Table of Contents
- Maximum Output Power Capacity
- 600 W or 600 VA
- 1200 W or 1200 VA
- Nominal Output Voltage
- 220, 230, or 240V (User Selectable)
- Nominal Input Current
- 2.6 A
- 5.2 A
- Acceptable Voltage Range Tolerance
- 160 - 270V (Selector Switch set to 220V)
- 166 - 280V (Selector Switch set to 230V)
- 170 - 290V (Selector Switch set to 240V)
- Rated Input Voltage
- Maximum Acceptable Input Voltage
- Surge Energy
- 300 Joules
- Output Regulation
- Response Time
- < 2 AC Cycles
- Nominal Frequency
- 47 - 63 Hz
- Number of Outlets
- Operating Temperature
- 32 - 104°F (0 - 40°C)
- Relative Humidity
- 0 - 95% Non-condensing
- 4.6 x 8.4 x 5.5 inches (118 x 214 x 141 mm)
- 3.1 kg (6.8 lb)
- 4.2 kg (9.2 lb)
Thank you for purchasing APC by Schneider Electric’s Line-R Automatic Voltage
Regulator! Fill out and mail the product warranty registration form, or fill out an online
form at www.apc.com.
The Line-R automatically corrects brownouts (by boosting low voltage) and overvoltages (by
stepping down high voltage) from the power utility service to levels that are safe for computers,
as well as other sensitive equipment. APC by Schneider Electric’s Line-R provides the highest
degree of protection from line voltage sags and swells, and has been designed for many years of
reliable, maintenance-free service.
The Line-R is designed for use with voltage sensitive equipment such as a: computer, monitor,
inkjet printer, scanner or fax. It is also designed for use with home electronics (TVs, stereos,
CD players, etc.).
Appliances not suitable for use with the Line-R are items such as refrigerators, freezers, power
tools, air conditioners, dehumidifiers, blenders, or any device that employs an AC motor for
operation. Not for use with life sustaining equipment and any device with a power requirement
exceeding the “Maximum Output Power Capacity” rating listed in the Specifications table.
The Line-R provides a front panel power switch (l = on) / (O = off) which functions as the
master power switch for the Line-R and all devices connected to the device.
Push Button Circuit Breaker
The Line-R provides a push button circuit breaker on the rear panel of the unit to protect it from
being overloaded. If the circuit breaker “trips”, unplug the last device connected to the unit and
push the circuit breaker fully inward.
RISK OF EQUIPMENT DAMAGE
The total power consumption of all equipment plugged into the Line-R must not exceed the
ratings listed in the Specifications table below. A total load in excess of the listed ratings will
cause the push button circuit breaker to “trip”.
Failure to follow these instructions can result in equipment damage.
Automatic Voltage Regulator
Models LE600I and LE1200I
Lights when input voltage is high.
Flashes when input voltage is above rated Input
Input voltage is normal.
Lights when input voltage is low.
Flashes when input voltage is below rated Input
The power switch applies and removes power to/
from the Line-R (l = on) / (O = off).
AC Outlets (4)
(connect equipment here)
(see Select Input Voltage)
Power Cord Here and to
an AC Wall Outlet
Connect the Supplied Power
Cord from any Outlet to Your
• Placement - Install the Line-R in a protected environment free of excessive dust,
mechanical vibration, inflammable gases and explosive or corrosive atmospheres.
Do not block the top or side air vents on the unit. Allow 1 inch (2.5 cm) minimum vent
• Select Input Voltage - The Line-R provides a three-position User Selectable Voltage
Switch for adjusting the input voltage for the region where it is being used (example: Russia
- 220V, Denmark - 230V, United Kingdom - 240V). Slide the switch to select the proper
voltage for your location.
• Plug the Line-R into the Wall Outlet - Detach your computer's power cord from the
back of your computer and use it to plug the Line-R into the wall socket. Use one of the two
power cords supplied with the Line-R to reconnect your computer to any of the four outlets
on the back of the Line-R. The Line-R should only be used in buildings having proper
grounding on a branch circuit protected by a fuse or circuit breaker.
• Connect Your Equipment - Plug equipment into the Line-R rear-panel outlets and switch
the equipment ON. The equipment will not be powered until the Line-R is switched ON.
• Switch ON the Line-R - Press the front panel power switch to the on (l) position. This switch
may be used as the master switch for the device and all equipment connected to it.
Characteristics Model LE600I Model LE1200I
Maximum Output Power Capacity 600 W or 600 VA 1200 W or 1200 VA
Nominal Output Voltage 220, 230, or 240V (User Selectable)
Nominal Input Current 2.6 A 5.2 A
Acceptable Voltage Range Tolerance 160 - 270V (Selector Switch set to 220V)
166 - 280V (Selector Switch set to 230V)
170 - 290V (Selector Switch set to 240V)
Rated Input Voltage 250Vac
Maximum Acceptable Input Voltage 300V
Surge Energy 300 Joules
Output Regulation ±10%
Response Time < 2 AC Cycles
Nominal Frequency 47 - 63 Hz
Number of Outlets 4
Operating Temperature 32 - 104°F (0 - 40°C)
Relative Humidity 0 - 95% Non-condensing
Dimensions 4.6 x 8.4 x 5.5 inches (118 x 214 x 141 mm)
Weight 3.1 kg (6.8 lb) 4.2 kg (9.2 lb)
Schneider Electric IT (SEIT) warrants its products to be free from defects in materials and
workmanship for a period of two (2) years from the date of purchase. Its obligation under this
warranty is limited to repairing or replacing, at its sole option, any such defective products. To
obtain service under warranty you must obtain a Return Material Authorization (RMA)
number from SEIT or a SEIT service center. Products must be returned to SEIT or an SEIT
service center with transportation charges prepaid and must be accompanied by a brief
description of the problem encountered and proof of date and place of purchase. This warranty
does not apply to equipment which has been damaged by accident, negligence, or
misapplication or has been altered or modified in any way. This warranty applies to the
original purchaser who must have proper registered the product within 10 days of purchase.
EXCEPT AS PROVIDED HEREIN, SEIT MAKES NO WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A
PARTICULAR PURPOSE. Some countries do not permit limitation or exclusion of implied
warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the
EXCEPT AS PROVIDED ABOVE, IN NO EVENT SHALL SEIT BE LIABLE FOR
DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE. Specifically, SEIT is not liable for any costs, such as
lost profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of
data, costs of substitutes, claims by third parties, or otherwise. This warranty gives you
specific legal rights and you may also have other rights which may vary from location to
APC by Schneider Electric IT Customer Support Worldwide
For country specific customer support, go to the APC by Schneider Electric Web site, www.apc.com.
© 2014 APC by Schneider Electric. APC, the APC logo, SurgeArrest and Line-R are owned by Schneider
Electric Industries S.A.S., or their affiliated companies. All other trademarks are property of their respective