipped with the same domain name “G.hn
Network”. Change the domain name through the Web Configurator or RESET button to
create a private network. See Section 3.4 on page 20.
Chapter 1 Introducing the PLA
PLA6457 User’s Guide
11
2It is a good idea to ensure privacy of your communication. When you use the PLA and other PLAs, the
electrical wiring in your home becomes an extension of your Ethernet network. Your network traffic flows
freely within the electrical circuit of your home and is bounded in most cases by a power meter.
Without encrypted pairing (security) your information is accessible to anyone using a PLA on the same
electrical circuit. In some cases, a circuit can be shared by more than one household.
To prevent compromising your network security, you can create a private network. A private network
uses a Domain Name to make sure that only permitted PLAs can communicate in your network. See
Section 3.4 on page 20 for information on setting up a private network.
3You may need to change the Domain Name to create multiple G.hn Network. See the next section for
more information on how to set up a multiple network.
1.7 Multiple Networks
Multiple G.hn Networks can coexist on a single electrical circuit. You might want to implement multiple
G.hn Networks in a small office environment where you have two independent Ethernet networks.
1Connect one PLA to a router or switch on the first Ethernet network and assign a Domain Name (for
example “Tom’s Network”) to this PLA (see Section 3.3 on page 19 for more information). Add additional
PLAs to your network by plugging them into your Powerline outlets and assigning them “Tom’s Network”.
This completes the configuration of your first G.hn Network.
2Connect another PLA to a router or switch on the second Ethernet network and assign a different
Domain Name (for example “Alice’s Network”) to this PLA. Again, add additional PLAs and assign them
“Alice’s Network”.
You now have two private networks on your Powerline circuit. Information is not shared between the
two networks as only PLAs with the same criteria for this Domain Name can communicate with each
other.
PLA6457 User’s Guide
12
CHAPTER 2
RESET and ENCRYPT Buttons
2.1 ENCRYPT Button
The ENCRYPT button allows you to set up a secure Powerline connection with other G.hn compliant PLAs
which also support the ENCRYPT feature. No other Powerline setting changes are required to connect.
The following table summarizes the actions that occur when the ENCRYPT button is pressed for specific
lengths of time.
Note: The domain name is unknown when you use the ENCRYPT button.
2.2 Adding Devices to a G.hn Network
You can connect a number of PLAs on a G.hn Network, but you can use the ENCRYPT button on only
two PLAs at a time.
Place a PLA close to another PLA so you have time to set up each one. After you set up the first PLA, you
have 120 seconds to set up the second PLA.
Note: Your PLA must be connected to a networking equipment for the ENCRYPT button to
work. Refer to Section 1.3 on page 9 for more details.
Follow the steps below to set up your G.hn Network:
1Press the ENCRYPT button at the side of your PLA for 2 to 5 seconds. The encrypted pairing ( ) light will
blink as the PLA tries to set up a connection with a new random domain name.
Table 4 ENCRYPT
TIME ACTION ENCRYPTED PAIRING LIGHT
BEHAVIOR POWERLINE LIGHT BEHAVIOR
2 to 5
seconds
Join an existing G.hn Network
by sharing the same network
name as other devices on the
network.
The Encrypted Pairing ( )
light blinks until the device is
connected. This may take a
minute.
The Powerline ( ) light turns
on if your device is connected to
another PLA or a G.hn Network.
Chapter 2 RESET and ENCRYPT Buttons
PLA6457 User’s Guide
13
Figure 4 ENCRYPT Connection Procedure
Note: Check the lights on the two PLAs. The encrypted pairing ( ) and Powerline ( ) lights
should be on while the devices are connecting. Wait for about 2 minutes while your
PLAs connect.
If the encrypted pairing ( ) light does not blink when you press ENCRYPT, you have probably
pressed the ENCRYPT button for too long. Try pressing the ENCRYPT button again for 2 to 5
seconds.
If the Powerline ( ) lights on both PLAs do not light up, the PLAs are not connected. Repeat step
1 in this section. If that does not work, see Troubleshooting in Section 5.4 on page 36 for
suggestions.
2To add more PLAs to your network, use any PLA (A or B) you have connected to set up a connection
with the PLAs you want to connect (C and D).
3Press the ENCRYPT button on both PLAs (A and C, or B and C) for 2 to 5 seconds to add PLA C. This must
be done within 2 minutes (120 seconds) of pressing the ENCRYPT button on the PLA.
4Press the ENCRYPT button on both PLAs (A and D, B and D, or C and D) for 2 to 5 seconds to add PLA D.
This must be done within 2 minutes (120 seconds) of pressing the ENCRYPT button on the PLA.
5After pairing them, unplug the PLAs and plug them where you want to extend your network.
press 2 – 5 seconds
press 2 – 5 seconds
within 2
minutes
PLA PLA
Chapter 2 RESET and ENCRYPT Buttons
PLA6457 User’s Guide
14
Figure 5 Adding More PLAs to Your Network
This sets up your G.hn Network between your PLAs.
2.3 Multiple Separate G.hn Networks
You can use the ENCRYPT button to create multiple separate G.hn Networks by using the ENCRYPT
button on different pairs of PLAs.
1Press the ENCRYPT button on PLAs E and F for 2 to 5 seconds. This must be done within 2 minutes (120
seconds) of pressing the ENCRYPT button on the first PLA.
2Wait for about one minute while PLAs E and F connect.
3Now pair two different PLAs. Press the ENCRYPT button on PLAs G and H for 2 to 5 seconds and within 2
minutes of each other.
4Wait for about one minute while PLAs G and H connect.
5When the encrypted pairing ( ) and Powerline ( ) lights shine steadily, the devices are
connected.
A
B
C
A OR B
D
A OR B OR C
Chapter 2 RESET and ENCRYPT Buttons
PLA6457 User’s Guide
15
Figure 6 Two Separate G.hn Networks
If the Powerline ( ) lights on both PLAs do not light up, the PLAs are not connected. Repeat the
connection process, making certain you press the ENCRYPT buttons for the correct time and
within 2 minutes of each other. If that does not work see Section 5.4 on page 36 for suggestions.
See Troubleshooting in Chapter 5 on page 36 for suggestions on problems with the ENCRYPT button and
the lights.
2.4 RESET Button
The RESET button allows you to reset the PLA to the factory defaults. It also unpairs the PLA from a
network.
The following table summarizes the actions that occur when the RESET button is pressed for specific
lengths of time.
Note: The domain name is unknown when you use the RESET button. You can then pair the
PLA to a different network.
See Troubleshooting in Chapter 5 on page 36 for suggestions on problems with the ENCRYPT button and
the lights.
E
G
F
H
Table 5 RESET
TIME ACTION POWER LIGHT BEHAVIOR POWERLINE LIGHT BEHAVIOR
10 to 15
seconds
Clear all user-entered
configuration information and
return the device to its factory
defaults.
The power ( ) light blinks and
then shines steadily.
The Powerline ( ) light turns
off when it disconnects from the
G.hn Network.
16
PART II
Technical Reference
PLA6457 User’s Guide
17
CHAPTER 3
Web Configurator
3.1 Overview
This chapter shows you how to use the Web Configurator to secure and manage on your G.hn network.
The Web Configurator is an HTML-based management interface that allows easy PLA setup and
management through Internet browser. Use a browser that supports HTML5, such as:
• Microsoft Edge
• Internet Explorer 11 or later
• Google Chrome 34.0.1847.131 or later
• Mozilla Firefox 29.0.1 or later
• Opera 21.0 or later
• Safari 5.1.7 or later
The recommended minimum screen resolution is 1024 by 768 pixels. In order to use the Web Configurator
you need to allow:
• Web browser pop-up windows from your device. Web pop-up blocking is enabled by default in some
browsers.
• JavaScript (enabled by default).
• Java permissions (enabled by default).
The PLA is designed as a plug-and-play network expanding solution. This means that once you
complete your hardware connections, the PLAs in your network (without additional configuration) are
able to communicate with each other by sending and receiving information over your home’s
electrical wiring (A).
Figure 7 Example Network Setup
All G.hn compliant PLAs within range can join your network. The range varies depending on the quality
of your home’s wiring.
A
PLA PLA
Chapter 3 Web Configurator
PLA6457 User’s Guide
18
See Section 3.1.1 on page 18 for more information on enhancing your G.hn network security.
3.1.1 G.hn Network Security
When the PLAs communicate with each other, they use encryption to protect the information that is
sent in the G.hn network. Encryption is like a secret code. If you do not know the secret code, you
cannot understand the message. The G.hn standard uses 128-bit AES (Advanced Encryption Standard)
to safely transmit data between PLAs.
For the PLAs to communicate with each other they all need to use the same network name (or Domain
Name). This network name allows the PLAs to understand the encrypted information sent in the G.hn
network.
By default the PLAs are all configured with the network name G.hn, this allows you to simply plug the
devices in and not worry about setting up security. If you want to enhance the security on your G.hn
network, you can change the network name on the PLAs you want to allow to communicate in your
G.hn network.
3.2 System Login
1Make sure your PLA hardware is properly connected to a router with DHCP server (refer to the Quick
Start Guide). Note down the DHCP-assigned IP address for your PLA.
2Start your web browser.
3The PLA is a DHCP client by default. Type “http://DHCP-assigned IP address” in the Location or Address
field. Press [ENTER]. Your computer must be in the same subnet in order to access this website address.
4The following screen appears.
Figure 8 Web Configurator: Login
5Enter the default password as shown on the cover page. Click Ok to log into the Web Configurator to
manage the PLA directly.
Chapter 3 Web Configurator
PLA6457 User’s Guide
19
3.3 G.hn Settings
Your PLA conforms to the G.hn (G.hn) standard for sending data over electrical power wiring in your
home. Use the G.hn screen to change the basic settings of the PLA. Click G.hn to access this screen.
Figure 9 G.hn Screen
The following table describes the labels in this screen.
Table 6 G.hn Screen
LABEL DESCRIPTION
Basic Settings
MAC address This field displays the MAC address of your PLA. The MAC address of your PLA can be found by
looking at the label on your device. It consists of six pairs of hexadecimal characters
(hexadecimal characters are “0 – 9” and “a – f”). In the case of the PLA, this label is on the back
of the device.
Device ID Every PLA acts as the DOMAIN_MASTER by default before connecting to another PLA. The
default Device ID is 1.
After you press the ENCRYPT button to connect your PLA to another PLA, the two PLAs will
determine which one acts as the DOMAIN_MASTER. This field displays 1 when your PLA is the
DOMAIN_MASTER. It displays 2 when your PLA is the END_POINT (see the Force node Type field in
this table for more information).
Note: When none of the PLA works as the DOMAIN_MASTER in the network, you can
manually configure your PLA as the END_POINT by selecting END_POINT in the
Force node Type field. The Device ID will be set to 0.
Chapter 3 Web Configurator
PLA6457 User’s Guide
20
3.4 IP Settings
Use the IP screen to enable DHCP, or manually assign an IPv4 or IPv6 address, subnet mask, default
gateway, and DNS server to the PLA.
Domain Name The default domain name of the PLA is “G.hn Network”. The PLAs use the same domain name to
recognize and communicate with each other over the powerline network. If you change the
domain name of one device on the network, it will no longer be recognized as part of that
network.
If you change the domain name, make sure you change the domain name for all of the PLAs
that you want to be part of your powerline network.
The domain name can be from 8 to 64 characters in length, using “A”–”Z”, “a”–”z”, “0”–”9”;
spaces are not allowed.
Force node Type This field forces the PLA to have a particular role (END_POINT or DOMAIN_MASTER).
• Select DOMAIN_MASTER if your PLA connects to a router or AP.
• Select END_POINT if your PLA connects to the end device (for example, computer).
• It is recommended to select the default setting AUTOMATIC for automatic role detection of
the PLA.
Node type Shows the current role of the device based on your selection in the previous field.
Note: Node type change can take some time, click Ok after making any changes in
the Force node Type field. You may need to refresh your webpage.
G.hn profile This field selects the G.hn profile of all PLAs to apply in the G.hn network (PLC 100 MHz MIMO
Boost, PLC 100 MHz Boost).
• Select PLC 100 MHz MIMO Boost (multiple input multiple output) when the PLA connects to a
3-prong electrical socket in your home. Multiple electrical paths between PLAs in the same
G.hn network are available and sending and receiving of data is through all 3 wires (power,
neutral, and ground).
• Select PLC 100 MHz Boost when the PLA connects to a 2-wire electrical socket. A single
electrical path between PLAs in the same G.hn network is available and sending and
receiving of data is through the 2 wires (power and neutral).
Encryption Configuration
Encryption is ENABLED
Pairing password Use this password for authentication. Enter a custom password to manually create a secure
connection with another PLA. The password can be up to 30 alphanumeric and special
characters. Then click Change.
Automatic
configuration
Before connecting, make sure the other PLA is using the same Pairing password. Then click Pair
to allow connection with another PLA in the same power circuit. Wait a few minutes for the
connection, you may need to refresh your webpage to update the status.
Available
Connections
This field list all the available G.hn connection details (remote node Device ID, MAC address,
Phy Tx (Mbps) transmission and Phy Rx (Mbps) reception physical speeds. Phy Tx (Mbps) refers to
how fast information is sent from the selected PLA to this PLA. Phy Rx (Mbps) refers to how fast
information is received from the selected PLA to this PLA.
Table 6 G.hn Screen (continued)
LABEL DESCRIPTION
Chapter 3 Web Configurator
PLA6457 User’s Guide
21
Figure 10 IP Screen
The following table describes the labels in this screen.
Table 7 Configuration Screen
LABEL DESCRIPTION
IPv4 configuration
DHCP enabled Select YES if your PLA is connected to a DHCP-enabled router that can assign it an IPv4 address.
The IPv4 address / netmask, Default Gateway, and DNS fields will be filled automatically when
configuration is received from the DHCPv4 server.
Select NO if you wish to assign an IPv4 Address, Subnet Mask, Default Gateway and DNS to your
PLA.
IPv4 address /
netmask
Enter the IPv4 address and subnet mask you wish to assign to your PLA.
This field is only available when you select No in the DHCP enabled field.
Default
Gateway
Enter the gateway IP address you wish to assign to your PLA.
This field is only available when you select No in the DHCP enabled field.
DNS Enter the IPv4 DNS server address you configure manually.
This field is only available when you select No in the DHCP enabled field.
Click Ok for the changes to take effect.
Note: All changes except the DNS server will only take effect after a system reboot.
IPv6 configuration
DHCP enabled Select YES if your PLA is connected to a DHCP-enabled router that can assign it an IPv6 address.
The IPv6 address / prefix , Default Gateway, and DNS fields will be filled automatically when
configuration is received from the DHCPv6 server.
Select NO if you wish to assign an IPv4 Address, Subnet Mask, Default Gateway and DNS to your
PLA.
Chapter 3 Web Configurator
PLA6457 User’s Guide
22
3.5 Ethernet Settings
Use the Ethernet screen to view information on the PLA’s Ethernet port. as well as set the PLA’s power
saving mode.
Figure 11 Ethernet Screen
The following table describes the labels in this screen.
IPv6 address /
prefix
Enter the IPv6 address you wish to assign to your PLA and the address prefix length to specify
how many most significant bits in an IPv6 address compose the network address.
This field is only available when you select No in the DHCP enabled field.
Default
Gateway
Enter the IP address of the next-hop gateway. The gateway is a router connected to your PLA.
The gateway helps forward packets to their destinations.
This field is only available when you select No in the DHCP enabled field.
DNS Enter the IPv6 DNS server address you configure manually.
This field is only available when you select No in the DHCP enabled field.
IPv6 link-local
address
This field displays the IPv6 link-local address and the network prefix that the PLA generates itself
for the interface.
IPv6 SLAAC
address
This field displays the IPv6 SLAAC (Stateless Address Auto-configuration) IP address and prefix
obtained from an IPv6 router in the network.
Click Ok for the changes to take effect.
Note: All changes except the DNS server will only take effect after a system reboot.
Table 7 Configuration Screen (continued)
LABEL DESCRIPTION
Table 8 Ethernet Screen
LABEL DESCRIPTION
Ethernet
External Interfaces
Interface This shows ETHA and ETHB (PLA’s Ethernet port).
Speed This shows a link rate of 100 Mbps for ETHA, and a link rate of 1000 Mbps for ETHB.
Chapter 3 Web Configurator
PLA6457 User’s Guide
23
3.6 Device Settings
Use the Device screen to view basic system information of the PLA. You can also change the password
for accessing the Web Configurator.
This screen also lets you upload new firmware to your PLA. You can download new firmware releases
from your nearest Zyxel FTP site (or www.zyxel.com) to upgrade your device’s performance. The upload
process uses HTTP (Hypertext Transfer Protocol) and may take up to 2 minutes. After a successful upload,
the PLA will reset.
Duplex This shows the duplex setting (Full or Half). Half duplex cannot send and receive at the same
time. Full duplex can send and receive at the same time.
Interface Type MII (Media Independent Interface) is the interface between the media access control (MAC)
and the PLA.
RGMII (Reduced Gigabit Media Independent Interface) is displayed for the PLA that connects
to a device requiring Internet over Powerline, such as a computer.
SGMII (Serial Gigabit Media Independent Interface) is displayed for the PLA that connects to a
device for Internet access, such as a router.
Mode This shows MAC.
Internal PHY This is the Ethernet’s internal physical layer and will always show No.
Link This shows YES when the PLA has an active connection with a router or computer. Otherwise, it
will show No.
Powersaving
Inactivity
detection mode
Select ETH link to have the selected PLAs go into standby mode when there is no Ethernet
connection.
Select ETH activity to have the selected PLAs go into standby mode when there is no Ethernet
activity detected.
Otherwise, select Disabled to have the PLAs never go into standby mode. The default setting is
Disabled.
Inactivity time(s) Set the period of time (5 to 86,400 seconds) when the PLA will go into standby mode when no
Ethernet connection or activity is detected (based on your selection in the Inactivity detection
mode field).
This field is not available if you select Disabled in the Inactivity detection mode field.
Table 8 Ethernet Screen (continued)
LABEL DESCRIPTION
Chapter 3 Web Configurator
PLA6457 User’s Guide
24
Figure 12 Device Screen
The following table describes the labels in this screen. After you see the firmware updating screen, wait 2
minutes before logging into the PLA again.
Table 9 Device Screen
LABEL DESCRIPTION
Hardware information
Device name This field displays the PLA system name. It is used for identification.
Device
description
This field shows that this is a G.hn bridge PLA.
Device
manufacturer
This field displays the manufacturer of this PLA.
Serial number This field displays the manufacturer assigned number of this PLA.
MAC address This field displays the Ethernet adapter MAC (Media Access Control) address of this PLA.
HW version This field displays the hardware version number of this PLA.
Software information
FW version This field displays the current version of the firmware inside this PLA.
System uptime This field displays how long the PLA has been running since it last started up. The PLA starts up
when you plug it in, or when you reset it.
Security
New
Configuration
password
Type your new Web Configurator password. The password must consist of 6 to 64 characters,
including 0 to 9 and a to z (case sensitive). Note that as you type a password, the screen
displays a (*) for each character you type. Then click Ok. After you change the password, use
the new password to access the PLA.
HTTP SW update
Chapter 3 Web Configurator
PLA6457 User’s Guide
25
Note: The PLA will reset and the Web Configurator will refresh to the Login screen upon
successful installation. It is recommended that you compare the software version shown
on the Web Configurator’s Device page FW version field with the firmware version
installed, to confirm if the installation is successful.
3.7 Multicast Settings
Multicast delivers IP packets to members defined by multicast groups. Membership to these multicast
groups are established using IGMP/MLD.
Internet Group Multicast Protocol (IGMP) is an IPv4 network-layer protocol used to establish membership
in a Multicast group – it is not used to carry user data.
Multicast Listener Discovery (MLD) is an IPv6 network-layer protocol that uses ICMPv6 message types,
rather than IGMP message types. MLDv1 is equivalent to IGMPv2 and MLDv2 is equivalent to IGMPv3.
Use the Multicast screen to configure IGMP/MLD settings.
Upgrade file Type the location of the file you want to upload in this field or click Browse to find it.
Note: Only use firmware for your PLA. Do NOT remove power from the PLA while
firmware upload is in progress!
Browse Click this to find the .bin file you want to upload. Remember that you must decompress
compressed (.zip) files before you can upload them.
Click Ok to begin the upload process. This process may take up to 2 minutes. When the
Download Progress bar reaches 100 %, click Hardware Reset.
Table 9 Device Screen (continued)
LABEL DESCRIPTION
Chapter 3 Web Configurator
PLA6457 User’s Guide
26
Figure 13 Multicast Screen
The following table describes the labels in this screen.
Table 10 Multicast Screen
LABEL DESCRIPTION
Multicast Configuration
IGMP Snooping Select YES to allow the PLA to learn multicast group. Otherwise, select NO to disable it.
MLD Snooping Select YES to allow the PLA to discover the presence of MLD (Multicast Listener Discovery)
members who wish to receive multicast packets. Otherwise, select NO to disable it.
IGMP/MLD
broadcast report
This field is only available when IGMP Snooping is YES.
Select NO to drop IGMP/MLD reports until a multicast member is discovered. Then the reports
are sent to the member.
Select YES to have the PLA send IGMP/MLD reports according to the next field.
IGMP/MLD
broadcast report
mode
This field is only available when IGMP/MLD broadcast report is YES.
• Select 0 to allow the PLA to send IGMP/MLD reports even when the video source is
unknown.
• Select 1 to allow the PLA to always send IGMP/MLD reports.
• Select 2 to allow the PLA to send IGMPv3 IGMP/MLD reports even when the video source is
unknown.
Filter unknown
multicast traffic
Select YES to allow the PLA to listen to multicast traffic on networks defined by multicast groups
only. Otherwise, select NO to disable it.
IGMP Multicast
ranges
Up to 4 multicast IP address ranges can be configured defining the minimum and maximum IP
addresses of each range. Only multicast traffic within these ranges will be processed by the
PLA.
This field is only available when IGMP Snooping is NO.
Click Ok for the changes to take effect.
Chapter 3 Web Configurator
PLA6457 User’s Guide
27
Upon clicking Ok for Broadcast suppression, reboot your PLA by clicking Hardware Reset to make the
changes when the next screen appears.
Figure 14 Hardware Reset
Note: Do NOT click Ok for Factory Reset.
3.8 Log File Settings
Use the Log file screen to allow your PLA to send event logs to an FTP server. You can set the data
capture time interval as well as how often it uploads to the FTP server.
Figure 15 Log File Screen
The following table describes the labels in this screen.
Broadcast suppression
Broadcast xput
limit (Mbps)
Broadcast suppression prevents the Ethernet port from being overloaded by a broadcast storm.
In Broadcast xput limit, set the maximum throughput allowed before suppressing broadcast
traffic. 0 disables broadcast suppression.
Click Ok for the changes to take effect.
Table 10 Multicast Screen (continued)
LABEL DESCRIPTION
Table 11 Log file Screen
LABEL DESCRIPTION
Log File Configuration
Enable Log File Select YES to allow your PLA to send event logs to an FTP server. Otherwise, select NO to disable
it.
Chapter 3 Web Configurator
PLA6457 User’s Guide
28
Data capture
interval(s)
This field allows you to set the time interval (1 – 9,999,999 seconds) to capture data.
FTP server URL This field allows you to set the web address of the remote FTP server where the files (logs) will be
uploaded.
FTP server login This field allows you to set the name for logging in to the FTP server. The login name must contain
1 to 30 characters, including 0 to 9, a to z, and !@#%*()–_+=~,.{}[]\.
FTP server
password
This field allows you to set the password for logging in to the FTP server. The login password must
contain 1 to 30 characters, including 0 to 9, a to z, and !@#%*()–_+=~,.{}[]\.
Upload to server
interval (min)
This field allows you to set the time interval (1 – 9,999,999 minutes) to send the captured data to
the remote server. Enter 0 to disable this function.
Table 11 Log file Screen (continued)
LABEL DESCRIPTION
PLA6457 User’s Guide
29
CHAPTER 4
G.hn Network Setup Tutorial
4.1 Overview
Use this tutorial to expand your existing G.hn network.
After setting up your first home network (instructions for that are in the Quick Start Guide for your Zyxel
PLA) you may want to extend the network or create a new one by adding additional PLAs. This tutorial
shows you the following.
• How to start up your new PLA. You need to do this before you can begin the next sections.
• How to make your existing G.hn network bigger by adding new PLAs.
• How to make a new network separate from your existing network with new PLAs.
The tutorial uses the Web Configurator to set up your PLA.
Note: The PLA in this tutorial is an example only. Your PLA may be different.
4.2 Important Terms
4.3 Accessing Your PLA
1Plug the PLA you want to add to your network into a power socket and, if needed, switch the power
socket on.
Figure 16 Plug Your PLA into a Power Socket
2Connect the PLA to your computer.
Domain Name The domain name allows a PLA to connect with other PLAs that have the same domain
name. It provides security for your G.hn network. The domain name uses English letters
or numbers, from 8 to 64 characters long, with no spaces allowed. (See Section 3.3 on
page 19 for more information.)
1
PLA
Chapter 4 G.hn Network Setup Tutorial
PLA6457 User’s Guide
30
3Use a LAN or Ethernet cable (shown below) to connect the LAN or Ethernet port on your adapter to the
same kind of port on your computer.
Figure 17 Connect Your PLA to a Computer
4Open the Web Configurator on your computer. See Section 3.2 on page 18 for how to launch the Web
Configurator.
5You are now ready to extend your G.hn network or set up a second network.
•See Section 4.4 on page 30 to add a new PLA to your network.
•See Section 4.5 on page 32 to set up a second network with your new adapters.
4.4 Adding a PLA
This section shows you how to add a new PLA to expand your existing network.
The figure below shows the family computer with Internet access on a G.hn network. Expand the
network by adding a new PLA connected to a printer.
Figure 18 Add a Printer to Your G.hn Network
2
3
Chapter 4 G.hn Network Setup Tutorial
PLA6457 User’s Guide
31
Note: You do not need to know the domain name of the new adapter to add it to your
network.
1Connect your computer to the PLA you want to add to your network and open the Web Configurator
(see Section 4.3 on page 29).
2Go to the G.hn screen. On this screen in the Device ID field your new PLA should appear as 1 (A). Check
the Device ID 1 adapter’s MAC address (B). It should match the MAC address listed on the label on the
back of your PLA.
Figure 19 Adding a New Adapter
3Type the password for your existing network in the Pairing password field (C). Then click PAIR (D).
4Your new adapter will now have the same Domain Name as your existing network and so has now
joined your existing network.
5Connect the adapter’s Ethernet port to the device’s LAN port to add the device to the network, for
example, your Internet refrigerator in the kitchen.
6Plug the adapter into a power outlet.
7Repeat this procedure for all additional PLAs that you want to add to your existing or new G.hn network.
A
B
C
D
Chapter 4 G.hn Network Setup Tutorial
PLA6457 User’s Guide
32
4.5 Setting Up a New Network with a New PLA
This section shows you how to use your new PLAs to set up a new G.hn network separate to your existing
network.
The figure below shows two G.hn networks in a house. The first network (1) shows the home computer
connected to a printer and access to the Internet. The second network (2) has no Internet access but
with a media adapter such as the Zyxel DMA-1100P you can use your TV to watch movies and play
games which are stored on a computer.
Figure 20 Add New Adapters to Make a Second Network
1Connect your new PLA and open the Web Configurator as shown in Section 4.5 on page 32. The screen
shown below appears.
2Type a Domain Name that is different from the Domain Name for your existing network. Make sure you
use the same new Domain Name for all new adapters you want to add to your new network.
Chapter 4 G.hn Network Setup Tutorial
PLA6457 User’s Guide
33
Figure 21 Making a New Network with the New Adapter
3After you have set up a new network, you are ready to connect each PLA on your new network to
devices, for example, a computer or a games console.
PLA6457 User’s Guide
34
CHAPTER 5
Troubleshooting
This chapter offers some suggestions to solve problems you might encounter.
5.1 Power and Light Problems
The PLA does not turn on. None of the lights turn on.
1Disconnect and re-connect the PLA.
2Remove the PLA from the outlet. Then connect an electrical device that you know works into the same
power outlet. This checks the status of the power outlet.
3If the problem continues, contact the vendor.
The ETHERNET light does not turn on.
1Check the hardware connections. See the Quick Start Guide.
2Inspect your cables for damage. Contact the vendor to replace any damaged cables.
3Check the Ethernet adapter on your computer and make sure it is enabled and working properly.
4If the PLA is connected to an Ethernet switch or router, make sure the device is working correctly, and
that the LAN network is working and configured correctly as well.
The Powerline light does not turn on.
1Make sure the adapter is plugged in to a power socket and the power socket is turned on.
2Use the Web Configurator to detect all other PLAs on your G.hn Network. Make sure that the domain
name (sometimes called the network password) is the same on all of your PLAs. See Section 3.4 on page
20 for instructions on changing the network name.
3Check the MAC address for all PLAs are shown correctly in the Web Configurator. See Section 3.6 on
page 23 for instructions on checking the MAC address.
Chapter 5 Troubleshooting
PLA6457 User’s Guide
35
4Make sure that all your PLAs are G.hn compliant. Check the package it came in or ask your vendor. This
PLA cannot detect earlier versions of G.hn PLAs such as G.hn 1.0 or 1.0.1. (Although they can coexist on
the same electrical wiring without interfering with each other.)
5Make sure that the PLAs on your network are all on the same electrical wiring. Connect another PLA into
an outlet close to your PLA’s power outlet. They are probably now on the same electrical wiring. Check
the Powerline () light. If it now lights up your PLA was probably previously on separate electrical
wiring. Ask an electrician for more information on the electrical wiring in your building.
6Make sure that you do not have a power meter between PLAs. Powerline signals cannot pass this.
The Power and Powerline light blink at the same time indicating an error in pairing.
You have pressed the ENCRYPT button for more than 5 seconds. Try setting up a connection again, this
time pressing the ENCRYPT buttons on both devices for less than 5 seconds.
5.2 Web Configurator Problems
The Web Configurator does not display all or any of my devices.
Inspect the LEDs on your PLA and make sure that the ETHERNET and Powerline LEDs are on or blinking.
See Section 1.2 on page 8 for troubleshooting LED related problems.
I don’t know the IP address of the PLA.
There is no default fixed management IP address for the PLA. You need to log into your router to see the
IP address the router gave to the PLA.
Follow this procedure if you cannot log into the router to see the assigned IP address.
1Connect your PLA to your router’s LAN port using an Ethernet cable.
2Connect the router’s LAN port to your computer’s LAN port using another Ethernet cable.
3Download an IP scanner software, such as Advanced IP Scanner, and use it to scan the IP address used.
The IP address list should include the IP addresses of the router, the PLA, and the computer connected
to the router.
If you want to assign a static IP address to your PLA, please follow the instructions below.
1Type the IP address of the PLA using an Internet browser to log into the PLA’s Web Configurator. After
logging into the Web Configurator, go to the IP screen.
Chapter 5 Troubleshooting
PLA6457 User’s Guide
36
2Under IPv4 Configuration, disable DHCP enable and then assign an IP in the IPv4 address field as the
static IP. You can now use this IP address as the default IP address to log into the PLA’s Web
Configurator.
Note: The static IP must be in the same subnet of the router.
5.3 Powerline Problems
The signal on my G.hn Network is weak.
1Your PLAs cannot be connected to extension cords. Connect them to standard power outlets.
2Your PLAs may be located close to large appliances such as refrigerators or air-conditioners that cause
interference with the Powerline signal. Move the adapters further away from such appliances to reduce
interference.
3Your PLAs may be placed close to electrical devices such as electrical insect-killers which produce radio
waves. These may interfere with the Powerline signals. Move the adapters further away from such
electrical devices.
4Your wiring may be old and/or low quality or with a long wiring path.
5.4 ENCRYPT Button Problems
The Power light does not blink when I press the ENCRYPT button.
• Check that the device is on.
• Press the ENCRYPT button again, making certain you have pressed the button for 2 to 5 seconds.
• For PLA, you cannot use the ENCRYPT button when it is in standby mode. Connect the PLA to a
computer or router, then try again.
The Power lights on both devices blink when I press the ENCRYPT buttons, but the Powerline light
does not turn on.
• Ensure you have pressed the ENCRYPT buttons on both devices.
• Wait for about a minute while the devices set up a connection.
• If that does not work, try again with both devices connected to a power strip next to each other. If
they now connect, then the devices were not on the same electrical circuit before.
Chapter 5 Troubleshooting
PLA6457 User’s Guide
37
The Power lights on both devices blink, then the Powerline light blinks red.
Do not worry, the connection process is proceeding normally.
The Power lights on both devices finished blinking, but only one device’s Powerline light is on.
One device may have connected to a third PLA. To check if device A is connected to device B and not
to device C, disconnect device B from its power source. Device A’s Powerline () light will turn off if
the connection is with device B and stay on if it is with device C. Disconnect device A from device C by
pressing the RESET button on device C for 10 – 15 seconds. And then reconnect device A to device B by
pressing the ENCRYPT button for 2 to 5 seconds on both devices within 120 seconds.
PLA6457 User’s Guide
38
APPENDIX A
Customer Support
In the event of problems that cannot be solved by using this manual, you should contact your vendor. If
you cannot contact your vendor, then contact a Zyxel office for the region in which you bought the
device.
See https://www.zyxel.com/homepage.shtml and also
https://www.zyxel.com/about_zyxel/zyxel_worldwide.shtml for the latest information.
Please have the following information ready when you contact an office.
Required Information
• Product model and serial number.
• Warranty Information.
• Date that you received your device.
• Brief description of the problem and the steps you took to solve it.
Corporate Headquarters (Worldwide)
Taiwan
• Zyxel Communications Corporation
• https://www.zyxel.com
Asia
China
• Zyxel Communications (Shanghai) Corp.
Zyxel Communications (Beijing) Corp.
Zyxel Communications (Tianjin) Corp.
• https://www.zyxel.com/cn/zh/
India
•Zyxel Technology India Pvt Ltd.
• https://www.zyxel.com/in/en/
Kazakhstan
•Zyxel Kazakhstan
• https://www.zyxel.kz
Appendix A Customer Support
PLA6457 User’s Guide
39
Korea
• Zyxel Korea Corp.
• http://www.zyxel.kr
Malaysia
• Zyxel Malaysia Sdn Bhd.
• http://www.zyxel.com.my
Pakistan
• Zyxel Pakistan (Pvt.) Ltd.
• http://www.zyxel.com.pk
Philippines
• Zyxel Philippines
• http://www.zyxel.com.ph
Singapore
• Zyxel Singapore Pte Ltd.
• http://www.zyxel.com.sg
Taiwan
• Zyxel Communications Corporation
• https://www.zyxel.com/tw/zh/
Thailand
• Zyxel Thailand Co., Ltd.
• https://www.zyxel.com/th/th/
Vietnam
• Zyxel Communications Corporation – Vietnam Office
• https://www.zyxel.com/vn/vi
Europe
Belarus
•Zyxel BY
• https://www.zyxel.by
Belgium
• Zyxel Communications B.V.
• https://www.zyxel.com/be/nl/
Appendix A Customer Support
PLA6457 User’s Guide
40
• https://www.zyxel.com/be/fr/
Bulgaria
•Zyxel България
• https://www.zyxel.com/bg/bg/
Czech Republic
• Zyxel Communications Czech s.r.o
• https://www.zyxel.com/cz/cs/
Denmark
• Zyxel Communications A/S
• https://www.zyxel.com/dk/da/
Estonia
• Zyxel Estonia
• https://www.zyxel.com/ee/et/
Finland
• Zyxel Communications
• https://www.zyxel.com/fi/fi/
France
•Zyxel France
• https://www.zyxel.fr
Germany
•Zyxel Deutschland GmbH
• https://www.zyxel.com/de/de/
Hungary
• Zyxel Hungary & SEE
• https://www.zyxel.com/hu/hu/
Italy
• Zyxel Communications Italy
• https://www.zyxel.com/it/it/
Latvia
•Zyxel Latvia
• https://www.zyxel.com/lv/lv/
Appendix A Customer Support
PLA6457 User’s Guide
41
Lithuania
•Zyxel Lithuania
• https://www.zyxel.com/lt/lt/
Netherlands
• Zyxel Benelux
• https://www.zyxel.com/nl/nl/
Norway
• Zyxel Communications
• https://www.zyxel.com/no/no/
Poland
• Zyxel Communications Poland
• https://www.zyxel.com/pl/pl/
Romania
• Zyxel Romania
• https://www.zyxel.com/ro/ro
Russia
• Zyxel Russia
• https://www.zyxel.com/ru/ru/
Slovakia
• Zyxel Communications Czech s.r.o. organizacna zlozka
• https://www.zyxel.com/sk/sk/
Spain
• Zyxel Communications ES Ltd.
• https://www.zyxel.com/es/es/
Sweden
• Zyxel Communications
• https://www.zyxel.com/se/sv/
Switzerland
•Studerus AG
• https://www.zyxel.ch/de
• https://www.zyxel.ch/fr
Appendix A Customer Support
PLA6457 User’s Guide
42
Turkey
• Zyxel Turkey A.S.
• https://www.zyxel.com/tr/tr/
UK
• Zyxel Communications UK Ltd.
• https://www.zyxel.com/uk/en/
Ukraine
•Zyxel Ukraine
• http://www.ua.zyxel.com
South America
Argentina
• Zyxel Communications Corporation
• https://www.zyxel.com/co/es/
Brazil
• Zyxel Communications Brasil Ltda.
• https://www.zyxel.com/br/pt/
Colombia
• Zyxel Communications Corporation
• https://www.zyxel.com/co/es/
Ecuador
• Zyxel Communications Corporation
• https://www.zyxel.com/co/es/
South America
• Zyxel Communications Corporation
• https://www.zyxel.com/co/es/
Middle East
Israel
• Zyxel Communications Corporation
• http://il.zyxel.com/
Appendix A Customer Support
PLA6457 User’s Guide
43
Middle East
• Zyxel Communications Corporation
• https://www.zyxel.com/me/en/
North America
USA
• Zyxel Communications, Inc. – North America Headquarters
• https://www.zyxel.com/us/en/
Oceania
Australia
• Zyxel Communications Corporation
• https://www.zyxel.com/au/en/
Africa
South Africa
• Nology (Pty) Ltd.
• https://www.zyxel.com/za/en/
PLA6457 User’s Guide
44
APPENDIX B
Legal Information
Copyright
Copyright © 2021 by Zyxel and/or its affiliates.
The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any
language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or
otherwise, without the prior written permission of Zyxel and/or its affiliates.
Published by Zyxel and/or its affiliates. All rights reserved.
Disclaimer
Zyxel does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any
license under its patent rights nor the patent rights of others. Zyxel further reserves the right to make changes in any products described herein
without notice. This publication is subject to change without notice.
Regulatory Notice and Statement
EUROPEA N UNION
The following information applies if you use the product within the European Union.
List of national codes
Safety Warnings
• Do not use this product near water, for example, in a wet basement or near a swimming pool.
• Do not expose your device to dampness, dust or corrosive liquids.
• Do not store things on the device.
COUNTRY ISO 3166 2 LETTER CODE COUNTRY ISO 3166 2 LETTER CODE
Austria AT Liechtenstein LI
Belgium BE Lithuania LT
Bulgaria BG Luxembourg LU
Croatia HR Malta MT
Cyprus CY Netherlands NL
Czech Republic CZ Norway NO
Denmark DK Poland PL
Estonia EE Portugal PT
Finland FI Romania RO
France FR Serbia RS
Germany DE Slovakia SK
Greece GR Slovenia SI
Hungary HU Spain ES
Iceland IS Switzerland CH
Ireland IE Sweden SE
Italy IT Turkey TR
Latvia LV United Kingdom GB
Appendix B Legal Information
PLA6457 User’s Guide
45
• Do not obstruct the device ventilation slots, as insufficient airflow may harm your device. For example, do not place the device in an
enclosed space such as a box or on a very soft surface such as a bed or sofa.
• Do not install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning.
• Connect ONLY suitable accessories to the device.
• Do not open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified
service personnel should service or disassemble this device. Please contact your vendor for further information.
• Make sure to connect the cables to the correct ports.
• Place connecting cables carefully so that no one will step on them or stumble over them.
• Always disconnect all cables from this device before servicing or disassembling.
• Do not remove the plug and connect it to a power outlet by itself; always attach the plug to the power adaptor first before connecting it to
a power outlet.
• Do not allow anything to rest on the power adaptor or cord and do NOT place the product where anyone can walk on the power adaptor
or cord.
• Please use the provided or designated connection cables/power cables/ adaptors. Connect it to the right supply voltage (for example, 110
V AC in North America or 230 V AC in Europe). If the power adaptor or cord is damaged, it might cause electrocution. Remove it from the
device and the power source, repairing the power adapter or cord is prohibited. Contact your local vendor to order a new one.
• Do not use the device outside, and make sure all the connections are indoors. There is a remote risk of electric shock from lightning.
• CAUTION: Risk of explosion if battery is replaced by an incorrect type, dispose of used batteries according to the instruction. Dispose them at
the applicable collection point for the recycling of electrical and electronic devices. For detailed information about recycling of this
product, please contact your local city office, your household waste disposal service or the store where you purchased the product.
• The following warning statements apply, where the disconnect device is not incorporated in the device or where the plug on the power
supply cord is intended to serve as the disconnect device,
– For permanently connected devices, a readily accessible disconnect device shall be incorporated external to the device;
– For pluggable devices, the socket-outlet shall be installed near the device and shall be easily accessible.
Environment Statement
Disposal and Recycling Information
The symbol below means that according to local regulations your product and/or its battery shall be disposed of separately from domestic
waste. If this product is end of life, take it to a recycling station designated by local authorities. At the time of disposal, the separate
collection of your product and/or its battery will help save natural resources and ensure that the environment is sustainable development.
Die folgende Symbol bedeutet, dass Ihr Produkt und/oder seine Batterie gemäß den örtlichen Bestimmungen getrennt vom Hausmüll
entsorgt werden muss. Wenden Sie sich an eine Recyclingstation, wenn dieses Produkt das Ende seiner Lebensdauer erreicht hat. Zum
Zeitpunkt der Entsorgung wird die getrennte Sammlung von Produkt und/oder seiner Batterie dazu beitragen, natürliche Ressourcen zu
sparen und die Umwelt und die menschliche Gesundheit zu schützen.
El símbolo de abajo indica que según las regulaciones locales, su producto y/o su batería deberán depositarse como basura separada de
la doméstica. Cuando este producto alcance el final de su vida útil, llévelo a un punto limpio. Cuando llegue el momento de desechar el
producto, la recogida por separado éste y/o su batería ayudará a salvar los recursos naturales y a proteger la salud humana y
medioambiental.
Le symbole ci-dessous signifie que selon les réglementations locales votre produit et/ou sa batterie doivent être éliminés séparément des
ordures ménagères. Lorsque ce produit atteint sa fin de vie, amenez-le à un centre de recyclage. Au moment de la mise au rebut, la
collecte séparée de votre produit et/ou de sa batterie aidera à économiser les ressources naturelles et protéger l'environnement et la santé
humaine.
Il simbolo sotto significa che secondo i regolamenti locali il vostro prodotto e/o batteria deve essere smaltito separatamente dai rifiuti
domestici. Quando questo prodotto raggiunge la fine della vita di servizio portarlo a una stazione di riciclaggio. Al momento dello
smaltimento, la raccolta separata del vostro prodotto e/o della sua batteria aiuta a risparmiare risorse naturali e a proteggere l'ambiente e
la salute umana.
Symbolen innebär att enligt lokal lagstiftning ska produkten och/eller dess batteri kastas separat från hushållsavfallet. När den här produkten
når slutet av sin livslängd ska du ta den till en återvinningsstation. Vid tiden för kasseringen bidrar du till en bättre miljö och mänsklig hälsa
genom att göra dig av med den på ett återvinningsställe.
About the Symbols
Various symbols are used in this product to ensure correct usage, to prevent danger to the user and others, and to prevent property damage.
The meaning of these symbols are described below. It is important that you read these descriptions thoroughly and fully understand the
contents.
Appendix B Legal Information
PLA6457 User’s Guide
46
Explanation of the Symbols
Viewing Certifications
Go to http://www.zyxel.com to view this product’s documentation and certifications.
Zyxel Limited Warranty
Zyxel warrants to the original end user (purchaser) that this product is free from any defects in material or workmanship for a specific period (the
Warranty Period) from the date of purchase. The Warranty Period varies by region. Check with your vendor and/or the authorized Zyxel local
distributor for details about the Warranty Period of this product. During the warranty period, and upon proof of purchase, should the product
have indications of failure due to faulty workmanship and/or materials, Zyxel will, at its discretion, repair or replace the defective products or
components without charge for either parts or labor, and to whatever extent it shall deem necessary to restore the product or components to
proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal or higher value,
and will be solely at the discretion of Zyxel. This warranty shall not apply if the product has been modified, misused, tampered with, damaged by
an act of God, or subjected to abnormal working conditions.
Note
Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This warranty is in lieu of all other warranties,
express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. Zyxel shall in no event be held
liable for indirect or consequential damages of any kind to the purchaser.
To obtain the services of this warranty, contact your vendor. You may also refer to the warranty policy for the region in which you bought the
device at http://www.zyxel.com/web/support_warranty_info.php.
Registration
Register your product online at www.zyxel.com to receive email notices of firmware upgrades and related information.
Open Source Licenses
This product may contain in part some free software distributed under GPL license terms and/or GPL-like licenses.
To request the source code covered under these licenses, please go to: https://www.zyxel.com/form/gpl_oss_software_notice.shtml
SYMBOL EXPLANATION
Alternating current (AC):
AC is an electric current in which the flow of electric charge periodically reverses direction.
Direct current (DC):
DC if the unidirectional flow or movement of electric charge carriers.
Earth; ground:
A wiring terminal intended for connection of a Protective Earthing Conductor.
Class II equipment:
The method of protection against electric shock in the case of class II equipment is either double insulation
or reinforced insulation.
Index
PLA6457 User’s Guide
47
Index
A
AC pass-through 7
accessing the PLA 29
add
new adapter 31
PLA 30
Advanced Encryption Standard, see AES 8
AES 17
AES (Advanced Encryption Standard) 8
B
broadcast suppression 27
maximum amount allowed 27
C
certifications 44
viewing 46
configuration screen 23, 25
connect to computer 29
connections overview 10
contact information 38
copyright 44
customer support 38
D
data capture interval 28
device ID 19
device name 24
Device screen 23
DHCP client 18
DHCP-enabled router 21
disclaimer 44
DNS 21
Domain Name 31
security 11
domain name 10, 31
criteria 29
default 20
HomeGrid 10
unknown 12, 15
duplex setting 23
E
electrical circuit boundaries 17
ENCRYPT button 7, 9, 10, 14
manage 9
overview 12
problem 36
working requirement 12
ENCRYPT connection procedure 13
ENCRYPT feature 10, 12
encrypted pairing
setting up 10
encrypted pairing LED behavior 12
encryption 8, 17
Encryption configuration 20
Ethernet activity
no detection 23
Ethernet connection
inactivity 23
Ethernet port
number of 7
Ethernet screen 22
expand the network 9
Index
PLA6457 User’s Guide
48
F
firmware upgrade 25
firmware version 24
FTP server 28
FTP server password 28
Full duplex 23
G
G.hn 7
G.hn network 7
join 12
setup 12
G.hn profile 20
G.hn screen 19
G.hn standard 10
gateway IP address
PLA 21
H
Half duplex 23
hardware information
PLA 24
hardware reset 27
I
IGMP 25
IGMP Multicast range 26
IGMP snooping 26
IGMP/MLD 25
IGMP/MLD broadcast report 26
mode 26
IGMPv2 25
IGMPv3 25
inactivity detection mode 23
inactivity time
detection 23
Internet Group Multicast Protocol (IGMP) 25
introduction 7
IP packets 25
IP screen 20
IPv4 address 21
IPv6 address 22
IPv6 configuration 21
J
Java permission 17
JavaScript 17
L
LED 34
ENCRYPTED PAIRING 9
ETHERNET 9
POWER 8
POWERLINE 8
LEDs 8
legal information 44
limited warranty 46
local vs. remote adapter 22, 26, 27
Log File screen 27
login
Web Configurator 18
M
MAC address 22, 24, 26, 27
Ethernet adapter 24
PLA 19
manage the PLA 9
management
multiple networks 11
overview 17
managing the device
MIMO (multiple input multiple output) channel 20
MLD 25
MLD snooping 26
MLDv2 25
Index
PLA6457 User’s Guide
49
Multicast configuration 26
multicast group 25
Multicast Listener Discovery (MLD) 25
Multicast screen 25
Multicast settings 25
multiple Powerline networks 11
N
network
add more PLAs 14
network example 17
network information 19
network name
change 10
HomeGrid 18
network security
prevent compromising 11
network setup
example 17
new network setup 32
P
pass-through 7
password 24
for pairing 31
FTP server 28
Web Configurator 24
passwords 22, 26, 27
PHY
internal 23
PHY rate
maximum 7
PLA
add to network 13
plug-and-play 17
power and light
problem 34
power LED behavior 15
power pass-through 7
power saving 23
power saving mode 9
setup 22
Powerline
problem 36
Powerline circuit 11
Powerline LED behavior 12, 15
Powerline network
add devices 12
create multiple networks 14
priority settings 25, 27
private network 10
problem
ENCRYPT button 36
power and light 34
Powerline 36
Web Configurator 35
problems and solutions 34
R
receive rate 19
Regulatory Notice and Statement 44
reset
PLA 25
RESET button 7, 9, 10
overview 15
reset PLA 27
S
safety warnings 44
security 10, 11, 18
passwords 10
serial number
PLA 24
software information 24
standby mode 9
subnet mask
PLA 21
T
time interval
Index
PLA6457 User’s Guide
50
data capture 28
upload to server 28
transfer rates 8
transmit rate 19
troubleshooting 34
tutorial
expand existing Powerline network 29
U
upload to server interval 28
uptime
PLA 24
W
warranty 46
note 46
web browser pop-up window 17
Web Configurator 17, 24
password 24
problem 35
recommended screen resolution 17
supported web browsers 17