Table of Contents
- Contents
- Notices
- Safety information
- Care & Cleaning
- Takeback Services
- Product information for EU energy label
- Chapter 1: Product introduction
- 1.1 Welcome!
- 1.2 Package contents
- 1.3 Monitor introduction
- Chapter 2: Setup
- 2.1 Assembling the monitor arm/base
- 2.2 Detaching the arm/base (for VESA wall mount)
- 2.3 Attaching/Removing the MiniPC Kit
- 2.4 Adjusting the monitor
- 2.5 Adjusting the webcam
- 2.6 Connecting the cables
- 2.7 Turning on the monitor
- 2.8 Setting up the monitor webcam as default setting
- 2.9 Setting up the monitor speaker as default setting
- Chapter 3: General instructions
- 3.1 OSD (On-Screen Display) menu
- 3.2 Specifications summary
- 3.3 Outline dimensions
- 3.4 Troubleshooting (FAQ)
- 3.5 Supported operating modes
ASUS BE279QSK User Manual
Displayed below is the user manual for BE279QSK by ASUS which is a product in the Computer Monitors category. This manual has pages.
Related Manuals
BE279QSK Series
LCD Monitor
User Guide
ii
First Edition
March 2021
Copyright © 2021 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless
such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM
ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN
THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the
owners’ benet, without intent to infringe.
iii
Contents
Contents ...................................................................................................... iii
Notices ......................................................................................................... iv
Safety information ..................................................................................... vii
Care & Cleaning ........................................................................................ viii
Takeback Services ...................................................................................... ix
Product information for EU energy label .................................................. ix
Chapter 1: Product introduction
1.1 Welcome! .................................................................................... 1-1
1.2 Package contents ......................................................................... 1-1
1.3 Monitor introduction .................................................................... 1-2
1.3.1 Front view ....................................................................... 1-2
1.3.2 Back view ........................................................................ 1-4
Chapter 2: Setup
2.1 Assembling the monitor arm/base ............................................. 2-1
2.2 Detaching the arm/base (for VESA wall mount) ........................ 2-2
2.3 Attaching/Removing the MiniPC Kit ........................................... 2-3
2.4 Adjusting the monitor .................................................................. 2-4
2.5 Adjusting the webcam ................................................................. 2-5
2.6 Connecting the cables ................................................................. 2-6
2.7 Turning on the monitor ................................................................ 2-7
2.8 Setting up the monitor webcam as default setting ................... 2-7
2.9 Setting up the monitor speaker as default setting .................. 2-10
Chapter 3: General instructions
3.1 OSD (On-Screen Display) menu ................................................ 3-1
3.1.1 How to recongure .......................................................... 3-1
3.1.2 OSD function introduction ............................................... 3-2
3.2 Specicationssummary .............................................................. 3-9
3.3 Outline dimensions .................................................................... 3-11
3.4 Troubleshooting (FAQ) .............................................................. 3-12
3.5 Supported operating modes ..................................................... 3-13
iv
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modications
to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
ENERGY STAR complied product
ENERGY STAR is a joint program of the U.S. Environmental
Protection Agency and the U.S. Department of Energy helping us all
save money and protect the environment through energy efcient
products and practices.
All ASUS products with the ENERGY STAR logo comply with the ENERGY
STAR standard, and the power management feature is enabled by default. The
monitor and computer are automatically set to sleep after 10 and 30 minutes of
user inactivity. To wake your computer, click the mouse or press any key on the
keyboard. Please visit http://www.energystar.gov/powermanagement for detail
information on power management and its benets to the environment. In addition,
please visit http://www.energystar.gov for detail information on the ENERGY STAR
joint program.
v
NOTE: Energy Star is NOT supported on FreeDOS and Linux-based operating
system.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
This Class B digital apparatus meets all requirements of the Canadian
Interference - Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Réglement sur le matériel brouiller du Canada.
vi
A third-party certification according to ISO 14024
Say hello
to a more sustainable product
IT products are associated with a wide range of sustainability risks
throughout their life cycle. Human rights violations are common in the
factories. Harmful substances are used both in products and their
manufacture. Products can often have a short lifespan because of poor
ergonomics, low quality and when they are not able to be repaired or
upgraded.
This product is a better choice. It meets all the criteria in TCO Certified,
the world’s most comprehensive sustainability certification for IT
products. Thank you for making a responsible product choice, that help
drive progress towards a more sustainable future!
Criteria in TCO Certified have a life-cycle perspective and balance
environmental and social responsibility. Conformity is verified by
independent and approved verifiers that specialize in IT products, social
responsibility or other sustainability issues. Verification is done both
before and after the certificate is issued, covering the entire validity
period. The process also includes ensuring that corrective actions are
implemented in all cases of factory non-conformities. And last but not
least, to make sure that the certification and independent verification is
accurate, both TCO Certified and the verifiers are reviewed regularly.
Want to know more?
Read information about TCO Certified, full criteria documents, news and
updates at tcocertified.com. On the website you’ll also find our Product
Finder, which presents a complete, searchable listing of certified
products.
Toward sustainable IT products
vii
Safety information
• Before setting up the monitor, carefully read all the documentation that came
with the package.
• To prevent re or shock hazard, never expose the monitor to rain or moisture.
• Never try to open the monitor cabinet. The dangerous high voltages inside the
monitor may result in serious physical injury.
• If the power supply is broken, do not try to x it by yourself. Contact a qualied
service technician or your retailer.
• Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
• Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or over a
radiator or heat source unless proper ventilation is provided.
• The monitor should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.
• Use the appropriate power plug which complies with your local power standard.
• Do not overload power strips and extention cords. Overloading can result in re
or electric shock.
• Avoid dust, humidity, and temperature extremes. Do not place the monitor in
any area where it may become wet. Place the monitor on a stable surface.
• Unplug the unit during a lightning storm or if it will not be used for a long period
of time. This will protect the monitor from damage due to power surges.
• Never push objects or spill liquid of any kind into the slots on the monitor
cabinet.
• To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate congured receptacles marked between
100-240V AC.
• If you encounter technical problems with the monitor, contact a qualied
service technician or your retailer.
• Adjustment of the volume control as well as the equalizer to other settings
than the center position may increase the ear-/headphones output voltage and
therefore the sound pressure level.
This symbol of the crossed out wheeled bin indicates that the product (electrical,
electronic equipment, and mercury-containing button cell battery) should not
be placed in municipal waste. Please check local regulations for disposal of
electronic products.
AEEEyönetmeliğineuygundur
A third-party certification according to ISO 14024
Say hello
to a more sustainable product
IT products are associated with a wide range of sustainability risks
throughout their life cycle. Human rights violations are common in the
factories. Harmful substances are used both in products and their
manufacture. Products can often have a short lifespan because of poor
ergonomics, low quality and when they are not able to be repaired or
upgraded.
This product is a better choice. It meets all the criteria in TCO Certified,
the world’s most comprehensive sustainability certification for IT
products. Thank you for making a responsible product choice, that help
drive progress towards a more sustainable future!
Criteria in TCO Certified have a life-cycle perspective and balance
environmental and social responsibility. Conformity is verified by
independent and approved verifiers that specialize in IT products, social
responsibility or other sustainability issues. Verification is done both
before and after the certificate is issued, covering the entire validity
period. The process also includes ensuring that corrective actions are
implemented in all cases of factory non-conformities. And last but not
least, to make sure that the certification and independent verification is
accurate, both TCO Certified and the verifiers are reviewed regularly.
Want to know more?
Read information about TCO Certified, full criteria documents, news and
updates at tcocertified.com. On the website you’ll also find our Product
Finder, which presents a complete, searchable listing of certified
products.
Toward sustainable IT products
viii
Care & Cleaning
• Before you lift or reposition your monitor, it is better to disconnect the cables
and power cord. Follow the correct lifting techniques when positioning the
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.
Do not lift the display by the stand or the cord.
• Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed
with a cloth dampened with mild cleaner.
• Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended
for use with the monitor. Never spray cleaner directly on the screen, as it may
drip inside the monitor and cause an electric shock.
The following symptoms are normal with the monitor:
• You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
• When the same image is displayed for hours, an afterimage of the previous
screen may remain after switching the image. The screen will recover slowly or
you can turn off the Power Switch for hours.
• When the screen becomes black or ashes, or cannot work anymore, contact
your dealer or service center to x it. Do not repair the screen by yourself!
Conventions used in this guide
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying
to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
ix
Wheretondmoreinformation
Refer to the following sources for additional information and for product and
software updates.
1. ASUS websites
The ASUS websites worldwide provide updated information on ASUS
hardware and software products. Refer to http://www.asus.com
2. Optional documentation
Your product package may include optional documentation that may have
been added by your dealer. These documents are not part of the standard
package.
Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest
standards for protecting our environment. We believe in providing solutions for
our customers to be able to responsibly recycle our products, batteries and other
components as well as the packaging materials.
Please go to http://csr.asus.com/english/Takeback.htm for detail recycling
information in different region.
Product information for EU energy label
x
1-1ASUS BE279QSK Series LCD Monitor
1.1 Welcome!
Thank you for purchasing the ASUS® LCD monitor!
The latest widescreen LCD monitor from ASUS provides a broader, brighter and
crystal-clear display, plus a host of features that enhance your viewing experience.
With these features, you can enjoy the convenience and delightful visual
experience that the monitor brings to you!
1.2 Package contents
Check your package for the following items:
LCD monitor
Monitor base
Quick start guide
Warranty card
Power cord
HDMI cable (optional)
DisplayPort cable (optional)
VGA cable (optional)
USB B to A cable (optional)
Audio cable (optional)
MiniPC Kit (optional)
If any of the above items is damaged or missing, contact your retailer
immediately.
1-2 Chapter 1: Product introduction
1.3 Monitor introduction
1.3.1 Front view
2
7
8 9
7
34
5
61
1. Power button/power indicator
• Turns the monitor on/off.
• The color denition of the power indicator is as the below table.
Status Description
White On
Amber Standby mode
Off Off
2. Shortcut
• Default: Input Select hotkey
• To change the hotkey function, go to the Shortcut > Shortcut menu.
3. Hook button:
• To hook or unhook Skype.
4. Microphone Mute button:
• To mute or unmute the microphone.
1-3ASUS BE279QSK Series LCD Monitor
5. Volume button:
• To display the volume bar.
• Use the 5-way button to make adjustments.
• Toggle the Key Lock function between on and off with a long push
downwards for 5 seconds.
6. 5-way button:
• To display the OSD menu when the OSD is off.
• To enact the selected OSD menu items.
• To increase/decrease values or move your selection up/down/left/
right.
7. Microphone
8. Webcam cover shutter
9. Webcam
1-4 Chapter 1: Product introduction
1.3.2 Back view
1. Power switch. Press the switch to turn on/off power.
2. AC-IN port. This port connects the power cord.
3. Audio-in port. This port connects PC audio source by the bundled audio
cable.
4. Earphone jack. This port is only available when an HDMI/DisplayPort cable
is connected.
5. DisplayPort in. This port is for connection with a DisplayPort compatible
device.
6. HDMI port. This port is for connection with an HDMI compatible device.
7. VGA port. This 15-pin port is for PC VGA connection.
8. USB upstream port. This port is for connection with a USB upstream cable.
The connection enables the built-in webcam on the monitor.
9. Kensington lock slot.
2-1ASUS BE279QSK Series LCD Monitor
2.1 Assembling the monitor arm/base
To assemble the monitor base:
1. Have the front of the monitor face down on a table.
2. Attach the base into the arm, making sure the tab on the arm ts into the
groove on the base.
3. Fix the base to the arm by fastening the bundled screw.
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
180°
1
2
Base screw size: M6 x 16.5 mm.
2-2 Chapter 2: Setup
2.2 Detaching the arm/base
(for VESA wall mount)
The detachable arm/base of this monitor is specially designed for VESA wall mount.
To detach the arm/base:
1. Have the front of the monitor face down on a table (Figure 1).
2. Press the release button, and then detach the arm/base from the monitor
(Figure 2).
1
2
(Figure 1) (Figure 2)
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
• The VESA wall mount kit (100 x 100 mm) is purchased separately.
• Use only the UL Listed Wall Mount Bracket with minimum weight/load
22.7kg (Screw size: M4 x 10 mm)
2-3ASUS BE279QSK Series LCD Monitor
2.3 Attaching/Removing the MiniPC Kit
Attaching the MiniPC Kit
1
2
2
1
2
1
Removing the MiniPC Kit
1
1
2
2
2
1
2-4 Chapter 2: Setup
2.4 Adjusting the monitor
• For optimal viewing, we recommend that you look at the full face of the
monitor, then adjust the monitor to the angle that is most comfortable for you.
• Hold the stand to prevent the monitor from falling when you change its angle.
• You can adjust the monitor’s angle from +35˚ to -5˚and it allows 180˚ swivel
adjustment (by removing the stop screw) from either left or right. You can also
adjust the monitor’s height within +/- 150 mm.
150mm
180° 0° 180°
-5° ~ +35°
(Swivel) (Height adjustment)
(Tilt)
Pivoting the monitor
1. Lift the monitor to the highest position.
2. Tilt the monitor to its maximum angle.
3. Pivot the monitor clockwise/counterclockwise to the angle you need.
-5° ~ +35°
0°
90°
0°
- 90°
It is normal that the monitor slightly shakes while you adjust the viewing angle.
2-5ASUS BE279QSK Series LCD Monitor
2.5 Adjusting the webcam
• You can adjust the webcam’s angle from +10˚ to -10˚.
• The webcam allows 180˚ swivel adjustment clockwise and 135˚ swivel
adjustment counterclockwise.
+180° -135°
-10° ~ +10°
• Slide the webcam cover shutter on the top to open or close the lens.
Remove the protection lm on the front of the webcam before using.
2-6 Chapter 2: Setup
2.6 Connecting the cables
Connect the cables as the following instructions:
• To connect the power cord: Connect one end of the power cord securely to
the monitor’s AC input port, the other end to a power outlet.
• To connect the VGA/DisplayPort/HDMI cable:
a. Plug one end of the VGA/DisplayPort/HDMI cable to the monitor’s VGA/
DisplayPort/HDMI jack.
b. Connect the other end of the VGA/DisplayPort/HDMI cable to your
computer's VGA/DisplayPort/HDMI jack.
c. Tighten the two screws to secure the VGA connector.
• To connect the audio cable: connect one end of the audio cable to the
monitor’s Audio-in port, the other end to the computer’s audio-out port.
• To use the earphone: connect the end with plug type to the monitor’s
earphone jack when an HDMI/DisplayPort signal is fed.
• To use the USB 2.0 port: Take the supplied USB 2.0 cable, and plug
the smaller end (type B) of the USB upstream cable to the monitor’s USB
upstream port, and the larger end (type A) to your computer’s USB 2.0 port.
Make sure your computer is installed with the lastest Windows 7/Windows 10
operating system. That will enable the built-in webcam on the monitor to work.
2-7ASUS BE279QSK Series LCD Monitor
USB
When these cables are connected, you can choose the desired signal from the
Input Select item in the OSD menu.
2.7 Turning on the monitor
Press the power button . See page 1-2 for the location of the power button. The
power indicator lights up in white to show that the monitor is ON.
2.8 Setting up the monitor webcam as
default setting
When using a notebook with built-in webcam to connect this monitor, in
the device manager interface, you can find the notebook built-in webcam
and the monitor webcam. Normally, they are in enable status, and the
default setting is using notebook built-in webcam.
If you want to set up the monitor webcam as default setting, you need
disable the notebook built-in webcam. To identify the notebook built-in
webcam and disable it, please follow below instructions:
2-8 Chapter 2: Setup
Right-click USB2.0 HD UVC WebCam, and click Properties to open the
USB2.0 HD UVC WebCam.
Click Details > Property and select Hardware Ids.
2-9ASUS BE279QSK Series LCD Monitor
For BE/C6 webcam series, the monitor webcam hardware ids will show as below:
Right click the notebook webcam which has different hardware ids of the BE/C6
webcam series monitor webcam, and then click Disable.
The following message is displayed:
Click Yes. The notebook webcam is now disabled and the monitor webcam will be
used as the default setting. Restart the notebook.
2-10 Chapter 2: Setup
2.9 Setting up the monitor speaker as
default setting
When your computer connects multiple speakers, if you want to set up the
monitor speaker as default setting, please follow below instructions:
Right-click Volume in the Windows task bar notification area.
Click Open Sound settings enter to Sound setting interface.
Enter Sound setting interface then select Sound Control Panel.
2-11ASUS BE279QSK Series LCD Monitor
If the USB cable and the HDMI or DP cable are connected from monitor to the
computer,
Click ASUS BE/C6 webcam series Set Default, the monitor speaker will be used
as the default setting.
Click OK to exit the Sound setting.
Sound setting set the BE/C6 webcam series as default.
2-12 Chapter 2: Setup
If the Only HDMI or DP cable are connected from monitor to the computer, check
ASUS BE/C6 Monitor Set Default, the monitor speaker will be used as the default
setting.
Sound setting set the ASUS BE/C6 as default.
3-1ASUS BE279QSK Series LCD Monitor
3.1 OSD (On-Screen Display) menu
3.1.1 How to reconfigure
ASUS BE279QSK
Standard Mode DisplayPort 1920 x 1080 @ 60Hz
Splendid
Scenery Mode
Standard Mode
Theater Mode
Game Mode
Night View Mode
sRGB Mode
Reading Mode
Darkroom Mode
1. Press the 5-way button to activate the OSD menu.
2. Move the 5-way button up/down/left/right to navigate through the
functions. Highlight the desired function and press the 5-way button to
activate it. If the function selected has a sub-menu, move the 5-waybutton
up/down to navigate through the sub-menu functions. Highlight the desired
sub-menu function and press the 5-way button or move the 5-way
button to activate it.
3. Move the 5-way button up/down to change the settings of the selected
function.
4. To exit and save the OSD menu, press the button or move the 5-way
left repeatedly until the OSD menu disappears. To adjust other functions,
repeat steps 1-3.
3-2 Chapter 3: OSD (On-Screen Display) menu
3.1.2 OSD function introduction
1. Splendid
This function contains 7~8 sub-functions you can select for your preference.
Each mode has the Reset selection, allowing you to maintain your setting or
return to the preset mode.
ASUS BE279QSK
Standard Mode DisplayPort 1920 x 1080 @ 60Hz
Splendid
Scenery Mode
Standard Mode
Theater Mode
Game Mode
Night View Mode
sRGB Mode
Reading Mode
Darkroom Mode
• Scenery Mode: Best choice for scenery photo display with Splendid
Video Enhancement.
• Standard Mode: Best choice for document editing with Splendid Video
Enhancement.
Standard Mode meets Energy Star® requirements.
• Theater Mode: Best choice for movies with Splendid Video
Enhancement.
• Game Mode: Best choice for games playing with Splendid Video
Enhancement.
• Night View Mode: Best choice for dark-scene games or movies with
Splendid Video Enhancement.
• sRGB Mode: best choice for viewing photos and graphics from PCs.
• Reading Mode: This is the best choice for book reading.
• Darkroom Mode: This is the best choice for a weak ambient light
environment.
• In the Standard mode, the following function(s) are not user-configurable:
Saturation, Skin Tone, Sharpness, ASCR.
• In the sRGB mode, the following function(s) are not user-configurable:
Brightness, Contrast, Saturation, Color Temp., Skin Tone, Sharpness,
ASCR.
• In the Reading mode, the following function(s) are not user-congurable:
Contrast, Saturation, Color Temp., Skin Tone, ASCR.
3-3ASUS BE279QSK Series LCD Monitor
2. Blue Light Filter
In this function, you can adjust the blue light filter level.
ASUS BE279QSK
Standard Mode DisplayPort 1920 x 1080 @ 60Hz
Level 0
Level 1
Level 2
Level 3
Level 4
Blue Light Filter
• Level 0: No change.
• Level 1~4: The higher the level, the less blue light is scattered.
When Blue Light Filter is activated,the default settings of Standard Mode
will be automatically imported. Between Level 1 to Level 3, the Brightness
function is user-configurable. Level 4 is optimized setting. It is compliance
with TUV Low Blue Light Certification. The Brightness function is not user-
configurable.
Please refer to the following to alleviate eye strains:
• Users should take some time away from the display if working for long
hours. It is advised to take short breaks (at least 5 mins) after around 1
hour of continuous working at the computer. Taking short and frequent
breaks is more effective than a single longer break.
• To minimize eye strain and dryness in your eyes, users should rest the eye
periodically by focusing on objects that are far away.
• Eye exercises can help to reduces eye strain. Repeat these exercises
often. If eye strain continues please consult a physician. Eye exercises: (1)
Repeating look up and down (2) Slowly roll your eyes (3) Move your eyes
diagonal.
• High energy blue light may lead to eye strain and AMD (Age-Related
Macular Degeneration). Blue light Filter to reduce 70% (max.) harmful blue
light to avoiding CVS (Computer Vision Syndrome).
3-4 Chapter 3: OSD (On-Screen Display) menu
3. Color
Set a desired color setting from this menu.
ASUS BE279QSK
Standard Mode DisplayPort 1920 x 1080 @ 60Hz
Brightness
Contrast
Saturation
Color Temp.
Skin Tone
Color
• Brightness: The adjusting range is from 0 to 100.
• Contrast: The adjusting range is from 0 to 100.
• Saturation: The adjusting range is from 0 to 100.
• Color Temp.: Contains 4 modes including Cool, Normal, Warm and User
Mode.
• Skin Tone: contains three color modes including Reddish, Natural, and
Yellowish.
4. Image
Set the image related setting from this menu.
ASUS BE279QSK
Standard Mode DisplayPort 1920 x 1080 @ 60Hz
Sharpness
Trace Free
Aspect Control
VividPixel
ASCR
Position
Focus
Auto Adjust
Image
• Sharpness: The adjusting range is from 0 to 100.
• Trace Free: Adjusts the response time of the monitor.
• Aspect Control: Adjusts the aspect ratio to full, 4:3, 1:1 (optional) or
OverScan (optional).
4:3 is only available when input source is in 4:3 format. OverScan is only
available for the HDMI input source.
3-5ASUS BE279QSK Series LCD Monitor
• VividPixel: Enhances the outline of the displayed picture and generates
high-quality images on screen.
• ASCR: Turns on/off the ASCR (ASUS Smart Contrast Ratio) function.
• Position (Only available for VGA input): adjusts the horizontal position
(H-Position) and the vertical position (V-Position) of the image. The
adjusting range is from 0 to 100.
• Focus (Only available for VGA input): reduces Horizonal-line noise
and Vertical-line noise of the image by adjusting (Phase) and (Clock)
separately. The adjusting range is from 0 to 100.
• Phase adjusts the phase of the pixel clock signal. With a wrong phase
adjustment, the screen shows horizontal disturbances.
• Clock (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the image is not proportional.
• Auto Adjust.: Automatically adjusts the image to its optimized position,
clock, and phase (for VGA mode only).
5. Sound
You can adjust Volume, Mute and Source from this menu.
Volume
Mute
Source
Sound ASUS BE279QSK
Standard Mode DisplayPort 1920 x 1080 @ 60Hz
• Volume: the adjusting range is from 0 to 100.
• Mute: toggles the monitor sound between on and off.
• Source: decides the monitor sound comes from which source.
3-6 Chapter 3: OSD (On-Screen Display) menu
6. Input Select
In this function, you can select your desired input source.
ASUS BE279QSK
Standard Mode DisplayPort 1920 x 1080 @ 60Hz
VGA
HDMI
DisplayPort
Input Select
7. System Setup
Allows you to adjust the system.
Splendid Demo Mode
QuickFit
ECO Mode
Webcam
OSD Setup
Language
Key Lock
More
System Setup ASUS BE279QSK
Standard Mode DisplayPort 1920 x 1080 @ 60Hz
• Splendid Demo Mode: Splits the screen into two for Splendid modes
comparison. (Scenery mode only)
• QuickFit: You can have a preview of the document or photo layout
directly on screen without printing test copies.
* Grid pattern: This facilitates designers and users to organize content
and layout on one page and achieve a consistent look and feel.
Alignment Grid 1 Alignment Grid 2
3-7ASUS BE279QSK Series LCD Monitor
* Paper size: You can view the documents in real size on the screen.
A4 B5
Letter
* Photo: The various real photo sizes displayed in the QuickFit function
provides photographers and other users to accurately view and edit
their photos in real size on the screen.
3x5 2x2
4x6 5x7
8x10
• ECO Mode: reduces power consumption.
• Webcam: To enable or disable the webcam function.
• OSD Setup:
* Adjusts the OSD timeout from 10 to 120 seconds.
* Enables or disables the DDC/CI function.
* Adjusts the OSD background from opaque to transparent.
• Language: There are 21 languages for your selection, including English,
French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech,
Croatian, Polish, Romanian, Hungarian, Turkish, Simplied Chinese,
Traditional Chinese, Japanese, Korean, Thai, Indonesian, Persian.
• Key Lock: To disable all function keys. Press the Volume button for
over five seconds to cancel the key lock function.
• Information: Shows the monitor information.
• Power Indicator: Turns the power LED indicator on/off.
• Power Key Lock: Enables or disables the power key.
3-8 Chapter 3: OSD (On-Screen Display) menu
• Auto Source Detection: Enables or disables the auto source detecting
function.
• All Reset: “Yes” allows you to restore the default settings.
8. Shortcut
Defines the function for the Shortcut button.
ASUS BE279QSK
Standard Mode DisplayPort 1920 x 1080 @ 60Hz
Shortcut
Shortcut
• Shortcut : Selects a function for the Shortcut button.
When a certain function is selected or activated, your shortcut key may not
support. Available function choices for shortcut: Blue Light Filter, Splendid,
Brightness, Auto Adjust, Contrast, Color Temp., Input Select.
3-9ASUS BE279QSK Series LCD Monitor
3.2 Specicationssummary
Panel Type TFT LCD
Panel size
27” (16:9, 68.6 cm) wide screen
Max. Resolution 1920 x 1080
Pixel pitch 0.3114 mm x 0.3114 mm
Brightness (Typ.) 250 cd/m2
Contrast Ratio (Typ.) 1000:1
Contrast Ratio (Max.) 100,000,000:1 (with ASCR on)
Viewing angle (H/V) CR>10 178˚/178˚
Display colors 16.7 M
Response time < 5 ms
Splendid Video Enhancement Yes
Splendid selection 8 video preset modes
Auto adjustment Yes
Color temperature selection 4 color temperatures
Analog input D-sub
Digital input
DisplayPort v1.2, HDMI v1.4
Digital Output No
Earphone jack Yes
Audio input Yes
Speaker (Built-in) 2 W x 2 Stereo, RMS
USB 2.0 port Upstream x 1
Colors Black
Power LED White (On)/Amber (Standby)
Tilt +35˚~ -5˚
Pivot +90˚~ -90˚
Swivel +180˚~ -180˚
Height Adjustment 150 mm
Kensington lock Yes
AC input voltage AC: 100~240V
Power consumption Power On: < 30 W** (Typ.), Standby: < 0.5 W (Typ.),
Power Off: 0 W (Switch off)
Temperature (Operating) 0˚C~40˚C
Temperature (Non-operating) -20˚C~+60˚C
Dimension (W x H x D) without
stand
611 x 396 x 56 mm
Dimension (W x H x D) with
stand
611 x 548 x 266 mm (highest),
611 x 398 x 266 mm (lowest),
712 x 468 x 228 mm (package)
Weight (Esti.) 6.8 kg (Net); 4.8 kg (Without stand); 9.3 kg (Gross)
Multi-languages 21 languages (English, French, German, Italian,
Spanish, Dutch, Portuguese, Russian, Czech,
Croatian, Polish, Romanian, Hungarian, Turkish,
Simplied Chinese, Traditional Chinese, Japanese,
Korean, Thai, Indonesian, Persian)
3-10 Chapter 3: OSD (On-Screen Display) menu
Accessories Quick start guide, warranty card, power cord, HDMI
cable (optional), DisplayPort cable (optional), VGA
cable (optional), USB B to A cable (optional), audio
cable (optional), MiniPC Kit (optional)
Compliance and Standards
cTUVus, CB, CE, ErP, EU Energy label, FCC, ICES-
003, CCC, CEL, ISO 9241-307, BSMI, CU, C-Tick,
MEPS, VCCI, PSE, J-MOSS, KC, KCC, e-Standby,
RoHS, Windows 7 / 10 WHQL, Energy Star 8.0,
EPEAT Bronze, TCO 8.0, Flicker Free, Low Blue Light,
WEEE, NFPA99
*Specications are subject to change without notice.
**Measuring a screen brightness of 200 nits without audio/USB/Card reader connection.
3-11ASUS BE279QSK Series LCD Monitor
3.3 Outline dimensions
134.09
146.70
206.81
219.42
121.00 [4.76]
100.00 [3.94]
M3.5-Depth 5mm
Swivel：+/-180°
135°
180°
Webcam/Swivel：
Clockwise 180°
Counterclockwise 135°
Webcam/Tilt：-10°~10°
Wall mount Keep out area
100.00 [3.94]
121.00 [4.76]
90°
90°
10°
10°
Tilt：-5°~35°
Pivot：±90°
ASUS C6279QSK/BE279QSK Outline
Dimension
*Unit：mm（inch）
5°
35°
610.70 [24.04]
597.89 [23.54] Active Area
65.00 [2.56]
20.00 [0.79]
6.39 [0.25]
6.41 [0.25]
27.74 [1.09]
6.41 [0.25]
370.45 [14.58]
336.31 [13.24] Active Area
298.94 [11.77]
168.16 [6.62]
226.31 [8.91]
262.71 [10.34]
150.00 [5.91]
364.41 [14.35]
348.29 [13.71]
198.29 [7.81]
55.57 [2.19]
73.99 [2.91]
50.10 [1.97]
18.40 [0.72]
547.98 [21.57]
395.78 [15.58]
152.20 [5.99]
37.10 [1.46]
3-12 Chapter 3: OSD (On-Screen Display) menu
3.4 Troubleshooting (FAQ)
Problem Possible Solution
Power LED is not ON • Press the button to check if the monitor
is in the ON mode.
• Check if the power cord is properly
connected to the monitor and the power
outlet.
• Check if the power switch is ON.
The power LED lights amber and there is
no screen image
• Check if the monitor and the computer are
in the ON mode.
• Make sure the signal cable is properly
connected the monitor and the computer.
• Inspect the signal cable and make sure
none of the pins are bent.
• Connect the computer with another
available monitor to check if the computer
is properly working.
Screen image is too light or dark • Adjust the Contrast and Brightness
settings via OSD.
Screen image is not centered or sized
properly
• Adjust the H-Position or V-Position
settings via OSD.
Screen image bounces or a wave pattern is
present in the image
• Make sure the signal cable is properly
connected to the monitor and the
computer.
• Move electrical devices that may cause
electrical interference.
Screen image has color defects (white does
not look white)
• Inspect the signal cable and make sure
that none of the pins are bent.
• Perform All Reset via OSD.
• Adjust the R/G/B color settings or select
the Color Temperature via OSD.
Screen image is blurry or fuzzy • Adjust the Phase and Clock settings via
OSD.
No sound or sound is low • Ensure that the HDMI/DisplayPort cable is
properly connected to the monitor and the
computer.
• Adjust the volume settings of both your
monitor and HDMI/DisplayPort device.
• Ensure that the computer sound card
driver is properly installed and activated.
3-13ASUS BE279QSK Series LCD Monitor
3.5 Supported operating modes
Resolution
Frequency
Horizontal
Frequency (KHz)
Vertical Frequency
(Hz)
Pixel (MHz)
640x480 31.47(N) 59.94(N) 25.18
640x480 35.00(N) 66.66(N) 30.24
640x480 37.87(N) 72.82(N) 31.5
640x480 37.5(N) 75.00(N) 31.5
720x400 31.47(N) 70.08(P) 28.32
800x600 35.16(P) 56.25(P) 36.00
800x600 37.88(P) 60.32(P) 40.00
800x600 48.08(P) 72.12(P) 50.00
800x600 46.86(P) 75.00(P) 49.50
832X624 49.72(P/N) 74.55(P/N) 57.28
1024x768 48.36(N) 60.00(N) 65.00
1024x768 56.476(N) 70.069(N) 75.00
1024x768 60.02(N) 75.00(N) 78.75
1152x864 67.5(P/N) 75.00(P/N) 108
1280x720 45.00(P) 60.00(N) 75.25
1280x768 47.78(P) 60.00(N) 79.5
1280x800 49.7(P) 60.00(N) 83.5
1280x960 60.00(P) 60.00(N) 108
1280x1024 63.98(P) 60.02(N) 108
1280x1024 79.98(P) 75.02(N) 135
1360x768 47.712(P) 59.79(P) 85.5
1366x768 47.712(P) 59.79(P) 85.5
1440x900 55.94(N) 59.89(P) 106.5
1600x1200 75.00(P) 60.00(P) 162
1680x1050 65.29(P) 60.00(P) 146.25
1920x1080 67.5(P) 60.00(P) 148.5
* “P” / “N” stands for “Positive” / “Negative” polarity of incoming H-sync/V-sync (input timing).
3-14 Chapter 3: OSD (On-Screen Display) menu
When the monitor is operating in the video mode (ie, not displaying data), the following high
denition modes shall be supported in addition to standard denition video.
Preset Timing
Name
Pixel Format Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Rate
(MHz)
OSD
Display
1480p 720 x 480 31.469 60 27 480p-60Hz
2 720p60 1280 x 720 45 60 74.25 720p-60Hz
3 576p 720 x 576 31.25 50 27 576p-50Hz
4 720p50 1280 x 720 37.5 50 74.25 720p-50Hz
5 1080p60 1920 x 1080 67.5 60 148.5 1080p-60Hz
6 1080p50 1920 x 1080 56.25 50 148.5 1080p-50Hz