ASUS USB-N14 User Manual

Displayed below is the user manual for USB-N14 by ASUS which is a product in the Network Cards category. This manual has pages.

Related Manuals

ASUS ASUS Rampage IV GENE Manual

ASUS ASUS X99-DELUXE II Manual

ASUS ASUS MCI-10G/X550-2T Manual

ASUS UX435EAL-KC096T Manual

ASUS PN62S-B3519ZD Manual

ASUS VE228H Manual

ASUS RS700DA-E6/PS4 Manual

ASUS PCE-N15 Manual

User Manual

USB-N14

Dual-band Wireless-AC600

USB Adapter

No part of this manual, including the products and software described

in it, may be reproduced, transmitted, transcribed, stored in a retrieval

system, or translated into any language in any form or by any means, except

documentation kept by the purchaser for backup purposes, without the

express written permission of ASUSTeK Computer Inc. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is

repaired, modiﬁed or altered, unless such repair, modiﬁcation of alteration

is authorized in writing by ASUS; or (2) the serial number of the product is

defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY

KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE

IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS,

OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR

LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION

OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN

THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE

FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE

AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A

COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY

FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL,

INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not

be registered trademarks or copyrights of their respective companies, and

are used only for identiﬁcation or explanation and to the owners’ beneﬁt,

without intent to infringe.

E10123

First Edition

January 2015

Table of contents

1. Introduction .........................................................................4

Package contents ........................................................................................... 4

System requirements ....................................................................................4

Status indicator ............................................................................................... 4

2. Installing the USB-N14 driver .............................................5

3. Connecting to a wireless network ......................................7

Connecting to a wireless network using WPS .....................................8

4. Troubleshooting ..................................................................9

5. Glossary..............................................................................10

Notices .....................................................................................20

ASUS Contact Information ........................................................................24

1. Introduction

System requirements

Before using the USB-N14 adapter, check if your system meets the following

requirements:

If any of the above items is damaged or missing, contact your retailer

immediately.

LED Status Description

Link On USB-N14 has connected to a wireless network successfully.

O USB-N14 is not connected.

Using Wi-Fi Protected Setup (for Windows® OS only)

To enable Wi-Fi Protected Setup (WPS), press the WPS button on the USB-N14.

Package contents

• Windows® XP / Vista / 7 / 8 / Mac OSX / Linux

• 512MB system memory or larger

• USB2.0port

• Opticaldiskdrive

Status indicator

Operating and storage environment

1. Operating temperature: ambient temperature between 0˚C ~ 40˚C

2. Storage temperature: ambient temperature between -10˚C ~ 70˚C

3. Humidity: 5% ~ 90% (non-condensing)

ASUS USB-N14 adapter x1

Quick Start Guide x1

Support CD x1

Warranty card x1

USB cable x1

To install the driver for your ASUS USB-N14:

1. Place the bundled Support CD in the optical drive. An Autorun screen

appears if the Autorun function is enabled on your computer.

If the Autorun function is not enabled on your computer, double-click

SETUP.EXE from the root directory to run the Support CD.

2. Installing the USB-N14 driver

2. An InstallShield Wizard screen

appears. Click Next to continue.

Install the driver from the bundled Support CD before inserting the

USB-N14 into your computer.

3. Click Install to install driver to

default destination folder.

4. Click Finish to complete

installation.

A message will appear in the

Windows® notication area and the

LED indicator on USB-N14 turns

solid blue indicating that device

drivers have successfully been

installed.

5. Connect the USB-N14 to the USB

port on your computer using the

bundled USB cable.

Windows will automatically install

the driver for the device.

To connect the USB-N14 Wireless adapter to a station or Access Point:

2. Select an Access Point (AP) from

the list and click Connect.

1. Click the network connection icon

in the Windows® notication area

to show the available wireless

networks list.

3. Connecting to a wireless network

Connecting to a wireless network using WPS

The ASUS USB-N14 supports Wi-Fi Protected Setup (WPS) for Windows®

operating systems for securing wireless connections.

To connect the USB-N14 Wireless adapter to a WPS-enabled AP using the

WPS button:

Ensure that the AP you are trying to connect to supports the WPS

feature.

1. Enable the WPS function of the wireless AP.

2. Press both the WPS buttons on the AP and USB-N14 until the USB-N14

connects to the wireless AP to establish a secure connection.

3. If Security is enabled on the AP

or station, provide the required

password or passkey. Click OK.

4. Troubleshooting

This chapter provides solutions to problems which you may encounter when

installing or using ASUS USB-N14. Contact a qualied service technician

for assistance if the problem still persists after you have performed the

troubleshooting solutions.

How do I verify that my WLAN adapter is installed properly?

1. Right-click My Computer from the Start menu, then select Properties.

2. Select the Hardware tab, then click Device Manager.

3. Double-click Network adapters.

4. Double-click ASUS USB-N14 USB Wireless Adapter. An ASUS

USB-N14 USB Wireless Adapter window appears.

5. Check Device status to see if the WLAN adapter is working properly.

My WLAN adapter cannot connect to any Access Point.

• CheckifNetwork Type is set to Infrastructure mode.

• CheckiftheSSID of your WLAN adapter is the same as that of the

Access Point you want to connect to.

• CheckiftheEncryption settings of your WLAN adapter are the same as

the Access Point you want to connect to.

My WLAN adapter cannot connect to a station or WLAN

adapter.

• CheckifNetwork Type is set to Ad Hoc mode.

• CheckiftheSSID of your WLAN adapter is the same as that of the

station or the WLAN adapter you want to connect to.

• CheckiftheChannel of your WLAN adapter is the same as that of the

station or the WLAN adapter you want to connect to.

• CheckiftheEncryption settings of your WLAN adapter are the same as

those of the station or the WLAN adapter you want to connect to.

The connection quality is bad and the signal strength is weak.

• KeepyourWLANadapterawayfrommicrowaveovensandlargemetal

objects to avoid radio interference.

• MoveyourWLANadapterclosertotheaccesspoint,station,orWLAN

adapter you want to connect to.

5. Glossary

Access Point (AP)

A networking device that seamlessly connects wired and wireless networks.

Access Points combined with a distributed system support the creation of

multiple radio cells that enable roaming throughout a facility.

Ad Hoc

A wireless network composed solely of stations within mutual communication

range of each other (no Access Point).

Basic Rate Set

This option allows you to specify the data transmission rate.

Basic Service Area (BSS)

A set of stations controlled by a single coordination function.

Broadband

A type of data transmission in which a single medium (such as cable) carries

several data at once.

Channel

An instance of medium use for the purpose of passing protocol data units that

may be used simultaneously, in the same volume of space, with other instances

of medium use (on other channels) by other instances of the same physical

layer, with an acceptably low frame error ratio due to mutual interference.

Client

A client is the desktop or mobile PC that is connected to your network.

COFDM (for 802.11a or 802.11g)

Signal power alone is not enough to maintain 802.11b-like distances in an

802.11a/g environment. To compensate, a new physical-layer encoding

technology was designed that departs from the traditional direct-sequence

technology being deployed today. This technology is called COFDM (coded

OFDM). COFDM was developed specically for indoor wireless use and oers

performance much superior to that of spread-spectrum solutions. COFDM

works by breaking one high-speed data carrier into several lowerspeed

subcarriers, which are then transmitted in parallel. Each high-speed carrier is

20MHzwideandisbrokenupinto52subchannels,eachapproximately300KHz

wide. COFDM uses 48 of these subchannels for data, while the remaining four

are used for error correction. COFDM delivers higher data rates and a high

degree of multipath reection recovery, thanks to its encoding scheme and

error correction.

EachsubchannelintheCOFDMimplementationisabout300KHzwide.At

thelowendofthespeedgradient,BPSK(binaryphaseshiftkeying)isused

toencode125Kbpsofdataperchannel,resultingina6,000Kbps,or6Mbps,

data rate. Using quadrature phase shift keying, you can double the amount of

dataencodedto250Kbpsperchannel,yieldinga12Mbpsdatarate.Andby

using16-levelquadratureamplitudemodulationencoding4bitsperhertz,

you can achieve a data rate of 24Mbps. The 802.11a/g standard species

that all 802.11a/g-compliant products must support these basic data rates.

The standard also lets the vendor extend the modulation scheme beyond

24Mbps. Remember, the more bits per cycle (hertz) that are encoded, the more

susceptible the signal will be to interference and fading, and ultimately, the

shorter the range, unless power output is increased.

Default Key

This option allows you to select the default WEP key. This option allows you to

use WEP keys without having to remember or write them down. The WEP keys

generated using the Pass Phrase is compatible with other WLAN products. The

Pass Phrase option is not as secure as manual assignment.

Device Name

Also known as DHCP client ID or network name. Sometimes provided by an ISP

when using DHCP to assign addresses.

DHCP (Dynamic Host Conguration Protocol)

This protocol allows a computer (or many computers on your network) to be

automatically assigned a single IP address from a DHCP server.

DNS Server Address (Domain Name System)

DNS allows Internet host computers to have a domain name and one or

more IP addresses. A DNS server keeps a database of host computers and

their respective domain names and IP addresses, so that when a user enters

a domain name into the Internet browser, the user is sent to the proper IP

address. The DNS server address used by the computers on your home network

is the location of the DNS server your ISP has assigned.

DSL Modem (Digital Subscriber Line)

A DSL modem uses your existing phone lines to transmit data at high speeds.

Direct-Sequence Spread Spectrum (for 802.11b)

Spread spectrum (broadband) uses a narrowband signal to spread the

transmission over a segment of the radio frequency band or spectrum. Direct-

sequence is a spread spectrum technique where the transmitted signal is

spread over a particular frequency range.

Direct-sequence systems communicate by continuously transmitting a

redundant pattern of bits called a chipping sequence. Each bit of transmitted

data is mapped into chips and rearranged into a pseudorandom spreading

code to form the chipping sequence. The chipping sequence is combined with

a transmitted data stream to produce the output signal.

Wireless mobile clients receiving a direct-sequence transmission use the

spreading code to map the chips within the chipping sequence back into bits

to recreate the original data transmitted by the wireless device. Intercepting

and decoding a direct-sequence transmission requires a predened algorithm

to associate the spreading code used by the transmitting wireless device to the

receiving wireless mobile client.

This algorithm is established by IEEE 802.11b specications. The bit redundancy

within the chipping sequence enables the receiving wireless mobile client to

recreate the original data pattern, even if bits in the chipping sequence are

corrupted by interference. The ratio of chips per bit is called the spreading ratio.

A high spreading ratio increases the resistance of the signal to interference. A

low spreading ratio increases the bandwidth available to the user. The wireless

device uses a constant chip rate of 11Mchips/s for all data rates, but uses

dierent modulation schemes to encode more bits per chip at the higher data

rates. The wireless device is capable of an 11 Mbps data transmission rate, but

the coverage area is less than a 1 or 2 Mbps wireless device since coverage area

decreases as bandwidth increases.

Encryption

This provides wireless data transmissions with a level of security. This option

allowsyoutospecifya64-bitora128-bitWEPkey.A64-bitencryptioncontains

10hexadecimaldigitsor5ASCIIcharacters.A128-bitencryptioncontains26

hexadecimal digits or 13 ASCII characters.

64-bitand40-bitWEPkeysusethesameencryptionmethodandcan

interoperate on wireless networks. This lower level of WEP encryption uses

a 40-bit (10 hexadecimal digits assigned by the user) secret key and a 24-bit

Initialization Vector assigned by the device. 104-bit and 128-bit WEP keys use

the same encryption method.

All wireless clients in a network must have identical WEP keys with the access

pointtoestablishconnection.KeeparecordoftheWEPencryptionkeys.

Extended Service Set (ESS)

A set of one or more interconnected basic service set (BSSs) and integrated

local area networks (LANs) can be congured as an Extended Service Set.

ESSID (Extended Service Set Identier)

You must have the same ESSID entered into the gateway and each of its

wireless clients. The ESSID is a unique identier for your wireless network.

Ethernet

The most widely used LAN access method, which is dened by the IEEE 802.3

standard. Ethernet is normally a shared media LAN meaning all devices on the

network segment share total bandwidth. Ethernet networks operate at 10Mbps

using CSMA/CD to run over 10-BaseT cables.

Firewall

A rewall determines which information passes in and out of a network. NAT

can create a natural rewall by hiding a local network’s IP addresses from the

Internet. A Firewall prevents anyone outside of your network from accessing

your computer and possibly damaging or viewing your les.

Gateway

A network point that manages all the data trac of your network, as well as to

the Internet and connects one network to another.

ICS

ICS is used to share one computer’s Internet connection with the rest of the

computers on your network. When this computer is connected to the Internet,

all the communications to and from the Internet on your network are sent

through this computer which is called the host computer. The rest of the

computers can send and receive e-mail messages and access the web as if it

were connected directly to the Internet.

IEEE

The Institute of Electrical and Electronics Engineers. The IEEE sets standards for

networking, including Ethernet LANs. IEEE standards ensure interoperability

between systems of the same type.

IEEE 802.11

IEEE 802.xx is a set of specications for LANs from the Institute of Electrical

and Electronic Engineers (IEEE). Most wired networks conform to 802.3, the

specication for CSMA/CD based Ethernet networks or 802.5, the specication

for token ring networks. 802.11 denes the standard for wireless LANs

encompassing three incompatible (non-interoperable) technologies: Frequency

Hopping Spread Spectrum (FHSS), Direct Sequence Spread Spectrum (DSSS),

and Infrared. 802.11 species a carrier sense media access control and physical

layer specications for 1 and 2 Mbps wireless LANs.

IEEE 802.11a (54Mbits/sec)

Compared with 802.11b: The 802.11b standard was designed to operate in

the 2.4GHz ISM (Industrial, Scientic and Medical) band using direct-sequence

spreadspectrum technology. The 802.11a standard, on the other hand, was

designed to operate in the more recently allocated 5-GHz UNII (Unlicensed

National Information Infrastructure) band. And unlike 802.11b, the 802.11a

standard departs from the traditional spread-spectrum technology, instead

using a frequency division multiplexing scheme that’s intended to be friendlier

to oce environments.

The 802.11a standard, which supports data rates of up to 54 Mbps, is the Fast

Ethernet analog to 802.11b, which supports data rates of up to 11 Mbps. Like

Ethernet and Fast Ethernet, 802.11b and 802.11a use an identical MAC (Media

Access Control). However, while Fast Ethernet uses the same physical-layer

encoding scheme as Ethernet (only faster), 802.11a uses an entirely dierent

encoding scheme, called OFDM (orthogonal frequency division multiplexing).

The 802.11b spectrum is plagued by saturation from wireless phones,

microwave ovens and other emerging wireless technologies, such as Bluetooth.

In contrast, 802.11a spectrum is relatively free of interference.

The 802.11a standard gains some of its performance from the higher

frequencies at which it operates. The laws of information theory tie frequency,

radiated power and distance together in an inverse relationship. Thus, moving

up to the 5GHz spectrum from 2.4GHz will lead to shorter distances, given the

same radiated power and encoding scheme.

Compared with 802.11g

802.11a is a standard for access points and radio NICs that is ahead of 802.11g

in the market by about six months. 802.11a operates in the 5GHz frequency

band with twelve separate non-overlapping channels. As a result, you can have

up to twelve access points set to dierent channels in the same area without

them interfering with each other. This makes access point channel assignment

much easier and signicantly increases the throughput the wireless LAN can

deliver within a given area. In addition, RF interference is much less likely

because of the less-crowded 5GHz band.

IEEE 802.11b (11Mbits/sec)

In 1997, the Institute of Electrical and Electronics Engineers (IEEE) adopted the

802.11 standard for wireless devices operating in the 2.4 GHz frequency band.

This standard includes provisions for three radio technologies: direct sequence

spread spectrum, frequency hopping spread spectrum, and infrared. Devices

that comply with the 802.11 standard operate at a data rate of either 1 or 2

Mbps.

In 1999, the IEEE created the 802.11b standard. 802.11b is essentially identical

to the 802.11 standard except 802.11b provides for data rates of up to 11Mbps

for direct sequence spread spectrum devices. Under 802.11b, direct sequence

devices can operate at 11Mbps, 5.5Mbps, 2Mbps, or 1Mbps. This provides

interoperability with existing 802.11 direct sequence devices that operate only

at 2Mbps.

Direct sequence spread spectrum devices spread a radio signal over a range

of frequencies. The IEEE 802.11b specication allocates the 2.4GHz frequency

band into 14 overlapping operating Channels. Each Channel corresponds to a

dierent set of frequencies.

IEEE 802.11g

802.11g is a new extension to 802.11b (used in majority of wireless LANs today)

that broadens 802.11b’s data rates to 54 Mbps within the 2.4 GHz band using

OFDM (orthogonal frequency division multiplexing) technology. 802.11g allows

backward compatibility with 802.11b devices but only at 11 Mbps or lower,

depending on the range and presence of obstructions.

Infrastructure

A wireless network centered about an access point. In this environment, the

access point not only provides communication with the wired network but also

mediates wireless network trac in the immediate neighborhood.

IP (Internet Protocol)

The TCP/IP standard protocol that denes the IP datagram as the unit of

information passed across an Internet and provides the basis for connectionless

packet delivery service. IP includes the ICMP control and error message

protocol as an integral part. It provides the functional equivalent of ISO OSI

Network Services.

IP Address

An IP address is a 32-bit number that identies each sender or receiver of

information that is sent across the Internet. An IP address has two parts:

the identier of a particular network on the Internet and an identier of the

particular device (which can be a server or a workstation) within that network.

ISM Bands (Industrial, Scientic, and Medicine Bands)

Radio frequency bands that the Federal Communications Commission (FCC)

authorized for wireless LANs. The ISM bands are located at 902MHz, 2.400GHz,

and 5.7GHz.

ISP (Internet Service Provider)

An organization that provides access to the Internet. Small ISPs provide service

via modem and ISDN while the larger ones also oer private line hookups (T1,

fractional T1, etc.).

LAN (Local Area Network)

A communications network that serves users within a dened geographical

area. The benets include the sharing of Internet access, les and equipment

like printers and storage devices. Special network cabling (10 Base-T) is often

used to connect the PCs together.

MAC Address (Media Access Control)

A MAC address is the hardware address of a device connected to a network.

NAT (Network Address Translation)

NAT masks a local network’s group of IP addresses from the external network,

allowing a local network of computers to share a single ISP account. This

process allows all of the computers on your home network to use one IP

address. This will enable access to the Internet from any computer on your

home network without having to purchase more IP addresses from your ISP.

NIC (Network Interface Card)

A network adapter inserted into a computer so that the computer can be

connected to a network. It is responsible for converting data from stored in the

computer to the form transmitted or received.

Packet

A basic message unit for communication across a network. A packet usually

includes routing information, data, and sometimes error detection information.

Pass Phrase

The Wireless Settings utility uses an algorithm to generate four WEP keys based

on the typed combination.

PCMCIA (Personal Computer Memory Card International

Association)

The Personal Computer Memory Card International Association (PCMCIA),

develops standards for PC cards, formerly known as PCMCIA cards. These

cards are available in three types, and are about the same length and width as

credit cards. However, the dierent width of the cards ranges in thickness from

3.3 mm (Type I) to 5.0 mm (Type II) to 10.5 mm (Type III). These cards can be

used for various functions, including memory storage, land line modems and

wireless modems.

PPP (Point-to-Point Protocol)

PPP is a protocol for communication between computers using a serial

interface, typically a personal computer connected by phone line to a server.

PPPoE (Point-to-Point Protocol over Ethernet)

Point-to-Point Protocol is a method of secure data transmission. PPP using

Ethernet to connect to an ISP.

Preamble

Allows you to set the preamble mode for a network to Long, Short, or Auto. The

default preamble mode is Long.

Radio Frequency (RF) Terms: GHz, MHz, Hz

The international unit for measuring frequency is Hertz (Hz), equivalent to the

older unit of cycles per second. One megahertz (MHz) is one million Hertz.

One gigahertz (GHz) is one billion Hertz. The standard US electrical power

frequencyis60Hz,theAMbroadcastradiofrequencybandis0.55-1.6MHz,the

FM broadcast radio frequency band is 88-108MHz, and wireless 802.11 LANs

operate at 2.4GHz.

SSID (Service Set Identier)

SSID is a group name shared by every member of a wireless network. Only

client PCs with the same SSID are allowed to establish a connection. Enabling

the Response to Broadcast SSID requests option allows the device to

broadcast its SSID in a wireless network. This allows other wireless devices

to scan and establish communication with the device. Unchecking this

option hides the SSID to prevent other wireless devices from recognizing and

connecting to the device.

Station

Any device containing IEEE 802.11 wireless medium access conformity.

Subnet Mask

A subnet mask is a set of four numbers congured like an IP address. It is used

to create IP address numbers used only within a particular network.

TCP (Transmission Control Protocol)

The standard transport level protocol that provides the full duplex, stream

service on which many application protocols depend. TCP allows a process

or one machine to send a stream of data to a process on another. Software

implementing TCP usually resides in the operating system and uses the IP to

transmit information across the network.

WAN (Wide Area Network)

A system of LANs, connected together. A network that connects computers

located in separate areas, (i.e., dierent buildings, cities, countries). The Internet

is a wide area network.

WECA (Wireless Ethernet Compatibility Alliance)

An industry group that certies cross-vender interoperability and compatibility

of IEEE 802.11b wireless networking prod WPA (Wi-Fi Protected Access)

WPA (Wi-Fi Protected Access)

Wi-Fi Protected Access (WPA) is an improved security system for 802.11. It is

partofthe802.11idraftsecuritystandard.WPAencompassesTKIP(Temporal

KeyIntegrityProtocol)alongwithMIC(MessageIntegrityCheck)andother

xes to WEP such as Weak IV (Initialization Vector) ltering and Random IV

generation.TKIPuses802.1xtodeployandchangetemporarykeysasopposed

to static WEP keys once used in the past. It is a signicant improvement

over WEP. WPA is part of a complete security solution. WPA also requires

authentication servers in enterprise security solutions.

Requirements

(1) A WPA compatible Access Point or Wireless router, (2) Operating system

updates that support WPA. In XP, an updated Windows Zero Cong service is

needed. Users can download the Windows XP WPA patch here:

http://microsoft.com/downloads/details.aspx?FamilyId=009D8425-CE2B-47A4-

ABEC-274845DC9E91&displaylang=en

Please note that this patch requires the installation Windows XP Service

Pack 1, which is available here: http://www.microsoft.com/WindowsXP/pro/

downloads/servicepacks/sp1/default.asp

For earlier Windows Operating systems, a WPA capable supplicant is required

such as Funk Software’s Odyssey Client.

WLAN (Wireless Local Area Network)

This is a group of computers and other devices connected wirelessly in a small

area. A wireless network is referred to as LAN or WLAN.

WARNING: Any changes or modications not expressly approved by

the party responsible for compliance could void the user’s authority to

operate the equipment.

Notices

Federal Communications Commission

This device complies with FCC Rules Part 15. Operation is subject to the

following two conditions:

• Thisdevicemaynotcauseharmfulinterference,and

• Thisdevicemustacceptanyinterferencereceived,includinginterference

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a class

B digital device pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment o and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorientorrelocatethereceivingantenna.

• Increasetheseparationbetweentheequipmentandreceiver.

• Connecttheequipmentintoanoutletonacircuitdierentfromthatto

which the receiver is connected.

• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

Prohibition of Co-location

This device and its antenna(s) must not be co-located or operating in

conjunction with any other antenna or transmitter.

Operate the device in 5150-5250MHz frequency band for indoor use only.

FCC Radiation Exposure Statement

This equipment complies with RFCC radiation exposure limits set forth for an

uncontrolled environment .

This equipment should be installed and operated with minimum 20cm

between the radiator and your body.

CE Mark Warning

This is a Class B product, in a domestic environment, this product may cause

radio interference, in which case the user may be required to take adequate

measures.

Operation Channels: Ch1~11 for N. America, Ch1~14 Japan, Ch1~ 13 Europe

(ETSI)

DGT Warning Statement

Article 12

Without permission, any company, rm or user shall not alter the frequency,

increase the power, or change the characteristics and functions of the original

design of the certied lower power frequency electric machinery.

Article 14

The application of low power frequency electric machineries shall not aect

the navigation safety nor interfere a legal communication, if an interference

is found, the service will be suspended until improvement is made and the

interference no longer exists.

低功率電波輻射性電機管理辦法

(1)「經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、

加大功率或變更原設計之特性及功能」以及 (2)「低功率射頻電機之使用不得影響飛航安全及

干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合

法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及

醫療用電波輻射性電機設備之干擾」。

This Class [B] digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

For product available in the USA/Canada market, only channel 1~11 can be operated.

Selection of other channels is not possible.

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for

an uncontrolled environment. This equipment should be installed and operated

with minimum distance 20cm between the radiator & your body.

Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

IC Warning Statement

Under Industry Canada regulations, this radio transmitter may only operate

using an antenna of a type and maximum (or lesser) gain approved for the

transmitter by Industry Canada. To reduce potential radio interference to other

users, the antenna type and its gain should be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more than that necessary for

successful communication.

Thisradiotransmitter(IC:3568A-USBAC51)hasbeenapprovedbyIndustry

Canada to operate with the antenna types listed below with the maximum

permissible gain and required antenna impedance for each antenna type

indicated. Antenna types not included in this list, having a gain greater than

the maximum gain indicated for that type, are strictly prohibited for use with

this device.

Canada, avis d’Industry Canada (IC)

Cet appareil numérique de classe B est conforme aux normes canadiennes

ICES-003 et RSS-210.

Son fonctionnement est soumis aux deux conditions suivantes : (1) cet

appareil ne doit pas causer d’interférence et (2) cet appareil doit accepter

toute interférence, notamment les interférences qui peuvent aecter son

fonctionnement.

Informations concernant l’exposition aux fréquences radio (RF)

La puissance de sortie émise par l’appareil de sans l Dell est inférieure à

la limite d’exposition aux fréquences radio d’Industry Canada (IC). Utilisez

l’appareil de sans l Dell de façon à minimiser les contacts humains lors du

fonctionnement normal.

Ce périphérique a été évalué et démontré conforme aux limites SAR (Specic

Absorption Rate – Taux d’absorption spécique) d’IC lorsqu’il est installé

dans des produits hôtes particuliers qui fonctionnent dans des conditions

d’exposition à des appareils portables (les antennes se situent à moins de 20

centimètres du corps d’une personne). Ce périphérique est homologué pour

l’utilisation au Canada. Pour consulter l’entrée correspondant à l’appareil dans

la liste d’équipement radio (REL - Radio Equipment List) d’Industry Canada

rendez-vous sur:

http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng

Pour des informations supplémentaires concernant l’exposition aux RF au

Canada rendezvous sur : http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.

html

ASUS Recycling/Takeback Services

ASUS recycling and takeback programs come from our commitment to the

highest standards for protecting our environment. We believe in providing

solutions for you to be able to responsibly recycle our products, batteries, other

components as well as the packaging materials. Please go to http://csr.asus.

com/english/Takeback.htm for the detailed recycling information in dierent

regions.

REACH

Complying with the REACH (Registration, Evaluation, Authorisation, and

Restriction of Chemicals) regulatory framework, we published the chemical

substances in our products at ASUS REACH website at http://csr.asus.com/

english/REACH.htm.

ASUS Contact Information

ASUSTeK COMPUTER INC. (Asia Pacic)

Address 15 Li-Te Road, Peitou, Taipei, Taiwan 11259

Website www.asus.com.tw

Technical Support

Telephone +886228943447

Support Fax +886228907698

Online support support.asus.com

ASUS COMPUTER INTERNATIONAL (America)

Address 800 Corporate Way, Fremont, CA 94539, USA

Telephone +15029550883

Fax +15029338713

Website usa.asus.com

Online support support.asus.com

ASUS COMPUTER GmbH (Germany and Austria)

Address Harkort Str. 21-23, D-40880 Ratingen,

Germany

Fax +492102959911

Website www.asus.de

Online contact www.asus.de/sales

Technical Support

Telephone (Component) +491805010923*

Telephone (System/Notebook/Eee/LCD) +491805010920*

Fax +492102959911

Online support support.asus.com

* EUR 0.14/minute from a German xed landline; EUR 0.42/minute from a mobile phone.

AEEE Yönetmeliğine Uygundur.

Manufacturer ASUSTeK Computer Inc.

Tel:+886-2-2894-3447

Address: 4F., No. 150, LI-TE RD., PEITOU, TAIPEI 112, TAIWAN

Authorised

representative

in Europe

ASUS Computer GmbH

Address:HARKORTSTR.21-23,40880RATINGEN,GERMANY

Authorised

distributors in

Turkey

BOGAZICI BIL GISAYAR SAN. VE TIC. A.S.

Tel: +90 212 3311000

Address:AYAZAGAMAH.KEMERBURGAZCAD.NO.10AYAZAGA/

ISTANBUL

CIZGI Elektronik San. Tic. Ltd. Sti.

Tel:+902123567070

Address:CEMALSURURICD.HALIMMERICISMERKEZI

No:15/CD:5-634394MECIDIYEKOY/ISTANBUL

KOYUNCU ELEKTRONiK BiLGi iSLEM SiST. SAN. VE DIS TIC. A.S.

Tel:+902165288888

Address:EMEKMAH.ORDUCAD.NO:18,SARIGAZi,SANCAKTEPE

ISTANBUL