Table of Contents
APC ER7SIDE4210 User Manual
Displayed below is the user manual for ER7SIDE4210 by APC which is a product in the Rack Accessories category. This manual has pages.
Related Manuals
Easy Rack
Open-Side Racks and Accessories
Installation
May 2021
www.apc.com
Legal Information
The Schneider Electric brand and any trademarks of Schneider Electric SE and its
subsidiaries referred to in this guide are the property of Schneider Electric SE or its
subsidiaries. All other brands may be trademarks of their respective owners.
This guide and its content are protected under applicable copyright laws and
furnished for informational use only. No part of this guide may be reproduced or
transmitted in any form or by any means (electronic, mechanical, photocopying,
recording, or otherwise), for any purpose, without the prior written permission of
Schneider Electric.
Schneider Electric does not grant any right or license for commercial use of the
guide or its content, except for a non-exclusive and personal license to consult it on
an "as is" basis. Schneider Electric products and equipment should be installed,
operated, serviced, and maintained only by qualified personnel.
As standards, specifications, and designs change from time to time, information
contained in this guide may be subject to change without notice.
To the extent permitted by applicable law, no responsibility or liability is assumed
by Schneider Electric and its subsidiaries for any errors or omissions in the
informational content of this material or consequences arising out of or resulting
from the use of the information contained herein.
Open-Side Racks and Accessories
Table of Contents
Introduction ..................................................................................................5
Safety............................................................................................................6
Safety Instructions ......................................................................................7
Component Identification...........................................................................8
Hardware...................................................................................................8
Tools Provided ...........................................................................................9
Rack Installation........................................................................................10
Move the Rack .........................................................................................10
Level the Rack .........................................................................................12
Join the Racks..........................................................................................12
Ground the Rack ......................................................................................13
Secure the Rack.......................................................................................14
Roof, and Doors .......................................................................................14
Roof Removal.....................................................................................14
Door Removal ....................................................................................15
Door Installation..................................................................................15
Reverse the Front Door .......................................................................16
Equipment Installation..............................................................................18
Adjust the Vertical Mounting Flanges..........................................................18
Zero U Accessory Mounting Brackets.........................................................21
Install the Equipment ................................................................................22
Accessories ...............................................................................................24
Specifications ............................................................................................27
Five-Year Factory Warranty.....................................................................28
990–6497–001 3
Introduction Open-Side Racks and Accessories
Introduction
The APC by Schneider Electric Open-Side Easy Racks are quality racks for
storage of industry-standard (EIC/ECA-310), 19 in. (483 mm) rack-mounted
hardware, which includes servers and voice, data, networking, internetworking,
and power protection equipment.
This manual covers the general installation and customization of the open-sided
racks in the Easy Rack family and their accessories.
SKU Rack Description
(W = Width, D = Depth)
SKU Accessory Description
ER6200 42U, 600W x 1000D ER7BP1U Blanking Panel
ER6220 42U, 600W x 1200D ER7BP2U Blanking Panel
ER6800 48U, 600W x 1000D ER7RCC42 Rear Cable Channel
ER6820 48U, 600W x 1200D ER7RCC48 Rear Cable Channel
ER8200 42U, 800W x 1000D ER7DCM Cable Manager 1U depth
ER8220 42U, 800W x 1200D ER7HCM Horizontal Cable Manager
ER8800 48U, 800W x 1000D ER7VCM42 Vertical Cable Manager 42U
ER8820 48U, 800W x 1200D ER7VCM48 Vertical Cable Manager 48U
ER7PDUBRKT PDU Mounting Bracket for
1100 mm and 1200 mm depth
Easy Racks
ER7PDUBRKTS PDU Mounting Bracket for 800
mm and 1000 mm depth Easy
Racks
ER7SHELF Adjustable Shelf, 50kg, for use
in 800mm depth rack
ER7SHELFS Accessory Shelf
ER7SIDE4210 Side Panel for 42U/1000mm
Easy Racks
ER7SIDE4212 Side Panel for 42U/1200mm
Easy Racks
ER7SIDE4810 Side Panel for 48U/1000mm
Easy Racks
ER7SIDE4812 Side Panel for 48U/1200mm
Easy Racks
990–6497–001 5
Open-Side Racks and Accessories Safety
Safety
Read the instructions carefully to become familiar with the equipment before trying
to install, operate, service or maintain it.
The addition of this symbol to a Danger or Warning safety label indicates that an
electrical hazard exists which will result in personal injury if the instructions are not
followed.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety message that follow this symbol to avoid possible injury
or death.
DANGER
DANGER indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Failure to follow these instructions will result in death or serious injury.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided, can
result in death or serious injury.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, can
result in minor or moderate injury.
Failure to follow these instructions can result in injury or equipment
damage.
NOTICE
NOTICE addresses practices not related to physical injury including certain
environmental hazards, potential damage or loss of data.
Failure to follow these instructions can result in equipment damage.
6 990–6497–001
Safety Open-Side Racks and Accessories
Safety Instructions
This manual contains important instructions that must be followed during the
installation and customization of the rack.
DANGER
ELECTRIC SHOCK HAZARD
Connection of the rack to the Common Bonding Network (CBN) of the building
is required.
Failure to follow these instructions will result in death or serious injury.
WARNING
TIP/HEAVY EQUIPMENT HAZARD
• This rack may be easily tipped. Use extreme caution when unpacking or
moving.
• At least two people are required to unpack and move the rack.
• Before moving the rack on its casters, load 158 kg (350 lb) of equipment into
the bottom of the rack for extra stability.
• Make sure the leveling feet are up and push the rack only from the front or
rear when moving the rack on its casters. Never push the rack from the
sides.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
CAUTION
LIFTING HAZARD
• Use M10 eye bolts with a shoulder rated for 181 kg (400 lb).
• Use appropriate lifting hardware to assure straight-line pull on lifting eye
bolts.
Failure to follow these instructions can result in injury or equipment
damage.
CAUTION
FALLING EQUIPMENT HAZARD
Do NOT install cage nuts vertically with the tabs engaging the top and bottom of
the square hole.
Failure to follow these instructions can result in injury or equipment
damage.
990–6497–001 7
Open-Side Racks and Accessories Component Identification
Component Identification
ER6820 shown (48U, 600W x 1200D)
ns3243a
Item Description Item Description
1 Roof 6 Leveling Feet (4)
2 Rear Doors (2) 7 Hardware bag
3 Zero U Accessory Mounting Bracket
(4)
Can be mounted in various locations
throughout the rack to support small
accessories and equipment.
8 Removable and reversible front door
4 Cabinet Frame 9 Key (2)
5Caster (4) 10 Vertical Mounting Flange (4)
Hardware
Plastic Cup Washer M6
(50)
Cage Nut (50)
M5 x 12 Phillips screw (4) M6 x 16 Phillips
screw (50)
8 990–6497–001
Open-Side Racks and Accessories Rack Installation
Rack Installation
Move the Rack
WARNING
TIP HAZARD
• This rack is easily tipped. Use extreme caution when unpacking or moving.
• At least two people are required to unpack and move the rack.
• Make sure the leveling feet are up and push the rack only from the front or
rear when moving the rack on its casters. Never push the rack from the
sides.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
Labels
Labels can be found on the rack that serve to communicate:
Tip Hazard
Extend Slide-Mounted Hardware One Piece at a time
Casters: The rack can be moved (Dynamic Load) on its casters with up to 600 kg
(1320 lb) of equipment installed. With the leveling feet lowered, the static rack
can be loaded with up to 1200 kg (2640 lb) of equipment (Static Load).
Dynamic load:
1322 lbs Max
(600 kg)
Static load:
2645 lbs Max
(1200 kg)
ns3126a
10 990–6497–001
Rack Installation Open-Side Racks and Accessories
Eye Bolts
CAUTION
LIFTING HAZARD
• Use M10 eye bolts with a shoulder rated for 181 kg (400 lb).
• Use appropriate lifting hardware to assure straight-line pull on lifting eye
bolts.
Failure to follow these instructions can result in injury or equipment
damage.
Use M10 eye bolts with a shoulder rated for
181 kg (400 lb) when lifting the Easy Rack.
ns3262a
Assure a straight-line pull on the lifting eye bolts
when lifting the Easy Rack.
ns3261a
990–6497–001 11
Open-Side Racks and Accessories Rack Installation
Level the Rack
The leveling feet at the corners of the Easy Rack
provide a stable base if the floor is uneven, but
they cannot compensate for a badly sloped
surface.
Ensure the rack is in its intended location.
Use a 13mm open-ended wrench to lower the
leveling feet if the rack is loaded with equipment.
Adjust each foot and, using a level, adjust the
feet until the rack is level and plumb.
ns3245a
Join the Racks
Join racks with the provided brackets to provide alignment and added stability.
Racks may be joined with or without the side panels installed.
WARNING
TIP HAZARD
Joining racks provides limited stability to the racks. Secure the rack to the floor
before installing equipment.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
If installed, remove the front and rear doors. See the “Door Removal” section for
instructions.
Choose between 24 in. or 600 mm centers.
Align the racks and locate the joining brackets.
There are two brackets on the front and two
brackets on the back of each rack.
Racks are joined using a M5 x 12 countersunk
screw, provided in the hardware bag. Using the
Phillips head end of the provided tool or a
Phillips head screwdriver, insert the screw into
the designated hole and tighten.
ns3251a
X4
24 in.
600 mm
Install the doors. See the “Door Installation” section for instructions.
12 990–6497–001
Rack Installation Open-Side Racks and Accessories
Ground the Rack
DANGER
ELECTRIC SHOCK HAZARD
Connection of the rack to the Common Bonding Network (CBN) of the building
is required.
Failure to follow these instructions will result in death or serious injury.
Each rack should be bonded directly to a common ground using one of the
designated grounding locations (two M6 threaded inserts) at the top or bottom of
the cabinet.
• Use a Common Bonding Network Kit (for example: Listed [KDER] Panduit®
RGCBNJ660PY or equivalent).
• Use paint-piercing washers between the ground terminal and the rack frame,
or remove the paint on the frame under the ground terminals, per NEC NFPA
70 Article 250.12.
• Torque the screws to 6.9 N•m (60 lb-in.).
NOTE: Additional functional grounding points are available at the top of the
rack. Do not connect the building CBN to these functional grounding points.
ns3252a
990–6497–001 13
Open-Side Racks and Accessories Rack Installation
Secure the Rack
WARNING
TIP HAZARD
Secure the rack to the floor before installing equipment.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
NOTE: Secure the rack to the floor only with the casters and leveling feet
installed and the leveling feet in position to firmly and levelly support the rack.
The rack can be bolted to the floor as shown
below. Open or remove the doors to access the
mounting points on the rack’s frame. Use the
brackets that secured the rack to the pallet for
shipping.
The illustration shows the brackets at the front
and rear of the rack. Doors removed for clarity.
ns3253a
Roof, and Doors
Roof Removal
From the inside of the rack, remove the two
screws at the back of the roof then push up. The
roof can then be removed from the outside.
ns3254a
14 990–6497–001
Rack Installation Open-Side Racks and Accessories
Door Removal
Unlock and open the front door.
Disconnect the ground wire and any other wire
connections that may interfere with the removal
of the doors.
ns3246a
The hinges come apart by lifting the door up and
away from the rack.
ns3255a
Door Installation
The doors self-align on hinge pins when
properly installed. With the door at a 90 degree
angle to the front of the rack, position the door
over the hinge pins.
Slowly lower the door into the rack frame
ensuring that the door hinges correctly align to
the rack frame hinges.
ns3097a
Connect the ground wire and any other wire
connections.
ns3246a
990–6497–001 15
Open-Side Racks and Accessories Rack Installation
Reverse the Front Door
NOTE: The front door can be reversed so that the door opens in the other
direction. This procedure assumes that initially, when facing the cabinet, the
hinges are on the left and the door is opening from the right.
Remove the handle by removing the screw-
plate. Pull the handle from the door.
ns3249a
Disconnect the ground wire, and any other
connections. Remove the door from the frame.
ns3246a
Locate the upper hinge on the rack frame.
Remove the two screws holding the hinge in
place. Install the hinge onto the other side of the
rack frame. Repeat this step for the lower hinge.
ns3104a
Rotate the door. Remove the hinges from the
door, and install them to the alternate hole
location. The hinges on the door should now
align with the hinges on the rack.
ns3105a
2
3
1
16 990–6497–001
Rack Installation Open-Side Racks and Accessories
Install the door to the hinges now on the reverse
side of the rack. Connect the ground wire and
any other wire connections previously
disconnected.
Locate the lock handle. Remove the cam screw,
cam washer, and cam.
ns1766a
Rotate the cam washer 90 degrees, and the
latch 180 degrees. Install the handle on the
door.
ns3106a
Rotate the door logo
When the door has been reversed, the logo will
now be located on the bottom of the door. The
logo is attached to the perforated holes in the
door with three (3) clips. Remove the logo by
carefully pulling each clip from its perforated
hole, rotate it, and install it at the top of the door.
ns3259a
990–6497–001 17
Open-Side Racks and Accessories Equipment Installation
Equipment Installation
NOTE: Easy Racks are intended for use with Listed equipment. If un-Listed
equipment is installed, you should evaluate the safety of your configuration.
Adjust the Vertical Mounting Flanges
Vertical mounting flanges come factory-installed
at 737 mm (29 in.), the proper location for use
with rack-mountable equipment.
The mounting flanges are adjustable towards
the front or the rear of the cabinet to
accommodate different rails or equipment with
other depths.
A common application for the 800 mm (31.5 in.)
racks is to move the flanges to a depth of
476 mm (18.75.) to accommodate networking
and telecommunications equipment.
ns1621b
18 990–6497–001
Equipment Installation Open-Side Racks and Accessories
Position the Vertical Mounting Flanges
Configuration 1: The Accessory Channel is
installed. The Vertical Mounting Flanges can be
installed a minimum distance of (a) and can
extend as far as (b).
Configuration 2: The Accessory Channel is
removed. The Vertical Mounting Flanges can
extend as far as (c).
12
W W
D D
a
b
c
ns3109a
SKU Cabinet
Width
(W)
Cabinet
Depth
(D)
abc
ER6200 600 mm 1000 mm 190.5 mm
(7.5 in.)
749.3 mm
(29.5 in.)
838.2 mm
(33 in.)
ER6220 600 mm 1200 mm 190.5 mm
(7.5 in.)
876.3 mm
(34.5 in.)
1041.4 mm
(41 in.)
ER8200 800 mm 1000 mm 241.64 mm
(9.51 in.)
749.3 mm
(29.5 in.)
838.2 mm
(33 in.)
ER8220 800 mm 1200 mm 241.64 mm
(9.51 in.)
876.3 mm
(34.5 in.)
1041.4 mm
(41 in.)
ER6820 600 mm 1200 mm 190.5 mm
(7.5 in.)
876.3 mm
(34.5 in.)
1041.4 mm
(41 in.)
ER6800 600 mm 1000 mm 190.5 mm
(7.5 in.)
749.3 mm
(29.5 in.)
838.2 mm
(33 in.)
ER8820 800 mm 1200 mm 241.64 mm
(9.51 in.)
876.3 mm
(34.5 in.)
1041.4 mm
(41 in.)
ER8800 800 mm 1000 mm 241.64 mm
(9.51 in.)
749.3 mm
(34.5 in.)
838.2 mm
(33 in.)
Vertical Mounting Flange Adjustment
WARNING
FALLING EQUIPMENT
Remove all equipment installed on the vertical mounting flanges before
performing any adjustments.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
Loosen the top and bottom screws holding the vertical mounting flange in place.
The brackets, all held in place by the screws, will now be loose. Move all three
brackets to the desired position.
990–6497–001 19
Equipment Installation Open-Side Racks and Accessories
Zero U Accessory Mounting Brackets
The Zero U Accessory Mounting Brackets may be moved to different locations
within the rack in order to mount your equipment. There are two different Mounting
Brackets in the rack. One for the left side and one for the right side. The smallest
part of the mounting holes in the bracket should be at the bottom when it is in the
proper position.
To reposition the Zero U Mounting Bracket
The Mounting Bracket is attached to the rack with two (2) M6 x 12 pan head T30
screws and two (2) cage nuts.
1. Remove the two (2) M6 x 12 pan head T30 screws with the Torx tool
(provided).
2. Remove the Mounting Bracket and then, remove the cage nuts from their
current location.
3. Install the cage nuts in the location you have chosen to mount your
equipment.
4. Install the Mounting Bracket with the two (2) M6 x 12 pan head T30 screws.
5. Mount your equipment. Mounting a Rack PDU with a toolless mounting
bracket is shown in the illustration below.
Left
Right
The Easy Rack is shown with doors removed for clarity.
990–6497–001 21
Open-Side Racks and Accessories Equipment Installation
Install the Equipment
WARNING
TIP HAZARD
• This rack is easily tipped. Make sure you have secured the rack to the floor
before installing equipment.
• Install the heaviest equipment first and toward the bottom of the rack to
prevent the rack from becoming top-heavy.
• Do not extend equipment on sliding rails until you have 150 kg (350 lb) of
equipment installed in the bottom of the rack for stability or until the rack is
bolted to the floor and secured to neighboring racks in the row. Never extend
more than one piece of equipment on sliding rails at a time.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
To install rack-mount equipment in the cabinet:
1. Review the equipment manufacturer’s installation instructions.
2. Locate the top and bottom U space on the vertical mounting rails. Every third
hole on the mounting rails is numbered to indicate the middle of a U space.
3. Install the cage nuts on the interior of the vertical mounting rail; then install the
equipment.
1U
7
6
5
ns0014a
22 990–6497–001
Equipment Installation Open-Side Racks and Accessories
Cage Nuts
Cage nuts are provided in the hardware bag inside the rack.
CAUTION
FALLING EQUIPMENT HAZARD
Do NOT install cage nuts vertically with the tabs engaging the top and bottom of
the square hole.
Failure to follow these instructions can result in injury or equipment
damage.
• Install cage nuts horizontally, with the tabs engaging the sides of the square
hole.
• Install the cage nuts on the interior of the vertical mounting rail.
ns1768a
Installation:
1. From the inside of the rack, insert the cage nut into the square hole.
2. Hook one tab of the cage nut assembly through the far side of the hole.
3. Place the cage nut tool on the other side of the cage nut and pull to snap it
into position.
gen0188a
Removal:
1. Remove any attached screw.
2. Grasp the cage nut and squeeze the sides to release it from the square hole.
990–6497–001 23
Open-Side Racks and Accessories Accessories
Accessories
Optional accessories can be ordered separately. Installation hardware is included
with the accessory. See accessory list below.
SKU Description
ER7BP1U 1U Blanking panel,
Qty 10
ER7BP2U 2U Blanking panel,
Qty 10
ER7DCM 1U Cable manager, for
use along the depth of
the Easy Rack, Qty 1
ER7RCC42 0U Rear Cable
Channel, for use in
42U Easy Rack, Qty 2
24 990–6497–001
Open-Side Racks and Accessories Accessories
ER7HCM 1U Horizontal cable
management for
installation in front of
Easy Rack, Qty 1
ER7SHELF Shelf, 50kg, for use in
800mm depth rack,
Qty 1
ER7SHELFS Accessory Shelf, Qty 1
ER7PDUBRKT Mounting bracket (left
and right), for
installation on rear of
1100 and 1200 depth
Easy Racks to install
PDU or cable
manager, 2 pair
ER7PDUBRKTS Mounting bracket (left
and right), for
installation on rear of
800 and 1000 depth
Easy Racks to install a
Rack PDU or cable
manager, 2 pair
ER7SIDE4210
ER7SIDE4212
ER7SIDE4810
ER7SIDE4812
Side Panels, black, top
with lock and bottom,
for use with 42U/
1000mm deep Easy
Racks
Side Panels, black, top
with lock and bottom,
for use with 42U/
1200mm deep Easy
Racks
Side Panels, black, top
with lock and bottom,
for use with 48U/
1000mm deep Easy
Racks
Side Panels, black, top
with lock and bottom,
for use with 48U/
1200mm deep Easy
Racks
26 990–6497–001
Specifications Open-Side Racks and Accessories
Specifications
General specifications for Open-Side Easy Racks:
SKU Height with
Castor
Height
without
Castor
Width Depth U Space
ER6200 1991 mm
(78.38 in.)
1955 mm
(76.96 in.)
600 mm (23.6 in.) 1000 mm (39.37 in.) 42 U
ER6220 1991 mm
(78.38 in.)
1955 mm
(76.96 in.)
600 mm (23.6 in.) 1200 mm (47.24 in.) 42 U
ER8200 1991 mm
(78.38 in.)
1955 mm
(76.96 in.)
800 mm (31.49 in.) 1000 mm (39.37 in.) 42 U
ER8220 1991 mm
(78.38 in.)
1955 mm
(76.96 in.)
800 mm (31.49 in.) 1200 mm (47.24 in.) 42 U
ER6820 2258 mm
(88.89 in.)
2222 mm
(87.48 in.)
600 mm (23.6 in.) 1200 mm (47.24 in.) 48 U
ER6800 2258 mm
(88.89 in.)
2222 mm
(87.48 in.)
600 mm (23.6 in.) 1000 mm (39.37 in.) 48 U
ER8820 2258 mm
(88.89 in.)
2222 mm
(87.48 in.)
800 mm (31.49 in.) 1200 mm (47.24 in.) 48 U
ER8800 2258 mm
(88.89 in.)
2222 mm
(87.48 in.)
800 mm (31.49 in.) 1000 mm (39.37 in.) 48 U
SKU Front and Rear Door
Perforation Pattern
Weight Rating: Static
Load ¹
Weight Rating: Dynamic
(Rolling) Load ²
All 80.8% open area 1200 kg (2640 lb.) 600 kg (1320 lb.)
¹ Lower the leveling feet if the static weight is over 1200 kg (2640 lb).
² Dynamic (Rolling) rating valid only for rolling the rack into position.
990–6497–001 27
Open-Side Racks and Accessories Five-Year Factory Warranty
Five-Year Factory Warranty
The limited warranty provided by APC by Schneider Electric in this Statement of
Limited Factory Warranty applies only to products you purchase for your
commercial or industrial use in the ordinary course of your business.
Terms of Warranty
APC by Schneider Electric warrants its products to be free from defects in
materials and workmanship for a period of five years from the date of purchase.
The obligation of APC by Schneider Electric under this warranty is limited to
repairing or replacing, at its sole discretion, any such defective products. This
warranty does not apply to equipment that has been damaged by accident,
negligence, or misapplication or has been altered or modified in any way. Repair
or replacement of a defective product or part thereof does not extend the original
warranty period. Any parts furnished under this warranty may be new or factory-
remanufactured.
Non-transferable warranty
This warranty extends only to the original purchaser who must have properly
registered the product. The product may be registered at the APC by Schneider
Electric website, www.apc.com.
Exclusions
APC by Schneider Electric shall not be liable under the warranty if its testing and
examination disclose that the alleged defect in the product does not exist or was
caused by end user’s or any third person’s misuse, negligence, improper
installation or testing. Further, APC by Schneider Electric shall not be liable under
the warranty for unauthorized attempts to repair or modify wrong or inadequate
electrical voltage or connection, inappropriate on-site operation conditions,
corrosive atmosphere, repair, installation, start-up by non-APC by Schneider
Electric designated personnel, a change in location or operating use, exposure to
the elements Acts of God, fire, theft, or installation contrary to APC by Schneider
Electric serial number has been altered, defaced, or removed, or any other cause
beyond the range of the intended use.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, BY OPERATION OF
LAW OR OTHERWISE, OF PRODUCTS SOLD, SERVICED OR FURNISHED
UNDER THIS AGREEMENT OR IN CONNECTION HEREWITH. APC BY
SCHNEIDER ELECTRIC DISCLAIMS ALL IMPLIED WARRANTIES OF
MERCHANTABILITY, SATISFACTION AND FITNESS FOR A PARTICULAR
PURPOSE. APC BY SCHNEIDER ELECTRIC EXPRESS WARRANTIES WILL
NOT BE ENLARGED, DIMINISHED, OR AFFECTED BY AND NO OBLIGATION
OR LIABILITY WILL ARISE OUT OF, APC BY SCHNEIDER ELECTRIC
RENDERING OF TECHNICAL OR OTHER ADVICE OR SERVICE IN
CONNECTION WITH THE PRODUCTS. THE FOREGOING WARRANTIES AND
REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES
AND REMEDIES. THE WARRANTIES SET FORTH ABOVE CONSTITUTE APC
BY SCHNEIDER ELECTRIC’S SOLE LIABILITY AND PURCHASER’S
EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH WARRANTIES. APC BY
SCHNEIDER ELECTRIC WARRANTIES EXTEND ONLY TO PURCHASER AND
ARE NOT EXTENDED TO ANY THIRD PARTIES.
IN NO EVENT SHALL APC BY SCHNEIDER ELECTRIC, ITS OFFICERS,
DIRECTORS, AFFILIATES OR EMPLOYEES BE LIABLE FOR ANY FORM OF
INDIRECT, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, ARISING
OUT OF THE USE, SERVICE OR INSTALLATION, OF THE PRODUCTS,
WHETHER SUCH DAMAGES ARISE IN CONTRACT OR TORT,
28 990–6497–001
Five-Year Factory Warranty Open-Side Racks and Accessories
IRRESPECTIVE OF FAULT, NEGLIGENCE OR STRICT LIABILITY OR
WHETHER APC BY SCHNEIDER ELECTRIC HAS BEEN ADVISED IN
ADVANCE OF THE POSSIBILITY OF SUCH DAMAGES. SPECIFICALLY, APC
BY SCHNEIDER ELECTRIC IS NOT LIABLE FOR ANY COSTS, SUCH AS
LOST PROFITS OR REVENUE, LOSS OF EQUIPMENT, LOSS OF USE OF
EQUIPMENT, LOSS OF SOFTWARE, LOSS OF DATA, COSTS OF
SUBSTITUTES, CLAIMS BY THIRD PARTIES, OR OTHERWISE.
NO SALESMAN, EMPLOYEE OR AGENT OF APC BY SCHNEIDER ELECTRIC
IS AUTHORIZED TO ADD TO OR VARY THE TERMS OF THIS WARRANTY.
WARRANTY TERMS MAY BE MODIFIED, IF AT ALL, ONLY IN WRITING
SIGNED BY AN APC BY SCHNEIDER ELECTRIC OFFICER AND LEGAL
DEPARTMENT.
Warranty Claims
Customers with warranty claims issues may access the APC by Schneider
Electric customer support network through the Support page of the APC by
Schneider Electric website, www.apc.com/support. Select your country from the
country selection pull-down menu at the top of the Web page. Select the Support
tab to obtain contact information for customer support in your region.
990–6497–001 29
APC by Schneider Electric
70 Mechanic Street
02035 Foxboro, MA
USA
www.apc.com
As standards, specifications, and design change from time to time,
please ask for confirmation of the information given in this publication.
© 2021 – Schneider Electric. All rights reserved.
990–6497–001