Table of Contents
- Contents
- Figure 1: Front panel of the AT-AR2010V router 19
- Figure 2: Back panel of the AT-AR2010V router 19
- Figure 3: AT-AR2010V management panel 20
- Figure 4: ETH ports 22
- Figure 5: Power LED 23
- Figure 6: Fault LED 24
- Figure 7: USB LED 25
- Figure 8: ETH1 Port LEDs 25
- Figure 9: ETH2 Port LEDs 27
- Figure 10: Function 1 LED 28
- Figure 11: Function 2 LED 28
- Figure 12: USB port 29
- Figure 13: DC Power Inlet 30
- Figure 14: USB retainer slot 31
- Figure 15: USB retainer 32
- Figure 16: Attaching the USB retainer 32
- Figure 17: Attaching the cable tie 33
- Figure 18: Console port 34
- Figure 19: Reset button 35
- Figure 20: Components of the AT-AR2010V router 42
- Figure 21: Attaching the rubber feet 45
- Figure 22: Orienting the mounting kit 47
- Figure 23: Securing the mounting kit 47
- Figure 24: Rotating the router down to snap it into place 48
- Figure 25: Connecting the Management Cable to the Console Port 50
- Figure 26: Router initialization messages 51
- Figure 27: Router initialization messages (Continued) 52
- Figure 28: RJ-45 Socket Pin Layout (Front View) 62
- Figure 29: Front DC Power Connector 63
- Preface
- Chapter 1: Overview
- Chapter 2: Beginning the Installation
- Chapter 3: Installing the Router and Powering on the Router
- Chapter 4: Cabling the Networking Ports
- Chapter 5: Troubleshooting
- Appendix A: Technical Specifications
Allied Telesis AT-AR2010V-30 User Manual
Displayed below is the user manual for AT-AR2010V-30 by Allied Telesis which is a product in the Hardware Firewalls category. This manual has pages.
Related Manuals
613-002264 Rev A
AT-AR2010V
Installation Guide
AR2010V
12
ETH
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAULT
PWR
FNC1
FNC2
READY
FAULT
RESET
DC 12-24V
Copyright 2015 Allied Telesis, Inc.
All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc.
Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names,
logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners.
Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document without prior
written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for
any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related
to this manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the
possibility of such damages.
3
Electrical Safety and Emissions Standards
This product meets the following standards.
EMC: Not available at present
Electrical Safety: Not available at present
Environmental Compliance: Not available at present
U.S. Federal Communications Commission
Radiated Energy
Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15
of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with this instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void your right to operate
this equipment.
Industry Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Warning: In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.
5
Preface .............................................................................................................................................................................. 11
Document Conventions ..............................................................................................................................................12
Contacting Allied Telesis ............................................................................................................................................ 13
Chapter 1: Overview ......................................................................................................................................................... 15
Features ..................................................................................................................................................................... 16
ETH Ports ............................................................................................................................................................ 16
USB Port .............................................................................................................................................................16
USB Retainer Slot ...............................................................................................................................................16
Reset Button ........................................................................................................................................................ 16
LEDs .................................................................................................................................................................... 16
DC Power Inlet ....................................................................................................................................................16
Kensington Lock Hole .........................................................................................................................................17
Installation Options .............................................................................................................................................. 17
Management Software and Interfaces ................................................................................................................17
Management Methods ......................................................................................................................................... 17
Package Contents ......................................................................................................................................................18
Front and Back Panels ...............................................................................................................................................19
Management Panel ....................................................................................................................................................20
Management Software ...............................................................................................................................................21
ETH Ports ................................................................................................................................................................... 22
LEDs ........................................................................................................................................................................... 23
Power LED ..........................................................................................................................................................23
Fault LED ............................................................................................................................................................24
USB LED ............................................................................................................................................................. 24
ETH1 Port LEDs .................................................................................................................................................. 25
............................................................................................................................................................................ 26
ETH2 Port LEDs .................................................................................................................................................. 27
Function 1 LED .................................................................................................................................................... 28
Function 2 LED .................................................................................................................................................... 28
USB Port ..................................................................................................................................................................... 29
DC Power Inlet ...........................................................................................................................................................30
USB Retainer Slot ......................................................................................................................................................31
Console Port ............................................................................................................................................................... 34
Reset Button ............................................................................................................................................................... 35
Power Supply .............................................................................................................................................................36
Chapter 2: Beginning the Installation ............................................................................................................................. 37
Reviewing Safety Precautions .................................................................................................................................... 38
Choosing a Site for the Routers .................................................................................................................................41
Unpacking the Router ................................................................................................................................................. 42
Chapter 3: Installing the Router and Powering on the Router ..................................................................................... 43
Installing the Router on a Table or Desktop ...............................................................................................................44
Chapter 4: Cabling the Networking Ports ....................................................................................................................... 53
Cabling the Twisted Pair Ports ................................................................................................................................... 54
Chapter 5: Troubleshooting .............................................................................................................................................57
Appendix A: Technical Specifications ........................................................................................................................... 59
Contents
Contents
6
Physical Specifications ................................................................................................................................................59
Environmental Specifications.......................................................................................................................................59
Power Specifications ...................................................................................................................................................61
Certifications................................................................................................................................................................61
RJ-45 Twisted Pair Port Pinouts..................................................................................................................................62
RJ-45 Style Serial Console Port Pinouts .....................................................................................................................63
Front DC Power Connector .........................................................................................................................................63
7
Figure 1: Front panel of the AT-AR2010V router..................................................................................................................19
Figure 2: Back panel of the AT-AR2010V router ..................................................................................................................19
Figure 3: AT-AR2010V management panel..........................................................................................................................20
Figure 4: ETH ports ..............................................................................................................................................................22
Figure 5: Power LED ............................................................................................................................................................23
Figure 6: Fault LED...............................................................................................................................................................24
Figure 7: USB LED ...............................................................................................................................................................25
Figure 8: ETH1 Port LEDs....................................................................................................................................................25
Figure 9: ETH2 Port LEDs....................................................................................................................................................27
Figure 10: Function 1 LED....................................................................................................................................................28
Figure 11: Function 2 LED....................................................................................................................................................28
Figure 12: USB port..............................................................................................................................................................29
Figure 13: DC Power Inlet ....................................................................................................................................................30
Figure 14: USB retainer slot .................................................................................................................................................31
Figure 15: USB retainer........................................................................................................................................................32
Figure 16: Attaching the USB retainer..................................................................................................................................32
Figure 17: Attaching the cable tie .........................................................................................................................................33
Figure 18: Console port ........................................................................................................................................................34
Figure 19: Reset button ........................................................................................................................................................35
Figure 20: Components of the AT-AR2010V router..............................................................................................................42
Figure 21: Attaching the rubber feet .....................................................................................................................................45
Figure 22: Orienting the mounting kit....................................................................................................................................47
Figure 23: Securing the mounting kit....................................................................................................................................47
Figure 24: Rotating the router down to snap it into place .....................................................................................................48
Figure 25: Connecting the Management Cable to the Console Port ....................................................................................50
Figure 26: Router initialization messages.............................................................................................................................51
Figure 27: Router initialization messages (Continued).........................................................................................................52
Figure 28: RJ-45 Socket Pin Layout (Front View) ................................................................................................................62
Figure 29: Front DC Power Connector .................................................................................................................................63
Figures
Figures
8
9
Tables
Table 1: Power LED .............................................................................................................................................................23
Table 2: Fault LED ...............................................................................................................................................................24
Table 3: USB LED ...............................................................................................................................................................25
Table 4: LEDs for ETH1 Port ...............................................................................................................................................26
Table 5: LEDs for ETH2 Port ...............................................................................................................................................27
Table 6: Product Dimension ................................................................................................................................................59
Table 7: Product Weight ......................................................................................................................................................59
Table 8: Environmental Specifications .................................................................................................................................59
Table 9: Maximum Power Consumption ..............................................................................................................................61
Table 10: Input Voltages ......................................................................................................................................................61
Table 11: Product Certifications ...........................................................................................................................................61
Table 12: Pin Signals for 10 and 100 Mbps .........................................................................................................................62
Table 13: Pin Signals for 1000 Mbps ...................................................................................................................................62
Table 14: RJ-45 Style Serial Console Port Pin Signals .......................................................................................................63
Table 15: Front DC Power Connector Pin Signals ..............................................................................................................64
Tables
10
Preface
12
Document Conventions
This document uses the following conventions:
Note
Notes provide additional information.
Caution
Cautions inform you that performing or omitting a specific action
may result in equipment damage or loss of data.
Warning
Warnings inform you that performing or omitting a specific action
may result in bodily injury.
Installation Guide for AT-AR2010V Router
13
Contacting Allied Telesis
If you need assistance with this product, you may contact Allied Telesis
technical support by going to the Support & Services section of the Allied
Telesis web site at www.alliedtelesis.com/support. You can find links for
the following services on this page:
24/7 Online Support — Enter our interactive support center to
search for answers to your product questions in our knowledge
database, to check support tickets, to learn about RMAs, and to
contact Allied Telesis technical experts.
USA and EMEA phone support — Select the phone number that
best fits your location and customer type.
Hardware warranty information — Learn about Allied Telesis
warranties and register your product online.
Replacement Services — Submit a Return Merchandise
Authorization (RMA) request via our interactive support center.
Documentation — View the most recent installation and user
guides, software release notes, white papers, and data sheets for
your products.
Software Downloads — Download the latest software releases for
your managed products.
For sales or corporate information, go to www.alliedtelesis.com/
purchase and select your region.
Preface
14
15
Chapter 1
Overview
This chapter contains the following sections:
“Features” on page 16
“Package Contents” on page 18
“Front and Back Panels” on page 19
“Management Panel” on page 20
“Management Software” on page 21
“ETH Ports” on page 16
“LEDs” on page 23
“USB Port” on page 29
“DC Power Inlet” on page 30
“USB Retainer Slot” on page 31
“Console Port” on page 34
“Reset Button” on page 35
“Power Supply” on page 36
Chapter 1: Overview
16
Features
Here are the features of the AT-AR2010V router.
ETH Ports Here are the basic features of the ETH ports.
Two copper ETH ports for WAN connection
10Base-T (IEEE 802.3i), 100Base-TX (IEEE 802.3u), and
1000Base-T (IEEE 802.3ab) compliant
IEEE 802.3u Auto-Negotiation compliant
Auto-MDI/MDIX
100 meters (328 feet) maximum operating distance
RJ-45 connectors
USB Port Here is the basic feature of the USB port.
Used for maintenance
USB Retainer
Slot Here are the basic features of the USB retainer slot.
Used in conjunction with the USB retainer kit
Used for preventing the USB device from falling out of the router
Reset Button Here are the basic features of the reset button.
Returns to factory default settings
Reboots the router
LEDs Here are the LEDs.
One Power LED
One Fault LED
One USB LED
One Duplex/collision LED and one link/activity LED for the ETH 1
port
One Duplex/collision LED and one link/activity LED for the ETH 2
port
One Function 1 LED
One Function 2 LED
DC Power Inlet Here are the basic features of the DC power inlet.
One DC power inlet on the front panel
Installation Guide for AT-AR2010V Router
17
Supports external DC power supply
One AC Adapter connector on the back panel for external AC
power supply
Kensington Lock
Hole Here are the basic features of the Kensington lock hole.
Used for attaching a lock-and-cable apparatus
One hole located on the center of the back panel
Installation
Options Here are the installation options for the routers.
Desk or tabletop
DIN rail mounting
Management
Software and
Interfaces
Here are the management software and interfaces.
AlliedWare Plus™ Operating System
Command line interface
Management
Methods Here are the methods for managing the routers.
Local management through the Console port
Remote Telnet and Secure Shell management
SNMPv1, v2c, and v3
Chapter 1: Overview
18
Package Contents
1 main unit
1 AC Adapter and regional power cord
1 addendum document sheet
1 USB retainer
1 double-side adhesive tape
2 cable ties
4 stick-on rubber feet kit
1 RS-232 console cable
1 3-Pin DC plug to go with the DC input socket on the front panel
Installation Guide for AT-AR2010V Router
19
Front and Back Panels
The front panel of the AT-AR2010V router is shown in Figure 1.
Figure 1. Front panel of the AT-AR2010V router
The back panel of the AT-AR2010V router is shown in Figure 2.
Figure 2. Back panel of the AT-AR2010V router
AR2010V
12
ETH
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAULT
PWR
FNC1
FNC2
READY
FAULT
RESET
DC 12-24V
12VDC
1.5A MAX
Installation Guide for AT-AR2010V Router
21
Management Software
The routers are shipped with the management software pre-installed. The
software provides a Command Line Interface (CLI) management.
In the unlikely event that the management software becomes corrupted or
damaged on the router, you can download the software from the Allied
Telesis corporate web site and reinstall it on the router. For instructions on
how to install new management software, see the production
documentation.
Chapter 1: Overview
22
ETH Ports
The AT-AR2010V router features two ETH ports for WAN connection. All
ports support 10/100/1000 Mbps twisted pair ports and are 10Base-T,
100Base-TX, and 1000Base-T compliant. You can set the port speeds
and duplex modes either automatically with IEEE 802.3u Auto-Negotiation
or manually with the management software.
The twisted pair ports feature 8-pin RJ-45 connectors. For the port
pinouts, see “RJ-45 Twisted Pair Port Pinouts” on page 62.
The ports have a maximum operating distance of 100 m (328 feet). For 10
Mbps operation, the ports require Category 3 or better 100 ohm shielded
or unshielded twisted pair cabling. For 100 or 1000 Mbps operation, the
ports require Category 5 or Enhanced Category 5 (5e) 100 ohm shielded
or unshielded twisted pair cabling.
Note
A router port connected to an end node that is not using Auto-
Negotiation should not use Auto-Negotiation to set the speed and
duplex mode, because a duplex mode mismatch may occur. In this
case, disable Auto-Negotiation and set the port’s speed and duplex
mode manually.
Figure 4. ETH ports
AR2010V
12
ETH
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAULT
PWR
FNC1
FNC2
READY
FAULT
RESET
DC 12-24V
ETH2 Port
ETH1 Port
Installation Guide for AT-AR2010V Router
23
LEDs
Here are the descriptions of the LEDs.
Power LED The Power LED reports the status of DC power. The LED is shown in
Figure 5.
Figure 5. Power LED
The LED is described in Table 1.
Table 1. Power LED
2
ETH
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAULT
PWR
FNC1
FNC2
READY
FAULT
RESET
DC 12-24V
Power LED
LED State Description
Power Off The router is not receiving DC power or the
internal PSU is not functioning.
Steady
Green The router is receiving DC input power.
Chapter 1: Overview
24
Fault LED The Fault LED reports the status of the router. The LED is shown in Figure
6.
Figure 6. Fault LED
The LED is described in Table 2.
Table 2. Fault LED
USB LED The USB LED reports the status of the USB memory device. The LED is
shown in Figure 7.
2
ETH
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAULT
PWR
FNC1
FNC2
READY
FAULT
RESET
DC 12-24V
Fault LED
LED State Description
Fault Off The router is operating normally.
2 Red Flashes Indicate a power (internal voltage) fault.
6 Red Flashes Indicates a temperature fault.
Steady Red The router is unable to boot.
2
ETH
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAULT
PWR
FNC1
FNC2
READY
FAULT
RESET
DC 12-24V
USB LED
Installation Guide for AT-AR2010V Router
25
Figure 7. USB LED
The LED is described in Table 3.
ETH1 Port LEDs The ETH1 port has two LEDs that display link, activity, duplex and collision
information. The LEDs are shown in Figure 8.
Figure 8. ETH1 Port LEDs
Table 3. USB LED
LED State Description
USB Off No USB memory device is attached.
Steady
Yellow USB memory device is experiencing
failure.
Steady
Green USB memory device is mounted correctly.
AR2010V
12
ETH
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAULT
PWR
FNC1
FNC2
READY
FAULT
RESET
DC 12-24V
ETH1 L/A LED ETH1 D/C LED
Chapter 1: Overview
26
The LEDs are described in Table 4.
Table 4. LEDs for ETH1 Port
LED State Description
Link/
Activity
LED
Solid Green A port has established a 1000 Mbps link to
a network device.
Blinking
Green A port is transmitting or receiving data at
1000 Mbps.
Solid Yellow A port has established a 10 Mbps or 100
Mbps link to a network device.
Blinking
Yellow A port is transmitting or receiving data at 10
or 100 Mbps.
Off A port has not established a link with
another network device.
Duplex
Mode
LED
Solid Green A port is operating in full duplex mode.
Solid Yellow A port is operating in half-duplex mode at 10
or 100 Mbps. (Half-duplex mode does not
apply to 1000 Mbps operation.)
Blinking
Yellow Collisions are occurring on a port operating
at 10 or 100 Mbps.
Off A port has not established a link with
another network device.
Installation Guide for AT-AR2010V Router
27
ETH2 Port LEDs The ETH2 port has two LEDs that display link, activity, duplex and collision
information. The LEDs are shown in Figure 9.
Figure 9. ETH2 Port LEDs
The LEDs are described in Table 4.
Table 5. LEDs for ETH2 Port
AR2010V
12
ETH
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAULT
PWR
FNC1
FNC2
READY
FAULT
RESET
DC 12-24V
ETH2 L/A LED ETH2 D/C LED
LED State Description
Link/
Activity
LED
Solid Green A port has established a 1000 Mbps link to
a network device.
Blinking
Green A port is transmitting or receiving data at
1000 Mbps.
Solid Yellow A port has established a 10 Mbps or 100
Mbps link to a network device.
Blinking
Yellow A port is transmitting or receiving data at 10
or 100 Mbps.
Off A port has not established a link with
another network device.
Duplex
Mode
LED
Solid Green A port is operating in full duplex mode.
Solid Yellow A port is operating in half-duplex mode at 10
or 100 Mbps. (Half-duplex mode does not
apply to 1000 Mbps operation.)
Blinking
Yellow Collisions are occurring on a port operating
at 10 or 100 Mbps.
Chapter 1: Overview
28
Function 1 LED The Function 1 LED is shown in Figure 10. The Function 1 LED is user
configurable and controlled by trigger actions.
Figure 10. Function 1 LED
Function 2 LED The Function 2 LED is shown in Figure 11. The Function 2 LED is user
configurable and controlled by trigger actions.
Figure 11. Function 2 LED
Off A port has not established a link with
another network device.
LED State Description
2
ETH
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAULT
PWR
FNC1
FNC2
READY
FAULT
RESET
DC 12-24V
Function 1 LED
2
ETH
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAULT
PWR
FNC1
FNC2
READY
FAULT
RESET
DC 12-24V
Function 2 LED
Installation Guide for AT-AR2010V Router
29
USB Port
The management panel has a USB port which is shown in Figure 12. You
may also use the port for the following maintenance purposes.
Store configuration files on a USB device and copy the files to
routers whose settings have been lost or corrupted
Update the management firmware on the routers
The USB port is USB2.0 type-A compatible.
Figure 12. USB port
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAULT
PWR
FNC1
FNC2
READY
FAULT
RESET
DC 12-24V
USB Port
Chapter 1: Overview
30
DC Power Inlet
The router has a DC power inlet which is shown in Figure 13. A single 3-
pin power connector is available for DC power input. The front panel
power socket is used when the router is mounted in a DIN rail, or powered
from a building with a centralized12-24V DC feed.
Figure 13. DC Power Inlet
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAULT
PWR
FNC1
FNC2
READY
FAULT
RESET
DC 12-24V
DC Power Inlet
Installation Guide for AT-AR2010V Router
31
USB Retainer Slot
The management panel has a USB retainer slot which is shown in Figure
14. You can use the USB retainer kit and the USB retainer slot to prevent
the USB device from falling out of the USB port.
Note
Cable ties are designed to be used only once. Before you tighten
them make sure they are positioned where you want them.
Figure 14. USB retainer slot
The following steps describe how to use the USB retainer kit and the USB
retainer slot.
1. To fit the shape of the USB device, cut the USB retainer to an
appropriate size and stick the double-side adhesive tape onto the back
of the USB retainer as shown in Figure 15.
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAULT
PWR
FNC1
FNC2
READY
FAULT
RESET
DC 12-24V
USB Retainer Slot
Chapter 1: Overview
32
Figure 15. USB retainer
2. Mount the USB device into the USB port and then attach the H-shaped
tip of the USB retainer to the USB retainer slot as shown in Figure 16.
Figure 16. Attaching the USB retainer
3. Stick the double-side adhesive tape onto the back of the USB retainer.
Wrap the cable tie around the USB device and pass the flat side
through the USB retainer ring. Move the arm into position and the
buckle of the cable tie under the device and tighten the tie.
Double-side adhesive tape
Back of the
USB retainer
Cut to an appropriate size
USB retainer ring
Stick
CONSOLE
FAULT
PWR
FNC1
FNC2
RESET
READY FAUL
T
MASTER STANDBY
FAU LT
PWR
FNC1
FNC2
READY
FAU LT
SET
DC 12-24V
A
ttach the H-shaped tip
to the USB retainer slot
USB device
Installation Guide for AT-AR2010V Router
33
Figure 17. Attaching the cable tie
CONSOLE
FAU LT
PWR
FNC1
FNC2
RESET
READY FAUL
T
MASTER STANDBY
FAU LT
PWR
FNC1
FNC2
READY
FAU LT
SET
DC 12-24V
Cable tie
USB device
Chapter 1: Overview
34
Console Port
The Console port is used to establish a management session with the
router to configure its features and parameter settings. The Console port
is shown in Figure 18. This type of management uses serial RS-232 and is
commonly referred to as local or out-of-band management because it is
not conducted over your network. To perform local management, you
must be at the location of the router and must use the management cable
included with the router.
To establish a local management session with the router, connect a
terminal or a personal computer with a terminal emulation program to the
Console port, which has an RJ-45 style (8P8C) connector, using the
provided management cable. The cable has RJ-45 style (8P8C) and DB-9
(D-sub 9-pin female) connectors.
The Console port is set to the following specifications.
Default baud rate: 9600 bps
Supported baud rate: 9600 bps, 14400 bps, 19200 bps, 28800
bps, 38400 bps, 57600 bps, 115200 bps
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
Note
These settings are for a DEC VT100 or ANSI terminal, or an
equivalent terminal emulation program.
Figure 18. Console port
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAULT
PWR
FNC1
FNC2
READY
FAULT
RESET
DC 12-24V
Console Port
Installation Guide for AT-AR2010V Router
35
Reset Button
The reset button is located between the Console port and the USB port.
You may use the reset button to restore the router to its factory default
settings or reboot the router.
To return to the factory default settings, press and hold the reset
button for at least 5 seconds, and then release the button.
To return to the normal configuration and reboot the router, press
and hold the reset button for at least 1 second but less than 5
seconds, and then release the button.
Note
You won’t lose files that contain user information by rebooting the
router.
Figure 19. Reset button
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAULT
PWR
FNC1
FNC2
READY
FAULT
RESET
DC 12-24V
Reset Button
Chapter 1: Overview
36
Power Supply
A single 4-pin latching type connector is available on the back panel for
power supply. The connector accepts 12V DC power supply. The
connector is not accessible when DIN rail mounting kit is used. The rear
power socket is only used when the router is sitting horizontally on a desk
or table. You can use the power cable and AC power Adapter which are
supplied with the router to power the router from AC mains.
The router also has a DC power inlet on the front panel. A single 3-pin
power connector is available for DC power input. The front panel power
socket is used when the router is mounted in a DIN rail, or powered from a
building with a centralized 12-24V DC feed.
Refer to “Technical Specifications” on page 59 for the input voltage range.
Warning
Power cord is used as a disconnection device. To de-energize
equipment, disconnect the power cord. E3
Chapter 2: Beginning the Installation
38
Reviewing Safety Precautions
Review the following safety precautions before beginning the installation
procedure.
Note
Safety statements that have the symbol are translated into
multiple languages in the T ranslated Safety Statements document at
www.alliedtelesis.com/support.
Warning
Do not work on equipment or cables during periods of lightning
activity. E2
Warning
Power cord is used as a disconnection device. To de-energize
equipment, disconnect the power cord. E3
Note
Pluggable Equipment. The socket outlet shall be installed near the
equipment and shall be easily accessible. E5
Warning
Operating Temperatures. The router is designed for a maximum
ambient temperature of 50° degrees C.
Warning
Hot Surface
Do not touch
Note
All Countries: Install product in accordance with local and National
Electrical Codes. E8
Installation Guide for AT-AR2010V Router
39
Warning
Only trained and qualified personnel are allowed to install or replace
this equipment. E14
Caution
Circuit Overloading: Consideration should be given to the
connection of the equipment to the supply circuit and the effect that
overloading of circuits might have on overcurrent protection and
supply wiring. Appropriate consideration of equipment nameplate
ratings should be used when addressing this concern. E21
Chapter 2: Beginning the Installation
40
Caution
Risk of explosion if battery is replaced by an incorrect type. Replace
only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
Attention: Le remplacement de la batterie par une batterie de type
incorrect peut provoquer un danger d’explosion. La remplacer
uniquement par une batterie du même type ou de type équivalent
recommandée par le constructeur. Les batteries doivent être
éliminées conformément aux instructions du constructeur. E22
Note
Use dedicated power circuits or power conditioners to supply
reliable electrical power to the device. E27
Caution
The unit does not contain serviceable components. Please return
damaged units for servicing. E42
Installation Guide for AT-AR2010V Router
41
Choosing a Site for the Routers
Observe these requirements when planning the installation of the router.
If you plan to install the routers on a table, check to be sure that the
table is level and stable.
The power outlet should be located near the routers and be easily
accessible.
The site should allow for easy access to the ports on the front of
the routers, so that you can easily connect and disconnect cables,
and view the port LEDs.
The site should not expose the routers to moisture or water.
The site should be a dust-free environment.
The site should include dedicated power circuits or power
conditioners to supply reliable electrical power to the network
devices.
Do not install the routers in a wiring or utility box because it will
overheat and fail from inadequate airflow.
Warning
Routers should not be stacked on top of one another on a table or
desktop because that could present a personal safety hazard if you
need to move or replace routers.
Chapter 2: Beginning the Installation
42
Unpacking the Router
Figure 20 lists the items that come with the AT-AR2010V router. If any
item is missing or damaged, contact your Allied Telesis sales
representative for assistance. You should retain the original packaging
material in the event you need to return the unit to Allied Telesis.
cord
Figure 20. Components of the AT-AR2010V router
Four rubber feet
One 2 m (6.6 ft) local management cable with
RJ-45 (8P8C) and DB-9 (D-sub 9-pin female)
connectors.
One double-side adhesive tape
One USB retainer
Two cable ties
One 3-Pin DC plug to go with the
DC input socket on the front panel
One addendum document sheet
REV Description Drawn/Date Initials Checked/Date Initials
A ECO C025999 Oct 2014 AD Oct 2014 WG AT NGFW Device insert
613-002048
613-002048_RevA
A1 OF 1
PRODUCT
TITLE
DWG No
FILE NAME
SCALE
SHEET
SIZE
REV
UNITS
AT NGFW Device insert
1:1
A4
mm
See Installation Guide before connecting the power source.
Product Documentation
Allied Telesis is committed to providing the highest quality products while
minimizing the impact on the environment. As part of our green eco-friendly approach, you
now have access to the latest product documentation at
www.alliedtelesis.com/support.
For a device WITH Local Management Console Port: Connect a terminal
emulator using the management cable provided at either 9600 Baud or 115,200
Baud depending on your product - see your product Installation Guide.
For a device WITHOUT Local Management Console Port: Connect to one
of Ethernet ports and log on with a web browser at http://192.168.1.1/.
LOGIN: In either case, the default User Name is “manager” and default Password
is “friend”.
See Installation Guide before connecting the power source.
Product Documentation
Allied Telesis is committed to providing the highest quality products while
minimizing the impact on the environment. As part of our green eco-friendly approach, you
now have access to the latest product documentation at
www.alliedtelesis.com/support.
For a device WITH Local Management Console Port: Connect a terminal
emulator using the management cable provided at either 9600 Baud or 115,200
Baud depending on your product - see your product Installation Guide.
For a device WITHOUT Local Management Console Port: Connect to one
of Ethernet ports and log on with a web browser at http://192.168.1.1/.
LOGIN: In either case, the default User Name is “manager” and default Password
is “friend”.
See Installation Guide before connecting the power source.
Product Documentation
Allied Telesis is committed to providing the highest quality products while
minimizing the impact on the environment. As part of our green eco-friendly approach, you
now have access to the latest product documentation at
www.alliedtelesis.com/support.
For a device WITH Local Management Console Port: Connect a terminal
emulator using the management cable provided at either 9600 Baud or 115,200
Baud depending on your product - see your product Installation Guide.
For a device WITHOUT Local Management Console Port: Connect to one
of Ethernet ports and log on with a web browser at http://192.168.1.1/.
LOGIN: In either case, the default User Name is “manager” and default Password
is “friend”.
See Installation Guide before connecting the power source.
Product Documentation
Allied Telesis is committed to providing the highest quality products while
minimizing the impact on the environment. As part of our green eco-friendly approach, you
now have access to the latest product documentation at
www.alliedtelesis.com/support.
For a device WITH Local Management Console Port: Connect a terminal
emulator using the management cable provided at either 9600 Baud or 115,200
Baud depending on your product - see your product Installation Guide.
For a device WITHOUT Local Management Console Port: Connect to one
of Ethernet ports and log on with a web browser at http://192.168.1.1/.
LOGIN: In either case, the default User Name is “manager” and default Password
is “friend”.
One AC Adapter and power cord
43
Chapter 3
Installing the Router and Powering on
the Router
The procedures in this chapter are:
“Installing the Router on a Table or Desktop” on page 44
“Fitting Rubber Feet” on page 45
“Installing the Router in a DIN Rail” on page 46
“Connecting DC Power to a Power Supply Module” on page 49
“Starting a Local Management Session” on page 50
“Monitoring the Initialization Processes” on page 51
Chapter 3: Installing the Router and Powering on the Router
44
Installing the Router on a Table or Desktop
You may install the routers on a table or desktop. Here are the guidelines
to selecting a site.
The table should be level and stable.
The power outlet should be located near the routers and be easily
accessible.
The site should allow for easy access to the ports on the front of
the routers, so that you can easily connect and disconnect cables,
and view the port LEDs.
The site should not expose the routers to moisture or water.
The site should be a dust-free environment.
The site should include dedicated power circuits or power
conditioners to supply reliable electrical power to the network
devices.
The rubber feet on the bottom of the routers should be fitted for
table or desktop installation.
Warning
Do not stack routers on top of one another on a table or desktop
because that could present a personal safety hazard if you need to
move or replace routers.
After placing the router on the table or desktop, go to Chapter 4, “Cabling
the Networking Ports” on page 53 to connect the network cables to the
ports on the router.
Installation Guide for AT-AR2010V Router
45
Fitting Rubber Feet
If your routers do not already have rubber feet fitted, fit these as follows:
1. Remove all equipment from the package and store the packaging
material in a safe place.
2. Turn the router over and place it on a table.
3. Remove the adhesive rubber feet from the packaging and press them
firmly onto the base of the router, as shown in Figure 21.
Figure 21. Attaching the rubber feet
4. Turn the router over again and place it on a flat, secure surface (such
as a desk or table) leaving ample space around the unit for ventilation.
AR2010V
12
ETH
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAU LT
PWR
FNC1
FNC2
READY
FAU LT
RESET
DC 12-24V
Chapter 3: Installing the Router and Powering on the Router
46
Installing the Router in a DIN Rail
Observe the following requirements when choosing a DIN rail site for your
router:
The site should allow for easy access to the ports on the front of
the router, so that you can easily connect and disconnect cables,
and view the port LEDs.
The site should allow for adequate air flow around the unit and
through the cooling fins.
The site should not expose the router to moisture or water.
The site should be a dust-free environment.
The site should include dedicated power circuits or power
conditioners to supply reliable electrical power to the network
devices.
Note
The AC Adapter connector on the back panel of the router is not
accessible when the DIN rail mounting kit is used.
Note
DIN rail mounting kits can be purchased separately from your Allied
Telesis dealer.
Warning
Hot surface
Dot not touch
When the router is operating at vertical orientation, the base of the chassis
can be hot.
Here is the procedure for installing the router in a DIN rail.
1. Orient the DIN rail mounting kit against the back panel of the router,
and make sure that the holes align, as shown in Figure 22.
Chapter 3: Installing the Router and Powering on the Router
48
Figure 24. Rotating the router down to snap it into place
4. After snapping the router onto the DIN rail, go to Chapter 4, “Cabling
the Networking Ports” on page 53, to connect the network cables to
the ports on the router.
AR2010V
12
ETH
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAULT
PWR
FNC1
FNC2
READY
FAULT
RESET
DC 12-24V
Installation Guide for AT-AR2010V Router
49
Connecting DC Power to a Power Supply Module
Warning
The router has two power connectors. Only one connector may be
connected to a power source at a time.
To power on the router, perform the following procedure:
1. Join the AC Adapter and power cord and plug the AC Adapter into the
connector on the back panel of the router.
Warning
The power cord is used as a disconnection device. To de-energize
equipment, disconnect the power cord. E3
Note
The connector is not ac cessible when DIN rail mounting kit is used.
The rear power socket is only used when the router is sitting
horizontally on a desk or table.
2. Connect the other end of the power cord to an appropriate AC power
outlet. For power specifications for the router, refer to Appendix A,
“Technical Specifications” on page 59.
3. Verify that the POWER LED is green.
Alternatively, you can power on the router by using the DC power inlet on
the front panel.
Warning
For USA and Canada: The Front or Rear DC input power connector
must be connected to a UL Listed power supply source, marked
“LPS” or “Class 2”
1. Attach the 3-Pin DC plug to the DC power socket and make sure the
two mounting screws are tightened to stop the plug from being pulled
out.
2. Connect the other end of the DC plug to a building with a centralized
12-24V DC feed. For power specifications for the router, refer to
Appendix A, “Technical Specifications” on page 59.
3. Verify that the POWER LED is green.
Chapter 3: Installing the Router and Powering on the Router
50
Starting a Local Management Session
This procedure requires a terminal or a terminal emulator program and the
management cable that comes with the router. To start a local
management session on the router, perform the following procedure:
1. Connect the RJ-45 connector on the management cable to the
Console port on the front panel of the router, as shown in Figure 25.
Figure 25. Connecting the Management Cable to the Console Port
2. Connect the other end of the cable to an RS-232 port on a terminal or
PC with a terminal emulator program.
3. Configure the terminal or terminal emulator program as follows:
Baud rate: 9600 bps (9600 bps, 14400 bps, 19200 bps, 28800 bps,
38400 bps, 57600 bps, 115200 bps. The default is 9600 bps.)
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
Note
The port settings are for a DEC VT100 or ANSI terminal, or an
equivalent terminal emulator program.
CONSOLE
FAU LT
PWR
FNC1
FNC2
RESET
FDX HDX COL
READY FAUL
T
MASTER STANDBY
BYPASSETH1
WAN
2
ETH
CONSOLE
1000 LINK
ACT
100 LINK
ACT
FDX
HDX
COL
FAU LT
PWR
FNC1
FNC2
READY
FAU LT
RESET
DC 12-24V
Installation Guide for AT-AR2010V Router
51
Monitoring the Initialization Processes
It takes about thirty seconds for the router to initialize its management
software programs and features, and load the default configuration.
You may also monitor the bootup sequence by connecting a terminal or
computer that has a terminal emulator program, to the console port on the
router. You will see the messages from Figure 26 below to Figure 27 on
page 52.
Figure 26. Router initialization messages
Starting base/first... [ OK ]
Mounting virtual filesystems... [ OK ]
______________ ____
/\ \ / /______\
/ \ \_ __/ /| ______ |
/ \ | | / | ______ |
/ \ \ / / \ ____ /
/______/\____\ \/ /____________/
Allied Telesis Inc.
AlliedWare Plus (TM) v0.0.0
Current release filename: <release_file_name.rel>
Built: Wed Nov 4 02:32:10 UTC 2015
Mounting static filesystems... [ OK ]
Checking flash filesystem... [ OK ]
Mounting flash filesystem... [ OK ]
Checking for last gasp debug output... [ OK ]
Checking NVS filesystem... [ OK ]
Mounting NVS filesystem... [ OK ]
Starting base/dbus... [ OK ]
Starting base/syslog... [ OK ]
Starting base/loopback... [ OK ]
Starting base/sysctl... [ OK ]
Received event syslog.done
Starting base/reboot-stability... [ OK ]
Checking system reboot stability... [ OK ]
Starting base/cron... [ OK ]
Chapter 3: Installing the Router and Powering on the Router
52
Figure 27. Router initialization messages (Continued)
Checking system reboot stability... [ OK ]
Starting base/cron... [ OK ]
Starting base/appmond... [ OK ]
Starting hardware/openhpi... [ OK ]
Starting hardware/timeout... [ OK ]
Starting base/inet... [ OK ]
Starting base/modules... [ OK ]
Received event modules.done
Received event board.inserted
Received event hardware.done
Starting network/startup... [ OK ]
Starting base/external-media... [ OK ]
Starting network/roboswitch... [ OK ]
Received event network.enabled
Initializing HA processes:
auth, hostd, hsl, irdpd, lacp, loopprot, mstp
nsm, ospf6d, pimd, ripd, ripngd, rmon, tunneld
bgpd, cntrd, imi, ospfd
Received event network.initialized
Received event standalone
Assigning Active Workload to HA processes:
authd, hsl, imi, irdpd, lacpd, loopprotd, mstpd
nsm, ripd, rmond
Received event network.activated
Loading default configuration
Warning: flash:/default.cfg does not exist, loading factory defaults.
..
done!
Received event network.configured
Chapter 4: Cabling the Networking Ports
54
Cabling the Twisted Pair Ports
Here are the guidelines to cabling the 10/100/1000Base-T twisted pair
ports.
The connectors on the cables should fit snugly into the ports, and
the tabs should lock the connectors into place.
The default setting for the wiring configurations of the ports is auto-
MDI/MDI-X. The default setting is appropriate for router ports that
are connected to 10/100Base-TX network devices that also
support auto-MDI/MDI-X.
The default auto-MDI/MDI-X setting is not appropriate for router
ports that are connected to 10/100Base-TX network devices that
do not support auto-MDI/MDI-X and have a fixed wiring
configuration. For router ports connected to those types of network
devices, you should disable auto-MDI/MDI-X and set the wiring
configurations manually.
The appropriate MDI/MDI-X setting for a router port connected to a
10/100Base-TX network device with a fixed wiring configuration
depends on the setting of the network device and whether the
router and network device are connected with straight-through or
crossover cable. If you are using straight-through twisted pair
cable, the wiring configurations of a port on the router and a port
on a network device must be opposite each other, such that one
port uses MDI and the other MDI-X. For example, if a network
device has a fixed wiring configuration of MDI, you must disable
auto-MDI/MDI-X on the corresponding router port and manually set
it to MDI-X. If you are using crossover twisted pair cable, the wiring
configurations of a port on the router and a port on a network
device must be the same.
The default speed setting for the ports is Auto-Negotiation. This
setting is appropriate for ports connected to network devices that
also support Auto-Negotiation.
The default speed setting of Auto-Negotiation is not appropriate for
ports connected to 10/100Base-TX network devices that do not
support Auto-Negotiation and have fixed speeds. For those router
ports, you should disable Auto-Negotiation and set the port’s
speed manually to match the speeds of the network devices.
The 10/100/1000Base-T ports must be set to Auto-Negotiation, the
default setting, to operate at 1000Mbps.
The default duplex mode setting for the ports is Auto-Negotiation.
This setting is appropriate for ports connected to network devices
that also support Auto-Negotiation for duplex modes.
The default duplex mode setting of Auto-Negotiation is not
appropriate for ports connected to network devices that do not
Installation Guide for AT-AR2010V Router
55
support Auto-Negotiation and have a fixed duplex mode. You
should disable Auto-Negotiation on those ports and set their duplex
modes manually to avoid the possibility of duplex mode
mismatches. A router port using Auto-Negotiation defaults to half-
duplex if it detects that the end node is not using Auto-Negotiation,
which can result in a mismatch if the end node is operating at a
fixed duplex mode of full-duplex.
Chapter 4: Cabling the Networking Ports
56
57
Chapter 5
Troubleshooting
This chapter contains suggestions on how to troubleshoot the router if a
problem occurs.
Note
For further assistance, please contact Allied Telesis Technical
Support at www.alliedtelesis.com/support.
Problem 1: The POWER LED on the front of the router is off.
Solutions: The unit is not receiving power. Try the following:
Verify that the power cord is securely connected to the power
source and to the AC Adapter connector on the back panel of the
router.
Verify that the power outlet has power by connecting another
device to it.
Try connecting the unit to another power source.
Try a different power cord.
Verify that the voltage from the power source is within the required
levels for your region.
Problem 2: A twisted pair port on the router is connected to a network
device but the port’s Link/Activity LED is off.
Solutions: The port is unable to establish a link to a network device. Try
the following:
Verify that the network device connected to the twisted pair port is
powered on and is operating properly.
Verify that the twisted pair cable is securely connected to the port
on the media converter channel and to the port on the remote
network device.Verify that the twisted pair cable is securely
connected to the port on the media converter channel and to the
port on the remote network device.
Verify that the port is connected to the correct twisted pair cable.
This is to eliminate the possibility that the port is connected to the
wrong network device, such as a powered off device.
Try connecting another network device to the twisted pair port with
Chapter 5: Troubleshooting
58
a different cable. If the twisted pair port is able to establish a link,
then the problem is with the cable or the other network device.
Verify that the twisted pair cable does not exceed 100 meters (328
feet).
Verify that you are using the appropriate category of twisted pair
cable: Category 3 or better for 10 Mbps operation and Category 5
and Category 5e for 100 and 1000 Mbps operation.
Note
A 1000BASE connection may require five to ten seconds to
establish a link.
Problem 3: Network performance between a twisted pair port on the
router and a network device is slow.
Solutions: There might be a duplex mode mismatch between the port and
the network device. This occurs when a twisted pair port using Auto-
Negotiation is connected to a device with a fixed duplex mode of full
duplex. If this is the cause of the problem, adjust the duplex mode of the
port on the network device or on the router so that both ports are using the
same duplex mode.
Problem 4: A port’s Link/Activity LED is blinking.
Solutions: The link between the port and the network device is
intermittent. Try the following:
Connect another network device with a different cable to the port. If
the Link LED remains steady on, then the problem is with the
original cable or the network device.
59
Appendix A
Technical Specifications
Physical Specifications
Dimensions (Height x Width x Depth)
Weight
Environmental Specifications
Table 6. Product Dimension
AT-AR2010V 42.5 mm x 140 mm x 105mm
(1.7 in. x 5.5 in. x 4.1 in.)
Table 7. Product Weight
AT-AR2010V 556 grams (1.2 lb.)
Table 8. Environmental Specifications
Operating Temperature (horizontal
fanless operation with AC or DC
power)
0° C to 50° C (32° F to 122° F)
Operating Temperature (vertical
fanless operation with AC or DC
power)
0° C to 50° C (32° F to 122° F)
Storage Temperature -20° C to 60° C (-4° F to 140° F)
Operating Humidity 5% to 80% noncondensing
Storage Humidity 5% to 95% noncondensing
Appendix A: Technical Specifications
60
Maximum Operating Altitude 2,000 m (6,562 ft)
You need to de-rate the operating
temperature as altitude increases.
A de-rating of 1° C for every 305 m
(1,000 ft) normally applies.
Maximum Nonoperating Altitude 3,000 m (9,843 ft)
Table 8. Environmental Specifications (Continued)
Installation Guide for AT-AR2010V Router
61
Power Specifications
Maximum Power Consumptions
Input Voltages
Certifications
Table 9. Maximum Power Consumption
DC Power Consumption 13 watts
AC Power Consumption 13 watts
Table 10. Input Voltages
DC Power Consumption 12-24V, 1.5A maximum
AC Power Consumption 12VDC, 1.5A maximum
Table 11. Product Certifications
EMC Not available at present.
Electrical Safety Not available at present.
Environmental Compliance Not available at present.
CE Marking Not available at present.
Appendix A: Technical Specifications
62
RJ-45 Twisted Pair Port Pinouts
Figure 28 illustrates the pin layout of the RJ-45 connectors and ports.
Figure 28. RJ-45 Socket Pin Layout (Front View)
Table 12 on page 62 lists the pin signals for 10 and 100 Mbps.
Table 13 lists the pin signals when a port operating at 1000 Mbps.
Table 12. Pin Signals for 10 and 100 Mbps
Pin MDI Signal MDI-X Signal
1 TX+ RX+
2 TX- RX-
3 RX+ TX+
4 Not used Not used
5 Not used Not used
6 RX- TX-
7 Not used Not used
8 Not used Not used
Table 13. Pin Signals for 1000 Mbps
Pinout Pair
1 Pair 1 +
2 Pair 1 -
3 Pair 2 +
4 Pair 3 +
Installation Guide for AT-AR2010V Router
63
RJ-45 Style Serial Console Port Pinouts
Table 14 lists the pin signals of the RJ-45 style serial Console port.
Front DC Power Connector
Figure 29 illustrates the pin layout of the front DC power connector.
Figure 29. Front DC Power Connector
5 Pair 3 -
6 Pair 2 -
7 Pair 4 +
8 Pair 4 -
Table 13. Pin Signals for 1000 Mbps (Continued)
Table 14. RJ-45 Style Serial Console Port Pin Signals
Pin Signal
1 Looped to pin 8.
2 Looped to pin 7.
3 Transmit Data
4 Ground
5 Ground
6 Receive Data
7 Looped to pin 2.
8 Looped to pin 1.
Pin 1
