ASUS UN42-M088Y User Manual

Displayed below is the user manual for UN42-M088Y by ASUS which is a product in the PCs/Workstations category. This manual has pages.

Related Manuals

ASUS ASUS Rampage IV GENE Manual

ASUS ASUS X99-DELUXE II Manual

ASUS ASUS MCI-10G/X550-2T Manual

ASUS UX435EAL-KC096T Manual

ASUS PN62S-B3519ZD Manual

ASUS VE228H Manual

ASUS RS700DA-E6/PS4 Manual

ASUS PCE-N15 Manual

VivoMini

UN Series

User Manual

No part of this manual, including the products and software described in it, may be

reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any

language in any form or by any means, except documentation kept by the purchaser for

backup purposes, without the express written permission of ASUSTeK COMPUTER INC.

(“ASUS”).

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS

OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS,

ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,

LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN

IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY

DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

Products and corporate names appearing in this manual may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identication or

explanation and to the owners’ benet, without intent to infringe.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR

INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,

AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO

RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS

MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

LIMITATION OF LIABILITY

Circumstances may arise where because of a default on ASUS’ part or other liability, you

are entitled to recover damages from ASUS. In each such instance, regardless of the basis

on which you are entitled to claim damages from ASUS, ASUS is liable for no more than

damages for bodily injury (including death) and damage to real property and tangible

personal property; or any other actual and direct damages resulted from omission or failure of

performing legal duties under this Warranty Statement, up to the listed contract price of each

product.

ASUS will only be responsible for or indemnify you for loss, damages or claims based in

contract, tort or infringement under this Warranty Statement.

This limit also applies to ASUS’ suppliers and its reseller. It is the maximum for which ASUS, its

suppliers, and your reseller are collectively responsible.

UNDER NO CIRCUMSTANCES IS ASUS LIABLE FOR ANY OF THE FOLLOWING: (1) THIRD-

PARTY CLAIMS AGAINST YOU FOR DAMAGES; (2) LOSS OF, OR DAMAGE TO, YOUR RECORDS

OR DATA; OR (3) SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY ECONOMIC

CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR SAVINGS), EVEN IF ASUS, ITS

SUPPLIERS OR YOUR RESELLER IS INFORMED OF THEIR POSSIBILITY.

SERVICE AND SUPPORT

Visit our multi-language web site at http://support.asus.com

Revised Edition V2

September 2014

E9802

VivoMini UN Series

Contents

About this manual ............................................................................................. 4

Conventions used in this manual ............................................................... 4

Typography ......................................................................................................... 4

Package contents ............................................................................................... 5

Getting to know your VivoMini 7

Features ................................................................................................................. 8

Front panel .......................................................................................................... 8

Left side ............................................................................................................... 9

Rear panel .........................................................................................................10

Using your VivoMini 13

Getting started .................................................................................................. 14

Connecting the AC power adapter ..........................................................14

Connecting a display panel ........................................................................16

Connecting USB keyboard or mouse ......................................................17

Turning on your VivoMini ............................................................................17

Turning off your VivoMini ..............................................................................18

Putting your VivoMini to sleep .................................................................... 18

Entering the BIOS Setup ................................................................................18

Quickly enter the BIOS .................................................................................. 18

Memory upgrade 19

Upgrading memory modules ...................................................................... 20

Appendix 27

Safety information ...........................................................................................28

Setting up your system.................................................................................28

Care during use ...............................................................................................28

Regulatory notices ...........................................................................................30

ASUS contact information ............................................................................36

VivoMini UN Series

About this manual

This manual provides information about the hardware and software

features of your PC, organized through the following chapters:

Chapter 1: Getting to know your VivoMini

This chapter details the hardware components of your VivoMini.

Chapter 2: Using your VivoMini

This chapter provides you with information on using your

VivoMini.

Chapter 3: Memory upgrade

This chapter provides you with information on how to install

new memory modules to your VivoMini.

Appendices

This section includes notices and safety statements your

VivoMini.

Conventions used in this manual

To highlight key information in this manual, some text are presented

as follows:

IMPORTANT! This message contains vital information that must be

followed to complete a task.

NOTE: This message contains additional information and tips that

can help complete tasks.

WARNING! This message contains important information that must

be followed to keep you safe while performing certain tasks and

prevent damage to your VivoMini's data and components.

Typography

Bold text Indicates a menu or an item to select.

Italic

This indicates sections that you can refer

to in this manual.

VivoMini UN Series

Package contents

NOTES:

• *Actualproductspecicationsandpackagecontentsmay

vary depending on the model type, country, or region.

• **Theavailabilityandquantityoftheseitemsvarywithyour

VivoMini package.

• Ifthedeviceoranyofitscomponentsfailormalfunction

during normal or proper use and it is still within the warranty

period, bring the device and the warranty card to you

nearest ASUS Service Center.

Your VivoMini package contains the following items:

VivoMini

Powercable*

Technical documentations

ACpoweradapter*

DriverDVD**

DisplayPorttoVGAadapter**

VivoMini UN Series

Getting to know your VivoMini

VivoMini UN Series

ASUS VivoMini

Features

Front panel

Drive activity indicator

This indicator lights up when your VivoMini is accessing the

internal storage drive.

Power button

The power button allows you to turn the VivoMini on or

o. You can also press the power button once to put your

VivoMini to sleep mode.

VivoMini UN Series

Left side

Kensington® security slot

The Kensington security slot allows you to secure your

VivoMini using Kensington® security products.

Memory card slot

The built-in memory card reader enables your VivoMini

to read and write data to and from SD/SDHC/SDXC/MMC

cards.

NOTE: The actual transfer speed may depend on the

memory card specications.

USB 3.0 ports

These USB (Universal Serial Bus) 3.0 ports provide a transfer

rate of up to 5Gbit/s and are backward compatible with

USB 2.0. These ports also support the Battery Charging 1.2

technology that allows you to charge your USB devices.

VivoMini UN Series

Air vents

The air vents allow warm air to exit your VivoMini chassis.

NOTE: The air vents found on the bottom side of

your VivoMini allow cool air to enter your device. It is

recommended that you place your VivoMini on a at

stable surface for optimum air ventilation.

IMPORTANT! For optimum heat dissipation and air

ventilation, ensure that the air vents are free from

obstructions.

Power input (DC 19V)

The supplied power adapter converts AC power to DC

power for use with this jack. Power supplied through this

jack supplies power to the VivoMini. To prevent damage to

the VivoMini, always use the bundled power adapter.

WARNING! The power adapter may become warm

to hot when in use. Do not cover the adapter and

keep it away from your body.

Rear panel

VivoMini UN Series

HDMI port

The HDMI (High Denition Multimedia Interface) port

supports a Full-HD device such as an LCD TV or monitor to

allow viewing on a larger external display.

DisplayPort

The DisplayPort sends high-performance digital output

from your VivoMini to a display device such as an LCD TV

or HD monitor.

USB 3.0 ports

These USB (Universal Serial Bus) 3.0 ports provide a

transfer rate of up to 5Gbit/s and are backward compatible

with USB 2.0.

LAN port

The 8-pin RJ-45 LAN port supports a standard Ethernet

cable for connection to a local network.

Headphone output/microphone input combo jack

port

This port allows you to connect your VivoMini to amplied

speakers or headphones. You can also use this port to

connect your VivoMini to an external microphone.

VivoMini UN Series

Using your VivoMini

VivoMini UN Series

Getting started

Connecting the AC power adapter

To connect the AC power adapter to your VivoMini:

A. Connect the AC power cord to the AC/DC adapter.

B. Plug the AC power cord into a 100 V~240 V power source.

C. Connect the DC power connector into your VivoMini’s power

(DC) input port.

NOTE: The power adapter may vary in appearance depending on the

model or region.

VivoMini UN Series

NOTE:

Power adapter information:

• Inputvoltage:100Vac-240Vac

• Inputfrequency:50Hz-60Hz

• Ratingoutputcurrent:3.42A(65W)

• Ratingoutputvoltage:19V

IMPORTANT!

• WestronglyrecommendthatyouuseonlytheACpower

adapter and cable that came with your VivoMini.

• Westronglyrecommendthatyouuseagroundedwall

socket while using your VivoMini.

• Thesocketoutletmustbeeasilyaccessibleandnearyour

VivoMini.

• TodisconnectyourVivoMinifromitsmainpowersupply,

unplug your VivoMini from the power socket.

VivoMini UN Series

Connecting a display panel

You can connect a display panel or projector to your VivoMini that

has the following connectors:

• HDMIconnector

• DisplayPortconnector

• VGAconnector(usewithaDisplayPorttoVGAadapterorHDMI

to VGA adapter)

• DVIconnector(usewithaDisplayPorttoDVIadapterorHDMI

to DVI adapter)

NOTE: The DisplayPort to DVI adapter, HDMI to DVI adapter,

DisplayPort to VGA adapter, or HDMI to VGA adapter are each sold

separately.

To connect a display panel to your VivoMini:

Connect a display cable either to the HDMI or DisplayPort.

Connecting display via HDMI port

Connecting display via DisplayPort

VivoMini UN Series

Connecting USB keyboard or mouse

You can connect generally any USB keyboard and mouse to your

VivoMini. You can also connect a USB dongle for a wireless keyboard

and mouse set.

To connect a keyboard and mouse to your VivoMini:

Connect the USB cable from your keyboard and mouse to any of the

USB ports of your VivoMini.

NOTE: It is recommended that you use the USB ports on the rear

panel of the VivoMini when connecting a wired keyboard and mouse.

Turning on your VivoMini

Press the power button to turn on your VivoMini.

VivoMini UN Series

Turning off your VivoMini

If your VivoMini is unresponsive, press and hold the power button

for at least four (4) seconds until your VivoMini turns o.

Putting your VivoMini to sleep

To put your VivoMini on Sleep mode, press the Power button once.

Quickly enter the BIOS

ToquicklyentertheBIOS:

• Pressthepowerbuttonforatleastfour(4)secondstoshutdown

your VivoMini, then press the power button again to turn your

VivoMini back on, then press <F2> or <Del> during POST.

• WhenyourVivoMiniiso,disconnectthepowercordfromyour

VivoMini’s power connector. Reconnect the power cable and

press the power button to turn on your VivoMini. Press <F2> or

<Del> during POST.

NOTE: POST (Power-On Self Test) is a series of software controlled

diagnostic tests that run when you turn on your PC.

Entering the BIOS Setup

BIOS (Basic Input and Output System) stores system hardware

settings that are needed for system startup in the VivoMini.

In normal circumstances, the default BIOS settings apply to most

conditions to ensure optimal performance. Do not change the

default BIOS settings except in the following circumstances:

• Anerrormessageappearsonthescreenduringthesystem

bootupandrequestsyoutoruntheBIOSSetup.

• Youhaveinstalledanewsystemcomponentthatrequiresfurther

BIOS settings or update.

WARNING! Inappropriate BIOS settings may result to instability

or boot failure. We strongly recommend that you change the BIOS

settings only with the help of a trained service personnel.

Memory upgrade

VivoMini UN Series

Your VivoMini comes with two SO-DIMM memory slots that allow

you to install two 2 GB, 4 GB, or 8 GB unbuered with non-ECC 1.35 V

DDR3204-pinSO-DIMMsforamaximumof16GBmemory.

IMPORTANT!

• Itisrecommendedthatyoureplacethememorymodules

under professional supervision. Visit an ASUS service center for

further assistance.

• Refertohttp://www.asus.com for the list of compatible DIMMs.

You can only install 1.35 V DDR3 SO-DIMM to the VivoMini’s

DIMM slots.

To install or upgrade the memory modules:

1. Turn o your VivoMini then disconnect all cables and peripherals.

2. Place the VivoMini on a at stable surface, with its top side facing

down.

WARNING!

• Ensurethatyourhandsaredrybeforeproceedingwiththerest

of the installation process.

• Beforeinstallingmemorymodules,useagroundedwriststrap

or touch a safely grounded object or metal object to avoid

damaging them due to static electricity.

Upgrading memory modules

VivoMini UN Series

IMPORTANT! Take note of the orientation of the holed rubber foot

on the cover, and the number printed under each rubber foot. These

indicatethesequenceyoumustfollowwhenremovingtherubber

foot from its slot. Refer to the following illustration for details.

3. Using a at-head screwdriver or straightened paper clip, remove

the rubber feet from the bottom side then set them aside.

VivoMini UN Series

5. Get one screw from the ones you previously removed then

place it into the hole. Leave a portion of the screw head that

would be enough for you to hold.

4. Remove the four screws securing the cover.

VivoMini UN Series

6. Holdthescrewthengentlypulloutthecoverfromthebottom

side of the VivoMini. Use your other free hand to hold the

VivoMini in place.

VivoMini UN Series

7. Align and insert the memory module into the slot (A) and press

it down (B) until it is securely seated in place. Repeat the same

steps to install the other memory module.

IMPORTANT! Always install into the lower slot rst.

8. Remove the screw you previously attached on the bottom

cover (A), then align and insert the bottom cover back on your

VivoMini (B)

VivoMini UN Series

10. Replace the rubber feet back on each screw hole.

9. Reattach the screws to secure the cover back on the bottom

side of the main box.

IMPORTANT! Take note of the orientation of the holed rubber foot

on the cover, and the number printed under each rubber foot. These

indicatethesequenceyoumustfollowwhenreplacingtherubber

foot back into each slot. Refer to the following illustration for details.

VivoMini UN Series

Appendix

VivoMini UN Series

Safety information

Your VivoMini is designed and tested to meet the latest standards

ofsafetyforinformationtechnologyequipment.However,to

ensure your safety, it is important that you read the following safety

instructions.

Setting up your system

• Readandfollowallinstructionsinthedocumentationbeforeyou

operate your system.

• Donotusethisproductnearwateroraheatedsource.

• Setupthesystemonastablesurface.

• Openingsonthechassisareforventilation.Donotblockorcover

these openings. Make sure you leave plenty of space around the

system for ventilation. Never insert objects of any kind into the

ventilation openings.

• Usethisproductinenvironmentswithambienttemperatures

between 0˚C and 35˚C.

• Ifyouuseanextensioncord,makesurethatthetotalampere

rating of the devices plugged into the extension cord does not

exceed its ampere rating.

Care during use

• Donotwalkonthepowercordorallowanythingtorestonit.

• Donotspillwateroranyotherliquidsonyoursystem.

• Whenthesystemisturnedo,asmallamountofelectrical

current still ows. Always unplug the power cord from the power

outlets before cleaning the system.

• Ifyouencounterthefollowingtechnicalproblemswiththe

product,unplugthepowercordandcontactaqualiedservice

technician or your retailer.

– The power cord or plug is damaged.

 – Liquidhasbeenspilledintothesystem.

– The system does not function properly even if you follow

the operating instructions.

– The system was dropped or the cabinet is damaged.

– The system performance changes.

VivoMini UN Series

NO DISASSEMBLY

The warranty does not apply to the products that

have been disassembled by users

Lithium-Metal Battery Warning

CAUTION! Danger of explosion if battery is incorrectly

replaced.Replaceonlywiththesameorequivalenttype

recommended by the manufacturer. Dispose of used batteries

according to the manufacturer’s instructions.

DO NOT throw the VivoMini in municipal waste. This product has

been designed to enable proper reuse of parts and recycling. This

symbol of the crossed out wheeled bin indicates that the product

(electrical,electronicequipment,andmercury-containingbutton

cell battery) should not be placed in municipal waste. Check local

technical support services for product recycling.

VivoMini UN Series

Regulatory notices

REACH

Complying with the REACH (Registration, Evaluation, Authorization,

and Restriction of Chemicals) regulatory framework, we publish

the chemical substances in our products at ASUS REACH website at

http://csr.asus.com/english/REACH.htm

ASUS Recycling/Takeback Services

ASUS recycling and takeback programs come from our commitment

to the highest standards for protecting our environment. We believe

in providing solutions for you to be able to responsibly recycle our

products, batteries, other components, as well as the packaging

materials. Please go to http://csr.asus.com/english/Takeback.htm for

the detailed recycling information in dierent regions.

COATING NOTICE

IMPORTANT! To provide electrical insulation and maintain

electrical safety, a coating is applied to insulate the device except on

the areas where the I/O ports are located.

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

• Thisdevicemaynotcauseharmfulinterference,and

• Thisdevicemustacceptanyinterferencereceivedincluding

interference that may cause undesired operation.

Thisequipmenthasbeentestedandfoundtocomplywiththelimits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmfulinterferenceinaresidentialinstallation.Thisequipment

generates,usesandcanradiateradiofrequencyenergyand,ifnot

installed and used in accordance with manufacturer’s instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation.Ifthisequipmentdoescauseharmfulinterferenceto

VivoMini UN Series

radio or television reception, which can be determined by turning

theequipmentoandon,theuserisencouragedtotrytocorrect

the interference by one or more of the following measures:

• Reorientorrelocatethereceivingantenna.

• Increasetheseparationbetweentheequipmentandreceiver.

• Connecttheequipmenttoanoutletonacircuitdierentfrom

that to which the receiver is connected.

• Consultthedealeroranexperiencedradio/TVtechnicianfor

help.

CAUTION! Any changes or modications not expressly approved by

the grantee of this device could void the user’s authority to operate

theequipment.

RF exposure warning

Thisequipmentmustbeinstalledandoperatedinaccordancewith

provided instructions and the antenna(s) used for this transmitter

must be installed to provide a separation distance of at least 20

cm from all persons and must not be co-located or operating in

conjunction with any other antenna or transmitter. End-users and

installers must be provide with antenna installation instructions

and transmitter operating conditions for satisfying RF exposure

compliance.

Declaration of Conformity (R&TTE directive 1999/5/EC)

The following items were completed and are considered relevant

and sucient:

• Essentialrequirementsasin[Article3]

• Protectionrequirementsforhealthandsafetyasin[Article3.1a]

• Testingforelectricsafetyaccordingto[EN60950]

• Protectionrequirementsforelectromagneticcompatibilityin

[Article3.1b]

• Testingforelectromagneticcompatibilityaccordingto[EN301

489-1]&[EN301489-17]

• Eectiveuseoftheradiospectrumasin[Article3.2]

• Radiotestsuitesaccordingto[EN300328-2]

VivoMini UN Series

France Restricted Wireless Frequency Bands

SomeareasofFrancehavearestrictedfrequencyband.Theworst

case maximum authorized power indoors are:

• 10mWfortheentire2.4GHzband(2400MHz–2483.5MHz)

• 100mWforfrequenciesbetween2446.5MHzand2483.5MHz

NOTE: Channels10through13inclusiveoperateintheband2446.6

MHz to 2483.5 MHz.

There are few possibilities for outdoor use: On private property or on

the private property of public persons, use is subject to a preliminary

authorization procedure by the Ministry of Defense, with maximum

authorizedpowerof100mWinthe2446.5–2483.5MHzband.Use

outdoors on public property is not permitted.

In the departments listed below, for the entire 2.4 GHz band:

• Maximumauthorizedpowerindoorsis100mW

• Maximumauthorizedpoweroutdoorsis10mW

Departments in which the use of the 2400–2483.5 MHz band is

permitted with an EIRP of less than 100mW indoors and less than

10mW outdoors:

01 Ain 02 Aisne 03 Allier

05 Hautes Alpes 08 Ardennes 09 Ariège

11 Aude 12 Aveyron 16 Charente

24 Dordogne 25 Doubs 26 Drôme

32 Gers 36 Indre 37 Indre et Loire

41 Loir et Cher 45 Loiret 50 Manche

55 Meuse 58 Nièvre 59 Nord

60 Oise 61 Orne 63 Puy du Dôme

64 PyrénéesAtlantique 66 Pyrénées

Orientales

67 Bas Rhin

70 Haute Saône 71 Saône et Loire 75 Paris

82 Tarn et Garonne 84 Vaucluse 88 Vosges

89 Yonne 90 Territoire de

Belfort

94 Val de Marne

VivoMini UN Series

Thisrequirementislikelytochangeovertime,allowingyoutouse

your wireless LAN card in more areas within France. Please check

with ART for the latest information (www.art-telecom.fr)

NOTE: Your WLAN Card transmits less than 100mW, but more than

10mW.

Canadian Department of Communications Statement

This digital apparatus does not exceed the Class B limits for

radio noise emissions from digital apparatus set out in the

Radio Interference Regulations of the Canadian Department of

Communications.

This class B digital apparatus complies with Canadian ICES-003.

IC Radiation Exposure Statement for Canada

ThisequipmentcomplieswithICradiationexposurelimitssetforth

for an uncontrolled environment. To maintain compliance with IC

RFexposurecompliancerequirements,pleaseavoiddirectcontact

to the transmitting antenna during transmitting. End users must

follow the specic operating instructions for satisfying RF exposure

compliance.

Operation is subject to the following two conditions:

• Thisdevicemaynotcauseinterferenceand

• Thisdevicemustacceptanyinterference,includinginterference

that may cause undesired operation of the device.

VivoMini UN Series

CE Mark Warning

CE marking for devices without wireless LAN/Bluetooth

Theshippedversionofthisdevicecomplieswiththerequirements

of the EEC directives 2004/108/EC “Electromagnetic compatibility”

and2006/95/EC“Lowvoltagedirective”.

CE marking for devices with wireless LAN/ Bluetooth

ThisequipmentcomplieswiththerequirementsofDirective1999/5/

ECoftheEuropeanParliamentandCommissionfrom9March,1999

governingRadioandTelecommunicationsEquipmentandmutual

recognition of conformity.

Wireless Operation Channel for Dierent Domains

N.America2.412-2.462GHz Ch01throughCH11

Japan 2.412-2.484 GHz Ch01 through Ch14

Europe ETSI 2.412-2.472 GHz Ch01 through Ch13

VivoMini UN Series

ENERGY STAR complied product

ENERGY STAR is a joint program of the U.S.

Environmental Protection Agency and the U.S.

Department of Energy helping us all save money

and protect the environment through energy

ecient products and practices.

All ASUS products with the ENERGY STAR logo

comply with the ENERGY STAR standard, and the

power management feature is enabled by default. The monitor and

computer are automatically set to sleep after 10 and 30 minutes of

user inactivity. To wake your computer, click the mouse or press any

key on the keyboard.

Please visit http://www.energy.gov/powermanagement for

detail information on power management and its benets to the

environment. In addition, please visit http://www.energystar.gov for

detail information on the ENERGY STAR joint program.

NOTE: Energy Star is NOT supported on FreeDOS and Linux-based

products.

VivoMini UN Series

ASUS contact information

ASUSTeK COMPUTER INC.

Address  15Li-TeRoad,Peitou,Taipei,Taiwan11259

Telephone  +886-2-2894-3447

Fax   +886-2-2890-7798

E-mail info@asus.com.tw

Web site http://www.asus.com

Technical Support

Telephone  +86-21-3842-9911

Fax   +86-21-5866-8722,ext.9101#

Online support http://support.asus.com/techserv/techserv.aspx

ASUS COMPUTER INTERNATIONAL (America)

Address  800CorporateWay,Fremont,CA94539,USA

Telephone  +1-510-739-3777

Fax   +1-510-608-4555

Web site http://usa.asus.com

Technical Support

Support fax +1-812-284-0883

General support +1-812-282-2787

Online support https://support.asus.com/techserv/techserv.aspx

ASUS COMPUTER GmbH (Germany and Austria)

Address Harkort Str. 21-23, D-40880 Ratingen, Germany

Fax   +49-2102-959931

Web site http://www.asus.com/de

Online contact http://eu-rma.asus.com/sales

Technical Support

Telephone  +49-2102-5789555

SupportFax  +49-2102-959911

Online support http://support.asus.com/techserv/techserv.aspx

Manufacturer ASUSTeK Computer Inc.

Tel: +886-2-2894-3447

Address: No. 150, LI-TE RD., PEITOU, TAIPEI 112,

TAIWAN R.O.C

Authorised

representative in

Europe

ASUSTeK Computer GmbH

Address: HARKORT STR. 21-23, 40880 RATINGEN,

GERMANY

EC Declaration of Conformity

We, the undersigned,

Manufacturer: ASUSTeK COMPUTER INC.

Address: 4F, No. 150, LI-TE Rd., PEITOU, TAIPEI 112, TAIWAN

Authorized representative in Europe: ASUS COMPUTER GmbH

Address, City: HARKORT STR. 21-23, 40880 RATINGEN

Country: GERMANY

declare the following apparatus:

Product name : VivoMini

Model name : UN62,UN42

conform with the essential requirements of the following directives:

2004/108/EC-EMC Directive

EN 55022:2010+AC:2011

EN 61000-3-2:2006+A2:2009

EN 55013:2001+A1:2003+A2:2006

EN 55024:2010

EN 61000-3-3:2008

EN 55020:2007+A11:2011

1999/5/EC-R&TTE Directive

EN 300 328 V1.8.1(2012-06)

EN 300 440-1 V1.6.1(2010-08)

EN 300 440-2 V1.4.1(2010-08)

EN 301 511 V9.0.2(2003-03)

EN 301 908-1 V5.2.1(2011-05)

EN 301 908-2 V5.2.1(2011-07)

EN 301 893 V1.7.1(2012-06)

EN 302 544-2 V1.1.1(2009-01)

EN 302 623 V1.1.1(2009-01)

EN 50360:2001

EN 62479:2010

EN 50385:2002

EN 62311:2008

EN 301 489-1 V1.9.2(2011-09)

EN 301 489-3 V1.4.1(2002-08)

EN 301 489-4 V1.4.1(2009-05)

EN 301 489-7 V1.3.1(2005-11)

EN 301 489-9 V1.4.1(2007-11)

EN 301 489-17 V2.2.1(2012-09)

EN 301 489-24 V1.5.1(2010-09)

EN 302 326-2 V1.2.2(2007-06)

EN 302 326-3 V1.3.1(2007-09)

EN 301 357-2 V1.4.1(2008-11)

EN 302 291-1 V1.1.1(2005-07)

EN 302 291-2 V1.1.1(2005-07)

2006/95/EC-LVD Directive

EN 60950-1 / A12:2011 EN 60065:2002 / A12:2011

2009/125/EC-ErP Directive

Regulation (EC) No. 1275/2008

Regulation (EC) No. 642/2009

Regulation (EC) No. 278/2009

Regulation (EC) No. 617/2013

2011/65/EU-RoHS Directive

Ver. 140331

CE marking

Original Declaration Date: 06/10/2014

Corrected Declaration Date: 10/10/2014

Year to begin affixing CE marking: 2014

Position : CEO

Name :

Jerry Shen

Signature :

__________

(EC conformity marking)

DECLARATION OF CONFORMITY

Per FCC Part 2 Section 2. 1077(a)

Responsible Party Name:

Asus Computer International

Address: 800 Corporate Way, Fremont

, CA 94539.

Phone/Fax No: (510)739-3777/(510)608-4555

hereby declares that the product

Product Name : VivoMini

Model Number : UN62,UN42

Conforms to the following specifications:

FCC Part 15, Subpart B, Unintentional Radiators

Supplementary Information:

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Representative Person’s Name : Steve Chang / President

Signature :

Date : Oct. 06, 2014

Ver. 140331

Table of Contents

ASUS UN42-M088Y User Manual

Related Manuals