1 Getting to know your wireless router
2 Getting started
3 Configuring the General settings
4 Configuring the Advanced Settings
5 Utilities
6 Troubleshooting
- 6.1 Basic Troubleshooting
- 6.2 Frequently Asked Questions (FAQs)
Appendices

ASUS RT-AC1900P User Manual

Displayed below is the user manual for RT-AC1900P by ASUS which is a product in the Wireless Routers category. This manual has pages.

Related Manuals

ASUS ASUS Rampage IV GENE Manual

ASUS ASUS X99-DELUXE II Manual

ASUS ASUS MCI-10G/X550-2T Manual

ASUS UX435EAL-KC096T Manual

ASUS PN62S-B3519ZD Manual

ASUS VE228H Manual

ASUS RS700DA-E6/PS4 Manual

ASUS PCE-N15 Manual

User Guide

RT-AC1900P Dual Band

3x3 Wireless-AC 1900 Gigabit Router

1900P

No part of this manual, including the products and software described

in it, may be reproduced, transmitted, transcribed, stored in a retrieval

system, or translated into any language in any form or by any means, except

documentation kept by the purchaser for backup purposes, without the

express written permission of ASUSTeK Computer Inc. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired,

modiﬁed or altered, unless such repair, modiﬁcation of alteration is authorized

in writing by ASUS; or (2) the serial number of the product is defaced or

missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND,

EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED

WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS,

EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL,

OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,

LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS

AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR

PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE

FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE

AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A

COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY

FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL,

INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be

registered trademarks or copyrights of their respective companies, and are used

only for identiﬁcation or explanation and to the owners’ beneﬁt, without intent

to infringe.

E11212

First Edition

December 2015

Table of contents

1 Getting to know your wireless router 6

1.1 Welcome! ........................................................................................6

1.2 Package contents .........................................................................6

1.3 Your wireless router .....................................................................7

1.4 Positioning your router ..............................................................9

1.5 Setup Requirements ................................................................ 10

1.6 Router Setup ............................................................................... 11

1.6.1 Wired connection ..................................................................11

1.6.2 Wireless connection ............................................................. 12

2 Getting started 14

2.1 Logging into the Web GUI ..................................................... 14

2.2 Quick Internet Setup (QIS) with Auto-detection ........... 15

2.3 Connecting to your wireless network ................................ 19

3 Conﬁguring the General settings 20

3.1 Using the Network Map ......................................................... 20

3.1.1 Setting up the wireless security settings ......................21

3.1.2 Managing your network clients ....................................... 22

3.1.3 Monitoring your USB device .............................................23

3.2 Creating a Guest Network ...................................................... 26

3.3 Using the Traﬃc Manager ...................................................... 28

3.3.1 Managing QoS (Quality of Service) Bandwidth..........28

3.3.2 Monitoring Traﬃc .................................................................31

3.4 Setting up Parental Control ................................................... 32

3.5 Using the USB Application ..................................................... 33

3.5.1 Using AiDisk ............................................................................... 33

3.5.2 Using Servers Center ............................................................35

3.5.3 3G/4G ........................................................................................41

Table of contents

3.6 Using AiCloud ............................................................................. 43

3.6.1 Cloud Disk ................................................................................44

3.6.2 Smart Access ........................................................................... 46

3.6.3 Smart Sync ............................................................................... 47

4 Conﬁguring the Advanced Settings 48

4.1 Wireless ......................................................................................... 48

4.1.1 General ......................................................................................48

4.1.2 WPS ............................................................................................51

4.1.3 Bridge ........................................................................................53

4.1.4 Wireless MAC Filter ...............................................................55

4.1.5 RADIUS Setting ......................................................................56

4.1.6 Professional .............................................................................57

4.2 LAN ................................................................................................. 59

4.2.1 LAN IP ........................................................................................59

4.2.2 DHCP Server ............................................................................60

4.2.3 Route .........................................................................................62

4.2.4 IPTV ............................................................................................... 63

4.3 WAN ............................................................................................... 64

4.3.1 Internet Connection .............................................................64

4.3.2 Port Trigger ..............................................................................67

4.3.3 Virtual Server/Port Forwarding ........................................69

4.3.4 DMZ............................................................................................72

4.3.5 DDNS .........................................................................................73

4.3.6 NAT Passthrough ...................................................................74

4.4 IPv6 ................................................................................................. 75

4.5 VPN Server ................................................................................... 76

4.6 Firewall .......................................................................................... 77

4.6.1 General ......................................................................................77

4.6.2 URL Filter ..................................................................................77

4.6.3 Keyword ﬁlter .........................................................................78

Table of contents

4.6.4 Network Services Filter .......................................................79

4.7 Administration ........................................................................... 81

4.7.1 Operation Mode ....................................................................81

4.7.2 System ....................................................................................... 82

4.7.3 Firmware Upgrade ................................................................ 83

4.7.4 Restore/Save/Upload Setting ...........................................83

4.8 System Log .................................................................................. 84

5 Utilities 85

5.1 Device Discovery ....................................................................... 85

5.2 Firmware Restoration .............................................................. 86

5.3 Setting up your printer server .............................................. 87

5.3.1 ASUS EZ Printer Sharing .....................................................87

5.3.2 Using LPR to Share Printer .................................................91

5.4 Download Master ...................................................................... 96

5.4.1 Conﬁguring Bit Torrent download settings .................97

5.4.2 NZB settings ............................................................................ 98

6 Troubleshooting 99

6.1 Basic Troubleshooting ............................................................. 99

6.2 Frequently Asked Questions (FAQs) ................................102

Appendices 112

Notices .....................................................................................................112

ASUS Contact information ..................................................................126

Networks Global Hotline Information.............................................127

1 Getting to know your wireless

router

NOTES:

• Ifanyoftheitemsaredamagedormissing,contactASUSfor

technical inquiries and support, Refer to the ASUS Support Hotline

list at the back of this user manual.

• Keeptheoriginalpackagingmaterialincaseyouwouldneedfuture

warranty services such as repair or replacement.

RT-AC1900P Wireless Router Network cable (RJ-45)

Power adapter Quick Start Guide

Support CD (Manual)

1.1 Welcome!

Thank you for purchasing an ASUS RT-AC1900P Wireless Router!

The ultra-thin and stylish RT-AC1900P features a 2.4GHz and 5GHz

dual bands for an unmatched concurrent wireless HD streaming;

SMB server, UPnP AV server, and FTP server for 24/7 ﬁle sharing;

a capability to handle 300,000 sessions; and the ASUS Green

Network Technology, which provides up to 70% power-saving

solution.

1.2 Package contents

1.3 Your wireless router

1900P

LAN 1~4 LED

Oﬀ: No power or no physical connection.

On: Has physical connection to a local area network (LAN).

WAN (Internet) LED

Oﬀ: No power or no physical connection.

On: Has physical connection to a wide area network (WAN).

USB 3.0 / 2.0 LED

Oﬀ: No power or no physical connection.

On: Has physical connection to USB 3.0 / 2.0 devices.

2.4GHz LED / 5GHz LED

Oﬀ: No 2.4GHz or 5GHz signal.

On: Wireless system is ready.

Flashing: Transmitting or receiving data via wireless connection.

Power LED

Oﬀ: No power.

On: Device is ready.

Flashing slow: Rescue mode

Flashing quick: WPS is processing.

WPS button

This button launches the WPS Wizard.

NOTES:

• Useonlytheadapterthatcamewithyourpackage.Usingother

adapters may damage the device.

• Specifications:

DC Power adapter DC Output: +19V with max 1.75A current;

Operating

Temperature 0~40oCStorage 0~70oC

Operating Humidity 50~90% Storage 20~90%

WI-FI On/Oﬀ button

Press this button to turn on /off the Wi-Fi connection.

Power button

Press this button to power on or off the system.

Power (DC-IN) port

Insert the bundled AC adapter into this port and connect your router to a power source.

USB 3.0 / 2.0 ports

Insert USB 3.0 / 2.0 devices such as USB hard disks or USB flash drives into these ports.

Insert your iPad’s USB cable into one of these ports to charge your iPad.

WAN (Internet) port

Connect a network cable into this port to establish WAN connection.

LED On/Oﬀ button

Press this button to turn on/off the backlight LED on the panel.

LAN 1 ~ 4 ports

Connect network cables into these ports to establish LAN connection.

Reset button

This button resets or restores the system to its factory default settings.

Off

1.4 Positioning your router

For the best wireless signal transmission between the wireless

router and the network devices connected to it, ensure that you:

• Placethewirelessrouterinacentralizedareaforamaximum

wireless coverage for the network devices.

• Keepthedeviceawayfrommetalobstructionsandawayfrom

direct sunlight.

• Keepthedeviceawayfrom802.11gor20MHzonlyWi-Fi

devices, 2.4GHz computer peripherals, Bluetooth devices,

cordless phones, transformers, heavy-duty motors, fluorescent

lights, microwave ovens, refrigerators, and other industrial

equipment to prevent signal interference or loss.

• Alwaysupdatetothelatestfirmware.VisittheASUSwebsiteat

http://www.asus.com to get the latest firmware updates.

• Toensurethebestwirelesssignal,orientthethreedetachable

antennas as shown in the drawing below.

45°

90°

45°

1900P

1.5 Setup Requirements

To set up your wireless network, you need a computer that meets

the following system requirements:

• EthernetRJ-45(LAN)port(10Base-T/100Base-TX/

1000BaseTX)

• IEEE802.11a/b/g/n/acwirelesscapability

• AninstalledTCP/IPservice

• WebbrowsersuchasInternetExplorer,Firefox,Safari,or

Google Chrome

NOTES:

• Ifyourcomputerdoesnothavebuilt-inwirelesscapabilities,youmay

install an IEEE 802.11a/b/g/n/ac WLAN adapter to your computer to

connect to the network.

• Withitsdualbandtechnology,yourwirelessroutersupports2.4GHz

and 5GHz wireless signals simultaneously. This allows you to do

Internet-related activities such as Internet surfing or reading/writing

e-mail messages using the 2.4GHz band while simultaneously

streaming high-definition audio/video files such as movies or music

using the 5GHz band.

• SomeIEEE802.11ndevicesthatyouwanttoconnecttoyournetwork

may or may not support 5GHz band. Refer to the device's manual for

specifications.

• TheEthernetRJ-45cablesthatwillbeusedtoconnectthenetwork

devices should not exceed 100 meters.

1.6 Router Setup

IMPORTANT!

• Useawiredconnectionwhensettingupyourwirelessrouterto

avoid possible setup problems.

• BeforesettingupyourASUSwirelessrouter,dothefollowing:

 • Ifyouarereplacinganexistingrouter,disconnectitfromyour

network.

 • Disconnectthecables/wiresfromyourexistingmodemsetup.If

your modem has a backup battery, remove it as well.

 • Rebootyourcablemodemandcomputer(recommended).

1.6.1 Wired connection

NOTE: You can use either a straight-through cable or a crossover cable

for wired connection.

To set up your wireless router via wired connection:

1. Insert your wireless router’s AC adapter to the DC-IN port and

plug it to a power outlet.

RT-AC1900P

Computer

Wall Power Outlet

LAN

Modem

Power

WAN

2. Using the bundled network cable, connect your computer to

your wireless router’s LAN port.

IMPORTANT! Ensure that the LAN LED is blinking.

3 Using another network cable, connect your modem to your

wireless router’s WAN port.

4. Insert your modem’s AC adapter to the DC-IN port and plug it

to a power outlet.

1.6.2 Wireless connection

To set up your wireless router via wireless connection:

1. Insert your wireless router’s AC adapter to the DC-IN port and

plug it to a power outlet.

2 Using the bundled network cable, connect your modem to

your wireless router’s WAN port.

RT-AC1900P

Wall Power Outlet

Modem

Power

WAN

3. Insert your modem’s AC adapter to the DC-IN port and plug it

to a power outlet.

4. Install an IEEE 802.11a/b/g/n/ac WLAN adapter on your

computer.

NOTES:

• Fordetailsonconnectingtoawirelessnetwork,refertotheWLAN

adapter’s user manual.

• Tosetupthesecuritysettingsforyournetwork,refertothesection

Setting up the wireless security settings in Chapter 3 of this user

manual.

2 Getting started

2.1 Logging into the Web GUI

Your ASUS Wireless Router comes with an intuitive web graphical

user interface (GUI) that allows you to easily conﬁgure its various

features through a web browser such as Internet Explorer, Firefox,

Safari, or Google Chrome.

NOTE: The features may vary with diﬀerent ﬁrmware versions.

To log into the web GUI:

1. On your web browser, manually key in the wireless router’s

default IP address: 192.168.1.1 or enter http://router.asus.com.

2. On the login page, key in the default user name (admin) and

password (admin).

3. You can now use the Web GUI to conﬁgure various settings of

your ASUS Wireless Router.

NOTE: If you are logging into the Web GUI for the ﬁrst time, you will be

directed to the Quick Internet Setup (QIS) page automatically.

Navigation

panel

QIS

Top command buttons

Information

banner

middle

column

right column

2.2 Quick Internet Setup (QIS) with Auto-

detection

The Quick Internet Setup (QIS) function guides you in quickly

setting up your Internet connection.

NOTE: When setting the Internet connection for the ﬁrst time, press

the Reset button on your wireless router to reset it to its factory default

settings.

To use QIS with auto-detection:

1. Log into the Web GUI. The QIS page launches automatically.

The server 192.168.1.1 at RT-AC1900P requires a username and password.

NOTES:

• Bydefault,theloginusernameandpasswordforyourwireless

router's Web GUI is admin. For details on changing your wireless

router's login username and password, refer to section 4.7.2 System.

• Thewirelessrouter'sloginusernameandpasswordisdifferentfrom

the 2.4GHz/5GHz network name (SSID) and security key. The wireless

router's login username and password allows you to log into your

wireless router's Web GUI to configure your wireless router's settings.

The 2.4GHz/5GHz network name (SSID) and security key allows Wi-Fi

devices to log in and connect to your 2.4GHz/5GHz network.

2. The wireless router automatically detects if your ISP connection

type is Dynamic IP, PPPoE, PPTP, L2TP, and Static IP. Key in

the necessary information for your ISP connection type.

IMPORTANT! Obtain the necessary information from your ISP about

the Internet connection type.

for Automatic IP (DHCP)

for PPPoE, PPTP, and L2TP

for Static IP

NOTES:

• Theauto-detectionofyourISPconnectiontypetakesplacewhen

you configure the wireless router for the first time or when your

wireless router is reset to its default settings.

• IfQISfailedtodetectyourInternetconnectiontype,clickSkip to

manual setting and manually configure your connection settings.

3. Assign the wireless network name (SSID) and security key for

your 2.4GHz and 5 GHz wireless connection. Click Apply when

done.

4. Your Internet and wireless settings are displayed. Click Next to

continue.

5. Read the wireless network connection tutorial. When done,

click Finish.

2.3 Connecting to your wireless network

After setting up your wireless router via QIS, you can connect your

computer or other smart devices to your wireless network.

To connect to your network:

1. On your computer, click the network icon in the notiﬁcation

area to display the available wireless networks.

2. Select the wireless network that you want to connect to, then

click Connect.

3. You may need to key in the network security key for a secured

wireless network, then click OK.

4. Wait while your computer establishes connection to the

wireless network successfully. The connection status is

displayed and the network icon displays the connected

status.

NOTES:

• Refertothenextchaptersformoredetailsonconfiguringyour

wireless network's settings.

• Refertoyourdevice'susermanualformoredetailsonconnectingit

to your wireless network.

3 Conﬁguring the General

settings

3.1 Using the Network Map

Network Map allows you to conﬁgure your network’s security

settings, manage your network clients, and monitor your USB

device.

3.1.1 Setting up the wireless security settings

To protect your wireless network from unauthorized access, you

need to configure its security settings.

To set up the wireless security settings:

1. From the navigation panel, go to General > Network Map.

2. OntheNetworkMapscreenandunderSystem status, you can

configure the wireless security settings such as SSID, security

level, and encryption settings.

NOTE: You can set up diﬀerent wireless security settings for 2.4GHz and

5GHz bands.

2.4GHz security settings 5GHz security settings

3. On the Wireless name (SSID) field, key in a unique name for

your wireless network.

4. From the Security Level dropdown list, select the encryption

method for your wireless network.

IMPORTANT! The IEEE 802.11n/ac standard prohibits using High

Throughput with WEP or WPA-TKIP as the unicast cipher. If you use these

encryption methods, your data rate will drop to IEEE 802.11g 54Mbps

connection.

5. Keyinyoursecuritypasskey.

6. Click Apply when done.

3.1.2 Managing your network clients

To manage your network clients:

1. From the navigation panel, go to General > Network Map tab.

2. OntheNetworkMapscreen,selecttheClient Status icon to

display your network client’s information.

3. To block a client’s access to your network, select the client and

click block.

3.1.3 Monitoring your USB device

The ASUS Wireless Router provides two USB ports for connecting

USB devices or USB printer to allow you to share files and printer

with clients in your network.

NOTES:

• Tousethisfeature,youneedtoplugaUSBstoragedevice,suchasa

USB hard disk or USB flash drive, to the USB 3.0/2.0 ports on the rear

panel of your wireless router. Ensure that the USB storage device is

formatted and partitioned properly. Refer to the Plug-n-Share Disk

Support List at http://event.asus.com/networks/disksupport

• TheUSBportssupporttwoUSBdrivesoroneprinterandoneUSB

drive at the same time.

IMPORTANT! You ﬁrst need to create a share account and its

permission /access rights to allow other network clients to access the

USB device via an FTP site/third-party FTP client utility, Servers Center,

Samba, or AiCloud. For more details, refer to the section 3.5.Using the

USB Application and 3.6 Using AiCloud in this user manual.

To monitor your USB device:

1. From the navigation panel, go to General > Network Map.

2. OntheNetworkMapscreen,selecttheUSB Disk Status icon to

display your USB device’s information.

3. On the AiDisk Wizard field, click GO to set up an FTP server for

Internet file sharing.

NOTES:

• Formoredetails,refertothesection3.5.2 Using Servers Center in

this user manual.

• ThewirelessrouterworkswithmostUSBHDDs/Flashdisks(upto2TB

size) and supports read-write access for FAT16, FAT32, EXT2, EXT3,

and NTFS.

Safely removing the USB disk

IMPORTANT: Incorrect removal of the USB disk may cause data

corruption.

To safely remove the USB disk:

1. From the navigation panel, go to General > Network Map.

2. In the upper right corner, click > Eject USB disk. When

the USB disk is ejected successfully, the USB status shows

Unmounted.

3.2 Creating a Guest Network

The Guest Network provides temporary visitors with Internet

connectivity via access to separate SSIDs or networks without

providing access to your private network.

NOTE: RT-AC1900P supports up to six SSIDs (three 2.4GHz and three

5GHz SSIDs).

To create a guest network:

1. From the navigation panel, go to General > Guest Network.

2. On the Guest Network screen, select 2.4Ghz or 5Ghz frequency

band for the guest network that you want to create.

3. Click Enable.

4. To conﬁgure additional options, click Modify.

5. Click Yes on the Enable Guest Network screen.

6. Assign a wireless name for your temporary network on the

Network Name (SSID) ﬁeld.

7. Select an Authentication Method.

8. Select an Encryption method.

9. Specify the Access time or choose Limitless.

10. Select Disable or Enable on the Access Intranet item.

11. When done, click Apply.

3.3 Using the Traﬃc Manager

3.3.1 Managing QoS (Quality of Service) Bandwidth

Quality of Service (QoS) allows you to set the bandwidth priority

and manage network traﬃc.

To set up bandwidth priority:

1. From the navigation panel, go to General > Traﬃc Manager >

QoS tab.

2. Click ON to enable QoS. Fill in the upload and download

bandwidth ﬁelds.

NOTE: Get the bandwidth information from your ISP.

3. Click Save.

NOTE: The User Specify Rule List is for advanced settings. If you want

to prioritize speciﬁc network applications and network services, select

User-deﬁned QoS rules or User-deﬁned Priority from the drop-down

list on the upper-right corner.

4. On the user-deﬁned QoS rules page, there are four default

online service types – web surf, HTTPS and ﬁle transfers.

Select your preferred service, ﬁll in the Source IP or MAC,

Destination Port, Protocol, Transferred and Priority, then

click Apply. The information will be conﬁgured in the QoS rules

screen.

NOTES

• TofillinthesourceIPorMAC,youcan:

a) Enter a specific IP address, such as "192.168.122.1".

b) Enter IP addresses within one subnet or within the same IP

pool, such as “192.168.123.*”, or “192.168.*.*”

c) Enter all IP addresses as “*.*.*.*” or leave the field blank.

d) The format for the MAC address is six groups of two

hexadecimal digits, separated by colons (:), in transmission

order (e.g. 12:34:56:aa:bc:ef)

• Forsourceordestinationportrange,youcaneither:

a) Enter a specific port, such as “95”.

b) Enter ports within a range, such as “103:315”, “>100”, or

“<65535”.

• TheTransferred column contains information about the upstream

and downstream traffic (outgoing and incoming network traffic) for

one section. In this column, you can set the network traffic limit (in

KB) for a specific service to generate specific priorities for the service

assigned to a specific port. For example, if two network clients, PC

1 and PC 2, are both accessing the Internet (set at port 80), but PC 1

exceeds the network traffic limit due to some downloading tasks, PC

1 will have a lower priority. If you do not want to set the traffic limit,

leave it blank.

5. On the User-deﬁned Priority page, you can prioritize the

network applications or devices into ﬁve levels from the user-

deﬁned QoS rules’ dropdown list. Based on priority level, you

can use the following methods to send data packets:

• Changetheorderofupstreamnetworkpacketsthataresent

to the Internet.

• UnderUpload Bandwidth table, set Minimum Reserved

Bandwidth and Maximum Bandwidth Limit for multiple

network applications with diﬀerent priority levels. The

percentages indicate the upload bandwidth rates that are

available for speciﬁed network applications.

NOTES:

• Low-prioritypacketsaredisregardedtoensurethetransmissionof

high-priority packets.

• UnderDownload Bandwidth table, set Maximum Bandwidth

Limit for multiple network applications in corresponding order.

The higher priority upstream packet will cause the higher priority

downstream packet.

• Iftherearenopacketsbeingsentfromhigh-priorityapplications,the

full transmission rate of the Internet connection is available for low-

priority packets.

6. Set the highest priority packet. To ensure a smooth online

gaming experience, you can set ACK, SYN, and ICMP as the

highest priority packet.

NOTE: Ensure to enable QoS ﬁrst and set up the upload and download

rate limits.

3.3.2 Monitoring Traﬃc

The traﬃc monitor function allows you to access the bandwidth

usage and speed of your Internet, wired, and wireless networks. It

allows you to monitor network traﬃc even on a daily basis.

NOTE: Packets from the Internet are evenly transmitted to the wired

and wireless devices.

3.4 Setting up Parental Control

Parental Control allows you to control the Internet access time.

Users can set the time limit for a client’s network usage.

To use the parental control function:

1. From the navigation panel, go to General > Parental control.

2. Click ON to enable Parental Control.

3. Select the client whose network usage you want to control.

You may also key in the client’s MAC address in the Client MAC

Address column.

NOTE: Ensure that the client name does not contain special characters

or spaces as this may cause the router to function abnormally.

4. Click or to add or delete the client’s proﬁle.

5. Set up the allowed time limit in Time Management map. Drag

and drop a desired time zone to allow client’s network usage.

6. Click OK.

7. Click Apply to save the settings.

3.5 Using the USB Application

The USB Applications function provides AiDisk, Servers Center,

Network Printer Server and Download Master submenus.

IMPORTANT! To use the server functions, you need to insert a USB

storage device, such as a USB hard disk or USB ﬂash drive, in the USB

2.0 port on the rear panel of your wireless router. Ensure that the USB

storage device is formatted and partitioned properly. Refer to the ASUS

website at http://event.asus.com/2009/networks/disksupport/ for the

ﬁle system support table.

3.5.1 Using AiDisk

AiDisk allows you to share ﬁles stored on a connected USB device

through the Internet. AiDisk also assists you with setting up ASUS

DDNS and an FTP server.

To use AiDisk:

1. From the navigation panel, go to General > USB application,

then click the AiDisk icon.

2. From the Welcome to AiDisk wizard screen, click Go.

4. Create your domain name via the ASUS DDNS services, read

the Terms of Service and then select I will use the service and

accept the Terms of service and key in your domain name.

When done, click Next.

You can also select Skip ASUS DDNS settings then click Next

to skip the DDNS setting.

5. Click Finish to complete the setting.

6. To access the FTP site that you created, launch a web browser

or a third-party FTP client utility and key in the ftp link

(ftp://<domain name>.asuscomm.com) you have previously

created.

3. Select the access rights that you want to assign to the clients

accessing your shared data.

3.5.2 Using Servers Center

Servers Center allows you to share the media ﬁles from the USB

disk via a Media Server directory, Samba share service, or FTP

share service. You can also conﬁgure other settings for the USB

disk in the Servers Center.

Using Media Server

Your wireless router allows DLNA-supported devices to access

multimedia ﬁles from the USB disk connected to your wireless

router.

NOTE: Before using the DLNA Media Server function, connect your

device to the RT-AC1900P’s network.

To launch the Media Server setting page, go to General > USB

application > Servers Center > Media Servers tab. Refer to the

following for the descriptions of the ﬁelds:

• Enable DLNA Media Server: Select ON/OFF to enable/

disable the DLNA Media Server.

Enable iTunes Server?: Select ON/OFF to enable/disable the

iTunes Server.

• Media server directory: Select your media server directory

and click Apply to share ﬁles from the USB disk to media

devices in the network.

• Media Server Status: Displays the status of the media server.

Using Network Place (Samba) Share service

Network Place (Samba) Share allows you to set up the accounts

and permissions for the Samba service.

To use Samba share:

1. From the navigation panel, go to General > USB application >

Servers Center.

NOTE: Network Place (Samba) Share is enabled by default.

To delete an existing account:

a) Select the account that you want to delete.

b) Click .

c) When prompted, click Delete to conﬁrm the account

deletion.

To add a folder:

a) Click .

b) Enter the folder name, and click Add. The folder that you

created will be added to the folder list.

2. Follow the steps below to add, delete, or modify an account.

To create a new account:

a) Click to add new account.

b) In the Account and Password ﬁelds, key in the name and

password of your network client. Retype the password to

conﬁrm. Click Add to add the account to the list.

3. From the list of folders, select the type of access permission

that you want to assign for speciﬁc folders:

• R/W: Select this option to assign read/write access.

• R: Select this option to assign read-only access.

• No: Select this option if you do not want to share a speciﬁc

ﬁle folder.

4. Click Apply to apply the changes.

Using the FTP Share service

FTP share enables an FTP server to share ﬁles from USB disk to

other devices via your local area network or via the Internet.

IMPORTANT:

• EnsurethatyousafelyremovetheUSBdisk.Incorrectremovalofthe

USB disk may cause data corruption.

• TosafelyremovetheUSBdisk,refertothesectionSafely removing

the USB disk under 3.1.3 Monitoring your USB device.

To use FTP Share service:

NOTE: Ensure that you have set up your FTP server through

AiDisk. For more details, refer to the section 3.5.1 Using AiDisk.

1. From the navigation panel, click General > USB application >

Servers Center > FTP Share tab.

2. From the list of folders, select the type of access rights that you

want to assign for speciﬁc folders:

• R/W: Select to assign read/write access for a speciﬁc folder.

• W: Select to assign write only access for a speciﬁc folder.

• R: Select to assign read only access for a speciﬁc folder.

• No: Select this option if you do not want to share a speciﬁc

folder.

3. Click Apply to conﬁrm the changes.

4. To access the FTP server, key in the ftp link

ftp://<hostname>.asuscomm.com and your user name and

password on a web browser or a third-party FTP utility.

2. Conﬁgure the following settings:

• MaximumLoginUser

Set the maximum number of concurrent connections of the

Network Neighborhood or FTP Server.

NOTE: Some FTP clients may establish more than one connection.

Setting this number too low will lead to login failures.

• DeviceName

Assigns the name of the device as shown on the network.

For example, for a device with the name ABC, enter //ABC on

the Internet Explorer address bar to access the Network Place

service.

Miscellaneous setting

Miscellaneous setting allows you to conﬁgure other settings for

the USB disk, including the maximum number of user logins,

the device name, work group, and character set used on the FTP

server.

To conﬁgure Miscellaneous settings:

1. From the navigation panel, click General > USB application >

Servers Center > Miscellaneous setting tab.

• WorkGroup

Assigns the name of the local RT-AC1900P network as seen in

Network Neighborhood.

NOTE: For Device Name and Work Group, the standard input

characters include letters (a-z, A-Z), digits (0-9), space, underscores(_),

and hyphens(-). The ﬁrst and last character should not contain any

spaces. An invalid workgroup name makes it harder for other devices to

ﬁnd your device in the network.

• CharactersetonFTPServer

Select the appropriate encoding used during data exchange

on the FTP server.

3.5.3 3G/4G

3G/4G USB modems can be connected to RT-AC1900P to allow

Internet access.

NOTE: For a list of veriﬁed USB modems, please visit:

http://event.asus.com/2009/networks/3gsupport/

To set up 3G/4G internet access:

1. From the navigation panel, click General > USB application >

3G/4G.

2. In the Enable USB Modem ﬁeld, select Yes .

3. Set up the following:

• Location: Select your 3G/4G service provider’s location from

the dropdown list.

• ISP: Select your Internet Service Provider (ISP) from the

dropdown list.

• APN (Access Point Name) service (optional): Contact your

3G/4G service provider for detailed information.

• Dial Number and PIN code: The 3G/4G provider’s access

number and PIN code for connection.

NOTE: PIN code may vary from diﬀerent providers.

• Username / Password: The username and password will be

provided by the 3G/4G network carrier.

• USB Adapter: Choose your USB 3G / 4G adapter from the

dropdown list. If you are not sure of your USB adapter’s

model or the model is not listed in the options, select Auto.

4. Click Apply.

NOTE: The router will reboot for the settings to take eﬀect.

3.6 Using AiCloud

AiCloud is a cloud service application that allows you to save, sync,

share, and access your ﬁles.

To use AiCloud:

1. From Google Play Store or Apple Store, download and install

the ASUS AiCloud app to your smart device.

2. Connect your smart device to your network. Follow the

instructions to complete the AiCloud setup process.

3.6.1 Cloud Disk

To create a cloud disk:

1. Insert a USB storage device into the wireless router.

2. Turn on Cloud Disk.

3. Go to https://router.asus.com and enter the router login

account and password. For better user experience, we

recommend that you use Google Chrome or Firefox.

4. You can now start accessing Cloud Disk ﬁles on devices

connected to the network.

NOTE: When accessing the devices that are connected to the network,

you need to enter the device’s user name and password manually, which

will not be saved by AiCloud for security reason.

RT-AC68HP

3.6.2 Smart Access

The Smart Access function allows you to easily access your home

network via your router’s domain name.

NOTES:

• YoucancreateadomainnameforyourrouterwithASUSDDNS.For

more details, refer to section 4.3.5 DDNS.

• Bydefault,AiCloudprovidesasecureHTTPSconnection.Keyin

https://[yourASUSDDNSname].asuscomm.com for a very secure

Cloud Disk and Smart Access usage.

3.6.3 Smart Sync

To use Smart Sync:

1. Launch AiCloud, click Smart Sync > Go.

2. Select ON to enable Smart Sync.

3. Click Add new account.

4. Enter your ASUS WebStorage account password and select the

directory that you want to sync with WebStorage.

5. Click Apply.

4 Conﬁguring the Advanced

Settings

4.1 Wireless

4.1.1 General

The General tab allows you to conﬁgure the basic wireless

settings.

To conﬁgure the basic wireless settings:

1. From the navigation panel, go to Advanced Settings >

Wireless > General tab.

2. Select 2.4GHz or 5GHz as the frequency band for your wireless

network.

3. Assign a unique name containing up to 32 characters for your

SSID (Service Set Identiﬁer) or network name to identify your

wireless network. Wi-Fi devices can identify and connect to

the wireless network via your assigned SSID. The SSIDs on the

information banner are updated once new SSIDs are saved to

the settings.

NOTE: You can assign unique SSIDs for the 2.4 GHz and 5GHz frequency

bands.

4. In the Hide SSID ﬁeld, select Ye s to prevent wireless devices

from detecting your SSID. When this function is enabled, you

would need to enter the SSID manually on the wireless device

to access the wireless network.

5. Select any of these wireless mode options to determine the

types of wireless devices that can connect to your wireless

router:

• Auto: Select Auto to allow 802.11AC, 802.11n, 802.11g, and

802.11b devices to connect to the wireless router.

• Legacy: Select Legacy to allow 802.11b/g/n devices to

connect to the wireless router. Hardware that supports

802.11n natively, however, will only run at a maximum speed

of 54Mbps.

• N only: Select N only to maximize wireless N performance.

This setting prevents 802.11g and 802.11b devices from

connecting to the wireless router.

6. Select the operating channel for your wireless router. Select

Auto to allow the wireless router to automatically select the

channel that has the least amount of interference.

7. Select any of these channel bandwidth to accommodate higher

transmission speeds:

40MHz: Select this bandwidth to maximize the wireless

throughput.

20MHz (default): Select this bandwidth if you encounter some

issues with your wireless connection.

8. Select any of these authentication methods:

• Open System: This option provides no security.

• Shared Key: You must use WEP encryption and enter at least

one shared key.

• WPA/WPA2 Personal/WPA Auto-Personal: This option

provides strong security. You can use either WPA (with

TKIP) or WPA2 (with AES). If you select this option, you must

use TKIP + AES encryption and enter the WPA passphrase

(network key).

• WPA/WPA2 Enterprise/WPA Auto-Enterprise: This option

provides very strong security. It is with integrated EAP server

or an external RADIUS back-end authentication server.

• Radius with 802.1x

NOTE: Your wireless router supports the maximum transmission rate

of 54Mbps when the Wireless Mode is set to Auto and encryption

method is WEP or TKIP.

9. Select any of these WEP (Wired Equivalent Privacy) Encryption

options for the data transmitted over your wireless network:

• Oﬀ: Disables WEP encryption

• 64-bit: Enables weak WEP encryption

• 128-bit: Enables improved WEP encryption.

10.When done, click Apply.

4.1.2 WPS

WPS (Wi-Fi Protected Setup) is a wireless security standard that

allows you to easily connect devices to a wireless network. You

can conﬁgure the WPS function via the PIN code or WPS button.

NOTE: Ensure that the devices support WPS.

To enable WPS on your wireless network:

1. From the navigation panel, go to Advanced Settings >

Wireless > WPS tab.

2. In the Enable WPS ﬁeld, move the slider to ON.

3. WPS uses 2.4GHz by default. If you want to change the

frequency to 5GHz, turn OFF the WPS function, click Switch

Frequency in the Current Frequency ﬁeld, and turn WPS ON

again.

NOTE: WPS supports authentication using Open System, WPA-Personal,

and WPA2-Personal. WPS does not support a wireless network that uses

a Shared Key, WPA-Enterprise, WPA2-Enterprise, and RADIUS encryption

method.

3. In the WPS Method ﬁeld, select Push Button or Client PIN

code. If you select Push Button, go to step 4. If you select

Client PIN code, go to step 5.

4. To set up WPS using the router’s WPS button, follow these

steps:

a. Click Start or press the WPS button found at the rear of the

wireless router.

b. Press the WPS button on your wireless device. This is

normally identiﬁed by the WPS logo.

NOTE: Check your wireless device or its user manual for the location of

the WPS button.

c. The wireless router will scan for any available WPS devices.

If the wireless router does not ﬁnd any WPS devices, it will

switch to standby mode.

5. To set up WPS using the Client’s PIN code, follow these steps:

a. Locate the WPS PIN code on your wireless device’s user

manual or on the device itself.

b. Key in the Client PIN code on the text box.

c. Click Start to put your wireless router into WPS survey mode.

The router’s LED indicators quickly ﬂash three times until the

WPS setup is completed.

4.1.3 Bridge

Bridge or WDS (Wireless Distribution System) allows your ASUS

wireless router to connect to another wireless access point

exclusively, preventing other wireless devices or stations to access

your ASUS wireless router. It can also be considered as a wireless

repeater where your ASUS wireless router communicates with

another access point and other wireless devices.

To set up the wireless bridge:

1. From the navigation panel, go to Advanced Settings >

Wireless > Bridge tab.

2. Select the frequency band for the wireless bridge.

3. In the AP Mode ﬁeld, select any of these options:

• APOnly: Disables the Wireless Bridge function.

• WDSOnly: Enables the Wireless Bridge feature but prevents

other wireless devices/stations from connecting to the

router.

• HYBRID: Enables the Wireless Bridge feature and allows

other wireless devices/stations to connect to the router.

NOTE: In Hybrid mode, wireless devices connected to the ASUS wireless

router will only receive half the connection speed of the Access Point.

4. In the Connect to APs in list ﬁeld, click Yes if you want to

connect to an Access Point listed in the Remote AP List.

5. In the Control Channel ﬁeld, select the operating channel

for the wireless bridge. Select Auto to allow the router to

automatically select the channel with the least amount of

interference.

NOTE: Channel availability varies per country or region.

6. On the Remote AP List, key in a MAC address and click the Add

button to enter the MAC address of other available Access

Points.

NOTE: Any Access Point added to the list should be on the same Control

Channel as the ASUS wireless router.

7. Click Apply.

4.1.4 Wireless MAC Filter

Wireless MAC ﬁlter provides control over packets transmitted to

a speciﬁed MAC (Media Access Control) address on your wireless

network.

To set up the Wireless MAC ﬁlter:

1. From the navigation panel, go to Advanced Settings >

Wireless > Wireless MAC Filter tab.

2. In the Frequency ﬁeld, select the frequency band that you

want to use for the Wireless MAC ﬁlter.

3. In the MAC Filter Mode dropdown list, select either Accept or

Reject.

• SelectAccept to allow devices in the MAC ﬁlter list to access

to the wireless network.

• SelectReject to prevent devices in the MAC ﬁlter list to

access to the wireless network.

4. On the MAC ﬁlter list, click the Add button and key in the

MAC address of the wireless device.

5. Click Apply.

4.1.5 RADIUS Setting

RADIUS (Remote Authentication Dial In User Service) Setting

provides an extra layer of security when you choose WPA-

Enterprise, WPA2-Enterprise, or Radius with 802.1x as your

Authentication Mode.

To set up wireless RADIUS settings:

1. Ensure that the wireless router’s authentication mode is set to

WPA-Enterprise, WPA2-Enterprise, or Radius with 802.1x.

NOTE: Please refer to section 4.1.1 General section for conﬁguring your

wireless router’s Authentication Mode.

2. From the navigation panel, go to Advanced Settings >

Wireless > RADIUS Setting.

3. Select the frequency band.

4. In the Server IP Address ﬁeld, key in your RADIUS server’s IP

Address.

5. In the Connection Secret ﬁeld, assign the password to access

your RADIUS server.

6. Click Apply.

In the Professional Settings screen, you can conﬁgure the

following:

• Frequency: Select the frequency band that the professional

settings will be applied to.

• Enable Radio: Select Yes to enable wireless networking.

Select No to disable wireless networking.

• Date to Enable Radio (weekdays): You can specify which

days of the week wireless networking is enabled.

• Time of Day to Enable Radio: You can specify a time range

when wireless networking is enabled during the week.

4.1.6 Professional

The Professional screen provides advanced conﬁguration options.

NOTE: We recommend that you use the default values on this page.

• Date to Enable Radio (weekend): You can specify which

days of the weekend wireless networking is enabled.

• Time of Day to Enable Radio: You can specify a time range

when wireless networking is enabled during the weekend.

• Set AP isolated: The Set AP isolated item prevents wireless

devices on your network from communicating with each

other. This feature is useful if many guests frequently join or

leave your network. Select Ye s to enable this feature or select

No to disable.

• Multicast rate (Mbps): Select the multicast transmission

rate or click Disable to switch oﬀ simultaneous single

transmission.

• Preamble Type: Preamble Type deﬁnes the length of time

that the router spent for CRC (Cyclic Redundancy Check). CRC

is a method of detecting errors during data transmission.

Select Short for a busy wireless network with high network

traﬃc. Select Long if your wireless network is composed of

older or legacy wireless devices.

• RTS Threshold: Select a lower value for RTS (Request to

Send) Threshold to improve wireless communication in a

busy or noisy wireless network with high network traﬃc and

numerous wireless devices.

• DTIM Interval: DTIM (Delivery Traﬃc Indication Message)

Interval or Data Beacon Rate is the time interval before a

signal is sent to a wireless device in sleep mode indicating

that a data packet is awaiting delivery. The default value is

three milliseconds.

• Beacon Interval: Beacon Interval is the time between one

DTIM and the next. The default value is 100 milliseconds.

Lower the Beacon Interval value for an unstable wireless

connection or for roaming devices.

• Enable TX Bursting: Enable TX Bursting improves

transmission speed between the wireless router and 802.11g

devices.

• Wireless multicast forwarding: Select Enable to allow the

wireless router to forward multicast traﬃc to other wireless

devices that support multicast. Select Disable to prevent the

router from forwarding multicast transmissions.

• Enable WMM APSD: Enable WMM APSD (Wi-Fi Multimedia

Automatic Power Save Delivery) to improve power

management between wireless devices. Select Disable to

switch oﬀ WMM APSD.

• TX Power adjustment: TX Power adjustment refers to the

milliWatts (mW) needed to power the radio signal output of

the wireless router. Enter a value between 0 to 100.

NOTE: Increasing the TX Power adjustment values may aﬀect the

stability of the wireless network.

4.2 LAN

4.2.1 LAN IP

The LAN IP screen allows you to modify the LAN IP settings of your

wireless router.

NOTE: Any changes to the LAN IP address will be reﬂected on your

DHCP settings.

To modify the LAN IP settings:

1. From the navigation panel, go to Advanced Settings > LAN >

LAN IP tab.

2. Modify the IP address and Subnet Mask.

3. When done, click Apply.

4.2.2 DHCP Server

Your wireless router uses DHCP to assign IP addresses

automatically on your network. You can specify the IP address

range and lease time for the clients on your network.

To conﬁgure the DHCP server:

1. From the navigation panel, go to Advanced Settings > LAN >

DHCP Server tab.

2. In the Enable the DHCP Server ﬁeld, tick Yes.

3. In the Domain Name text box, enter a domain name for the

wireless router.

4. In the IP Pool Starting Address ﬁeld, key in the starting IP

address.

5. In the IP Pool Ending Address ﬁeld, key in the ending IP

address.

6. In the Lease Time ﬁeld, specify in seconds when an assigned

IP address will expire. Once it reaches this time limit, the DHCP

server will then assign a new IP address.

NOTES:

• We recommend that you use an IP address format of 192.168.1.xxx

(where xxx can be any number between 2 and 254) when specifying

an IP address range.

• AnIPPoolStartingAddressshouldnotbegreaterthantheIPPool

Ending Address.

7. In the DNS and Server Settings section, key in your DNS

Server and WINS Server IP address if needed.

8. Your wireless router can also manually assign IP addresses to

devices on the network. On the Enable Manual Assignment

ﬁeld, choose Yes to assign an IP address to speciﬁc MAC

addresses on the network. Up to 32 MAC Addresses can be

added to the DHCP list for manual assignment.

4.2.3 Route

If your network makes use of more than one wireless router, you

can conﬁgure a routing table to share the same Internet service.

NOTE: We recommend that you do not change the default route

settings unless you have advanced knowledge of routing tables.

To conﬁgure the LAN Routing table:

1. From the navigation panel, go to Advanced Settings > LAN >

Route tab.

2. On the Enable static routes ﬁeld, choose Yes.

3. On the Static Route List, enter the network information of

other access points or nodes. Click the Add or Delete

button to add or remove a device on the list.

4. Click Apply.

4.2.4 IPTV

The wireless router supports connection to IPTV services through

an ISP or a LAN. The IPTV tab provides the conﬁguration settings

needed to set up IPTV, VoIP, multicasting, and UDP for your

service. Contact your ISP for speciﬁc information regarding your

service.

4.3 WAN

4.3.1 Internet Connection

The Internet Connection screen allows you to conﬁgure the

settings of various WAN connection types.

To conﬁgure the WAN connection settings:

1. From the navigation panel, go to Advanced Settings > WAN >

Internet Connection tab.

2. Conﬁgure the following settings below. When done, click

Apply.

• WAN Connection Type: Choose your Internet Service Provider

type. The choices are Automatic IP, PPPoE, PPTP, L2TP or

ﬁxed IP. Consult your ISP if the router is unable to obtain a

valid IP address or if you are unsure the WAN connection type.

• Enable WAN: Select Yes to allow the router Internet access.

Select No to disable Internet access.

• Enable NAT: NAT (Network Address Translation) is a system

where one public IP (WAN IP) is used to provide Internet

access to network clients with a private IP address in a LAN.

The private IP address of each network client is saved in a NAT

table and is used to route incoming data packets.

• Enable UPnP: UPnP (Universal Plug and Play) allows several

devices (such as routers, televisions, stereo systems, game

consoles, and cellular phone), to be controlled via an IP-based

network with or without a central control through a gateway.

UPnP connects PCs of all form factors, providing a seamless

network for remote conﬁguration and data transfer. Using

UPnP, a new network device is discovered automatically.

Once connected to the network, devices can be remotely

conﬁgured to support P2P applications, interactive gaming,

video conferencing, and web or proxy servers. Unlike Port

forwarding, which involves manually conﬁguring port

settings, UPnP automatically conﬁgures the router to accept

incoming connections and direct requests to a speciﬁc PC on

the local network.

• Connect to DNS Server: Allows this router to get the DNS

IP address from the ISP automatically. A DNS is a host on

the Internet that translates Internet names to numeric IP

addresses.

• Authentication: This item may be speciﬁed by some ISPs.

Check with your ISP and ﬁll them in if required.

• Host Name: This ﬁeld allows you to provide a host name for

your router. It is usually a special requirement from your ISP.

If your ISP assigned a host name to your computer, enter the

host name here.

• MAC Address: MAC (Media Access Control) address is a

unique identiﬁer for your networking device. Some ISPs

monitor the MAC address of networking devices that connect

to their service and reject any unrecognized device that

attempt to connect. To avoid connection issues due to an

unregistered MAC address, you can:

• ContactyourISPandupdatetheMACaddressassociated

with your ISP service.

• CloneorchangetheMACaddressoftheASUSwirelessrouter

to match the MAC address of the previous networking device

recognized by the ISP.

4.3.2 Port Trigger

Port range triggering opens a predetermined incoming port for a

limited period of time whenever a client on the local area network

makes an outgoing connection to a speciﬁed port. Port triggering

is used in the following scenarios:

• More than one local client needs port forwarding for the

same application at a diﬀerent time.

• An application requires speciﬁc incoming ports that are

diﬀerent from the outgoing ports.

To set up Port Trigger:

1. From the navigation panel, go to Advanced Settings > WAN >

Port Trigger tab.

2. Conﬁgure the following settings below. When done, click

Apply.

• Enable Port Trigger: Choose Ye s to enable Port Trigger.

• Well-Known Applications: Select popular games and web

services to add to the Port Trigger List.

• Description: Enter a short name or description for the service.

• Trigger Port: Specify a trigger port to open the incoming port.

• Protocol: Select the protocol, TCP, or UDP.

• Incoming Port: Specify an incoming port to receive inbound

data from the Internet.

• Protocol: Select the protocol, TCP, or UDP.

NOTES:

• WhenconnectingtoanIRCserver,aclientPCmakesanoutgoing

connection using the trigger port range 66660-7000. The IRC server

responds by verifying the username and creating a new connection

to the client PC using an incoming port.

• IfPortTriggerisdisabled,therouterdropstheconnectionbecause

it is unable to determine which PC is requesting for IRC access.

When Port Trigger is enabled, the router assigns an incoming port to

receive the inbound data. This incoming port closes once a specific

time period has elapsed because the router is unsure when the

application has been terminated.

• Porttriggeringonlyallowsoneclientinthenetworktousea

particular service and a specific incoming port at the same time.

• Youcannotusethesameapplicationtotriggeraportinmorethan

one PC at the same time. The router will only forward the port back

to the last computer to send the router a request/trigger.

4.3.3 Virtual Server/Port Forwarding

Port forwarding is a method to direct network traﬃc from the

Internet to a speciﬁc port or a speciﬁc range of ports to a device

or number of devices on your local network. Setting up Port

Forwarding on your router allows PCs outside the network to

access speciﬁc services provided by a PC in your network.

NOTE: When port forwarding is enabled, the ASUS router blocks

unsolicited inbound traﬃc from the Internet and only allows replies

from outbound requests from the LAN. The network client does not

have access to the Internet directly, and vice versa.

To set up Port Forwarding:

1. From the navigation panel, go to Advanced Settings > WAN >

Virtual Server / Port Forwarding tab.

2. Conﬁgure the following settings below. When done, click

Apply.

• Enable Port Forwarding: Choose Yes to enable Port

Forwarding.

• Famous Server List: Determine which type of service you

want to access.

• Famous Game List: This item lists ports required for popular

online games to work correctly.

• FTP Server Port: Avoid assigning the port range 20:21 for

your FTP server as this would conﬂict with the router’s native

FTP server assignment.

• Service Name: Enter a service name.

• Port Range: If you want to specify a Port Range for clients

on the same network, enter the Service Name, the Port

Range (e.g. 10200:10300), the LAN IP address, and leave the

Local Port empty. Port range accepts various formats such

as Port Range (300:350), individual ports (566,789) or Mix

(1015:1024,3021).

NOTES:

• Whenyournetwork’sfirewallisdisabledandyouset80astheHTTP

server’s port range for your WAN setup, then your http server/web

server would be in conflict with the router’s web user interface.

• Anetworkmakesuseofportsinordertoexchangedata,witheach

port assigned a port number and a specific task. For example, port 80

is used for HTTP. A specific port can only be used by one application

or service at a time. Hence, two PCs attempting to access data

through the same port at the same time would fail. For example, you

cannot set up Port Forwarding for port 100 for two PCs at the same

time.

• Local IP: Key in the client’s LAN IP address.

NOTE: Use a static IP address for the local client to make port forwarding

work properly. Refer to section 4.2 LAN for information.

• Local Port: Enter a speciﬁc port to receive forwarded packets.

Leave this ﬁeld blank if you want the incoming packets to be

redirected to the speciﬁed port range.

• Protocol: Select the protocol. If you are unsure, select BOTH.

To check if Port Forwarding has been conﬁgured successfully:

• Ensure that your server or application is set up and running.

• You will need a client outside your LAN but has Internet

access (referred to as “Internet client”). This client should not

be connected to the ASUS router.

• On the Internet client, use the router’s WAN IP to access the

server. If port forwarding has been successful, you should be

able to access the ﬁles or applications.

Diﬀerences between port trigger and port forwarding:

• Port triggering will work even without setting up a speciﬁc

LAN IP address. Unlike port forwarding, which requires a

static LAN IP address, port triggering allows dynamic port

forwarding using the router. Predetermined port ranges are

conﬁgured to accept incoming connections for a limited

period of time. Port triggering allows multiple computers

to run applications that would normally require manually

forwarding the same ports to each PC on the network.

• Port triggering is more secure than port forwarding since the

incoming ports are not open all the time. They are opened

only when an application is making an outgoing connection

through the trigger port.

4.3.4 DMZ

Virtual DMZ exposes one client to the Internet, allowing this

client to receive all inbound packets directed to your Local Area

Network.

Inbound traﬃc from the Internet is usually discarded and routed

to a speciﬁc client only if port forwarding or a port trigger has

been conﬁgured on the network. In a DMZ conﬁguration, one

network client receives all inbound packets.

Setting up DMZ on a network is useful when you need incoming

ports open or you want to host a domain, web, or e-mail server.

CAUTION: Opening all the ports on a client to the Internet makes the

network vulnerable to outside attacks. Please be aware of the security

risks involved in using DMZ.

To set up DMZ:

1. From the navigation panel, go to Advanced Settings > WAN >

DMZ tab.

2. Conﬁgure the setting below. When done, click Apply.

• IP address of Exposed Station: Key in the client’s LAN IP

address that will provide the DMZ service and be exposed

on the Internet. Ensure that the server client has a static IP

address.

To remove DMZ:

1. Delete the client’s LAN IP address from the IP Address of

Exposed Station text box.

2. When done, click Apply.

4.3.5 DDNS

Setting up DDNS (Dynamic DNS) allows you to access the router

from outside your network through the provided ASUS DDNS

Service or another DDNS service.

To set up DDNS:

1. From the navigation panel, go to Advanced Settings > WAN >

DDNS tab.

2. Conﬁgure the following settings below. When done, click

Apply.

• Enable the DDNS Client: Enable DDNS to access the ASUS

router via the DNS name rather than WAN IP address.

• Server and Host Name: Choose ASUS DDNS or other DDNS.

If you want to use ASUS DDNS, ﬁll in the Host Name in the

format of xxx.asuscomm.com (xxx is your host name).

• If you want to use a diﬀerent DDNS service, click FREE TRIAL

and register online ﬁrst. Fill in the User Name or E-mail

Address and Password or DDNS Key ﬁelds.

• Enable wildcard: Enable wildcard if your DDNS service

requires one.

NOTES:

DDNS service will not work under these conditions:

• WhenthewirelessrouterisusingaprivateWANIPaddress(192.168.

x.x, 10.x.x.x, or 172.16.x.x), as indicated by a yellow text.

• TheroutermaybeonanetworkthatusesmultipleNATtables.

4.3.6 NAT Passthrough

NAT Passthrough allows a Virtual Private Network (VPN)

connection to pass through the router to the network clients.

PPTP Passthrough, L2TP Passthrough, IPsec Passthrough and RTSP

Passthrough are enabled by default.

To enable / disable the NAT Passthrough settings, go to the

Advanced Settings > WAN > NAT Passthrough tab. When done,

click Apply.

4.4 IPv6

This wireless router supports IPv6 addressing, a system that

supports more IP addresses. This standard is not yet widely

available. Contact your ISP if your Internet service supports IPv6.

To set up IPv6:

1. From the navigation panel, go to Advanced Settings > IPv6.

2. Select your Connection Type. The conﬁguration options vary

depending on your selected connection type.

3. Enter your IPv6 LAN and DNS settings.

4. Click Apply.

NOTE: Please refer to your ISP regarding speciﬁc IPv6 information for

your Internet service.

4.5 VPN Server

VPN (Virtual Private Network) provides a secure communication

to a remote computer or remote network using a public network

such as the Internet.

NOTE: Before setting up a VPN connection, you would need the IP

address or domain name of the VPN server you are trying to access.

To set up access to a VPN server:

1. From the navigation panel, go to Advanced Settings > VPN

Server.

2. On the Enable PPTP Server ﬁeld, select Yes .

3. On the Network Place (Samba) Support ﬁeld, select Ye s.

4. Enter the user name and password for accessing the VPN

server. Click the button.

5. Click Apply.

NOTE: For advanced VPN server settings, click the VPN Server tab to

conﬁgure broadcast support, authentication, MPPE Encryption, and

Client IP address range.

4.6 Firewall

The wireless router can serve as a hardware ﬁrewall for your

network.

NOTE: The Firewall feature is enabled by default.

4.6.1 General

To set up basic Firewall settings:

1. From the navigation panel, go to Advanced Settings >

Firewall > General tab.

2. On the Enable Firewall ﬁeld, select Yes.

3. On the Enable DoS protection, select Ye s to protect your

network from DoS (Denial of Service) attacks though this may

aﬀect your router’s performance.

4. You can also monitor packets exchanged between the LAN

and WAN connection. On the Logged packets type, select

Dropped, Accepted, or Both.

5. Click Apply.

4.6.2 URL Filter

You can specify keywords or web addresses to prevent access to

speciﬁc URLs.

NOTE: The URL Filter is based on a DNS query. If a network client has

already accessed a website such as http://www.abcxxx.com, then the

website will not be blocked (a DNS cache in the system stores previously

visited websites). To resolve this issue, clear the DNS cache before

setting up the URL Filter.

To set up a URL ﬁlter:

1. From the navigation panel, go to Advanced Settings >

Firewall > URL Filter tab.

2. On the Enable URL Filter ﬁeld, select Enabled.

3. Enter a URL and click the button.

4. Click Apply.

4.6.3 Keyword ﬁlter

Keyword ﬁlter blocks access to webpages containing speciﬁed

keywords.

To set up a keyword ﬁlter:

1. From the navigation panel, go to Advanced Settings >

Firewall > Keyword Filter tab.

2. On the Enable Keyword Filter ﬁeld, select Enabled.

3. Enter a word or phrase and click the Add button.

4. Click Apply.

NOTES:

• The Keyword Filter is based on a DNS query. If a network client has

already accessed a website such as http://www.abcxxx.com, then

the website will not be blocked (a DNS cache in the system stores

previously visited websites). To resolve this issue, clear the DNS cache

before setting up the Keyword Filter.

• Web pages compressed using HTTP compression cannot be filtered.

HTTPS pages also cannot be blocked using a keyword filter.

4.6.4 Network Services Filter

The Network Services Filter blocks LAN to WAN packet exchanges

and restricts network clients from accessing speciﬁc web services

such as Telnet or FTP.

To set up a Network Service ﬁlter:

1. From the navigation panel, go to Advanced Settings >

Firewall > Network Service Filter tab.

2. On the Enable Network Services Filter ﬁeld, select Yes .

3. Select the Filter table type. Black List blocks the speciﬁed

network services. White List limits access to only the speciﬁed

network services.

4. Specify the day and time when the ﬁlters will be active.

5. To specify a Network Service to ﬁlter, enter the Source IP,

Destination IP, Port Range, and Protocol. Click the button.

6. Click Apply.

4.7 Administration

4.7.1 Operation Mode

The Operation Mode page allows you to select the appropriate

mode for your network.

To set up the operating mode:

1. From the navigation panel, go to Advanced Settings >

Administration > Operation Mode tab.

2. Select any of these operation modes:

• Wireless router mode (default): In wireless router mode,

the wireless router connects to the Internet and provides

Internet access to available devices on its own local network.

•  Media Bridge: This setup requires two wireless routers.

The second router serves as a media bridge where multiple

devices such as Smart TVs and gaming consoles can be

connected via ethernet.

•  Access Point mode: In this mode, the router creates a new

wireless network on an exising network.

3. Click Apply.

NOTE: The router will reboot when you change the modes.

4.7.2 System

The System page allows you to conﬁgure your wireless router

settings.

To set up the System settings:

1. From the navigation panel, go to Advanced Settings >

Administration > System tab.

2. You can conﬁgure the following settings:

• Change router login password: You can change the

password and login name for the wireless router by entering

a new name and password.

• WPS button behavior: The physical WPS button on the

wireless router can be used to activate WPS.

• Time Zone: Select the time zone for your network.

• NTP Server: The wireless router can access a NTP (Network

time Protocol) server in order to synchronize the time.

• Enable Telnet: Click Yes to enable Telnet services on the

network. Click No to disable Telnet.

• Authentication Method: You can select HTTP, HTTPS, or

both protocols to secure router access.

• Enable Web Access from WAN: Select Ye s to allow devices

outside the network to access the wireless router GUI

settings. Select No to prevent access.

• Only allow speciﬁc IP: Click Yes if you want to specify the IP

addresses of devices that are allowed access to the wireless

router GUI settings from WAN.

• Client List: Enter the WAN IP addresses of networking

devices allowed to access the wireless router settings. This

list will be used if you clicked Yes in the Only allow speciﬁc

IP item.

3. Click Apply.

4.7.3 Firmware Upgrade

NOTE: Download the latest ﬁrmware from the ASUS website at

http://www.asus.com

To upgrade the ﬁrmware:

1. From the navigation panel, go to Advanced Settings >

Administration > Firmware Upgrade tab.

2. In the New Firmware File ﬁeld, click Browse to locate the

downloaded ﬁle.

3. Click Upload.

NOTES:

• Whentheupgradeprocessiscomplete,waitforsometimeforthe

system to reboot.

• Iftheupgradeprocessfails,thewirelessrouterautomaticallyenters

rescue mode and the power LED indicator on the front panel starts

flashing slowly. To recover or restore the system, refer to section 5.2

Firmware Restoration.

4.7.4 Restore/Save/Upload Setting

To restore/save/upload wireless router settings:

1. From the navigation panel, go to Advanced Settings >

Administration > Restore/Save/Upload Setting tab.

2. Select the tasks that you want to do:

• Torestoretothedefaultfactorysettings,clickRestore, and

click OK in the conﬁrmation message.

• Tosavethecurrentsystemsettings,clickSave, navigate to

the folder where you intend to save the ﬁle and click Save.

• Torestorefromasavedsystemsettingsle,clickBrowse to

locate your ﬁle, then click Upload.

NOTE: If issues occur, upload the latest ﬁrmware version and conﬁgure

new settings. Do not restore the router to its default settings.

4.8 System Log

System Log contains your recorded network activities.

NOTE: System log resets when the router is rebooted or powered oﬀ.

To view your system log:

1. From the navigation panel, go to Advanced Settings > System

Log.

2. You can view your network activities in any of these tabs:

• GeneralLog

• DHCPLeases

• WirelessLog

• PortForwarding

• RoutingTable

5 Utilities

NOTES:

• Downloadandinstallthewirelessrouter'sutilitiesfromtheASUS

website:

 • DeviceDiscoveryv1.4.7.1athttp://dlcdnet.asus.com/pub/ASUS/

LiveUpdate/Release/Wireless/Discovery.zip

 • FirmwareRestorationv1.9.0.4athttp://dlcdnet.asus.com/pub/

ASUS/LiveUpdate/Release/Wireless/Rescue.zip

 • WindowsPrinterUtilityv1.0.5.5athttp://dlcdnet.asus.com/pub/

ASUS/LiveUpdate/Release/Wireless/Printer.zip

• TheutilitiesarenotsupportedonMACOS.

5.1 Device Discovery

Device Discovery is an ASUS WLAN utility that detects an ASUS

wireless router device, and allows you to conﬁgure the wireless

networking settings.

To launch the Device Discovery utility:

• Fromyourcomputer’sdesktop,click

Start > All Programs > ASUS Utility > RT-AC1900P Wireless

Router > Device Discovery.

RT-AC68HP

NOTE: When you set the router to Access Point mode, you need to use

Device Discovery to get the router’s IP address.

5.2 Firmware Restoration

Firmware Restoration is used on an ASUS Wireless Router that

failed during its ﬁrmware upgrading process. It uploads the

ﬁrmware that you specify. The process takes about three to four

minutes.

IMPORTANT: Launch the rescue mode on the router before using the

Firmware Restoration utility.

NOTE: This feature is not supported on MAC OS.

To launch the rescue mode and use the Firmware Restoration

utility:

1. Unplug the wireless router from the power source.

2. Hold the Reset button at the rear panel and simultaneously

replug the wireless router into the power source. Release the

Reset button when the Power LED at the front panel ﬂashes

slowly, which indicates that the wireless router is in the rescue

mode.

3. Set a static IP on your computer and use the following to set up

your TCP/IP settings:

IP address: 192.168.1.x

Subnet mask: 255.255.255.0

4. From your computer’s desktop, click

Start > All Programs > ASUS Utility RT-AC1900P Wireless

Router > Firmware Restoration.

5. Specify a ﬁrmware ﬁle, then click Upload.

NOTE: This is not a ﬁrmware upgrade utility and cannot be used on

a working ASUS Wireless Router. Normal ﬁrmware upgrades must be

done through the web interface. Refer to Chapter 4: Conﬁguring the

Advanced Settings for more details.

5.3 Setting up your printer server

5.3.1 ASUS EZ Printer Sharing

ASUS EZ Printing Sharing utility allows you to connect a USB

printer to your wireless router’s USB port and set up the print

server. This allows your network clients to print and scan ﬁles

wirelessly.

NOTE: The print server function is supported on Windows® XP,

Windows® Vista, and Windows® 7.

To set up the EZ Printer sharing mode:

1. From the navigation panel, go to General > USB Application >

Network Printer Server.

2. Click Download Now! to download the network printer utility.

NOTE: Network printer utility is supported on Windows® XP, Windows®

Vista, and Windows® 7 only. To install the utility on Mac OS, select Use

LPR protocol for sharing printer.

3. Unzip the downloaded ﬁle and click the Printer icon to run the

network printer setup program.

4. Follow the onscreen instructions to set up your hardware, then

click Next.

5. Wait a few minutes for the initial setup to ﬁnish. Click Next.

6. Click Finish to complete the installation.

RT-AC68HP

8. After the printer’s driver installation is complete, network

clients can now use the printer.

7. Follow the Windows® OS instructions to install the printer driver.

5.3.2 Using LPR to Share Printer

You can share your printer with computers running on Windows®

and MAC operating system using LPR/LPD (Line Printer Remote/

Line Printer Daemon).

Sharing your LPR printer

To share your LPR printer:

1. From the Windows® desktop, click Start > Devices and

Printers > Add a printer to run the Add Printer Wizard.

2. Select Add a local printer and then click Next.

3. Select Create a new port then set Type of Port to Standard

TCP/IP Port. Click New Port.

4. In the Hostname or IP address ﬁeld, key in the IP address of

the wireless router then click Next.

5. Select Custom then click Settings.

6. Set Protocol to LPR. In the Queue Name ﬁeld, key in

LPRServer then click OK to continue.

7. Click Next to ﬁnish setting up the standard TCP/IP port.

8. Install the printer driver from the vendor-model list. If your

printer is not in the list, click Have Disk to manually install the

printer drivers from a CD-ROM or ﬁle.

9. Click Next to accept the default name for the printer.

10. Click Finish to complete the installation.

5.4 Download Master

Download Master is a utility that helps you download ﬁles even

while your laptops or other devices are switched oﬀ.

NOTE: You need a USB device connected to the wireless router to use

Download Master.

To use Download Master:

1. Click General > USB application > Download Master to

download and install the utility automatically.

NOTE: If you have more than one USB drive, select the USB device you

want to download the ﬁles to.

2. After the download process is ﬁnished, click the Download

Master icon to start using the utility.

3. Click Add to add a download task.

4. Select a download type such as BitTorrent, HTTP, or FTP. Provide

a torrent ﬁle or a URL to begin downloading.

NOTE: For details on Bit Torrent, refer to section 5.4.1 Conﬁguring the

Bit Torrent download settings.

5. Use the navigation panel to conﬁgure the advanced settings.

To conﬁgure BitTorrent download settings:

1. From Download Master’s navigation panel, click Bit Torrent to

launch the Bit Torrent Setting page.

2. Select a speciﬁc port for your download task.

3. To prevent network congestion, you can limit the maximum

upload and download speeds under Speed Limits.

4. You can limit the maximum number of allowed peers and

enable or disable ﬁle encryption during downloads.

5.4.1 Conﬁguring Bit Torrent download settings

5.4.2 NZB settings

You can set up a USENET server to download NZB ﬁles. After

entering USENET settings, Apply.

6 Troubleshooting

This chapter provides solutions for issues you may encounter with

your router. If you encounter problems that are not mentioned in

this chapter, visit the ASUS support site at:

http://support.asus.com/ for more product information and

contact details of ASUS Technical Support.

6.1 Basic Troubleshooting

If you are having problems with your router, try these basic steps

in this section before looking for further solutions.

Upgrade Firmware to the latest version.

1. Launch the Web GUI. Go to Advanced Settings >

Administration > Firmware Upgrade tab. Click Check to

verify if the latest ﬁrmware is available.

2. If the latest ﬁrmware is available, visit the ASUS global

website at http://www.asus.com/Networks/Wireless_Routers/

RTAC1900P/#download to download the latest ﬁrmware.

3. From the Firmware Upgrade page, click Browse to locate the

ﬁrmware ﬁle.

4. Click Upload to upgrade the ﬁrmware.

100

Restart your network in the following sequence:

1. Turn oﬀ the modem.

2. Unplug the modem.

3. Turn oﬀ the router and computers.

4. Plug in the modem.

5. Turn on the modem and then wait for 2 minutes.

6. Turn on the router and then wait for 2 minutes.

7. Turn on computers.

Check if your Ethernet cables are plugged properly.

• WhentheEthernetcableconnectingtherouterwiththe

modem is plugged in properly, the WAN LED will be on.

• WhentheEthernetcableconnectingyourpowered-

on computer with the router is plugged in properly, the

corresponding LAN LED will be on.

Check if the wireless setting on your computer matches that

of your computer.

• Whenyouconnectyourcomputertotherouterwirelessly,

ensure that the SSID (wireless network name), encryption

mehtod, and password are correct.

Check if your network settings are correct.

• EachclientonthenetworkshouldhaveavalidIPaddress.ASUS

recommends that you use the wireless router’s DHCP server to

assign IP addresses to computers on your network.

101

• Somecablemodemserviceprovidersrequireyoutouse

the MAC address of the computer initially registered on

the account. You can view the MAC address in the web GUI,

Network Map > Clients page, and hover the mouse pointer

over your device in Client Status.

102

6.2 Frequently Asked Questions (FAQs)

I cannot access the router GUI using a web browser

• Ifyourcomputeriswired,checktheEthernetcableconnection

and LED status as described in the previous section.

• Ensurethatyouareusingthecorrectlogininformation.The

default factory login name and password is “admin/admin”.

Ensure that the Caps Lock key is disabled when you enter the

• Deletethecookiesandlesinyourwebbrowser.ForInternet

Explorer 8, follow these steps:

1. Launch Internet Explorer 8,

then click Tools > Internet

Options.

2. In the General tab, under

Browsing history, click

Delete…, select Temporary

Internet Files and Cookies

then click Delete.

NOTES:

• Thecommandsfordeletingcookiesandfilesvarywithweb

browsers.

• Disableproxyserversettings,cancelthedial-upconnection,

and set the TCP/IP settings to obtain IP addresses automatically.

For more details, refer to Chapter 1 of this user manual.

• EnsurethatyouuseCAT5eorCAT6ethernetcables.

103

The client cannot establish a wireless connection with the

router.

NOTE: If you are having issues connecting to 5Ghz network, make

sure that your wireless device supports 5Ghz or features dual band

capabilities.

• OutofRange:

 • Movetherouterclosertothewirelessclient.

 • Trytoadjustantennasoftheroutertothebestdirectionas

described in section 1.4 Positioning your router.

• DHCPserverhasbeendisabled:

1. Launch the web GUI. Go to General > Network Map>

Clients and search for the device that you want to connect

to the router.

2. If you cannot ﬁnd the device in the Network Map, go to

Advanced Settings > LAN > DHCP Server, Basic Conﬁg

list, select Ye s on the Enable the DHCP Server.

104

• SSIDhasbeenhidden.IfyourdevicecanndSSIDsfromother

routers but cannot ﬁnd your router’s SSID, go to Advanced

Settings > Wireless > General, select No on Hide SSID, and

select Auto on Control Channel.

• IfyouareusingawirelessLANadapter,checkifthewireless

channel in use conforms to the channels available in your

country/area. If not, adjust the channel, channel bandwidth,

and wireless mode.

• Ifyoustillcannotconnecttotherouterwirelessly,youcanreset

your router to factory default settings. In the router GUI,click

Administration > Restore/Save/Upload Setting and click

Restore.

105

Internet is not accessible.

• CheckifyourroutercanconnecttoyourISP’sWANIPaddress.

To do this, launch the web GUI and go to General> Network

Map, and check the Internet Status.

• IfyourroutercannotconnecttoyourISP’sWANIPaddress,

try restarting your network as described in the section

Restart your network in following sequence under Basic

Troubleshooting.

• ThedevicehasbeenblockedviatheParentalControlfunction.

Go to General > Parental Control and see if the device is

in the list. If the device is listed under Client Name, remove

the device using the Delete button or adjust the Time

Management Settings.

106

• IfthereisstillnoInternetaccess,trytorebootyourcomputer

and verify the network’s IP address and gateway address.

• CheckthestatusindicatorsontheADSLmodemandthe

wireless router. If the WAN LED on the wireless router is not ON,

check if all cables are plugged properly.

You forgot the SSID (network name) or network password

• SetupanewSSIDandencryptionkeyviaawiredconnection

(Ethernet cable). Launch the web GUI, go to Network Map,

click the router icon, enter a new SSID and encryption key, and

then click Apply.

• Resetyourroutertothedefaultsettings.LaunchthewebGUI,

go to Administration > Restore/Save/Upload Setting, and

click Restore. The default login account and password are both

“admin”.

How to restore the system to its default settings?

• GotoAdministration > Restore/Save/Upload Setting, and

click Restore.

The following are the factory default settings:

User Name: admin

Password: admin

Enable DHCP: Yes (if WAN cable is plugged in)

IP address: 192.168.1.1

Domain Name: (Blank)

Subnet Mask: 255.255.255.0

DNS Server 1: 192.168.1.1

DNS Server 2: (Blank)

SSID (2.4GHz): ASUS

SSID (5GHz): ASUS_5G

107

Firmware upgrade failed.

Launch the rescue mode and run the Firmware Restoration utility.

Refer to section 5.2 Firmware Restoration on how to use the

Firmware Restoration utility.

108

Cannot access Web GUI

A. Disable the proxy server, if enabled.

Windows® 7

1. Click Start > Internet Explorer

to launch the browser.

2. Click Tools > Internet options

> Connections tab > LAN

settings.

Before conﬁguring your wireless router, do the steps described in

this section for your host computer and network clients.

3. From the Local Area

Network (LAN) Settings

screen, untick Use a proxy

server for your LAN.

4. Click OK when done.

109

MAC OS

1. From your Safari

browser, click Safari

> Preferences >

Advanced > Change

Settings...

2. From the Network

screen, deselect FTP

Proxy and Web Proxy

(HTTP).

3. Cllick Apply Now when

done.

NOTE: Refer to your browser's help feature for details on disabling the

proxy server.

B. Set the TCP/IP settings to automatically obtain an IP

address.

Windows® 7

1. Click Start > Control Panel

> Network and Internet

> Network and Sharing

Center > Manage network

connections.

2. Select Internet Protocol

Version 4 (TCP/IPv4) or

Internet Protocol Version

6 (TCP/IPv6), then click

Properties.

110

3. To obtain the IPv4 IP

settings automatically,

tick Obtain an IP address

automatically.

To obtain the IPv6 IP

settings automatically, tick

Obtain an IPv6 address

automatically.

4. Click OK when done.

MAC OS

1. Click the Apple icon

located on the top left of

your screen.

2. Click System

Preferences > Network

> Conﬁgure...

3. From the TCP/IP tab,

select Using DHCP in

the Conﬁgure IPv4

dropdown list.

4. Cllick Apply Now when

done.

NOTE: Refer to your operating system’s help and support feature for

details on conﬁguring your computer’s TCP/IP settings.

111

C. Disable the dial-up connection, if enabled.

Windows® 7

1. Click Start > Internet Explorer

to launch the browser.

2. Click Tools > Internet options >

Connections tab.

3. Tick Never dial a connection.

4. Click OK when done.

NOTE: Refer to your browser's help feature for details on disabling the

dial-up connection.

112

Appendices

Notices

ASUS Recycling/Takeback Services

ASUS recycling and takeback programs come from our

commitment to the highest standards for protecting our

environment. We believe in providing solutions for you to be able

to responsibly recycle our products, batteries, other components,

as well as the packaging materials. Please go to http://csr.asus.

com/english/Takeback.htm for the detailed recycling information

in diﬀerent regions.

REACH

Complying with the REACH (Registration, Evaluation,

Authorisation, and Restriction of Chemicals) regulatory

framework, we published the chemical substances in our products

at ASUS REACH website at

http://csr.asus.com/english/index.aspx

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

• Thisdevicemaynotcauseharmfulinterference.

• Thisdevicemustacceptanyinterferencereceived,including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the

limits for a class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

113

Prohibition of Co-location

This device and its antenna(s) must not be co-located or operating

in conjunction with any other antenna or transmitter

CAUTION: Any changes or modiﬁcations not expressly approved by

the party responsible for compliance could void the user’s authority to

operate the equipment.

IMPORTANT! This device within the 5.15 ~ 5.25 GHz is restricted to

indoor operations to reduce any potential for harmful interference to

co-channel MSS operations.

against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment oﬀ and on, the user

is encouraged to try to correct the interference by one or more of

the following measures:

• Reorientorrelocatethereceivingantenna.

• Increasetheseparationbetweentheequipmentandreceiver.

• Connecttheequipmentintoanoutletonacircuitdierent

from that to which the receiver is connected.

• Consultthedealeroranexperiencedradio/TVtechnicianfor

help.

114

Safety Information

To maintain compliance with FCC’s RF exposure guidelines, this

equipment should be installed and operated with minimum

distance 20cm between the radiator and your body. Use on the

supplied antenna.

Declaration of Conformity for R&TTE directive 1999/5/EC

Essential requirements – Article 3

Protection requirements for health and safety – Article 3.1a

Testing for electric safety according to EN 60950-1 has been

conducted. These are considered relevant and suﬃcient.

Protection requirements for electromagnetic compatibility

– Article 3.1b

Testing for electromagnetic compatibility according to EN

301 489-1 and EN 301 489-17 has been conducted. These are

considered relevant and suﬃcient.

Eﬀective use of the radio spectrum – Article 3.2

Testing for radio test suites according to EN 300 328 & EN 301

893 have been conducted. These are considered relevant and

suﬃcient.

Operate the device in 5150-5250 MHz frequency band for indoor

use only.

CE Mark Warning

This is a Class B product, in a domestic environment, this product

may cause radio interference, in which case the user may be

required to take adequate measures.

This equipment may be operated in AT, BE, CY, CZ, DK, EE, FI, FR,

DE, GR, HU, IE, IT, LU, MT, NL, PL, PT, SK, SL, ES, SE, GB, IS, LI, NO, CH,

BG, RO, RT.

115

Canada, Industry Canada (IC) Notices

This Class B digital apparatus complies with Canadian ICES-003

and RSS-210.

Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept

any interference, including interference that may cause undesired

operation of the device.

Radio Frequency (RF) Exposure Information

The radiated output power of the ASUS Wireless Device is below

the Industry Canada (IC) radio frequency exposure limits. The

ASUS Wireless Device should be used in such a manner such

that the potential for human contact during normal operation is

minimized.

This device has been evaluated for and shown compliant with

the IC Speciﬁc Absorption Rate (“SAR”) limits when installed in

speciﬁc host products operated in portable exposure conditions

(antennas are less than 20 centimeters of a person’s body).

This device has been certiﬁed for use in Canada. Status of the

listing in the Industry Canada’s REL (Radio Equipment List) can be

found at the following web address: http://www.ic.gc.ca/app/sitt/

reltel/srch/nwRdSrch.do?lang=eng

Additional Canadian information on RF exposure also can be

found at the following web: http://www.ic.gc.ca/eic/site/smt-gst.

nsf/eng/sf08792.html

Canada, avis d’Industry Canada (IC)

Cet appareil numérique de classe B est conforme aux normes

116

canadiennes ICES-003 et RSS-210.

Son fonctionnement est soumis aux deux conditions suivantes:

(1) cet appareil ne doit pas causer d’interférence et (2) cet appareil

doit accepter toute interférence, notamment les interférences qui

peuvent a ecter son fonctionnement.

NCC 警語

經型式認證合格之低功率射頻電機，非經許可，公司、商號或

使用者均不得擅自變更頻率、加大功率或變更原設計之特性及

功能。低功率射頻電機之使用不得影響飛航安全及干擾合法通

信；經發現有干擾現象時，應立即停用，並改善至無干擾時方

得繼續使用。前項合法通信，指依電信法規定作業之無線電通

信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電

波輻射性電機設備之干擾。

電池波曝露量 MPE 標準值 1mWcm2，送測產品實測值

為：0.529 mWcm2。

GNU General Public License

Licensing information

This product includes copyrighted third-party software licensed

under the terms of the GNU General Public License. Please see The

GNU General Public License for the exact terms and conditions

of this license. We include a copy of the GPL with every CD

shipped with our product. All future ﬁrmware updates will also be

accompanied with their respective source code. Please visit our

web site for updated information. Note that we do not oﬀer direct

support for the distribution.

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

117

59 Temple Place, Suite 330, Boston, MA 02111-1307 USA

Everyone is permitted to copy and distribute verbatim copies of

this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your

freedom to share and change it. By contrast, the GNU General

Public License is intended to guarantee your freedom to share

and change free software--to make sure the software is free for all

its users. This General Public License applies to most of the Free

Software Foundation’s software and to any other program whose

authors commit to using it. (Some other Free Software Foundation

software is covered by the GNU Library General Public License

instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not

price. Our General Public Licenses are designed to make sure that

you have the freedom to distribute copies of free software (and

charge for this service if you wish), that you receive source code or

can get it if you want it, that you can change the software or use

pieces of it in new free programs; and that you know you can do

these things.

To protect your rights, we need to make restrictions that forbid

anyone to deny you these rights or to ask you to surrender the

rights. These restrictions translate to certain responsibilities for

you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether

gratis or for a fee, you must give the recipients all the rights that

you have. You must make sure that they, too, receive or can get

the source code. And you must show them these terms so they

know their rights.

118

We protect your rights with two steps: (1) copyright the software,

and (2) oﬀer you this license which gives you legal permission to

copy, distribute and/or modify the software.

Also, for each author’s protection and ours, we want to make

certain that everyone understands that there is no warranty for

this free software. If the software is modiﬁed by someone else and

passed on, we want its recipients to know that what they have is

not the original, so that any problems introduced by others will

not reﬂect on the original authors’ reputations.

Finally, any free program is threatened constantly by software

patents. We wish to avoid the danger that redistributors of a free

program will individually obtain patent licenses, in eﬀect making

the program proprietary. To prevent this, we have made it clear

that any patent must be licensed for everyone’s free use or not

licensed at all.

The precise terms and conditions for copying, distribution and

modiﬁcation follow.

Terms & conditions for copying, distribution, & modiﬁcation

0. This License applies to any program or other work which

contains a notice placed by the copyright holder saying it may

be distributed under the terms of this General Public License.

The “Program”, below, refers to any such program or work, and

a “work based on the Program” means either the Program or

any derivative work under copyright law: that is to say, a work

containing the Program or a portion of it, either verbatim or

with modiﬁcations and/or translated into another language.

(Hereinafter, translation is included without limitation in the

term “modiﬁcation”.) Each licensee is addressed as “you”.

Activities other than copying, distribution and modiﬁcation are

not covered by this License; they are outside its scope. The act

119

of running the Program is not restricted, and the output from

the Program is covered only if its contents constitute a work

based on the Program (independent of having been made by

running the Program). Whether that is true depends on what

the Program does.

1. You may copy and distribute verbatim copies of the Program’s

source code as you receive it, in any medium, provided that

you conspicuously and appropriately publish on each copy

an appropriate copyright notice and disclaimer of warranty;

keep intact all the notices that refer to this License and to the

absence of any warranty; and give any other recipients of the

Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a

copy, and you may at your option oﬀer warranty protection in

exchange for a fee.

2. You may modify your copy or copies of the Program or any

portion of it, thus forming a work based on the Program, and

copy and distribute such modiﬁcations or work under the

terms of Section 1 above, provided that you also meet all of

these conditions:

a) You must cause the modiﬁed ﬁles to carry prominent

notices stating that you changed the ﬁles and the date of any

change.

b) You must cause any work that you distribute or publish, that

in whole or in part contains or is derived from the Program or

any part thereof, to be licensed as a whole at no charge to all

third parties under the terms of this License.

c) If the modiﬁed program normally reads commands

interactively when run, you must cause it, when started

running for such interactive use in the most ordinary way, to

print or display an announcement including an appropriate

else, saying that you provide a warranty) and that users may

redistribute

120

the program under these conditions, and telling the user how

to view a copy of this License. (Exception: if the Program itself is

interactive but does not normally print such an announcement,

your work based on the Program is not required to print an

announcement.)

These requirements apply to the modiﬁed work as a whole.

If identiﬁable sections of that work are not derived from the

Program, and can be reasonably considered independent and

separate works in themselves, then this License, and its terms,

do not apply to those sections when you distribute them as

separate works. But when you distribute the same sections

as part of a whole which is a work based on the Program, the

distribution of the whole must be on the terms of this License,

whose permissions for other licensees extend to the entire

whole, and thus to each and every part regardless of who

wrote it.

Thus, it is not the intent of this section to claim rights or contest

your rights to work written entirely by you; rather, the intent is

to exercise the right to control the distribution of derivative or

collective works based on the Program.

In addition, mere aggregation of another work not based on

the Program with the Program (or with a work based on the

Program) on a volume of a storage or distribution medium

does not bring the other work under the scope of this License.

3. You may copy and distribute the Program (or a work based on

it, under Section 2) in object code or executable form under the

terms of Sections 1 and 2 above provided that you also do one

of the following:

a) Accompany it with the complete corresponding machine-

readable source code, which must be distributed under the

terms of Sections 1 and 2 above on a medium customarily used

for software interchange; or,

b) Accompany it with a written oﬀer, valid for at least three

years, to give any third party, for a charge no more than your

121

cost of physically performing source distribution, a complete

machine-readable copy of the corresponding source code, to

be distributed under the terms of Sections 1 and 2 above on a

medium customarily used for software interchange; or,

c) Accompany it with the information you received as to the oﬀer

to distribute corresponding source code. (This alternative is

allowed only for noncommercial distribution and only if you

received the program in object code or executable form with

such an oﬀer, in accord with Subsection b above.)

The source code for a work means the preferred form of

the work for making modiﬁcations to it. For an executable

work, complete source code means all the source code for all

modules it contains, plus any associated interface deﬁnition

ﬁles, plus the scripts used to control compilation and

installation of the executable. However, as a special exception,

the source code distributed need not include anything that

is normally distributed (in either source or binary form) with

the major components (compiler, kernel, and so on) of the

operating system on which the executable runs, unless that

component itself accompanies the executable.

If distribution of executable or object code is made by

oﬀering access to copy from a designated place, then oﬀering

equivalent access to copy the source code from the same place

counts as distribution of the source code, even though third

parties are not compelled to copy the source along with the

object code.

4. You may not copy, modify, sublicense, or distribute the

Program except as expressly provided under this License. Any

attempt otherwise to copy, modify, sublicense or distribute

the Program is void, and will automatically terminate your

rights under this License. However, parties who have received

copies, or rights, from you under this License will not have

their licenses terminated so long as such parties remain in full

compliance.

5. You are not required to accept this License, since you have

not signed it. However, nothing else grants you permission to

modify or distribute the Program or its derivative works. These

actions are prohibited by law if you do not accept this License.

122

Therefore, by modifying or distributing the Program (or any

work based on the Program), you indicate your acceptance

of this License to do so, and all its terms and conditions for

copying, distributing or modifying the Program or works based

on it.

6. Each time you redistribute the Program (or any work based

on the Program), the recipient automatically receives a license

from the original licensor to copy, distribute or modify the

Program subject to these terms and conditions. You may not

impose any further restrictions on the recipients’ exercise of

the rights granted herein. You are not responsible for enforcing

compliance by third parties to this License.

7. If, as a consequence of a court judgment or allegation of patent

infringement or for any other reason (not limited to patent

issues), conditions are imposed on you (whether by court order,

agreement or otherwise) that contradict the conditions of this

License, they do not excuse you from the conditions of this

License. If you cannot distribute so as to satisfy simultaneously

your obligations under this License and any other pertinent

obligations, then as a consequence you may not distribute

the Program at all. For example, if a patent license would not

permit royalty-free redistribution of the Program by all those

who receive copies directly or indirectly through you, then the

only way you could satisfy both it and this License would be to

refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable

under any particular circumstance, the balance of the section

is intended to apply and the section as a whole is intended to

apply in other circumstances.

It is not the purpose of this section to induce you to infringe

any patents or other property right claims or to contest

validity of any such claims; this section has the sole purpose

of protecting the integrity of the free software distribution

system, which is implemented by public license practices.

Many people have made generous contributions to the wide

range of software distributed through that system in reliance

123

on consistent application of that system; it is up to the author/

donor to decide if he or she is willing to distribute software

through any other system and a licensee cannot impose that

choice.

This section is intended to make thoroughly clear what is

believed to be a consequence of the rest of this License.

8. If the distribution and/or use of the Program is restricted in

certain countries either by patents or by copyrighted interfaces,

the original copyright holder who places the Program under

this License may add an explicit geographical distribution

limitation excluding those countries, so that distribution is

permitted only in or among countries not thus excluded. In

such case, this License incorporates the limitation as if written

in the body of this License.

9. The Free Software Foundation may publish revised and/or new

versions of the General Public License from time to time. Such

new versions will be similar in spirit to the present version, but

may diﬀer in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the

Program speciﬁes a version number of this License which

applies to it and “any later version”, you have the option of

following the terms and conditions either of that version or of

any later version published by the Free Software Foundation. If

the Program does not specify a version number of this License,

you may choose any version ever published by the Free

Software Foundation.

10. If you wish to incorporate parts of the Program into other free

programs whose distribution conditions are diﬀerent, write to

the author to ask for permission.

For software which is copyrighted by the Free Software

Foundation, write to the Free Software Foundation; we

sometimes make exceptions for this. Our decision will be

guided by the two goals of preserving the free status of all

derivatives of our free software and of promoting the sharing

and reuse of software generally.

124

NO WARRANTY

11 BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,

THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT

PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE

STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER

PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY

OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,

BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF

THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE

DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY

SERVICING, REPAIR OR CORRECTION.

12 IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR

AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR

ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE

THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR

DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL

OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE

OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT

LIMITED TO LOSS OF DATA OR DATA BEING RENDERED

INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES

OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER

PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

125

For Turkey only

AEEE Yönetmeliğine Uygundur.

Authorised distributors in Turkey:

BOGAZICI BIL GISAYAR SAN. VE TIC. A.S.

Tel. No.: +90 212 3311000

Address: AYAZAGA MAH. KEMERBURGAZ CAD. NO.10

AYAZAGA/ISTANBUL

CIZGI Elektronik San. Tic. Ltd. Sti.

Tel. No.: +90 212 3567070

Address: CEMAL SURURI CD. HALIM MERIC IS MERKEZI

No: 15/C D:5-6 34394 MECIDIYEKOY/

ISTANBUL

KOYUNCU ELEKTRONiK BiLGi iSLEM SiST. SAN. VE DIS TIC.

A.S.

Tel. No.: +90 216 5288888

Address: EMEK MAH.ORDU CAD. NO:18, SARIGAZi,

SANCAKTEPE ISTANBUL

126

ASUS Contact information

ASUSTeK COMPUTER INC. (Asia Paciﬁc)

Address 15Li-TeRoad,Peitou,Taipei,Taiwan11259

Website www.asus.com.tw

Technical Support

Telephone +886228943447

SupportFax +886228907698

Online support support.asus.com

ASUS COMPUTER INTERNATIONAL (America)

Address 800 Corporate Way, Fremont, CA 94539, USA

Telephone +15107393777

Fax +15106084555

Website usa.asus.com

Online support support.asus.com

ASUS COMPUTER GmbH (Germany and Austria)

Address HarkortStr.21-23,D-40880Ratingen,Germany

SupportFax +49-2102-959931

Website asus.com/de

Online contact eu-rma.asus.com/sales

Technical Support

Telephone(Component)   +49-2102-5789555

Telephone Germany

(System/Notebook/Eee/LCD)  +49-2102-5789557

Telephone Austria

(System/Notebook/Eee/LCD)  +43-820-240513

SupportFax    +49-2102-959911

Online support support.asus.com

127

Networks Global Hotline Information

Region Country Hotline Number Service Hours

Europe

Cyprus 800-92491 09:00-13:00 ;

14:00-18:00 Mon-Fri

France 0033-170949400 09:00-18:00 Mon-Fri

Germany

0049-1805010920

09:00-18:00 Mon-Fri

10:00-17:00 Mon-Fri

0049-1805010923

(component support)

0049-2102959911 ( Fax )

Hungary 0036-15054561 09:00-17:30 Mon-Fri

Italy 199-400089 09:00-13:00 ;

14:00-18:00 Mon-Fri

Greece 00800-44142044 09:00-13:00 ;

14:00-18:00 Mon-Fri

Austria 0043-820240513 09:00-18:00 Mon-Fri

Netherlands/

Luxembourg 0031-591570290 09:00-17:00 Mon-Fri

Belgium 0032-78150231 09:00-17:00 Mon-Fri

Norway 0047-2316-2682 09:00-18:00 Mon-Fri

Sweden 0046-858769407 09:00-18:00 Mon-Fri

Finland 00358-969379690 10:00-19:00 Mon-Fri

Denmark 0045-38322943 09:00-18:00 Mon-Fri

Poland 0048-225718040 08:30-17:30 Mon-Fri

Spain 0034-902889688 09:00-18:00 Mon-Fri

Portugal 00351-707500310 09:00-18:00 Mon-Fri

Slovak Republic 00421-232162621 08:00-17:00 Mon-Fri

Czech Republic 00420-596766888 08:00-17:00 Mon-Fri

Switzerland-German 0041-848111010 09:00-18:00 Mon-Fri

Switzerland-French 0041-848111014 09:00-18:00 Mon-Fri

Switzerland-Italian 0041-848111012 09:00-18:00 Mon-Fri

United Kingdom 0044-81442265548 09:00-17:00 Mon-Fri

Ireland 0035-31890719918 09:00-17:00 Mon-Fri

Russia and CIS 008-800-100-ASUS 09:00-18:00 Mon-Fri

Ukraine 0038-0445457727 09:00-18:00 Mon-Fri

128

Networks Global Hotline Information

Region Country Hotline Numbers Service Hours

Asia-Paciﬁc

Australia 1300-278788 09:00-18:00 Mon-Fri

New Zealand 0800-278788 09:00-18:00 Mon-Fri

Japan 0800-1232787 09:00-18:00 Mon-Fri

09:00-17:00 Sat-Sun

0081-570783886

( Non-Toll Free )

09:00-18:00 Mon-Fri

09:00-17:00 Sat-Sun

Korea 0082-215666868 09:30-17:00 Mon-Fri

Thailand 0066-24011717 09:00-18:00 Mon-Fri

1800-8525201

Singapore 0065-64157917 11:00-19:00 Mon-Fri

0065-67203835 11:00-19:00 Mon-Fri

( Repair Status Only ) 11:00-13:00 Sat

Malaysia 0060-320535077 10:00-19:00 Mon-Fri

Philippine 1800-18550163 09:00-18:00 Mon-Fri

India 1800-2090365 09:00-18:00 Mon-Sat

India(WL/NW) 09:00-21:00 Mon-Sun

Indonesia 0062-2129495000 09:30-17:00 Mon-Fri

500128 (Local Only) 9:30 – 12:00 Sat

Vietnam 1900-555581 08:00-12:00

13:30-17:30 Mon-Sat

Hong Kong 00852-35824770 10:00-19:00 Mon-Sat

Americas

USA 1-812-282-2787 8:30-12:00 EST Mon-Fri

Canada 9:00-18:00 EST Sat-Sun

Mexico 001-8008367847 08:00-20:00 CST Mon-Fri

08:00-15:00 CST Sat

129

NOTE: For more information, visit the ASUS support site at:

http://support.asus.com

Manufacturer: ASUSTeK Computer Inc.

Tel: +886-2-2894-3447

Address: 4F, No. 150, LI-TE RD., PEITOU,

TAIPEI 112, TAIWAN

Authorised

representative

in Europe:

ASUS Computer GmbH

Address: HARKORT STR. 21-23, 40880

RATINGEN, GERMANY

Region Country Hotline Numbers Service Hours

Middle

East +

Africa

Egypt 800-2787349 09:00-18:00 Sun-Thu

Saudi Arabia 800-1212787 09:00-18:00 Sat-Wed

UAE 00971-42958941 09:00-18:00 Sun-Thu

Turkey 0090-2165243000 09:00-18:00 Mon-Fri

South Africa 0861-278772 08:00-17:00 Mon-Fri

Israel *6557/00972-39142800 08:00-17:00 Sun-Thu

*9770/00972-35598555 08:30-17:30 Sun-Thu

Balkan

Countries

Romania 0040-213301786 09:00-18:30 Mon-Fri

Bosnia

Herzegovina 00387-33773163 09:00-17:00 Mon-Fri

Bulgaria 00359-70014411 09:30-18:30 Mon-Fri

00359-29889170 09:30-18:00 Mon-Fri

Croatia 00385-16401111 09:00-17:00 Mon-Fri

Montenegro 00382-20608251 09:00-17:00 Mon-Fri

Serbia 00381-112070677 09:00-17:00 Mon-Fri

Slovenia 00368-59045400 08:00-16:00 Mon-Fri

00368-59045401

Estonia 00372-6671796 09:00-18:00 Mon-Fri

Latvia 00371-67408838 09:00-18:00 Mon-Fri

Lithuania-Kaunas 00370-37329000 09:00-18:00 Mon-Fri

Lithuania-Vilnius 00370-522101160 09:00-18:00 Mon-Fri

Networks Global Hotline Information

Table of Contents

ASUS RT-AC1900P User Manual

Related Manuals