Zyxel SFP-BX1310-E User Manual
Displayed below is the user manual for SFP-BX1310-E by Zyxel which is a product in the Network Transceiver Modules category. This manual has pages.
Related Manuals
SFP and SFP+ Transceivers
User’s Guide
EN
1
EN
Removing Fiber-optic Cable
1
Attach an ESD preventive wrist strap to your
wrist and to a bare metal surface on the chassis.
Disconnect all fiber-optic cables from the
SFP/SFP+ module.
1
2
EN
Installing a Module
1
Attach an ESD preventive wrist strap to your
wrist and to a bare metal surface.
Remove the module from its protective packag-
ing.
Locate the transmit (Tx) and the receive (Rx)
markings on the module.
Align the module in front of the slot opening on a
device.
Make sure the latch is in the lock position, then
insert the module into the slot until the module
snaps into place.
Note : Module installation orientation varies
depending on your device. Your module comes
with a mechanism that prevents incorrect
insertion. Do NOT force or twist the module into a
slot.
1
2
3
4
5
EN
Connecting a Fiber-optic Cable
2
Remove the dust plugs from the module and
cables.
Identify the signal transmission direction of the
fiber-optic cable and the module. Insert one end
of the fiber-optic cable into the module.
Insert the other end of the fiber-optic cable into a
remote device.
Note : Refer to the user’s guide that comes with
your device for module slot status.
1
2
3
EN
Introduction
Copyright © 2020 Zyxel Communications Corp. All Rights Reserved.
EU Importer
Zyxel Communications A/S
Gladsaxevej 378, 2. th. 2860 Søborg, Denmark
https://www.zyxel.com/dk/da/
US Importer
Zyxel Communications, Inc
1130 North Miller Street Anaheim, CA 92806-2001
https://www.zyxel.com/us/en/
Removing a Module
3
Unlocking a Module
2
Pull out the latch and down to unlock a module. Pull the latch, or use your thumb and index finger
to grasp the tabs on both sides of the module,
and carefully slide it out of the slot.
Note : Do NOT force or twist the module out of a
slot. If the module will not slide out, grasp the
tabs on both sides of the module with a slight
up/down motion and carefully slide it out of the
slot. If unsuccessful, contact Zyxel Support to
prevent damage to your Zyxel Device and
module.
Insert the dust plug into the ports on a module.
1
2
EN
Use a transceiver module for connection to a remote device. SFP
and SFP+ transceiver modules are hot swappable. You can install
and remove a module while your device is operating.
SFP/SFP+ modules both use 3.3V power input and LC-type
connectors.
SFP/SFP+ modules support data rate of 100M/1G/10G bps and
single-mode/multi-mode connection based on its specification.
Handling Warning
All modules are static sensitive. To prevent damage from
electrostatic discharge (ESD), it is recommended you attach an ESD
preventive wrist strap to your wrist and to a bare metal surface
when you install or remove a module.
All modules are dust sensitive. When not in use, always keep the
dust plug on. Avoid getting dust and other contaminant into the
optical bores, as the optics do not work correctly when obstructed
with dust.
Safety Warning
All modules are equipped with a Class 1 laser, which emits invisible
radiation. Read the following safety warnings carefully.
•To avoid possible eye injury, do not look into an operating
fiber-optic module’s connectors.
•Laser radiation is present when the device or system is powered
up.
•Only trained and qualified personnel should be allowed to install or
replace these modules.
Environmental Warnings
•Dispose of your fiber-optic module according to all national laws
and regulations.
...warranty must be validated with the seller's ....
See the Zyxel website for a list of supported transceivers.
Support Information
USA
+ 1 800 255 4101
support@zyxel.com
EU
https://support.zyxel.eu