Table of Contents
- Contents
- Notices
- TCO certified
- Safety information
- Care & Cleaning
- Takeback Services
- Chapter 1: Product introduction
- 1.1 Welcome!
- 1.2 Package contents
- 1.3 Monitor introduction
- Chapter 2: Setup
- 2.1 Assembling the monitor arm/base
- 2.2 Detaching the arm/base (for VESA wall mount)
- 2.3 Adjusting the monitor
- 2.4 Connecting the cables
- 2.5 Turning on the monitor
- Chapter 3: General instructions
- 3.1 OSD (On-Screen Display) menu
- 3.2 Specifications summary
- 3.3 Outline dimensions
- 3.4 Troubleshooting (FAQ)
- 3.5 Supported operating modes
ASUS PA248QV User Manual
Displayed below is the user manual for PA248QV by ASUS which is a product in the Computer Monitors category. This manual has pages.
Related Manuals
PA248QV
Series LCD Monitor
User Guide
ii
First Edition
March 2020
Copyright © 2020 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless
such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM
ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN
THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the
owners’ benet, without intent to infringe.
iii
Contents
1.3.1 Front view ....................................................................... 1-2
1.3.2 Back view ........................................................................ 1-4
3.1.1 How to recongure .......................................................... 3-1
3.1.2 OSD function introduction ............................................... 3-2
iv
Notices
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modications
to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
ENERGY STAR is a joint program of the U.S. Environmental
Protection Agency and the U.S. Department of Energy helping us all
save money and protect the environment through energy efcient
products and practices.
All ASUS products with the ENERGY STAR logo comply with the ENERGY
STAR standard, and the power management feature is enabled by default. The
monitor and computer are automatically set to sleep after 10 and 30 minutes of
user inactivity. To wake your computer, click the mouse or press any key on the
keyboard. Please visit http://www.energystar.gov/powermanagement for detail
information on power management and its benets to the environment. In addition,
please visit http://www.energystar.gov for detail information on the ENERGY STAR
joint program.
v
NOTE: Energy Star is NOT supported on FreeDOS and Linux-based operating
system.
This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
This Class B digital apparatus meets all requirements of the Canadian
Interference - Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Réglement sur le matériel brouiller du Canada.
vi
TCO certied
A third-party certification according to ISO 14024
Say hello
to a more sustainable product
IT products are associated with a wide range of sustainability risks
throughout their life cycle. Human rights violations are common in the
factories. Harmful substances are used both in products and their
manufacture. Products can often have a short lifespan because of poor
ergonomics, low quality and when they are not able to be repaired or
upgraded.
This product is a better choice. It meets all the criteria in TCO Certified,
the world’s most comprehensive sustainability certification for IT
products. Thank you for making a responsible product choice, that help
drive progress towards a more sustainable future!
Criteria in TCO Certified have a life-cycle perspective and balance
environmental and social responsibility. Conformity is verified by
independent and approved verifiers that specialize in IT products, social
responsibility or other sustainability issues. Verification is done both
before and after the certificate is issued, covering the entire validity
period. The process also includes ensuring that corrective actions are
implemented in all cases of factory non-conformities. And last but not
least, to make sure that the certification and independent verification is
accurate, both TCO Certified and the verifiers are reviewed regularly.
Want to know more?
Read information about TCO Certified, full criteria documents, news and
updates at tcocertified.com. On the website you’ll also find our Product
Finder, which presents a complete, searchable listing of certified
products.
Toward sustainable IT products
vii
Safety information
• Before setting up the monitor, carefully read all the documentation that came
with the package.
• To prevent re or shock hazard, never expose the monitor to rain or moisture.
• Never try to open the monitor cabinet. The dangerous high voltages inside the
monitor may result in serious physical injury.
• If the power supply is broken, do not try to x it by yourself. Contact a qualied
service technician or your retailer.
• Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
• Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or over a
radiator or heat source unless proper ventilation is provided.
• The monitor should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.
• Use the appropriate power plug which complies with your local power standard.
• Do not overload power strips and extention cords. Overloading can result in re
or electric shock.
• Avoid dust, humidity, and temperature extremes. Do not place the monitor in
any area where it may become wet. Place the monitor on a stable surface.
• Unplug the unit during a lightning storm or if it will not be used for a long period
of time. This will protect the monitor from damage due to power surges.
• Never push objects or spill liquid of any kind into the slots on the monitor
cabinet.
• To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate congured receptacles marked between
100-240V AC.
• If you encounter technical problems with the monitor, contact a qualied
service technician or your retailer.
• Adjustment of the volume control as well as the equalizer to other settings
than the center position may increase the ear-/headphones output voltage and
therefore the sound pressure level.
This symbol of the crossed out wheeled bin indicates that the product (electrical,
electronic equipment, and mercury-containing button cell battery) should not
be placed in municipal waste. Please check local regulations for disposal of
electronic products.
viii
Care & Cleaning
• Before you lift or reposition your monitor, it is better to disconnect the cables
and power cord. Follow the correct lifting techniques when positioning the
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.
Do not lift the display by the stand or the cord.
• Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed
with a cloth dampened with mild cleaner.
• Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended
for use with the monitor. Never spray cleaner directly on the screen, as it may
drip inside the monitor and cause an electric shock.
• You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
• When the same image is displayed for hours, an afterimage of the previous
screen may remain after switching the image. The screen will recover slowly or
you can turn off the Power Switch for hours.
• When the screen becomes black or ashes, or cannot work anymore, contact
your dealer or service center to x it. Do not repair the screen by yourself!
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying
to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
ix
Refer to the following sources for additional information and for product and
software updates.
The ASUS websites worldwide provide updated information on ASUS
hardware and software products. Refer to http://www.asus.com
Your product package may include optional documentation that may have
been added by your dealer. These documents are not part of the standard
package.
Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest
standards for protecting our environment. We believe in providing solutions for
our customers to be able to responsibly recycle our products, batteries and other
components as well as the packaging materials.
Please go to http://csr.asus.com/english/Takeback.htm for detail recycling
information in different region.
1-1ASUS PA248QV Series LCD Monitor
1.1 Welcome!
Thank you for purchasing the ASUS® LCD monitor!
The latest widescreen LCD monitor from ASUS provides a broader, brighter and
crystal-clear display, plus a host of features that enhance your viewing experience.
With these features, you can enjoy the convenience and delightful visual
experience that the monitor brings to you!
1.2 Package contents
Check your package for the following items:
LCD monitor
Monitor base
Quick start guide
Warranty card
Power cord
HDMI cable (optional)
DisplayPort cable (optional)
VGA cable (optional)
USB B to A cable (optional)
Audio cable (optional)
Color Calibration Testing Report
ProArt welcome card
If any of the above items is damaged or missing, contact your retailer
immediately.
1-2 Chapter 1: Product introduction
1.3 Monitor introduction
6 5 4 3 2 1
1. Power button/power indicator
• Turns the monitor on/off.
• The color denition of the power indicator is as the below table.
White On
Amber Standby mode
Off Off
2. Menu button:
• Press this button to display the OSD menu when the OSD is off.
• Enters the OSD menu.
• Toggles the Key Lock function between on and off with a long press for
5 seconds.
3. Close button:
• Press this button to display the OSD menu when the OSD is off.
• Exits the OSD menu.
4. QuickFit button:
• Press this button to display the OSD menu when the OSD is off.
• This is a hotkey to activate the QuickFit function designed for alignment.
• The QuickFit function contains pages of common grid patterns, paper
sizes, and photo sizes. (Please refer to 3.1.2 OSD function introduction).
1-3ASUS PA248QV Series LCD Monitor
5. Shortcut
• Press this button to display the OSD menu when the OSD is off.
• Default: Brightness hotkey
• To change the hotkey function, go to the Shortcut > Shortcut 1 menu.
6. Shortcut
• Press this button to display the OSD menu when the OSD is off.
• Default: Blue light lter hotkey
• To change the hotkey function, go to the Shortcut > Shortcut 2 menu.
1-4 Chapter 1: Product introduction
11
123456789
10
.
. Press the switch to turn on/off power.
. This port connects the power cord.
. This port connects PC audio source by the bundled audio
cable.
. This port is only available when an HDMI/DisplayPort cable
is connected.
. This port is for connection with a DisplayPort compatible
device.
This port is for connection with an HDMI compatible device.
. This 15-pin port is for PC VGA connection.
. This port is for connection with a USB upstream cable. The
connection enables the USB ports on the monitor.
. These ports are for connection with USB devices, such as
USB keyboard/mouse, USB ash drive, etc.
. These ports are for connection with USB devices, such as
USB keyboard/mouse, USB ash drive, etc.
Port with icon is BC1.2 compliant.
2-1ASUS PA248QV Series LCD Monitor
2.1 Assembling the monitor arm/base
To assemble the monitor base:
1. Have the front of the monitor face down on a table.
2. Attach the base into the arm, making sure the tab on the arm ts into the
groove on the base.
3. Fix the base to the arm by fastening the bundled screw.
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
Base screw size: M6 x 16.2 mm.
2.2 Detaching the arm/base
(for VESA wall mount)
The detachable arm/base of this monitor is specially designed for VESA wall
mount.
To detach the arm/base:
1. Have the front of the monitor face down on a table.
2. Press the release button, and then detach the arm/base from the monitor
(Figure 2).
1
2
(Figure 1) (Figure 2)
2-2 Chapter 2: Setup
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
• The VESA wall mount kit (100 x 100 mm) is purchased separately.
• Use only the UL Listed Wall Mount Bracket with minimum weight/load
22.7kg (Screw size: M4 x 10 mm)
2.3 Adjusting the monitor
• For optimal viewing, we recommend that you look at the full face of the
monitor, then adjust the monitor to the angle that is most comfortable for you.
• Hold the stand to prevent the monitor from falling when you change its angle.
• You can adjust the monitor’s angle from +35˚ to -5˚and it allows 90˚ swivel
adjustment from either left or right. You can also adjust the monitor’s height
within +/- 130 mm.
90°
0°
90°
-5° ~ +35°
130mm
(Swivel) (Height adjustment)(Tilt)
1. Lift the monitor to the highest position.
2. Tilt the monitor to its maximum angle.
3. Pivot the monitor clockwise/counterclockwise to the angle you need.
2-3ASUS PA248QV Series LCD Monitor
90°
90°
It is normal that the monitor slightly shakes while you adjust the viewing angle.
2.4 Connecting the cables
Connect the cables as the following instructions:
: Connect one end of the power cord securely to
the monitor’s AC input port, the other end to a power outlet.
:
a. Plug one end of the VGA/DisplayPort/HDMI cable to the monitor’s VGA/
DisplayPort/HDMI jack.
b. Connect the other end of the VGA/DisplayPort/HDMI cable to your
computer's VGA /DisplayPort/HDMI jack.
c. Tighten the two screws to secure the VGA connector.
connect one end of the audio cable to the
monitor’s Audio-in port, the other end to the computer’s audio-out port.
connect the end with plug type to the monitor’s
earphone jack when an HDMI/DisplayPort signal is fed.
:
»Upstream: Use the supplied USB Type-B to Type-A cable. Make sure
your computer is installed with the latest Windows 7/Windows 8.1/
Windows 10 operating system. That will enable the USB ports on the
monitor to work.
2-4 Chapter 2: Setup
»Downstream: Plug the USB Type-A cable of your device to the monitor's
USB Type-A jack.
When these cables are connected, you can choose the desired signal
from the Input Select item in the OSD menu.
2.5 Turning on the monitor
Press the power button . See page 1-2 for the location of the power button. The
power indicator lights up in white to show that the monitor is ON.
3-1ASUS PA248QV Series LCD Monitor
3.1 OSD (On-Screen Display) menu
3.1.1 How to reconfigure
Standard Mode
sRGB Mode
Rec 709 Mode
Scenery Mode
Reading Mode
Darkroom Mode
Rapid Rendering Mode
more
ProArt Preset ASUS PA248QV
Standard Mode DisplayPort 1920 x 1200@ 60Hz
1. Press any button (except the Power button) to display the OSD menu.
2. Press the Menu button to activate the OSD menu.
3. Press the buttons as indicated on the screen to navigate through the
functions. Highlight the desired function and press to activate it. If the
function selected has a sub-menu, press and again to navigate
through the sub-menu functions. Highlight the desired sub-menu function and
press to activate it.
4. Press and to change the settings of the selected function.
5. To exit and save the OSD menu, press or repeatedly until the OSD menu
disappears. To adjust other functions, repeat steps 1-4.
3-2 Chapter 3: OSD (On-Screen Display) menu
3.1.2 OSD function introduction
This function contains 9 sub-functions you can select for your preference.
Each mode has the Reset selection, allowing you to maintain your setting or
return to the preset mode.
Standard Mode
sRGB Mode
Rec 709 Mode
Scenery Mode
Reading Mode
Darkroom Mode
Rapid Rendering Mode
more
ProArt Preset ASUS PA248QV
Standard Mode DisplayPort 1920 x 1200@ 60Hz
: Best choice for document editing.
: Compatible with sRGB color space, sRGB mode is the best
choice for document editing.
sRGB Mode meets Energy Star® requirements.
: Compatible with Rec. 709 color space.
Best choice for scenery photo display.
: This is the best choice for book reading.
: This is the best choice for a weak ambient light
environment.
: Simulates display as high refresh rate
performance to generate different backlight frequencies.
Rapid Rendering Mode can only be activated at 75Hz.
To activate this function, you need to do the following: turn off Adaptive-Sync.
Brightness, Blue Light Filter, ASCR, Trace Free cannot be adjusted when using
this function.
: Allows you to make color adjustments in the
Advanced Setting.
3-3ASUS PA248QV Series LCD Monitor
Below table shows the default congurations for each ProArt Preset mode:
Function Standard
Mode
sRGB
Mode
Rec. 709
Mode
Scenery
Mode
Reading
Mode
Darkroom
Mode
Rapid
Rendering
Mode
User Mode
1/User
Mode 2
Color Engine Off Off Off Off Off Off Off Off
Color Temp. 6500K Fixed
6500K 6500K 6500K Disable 6500K 6500K 6500K
Brightness 50 100 nits 100 nits 100 Enable (9) Enable (2) 50 50
Contrast 80 Fixed
80 80 80 Disable
(80) 80 80 80
ASCR Disable Disable Disable Off Disable Off Disable Disable
Sharpness Enable (0) Enable (0) Enable (0) Enable (0) Enable (0) Enable (0) Enable (0) Enable (0)
Saturation Middle
(50) Disable Middle
(50)
Middle
(50) Disable Middle
(50)
Middle
(50)
Middle
(50)
Hue Middle
(50) Disable Middle
(50)
Middle
(50) Disable Middle
(50)
Middle
(50)
Middle
(50)
Advanced
Setting
Enable
(Default) Disable Enable
(Default)
Enable
(Default)
Enable
(Default)
Enable
(Default)
Enable
(Default)
Enable
(Default)
Gamma Enable
(2.2)
Fixed
2.2
Enable
(2.4) Disable Enable
(2.2)
Enable
(2.2)
Enable
(2.2)
Enable
(2.2)
VividPixel 0 0 0 0 0 0 0 0
In this function, you can adjust the blue light filter level.
ASUS PA248QV
Standard Mode DisplayPort 1920 x 1200@ 60Hz
Level 0
Level 1
Level 2
Level 3
Level 4
Blue Light Filter
No change.
The higher the level, the less blue light is scattered.
When Blue Light Filter is activated,the default settings of Standard Mode
will be automatically imported. Between Level 1 to Level 3, the Brightness
function is user-configurable. Level 4 is optimized setting. It is compliance
with TUV Low Blue Light Certification. The Brightness function is not user-
configurable. Enabling this function automatically turns off ECO Mode.
Please refer to the following to alleviate eye strains:
3-4 Chapter 3: OSD (On-Screen Display) menu
• Users should take some time away from the display if working for long
hours. It is advised to take short breaks (at least 5 mins) after around 1
hour of continuous working at the computer. Taking short and frequent
breaks is more effective than a single longer break.
• To minimize eye strain and dryness in your eyes, users should rest the eye
periodically by focusing on objects that are far away.
• Eye exercises can help to reduces eye strain. Repeat these exercises
often. If eye strain continues please consult a physician. Eye exercises: (1)
Repeating look up and down (2) Slowly roll your eyes (3) Move your eyes
diagonal.
• High energy blue light may lead to eye strain and AMD (Age-Related
Macular Degeneration). Blue light Filter to reduce 70% (max.) harmful blue
light to avoiding CVS (Computer Vision Syndrome).
Set a desired color setting from this menu.
ASUS PA248QV
Standard Mode DisplayPort 1920 x 1200@ 60Hz
Brightness
Contrast
Saturation
Hue
Color Temp.
Gamma
Black Level
more
ProArt Palette
: The adjusting range is from 0 to 100.
: The adjusting range is from 0 to 100.
: The adjusting range is from 0 to 100.
: Shifts the image color between green and purple.
: Contains 4 modes including 9300K, 6500K, 5500K and
5000K.
: Allows you to set the color mode to 2.6, 2.4, 2.2, 2.0 or 1.8
(Mac).
: To adjust the initialized 1st signal level of darkest gray level.
:
* Six-axis Hue adjustment.
* Six-axis Saturation adjustment.
* Adjusts the gain levels for R, G, B.
3-5ASUS PA248QV Series LCD Monitor
* Adjusts the black level offset values for R, G, B.
:
* Current mode color reset:
Resets the color settings of current color mode to the factory
default value.
* All modes color reset:
Resets the color settings of all color modes to the factory default
value.
Set the image related setting from this menu.
ASUS PA248QV
Standard Mode DisplayPort 1920 x 1200@ 60Hz
Sharpness
Trace Free
Aspect Control
VividPixel
ASCR
Position
Focus
more
Image
: The adjusting range is from 0 to 100.
: Adjusts the response time of the monitor.
: Adjusts the aspect ratio to full, 4:3, or OverScan.
4:3 is only available when input source is in 4:3 format. OverScan is
only available for the HDMI input source.
: Enhances the outline of the displayed picture and generates
high-quality images on screen.
: Turns on/off the ASCR (ASUS Smart Contrast Ratio) function.
: adjusts the horizontal position
(H-Position) and the vertical position (V-Position) of the image. The
adjusting range is from 0 to 100.
: reduces Horizonal-line noise
and Vertical-line noise of the image by adjusting (Phase) and (Clock)
separately. The adjusting range is from 0 to 100.
3-6 Chapter 3: OSD (On-Screen Display) menu
• Phase adjusts the phase of the pixel clock signal. With a wrong phase
adjustment, the screen shows horizontal disturbances.
• Clock (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the image is not proportional.
: Automatically adjusts the image to its optimized position,
clock, and phase (for VGA mode only).
You can adjust Volume, Mute and Source from this menu.
ASUS PA248QV
Standard Mode DisplayPort 1920 x 1200@ 60Hz
Volume
Mute
Source
Sound
: the adjusting range is from 0 to 100.
: toggles the monitor sound between on and off.
: decides the monitor sound comes from which source.
In this function, you can select your desired input source.
ASUS PA248QV
Standard Mode DisplayPort 1920 x 1200@ 60Hz
VGA
HDMI
DisplayPort
Input Select
3-7ASUS PA248QV Series LCD Monitor
Allows you to adjust the system.
ASUS PA248QV
Standard Mode DisplayPort 1920 x 1200@ 60Hz
Adaptive-Sync
USB Charging
OSD Setup
QuickFit
Language
DisplayPort Stream
Key Lock
more
System Setup
(DisplayPort/HDMI only): Allows an Adaptive-Sync
supported* graphics source to dynamically adjust display refresh rate
based on typical content frame rates for power efcient, virtually stutter
free and low-latency display update.
* Adaptive-Sync can only be activated within 48Hz ~ 75Hz.
* For supported GPUs, minimum PC system and driver requirements, please
contact the GPU manufactures.
To activate this function, you need to do the following: set DisplayPort Stream to
DisplayPort 1.2.
:
* “On During Standby” allows the USB downstream ports to charge
external devices when the monitor is turned on or in standby
mode.
* “Off During Standby” allows the USB downstream ports to charge
external devices only when the monitor is turned on.
Only USB downstream port BC1.2 is able to charge without upstream cable
connected.
:
* Adjusts the OSD timeout from 10 to 120 seconds.
* Enables or disables the DDC/CI function.
* Adjusts the OSD background from opaque to transparent.
* Adjusts the OSD rotation.
: Allows users to have a preview of the document or photo layout
directly on screen without printing test copies.
3-8 Chapter 3: OSD (On-Screen Display) menu
* Ruler: This pattern presents physical ruler on top and left side. You
can press the Return button for longer than 3 seconds to switch
the measurements between metric and imperial.
5
5
10
10
15
15 20 25 30
* Alignment: Facilitates designers and users to organize content and
layout on one page and achieve a consistent look and feel.
Alignment Grid
* A4: Provides users to view their documents in real size on the
screen.
A4
* B5: Provides users to view their documents in real size on the
screen.
B5
: There are 21 languages for your selection, including English,
French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech,
Croatian, Polish, Romanian, Hungarian, Turkish, Simplied Chinese,
Traditional Chinese, Japanese, Korean, Thai, Indonesian, Persian.
3-9ASUS PA248QV Series LCD Monitor
: Compatibility with graphic card. Select DisplayPort
1.1 or DisplayPort 1.2 by graphic card DP version.
: To disable all function keys. Press the second button from the
top over five seconds to cancel the key lock function.
: Turns the power LED indicator on/off.
: Shows the monitor information.
: “Yes” allows you to restore the default settings.
Defines the functions for Shortcut 1 and 2 buttons.
ASUS PA248QV
Standard Mode DisplayPort 1920 x 1200@ 60Hz
Shortcut 1
Shortcut 2
Shortcut
: Selects a function for Shortcut 1 and 2 buttons.
When a certain function is selected or activated, your shortcut key may
not support. Available function choices for shortcut: Blue Light Filter,
Brightness, Contrast, Color Temp., QuickFit, User Mode 1, User Mode 2.
3-10 Chapter 3: OSD (On-Screen Display) menu
3.2 Specications summary
TFT LCD
24” (16:10, 61.13 cm) wide screen
1920 x 1200
0.270 mm x 0.270 mm
300 cd/m2
1000:1
100,000,000:1 (with ASCR on)
178˚/178˚
16.7 M
< 5 ms (grey to grey)
9 color preset modes
Yes
4 color temperatures
D-sub
DisplayPort v1.2, HDMI v1.4
No
Yes
Yes
2 W x 2 Stereo, RMS
Upstream x 1, Downstream x 4
Black
White (On)/Amber (Standby)
+35˚~ -5˚
+90˚~ -90˚
+90˚~ -90˚
130 mm
Yes
AC: 100~240V
Power On: < 15 W** (Typ.), Standby: < 0.5 W (Typ.),
Power Off: 0 W (Switch off)
0˚C~40˚C
-20˚C~+60˚C
533 x 360 x 40 mm
533 x 505 x 211 mm (highest),
533 x 375 x 211 mm (lowest),
649 x 474 x 192 mm (package)
6.1 kg (Net); 3.9 kg (without stand); 8.3 kg (Gross)
21 languages (English, French, German, Italian,
Spanish, Dutch, Portuguese, Russian, Czech,
Croatian, Polish, Romanian, Hungarian, Turkish,
Simplied Chinese, Traditional Chinese, Japanese,
Korean, Thai, Indonesian, Persian)
3-11ASUS PA248QV Series LCD Monitor
Quick start guide, warranty card, power cord, Color
Calibration Testing Report, ProArt welcome card
HDMI cable (optional), DisplayPort cable (optional),
VGA cable (optional), USB B to A cable (optional),
Audio cable (optional)
UL/cUL, FCC, ICES-3, CB, CE, ErP, WEEE, TUV-GS,
TUV-Ergo, ISO 9241-307, UkrSEPRO, CU, CCC,
CEL, BSMI, RCM, MEPS, VCCI, PSE, PC Recycle,
J-MOSS, KC, KCC, e-Standby, Energy Star
®
8.0, TCO,
RoHs, Windows 7/8.1/10 WHQL, Flicker Free, Low
Blue Light
3-12 Chapter 3: OSD (On-Screen Display) menu
3.3 Outlinedimensions
259.2
7.25
7.25
7.25
324
359.3
503.65
323.73
344.32
47.095
17.7
211.34
262.74
144.35
162
518.4
28.05
Pivot : +/- 90 Degree
Tilt : -35~5 Degree
Swivel : +/- 90 Degree
Lift : 130mm
5°
35°
68.74
52.91
194.69
90°
90°
90°
90°
100
3-13ASUS PA248QV Series LCD Monitor
3.4 Troubleshooting (FAQ)
Power LED is not ON • Press the button to check if the monitor
is in the ON mode.
• Check if the power cord is properly
connected to the monitor and the power
outlet.
• Check if the power switch is ON.
The power LED lights amber and there is
no screen image
• Check if the monitor and the computer are
in the ON mode.
• Make sure the signal cable is properly
connected the monitor and the computer.
• Inspect the signal cable and make sure
none of the pins are bent.
• Connect the computer with another
available monitor to check if the computer
is properly working.
Screen image is too light or dark • Adjust the Contrast and Brightness
settings via OSD.
Screen image is not centered or sized
properly
• Adjust the H-Position or V-Position
settings via OSD.
Screen image bounces or a wave pattern is
present in the image
• Make sure the signal cable is properly
connected to the monitor and the
computer.
• Move electrical devices that may cause
electrical interference.
Screen image has color defects (white does
not look white)
• Inspect the signal cable and make sure
that none of the pins are bent.
• Perform All Reset via OSD.
• Adjust the R/G/B color settings or select
the Color Temperature via OSD.
Screen image is blurry or fuzzy • Adjust the Phase and Clock settings via
OSD.
No sound or sound is low • Ensure that the HDMI/DisplayPort cable is
properly connected to the monitor and the
computer.
• Adjust the volume settings of both your
monitor and HDMI/DisplayPort device.
• Ensure that the computer sound card
driver is properly installed and activated.
3-14 Chapter 3: OSD (On-Screen Display) menu
3.5 Supported operating modes
640x480 31.47(N) 59.94(N) 25.18
640x480 35.00(N) 66.66(N) 30.24
640x480* 37.87(N) 72.82(N) 31.5
640x480* 37.5(N) 75.00(N) 31.5
720x400* 31.47(N) 70.08(P) 28.32
800x600 35.16(P) 56.25(P) 36
800x600 37.88(P) 60.32(P) 40
800x600* 46.86(P) 75.00(P) 49.5
832x624* 49.72(P/N) 74.55(P/N) 57.28
1024x768 48.36(N) 60.00(N) 65
1024x768 56.476(N) 70.069(N) 75
1024x768* 60.02(N) 75.00(N) 78.75
1152x864* 67.5(P/N) 75.00(P/N) 108
1280x720 45.00(P) 60.00(N) 74.25
1280x768 47.78(P) 60.00(N) 79.5
1280x800 49.7(P) 60.00(N) 83.5
1280x960 60.00(P) 60.00(N) 108
1280x1024 63.98(P) 60.02(P) 108
1280x1024* 79.98(P) 75.02(P) 135
1440x900 55.94(N) 59.89(P) 106.5
1600x1200 75.00(P) 60.00(P) 162
1680x1050 65.29(N) 60.00(P) 146.25
1920x1080 67.5(P) 60.00(P) 148.5
1920x1200
(Reduced Blanking) 74.038(P) 59.95(N) 154
1920x1200*
(HDMI/DP only) 94.04(N) 74.94(P) 245.25
3-15ASUS PA248QV Series LCD Monitor
480p 720 x 480 31.469 60 27
720p60 1280 x 720 45 60 74.25
576p 720 x 576 31.25 50 27
720p50 1280 x 720 37.5 50 74.25
1080p60 1920 x 1080 67.5 60 148.5
1080p50 1920 x 1080 56.25 50 148.5