APC SMT3000RM2UNC User Manual
Displayed below is the user manual for SMT3000RM2UNC by APC which is a product in the Uninterruptible Power Supplies (UPSs) category. This manual has pages.
Related Manuals
Installation Guide Smart-UPS™
750/1000/1500/2200/3000 VA 100/120/230 Vac
Rack-Mount 2U
Important Safety Messages
Read the instructions carefully to become familiar with the equipment before trying to install, operate, service or
maintain it. The following special messages may appear throughout this man ual or on the equipment to warn of
potential hazards or to call att ention to information that clarifies or simplifies a procedure.
The addition of this symbol to a Caution product safety label indicates that an electrical hazard exists
which will result in personal injury if the inst ructions are not followed.
The following safety messages may appear throughout this manual to warn of potential
hazards.
Safety and General Information
Inspect the package contents upon receipt. Notify the carrier and dealer if there is any damage.
Read the Safety Guide supplied with this unit before installing the UPS.
• Adhere to all national and local electrical codes.
• This UPS is intended for indoor use only.
• Do not operate this UPS in direct sunlight, in contact with fluids, or where there is excessive dust or
humidity.
• Be sure the air vents on the UPS are not blocked. Allow adequate space for proper ventilation.
• The battery typically lasts for two to five years. Environmental factors impact battery life. Elevated ambient
temperatures, poor quality utility power, and frequent short duration disch a rges will shorten battery life.
• Connect the UPS power cable directly to a w all outlet. Do not use surge protectors or extension cords.
• The equipment is heavy. Always practice safe lifting techniques adequate for the weight of the equipment.
• The batteries are heavy. Remove the batteries before installing the UPS and XLBP in a rack.
• Always install external battery packs (XLBPs) at the bottom in rack-mount or stack configurations. The UPS
must be installed above the X L BPs.
• Always install peripheral equipment above the UPS in rack-mount or stack configurations.
• The UPS will recognize as many as 10 external battery packs connected to the UPS. However there is no
limit to the number of XLBPs th at can be used with the UPS.
• The model and serial numbers are located on a small, rear panel label. For some models, an additional label is
located on the chassis under the front bezel.
• Always recycle used batt eries.
• Recycle the package materials or save them for reuse.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, can result in equipment damage and minor or
moderate injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, can result in equipment damage.
Smart-UPS 750/1000/1500/2200/3000 VA 120/208/230 Vac Rack-Mount 2U2
Inventory
Installation
All models 2200/3000 VA models
(1) (1) (1) (1)
120/208/230 Vac models
(1) (1) (1)
230 Vac models
(2) (1)
2200/3000 VA models (1)
2200/3000 VA models (1)
2200/3000 VA models
CAUTION
DAMA G E TO EQUIPMENT OR PERSONN EL
• The equipment is heavy. Always practice safe lifting techniques adequate for the weight of the equipment.
• Remove the battery before installing the UPS in a rack.
• When installing equipment in a rack, always install the UPS at the bottom of the rack with the peripheral
equipment above the UPS.
• The UPS should always be installed below peripheral equipment in stack or rack configurations.
Failure to follow these instructions can result in equipment damage and minor or moderate injury
Smart-UPS 750/1000/1500/2200/3000 VA 120/208/230 Vac Rack-Mount 2U 3
750 VA models
su0648a
su0649a
su0651a
su0660a
su0440a
su
0469a
bu059a
su0652a
su0659a
su0563a
Smart-UPS 750/1000/1500/2200/3000 VA 120/208/230 Vac Rack-Mount 2U4
1000/1500 VA models
su0657a
su0661a
su0660a
su0440a
su
0469a
su0629a
su0631a
su0658a
su0630a
Smart-UPS 750/1000/1500/2200/3000 VA 120/208/230 Vac Rack-Mount 2U 5
2200/3000 VA models
GRAPHIC OF CONNECTING THE BATTERY
su0654a
su0661a
su0660a
su0440a
su
0469a
su0629a
su0656a
su0655a
su0630a
Smart-UPS 750/1000/1500/2200/3000 VA 120/208/230 Vac Rack-Mount 2U6
Overview and Start Up
Rear panel fe atures
SmartSlot for optional NMC accessory card
UPS input
Circuit brea ker/Overload prote ction
Control le d outl e t gr oup
Chassis ground screw
Outlets
EPO connector
USB port
RJ45 connector - UPS monitoring serial port
750/1000 VA 120 Vac
1500 VA 100/120 Vac 3000 VA 100/120 Vac
750/1000/1500 VA 230 Vac 3000 VA 208 Vac
2200 VA 120 Vac 2200/3000 VA 230 Vac
su064
4a
su062
4a
su064
5a
su0625
a
su0623a
su0626
a
Smart-UPS 750/1000/1500/2200/3000 VA 120/208/230 Vac Rack-Mount 2U 7
Electrical connections
Plug type and connector locations may vary.
CAUTION
DAMAGE TO EQUIPM ENT OR PERSONNEL
• Adhere to all local and national electrical codes.
• Wiring should be performed by qualified electrician.
• Always connect the UPS t o a grounded outlet.
Failure to follow these instructions can result in equipment damage and minor or moderate injury
su0628a
© 2014 APC by Schneider Electric. APC, the APC logo, an d Smart-UPS are owned by Schneider
Electric Indu stries S.A.S., or their affiliated companies. All othe r trademarks are property of their
respective owners.
EN 990-3892C
10/2014
Display panel features
Cont rolled outlet gr oups
Some UPS models have one bank of outlets that can function as a controlled group. Use the display
interface to configure the controlled outlet features, navigate to:
Main Menu > Control > Outlet1 Control.
Select models are ENERGY STAR® qualified.
For more information go to www.apc.com/site/recycle/index.cfm/energy-efficiency/energy-star/
Online LED
UPS ON/OFF key
On Battery LED
Site Wiring Fault LED
Replace Battery LED
Display interface
UP/DOWN arrow keys
ENTER key
ESCAPE key
su0343a
APC By Schneide r
Electric