APC APCRBC119 User Manual
Displayed below is the user manual for APCRBC119 by APC which is a product in the UPS Batteries category. This manual has pages.
Related Manuals
UXBP
Battery Pack
Models: UXBP24, UXBP24L, UXABP48
• Do not move the UXBP with its batteries installed. Doing so may
result in damage to the Battery Pack and/or a shock hazard.
• Install only factory-authorized batteries in the UXBP. Improper
batteries may result in a hazardous chemical spill and/or a shock
hazard.
3. Presentation
3.1 UXBP front
UXBP Battery Pack
The UXBP contains either two (UXBP24L) or four (UXBP24,
UXABP48) user-replaceable, sealed lead-acid batteries and the associated
cables and connectors.
1. Front panel/Battery door
The front panel of the Battery Pack provides access for battery installation
and replacement. Refer to Section 4 when installing or replacing batteries.
2. Battery internal coupler
These four couplers connect the UXBP’s replaceable internal batteries. See
Section 4.
3. Batteries
The Battery Pack contains either two (UXBP24L) or four (UXBP24,
UXABP48) nominal 12 Vdc sealed lead-acid batteries. Use only factory-
authorized batteries in the UXBP!
3.2 UXBP rear
1. Battery Pack rear panel coupler
Additional UXBP Battery Packs are connected to this coupler. Refer to
Section 4.5 for information on making connections with this coupler.
2. In-line Battery Pack coupler
This coupler connects the Battery Pack to the UPS or to the rear panel
coupler on another matching Battery Pack.
1. Introduction
The UXBP is a large Battery Pack module designed to be used with a Smart-
UPS system to provide a significant increase in on-battery runtime for your
protected equipment.
For complete information on the Smart-UPS system, refer to the Owner’s
Manual that came with your UPS.
Note: If you are installing your Smart-UPS system for the first time, be
sure to read the Smart-UPS Owner’s Manual first. Set up your
UPS system before installing the UXBP.
2. Safety!
CAUTION!
• Use the UXBP only with a UPS that is properly installed according to
the UPS Owner’s Manual and connected only to a two-pole, three-wire
grounding mains receptacle. The receptacle must be connected to
appropriate branch protection (fuse or circuit breaker). Connection to
any other type of receptacle may result in a shock hazard and may
violate local electrical codes.
• Avoid installing the UXBP in locations where there is water or
excessive humidity.
• Do not allow water or any foreign object to get inside the UXBP. Do
not put objects containing liquid on or near the unit.
• To reduce the risk of overheating the UXBP, avoid exposing the unit to
the direct rays of the sun. Avoid installing the unit near heat emitting
appliances such as a room heater or stove.
Installation Instructions
4. Installation
4.1 Receiving inspection
When you remove the UXBP from its shipping container, inspect it for
damage that may have occurred in transit. Immediately notify the carrier and
place of purchase if any damage is found. The packing materials are made
from recyclable materials and should be saved for reuse or disposed of
properly.
4.2 Moving the UXBP
The UXBP and its batteries are quite heavy and should be moved on the
original shipping palette using a fork-type hand truck, or separately on a hand
truck. Never move the Battery Pack while its batteries are installed!
Warning: Do not move the UXBP with its internal batteries installed!
Doing so could result in severe physical damage to the
Battery Pack and cause a shock hazard.
4.3 Placement
The UXBP may be installed in any protected environment that is suitable for
the UPS. Refer to the Owner’s Manual that came with the UPS.
Identify a location convenient to the UPS with enough room in front of and
behind the unit for servicing. There should be at least 30.5 cm (1 ft) clearance
behind the UXBP. Leave enough clearance in front that you can comfortably
access the battery compartment.
Caution: Do not stack more than 4 UXBPs on top of each other or on
top of other components of the UPS system. Damage to the
unit could result.
4.4 Unpacking and Installation
The UXBP is shipped with the cabinet secured to the shipping pallet and its
batteries unconnected. You must unpack the batteries and unbolt the cabinet
from the pallet before you can use your Battery Pack. Use only factory-
authorized batteries in the Battery Pack!
Move the pallet containing the Battery Pack to the desired operating location
before installing the batteries (see Section. 4.3). Do not move the Battery
Pack with the batteries installed!
4.4.1 Warning
It is important that you read and understand the following warnings and
cautions before installing the batteries in the UXBP.
• Only personnel familiar with the dangers of batteries and the required
precautions should perform or supervise battery replacement. Keep
unauthorized personnel away from batteries. Replace batteries with the
same number and type of sealed lead acid batteries as originally installed
in your UXBP.
•WARNING — Use only factory-authorized sealed batteries in the
Battery Pack. Use of unsealed batteries may result in a hazardous
chemical spill.
• CAUTION — Do not dispose of batteries in a fire. The batteries may
explode.
• CAUTION — Do not open or mutilate batteries. They contain an
electrolyte which is toxic and harmful to the skin and eyes.
• CAUTION — A battery can present a risk of electrical shock and high
short circuit current. When replacing batteries, remove wrist watches
and jewelry such as rings. Use tools with insulated handles.
•The batteries in this UPS are recyclable. Dispose of the batteries
properly. The batteries contain lead and pose a hazard to the
environment and human health if not disposed of properly. Refer
to local codes for proper disposal requirements or return the
battery to a factory authorized Service Center.
4.4.2 Unpacking the Battery Pack
To unpack the UXBP, follow the procedure outlined below.
1. Remove the five (5) phillips screws securing the battery door/front
panel to the Battery Pack.
2. Tilt the battery door/front panel forward, then lift it away from the
cabinet.
3. Remove each of the batteries and all corrugated packing material from
inside the cabinet. Remove the corrugated sleeves from the batteries.
Warning! Do not connect the batteries together.
Note: For safety reasons, it is important that all packing material be
removed from the interior of the cabinet.
4. On the outside of the cabinet there are four (4) 1/4-20 screws that secure
the cabinet to the shipping pallet. Use a phillips screwdriver to remove
these four (4) screws.
5. Move the empty cabinet to its permanent location.
6. Proceed to Section 4.4.3, Step 3 to complete the battery installation.
4.4.3 Battery installation and replacement
To install the batteries, follow the procedure outlined below.
1. Remove the five (5) phillips screws securing the battery door/front
panel to the Battery Pack.
2. Tilt the battery door/front panel forward, then lift it away from the
cabinet.
3. Position the batteries on the floor in front of the cabinet. The terminals
should be up and to the inside of the cabinet. Note the gray couplers (4)
located inside the cabinet, one for each battery.
4. Select a battery and, using firm pressure, slide the battery all the way to
the rear of the cabinet.
5. Connect the battery’s coupler to the matching coupler located on the
cabinet wall.
Warning! Do not connect the couplers mounted to the cabinet
together.
6. Select the second battery and move it into place.
UXBP24L - If you have a UXBP24L, place the second battery on the
same side of the cabinet and in front of the first battery.
Note: The batteries may be installed on either side of the cabinet, but
both batteries must be installed on the same side of the cabinet.
UXBP24L
UXBP24 and UXABP48 - If you have a UXBP24 or UXABP48, slide
the second battery all the way to the rear of the cabinet beside the first
battery.
UXBP24 and UXABP48
7. Connect the second battery’s coupler to the matching coupler mounted
on the side of the enclosure and route the battery cable over the top of
the battery.
Warning! Do not connect the batteries together.
8. If you have a UXBP24L, proceed to Section 4.4.4.
If you have a UXBP24 or UXABP48, repeat steps 5 through 7 for the
front battery pair.
9. Refer to Section 4.4.4 for Test Instructions before replacing the
battery door/front panel.
4.4.4 Installing and Replacing Batteries: Test
Instructions
Before coupling the UXBP to a Smart-UPS or another battery pack, a test
must be performed to insure that the batteries have been properly installed
within the cabinet. A DC voltmeter is required to perform this simple test.
Warning! Do not install the UXBP until this test procedure has been
performed.
1. Locate the gray(UXBP24, UXBP24L) or the blue(UXABP48)
coupler at the end of the DC power bus cable (See item 2 in Section
3.2).
2. Measure the DC voltage across the two conductors in the coupler.
W arning! Care must be t aken not to short circuit the coupler with the
test leads.
3. Refer to the following table for the status of the UXBP:
1elbaT
egatloVkcaPyrettaBL42PBXU,42PBXU-
egatloVkcaPyrettaBsutatSkcaPyrettaB
22
.
5
-cdV
82
.
5
cdV llatsnIotydaeR
-cdV0.0
22
.
4
cdV
cdV0.75-cdV6.82
yrettaBdaBroderiwsiM
4. When the Battery Pack Status is “Ready to Install,” complete the final
steps of the installation. If the Battery Pack Status is “Miswired or Bad
Battery,” disconnect the internal battery connections. Do not connect
the UXBP to any other equipment. Review the Installation and Test
Procedures and if necessary contact APC’s Technical Support for
additional help with the installation and troubleshooting. When calls are
placed to the Technical Support Line please have the following
information ready when the representative answers:
1. The UXBP serial number .
2. The battery pack voltage measured at the gray(UXBP24,
UXBP24L) or the blue(UXABP48) coupler.
3. Each of the individual battery voltages.
4.4.5 Final Installation
When the correct battery voltage has been verified, perform the following
steps to complete the battery installation.
1. Replace the battery door/front panel and reinstall the five (5) phillips
screws that were removed in Step 1.
2. Connect the UXBP gray(UXBP24, UXBP24L) or blue(UXABP48)
DC coupler to the UPS or to another matching battery pack (if
desired). This procedure is described in Section 4.5
4.5 Module interconnections
After you have positioned the Battery Pack and installed the batteries, you
can connect the Battery Pack to the UPS or to other Battery Packs in the
system. Refer to the following instructions to properly install the battery pack
couplers.
1. Use a phillips screwdriver to remove the battery pack coupler clamps
from the UPS and from all but the last Battery Pack.
2. Connect the blue battery pack couplers as shown. Do not attempt to
connect the gray(UXBP24, UXBP24L) or the blue(UXABP48) battery
pack couplers with the gray battery couplers inside the cabinet.
Use the supplied UXABP48 adaptor cable when appropriate.
3. Fasten the battery pack coupler clamp to secure the couplers in place.
4. Repeat for any additional Battery Packs.
Installation of the Battery Pack is complete. Refer to the UPS’s Owner’s
Manual for information on starting up the system.
4.6 Estimating Runtime with BackPack.exe
The diskette included with the UXBP contains an MSDOS utility that will
provide the estimated runtime for your configuration at a given load. Follow
the instructions printed on the diskette label, with the following exception:
When the program asks for the number of battery packs installed,
multiply the number of installed UXBP packs by 5 if you have a
UXBP24 or UXABP48, and by 3 if you have a UXBP24L and insert
this result. For example, if you have 2 UXBPs installed, use 10 as the
result ( 2 x 5 = 10).
elbaT
egatloVkcaPyrettaB84PBAXU-2
egatloVkcaPyrettaBsutatSkcaPyrettaB
0.54
-cdV
0.75
cdV llatsnIotydaeR
0.0
cdV0.54-cdV
yrettaBdaBroderiwsiM
5. Storing the Battery Pack
The Battery Pack should be stored in a covered location and with
its batteries in a fully-charged state (reports 100% capacity to the UPS).
In extended storage, use the UPS to refresh the Battery Pack every six
months in environments where the temperature is –15 to +30 °C
(+5 to +86 °F). Refresh the Battery Pack every three months in environments
where the temperature is +30 to +45 °C (+86 to +113 °F).
6. Battery Life
6.1 Battery life
You can expect to receive three to six years of service from the Battery
Pack’s batteries. When the batteries can no longer sustain a charge, the
Replace Battery indicator on the front panel of the UPS lights. Refer to
Section 4 to replace the batteries.
7. Specifications
7.1 Battery
7.2 Environment
990-0191C 04/2007
7.3 Physical
7.4 Runtime versus load
Run times are typical at 25 °C (77 °F).
Run Time
Runtime with SUA1000UXI
Runtime with SUA2200UXI/SUA3000UXI
Recharge Time
T echnical Support and Customer Service
All customers use Web site www .apc.com
American Continent, contact: European Continent, contact:
American Power Conversion American Power Conversion
132 Fairgrounds Road Ballybritt Business Park
West Kingston, Rhode Island 02892 Galway, Ireland
1-800-800-4APC 1-800-702000
1-401-789-5735 353-91-702020
deriuqeremitnuR
daoL ÐÐ
Ð
ÐÐ rh1rh2rh3rh4rh6rh8
AV005 L42PBXU142PBXU1 42PBXU1 +L42PBXU1
AV0001 L42PBXU142PBXU1 +42PBXU1 L
42PBXU1
deriuqeremitnuR
daoL ÐÐ
Ð
ÐÐ rh1rh2rh3rh4rh6rh8
AV005 84PBAXU184PBAXU2
AV0001 84PBAXU184PBAXU284PBAXU3
AV0051 84PBAXU184P
BAXU284PBAXU384PBAXU4
AV0002 84PBAXU184PBAXU284PBAXU384PBAXU484PBAXU5
AV0003 84PBAXU184PBAXU284PBAXU384PBAXU484PBAX
U584PBAXU6
skcaPyrettaBPBXUforebmuN
123456
SPUAV0001 519132721353
SPUAV0022 SPUAV0003 8115.31615.8112
.daolllufdetarfo%05otniegrahcsid
retfayticapac%09otegrahceR*
:epytyrettaB ,42PBXU(ruoFro)L42PBXU(owT ,eerf-ecnanetniam,foorp-llips)84PBAXU dica-daeldelaes
yrettablani
moN :egatlovkcap )L42PBXU,42PBXUledoM(cdV42 )84PBAXUledoM(cdV84
:efilyrettablacipyT tnemnorivnenognidneped
,sraey6ot3 esudna
:emitegrahceR 4.7noitceSnielbateeS
gnitarepO :erutarepmet )F°401+ot23+(C°04+ot0
egarotS :erutarepmet )F°311+ot5+(C°54+ot51–
dnagnitarepO evital
eregarots :ytidimuh
gnisnednoc-non,%59ot0
gnitarepO :noitavele )tf000,01(m000,3ot0
egarotS :noitavele )tf000,
05(m000,51ot0
L42PBXU84PBAXU/42PBXU
:)D´W´H(eziS mc4.57x7.44x0.13 ).ni7.92x6.71x2.21( mc4.57x7.44x0.13 ).ni7.92x6.71x2.21
(
:thgiewPBXU )seirettabhtiw( )sbl0.461(gk5.47)sbl0.082(gk3.721
:thgiewgnippihS )seirettabhtiw( )sbl0.891(gk0.09)sbl0.413(gk7.241