Table of Contents
- Notices
- Safety Information
- Care & Cleaning
- Takeback Services
- 1.1 Welcome!
- 1.2 Package Contents
- 1.3 Assembling the Monitor Base
- 1.4 Connect Cables
- 1.5 Monitor Introduction
- 2.1 Detaching the Base (for VESA Wall Mount)
- 2.2 Adjusting the Monitor
- 3.1 OSD (On-Screen Display) Menu
- 3.2 Specifications
- 3.3 Troubleshooting (FAQ)
- 3.4 Supported Timing List
- 3.5 Product Dimensions
ASUS VP279QGL User Manual
Displayed below is the user manual for VP279QGL by ASUS which is a product in the Computer Monitors category. This manual has pages.
Related Manuals
VP279 Series
LCD Monitor
User Guide
ii
Copyright © 2018 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless
such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the
owners’ benet, without intent to infringe.
First Edition
November 2018
iii
Table of Contents
Notices ......................................................................................................... iv
Safety Information ...................................................................................... vi
Care & Cleaning ........................................................................................ viii
Takeback Services ...................................................................................... ix
1.1 Welcome! ...................................................................................... 1-1
1.2 Package Contents ........................................................................ 1-1
1.3 Assembling the Monitor Base ..................................................... 1-2
1.4 Connect Cables ............................................................................ 1-4
1.4.1 Rear of the LCD Monitor ................................................. 1-4
1.5 Monitor Introduction .................................................................... 1-5
1.5.1 Using the Control Buttons ............................................... 1-5
1.5.2 QuickFit Function ............................................................ 1-7
2.1 Detaching the Base (for VESA Wall Mount) ............................... 1-8
2.2 Adjusting the Monitor .................................................................. 2-2
3.1 OSD (On-Screen Display) Menu .................................................. 3-1
3.1.1 HowtoRecongure ........................................................ 3-1
3.1.2 OSD Function Introduction .............................................. 3-2
3.2 Specications ............................................................................. 3-11
3.3 Troubleshooting (FAQ) .............................................................. 3-12
3.4 Supported Timing List ............................................................... 3-13
3.5 Product Dimensions .................................................................. 3-14
iv
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This product implements power management functionality. In case of no
signal input after 10 seconds, the product automatically goes to sleep/
standby mode.
As an Energy Star® Partner, our company has determined
that this product meets the Energy Star® guidelines for
energyefciency.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
AEEE Yönetmeliine Uygundur
v
TCO Information
Congratulations!
ThisproductisTCOCertied—forSustainableIT
TCOCertiedisaninternationalthirdparty
sustainabilitycerticationforITproducts.TCOCertied
ensures that the manufacture, use and recycling of IT
productsreectenvironmental,socialandeconomic
responsibility.EveryTCOCertiedproductmodelis
veriedbyanaccreditedindependenttestlaboratory.
ThisproducthasbeenveriedtomeetallthecriteriainTCOCertied,including:
• Corporate Social Responsibility: Socially responsible production -
working conditions and labor law in manufacturing country.
• Energy Efficiency: Energy efficiency of product and power supply.
Energy Star compliant, where applicable.
• Environmental Management System: Manufacturer must be certified
according to either ISO 14001 or EMAS.
• Minimization of Hazardous Substances: Limits on cadmium,
mercury, lead & hexavalent chromium including requirements for
mercury-free products, halogenated substances and hazardous flame
retardants.
• Design for Recycling: Coding of plastics for easy recycling. Limit on
the number of different plastics used.
• Product Lifetime, Product Take Back: Minimum one-year product
warranty. Minimum three-year availability of spare parts. Product
takeback.
• Packaging: Limits on hazardous substances in product packaging.
Packaging prepared for recycling.
• Ergonomic, User-centered design: Visual ergonomics in products
with a display. Adjustability for user comfort (displays, headsets)
Acoustic performance protection against sound spikes (headsets) and
fan noise (projectors, computers) Ergonomically designed keyboard
(notebooks).
• Electrical Safety, minimal electro-magnetic Emissions Third
Party Testing: All certified product models have been tested in an
independent, accredited laboratory.
A detailed criteria set is available for download at www.tcodevelopment.com,
whereyoucanalsondasearchabledatabaseofallTCOCertiedITproducts.
vi
TCODevelopment,theorganizationbehindTCOCertied,hasbeen
aninternationaldriverintheeldofSustainableITfor20years.Criteria
inTCOCertiedaredevelopedincollaborationwithscientists,experts,
users and manufacturers. Organizations around the world rely on TCO
CertiedasatooltohelpthemreachtheirsustainableITgoals.Weare
ownedbyTCO,anon-protorganizationrepresentingofceworkers.
TCO Development is headquartered in Stockholm, Sweden, with regional
presence in North America and Asia.
For more information, please visit www.tcodevelopment.com.
Safety Information
• Before setting up the monitor, carefully read all the documentation that
came with the package.
• To prevent fire or shock hazard, never expose the monitor to rain or
moisture.
• Never try to open the monitor cabinet. The dangerous high voltages
inside the monitor may result in serious physical injury.
• If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your retailer.
• Before using the product, make sure all cables are correctly connected
and the power cables are not damaged. If you detect any damage,
contact your dealer immediately.
• Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or
over a radiator or heat source unless proper ventilation is provided.
• The monitor should be operated only from the type of power source
indicated on the label. If you are not sure of the type of power supply to
your home, consult your dealer or local power company.
• Use the appropriate power plug which complies with your local power
standard.
• Do not overload power strips and extension cords. Overloading can
result in fire or electric shock.
• Avoid dust, humidity, and temperature extremes. Do not place the
monitor in any area where it may become wet. Place the monitor on a
stable surface.
• Unplug the unit during a lightning storm or if it will not be used for a
long period of time. This will protect the monitor from damage due to
power surges.
• Never push objects or spill liquid of any kind into the slots on the
monitor cabinet.
vii
• To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked
between 100-240V AC.
• The socket-outlet shall be installed near the equipment and shall be
easily accessible.
• If you encounter technical problems with the monitor, contact a
qualified service technician or your retailer.
• This product may contain chemicals known to the State of California
tocausecancer,andbirthdefectsorotherreproductiveharm.Wash
hands after handling.
viii
Care & Cleaning
• Before you lift or reposition your monitor, it is better to disconnect the
cables and power cord. Follow the correct lifting techniques when
positioningthemonitor.Whenliftingorcarryingthemonitor,graspthe
edges of the monitor. Do not lift the display by the stand or the cord.
• Cleaning. Turn your monitor off and unplug the power cord. Clean the
monitor surface with a lint-free, non-abrasive cloth. Stubborn stains
may be removed with a cloth dampened with mild cleaner.
• Avoid using a cleaner containing alcohol or acetone. Use a cleaner
intended for use with the LCD. Never spray cleaner directly on the
screen, as it may drip inside the monitor and cause an electric shock.
The following symptoms are normal with the monitor:
• The screen may flicker during the initial use due to the nature of the
fluorescent light. Turn off the Power Switch and turn it on again to
make sure that the flicker disappears.
• You may find slightly uneven brightness on the screen depending on
the desktop pattern you use.
• Whenthesameimageisdisplayedforhours,anafterimageofthe
previous screen may remain after switching the image. The screen will
recover slowly or you can turn off the Power Switch for hours.
• Whenthescreenbecomesblackorflashes,orcannotworkanymore,
contact your dealer or service center to fix it. Do not repair the screen
by yourself!
Conventions used in this guide
WARNING:Informationtopreventinjurytoyourselfwhentrying
to complete a task.
CAUTION: Information to prevent damage to the components
when trying to complete a task.
IMPORTANT: Information that you MUST follow to complete a
task.
NOTE: Tips and additional information to aid in completing a task.
ix
Wheretondmoreinformation
Refer to the following sources for additional information and for product
and software updates.
1. ASUS websites
The ASUS websites worldwide provide updated information on ASUS
hardware and software products. Refer to http://www.asus.com
2. Optional documentation
Your product package may include optional documentation that may
have been added by your dealer. These documents are not part of
the standard package.
Takeback Services
ASUS recycling and takeback programs come from our commitment to the
higheststandardsforprotectingourenvironment.Webelieveinproviding
solutions for our customers to be able to responsibly recycle our products,
batteries and other components as well as the packaging materials.
Please go to http://csr.asus.com/english/Takeback.htm for detail recycling
information in different region.
1-1 Chapter 1: Product Introduction
1.1 Welcome!
Thank you for purchasing the ASUS® LCD monitor!
The latest widescreen LCD monitor from ASUS provides a crisper,
broader, and brighter display, plus a host of features that enhance your
viewing experience.
Withthesefeatures,youcanenjoytheconvenienceanddelightfulvisual
experience that the monitor brings to you!
1.2 Package Contents
Check your package for the following items:
LCD monitor
Power cord
Monitor base
QuickStartGuide
Warrantycard
VGAcable(optional)
HDMI cable (optional)
DP cable (optional)
Audio cable (optional)
•If any of the above items is damaged or missing, contact your retailer
immediately.
CAUTION
1-2
ASUS LCD Monitor VP279 Series
1.3 Assembling the Monitor Base
VP279QG
1. Have the front of the monitor face down on a table.
2. Attach the base to the arm.
3. Turn the screw clockwise to secure the base.
•Werecommendthatyoucoverthetablesurfacewithsoftclothtoprevent
damage to the monitor.
1-3 Chapter 1: Product Introduction
VP279QGL
1. Have the front of the monitor face down on a table.
2. Rotatethearm90˚counter-clockwise.
3. Attach the base to the arm.
4. Turn the screw clockwise to secure the base.
•Werecommendthatyoucoverthetablesurfacewithsoftclothtoprevent
damage to the monitor.
1-4
ASUS LCD Monitor VP279 Series
1.4 Connect Cables
1.4.1 Rear of the LCD Monitor
100 mm
100 mm
HDMI VGA
VGA
HDMI
1
7 8
22 3 4
5 6
100 mm
100 mm
HDMI VGA
VGA
HDMI
1
7 8
22 3 4
5 6
VP279QG VP279QGL
1. Control buttons
2. Speakers
3. AC-IN port
4. Kensington Lock
5. DisplayPort
6. HDMI port
7. VGAport
8. Audio-IN port
1-5 Chapter 1: Product Introduction
1.5 Monitor Introduction
1.5.1 Using the Control Buttons
Use the control buttons on the bottom of the monitor to adjust the image
settings. Press key 1-6 to activate the key list page.
Input Select
Menu
Close
QuickFit
Blue Light Filter
Brightness
21 34 5 6 7
1 2 345 6
1. Shortcut Key2:
• This is a Shortcut key. The default setting is Blue Light Filter
with Level 0.
2. Shortcut Key1:
• This is a Shortcut key. The default setting is Brightness.
3. QuickFit Button:
• This is a hotkey to activate the QuickFit function designed for
alignment.
• The QuickFit function contains several options of common grid
pattern, paper size, and photo size. See page 1-7 for details.
1-6
ASUS LCD Monitor VP279 Series
4.
Input Button:
• Switch the input source.
5. Close Button:
• Exit the OSD menu.
6. Menu Button:
• Enter the OSD menu.
7. Power Button/Power Indicator:
• Press this button to turn the monitor on/off.
• The color definition of the power indicator is as the table below.
Status Description
White ON
Amber Standby mode
OFF OFF
1-7 Chapter 1: Product Introduction
1.5.2 QuickFit Function
TheQuickFitfunctioncontainsthreepatterns:(1)Grid(2)Papersize
(3) Photo size.
1. Gridpattern:Facilitatesdesignersanduserstoorganizecontentand
layout on one page and achieve a consistent look and feel.
Alignment Grid 1 Alignment Grid 2
2. Paper size: Provides users to view their documents in real size on the
screen.
A4 B5
A4 B5
Letter
Letter
EXIT
3. Photo size: Provides photographers and other users to accurately
view and edit their photos in real size on the screen.
8x10 5x7 3x5 2x2
4x6
1-8
ASUS LCD Monitor VP279 Series
2.1 Detaching the Base (for VESA Wall
Mount)
VP279QG
To detach the base, perform the following:
1. Disconnect power and signal cables. Carefully put the front of the
monitor face down on a clean table.
2. Turn the screw counter-clockwise to loosen the screw located at the
bottom of the base.
3. Remove the base from the stand assembly.
4. Remove the stand cover. Then loosen the 4 screws to remove the
arm.
5. Align and install the wall mount bracket on the rear of the monitor.
Screw holes for VESA wall mount
(100 x 100 mm)
• Werecommendthatyoucoverthetablesurfacewithsoftclothtoprevent
damage to the monitor.
• Hold the base while removing the screw.
• The VESA wall mount kit ( 100 x 100 mm) is purchased separately.
• UseonlytheULListedWallMountBracketwithminimumweight/load
22.7kg (Screw size: M4 x 10 mm).
2-1 Chapter 2: Setup
VP279QGL
To detach the base, perform the following:
1. Disconnect power and signal cables. Carefully put the front of the
monitor face down on a clean table.
2. Loosen the 4 screws securing the arm.
3. Remove the stand assembly (arm and monitor base).
4. Align and install the wall mount bracket on the rear of the monitor.
Screw holes for VESA wall mount
(100 x 100 mm)
•Werecommendthatyoucoverthetablesurfacewithsoftclothtoprevent
damage to the monitor.
• The VESA wall mount kit ( 100 x 100 mm) is purchased separately.
• UseonlytheULListedWallMountBracketwithminimumweight/load
22.7kg (Screw size: M4 x 10 mm).
2-2
ASUS LCD Monitor VP279 Series
2.2 Adjusting the Monitor
• For optimal viewing, we recommend that you look at the full face of the
monitor, then adjust the monitor to the angle that is most comfortable
for you.
• Hold the stand to prevent the monitor from falling while changing its
angle.
VP279QG
You can adjust the monitor’s angle from -5° to 22°.
-5˚ to +22˚
VP279QGL
The recommended angle and height adjustments are the following:
-5˚ to +30˚
90°90°
• Tilt angle: -5° to 30°• Swiveling angle: +90° to -90°
2-3 Chapter 2: Setup
130 mm
• Adjustable height: 130mm
To change the screen orientation, perform the following:
1. Raise the screen to the highest position (130mm). Then slightly tilt
the monitor backwards.
2. Rotate the monitor (90° clockwise or counter-clockwise) to portrait
orientation.
90°
90°
•It is normal that the monitor slightly shakes while you adjust the viewing
angle.
3-1
ASUS LCD Monitor VP279 Series
3.1 OSD (On-Screen Display) Menu
3.1.1 HowtoRecongure
Splendid
Scenery mode
Standard Mode
Theater Mode
Game Mode
Night View Mode
sRGB Mode
Reading Mode
Darkroom Mode
Standard Mode HDMI 1920 x 1080 @ 60Hz
ASUS VP279
1. Press the Menu button to activate the OSD menu.
2. Press the and buttons to toggle between options in the
Menu. As you move from one icon to another, the option name is
highlighted.
3. To select the highlighted item on the menu, press the button.
4. Press the and buttons to select the desired parameter.
5. Press the button to enter the slide bar and then use the and
buttons, according to the indicators on the menu, to make your
changes.
6. Select to return to previous menu or to accept and return to
previous menu.
3-2 Chapter3:GeneralInstruction
3.1.2 OSD Function Introduction
1. Splendid
This function contains eight sub-functions that you can select for
your preference. Each mode has the Reset selection, allowing you to
maintain your setting or return to the preset mode.
Splendid
Scenery mode
Standard Mode
Theater Mode
Game Mode
Night View Mode
sRGB Mode
Reading Mode
Darkroom Mode
Standard Mode HDMI 1920 x 1080 @ 60Hz
ASUS VP279
• Scenery mode: This is the best choice for scenery photo
displaying with SPLENDID™ Video Intelligence Technology.
• Standard Mode: This is the best choice for document editing
with SPLENDID™ Video Intelligence Technology.
• Theater Mode: This is the best choice for movie watching with
SPLENDID™ Video Intelligence Technology.
• Game Mode: This is the best choice for game playing with
SPLENDID™ Video Intelligence Technology.
• Night View Mode: This is the best choice for playing dark-scene
game or watching dark-scene movie with SPLENDID™ Video
Intelligence Technology.
• sRGB Mode: This is the best choice for viewing photos and
graphics from PCs.
• Reading Mode: This is the best choice for book reading with
SPLENDID™ Video Intelligence Technology.
• Darkroom Mode: This is the best choice for a weak ambient
light environment with SPLENDID™ Video Intelligence
Technology.
3-3
ASUS LCD Monitor VP279 Series
• In the Standard Mode, the Saturation, Skin Tone, Sharpness, and ASCR
functionsarenotuser-congurable.
• InthesRGB,theSaturation,ColorTemp.,SkinTone,Sharpness,
Brightness,Contrast,andASCRfunctionsarenotuser-congurable.
• In the Reading Mode, the Saturation, SkinTone, ASCR, Contrast, and Color
Temp.functionsarenotuser-congurable.
2. Blue Light Filter
Reduce the energy level of blue light emitted from LED backlight.
Blue Light Filter
Level 0
Level 1
Level 2
Level 3
Level 4
Standard Mode HDMI 1920 x 1080 @ 60Hz
ASUS VP279
• Level 0: No change.
• Level 1~4: The higher the level, the less blue light is scattered.
WhentheBlueLightFilterisactivated,thedefaultsettingsof
Standard Mode will be automatically imported. Between Level
1 to Level 3, the Brightness function is user-configurable. Level
4 is optimized setting. It is compliance with TUV Low Blue Light
Certification. The Brightness function is not user-configurable.
• Users should take some time away from the display if working for long
hours: It is advised to take short breaks (at least 5 mins) after around 1
hour of continuous working at the computer. Taking short and frequent
breaks is more effective than a single longer break.
• To minimize eye strain and dryness in your eyes, users should rest the eye
periodically by focusing on objects that are far away.
• Eye exercises can help to reduce eye strain. Repeat these exercises often.
If eye strain continues, please contact a physician.
Eye exercises: (1) Repeating look up and down (2) Slowly roll your eyes
(3) Move your eyes diagonal.
• High energy blue light may lead to eye strain and AMD (Age-Related
Macular Degeneration). Use Blue Light Filter to reduce 70% (max.) harmful
blue light to avoiding CVS (Computer Vision Syndrome).
3-4 Chapter3:GeneralInstruction
3. Color
Select the image color you like from this function.
Color
Brightness
Contrast
Saturation
Color Temp.
Skin Tone
Standard Mode HDMI 1920 x 1080 @ 60Hz
ASUS VP279
• Brightness: Adjust the brightness level. The adjusting range is
from 0 to 100.
• Contrast: Adjust the contrast level. The adjusting range is from
0 to 100.
• Saturation: Adjust the saturation level. The adjusting range is
from 0 to 100.
• Color Temp.: Select the desired color temperature. Available
options: Cool, Normal, Warm, and User Mode.
• IntheUserMode,colorsofR(Red),G(Green),andB(Blue)areuser-
congurable;theadjustingrangeisfrom0~100.
• Skin Tone: Select the desired skin color. Available options:
Reddish, Natural, and Yellowish.
3-5
ASUS LCD Monitor VP279 Series
4. Image
You can adjust the image Sharpness, Trace Free, Aspect Control,
VividPixel, ASCR, Adaptive-Sync/FreeSync, ELMB, Position, Focus,
and Auto Adjust from this main function.
Image
Sharpness
VividPixel
ASCR
Adaptive-Sync/FreeSync
ELMB
Standard Mode VGA 1920 x 1080 @ 60Hz
ASUS VP279
Trace Free
Aspect Control
Position
(Page 1/2)
Image
Standard Mode VGA 1920 x 1080 @ 60Hz
ASUS VP279
Auto Adjust
Focus
(Page 2/2)
• Sharpness: Adjust the picture sharpness. The adjusting range
is from 0 to 100.
• Trace Free: Speed up the response time by Over Drive
technology. The adjusting range is from lower 0 to faster 100.
3-6 Chapter3:GeneralInstruction
• Aspect Control: Adjust the aspect ratio to “Full”, “4:3”, or
“OverScan”.
• 4:3 is only available when the input source is in 4:3 format.
• OverScan is only available for HDMI input.
• VividPixel: ASUS Exclusive Technology that brings lifelike
visuals for crystal-clear and detail-oriented enjoyment. The
adjustingrangeisfrom0~100.
• ASCR: Select ON or OFF to enable or disable dynamic contrast
ratio function.
• Adaptive-Sync/FreeSync: Allows an Adaptive-Sync or
FreeSync supported graphics source (HDMI and DisplayPort) to
dynamically adjust display refresh rate based on typical content
frame rates for power efficient, virtually stutter free and low-
latency display update.
•If the Adaptive-Sync/FreeSync is enabled, the ELMB function is grayed out.
• ELMB: Decreases motion blur and minimize ghosting part when
on-screen objects are fast-moving. This function is available
when the refresh rate is 75Hz.
•If the Adaptive-Sync/FreeSync is enabled, the ELMB function is grayed out.
• Position: Adjust the horizontal position (H-Position) and the
vertical position (V-Position) of the image. The adjusting range is
from0to100(onlyavailableforVGAinput).
• Focus: Reduce the Horizontal-line noise and Vertical-line noise
of the image by adjusting (Phase) and (Clock) separately. The
adjustingrangeisfrom0to100(onlyavailableforVGAinput).
• Auto Adjust: Automatically perform Auto Adjust (only available
forVGAinput).
3-7
ASUS LCD Monitor VP279 Series
5. Input Select
Select the input source.
Input Select
VGA
HDMI
DisplayPort
Standard Mode HDMI 1920 x 1080 @ 60Hz
ASUS VP279
6. System Setup
Adjustthesystemconguration.
System Setup
Splendid Demo Mode
Volume
GamePlus
ECO Mode
OSD Setup
Language
Key Lock
Information
Standard Mode HDMI 1920 x 1080 @ 60Hz
ASUS VP279
(Page 1/2)
3-8 Chapter3:GeneralInstruction
System Setup
Power Indicator
Power Key Lock
All Reset
Standard Mode HDMI 1920 x 1080 @ 60Hz
ASUS VP279
(Page 2/2)
• Splendid Demo Mode: Activate the demo mode for the
Splendid function.
• Volume: Adjust the volume level.
• GamePlus:ConfiguretheGamePlusfunction.Seepage 3-10
for details.
• ECO Mode: Activate the ecology mode for power saving.
• OSD Setup: Adjust the OSD Timeout, DDC/CI, and
Transparency of the OSD screen.
• Language: Select the OSD language.
• Key Lock: Pressing the second button on the right for more than
five seconds to activate the key lock function.
• Information: Display the monitor information.
• Power Indicator: Turn the power LED indicator on/off.
• Power Key Lock: Disable/Enable the power key.
• All Reset: Select YES to revert all settings to the factory default
mode.
3-9
ASUS LCD Monitor VP279 Series
7. Shortcut
Assign the specific function to the two shortcut keys.
Shortcut
Shortcut 1
Shortcut 2
Blue Light Filter
Splendid
Brightness
Auto Adjust
Contrast
Color Temp.
Volume
Standard Mode HDMI 1920 x 1080 @ 60Hz
ASUS VP279
GamePlus
(Shortcut 1)
Shortcut
Shortcut 1
Shortcut 2
Blue Light Filter
Splendid
Brightness
Auto Adjust
Contrast
Color Temp.
Volume
GamePlus
Standard Mode HDMI 1920 x 1080 @ 60Hz
ASUS VP279
(Shortcut 2)
• Shortcut 1: Assign a function to the Shortcut Key1.
Available options: Blue Light Filter, Splendid, Brightness,
Auto Adjust, Contrast, Color Temp., Volume, and GamePlus.
The default setting is Brightness
.
• Shortcut 2: Assign a function to the Shortcut Key2.
Available options: Blue Light Filter, Splendid, Brightness,
Auto Adjust, Contrast, Color Temp., Volume, and GamePlus.
The default setting is Blue Light Filter.
3-10 Chapter3:GeneralInstruction
3.1.2.1 GamePlus Function
TheGamePlusFunctionprovidesatoolkitandcreatesabettergaming
environment for users when playing different types of games. The
Crosshair overlay with four different crosshair options lets you choose the
one that best suits the game you’re playing. The onscreen Timer can be
positioned on the left of the display to keep track of the elapsed gaming
time. The FPS (frames per second) counter lets you know how smooth the
game is running.
To activate GamePlus:
1. Press the Menu button to activate the OSD menu.
2. Press the or button to select Shortcut. Then press the
button to enter the Shortcut menu.
3. Press the or button to select Shortcut 1 or Shortcut 2.
4. Press the button to enter the Shortcut 1 or Shortcut 2 submenu.
5. Press the or button to select GamePlus. Then press the
buttontoconrmtheGamePlus submenu.
6. Press the or button to select Crosshair, Timer, FPS Counter
or Display Alignment. Then press the buttontoconrmthe
selection.
7. Press the button repeatedly to exit the OSD menu.
8. Press the assigned Shortcut Key1 or Shortcut Key2 to activate the
GamePlusmainmenu.
GamePlus Main Menu
Practice Mode
Crosshair Timer FPS Counter
FPS
GamePlus
Display Alignment
GamePlus - Crosshair GamePlus - Timer
GamePlus - Timer - Position GamePlus - FPS - Position
Position Position
FPS
3-11
ASUS LCD Monitor VP279 Series
3.2 Specications
Model VP279QG VP279QGL
Panel Size 27 inches diagonal
(Active Display Area: 597.9 (H) x 336.3 (V) mm)
Max. Resolution 1920 x 1080
Brightness (Typ.) 250 cd/m2
Contrast Ratio (Typ.) 1000:1
ViewingAngle(CR≤10) 178°(V);178°(H)
Display Colors 16.7M colors (6 bits + Advanced-FRC)
Response Time 5ms(GTG)
Terminals
Inputs: HDMIx1,DPx1,VGAx1
Audio output: Headphone
Audio speaker: Stereo2Wx2
Power consumption 29W(Max)inTestLinePatternwithaudio
24W(Max)inTestLinePatternwithoutaudio
Standby power
consumption <0.5WatAC110V~AC220V
Power off power
consumption <0.5WatAC110V~AC220V
Phys. Dimension (incl. base)
(HxWxD) 622.6 x 442.5 x 215 mm 523.8 x 622.6 x 226.4 mm
BoxDimension(HxWxD) 513 x 680 x 126±5 mm 465 x 722 x 189±5 mm
NetWeight(incl.stand) 4.8 ±1.0 kg 7.0 ±1.0 kg
GrossWeight(Esti.) 6.75 ±1.0 kg 9.15 ±1.0 kg
Voltage Rating 100~240Vat50/60Hz
Temperature Operatingtemperature:0~40˚C
Storagetemperature:-30~65˚C
Accessories
Powercord,QuickStartGuide,Warrantycard,HDMIcable
(optional),DPcable(optional),VGAcable(optional),audio
cable (optional)
Compliance and
Standards
CE, CB, FCC, CCC, CU, RCM, UL/cUL, UKrSEPRO, BSMI,
KC(EK)/ MSIP(KCC)/ E-Standby(E-Boy), PSE, VCCI, Energy
Star7.0,HDMI,Windows7&8WHQL,GEMS,TCO7.0,China
EnergyLabel,RoHS,WEEE,EuP(EnergySavingOnly)
*Specicationssubjecttochangewithoutnotice.
3-12 Chapter3:GeneralInstruction
3.3 Troubleshooting (FAQ)
Problem Possible Solution
Power LED is not ON • Press the button to check if the monitor is turned
on.
• Check if the adapter and power cord are properly
connected to the monitor and the power outlet.
• Check the Power Indicator function in the OSD
menu. Select “ON“ to turn on the power LED.
The power LED lights amber and
there is no screen image
• Check if the monitor and the computer are turned
on.
• Make sure the signal cable is properly connected the
monitor and the computer.
• Inspect the signal cable and make sure none of the
pins are bent.
• Connect the computer with another available monitor
to check if the computer is properly working.
Screen image is too light or dark • Adjust the Contrast and Brightness settings via
OSD.
Screen image bounces or a wave
pattern is present in the image
• Make sure the signal cable is properly connected to
the monitor and the computer.
• Move electrical devices that may cause electrical
interference.
Screen image has color defects
(white does not look white)
• Inspect the signal cable and make sure that none of
the pins are bent.
• Perform Reset via OSD.
• Select the appropriate color temperature (Color
Temp.) via OSD.
No sound or sound is low • Adjust the volume settings of your monitor or
computer.
• Make sure the computer sound card driver is
properly installed and activated.
3-13
ASUS LCD Monitor VP279 Series
3.4 Supported Timing List
VESA / IBM Modes Support Timing
Mode Resolution
(active dot)
Resolution
(total dot)
Horizontal
Frequency
(KHz)
Vertical
Frequency
(Hz)
Nominal Pixel
Color
(MHz)
DOS 720x400@70Hz 900x449 31.469 70.087 28.322
VGA
640x480@60Hz 800x525 31.469 59.940 25.175
640x480@72Hz 832x520 37.861 72.809 31.500
640x480@75Hz 840x500 37.500 75.000 31.500
SVGA
800x600@56Hz 1024x625 35.156 56.250 36.000
800x600@60Hz 1056x628 37.879 60.317 40.000
800x600@72Hz 1040x666 48.077 72.188 50.000
800x600@75Hz 1056x625 46.875 75.000 49.500
XGA
1024x768@60Hz 1344x806 48.363 60.004 65.000
1024x768@70Hz 1328x806 56.476 70.069 75.000
1024x768@75Hz 1312x800 60.023 75.029 78.750
VESA 1152x864@75Hz 1600x900 67.500 75.000 108.000
SXGA
1280x1024@60Hz 1688x1066 63.981 60.020 108.000
1280x1024@75Hz 1688x1066 79.976 75.025 135.000
1280x960@60Hz 1800x1000 60.000 60.000 108.000
WXGA
1280x800@60Hz 1680x831 49.702 59.810 83.500
1280x720@60Hz 1650x750 45.000 60.000 74.250
1280x768@60Hz 1664x798 47.776 59.870 79.500
1360x768@60Hz 1792x795 47.712 60.015 85.500
1366x768@60Hz 1792x798 47.712 59.790 85.500
WXGA+ 1440x900@60Hz 1904x934 55.935 59.887 106.500
UXGA 1600x1200@60Hz 2160x1250 75.000 60.000 162.000
WSXGA+ 1680x1050@60Hz 2240x1089 65.290 59.954 146.250
WUXGA 1920x1080@60Hz 2200x1125 67.500 60.000 148.500
1920x1080@75Hz 2080x1119 83.890 74.970 174.500
MAC 640x480@66.66Hz 864x525 35.000 66.660 30.240
SVGA 832x624@75Hz 1152x667 49.714 74.533 57.270
* Modes not listed in the table may not be supported. For optimal resolution, we recommend that
you choose a mode listed in the table above.
3-14 Chapter3:GeneralInstruction
3.5 Product Dimensions
VP279QG
3-15
ASUS LCD Monitor VP279 Series
VP279QGL