Table of Contents
- Contents
- Notices
- Safety information
- Care & Cleaning
- Takeback Services
- Product information for EU energy label
- Chapter 1: Product introduction
- 1.1 Welcome!
- 1.2 Package contents
- 1.3 Monitor introduction
- Chapter 2: Setup
- 2.1 Monitor standing positions
- 2.2 Adjusting the monitor
- 2.3 Connecting the cables
- 2.4 Turning on the monitor
- 2.5 Performing wireless projection
- 2.6 Connecting the monitor to the Internet
- 2.7 Updating wireless projection firmware
- 2.8 Announcements
- Chapter 3: General instructions
- 3.1 OSD (On-Screen Display) menu
- 3.2 Specifications summary
- 3.3 Outline dimensions
- 3.4 Troubleshooting (FAQ)
- 3.5 Supported operating modes
ASUS MB16AWP User Manual
Displayed below is the user manual for MB16AWP by ASUS which is a product in the Computer Monitors category. This manual has pages.
Related Manuals
MB16AWP
Wireless Portable Monitor
User Guide
SECS
2
ii
First Edition
January 2022
Copyright © 2022 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless
such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM
ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN
THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the
owners’ benet, without intent to infringe.
iii
Contents
Contents ...................................................................................................... iii
Notices ......................................................................................................... iv
Safety information .................................................................................... viii
Care & Cleaning .......................................................................................... ix
Takeback Services ....................................................................................... x
Product information for EU energy label ................................................... x
Chapter 1: Product introduction
1.1 Welcome! .................................................................................... 1-1
1.2 Package contents ......................................................................... 1-1
1.3 Monitor introduction .................................................................... 1-2
1.3.1 Front/Side view ............................................................... 1-2
Chapter 2: Setup
2.1 Monitor standing positions ......................................................... 2-1
2.2 Adjusting the monitor .................................................................. 2-1
2.3 Connecting the cables ................................................................. 2-2
2.4 Turning on the monitor ................................................................ 2-2
2.5 Performing wireless projection .................................................. 2-3
2.6 Connecting the monitor to the Internet ...................................... 2-4
2.7 Updatingwirelessprojectionrmware ...................................... 2-5
2.8 Announcements ........................................................................... 2-6
Chapter 3: General instructions
3.1 OSD (On-Screen Display) menu ................................................ 3-1
3.1.1 How to recongure .......................................................... 3-1
3.1.2 OSD function introduction ............................................... 3-2
3.2 Specicationssummary .............................................................. 3-9
3.3 Outline dimensions .................................................................... 3-11
3.4 Troubleshooting (FAQ) .............................................................. 3-12
3.5 Supported operating modes ..................................................... 3-14
iv
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modications
to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
FCC Caution and Label
• Distance < 20cm, with SAR requirement
RF Exposure Information (SAR)
This device meets the government’s requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy set by the Federal Communications
Commission of the U.S. Government.
v
The exposure standard employs a unit of measurement known as the Specic
Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR
are conducted using standard operating positions accepted by the FCC with the
EUT transmitting at the specied power level in different channels.
The FCC has granted an Equipment Authorization for this device with all reported
SAR levels evaluated as in compliance with the FCC RF exposure guidelines.
SAR information on this device is on le with the FCC and can be found under the
Display Grant section of www.fcc.gov/eot/ea/fccid after searching on "Contains
FCC ID: PANP31ASUS".
For module caution
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may
be installed such that 20cm may be maintained between the antenna and users.
The nal end product must be labeled in a visible area with the following: "Contains
FCC ID: PANP31ASUS” and "Contains IC: 6225A-P31ASUS“
Information for the OEMs and Integrators
The following statement must be included with all versions of this document
supplied to an OEM or integrator, but should not be distributed to the end user.
1) This device is intended for OEM integrators only.
2) Please see the full Grant of Equipment document for other restrictions.
5GHz Device STATEMENT
MASTER EQUIPMENT:
The availability of some specic channels and / or operational frequency bands are
country dependent and are rmware programmed at factory to match the intended
destination. The rmware setting is not accessible by the end user.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
This Class B digital apparatus meets all requirements of the Canadian
Interference - Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Réglement sur le matériel brouiller du Canada.
vi
Canada IC
Canada, Industry Canada (IC) Notices
This device complies with Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Canada, avis d'Industry Canada (IC)
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
RF Exposure
Distance < 20 cm , with SAR requirement (RSS-102 section 2.6)
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry
Canada (IC) radio frequency exposure limits. The Wireless Device should
be used in such a manner such that the potential for human contact during
normal operation is minimized.
This device has been evaluated for and shown compliant with the IC
Specific Absorption Rate (“SAR”) limits when operated in portable
exposure conditions.
Informations concernant l'exposition aux fréquences radio (RF)
La puissance de sortie émise par l’appareil de sans l est inférieure à la
limite d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez
l’appareil de sans fil de façon à minimiser les contacts humains lors du
fonctionnement normal.
Ce dispositif a été évalué pour et démontré conforme à la Taux IC
d'absorption spécifique ("SAR") des limites lorsqu'il est utilisé dans des
vii
conditions d'exposition portatifs.
For 5150~5250MHz Band:
This device is for indoor use only when operated in the frequency band
5150 ~5250 MHz
Ce dispositif est limité à une utilisation en intérieur seulement dans la
bande 5150-5250 MHz.
The WiFi operating in the band 5150-5350MHz shall be restricted to indoor
use for country listed below:
UK
Complies with
IMDA Standards
DB103778
viii
Safety information
• Before setting up the monitor, carefully read all the documentation that came
with the package.
• To prevent re or shock hazard, never expose the monitor to rain or moisture.
• Never try to open the monitor cabinet. The dangerous high voltages inside the
monitor may result in serious physical injury.
• If the power supply is broken, do not try to x it by yourself. Contact a qualied
service technician or your retailer.
• Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
• Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or over a
radiator or heat source unless proper ventilation is provided.
• The monitor should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.
• Use the appropriate power plug which complies with your local power standard.
• Do not overload power strips and extention cords. Overloading can result in re
or electric shock.
• Avoid dust, humidity, and temperature extremes. Do not place the monitor in
any area where it may become wet. Place the monitor on a stable surface.
• Unplug the unit during a lightning storm or if it will not be used for a long period
of time. This will protect the monitor from damage due to power surges.
• Never push objects or spill liquid of any kind into the slots on the monitor
cabinet.
• To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate congured receptacles marked between
100-240V AC.
• If you encounter technical problems with the monitor, contact a qualied
service technician or your retailer.
• Adjustment of the volume control as well as the equalizer to other settings
than the center position may increase the ear-/headphones output voltage and
therefore the sound pressure level.
• The adapter is only used for this monitor, do not use it for other purpose.
Your device uses one of the following power supplies:
- Manufacturer: Delta Electronics Inc., Model: ADP-45HG B
ix
This symbol of the crossed out wheeled bin indicates that the product (electrical,
electronic equipment, and mercury-containing button cell battery) should not
be placed in municipal waste. Please check local regulations for disposal of
electronic products.
AEEEyönetmeliğineuygundur
Care & Cleaning
• Before you lift or reposition your monitor, it is better to disconnect the cables
and power cord. Follow the correct lifting techniques when positioning the
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.
Do not lift the display by the stand or the cord.
• Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed
with a cloth dampened with mild cleaner.
• Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended
for use with the monitor. Never spray cleaner directly on the screen, as it may
drip inside the monitor and cause an electric shock.
The following symptoms are normal with the monitor:
• You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
• When the same image is displayed for hours, an afterimage of the previous
screen may remain after switching the image. The screen will recover slowly or
you can turn off the Power Switch for hours.
• When the screen becomes black or ashes, or cannot work anymore, contact
your dealer or service center to x it. Do not repair the screen by yourself!
• (For OLED models) Damage resulting from long-term static images displayed
(also referred as “Image Sticking”) or improper use.
• (For OLED models) Defect of color accuracy shift resulting from display color
decay accelerated by user’s behaviors.
Conventions used in this guide
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying
to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
x
Wheretondmoreinformation
Refer to the following sources for additional information and for product and
software updates.
1. ASUS websites
The ASUS websites worldwide provide updated information on ASUS
hardware and software products. Refer to http://www.asus.com
2. Optional documentation
Your product package may include optional documentation that may have
been added by your dealer. These documents are not part of the standard
package.
Takeback services
ASUS recycling and takeback programs come from our commitment to the highest
standards for protecting our environment. We believe in providing solutions for
our customers to be able to responsibly recycle our products, batteries and other
components as well as the packaging materials.
Please go to http://csr.asus.com/english/Takeback.htm for detail recycling
information in different region.
Rechargeable battery recycling service in
north America
For US and Canada customers, you can call 1-800-822-8837
(toll-free) for recycling information of your ASUS products'
rechargeable batteries.
Product information for EU energy label
1-1ASUS Wireless Portable Monitor MB16A
1.1 Welcome!
Thank you for purchasing the ASUS® Wireless Portable Monitor!
The latest ASUS Wireless Portable Monitor provides great portability and simplicity
to your daily life, enhancing both of your viewing experience and style.
1.2 Package contents
Check your package for the following items:
Wireless portable monitor
Quick start guide
Warranty card
Power adapter
Power cord
USB Type-C to Type-C cable
HDMI to HDMI mini adapter
Sleeve
ZenScreen tripod hole cover
If any of the above items is damaged or missing, contact your retailer
immediately.
1-2 Chapter 1: Product introduction
1.3 Monitor introduction
1.3.1 Front/Side view
SECS
2
12
9
8
10
11
Main Menu
Close
Volume
Input Select
Brightness
Main Menu
Close
Volume
Input Select
Brightness
3
4
5
6
7
1. Power button/power indicator
• Turns the monitor on (long press for 2 seconds)/off.
• The color denition of the power indicator is as the below table.
Status Description
Blue On mode
Blue ashing Saving mode
Off Off mode - Not charging
Red Off mode - Charging
Green Off mode - Finished charging
2. 5-way button
• Turns on the button functions menu. Enacts the selected OSD menu
item.
• Increases/Decreases values or moves your selection up/down/left/
right.
3. Main Menu
• Press the 5-way button once to enter the button functions menu when the
OSD is off. Press this button again to enter the OSD menu.
4. Close
• Move the 5-way button left to close the button functions menu.
• Move the 5-way button left for over 5 seconds to toggle the Key Lock
function between on and off.
5. Volume
• Move the 5-way button right to enter the volume menu.
1-3ASUS Wireless Portable Monitor MB16A
6. Input Select
• Move the 5-way button up to enter the Input Select menu.
7. Brightness
• Move the 5-way button down to enter the Brightness menu.
8. Earphone jack
9. Mini HDMI port
• This port is for connection with an HDMI compatible device.
10. USB Type-C port
• This port is for connection with an USB Type-C compatible device.
11. USB Type-C port
• This port connects the power adapter.
1-4 Chapter 1: Product introduction
2-1ASUS Wireless Portable Monitor MB16A
2.1 Monitor standing positions
You can stand up the monitor in the following positions.
SECS
2
A B
SECS
2
2.2 Adjusting the monitor
• For optimal viewing, we recommend that you look at the full face of the
monitor, then adjust the monitor to the angle that is most comfortable for you.
• Hold the stand to prevent the monitor from falling when you change its angle.
• You can adjust the monitor’s angle at 0˚ ~ 70˚.
SECS
2
+70°
(Tilt)
2-2 Chapter 2: Setup
2.3 Connecting the cables
A
B
Type-C
Type-C
SECS
2
SECS
2
HDMI
Mini HDMI
or
2.4 Turning on the monitor
Press and hold the power button for 2 seconds. See page 1-2 for the location of
the power button. The power indicator lights up in blue to show that the monitor
is ON. The start up process takes about 30 seconds.
SECS
2
We suggest you charge the monitor before using it for the rst time.
2-3ASUS Wireless Portable Monitor MB16A
When there is no input signal or no action made on the OSD menu for around
6 minutes when the signal source is "Wireless" or for one hour when the signal
source is not HDMI or USB Type-C without power supply, the monitor will turn
off automatically. To turn on the monitor, press and hold the power button for 2
seconds.
2.5 Performing wireless projection
1. Make sure that the signal source for the monitor is "Wireless".
2. For different devices, follow the steps below.
»For Windows OS devices
* Press the Windows logo key + K and choose the monitor.
»For Android devices
* After opening the Quick settings panel, press the Miracast icon and
choose the monitor.
»For iOS devices
1. Select MB16AWP in available Wi-Fi networks.
(SSID MB16AWP-********)
2. Insert the password shown on the monitor.
3. After opening control center, press screen mirroring and choose the
monitor to start projection.
»For MacOS devices
1. Select MB16AWP in available Wi-Fi networks.
(SSID MB16AWP-********)
2. Insert the password shown on the monitor.
3. Activate screen mirroring, and choose the monitor to start
projection.
»For Chromebooks
1. Download “EZCast” extension in Chrome store.
2. Add “EZCast” extension to Chrome.
3. Select MB16AWP in available Wi-Fi networks.
(SSID MB16AWP-********)
4. Insert the password shown on the monitor.
5. Open the EZCast APP.
6. Click Search Devices and select the monitor.
7. Enable the mirroring function to start wireless projection.
Please note that content from platforms with Digital rights management (DRM)
enabled, ex: Hulu, Netix, Apple TV+, Disney+, is unable to be cast using
wireless projection.
2-4 Chapter 2: Setup
2.6 Connecting the monitor to the
Internet
1. Turn on the monitor and make sure that the signal source is "Wireless".
2. Make sure both or your device and the monitor are in the same subnetwork
(connecting MB16AWP in the Wi-Fi settings on your device.).
3. Open your web browser and go to the address of the monitor (192.168.203.1).
SECS
2
http://192.168.203.1
192.168.203.1
4. Select a WiFi network that you want to join.
5. Enter the password if asked.
2-5ASUS Wireless Portable Monitor MB16A
2.7 Updatingwirelessprojectionrmware
1. Make sure that the monitor connects to the Internet.
2. After the monitor successfully connects to the Internet, new IP address will
be assigned to the monitor and displayed on the upper right corner of the
monitor.
3. Connect your device to the same WiFi network as the monitor.
4. Open the web browser on your device and go to the IP address of the monitor
(displayed on the upper right corner of the monitor). If there's newer version
of rmware available, click OK to start the update.
5. Once conrmed, the monitor will start the process and reboot itself when
nished.
2-6 Chapter 2: Setup
If the monitor is up to date with the latest rmware, the following message will
appear.
2.8 Announcements
As this product includes magnet in the structure, there could be potential risk to
cause the damage of computer hard disc and objects that are sensitive to magnet.
Please ensure not to stack the product with the computer when computer is in use
(power on or standby mode) otherwise the hard drive could possibly be inuenced
by the result of permanent data missing or the computer display could be switched
off due to computer auto protection mechanism. When placing this product
together with the computer in a bag, you must have the computer power off to
avoid possible hard drive damage.
SECS
2
SECS
2
3-1ASUS Wireless Portable Monitor MB16A
3.1 OSD (On-Screen Display) menu
3.1.1 How to reconfigure
Standard Mode
sRGB Mode
Scenery Mode
Theater Mode
Game Mode
Night View Mode
Reading Mode
Darkroom Mode
Splendid ASUS MB16AWP 80
Scenery Mode Wireless 1920 x 1080 @ 60Hz
1. Press the 5-way button twice to activate the OSD menu.
2. Move the 5-way button (left, right, up, or down) to toggle between options
in the menu. As you move from one icon to another, the option name is
highlighted.
3. To select the highlighted item on the menu, push the button.
4. Move the 5-way button or to select the desired parameter or adjust the
parameter value on the slide bar.
5. Move the 5-way button once to return to previous menu or button
repeatedly to exit the OSD menu.
3-2 Chapter 3: OSD (On-Screen Display) menu
3.1.2 OSD function introduction
1. Splendid
This function contains 8 sub-functions you can select for your preference.
Each mode has the Reset selection, allowing you to maintain your setting or
return to the preset mode.
Standard Mode
sRGB Mode
Scenery Mode
Theater Mode
Game Mode
Night View Mode
Reading Mode
Darkroom Mode
Splendid ASUS MB16AWP 80
Scenery Mode Wireless 1920 x 1080 @ 60Hz
• Standard Mode: Best choice for document editing with Splendid Video
Enhancement.
Standard Mode meets Energy Star® requirements.
• sRGB Mode: best choice for viewing photos and graphics from PCs.
• Scenery Mode: Best choice for scenery photo display with Splendid
Video Enhancement.
• Theater Mode: Best choice for movies with Splendid Video
Enhancement.
• Game Mode: Best choice for game playing with Splendid Video
Enhancement.
• Night View Mode: Best choice for dark-scene games or movies with
Splendid Video Enhancement.
• Reading Mode: This is the best choice for book reading.
• Darkroom Mode: This is the best choice for a weak ambient light
environment.
• In the Standard mode, the following function(s) are not user-configurable:
Saturation, Skin Tone, Sharpness, ASCR.
• In the sRGB mode, the following function(s) are not user-configurable:
Brightness, Contrast, Saturation, Color Temp., Skin Tone, Sharpness,
ASCR.
• In the Reading mode, the following function(s) are not user-congurable:
Contrast, Saturation, Color Temp., Skin Tone, Sharpness, ASCR.
3-3ASUS Wireless Portable Monitor MB16A
2. Blue Light Filter
In this function, you can adjust the blue light filter level.
ASUS MB16AWP 80
Scenery Mode Wireless 1920 x 1080 @ 60Hz
Level 0
Level 1
Level 2
Level 3
Level 4
Blue Light Filter
• Level 0: No change.
• Level 1~4: The higher the level, the less blue light is scattered.
When Blue Light Filter is activated,the default settings of Standard Mode
will be automatically imported. Between Level 1 to Level 3, the Brightness
function is user-configurable. Level 4 is optimized setting. It is compliant
with TUV Low Blue Light Certification. The Brightness function is not user-
configurable.
Please refer to the following to alleviate eye strains:
• Users should take some time away from the display if working for long
hours. It is advised to take short breaks (at least 5 mins) after around 1
hour of continuous working at the computer. Taking short and frequent
breaks is more effective than a single longer break.
• To minimize eye strain and dryness in your eyes, users should rest the eye
periodically by focusing on objects that are far away.
• Eye exercises can help to reduces eye strain. Repeat these exercises
often. If eye strain continues please consult a physician. Eye exercises: (1)
Repeating look up and down (2) Slowly roll your eyes (3) Move your eyes
diagonal.
• High energy blue light may lead to eye strain and AMD (Age-Related
Macular Degeneration). Blue light Filter to reduce 70% (max.) harmful blue
light to avoiding CVS (Computer Vision Syndrome).
3-4 Chapter 3: OSD (On-Screen Display) menu
3. Color
Set a desired color setting from this menu.
ASUS MB16AWP 80
Scenery Mode Wireless 1920 x 1080 @ 60Hz
Brightness
Contrast
Saturation
Color Temp.
Skin Tone
Color
• Brightness: The adjusting range is from 0 to 100.
• Contrast: The adjusting range is from 0 to 100.
• Saturation: The adjusting range is from 0 to 100.
• Color Temp.: Contains 4 modes including Cool, Normal, Warm and User
Mode.
• Skin Tone: Contains three color modes including Reddish, Natural, and
Yellowish.
4. Image
Set the image related setting from this menu.
ASUS MB16AWP 80
Scenery Mode Wireless 1920 x 1080 @ 60Hz
Sharpness
Trace Free
Aspect Control
VividPixel
ASCR
Image
• Sharpness: The adjusting range is from 0 to 100.
• Trace Free: Adjusts the response time of the monitor.
• Aspect Control: Adjusts the aspect ratio to Full or 4:3.
4:3 is only available when input source is in 4:3 format.
• VividPixel: Enhances the outline of the displayed picture and generates
high-quality images on screen.
• ASCR: Turns on/off the ASCR (ASUS Smart Contrast Ratio) function.
3-5ASUS Wireless Portable Monitor MB16A
5. Input Select
In this function, you can select your desired input source.
ASUS MB16AWP 80
Scenery Mode Wireless 1920 x 1080 @ 60Hz
HDMI
USB Type-c
Wireless
Input Select
6. System Setup
Allows you to adjust the system.
ASUS MB16AWP 80
Scenery Mode Wireless 1920 x 1080 @ 60Hz
Splendid Demo Mode
Auto Rotation
ECO Mode
Volume
GamePlus
QuickFit
OSD Setup
More
System Setup
• Splendid Demo Mode: Splits the screen into two for Splendid modes
comparison. (Scenery mode only)
• Auto Rotation: To enable or disable automatic image rotation. For HDMI/
USB Type-C signal source, this function is only working under Windows
OS after installing the DisplayWidget software.
• ECO Mode: Reduces power consumption.
• Volume: The adjusting range is from 0 to 100.
• GamePlus: The GamePlus function provides a toolkit and creates a
better gaming environment for users when playing different types of
games. The crosshair overlay with different crosshair options lets you
choose the one that best suits the game you’re playing. There’s also an
onscreen timer you can position on the left of the display so you can keep
track of the elapsed gaming time. Display Alignment displays alignment
lines on 4 sides of the screen, serving as an easy and handy tool for you
to line up multiple monitors perfectly.
3-6 Chapter 3: OSD (On-Screen Display) menu
GamePlus Main Menu GamePlus — Crosshair
GamePlus
TimerCrosshair
(Practice Mode)
Display Alignment
GamePlus — Timer GamePlus — Timer — Position
Position
• QuickFit: You can have a preview of the document or photo layout
directly on screen without printing test copies.
* Alignment: This facilitates designers and users to organize
content and layout on one page and achieve a consistent look
and feel.
Alignment Grid 1 Alignment Grid 2
Alignment Grid 1
Alignment Grid 2
* Photo: The various real photo sizes displayed provides
photographers and other users to accurately view and edit their
photos in real size on the screen.
Photo 4x6, 3x5
4x6 3x5 4x6 3x5
3-7ASUS Wireless Portable Monitor MB16A
• OSD Setup:
* Adjusts the OSD timeout from 10 to 120 seconds.
* Enables or disables the DDC/CI function.
* Adjusts the OSD background from opaque to transparent.
• Language: There are 22 languages for your selection, including English,
French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech,
Croatian, Polish, Romanian, Hungarian, Turkish, Simplied Chinese,
Traditional Chinese, Japanese, Korean, Thai, Indonesian, Persian,
Ukrainian.
• Key Lock: To disable all function keys. Move the 5-way button left for
over 5 seconds to cancel the key lock function.
• Wi-Fi Setting:
* 5G/2.4G: Selects 5GHz or 2.4GHz as the frequency band for the
wireless network of the monitor.
* Reset: Resetting the Wi-Fi settings of the monitor when you
want to forget the Wi-Fi network. This process will take about 30
seconds.
• Information: Shows the monitor information.
• Power Indicator: Turns the power LED indicator on/off.
• Power Key Lock: Enables or disables the power key.
• All Reset: “Yes” allows you to restore the default settings.
7. Shortcut
Defines the function for the Shortcut button.
ASUS MB16AWP 80
Scenery Mode Wireless 1920 x 1080 @ 60Hz
Shortcut
Shortcut
Shortcut
Shortcut
• Shortcut: Selects a function for the Shortcut button.
3-8 Chapter 3: OSD (On-Screen Display) menu
When a certain function is selected or activated, your shortcut key may not
support. Available function choices for shortcut: Blue Light Filter, Splendid,
Brightness, Contrast, Auto Rotation, Input Select, Volume, Color Temp.,
QuickFit, GamePlus.
8. MyFavorite
Loads/Saves all settings on the monitor.
ASUS MB16AWP 80
Scenery Mode Wireless 1920 x 1080 @ 60Hz
Setting 1
Setting 2
Setting 3
Setting 4
MyFavorite
3-9ASUS Wireless Portable Monitor MB16A
3.2 Specicationssummary
Panel Type TFT LCD
Panel size
15.6” (16:9, 39.49 cm) wide screen
Max. Resolution 1920 x 1080
Pixel pitch 0.17925 mm
Brightness (Typ.) 250 cd/m2
Contrast Ratio (Typ.) 1200:1
Viewing angle (H/V) CR>10 178˚/178˚
Display colors 16.7 M
Color gamut sRGB 100%
Response time < 5 ms
Splendid Video Enhancement No
Splendid selection 8 video preset modes
Auto adjustment No
Color temperature selection 4 color temperatures
Analog input No
Digital input
Mini HDMI, USB Type-C (DP alt mode), Wireless
Earphone jack Yes
Speaker (Built-in) 1 W x 2
Colors Gun metal
Power LED Blue (On)/Blue ashing (Saving mode)/Off (Off)/Red
(Charging)/Green (Finished charging)
Tilt 0°~70°
Pivot +90°
DC input voltage DC: 9V 3A
Power consumption Power On: < 7.6 W** (Typ.), Standby: < 0.5 W, Power
Off: < 0.3 W
Temperature (Operating) 0˚C~40˚C
Temperature (Non-operating) -20˚C~+60˚C
Dimension (W x H x D) 357.9 x 224.8 x 11.5 mm
446 x 291 x 139 mm (package)
Weight (Esti.) 1.1 kg (net); 2.3 kg (gross)
Multi-languages 22 languages (English, French, German, Italian,
Spanish, Dutch, Portuguese, Russian, Czech,
Croatian, Polish, Romanian, Hungarian, Turkish,
Simplied Chinese, Traditional Chinese, Japanese,
Korean, Thai, Indonesian, Persian, Ukrainian)
Accessories Quick start guide, warranty card, power adapter,
power cord, USB Type-C to Type-C cable, HDMI to
HDMI mini adapter, sleeve, ZenScreen tripod hole
cover
3-10 Chapter 3: OSD (On-Screen Display) menu
Compliance and Standards
cTUVus, CB, CE, ErP, FCC, RCM, BSMI, VCCI,
RoHS, J-MOSS,WEEE, Windows 10 &11 WHQL, TUV-
Low Blue Light, PC-Recycle, UkrSEPRO, ICES-3, EU
Energy Label, VCCI, CU, CCC, KC, KCC, VN MEPS,
BIS, TUV-Flicker Free, PSE, CEC, CEL, MEPS,
E-Standby
*Specications are subject to change without notice.
**Measuring a screen brightness of 200 nits without audio/USB/Card reader connection.
3-11ASUS Wireless Portable Monitor MB16A
3.3 Outlinedimensions
357.9
[14.09]
224.8
[8.85]
23.6
[0.93]
6.2
[0.24]
6.2
[0.24]
6.2
[0.24]
12.7
[0.50]
8.7
[0.34]
27.0
[1.06]
345.6
[13.61]
344.2
[13.55]
195.0
[7.68]
193.6
[7.62]
29.1
[1.14]
29.1
[1.14]
10.5
[0.41]
70.00
135.9
[5.35]
178.4
[7.02]
E
ASUS MB16ACV Outline Dimension
*Unit: mm(inch)
3-12 Chapter 3: OSD (On-Screen Display) menu
3.4 Troubleshooting(FAQ)
Problem Possible Solution
Power LED is not ON • Connect to the ASUS adapter and check if
the battery is low; if so, charge the battery
before using it.
• Press and hold the button for 2
seconds to check if the monitor is in the
ON mode.
• Check if the power cord is properly
connected to the monitor and the power
outlet.
The power LED flashes blue and there is no
screen image
• Check if the monitor and the computer are
in the ON mode.
• Make sure the signal cable is properly
connected the monitor and the
computer.
• Inspect the signal cable and make sure
none of the pins are bent.
• Connect the computer with another
available monitor to check if the computer
is properly working.
Screen image is too light or dark • Adjust the Contrast and Brightness
settings via OSD.
Your device fails to connect to the monitor
wirelessly
• Update your device to the latest operating
system.
• Change the Wi-Fi Setting to 2.4G via
OSD.
Screen image is too light or dark • Adjust the Contrast and Brightness
settings via OSD.
Screen image bounces or a wave pattern is
present in the image
• Make sure the HDMI/USB Type-C cable is
properly connected to the monitor and the
computer.
• Move electrical devices that may cause
electrical interference.
Screen image has color defects (white does
not look white)
• Inspect the HDMI/USB Type-C cable
and make sure that none of the pins are
bent.
The monitor screen is frozen • Connect to the ASUS adapter and press
the button for 10-15 seconds to restart
the monitor.
3-13ASUS Wireless Portable Monitor MB16A
Problem Possible Solution
The monitor automatically turns off • The monitor automatically turns off when
the battery power is zero. Please connect
to the ASUS adapter and check if the
battery is low; if so, charge the battery
before using it.
• The monitor automatically turns off after
there is no wireless source connection
for more than 6 minutes to save power
consumption.
• The monitor automatically turns off in
saving mode for more than 60 minutes to
save power consumption without external
power supply.
Poor wireless performance with Windows
computer
1. Disconnect your computer from all Wi-Fi
access points.
2. Re-connect your computer to the
monitor.
3. Re-connect your compter to a Wi-Fi access
point.
3-14 Chapter 3: OSD (On-Screen Display) menu
3.5 Supportedoperatingmodes
Resolution
Frequency
Horizontal
Frequency (KHz)
Vertical Frequency
(Hz)
Pixel
(MHz)
640x480 31.47(N) 59.94(N) 25.18
800x600 37.88(P) 60.32(P) 40
1024x768 48.36(N) 60.00(N) 65
1280x720 45.00(P) 60.00(N) 74.25
1280x960 60.00(P) 60.00(N) 108
1280x1024 63.98(P) 60.02(P) 108
1440x900 55.94(N) 59.89(P) 106.5
1680x1050 65.29(N) 60.00(P) 146.25
1920x1080 67.5(P) 60.00(P) 148.5
* “P” / “N” stands for “Positive” / “Negative” polarity of incoming H-sync/V-sync (input timing).