ASUS TS100-E10-PI4 User Manual

Displayed below is the user manual for TS100-E10-PI4 by ASUS which is a product in the Servers category. This manual has pages.

Related Manuals

ASUS ASUS Rampage IV GENE Manual

ASUS ASUS X99-DELUXE II Manual

ASUS ASUS MCI-10G/X550-2T Manual

ASUS UX435EAL-KC096T Manual

ASUS PN62S-B3519ZD Manual

ASUS VE228H Manual

ASUS RS700DA-E6/PS4 Manual

ASUS PCE-N15 Manual

Pedestal Server

TS100-E10-PI4

User Guide

E17464

Revised Edition V4

November 2020

No part of this manual, including the products and software described in it, may be reproduced, transmitted,

transcribed, stored in a retrieval system, or translated into any language in any form or by any means,

except documentation kept by the purchaser for backup purposes, without the express written permission

of ASUSTeK COMPUTER INC. (“ASUS”).

ASUS provides this manual “as is” without warranty of any kind, either express or implied, including but not

limited to the implied warranties or conditions of merchantability or tness for a particular purpose. In no

event shall ASUS, its directors, ofcers, employees, or agents be liable for any indirect, special, incidental,

or consequential damages (including damages for loss of prots, loss of business, loss of use or data,

interruption of business and the like), even if ASUS has been advised of the possibility of such damages

arising from any defect or error in this manual or product.

Specications and information contained in this manual are furnished for informational use only, and are

subject to change at any time without notice, and should not be construed as a commitment by ASUS.

ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual,

including the products and software described in it.

Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless

such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the

product is defaced or missing.

Products and corporate names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies, and are used only for identication or explanation and to the

owners’ benet, without intent to infringe.

iii

Contents

Safety information ..................................................................................................... vii

About this guide ....................................................................................................... viii

Chapter 1: Product Introduction

1.1 System package contents ......................................................................... 1-2

1.2 Serial number label .................................................................................... 1-2

1.3 Systemspecications ............................................................................... 1-3

1.4 Front panel features...................................................................................1-5

1.5 Rear panel features .................................................................................... 1-6

1.6 Internal features ......................................................................................... 1-7

1.7 LED information ......................................................................................... 1-8

1.7.1 Front panel LEDs ........................................................................ 1-8

1.7.2 Rear panel LEDs ......................................................................... 1-8

Chapter 2: Hardware Information

2.1 Chassis cover ............................................................................................. 2-2

2.1.1 Removing the side cover............................................................. 2-2

2.2 Central Processing Unit (CPU) ................................................................. 2-4

2.2.1 Installing the CPU ....................................................................... 2-4

2.2.2 Installing the CPU heatsink and fan assembly ............................ 2-7

2.2.3 Uninstalling the CPU heatsink and fan........................................ 2-8

2.3 System memory ......................................................................................... 2-9

2.3.1 Overview ..................................................................................... 2-9

2.3.2 Memory Congurations ............................................................... 2-9

2.3.3 Installing a DIMM on a single clip DIMM socket........................ 2-10

2.4 Front panel cover ..................................................................................... 2-11

2.4.1 Removing the front panel cover ................................................ 2-11

2.5 5.25-inch drives ........................................................................................ 2-12

2.6 Hard disk drives (HDD) ............................................................................ 2-14

2.7 Expansion cards ...................................................................................... 2-18

2.7.1 Installing an expansion card......................................................2-18

2.7.2 Conguring an expansion card ................................................. 2-20

2.8 System fan ................................................................................................ 2-21

2.9 Cable connections ................................................................................... 2-22

Contents

Chapter 3: Motherboard Information

3.1 Motherboard layout....................................................................................3-2

3.2 Jumpers ...................................................................................................... 3-4

3.3 Onboard LEDs ............................................................................................ 3-7

3.4 Internal connectors .................................................................................... 3-9

Chapter 4: BIOS Setup

4.1 Managing and updating your BIOS .......................................................... 4-2

4.1.1 ASUS CrashFree BIOS 3 utility................................................... 4-2

4.1.2 ASUS EZ Flash Utility ................................................................. 4-3

4.1.3 BUPDATER utility ....................................................................... 4-4

4.2 BIOS setup program .................................................................................. 4-6

4.2.1 BIOS menu screen ...................................................................... 4-7

4.2.2 Menu bar ..................................................................................... 4-7

4.2.3 Menu items..................................................................................4-8

4.2.4 Submenu items ........................................................................... 4-8

4.2.5 Navigation keys ........................................................................... 4-8

4.2.6 General help................................................................................4-8

4.2.7 Conguration elds ..................................................................... 4-8

4.2.8 Pop-up window............................................................................4-8

4.2.9 Scroll bar ..................................................................................... 4-8

4.3 Main menu .................................................................................................. 4-9

4.4 Advanced menu ....................................................................................... 4-10

4.4.1 CPU Conguration .................................................................... 4-11

4.4.2 Power & Performance ............................................................... 4-13

4.4.3 Server ME Conguration ........................................................... 4-14

4.4.4 Trusted Computing....................................................................4-15

4.4.5 APM Conguration .................................................................... 4-15

4.4.6 Runtime Error Logging Settings ................................................ 4-16

4.4.7 Onboard LAN Conguration ...................................................... 4-16

4.4.8 Serial Port Console Redirection ................................................ 4-17

4.4.9 Intel TXT Information.................................................................4-19

4.4.10 PCI Subsystem Settings ........................................................... 4-20

4.4.11 USB Conguration .................................................................... 4-20

4.4.12 Network Stack Conguration..................................................... 4-22

4.4.13 CSM Conguration .................................................................... 4-23

Contents

4.4.14 NVMe Conguration .................................................................. 4-24

4.4.15 WHEA Conguration ................................................................. 4-24

4.4.16 iSCSI Conguration .................................................................. 4-25

4.4.17 Tls Auth Conguration............................................................... 4-25

4.5 Chipset menu ........................................................................................... 4-26

4.5.1 System Agent (SA) Conguration ............................................. 4-26

4.5.2 PCH-IO Conguration ............................................................... 4-29

4.6 Security menu .......................................................................................... 4-32

4.7 Boot menu ................................................................................................ 4-35

4.8 Monitor menu ........................................................................................... 4-37

4.9 Tool menu ................................................................................................. 4-38

4.10 Event Logs menu ..................................................................................... 4-38

4.10.1 Change Smbios Event Log Settings ......................................... 4-38

4.10.2 View Smbios Event Log ............................................................ 4-39

4.11 Save & Exit menu ..................................................................................... 4-40

Chapter5: RAIDConguration

5.1 Setting up RAID .......................................................................................... 5-2

5.1.1 RAID denitions .......................................................................... 5-2

5.1.2 Installing hard disk drives ............................................................ 5-3

5.1.3 Setting the RAID item in BIOS .................................................... 5-3

5.2 Intel® Rapid Storage Technology enterprise SATA Option

ROM Utility .................................................................................................. 5-4

5.2.1 Creating a RAID set .................................................................... 5-5

5.2.2 Deleting a RAID set.....................................................................5-7

5.2.3 Resetting disks to Non-RAID ...................................................... 5-8

5.2.4 Exiting the Intel® Rapid Storage Technology enterprise

SATA Option ROM utility............................................................. 5-9

5.2.5 Rebuilding the RAID....................................................................5-9

5.2.6 Setting the Boot array in the BIOS Setup Utility ........................ 5-11

5.3 Intel® Rapid Storage Technology enterprise (Windows) ...................... 5-12

5.3.1 Creating a RAID set .................................................................. 5-13

5.3.2 Changing a Volume Type..........................................................5-15

5.3.3 Deleting a volume ..................................................................... 5-16

5.3.4 Preferences ............................................................................... 5-17

Chapter 6: Driver Installation

6.1 RAID driver installation ............................................................................. 6-2

6.1.1 Creating a USB ash drive with RAID drive ................................ 6-2

6.1.2 Installing the RAID controller driver............................................. 6-2

6.2 Management applications and utilities installation ................................ 6-5

6.3 Running the Support DVD ......................................................................... 6-5

6.4 Installing the system drivers.....................................................................6-6

Appendix

P11C-X/AUDIO block diagram ............................................................................... A-2

Q-Code table ............................................................................................................ A-3

Notices .................................................................................................................... A-6

ASUS contact information ...................................................................................... A-9

vii

Safety information

Electrical Safety

• Before installing or removing signal cables, ensure that the power cables for the system

unit and all attached devices are unplugged.

• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet

before relocating the system.

• When adding or removing any additional devices to or from the system, ensure that the

power cables for the devices are unplugged before the signal cables are connected. If

possible, disconnect all power cables from the existing system before you add a device.

• If the power supply is broken, do not try to x it by yourself. Contact a qualied service

technician or your dealer.

Operation Safety

• Any mechanical operation on this server must be conducted by certied or experienced

engineers.

• Before operating the server, carefully read all the manuals included with the server

package.

• Before using the server, ensure all cables are correctly connected and the power cables

are not damaged. If any damage is detected, contact your dealer as soon as possible.

• To avoid short circuits, keep paper clips, screws, and staples away from connectors,

slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Place the server on a stable surface.

Lithium-Ion Battery Warning

CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with

the same or equivalent type recommended by the manufacturer. Dispose of used

batteries according to the manufacturer’s instructions.

Heavy System

CAUTION! This server system is heavy. Ask for assistance when moving or carrying

the system.

This product is equipped with a three-wire power cable and plug for the user’s safety. Use

the power cable with a properly grounded electrical outlet to avoid electrical shock.

CLASS 1 LASER PRODUCT

viii

About this guide

Audience

This user guide is intended for system integrators, and experienced users with at least basic

knowledge of conguring a server.

Contents

This guide contains the following parts:

1. Chapter 1: Product Introduction

This chapter describes the general features of the server, including sections on front

panel and rear panel specications.

2. Chapter 2: Hardware Information

This chapter lists the hardware setup procedures that you have to perform when

installing or removing system components.

3. Chapter 3: Motherboard Information

This chapter includes the motherboard layout and brief descriptions of the jumpers and

internal connectors.

4. Chapter 4: BIOS Setup

This chapter tells how to change system settings through the BIOS Setup menus and

describes the BIOS parameters.

5. Chapter5:RAIDConguration

This chapter provides instructions for setting up, creating and conguring RAID sets

using the available utilities.

6 Chapter 6: Driver Installation

This chapter provides instructions for installing the necessary drivers for different

system components.

Conventions

To ensure that you perform certain tasks properly, take note of the following symbols used

throughout this manual.

Typography

Bold text Indicates a menu or an item to select.

Italics

Used to emphasize a word or a phrase.

<Key> Keys enclosed in the less-than and greater-than

sign means that you must press the enclosed key.

Example: <Enter> means that you must press

the Enter or Return key.

<Key1>+<Key2>+<Key3> If you must press two or more keys simultaneously,

the key names are linked with a plus sign (+).

Example: <Ctrl>+<Alt>+<Del>

Command Means that you must type the command

exactly as shown, then supply the required

item or value enclosed in brackets.

Example: At the DOS prompt, type the

command line: format A:/S

DANGER/WARNING: Information to prevent injury to yourself when

trying to complete a task.

CAUTION: Information to prevent damage to the components when

trying to complete a task.

NOTE: Tips and additional information to help you complete a task.

IMPORTANT: Instructions that you MUST follow to complete a task.

References

Refer to the following sources for additional information, and for product and software

updates.

1. ASUS Control Center (ACC) user guide

This manual tells how to set up and use the proprietary ASUS server management

utility.

2. ASUS websites

The ASUS websites worldwide provide updated information for all ASUS hardware and

software products. Refer to the ASUS contact information.

This chapter describes the general features of the server,

including sections on front panel and rear panel specications.

Product Introduction

Chapter 1: Product Introduction

1-2

If any of the above items is damaged or missing, contact your retailer.

1.1 System package contents

Check your system package for the following items.

1.2 Serial number label

Before requesting support from the ASUS Technical Support team, you must take note of

the product’s serial number containing 12 characters such as xxS0xxxxxxxx shown as the

gure below. With the correct serial number of the product, ASUS Technical Support team

members can then offer a quicker and satisfying solution to your problems.

xxS0xxxxxxxx

TS100-E10-PI4

Model Name TS100-E10-PI4

Accessories 1 x TS100-E10-PI4 Support CD

1 x AC Power Cable

1 x COM port Cable

Optional Items Smart Card Reader

Anti-Virus CD pack

DVD-RW

Keyboard and mouse

ASUS TS100-E10-PI4 1-3

1.3 Systemspecications

The ASUS TS100-E10-PI4 is a pedestal server. The server supports LGA1151 Intel® Xeon®

Processor E Family (Coffee Lake) and Intel® 8th/9th Generation Core™ i3 Processors.

Model Name TS100-E10-PI4

Processor Support

1 x Socket LGA1151

Intel® Xeon® processor E-21xx/E-22xx product family

Intel® 8th/9th Generation Core™ i3 processors, Intel® Pentium™

and Celeron™ Processors (Coffee Lake)

* Refer to ASUS server AVL for the latest update

Core Logic Intel® C242 Chipset

Memory

Total Slots 4 (2-Channels)

Capacity Maximum up to 128GB (UDIMM)

Memory Type DDR4 2666 / 2400 ECC / non-ECC UDIMM

* Refer to ASUS server AVL for the latest update

Memory Size 32GB, 16GB, 8GB, 4GB (UDIMM)

* Refer to ASUS server AVL for the latest update

Expansion

Slots

Total PCI/PCI-X/

PCI-E/PIKE Slots

Slot Type

1 x PCI-E x16 (Gen3 x16 Link)

1 x PCI-E x8 (Gen3 x4 Link)

2 x PCI

Disk

Controller

SATA Controller

Intel® C242

6 x SATA 6Gb/s ports with 2 x M.2 (NGFF 22110/2280/2260/2242,

gray SATA port will be disables when M.2 is in SATA mode)*

Intel® RSTe (Windows & Linux)

(Supports software RAID 0, 1, 10 & 5)

* One supports both SATA 6Gb/s & PCI-E Gen3 x2 link, the other is

SATA 6Gb/s only.

SAS Controller Optional:

ASUS PIKE II 3008-8i 8-port SAS 12G RAID card

Storage

Bays

I = internal

A or S will be hot-

swappable

3 x Internal 3.5” (or 2 x 2.5” optional cage) drive bays*

1 x Internal 2.5” drive bay

1 x Optional internal 5.25” to 3.5”/2.5” drive cage

2 x M.2 (NGFF 22110/2280/2260/2242)

* Supports only 1 drive when add-on card over 9.5” is installed on x16

link slot

Networking LAN 1 x Intel® I210-AT Gigabit LAN + 1 x Intel® I219-LM Gigabit LAN

Graphic VGA Aspeed AST2510 64MB

Auxiliary Storage Device Bay

(Floppy / Optical Drive)

2 x 5.25” media bays

Options: No Device / DVD-RW / DVD ROM

(continued on the next page)

Chapter 1: Product Introduction

1-4

*Specicationsaresubjecttochangewithoutnotice.

Model Name TS100-E10-PI4

Front I/O Ports

2 x USB 3.0 ports

2 x USB 2.0 ports

1 x Headphone port

1 x Microphone port

Rear I/O Ports

2 x USB 3.1 ports

2 x USB 3.0 ports

2 x USB 2.0 ports

1 x VGA Port (onboard Aspeed AST2510)

2 x LAN Ports

3 x Audio Jacks (Realtek® ALC887-VD2 8-Channel High Denition

Audio CODEC)

1 x PS/2 Keyboard/ Mouse Port

Switch/LED

Front Switch/LED:

1 x Power switch

1 x Power LED

1 x Reset switch

1 x HDD Access LED

OS Support

Windows® Server 2016

RedHat® Enterprise Linux

SuSE® Linux Enterprise Server

CentOS

* PleasendthelatestOSsupportfromhttp://www.asus.com/

Management

Solution Software ASUS Control Center

Regulatory Compliance BSMI, CE, RCM, FCC, CCC (Class B)

Dimension (HH x WW x DD) 423mm x 190mm x 435mm

(16.65” x 7.48” x 17.1”)

Net Weight Kg

(Estimated) 12.77 Kg

Gross Weight Kg

(Estimated) 15.74 Kg

Power Supply

(following different

congurationbyregion)

500W 80PLUS Single Power Supply, Gold

(Rating: 100-240Vac, 7-3.5A, 50/60Hz, Class I)

300W 80PLUS Single Power Supply, Bronze

(Rating: 100-127/220-240Vac, 6/3A, 60-50Hz, Class I)

450W/550W Single Power Supply, Gold

(Rating: 100-240Vac, 50-60Hz, 9-4.5A)

Environment

Operating temperature: 10°C ~ 35°C

Non operating temperature: -40°C ~ 70°C

Non operating humidity: 20% ~ 90% ( Non condensing)

ASUS TS100-E10-PI4 1-5

1.4 Front panel features

The TS100-E10-PI4 Pedestal server features a simple yet stylish front panel design. The

power and reset buttons, LED indicators, optical drive, and USB ports are all conveniently

located at the front panel for easy access.

SD/MMC/MS

Smart Card

Refer to the Front panel LEDs section for the LED descriptions.

Optical Drive (Optional)

Empty 5.25-inch bay

HDD access LED

Reset button

Microphone port

Headphone port

Power button

USB 2.0 ports

USB 3.0 ports

Power LED

Card reader (optional)

Chapter 1: Product Introduction

1-6

1.5 Rear panel features

The rear panel includes a slot for the motherboard rear I/O ports, expansion slots, a vent for

the system fan, and the power supply module.

Single power supply

Power connector

Expansion slots

PCI-E latch

USB 2.0 ports

VGA port

Gigabit LAN port 1 120 mm x 120 mm

system fan vents

PS/2 keyboard /

mouse port

Gigabit LAN port 2

USB 3.0 ports

USB 3.1 ports

Audio ports

ASUS TS100-E10-PI4 1-7

1.6 Internal features

The TS100-E10-PI4 Pedestal server system includes the basic components as shown:

The barebone server does not include a oppy disk drive. If you need to use a oppy disk,

connect the USB oppy disk drive to any of the USB ports on the front or rear panel.

WARNING

HAZARDOUS MOVING PARTS

KEEP FINGERS AND OTHER BODY PARTS AWAY

Turn off the system power and detach the power supply before removing or replacing any

system component.

1. Power supply unit

2. 120 mm x 120 mm system fan

3. ASUS P11C-X/AUDIO Board

4. Expansion card locks

5. Optical drive (Optional)

6. 1 x 5.25-inch drive bay

7. Front I/O board (hidden)

8. 3 x 3.5-inch Internal HDD bays

9. 1 x 2.5-inch Internal HDD/SSD bay

Chapter 1: Product Introduction

1-8

1.7 LED information

1.7.1 Front panel LEDs

LED Icon Display status Description

Power LED ON System power ON

HDD Access LED OFF

Blinking

No activity

Read/write data into the HDD

HDD Access LED

Power LED

1.7.2 Rear panel LEDs

LAN port

SPEED

LED

ACT/LINK

LED

Activity/Link LED Speed LED

Status Description Status Description

OFF No link OFF 10 Mbps connection

GREEN Linked ORANGE 100 Mbps connection

BLINKING Data activity GREEN 1 Gbps connection

2-1

ASUS TS100-E10-PI4

Hardware Information

This chapter lists the hardware setup procedures that you have

to perform when installing system components. It includes

description of the jumpers and connectors on the motherboard.

Chapter 2: Hardware Information

2-2

2.1 Chassis cover

2.1.1 Removing the side cover

• Ensure that you unplug the power cord before removing the side cover.

• Takeextracarewhenremovingthesidecover.Keepyourngersfromcomponents

inside the chassis that can cause injury, such as the CPU fan, rear fan, and other

sharp-edged parts.

• The images of the barebone server shown in this section are for reference purposes

only and may not exactly match the model you purchase.

To remove the side cover:

1. Remove the two screws that secure the

side cover.

2. Press the side cover locks outward.

side cover locks

screws

2-3

ASUS TS100-E10-PI4

3. Slightly pull the side cover toward the

rear just enough to detach it from the

chassis.

4. Remove the cover and set it aside.

Chapter 2: Hardware Information

2-4

2.2.1 Installing the CPU

To install the CPU:

1. Locate the CPU socket on the motherboard.

Before installing the CPU, ensure that the socket box is facing toward you and the load

lever is on your right.

2.2 Central Processing Unit (CPU)

The motherboard comes with a surface mount LGA1151 socket designed for the Intel® Xeon®

Processor E Family (Coffee Lake) and Intel® 8th/9th Generation Core™ i3 Processors

• Ensure that all power cables are unplugged before installing the CPU.

• Upon purchase of the server system, ensure that the PnP cap is on the socket and

the socket contacts are not bent. Contact your retailer immediately if the PnP cap

is missing, or if you see any damage to the PnP cap/socket contacts/motherboard

components. ASUS will shoulder the cost of repair only if the damage is shipment/

transit-related.

• The product warranty does not cover damage to the socket contacts resulting from

incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP

cap.

2-5

ASUS TS100-E10-PI4

Do not remove the PnP cap yet from

the CPU socket. Doing so may bend

the pins of the socket.

Retention tab

Load lever

2. Press the load lever with your thumb

(A), then move it to the right (B) until it is

released from the retention tab.

3. Lift the load lever until the load plate is

completely lifted.

Load plate

4. Position the CPU above the socket,

ensuring that the gold triangle mark is

on the bottom-left corner of the socket,

thenttheCPUnotchestothesocket's

alignment keys.

TheCPUtsinonlyoneorientation.

DO NOT force the CPU into the

socket to prevent bending the pins on

the socket and damaging the CPU.

Gold

triangle

mark

CPU notches

Alignment

key

Alignment

key

Chapter 2: Hardware Information

2-6

5. Close the load plate (A), ensuring that

the front edge of the load plate slides

under the retention lock (B) then push

down the load lever (C).

Retention

lock

Load lever

6. Insert the load lever under the retention tab to remove the PnP cap from the CPU

socket.

Retention tab

Load lever

7. Apply some Thermal Interface Material

to the exposed area of the CPU that the

heatsink will be in contact with, ensuring

that it is evenly spread in a thin layer.

Some heatsinks come with pre-

applied Thermal Interface Material. If

so, skip this step.

The Thermal Interface Material is

toxic and inedible. DO NOT eat it. If

it gets into your eyes or touches your

skin, wash it off immediately and seek

professional medical help.

2-7

ASUS TS100-E10-PI4

2.2.2 Installing the CPU heatsink and fan assembly

To install the CPU heatsink and fan assembly

Chapter 2: Hardware Information

2-8

5. Connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN1.

DO NOT forget to connect the CPU fan connector! Hardware monitoring errors can occur if

you fail to plug this connector.

2.2.3 Uninstalling the CPU heatsink and fan

To uninstall the CPU heatsink and fan:

1. Disconnect the CPU fan cable from the

connector on the motherboard.

2. Rotate each fastener counterclockwise.

3. Pull up two fasteners at a time in a

diagonal sequence to disengage the

heatsink and fan assembly from the

motherboard.

4. Carefully remove the heatsink and fan assembly from the motherboard.

2-9

ASUS TS100-E10-PI4

2.3 System memory

2.3.1 Overview

The motherboard comes with four Double Data Rate 4 (DDR4) Dual Inline Memory Modules

(DIMM) sockets.

A DDR4 module is notched differently from a DDR, DDR2, or DDR3 module. DO NOT

install a DDR, DDR2, or DDR3 memory module to the DDR4 slot.

ThegureillustratesthelocationoftheDDR4DIMMsockets:

2.3.2 MemoryCongurations

You may install ECC / non-ECC DDR4 DIMMs into the DIMM sockets using the memory

congurationsinthissection.

UDIMM

DIMM Slot Per

Channel

DIMMPopulated

per Channel DIMM Type Speed

2 1 ECC / non-ECC 2666/2400

2 2 ECC / non-ECC 2666/2400

• Always install DIMMs with the same CAS latency. For optimum compatibility, it is

recommended that you obtain memory modules from the same vendor.

• Start installing the DIMMs in slots A2 and B2 (Blue).

Chapter 2: Hardware Information

2-10

2.3.3 Installing a DIMM on a single clip DIMM socket

Ensure to unplug the power supply before adding or removing DIMMs or other system

components. Failure to do so may cause severe damage to both the motherboard and the

components.

3. Hold the DIMM by both of its ends

then insert the DIMM vertically into the

socket. Apply force to both ends of the

DIMM simultaneously until the retaining

clip snaps back into place and the

DIMM cannot be pushed in any further

to ensure proper sitting of the DIMM.

Locked Retaining Clip

1. Unlock a DIMM socket by pressing the

retaining clip outward.

2. Align a DIMM on the socket such that

the notch on the DIMM matches the

DIMM slot key on the socket.

Unlocked retaining clip

DIMM notch

DIMM slot key

1. Press the retaining clip outward to

unlock the DIMM.

2. Remove the DIMM from the socket.

Removing a DIMM from a single clip DIMM socket

SupporttheDIMMlightlywithyourngerswhenpressingtheretainingclips.TheDIMM

mightgetdamagedwhenitipsoutwithextraforce.

Always insert the DIMM into the socket vertically to prevent DIMM notch damage.

ADIMMiskeyedwithanotchsothatittsinonlyonedirection.DONOTforceaDIMMinto

a socket in the wrong direction to avoid damaging the DIMM.

2-11

ASUS TS100-E10-PI4

2.4 Front panel cover

Beforeyoucaninstalla5.25-inchdrive,youshouldrstremovethefrontpanelcover.

Ensure to unplug the power cable before installing or removing any system components.

Failure to do so may cause damage to the motherboard and other system components!

2.4.1 Removing the front panel cover

To remove the front panel cover:

1. Locate the front panel assembly lock then slide it outward to unlock the latches that

secures the front panel cover to the chassis.

2. Remove the front panel assembly from the chassis and set it aside.

assembly lock

Front panel assembly

Chapter 2: Hardware Information

2-12

2.5 5.25-inch drives

Installing a 5.25-inch drive

To install a 5.25-inch drive:

1. Remove the front panel cover. Refer to

the Removing the front panel cover

section for more information.

2. Pull the bay locks outward.

3. Remove the metal cover of the bay

you intend to use.

Take extra care when removing the

metal cover. Use tools such as a

screw driver to bend and remove

the metal cover to avoid physical

injury.

This system comes with three 5.25-inch drive

bays located on the upper front section of the

chassis.

If your system came with an optical

drive, the optical drive occupies the

topmost bay (1). The lower bays (2

and 3) are available for additional

5.25-inchoptical,zip,oroppydisk

drives.

bay locks

screw driver

metal cover

2-13

ASUS TS100-E10-PI4

7. Connect the SATA cable to the SATA

connector of the drive.

8. Connect a SATA power cable from the

power supply to the power connector of

the drive.

9. Reinstall the front panel cover.

4. Prepare the 5.25-inch drive.

5. Insert and carefully push the drive into

the bay until its screw holes align with

the holes on the bay.

6. Push the bay locks to secure the drive in

place.

bay locks

SATA cableSATA power cable

Chapter 2: Hardware Information

2-14

2.6 Hard disk drives (HDD)

The server system supports three (3) 3.5-inch Serial ATA hard disk drives via the hard disk

drive bays and one 2.5-inch HDD/SSD drive at the bottom of the HDD cage.

Installing 3.5-inch HDDs

To install 3.5-inch Serial ATA hard disk drives:

1. Remove the side cover of the chassis. Refer to the Removing the side cover section

for more information.

2. Prepare the 3.5-inch HDD and the bundled set of screws.

3. Locate the HDD cage lock, press the it up (A), then swing the HDD cage outwards (B)

until it clicks in place.

4. Align and insert the 3.5-inch HDD into

the drive bay ensuring that the screw

holes on the HDD matches the screw

holes on the HDD cage.

screw holes (HDD)

HDD cage lock

HDD cage

screw hole (HDD cage)

2-15

ASUS TS100-E10-PI4

5. Secure the 3.5-inch HDD to the HDD

cage using the bundled set of screws.

6. Swing the HDD cage inwards until it

clicks back into place.

7. Connect the SATA cable and SATA

power cable to the 3.5-inch HDD.

Chapter 2: Hardware Information

2-16

Installing 2.5-inch HDD/SSD

To install a 2.5-inch HDD/SSD:

1. Remove the side cover of the chassis. Refer to the Removing the side cover section

for more information.

2. Prepare the 2.5-inch HDD/SDD and the bundled set of screws.

3. Laythesystemonitssideonaatandstablesurface.

4. Locate the HDD cage lock, press it up (A), then swing the HDD cage outwards (B).

5. Align and insert the 2.5-inch HDD/SSD into the drive bay as shown. Push it all the way

until its screw holes align with the holes on the drive bay.

HDD cage lock

HDD cage

matching screw holes

2.5-inch HDD/SSD

2-17

ASUS TS100-E10-PI4

6. Secure the 2.5-inch HDD/SSD to

the HDD cage using the bundled

set of screws.

7. Swing the HDD cage inwards

until it clicks back into place.

8. Connect a SATA cable and a

SATA power cable to the 2.5-inch

HDD/SSD.

Chapter 2: Hardware Information

2-18

2.7 Expansion cards

The system has expansion slots on the rear panel that allows you to install expansion cards

or additional components.

Ensure to unplug the power cord before installing or removing expansion cards. Failure to

do so may cause severe damage to the motherboard and other system components!

Read the documentation of the expansion card and make the necessary hardware settings

for the card before installing them.

2.7.1 Installing an expansion card

To install an expansion card:

1. Laythesystemonitssideonaat,stablesurface.

2. Press the PCI-E latch (A), hold it by its edge then lift it towards the rear (B).

3. Remove the screw (A) that secures

the metal bracket to the chassis then

remove the metal bracket (B).

Metal bracket

PCI-E latch

Edge of the PCI-E latch

Screw

2-19

ASUS TS100-E10-PI4

4. Align and insert the expansion card into

the PCI-E slot.

5. Lift the PCI-E latch inwards until it clicks into place securing the expansion card to the

chassis.

6. (Optional) Replace the screw of the

metal bracket.

PCI-E slot

Expansion card

PCI-E latch

Chapter 2: Hardware Information

2-20

2.7.2 Conguringanexpansioncard

Afterinstallingtheexpansioncard,conguretheitbyadjustingthesoftwaresettings.

1. Turn on the system and change the necessary BIOS settings, if any. See Chapter 5 for

information on BIOS setup.

2. Assign an IRQ to the card. Refer to the following tables.

3. Install the software drivers for the expansion card.

StandardInterruptassignments

* These IRQs are usually available for ISA or PCI devices.

IRQ Priority Standardfunction

0 1 System Timer

1 2 Keyboard Controller

2 - Programmable Interrupt

4* 12 Communications Port (COM1)

5* 13 --

7* 15 --

8 3 System CMOS/Real Time Clock

9* 4 ACPI Mode when used

10* 5 IRQ Holder for PCI Steering

11* 6 IRQ Holder for PCI Steering

12* 7 PS/2 Compatible Mouse Port

13 8 Numeric Data Processor

14*

15*

2-21

ASUS TS100-E10-PI4

2.8 System fan

This section describes how to remove the system fan in the event that you need to install or

remove previously installed or new system components, or when the system fan needs to be

replaced because it was damaged or became defective.

To remove the system fan:

1. Disconnect the system fan cable from

the REAR_FAN1 connector on the

motherboard.

3. Remove the system fan.

2. Remove the four system fan screws at

the rear panel. Keep the screws for later

use.

Hold the system fan with one hand

while removing the system fan screws.

Follow the previous instructions in

reverse order if you want to reinstall

the system fan.

Chapter 2: Hardware Information

2-22

P11C-X/AUDIO

Intel®

C242

Super

I/O

ASPEED

AST2510

ASM

1083

DDR4 DIMM_B2 (64bit, 288-pin module)

DDR4 DIMM_B1 (64bit, 288-pin module)

DDR4 DIMM_A2 (64bit, 288-pin module)

DDR4 DIMM_A1 (64bit, 288-pin module)

EATX12V1

EATXPWR1

SMBUS1

PCH_MFG1

ME_RCVR1

SATA1

SATA3

SATA5

BUZZ1

SATA2

SATA4

SATA6

PANEL1

AUX_PANEL1

HDLED1

CLRTC1

INTRUSION1

SGPIO1

VGA_SW1

LAN_SW1

USB3_34

USB78

VGA1

COM1

CPU_FAN1

FRNT_FAN4

FRNT_FAN1

FRNT_FAN2

TPM1 USB14

FRNT_FAN3

REAR_FAN1

LAN1

LAN2_USB3_56

KB_USB1011

USB31_12

PCI5

PCI4

PCIE3

PCIE6

CPU1

NGFF2

22422260228022110

NGFF1

22422260228022110

MLED1

PLED1

LOCLED1

SBPWR1

Lithium Cell

CMOS Power

Intel

I219LM

Intel

I210 AT

DIGI+

EPU

LPT1

PWR_SW1

AUDIO

AAFP

SPDIF_OUT

U2_CFG5

U2_CFG6

2.9 Cable connections

• The bundled system cables are pre-connected before shipment. You do not need to

disconnect these cables unless you will remove pre-installed components to install

additional devices.

• Refer to Chapter 3 for detailed information on the connectors.

Standard cables connected to the motherboard

1. 24-pin ATX power connector (from power supply to motherboard)

2. 8-pin ATX 12V power connector (from power supply to motherboard)

3. System fan connector (from motherboard to system)

4. SATA connectors (system default; from motherboard to SATA devices)

5. USB connectors (from motherboard to front I/O board)

6. System panel connector (from motherboard to front I/O board)

This chapter includes the motherboard layout and brief

descriptions of the jumpers and internal connectors.

Motherboard Information

Chapter 3: Motherboard Information

3-2

3.1 Motherboard layout

ASUS TS100-E10-PI4 3-3

Layout contents

Internal connectors / Sockets / Jumpers / LEDs Page

1. ATX power connectors (24-pin EATXPWR1; 8-pin EATX12V1) 3-13

2. CPU, front, and rear fan connectors (4-pin FRNT_FAN1-4; REAR_

FAN1; CPU_FAN1) 3-12

3. DDR4 DIMM sockets 2-9

4. CPU socket 2-4

5. System Management Bus (SMBUS) connector (5-1 pin SMBUS1) 3-17

6. PCH_MFG1 setting (3-pin PCH_MFG1) 3-7

7. ME rmware force recovery setting (3-pin ME_RCVR1) 3-6

8. USB 3.0 connector (20-1 pin USB3_34) 3-11

9. CPU PCIE conguration settings (3-pin U2_CFG5-6) 3-6

10. Serial ATA 6.0Gb/s connectors (7-pin SATA1-6) 3-9

11. Auxiliary panel connector (20-2 pin AUX_PANEL1) 3-15

12. System panel connector (20-1 pin PANEL1) 3-14

13. Serial General Purpose Input/Output connector (6-1 pin SGPIO1) 3-11

14. USB 2.0 connectors (5-1 pin USB14; 10-1 USB78) 3-10

15. Hard disk activity LED connector (4-pin HDLED1) 3-10

16. Chassis intrusion connector (2-pin INTRUSION1) 3-17

17. Trusted Platform Module connector (14-1 pin TPM1) 3-9

18. Clear RTC RAM (3-pin CLRTC1) 3-4

19. LPT connector (26-1 pin LPT1) 3-18

20. Serial port connector (10-1 pin COM1) 3-12

21. Front panel audio connector (10-1 pin AAFP) 3-18

22. Digital audio connector (4-1 pin SPDIF_OUT) 3-19

23. M.2 (NGFF) connector (NGFF1-2) 3-16

24. LAN controller setting (3-pin LAN_SW1) 3-5

25. VGA controller setting (3-pin VGA_SW1) 3-5

Chapter 3: Motherboard Information

3-4

3.2 Jumpers

1. Clear RTC RAM (3-pin CLRTC1)

This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can

clear the CMOS memory of date, time, and system setup parameters by erasing the

CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS

which include system setup information such as system passwords.

To erase the RTC RAM:

1. Turn OFF the computer and unplug the power cord.

2. Move the jumper cap from the default pins 1–2 to pins 2–3. Keep the cap on pins

2–3 for about 5 to 10 seconds, then move the cap back to pins 1–2.

3. Plug the power cord and turn ON the computer.

4. Hold down the <Del> key during the boot process and enter BIOS setup to re-

enter data.

DO NOT remove the cap on CLRTC jumper default position except when clearing the RTC

RAM. Removing the cap will cause system boot failure!

If the steps above do not help, remove the onboard battery and move the jumper again to

clear the CMOS RTC RAM data. After the CMOS clearance, reinstall the battery.

ASUS TS100-E10-PI4 3-5

2. VGA controller setting (3-pin VGA_SW1)

This jumper allows you to enable or disable the onboard VGA controller. Set to pins 1–2

to activate the VGA feature.

3. LAN controller setting (3-pin LAN_SW1)

This jumper allows you to enable or disable the onboard LAN_SW1. Set to pins 1-2 to

activate the Gigabit LAN feature.

Chapter 3: Motherboard Information

3-6

4. MErmwareforcerecoverysetting(3-pinME_RCVR1)

This jumper allows you to force Intel® Management Engine (ME) boot from recovery

mode when ME becomes corrupted.

5. CPUPCIEcongurationsettings(3-pinU2_CFG5-6)

These jumpers allow you to congure the speed at which PCIE6 will run at. Refer to the

table below for the different jumper congurations.

Jumper Setting

U2_CFG6 U2_CFG5 PCIE6slotconguration

x16 (Default)

x8, x8

x8, x4, x4

ASUS TS100-E10-PI4 3-7

6. PCH_MFG1setting(3-pinPCH_MFG1)

This jumper allows you to update the BIOS ME block.

3.3 Onboard LEDs

1. StandbyPowerLED(SBPWR1)

The motherboard comes with a standby power LED. The green LED lights up to

indicate that the system is ON, in sleep mode, or in soft-off mode. This is a reminder

that you should shut down the system and unplug the power cable before removing or

plugging in any motherboard component. The illustration below shows the location of

the onboard LED.

Chapter 3: Motherboard Information

3-8

3. Location LED (LOCLED1)

This onboard LED lights up when triggered by a system management software. The

Location LED helps visually locate and quickly identify the workstation in error on a

rack.

2. Message LED (MLED1)

This onboard LED lights up when the SIO detects that the CPU temperature has

reached 95°C.

ASUS TS100-E10-PI4 3-9

3.4 Internal connectors

1. SerialATA6.0Gb/sconnectors(7-pinSATA1-6)

Supported by the Intel® C242 chipset, these connectors are for the Serial ATA signal

cables for Serial ATA hard disk drives that allows up to 6Gb/s of data transfer rate.

If you installed Serial ATA hard disk drives, you can create a RAID 0, RAID 1, RAID 10,

or RAID 5 conguration.

• The actual data transfer rate depends on the speed of Serial ATA hard disks installed.

• When the M.2 (NGFF1) is operating in SATA mode, SATA5 will be disabled.

• When the M.2 (NGFF2) is operating in SATA mode, SATA6 will be disabled.

2. TrustedPlatformModuleconnector(14-1pinTPM1)

This connector supports a TPM (Trusted Platform Module) system, which can securely

store keys, digital certicates, passwords, and data. A TPM system also helps enhance

network security, protects digital identities, and ensures platform integrity.

Chapter 3: Motherboard Information

3-10

3. HarddiskactivityLEDconnector(4-pinHDLED1)

This LED connector is for the storage add-on card cable connected to the SATA or

SAS add-on card. The read or write activities of any device connected to the SATA or

SAS add-on card causes the front panel LED to light up.

4. USB2.0connectors(5-1pinUSB14;10-1USB78)

These connectors allow you to connect a USB 2.0 module for additional USB 2.0 front

or rear panel ports. These USB connectors comply with USB 2.0 specication that

supports up to 480 Mbps connection speed.

ASUS TS100-E10-PI4 3-11

5. USB3.0connector(20-1pinUSB3_34)

This connector allows you to connect a USB 3.0 module for additional USB 3.0 front

or rear panel ports. With an installed USB 3.0 module, you can enjoy all the benets of

USB 3.0 including faster data transfer speeds of up to 5 Gbps, faster charging time for

USB-chargeable devices, optimized power efciency, and backward compatibility with

USB 2.0.

6. SerialGeneralPurposeInput/Outputconnector(6-1pinSGPIO1)

The SGPIO 1 connector is used for the Intel Rapid Storage Technology Enterprise

SGPIO interface that controls the LED pattern generation, device information, and

general purpose data.

Chapter 3: Motherboard Information

3-12

• DO NOT forget to connect the fan cables to the fan connectors. Insufcient air ow

inside the system may damage the motherboard components.

• These are not jumpers! DO NOT place jumper caps on the fan connectors!

• All fans feature the ASUS Smart Fan technology.

7. CPU,front,andrearfanconnectors

 (4-pinFRNT_FAN1-4;REAR_FAN1;CPU_FAN1)

The fan connectors support cooling fans. Connect the fan cables to the fan connectors

on the motherboard, ensuring that the black wire of each cable matches the ground pin

of the connector.

8. Serialportconnector(10-1pinCOM1)

This connector is for the serial COM port. Connect the serial port module cable to one

of these connectors, then install the module to a slot opening at the back of the system

chassis.

ASUS TS100-E10-PI4 3-13

• DO NOT forget to connect the 24-pin and the 8-pin power plugs; otherwise, the system

will not boot up.

• Use of a power supply unit (PSU) with a higher power output is recommended when

conguring a system with more power-consuming devices. The system may become

unstable or may not boot up if the power is inadequate.

• This motherboard supports ATX2.0 PSU or later version.

• Ensure that your PSU can provide at least the minimum power required by your

system.

9. ATXpowerconnectors(24-pinEATXPWR1;8-pinEATX12V1)

These connectors are for the ATX power supply plugs. The power supply plugs are

designed to t these connectors in only one orientation. Find the proper orientation and

push down rmly until the connectors completely t.

Chapter 3: Motherboard Information

3-14

10. Systempanelconnector(20-1pinPANEL1)

This connector supports several chassis-mounted functions.

1. SystempowerLED(3-pinPLED)

This 3-pin connector is for the system power LED. Connect the chassis power

LED cable to this connector. The system power LED lights up when you turn on

the system power, and blinks when the system is in sleep mode.

2. Message LED (2-pin MLED)

This 2-pin connector is for the message LED cable that connects to the front

message LED. The LED lights up when the SIO detects that the CPU temperature

has reached 95°C.

3. Systemwarningspeaker(4-pinSPEAKER)

This 4-pin connector is for the chassis-mounted system warning speaker. The

speaker allows you to hear system beeps and warnings.

4. HarddiskdriveactivityLED(2-pin+HDLED)

This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED

cable to this connector. The IDE LED lights up or ashes when data is read from

or written to the HDD.

5. Powerbutton/soft-offbutton(2-pinPWRSW)

This connector is for the system power button. Pressing the power button turns

the system on or puts the system in sleep or soft-off mode depending on the

BIOS settings. Pressing the power switch for more than four seconds while the

system is ON turns the system OFF.

6. Resetbutton(2-pinRESET)

This 2-pin connector is for the chassis-mounted reset button for system reboot

without turning off the system power.

ASUS TS100-E10-PI4 3-15

11. Auxiliarypanelconnector(20-2pinAUX_PANEL1)

This connector is for additional front panel features including front panel SMB, locator

LED and switch, chassis intrusion, and LAN LEDs.

1. FrontpanelSMB(6-1pinFPSMB)

These leads connect the front panel SMBus cable.

2. LANactivityLED(2-pinLAN1_LED,LAN2_LED)

These leads are for the Gigabit LAN activity LEDs on the front panel.

3. LocatorLED(2-pinLOCATORLED1,LOCATORLED2)

These leads are for the locator LED1 and LED2 on the front panel. Connect the

Locator LED cables to these 2-pin connector. The LEDs will light up when the

Locator button is pressed.

4. LocatorButton/Switch(2-pinLOCATORBTN)

These leads are for the locator button on the front panel. This button queries the

state of the system locator.

Chapter 3: Motherboard Information

3-16

12. M.2(NGFF)connector(NGFF1-2)

These connectors allow you to install M.2 devices.

The M.2 (NGFF) device is purchased separately.

• NGFF1 supports PCIe 3.0 x2 and SATA mode M Key design and type 2242 / 2260 /

2280 / 22110 PCIe and SATA storage devices.

• NGFF2 supports SATA mode M Key design and type 2242 / 2260 / 2280 / 22110

SATA storage devices.

• When the M.2 (NGFF1) is operating in SATA mode, SATA5 will be disabled.

• When the M.2 (NGFF2) is operating in SATA mode, SATA6 will be disabled.

ASUS TS100-E10-PI4 3-17

13. SystemManagementBus(SMBUS)connector(5-1pinSMBUS1)

This connector controls the system and power management-related tasks. This

connector processes the messages to and from devices rather than tripping the

individual control lines.

14. Chassis intrusion connector (2-pin INTRUSION1)

This connector is for a chassis-mounted intrusion detection sensor or switch. Connect

one end of the chassis intrusion sensor or switch cable to this connector. The chassis

intrusion sensor or switch sends a high-level signal to this connector when a chassis

component is removed or replaced. The signal is then generated as a chassis intrusion

event.

By default, the pin labeled “Chassis Signal” and “Ground” are shorted with a jumper

cap. Remove the jumper caps only when you intend to use the chassis intrusion

detection feature.

Chapter 3: Motherboard Information

3-18

15. LPTconnector(26-1pinLPT1)

The LPT (Line Printing Terminal) connector supports devices such as a printer. LPT

standardizes as IEEE 1284, which is the parallel port interface on IBM PC-compatible

computers.

16. Frontpanelaudioconnector(10-1pinAAFP)

This connector is for a chassis-mounted front panel audio I/O module that supports HD

Audio. Connect one end of the front panel audio I/O module cable to this connector.

We recommend that you connect a high-denition front panel audio module to this

connector to avail of the motherboard’s high-denition audio capability.

ASUS TS100-E10-PI4 3-19

17. Digitalaudioconnector(4-1pinSPDIF_OUT)

This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port. Connect

the S/PDIF Out module cable to this connector, then install the module to a slot

opening at the back of the system chassis.

The S/PDIF module is purchased separately.

Chapter 3: Motherboard Information

3-20

BIOS Setup

This chapter tells how to change the system settings through

the BIOS Setup menus. Detailed descriptions of the BIOS

parameters are also provided.

Chapter 4: BIOS Setup

4-2 Chapter 4: BIOS Setup

4.1 Managing and updating your BIOS

The following utilities allow you to manage and update the motherboard Basic Input/Output

System (BIOS) setup:

1. ASUS CrashFree BIOS 3

 TorecovertheBIOSusingabootableUSBashdiskdrivewhentheBIOSlefailsor

gets corrupted.

2. ASUS EzFlash

 UpdatestheBIOSusingaUSBashdisk.

3. BUPDATER

 UpdatestheBIOSinDOSmodeusingabootableUSBashdiskdrive.

Refer to the corresponding sections for details on these utilities.

Recovering the BIOS from a USB ash drive

TorecovertheBIOSfromaUSBashdrive:

1. InserttheUSBashdrivewiththeoriginalorupdatedBIOSletooneUSBportonthe

system.

2. The utility will automatically recover the BIOS. It resets the system when the BIOS

recoverynished.

DO NOT shut down or reset the system while recovering the BIOS! Doing so would cause

system boot failure!

The recovered BIOS may not be the latest BIOS version for this motherboard. Visit the

ASUSwebsiteatwww.asus.comtodownloadthelatestBIOSle.

SaveacopyoftheoriginalmotherboardBIOSletoabootableUSBashdiskdrivein

case you need to restore the BIOS in the future. Copy the original motherboard BIOS using

the BUPDATER utility.

4.1.1 ASUS CrashFree BIOS 3 utility

TheASUSCrashFreeBIOS3isanautorecoverytoolthatallowsyoutorestoretheBIOSle

when it fails or gets corrupted during the updating process. You can update a corrupted BIOS

leusingaUSBashdrivethatcontainstheupdatedBIOSle.

PrepareaUSBashdrivecontainingtheupdatedmotherboardBIOSbeforeusingthis

utility.

ASUS TS100-E10-PI4 4-3

3. Press <Tab> to switch to the Driveeld.

4. PresstheUp/DownarrowkeystondtheUSBashdiskthatcontainsthelatestBIOS,

then press <Enter>.

5. Press <Tab> to switch to the Folder Infoeld.

4.1.2 ASUS EZ Flash Utility

The ASUS EZ Flash Utility feature allows you to update the BIOS without having to use a

DOS-based utility.

Beforeyoustartusingthisutility,downloadthelatestBIOSfromtheASUSwebsiteat

www.asus.com.

To update the BIOS using EZ Flash Utility:

1. InserttheUSBashdiskthatcontainsthelatestBIOSleintotheUSBport.

2. Enter the BIOS setup program. Go to the Tool menu then select ASUS EZ Flash

Utility. Press <Enter>.

ASUS Tek. EzFlash Utility

[Up/Down/Left/Right]:Switch [Enter]:Choose [q]:Exit

FS0 System Volume Information <DIR>

Windows <DIR>

P11C-X/AUDIO BIOS <DIR>

Current Platform

Platform : P11C-X/AUDIO

Version : 0201

Build Date :12/04/2018

New Platform

Platform : P11C-X/AUDIO

Version : 0207

Build Date :01/05/2018

4-4 Chapter 4: BIOS Setup

6. PresstheUp/DownarrowkeystondtheBIOSle,andthenpress<Enter>toperform

the BIOS update process. Reboot the system when the update process is done.

• ThisfunctioncansupportdevicessuchasaUSBashdiskwithFAT32/16formatand

single partition only.

• DO NOT shut down or reset the system while updating the BIOS to prevent system

boot failure!

Ensure to load the BIOS default settings to ensure system compatibility and stability. Press

<F5> and select Yes to load the BIOS default settings.

4.1.3 BUPDATER utility

The succeeding BIOS screens are for reference only. The actual BIOS screen displays

may not be the same as shown.

TheBUPDATERutilityallowsyoutoupdatetheBIOSleintheDOSenvironmentusinga

bootableUSBashdiskdrivewiththeupdatedBIOSle.

Updating the BIOS le

ToupdatetheBIOSleusingtheBUPDATERutility:

1. Visit the ASUS website at www.asus.comanddownloadthelatestBIOSleforthe

motherboard.SavetheBIOSletoabootableUSBashdiskdrive.

2. Copy the BUPDATER utility (BUPDATER.exe) from the ASUS support website at

https://www.asus.com/supporttothebootableUSBashdiskdriveyoucreatedearlier.

3. BootthesysteminDOSmode,thenattheprompt,type:

BUPDATER /i[lename].CAP

where[lename]isthelatestortheoriginalBIOSleonthebootableUSBashdisk

drive,thenpress<Enter>.

A:\>BUPDATER /i[le name].CAP

ASUS TS100-E10-PI4 4-5

4. Theutilityveriesthele,thenstartsupdatingtheBIOSle.

DO NOT shut down or reset the system while updating the BIOS to prevent system boot

failure!

5. The utility returns to the DOS prompt after the BIOS update process is completed.

Rebootthesystemfromtheharddiskdrive.

The BIOS update is nished! Please restart your system.

C:\>

Current Platform

Platform : P11C-X/AUDIO

Version : 0201

Build date: 12/04/2018

New Platform

Platform : P11C-X/AUDIO

Version : 0207

Build date: 01/05/2018

ASUS Tek. EzFlash Utility

Start Programming Flash. DO NOT SHUTDOWN THE SYSTEM!!!

Write

75%

4-6 Chapter 4: BIOS Setup

4.2 BIOS setup program

Thismotherboardsupportsaprogrammablermwarechipthatyoucanupdateusingthe

provided utility described in section 4.1 Managing and updating your BIOS.

UsetheBIOSSetupprogramwhenyouareinstallingamotherboard,reconguringyour

system,orpromptedto“RunSetup.”Thissectionexplainshowtocongureyoursystem

using this utility.

EvenifyouarenotpromptedtousetheSetupprogram,youcanchangethecongurationof

yourcomputerinthefuture.Forexample,youcanenablethesecuritypasswordfeatureor

changethepowermanagementsettings.Thisrequiresyoutorecongureyoursystemusing

the BIOS Setup program so that the computer can recognize these changes and record them

intheCMOSRAMofthermwarechip.

ThermwarechiponthemotherboardstorestheSetuputility.Whenyoustartupthe

computer,thesystemprovidesyouwiththeopportunitytorunthisprogram.Press<Del>

duringthePower-OnSelf-Test(POST)toentertheSetuputility;otherwise,POSTcontinues

with its test routines.

IfyouwishtoenterSetupafterPOST,restartthesystembypressing<Ctrl+Alt+Delete>,orby

pressing the reset button on the system chassis. You can also restart by turning the system

offandthenbackon.Dothislastoptiononlyifthersttwofailed.

TheSetupprogramisdesignedtomakeitaseasytouseaspossible.Beingamenu-driven

program,itletsyouscrollthroughthevarioussub-menusandmakeyourselectionsfromthe

availableoptionsusingthenavigationkeys.

• The default BIOS settings for this motherboard apply for most conditions to ensure

optimum performance. If the system becomes unstable after changing any BIOS

settings,loadthedefaultsettingstoensuresystemcompatibilityandstability.Press

<F5> and select Yes to load the BIOS default settings.

• TheBIOSsetupscreensshowninthissectionareforreferencepurposesonly,and

may not exactly match what you see on your screen.

• VisittheASUSwebsite(www.asus.com)todownloadthelatestBIOSleforthis

motherboard.

ASUS TS100-E10-PI4 4-7

4.2.1 BIOS menu screen

Navigation keys

General helpMenu bar Conguration eldsMenu items

4.2.2 Menu bar

The menu bar on top of the screen has the following main items:

Main   Forchangingthebasicsystemconguration

Advanced For changing the advanced system settings

Chipset For changing the chipset settings

Security For changing the security settings

Boot   Forchangingthesystembootconguration

Monitor  Fordisplayingthesystemtemperature,powerstatus,andchanging

the fan settings

Tool   Forconguringoptionsforspecialfunctions

Event Logs For changing the event log settings

Save & Exit For selecting the save & exit options

Toselectanitemonthemenubar,presstherightorleftarrowkeyonthekeyboarduntilthe

desired item is highlighted.

4-8 Chapter 4: BIOS Setup

4.2.3 Menu items

Thehighlighteditemonthemenubardisplaysthespecicitemsforthatmenu.Forexample,

selecting Main shows the Main menu items.

Theotheritems(Advanced,Chipset,Security,Boot,Monitor,Tool,EventLogs,andSave&

Exit) on the menu bar have their respective menu items.

4.2.4 Submenu items

A solid triangle before each item on any menu screen means that the item has a submenu.

Todisplaythesubmenu,selecttheitemthenpress<Enter>.

4.2.5 Navigation keys

AtthebottomrightcornerofamenuscreenarethenavigationkeysfortheBIOSsetup

program.Usethenavigationkeystoselectitemsinthemenuandchangethesettings.

4.2.6 General help

At the top right corner of the menu screen is a brief description of the selected item.

4.2.7 Conguration elds

Theseeldsshowthevaluesforthemenuitems.Ifanitemisuser-congurable,youcan

changethevalueoftheeldoppositetheitem.Youcannotselectanitemthatisnotuser-

congurable.

Acongurableeldisenclosedinbrackets,andishighlightedwhenselected.Tochangethe

valueofaeld,selectitandpress<Enter>todisplayalistofoptions.

4.2.8 Pop-up window

Selectamenuitemandpress<Enter>todisplayapop-upwindowwiththeconguration

options for that item.

4.2.9 Scroll bar

Ascrollbarappearsontherightsideofamenuscreenwhenthereareitemsthatdonotton

thescreen.PresstheUp/Downarrowkeysor<PageUp>/<PageDown>keystodisplaythe

other items on the screen.

ASUS TS100-E10-PI4 4-9

4.3 Main menu

WhenyouentertheBIOSSetupprogram,theMainmenuscreenappears.TheMainmenu

providesyouanoverviewofthebasicsysteminformation,andallowsyoutosetthesystem

date,time,andlanguage.

System Date [Day MM/DD/YYYY]

Allows you to set the system date.

System Time [HH:MM:SS]

Allows you to set the system time.

4-10 Chapter 4: BIOS Setup

4.4 Advanced menu

The Advanced menu items allow you to change the settings for the CPU and other system

devices.

TakecautionwhenchangingthesettingsoftheAdvancedmenuitems.Incorrecteld

values can cause the system to malfunction.

ASUS TS100-E10-PI4 4-11

4.4.1 CPU Conguration

C6DRAM [Enabled]

Allows you to enable or disable moving of DRAM contents to PRM memory when the CPU is

in C6 state.

Congurationoptions:[Disabled][Enabled]

Software Guard Extensions (SGX) [Software Controlled]

Allows you to select the behavior of Software Guard Extensions (SGX).

Congurationoptions:[SoftwareControlled][Disabled][Enabled]

The following item appears only when you set Software Guard Extensions (SGX) to

[Enabled] or [Software Controlled].

Select Owner EPOCH input type [No change in Owner EPOCHs]

Allows you to select the behavior of EPOCH input type.

Congurationoptions:[NochangeinOwnerEPOCHs][ChangetoNewRandom

EPOCHs][ManualUserDenedOwnerEPOCHs]

SGX Launch Control Policy [Unlocked]s]

AllowsyoutoselectthebehaviorofSGXLaunchControlPolicy.

Congurationoptions:[IntelLocked][Unlocked][Locked]

4-12 Chapter 4: BIOS Setup

CPU Flex Ratio Override [Disabled]

Allows you to enable or disable CPU Flex Ratio Override.

Congurationoptions:[Disabled][Enabled]

The following item appears only when you set CPU Flex Ratio Override to [Enabled].

CPU Flex Ratio Settings [37]

Allows you to set the CPU Flex Ratio.

ThisvaluemustbebetweentheMaxEfciencyRatio(LFM)andtheMaximum

non-turboratiosetbytheHardware(HFW).

Hardware Prefetcher [Enabled]

ThisItemallowsyoutoturnon/offtheMLCstreamerprefetcher.

Congurationoptions:[Disabled][Enabled]

Adjacent Cache Prefetch [Enabled]

This Item allows you to turn on/off prefetching of adjacent cache lines.

Congurationoptions:[Disabled][Enabled]

Intel (VMX) Virtualization Technology [Enabled]

Enable this item to allow a VMM to utilize the additional hardware capabilities provided by

Vanderpool Technology.

Congurationoptions:[Disabled][Enabled]

Active Processor Cores [ALL]

Thisitemallowsyoutosetthenumberofcorestoenableineachprocessorpackage.

Congurationoptions:[All][1][2][3][4][5]

Hyper-Threading [Enabled]

EnablethisoptionofWindowsXPandLinux(OSoptimizedforHyper-ThreadingTechnology).

Disable this item for other OS (OS not optimized for Hyper-Threading Technology).

Congurationoptions:[Disabled][Enabled]

BIST [Disabled]

Allows you to enable or disable BIST (Built-In Self Test) on reset.

Congurationoptions:[Disabled][Enabled]

AES [Enabled]

Allows you to enable or disable AES (Advanced Encryption Standard).

Congurationoptions:[Disabled][Enabled]

Intel Trusted Execution Technology [Disabled]

Allows you to enable or disable utilization of additional hardware capabilities provided by

Intel(R)TrustedExecutionTechnology.Changesrequireafullpowercycletotakeeffect.

Congurationoptions:[Disabled][Enabled]

ASUS TS100-E10-PI4 4-13

4.4.2 Power & Performance

CPU - Power Management Control

Boot performance mode [Max Non-Turbo Performance]

This item allows you to select the performance state that the BIOS will set starting from reset

vector.

Congurationoptions:[MaxBattery][MaxNon-TurboPerformance][TurboPerformance]

Intel(R) SpeedStep(tm) [Enabled]

Allows more than two frequency ranges to be supported.

Congurationoptions:[Disabled][Enabled]

Race To Halt (RTH) [Enabled]

Allows you to enable or disable Race To Halt feature. RTH will dynamically increase CPU

frequencyinordertoenterpkgC-Statefastertoreduceoverallpower.RTHiscontrolled

through MSR 1FC bit 20.

Congurationoptions:[Disabled][Enabled]

Intel(R) Speed Shift Technology [Disabled]

Allows you to enable or disable Intel(R) Speed Shift Technology support. Enabling will expose

the CPPC v2 interface to allow for hardware controlled P-states.

Congurationoptions:[Disabled][Enabled]

HDC Control [Enabled]

[Disabled] DisableHDC.

[Enabled] CanbeenablebyOSifOSnativesupportavailable.

Turbo Mode [Enabled]

Allows you to enable or disable processor turbo mode if EMTTM is also enabled.

Congurationoptions:[Disabled][Enabled]

C-States [Enabled]

AllowsyoutoenableordisableCPUpowermanagement,thisallowstheCPUtoenterC-state

when not it is not 100 % utilized.

Congurationoptions:[Disabled][Enabled]

The following items appears only when you set C-States to [Enabled].

Enhanced C-States [Enabled]

Allows you to enable or disable C11E. Enable this item to allow the CPU to switch to

minimum speed when all cores enter C-State.

Congurationoptions:[Disabled][Enabled]

4-14 Chapter 4: BIOS Setup

C-State Auto Demotion [C1 and C3]

ThisitemallowsyoutoconguretheC-stateautodemotion.

Congurationoptions:[Disabled][C1][C3][C1andC3]

C-State Un-demotion [C1 and C3]

ThisitemallowsyoutoconguretheC-stateUn-demotion.

Congurationoptions:[Disabled][C1][C3][C1andC3]

Package C-State Demotion [C1 and C3]

ThisitemallowsyoutocongurethePackageC-StateDemotion.

Congurationoptions:[Disabled][C1][C3][C1andC3]

Package C-State Un-demotion [C1 and C3]

ThisitemallowsyoutocongurethePackageC-stateUn-demotion.

Congurationoptions:[Disabled][C1][C3][C1andC3]

Package C-state Limit [Auto]

ThisitemallowsyoutoselectthemaximumpackageC-statelimitsetting.

Congurationoptions:[C0/C1][C2][C3][C6][C7][C7S][C8][C9][C10][CPUDefault]

[Auto]

Thermal Monitor [Enabled]

Allows you to enable or disable Thermal Monitoring.

Congurationoptions:[Disabled][Enabled]

TPM Device Selection [PTT]

Allows you to select the TPM device.

Congurationoptions:[PTT][dTPM]

4.4.3 Server ME Conguration

ASUS TS100-E10-PI4 4-15

Security Device Support [Enabled]

This item allows you to enable or disable Security Device Support.

Congurationoptions:[Disabled][Enabled]

4.4.4 Trusted Computing

4.4.5 APM Conguration

Restore AC Power Loss [Last State]

Whensetto[PowerOff],thesystemgoesintooffstateafteranACpowerloss.Whenset

to[PowerOn],thesystemwillrebootafteranACpowerloss.Whensetto[LastState],the

systemgoesintoeitherofforonstate,whateverthesystemstatewasbeforetheACpower

loss.

Congurationoptions:[PowerOff][PowerOn][LastState]

Power On By PCI-E/PCI [Disabled]

[Disabled] DisablesthePCIorPCIEdevicestogenerateawakeevent.

[Enabled] EnablesthePCIorPCIEdevicestogenerateawakeevent.

Power On By RTC [Disabled]

[Disabled] DisablesRTCtogenerateawakeevent.

[Enabled] Whensetto[Enabled],theitemsRTC Alarm Date (Days) and

Hour/Minute/Secondwillbecomeuser-congurablewithsetvalues.

4-16 Chapter 4: BIOS Setup

Onboard I210 LAN Conguration

Intel I210 LAN1

LAN Enable [Enabled]

AllowsyoutoenableordisabletheIntelLAN.

Congurationoptions:[Disabled][Enabled]

The following item appears only when you set LAN Enable to [Enabled].

Intel LAN ROM Type [PXE]

AllowsyoutoselecttheIntelLANROMtype.

Congurationoptions:[Disabled][PXE][iSCSI]

Due to Intel®limitations,bothIntelLANROMTypeoptionsshouldbethesamewhen[PXE]

or [iSCSI] is selected.

4.4.7 Onboard LAN Conguration

Runtime Error Logging System Enabling [Enabled]

ThisitemallowsyoutoenableordisableRuntimeErrorLoggingSystem.

Congurationoptions:[Disabled][Enabled]

4.4.6 Runtime Error Logging Settings

ASUS TS100-E10-PI4 4-17

4.4.8 Serial Port Console Redirection

Console Redirection Settings

TheseitemsbecomecongurableonlywhenyouenabletheConsole Redirection

item. The settings specify how the host computer and the remote computer (which the

user is using) will exchange data. Both computers should have the same or compatible

settings.

Terminal Type [VT-UTF8]

Allows you to set the terminal type.

[VT100] ASCIIcharset.

[VT100+] ExtendsVT100tosupportcolor,functionkeys,etc.

[VT-UTF8] UsesUTF8encodingtomapUnicodecharsonto1ormorebytes.

[ANSI] ExtendedASCIIcharset.

Bits per second [57600]

Selects serial port transmission speed. The speed must be matched on the other side.

Longornoisylinesmayrequirelowerspeeds.

Congurationoptions:[9600][19200][38400][57600][115200]

Data Bits [8]

Congurationoptions:[7][8]

The following item appears only when you set Console Redirection to [Enabled].

COM1

Console Redirection [Disabled]

Allows you to enable or disable the console redirection feature.

Congurationoptions:[Disabled][Enabled]

4-18 Chapter 4: BIOS Setup

Parity [None]

Aparitybitcanbesentwiththedatabitstodetectsometransmissionerrors.[Mark]

and[Space]paritydonotallowforerrordetection.

[None] None

[Even] paritybitis0ifthenumof1’sinthedatabitsiseven

[Odd] paritybitis0ifnumof1’sinthedatabitsisodd

[Mark] paritybitisalways1

[Space] paritybitisalways0

Stop Bits [1]

Stopbitsindicatetheendofaserialdatapacket.(Astartbitindicatesthebeginning.)

The standard setting is 1 stop bit. Communication with slow devices may require more

than 1 stop bit.

Congurationoptions:[1][2]

Flow Control [Hardware RTS/CTS]

Flowcontrolcanpreventdatalossfrombufferoverow.Whensendingdata,ifthe

receivingbuffersarefull,a“stop”signalcanbesenttostopthedataow.Oncethe

buffersareempty,a“start”signalcanbesenttore-starttheow.Hardwareowcontrol

uses two wires to send start/stop signals.

Congurationoptions:[None][HardwareRTS/CTS]

VT -UTF8 Combo Key Support [Enabled]

This allows you to enable the VT -UTF8 Combination Key Support for ANSI/VT100

terminals.

Congurationoptions:[Disabled][Enabled]

Recorder Mode [Disabled]

Withthismodeenabledonlytextwillbesent.ThisistocaptureTerminaldata.

Congurationoptions:[Disabled][Enabled]

Legacy OS Redirection Resolution [80x24]

ThisallowsyoutosetthenumberofrowsandcolumnssupportedontheLegacyOS.

Congurationoptions:[80x24][80x25]

Putty Keypad [VT100]

This allows you to select the FunctionKey and Keypad on Putty.

Congurationoptions:[VT100][LINUX][XTERMR6][SCO][ESCN][VT400]

Legacy Console Redirection Settings

Legacy Console Redirection Port [COM1]

AllowsyoutoselectaCOMporttodisplayredirectionofLegacyOSandLegacy

OPROM Messages.

Congurationoptions:[COM1]

Resolution [80x24]

Allows you to select a the number of rows and columns in supported redirection.

Congurationoptions:[80x24][80x25]

Redirect After POST [Always Enable]

Allows you to select the redirection after POST.

Congurationoptions:[AlwaysEnable][BootLoader]

ASUS TS100-E10-PI4 4-19

Serial Port for Out-of-Band Management/Windows Emergency Management

Services (EMS)

Console Redirection [Disabled]

Allows you to enable or disable the console redirection feature.

Congurationoptions:[Disabled][Enabled]

The following item appears only when you set Console Redirection to [Enabled].

Console Redirection Settings

Out-of-Band Mgmt Port [COM1]

MicrosoftWindowsEmergencyManagementServices(EMS)allowforremote

managementofaWindowsServerOSthroughaserialport.

Congurationoptions:[COM1]

Terminal Type [VT-UTF8]

MicrosoftWindowsEmergencyManagementServices(EMS)allowforremote

managementofaWindowsServerOSthroughaserialport.

Congurationoptions:[VT100][VT100+][VT-UTF8][ANSI]

Bits per second [115200]

MicrosoftWindowsEmergencyManagementServices(EMS)allowforremote

managementofaWindowsServerOSthroughaserialport.

Congurationoptions:[9600][19200][57600][115200]

Flow Control [None]

MicrosoftWindowsEmergencyManagementServices(EMS)allowforremote

managementofaWindowsServerOSthroughaserialport.

Congurationoptions:[None][HardwareRTS/CTS][SoftwareXon/Xoff]

4.4.9 Intel TXT Information

You may view the Intel TXT information in this menu.

4-20 Chapter 4: BIOS Setup

Above 4G Decoding [Disabled]

Allows you to enable or disable 64-bit capable devices to be decoded in above 4G address

space.Itonlyworksifthesystemsupports64-bitPCIdecoding.

Congurationoptions:[Disabled][Enabled]

4.4.10 PCI Subsystem Settings

AllowsyoutocongurePCI,PCI-X,andPCIExpressSettings.

4.4.11 USB Conguration

ASUS TS100-E10-PI4 4-21

Legacy USB Support [Enabled]

[Disabled] TheUSBdevicescanbeusedonlyfortheBIOSsetupprogram.Itcannot

be recognized in boot devices list.

[Enabled] EnablesthesupportforUSBdevicesonlegacyoperatingsystems(OS).

[Auto] AllowsthesystemtodetectthepresenceofUSBdevicesatstartup.If

detected,theUSBcontrollerlegacymodeisenabled.IfnoUSBdeviceis

detected,thelegacyUSBsupportisdisabled.

XHCI Hand-off [Enabled]

AllowsyoutoenableordisableworkaroundforOS(s)withoutXHCIhand-offsupport.

Congurationoptions:[Disabled][Enabled]

USB Mass Storage Driver Support [Enabled]

Allows you to enable or disable USB Mass Storage driver support.

Congurationoptions:[Disabled][Enabled]

Port 60/64 Emulation [Enabled]

Allows you to enable or disable Port 60/64 Emulation.

Congurationoptions:[Disabled][Enabled]

USB transfer time-out [20 sec]

Allows you to set the USB transfer time-out value.

Congurationoptions:[1sec][5sec][1sec][20sec]

Device reset time-out [20 sec]

Allows you to set the device reset time-out value.

Congurationoptions:[10sec]20sec][30sec][40sec]

Device power-up delay [Auto]

Allowsyoutosetthemaximumtimethedevicetakesbeforethedevicereportsitselftothe

host controller properly.

Congurationoptions:[Auto][Manual]

The following item appears only when you set Console Redirection to [Manual].

Device power-up delay in seconds [5]

Allows you to set the device power-up delay in seconds. Usethe<+>or<->toadjust

the value. The values range from 1 to 40.

Mass Storage Devices

Allows you to select the mass storage device emulation type for devices connected.

Congurationoptions:[Auto][Floppy][ForcedFDD][HardDisk][CD-ROM]

4-22 Chapter 4: BIOS Setup

4.4.12 Network Stack Conguration

Allowsyoutocongurethenetworkstackconguration.

Network Stack [Disabled]

AllowsyoutoenableordisableUEFINetworkStack.

Congurationoptions:[Disabled][Enabled]

The following items appear only when you set the Network Stack to [Enabled].

Ipv4 PXE Support [Disabled]

EnablesordisablestheIpv4PXEBootSupport.Ifdisabled,Ipv4PXEbootoptionwill

not be created.

Congurationoptions:[Disabled][Enabled]

Ipv4 HTTP Support [Disabled]

EnablesordisablestheIpv4HTTPBootSupport.Ifdisabled,Ipv4PXEbootoptionwill

not be created.

Congurationoptions:[Disabled][Enabled]

Ipv6 PXE Support [Disabled]

EnablesordisablestheIpv6PXEBootSupport.Ifdisabled,Ipv6PXEbootoptionwill

not be created.

Congurationoptions:[Disabled][Enabled]

Ipv6 HTTP Support [Disabled]

EnablesordisablestheIpv6HTTPBootSupport.Ifdisabled,Ipv6PXEbootoptionwill

not be created.

Congurationoptions:[Disabled][Enabled]

IPSEC Certificate [Enabled]

EnablesordisablessupportforIPSECCerticate.

Congurationoptions:[Disabled][Enabled]

PXE boot wait time [0]

SetthewaittimetopressESCkeytoabortthePXEboot.Usethe<+>or<->toadjust

the value. The values range from 0 to 5.

Media detect count [1]

Setthenumberoftimespresenceofmediawillbechecked.Usethe<+>or<->to

adjust the value. The values range from 1 to 50.

ASUS TS100-E10-PI4 4-23

4.4.13 CSM Conguration

CSM Support [Enabled]

This option allows you to enable or disable CSM Support.

Congurationoptions:[Disabled][Enabled]

The following items appear only when you set the CSM Support to [Enabled].

GateA20 Active [Upon Request]

This allows you to set the GA20 option.

[UponRequest] GA20canbedisabledusingBIOSservices.

[Always] DonotallowdisablingGA20;thisoptionisusefulwhenanyRT

code is executed above 1MB.

Option ROM Messages [Force BIOS]

This allows you to set the display mode for option ROM.

Congurationoptions:[ForceBIOS][KeepCurrent]

INT19 Trap Response [Immediate]

This option allows you to control the BIOS reaction on INT19 trapping by Option ROM.

[Immediate] Executethetraprightaway.

[Postponed] Executethetrapduringlegacyboot.

[Auto] Allowthesystemtodetermineautomatically.

HDD Connection Order [Adjust]

This option allows you to select the HDD Connection Order. Some OS require HDD

handles to be adjusted.

Congurationoptions:[Adjust][Keep]

Boot Option filter [Legacy only]

ThisoptionallowsyoutocontroltheLegacy/UEFIROMspriority.

Congurationoptions:[UEFIandLegacy][Legacyonly][UEFIonly]

4-24 Chapter 4: BIOS Setup

4.4.14 NVMe Conguration

You may view the NVMe controller and Drive information if an NVMe device is connected.

4.4.15 WHEA Conguration

Network / Storage / Video [Legacy]

ThisoptionallowsyoutocontroltheexecutionofUEFIandLegacyPXE/Storage/

Video OpROM.

Congurationoptions:[UEFI][Legacy]

Other PCI devices [Legacy]

ThisitemdeterminestheOpROMexecutionpolicyfordevicesotherthanNetwork,

Storage,orVideo.

Congurationoptions:[UEFI][Legacy]

Whea Support [Enabled]

ThisitemallowsyoutoenableordisabletheWHEAsupport.

Congurationoptions:[Disabled][Enabled]

ASUS TS100-E10-PI4 4-25

4.4.16 iSCSI Conguration

AllowsyoutoconguretheiSCSiparameters.

4.4.17 Tls Auth Conguration

AllowsyoutoconguretheTlsAuth.

4-26 Chapter 4: BIOS Setup

4.5.1 System Agent (SA) Conguration

4.5 Chipset menu

The Chipset menu allow you to change the platform settings.

TakecautionwhenchangingthesettingsoftheChipsetmenuitems.Incorrecteldvalues

can cause the system to malfunction.

Memory Conguration

Maximum Memory Frequency [Auto]

Allows you to select the maximum memory frequency setting.

Congurationoptions:[Auto][2133][2400][2667]

ECC Support [Enabled]

Allows you to enable or disable the ECC support.

Congurationoptions:[Disabled][Enabled]

Memory Scrambler [Enabled]

Allows you to enable or disable Memory Scrambler.

Congurationoptions:[Disabled][Enabled]

Fast Boot [Enabled]

Allows you to enable or disable Fast Boot.

Congurationoptions:[Disabled][Enabled]

ASUS TS100-E10-PI4 4-27

PEG Port Conguration

PEG 0:1:0

Max Link Speed [Auto]

AllowsyoutosettheMaxLinkSpeed.

Congurationoptions:[Auto][Gen1][Gen2][Gen3]

PEG0 Slot Power Limit Value [75]

Settheupperlimitonpowersuppliedbyslot.Usethe<+>or<->toadjustthevalue.

The values range from 0 to 255.

PEG0 Slot Power Limit Scale [1.0x]

AllowsyoutoselectthescalefortheSlotPowerLimitValue.

Congurationoptions:[1.0x][0.1x][0.01x][0.001x]

PEG0 Physical Slot Number [1]

Allows you to set the physical slot number attached to this Port. The number has to be

globally unique within the chassis. Usethe<+>or<->toadjustthevalue.Thevalues

range from 0 to 8191.

PEG 0:1:1

Max Link Speed [Auto]

AllowsyoutosettheMaxLinkSpeed.

Congurationoptions:[Auto][Gen1][Gen2][Gen3]

PEG1 Slot Power Limit Value [75]

Settheupperlimitonpowersuppliedbyslot.Usethe<+>or<->toadjustthevalue.

The values range from 0 to 255.

PEG1 Slot Power Limit Scale [1.0x]

AllowsyoutoselectthescalefortheSlotPowerLimitValue.

Congurationoptions:[1.0x][0.1x][0.01x][0.001x]

PEG1 Physical Slot Number [2]

Allows you to set the physical slot number attached to this Port. The number has to be

globally unique within the chassis. Usethe<+>or<->toadjustthevalue.Thevalues

range from 0 to 8191.

PEG 0:1:2

Max Link Speed [Auto]

AllowsyoutosettheMaxLinkSpeed.

Congurationoptions:[Auto][Gen1][Gen2][Gen3]

PEG2 Slot Power Limit Value [75]

Settheupperlimitonpowersuppliedbyslot.Usethe<+>or<->toadjustthevalue.

The values range from 0 to 255.

4-28 Chapter 4: BIOS Setup

PEG2 Slot Power Limit Scale [1.0x]

AllowsyoutoselectthescalefortheSlotPowerLimitValue.

Congurationoptions:[1.0x][0.1x][0.01x][0.001x]

PEG2 Physical Slot Number [3]

Allows you to set the physical slot number attached to this Port. The number has to be

globally unique within the chassis. Usethe<+>or<->toadjustthevalue.Thevalues

range from 0 to 8191.

PEG 0:1:3

PEG3 Slot Power Limit Value [75]

Settheupperlimitonpowersuppliedbyslot.Usethe<+>or<->toadjustthevalue.

The values range from 0 to 255.

PEG3 Slot Power Limit Scale [1.0x]

AllowsyoutoselectthescalefortheSlotPowerLimitValue.

Congurationoptions:[1.0x][0.1x][0.01x][0.001x]

PEG3 Physical Slot Number [3]

Allows you to set the physical slot number attached to this Port. The number has to be

globally unique within the chassis. Usethe<+>or<->toadjustthevalue.Thevalues

range from 0 to 8191.

VT-d [Enabled]

Allows you to enable or disable VT-d capability.

Congurationoptions:[Disabled][Enabled]

CRID Support [Disabled]

Allows you to enable or disable CRID control for Intel SIPP.

Congurationoptions:[Disabled][Enabled]

Above 4GB MMIO BIOS Assignment [Disabled]

Allows you to enable or disable above 4 GB memory mapped IO BIOS assignment. This is

enabled automatically if the aperture size is set to 2048MB.

Congurationoptions:[Disabled][Enabled]

The following item appears only when you set the VT-d to [Enabled].

X2APIC Opt Out [Disabled]

Allows you to enable or disable X2APIC Opt Out.

Congurationoptions:[Disabled][Enabled]

ASUS TS100-E10-PI4 4-29

4.5.2 PCH-IO Conguration

PCI Express Conguration

PCI Express Clock Gating [Enabled]

AllowsyoutoenableordisablePCIExpressclockgatingforeachrootport.

Congurationoptions:[Disabled][Enabled]

DMI Link ASPM Control [Enabled]

AllowsyoutoenableordisablecontrolofactivestatepowermanagementofDMIlink.

Congurationoptions:[Disabled][Enabled]

Port8xh Decode [Disabled]

Allows you to enable or PCI express port 8xh decode.

Congurationoptions:[Disabled][Enabled]

SATA And RSTe Conguration

SATA Controller(s) [Enabled]

Allows you to enable or disable the SATA Controller.

Congurationoptions:[Disabled][Enabled]

The following item appears only when you set the SATA Controller(s) to [Enabled].

SATA Mode Selection [AHCI]

Allows you to select the SATA controllers operation.

Congurationoptions:[AHCI][RAID]

Serial ATA Port 0-7

Port 0-7 [Enabled]

Allows you to enable or disable the SATA port.

Congurationoptions:[Disabled][Enabled]

Hot Plug [Enabled]

Allows you to enable or disable this port as hot pluggable.

Congurationoptions:[Disabled][Enabled]

Spin Up Device [Disabled]

Allows you to enable or disable Spin Up Device.

Congurationoptions:[Disabled][Enabled]

SATA Device Type [Hard Disk Drive]

Allows you to identify the SATA port is connected to a solid state drive or a

harddiskdrive

Congurationoptions:[HardDiskDrive][SolidStateDrive]

4-30 Chapter 4: BIOS Setup

HD Audio Conguration

HD Audio [Enabled]

Allows you to enable or disable the HD Audio.

Congurationoptions:[Disabled][Enabled]

Audio DSP [Disabled]

Allows you to enable or disable the Audio DSP.

Congurationoptions:[Disabled][Enabled]

Audio Link Mode [HD Audio Link]

Allowsyoutoselecttheaudiolinkmode.

Congurationoptions:[HDAudioLink][SSP(I2S)][Soundwire][AdvancedLinkCong]

HDA-Link Codec Select [Platform Onboard]

AllowsyoutoselecttheHDA-LinkCodec.

Congurationoptions:[PlatformOnboard][ExternalKit]

HD Audio Advanced Configuration

iDisplay Audio Disconnect [Disabled]

Allows you to enable or disable iDisplay Audio Disconnect.

Congurationoptions:[Disabled][Enabled]

Codec Sx Wake Capability [Disabled]

AllowsyoutoenableordisableCodecSxWakeCapability.

Congurationoptions:[Disabled][Enabled]

PME Enable [Disabled]

AllowsyoutoenableordisablePMEwakeofHDAudiocontrollerduring

POST.

Congurationoptions:[Disabled][Enabled]

The following item appears only when you set the Audio Link Mode to [Soundwire].

Soundwire Buffer RCOMP Setting [Non-ACT Topology]

This item allows you to select the Soundwire Buffer RCOMP Setting.

Congurationoptions:[Non-ACTTopology][ACTTopology]

HD Audio Link Frequency [24 MHz]

AllowsyoutoselecttheHDAudioLinkFrequency.

Congurationoptions:[6MHz][12MHz][24MHz]

iDisplay Audio Link Frequency [96 MHz]

AllowsyoutoselecttheiDisplayAudioLinkFrequency.

Congurationoptions:[48MHz][96MHz]

iDisplay Audio Link T-Mode [2T Mode]

AllowsyoutoselecttheiDisplayAudioLinkT-Mode.

Congurationoptions:[1TMode][2TMode]

ASUS TS100-E10-PI4 4-31

PCH LAN Controller [Enabled]

This option allows you to enable or disable onboard NIC.

Congurationoptions:[Disabled][Enabled]

The following items appear only when you set the PCH LAN Controller to [Enabled].

LAN Wake From DeepSx [Enabled]

ThisoptionallowsyoutoenableordisablewakefromDeepSxbytheassertionof

LAN_WAKE#pin.

Congurationoptions:[Disabled][Enabled]

Wake on LAN Enable [Enabled]

ThisoptionallowsyoutoenableordisableintegratedLANtowakethesystem.

Congurationoptions:[Disabled][Enabled]

SLP_LAN# Low on DC Power[Enabled]

ThisoptionallowsyoutoenableordisableSLP_LAN#LowonDCPower.

Congurationoptions:[Disabled][Enabled]

4-32 Chapter 4: BIOS Setup

4.6 Security menu

This menu allows a new password to be created or a current password to be changed. The

menualsoenablesordisablestheSecureBootstateandletstheuserconguretheSystem

Mode state.

Administrator Password

To set an administrator password:

1. Select the Administrator Password item and press <Enter>.

2.FromtheCreateNewPasswordbox,keyinapassword,thenpress<Enter>.

3.Conrmthepasswordwhenprompted.

To change an administrator password:

1. Select the Administrator Password item and press <Enter>.

2.FromtheEnterCurrentPasswordbox,keyinthecurrentpassword,thenpress<Enter>.

3.FromtheCreateNewPasswordbox,keyinanewpassword,thenpress<Enter>.

4.Conrmthepasswordwhenprompted.

Tocleartheadministratorpassword,followthesamestepsasinchanginganadministrator

password,butpress<Enter>whenpromptedtocreate/conrmthepassword.

ASUS TS100-E10-PI4 4-33

User Password

To set a user password:

1. Select the User Password item and press <Enter>.

2.FromtheCreateNewPasswordbox,keyinapassword,thenpress<Enter>.

3.Conrmthepasswordwhenprompted.

To change a user password:

1. Select the User Password item and press <Enter>.

2.FromtheEnterCurrentPasswordbox,keyinthecurrentpassword,thenpress<Enter>.

3.FromtheCreateNewPasswordbox,keyinanewpassword,thenpress<Enter>.

4.Conrmthepasswordwhenprompted.

To clear a user password:

1. Select the Clear User Password item and press <Enter>.

2.SelectYesfromtheWarningmessagewindowthenpress<Enter>.

Secure Boot

This item allows you to customize the Secure Boot settings.

Secure Boot [Disabled]

Secure Boot can be enabled if the system is running in User mode with enrolled platform Key

(EPK) or if the CSM function is disabled.

Congurationoptions:[Disabled][Enabled]

Secure Boot Mode [Custom]

Allows you to set the Secure Boot selector.

Congurationoptions:[Custom][Standard]

4-34 Chapter 4: BIOS Setup

Key Management

ThisitemonlyappearswhentheitemSecureBootModeissetto[Custom].TheKey

Management item allows you to modify Secure Boot variables and set Key Management

page.

Factory Key Provision [Disabled]

AllowsyoutoprovisionfactorydefaultSecureBootkeyswhenthesystemisinSetup

Mode.

Congurationoptions:[Disabled][Enabled]

Restore Factory keys

ThisitemwillinstallallFactoryDefaultkeys.

Reset to Setup Mode

ThisitemappearsonlywhenyouloadthedefaultSecureBootkeys.Thisitemallows

youtoclearalldefaultSecureBootkeys.

Export Secure Boot Variables

Thisitemwillaskyouifyouwanttosaveallsecurebootvariables.SelectYesifyou

wanttosaveallsecurebootvariables,otherwiseselectNo.

Enroll Efi Image

This item will allow the image to run in Secure Boot mode.

Congurationoptions:[SetNew][Append]

ASUS TS100-E10-PI4 4-35

Device Guard Ready

Remove ‘UEFI CA’ from DB

Remove Microsoft UEFI CA from Secure Boot DB.

Restore DB defaults

Restore DB variable to factory defaults.

Platform Key (PK) / Key Exchange Keys (KEK) / Authorized Signatures (DB)

/ Forbidden Signatures (DBX) / Authorized TimeStamps (DBT) / OsRecovery

Signatures

Congurationoptions:[Erase][SetNew][SavetoFile]

4.7 Boot menu

The Boot menu items allow you to change the system boot options.

4-36 Chapter 4: BIOS Setup

Setup Prompt Timeout [1]

Allowsyoutosetthenumberofsecondsthatthermwarewaitsbeforeinitiatingtheoriginal

defaultbootselection.65535(OxFFFF)meansindenitewaiting.Usethe<+>or<->toadjust

the value.

Bootup NumLock State [On]

Allowsyoutoselectthepower-onstatefortheNumLock.

Congurationoptions:[Off][On]

Quiet Boot [Disabled]

Allows you to enable or disable Quiet Boot option.

Congurationoptions:[Disabled][Enabled]

Boot Option Priorities

These items specify the boot device priority sequence from the available devices. The

number of device items that appears on the screen depends on the number of devices

installed in the system.

• Toselectthebootdeviceduringsystemstartup,press<F8>whenASUSLogo

appears.

• ToaccessWindowsOSinSafeMode,pleasepress<F8>afterPOST.

Fast Boot [Disabled]

Allows you to enable or disable boot with initialization of a minimal set of devices required to

launch active boot option. This has no effect for BBS boot options.

Congurationoptions:[Disabled][Enabled]

The following item appears only when you set the Quiet Boot to [Disabled].

POST Report [5 sec]

Allows you to set the desired POST Report waiting time from 1 to 10 seconds.

Congurationoptions:[1sec]-[10sec][UntilPressESC]

Hard Drive / CD / DVD ROM Drive BBS Priorities / Network Device BBS

Priorities

These items allow you to set the booting order of the devices.

ASUS TS100-E10-PI4 4-37

Fan Speed Control [Generic Mode]

Allowsyoutoselectthepower-onstatefortheNumLock.

Congurationoptions:[GenericMode][HighSpeedMode][FullSpeedMode][ManualSpeed

Mode]

The following item appears only when you set the Fan Speed Control to [Manual Speed

Mode].

REAR_FAN1 / CPU_FAN1 / FRNT_FAN1-3 Duty [50]

Allows you to set the desired POST Report waiting time from 1 to 10 seconds. Use the

<+>or<->toadjustthevalue.Thevaluesrangefrom10to100.

4.8 Monitor menu

Thismenudisplaysthesystemtemperature,fanspeed,andpowerstatus.Youcanalso

change the fan settings in this menu.

4-38 Chapter 4: BIOS Setup

4.10 Event Logs menu

TheEventLogsmenuitemsallowyoutochangetheeventlogsettingsandviewthesystem

event logs.

4.9 Tool menu

4.10.1 Change Smbios Event Log Settings

Press<Enter>tochangetheSmbiosEventLogconguration.

ASUS EZ Flash

Allows you to run ASUS EZ Flash BIOS ROM Utility when you press <Enter>. Refer to the

ASUS EZ Flash Utility section for details.

Enabling/Disabling Options

Smbios Event Log [Enabled]

ChangethistoenableordisableallfeaturesofSmbiosEventLoggingduringboot.

Congurationoptions:[Disabled][Enabled]

The following item appears only when you set the Smbios Event Log to [Enabled].

Erasing Settings

Erase Event Log [No]

ChooseoptionsforerasingSmbiosEventLog.Erasingisdonepriortoanyloggingactivation

during reset.

Congurationoptions:[No][Yes,Nextreset][Yes,Everyreset]

When Log is Full [Do Nothing]

ChooseoptionsforreactingtoafullSmbiosEventLog.

Congurationoptions:[DoNothing][EraseImmediately]

Smbios Event Log Standard Settings

Log System Boot Event [Enabled]

This option allows you to enable or disable logging System boot event.

Congurationoptions:[Disabled][Enabled]

Allvalueschangedheredonottakeeffectuntilcomputerisrestarted.

ASUS TS100-E10-PI4 4-39

MECI [1]

This option allows you to set the number of occurrences of a duplicate event that must pass

before the multiple-event counter of log entry is updated. Usethe<+>or<->toadjustthe

value. The values range from 1 to 255.

METW [60]

This option allows you to set the number of minutes which must pass between duplicate log

entries which utilize a multiple-event counter. Usethe<+>or<->toadjustthevalue.The

values range from 0 to 99.

Custom Options

Log EFI Status Code [Disabled]

This option allows you to enable or disable logging of the EFI Status Codes.

Congurationoptions:[Disabled][Enabled]

Convert EFI Status Codes to Standard Smbios Type [Disabled]

This option allows you to enable or disable converting of EFI Status Codes to Standard

Smbios Type (Not all may be translated).

Congurationoptions:[Disabled][Enabled]

4.10.2 View Smbios Event Log

Press <Enter> to view all smbios event logs.

4-40 Chapter 4: BIOS Setup

4.11 Save & Exit menu

The Exit menu items allow you to save or discard your changes to the BIOS items.

Pressing <Esc> does not immediately exit this menu. Select one of the options from this

menu or <F10> from the legend bar to exit.

Save Changes and Reset

Exit System setup after saving the changes.

Discard Changes and Exit

Exit System setup without saving any changes.

Restore Defaults

Restore/load default values for all the setup options.

Boot Override

These items displays the available devices. The device items that appears on the screen

dependsonthenumberofdevicesinstalledinthesystem.Clickanitemtostartbootingfrom

the selected device.

RAID Conguration

This chapter provides instructions for setting up, creating, and

conguring RAID sets using the available utilities.

Chapter 5: RAID Conguration

5-2 Chapter 5: RAID Conguration

5.1 Setting up RAID

The motherboard supports the Intel® Rapid Storage Technology enterprise Option ROM

Utility with RAID 0, RAID 1, RAID 10, and RAID 5 support.

5.1.1 RAIDdenitions

RAID 0

(Data striping)

optimizes two identical hard disk drives to read and write data in

parallel, interleaved stacks. Two hard disks perform the same work as a single drive but at a

sustained data transfer rate, double that of a single disk alone, thus improving data access

and storage. Use of two new identical hard disk drives is required for this setup.

RAID 1

(Data mirroring)

copies and maintains an identical image of data from one drive to a

second drive. If one drive fails, the disk array management software directs all applications

to the surviving drive as it contains a complete copy of the data in the other drive. This RAID

conguration provides data protection and increases fault tolerance to the entire system. Use

two new drives or use an existing drive and a new drive for this setup. The new drive must be

of the same size or larger than the existing drive.

RAID 10 is data striping and data mirroring combined without parity (redundancy data) having

to be calculated and written. With the RAID 10 conguration you get all the benets of both

RAID 0 and RAID 1 congurations. Use four new hard disk drives or use an existing drive and

three new drives for this setup.

RAID 5 stripes both data and parity information across three or more hard disk drives. Among

the advantages of RAID 5 conguration include better HDD performance, fault tolerance, and

higher storage capacity. The RAID 5 conguration is best suited for transaction processing,

relational database applications, enterprise resource planning, and other business systems.

Use a minimum of three identical hard disk drives for this setup.

If you want to boot the system from a hard disk drive included in a created RAID set, copy

rst the RAID driver from the support DVD to a oppy disk before you install an operating

system to the selected hard disk drive.

ASUS TS100-E10-PI4 5-3

5.1.3 Setting the RAID item in BIOS

You must set the RAID item in the BIOS Setup before you can create a RAID set from SATA

hard disk drives attached to the SATA connectors supported by Intel® C242 chipset.

To do this:

1. Enter the BIOS Setup during POST.

2. Go to the Chipset Menu > PCH-IOConguration > SATAAndRSTeConguration,

then press <Enter>.

3. Set SATA Mode to [RAID].

4. Press <F10> to save your changes and exit the BIOS Setup.

Refer to Chapter 4 for details on entering and navigating through the BIOS Setup.

5.1.2 Installing hard disk drives

The motherboard supports Serial ATA for RAID set conguration. For optimal performance,

install identical drives of the same model and capacity when creating a disk array.

To install the SATA hard disks for RAID conguration:

1. Install the SATA hard disks into the drive bays following the instructions in the system

user guide.

2. Connect a SATA signal cable to the signal connector at the back of each drive and to

the SATA connector on the motherboard.

3. Connect a SATA power cable to the power connector on each drive.

5-4 Chapter 5: RAID Conguration

5.2 Intel® Rapid Storage Technology enterprise SATA

Option ROM Utility

The Intel® Rapid Storage Technology enterprise SATA Option ROM utility allows you to

create RAID 0, RAID 1, RAID 10 (RAID 1+0), and RAID 5 set from Serial ATA hard disk

drives that are connected to the Serial ATA connectors supported by the Southbridge.

The navigation keys at the bottom of the screen allow you to move through the menus

and select the menu options.

The RAID BIOS setup screens shown in this section are for reference only and may not

exactly match the items on your screen.

To launch the Intel® Rapid Storage Technology enterprise SATA Option ROM utility:

1. Turn on the system.

2. During POST, press <Ctrl>+<I> to display the utility main menu.

Before you proceed, ensure that you have installed the Serial ATA hard disk drives, and

have set the correct SATA mode in the BIOS setup.

[ESC]-Exit [ENTER]-Select Menu[ ]-Select

Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023

[ MAIN MENU ]

[ DISK/VOLUME INFORMATION]

RAID Volumes:

None defined.

Physical Disks:

ID Drive Model Serial # Size Type/Status(Vol ID)

0 ST3300656SS HWAS0000991753TR 279.3GB Non-RAID Disk

1 ST3300656SS 37VN00009846RAJ1 279.3GB Non-RAID Disk

2 ST3300656SS 397600009846UEDY 279.3GB Non-RAID Disk

3 ST3300656SS GWC50000991756G6 279.3GB Non-RAID Disk

3. Reset Disks to Non-RAID

4. Exit

1. Create RAID Volume

2. Delete RAID Volume

ASUS TS100-E10-PI4 5-5

5.2.1 Creating a RAID set

To create a RAID set:

1. From the utility main menu, select 1. Create RAID Volume and press <Enter>.

2. Key in a name for the RAID set and press <Enter>.

3. Press the up/down arrow keys to select a RAID Level that you wish to create then

press <Enter>.

4. From the Disks item eld, press <Enter> to select the hard disk drives that you want to

include in the RAID set.

5. Use the up/down arrow keys to move the selection bar then press <Space> to select a

disk. A small triangle before the Port number marks the selected drive. Press <Enter>

when you are done.

[ESC]-Previous Menu [ENTER]-Select[ ]Change

Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023

[ CREATE VOLUME MENU ]

[ HELP ]

Name:

RAID Level:

Disks:

Strip Size:

Capacity:

Syne:

Create Volume

Enter a unique volume name that has no special characters and is

16 characters or less.

Volume0

RAID0(Strips)

Select Disks

128KB

0.0 GB

N/A

[TAB]-Next

[ SELECT DISKS ]

Port Drive Model Serial # Size Status

0 ST3300656SS HWAS0000991753TR 279.3GB Non-RAID Disk

1 ST3300656SS 37VN00009846RAJ1 279.3GB Non-RAID Disk

2 ST3300656SS 397600009846UEDY 279.3GB Non-RAID Disk

3 ST3300656SS GWC50000991756G6 279.3GB Non-RAID Disk

Select 1 Master and 1 Recovery disk to create volume.

[ ]-Prev/Next [TAB]-(M)aster [SPACE]-(R)ecovery [ENTER]-Done

5-6 Chapter 5: RAID Conguration

6. Use the up/down arrow keys to select the stripe size for the RAID array (for RAID 0,

10 and 5 only) then press <Enter>. The available stripe size values range from 4 KB to

128 KB. The following are typical values:

RAID 0: 128KB

RAID 10: 64KB

RAID 5: 64KB

We recommend a lower stripe size for server systems, and a higher stripe size for

multimedia computer systems used mainly for audio and video editing.

7. In the Capacity eld item, key in the RAID volume capacity that you want to use and

press <Enter>. The default value eld indicates the maximum allowed capacity.

8. Press <Enter> to start creating the RAID volume.

9. From the following warning message, press <Y> to create the RAID volume and return

to the main menu, or press <N> to go back to the CREATE VOLUME menu.

WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.

Are you sure you want to create this volume? (Y/N):

ASUS TS100-E10-PI4 5-7

5.2.2 Deleting a RAID set

Take caution when deleting a RAID set. You will lose all data on the hard disk drives when

you delete a RAID set.

To delete a RAID set:

1. From the utility main menu, select 2. Delete RAID Volume and press <Enter>.

2. From the Delete Volume Menu, press the up/down arrow keys to select the RAID set

you want to delete then press <Del>.

3. Press <Y> to conrm deletion of the selected RAID set and return to the utility main

menu, or press <N> to return to the DELETE VOLUME menu.

[ESC]-Previous Menu[ ]-Select

Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023

[ DELETE VOLUME MENU ]

[ HELP ]

Deleting a volume will reset the disks to non-RAID

WARNING: ALL DISK DATA WILL BE DELETED.

(This does not apply to Recovery volumes)

[DEL]-Delete Volume

Name Level Drives Capacity Status Bootable

Volume0 RAID0(Stripe) 2 298.0GB Normal Yes

ALL DATA IN THE VOLUME WILL BE LOST!

(This does not apply to Recovery volumes)

Are you sure you want to delete volume “Volume0”? (Y/N):

[ DELETE VOLUME VERIFICATION ]

5-8 Chapter 5: RAID Conguration

5.2.3 Resetting disks to Non-RAID

Take caution before you reset a RAID volume hard disk drive to non-RAID. Resetting a

RAID volume hard disk drive deletes all internal RAID structure on the drive.

To reset a RAID set:

1. From the utility main menu, select 3. Reset Disks to Non-RAID and press <Enter>.

2. Press the up/down arrow keys to select the drive(s) or disks of the RAID set you want

to reset, then press <Space>. A small triangle before the Port number marks the

selected drive. Press <Enter> when you are done.

3. Press <Y> in the conrmation window to reset the drive(s) or press <N> to return to the

utility main menu.

Port Drive Model Serial # Size Status

0 ST3300656SS HWAS0000991753TR 279.3GB Member Disk

1 ST3300656SS 37VN00009846RAJ1 279.3GB Member Disk

Select the disks that should be reset.

Resetting RAID disk will remove its RAID structures

and revert it to a non-RAID disk.

[ ]-Previous/Next [SPACE]-Selects [ENTER]-Selection Complete

[ RESET RAID DATA ]

WARNING: Resetting a disk causes all data on the disk to be lost.

(This does not apply to Recovery volumes)

ASUS TS100-E10-PI4 5-9

Select a destination disk with the same size as the original hard disk.

5.2.5 Rebuilding the RAID

This option is only for the RAID 1 set.

Rebuilding the RAID with other non-RAID disk

If any of the SATA hard disk drives included in the RAID 1 array failed, the system displays

the status of the RAID volume as “Degraded” during POST. You can rebuild the RAID array

with other installed non-RAID disks.

To rebuild the RAID with other non-RAID disk:

1. During POST, press <Ctrl>+<I> at the prompt to enter the Intel Rapid Storage

Technology option ROM utility.

2. If there is a non-RAID SATA Hard Disk available, the utility will prompt you to rebuild

the RAID. Press the up/down arrow keys to select the destination disk then Press

<Enter> to start the rebuilding process, or press <ESC> to exit.

5.2.4 Exiting the Intel® Rapid Storage Technology enterprise

SATA Option ROM utility

To exit the utility:

1. From the utility main menu, select 4. Exit then press <Enter>.

2. Press <Y> to exit or press <N> to return to the utility main menu.

Select the port of destination disk for rebuilding (ESC to exit):

Port Drive Model Serial # Size

X XXXXXXXXXXX XXXXXXXX XXX.GB

“Degraded” volume and disk available for rebuilding detected. Selectign

a disk initiates a rebuild. Rebuild completes in the operating system.

[ ]-Previous/Next [ENTER]-Select [ESC]-Exit

[ DEGRADED VOLUME DETECTED ]

Are you sure you want to exit? (Y/N):

[ CONFIRM EXIT ]

5-10 Chapter 5: RAID Conguration

3. The utility immediately starts rebuilding after the disk is selected. When done, the

status of the degraded RAID volume is changed to “Rebuild”.

4. Press <Esc> to exit Intel Rapid Storage Technology and reboot the system.

5. Select Start > Programs > Intel Rapid Storage > Intel Rapid Storage Console or

click the Intel Rapid Storage Technology tray icon to load the Intel Rapid Storage

Manager utility.

6. From the View menu, select Advanced Mode to display the details of the Intel Rapid

Storage Console.

7. From the Volumes view option, select RAID volume to view the rebuilding status.

When nished, the status is changed to “Normal”.

Rebuilding the RAID with a new hard disk

If any of the SATA hard disk drives included in the RAID array failed, the system displays the

status of the RAID volume as “Degraded” during POST. You may replace the disk drive and

rebuild the RAID array.

To rebuild the RAID with a new hard disk:

1. Remove the failed SATA hard disk and install a new SATA hard disk of the same

specication into the same SATA Port.

Select a destination disk with the same size as the original hard disk.

2. Reboot the system then follow the steps in section Rebuilding the RAID with other

non-RAID disk.

[ESC]-Exit [ENTER]-Select Menu[ ]-Select

Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023

[ MAIN MENU ]

[ DISK/VOLUME INFORMATION]

RAID Volumes: *=Data is Encrypted

ID Name Level1 Strip Size Status Bootable

1 Volume0 RAID1(Mirror) N/A 149.0GB Rebuild Yes

Physical Devices:

Port Drive Model Serial # Size Type/Status(Vol ID)

1 ST3160812AS 9LS0F4HL 149.0GB Member Disk(0)

2 ST3160812AS 3LS0JYL8 149.0GB Member Disk(0)

Volumes with “Rebuild” status will be rebuilt within the operating system.

3. Reset Disks to Non-RAID

4. Exit

1. Create RAID Volume

2. Delete RAID Volume

ASUS TS100-E10-PI4 5-11

5.2.6 Setting the Boot array in the BIOS Setup Utility

You can set the boot priority sequence in the BIOS for your RAID arrays when creating multi-

RAID using the Intel® Rapid Storage Technology enterprise SATA Option ROM utility.

To set the boot array in the BIOS:

Set at least one of the arrays bootable to boot from the hard disk.

1. Reboot the system and press <Del> to enter the BIOS setup utility during POST.

2. Go to the Boot menu and select the boot option priority.

3. Use up/down arrow keys to select the boot priority and press <Enter>. See the Boot

menu section of Chapter 4 for more details.

4. From the Exit menu, select Save Changes & Exit, then press <Enter>.

5. When the conrmation window appears, select Yes, then press <Enter>.

5-12 Chapter 5: RAID Conguration

5.3 Intel® Rapid Storage Technology enterprise

(Windows)

The Intel® Rapid Storage Technology enterprise allows you to create RAID 0, RAID 1, RAID

10 (RAID 1+0), and RAID 5 set(s) from Serial ATA hard disk drives that are connected to the

Serial ATA connectors supported by the Southbridge.

You can click Rescan to re-scan any attached hard disks.

1. Turn on the system and go to the windows desktop.

2. Click the Intel® Rapid Storage Technology enterprise icon to display the main menu.

Your storage system is congured for data protection, increased performance and

optimal data storage capacity. You can create additional volumes to further optimize

your storage system.

To enter the Intel® Rapid Storage Technology enterprise utility under Windows operating

system:

You need to manually install the Intel® Rapid Storage Technology enterprise utility on a

Windows® operating system. Please refer to the installation instructions in Chapter 6.

ASUS TS100-E10-PI4 5-13

5.3.1 Creating a RAID set

To create a RAID set:

1. From the utility main menu, select Create Volume and select volume type.

2. Click Next.

3. Enter a name for the RAID set, then select the array disks.

4. Select Volume Size tab, you can drag the bar to decide the volume size.

5. Click Next.

• If you do not want to keep the data on one of the selected disks, select NO when

prompted.

• If you want to Enable volume write-back cache or Initialize volume, click

Advanced.

5-14 Chapter 5: RAID Conguration

6. Conrm the volume creation, than click Create Volume to continue.

This process could take a while depending on the number and size of the disks. You can

continue using other applications during this time.

7. Wait until the process is completed, then click OK when prompted.

You still need to partition your new volume using Windows Disk Management before

adding any data.

The RAID set is displayed in the Volumes list and you can change the settings in

Volume Properties.

ASUS TS100-E10-PI4 5-15

5.3.2 Changing a Volume Type

To change the volume type in Volume Properties:

1. Click the SATA array items you want to change in Volumes eld.

2. From the Volume Properties eld, select Type:RAID 1 Change type.

We recommend a lower stripe size for server systems, and a higher stripe size for

multimedia computer systems used mainly for audio and video editing.

3. You can change the Name, Select the new volume type, and Select additional

disks to include in the new volume if needed.

4. Select the Data stripe size for the RAID array (for RAID 0, 10 and 5 only), and click

OK. The available stripe size values range from 4 KB to 128 KB. The following are

typical values:

RAID 0: 128KB

RAID 10: 64KB

RAID 5: 64KB

5-16 Chapter 5: RAID Conguration

5.3.3 Deleting a volume

Be cautious when deleting a volume. You will lose all data on the hard disk drives. Before

you proceed, ensure that you back up all your important data from your hard drives.

To delete a volume:

1. From the utility main menu, select the volume (exp. Volume_0000) in Volumes eld

you want to delete.

3. Click Yes to delete the volume and return to the utility main menu, or click No to return

to the main menu.

2. Select Delete volume in Volume Properties eld. The following screen appears.

ASUS TS100-E10-PI4 5-17

5.3.4 Preferences

System Preferences

Allow you to set to show the notication area icon and show system information, warning, or

errors here.

E-Mail Preferences

Allow you to set to sent e-mail of the following events:

• Storage system information

• Storage system warnings

• Storage system errors

5-18 Chapter 5: RAID Conguration

Driver Installation

This chapter provides the instructions for installing the

necessary drivers for different system components.

Chapter 6: Driver Installation

6-2 Chapter 6: Driver Installation

6.1 RAID driver installation

After creating the RAID sets for your server system, you are now ready to install an

operating system to the independent hard disk drive or bootable array. This part provides the

instructions on how to install the RAID controller drivers during OS installation.

6.1.1 CreatingaUSBashdrivewithRAIDdrive

When installing Windows® Server OS, you can load the RAID driver from a USB ash drive.

You can create a USB ash drive with RAID driver in Windows by copying the les from the

support DVD to the USB ash drive.

To copy the RAID driver to a USB ash drive in Windows environment:

1. Place the motherboard support DVD in the optical drive.

2. Connect a USB ash drive to your system.

3. Click on the optical drive to browse the contents of the support DVD.

4. Click Drivers > C24x INTEL RAID > Driver > Windows and then copy the RAID driver

folder to the USB ash drive.

6.1.2 InstallingtheRAIDcontrollerdriver

DuringWindows® Server 2012 R2 or 2016 OS installation

To install the RAID controller driver when installing Windows® Server OS:

1. Boot the computer using the Windows® Server installation disc. Follow the onscreen

instructions to start installing Windows® Server.

2. When prompted to choose a type of installation, click Custom:InstallWindowsonly

(advanced).

ASUS TS100-E10-PI4 6-3

3. Click Load Driver.

4. A message appears reminding you to insert the installation media containing the driver of

the RAID controller driver (the installation media can be a CD, DVD, or USB ash drive).

• If you have only one optical drive installed in your system, eject the Windows OS

installation disc and replace with the motherboard Support DVD into the optical

drive.

• Or you may connect a USB ash drive containing the RAID controller driver.

Click Browse to continue.

5. Locate the driver in the corresponding folder of the Support DVD or USB ash drive

and then click OK to continue.

6. Select the RAID controller driver you need from the list and click Next.

6-4 Chapter 6: Driver Installation

7. When the system nishes loading the RAID driver,

• Replace the motherboard Support DVD with the Windows Server installation disc.

• Remove the USB ash drive.

Select the drive to install Windows and click Next.

8. Setup then proceeds with the OS installation. Follow the onscreen instructions to

continue.

ASUS TS100-E10-PI4 6-5

6.2 Managementapplicationsandutilitiesinstallation

When you place the support DVD into the optical drive, the DVD automatically displays the

main screen if Autorun is enabled in your computer. By default, the Drivers tab is displayed.

If Autorun is NOT enabled in your computer, browse the contents of the support DVD to

locate the le Setup.exe. Double-click the Setup.exe to run the support DVD.

6.3 RunningtheSupportDVD

• The contents of the support DVD are subject to change at any time without notice.

Visit the ASUS website (www.asus.com) for the latest updates on software and

utilities.

• The support DVD is supported on Windows® Server 2012 R2 and Windows® Server

2016.

The support DVD that is bundled with your motherboard contains drivers, management

applications, and utilities that you can install to maximize the features of your motherboard.

Onscreen display and content vary depending on the motherboard and chipset. The

screenshots are provided for reference only.

6-6 Chapter 6: Driver Installation

6.4 Installingthesystemdrivers

This section provides the instructions on how to install the system drivers. You will need to

manually install the system drivers on a Windows® operating system.

To install the system drivers:

1. Restart the computer, and then log on with Administrator privileges.

2. Insert the support DVD into the optical drive. The support DVD automatically displays

the Driver menu if Autorun is enabled in your computer.

If Autorun is NOT enabled in your computer, browse the contents of the support DVD to

locate the le Setup.exe. Double-click the Setup.exe to run the support DVD.

3. Check the drivers that you would like to install, then select Install.

4. The installation window appears.

ASUS TS100-E10-PI4 6-7

5. Follow the onscreen instructions to complete the installation.

6-8 Chapter 6: Driver Installation

Appendix

This appendix includes additional information that you may refer

to when conguring the motherboard.

Appendix

A-2 Appendix

P11C-X/AUDIO block diagram

ASUS TS100-E10-PI4 A-3

Q-Code table

(continued on the next page)

Code Description

00 Not used

02 microcode

03 CACHE_ENABLED

04 PCH initialization

06 CPU_EARLY_INIT

10 PEI Core is started

11 – 14 Pre-memory CPU initialization is started

15 – 18 Pre-memory System Agent initialization is started

19 – 1C Pre-memory PCH initialization is started

2B – 2F Memory initialization

30 Reserved for ASL (see ASL Status Codes section below)

31 Memory Installed

32 – 36 CPU post-memory initialization

37 – 3A Post-Memory System Agent initialization is started

3B – 3E Post-Memory PCH initialization is started

4F DXE IPL is started

50 – 53 Memory initialization error. Invalid memory type or incompatible memory

speed

4F DXE IPL is started

54 Unspecied memory initialization error

55 Memory not installed

56 Invalid CPU type or Speed

57 CPU mismatch

58 CPU self test failed or possible CPU cache error

59 CPU micro-code is not found or micro-code update is failed

5A Internal CPU error

5B Reset PPI is not available

5C – 5F Reserved for future AMI error codes

E0 S3 Resume is stared (S3 Resume PPI is called by the DXE IPL)

E1 S3 Boot Script execution

E2 Video repost

E3 OS S3 wake vector call

E4 – E7 Reserved for future AMI progress codes

E8 S3 Resume Failed

E9 S3 Resume PPI not Found

EA S3 Resume Boot Script Error

EB S3 OS Wake Error

EC – EF Reserved for future AMI error codes

F0 Recovery condition triggered by rmware (Auto recovery)

F1 Recovery condition triggered by user (Forced recovery)

F2 Recovery process started

F3 Recovery rmware image is found

F4 Recovery rmware image is loaded

F5 – F7 Reserved for future AMI progress codes

F8 Recovery PPI is not available

F9 Recovery capsule is not found

A-4 Appendix

Code Description

FA Invalid recovery capsule

FB – FF Reserved for future AMI error codes

60 DXE Core is started

61 NVRAM initialization

62 Installation of the PCH Runtime Services

63 – 67 CPU DXE initialization is started

68 PCI host bridge initialization

69 System Agent DXE initialization is started

6A System Agent DXE SMM initialization is started

6B – 6F System Agent DXE initialization (System Agent module specic)

70 PCH DXE initialization is started

71 PCH DXE SMM initialization is started

72 PCH devices initialization

73 – 77 PCH DXE Initialization (PCH module specic)

78 ACPI module initialization

79 CSM initialization

7A – 7F Reserved for future AMI DXE codes

90 Boot Device Selection (BDS) phase is started

91 Driver connecting is started

92 PCI Bus initialization is started

93 PCI Bus Hot Plug Controller Initialization

94 PCI Bus Enumeration

95 PCI Bus Request Resources

96 PCI Bus Assign Resources

97 Console Output devices connect

98 Console input devices connect

99 Super IO Initialization

9A USB initialization is started

9B USB Reset

9C USB Detect

9D USB Enable

9E – 9F Reserved for future AMI codes

A0 IDE initialization is started

A1 IDE Reset

A2 IDE Detect

A3 IDE Enable

A4 SCSI initialization is started

A5 SCSI Reset

A6 SCSI Detect

A7 SCSI Enable

A8 Setup Verifying Password

A9 Start of Setup

AA Reserved for ASL (see ASL Status Codes section below)

AB Setup Input Wait

(continued on the next page)

ASUS TS100-E10-PI4 A-5

Code Description

AC Reserved for ASL (see ASL Status Codes section below)

AD Ready To Boot event

AE Legacy Boot event

AF Exit Boot Services event

B0 Runtime Set Virtual Address MAP Begin

B1 Runtime Set Virtual Address MAP End

B2 Legacy Option ROM Initialization

B3 System Reset

B4 USB hot plug

B5 PCI bus hot plug

B6 Clean-up of NVRAM

B7 Conguration Reset (reset of NVRAM settings)

B8– BF Reserved for future AMI codes

D0 CPU initialization error

D1 System Agent initialization error

D2 PCH initialization error

D3 Some of the Architectural Protocols are not available

D4 PCI resource allocation error. Out of Resources

D5 No Space for Legacy Option ROM

D6 No Console Output Devices are found

D7 No Console Input Devices are found

D8 Invalid password

D9 Error loading Boot Option (LoadImage returned error)

DA Boot Option is failed (StartImage returned error)

DB Flash update is failed

DC Reset protocol is not available

ACPI/ASL Checkpoints (under OS)

Code Description

03 System is entering S3 sleep state

04 System is entering S4 sleep state

05 System is entering S5 sleep state

30 System is waking up from the S3 sleep state

40 System is waking up from the S4 sleep state

AC System has transitioned into ACPI mode. Interrupt controller is in PIC mode.

AA System has transitioned into ACPI mode. Interrupt controller is in APIC mode.

A-6 Appendix

Notices

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

• This device may not cause harmful interference.

• This device must accept any interference received including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

The use of shielded cables for connection of the monitor to the graphics card is required

to assure compliance with FCC regulations. Changes or modications to this unit not

expressly approved by the party responsible for compliance could void the user’s authority

to operate this equipment.

Compliance Statement of Innovation, Science and Economic

Development Canada (ISED)

This device complies with Innovation, Science and Economic Development Canada licence

exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device

may not cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

CAN ICES-3(A)/NMB-3(A)

Déclaration de conformité de Innovation, Sciences et

Développement économique Canada (ISED)

Le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement

économique Canada applicables aux appareils radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage,

et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le fonctionnement.

CAN ICES-3(A)/NMB-3(A)

ASUS TS100-E10-PI4 A-7

Japan statement notice

This product cannot be directly connected to the Internet (including public wireless LAN) of a

telecom carrier (mobile network companies, landline network companies, Internet providers,

etc.). When connecting this product to the Internet, be sure to connect it through a router or

switch.

Australia statement notice

From 1 January 2012 updated warranties apply to all ASUS products, consistent with the

Australian Consumer Law. For the latest product warranty details please visit

https://www.asus.com/support/. Our goods come with guarantees that cannot be excluded

under the Australian Consumer Law. You are entitled to a replacement or refund for a major

failure and compensation for any other reasonably foreseeable loss or damage. You are also

entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality

and the failure does not amount to a major failure.

If you require assistance please call ASUS Customer Service 1300 2787 88 or visit us at

https://www.asus.com/support/.

Declaration of compliance for product environmental regulation

ASUS follows the green design concept to design and manufacture our products, and

makes sure that each stage of the product life cycle of ASUS product is in line with global

environmental regulations. In addition, ASUS disclose the relevant information based on

regulation requirements.

Please refer to http://csr.asus.com/Compliance.htm for information disclosure based on

regulation requirements ASUS is complied with:

EU REACH and Article 33

Complying with the REACH (Registration, Evaluation, Authorization, and Restriction of

Chemicals) regulatory framework, we publish the chemical substances in our products at

ASUS REACH website at http://csr.asus.com/english/REACH.htm.

EU RoHS

This product complies with the EU RoHS Directive. For more details, see

http://csr.asus.com/english/article.aspx?id=35

Japan JIS-C-0950 Material Declarations

Information on Japan RoHS (JIS-C-0950) chemical disclosures is available on

http://csr.asus.com/english/article.aspx?id=19

DO NOT throw the motherboard in municipal waste. This product has been designed to

enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin

indicates that the product (electrical and electronic equipment) should not be placed in

municipal waste. Check local regulations for disposal of electronic products.

DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol

of the crossed out wheeled bin indicates that the battery should not be placed in municipal

waste.

A-8 Appendix

India RoHS

This product complies with the “India E-Waste (Management) Rules, 2016” and prohibits

use of lead, mercury, hexavalent chromium, polybrominated biphenyls (PBBs) and

polybrominated diphenyl ethers (PBDEs) in concentrations exceeding 0.1% by weight in

homogenous materials and 0.01% by weight in homogenous materials for cadmium, except

for the exemptions listed in Schedule II of the Rule.

Vietnam RoHS

ASUS products sold in Vietnam, on or after September 23, 2011,meet the requirements of

the Vietnam Circular 30/2011/TT-BCT.

Các sản phẩm ASUS bán tại Việt Nam, vào ngày 23 tháng 9 năm2011 trở về sau, đều phải đáp ứng

các yêu cầu của Thông tư 30/2011/TT-BCT của Việt Nam.

Turkey RoHS

AEEE Yönetmeliğine Uygundur

ASUS Recycling/Takeback Services

ASUS recycling and takeback programs come from our commitment to the highest standards

for protecting our environment. We believe in providing solutions for you to be able to

responsibly recycle our products, batteries, other components as well as the packaging

materials. Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling

information in different regions.

Ecodesign Directive

European Union announced a framework for the setting of ecodesign requirements for

energy-related products (2009/125/EC). Specic Implementing Measures are aimed at

improving environmental performance of specic products or across multiple product types.

ASUS provides product information on the CSR website. The further information could be

found at https://csr.asus.com/english/article.aspx?id=1555.

ASUS TS100-E10-PI4 A-9

ASUS contact information

ASUSTeK COMPUTER INC.

Address 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112, Taiwan

Telephone +886-2-2894-3447

Fax +886-2-2890-7798

Web site https://www.asus.com

Technical Support

Telephone +86-21-38429911

Online Support https://www.asus.com/support/Product/ContactUs/Services/

questionform/?lang=en

ASUSTeK COMPUTER INC. (Taiwan)

Address 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112, Taiwan

Telephone +886-2-2894-3447

Fax +886-2-2890-7798

Web site https://www.asus.com/tw/

Technical Support

Telephone +886-2-2894-3447 (0800-093-456)

Online Support https://www.asus.com/support/Product/ContactUs/Services/

questionform/?lang=zh-tw

ASUSTeK COMPUTER INC. (China)

Address No. 5077, Jindu Road, Minhang District, Shanghai, China

Telephone +86-21-5442-1616

Fax +86-21-5442-0099

Web site https://www.asus.com.cn

Technical Support

Telephone +86-20-2804-7506 (400-620-6655)

Online Support https://www.asus.com/support/Product/ContactUs/Services/

questionform/?lang=zh-cn

A-10 Appendix

ASUS contact information

ASUS COMPUTER INTERNATIONAL (America)

Address 48720 Kato Rd., Fremont, CA 94538, USA

Fax +1-510-608-4555

Web site https://www.asus.com/us/

Technical Support

Support fax +1-812-284-0883

General support +1-812-282-2787

Online support https://www.asus.com/support/Product/ContactUs/Services/

questionform/?lang=en-us

ASUS COMPUTER GmbH (Germany and Austria)

Address Harkortstrasse 21-23, 40880 Ratingen, Germany

Web site https://www.asus.com/de/

Technical Support

Telephone (DE) +49-2102-5789557

Telephone (AT) +43-1360-2775461

Online support https://www.asus.com/support/Product/ContactUs/Services/

questionform/?lang=de-de

ASUS Czech Service s.r.o. (Europe)

Address Na Rovince 887, 720 00 Ostrava – Hrabová,

Czech Republic

Telephone +420-596766888

Web site https://www.asus.com/cz/

Technical Support

Telephone +420-596-766-891

Fax +420-596-766-329

E-mail advance.rma.eu@asus.com

Online Support https://www.asus.com/support/Product/ContactUs/Services/

questionform/?lang=cs-cz

ASUS TS100-E10-PI4 A-11

ASUS contact information

ASUS Holland BV (The Netherlands)

Address Marconistraat 2, 7825GD EMMEN, The Netherlands

Web site https://www.asus.com/nl/

Technical Support

Telephone +31-(0)591-5-70292

Fax +31-(0)591-666853

E-mail advance.rma.eu@asus.com

Online Support https://www.asus.com/support/Product/ContactUs/Services/

questionform/?lang=nl-nl

ASUS Polska Sp. z o.o. (Poland)

Address Ul. Postępu 6, 02-676 Warszawa, Poland

Web site https://www.asus.com/pl/

Technical Support

Telephone +48-225718033

Online Support https://www.asus.com/support/Product/ContactUs/Services/

questionform/?lang=pl-pl

ASK-Service (Russia and CIS)

Address

г.Москва, ул. Орджоникидзе, д.10, Россия

Telephone (495) 640-32-75

Web site https://www.asus.com/ru/

Technical Support

Telephone 008-800-100-ASUS (008-800-100-2787)

Online Support https://www.asus.com/support/Product/ContactUs/Services/

questionform/?lang=ru-ru

A-12 Appendix

Table of Contents

ASUS TS100-E10-PI4 User Manual

Related Manuals