Table of Contents
- Important Safety Instructions — SAVE THESE INSTRUCTIONS
- User Interface
- UPS Configuration
- Operation
- Operating Modes
- Operation Procedures
- UPS Breakers and Switches
- Start Up a Single UPS on Input Source
- Start Up a Single UPS on Bypass Source
- Shut Down a Single UPS
- Restart a Single UPS
- Shut Down a Parallel Configuration
- Restart a Galaxy 5000 480 V Parallel Configuration
- Restart a Galaxy 5500 400 V Parallel Configuration
- Isolate the UPS
- Return the UPS to Normal Operation
- Operation of the Dry Contact Communication Card
- Maintenance
- Troubleshooting
APC G55TBATL7L10E User Manual
Displayed below is the user manual for G55TBATL7L10E by APC which is a product in the UPS Battery Cabinets category. This manual has pages.
Related Manuals
Galaxy 5000/Galaxy 5500
40–130 kVA 480 V,
20–120 kVA 400 V
Operation
04/2016
www.schneider-electric.com
Legal Information
The Schneider Electric brand and any registered trademarks of Schneider Electric
Industries SAS referred to in this guide are the sole property of Schneider Electric
SA and its subsidiaries. They may not be used for any purpose without the owner's
permission, given in writing. This guide and its content are protected, within the
meaning of the French intellectual property code (Code de la propriété
intellectuelle français, referred to hereafter as "the Code"), under the laws of
copyright covering texts, drawings and models, as well as by trademark law. You
agree not to reproduce, other than for your own personal, noncommercial use as
defined in the Code, all or part of this guide on any medium whatsoever without
Schneider Electric's permission, given in writing. You also agree not to establish
any hypertext links to this guide or its content. Schneider Electric does not grant
any right or license for the personal and noncommercial use of the guide or its
content, except for a non-exclusive license to consult it on an "as is" basis, at your
own risk. All other rights are reserved.
Electrical equipment should be installed, operated, serviced, and maintained only
by qualified personnel. No responsibility is assumed by Schneider Electric for any
consequences arising out of the use of this material.
As standards, specifications, and designs change from time to time, please ask for
confirmation of the information given in this publication.
40–130 kVA 480 V,20–120 kVA 400 V
Table of Contents
Important Safety Instructions — SAVE THESE
INSTRUCTIONS.........................................................................................5
FCC Statement ..........................................................................................6
Safety Precautions .....................................................................................6
User Interface..............................................................................................7
Overview of the Mimic Diagram ...................................................................8
Menu Tree .................................................................................................9
UPS Configuration ....................................................................................10
View Measurements .................................................................................10
View Alarms.............................................................................................10
View Status..............................................................................................10
Configure Settings .................................................................................... 11
Configure the Personalization Functions............................................... 11
Configure Controls....................................................................................13
Configure the Synchronization Module (Option) ..........................................13
Controls Settings ................................................................................13
Source Type Settings ..........................................................................13
Operation ...................................................................................................14
Operating Modes......................................................................................14
Normal (Double Conversion) Mode ......................................................14
ECO Mode (Single UPS Only)..............................................................14
Frequency Converter Mode .................................................................14
Load on Battery Power ........................................................................14
Synchronization Module Modes (Option) ..............................................15
Operation Procedures...............................................................................16
UPS Breakers and Switches ................................................................16
Start Up a Single UPS on Input Source.................................................17
Start Up a Single UPS on Bypass Source .............................................18
Shut Down a Single UPS.....................................................................19
Restart a Single UPS ..........................................................................20
Shut Down a Parallel Configuration ......................................................21
Restart a Galaxy 5000 480 V Parallel Configuration...............................22
Restart a Galaxy 5500 400 V Parallel Configuration...............................23
Isolate the UPS...................................................................................24
Return the UPS to Normal Operation....................................................31
Operation of the Dry Contact Communication Card ............................37
Standard Mode.........................................................................................37
Programmable Mode ................................................................................38
List of Operating Status Conditions for Dry Contact Output
Relays ...............................................................................................38
Maintenance ..............................................................................................41
Life Cycle Monitoring (LCM) ......................................................................41
Servicing Batteries....................................................................................42
Troubleshooting ........................................................................................43
Identify the Alarms....................................................................................43
Synchronisation Module Alarms (Option)....................................................44
Alarm or Status Display Messages.............................................................44
990-5219B-001 3
Important Safety Instructions — SAVE
THESE INSTRUCTIONS 40–130 kVA 480 V,20–120 kVA 400 V
Important Safety Instructions — SAVE THESE
INSTRUCTIONS
Read these instructions carefully and look at the equipment to become familiar with
it before trying to install, operate, service or maintain it. The following safety
messages may appear throughout this manual or on the equipment to warn of
potential hazards or to call attention to information that clarifies or simplifies a
procedure.
The addition of this symbol to a “Danger” or “Warning” safety
message indicates that an electrical hazard exists which will result in
personal injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages with this symbol
to avoid possible injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in
death or serious injury.
Failure to follow these instructions will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
Failure to follow these instructions can result in injury or equipment
damage.
NOTICE
NOTICE is used to address practices not related to physical injury. The safety
alert symbol shall not be used with this type of safety message.
Failure to follow these instructions can result in equipment damage.
Please Note
Electrical equipment should only be installed, operated, serviced, and maintained
by qualified personnel. No responsibility is assumed by Schneider Electric for any
consequences arising out of the use of this material.
990-5219B-001 5
40–130 kVA 480 V,20–120 kVA 400 V
Important Safety Instructions — SAVE
THESE INSTRUCTIONS
A qualified person is one who has skills and knowledge related to the construction,
installation, and operation of electrical equipment and has received safety training
to recognize and avoid the hazards involved.
FCC Statement
NOTICE
RISK OF INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Failure to follow these instructions can result in equipment damage.
Safety Precautions
DANGER
HAZARD OF ELECTRICAL SHOCK, EXPLOSION OR ARC FLASH
All safety instructions in this document must be read, understood and followed.
Failure to follow these instructions will result in death or serious injury.
DANGER
HAZARD OF ELECTRICAL SHOCK, EXPLOSION OR ARC FLASH
After the UPS system has been electrically wired, do not start up the system.
Start-up must only be performed by Schneider Electric.
Failure to follow these instructions will result in death or serious injury.
6 990-5219B-001
User Interface 40–130 kVA 480 V,20–120 kVA 400 V
User Interface
Overview of the Display, the ON/OFF Buttons, and the Function
Keys
A. Help key
B. Function keys. Each key corresponds to a function presented on the display.
C. Menu key. Provides direct access to the main menu.
D. Inverter OFF button
E. Inverter ON button
NOTE: The display indicates the UPS operating status conditions and any alarms
and events related to the input source or the UPS as well as necessary corrective
action.
Overview of the Status LEDs
The status LEDs placed above the display shows the current status of the UPS
system:
The Load LED
The load LED is ON: The load is supplied and protected by the UPS.
990-5219B-001 7
40–130 kVA 480 V,20–120 kVA 400 V User Interface
The Warning Alarm LED
The warning alarm LED is ON: The load is supplied, but not protected by the UPS.
The Critical Alarm LED
The critical alarm LED is ON: The load is not protected. The load is either not
supplied or will reach the end of battery runtime very soon.
Overview of the Mimic Diagram
The mimic diagram shows the power flow through the UPS system, and the status
of the main functions. Each LED can be in one of the below three states:
• Green: The corresponding function is active and OK.
• Red: The corresponding function is not functioning properly.
• Off: The corresponding function is not active.
A. Input/PFC LED
B. Inverter LED
C. Battery LED
D. Load LED
E. Bypass LED
8 990-5219B-001
User Interface 40–130 kVA 480 V,20–120 kVA 400 V
Menu Tree
Measurements Battery measurements
Voltage measurements
Current measurements
Power measurements
Frequency measurements
Ratio measurements
Parallel measurements (optional)
Alarms
Status Time-stamped events
Statistics
Settings Language
Date and time
Contrast
Buzzer volume
Personalization
Output voltage
Password
Relay contacts
Controls Reset alarms
Inverter on
Inverter off
Force load transfer to inverter
Force load transfer to bypass
Desynchronize inverter from bypass
Resynchronize inverter and bypass
Test LEDs
Turn buzzer OFF
Enable LCM indications
Disable LCM indications
990-5219B-001 9
40–130 kVA 480 V,20–120 kVA 400 V UPS Configuration
UPS Configuration
View Measurements
1. Press the Menu key.
2. Use the function keys ↑ or ↓ to highlight Measurements on the display and
press the function key ← to select.
3. Use the function keys ↑ or ↓ to choose between the following measurements
and press the function key ← to select:
•Battery Measurements
•Voltage Measurements
•Current Measurements
•Power Measurements
•Frequency Measurements
•Ratio Measurements
•Parallel Measurements (optional)
View Alarms
Detailed information on all alarms is supplied on the display. See the Alarm or
Status Display Messages, page 44.
1. Press the Menu key.
2. Use the function keys ↑ or ↓ to highlight Alarms on the display and press the
function key ← to select.
3. Use the function keys ↑ or ↓ to choose between the alarm messages and press
the function key ← to select.
View Status
1. Press the Menu key.
2. Use the function keys ↑ or ↓ to highlight Status on the display and press the
function key ← to select.
3. Use the function keys ↑ or ↓ to choose between the following two status screens
and press the function key ← to select.
•Time-stamped events
•Statistics
10 990-5219B-001
UPS Configuration 40–130 kVA 480 V,20–120 kVA 400 V
Configure Settings
1. Press the Menu key.
2. Use the function keys ↑ or ↓ to highlight Settings on the display and press the
function key ← to select.
3. Use the function keys ↑ or ↓ to choose between the settings screens and press
the function key ← to select:
•Language
•Date and time
•Contrast
•Buzzer volume
•Personalization
•Output voltage
•Password
•Relay contacts
NOTE: The default password is set to:
Configure the Personalization Functions
NOTE: To configure personalization functions switches Q1 and Q5N must be in the
open (OFF) position and switches Q4S and Q3BP must be in the closed (ON)
position.
1. Press the Menu key.
2. Select Settings > Personalization by pressing the function keys ↑ or ↓ and
confirm by pressing the function key ←.
3. Enter the password by successively selecting each icon using the
corresponding function key and confirm by pressing the function key ←.
NOTE: The default password is set to:
990-5219B-001 11
40–130 kVA 480 V,20–120 kVA 400 V UPS Configuration
4. Select a personalization function by pressing the function keys ↑ or ↓ and
confirm by pressing the function key ←. Use the function keys ↑ , ↓, and ← to
change the settings. Available personalization functions are:
Operating Mode
Personalization Function Default Setting Available Settings
UPS operating mode NORMAL ECO
Automatic start Disabled Enabled
No. of auto starts after limiting 4 1 to 255
Auto start delay after limiting 4 seconds 1 to 60 seconds
Frequency
Personalization Function Default Setting Available Settings
Rated output frequency For 480 V: 60 Hz 60 Hz
400 V: 50 Hz
Bypass frequency tolerances 8 % 0.5 – 1 – 2 – 4 %
Inverter sync. rate 2 Hz / s 1 Hz / s
Automatic Bypass
Personalization Function Default Setting Available Settings
Transfer to bypass Enabled Disabled – disabled when limiting
Transfer to BP outside tol. Enabled Disabled
Battery
Personalization Function Default Setting Available Settings
% low battery warning voltage (if
battery monitor inactive)
40 % of remaining backup time 20 – 60 – 80 % of remaining
backup time
Low battery warning time (if
battery monitor active)
4 minutes of battery backup time 1 to X minutes of battery backup
time
Battery test interval 30 days 1 to 180 days
5. To save the settings, confirm by pressing the function key ←.
12 990-5219B-001
UPS Configuration 40–130 kVA 480 V,20–120 kVA 400 V
Configure Controls
1. Press the Menu key.
2. Use the function keys ↑ or ↓ to highlight Controls on the display and press the
function key ← to select.
3. Use the function keys ↑ or ↓ to choose between the controls screens and press
the function key ← to select:
•Reset Alarms
•Inverter on
•Inverter off
•Force load transfer to inverter
•Force load transfer to bypass
•Desynchronize inverter from bypass
•Resynchronize inverter and bypass
•Test LEDs
•Turn buzzer OFF
•Enable LCM indications
•Disable LCM indications
Configure the Synchronization Module (Option)
Controls Settings
Synchronization module controls are located in the synchronization module rear
panel.
Mode Preferred Master Source
Synchronization
Mode
Unit State
Automatic-source Reference
source1
Auto Enabled
Fixed-source Reference
source1
Fixed Enabled
Source Type Settings
Define UPS source type, between utility/mains or standby engine generator set, on
COSS board connector XM3:
Source Type Source 1 Source 2
Contact Between Pins
7 and 8
Contact Between Pins
9 and 10
Utility/mains Open Open
Engine generator set Closed Closed
990-5219B-001 13
1. If source S1 is selected, source S2 is controlled.
40–130 kVA 480 V,20–120 kVA 400 V Operation
Operation
Operating Modes
Normal (Double Conversion) Mode
When in normal mode, the UPS supports the load with conditioned power from the
input source.
The load LED is on.
ECO Mode (Single UPS Only)
The main advantage of ECO mode is a reduction in the consumption of electrical
power. In this mode, under normal conditions, the UPS operates continuously on
power from the bypass source. If the bypass mains goes outside tolerance, a
transfer to the inverter takes place. The load may experience a short duration
interruption of power (3 ms) during this transfer. When the bypass mains comes
back within tolerance, the load is again supplied with power from the bypass
source.
The load LED is ON.
Frequency Converter Mode
Frequency converter mode is a configuration without a bypass source connected.
When the power is turned on, the UPS starts up and goes automatically online to
supply the load with a frequency different from the input. Only the Galaxy 5500 400
V UPS can function as a frequency converter.
Load on Battery Power
If the utility/mains supply is missing, the UPS transfers to battery operation and
supports the load with conditioned power from the DC source.
The warning LED is ON and the buzzer sounds intermittently.
14 990-5219B-001
Operation 40–130 kVA 480 V,20–120 kVA 400 V
Synchronization Module Modes (Option)
The synchronization module synchronizes two or more power sources supplying a
static transfer switch. Two modes are available:
•Automatic-source mode: Both sources can be controlled.
•Fixed source mode: Only one source can be controlled.
When the UPS is controlled by the synchronization module, the warning alarm LED
is ON and the display shows this message: UPS on external synchronization.
On the synchronization module, the following LEDs are ON:
• The SYNCHRONISED SOURCE LED is ON. The phase deviation is within
tolerances. Sources are synchronized.
• The S2 CONTROLLED SOURCE LED is ON. Reference source is source S1.
Controlled source is source S2.
• The ACTIVATED LED is ON. Synchronization function is activated.
990-5219B-001 15
40–130 kVA 480 V,20–120 kVA 400 V Operation
Operation Procedures
UPS Breakers and Switches
480 V
Breakers and Switches
Q1 Input switch
Q4S Bypass switch
Q3BP Maintenance bypass switch
Q5N Output switch
400 V
Breakers and Switches
Q1 Input switch
Q4S Bypass switch
Q3BP Maintenance bypass switch
Q5N Output switch
QF1 Battery circuit breaker
16 990-5219B-001
Operation 40–130 kVA 480 V,20–120 kVA 400 V
Start Up a Single UPS on Input Source
1. Set the input switch Q1 to ON.
2. Set the battery circuit breaker:
– For 480 V: Set the battery circuit breaker of the auxiliary cabinets to ON.
– For 400 V: Set the battery circuit breaker QF1 (or the battery circuit breakers
of the auxiliary cabinets, if any) to ON.
3. Set the bypass switch Q4S to ON.
4. Set the output switch Q5N to ON.
5. Set the maintenance bypass switch Q3BP to OFF.
6. Press the Inverter ON button to start the UPS.
480 V 400 V
990-5219B-001 17
40–130 kVA 480 V,20–120 kVA 400 V Operation
Start Up a Single UPS on Bypass Source
1. Set the bypass switch Q4S to ON.
2. Set the output switch Q5N to ON.
3. Set the maintenance bypass switch Q3BP to OFF.
4. Set the input switch Q1 to ON.
5. Set the battery circuit breaker:
– For 480 V: Set the battery circuit breaker of the auxiliary cabinets to ON.
– For 400 V: Set the battery circuit breaker QF1 (or the battery circuit breakers
of the auxiliary cabinets, if any) to ON.
6. Press the Inverter ON button to start the UPS.
480 V 400 V
18 990-5219B-001
Operation 40–130 kVA 480 V,20–120 kVA 400 V
Shut Down a Single UPS
1. Press a random button on the display to exit sleep mode.
2. Press the Inverter OFF button for 3 seconds. The load is no longer protected
by the UPS. It is supplied via the bypass.
3. Set the battery circuit breaker:
– For 480 V: Set the battery circuit breaker of the auxiliary cabinets to OFF.
– For 400 V: Set the battery circuit breaker QF1 (or the battery circuit breakers
of the auxiliary cabinets, if any) to OFF
4. Set the input switch Q1 to OFF. The charger no longer operates to keep the
batteries fully charged.
5. Open the upstream circuit breakers of the input source and bypass sources to
completely power off the UPS.
480 V 400 V
990-5219B-001 19
40–130 kVA 480 V,20–120 kVA 400 V Operation
Restart a Single UPS
Check that switches Q4S and Q5N are closed. If this is the case, continue with this
procedure, otherwise refer to Return Single UPS to Normal Operation, page 31.
1. Set the input switch Q1 to ON.
2. Wait until the end of the UPS initialization with PFC start-up.
3. Set the battery circuit breaker:
– For 480 V: Set the battery circuit breaker of the auxiliary cabinets to ON.
– For 400 V: Set the battery circuit breaker QF1 (or the battery circuit breakers
of the auxiliary cabinets, if any) to ON.
4. Press the Inverter ON button to start the UPS.
The load is protected by the UPS.
If the load LED remains OFF and if the warning alarm LED or the critical alarm
LED is ON, see Identify the Alarms, page 43.
480 V 400 V
20 990-5219B-001
Operation 40–130 kVA 480 V,20–120 kVA 400 V
Shut Down a Parallel Configuration
1. Press a random button on each UPS display to exit sleep mode.
2. Press the Inverter OFF button on each UPS for 3 seconds. The load is no
longer protected by the UPSs. It is supplied via the bypass.
3. Set the battery circuit breaker:
– For 480 V: Set the battery circuit breakers of the auxiliary cabinets to OFF.
– For 400 V: Set the battery circuit breaker QF1 in each UPS (or the battery
circuit breakers of the auxiliary cabinets, if any) to OFF.
4. Set the input switch Q1 in each UPS to OFF. The charger no longer operates
to keep the batteries fully charged.
5. Open the upstream circuit breakers of the input and bypass sources to
completely power off the installation.
480 V 400 V
990-5219B-001 21
40–130 kVA 480 V,20–120 kVA 400 V Operation
Restart a Galaxy 5000 480 V Parallel Configuration
Check that switches Q4S and Q5N are closed. If this is the case, continue with this
procedure, otherwise see Return to Normal Operation, Parallel UPS Without
External Bypass Cabinet, page 32 or Return Galaxy 5000 480 V Parallel UPS with
External Bypass Cabinet to Normal Operation, page 35.
1. Check that the output switch CB2 in the external bypass cabinet is closed.
2. Check that the bypass switch CB1 in the external bypass cabinet is open.
Carry out steps 3 to 6 below on each of the UPSs.
3. Set the input switch Q1 to ON.
4. Wait until the end of the start sequence.
5. Set the battery circuit breaker of the auxiliary cabinets to ON.
6. Press the Inverter ON button to start the UPS.
On each UPS, the warning alarm LED and the critical alarm LED turn OFF and
the load LED turns ON. The load is protected by the UPSs.
If the load LED remains OFF and the warning alarm LED or the critical alarm
LED is ON, see Identify the Alarms, page 43.
22 990-5219B-001
Operation 40–130 kVA 480 V,20–120 kVA 400 V
Restart a Galaxy 5500 400 V Parallel Configuration
Check that switches Q4S and Q5N are closed. If this is the case, continue with this
procedure, otherwise refer to Return to Normal Operation, Parallel UPS Without
External Bypass Cabinet, page 32.
1. Check that the bypass switch Q4S in the external bypass cabinet is closed.
2. Check that the output switch Q5N in the external bypass cabinet is closed.
3. Check that the maintenance bypass switch Q3BP in the external bypass
cabinet is open.
Carry out steps 4 to 7 below on each of the UPSs.
4. Set the input switch Q1 to ON.
5. Wait until the end of the start sequence.
6. Set the battery circuit breaker QF1 (or the battery circuit breakers of the
auxiliary cabinets, if any) to ON.
7. Press the Inverter ON button to start the UPS.
On each UPS, the warning alarm LED and the critical alarm LED turn OFF and
the load LED turns ON. The load is protected by the UPSs.
If the load LED remains OFF and the warning alarm LED or the critical alarm
LED is ON, see Identify the Alarms, page 43.
990-5219B-001 23
40–130 kVA 480 V,20–120 kVA 400 V Operation
Isolate the UPS
Isolate a Single UPS
This procedure isolates the UPS from the electrical power source while the load is
supplied directly by the input or bypass source.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
After this operation, power will still be present on the power connection
terminals. Ensure that the protection covers are installed.
Failure to follow these instructions will result in death or serious injury.
1. Press a random button on the display to exit sleep mode.
2. Press the Inverter OFF button for 3 seconds to shut down the UPS. The load is
no longer protected by the UPS.
3. Set the maintenance bypass switch Q3BP to ON.
4. Set the output switch Q5N to OFF.
5. Set the battery circuit breaker:
– For 480 V: Set the battery circuit breaker of the auxiliary cabinets to OFF.
– For 400 V: Set the battery circuit breaker QF1 (or the battery circuit breakers
of the auxiliary cabinets, if any) to OFF.
6. Set the input switch Q1 to OFF.
7. Set the bypass switch Q4S to OFF.
8. Wait until the display and LEDs turn off.
The load is no longer protected by the UPS, but continues to be supplied
directly from the bypass source. UPS maintenance or servicing can now
be carried out.
480 V 400 V
Isolate a Galaxy 5500 400 V UPS Functioning as Frequency
Converter
1. Press a random button on the display to exit sleep mode.
24 990-5219B-001
Operation 40–130 kVA 480 V,20–120 kVA 400 V
2. Press the Inverter OFF button for 3 seconds to shut down the UPS. The load is
no longer protected by the UPS.
3. Set the battery circuit breaker QF1 (or the battery circuit breakers of the
auxiliary cabinets, if any) to OFF.
4. Set the input switch Q1 to OFF.
5. Open all Q4S and Q5N switches.
UPS maintenance can now be carried out.
Isolate a UPS Operating in ECO Mode
If supplied by the bypass source.
1. Check in the mimic diagram that the load is supplied by the bypass source. The
bypass LED must be on.
2. Set the maintenance bypass switch Q3BP to ON.
3. Set the output switch Q5N to OFF.
4. Set the battery circuit breaker:
– For 480 V: Set the battery circuit breaker of the auxiliary cabinets to OFF.
– For 400 V: Set the battery circuit breaker QF1 (or the battery circuit breakers
of the auxiliary cabinets, if any) to OFF.
5. Set the input switch Q1 to OFF.
990-5219B-001 25
40–130 kVA 480 V,20–120 kVA 400 V Operation
6. Set the bypass switch Q4S to OFF.
The load is no longer protected by the UPS, but continues to be supplied
directly from the bypass source. UPS maintenance or servicing can now
be carried out.
480 V 400 V
Isolate a Parallel System Without External Bypass Cabinet
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
After this operation, power will still be present on the power connection
terminals. Ensure that the protection covers are installed.
Failure to follow these instructions will result in death or serious injury.
1. Check that the two UPSs are operating.
2. Press a random button on the UPS 1 display to exit sleep mode.
3. Press the Inverter OFF button for 3 seconds to shut down UPS 1.
4. Set the output switch Q5N to OFF on UPS 1.
5. Set the battery circuit breaker:
– For 480 V: Set the battery circuit breakers of the auxiliary cabinets to OFF.
– For 400 V: Set the battery circuit breaker QF1 on UPS 1 (or the battery
circuit breakers of the auxiliary cabinets, if any) to OFF.
6. Set the input switch Q1 to OFF on UPS 1.
7. Set the bypass switch Q4S to OFF on UPS 1.
26 990-5219B-001
Operation 40–130 kVA 480 V,20–120 kVA 400 V
8. Wait until the display and LEDs turn off on UPS 1.
The load is still protected by the other UPS. Maintenance or servicing can
now be carried out on UPS 1.
480 V 400 V
9. Press a random button on the UPS 2 display to exit sleep mode.
10.Press the Inverter OFF button for 3 seconds to shut down UPS 2.
11.Set the maintenance bypass switch Q3BP to ON on UPS 2.
12.Set the output switch Q5N to OFF on UPS 2.
13.Set the battery circuit breaker:
– For 480 V: Set the battery circuit breakers of the auxiliary cabinets to OFF.
– For 400 V: Set the battery circuit breaker QF1 on UPS 2 (or the battery
circuit breakers of the auxiliary cabinets, if any) to OFF.
14.Set the input switch Q1 to OFF on UPS 2.
15.Set the bypass switch Q4S to OFF on UPS 2.
16.Wait until the display and LEDs turn off on UPS 2.
The load is no longer protected by the UPSs, but continues to be supplied
directly from the bypass source. Maintenance or servicing can now be
carried out on UPS 2.
480 V 400 V
990-5219B-001 27
40–130 kVA 480 V,20–120 kVA 400 V Operation
Isolate Parallel UPS With External Bypass Cabinet
Shut Down and Isolate One UPS in a Parallel System With
External Bypass Cabinet
1. Check that the total capacity of the remaining UPSs is sufficient to supply the
connected load.
2. Press a random button on the display on UPS 1 to exit sleep mode.
3. Press the Inverter OFF button for 3 seconds to shut down UPS 1.
4. Set the output switch Q5N to OFF on UPS 1.
5. Set the battery circuit breaker:
– For 480 V: Set the battery circuit breakers of the auxiliary cabinets to OFF.
– For 400 V: Set the battery circuit breaker QF1 on UPS 1 (or the battery
circuit breakers of the auxiliary cabinets, if any) to OFF.
6. Set the input switch Q1 to OFF on UPS 1.
7. Set the bypass switch Q4S to OFF on UPS 1.
8. Wait until the display and LEDs turn off on UPS 1.
The load is still protected by the other UPSs. Maintenance or servicing
can now be carried out on UPS 1.
480 V 400 V
Shut Down a Parallel System
Shut Down a Galaxy 5000 480 V Parallel System With External
Bypass Cabinet
1. On each UPS, press a random button on the display to exit sleep mode.
2. Press the Inverter OFF button for 3 seconds on each UPS to shut them down.
3. Depress the “transfer initiate” switch on the external bypass cabinet. Unlock
“KS” and remove key (G).
4. Insert key (G) into CB1. Unlock and close CB1.
5. Unlock and open CB2 and remove key (H).
6. Insert key (H) into key interlock “KS” and turn to lock.
7. Open output isolation CB11–CB16, as applicable, and open all Q5N switches of
each UPS.
8. Open the battery circuit breaker of each UPS.
28 990-5219B-001
Operation 40–130 kVA 480 V,20–120 kVA 400 V
9. Open Q1 and Q4S switches on each UPS.
10.Turn off all inputs to the UPSs.
11.Wait until the control electronics of all UPSs have fully shut down.
The load is no longer protected by the UPSs, but continues to be supplied
directly from the bypass source. UPS maintenance or servicing can now
be carried out.
External Bypass Cabinet
UPS Cabinet
Shut Down a Galaxy 5500 400 V Parallel System With External
Bypass Cabinet
1. On each UPS, press a random button to exit sleep mode.
990-5219B-001 29
40–130 kVA 480 V,20–120 kVA 400 V Operation
2. Press the Inverter OFF button for 3 seconds on each UPS to shut them down.
3. Set the Q3BP switch in the external bypass cabinet to ON.
4. Set the Q5N switch in the external bypass cabinet to OFF.
5. Set the Q4S switch in the external bypass cabinet to OFF.
6. Set the output switch Q5N on each UPS to OFF.
7. Set the battery circuit breaker QF1 (or the battery circuit breakers of the
auxiliary cabinets, if any) to OFF.
8. Set the input switch Q1 on each UPS to OFF.
9. Set the bypass switch Q4S on each UPS to OFF.
10.Wait until the control electronics of all UPSs have fully shut down.
The load is no longer protected by the UPSs, but continues to be supplied
directly from the bypass source. UPS maintenance or servicing can now
be carried out.
External Bypass Cabinet
UPS Cabinet
30 990-5219B-001
Operation 40–130 kVA 480 V,20–120 kVA 400 V
Return the UPS to Normal Operation
Return Single UPS to Normal Operation
1. Check that the maintenance bypass switch Q3BP is ON and that all other
switches are OFF.
2. Set the bypass switch Q4S to ON.
3. Set the output switch Q5N to ON.
4. Wait until the display turns on and check that there are no alarms on the static
switch on the bypass line.
5. Set the maintenance bypass switch Q3BP to OFF.
6. Set the input switch Q1 to ON.
7. Set the battery circuit breaker:
– For 480 V: Set the battery circuit breakers of the auxiliary cabinets to ON.
– For 400 V: Set the battery circuit breaker QF1 (or the battery circuit breakers
of the auxiliary cabinets, if any) to ON.
8. Press the Inverter ON button to start the UPS.
The load LED is ON.
If the load LED remains OFF and the warning alarm LED or the critical alarm
LED is ON, see Identify the Alarms, page 43.
480 V 400 V
Return a Galaxy 5500 400 V UPS Functioning as Frequency
Converter to Normal Operation
1. Check that all switches are OFF.
2. Set the bypass switch Q4S to ON (check that no cable is connected on phase
1, phase 2 and phase 3).
3. Set the input switch Q1 to ON.
4. Set the output switch Q5N to ON.
5. Set the battery circuit breaker QF1 (or the battery circuit breakers of the
auxiliary cabinets, if any) to ON.
990-5219B-001 31
40–130 kVA 480 V,20–120 kVA 400 V Operation
6. Press the Inverter ON button to start the UPS.
If the load LED remains OFF and the warning alarm LED or the critical alarm
LED is ON, see Identify the Alarms, page 43.
Return to Normal Operation, Parallel UPS Without External Bypass Cabinet
Restart a Parallel UPS Without External Bypass Cabinet with
Switch Q3BP ON and the Other Switches OFF
1. Set the bypass switch Q4S to ON.
2. Set the output switch Q5N to ON.
3. Check that the UPS is listed on the display, then press the function keys for
confirmation.
4. Set the maintenance bypass switch Q3BP to OFF.
5. Set the input switch Q1 to ON.
6. Set the battery circuit breaker:
– For 480 V: Set the battery circuit breaker of the auxiliary cabinets to ON.
– For 400 V: Set the battery circuit breaker QF1 (or the battery circuit breakers
of the auxiliary cabinets, if any) to ON.
32 990-5219B-001
Operation 40–130 kVA 480 V,20–120 kVA 400 V
7. Press the Inverter ON button to start the UPS.
The load LED is ON. The load is protected by the UPS.
If the load LED remains OFF and the warning alarm LED or the critical alarm
LED is ON, see Identify the Alarms, page 43.
480 V 400 V
Restart a Parallel UPS Without External Bypass Cabinet with All
Switches Set to OFF
1. Set the bypass switch Q4S to ON.
2. Set the output switch Q5N to ON.
3. Check that all the UPSs present in the installation are included in the list on the
display and press the function keys for confirmation.
4. Set the input switch Q1 to ON.
5. Set the battery circuit breaker:
– For 480 V: Set the battery circuit breaker of the auxiliary cabinets to ON.
– For 400 V: Set the battery circuit breaker QF1 (or the battery circuit breakers
of the auxiliary cabinets, if any) to ON.
990-5219B-001 33
Operation 40–130 kVA 480 V,20–120 kVA 400 V
Return to Normal Operation, Parallel UPS with External Bypass Cabinet
Return Galaxy 5000 480 V Parallel UPS with External Bypass
Cabinet to Normal Operation
1. Check that all switches on the UPSs are set to OFF.
2. Apply bypass and input power to the UPSs.
3. Set the bypass switch Q4S on each UPS to ON.
4. Set the output switch Q5N on each UPS and CB11–CB16 in the external
bypass cabinet, as applicable, to ON.
5. Check that all the UPSs present in the installation are included in the list on the
display and press the function key on each UPS for confirmation.
6. Set CB2 in the external bypass cabinet to ON.
7. Set CB1 in the external bypass cabinet to OFF.
8. Set the input switch Q1 on each UPS to ON.
9. Set the battery circuit breakers of the auxiliary cabinets to ON.
10.Press the Inverter ON button on each UPS to start the UPSs.
The load LED is ON. The load is protected by the UPSs.
If the load LED remains OFF and the warning alarm LED or the critical alarm
LED is ON, see Identify the Alarms, page 43.
Return Galaxy 5500 400 V Parallel UPS with External Bypass
Cabinet to Normal Operation
1. Check that all switches on the UPSs are set to OFF.
2. Set switch Q4S in the external bypass cabinet to ON.
3. Set the bypass switch Q4S on each UPS to ON.
4. Set the output switch Q5N on each UPS to ON.
5. Check that all the UPSs present in the installation are included in the list on the
display and press the function key on each UPS for confirmation.
6. Set switch Q5N in the external bypass cabinet to ON.
7. Set switch Q3BP in the external bypass cabinet to OFF.
8. Set the input switch Q1 on each UPS to ON.
9. Set the battery circuit breaker QF1 (or the battery circuit breakers of the
auxiliary cabinets, if any) on each UPS to ON.
990-5219B-001 35
Operation of the Dry Contact
Communication Card 40–130 kVA 480 V,20–120 kVA 400 V
Operation of the Dry Contact Communication Card
All systems are equipped with this dry contact communication card. Two inputs and
six outputs can be programmed.
NOTE: Only one dry contact communication card can be installed in a UPS.
Standard Mode
This system is compatible with all Schneider Electric systems that are I2C
compatible.
All SA1 microswitches must be set to OFF.
In this mode, the relays switch when the UPS changes status. The information
listed below is transmitted if the parameters are enabled.
Input
Contacts
Default Configuration Available Signals for Each Contact
1.A UPS ON •Battery room ventilation fault (temperature is out of tolerance
in the battery room)
•Transfer to bypass disabled
•Transfer to BP outside tol. disabled (transfer to bypass
disabled if the bypass source is out of tolerance)
•Inverter desynchronized with bypass (desynchronize UPS
with the bypass source)
1.B UPS OFF
Output
Relays
Default Configuration Available Signals for Each Contact
1.1 General alarm •Overload
•PFC fault
•Inverter fault
•Charger fault
•Automatic bypass fault
•Bypass source outside tolerances
•Battery temperature fault
•UPS fan fault
•EPO activated
•Battery circuit breaker open
•Phase rotation fault (phase inversion on input or bypass)
•Fuses blown
•Transfer to bypass disabled
•ECO mode activated
•Maintenance position (load on maintenance bypass)
1.2 Battery fault
1.3 Load on UPS
1.4 Load on automatic
bypass
1.5 Load on battery power
1.6 Low battery warning
Contacts are of the NO (normally open) type.
The general alarm can be tested by opening the battery circuit breaker.
Output relay assignments are configured using the UPS display: Settings > Relay
contacts.
990-5219B-001 37
40–130 kVA 480 V,20–120 kVA 400 V
Operation of the Dry Contact
Communication Card
Programmable Mode
The programmable mode is specific to the Galaxy 5500 UPS.
Microswitch 3 on SA1 must be set to ON.
In programmable mode, it is possible to assign operating status conditions to the
various dry contact output relays and predefined UPS commands to the SELV
inputs. Output relay assignments are configured using the UPS display: Settings >
Relay contacts.
List of Operating Status Conditions for Dry Contact Output Relays
Operating Status
Conditions
Description
GENERAL ALARM Abnormal presence of voltage on the output before closing the bypass static switch
(frequency converter) OR
ALIN board input fuse blown OR
Battery backup time ended, shift to wait mode OR
Battery deep discharge OR
Battery temperature out of tolerance> 45 ºC, charger shutdown OR
Bypass static switch inoperable OR
Charger inoperable OR
Charger shutdown due to battery room temperature outside tolerances OR
EPO activated OR
External Q3BP and external Q5N are closed simultaneously OR
Inverter inoperable OR
PFC inoperable OR
Q3BP and Q5N are closed simultaneously OR
Thermal overload on bypass OR
UPS in downgraded mode:
• External CAN communication inoperable OR
• Internal CAN communication inoperable (GDEN, MIZNUS and CHAN) OR
• CAN cable physically cut OR
• CAN communication relay inoperable OR
UPS personalization incorrect
BATTERY FAULT The battery will soon reach the end of its service life OR
Battery must be checked (battery check test was unsuccessful)
LOAD ON INVERTER Inverter connected to the load and operating on input. Battery operations due to a
BPI or battery test are signaled as operation on input.
LOAD ON AUTOMATIC
BYPASS
The static switch on the bypass is closed.
LOAD ON BATTERY
POWER
Inverter connected to the load and operating on battery power. Battery operations
due to a battery test are not signaled.
LOW BATTERY
WARNING
Battery has reached the low-battery warning level (voltage or time). The two
thresholds may be user set.
OVERLOAD One of the unit modules (rectifier, inverter, or bypass) is overloaded (thermal or
instantaneous).
PFC FAULT Neutral leg inoperable OR
Neutral leg IGBT temperature outside tolerances OR
• Voltage difference between 2 DC half-buses outside tolerances OR
38 990-5219B-001
Operation of the Dry Contact
Communication Card 40–130 kVA 480 V,20–120 kVA 400 V
Operating Status
Conditions
Description
• Top DC half-bus voltage outside tolerances OR
• Bottom DC half-bus voltage outside tolerances
PFC inoperable OR
• DC-bus voltage at end of CSR1 walk-in is lower than a threshold OR
• DC-bus voltage at end of DC walk-in is lower than a threshold OR
• DC-bus voltage is higher than the maximum threshold OR
◦DC-bus voltage is lower than the minimum threshold OR
◦Mean DC-bus voltage is higher than the maximum setpoint OR
• Mean DC-bus voltage is lower than the minimum setpoint OR
• DC-bus voltage is higher than the fast hardware threshold OR
• Temperature of the static switch on the AC normal outside tolerances OR
• Temperature of the battery static switch outside tolerances OR
• Rectifier is current limiting OR
• Rectifier thermal overload OR
PFC IGBT base-plate temperature outside tolerances OR
IGBT inductor temperature outside tolerances.
INVERTER FAULT Inverter short circuit detected OR
Inverter current limiting OR
Inverter static switch inoperable OR
Temperature out of tolerance on inverter static switch OR
Inverter base-plate temperature outside tolerances OR
Inverter thermal overload OR
Inverter phase-1 fuse has blown OR
Inverter phase-2 fuse has blown OR
Inverter phase-3 fuse has blown OR
Inverter phase-1 voltage amplitude outside tolerances OR
Inverter phase-2 voltage amplitude outside tolerances OR
Inverter phase-3 voltage amplitude outside tolerances OR
Instantaneous inverter voltage outside tolerances OR
Inverter relay for parallel connection is inoperable.
CHARGER FAULT Non-isolated supply on charger board inoperable OR
Isolated supply on charger board inoperable OR
Battery circuit breaker no. 1 inoperable OR
Battery circuit breaker no. 2 inoperable OR
Charger IGBT temperature outside tolerances OR
Difference in charge-current measurements between safety and measurement
systems OR
Charge current on measurement system close to zero OR
Charge current on safety system close to zero OR
Charge current is higher than safety level OR
Difference in voltage measurements between safety and measurement systems OR
Voltage on measurement system close to zero OR
Voltage on safety system close to zero OR
Battery voltage higher than safety level OR
Charger fuse blown.
990-5219B-001 39
40–130 kVA 480 V,20–120 kVA 400 V
Operation of the Dry Contact
Communication Card
Operating Status
Conditions
Description
AUTOMATIC BYPASS
FAULT
Supply unavailable for the static switch on the bypass source OR
Static switch inoperable on bypass OR
Temperature of the static switch on bypass outside tolerances.
BYPASS SOURCE
OUTSIDE
TOLERANCES
Bypass source outside of tolerances (voltage and/or frequency).
BATTERY
TEMPERATURE
FAULT
Battery ambient temperature outside tolerances.
UPS FAN FAULT Excessive temperature on one or more inductors OR
Inverter or bypass static switch fan inoperable.
EMERGENCY POWER
OFF ACTIVATED
EPO set on control-monitoring board OR
EPO set on charger board.
BATTERY CIRCUIT
BREAKER(S) OPEN
One or two battery circuit breakers is open.
PHASE ROTATION
FAULT
Phase inversion on input OR
Phase inversion on bypass.
FUSES BLOWN Fuse blown at input OR
Charger fuse has blown OR
Power supply board fuse has blown OR
Inverter phase-1 fuse has blown OR
Inverter phase-2 fuse has blown OR
Inverter phase-3 fuse has blown.
TRANSFER TO
BYPASS DISABLED
Transfer to bypass disabled (control and monitoring board checks for disabling by
the personalization and/or a dry contact input contact).
ECO MODE
ACTIVATED
The unit is operating in ECO mode. It is configured for ECO mode and the static
switch on the bypass is closed.
MAINTENANCE
POSITION
Output switch Q5N is open.
CHECK THE UPS A life cycle monitoring alarm has been activated:
• End of warranty
• End of AC capacitor service life
• End of DC capacitor service life
• End of fan service life
• End of power supply board service life
• End of battery service life
40 990-5219B-001
Maintenance 40–130 kVA 480 V,20–120 kVA 400 V
Maintenance
Life Cycle Monitoring (LCM)
The life cycle monitoring function provides UPS maintenance advice:
Display Message Description
End of warranty check recommended The end of the contractual legal warranty
Technical check recommended Regular maintenance requirements and the end of
service life for consumable components
Battery check required The end of the battery service life
In addition to these messages, the warning alarm LED turns on and the buzzer
sounds. These messages can be cleared by pressing the indicated function key.
This also causes the warning alarm LED to turn off, the buzzer to stop and
removes the installed external LED signalling box alarm (this alarm is optional).
You can disable the life cycle monitoring indications via the display by selecting
Controls > Disable LCM indications.
990-5219B-001 41
40–130 kVA 480 V,20–120 kVA 400 V Maintenance
Servicing Batteries
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
• Battery circuit breakers must be installed according to the specifications and
requirements as defined by Schneider Electric.
• Servicing of batteries must only be performed or supervised by qualified
personnel knowledgeable of batteries and the required precautions. Keep
unqualified personnel away from batteries.
• Do not dispose of batteries in a fire as they can explode.
• Do not open, alter, or mutilate batteries. Released electrolyte is harmful to the
skin and eyes. It may be toxic.
Failure to follow these instructions will result in death or serious injury.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Batteries can present a risk of electric shock and high short circuit current. The
following precautions must be observed when working on batteries
• Remove watches, rings, or other metal objects.
• Use tools with insulated handles.
• Wear protective glasses, gloves and boots.
• Do not lay tools or metal parts on top of batteries.
• Disconnect the charging source prior to connecting or disconnecting battery
terminals.
• Determine if the battery is inadvertently grounded. If inadvertently grounded,
remove source from ground. Contact with any part of a grounded battery can
result in electric shock. The likelihood of such shock can be reduced if such
grounds are removed during installation and maintenance (applicable to
equipment and remote battery supplies not having a grounded supply circuit).
Failure to follow these instructions will result in death or serious injury.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
When replacing batteries, always replace with the same type and number of
batteries or battery packs.
Failure to follow these instructions will result in death or serious injury.
42 990-5219B-001
Troubleshooting 40–130 kVA 480 V,20–120 kVA 400 V
Troubleshooting
Identify the Alarms
Identify the alarm conditions via the load LED, warning alarm LED, critical alarm
LED, and the buzzer.
Load LED Warning
alarm LED
Critical
alarm LED
Buzzer Description
--Intermittent Input source is not available
- - Intermittent UPS shuts down following end of battery
power
- - Intermittent UPS shuts down due to an alarm condition
that requires service from Schneider
Electric
- - Intermittent Bypass source is not available for ECO
mode and the UPS now operates in normal
mode supplied via the input source
--Intermittent Input and bypass sources are not available
for ECO mode and the UPS now supplies
the load from battery power
Detailed information on all alarms is supplied on the display.
• On the display, select the relevant alarm by using the function keys.
• Hold down the corresponding function key to display the possible causes of the
alarm and the required action.
990-5219B-001 43
40–130 kVA 480 V,20–120 kVA 400 V Troubleshooting
Synchronisation Module Alarms (Option)
SYNCHR-
ONISED
SOURCE
LED
INHIBITED
LED
Synchronization
function
Critical alarm
relay
Description
-Enabled Actuated Voltage is out of phase
-Disabled2-Voltage disappears
-
-
Disabled2Actuated Internal clock or sequencer is
inoperable
Alarm or Status Display Messages
Display Message Description Corrective Action
Abnormal bypass operation Abnormal bypass switch position Set to TEST or normal position
Abnormal external bypass
operation
Q3BP and Q5N have been closed
with the inverter connected to the
load
Abnormal presence of output
voltage
Abnormal presence of voltage on
the output before closing the
bypass static switch. UPS
operation impossible
AC Bypass static switch
thermal overload
The current supplied by the bypass
is greater than the rated current
Reduce the load on the bypass and
reset the fault
Battery circuit breaker 2 open
(QF2) (Battery Cabinet #2 or #4)
The battery circuit breaker QF2 is
open
Close the circuit breaker
Battery circuit breaker open
(QF1) (Battery Cabinet #1 or #3)
One of the battery circuit breakers
is open
Close the circuit breaker
44 990-5219B-001
2. Module stops controlling all UPSs and enters sleep mode.
Troubleshooting 40–130 kVA 480 V,20–120 kVA 400 V
Display Message Description Corrective Action
Battery deep discharge The battery has reached an
excessive discharge level. The
battery may be destroyed if
discharge continues
Shut down the UPS using the
Inverter OFF button. WARNING:
Check the deep discharge enable/
disable setting
Battery room temperature fault
Battery temperature fault The battery temperature has
reached a critical level
Check that the vents are not blocked
Battery test in progress An automatic periodic test battery
is in progress
Battery test result not OK One or more battery cells must be
checked
Bypass AC backfeed (KA2)
fault
The NORMAL AC backfeed
protection (KA2) is faulty
Check its power supply (fuse)
Bypass AC backfeed (KA2) is
open
The bypass AC backfeed (KA2) is
open
Bypass input phase rotation
fault
The bypass input phase sequence
is not Ph1, Ph2, Ph3
Check phase connections on the
bypass input terminal block
Bypass source outside
tolerances
The bypass input voltage is outside
tolerances
Check the bypass input source
Bypass source present Voltage is present on the bypass
input terminal block, but the UPS is
not configured for a bypass
Check UPS connections
Bypass static switch fault The bypass AC static switch is out
of order
Bypass static switch overload The current supplied by the bypass
is greater than the rated current
Reduce the load on the bypass
CAN communication relay fault Inter-UPS communication board
fault (relay on INTN). The UPS
cannot be connected in parallel
CAN communication
resynchronization fault
The installation reinitialization has
failed
Acknowledge the fault in order to
restart the installation initialization
Charger fault The battery charger is out of order.
It is no longer possible to recharge
the battery
Charger shutdown by PFC
overload
The battery charger has shut down
due to a PFC overload
To restart the charger, reduce the
load
Customer communication
disabled
The communication of UPS status
conditions to customer systems
has been disabled
Emergency Power Off (EPO) An EPO has been activated. The
load is no longer protected or,
depending on the settings, may no
longer be supplied
Deactivate the EPO
End of theoretical battery
service life
The battery will soon reach the end
of its theoretical service life
External sync frequency
outside tolerances
The external synchronization
frequency is outside tolerances
Check the signal connection
External CAN communication
fault
CAN communication fault between
installation UPSs. No sequence is
possible
UPS shutdown and isolation is
required
External Q3BP switch closed
(MBC or SBC CB1)
The external bypass switch is
closed. The load is not protected
Open the switch
990-5219B-001 45
40–130 kVA 480 V,20–120 kVA 400 V Troubleshooting
Display Message Description Corrective Action
External Q4S switch open (MBC
CB3)
The bypass source external switch
is open
To return to normal operation, use
the <Start-up procedure> menu
External Q5N switch open
(MBC or SBC CB2)
The external output switch is open Close the switch
Fan fault One of the fans is not operating
properly
Installation overload The supplied power is higher than
rated output of the UPS. The UPSs
are no longer redundant
Internal CAN communication
fault
The UPS has been isolated due to
an internal communication fault
Inverter and bypass
desynchronized
The inverter voltage is
desynchronized with respect to the
bypass input voltage
Check the bypass input source. A
bypass input desync command may
have been issued or the inverter may
be starting; please wait a few
seconds
Inverter current limiting An overload has been detected; the
UPS is supplying the additional
load
Reduce the load
Inverter fault The inverter is out of order. The
load is no longer protected
Inverter fuse blown One of the inverter fuses has blown Replace the fuse
Inverter overload The current supplied by the UPS is
greater than the rated current
Reduce the load
Inverter ready for load
connection
Inverter operational
Inverter starting
Inverter thermal overload The current supplied by the UPS is
greater than the rated current
Reduce the load
Load short circuit A short circuit has been detected
on the UPS output
Check the UPS load
Loss of communication with
UPS 1
UPS 1 in the installation is no
longer detected
Check the CAN bus connections
Loss of communication with
UPS 2
UPS 2 in the installation is no
longer detected
Check the CAN bus connections
Loss of communication with
UPS 3
UPS 3 in the installation is no
longer detected
Check the CAN bus connections
Loss of communication with
UPS 4
UPS 4 in the installation is no
longer detected
Check the CAN bus connections
Loss of communication with
UPS X
One of the UPSs in the installation
is no longer detected
Check the CAN bus connections
Low battery shutdown The battery is too low to power the
load. A battery charge cycle will
begin when AC power is restored
Check normal AC source
Low battery warning The remaining battery power
depends on the setting for the low
battery warning threshold
Non-redundant installation No redundancy available. If one
UPS shuts down, the load will no
longer be protected
Reduce the load level or add another
UPS
46 990-5219B-001
Troubleshooting 40–130 kVA 480 V,20–120 kVA 400 V
Display Message Description Corrective Action
Normal AC backfeed (KA1) fault The NORMAL AC backfeed
protection (KA1) is faulty
Check its power supply (fuse)
Normal AC backfeed (KA1) is
open
The NORMAL AC backfeed
protection (KA1) is open
Normal AC fuse blown The fuses protecting the normal AC
input have blown
Replace the fuses
Normal AC input phase rotation
fault
The normal AC input phase
sequence is not Ph1, Ph2, Ph3
Check the phase connections on the
normal AC input terminal block
Normal AC source downgraded The voltage at the normal AC input
is low. The UPS cannot supply full
rated load
Check the normal AC source
Normal AC source outside
tolerances
The normal AC input voltage is
outside tolerances
Check the normal AC input source
Normal AC source static switch
failure
The normal AC source static switch
is faulty
Not enough bypass static
switches
The number of units ready is less
than the “enough inverters for load
connection” criteria
Start another unit
Not enough inverters for load
connection
The number of units ready is less
than the “enough inverters for load
connection” criteria
Start another inverter
Personalization does not match
UPS
The UPS personalization settings
do not match the actual
characteristics of the UPS
PFC fault The PFC is out of order. The load is
no longer protected
PFC overload The power drawn by the PFC is
greater than the rated power
Reduce the load
PFC thermal overload The current supplied by the UPS is
greater than the rated current
Reduce the load
Power supply board fuse blown The DC power supply fuse has
blown
Replace the fuse
Q1 switch open The normal AC input switch is open Close the switch to supply the UPS
Q4S switch open The bypass input switch is open To return to normal position, use the
<Start-up procedure> menu
Q5N switch open The UPS output switch is open Set it to Normal position
Resynchronizing Reinitializing the installation.
Please wait...
Starting PFC starting
Transfer to bypass disabled Load transfer to the bypass has
been disabled by UPS settings, a
dry contact input or because the
UPS is in downgraded mode
TVSS fault The transient voltage surge
suppressor is faulty
It’s necessary to check it
UPSs not connected by CAN
cable
The CAN communication cable
between UPSs is disconnected or
improperly connected
Check the connections (cables and
terminators)
990-5219B-001 47
40–130 kVA 480 V,20–120 kVA 400 V Troubleshooting
Display Message Description Corrective Action
UPS on external
synchronization
The UPS is not synchronized on
Bypass AC, but on external
synchronization
UPS personalization fault The UPS personalization failed Power off the unit and send the
personalization again
48 990-5219B-001
Schneider Electric
35 rue Joseph Monier
92500 Rueil Malmason
France
+ 33 (0) 1 41 29 70 00
www.schneider-electric.com
As standards, specifications, and design change from time to time,
please ask for confirmation of the information given in this publication.
© 2013 – 2016 Schneider Electric. All rights reserved.
990-5219B-001