Table of Contents
ASUS G10DK-75700G025W User Manual
Displayed below is the user manual for G10DK-75700G025W by ASUS which is a product in the PCs/Workstations category. This manual has pages.
Related Manuals
Desktop PC
G10DK
User Guide
2
E19413
Revised Edition v3
October 2021
Copyright © 2021 ASUSTeK Computer Inc. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except
documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK
Computer Inc. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless such
repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the product is
defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE
LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR
LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF
ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS
MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE
ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A
COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES
THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights
of their respective companies, and are used only for identication or explanation and to the owners’ benet,
without intent to infringe.
SERVICE AND SUPPORT
Visit our multi-language website at https://www.asus.com/support/.
3
Contents
Notices ................................................................................................................................................ 4
Safety information ...........................................................................................................................9
Conventions used in this guide.................................................................................................11
Where to nd more information ...............................................................................................11
Package contents ...........................................................................................................................12
Chapter 1 Getting started
Welcome! ........................................................................................................................................... 13
Getting to know your computer ...............................................................................................13
Setting up your computer...........................................................................................................17
Turning your computer ON ........................................................................................................19
Chapter 2 Connecting devices to your computer
Connecting a USB storage device ............................................................................................21
Connecting microphone and speakers ..................................................................................22
Connecting multiple external displays ..................................................................................25
Connecting an HDTV ....................................................................................................................26
Chapter 3 Using your computer
Proper posture when using your Desktop PC ...................................................................... 27
Chapter 4 Connecting to the Internet
Wired connection ........................................................................................................................... 29
Wi-Fi connection (on selected models only) ........................................................................33
Chapter 5 Troubleshooting
Troubleshooting .............................................................................................................................35
Appendix Working with Windows®
Starting for the rst time .............................................................................................................43
Start menu ........................................................................................................................................43
Windows® apps ...............................................................................................................................44
Connecting to wireless networks .............................................................................................44
Connecting to wired networks ..................................................................................................45
Turning your computer o .........................................................................................................45
Putting your computer to sleep ................................................................................................45
4
Notices
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards for
protecting our environment. We believe in providing solutions for you to be able to responsibly
recycle our products, batteries, other components, as well as the packaging materials. Please go to
http://csr.asus.com/english/Takeback.htm for the detailed recycling information in dierent regions.
REACH
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals)
regulatory framework, we published the chemical substances in our products at ASUS REACH
website at http://csr.asus.com/english/REACH.htm
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
• This device may not cause harmful interference; and
• This device must accept any interference received including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required to
assure compliance with FCC regulations. Changes or modications to this unit not expressly
approved by the party responsible for compliance could void the user’s authority to operate this
equipment.
Lithium Battery Warning
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type recommended by the manufacturer. Dispose of used batteries according
to the manufacturer’s instructions.
5
Compliance Statement of Innovation, Science and Economic Development
Canada (ISED)
This device complies with Innovation, Science, and Economic Development Canada licence exempt
RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device:
Operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems.
CAN ICES-003(B)/NMB-003(B)
Déclaration de conformité de Innovation, Sciences et Développement
économique Canada (ISED)
Le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique
Canadaapplicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil
doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
La bande 5150 – 5250 MHz est réservée uniquement pour une utilisation à l’intérieur an de réduire
les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes
canaux.
CAN ICES-003(B)/NMB-003(B)
IC: Canadian Compliance Statement
Complies with the Canadian ICES-003 Class B specications. This device complies with RSS 210
of Industry Canada. This Class B device meets all the requirements of the Canadian interference-
causing equipment regulations.
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject
to the following two conditions: this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Déclaration de conformité d’Industrie Canada
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Cet appareil
numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du
Canada.
Le présent appareil est conforme aux normes CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. Son utilisation est sujette aux deux conditions suivantes : (1) cet appareil
ne doit pas créer d’interférences et (2) cet appareil doit tolérer tout type d’interférences, y compris
celles susceptibles de provoquer un fonctionnement non souhaité de l’appareil.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
This class B digital apparatus complies with Canadian ICES-003.
Avertissement relatif aux batteries Lithium
ATTENTION ! Danger d’explosion si la batterie n’est pas correctement remplacée.
Remplacer uniquement avec une batterie de type semblable ou équivalent, recommandée
par le fabricant. Jeter les batteries usagées conformément aux instructions du fabricant.
6
KC: Korea Warning Statement
VCCI: Japan Compliance Statement
VCCI Class B Statement
This is a Class B product based on the standard of the VCCI Council. If this is used near a radio or
television receiver, it may cause radio interference. Install and use equipment according to the
instruction manual.
Equipment registered based on the conrmation measurement at the user
installation site.
This is a product for which interference was measured at the present installation site and conrmed
to comply with the standard of Voluntary Control Council for Interference by Information
Technology Equipment (VCCI). Before using the equipment at any location other than the present
installation site, the member shall measure interference for conrmation and register the result to
VCCI.
India E-Waste (Management) Rules 2016
This product complies with the “India E-Waste (Management) Rules, 2016” and prohibits use of lead,
mercury, hexavalent chromium, polybrominated biphenyls (PBBs) and polybrominated diphenyl
ethers (PBDEs) in concentrations exceeding 0.1% by weight in homogenous materials and 0.01 %
by weight in homogenous materials for cadmium, except for the exemptions listed in Schedule II of
the Rule.
Déclaration du Département Canadien des Communications
Cet appareil numérique ne dépasse pas les limites de classe B en terme d’émissions de
nuisances sonores, par radio, par des appareils numériques, et ce conformément aux régulations
d’interférence par radio établies par le département canadien des communications.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
7
NCC: Taiwan Wireless Statement
低功率射頻器材技術規範
「取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大
功率或變更原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經
發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電信管
理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性
電機設備之干擾。」 應避免影響附近雷達系統之操作。
Japan RF Equipment Statement
KC (RF Equipment)
RF Equipment Notices
CE: European Community Compliance Statement
The equipment complies with the RF Exposure Requirement 1999/519/EC, Council
Recommendation of 12 July 1999 on the limitation of exposure of the general public to
electromagnetic elds (0–300 GHz).
Wireless Radio Use
This device is restricted to indoor use when operating in the 5.15 to 5.25 GHz frequency band. For
the standard EN 300 440, the device operating in 802.11a/n/ac mode is considered as a receiver
category 2.
Exposure to Radio Frequency Energy
The radiated output power of the Wi-Fi technology is below the FCC radio frequency exposure
limits. Nevertheless, it is advised to use the wireless equipment in such a manner that the potential
for human contact during normal operation is minimized.
FCC Bluetooth Wireless Compliance
The antenna used with this transmitter must not be colocated or operated in conjunction with any
other antenna or transmitter subject to the conditions of the FCC Grant.
Bluetooth Industry Canada Statement
This Class B device meets all requirements of the Canadian interference-causing equipment
regulations.
Cet appareil numérique de la Class B respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
Simplied EU Declaration of Conformity
ASUSTek Computer Inc. hereby declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU. Full text of EU declaration of
conformity is available at https://www.asus.com/support/.
The Wi-Fi operating in the band 5150-5350MHz shall be restricted to indoor use for countries listed
in the table below:
8
Optical Drive Safety Information
Laser Safety Information
CD-ROM Drive Safety Warning
CLASS 1 LASER PRODUCT
WARNING! To prevent exposure to the optical drive’s laser, do not attempt to disassemble
or repair the optical drive by yourself. For your safety, contact a professional technician for
assistance.
Service warning label
WARNING! INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM OR VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS.
CDRH Regulations
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug
Administration implemented regulations for laser products on August 2, 1976. These
regulations apply to laser products manufactured from August 1, 1976. Compliance is
mandatory for products marketed in the United States.
WARNING! Use of controls or adjustments or performance of procedures other than those
specied herein or in the laser product installation guide may result in hazardous radiation
exposure.
AT BE BG CZ DK EE FR
DE IS IE IT EL ES CY
LV LI LT LU HU MT NL
NO PL PT RO SI SK TR
FI SE CH HR UK(NI)
Simplied UKCA Declaration of Conformity
ASUSTek Computer Inc. hereby declares that this device is in compliance with the essential
requirements and other relevant provisions of The Radio Equipment Regulations 2017 (S.I.
2017/1206). Full text of UKCA declaration of conformity is available at
https://www.asus.com/support/.
The Wi-Fi operating in the band 5150-5350MHz shall be restricted to indoor use for the country
listed below:
UK
9
Safety information
Disconnect the AC power and peripherals before cleaning. Wipe the Desktop PC using a clean
cellulose sponge or chamois cloth dampened with solution of nonabrasive detergent and a few
drops of warm water then remove any extra moisture with a dry cloth.
• DO NOT place on uneven or unstable work surfaces. Seek servicing if the casing has been
damaged.
• DO NOT expose to dirty or dusty environments. DO NOT operate during a gas leak.
• DO NOT place or drop objects on top and do not shove any foreign objects into the Desktop
PC.
• DO NOT expose to strong magnetic or electrical elds.
• DO NOT expose to or use near liquids, rain, or moisture. DO NOT use the modem during
electrical storms.
• Battery safety warning: DO NOT throw the battery in re. DO NOT short circuit the contacts.
DO NOT disassemble the battery.
• Use this product in environments with ambient temperatures between 0°C (32°F) and 35°C
(95°F).
• DO NOT cover the vents on the Desktop PC to prevent the system from getting overheated.
• DO NOT use damaged power cords, accessories, or other peripherals.
•
To prevent electrical shock hazard, disconnect the power cable from the electrical outlet
before relocating the system.
•
Seek professional assistance before using an adapter or extension cord. These devices could
interrupt the grounding circuit.
•
Ensure that your power supply is set to the correct voltage in your area. If you are not sure
about the voltage of the electrical outlet you are using, contact your local power company.
•
If the power supply is broken, do not try to x it by yourself. Contact a qualied service
technician or your retailer.
Hazardous moving parts. Desktop should be completely shutdown before servicing product.
Replacing fan components should only be attempted by qualied service personnel.
Hazardous Moving Parts Warning
WARNING: Keep ngers and other body parts away from any moving parts.
Coating notice
IMPORTANT! To provide electrical insulation and maintain electrical safety, a coating is
applied to insulate the device except on the areas where the I/O ports are located.
10
FCC COMPLIANCE INFORMATION
Per FCC Part 2 Section 2.1077
Responsible Party:
Asus Computer International
Address: 48720 Kato Rd, Fremont
,
CA 94538.
Phone/Fax No: (510)739-3777/(510)608-4555
hereby declares that the product
Product Name :
DESKTOP PC
Model Number :
G10DK
compliance statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Ver. 180620
11
Conventions used in this guide
To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.
Where to nd more information
Refer to the following sources for additional information and for product and software updates.
ASUS websites
The ASUS website provides updated information on ASUS hardware and software products.
Refer to the ASUS website www.asus.com.
ASUS Local Technical Support
Visit ASUS website at https://www.asus.com/support/contact for the contact information of
local Technical Support Engineer.
DANGER/WARNING:: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying to
complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
NOTE: Tips and additional information to help you complete a task.
12
Package contents
Desktop PC
G10DK
Keyboard x1 Mouse x1
Installation Guide
Power cord x1 Installation Guide x1 Warranty Card x1
• If any of the above items is damaged or missing, contact your retailer.
• The illustrated items above are for reference only. Actual product specications may vary with
dierent models.
Welcome!
Thank you for purchasing the ASUS Desktop PC!
The ASUS Desktop PC provides cutting-edge performance, uncompromised reliability, and user-
centric utilities. All these values are encapsulated in a stunningly futuristic and stylish system
casing.
Read the ASUS Warranty Card before setting up your ASUS Desktop PC.
Getting to know your computer
Illustrations are for reference only. The ports, their locations and the chassis color vary with
dierent models.
IMPORTANT! Do not use this Desktop PC for cryptocurrency mining (consuming a vast amount
of electricity and time to gain convertible virtual currency) and/or related activities.
ASUS G10DK 13
Chapter 1
Getting started
Front Top
Power button. Press this button to turn on your computer.
Headset port. This port connects to a headset, headphone, microphone, or speaker.
USB 3.2 Gen 1 ports. These ports connect to USB 3.2 Gen 1 devices such as a mouse,
printer, scanner, camera, PDA, and others.
USB 3.2 Gen 1 devices can only be used for data storage.
14 Chapter 1: Getting started
ENGLISH
ENGLISH
Rear
PS/2 keyboard/mouse combo port. This port is for a PS/2 keyboard/mouse.
USB 3.2 Gen 1 ports. These 9-pin Universal Serial Bus (USB) ports connect to USB 3.2
Gen 1 devices.
DVI-D port. This port is for any DVI-D compatible device.
• DVI-D can not be converted to output from RGB Signal to CRT and is not compatible with
DVI-I.
• The on-board DVI-D, VGA and HDMI® ports only work while using a CPU with integrated
graphics.
DVI-D VGA HDMI®
Ryzen CPU - Vermeer Not support Not support Not support
Ryzen CPU - Cezanne Support Support Support
Ryzen CPU - Renoir Support Support Support
Ryzen CPU - Matisse Not support Not support Not support
Ryzen APU - Picasso Support Support Support
ASUS G10DK 15
ENGLISH
ENGLISH
VGA port. This port is for VGA-compatible devices such as a VGA monitor.
HDMI® port. This port is for a High-Denition Multimedia Interface (HDMI®) connector,
and is HDCP compliant allowing playback of HD DVD, Blu-ray, and other protected
content.
USB 3.2 Gen 2 ports. These 9-pin Universal Serial Bus (USB) ports are for USB 3.2 Gen
2 devices.
We strongly recommend that you connect USB 3.2 Gen 2 devices to USB 3.2 Gen 2 ports for
faster and better performance for your USB 3.2 Gen 2 devices.
Microphone port (pink). This port connects to a microphone.
Line Out port (lime). This port connects to a headphone or speaker. In a 4, 5.1, or
7.1-channel conguration, the function of this port becomes Front Speaker Out.
Line In port (light blue). This port connects to a tape, CD, DVD player, or other audio
sources.
Refer to the audio conguration table below for the function of the audio ports in the 2, 4, 5.1,
or 7.1-channel conguration.
Audio 2, 4, 5.1, or 7.1-channel conguration
Port Headset 2-channel 4-channel 5.1-channel 7.1-channel
Light Blue (Rear panel) Line In Rear Speaker Out Rear Speaker Out Rear Speaker Out
Lime (Rear panel) Line Out Front Speaker Out Front Speaker Out Front Speaker Out
Pink (Rear panel) Mic In Mic In Bass/Center Bass/Center
Lime (Front panel) - - - Side Speaker Out
Power connector. Plug the power cord to this connector.
RATING: • 115Vac/230Vac, 9A/4.5A, 50Hz/60Hz (WW, TW)
• 220Vac, 4.5A, 50Hz (China)
Air vents. These vents allow air ventilation.
DO NOT block the air vents on the chassis. Always provide proper ventilation for your
computer.
LAN (RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN)
through a network hub.
16 Chapter 1: Getting started
ENGLISH
ENGLISH
LAN port LED indications
LAN port
SPEED LEDACT/LINK LED
Activity/Link LED Speed LED
Status Description Status Description
OFF No link OFF 10Mbps connection
ORANGE Linked ORANGE 100Mbps connection
BLINKING Data activity GREEN 1Gbps connection
ASUS Graphics Cards (on selected models only). The display output ports on these
optional ASUS Graphics Cards may vary with dierent models.
Expansion slot brackets. Remove the expansion slot bracket when installing an
expansion card.
ASUS G10DK 17
ENGLISH
ENGLISH
Setting up your computer
This section guides you through connecting the main hardware devices, such as the external
monitor, keyboard, mouse, and power cord to your computer.
Connecting an external monitor
Using the ASUS Graphics Card (on selected models only)
Connect your monitor to the display output port on the discrete ASUS Graphics Card.
To connect an external monitor using the ASUS Graphics Card:
1. Connect a monitor to a display output port on the ASUS Graphics Card.
2. Plug the monitor to a power source.
The display output ports on the ASUS Graphics Card may vary with dierent models.
18 Chapter 1: Getting started
ENGLISH
ENGLISH
Connecting a USB keyboard and a USB mouse
Connect a USB keyboard and a USB mouse to the USB ports on the rear panel of your computer.
`
Connecting the power cord
Connect one end of the power cord to the power connector on the rear panel of your computer
and the other end to a power source.
ASUS G10DK 19
ENGLISH
ENGLISH
Turning your computer ON
This section describes how to turn on your computer after setting up your computer.
To turn your computer ON:
1. Turn your monitor ON.
2. Press the power button on your computer.
Power button
3. Wait until the operating system loads automatically.
20 Chapter 1: Getting started
ENGLISH
ENGLISH
ASUS G10DK 21
ENGLISH
ENGLISH
Connecting a USB storage device
This desktop PC provides USB 3.2 Gen 1, and USB 3.2 Gen 2 ports on the front and rear panels. The
USB ports allow you to connect USB devices such as storage devices.
To connect a USB storage device:
• Insert the USB storage device to your computer.
Front panel
Rear panel
ENGLISH
ENGLISH
ASUS G10DK 22
Chapter 2
Connecting devices to your computer
Connecting headset
Connecting microphone and speakers
This desktop PC comes with microphone ports and speaker ports on both the front and rear
panels. The audio I/O ports located on the rear panel allow you to connect 2-channel, 4-channel,
5.1-channel, and 7.1-channel speakers.
Connecting 2-channel Speakers
ASUS G10DK 23
ENGLISH
ENGLISH
Connecting 4-channel Speakers
Connecting 5.1-channel Speakers
24 Chapter 2: Connecting devices to your computer
ENGLISH
ENGLISH
LINE OUT
Connecting 7.1-channel Speakers
ASUS G10DK 25
ENGLISH
ENGLISH
Connecting multiple external displays
Your desktop PC may come with VGA, HDMI®, or DVI ports and allows you to connect multiple
external displays.
Setting up multiple displays
When using multiple monitors, you are allowed to set display modes. You can use the additional
monitor as a duplicate of your main display, or as an extension to enlarge your Windows desktop.
To set up multiple displays:
1. Turn o your computer.
2. Connect the two monitors to your computer and connect the power cords to the monitors.
Refer to Setting up your computer section in Chapter 1 for details on how to connect a
monitor to your computer.
3. Turn on your computer.
4. From the Start menu, click Settings > System > Display.
5. Congure the settings for your displays.
For some graphic cards, only the monitor that is set to be the primary display has display during
POST. The dual display function works only under Windows.
26 Chapter 2: Connecting devices to your computer
ENGLISH
ENGLISH
Connecting an HDTV
Connect a High Denition TV (HDTV) to the HDMI® port of your computer.
• You need an HDMI® cable to connect the HDTV and the computer. The HDMI® cable is
purchased separately.
• To get the best display performance, ensure that your HDMI® cable is less than 15 meters.
ASUS G10DK 27
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ASUS G10DK 28
Chapter 3
Using your computer
Proper posture when using your Desktop PC
When using your Desktop PC, maintaining the proper posture is necessary to prevent strain to your
wrists, hands, and other joints or muscles. This section provides you with tips on avoiding physical
discomfort and possible injury while using and fully enjoying your Desktop PC.
Eye level to the top of
the monitor screen
Foot rest
90˚ angles
To maintain the proper posture:
• Position your computer chair to make sure that your elbows are at or slightly above the
keyboard to get a comfortable typing position.
• Adjust the height of your chair to make sure that your knees are slightly higher than your
hips to relax the backs of your thighs. If necessary, use a footrest to raise the level of your
knees.
• Adjust the back of your chair so that the base of your spine is rmly supported and angled
slightly backward.
• Sit upright with your knees, elbows and hips at an approximately 90º angle when you are at
the PC.
• Place the monitor directly in front of you, and turn the top of the monitor screen even with
your eye level so that your eyes look slightly downward.
• Keep the mouse close to the keyboard, and if necessary, use a wrist rest for support to
reduce the pressure on your wrists while typing.
• Use your Desktop PC in a comfortably-lit area, and keep it away from sources of glare such as
windows and straight sunlight.
• Take regular mini-breaks from using your Desktop PC.
ASUS G10DK 29
ENGLISH
ENGLISH
Wired connection
Use an RJ-45 cable to connect your computer to a DSL/cable modem or a local area network (LAN).
Connecting via a DSL/cable modem
To connect via a DSL/cable modem:
1. Set up your DSL/cable modem.
Refer to the documentation that came with your DSL/cable modem.
2. Connect one end of an RJ-45 cable to the LAN (RJ-45) port on the rear panel of your
computer and the other end to a DSL/cable modem.
LINE LAN RESET PWR
Modem
RJ-45 cable
3. Turn on the DSL/cable modem and your computer.
4. Congure the necessary Internet connection settings.
• Contact your network administrator for details or assistance in setting up your Internet
connection.
• For more details, refer to the sections Conguring a dynamic IP/PPPoE network connection
or Conguring a static IP network connection.
ENGLISH
ENGLISH
ASUS G10DK 30
Chapter 4
Connecting to the Internet
Connecting via a local area network (LAN)
To connect via a LAN:
1. Connect one end of an RJ-45 cable to the LAN (RJ-45) port on the rear panel of your
computer and the other end to your LAN.
LAN
RJ-45 cable
2. Turn on your computer.
3. Congure the necessary Internet connection settings.
• Contact your network administrator for details or assistance in setting up your Internet
connection.
• For more details, refer to the sections Conguring a dynamic IP/PPPoE network connection
or Conguring a static IP network connection.
ASUS G10DK 31
ENGLISH
ENGLISH
Conguring a dynamic IP/PPPoE network connection
To congure a dynamic IP/PPPoE network connection:
1. Launch Network and Sharing Center in either of these two ways:
a) From the taskbar, right-click , then click Open Network and Sharing Center.
b) From the Start menu, click Settings > Network & Internet > Ethernet > Network and
Sharing Center.
2. From the Open Network and Sharing Center screen, click Change Adapter settings.
3. Right-click on your LAN and select
Properties.
4. Click Internet Protocol Version 4(TCP/
IPv4) and click Properties.
5. Click Obtain an IP address automatically
and click OK.
Continue to the next steps if you are using PPPoE connection.
32 Chapter 4: Connecting to the Internet
ENGLISH
ENGLISH
7. Select Connect to the Internet and
click Next.
6. Return to the Network and
Sharing Center and then click
Set up a new connection or
network.
8. Select Broadband (PPPoE) and click
Next.
9. Follow the next onscreen instructions to
complete the setup.
Conguring a static IP network connection
To congure a static IP network connection:
1. Repeat steps 1 to 4 of the previous section.
2 Click Use the following IP address.
3. Enter the IP address, Subnet mask and Gateway
from your service provider.
4. If needed, enter the preferred DNS Server
address and alternative address.
5. When done, click OK.
ASUS G10DK 33
ENGLISH
ENGLISH
Wi-Fi connection (on selected models only)
Connect your computer to the Internet through a wireless connection.
To establish a wireless connection, you need to connect to a wireless access point (AP).
Wireless AP
Modem
To increase the range and sensitivity of the wireless radio signal, connect the external antennas to
the antenna connectors on the ASUS WLAN Card.
34 Chapter 4: Connecting to the Internet
ENGLISH
ENGLISH
ASUS G10DK 35
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ASUS G10DK 36
Chapter 5
Troubleshooting
Troubleshooting
This chapter presents some problems you might encounter and the possible solutions.
?
My computer cannot be powered on and the power LED on the front panel
does not light up.
• Check if your computer is properly connected.
• Check if the wall outlet is functioning.
• Check if the Power Supply Unit is switched on. Refer to the section Turning your
computer ON in Chapter 1.
?
My computer hangs.
• Do the following to close the programs that are not responding:
1. Simultaneously press <Alt> + <Ctrl> + <Delete> keys on the keyboard, then
click Task Manager.
2. Select the program that is not responding, then click End Task.
• If the keyboard is not responding, press and hold the Power button on the top of
your chassis until the computer shuts down. Then press the Power button to turn it
on.
?
I cannot connect to a wireless network using the ASUS WLAN Card (on
selected models only)?
• Ensure that you enter the correct network security key for the wireless network you
want to connect to.
• Connect the external antennas (optional) to the antenna connectors on the ASUS
WLAN Card and place the antennas on the top of your computer chassis for the
best wireless performance.
ASUS G10DK 37
ENGLISH
ENGLISH
?
The arrow keys on the number key pad are not working.
Check if the Number Lock LED is o. When the Number Lock LED is on, the keys on
the number key pad are used to input numbers only. Press the Number Lock key to
turn the LED o if you want to use the arrow keys on the number key pad.
?
No display on the monitor.
• Check if the monitor is powered on.
• Ensure that your monitor is properly connected to the video output port on your
computer.
• If your computer comes with a discrete graphics card, ensure that you connect your
monitor to a video output port on the discrete graphics card.
• Check if any of the pins on the monitor video connector is bent. If you discover
bent pins, replace the monitor video connector cable.
• Check if your monitor is plugged to a power source properly.
• Refer to the documentation that came with your monitor for more troubleshooting
information.
?
When using multiple monitors, only one monitor has display.
• Ensure that the both monitors are powered on.
• During POST, only the monitor connected to the VGA port has display. The dual
display function works only under Windows.
• When a graphics card is installed on your computer, ensure that you connect the
monitors to the output port on the graphics card.
• Check if the multiple displays settings are correct.
?
My computer cannot detect my USB storage device.
• The rst time you connect your USB storage device to your computer, Windows
automatically installs a driver for it. Wait for a while and go to My Computer to
check if the USB storage device is detected.
• Connect your USB storage device to another computer to test if the USB storage
device is broken or malfunctions.
38 Chapter 5: Troubleshooting
ENGLISH
ENGLISH
?
I want to restore or undo changes to my computer’s system settings
without aecting my personal les or data.
You can use Windows® 11 Refresh your PC without aecting your les recovery
option to restore or undo changes to your computer’s system settings without
aecting your personal data such as documents or photos. To use this recovery
option, click Settings > Update & recovery > Recovery from the Start menu,
select Refresh your PC without aecting your les, and click Get started.
?
The picture on the HDTV is distorted.
• It is caused by the dierent resolutions of your monitor and your HDTV. Adjust the
screen resolution to t your HDTV. To change the screen resolution:
• From the Start menu, click Settings > System > Display.
?
My speakers produce no sound.
• Ensure that you connect your speakers to the Line out port (lime) on the front panel
or the rear panel.
• Check if your speak is connected to an electrical source and turned on.
• Adjust your speakers’ volume.
• Ensure that your computer’s system sounds are not Muted.
• If it is muted, the volume icon is displayed as . To enable the system
sounds, click from the Windows notication area, then click .
• If it is not muted, click and drag the slider to adjust the volume.
• Connect your speakers to another computer to test if the speakers arer working
properly.
?
The DVD drive cannot read a disc.
• Check if the disc is placed with the label side facing up.
• Check if the disc is centered in the tray, especially for the discs with
non-standard size or shape.
• Check if the disc is scratched or damaged.
?
The DVD drive eject button is not responding.
1. From the Start menu, click File Explorer.
2. Right-click , then click Eject from the menu
ASUS G10DK 39
ENGLISH
ENGLISH
Power
Problem Possible Cause Action
No power
(The power
indicator is o)
Incorrect power voltage
• Set your computer’s power voltage
switch to your area’s power
requirements.
• Adjust the voltage settings. Ensure that
the power cord is unplugged from the
power outlet.
Your computer is not turned
on.
Press the power key on the front panel to
ensure that your computer is turned on.
Your computer’s power cord
is not properly connected.
• Ensure that the power cord is properly
connected.
• Use other compatible power cord.
PSU (Power supply unit)
problems
Contact the ASUS Service Center about
installing another PSU on your computer.
Display
Problem Possible Cause Action
No display output
after turning the
computer on
(Black screen)
The signal cable is not
connected to the correct
VGA port on your computer.
• Connect the signal cable to the correct
display port (onboard VGA or discrete
VGA port).
• If you are using a discrete VGA card,
connect the signal cable to the discrete
VGA port.
Signal cable problems Try connecting to another monitor.
40 Chapter 5: Troubleshooting
ENGLISH
ENGLISH
LAN
Problem Possible Cause Action
Cannot access the
Internet
The LAN cable is not
connected.
Connect the LAN cable to your
computer.
LAN cable problems
Ensure the LAN LED is on. If not, try
another LAN cable. If it still does not
work, contact the ASUS service center.
Your computer is not
properly connected to a
router or hub.
Ensure that your computer is properly
connected to a router or hub.
Network settings Contact your Internet Service Provider
(ISP) for the correct LAN settings.
Problems caused by the anti-
virus software Close the anti-virus software.
Driver problems Reinstall the LAN driver
Audio
Problem Possible Cause Action
No Audio
Speaker or headphone is
connected to the wrong port.
• Refer to your computer’s User Guide
for the correct port.
• Disconnect and reconnect the speaker
to your computer.
Speaker or headphone does
not work.
Try using another speaker or
headphone.
The front and back audio
ports do not work.
Try both the front and back audio ports.
If one port failed, check if the port is set
to multi-channel.
Driver problems Reinstall the audio driver
ASUS G10DK 41
ENGLISH
ENGLISH
System
Problem Possible Cause Action
System speed is
too slow
Too many programs are
running. Close some of the programs.
Computer virus attack
• Use an anti-virus software to scan for
viruses and repair your computer.
• Reinstall the operating system.
The system often
hangs or freezes.
Hard disk drive failure
• Send the damaged hard disk drive to
ASUS Service Center for servicing.
• Replace with a new hard disk drive.
Memory module problems
• Replace with compatible memory
modules.
• Remove the extra memory modules
that you have installed, then try again.
• Contact the ASUS Service Center for
assistance.
There is not enough
air ventilation for your
computer.
Move your computer to an area with
better air ow.
Incompatible softwares are
installed.
Reinstall the OS and reinstall
compatible softwares.
42 Chapter 5: Troubleshooting
ENGLISH
ENGLISH
CPU
Problem Possible Cause Action
Too noisy right
after turning on the
computer.
Your computer is booting up.
It is normal. The fan runs on its full
speed when the computer is powering
on. The fan slows down after entering
the OS.
The BIOS settings have been
changed. Restore the BIOS to its default settings.
Old BIOS version
Update the BIOS to the latest version.
Visit the ASUS Support site at https://
www.asus.com/support to download
the latest BIOS versions.
Computer is too
noisy when in use.
The CPU fan has been
replaced.
Ensure that you are using a compatible
or ASUS-recommended CPU fan.
There is not enough air
ventilation for the computer.
Ensure that your computer is working
in an area with good air ow.
The system temperature is
too high.
• Update the BIOS.
• If you know how to reinstall the
motherboard, try to clean the inner
space of the chassis.
• Contact the ASUS Service Center for
assistance.
If the problem still persists, refer to your Desktop PC’s warranty card and contact the ASUS Service
Center. Visit the ASUS Support site at https://www.asus.com/support for the service center
information.
ASUS G10DK 43
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ASUS G10DK 44
Appendix
Working with Windows®
Starting for the rst time
When you start your computer for the rst time, a series of screens appear to guide you in
conguring your Windows® operating system. Follow the onscreen instructions to congure the
following basic items:
• Personalize
• Get online
• Settings
• Your account
After conguring the basic items, Windows® proceeds to install your apps and preferred settings.
Ensure that your computer is kept powered on during the setup process. Once the setup process is
complete, the Desktop appears.
The screenshots in this chapter are for reference only.
Start menu
The Start menu is the main gateway to your computer’s programs, Windows® apps, folders, and
settings. You can use the Start menu to do these common activities:
• Start programs or Windows® apps
• Open commonly used programs or Windows® apps
• Adjust computer settings
• Get help with the Windows® operating system
• Turn o your computer
• Log o from Windows® or switch to a dierent user account
Launching the Start menu
You can launch the Start menu in two ways:
• Position your mouse pointer over the Start icon on your desktop then click it.
• Press the Windows® logo key on your keyboard.
ASUS Desktop PC 45
ENGLISH
ENGLISH
Opening programs from the Start menu
One of the most common uses of the Start menu is opening programs installed on your Computer.
You can open programs in two ways:
• Position your mouse pointer over the program then click to launch it.
• Use the arrow keys to browse through the programs. Press to launch it.
Windows® apps
Some Windows® apps require signing in to your Microsoft account before they are fully launched.
Launching Windows® apps from the Start menu
You can launch Windows® apps in two ways:
• Position your mouse pointer over the app then click to launch it.
• Use the arrow keys to browse through the apps. Press to launch an app.
Connecting to wireless networks
Wi-Fi
Access emails, surf the Internet, and share applications via social networking sites using your
computer’s Wi-Fi connection.
Connecting Wi-Fi
Connect your computer to a Wi-Fi network by using the following steps:
1. Click/Tap the Wi-Fi icon from the taskbar to enable Wi-Fi.
2. Select an access point from the list of available Wi-Fi connections.
3. Select Connect to start the network connection.
You may be prompted to enter a security key to activate the Wi-Fi connection.
Bluetooth
Use Bluetooth to facilitate wireless data transfers with other Bluetooth-enabled devices.
Pairing with other Bluetooth-enabled devices
You need to pair your computer with other Bluetooth-enabled devices to enable data transfers.
Connect your devices by using the following steps:
1. Launch Settings from the Start menu.
2. Select Devices > Bluetooth to search for Bluetooth-enabled devices. (for Windows® 10)
Select Bluetooth & devices > Add device to search for Bluetooth-enabled devices.
(for Windows® 11)
46 Appendix: Working with Windows®
ENGLISH
ENGLISH
3. Select a device from the list to pair your computer with the device.
For some Bluetooth-enabled devices, you may be prompted to key in the passcode of your
computer.
Connecting to wired networks
You can also connect to wired networks, such as local area networks and broadband Internet
connection, using your computer’s LAN port.
Contact your Internet Service Provider (ISP) for details or your network administrator for
assistance in setting up your Internet connection.
Turning your computer o
You can turn o your computer by doing either of the following procedures:
• Launch the Start menu, select the power icon then select Shut down to do a normal
shutdown.
From the log-in screen, select the power icon then select Shut down.
• Press to launch Shut Down Windows. Select Shut down from the drop-
down list then select OK.
If your computer is unresponsive, press and hold the power button for at least four (4)
seconds until your computer turns o.
Putting your computer to sleep
You can put your computer to Sleep mode in two ways:
• Launch the Start menu, select the power icon then select Sleep to put your computer to
sleep.
From the log-in screen, select the power icon then select Sleep.
• Press to launch Shut Down Windows. Select Sleep from the drop-down list
then select OK.
You can also put your computer to Sleep mode by pressing the power button once.