Table of Contents
- Safety and General Information
- Inspect the package contents upon receipt. Notify the carrier and dealer if there is any damage.
- SAVE THESE INSTRUCTIONS - This section contains important instructions that should be followed during installation and maintenance of the UPS and batteries.
- Inventory
- Connect the Battery
- BR650MI /BR900MI
- BR1300MI / BR1600MI
- Install PowerChute™ Personal Edition Software
- Installation
- Connect the Equipment
- BR650MI / BR900MI
- BR1300MI /BR1600MI
- Operation
- Power saving display
- Unit sensitivity
- Front panel buttons and display interface
- Alarms and System Errors
- Audible indicators
- Status icons
- System errors
- Function Button Quick Reference
- Troubleshooting
- Specifications
- Battery Replacement
- Warranty
- APC by Schneider Electric IT Customer Support Worldwide
- User Manual Back-UPS™ Pro BR650/900/1300/1600MI
APC BR1600MI User Manual
Displayed below is the user manual for BR1600MI by APC which is a product in the Uninterruptible Power Supplies (UPSs) category. This manual has pages.
Related Manuals
Safety and General Information
Inspect the package contents upon receipt. Notify the carrier and
dealer if there is any damage.
SAVE THESE INSTRUCTIONS - This section contains important
instructions that should be followed during installation and maintenance
of the UPS and batteries.
Inventory
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
•This UPS is intended for indoor use only.
•Do not operate this UPS in direct sunlight, in contact with fluids, or where there is excessive
dust or humidity.
•Connect the UPS power cable directly to a wall outlet.
•Be sure the air vents on the UPS are not blocked. Allow adequate space for proper ventilation.
•Servicing of batteries should be performed or supervised by personnel knowledgeable about
batteries and required precautions.
•A battery can present a risk of electric shock and burns by high short-circuit current.
•Failed batteries can reach temperatures that exceed the burn thresholds for touchable
surfaces.
Failure to follow these instructions will result in death or serious injury.
bu001b
User Manual Back-UPS™ Pro
BR650/900/1300/1600MI
Back-UPS Pro BR650MI / BR900MI / BR1300MI / BR1600MI2
Connect the Battery
The UPS is shipped with the battery disconnected.
BR650MI /BR900MI
BR1300MI / BR1600MI
Remove the battery door. Remove the battery. Connect the wire.
Push the battery into the unit. Replace the battery door.
Remove the battery door. Remove the battery.
Flip or turn the battery 180 degrees
upward/downward to let green side of the
label face up.
Push the battery into the unit.
Replace the battery door.
b
u
0
2
4
c
bu025c
bu026c
bu055b
bu057b
RED LABEL ON TOP
bu059b
bu058b
GREEN LABEL ON TOP
bu060b
Back-UPS Pro BR650MI / BR900MI / BR1300MI / BR1600MI 3
Install PowerChute™ Personal Edition Software
Use PowerChute Personal Edition software to configure the UPS settings. During a
power outage, PowerChute will save any open files on your computer and shut it down.
When power is restored, it will restart the computer.
Note: PowerChute is only compatible with a Windows operating system. If you are
using Mac OSX, use the native shutdown feature to protect your system. See the
documentation provided with your computer.
Installation
Use the cable supplied with the Back-UPS to connect the data port on the Back-UPS to
the USB port on your computer. On the computer, go to www.apc.com Search for
“PowerChute Personal Edition” then click on “View Details” to download the latest
version of PCPE software. Click the download link and select Software product. Select
the appropriate operating system. Follow directions to download the software.
Connect the Equipment
Battery backup and surge protected outlets
When the Back-UPS is receiving input power, the Battery Backup with Surge Protection
outlets will supply power to connected equipment. During a power outage or other AC
problems, the Battery Backup outlets receive power for a limited time from the Back-
UPS.
Connect equipment such as printers, fax machines, scanners, or other peripherals that do
not need battery backup power to the Surge Protection Only outlets. These outlets
provide full-time protection from surges even if the Back-UPS is switched OFF.
BR650MI / BR900MI BR1300MI /BR1600MI
bu484a
bu485a
Back-UPS Pro BR650MI / BR900MI / BR1300MI / BR1600MI4
Operation
Power saving display
The display interface can be configured to be continuously illuminated, or to save
energy, it can be configured to darken after a period of inactivity.
1. Full Time Mode: Press and hold DISPLAY for two seconds. The display will
illuminate and the Back-UPS will beep to confirm the Full Time mode.
2. Power Saving Mode: Press and hold DISPLAY for two seconds. The display will
darken and the Back-UPS will beep to confirm the Power Saving mode. While in
Power Saving Mode, the display will illuminate if a button is pressed, it then
darkens after 60 seconds of no activity.
Unit sensitivity
Adjust the sensitivity of the Back-UPS to control when it will switch to battery power;
the higher the sensitivity, the more often the Back-UPS will switch to battery power.
1. Ensure the Back-UPS is connected to AC power, but is OFF.
2. Press and hold the POWER button for six seconds. The LOAD CAPACITY bar will
flash on and off, indicating that the Back-UPS is in programming mode.
3. Press POWER again to rotate through the menu options. Stop at selected
sensitivity. The Back-UPS will beep to confirm the selection.
USB and Serial
Data port
To use PowerChute Personal Edition, connect the supplied USB cable or
an optional serial cable (not supplied).
Telephone Cable
Surge Protected
ports
Connect a telephone cable to the IN port, and connect a modem to the
OUT port.
AC Power Input Use a power cable to connect the unit to AC power.
Battery Backup
outlets with Surge
Protection
During a power outage or other AC problems, the Battery Backup outlets
receive power for a limited time from the Back-UPS. Connect critical
equipment such as desktop computer, computer monitor, modem or other
data sensitive devices into these outlets.
Circuit Breaker Use to reset the system after an overload condition has occurred causing
the circuit breaker to trip.
In/Out Ethernet
surge-protected
ports
Use an Ethernet cable to connect a cable modem to the IN port, and
connect a computer to the OUT port.
Surge Protected
outlets
These outlets provide full-time protection from surges, even if the Back-
UPS is off. Connect equipment such as printers and scanners that do not
require battery backup protection.
Generator Sensitivity Default Sensitive Loads
Low sensitivity Medium sensitivity
(Default)
High sensitivity
156-300 Vac 176-294 Vac 176-288 Vac
Input voltage is extremely
low or high. (Not
recommended for
computer loads.)
The Back-UPS frequently
switches to battery power.
The connected equipment
is sensitive to voltage
fluctuations.
Back-UPS Pro BR650MI / BR900MI / BR1300MI / BR1600MI 5
Front panel buttons and display interface
Use the three buttons on the front panel of the Back-UPS and the display interface to
configure the Back-UPS.
Front panel
Mute button
Power On/Off
button
Display button
Display interface
On Line: The Back-UPS is supplying conditioned AC power to connected
equipment
Load Capacity: The load is indicated by the number of sections illuminated,
one to five. Each bar represents 20% of the load.
Battery Charge: The battery charge level is indicated by the number of
sections illuminated. When all five blocks are illuminated, the Back-UPS is at
full charge. When one block is filled, the Back-UPS is near the end of its battery
capacity, the indicator will flash and the Back-UPS will beep continuously.
Overload: The power demand from the load has exceeded the capacity of the
Back-UPS.
Event: The event counter shows the number of events that occurred that caused
the Back-UPS to switch to on-battery operation.
Automatic Voltage Regulation:
When illuminated, the Back-UPS is compensating for low input
voltage
When illuminated, the Back-UPS is compensating for high input
voltage.
In: Input voltage.
Out: Output voltage.
System Error Detected: The system has an error. The error number will
illuminate on the display interface. See “System errors” on page 7.
bu109g
Back-UPS Pro BR650MI / BR900MI / BR1300MI / BR1600MI6
Alarms and System Errors
Audible indicators
Status icons
Mute: If the line through the speaker icon is illuminated, the audible alarm has
been turned off.
Replace Battery: The battery is nearing the end of its useful life. Replace the
battery as early as possible.
On Battery: The Back-UPS is supplying battery backup power to the
connected equipment, it will beep four times every 30 seconds.
Four Beeps Every 30 Seconds Back-UPS is running on battery. You should consider saving
any work in progress.
Continuous Beeping
Low battery condition and battery run-time is very low.
Promptly save any work in progress, exit all open
applications, and shut down the operating system.
Continuous tone Battery Backup outputs are overloaded.
Chirps every 2 Seconds with the Load
Capacity Bar flashing
Battery is disconnected.
Continuous chirping with the Load
Capacity Bar and Replace Battery icon
alternately flashing
Battery did not pass the automatic diagnostic test and should
be replaced as early as possible. Pressing the MUTE button
pauses the chirping.
If these icons are
illuminated... This may be the problem.
The Back-UPS is operating on AC power, but is overloaded. Disconnect one
of the items connected to the Back-UPS. If the Overload icon stops flashing,
the Back-UPS is no longer overloaded and will continue to operate
normally.
The Back-UPS is operating on battery power, but is overloaded. Disconnect
one of the items connected to the Back-UPS. If the Overload icon stops
flashing, the Back-UPS is no longer overloaded and will continue to operate
normally.
The Back-UPS is operating on AC power, but the battery is not functioning
properly. Contact Schneider Electric IT (SEIT) Customer Service to order a
replacement battery. See “Battery Replacement” on page 11.
The Back-UPS is operating on battery power and the battery power is
getting low. Shut down all connected equipment to avoid losing an unsaved
data. When possible, connect the Back-UPS to AC power to recharge the
battery.
Back-UPS Pro BR650MI / BR900MI / BR1300MI / BR1600MI 7
System errors
The Back-UPS will display these error messages. Except for errors F01 and F02, contact
SEIT Technical Support.
F01 On-Battery Overload
Turn the Back-UPS off.
Disconnect non-essential
equipment from the Battery
Backup outlets and the turn
Back-UPS on.
F02 On-Battery Output
Short
Turn the Back-UPS off.
Disconnect all equipment from
the Battery Backup outlets and
the turn Back-UPS on.
Re-connect equipment one item
at a time. If the output is tripped
again, disconnect the device that
caused the error.
F03 On-Battery Xcap
Overload
Errors F03-F09 cannot be
corrected by the user, contact
SEIT Technical Support for
assistance.
F04 Clamp Short
F05 Charge Error
F06 Relay Welding
F07 Temperature
F08 Fan Error (for
BR1600MI only)
F09 Internal Error
bu088a
Back-UPS Pro BR650MI / BR900MI / BR1300MI / BR1600MI8
Function Button Quick Reference
Function Button
Timing
(seconds)
UPS
Status Description
Power
Power On 0.2 Off
Press POWER to start receiving input AC power. If AC
input power is not available, the Back-UPS will run on
battery power.
Power Off 2On
The Back-UPS is not receiving input AC power, but is
providing surge protection.
Display
Status
Inquiry 0.2 On
Verify the status or condition of the Back-UPS. The
LCD will illuminate for 60 seconds. Press the button
the toggle into various information.
Full-Time/
Power-
Saving
mode
2On
The LCD will illuminate and the Back-UPS will beep
to confirm the Full-Time mode. The LCD will darken
and the Back-UPS will beep to confirm the Power-
Saving mode. While in Power-Saving Mode, the LCD
will illuminate if a button is pressed, then darkens after
60 seconds of no activity.
Mute
General
Status
Enable/
Disable
2On
Enable or disable the audible alarms. The Mute icon
will illuminate and the Back-UPS will beep one time.
The Mute function will not activate unless the Back-
UPS is operating on battery power.
Sensitivity 6Off
The Load Capacity icon will blink, indicating that the
Back-UPS is in programming mode. Use the POWER
button to scroll through Low, Medium, and High, stop
at selected sensitivity. The Back-UPS will beep to
confirm selection. See "Unit sensitivity" for details.
Self-Test
(manual) 6On
The Back-UPS will perform a test of the internal
battery. Note: This will happen automatically when the
Back-UPS is turned ON or when the Back-UPS
previously detected a bad battery.
Event
Reset 0.2 On
When the Event screen is visible, press and hold
DISPLAY, then press POWER, to clear the detected error
event counter.
Error
Reset 2Error
After an error has been identified, press POWER to
remove the visual indication and return to standby
status.
Back-UPS Pro BR650MI / BR900MI / BR1300MI / BR1600MI 9
Troubleshooting
Problem Possible Cause Corrective Action
Back-UPS will not
switch on.
The Back-UPS is not connected to
AC power.
Ensure that the Back-UPS is securely
connected to an AC outlet.
The circuit breaker has been
tripped.
Disconnect non-essential equipment
from the Back-UPS. Reset the circuit
breaker. Re-connect equipment one
item at a time. If the circuit breaker is
tripped again, disconnect the device
that caused the trip.
The internal battery is not
connected.
Connect the battery.
The AC input voltage is out of
range.
Adjust the transfer voltage and
sensitivity range.
The Back-UPS
does not provide
power during a AC
power outage.
Ensure that essential equipment is
not plugged into a SURGE ONLY
outlet.
Disconnect equipment from the
SURGE ONLY outlet and re-connect to
a Battery Backup outlet.
The Back-UPS is
operating on
battery power,
while connected to
AC power.
The plug has partially pulled out of
the wall outlet, the wall outlet is no
longer receiving AC power, or the
circuit breaker has been tripped.
Ensure that the plug is fully inserted
into the wall outlet. Ensure that the
wall outlet is receiving AC power by
checking it with another device.
The Back-UPS is performing an
automatic self test.
No action is necessary.
The AC input voltage is out of
range, the frequency is out of
range, or the waveform is distorted.
Adjust the transfer voltage and
sensitivity range.
The Back-UPS
does not provide
the expected
amount of backup
time.
Battery Backup outlets may be
fully or improperly loaded.
Disconnect non-essential equipment
from the Battery Backup outlets and
connect the equipment to SURGE
outlets.
The battery was recently
discharged due to a power outage
and has not fully recharged.
Charge the battery cartridge for 16
hours.
The battery has reached the end of
its useful life.
Replace the battery.
The REPLACE
BATTERY indicator
is illuminated.
The battery has reached the end of
its useful life.
Replace the battery as early as
possible.
The OVERLOAD
indicator is
illuminated.
The equipment connected to the
Back-UPS is drawing more power
than the Back-UPS can provide.
Disconnect non-essential equipment
from the Battery Backup outlets and
connect the equipment to SURGE
outlets.
The SYSTEM ERROR
indicator is
illuminated, all the
front panel
indicators are
flashing.
There is an internal error. Determine which internal error
message is displayed by matching
the number displayed on the LCD
with the corresponding Error
Message (see "System errors") and
contact SEIT Technical Support.
Back-UPS Pro BR650MI / BR900MI / BR1300MI / BR1600MI10
Specifications
Model BR650MI BR900MI BR1300MI BR1600MI
VA 650 VA 900 VA 1300 VA 1600 VA
Maximum Load 390 W 540 W 780 W 960 W
Nominal Input Voltage 220 - 240 Vac
Online Input Voltage
Range
176 - 294 Vac
Automatic Voltage
Regulation
Boost by +11.5% when input voltage drops below limit
Trim by -11.5% when input voltage exceeds limit
Frequency Range 50/60 Hz ± 3 Hz
Battery Type Lead acid, 12V with 1 battery Lead acid, 12V with 2 batteries
On-battery Waveshape Step-approximated sine-wave
Typical Recharge Time 12 hours 16 hours
Transfer Time 8 ms (typical), 10 ms (maximum)
On Battery Runtime Go to: www.apc.com
Interface USB
Operating Temperature 08 to 408 C (328 to 1048 F)
Storage Temperature -58 to 458 C (238 to 1138 F)
IP Rating IP20
Unit Dimensions 19 x 9.1 x 31 cm
(7.5 x 3.6 x 12.2 in)
25 x 10 x 38.2 cm
(9.8 x 3.9 x 15 in)
Unit Weight 6.8 kg
(15 lbs)
7.2 kg
(15.9 lbs)
10.2 kg
(22.5 lbs)
11.0 kg
(24.3 lbs)
Back-UPS Pro BR650MI / BR900MI / BR1300MI / BR1600MI 11
Battery Replacement
The battery typically lasts for 3 to 5 years, a shorter period if subjected to frequent
outages or elevated temperatures. Battery replacement parts for Back-UPS BR650MI is
APCRBC110, for BR900MI is APCRBC164, for BR1300MI is APCRBC165, and for
BR1600MI is APCRBC166. Delaying the replacement of parts may corrode the
batteries in the cartridge. Recycle spent battery cartridges.
Warranty
The standard warranty is three (3) years from the date of purchase, valid in European
Community. For all other regions, the standard warranty is two (2) years from the date of
purchase. Schneider Electric IT (SEIT) standard procedure is to replace the original unit
with a factory reconditioned unit. Customers who must have the original unit back due to
the assignment of asset tags and set depreciation schedules must declare such a need at
first contact with an SEIT Technical Support representative. SEIT will ship the
replacement unit once the defective unit has been received by the repair department, or
cross-ship upon the receipt of a valid credit card number. The customer pays for shipping
the unit to SEIT. SEIT pays ground freight transportation costs to ship the replacement
unit to the customer.
CAUTION
RISK OF HYDROGEN SULPHIDE GAS AND EXCESSIVE SMOKE
•Replace the battery at least every 5 years.
•Replace the battery immediately when the UPS indicates battery replacement is necessary.
•Replace battery at the end of its service life.
•Replace batteries with the same number and type of batteries as originally installed in the
equipment.
•Replace the battery immediately when the UPS indicates a battery over-temperature
condition, or UPS internal over-temperature, or when there is evidence of electrolyte leakage.
Power off the UPS, unplug it from the AC input, and disconnect the batteries. Do not operate
the UPS until the batteries have been replaced.
Failure to follow these instructions can result in minor or moderate injury and
equipment damage.
APC by Schneider Electric IT Customer Support
Worldwide
For country specific customer support, go to the APC by Schneider Electric Web site,
www.apc.com.
© 2019 APC by Schneider Electric. APC, the APC logo, Back-UPS, and
PowerChute are owned by Schneider Electric Industries S.A.S. or their affiliated
companies. All other trademarks are property of their respective owners.
EN 990-91253A
05/2019