Table of Contents
- Contents
- Notices
- Safety information
- Care & Cleaning
- Takeback Services
- Chapter 1: Product introduction
- 1.1 Welcome!
- 1.2 Package contents
- 1.3 Monitor introduction
- Chapter 2: Setup
- 2.1 Assembling the monitor arm/base
- 2.2 Detaching the arm/base (for VESA wall mount)
- 2.3 Attaching/Removing the MiniPC Kit (BE209/BE229/BE239/BE249/BE24A/BE24W/BE27A height adjustment base)
- 2.4 Adjusting the monitor
- 2.5 Connecting the cables
- 2.6 Turning on the monitor
- Chapter 3: General instructions
- 3.1 OSD (On-Screen Display) menu
- 3.2 Specifications summary
- 3.3 Troubleshooting (FAQ)
- 3.4 Supported operating modes
ASUS BE24WQLB User Manual
Displayed below is the user manual for BE24WQLB by ASUS which is a product in the Computer Monitors category. This manual has pages.
Related Manuals
BE209/BE229/BE239/
BE249/BE24A/BE24W/
BE27A Series LCD
Monitor
User Guide
ii
First Edition
June 2015
Copyright © 2015 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless
such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM
ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN
THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the
owners’ benet, without intent to infringe.
iii
Contents
1.3.1 Front view ....................................................................... 1-2
1.3.2 Back view ........................................................................ 1-4
1.3.3 QuickFit Function ............................................................ 1-6
3.1.1 How to recongure .......................................................... 3-1
3.1.2 OSD function introduction ............................................... 3-2
iv
Notices
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modications
to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
As an Energy Star® Partner, our company has determined that this
product meets the Energy Star® guidelines for energy efciency.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
This Class B digital apparatus meets all requirements of the Canadian
Interference - Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Réglement sur le matériel brouiller du Canada.
v
A third-party certification according to ISO 14024
Say hello
to a more sustainable product
IT products are associated with a wide range of sustainability risks
throughout their life cycle. Human rights violations are common in the
factories. Harmful substances are used both in products and their
manufacture. Products can often have a short lifespan because of poor
ergonomics, low quality and when they are not able to be repaired or
upgraded.
This product is a better choice. It meets all the criteria in TCO Certified,
the world’s most comprehensive sustainability certification for IT
products. Thank you for making a responsible product choice, that help
drive progress towards a more sustainable future!
Criteria in TCO Certified have a life-cycle perspective and balance
environmental and social responsibility. Conformity is verified by
independent and approved verifiers that specialize in IT products, social
responsibility or other sustainability issues. Verification is done both
before and after the certificate is issued, covering the entire validity
period. The process also includes ensuring that corrective actions are
implemented in all cases of factory non-conformities. And last but not
least, to make sure that the certification and independent verification is
accurate, both TCO Certified and the verifiers are reviewed regularly.
Want to know more?
Read information about TCO Certified, full criteria documents, news and
updates at tcocertified.com. On the website you’ll also find our Product
Finder, which presents a complete, searchable listing of certified
products.
Toward sustainable IT products
vi
Safety information
• Before setting up the monitor, carefully read all the documentation that came
with the package.
• To prevent re or shock hazard, never expose the monitor to rain or moisture.
• Never try to open the monitor cabinet. The dangerous high voltages inside the
monitor may result in serious physical injury.
• If the power supply is broken, do not try to x it by yourself. Contact a qualied
service technician or your retailer.
• Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
• Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or over a
radiator or heat source unless proper ventilation is provided.
• The monitor should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.
• Use the appropriate power plug which complies with your local power standard.
• Do not overload power strips and extention cords. Overloading can result in re
or electric shock.
• Avoid dust, humidity, and temperature extremes. Do not place the monitor in
any area where it may become wet. Place the monitor on a stable surface.
• Unplug the unit during a lightning storm or if it will not be used for a long period
of time. This will protect the monitor from damage due to power surges.
• Never push objects or spill liquid of any kind into the slots on the monitor
cabinet.
• To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate congured receptacles marked between
100-240V AC.
• If you encounter technical problems with the monitor, contact a qualied
service technician or your retailer.
• Adjustment of the volume control as well as the equalizer to other settings
than the center position may increase the ear-/headphones output voltage and
therefore the sound pressure level.
This symbol of the crossed out wheeled bin indicates that the product (electrical,
electronic equipment, and mercury-containing button cell battery) should not
be placed in municipal waste. Please check local regulations for disposal of
electronic products.
vii
Care & Cleaning
• Before you lift or reposition your monitor, it is better to disconnect the cables
and power cord. Follow the correct lifting techniques when positioning the
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.
Do not lift the display by the stand or the cord.
• Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed
with a cloth dampened with mild cleaner.
• Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended
for use with the monitor. Never spray cleaner directly on the screen, as it may
drip inside the monitor and cause an electric shock.
• You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
• When the same image is displayed for hours, an afterimage of the previous
screen may remain after switching the image. The screen will recover slowly or
you can turn off the Power Switch for hours.
• When the screen becomes black or ashes, or cannot work anymore, contact
your dealer or service center to x it. Do not repair the screen by yourself!
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying
to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
viii
Refer to the following sources for additional information and for product and
software updates.
The ASUS websites worldwide provide updated information on ASUS
hardware and software products. Refer to http://www.asus.com
Your product package may include optional documentation that may have
been added by your dealer. These documents are not part of the standard
package.
Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest
standards for protecting our environment. We believe in providing solutions for
our customers to be able to responsibly recycle our products, batteries and other
components as well as the packaging materials.
Please go to http://csr.asus.com/english/Takeback.htm for detail recycling
information in different region.
1-1ASUS BE Series LCD Monitor
1.1 Welcome!
Thank you for purchasing the ASUS® LCD monitor!
The latest widescreen LCD monitor from ASUS provides a broader, brighter and
crystal-clear display, plus a host of features that enhance your viewing experience.
With these features, you can enjoy the convenience and delightful visual
experience that the monitor brings to you!
1.2 Package contents
Check your package for the following items:
LCD monitor
Monitor base
Quick start guide
Warranty card
Power cord
DVI cable (for selected models)
HDMI cable (for selected models)
DisplayPort cable (for selected models)
DisplayPort cable (Mini-DP to DP) (for selected models)
VGA cable (for selected models)
USB cable (for selected models)
Audio cable
MiniPC Kit (for selected models)
If any of the above items is damaged or missing, contact your retailer
immediately.
1-2 Chapter 1: Product introduction
1.3 Monitor introduction
Menu
Close
Quick Fit
Brightness
Blue Light Filter
Menu
Close
Quick Fit
Brightness
Blue Light Filter
7
1234
5
6
BE229/BE239/BE249 simple base BE209/BE229/BE239/BE249/BE24A/
BE24W/BE27A height adjustment base
1. Power button/power indicator
• Turns the monitor on/off.
• The color denition of the power indicator is as the below table.
White On
Amber Standby mode
Off Off
2. Menu button:
• Press this button to display the OSD menu when the OSD is off.
• Enters the OSD menu.
• Toggles the Key Lock function between on and off with a long press for
5 seconds.
3. Close button:
• Press this button to display the OSD menu when the OSD is off.
• Exits the OSD menu.
4. QuickFit button:
• Press this button to display the OSD menu when the OSD is off.
• This is a hotkey to activate the QuickFit function designed for alignment.
1-3ASUS BE Series LCD Monitor
• The QuickFit function contains pages of common grid patterns, paper
sizes, and photo sizes. (Please refer to 1.3.3 QuickFit Function).
5. Shortcut
• Press this button to display the OSD menu when the OSD is off.
• Default: Brightness hotkey
• To change the hotkey function, go to the Shortcut > Shortcut 1 menu.
6. Shortcut
• Press this button to display the OSD menu when the OSD is off.
• Default: Blue light lter hotkey
• To change the hotkey function, go to the Shortcut > Shortcut 2 menu.
7. Human Sensor (only for BE239QLBR):
• Detects user’s presence in front of the monitor screen. The monitor
automatically enters standby mode when no moving object in front of
the monitor is detected for longer than 60 seconds. When the user
comes back, the power resumes automatically when it detects the
user’s presence. The default setting of Human sensor is “Off”. User can
activate this function through OSD settings.
1-4 Chapter 1: Product introduction
BE229QB/BE239QB/
BE249QB
10
1234 5 678 9
BE229Q/BE239Q/BE249Q
1234 5 678
BE229QBH
BE229QH
10
1234 5
78
11
6 9
1234 5
78
11
6
BE209TLB
10
1235679
BE209QLB/BE229QLB/
BE239QLB/BE239QLBR/
BE249QLB/BE24AQLB
10
1234 5 678 9
BE209TL
123567
BE209QL/BE229QL/
BE239QL/BE249QL
1234 5 678
1-5ASUS BE Series LCD Monitor
BE27AQLB
10
10
1234
578 9
11 10
12
BE229QLBH/BE239QLBH/
BE249QLBH/BE24AQLBH
1234 5
78
11
6 9
BE24WQLB
10
1234
78
11
6 9
10
.
. Press the switch to turn on/off power.
. This port connects the power cord.
. This port is for connection with a DisplayPort compatible
device.
. This 24-pin port is for PC (Personal Computer) DVI-D digital signal
connection.
. This 15-pin port is for PC VGA connection.
. This port connects PC audio source by the bundled audio
cable.
. This port is only available when an HDMI/DisplayPort cable
is connected.
. This port is for connection with a USB upstream cable.
The connection enables the USB ports on the monitor.
. These ports are for connection with USB devices,
such as USB keyboard/mouse, USB ash drive, etc.
This port is for connection with an HDMI compatible device.
This port is for connection with a Mini DisplayPort
compatible device.
1-6 Chapter 1: Product introduction
The QuickFit function contains three kinds of patterns: (1) Grid patterns (2) Paper
size (3) Photo size. To activate the patterns, press the QuickFit button. Press the
buttons as indicated on the screen to select a desired pattern.
Some of the following patterns may not be available. Please refer to the actual
patterns shown on your monitor.
1. Grid patterns
The grid patterns facilitate users to efciently organize and compare various
contents, such as spreadsheet viewing and photo editing.
Alignment Grid 1 Alignment Grid 2
Alignment Grid 1 Alignment Grid 2
2. Paper size
QuickFit provides several commonly used standard paper sizes for users to view
their documents in real size on the screen.
A4 B5
A4
B5
Letter
Letter
1-7ASUS BE Series LCD Monitor
3. Photo size
The various real photo sizes displayed in the QuickFit function provides
photographers and other users to accurately view and edit their photos in real size
on the screen.
Photo 4x6, 3x5, 2x2 Photo 8x10, 5x7
3x5 2x2
4x6 5x7
8x10
1-8 Chapter 1: Product introduction
2-1ASUS BE Series LCD Monitor
2.1 Assembling the monitor arm/base
To assemble the monitor base:
1. Have the front of the monitor face down on a table.
2. Attach the base into the arm, making sure the tab on the arm ts into the
groove on the base.
3. Fix the base to the arm by fastening the bundled screw.
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
BE229/BE239/BE249 simple base
BE209/BE229/BE239/BE249/BE24A/BE24W/BE27A
height adjustment base
2.2 Detaching the arm/base
(for VESA wall mount)
The detachable arm/base of this monitor is specially designed for VESA wall mount.
To detach the arm/base:
2-2 Chapter 2: Setup
BE229/BE239/BE249 simple base
1. Have the front of the monitor face down on a table.
2. Remove the rubbers in the four screw holes. (Figure 1)
3. Remove the base (Figure 2).
4. Use a screwdriver to remove the screw on the hinge (Figure 3), then remove
the hinge.
1
2
(Figure 1) (Figure 2)
1
2
(Figure 3)
BE209/BE229/BE239/BE249/BE24A/BE24W/BE27A
height adjustment base
1. Have the front of the monitor face down on a table.
2. Press the release button, and then detach the arm/base from the monitor (Figure
2).
2
1
(Figure 1) (Figure 2)
2-3ASUS BE Series LCD Monitor
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
• The VESA wall mount kit (100 x 100 mm) is purchased separately.
• Use only the UL Listed Wall Mount Bracket with minimum weight/load
22.7kg (Screw size: M4 x 10 mm)
2.3 Attaching/Removing the MiniPC Kit
(BE209/BE229/BE239/BE249/BE24A/
BE24W/BE27A height adjustment
base)
Attaching the MiniPC Kit
2
1
Removing the MiniPC Kit
2
1
2-4 Chapter 2: Setup
2.4 Adjusting the monitor
• For optimal viewing, we recommend that you look at the full face of the
monitor, then adjust the monitor to the angle that is most comfortable for you.
• Hold the stand to prevent the monitor from falling when you change its angle.
• BE229/BE239/BE249 simple base: The recommended adjusting angle is +20
to -5˚.
• BE209/BE229/BE239/BE249/BE24A/BE24W height adjustment base: You can
adjust the monitor’s angle from +35˚ to -5˚and it allows 90˚ swivel adjustment
from either left or right. You can also adjust the monitor’s height within +/- 130
mm.
• BE27A height adjustment base: You can adjust the monitor’s angle from +35˚
to -5˚and it allows 90˚ swivel adjustment from either left or right. You can also
adjust the monitor’s height within +/- 150 mm.
(Tilt)
(Swivel) (Height adjustment)
(Tilt)
90° 0°
90°
simple base
-5° ~ +20°
height adjustment base
-90° ~ +90°
height adjustment base
150mm
130mm
(only for BE27A)
-5° ~ +35°
height adjustment base
1. Lift the monitor to the highest position.
2. Tilt the monitor to its maximum angle.
3. Pivot the monitor clockwise/counterclockwise to the angle you need.
2-5ASUS BE Series LCD Monitor
It is normal that the monitor slightly shakes while you adjust the viewing angle.
2.5 Connecting the cables
Connect the cables as the following instructions:
: Connect one end of the power cord securely to
the monitor’s AC input port, the other end to a power outlet.
:
a. Plug one end of the VGA/DVI/DisplayPort/HDMI/Mini DisplayPort cable
to the monitor’s VGA/DVI/DisplayPort/HDMI/Mini DisplayPort jack.
b. Connect the other end of the VGA/DVI/DisplayPort/HDMI/Mini
DisplayPort cable to your computer's VGA/DVI/DisplayPort/HDMI/Mini
DisplayPort jack.
c. Tighten the two screws to secure the VGA/DVI connector.
2-6 Chapter 2: Setup
connect one end of the audio cable to the
monitor’s Audio-in port, the other end to the computer’s audio-out port.
connect the end with plug type to the monitor’s
earphone jack when an HDMI or DisplayPort signal is fed.
: Take the supplied USB 2.0 cable, and plug
the smaller end (type B) of the USB upstream cable to the monitor’s USB
upstream port, and the larger end (type A) to your computer’s USB 2.0 port.
Make sure your computer is installed with the lastest Windows 7/Windows 8
operating system. That will enable the USB ports on the monitor to work.
: Take the supplied USB 3.0 cable, and plug
the smaller end (type B) of the USB upstream cable to the monitor’s USB
upstream port, and the larger end (type A) to your computer’s USB 3.0 port.
Make sure your computer is installed with the lastest Windows 7/Windows 8.1/
Windows 10 operating system. That will enable the USB ports on the monitor
to work.
When these cables are connected, you can choose the desired signal
from the Input Select item in the OSD menu.
2.6 Turning on the monitor
Press the power button . See page 1-2 for the location of the power button. The
power indicator lights up in white to show that the monitor is ON.
3-1ASUS BE Series LCD Monitor
3.1 OSD (On-Screen Display) menu
3.1.1 How to reconfigure
Splendid
ASUS BE229
Standard Mode VGA 1920 x 1080 @ 60Hz
Scenery Mode
Standard Mode
Theater Mode
Night View Mode
sRGB Mode
Reading Mode
Darkroom Mode
1. Press any button (except the Power button) to display the OSD menu.
2. Press the Menu button to activate the OSD menu.
3. Press the buttons as indicated on the screen to navigate through the
functions. Highlight the desired function and press to activate it. If the
function selected has a sub-menu, press and again to navigate
through the sub-menu functions. Highlight the desired sub-menu function and
press to activate it.
4. Press and to change the settings of the selected function.
5. To exit and save the OSD menu, press or repeatedly until the OSD menu
disappears. To adjust other functions, repeat steps 1-4.
3-2 Chapter 3: OSD (On-Screen Display) menu
3.1.2 OSD function introduction
This function contains 7~8 sub-functions you can select for your preference.
Each mode has the Reset selection, allowing you to maintain your setting or
return to the preset mode.
Splendid ASUS BE229
Standard Mode VGA 1920 x 1080 @ 60Hz
Scenery Mode
Standard Mode
Theater Mode
Night View Mode
sRGB Mode
Reading Mode
Darkroom Mode
Scenery Mode
Standard Mode
Theater Mode
Game Mode
Night View Mode
sRGB Mode
Reading Mode
Darkroom Mode
Splendid ASUS BE27A
Standard Mode DisplayPort 2560 x 1440 @ 60Hz
Best choice for scenery photo display with SplendidPlus
Video Enhancement.
: Best choice for document editing with SplendidPlus
Video Enhancement.
Best choice for movies with SplendidPlus Video
Enhancement.
: Best choice for games playing
with SplendidPlus Video Enhancement.
Best choice for dark-scene games or movies with
SplendidPlus Video Enhancement.
: best choice for viewing photos and graphics from PCs.
3-3ASUS BE Series LCD Monitor
: This is the best choice for book reading.
: This is the best choice for a weak ambient light
environment.
• In the Standard mode, the following function(s) are not user-configurable:
Saturation, Skin Tone, Sharpness, ASCR.
• In the sRGB mode, the following function(s) are not user-configurable:
Brightness, Contrast, Saturation, Color Temp., Skin Tone, Sharpness,
ASCR.
• In the Reading mode, the following function(s) are not user-congurable:
Contrast, Saturation, Color Temp., Skin Tone, Sharpness, ASCR.
In this function, you can adjust the blue light filter level.
Level 0
Level 1
Level 2
Level 3
Level 4
Blue Light Filter ASUS BE229
Standard Mode VGA 1920 x 1080 @ 60Hz
No change.
The higher the level, the less blue light is scattered.
When Blue Light Filter is activated,the default settings of Standard Mode
will be automatically imported. Between Level 1 to Level 3, the Brightness
function is user-configurable. Level 4 is optimized setting. It is compliance
with TUV Low Blue Light Certification. The Brightness function is not user-
configurable.
Please refer to the following to alleviate eye strains:
• Users should take some time away from the display if working for long
hours. It is advised to take short breaks (at least 5 mins) after around 1
hour of continuous working at the computer. Taking short and frequent
breaks is more effective than a single longer break.
• To minimize eye strain and dryness in your eyes, users should rest the eye
periodically by focusing on objects that are far away.
3-4 Chapter 3: OSD (On-Screen Display) menu
• Eye exercises can help to reduces eye strain. Repeat these exercises
often. If eye strain continues please consult a physician. Eye exercises: (1)
Repeating look up and down (2) Slowly roll your eyes (3) Move your eyes
diagonal.
• High energy blue light may lead to eye strain and AMD (Age-Related
Macular Degeneration). Blue light Filter to reduce 70% (max.) harmful blue
light to avoiding CVS (Computer Vision Syndrome).
Set a desired color setting from this menu.
Brightness
Contrast
Saturation
Color Temp.
Skin Tone
Color ASUS BE229
Standard Mode VGA 1920 x 1080 @ 60Hz
: The adjusting range is from 0 to 100.
: The adjusting range is from 0 to 100.
: The adjusting range is from 0 to 100.
: Contains 4 modes including Cool, Normal, Warm and User
Mode.
: contains three color modes including Reddish, Natural, and
Yellowish.
3-5ASUS BE Series LCD Monitor
Set the image related setting from this menu.
Sharpness
Trace Free
Aspect Control
VividPixel
ASCR
Position
Focus
Auto Adjust
Image ASUS BE229
Standard Mode VGA 1920 x 1080 @ 60Hz
: The adjusting range is from 0 to 100.
: Adjusts the response time of the monitor.
: Adjusts the aspect ratio to full, 4:3, 1:1 (optional) or
OverScan (optional).
4:3 is only available when input source is in 4:3 format. OverScan is only
available for the HDMI input source or some typical timings..
: Enhances the outline of the displayed picture and generates
high-quality images on screen.
: Turns on/off the ASCR (ASUS Smart Contrast Ratio) function.
: adjusts the horizontal position
(H-Position) and the vertical position (V-Position) of the image. The
adjusting range is from 0 to 100.
: reduces Horizonal-line noise
and Vertical-line noise of the image by adjusting (Phase) and (Clock)
separately. The adjusting range is from 0 to 100.
• Phase adjusts the phase of the pixel clock signal. With a wrong phase
adjustment, the screen shows horizontal disturbances.
• Clock (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the image is not proportional.
: Automatically adjusts the image to its optimized position,
clock, and phase (for VGA mode only).
3-6 Chapter 3: OSD (On-Screen Display) menu
You can adjust Volume, Mute and Source from this menu.
Volume
Mute
Source
Sound ASUS BE229
Standard Mode VGA 1920 x 1080 @ 60Hz
: the adjusting range is from 0 to 100.
: toggles the monitor sound between on and off.
: decides the monitor sound comes from which source.
In this function, you can select your desired input source.
VGA
DVI
HDMI
DisplayPort
Input Select ASUS BE229
Standard Mode VGA 1920 x 1080 @ 60Hz
DVI
HDMI
DisplayPort
Mini DisplayPort
Input Select ASUS BE27A
Standard Mode DisplayPort 2560 x 1440 @ 60Hz
3-7ASUS BE Series LCD Monitor
VGA
DVI
Input Select ASUS BE209TLB
Standard Mode VGA 1920 x 1080 @ 60Hz
Allows you to adjust the system.
Splendid Demo Mode
ECO Mode
USB Charging
OSD Setup
Language
Key Lock
Information
More
System Setup ASUS BE229
Standard Mode VGA 1920 x 1080 @ 60Hz
: Splits the screen into two for Splendid modes
comparison. (Scenery mode only)
: reduces power consumption.
:
* “On” allows the USB downstream ports to generate a 5V/500mA
output when the monitor is turned on or in standby mode.
* “Off“ allows the USB downstream ports to generate a 5V/500mA
output only when the monitor is turned on.
:
3-8 Chapter 3: OSD (On-Screen Display) menu
* “On” allows the USB downstream ports to generate a 5V/2A or
5V/900mA output when the monitor is turned on or in standby
mode. The table below shows whether the USB downstream ports
can be used to charge an external device in different situations.
Downstream port Monitor status When upstream port
connected to PC...
When upstream port
connected to PC...
port Normal Allows charging Allows charging
Standby Allows charging Allows charging
port Normal Allows charging Does not allow charging
Standby Allows charging Does not allow charging
* “Off“ allows the USB downstream ports to generate a 5V/2A or
5V/900mA output only when the monitor is turned on. The table
below shows whether the USB downstream ports can be used to
charge an external device in different situations.
Downstream port Monitor status When upstream port
connected to PC...
When upstream port
connected to PC...
port Normal Allows charging Allows charging
Standby Does not allow charging Does not allow charging
port Normal Allows charging Does not allow charging
Standby Does not allow charging Does not allow charging
:
* Adjusts the OSD timeout from 10 to 120 seconds.
* Enables or disables the DDC/CI function.
* Adjusts the OSD background from opaque to transparent.
: There are 21 languages for your selection, including English,
French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech,
Croatian, Polish, Romanian, Hungarian, Turkish, Simplied Chinese,
Traditional Chinese, Japanese, Korean, Thai, Indonesian, Persian.
: To disable all function keys. Press the second button from the
right over five seconds to cancel the key lock function.
: Enables or
disables the auto source detecting function.
: Shows the monitor information.
: Turns the power LED indicator on/off.
: turns on/ off the Human Sensor
function and adjusts its sensitivity. The effective range is from 50 to 70
cm. The default setting is Off.
* Low: Sensor distance is around 50 cm.
* Medium: Sensor distance is around 60 cm.
* High: Sensor distance is around 70 cm.
3-9ASUS BE Series LCD Monitor
• The detective range may be slightly different if user wears dark or bright
colored clothing. Set the sensitivity to High when wearing black or other
dark clothes.
• Please do not put any object too close to the Human Sensor to avoid any
interference.
: Enables or disables the power key.
: “Yes” allows you to restore the default settings.
Defines the functions for Shortcut 1 and 2 buttons.
Shortcut 1
Shortcut 2
Shortcut ASUS BE229
Standard Mode VGA 1920 x 1080 @ 60Hz
: selects a function for Shortcut 1 and 2 buttons.
When a certain function is selected or activated, your shortcut key may not
support. Available function choices for shortcut: Blue Light Filter, Splendid,
Brightness, Auto Adjust, Contrast, Color Temp., Volume.
3-10 Chapter 3: OSD (On-Screen Display) menu
3.2 Specications summary
BE229/BE239/BE249 simple base
TFT LCD
BE229QB/BE229Q/BE229QBH/BE229QH: 21.5”
(16:9, 54.6 cm) wide screen
BE239QB/BE239Q: 23” (16:9, 58.4 cm) wide screen
BE249QB/BE249Q: 23.8” (16:9, 60.5 cm) wide screen
BE229QB/BE229Q/BE229QBH/BE229QH: 1920 x
1080
BE239QB/BE239Q: 1920 x 1080
BE249QB/BE249Q: 1920 x 1080
BE229QB/BE229Q/BE229QBH/BE229QH: 0.248 mm
x 0.248 mm
BE239QB/BE239Q: 0.2652 mm x 0.2652 mm
BE249QB/BE249Q: 0.2745 mm x 0.2745 mm
250 cd/m2
1000:1
100,000,000:1 (with ASCR on)
178˚/178˚
16.7 M
< 5 ms
Yes
7 video preset modes
Yes
4 color temperatures
D-sub
DVI-D with HDCP, DisplayPort v1.2, HDMI (only for
BE229QBH/BE229QH)
Yes
Yes
2 W x 2 Stereo, RMS
Upstream x 1, Downstream x 2 (only for BE229QB/
BE239QB/BE249QB)
Upstream x 1, Downstream x 2 (only for BE229QBH)
Black
White (On)/Amber (Standby)
+20˚~ -5˚
No
No
No
Yes
AC: 100~240V
3-11ASUS BE Series LCD Monitor
BE229QB/BE229Q/BE229QBH/BE229QH: Power
On: < 21.09 W** (Typ.), Standby: < 0.5 W (Typ.),
Power Off: 0 W (Switch off)
BE239QB/BE239Q: Power On: < 22 W** (Typ.),
Standby: < 0.5 W (Typ.), Power Off: 0 W (Switch off)
BE249QB/BE249Q: Power On: < 22.97 W** (Typ.),
Standby: < 0.5 W (Typ.), Power Off: 0 W (Switch off)
0˚C~40˚C
-20˚C~+60˚C
BE229QB/BE229Q/BE229QBH/BE229QH: 514 x 383
x 195 mm (machine), 576 x 442 x 120 mm (package)
BE239QB/BE239Q: 548 x 403 x 195 mm (machine),
617 x 119 x 462 mm (package)
BE249QB/BE249Q: 562 x 406 x 195 mm (machine),
632 x 127 x 465 mm (package)
BE229QB/BE229Q/BE229QBH/BE229QH: 3.8 kg
(Net); 5.3 kg (Gross)
BE239QB/BE239Q: 4.3 kg (Net); 5.7 kg (Gross)
BE249QB/BE249Q: 4.3 kg (Net); 5.9 kg (Gross)
21 languages (English, French, German, Italian,
Spanish, Dutch, Portuguese, Russian, Czech,
Croatian, Polish, Romanian, Hungarian, Turkish,
Simplied Chinese, Traditional Chinese, Japanese,
Korean, Thai, Indonesian, Persian)
Power cord, DVI cable (optional), DisplayPort
cable, VGA cable, Audio cable, USB cable (only for
BE229QB/BE229QBH/BE239QB/BE249QB), Quick
start guide, Warranty card
UL/cUL, CB, CE, ErP, FCC, ISO9241-307, RCM,
VCCI, RoHS, Windows 7 & 8 WHQL, Energy Star®,
Flicker Free, Low blue Light, TUV-GS, TUV-Ergo, CU,
PSE, WEEE, EMC DoC, UkrSEPRO, MEPS
3-12 Chapter 3: OSD (On-Screen Display) menu
BE209/BE229/BE239/BE249/BE24A/BE24W height
adjustment base
TFT LCD
BE209QLB/BE209QL: 19.45" (16:10, 49.4 cm) wide
screen
BE229QLB/BE229QL/BE229QLBH: 21.5” (16:9, 54.6
cm) wide screen
BE239QLB/BE239QL/BE239QLBR/BE239QLBH: 23”
(16:9, 58.4 cm) wide screen
BE249QLB/BE249QL/BE249QLBH: 23.8” (16:9, 60.5
cm) wide screen
BE24AQLB/BE24AQLBH/BE24WQLB: 24” (16:10,
61.13 cm) wide screen
BE209QLB/BE209QL: 1440 x 900
BE229QLB/BE229QL/BE229QLBH: 1920 x 1080
BE239QLB/BE239QL/BE239QLBR/BE239QLBH:
1920 x 1080
BE249QLB/BE249QL/BE249QLBH: 1920 x 1080
BE24AQLB/BE24AQLBH
/BE24WQLB
: 1920 x 1200
BE209QLB/BE209QL: 0.2907 mm x 0.2915 mm
BE229QLB/BE229QL/BE229QLBH: 0.248 mm x
0.248 mm
BE239QLB/BE239QL/BE239QLBR/BE239QLBH:
0.2652 mm x 0.2652 mm
BE249QLB/BE249QL/BE249QLBH: 0.2745 mm x
0.2745 mm
BE24AQLB/BE24AQLBH
/BE24WQLB
: 0.270 mm x
0.270 mm
BE209QLB/BE209QL/BE229QLB/BE229QL/
BE229QLBH/BE239QLB/BE239QL/BE239QLBR/
BE239QLBH/BE249QLB/BE249QL/BE249QLBH/
BE24AQLB: 250 cd/m2
BE24AQLBH/BE24WQLB
: 300 cd/m2
1000:1
100,000,000:1 (with ASCR on)
178˚/178˚
16.7 M
< 5 ms
Yes
7~8 video preset modes
Yes
4 color temperatures
D-sub
DVI-D with HDCP, DisplayPort v1.2, HDMI (only for
BE229QLBH/BE239QLBH/BE249QLBH/BE24AQLBH)
Yes
Yes
2 W x 2 Stereo, RMS
3-13ASUS BE Series LCD Monitor
BE209QLB/BE229QLB/BE239QLB/BE239QLBR/
BE249QLB/BE24AQLB:
Upstream x 1, Downstream x 2
BE229QLBH/BE239QLBH/BE249QLBH/
BE24AQLBH: Upstream x 1, Downstream x 2
BE24WQLB: Upstream x 1, Downstream x 4
Black/Gray
White (On)/Amber (Standby)
+35˚~ -5˚
+90˚~ -90˚
+90˚~ -90˚
130 mm
Yes
AC: 100~240V
BE209QLB/BE209QL: Power On: < 15.74 W** (Typ.),
Standby: < 0.5 W (Typ.), Power Off: 0 W (Switch off)
BE229QLB/BE229QL/BE229QLBH: Power On: <
21.09 W** (Typ.), Standby: < 0.5 W (Typ.), Power Off:
0 W (Switch off)
BE239QLB/BE239QL/BE239QLBR/BE239QLBH:
Power On: < 22 W** (Typ.), Standby: < 0.5 W (Typ.),
Power Off: 0 W (Switch off)
BE249QLB/BE249QL/BE249QLBH: Power On: <
22.97 W** (Typ.), Standby: < 0.5 W (Typ.), Power Off:
0 W (Switch off)
BE24AQLB/BE24AQLBH: Power On: < 25.4 W**
(Typ.), Standby: < 0.5 W (Typ.), Power Off: 0 W
(Switch off)
BE24WQLB: Power On: < 13.3 W** (Typ.), Standby:
< 0.22 W (Typ.), Power Off: 0 W (Switch off)
0˚C~40˚C
-20˚C~+60˚C
3-14 Chapter 3: OSD (On-Screen Display) menu
Dimension (W x H x D) with
stand
BE209QLB/BE209QL: 459 x 477 x 211 mm (highest),
459 x 347 x 211 mm (lowest), 621 x 173 x 382 mm
(package)
BE229QLB/BE229QL/BE229QLBH: 514 x 477 x 211
mm (highest), 514 x 347 x 211 mm (lowest), 643 x
378 x 190 mm (package)
BE239QLB/BE239QL/BE239QLBR/BE239QLBH:
548 x 490 x 211 mm (highest), 548 x 360 x 211 mm
(lowest), 652 x 173 x 403 mm (package)
BE249QLB/BE249QL/BE249QLBH: 562 x 492 x 211
mm (highest), 562 x 362 x 211 mm (lowest), 660 x
180 x 420 mm (package)
BE24AQLB/BE24AQLBH: 561 x 511 x 211 mm
(highest), 561 x 381 x 211 mm (lowest), 662 x 179 x
454 mm (package)
BE24WQLB: 533 x 505 x 211 mm (highest), 533
x 375 x 211 mm (lowest), 649 x 192 x 474 mm
(package)
Weight (Esti.) BE209QLB/BE209QL: 4.8 kg (Net); 6.4 kg (Gross)
BE229QLB/BE229QL/BE229QLBH: 5.7 kg (Net); 7.2
kg (Gross)
BE239QLB/BE239QL/BE239QLBR/BE239QLBH: 5.7
kg (Net); 7.3 kg (Gross)
BE249QLB/BE249QL/BE249QLBH: 5.8 kg (Net); 7.9
kg (Gross)
BE24AQLB/BE24AQLBH: 6.2 kg (Net); 8.2 kg (Gross)
BE24WQLB: 6.1 kg (Net); 3.9 kg (without stand); 8.3
kg (Gross)
Multi-languages 21 languages (English, French, German, Italian,
Spanish, Dutch, Portuguese, Russian, Czech,
Croatian, Polish, Romanian, Hungarian, Turkish,
Simplied Chinese, Traditional Chinese, Japanese,
Korean, Thai, Indonesian, Persian)
Accessories Power cord, DVI cable (optional), HDMI cable
(optional), DisplayPort cable (optional), VGA cable
(optional), Audio cable (optional), USB cable (only
for BE209QLB/BE229QLB/BE239QLB/BE239QLBR/
BE249QLB/BE24AQLB
/BE24WQLB
), Quick start
guide, Warranty card, MiniPC Kit (optional)
Compliance and Standards UL/cUL, CB, CE, ErP, FCC, ISO9241-307, RCM,
VCCI, RoHS, Windows 7 & 8 & 10 WHQL,
Energy Star®, Flicker Free, Low blue Light, TUV-GS,
TUV-Ergo, CU, PSE, WEEE, EMC DoC, UkrSEPRO,
MEPS, BSMI, NFPA99 (BE24QLBH)
Only for BE24WQLB: CCC, CEL, PC Recycle,
J-MOSS, KC, KCC, e-Standby, TCO 8.0, ICE-3
*Specications are subject to change without notice.
**Measuring a screen brightness of 200 nits without audio/USB/Card reader connection.
3-15ASUS BE Series LCD Monitor
BE27A
TFT LCD
27” (16:9, 68.47 cm) wide screen
2560 x 1440
0.2331 mm x 0.2331 mm
350 cd/m2
1000:1
100,000,000:1 (with ASCR on)
178˚/178˚
16.7 M
< 5 ms
Yes
8 video preset modes
Yes
4 color temperatures
No
DVI-D with HDCP, DisplayPort v1.2, HDMI, mini
DisplayPort
Yes
Yes
2 W x 2 Stereo, RMS
Upstream x 1, Downstream x 4
Black
White (On)/Amber (Standby)
+35˚~ -5˚
+90˚~ -90˚
+90˚~ -90˚
150 mm
Yes
AC: 100~240V
Power On: < 20.3 W** (Typ.), Standby: < 0.5 W
(Typ.), Power Off: 0 W (Switch off)
0˚C~40˚C
-20˚C~+60˚C
615 x 372 x 51 mm
615 x 532 x 226 mm (highest),
615 x 382 x 226 mm (lowest),
735 x 216 x 464 mm (package)
7.7 kg (Net); 5 kg (Without stand); 10.8 kg (Gross)
21 languages (English, French, German, Italian,
Spanish, Dutch, Portuguese, Russian, Czech,
Croatian, Polish, Romanian, Hungarian, Turkish,
Simplied Chinese, Traditional Chinese, Japanese,
Korean, Thai, Indonesian, Persian)
3-16 Chapter 3: OSD (On-Screen Display) menu
Power cord, DVI cable (optional), HDMI cable,
DisplayPort cable (optional), DisplayPort cable (Mini-
DP to DP), Audio cable, USB cable, Quick start guide,
Warranty card
UL/cUL, FCC, ICES-3, CB, CE, ErP, WEEE, TUV-
GS, TUV-Ergo, ISO 9241-307, UkrSEPRO, CU, CCC,
CEL, BSMI, RCM, MEPS, VCCI, PSE, PC Recycle,
J-MOSS, KC, KCC, e-Standby, Energy Star®, RoHs,
Windows 7/8.1/10 WHQL, Flicker Free, Low Blue
Light, NFPA99
3-17ASUS BE Series LCD Monitor
BE209TL/BE209TLB
TFT LCD
19.45" (16:10, 49.4 cm) wide
1440 x 900
0.2907 mm x 0.2915 mm
250 cd/m2
1000:1
100,000,000:1 (with ASCR on)
178˚/178˚
16.7 M
< 5 ms
Yes
7 video preset modes
Yes
4 color temperatures
D-sub
DVI-D with HDCP
No
Yes
2 W x 2 Stereo, RMS
Upstream x 1, Downstream x 2 (only for BE209TLB)
Black
White (On)/Amber (Standby)
+33˚~ -5˚
+90˚~ -90˚
+90˚~ -90˚
130 mm
Yes
AC: 100~240V
Power On: < 15.74 W** (Typ.), Standby: < 0.5 W
(Typ.), Power Off: 0 W (Switch off)
0˚C~40˚C
-20˚C~+60˚C
459 x 477 x 211 mm (highest), 459 x 347 x 211 mm
(lowest), 621 x 173 x 382 mm (package)
4.8 kg (Net); 6.4 kg (Gross)
21 languages (English, French, German, Italian,
Spanish, Dutch, Portuguese, Russian, Czech,
Croatian, Polish, Romanian, Hungarian, Turkish,
Simplied Chinese, Traditional Chinese, Japanese,
Korean, Thai, Indonesian, Persian)
Power cord, DVI cable, VGA cable, Audio cable,
USB cable (only for BE209TLB), Quick start guide,
Warranty card
3-18 Chapter 3: OSD (On-Screen Display) menu
UL/cUL, CB, CE, ErP, FCC, ISO9241-307, RCM,
VCCI, RoHS, Windows 7 & 8 WHQL, Energy Star®,
Flicker Free, Low blue Light, TUV-GS, TUV-Ergo, CU,
PSE, WEEE, EMC DoC, UkrSEPRO, MEPS
3-19ASUS BE Series LCD Monitor
3.3 Troubleshooting (FAQ)
Power LED is not ON • Press the button to check if the monitor
is in the ON mode.
• Check if the power cord is properly
connected to the monitor and the power
outlet.
• Check if the power switch is ON.
The power LED lights amber and there is
no screen image
• Check if the monitor and the computer are
in the ON mode.
• Make sure the signal cable is properly
connected the monitor and the computer.
• Inspect the signal cable and make sure
none of the pins are bent.
• Connect the computer with another
available monitor to check if the computer
is properly working.
Screen image is too light or dark • Adjust the Contrast and Brightness
settings via OSD.
Screen image is not centered or sized
properly
• Adjust the H-Position or V-Position
settings via OSD.
Screen image bounces or a wave pattern is
present in the image
• Make sure the signal cable is properly
connected to the monitor and the
computer.
• Move electrical devices that may cause
electrical interference.
Screen image has color defects (white does
not look white)
• Inspect the signal cable and make sure
that none of the pins are bent.
• Perform All Reset via OSD.
• Adjust the R/G/B color settings or select
the Color Temperature via OSD.
Screen image is blurry or fuzzy • Adjust the Phase and Clock settings via
OSD.
No sound or sound is low • Ensure that the HDMI/DisplayPort cable is
properly connected to the monitor and the
computer.
• Adjust the volume settings of both your
monitor and HDMI/DisplayPort device.
• Ensure that the computer sound card
driver is properly installed and activated.
3-20 Chapter 3: OSD (On-Screen Display) menu
3.4 Supported operating modes
BE209
640x480 31.47(N) 59.94(N) 25.18
640x480 35.00(N) 66.66(N) 30.24
640x480 37.87(N) 72.82(N) 31.5
640x480 37.5(N) 75.00(N) 31.5
720x400 31.47(N) 70.08(P) 28.32
800x600 35.16(P) 56.25(P) 36.00
800x600 37.88(P) 60.32(P) 40.00
800x600 48.08(P) 72.12(P) 50.00
800x600 46.86(P) 75.00(P) 49.50
832X624 49.72(P/N) 74.55(P/N) 57.28
1024x768 48.36(N) 60.00(N) 65.00
1024x768 56.476(N) 70.069(N) 75.00
1024x768 60.02(N) 75.00(N) 78.75
1152x864 67.5(P/N) 75.00(P/N) 108
1280x720 45.00(P) 60.00(N) 75.25
1280x768 47.78(P) 60.00(N) 79.5
1280x800 49.7(P) 60.00(N) 83.5
1360x768 47.712(P) 59.79(P) 85.5
1366x768 47.712(P) 59.79(P) 85.5
1440x900 55.94(N) 59.89(P) 106.5
1 480p 720 x 480 31.469 60 27 480p-60Hz
2 720p60 1280 x 720 45 60 74.25 720p-60Hz
3 576p 720 x 576 31.25 50 27 576p-50Hz
4 720p50 1280 x 720 37.5 50 74.25 720p-50Hz
3-21ASUS BE Series LCD Monitor
BE229/BE239/BE249
640x480 31.47(N) 59.94(N) 25.18
640x480 35.00(N) 66.66(N) 30.24
640x480 37.87(N) 72.82(N) 31.5
640x480 37.5(N) 75.00(N) 31.5
720x400 31.47(N) 70.08(P) 28.32
800x600 35.16(P) 56.25(P) 36.00
800x600 37.88(P) 60.32(P) 40.00
800x600 48.08(P) 72.12(P) 50.00
800x600 46.86(P) 75.00(P) 49.50
832X624 49.72(P/N) 74.55(P/N) 57.28
1024x768 48.36(N) 60.00(N) 65.00
1024x768 56.476(N) 70.069(N) 75.00
1024x768 60.02(N) 75.00(N) 78.75
1152x864 67.5(P/N) 75.00(P/N) 108
1280x720 45.00(P) 60.00(N) 75.25
1280x768 47.78(P) 60.00(N) 79.5
1280x800 49.7(P) 60.00(N) 83.5
1280x960 60.00(P) 60.00(N) 108
1280x1024 63.98(P) 60.02(N) 108
1280x1024 79.98(P) 75.02(N) 135
1360x768 47.712(P) 59.79(P) 85.5
1366x768 47.712(P) 59.79(P) 85.5
1440x900 55.94(N) 59.89(P) 106.5
1600x1200 75.00(P) 60.00(P) 162
1680x1050 65.29(P) 60.00(P) 146.25
1920x1080 67.5(P) 60.00(P) 148.5
3-22 Chapter 3: OSD (On-Screen Display) menu
1 480p 720 x 480 31.469 60 27 480p-60Hz
2 720p60 1280 x 720 45 60 74.25 720p-60Hz
3 576p 720 x 576 31.25 50 27 576p-50Hz
4 720p50 1280 x 720 37.5 50 74.25 720p-50Hz
5 1080p60 1920 x 1080 67.5 60 148.5 1080p-60Hz
6 1080p50 1920 x 1080 56.25 50 148.5 1080p-50Hz
BE24AQLB
640x480 31.47(N) 59.94(N) 25.18
800x600 35.16(P) 56.25(P) 36
800x600 37.88(P) 60.32(P) 40
1024x768 48.36(N) 60.00(N) 65
1280x960 60.00(P) 60.00(N) 108
1280x1024 63.98(P) 60.02(P) 108
1366x768 47.712(P) 59.79(P) 85.5
1440x900 55.94(N) 59.89(P) 106.5
1600x1200 75.00(P) 60.00(P) 162
1680x1050 65.29(N) 60.00(P) 146.25
1920x1080 67.5(P) 60.00(P) 148.5
1920x1200
(Reduced Blanking) 74.038(P) 59.95(N) 154
1 480p 720 x 480 31.469 60 27 480p-60Hz
2 720p60 1280 x 720 45 60 74.25 720p-60Hz
3 576p 720 x 576 31.25 50 27 576p-50Hz
4 720p50 1280 x 720 37.5 50 74.25 720p-50Hz
5 1080p60 1920 x 1080 67.5 60 148.5 1080p-60Hz
6 1080p50 1920 x 1080 56.25 50 148.5 1080p-50Hz
3-23ASUS BE Series LCD Monitor
BE27A
640x480 31.47(N) 59.94(N) 25.18
640x480 35.00(N) 66.66(N) 30.24
640x480 37.87(N) 72.82(N) 31.5
640x480 37.5(N) 75.00(N) 31.5
720x400 31.47(N) 70.08(P) 28.32
800x600 35.16(P) 56.25(P) 36.00
800x600 37.88(P) 60.32(P) 40.00
800x600 46.86(P) 75.00(P) 49.50
1024x768 48.36(N) 60.00(N) 65.00
1024x768 56.476(N) 70.069(N) 75.00
1024x768 60.02(N) 75.00(N) 78.75
1152x864 67.5(P/N) 75.00(P/N) 108
1280x720 45.00(P) 60.00(N) 75.25
1280x768 47.78(P) 60.00(N) 79.5
1280x800 49.7(P) 60.00(N) 83.5
1280x960 60.00(P) 60.00(N) 108
1280x1024 63.98(P) 60.02(N) 108
1280x1024 79.98(P) 75.02(N) 135
1366x768 47.712(P) 59.79(P) 85.5
1440x900 55.94(N) 59.89(P) 106.5
1600x1200 75.00(P) 60.00(P) 162
1680x1050 65.29(P) 60.00(P) 146.25
1920x1080 67.5(P) 60.00(P) 148.5
1920x1200
(Reduced Blanking) 74.038(P) 59.95(N) 154
1920x1200 74.556(N) 59.885(P) 193.25
2048x1152
(Reduced Blanking) 70.99(P) 59.9(N) 156.75
2560x1080 66.636(P) 59.978(N) 181.25
2560x1440 88.787(P) 59.951(N) 241.5
3-24 Chapter 3: OSD (On-Screen Display) menu
1 480p 720 x 480 31.469 60 27 480p-60Hz
2 720p60 1280 x 720 45 60 74.25 720p-60Hz
3 576p 720 x 576 31.25 50 27 576p-50Hz
4 720p50 1280 x 720 37.5 50 74.25 720p-50Hz
5 1080p60 1920 x 1080 67.5 60 148.5 1080p-60Hz
6 1080p50 1920 x 1080 56.25 50 148.5 1080p-50Hz
BE24W
640x480 31.47(N) 59.94(N) 25.18
640x480 35.00(N) 66.66(N) 30.24
640x480 37.87(N) 72.82(N) 31.5
640x480 37.5(N) 75.00(N) 31.5
720x400 31.47(N) 70.08(P) 28.32
800x600 35.16(P) 56.25(P) 36
800x600 37.88(P) 60.32(P) 40
800x600 46.86(P) 75.00(P) 49.5
832X624 49.72(P/N) 74.55(P/N) 57.28
1024x768 48.36(N) 60.00(N) 65
1024x768 56.476(N) 70.069(N) 75
1024x768 60.02(N) 75.00(N) 78.75
1152x864 67.5(P/N) 75.00(P/N) 108
1280x720 45.00(P) 60.00(N) 75.25
1280x768 47.78(P) 60.00(N) 79.5
1280x800 49.7(P) 60.00(N) 83.5
1280x960 60.00(P) 60.00(N) 108
1280x1024 63.98(P) 60.02(P) 108
1280x1024 79.98(P) 75.02(P) 135
1366x768 47.712(P) 59.79(P) 85.5
1440x900 55.94(N) 59.89(P) 106.5
1600x1200 75.00(P) 60.00(P) 162
1680x1050 65.29(N) 60.00(P) 146.25
1920x1080 67.5(P) 60.00(P) 148.5
3-25ASUS BE Series LCD Monitor
"1920x1200
(Reduced
Blanking)"
74.038(P) 59.95(N) 154
480p 720 x 480 31.469 60 27
720p60 1280 x 720 45 60 74.25
576p 720 x 576 31.25 50 27
720p50 1280 x 720 37.5 50 74.25
1080p60 1920 x 1080 67.5 60 148.5
1080p50 1920 x 1080 56.25 50 148.5