Notices
Chapter 1: Product Introduction
Chapter 2: Hardware Information
Chapter 3: Powering Up
- 3.1 Starting up for the first time
- 3.2 Powering off the computer
  - 3.2.1 Using the OS shut down function
  - 3.2.2 Using the dual function power switch
Chapter 4: BIOS Setup
Chapter 5: RAID Configuration
Chapter 6: Driver Installation
Appendix

ASUS Z11PA-U12 User Manual

Displayed below is the user manual for Z11PA-U12 by ASUS which is a product in the Motherboards category. This manual has pages.

Related Manuals

ASUS ASUS Rampage IV GENE Manual

ASUS ASUS X99-DELUXE II Manual

ASUS ASUS MCI-10G/X550-2T Manual

ASUS UX435EAL-KC096T Manual

ASUS PN62S-B3519ZD Manual

ASUS VE228H Manual

ASUS RS700DA-E6/PS4 Manual

ASUS PCE-N15 Manual

Z11PA-U12 Series

User Guide

E13361

First Edition

September 2017

No part of this manual, including the products and software described in it, may be reproduced, transmitted,

transcribed, stored in a retrieval system, or translated into any language in any form or by any means,

except documentation kept by the purchaser for backup purposes, without the express written permission

of ASUSTeK COMPUTER INC. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless

such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the

product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS

OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS

DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,

LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),

EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY

DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR

INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,

AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO

RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS

MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies, and are used only for identication or explanation and to the

owners’ benet, without intent to infringe.

iii

Contents

Notices ..................................................................................................................... viii

Federal Communications Commission Statement ........................................ viii

Canadian Department of Communications Statement ....................................ix

REACH .......................................................................................................ix

Safety information ....................................................................................................... x

Electrical safety ............................................................................................... x

Operation safety .............................................................................................. x

Australia statement notice ...............................................................................xi

How this guide is organized ...........................................................................xii

Where to nd more information ...................................................................... xii

Z11PA-U12 Series specifications summary........................................................... xiv

Chapter 1: Product Introduction

1.1 Welcome! ....................................................................................................1-2

1.2 Package contents ......................................................................................1-2

1.3 Serial number label .................................................................................... 1-3

1.4 Special features..........................................................................................1-3

1.4.1 Product highlights........................................................................1-3

1.4.2 Innovative ASUS features ........................................................... 1-4

Chapter 2: Hardware Information

2.1 Before you proceed ...................................................................................2-2

2.2 Motherboard overview ...............................................................................2-3

2.2.1 Placement direction.....................................................................2-3

2.2.2 Screw holes.................................................................................2-3

2.2.3 Motherboard layout ..................................................................... 2-4

2.2.4 Layout contents ........................................................................... 2-6

2.3 Central Processing Unit (CPU) .................................................................2-8

2.3.1 Installing the CPU and heatsink .................................................. 2-8

2.4 System memory .......................................................................................2-10

2.4.1 Overview ................................................................................... 2-10

2.4.2 Memory Congurations ............................................................. 2-10

2.4.3 Installing a DIMM on a single clip DIMM socket........................ 2-11

Contents

2.5 Expansion slots ........................................................................................2-12

2.5.1 Installing an expansion card......................................................2-12

2.5.2 Conguring an expansion card ................................................. 2-12

2.5.3 Interrupt assignments................................................................2-13

2.5.4 PCI Express x16 slot (x16 link) ................................................. 2-13

2.5.5 PCI Express x8 slot (x8 link) ..................................................... 2-13

2.5.6 PCI Express x8 slot (x4 link) ..................................................... 2-13

2.6 Onboard LEDs .......................................................................................... 2-15

2.7 Jumpers ....................................................................................................2-19

2.8 Connectors ...............................................................................................2-26

2.8.1 Rear panel connectors .............................................................. 2-26

2.8.2 Internal connectors....................................................................2-28

Chapter 3: Powering Up

3.1 Starting up for the first time ......................................................................3-2

3.2 Powering off the computer ........................................................................3-3

3.2.1 Using the OS shut down function ................................................ 3-3

3.2.2 Using the dual function power switch .......................................... 3-3

Chapter 4: BIOS Setup

4.1 Managing and updating your BIOS ..........................................................4-2

4.1.1 ASUS CrashFree BIOS 3 utility................................................... 4-2

4.1.2 ASUS EzFlash Utility................................................................... 4-3

4.1.3 BUPDATER utility ....................................................................... 4-4

4.2 BIOS setup program ..................................................................................4-6

4.2.1 BIOS menu screen ...................................................................... 4-7

4.2.2 Menu bar ..................................................................................... 4-7

4.2.3 Menu items..................................................................................4-8

4.2.4 Submenu items ........................................................................... 4-8

4.2.5 Navigation keys ........................................................................... 4-8

4.2.6 General help................................................................................4-8

4.2.7 Conguration elds ..................................................................... 4-8

4.2.8 Pop-up window............................................................................4-8

4.2.9 Scroll bar ..................................................................................... 4-8

4.3 Main menu ..................................................................................................4-9

4.3.1 System Date [Day xx/xx/xxxx] ..................................................... 4-9

4.3.2 System Time [xx:xx:xx] ............................................................... 4-9

Contents

4.4 Advanced menu .......................................................................................4-10

4.4.1 Trusted Computing.................................................................... 4-10

4.4.2 ACPI Settings ............................................................................ 4-11

4.4.3 Smart Settings...........................................................................4-11

4.4.4 Super IO Conguration ............................................................. 4-12

4.4.5 Serial Port Console Redirection ................................................ 4-12

4.4.6 Onboard LAN ............................................................................ 4-15

4.4.7 APM .......................................................................................... 4-17

4.4.8 PCI Subsystem Settings ........................................................... 4-18

4.4.9 Network Stack Conguration..................................................... 4-22

4.4.10 CSM Conguration .................................................................... 4-23

4.4.11 NVMe Conguration .................................................................. 4-24

4.4.12 USB Conguration .................................................................... 4-24

4.4.13 iSCSI Conguration .................................................................. 4-25

4.4.14 Intel(R) Virtual RAID on CPU .................................................... 4-25

4.5 Platform Configuration menu .................................................................4-26

4.5.1 PCH Conguration .................................................................... 4-26

4.5.2 Miscellaneous Conguration ..................................................... 4-29

4.5.3 Server ME Conguration ........................................................... 4-29

4.5.4 Runtime Error Logging .............................................................. 4-30

4.6 Socket Configuration menu ....................................................................4-31

4.6.1 Processor Conguration............................................................ 4-31

4.6.2 Common RefCode Conguration .............................................. 4-33

4.6.3 UPI Conguration ...................................................................... 4-33

4.6.4 Memory Conguration ............................................................... 4-34

4.6.5 IIO Conguration ....................................................................... 4-35

4.6.6 Advanced Power Management Conguration........................... 4-36

4.7 Event Logs menu .....................................................................................4-39

4.7.1 Change Smbios Event Log Settings ......................................... 4-39

4.7.2 View Smbios Event Log ............................................................ 4-39

4.8 Server Mgmt menu ...................................................................................4-40

4.8.1 System Event Log ..................................................................... 4-40

4.8.2 BMC network conguration ....................................................... 4-41

4.8.3 View System Event Log ............................................................ 4-42

4.9 Security menu ..........................................................................................4-43

4.10 Boot menu ................................................................................................4-46

4.11 Tool menu ................................................................................................. 4-47

4.12 Save & Exit menu ..................................................................................... 4-47

Contents

Chapter 5: RAID Configuration

5.1 RAID configurations ..................................................................................5-2

5.1.1 RAID denitions .......................................................................... 5-2

5.1.2 Installing Serial ATA hard disks .................................................. 5-3

5.1.3 Setting the RAID item in BIOS .................................................... 5-3

5.1.4 RAID conguration utilities .......................................................... 5-3

5.2 Intel® Rapid Storage Technology enterprise SATA/SSATA

Option ROM Utility .....................................................................................5-4

5.2.1 Creating a RAID set .................................................................... 5-5

5.2.2 Deleting a RAID set.....................................................................5-7

5.2.3 Resetting disks to Non-RAID ...................................................... 5-8

5.2.4 Exiting the Intel® Rapid Storage Technology enterprise

SATA/SSATA Option ROM utility ................................................ 5-9

5.2.5 Rebuilding the RAID....................................................................5-9

5.2.6 Setting the Boot array in the BIOS Setup Utility ........................ 5-11

5.3 Intel® Rapid Storage Technology enterprise (Windows) ......................5-12

5.3.1 Creating a RAID set .................................................................. 5-13

5.3.2 Changing a Volume Type..........................................................5-15

5.3.3 Deleting a volume ..................................................................... 5-16

5.3.4 Preferences ............................................................................... 5-17

5.4 Intel® Virtual Raid on CPU in BIOS ......................................................... 5-18

5.4.1 Creating a RAID set .................................................................. 5-19

5.4.2 Deleting a RAID set...................................................................5-21

5.4.3 Installing the RAID controller driver during Windows® 10

OS installation ........................................................................... 5-22

Chapter 6: Driver Installation

6.1 RAID driver installation .............................................................................6-2

6.1.1 Creating a USB ash drive with RAID drive ................................ 6-2

6.1.2 Installing the RAID controller driver............................................. 6-2

6.2 Management applications and utilities installation ................................6-5

6.3 Running the Support DVD .........................................................................6-5

6.4 Intel® chipset device software installation ..............................................6-8

6.5 Installing the Intel® I210 Gigabit Adapters driver ..................................6-10

6.7 Intel® Rapid Storage Technology enterprise 5.0 installation ............... 6-13

vii

Contents

Appendix

Z11PA-U12 Series block diagram .......................................................................... A-2

Z11PA-U12/10G-2S .....................................................................................A-2

Z11PA-U12 ..................................................................................................A-3

Q-Code table ............................................................................................................ A-4

Simplified EU Declaration of Conformity .............................................................. A-6

ASUS contact information ...................................................................................... A-7

viii

Notices

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received including interference that may cause

undesired operation.

Z11PA-U12/10G-2S

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

Z11PA-U12

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used

in accordance with manufacturer’s instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

The use of shielded cables for connection of the monitor to the graphics card is required

to assure compliance with FCC regulations. Changes or modications to this unit not

expressly approved by the party responsible for compliance could void the user’s authority

to operate this equipment.

Canadian Department of Communications Statement

Z11PA-U12/10G-2S

This digital apparatus does not exceed the Class A limits for radio noise emissions from

digital apparatus set out in the Radio Interference Regulations of the Canadian Department of

Communications.

This class A digital apparatus complies with Canadian ICES-003.

Z11PA-U12

This digital apparatus does not exceed the Class B limits for radio noise emissions from

digital apparatus set out in the Radio Interference Regulations of the Canadian Department of

Communications.

This class B digital apparatus complies with Canadian ICES-003.

REACH

Complying with the REACH (Registration, Evaluation, Authorization, and Restriction of

Chemicals) regulatory framework, we publish the chemical substances in our products at

ASUS REACH website at http://csr.asus.com/english/REACH.htm.

Safety information

Electrical safety

• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet

before relocating the system.

• When adding or removing devices to or from the system, ensure that the power cables

for the devices are unplugged before the signal cables are connected. If possible,

disconnect all power cables from the existing system before you add a device.

• Before connecting or removing signal cables from the motherboard, ensure that all power

cables are unplugged.

• Seek professional assistance before using an adapter or extension cord. These devices

could interrupt the grounding circuit.

• Make sure that your power supply is set to the correct voltage in your area. If you are

not sure about the voltage of the electrical outlet you are using, contact your local power

company.

• If the power supply is broken, do not try to x it by yourself. Contact a qualied service

technician or your retailer.

Operation safety

• Before installing the motherboard and adding devices on it, carefully read all the manuals

that came with the package.

• Before using the product, make sure all cables are correctly connected and the power

cables are not damaged. If you detect any damage, contact your dealer immediately.

• To avoid short circuits, keep paper clips, screws, and staples away from connectors,

slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Do not place the product in any area

where it may become wet.

• Place the product on a stable surface.

• If you encounter technical problems with the product, contact a qualied service

technician or your retailer.

DO NOT throw the motherboard in municipal waste. This product has been designed to

enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin

indicates that the product (electrical and electronic equipment) should not be placed in

municipal waste. Check local regulations for disposal of electronic products.

DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol

of the crossed out wheeled bin indicates that the battery should not be placed in municipal

waste.

Australia statement notice

From 1 January 2012 updated warranties apply to all ASUS products, consistent with the

Australian Consumer Law. For the latest product warranty details please visit

https://www.asus.com/support. Our goods come with guarantees that cannot be excluded

under the Australian Consumer Law. You are entitled to a replacement or refund for a major

failure and compensation for any other reasonably foreseeable loss or damage. You are also

entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality

and the failure does not amount to a major failure.

If you require assistance please call ASUS Customer Service 1300 2787 88 or visit us at

https://www.asus.com/support.

xii

About this guide

This user guide contains the information you need when installing and conguring the

motherboard.

How this guide is organized

This user guide contains the following parts:

• Chapter1:ProductIntroduction

This chapter describes the features of the motherboard and the new technologies it

supports.

• Chapter2:HardwareInformation

This chapter lists the hardware setup procedures that you have to perform when

installing system components. It includes description of the switches, jumpers, and

connectors on the motherboard.

• Chapter3:PoweringUp

This chapter describes the power up sequence and ways of shutting down the system.

• Chapter4:BIOSSetup

This chapter tells how to change system settings through the BIOS Setup menus.

Detailed descriptions of the BIOS parameters are also provided.

• Chapter5:RAIDConfiguration

This chapter provides instructions for setting up, creating, and conguring RAID sets

using the available utilities.

• Chapter6:DriverInstallation

This chapter provides instructions for installing the necessary drivers for different

system components.

• Appendix:ReferenceInformation

This appendix includes additional information that you may refer to when conguring

the motherboard.

Where to find more information

Refer to the following sources for additional information and for product and software updates.

1. ASUS websites

The ASUS website provides updated information on ASUS hardware and software

products. Refer to the ASUS contact information.

2. Optional documentation

Your product package may include optional documentation, such as warranty yers,

that may have been added by your dealer. These documents are not part of the

standard package.

xiii

Conventions used in this guide

To ensure that you perform certain tasks properly, take note of the following symbols used

throughout this manual.

DANGER/WARNING: Information to prevent injury to yourself when trying to

complete a task.

CAUTION: Information to prevent damage to the components when trying to

complete a task.

IMPORTANT: Instructions that you MUST follow to complete a task.

NOTE: Tips and additional information to help you complete a task.

Typography

Bold text Indicates a menu or an item to select.

Italics Used to emphasize a word or a phrase.

<Key> Keys enclosed in the less-than and greater-than sign means

that you must press the enclosed key.

Example: <Enter> means that you must press the Enter or

Return key.

<Key1> + <Key2> + <Key3> If you must press two or more keys simultaneously, the key

names are linked with a plus sign (+).

Example: <Ctrl> + <Alt> + <Del>

Command Means that you must type the command exactly as shown,

then supply the required item or value enclosed in brackets.

Example: At DOS prompt, type the command line:

format A:/S

xiv

Z11PA-U12 Series specifications summary

(continued on the next page)

Model Name Z11PA-U12/10G-2S Z11PA-U12

Processor Support /

System Bus

1 x Socket P0 (LGA 3647)

Intel® Xeon® processor Scalable Family - Skylake

Core Logic Intel® C622 PCH Intel® C621 PCH

Form Factor ATX, 12" x 9.6" (EEB Mounting Hole Locations)

ASUS

Features

Fan Speed

Control

Rack Ready

(Rack and

Pedestal dual

use)

ASUS Control

Center

Memory

Total Slots 12 (6-channel per CPU, 12 DIMM per CPU)

Voltage 1.2 V

Capacity Maximum up to 1536GB

Memory Type

DDR4 2666 / 2400 / 2133 RDIMM / LRDIMM / 3DS DIMM

* Refer to www.asus.com for the latest memory AVL update

Memory Size

4GB, 8GB, 16GB, 32GB (RDIMM)

32GB, 64GB (LRDIMM)

64GB, 128GB (LRDIMM 3DS)

Expansion

Slots (follow

SSI Location

number)

Total PCI / PCI-E

Slots 4

Slot Location 1 1 x PCI-E x8 (x4 Gen3 Link)

Slot Location 2 1 x PCI-E x16 (x16 Gen3 Link)

Slot Location 3 1 x PCI-E x8 (x8 Gen3 Link)

Slot Location 4 1 x PCI-E x16 (x16 Gen3 Link)

(Auto switch to x8 Gen3 Link if slot 3 is occupied) (support riser)

Additional Slot 1 M.2(NGFF) support (PCIe x2 Gen3 Link or SATA x1))

Additional Slot 2 Oculink connectors support (PCIe x4 Gen3 on each slot)

Networking LAN

2 x Intel I210AT

2 x 10G SFP+ LAN

(10G SKU only)

1 x Management Port with

2 x USB 2.0 ports

2 x Intel I210AT

1 x Management Port with

2 x USB 2.0 ports

Storage

SATA Controller

Intel® C620 series

13 x SATA 6Gb/s ports (3 x mini SAS HD + 1 x SATA)

1 x M.2 (PCIe x2 Gen3 Link or SATA x1) connector ;

NGFF Type 2280

SAS Upgrade

Optional kits:

ASUS PIKE II 3008 8-port SAS 12G RAID card

ASUS PIKE II 3108 8-port SAS 12G HW RAID card

* Specifications are subject to change without notice.

Z11PA-U12 Series specifications summary

Model Name Z11PA-U12/10G-2S Z11PA-U12

Graphic VGA Aspeed AST2500 64MB

Onboard I/O

Connectors

TPM Header 1

PSU Connector 24-pin SSI power connector + 8-pin SSI 12V

Management

connector Onboard ASMB9-iKVM

USB Connectors 1 x USB 3.0 pin header (up to 2 devices)

1 x USB 2.0 pin header (up to 2 devices)

Fan Header 6 x 4-pin

SMBus 1

Chassis Intruder 1

Front LAN LED 2

Serial Port Header 1

M.2 Connector 1 x NGFF Type 2242, 2260, 2280

VROC Key Header 1

Rear I/O

Connectors

VGA Port 1

External USB Port 2 x USB 3.0 ports

SFP+ 2 x SFP+ —

RJ-45 2 x GbE LAN

1 x Mgmt LAN

Management

Solution

Software ASUS Control Center

Out of Band

Remote

Management

ASMB9-iKVM for KVM-over-Internet

Monitoring CPU Temperature

FAN RPM

Environment

Operation temperature: 10°C ~ 35°C

Non operation temperature: -40°C ~ 70°C

Non operation humidity: 20% ~ 90% (Non condensing)

xvi

Product Introduction

This chapter describes the motherboard features and the new

technologies it supports.

Chapter 1: Product Introduction

1-2 Chapter 1: Product Introduction

1.1 Welcome!

Congratulations and thank you for buying an ASUS® Z11PA-U12 Series motherboard!

The motherboard delivers a host of new features and latest technologies, making it another

standout in the long line of ASUS quality motherboards!

Before you start installing the motherboard and hardware devices on it, check the items in

your package with the list below.

1.2 Package contents

Check your motherboard package for the following items.

If any of the above items is damaged or missing, contact your retailer.

Standard Gift Box Pack Standard Bulk Pack

I/O Shield 1 1

SATA 6G cable 1 -

Application CD Support DVD 1 1 piece per carton

Packaging Quantity 1 piece per carton 10 pieces per carton

Optional items Description

PIKE II 3008 LSI 8-port SAS 12G RAID card

PIKE II 3108 LSI 8-port SAS 12G HW RAID card

PEM-FDR Mellanox ConnectX-3 FDR card

PEB-10G/57840-2S Dual port 10G SFP+ Ethernet Adapter

PEB-10G/57811-1S Single port 10G SFP+ Ethernet Adapter

Z11PA-U12 Series 1-3

1.4 Special features

1.4.1 Product highlights

Latest Processor Technology

The motherboard supports Intel Xeon® processor scalable family which provides compelling

IPC increases for legacy performance improvements, oating point improvement, easier

multi-core programming, and with next-generation processor power management.

Intel® AVX 512

Intel® AVX 512 extends 512-bit vector support for integer vector operations, doubles

xed point arithmetic throughput, adds support for new vector gather, permutes/blend,

vector shifts resulting in xed and oating-point algorithm improvements. Also, Intel's new

microarchitecture doubles the cache bandwidth at L1/L2 to support higher FLOPS and

contributes to greater performance in signal and image processing applications.

Next Generation of processor power management

Intel® Xeon processor scalable family enhances the processor power management with the

features of Energy Efcient Turbo, Uncore Frequency Scaling, and Per-Core P-state. Also,

the Integrated Voltage Regulator enables generational performance and power improvements

that the standard VR solutions cannot provide.

DDR4 memory support

The motherboard supports DDR4 memory that features faster clock frequencies and higher

data transfer rates of 2133 MT/s to 2666 MT/s (million transfers per second). DDR4 offers a

lower voltage standard of 1.2V that reduces memory power demand and provides improved

performance.

1.3 Serial number label

Before requesting support from the ASUS Technical Support team, you must take note of

the motherboard's serial number containing 12 characters xxS2xxxxxxxx shown in the gure

below. With the correct serial number of the product, ASUS Technical Support team members

can then offer a quicker and satisfying solution to your problems.

xxS2xxxxxxxx

Z11PA-U12 Series Made

China

合格

1-4 Chapter 1: Product Introduction

M.2 Support

This motherboard features the M.2 slot, which shares bandwidth with the SATA 6Gb/s port

and is dedicated to the operating system.

PCI Express 3.0

PCI Express 3.0 (PCIe 3.0) is the PCI Express bus standard that provides an optimal

graphics performance, unprecedented data speed, and seamless transition with its complete

backward compatibility to PCIe 2.0 devices.

Intel® I210AT LAN Solution

The motherboard comes with two Gigabit LAN controllers and ports which provide a total

solution for your networking needs. The onboard Intel® I210AT Gigabit LAN controllers use

the PCI Express interface and could achieve network throughput close to Gigabit bandwidth.

Intel® C620 Series Chipset

The Intel® C620 series chipset supports with enterprise class features which is targeted for

Cloud and Storage applications. It is optimized and validated to work with the latest Xeon®

processor scalable family, compared with the last generation, it also reduces the TDP,

supports USB 3.0 with up to 14 ports for SATA and SSATA thus bringing more features and

benets to the target users.

Serial ATA III technology

The motherboard supports the Serial ATA III technology through the Serial ATA interface

and Intel® C621 / C622 chipset, delivering up to 6 Gb/s data transfer rates. It also provides

enhanced scalability, faster data retrieval, and double the bandwidth of current bus systems.

Temperature, fan, and voltage monitoring

The CPU temperature is monitored to prevent overheating and damage. The system fan

rotations per minute (RPM) is monitored for timely failure detection. The chip monitors the

voltage levels to ensure a stable supply of current for critical components.

1.4.2 Innovative ASUS features

ASUS Fan Speed control technology

The ASUS Fan Speed control technology smartly adjusts the fan speeds according to the

system loading to ensure a quiet, cool, and efcient operation.

Hardware Information

This chapter lists the hardware setup procedures that you have

to perform when installing system components. It includes

description of the jumpers and connectors on the motherboard.

Chapter 2: Hardware Information

2-2 Chapter 2: Hardware Information

2.1 Before you proceed

Take note of the following precautions before you install any motherboard component or

change any motherboard settings.

• Unplugthepowercordfromthewallsocketbeforetouchinganycomponent.

• Useagroundedwriststraportouchasafelygroundedobjectorametalobject,such

asthepowersupplycase,beforehandlingcomponentstoavoiddamagingthemdue

to static electricity.

• HoldcomponentsbytheedgestoavoidtouchingtheICsonthem.

• Wheneveryouuninstallanycomponent,placeitonagroundedantistaticpadorinthe

bag that came with the component.

• Beforeyouinstallorremoveanycomponent,ensurethatthepowersupplyisswitched

off or the power cord is detached from the power supply. Failure to do so may cause

severedamagetothemotherboard,peripherals,and/orcomponents.

2-3

Z11PA-U12 Series

2.2 Motherboard overview

Beforeyouinstallthemotherboard,studythecongurationofyourchassistoensurethatthe

motherboardtsintoit.

Tooptimizethefeaturesofyourmotherboard,wehighlyrecommendthatyouinstallitinan

ATX 2.2 compliant chassis.

2.2.1 Placement direction

Wheninstallingthemotherboard,ensurethatyouplaceitintothechassisinthecorrect

orientation. The edge with external ports goes to the rear part of the chassis as indicated in

the image below.

2.2.2 Screw holes

Place nine (9) screws into the holes indicated by circles to secure the motherboard to the

chassis.

DO NOT overtighten the screws! Doing so can damage the motherboard.

Ensure to unplug the chassis power cord before installing or removing the motherboard.

Failure to do so can cause you physical injury and damage motherboard components!

Place this side towards

the rear of the chassis

2-4 Chapter 2: Hardware Information

2.2.3 Motherboard layout

Z11PA-U12/10G-2S

2-5

Z11PA-U12 Series

Z11PA-U12

2-6 Chapter 2: Hardware Information

2.2.4 Layout contents

Slots/Sockets Page

1. CPUsocket 2-8

2. DDR4 sockets 2-10

3. PCIExpressx16/PCIExpressx8 2-12

Onboard LEDs Page

1. StandbyPowerLED(SBPWR1) 2-16

2. BaseboardManagementControllerLED(BMCLED1) 2-16

3. CATTLED(CATERR1) 2-17

4. HarddiskactivityLED(HDDLED1) 2-17

5. MessageLED(MESLED1) 2-18

6. LocationLED(LOCLED1) 2-18

7. Q-CodeLEDs(PORT80_LED1) 2-19

Jumpers Page

1. ClearRTCRAM(CLRTC1) 2-19

2. VGAcontrollersetting(3-pinVGA_SW1) 2-20

3. LANcontrollersetting(3-pinLAN_SW1,LAN_SW2) 2-20

4. MErmwareforcerecoverysetting(3-pinME_RCVR1) 2-21

5. DDR4thermaleventsetting(3-pinDIMMTRIP1) 2-21

6. PCH_MFG1setting(3-pinPCH_MFG1) 2-22

7. SmartRideThrough(SmaRT)setting(3-pinSMART_PSU1) 2-22

8. DMLANsetting(3-pinDM_IP_SEL1) 2-23

9. IPMISWsetting(3-pinIPMI_SW1) 2-23

10. BaseboardManagementControllersetting(3-pinBMC_EN1) 2-24

11. 10GbELANsetting(3-pinSU1NCSI_EN1)(forZ11PA-U12/10G-2Sonly) 2-24

12. LANNCSIsetting(3-pinLAN1_NCSI_EN;LAN2_NCSI_EN) 2-25

2-7

Z11PA-U12 Series

Internal connectors Page

1. SerialATA6.0/3.0Gb/sconnector(7-pinSSATA1) 2-28

2. Mini-SASHDconnector(ISATA1-2;ISSATA1) 2-28

3. M.2(NGFF)connector(NGFF1) 2-29

4. TrustedPlatformModuleconnector(14-1pinTPM1) 2-29

5. USB2.0connector(10-1pinUSB56) 2-30

6. USB3.0connector(20-1pinUSB3_34) 2-30

7. PowerSupplySMBusconnector(5-pinPSUSMB1) 2-31

8. Serialportconnector(10-1pinCOM1) 2-31

9. CPU,front,andrearfanconnectors(4-pinCPU_FAN1,FRNT_FAN1-4,

REAR_FAN1) 2-32

10. HarddiskactivityLEDconnector(4-pinHDLED1) 2-32

11. EATXpowerconnectors(24-pinEATXPWR,8-pinEATX12V1) 2-33

12. LAN34_LEDconnector(5-1pinLAN34_LED1) 2-33

13. System panel connector (20-1 pin PANEL1) 2-34

14. Auxiliarypanelconnector(20-2pinAUX_PANEL1) 2-35

15. VPP_I2C1connector(10-1pinVPP_I2C1) 2-36

16. ChassisIntrusion(2-pinINTRUSION) 2-36

17. OCUPCIEconnectors(OCUPCIE1-2) 2-37

18. SystemManagementBus(SMBUS)connectors(5-1pinSMBUS1;

6-1pinSMBUS2) 2-37

19. SerialGeneralPurposeInput/Outputconnector(6-1pinSSGPIO1) 2-38

20. VGAconnector(16-pinVGA_HDR1) 2-38

21. VROC_KEYconnector(4-pinVROC_KEY1) 2-39

22. Thermal sensor cable connector (3-pin TR1) 2-39

2-8 Chapter 2: Hardware Information

2.3.1 Installing the CPU and heatsink

ToinstallaCPU:

1. LocatetheCPUsocketonthemotherboard.

2.3 Central Processing Unit (CPU)

The motherboard comes with a surface mount Socket P0 (LGA 3647) designed for the Intel®

Xeon® processor Skylake-SP product family.

• Uponpurchaseofthemotherboard,ensurethatthePnPcapisonthesocketand

thesocketcontactsarenotbent.ContactyourretailerimmediatelyifthePnPcap

ismissing,orifyouseeanydamagetothePnPcap/socketcontacts/motherboard

components.ASUSwillshoulderthecostofrepaironlyifthedamageisshipment/

transit-related.

• Keepthecapafterinstallingthemotherboard.ASUSwillprocessReturnMerchandise

Authorization(RMA)requestsonlyifthemotherboardcomeswiththecaponthe

Socket P0 (LGA 3647).

• Theproductwarrantydoesnotcoverdamagetothesocketcontactsresultingfrom

incorrectCPUinstallation/removal,ormisplacement/loss/incorrectremovalofthePnP

cap.

BeforeinstallingtheCPU,ensurethatthesocketboxisfacingtowardyouandthetriangle

mark is on the top-right position.

2. RemovethePNPcapfromtheCPUsocket.

2-9

Z11PA-U12 Series

3. AlignthetrianglemarkontheCPUwiththe

trianglemarkontheCPUCarrier(A),theninstall

theCPUintotheCPUCarrieruntilitclicksrmly

intoplace(B),andtheninstalltheCPUCarrier

intotheheatsinkuntilitclicksrmlyinplace(C).

EnsurethatthetrianglemarkontheCPU

matchesthetrianglemarkontheCPUCarrier.

ApplytheThermalInterfaceMaterialtotheCPU

heatsinkandCPUbeforeyouinstalltheheatsink

andfan,ifnecessary.

4. Twist each of the four screws with a screwdriver

just enough to attach the heatsink to the

motherboard.Whenthefourscrewsareattached,

tightenthemonebyoneinadiagonalsequence

to completely secure the heatsink.

CPU Carrier

CPU

Triangle mark

TheCPUandheatsinkassemblytsinonlyone

correctorientation.DONOTforcetheCPUand

heatsink assembly into the socket to prevent

damagingtheCPUpinsonthesocket.

TheheatsinkscrewsareT30models.Atorque

value of 12 inch-lbf is recommended.

2-10 Chapter 2: Hardware Information

2.4 System memory

2.4.1 Overview

Themotherboardcomeswithtwelve(12)DoubleDataRate4(DDR4)DualInlineMemory

Modules(DIMM)sockets.

ThegureillustratesthelocationoftheDDR4DIMMsockets:

2.4.2 Memory Configurations

Youmayinstall4GB,8GB,16GB,and32GBRDIMMsor32GBand64GBLR-DIMMsinto

theDIMMsocketsusingthememorycongurationsinthissection.

• RefertoASUSServerAVLfortheupdatedlistofcompatibleDIMMs.

• WheninstallingDIMMs,alwaysstartfromslotA1.

• AlwaysinstallDIMMswiththesameCASlatency.Foroptimumcompatibility,itis

recommended that you obtain memory modules from the same vendor.

Recommended Memory configuration

DIMM

A2 A1 B2 B1 C2 C1 D2 D1 E2 E1 F2 F1

1 DIMM -P----------

2 DIMMs -P-----P----

4 DIMMs -P-P---P-P- -

6 DIMMs -P-P-P-P-P-P

8 DIMMs P P -P-PPP -P-P

12 DIMMs P P PPPPPPPPPP

Youcanrefertothefollowingrecommendedmemorypopulation:

2-11

Z11PA-U12 Series

2.4.3 Installing a DIMM on a single clip DIMM socket

3. HoldtheDIMMatbothendsthen

inserttheDIMMintothesocket.

ApplyforcetobothendsoftheDIMM

simultaneously until the retaining clip

clicksintoplaceandtheDIMMis

seated securely in place.

1. Press the retaining clip outward to

unlocktheDIMMsocket.

2. AlignaDIMMonthesocketsuchthat

thenotchontheDIMMmatchesthe

DIMMslotkeyonthesocket.

Unlocked retaining clip

DIMM notch

DIMM slot key

1. Press the retaining clip outward to

unlocktheDIMM.

2. RemovetheDIMMfromthesocket.

Removing a DIMM from a single clip DIMM socket

• ToinstalltwoormoreDIMMs,refertotheuserguidebundledwiththemotherboard

package.

• Refertotheuserguideforqualiedvendorlistsofthememorymodules.

SupporttheDIMMlightlywithyourngerswhenpressingtheretainingclips.TheDIMM

mightgetdamagedwhenitipsoutwithextraforce.

AlwaysinserttheDIMMintothesocketVERTICALLYtopreventDIMMnotchdamage.

ADIMMiskeyedwithanotchsothatittsinonlyonedirection.DONOTforceaDIMMinto

asocketinthewrongdirectiontoavoiddamagingtheDIMM.

Locked Retaining Clip

2-12 Chapter 2: Hardware Information

2.5 Expansion slots

Inthefuture,youmayneedtoinstallexpansioncards.Thefollowingsubsectionsdescribethe

slots and the expansion cards that they support.

2.5.1 Installing an expansion card

Toinstallanexpansioncard:

1. Beforeinstallingtheexpansioncard,readthedocumentationthatcamewithitand

make the necessary hardware settings for the card.

2. Remove the system unit cover (if your motherboard is already installed in a chassis).

3. Removethebracketoppositetheslotthatyouintendtouse.Keepthescrewforlater

use.

4. Alignthecardconnectorwiththeslotandpressrmlyuntilthecardiscompletely

seated on the slot.

5. Secure the card to the chassis with the screw you removed earlier.

6. Replace the system cover.

2.5.2 Configuring an expansion card

Afterinstallingtheexpansioncard,congureitbyadjustingthesoftwaresettings.

1. TurnonthesystemandchangethenecessaryBIOSsettings,ifany.SeeChapter 4 for

informationonBIOSsetup.

2. Assign an IRQ to the card.

Refer to the table Standard Interrupt assignments in section Interrupt assignments for

more information.

3. Install the software drivers for the expansion card.

Ensure to unplug the power cord before adding or removing expansion cards. Failure to do

so may cause you physical injury and damage motherboard components.

WhenusingPCIecardsonsharedslots,ensurethatthedriverssupport“ShareIRQ”orthat

thecardsdonotneedIRQassignments.Otherwise,conictsmayarisebetweenthetwo

PCIegroups,makingthesystemunstableandthecardinoperable.

2-13

Z11PA-U12 Series

*TheseIRQsareusuallyavailableforISAorPCIdevices.

IRQ Priority Standard function

0 1 System Timer

1 2 KeyboardController

2 - Programmable Interrupt

3* 11 CommunicationsPort(COM2)

4* 12 CommunicationsPort(COM1)

5* 13 --

6 14 FloppyDiskController

7* 15 --

8 3 SystemCMOS/RealTimeClock

9* 4 ACPIModewhenused

10* 5 IRQHolderforPCISteering

11* 6 IRQHolderforPCISteering

12* 7 PS/2CompatibleMousePort

13 8 Numeric Data Processor

14* 9 PrimaryIDEChannel

15* 10 SecondaryIDEChannel

2.5.3 Interrupt assignments

Standard Interrupt assignments

2.5.4 PCI Express x16 slot (x16 link)

TheonboardPCIE4andPCIE2slotsprovidetwox16Gen3linktoCPU1andonlyPCIE4

supportsautoswitchestox8linkifPCIE3isoccupied.ThesetwoslotssupportVGAcards

and various server class high performance add-on cards.

2.5.5 PCI Express x8 slot (x8 link)

TheonboardPCIE3slotprovidesonex8Gen3linktoCPU1.ThisslotsupportsVGAcards

and various server class high performance add-on cards.

2.5.6 PCI Express x8 slot (x4 link)

TheonboardPCIE1slotprovidesonex4Gen3linktoCPU1Thisslotsupportsvariousserver

class high performance add-on cards.

2-14 Chapter 2: Hardware Information

No. (Slot location) Short description

1PCIE4

PCI-Ex16(x16Gen3Link)

(Auto switch to x8 Gen3 Link if slot 3 is occupied)

(support riser)

2PCIE3 PCI-Ex8(x8Gen3Link)

3PCIE2 PCI-Ex16(x16Gen3Link)

4PCIE1 PCI-Ex8(x4Gen3Link)

2-15

Z11PA-U12 Series

2. Baseboard Management Controller LED (BMCLED1)

ThegreenheartbeatLEDblinkspersecondtoindicatethattheASMB9isworking

normally.

2.6 Onboard LEDs

1. Standby Power LED (SBPWR1)

The motherboard comes with a standby power LED. The green LED lights up to

indicatethatthesystemisON,insleepmode,orinsoft-offmode.Thisisareminder

that you should shut down the system and unplug the power cable before removing or

plugging in any motherboard component. The illustration below shows the location of

the onboard LED.

2-16 Chapter 2: Hardware Information

3. CATT LED (CATERR1)

TheCATTLEDindicatesthatthesystemhasexperiencedafatalorcatastrophicerror

and cannot continue to operate.

4. Hard disk activity LED (HDDLED1)

ThisLEDisforthestoragedevicesconnectedtotheonboardSATA,orSATA/SAS

add-oncard.ThereadorwriteactivitiesofanydeviceconnectedtotheonboardSATA,

orSATA/SASadd-oncardcausestherearpanelLEDtolightup.

2-17

Z11PA-U12 Series

6. Location LED (LOCLED1)

This onboard LED lights up when the Location button on the server is pressed or when

triggered by a system management software. The Location LED helps visually locate

andquicklyidentifytheserverinerroronaserverrack.

5. Message LED (MESLED1)

ThisonboardLEDlightsuptoredwhenthereisaBMCeventlogisgenerated.

2-18 Chapter 2: Hardware Information

7. Q-Code LEDs (PORT80_LED1)

TheQ-CodeLEDprovidesa2-digitdisplaythatshowsthestatusofyoursystem.

• TheQ-CodeLEDsprovidethemostprobablecauseofanerrorcodeasastarting

point for troubleshooting. The actual cause may vary from case to case.

• PleaserefertotheQ-CodetableintheAppendix section for more details.

2-19

Z11PA-U12 Series

2.7 Jumpers

1. Clear RTC RAM (3-pin CLRTC1)

ThisjumperallowsyoutocleartheRealTimeClock(RTC)RAMinCMOS.Youcan

cleartheCMOSmemoryofdate,time,andsystemsetupparametersbyerasingthe

CMOSRTCRAMdata.TheonboardbuttoncellbatterypowerstheRAMdatainCMOS

which include system setup information such as system passwords.

ToerasetheRTCRAM:

1. Turn OFF the computer and unplug the power cord.

2. Movethejumpercapfromthedefaultpins1–2topins2–3.Keepthecaponpins

2–3forabout5to10seconds,thenmovethecapbacktopins1–2.

3. Plug the power cord and turn ON the computer.

4. Holddownthe<Del>keyduringthebootprocessandenterBIOSsetuptore-

enter data.

DONOTremovethecaponCLRTC1jumperdefaultpositionexcept when clearing the

RTCRAM. Removing the cap will cause system boot failure!

Ifthestepsabovedonothelp,removetheonboardbatteryandmovethejumperagainto

cleartheCMOSRTCRAMdata.AftertheCMOSclearance,reinstallthebattery.

2-20 Chapter 2: Hardware Information

2. VGA controller setting (3-pin VGA_SW1)

ThisjumperallowsyoutoenableordisabletheonboardVGAcontroller.Settopins1–2

to activate the VGA feature.

3. LAN controller setting (3-pin LAN_SW1, LAN_SW2)

ThesejumpersallowyoutoenableordisabletheonboardLAN_SW1orLAN_SW2.

Set to pins 1–2 to activate the Gigabit LAN feature.

2-21

Z11PA-U12 Series

4. ME firmware force recovery setting (3-pin ME_RCVR1)

This jumper allows you to force Intel®ManagementEngine(ME)bootfromrecovery

modewhenMEbecomescorrupted.

5. DDR4 thermal event setting (3-pin DIMMTRIP1)

ThisjumperallowsyoutoenableordisableDDR4DIMMthermalsensingeventpin.

2-22 Chapter 2: Hardware Information

6. PCH_MFG1 setting (3-pin PCH_MFG1)

ThisjumperallowsyoutoupdatetheBIOSMEblock.

7. Smart Ride Through (SmaRT) setting (3-pin SMART_PSU1)

This jumper allows you to enable or disable the Smart Ride Through (SmaRT) function.

Thisfeatureisdisabledbydefault.Settopins1-2toenableit.Whenenabled,SmaRT

allowsuninterruptedoperationofthesystemduringanAClossevent.

2-23

Z11PA-U12 Series

8. DMLAN setting (3-pin DM_IP_SEL1)

ThisjumperallowsyoutoselecttheDMLANsetting.Settopins2-3toforcethe

DMLANIPtostaticmode(IP=10.10.10.10,submask=255.255.255.0).

9. IPMI SW setting (3-pin IPMI_SW1)

ThisjumperallowsyoutoselectwhichprotocolintheGPUsensortofunction.

2-24 Chapter 2: Hardware Information

10. Baseboard Management Controller setting (3-pin BMC_EN1)

Thisjumperallowsyoutoenable(default)ordisableon-boardBMC.Ensuretosetthis

BMCjumpertoenabledtoavoidsystemfancontrolandhardwaremonitorerror.

11. 10GbE LAN setting (3-pin SU1NCSI_EN1) (for Z11PA-U12/10G-2S only)

Thisjumperallowsyoutoenable10GbEshareLANonBMC.

2-25

Z11PA-U12 Series

12. LANNCSI setting (3-pin LAN1_NCSI_EN; LAN2_NCSI_EN)

ThisjumperallowsyoutoselectwhichLANNCSItofunction.

For Z11PA-U12/10G-2S

For Z11PA-U12

2-26 Chapter 2: Hardware Information

2.8 Connectors

2.8.1 Rear panel connectors

1. Video Graphics Adapter (VGA) port: This port is for a VGA monitor or other VGA-

compatible devices..

2. SFP+ LEDs (only available for Z11PA U12/10G-2S): These LEDs indicate the link

status and the link speed of the SFP+ ports. Refer to the table below for the SFP+ LED

indications.

3. Power-on Button: Press this button to turn on the system.

4. RJ-45 port for iKVM:ThisRJ-45portfunctionswhenyouenabletheASMB8

controller.

5. RJ-45 ports for LAN 1 and 2: These ports allow Gigabit connection to a LAN through

a network hub. Refer to the LAN port LED indications table for more information.

6. SFP+ ports (only available for Z11PA U12/10G-2S): These ports are for connecting

the enhanced small form-factor pluggable (SFP+) module that supports data rates up

to 10 Gbps.

7. USB 3.0 ports 1 and 2: Thesetwo4-pinUniversalSerialBus(USB)portsareavailable

forconnectingUSB3.0devices.

2-27

Z11PA-U12 Series

SPEED

LED

ACT/LINK

LED

Activity/Link LED Speed LED

Status Description Status Description

OFF No link OFF 10Mbpsconnection

ORANGE Linked ORANGE 100Mbpsconnection

BLINKING Data activity GREEN 1 Gbps connection

Activity/Link LED Speed LED

Status Description Status Description

OFF No link OFF 10Mbpsconnection

GREEN Linked ORANGE 100Mbpsconnection

BLINKING Data activity GREEN 1 Gbps connection

Management LAN port LED indications

SFP+_LED indications (only available for Z11PA U12/10G-2S)

Activity LED Speed LED

Status Description Status Description

OFF No activity OFF -

BLINKING Data activity AMBER 1 Gbps connection

GREEN 10 Gbps connection

SFP+ LED

Speed LED

Activity LED

LAN1/LAN2 LEDs

ACT/LINK

LED SPEED

LED

2-28 Chapter 2: Hardware Information

2.8.2 Internal connectors

1. Serial ATA connectors (7-pin SSATA1)

Thisconnector,controlledbyIntel®C620chipset,isfortheSerialATAsignalcablefor

Serial ATA hard disk drives.

2. Mini-SAS HD connector (ISATA1-2; ISSATA1)

ThismotherboardcomeswithminiSerialAttachedSCSI(SAS)HDconnectors,the

storage technology that supports Serial ATA. Each connector supports up to four

devices.

2-29

Z11PA-U12 Series

3. M.2 (NGFF) connector (NGFF1)

ThisconnectorallowsyoutoinstallanM.2device.

Thisconnectorsupportstype2242/2260/2280devicesonbothPCI-E(2lanesonly)and

SATA interface.

TheM.2(NGFF)deviceispurchasedseparately.

4. Trusted Platform Module connector (14-1 pin TPM1)

ThisconnectorsupportsaTrustedPlatformModule(TPM)system,whichcansecurely

storekeys,digitalcerticates,passwords,anddata.ATPMsystemalsohelpsenhance

networksecurity,protectsdigitalidentities,andensuresplatformintegrity.

2-30 Chapter 2: Hardware Information

5. USB 2.0 connector (10-1 pin USB56)

ThisconnectorisforUSB2.0ports.ConnecttheUSBmodulecabletotheconnector,

and then install the module to a slot opening at the back of the system chassis. The

USBconnectorscomplywithUSB2.0specicationthatsupportsupto480Mbps

connection speed.

6. USB 3.0 connector (20-1 pin USB3_34)

ThisconnectorallowsyoutoconnectaUSB3.0moduleforadditionalUSB3.0front

orrearpanelports.WithaninstalledUSB3.0module,youcanenjoyallthebenetsof

USB3.0includingfasterdatatransferspeedsofupto5Gbps,fasterchargingtimefor

USB-chargeabledevices,optimizedpowerefciency,andbackwardcompatibilitywith

USB2.0.

TheUSBportmoduleispurchasedseparately.

2-31

Z11PA-U12 Series

7. Power Supply SMBus connector (5-pin PSUSMB1)

ThisconnectorallowsyoutoconnectSMBus(SystemManagementBus)tothePSU

(powersupplyunit)toreadPSUinformation.DevicescommunicatewithanSMBus

hostand/orotherSMBusdevicesusingtheSMBusinterface.

PowersupplyisrequiredtomeetPMBusspecicationandcustomizedBMCFWmaybe

needed.PleasecontactASUSifyourneedfurthersupport.

8. Serial port connector (10-1 pin COM1)

ThisconnectorisfortheserialCOMport.Connecttheserialportmodulecabletoone

oftheseconnectors,theninstallthemoduletoaslotopeningatthebackofthesystem

chassis.

TheCOMmoduleispurchasedseparately.

2-32 Chapter 2: Hardware Information

9. CPU, front, and rear fan connectors (4-pin CPU_FAN1, FRNT_FAN1-4,

REAR_FAN1)

Thefanconnectorssupportcoolingfans.Connectthefancablestothefanconnectors

onthemotherboard,ensuringthattheblackwireofeachcablematchesthegroundpin

of the connector.

• DONOTforgettoconnectthefancablestothefanconnectors.Insufcientairow

inside the system may damage the motherboard components.

• Thesearenotjumpers!DONOTplacejumpercapsonthefanconnectors!

• AllfansfeaturetheASUSSmartFantechnology.

10. Hard disk activity LED connector (4-pin HDLED1)

This LED connector is for the storage add-on card cable connected to the SATA or

SAS add-on card. The read or write activities of any device connected to the SATA or

SAS add-on card causes the front panel LED to light up.

2-33

Z11PA-U12 Series

11. EATX power connectors (24-pin EATXPWR, 8-pin EATX12V1)

These connectors are for the SSI or ATX power supply plugs. The power supply plugs

aredesignedtottheseconnectorsinonlyoneorientation.Findtheproperorientation

andpushdownrmlyuntiltheconnectorscompletelyt.

• DONOTforgettoconnectthe24+8-pinpowerplugswhenusing85WorbelowCPU;

otherwise,thesystemwillnotbootup.

• UseofaPSUwithahigherpoweroutputisrecommendedwhenconguringasystem

with more power-consuming devices. The system may become unstable or may not

bootupifthepowerisinadequate.

• Ensurethatyourpowersupplyunit(PSU)canprovideatleasttheminimumpower

requiredbyyoursystem.

12. LAN34_LED connector (5-1 pin LAN34_LED1)

TheseLEDsareforGigabitLANactivityLEDsonthefrontpanel.ConnecttheLAN

LED cable to the backplane for LAN activity indication.

2-34 Chapter 2: Hardware Information

13. System panel connector (20-1 pin PANEL1)

This connector supports several chassis-mounted functions.

1. System power LED (3-pin PLED)

 This3-pinconnectorisforthesystempowerLED.Connectthechassispower

LED cable to this connector. The system power LED lights up when you turn on

thesystempower,andblinkswhenthesystemisinsleepmode.

2. Message LED (2-pin MLED)

This 2-pin connector is for the message LED cable that connects to the front

messageLED.ThemessageLEDiscontrolledbyHardwaremonitortoindicate

an abnormal event occurance.

3. System warning speaker (4-pin SPEAKER)

This 4-pin connector is for the chassis-mounted system warning speaker. The

speaker allows you to hear system beeps and warnings.

4. Hard disk drive activity LED (2-pin HDD LED)

 This2-pinconnectorisfortheHDDActivityLED.ConnecttheHDDActivityLED

cabletothisconnector.TheHDLEDlightsuporasheswhendataisreadfrom

orwrittentotheHDD.

5. Power button/soft-off button (2-pin PWRSW)

This connector is for the system power button. Pressing the power button turns

thesystemonorputsthesysteminsleeporsoft-offmodedependingontheBIOS

settings. Pressing the power switch for more than four seconds while the system

is ON turns the system OFF.

6. Reset button (2-pin RESET)

This 2-pin connector is for the chassis-mounted reset button for system reboot

without turning off the system power.

2-35

Z11PA-U12 Series

14. Auxiliary panel connector (20-2 pin AUX_PANEL1)

ThisconnectorisforadditionalfrontpanelfeaturesincludingfrontpanelSMB,locator

LEDandswitch,andLANLEDs.

1. Front panel SMB (10-2 pin FPSMB)

 TheseconnectorsareforthefrontpanelSMBuscable.

2. LAN activity LED (2-pin LAN1_LED, LAN2_LED)

These connectors are for Gigabit LAN activity LEDs on the front panel.

3. Locator LED (2-pin LOCATORLED1, LOCATORLED2)

 TheseconnectorsareforthelocatorLED1andLED2onthefrontpanel.Connect

the Locator LED cables to these 2-pin connector. The LEDs will light up when the

Locator button is pressed.

4. Locator Button/Switch (2-pin LOCATORBTN)

 Theseconnectorsareforthelocatorbuttononthefrontpanel.Thisbuttonqueries

the state of the system locator.

2-36 Chapter 2: Hardware Information

16. Chassis Intrusion (2-pin INTRUSION1)

These leads are for the intrusion detection feature for chassis with intrusion sensor or

microswitch.Whenyouremoveanychassiscomponent,thesensortriggersandsends

a high level signal to these leads to record a chassis intrusion event. The default setting

isshortCHASSIS#andGNDpinbyjumpercaptodisablethefunction.

15. VPP_I2C1 connector (10-1 pin VPP_I2C1)

ThisconnectorisusedfortheIntelVMDfunctionandsensorreadings.

2-37

Z11PA-U12 Series

17. OCUPCIE connectors (OCUPCIE1-2)

ConnectsthePCIEsignaltothefrontrisercardorNVMEportonthebackplane.

18. System Management Bus (SMBUS) connectors (5-1 pin SMBUS1; 6-1 pin SMBUS2)

These connectors control the system and power management-related tasks. These

connectors process the messages to and from devices rather than tripping the individual

control lines.

2-38 Chapter 2: Hardware Information

19. Serial General Purpose Input/Output connector (6-1 pin SSGPIO1)

The SSGPIO 1 connector is used for the Intel Rapid Storage Technology Enterprise

SGPIOinterfacethatcontrolstheLEDpatterngeneration,deviceinformation,and

general purpose data.

20. VGA connector (16-pin VGA_HDR1)

ThisconnectorsupportstheVGAHighDynamic-Rangeinterface.

2-39

Z11PA-U12 Series

21. VROC_KEY connector (4-pin VROC_KEY1)

ThisconnectorallowsyoutoconnectaKEYmoduletosupportIntelVMDRAID

function.

22. Thermal sensor cable connector (3-pin TR1)

This connector allows you to connect a Thermal sensor cable that is used for

temperaturemonitoring.ConnecttheThermalsensorcabletotheconnectorandplace

its probe to the device that you want to check the temperature.

2-40 Chapter 2: Hardware Information

Powering Up

This chapter describes the power up sequence, and ways of

shutting down the system.

Chapter 3: Powering Up

3-2 Chapter 3: Powering Up

3.1 Starting up for the first time

1. After making all the connections, replace the system case cover.

2. Be sure that all switches are off.

3. Connect the power cord to the power connector at the back of the system chassis.

4. Connect the power cord to a power outlet that is equipped with a surge protector.

5. Turn on the devices in the following order:

a. Monitor

b. External storage devices (starting with the last device on the chain)

c. System power

6. After applying power, the system power LED on the system front panel case lights up.

For systems with ATX power supplies, the system LED lights up when you press the

ATX power button. If your monitor complies with “green” standards or if it has a “power

standby” feature, the monitor LED may light up or switch between orange and green

after the system LED turns on.

The system then runs the power-on self-test or POST. While the tests are running, the

BIOS beeps or additional messages appear on the screen. If you do not see anything

within 30 seconds from the time you turned on the power, the system may have failed

a power-on test. Check the jumper settings and connections or call your retailer for

assistance.

The following shows the possible beep codes and its corresponding error condition

BIOS Beep codes

Beep Error condition

1 short Power supply surges detected during the previous power on.

1 short No Keyboard Detected.

1 short, 2 short No DIMM Detected.

1 short, 8 short No VGA Detected.

2 long Chassis Intrusion.

2 long BIOS-image Crash Detected.

7. At power on, hold down the <Del> key to enter the BIOS Setup. Follow the instructions

in Chapter 4.

3-3

Z11PA-U12 Series

3.2 Powering off the computer

3.2.1 Using the OS shut down function

Using Windows® Server 2012 R2:

1. Press <Ctrl>+<Alt>+<Del>.

2. Click on the Power icon on the lower right side of the screen.

3. Select

Shut down.

4. In the Shutdown Event Tracker, select the Other (Planned) option in the selection

lists. Otherwise, select the option that best describes why you want to shut down the

computer.

5. Click

Continue.

Using Windows® Server 2016:

1. Press <Alt>+<F4>.

2. In the What do you want the computer to do?, select Shut down.

3. In the Shutdown Event Tracker, select the Other (Planned) option in the selection

list. Otherwise, select the option that best describes why you want to shut down the

computer.

4. Click

OK.

3.2.2 Using the dual function power switch

While the system is ON, press the power switch for less than four seconds to put the system

to sleep mode or to soft-off mode, depending on the BIOS setting.

Pressing the power switch for more than four seconds lets the system enter the soft-off

mode regardless of the BIOS setting.

3-4 Chapter 3: Powering Up

BIOS Setup

This chapter tells how to change the system settings through

the BIOS Setup menus. Detailed descriptions of the BIOS

parameters are also provided.

Chapter 4: BIOS Setup

4-2 Chapter 4: BIOS Setup

4.1 Managing and updating your BIOS

The following utilities allow you to manage and update the motherboard Basic Input/Output

System (BIOS) setup:

1. ASUS CrashFree BIOS 3

 TorecovertheBIOSusingabootableUSBashdiskdrivewhentheBIOSlefailsor

gets corrupted.

2. ASUS EzFlash

 UpdatestheBIOSusingaUSBashdisk.

3. BUPDATER

 UpdatestheBIOSinDOSmodeusingabootableUSBashdiskdrive.

Refer to the corresponding sections for details on these utilities.

4.1.1 ASUS CrashFree BIOS 3 utility

TheASUSCrashFreeBIOS3isanautorecoverytoolthatallowsyoutorestoretheBIOSle

when it fails or gets corrupted during the updating process. You can update a corrupted BIOS

leusingaUSBashdrivethatcontainstheupdatedBIOSle.

PrepareaUSBashdrivecontainingtheupdatedmotherboardBIOSbeforeusingthis

utility.

Recovering the BIOS from a USB flash drive

TorecovertheBIOSfromaUSBashdrive:

1. InserttheUSBashdrivewiththeoriginalorupdatedBIOSletooneUSBportonthe

system.

2. The utility will automatically recover the BIOS. It resets the system when the BIOS

recoverynished.

DO NOT shut down or reset the system while recovering the BIOS! Doing so would cause

system boot failure!

The recovered BIOS may not be the latest BIOS version for this motherboard. Visit the

ASUSwebsiteatwww.asus.comtodownloadthelatestBIOSle.

SaveacopyoftheoriginalmotherboardBIOSletoabootableUSBashdiskdrivein

case you need to restore the BIOS in the future. Copy the original motherboard BIOS using

the BUPDATER utility.

4-3

Z11PA-U12 Series

3. Press <Tab> to switch to the Driveeld.

4. PresstheUp/DownarrowkeystondtheUSBashdiskthatcontainsthelatestBIOS

then press <Enter>.

5. Press <Tab> to switch to the Folder Info eld.

6. PresstheUp/DownarrowkeystondtheBIOSlethenpress<Enter>.

7. Reboot the system when the update process is done.

4.1.2 ASUS EzFlash Utility

TheASUSEzFlashUtilityfeatureallowsyoutoupdatetheBIOSusingaUSBashdisk

without having to use a DOS-based utility.

The succeeding BIOS screens are for reference only. The actual BIOS screen displays

may not be the same as shown.

To update the BIOS using EzFlash Utility:

1. InserttheUSBashdiskthatcontainsthelatestBIOSletotheUSBport.

2. Enter the BIOS setup program. Go to the Tool menu to select Start EzFlash and press

<Enter> to enable it.

Download the latest BIOS from the ASUS website at www.asus.com before using this

utility.

ASUS Tek. EzFlash Utility

[Up/Down/Left/Right]:Switch [Enter]:Choose [q]:Exit

FS0 System Volume Information <DIR>

Windows <DIR>

Z11PA-U12-ASUS-0204 <DIR>

Current Platform

Platform : Z11PA-U12 Platform : Z11PA-U12

Version : 0106

Build Date :06/21/2017

New Platform

Version : 0204

Build Date :07/24/2017

4-4 Chapter 4: BIOS Setup

• ThisfunctioncansupportdevicessuchasaUSBashdiskwithFAT32/16formatand

single partition only.

• DONOTshutdownorresetthesystemwhileupdatingtheBIOStopreventsystem

boot failure!

4.1.3 BUPDATER utility

The succeeding BIOS screens are for reference only. The actual BIOS screen displays

may not be the same as shown.

TheBUPDATERutilityallowsyoutoupdatetheBIOSleinDOSenvironmentusinga

bootableUSBashdiskdrivewiththeupdatedBIOSle.

Updating the BIOS file

ToupdatetheBIOSleusingtheBUPDATERutility:

1. VisittheASUSwebsiteatwww.asus.comanddownloadthelatestBIOSleforthe

motherboard.SavetheBIOSletoabootableUSBashdiskdrive.

2. Download the BUPDATER utility (BUPDATER.exe) from the ASUS support website at

support.asus.comtothebootableUSBashdiskdriveyoucreatedearlier.

3. Boot the system in DOS mode, then at the prompt, type:

 BUPDATER/i[lename].CAP

where[lename]isthelatestortheoriginalBIOSleonthebootableUSBashdisk

drive, then press <Enter>.

A:\>BUPDATER /i[le name]CAP

Ensure to load the BIOS default settings to ensure system compatibility and stability. Press

<F5> and select Yes to load the BIOS default settings.

4-5

Z11PA-U12 Series

4. Theutilityveriesthele,thenstartsupdatingtheBIOSle.

DO NOT shut down or reset the system while updating the BIOS to prevent system boot

failure!

5. The utility returns to the DOS prompt after the BIOS update process is completed.

Rebootthesystemfromtheharddiskdrive.

The BIOS update is nished! Please restart your system.

C:\>

Current Platform

Platform : Z11PA-U12

Version : 0106

Build date: 06/21/2017

New Platform

Platform : Z11PA-U12

Version : 0204

Build date: 07/24/2017

ASUS Tek. EzFlash Utility

Start Programming Flash. DO NOT SHUTDOWN THE SYSTEM!!!

Write

75%

4-6 Chapter 4: BIOS Setup

4.2 BIOS setup program

Thismotherboardsupportsaprogrammablermwarechipthatyoucanupdateusingthe

provided utility described in section 4.1 Managing and updating your BIOS.

UsetheBIOSSetupprogramwhenyouareinstallingamotherboard,reconguringyour

system,orpromptedto“RunSetup.”Thissectionexplainshowtocongureyoursystem

using this utility.

EvenifyouarenotpromptedtousetheSetupprogram,youcanchangethecongurationof

your computer in the future. For example, you can enable the security password feature or

changethepowermanagementsettings.Thisrequiresyoutorecongureyoursystemusing

the BIOS Setup program so that the computer can recognize these changes and record them

intheCMOSRAMofthermwarechip.

ThermwarechiponthemotherboardstorestheSetuputility.Whenyoustartupthe

computer, the system provides you with the opportunity to run this program. Press <Del>

during the Power-On Self-Test (POST) to enter the Setup utility; otherwise, POST continues

with its test routines.

If you wish to enter Setup after POST, restart the system by pressing <Ctrl+Alt+Delete>, or by

pressing the reset button on the system chassis. You can also restart by turning the system

offandthenbackon.Dothislastoptiononlyifthersttwofailed.

TheSetupprogramisdesignedtomakeitaseasytouseaspossible.Beingamenu-driven

program,itletsyouscrollthroughthevarioussub-menusandmakeyourselectionsfromthe

availableoptionsusingthenavigationkeys.

• ThedefaultBIOSsettingsforthismotherboardapplyformostconditionstoensure

optimum performance. If the system becomes unstable after changing any BIOS

settings, load the default settings to ensure system compatibility and stability. Press

<F5> and select Yes to load the BIOS default settings.

• TheBIOSsetupscreensshowninthissectionareforreferencepurposesonly,and

may not exactly match what you see on your screen.

• VisittheASUSwebsite(www.asus.com)todownloadthelatestBIOSleforthis

motherboard.

4-7

Z11PA-U12 Series

4.2.1 BIOS menu screen

Navigation keys

General helpMenu bar Configuration fieldsMenu items

4.2.2 Menu bar

The menu bar on top of the screen has the following main items:

Main   Forchangingthebasicsystemconguration

Ai Tweaker Forchangingtheoverclockingsettings

Advanced For changing the advanced system settings

Platform Configuration For changing the platform settings

Socket Configuration Forchangingthesocketsettings

Event Logs For changing the event log settings

Server Mgmt For changing the server mgmt settings

Security For changing the security settings

Boot   Forchangingthesystembootconguration

Tool   Forconguringoptionsforspecialfunctions

Save & Exit For selecting the save & exit options

Toselectanitemonthemenubar,presstherightorleftarrowkeyonthekeyboarduntilthe

desired item is highlighted.

4-8 Chapter 4: BIOS Setup

4.2.3 Menu items

Thehighlighteditemonthemenubardisplaysthespecicitemsforthatmenu.Forexample,

selecting Main shows the Main menu items.

Theotheritems(Advanced,PlatformConguration,SocketConguration,EventLogs,Server

Mgmt, Security, Boot, Tool, and Save & Exit) on the menu bar have their respective menu

items.

4.2.4 Submenu items

A solid triangle before each item on any menu screen means that the item has a submenu.

To display the submenu, select the item then press <Enter>.

4.2.5 Navigation keys

AtthebottomrightcornerofamenuscreenarethenavigationkeysfortheBIOSsetup

program.Usethenavigationkeystoselectitemsinthemenuandchangethesettings.

4.2.6 General help

At the top right corner of the menu screen is a brief description of the selected item.

4.2.7 Configuration fields

Theseeldsshowthevaluesforthemenuitems.Ifanitemisuser-congurable,youcan

changethevalueoftheeldoppositetheitem.Youcannotselectanitemthatisnotuser-

congurable.

Acongurableeldisenclosedinbrackets,andishighlightedwhenselected.Tochangethe

valueofaeld,selectitandpress<Enter>todisplayalistofoptions.

4.2.8 Pop-up window

Selectamenuitemandpress<Enter>todisplayapop-upwindowwiththeconguration

options for that item.

4.2.9 Scroll bar

Ascrollbarappearsontherightsideofamenuscreenwhenthereareitemsthatdonotton

thescreen.PresstheUp/Downarrowkeysor<PageUp>/<PageDown>keystodisplaythe

other items on the screen.

4-9

Z11PA-U12 Series

4.3 Main menu

WhenyouentertheBIOSSetupprogram,theMainmenuscreenappears.TheMainmenu

provides you an overview of the basic system information, and allows you to set the system

date, time, language, and security settings.

4.3.1 System Date [Day xx/xx/xxxx]

Allows you to set the system date.

4.3.2 System Time [xx:xx:xx]

Allows you to set the system time.

4-10 Chapter 4: BIOS Setup

4.4 Advanced menu

The Advanced menu items allow you to change the settings for the CPU and other system

devices.

TakecautionwhenchangingthesettingsoftheAdvancedmenuitems.Incorrecteld

values can cause the system to malfunction.

4.4.1 Trusted Computing

Configuration

Security Device Support [Enabled]

Allows you to enable or disable the BIOS support for security device.

Congurationoptions:[Disabled][Enabled]

4-11

Z11PA-U12 Series

4.4.3 Smart Settings

SMART Self Test [Enabled]

Allows you to run SMART Self Test on all HDDs during POST.

Congurationoptions:[Disabled][Enabled]

4.4.2 ACPI Settings

Enable ACPI Auto Configuration [Disabled]

AllowsyoutoenableordisabletheBIOSACPIAutoConguration.

Congurationoptions:[Disabled][Enabled]

Enable Hibernation [Enabled]

Allows you to enable or disable the ability of the system to hibernate (OS/S4 Sleep State).

Congurationoptions:[Disabled][Enabled]

This option may be not be effective with some OS.

ACPI Sleep State [S3 (Suspend to RAM)]

Allows you to select the highest ACPI sleep state the system will enter when the SUSPEND

button is pressed.

Congurationoptions:[SuspendDisabled][S3(SuspendtoRAM)]

4-12 Chapter 4: BIOS Setup

4.4.4 Super IO Configuration

Serial Port 1 Configuration

Allows you to set the parameters of Serial Port 1.

Serial Port [Enabled]

Allows you to enable or disable Serial Port.

Congurationoptions:[Disabled][Enabled]

The following item appears only when you set Serial Port to [Enabled].

Change Settings [Auto]

Allows you to choose the setting for Super IO device.

Congurationoptions:[Auto][IO=3F8h;IRQ=4;][IO=3F8h;IRQ=3,4,5,6,7,9,10,11,

12;][IO=2F8h;IRQ=3,4,5,6,7,9,10,11,12;][IO=3E8h;IRQ=3,4,5,6,7,9,10,11,

12;][IO=2E8h;IRQ=3,4,5,6,7,9,10,11,12;]

4.4.5 Serial Port Console Redirection

COM1 / COM2

Console Redirection [Disabled]

Allows you to enable or disable the console redirection feature.

Congurationoptions:[Disabled][Enabled]

4-13

Z11PA-U12 Series

Console Redirection Settings

ThisitembecomescongurableonlywhenyouenabletheConsole Redirection item. The

settings specify how the host computer and the remote computer (which the user is using)

will exchange data. Both computers should have the same or compatible settings.

The following item appears only when you set Console Redirection to [Enabled].

Terminal Type [VT-UTF8]

Allows you to set the terminal type.

[VT100] ASCIIcharset.

[VT100+] ExtendsVT100tosupportcolor,functionkeys,etc.

[VT-UTF8] UsesUTF8encodingtomapUnicodecharsonto1ormorebytes.

[ANSI] ExtendedASCIIcharset.

Bits per second [57600]

Selects serial port transmission speed. The speed must be matched on the other side.

Longornoisylinesmayrequirelowerspeeds.

Congurationoptions:[9600][19200][38400][57600][115200]

Data Bits [8]

Congurationoptions:[7][8]

Parity [None]

Aparitybitcanbesentwiththedatabitstodetectsometransmissionerrors.[Mark]

and[Space]paritydonotallowforerrordetection.

[None] None.

[Even] paritybitis0ifthenumof1’sinthedatabitsiseven.

[Odd] paritybitis0ifnumof1’sinthedatabitsisodd.

[Mark] paritybitisalways1.

[Space] paritybitisalways0.

Stop Bits [1]

Stopbitsindicatetheendofaserialdatapacket.(Astartbitindicatesthebeginning.)

The standard setting is 1 stop bit. Communication with slow devices may require more

than 1 stop bit.

Congurationoptions:[1][2]

4-14 Chapter 4: BIOS Setup

Flow Control [Hardware RTS/CTS]

Flowcontrolcanpreventdatalossfrombufferoverow.Whensendingdata,ifthe

receivingbuffersarefull,a“stop”signalcanbesenttostopthedataow.Oncethe

buffersareempty,a“start”signalcanbesenttore-starttheow.Hardwareow

control uses two wires to send start/stop signals.

Congurationoptions:[None][HardwareRTS/CTS]

VT-UTF8 Combo Key Support [Enabled]

Allows you to enable the VT-UTF8 Combo Key Support for ANSI/VT100 terminals.

Congurationoptions:[Disabled][Enabled]

Recorder Mode [Disabled]

Withthismodeenabledonlytextwillbesent.ThisistocaptureTerminaldata.

Congurationoptions:[Disabled][Enabled]

Legacy OS Redirection Resolution [80x24]

ThisallowsyoutosetthenumberofrowsandcolumnssupportedontheLegacyOS.

Congurationoptions:[80x24][80x25]

Putty Keypad [VT100]

This allows you to select the FunctionKey and Keypad on Putty.

Congurationoptions:[VT100][LINUX][XTERMR6][SCO][ESCN][VT400]

Redirection After BIOS POST [Always Enable]

ThissettingallowsyoutospecifyifBootloaderisselectedthanLegacyconsole

redirection.

Congurationoptions:[AlwaysEnable][Bootloader]

Legacy Console Redirection Settings

Legacy Serial Redirection Port [COM1]

AllowsyoutoselectaCOMporttodisplayredirectionofLegacyOSandLegacy

OPROM Messages.

Congurationoptions:[COM1][COM2]

Serial Port for Out-of-Band Management/

Windows Emergency Management Services (EMS)

Console Redirection [Disabled]

Allows you to enable or disable the console redirection feature.

Congurationoptions:[Disabled][Enabled]

4-15

Z11PA-U12 Series

The following item appears only when you set Console Redirection to [Enabled].

Console Redirection Settings

Out-of-Band Mgmt Port [COM1]

MicrosoftWindowsEmergencyManagementServices(EMS)allowsforremote

managementofaWindowsServerOSthroughaserialport.

Congurationoptions:[COM1][COM2]

Terminal Type [VT-UTF8]

Allows you to set the terminal type for out-of-band management.

Congurationoptions:[VT100][VT100+][VT-UTF8][ANSI]

Bits per second [115200]

Allows you to set the serial port transmission speed.

Congurationoptions:[9600][19200][57600][115200]

Flow Control [None]

Allowsyoutosettheowcontroltopreventdatalossfrombufferoverow.

Congurationoptions:[None][HardwareRTS/CTS][SoftwareXon/Xoff]

4.4.6 Onboard LAN

Onboard I210 LAN Configuration

4-16 Chapter 4: BIOS Setup

Onboard X722 LAN Configuration

Intel LAN1 Enable [Enabled]

AllowsyoutoenableordisabletheIntelLAN.

Congurationoptions:[Disabled][Enabled]

The following item appears only when you set Intel LAN1 Enable to [Enabled].

Intel LAN ROM Type [PXE]

AllowsyoutoselecttheIntelLANROMtype.

Congurationoptions:[Disabled][PXE][iSCSI]

Due to Intel®limitations,bothIntelLANROMTypeoptionsshouldbethesamewhen[PXE]

or [iSCSI] is selected.

Intel LAN2 Enable [Enabled]

AllowsyoutoenableordisabletheIntelLAN.

Congurationoptions:[Disabled][Enabled]

The following item appears only when you set Intel LAN2 Enable to [Enabled].

Intel LAN ROM Type [Disabled]

AllowsyoutoselecttheIntelLANROMtype.

Congurationoptions:[Disabled][PXE][iSCSI]

Due to Intel®limitations,bothIntelLANROMTypeoptionsshouldbethesamewhen[PXE]

or [iSCSI] is selected.

Intel X722 LAN Enable [Enabled]

AllowsyoutoenableordisabletheIntelLAN.

Congurationoptions:[Disabled][Enabled]

4-17

Z11PA-U12 Series

4.4.7 APM

AllowsyoutoconguretheAdvancePowerManagement(APM)settings.

Restore AC Power Loss [Last State]

Whensetto[PowerOff],thesystemgoesintooffstateafteranACpowerloss.Whenset

to[PowerOn],thesystemwillrebootafteranACpowerloss.Whensetto[LastState],the

system goes into either off or on state, whatever the system state was before the AC power

loss.

Congurationoptions:[PowerOff][PowerOn][LastState]

Power On By PCIE [Disabled]

[Disabled] DisablesthePCIEdevicestogenerateawakeevent.

[Enabled] EnablesthePCIEdevicestogenerateawakeevent.

Power On By RTC [Disabled]

[Disabled] DisablesRTCtogenerateawakeevent.

[Enabled] Whensetto[Enabled],theitemsRTC Alarm Date (Days) and

Hour/Minute/Secondwillbecomeuser-congurablewithsetvalues.

4-18 Chapter 4: BIOS Setup

Load RT32 Image [Disabled]

AllowsyoutoenableordisableRT32ImageLoading.

Congurationoptions:[Disabled][Enabled]

Above 4G Decoding [Disabled]

Allows you to enable or disable 64-bit capable devices to be decoded in above 4G address

space.Itonlyworksifthesystemsupports64-bitPCIdecoding.

Congurationoptions:[Disabled][Enabled]

SR-IOV Support [Enabled]

This option enables or disables SIngle Root IO Virtualization Support if the system has

SRIOV capable PCIe devices.

Congurationoptions:[Disabled][Enabled]

PCI Express Settings

PCI Express Device Register Settings

Relaxed Ordering [Enabled]

This option allows you to enable or disable PCI Express Device Relaxed Ordering.

Congurationoptions:[Disabled][Enabled]

Extended Tag [Disabled]

ThisoptionallowsDevicetousean8-bitTageldasarequesterwhensettoEnabled.

Congurationoptions:[Disabled][Enabled]

No Snoop [Enabled]

This option allows you to enable or disable PCI Express Device No Snoop option.

Congurationoptions:[Disabled][Enabled]

Maximum Payload [Auto]

This option allows you to set the Maximum Payload of PCI Express Device or allow

System BIOS to select the value.

Congurationoptions:[Auto][128Bytes][256Bytes][512Bytes][1024Bytes]

[2048Bytes][4096Bytes]

4.4.8 PCI Subsystem Settings

AllowsyoutocongurePCI,PCI-X,andPCIExpressSettings.

4-19

Z11PA-U12 Series

Maximum Read Request [Auto]

This option allows you to set the Maximum Read Request of PCI Express Device or

allow System BIOS to select the value.

Congurationoptions:[Auto][128Bytes][256Bytes][512Bytes][1024Bytes]

[2048Bytes][4096Bytes]

PCI Express Device Link Register Settings

ASPM Support [Disabled]

This option allows you to set the ASPM level.

[ForceL0s] ForcealllinkstoL0sState.

[Auto] BIOSautocongure.

[Disabled] DisablesASPM.

Enabling ASPM may cause some PCI-E devices to fail.

Extended Synch [Disabled]

This option allows the generation of Extended Synchronization patterns when set to

Enabled.

Congurationoptions:[Disabled][Enabled]

Link Training Retry [5]

ThisoptionallowsyoutosetthenumberofRetryAttemptssoftwarewilltaketoretrain

thelinkifprevioustrainingattemptwasunsuccessful.

Congurationoptions:[Disabled][2][3][5]

Link Training Timeout [1000]

This option allows you to set the number of Microseconds software will wait before

polling‘LinkTraining’butinLinkStatusRegister.Thevaluerangesfrom10to10000

uS.

Unpopulated Links [Keep Link On]

ThisoptionwilldisableunpopulatedPCIExpresslinkstosavepowerwhensetto

Disabled.

Congurationoptions:[Disabled][KeepLinkOn]

PCI Express Gen 2 Settings

PCI Express GEN2 Device Register Settings

Completion Timeout [Default]

This option allows system software to modify the Completion Timeout value for device

Functions which support Completion Timeout programmability.

[Default] 50usto50ms.

[Shorter] Shortertimeoutrangessupportedbyhardwarewillbeused.

[Longer] Longertimeoutrangessupportedbyhardwarewillbeused.

[Disabled] DisableCompletionTimeout.

4-20 Chapter 4: BIOS Setup

ARI Forwarding [Disabled]

If supported by hardware and set to Enabled, the Downstream Port disables

itstraditionalDeviceNumberledbeing0enforcementwhenturningaType1

CongurationRequestintoaType0CongurationRequest,permittingaccessto

Extended Functions in an ARI Device immediately below the Port.

Congurationoptions:[Disabled][Enabled]

Atomic0p Request Enable [Disabled]

If supported by hardware and set to Enabled, this function initiates Atomic0p Requests

only if Bus Master Enable bit is in the Command Register Set.

Congurationoptions:[Disabled][Enabled]

Atomic0p Egress Blocking [Disabled]

If supported by hardware and set to Enabled, outbound Atomic0p Requests via Egress

Portswillbeblocked.

Congurationoptions:[Disabled][Enabled]

IDO Request Enable [Disabled]

If supported by hardware and set to Enabled, this permits setting the number of ID-

BasedOrdering(IDO)bit(Attribute[2])requeststobeinitiated.

Congurationoptions:[Disabled][Enabled]

IDO Completion Enable [Disabled]

If supported by hardware and set to Enabled, this permits setting the number of ID-

BasedOrdering(IDO)bit(Attribute[2])requeststobeinitiated.

Congurationoptions:[Disabled][Enabled]

LTR Mechanism Enable [Disabled]

If supported by hardware and set to Enabled,thisenablestheLatencyTolerance

Reporting(LTR)Mechanism.

Congurationoptions:[Disabled][Enabled]

IDO Request Enable [Disabled]

If supported by hardware and set to Enabled, this permits setting the number of ID-

BasedOrdering(IDO)bit(Attribute[2])requeststobeinititated.

Congurationoptions:[Disabled][Enabled]

End-End TLP Prefix Blocking [Disabled]

If supported by hardware and set to Enabled,thisfunctionwillblockforwardingof

TLPscontainingEnd-EndTLPPrexes.

Congurationoptions:[Disabled][Enabled]

PCI Express GEN2 Device Register Settings

Target Link Speed [Auto]

If supported by hardware and set to Force to X.X GT/s, for Downstream Ports, this

setsanupperlimitonLinkoperationalspeedbyrestrictingthevaluesadvertisedbythe

Upstreamcomponentinitstrainingsequences.WhenAutoisselectedHWinitialized

data will be used.

Congurationoptions:[Auto][Forceto2.5GT/s][Forceto5.0GT/s][Forceto8.0GT/s]

4-21

Z11PA-U12 Series

Clock Power Management [Disabled]

If supported by hardware and set to Enabled,thedeviceispermittedtouseCLKREQ#

signalforpowermanagementofLinkclockinaccordancetoprotocoldenedin

appropriateformfactorspecication.

Congurationoptions:[Disabled][Enabled]

Compliance SOS [Disabled]

If supported by hardware and set to Enabled,thiswillforceLTSSMtosendSKP

OrderedSetsbetweensequenceswhensendingCompliancePatternorModied

Compliance Pattern.

Congurationoptions:[Disabled][Enabled]

Hardware Autonomous Width [Enabled]

If supported by hardware and set to Disabled,thiswilldisablethehardware’sabilityto

changelinkwidthexceptforwidthsizereductionforthepurposeofcorrectingunstable

linkoperation.

Congurationoptions:[Disabled][Enabled]

Hardware Autonomous Speed [Enabled]

If supported by hardware and set to Disabled,thiswilldisablethehardware’sability

tochangelinkspeedexceptforspeedratereductionforthepurposeofcorrecting

unstablelinkoperation.

Congurationoptions:[Disabled][Enabled]

PCIE OPROM Slot Options

PCIE1-6 Slot OPROM [Enabled]

This option allows you to enable or disable the OPROM of the PCIe slots.

Congurationoptions:[Disabled][Enabled]

4-22 Chapter 4: BIOS Setup

4.4.9 Network Stack Configuration

Allowsyoutocongurethenetwordstackconguration.

Network Stack [Disabled]

AllowsyoutoenableordisableUEFINetworkStack.

Congurationoptions:[Disabled][Enabled]

The following items appear only when you set the Network Stack to [Enabled].

Ipv4 PXE Support [Disabled]

EnablesordisablestheIpv4PXEBootSupport.Ifdisabled,Ipv4PXEbootoptionwill

not be created.

Congurationoptions:[Disable][Enable]

Ipv4 HTTP Support [Disabled]

EnablesordisablestheIpv4HTTPBootSupport.Ifdisabled,Ipv4PXEbootoptionwill

not be created.

Congurationoptions:[Disable][Enable]

Ipv6 PXE Support [Disabled]

EnablesordisablestheIpv6PXEBootSupport.Ifdisabled,Ipv6PXEbootoptionwill

not be created.

Congurationoptions:[Disable][Enable]

Ipv6 HTTP Support [Disabled]

EnablesordisablestheIpv6HTTPBootSupport.Ifdisabled,Ipv6PXEbootoptionwill

not be created.

Congurationoptions:[Disable][Enable]

PXE boot wait time [0]

SetthewaittimetopressESCkeytoabortthePXEboot.Usethe<+>or<->toadjust

the value. The values range from 0 to 5.

Media detect count [1]

Setthenumberoftimespresenceofmediawillbechecked.Usethe<+>or<->to

adjustthevalue.Thevaluesrangefrom1to50.

4-23

Z11PA-U12 Series

4.4.10 CSM Configuration

CSM Support [Enabled]

This option allows you to enable or disable CSM Support.

Congurationoptions:[Disabled][Enabled]

The following items appear only when you set the CSM Support to [Enabled].

GateA20 Active [Upon Request]

This allows you to set the GA20 option.

[UponRequest] GA20canbedisabledusingBIOSservices.

[Always] DonotallowdisablingGA20;thisoptionisusefulwhenanyRT

code is executed above 1MB.

Option ROM Messages [Force BIOS]

This allows you to set the display mode for option ROM.

Congurationoptions:[ForceBIOS][KeepCurrent]

INT19 Trap Response [Immediate]

This option allows you to control the BIOS reaction on INT19 trapping by Option ROM.

[Immediate] Executethetraprightaway.

[Legacyonly] Executethetrapduringlegacyboot.

Boot Option filter [Legacy only]

ThisoptionallowsyoutocontroltheLegacy/UEFIROMspriority.

Congurationoptions:[UEFIandLegacy][Legacyonly][UEFIonly]

Network / Storage / Video [Legacy]

ThisoptionallowsyoutocontroltheexecutionofUEFIandLegacyPXE/Storage/

Video OpROM.

Congurationoptions:[UEFI][Legacy]

Other PCI devices [Legacy]

ThisitemdeterminestheOpROMexecutionpolicyfordevicesotherthanNetwork,

Storage, or Video.

Congurationoptions:[UEFI][Legacy]

4-24 Chapter 4: BIOS Setup

4.4.12 USB Configuration

Legacy USB Support [Enabled]

[Disabled] TheUSBdevicescanbeusedonlyfortheBIOSsetupprogram.Itcannot

be recognized in boot devices list.

[Enabled] EnablesthesupportforUSBdevicesonlegacyoperatingsystems(OS).

[Auto] AllowsthesystemtodetectthepresenceofUSBdevicesatstartup.If

detected, the USB controller legacy mode is enabled. If no USB device is

detected, the legacy USB support is disabled.

USB Mass Storage Driver Support [Enabled]

Allows you to enable or disable the USB Mass Storage driver support.

Congurationoptions:[Disabled][Enabled]

Mass Storage Devices

Allows you to select the mass storage device emulation type for devices connected.

Congurationoptions:[Auto][Floppy][ForcedFDD][HardDisk][CD-ROM]

4.4.11 NVMe Configuration

You may view the NVMe controller and Drive information if an NVMe device is connected.

4-25

Z11PA-U12 Series

4.4.13 iSCSI Configuration

AllowsyoutoconguretheiSCSiparameters.

4.4.14 Intel(R) Virtual RAID on CPU

AllowsyoutoconguretheviewtheRAIDvolumesandVMDcontrollersonthesystem.

4-26 Chapter 4: BIOS Setup

PCH Devices

Board Capability [DeepSx]

[SUS_PWR_DN_ACK] Send.

[DeepSx]  ShowDeepSxPolicies.

DeepSx Power Policies [Disabled]

AllowsyoutoconguretheDeepSxModeconguration.

Congurationoptions:[Disabled][EnabledinS5][EnabledinS4andS5]

GP27 Wake From DeepSx [Disabled]

AllowsyoutoenableordisableGP27WakeFromDeepSx.

Congurationoptions:[Disabled][Enabled]

PCI Express Configuration

PCI-E ASPM Support (Global) [L1 Only]

Allows you to select ASPM support for all downstream devices.

Congurationoptions:[Perindividualport][L1Only]

PCH DMI ASPM [Platform-POR]

AllowsyoutocongurethePCHDMIASPM.

Congurationoptions:[Platform-POR][ASPML1][Disabled]

4.5.1 PCH Configuration

4.5 Platform Configuration menu

The IntelRCSetup menu items allow you to change the platform settings.

TakecautionwhenchangingthesettingsofthePlatformCongurationmenuitems.

Incorrecteldvaluescancausethesystemtomalfunction.

4-27

Z11PA-U12 Series

PCH SATA Configuration

SATA Controller [Enabled]

Allows you to enable or disable the SATA Controller.

Congurationoptions:[Disabled][Enabled]

The following item appears only when you set SATA Controller to [Enabled].

Configure SATA as [AHCI]

AllowsyoutoidentifytheSATAportconnectedtoSolidStateDriveorHardDiskDrive.

Congurationoptions:[AHCI][RAID]

Support Aggressive Link Power Management [Enabled]

AllowsyoutoenableordisabletheSupportAggressiveLinkPower(SALP)

Management.

Congurationoptions:[Disabled][Enabled]

SATA Port 0-7

Port 0-7

Allows you to enable or disable the SATA port.

Congurationoptions:[Disabled][Enabled]

PCH sSATA Configuration

sSATA Controller [Enabled]

Allows you to enable or disable the sSATA Controller.

Congurationoptions:[Disabled][Enabled]

The following item appears only when you set sSATA Controller to [Enabled].

Configure sSATA as [AHCI]

AllowsyoutoidentifytheSATAportconnectedtoSolidStateDriveorHardDiskDrive.

Congurationoptions:[AHCI][RAID]

Support Aggressive Link Power Management [Enabled]

AllowsyoutoenableordisabletheSupportAggressiveLinkPower(SALP)

Management.

Congurationoptions:[Disabled][Enabled]

sSATA Port 0-5

Port 0-5

Allows you to enable or disable the SATA port.

Congurationoptions:[Disabled][Enabled]

USB Configuration

USB Precondition [Disabled]

AllowsyoutoenableordisablepreconditionworkonUSBhostcontrollerandroot

ports for faster enumeration.

Congurationoptions:[Disabled][Enabled]

4-28 Chapter 4: BIOS Setup

XHCI Manual Mode [Disabled]

This option is used by validation.

Congurationoptions:[Disabled][Enabled]

The following items appear only when the XHCI Manual Mode is set to [Enabled].

Trunk Clock Gating (BTCG) [Enabled]

Allows you to enable or disable BTCG.

Congurationoptions:[Disabled][Enabled]

Enable USB 3.0 pins [Disable all pins]

Allows you to enable or disable USB 3.0 pins or on a per pin basis.

Congurationoptions:[SelectPer-Pin][Disableallpins][Enableallpins]

USB Per-Connector Disable [Disabled]

Allows you to enable or disable each of the USB physical connectors. Once a

connector is disabled, any USB devices plugged into the connector will not be detected

by BIOS or OS.

Congurationoptions:[Disabled][Enabled]

The following items appear only when the USB Per-Connector Disable is set to

[Enabled].

USB HS Physical Connector #0-13 Disable [Enabled]

Congurationoptions:[Disabled][Enabled]

USB SS Physical Connector #0-9 Disable [Enabled]

Congurationoptions:[Disabled][Enabled]

Security Configuration

SMM BIOS Write Protect [Enabled]

AllowsyoutoenableordisableSMMBIOSWriteProtect.

Congurationoptions:[Disabled][Enabled]

DCI Auto Detect Enable [Disabled]

Whenenabled,itdetectsDCIbeingconnectedduringBIOSPOSTtimeandenablesDCI.

Congurationoptions:[Disabled][Enabled]

4-29

Z11PA-U12 Series

4.5.2 Miscellaneous Configuration

Active Video [Offboard Device]

Allows you to select the video type.

Congurationoptions:[OnboardDevice][OffboardDevice]

PMTT ACPI Table [Disabled]

Allows you to enable or disable PMTT ACPI Table for DDR4 only.

Congurationoptions:[Disabled][Enabled]

4.5.3 Server ME Configuration

Displays the Server ME Technology parameters on your system.

Toquicklygotothelastitemofthesecondpage,pressthe Page Down button. Press the

Page Upbuttontogobacktotherstitemintherstpage.

Navigate to the second page of the screen to see the rest of items in this menu by pressing

theUporDownarrowkeys.

4-30 Chapter 4: BIOS Setup

4.5.4 Runtime Error Logging

Displays the Server ME Technology parameters on your system.

System Errors [Enabled]

This item allows you to enable or disable System Errors.

Congurationoptions:[Disabled][Enabled]

Whea Settings

Whea Support [Enabled]

ThisitemallowsyoutoenableordisabletheWHEAsupport.

Congurationoptions:[Disabled][Enabled]

4-31

Z11PA-U12 Series

4.6 Socket Configuration menu

TheIntelRCSetupmenuitemsallowyoutochangethesocketsettings.

4.6.1 Processor Configuration

Toquicklygotothelastitemofthesecondpage,pressthe Page Down button. Press the

Page Upbuttontogobacktotherstitemintherstpage.

Navigate to the second page of the screen to see the rest of items in this menu by pressing

theUporDownarrowkeys.

Hyper-threading [ALL] [Enabled]

This item allows a hyper-threading processor to appear as two logical processors, allowing

the operating system to schedule two threads or processors simultaneously.

Congurationoptions:[Disabled][Enabled]

4-32 Chapter 4: BIOS Setup

Execute Disable Bit [Enabled]

XDcanpreventcertainclassesofmaliciousbufferoverowattackswhencombinedwith

asupportingOS(WindowsServer2003SP1,WindowsXPSP2,SuSELinux9.2,Redhat

Enterprise 3 Update 3).

Congurationoptions:[Disabled][Enabled]

Enable Intel(R) TXT [Disabled]

ForcestheXDfeaturelogtoalwaysreturn0whendisabled.

Congurationoptions:[Disabled][Enabled]

VMX [Enabled]

EnablestheVanderpoolTechnology.Takeseffectafterreboot.

Congurationoptions:[Disabled][Enabled]

Enable SMX [Disabled]

Enables the Safer Mode Extensions.

Congurationoptions:[Disabled][Enabled]

Hardware Prefetcher [Enabled]

ThisItemallowsyoutoturnon/offthemidlevelcache(L2)streamerprefetcher.

Congurationoptions:[Disabled][Enabled]

Adjacent Cache Prefetch [Enabled]

ThisItemallowsyoutoturnon/offprefetchingofadjacentcachelines.

Congurationoptions:[Disabled][Enabled]

DCU Streamer Prefetcher [Enabled]

ThisItemallowsyoutoenableordisableprefetcherofnextL1dataline.

Congurationoptions:[Disabled][Enabled]

DCU IP Prefetcher [Enabled]

ThisItemallowsyoutoenableordisableprefetchofnextL1linebaseduponsequentialload

history.

Congurationoptions:[Disabled][Enabled]

LLC Prefetch [Disabled]

ThisItemallowsyoutoenableordisableLLCPrefetchonallthreads.

Congurationoptions:[Disabled][Enabled]

DCU Mode [32KB 8Way Without ECC]

Congurationoptions:[32KB8WayWithoutECC][16KB4WayWithECC]

Extended APIC [Disabled]

This Item allows you to enable or disable the extended APIC support.

Congurationoptions:[Disabled][Enabled]

AES-NI [Enabled]

This Item allows you to enable or disable the AES-NI support.

Congurationoptions:[Disabled][Enabled]

4-33

Z11PA-U12 Series

4.6.2 Common RefCode Configuration

Numa [Enabled]

This item enables or disables the Non uniform Memory Access (NUMA).

Congurationoptions:[Disabled][Enabled]

4.6.3 UPI Configuration

UPI General Configuration

UPI Status

This item displays information about the UPI status.

Link Speed Mode [Fast]

ThisitemallowsyoutoselecttheUPIlinkspeedaseitherthefastmodeorslowmode.

Congurationoptions:[Slow][Fast]

Link Frequency Select [Auto]

ThisitemallowsforselectingtheUPIlinkfrequency.

Congurationoptions:[Auto][9.6GB/s][10.4GB/s][UsePerLinkSetting]

Link0p Enable [Auto]

Congurationoptions:[Disabled][Enabled][Auto]

Link1 Enable [Auto]

Congurationoptions:[Disabled][Enabled][Auto]

Stale AtoS [Disabled]

Congurationoptions:[Disabled][Enabled][Auto]

LLC dead line alloc [Enabled]

Congurationoptions:[Disabled][Enabled][Auto]

4-34 Chapter 4: BIOS Setup

4.6.4 Memory Configuration

Enforce POR [Auto]

Allows you to enforce POR restrictions for DDR4 frequency and voltage programming.

Congurationoptions:[Auto][POR][Disabled]

Memory Frequency [Auto]

Allows you to select the memory frequency setting.

Congurationoptions:[Auto][2133][2400][2666]

Data Scrambling for DDR4 [Auto]

Allows you to enable or disable data scrambling.

Congurationoptions:[Auto][Disabled][Enabled]

Memory Topology

Displays memory topology with DIMM population information.

Page Policy

AllowsyoutocongurePagePolicysettings.

Page Policy [Auto]

Congurationoptions:[Auto][Closed][Adaptive]

Memory Map

IMC Interleaving [Auto]

Select different IMC interleaving setting.

Congurationoptions:[Auto][1-wayInterleave][2-wayInterleave]

Channel Interleaving [Auto]

Select different channel interleaving setting.

Congurationoptions:[Auto][1-wayInterleave][2-wayInterleave]

[3-wayInterleave]

Rank Interleaving [Auto]

Selectdifferentrankinterleavingsetting.

Congurationoptions:[Auto][1-wayInterleave][2-wayInterleave]

[4-wayInterleave][8-wayInterleave]

4-35

Z11PA-U12 Series

4.6.5 IIO Configuration

Memory RAS Configuration

Mirror mode [Disabled]

AllowsyoutoselectMirrormodes.Mirrormodewillsetentire1LM/2LMmemoryin

system to be mirrored, consequently reducing the memory capacity by half. Enabling

MirrormodewilldisableXPTPrefetch.

Congurationoptions:[Disabled][MirrorMode1LM][MirrorMode2LM]

Mirror TAD0 [Disabled]

Allows you to enable or disable Mirror on entire memory for TAD0.

Congurationoptions:[Disabled][Enabled]

Enable Partial Mirror [Disabled]

Partialmirrormodewillenabletherequiredsizeofmemorytobemirrored.Ifrank

sparingisenabled,partialmirroringwillnottakeeffect.MirrorEnablewilldisableXPT

Prefetch.

Congurationoptions:[Disabled][Enabled]

UEFI ARM Mirror [Disabled]

Allows you to enable or disable UEFI ARM Mirror.

Congurationoptions:[Disabled][Enabled]

Memory Rank Sparing [Disabled]

AllowsyoutoenableordisableMemoryRankSparing

Congurationoptions:[Disabled][Enabled]

Patrol Scrub [Enabled]

Allows you to enable or disable Patrol Scrub.

Congurationoptions:[Disabled][Enabled]

Socket1 Configuration

This option allows you to change the settings related to the PCI Express Ports.

4-36 Chapter 4: BIOS Setup

Intel® VT for Directed I/O (VT-d)

Intel® VT for Directed I/O (VT-d) [Enabled]

Allows you to enable or disable the Intel Virtualization Technology for Directed I/O.

Congurationoptions:[Disabled][Enabled]

IIO-PCIE Express Global Options

PCIE relaxed Ordering [Enabled]

Allows you to enable or disable PCIE relaxed Ordering.

Congurationoptions:[Disabled][Enabled]

4.6.6 Advanced Power Management Configuration

CPU P State Control

Boot performance mode [Max Performance]

Allows you to switch between Boot performance mode.

Congurationoptions:[MaxPerformance][MaxEfcient][SetbyIntelNodeManager]

Energy Efficient Turbo [Enabled]

AllowsyoutoenableordisableEnergyEfcientTurbo.

Congurationoptions:[Disabled][Enabled]

Turbo Mode [Enabled]

Allows you to enable or disable Turbo Mode.

Congurationoptions:[Disabled][Enabled]

Hardware PM State Control

Hardware P-States [Native Mode]

Allows you to switch between Hardware P-States mode.

Congurationoptions:[Disabled][NativeMode][OutofBandMode]

[NativeModewithnoLegacySupport]

CPU C State Control

Autonomous Core C-State [Disabled]

Allows you to enable or disable Autonomous Core C-State Report.

Congurationoptions:[Disabled][Enabled]

CPU C6 Report [Auto]

Allows you to select CPU C6 Report.

Congurationoptions:[Disabled][Enabled][Auto]

4-37

Z11PA-U12 Series

OS ACPI Cx [ACPI C2]

Allows you to select OS ACPI Cx Report.

Congurationoptions:[ACPIC2][ACPIC3]

Package C State Control

Package C State [Auto]

AllowsyoutoselectPackageCState.

Congurationoptions:[C0/C1state][C2state][C6(nonRetentionstate)]

[C6(Retentionstate)][NoLimit][Auto]

CPU Thermal Control

CPU T State Control

Software Controlled T-States [Disabled]

Allows you to enable or disable Software Controlled T-States.

Congurationoptions:[Disabled][Enabled]

CPU - Advanced PM Tuning

Energy Perf BIAS

Power Performance Tuning

Congurationoptions:[OSControlsEPB][BIOSControlsEPB]

The following item appears only when you set Power Performance Tuning to

[OS Controls EPB].

PECI PCS EPB

This option controls whether PECI has control over EPB.

Congurationoptions:[OSControlsEPB][PECIControlsEPBusingPCS]

The following item appears only when you set Power Performance Tuning to

[BIOS Controls EPB].

ENERGY_PERF_BIAS_CFG Mode

Congurationoptions:[Performance][BalancedPerformance][BalancedPower]

[Power]

Dynamic Loadline Switch

Congurationoptions:[Disabled][Enabled]

Workload Configuration

Thisoptionallowsoptimizationfortheworkloadcharacterization.

Congurationoptions:[UMA][NUMA]

4-38 Chapter 4: BIOS Setup

Averaging Time Window

This option is used to control the effective window of the average C0 an P0 time.

Congurationoptions:[0]-[99]

P0 TotalTimeThreshold Low

TheHWswitchingmechanismDISABLEStheperformancesetting(0)whenthetotal

P0 time is less than the threshold set.

Congurationoptions:[0]-[99]

P0 TotalTimeThreshold High

TheHWswitchingmechanismEnablestheperformancesetting(0)whenthetotalP0

time is greater than the threshold set.

Congurationoptions:[0]-[99]

4-39

Z11PA-U12 Series

Enabling/Disabling Options

Smbios Event Log [Enabled]

ChangethistoenableordisableallfeaturesofSmbiosEventLoggingduringboot.

Congurationoptions:[Disabled][Enabled]

Erasing Settings

Erase Event Log [No]

ChooseoptionsforerasingSmbiosEventLog.Erasingisdonepriortoanyloggingactivation

during reset.

Congurationoptions:[No][Yes,Nextreset][Yes,Everyreset]

4.7.2 View Smbios Event Log

Press <Enter> to view all smbios event logs.

4.7 Event Logs menu

4.7.1 Change Smbios Event Log Settings

Press<Enter>tochangetheSmbiosEventLogconguration.

Allvalueschangedheredonottakeeffectuntilcomputerisrestarted.

4-40 Chapter 4: BIOS Setup

4.8 Server Mgmt menu

OS Watchdog Timer [Disabled]

This item allows you to start a BIOS timer which can only be shut off by Intel Management

Software after the OS loads.

Congurationoptions:[Disabled][Enabled]

ThefollowingitemsarecongurableonlywhentheOS Watchdog Timer is set to [Enabled].

OS Wtd Timer Timeout [10 minutes]

AllowsyoutocongurethelengthfortheOSBootWatchdogTimer.

Congurationoptions:[5minutes][10minutes][15minutes][20minutes]

OS Wtd Timer Policy [Reset]

ThisitemallowsyoutocongurethehowthesystemshouldrespondiftheOSBoot

WatchTimerexpires.

Congurationoptions:[DoNothing][Reset][PowerDown]

4.8.1 System Event Log

AllowsyoutochangetheSELeventlogconguration.

Allvalueschangedheredonottakeeffectuntilcomputerisrestarted.

Erase SEL [No]

AllowsyoutochooseoptionsforerasingSEL.

Congurationoptions:[No][Yes,Onnextreset][Yes,Oneveryreset]

When SEL is Full [Do Nothing]

AllowsyoutochooseoptionsforreactionstoafullSEL.

Congurationoptions:[DoNothing][EraseImmediately]

4-41

Z11PA-U12 Series

4.8.2 BMC network configuration

Thesub-itemsinthiscongurationallowyoutoconguretheBMCnetworkparameters.

IPV4

DM_LAN1/ Shared LAN

Config Address source [Previous State]

ThisitemallowsyoutocongureLANchannelparametersstatisticallyordynamically(by

BIOSorBMC).UnspeciedoptionwillnotmodifyanyBMCnetworkparametersduringBIOS

phase.

Congurationoptions:[PreviousState][Static][DynamicBmcDhcp][DynamicBmcNonDhcp]

IPV6

DM_LAN1/ Shared LAN

IPV6 Support [Enabled]

AllowsyoutoenableordisableLAN1IPV6Support.

Congurationoptions:[Disabled][Enabled]

Toquicklygotothelastitemofthesecondpage,pressthe Page Down button. Press the

Page Upbuttontogobacktotherstitemintherstpage.

Navigate to the second page of the screen to see the rest of items in this menu by pressing

theUporDownarrowkeys.

4-42 Chapter 4: BIOS Setup

4.8.3 View System Event Log

This item allows you to view the system event log records.

Config Address source [Previous State]

ThisitemallowsyoutocongureLANchannelparametersstatisticallyordynamically(by

BIOSorBMC).UnspeciedoptionwillnotmodifyanyBMCnetworkparametersduringBIOS

phase.

Congurationoptions:[PreviousState][Static][DynamicBmcDhcp][DynamicBmcNonDhcp]

4-43

Z11PA-U12 Series

4.9 Security menu

This menu allows a new password to be created or a current password to be changed. The

menualsoenablesordisablestheSecureBootstateandletstheuserconguretheSystem

Mode state.

Administrator Password

To set an administrator password:

1. Select the Administrator Password item and press <Enter>.

2.FromtheCreateNewPasswordbox,keyinapassword,thenpress<Enter>.

3.Conrmthepasswordwhenprompted.

To change an administrator password:

1. Select the Administrator Password item and press <Enter>.

2.FromtheEnterCurrentPasswordbox,keyinthecurrentpassword,thenpress<Enter>.

3.FromtheCreateNewPasswordbox,keyinanewpassword,thenpress<Enter>.

4.Conrmthepasswordwhenprompted.

To clear the administrator password, follow the same steps as in changing an administrator

password,butpress<Enter>whenpromptedtocreate/conrmthepassword.

4-44 Chapter 4: BIOS Setup

User Password

To set a user password:

1. Select the User Password item and press <Enter>.

2.FromtheCreateNewPasswordbox,keyinapassword,thenpress<Enter>.

3.Conrmthepasswordwhenprompted.

To change a user password:

1. Select the User Password item and press <Enter>.

2.FromtheEnterCurrentPasswordbox,keyinthecurrentpassword,thenpress<Enter>.

3.FromtheCreateNewPasswordbox,keyinanewpassword,thenpress<Enter>.

4.Conrmthepasswordwhenprompted.

To clear a user password:

1. Select the Clear User Password item and press <Enter>.

2.SelectYesfromtheWarningmessagewindowthenpress<Enter>.

Secure Boot

This item allows you to customize the Secure Boot settings.

Attempt Secure Boot [Disabled]

Secure Boot can be enabled if the system is running in User mode with enrolled platform Key

(EPK) or if the CSM function is disabled.

Congurationoptions:[Disabled][Enabled]

Secure Boot Mode [Custom]

Allows you to set the Secure Boot selector.

Congurationoptions:[Custom][Standard]

4-45

Z11PA-U12 Series

Key Management

ThisitemonlyappearswhentheitemSecureBootModeissetto[Custom].TheKey

Management item allows you to modify Secure Boot variables and set Key Management

page.

Provision Factory Defaults [Disabled]

AllowsyoutoprovisionfactorydefaultSecureBootkeyswhenthesystemisinSetup

Mode.

Congurationoptions:[Disabled][Enabled]

Install Factory Default keys

ThisitemwillinstallallFactoryDefaultkeys.

Reset to Setup Mode

ThisitemappearsonlywhenyouloadthedefaultSecureBootkeys.Thisitemallows

youtoclearalldefaultSecureBootkeys.

Enroll Efi Image

This item will allow the image to run in Secure Boot mode.

Save All Secure Boot Variables

Thisitemwillaskyouifyouwanttosaveallsecurebootvariables.SelectYesifyou

want to save all secure boot variables, otherwise select No.

Platform Key (PK)

Congurationoptions:[SavetoFile][SetNew][Erase]

Key Exchange Keys / Authorized Signatures / Forbidden Signatures

Congurationoptions:[SavetoFile][SetNew][Append][Erase]

Authorized TimeStamps

Congurationoptions:[SetNew][Append]

OsRecovery Signatures

Congurationoptions:[SetNew][Append]

4-46 Chapter 4: BIOS Setup

4.10 Boot menu

The Boot menu items allow you to change the system boot options.

Bootup NumLock State [On]

Allowsyoutoselectthepower-onstatefortheNumLock.

Congurationoptions:[Off][On]

Boot Logo Display [Disabled]

Allows you to enable or disable the full screen logo display feature.

Congurationoptions:[Auto][FullScreen][Disabled]

The following item appears only when you set the Boot Logo Display to [Disabled].

POST Report [5 sec]

Allows you to set the desired POST Report waiting time from 1 to 10 seconds.

Congurationoptions:[1sec]~[10sec][UntilPressESC]

Boot Option Priorities

These items specify the boot device priority sequence from the available devices. The

number of device items that appears on the screen depends on the number of devices

installed in the system.

• Toselectthebootdeviceduringsystemstartup,press<F8>whenASUSLogo

appears.

• ToaccessWindowsOSinSafeMode,pleasepress<F8>afterPOST.

Network Device BBS Priorities

Thisitemallowsyoutosetthebootingfromnetwork.

Hard Drive / Floppy Drive BBS Priorities

These items appear only when you connect SATA ODD or hard drive to the SATA ports and

allow you to set the booting order of the SATA devices.

4-47

Z11PA-U12 Series

4.11 Tool menu

TheToolmenuitemsallowyoutocongureoptionsforspecialfunctions.Selectanitemthen

press <Enter> to display the submenu.

IPMI HWM

Allows you to run the IPMI hardware monitor.

Start EzFlash

Allows you to run ASUS EzFlash BIOS ROM Utility when you press <Enter>. Refer to the

ASUS EzFlash Utility section for details.

4.12 Save & Exit menu

The Exit menu items allow you to save or discard your changes to the BIOS items.

Discard Changes and Exit

Exit System setup without saving any changes.

Save Changes and Reset

Exit System setup after saving the changes.

Restore Defaults

Restore/load default values for all the setup options.

Pressing <Esc> does not immediately exit this menu. Select one of the options from this

menu or <F10> from the legend bar to exit.

4-48 Chapter 4: BIOS Setup

Boot Override

These items displays the available devices. The device items that appears on the screen

dependsonthenumberofdevicesinstalledinthesystem.Clickanitemtostartbootingfrom

the selected device.

Launch EFI Shell from filesystem device

ThisitemallowsyoutoattempttolaunchtheEFIShellapplication(shellx64.e)fromoneof

theavailablelesystemdevices.

RAID Conguration

This chapter provides instructions for setting up, creating,

and conguring RAID sets using the available utilities.

Chapter 5: RAID Conguration

5-2 Chapter 5: RAID Conguration

If you want to boot the system from a hard disk drive included in a created RAID set, copy

rst the RAID driver from the support DVD to a oppy disk before you install an operating

system to the selected hard disk drive.

5.1 RAID configurations

The motherboard supports Intel® Rapid Storage Technology enterprise Option ROM Utility

with RAID 0, RAID 1, RAID 10, and RAID 5 support.

If you want to install a Windows® operating system to a hard disk drive included in a RAID

set, you have to create a RAID driver disk and load the RAID driver during OS installation.

Refer to section 6.1 RAID driver installation for details.

5.1.1 RAID definitions

RAID 0 (Data striping) optimizes two identical hard disk drives to read and write data in

parallel, interleaved stacks. Two hard disks perform the same work as a single drive but at a

sustained data transfer rate, double that of a single disk alone, thus improving data access

and storage. Use of two new identical hard disk drives is required for this setup.

RAID 1 (Data mirroring) copies and maintains an identical image of data from one drive to

a second drive. If one drive fails, the disk array management software directs all applications

to the surviving drive as it contains a complete copy of the data in the other drive. This RAID

conguration provides data protection and increases fault tolerance to the entire system. Use

two new drives or use an existing drive and a new drive for this setup. The new drive must be

of the same size or larger than the existing drive.

RAID 5 stripes both data and parity information across three or more hard disk drives. Among

the advantages of RAID 5 conguration include better HDD performance, fault tolerance, and

higher storage capacity. The RAID 5 conguration is best suited for transaction processing,

relational database applications, enterprise resource planning, and other business systems.

Use a minimum of three identical hard disk drives for this setup.

RAID 10 is data striping and data mirroring combined without parity (redundancy data) having

to be calculated and written. With the RAID 10 conguration you get all the benets of both

RAID 0 and RAID 1 congurations. Use four new hard disk drives or use an existing drive

and three new drives for this setup.

5-3

Z11PA-U12 Series

5.1.2 Installing Serial ATA hard disks

The motherboard supports Serial ATA hard disk drives. For optimal performance, install

identical drives of the same model and capacity when creating a disk array.

To install the SATA hard disks for a RAID conguration:

1. Install the SATA hard disks into the drive bays.

2. Connect the SATA signal cables.

3. Connect a SATA power cable to the power connector on each drive.

5.1.3 Setting the RAID item in BIOS

You must set the RAID item in the BIOS Setup before you can create a RAID set from SATA

hard disk drives attached to the SATA connectors supported by Intel® C620 chipset.

To do this:

1. Enter the BIOS Setup during POST.

2. Go to the Platform Configuration menu > PCH Configuration menu > PCH SATA

Configuration, then press <Enter>.

3. Set Configure SATA as to [RAID Mode].

4. Press <F10> to save your changes and exit the BIOS Setup.

Refer to Chapter 4 for details on entering and navigating through the BIOS Setup.

5.1.4 RAID configuration utilities

Depending on the RAID connectors that you use, you can create a RAID set using the utilities

embedded in each RAID controller. For example, use the Intel® Rapid Storage Technology

if you installed Serial ATA hard disk drives on the Serial ATA connectors supported by the

Intel® C620 chipset.

Refer to the succeeding section for details on how to use the RAID conguration utility.

5-4 Chapter 5: RAID Conguration

5.2 Intel® Rapid Storage Technology enterprise

SATA/SSATA Option ROM Utility

The Intel® Rapid Storage Technology enterprise SATA/SSATA Option ROM utility allows you

to create RAID 0, RAID 1, RAID 10 (RAID 1+0), and RAID 5 set from Serial ATA hard disk

drives that are connected to the Serial ATA connectors supported by the Southbridge.

The navigation keys at the bottom of the screen allow you to move through the menus

and select the menu options.

The RAID BIOS setup screens shown in this section are for reference only and may not

exactly match the items on your screen.

To launch the Intel® Rapid Storage Technology enterprise SATA/SSATA Option ROM utility:

1. Turn on the system.

2. During POST, press <Ctrl>+<I> to display the utility main menu.

Before you proceed, ensure that you have installed the Serial ATA hard disk drives, and

have set the correct SATA mode in the BIOS setup. You can refer to the Installing Serial

ATA hard disks, and Setting the RAID item in BIOS sections in this manual for more

information.

[ESC]-Exit [ENTER]-Select Menu[ ]-Select

Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023

[ MAIN MENU ]

[ DISK/VOLUME INFORMATION]

RAID Volumes:

None defined.

Physical Disks:

ID Drive Model Serial # Size Type/Status(Vol ID)

0 ST3300656SS HWAS0000991753TR 279.3GB Non-RAID Disk

1 ST3300656SS 37VN00009846RAJ1 279.3GB Non-RAID Disk

2 ST3300656SS 397600009846UEDY 279.3GB Non-RAID Disk

3 ST3300656SS GWC50000991756G6 279.3GB Non-RAID Disk

3. Reset Disks to Non-RAID

4. Exit

1. Create RAID Volume

2. Delete RAID Volume

5-5

Z11PA-U12 Series

5.2.1 Creating a RAID set

To create a RAID set:

1. From the utility main menu, select 1. Create RAID Volume and press <Enter>.

2. Key in a name for the RAID set and press <Enter>.

3. Press the up/down arrow keys to select a RAID Level that you wish to create then

press <Enter>.

4. From the Disks item eld, press <Enter> to select the hard disk drives that you want to

include in the RAID set.

5. Use the up/down arrow keys to move the selection bar then press <Space> to select a

disk. A small triangle before the Port number marks the selected drive. Press <Enter>

when you are done.

[ESC]-Previous Menu [ENTER]-Select[ ]Change

Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023

[ CREATE VOLUME MENU ]

[ HELP ]

Name:

RAID Level:

Disks:

Strip Size:

Capacity:

Syne:

Create Volume

Enter a unique volume name that has no special characters and is

16 characters or less.

Volume0

RAID0(Strips)

Select Disks

128KB

0.0 GB

N/A

[TAB]-Next

[ SELECT DISKS ]

Port Drive Model Serial # Size Status

0 ST3300656SS HWAS0000991753TR 279.3GB Non-RAID Disk

1 ST3300656SS 37VN00009846RAJ1 279.3GB Non-RAID Disk

2 ST3300656SS 397600009846UEDY 279.3GB Non-RAID Disk

3 ST3300656SS GWC50000991756G6 279.3GB Non-RAID Disk

Select 1 Master and 1 Recovery disk to create volume.

[ ]-Prev/Next [TAB]-(M)aster [SPACE]-(R)ecovery [ENTER]-Done

5-6 Chapter 5: RAID Conguration

6. Use the up/down arrow keys to select the stripe size for the RAID array (for RAID 0,

10 and 5 only) then press <Enter>. The available stripe size values range from 4 KB to

128 KB. The following are typical values:

RAID 0: 128KB

RAID 10: 64KB

RAID 5: 64KB

We recommend a lower stripe size for server systems, and a higher stripe size for

multimedia computer systems used mainly for audio and video editing.

7. In the Capacity eld item, key in the RAID volume capacity that you want to use and

press <Enter>. The default value eld indicates the maximum allowed capacity.

8. Press <Enter> to start creating the RAID volume.

9. From the following warning message, press <Y> to create the RAID volume and return

to the main menu, or press <N> to go back to the CREATE VOLUME menu.

WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.

Are you sure you want to create this volume? (Y/N):

5-7

Z11PA-U12 Series

5.2.2 Deleting a RAID set

Take caution when deleting a RAID set. You will lose all data on the hard disk drives when

you delete a RAID set.

To delete a RAID set:

1. From the utility main menu, select 2. Delete RAID Volume and press <Enter>.

2. From the Delete Volume Menu, press the up/down arrow keys to select the RAID set

you want to delete then press <Del>.

3. Press <Y> to conrm deletion of the selected RAID set and return to the utility main

menu, or press <N> to return to the DELETE VOLUME menu.

[ESC]-Previous Menu[ ]-Select

Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023

[ DELETE VOLUME MENU ]

[ HELP ]

Deleting a volume will reset the disks to non-RAID

WARNING: ALL DISK DATA WILL BE DELETED.

(This does not apply to Recovery volumes)

[DEL]-Delete Volume

Name Level Drives Capacity Status Bootable

Volume0 RAID0(Stripe) 2 298.0GB Normal Yes

ALL DATA IN THE VOLUME WILL BE LOST!

(This does not apply to Recovery volumes)

Are you sure you want to delete volume “Volume0”? (Y/N):

[ DELETE VOLUME VERIFICATION ]

5-8 Chapter 5: RAID Conguration

5.2.3 Resetting disks to Non-RAID

Take caution before you reset a RAID volume hard disk drive to non-RAID. Resetting a

RAID volume hard disk drive deletes all internal RAID structure on the drive.

To reset a RAID set:

1. From the utility main menu, select 3. Reset Disks to Non-RAID and press <Enter>.

2. Press the up/down arrow keys to select the drive(s) or disks of the RAID set you want

to reset, then press <Space>. A small triangle before the Port number marks the

selected drive. Press <Enter> when you are done.

3. Press <Y> in the conrmation window to reset the drive(s) or press <N> to return to the

utility main menu.

Port Drive Model Serial # Size Status

0 ST3300656SS HWAS0000991753TR 279.3GB Member Disk

1 ST3300656SS 37VN00009846RAJ1 279.3GB Member Disk

Select the disks that should be reset.

Resetting RAID disk will remove its RAID structures

and revert it to a non-RAID disk.

[ ]-Previous/Next [SPACE]-Selects [ENTER]-Selection Complete

[ RESET RAID DATA ]

WARNING: Resetting a disk causes all data on the disk to be lost.

(This does not apply to Recovery volumes)

5-9

Z11PA-U12 Series

Select a destination disk with the same size as the original hard disk.

5.2.5 Rebuilding the RAID

This option is only for the RAID 1 set.

Rebuilding the RAID with other non-RAID disk

If any of the SATA hard disk drives included in the RAID 1 array failed, the system displays

the status of the RAID volume as “Degraded” during POST. You can rebuild the RAID array

with other installed non-RAID disks.

To rebuild the RAID with other non-RAID disk:

1. During POST, press <Ctrl>+<I> at the prompt to enter the Intel Rapid Storage

Technology option ROM utility.

2. If there is a non-RAID SATA Hard Disk available, the utility will prompt you to rebuild

the RAID. Press the up/down arrow keys to select the destination disk then Press

<Enter> to start the rebuilding process, or press <ESC> to exit.

5.2.4 Exiting the Intel® Rapid Storage Technology enterprise

SATA/SSATA Option ROM utility

To exit the utility:

1. From the utility main menu, select 4. Exit then press <Enter>.

2. Press <Y> to exit or press <N> to return to the utility main menu.

Select the port of destination disk for rebuilding (ESC to exit):

Port Drive Model Serial # Size

X XXXXXXXXXXX XXXXXXXX XXX.GB

“Degraded” volume and disk available for rebuilding detected. Selectign

a disk initiates a rebuild. Rebuild completes in the operating system.

[ ]-Previous/Next [ENTER]-Select [ESC]-Exit

[ DEGRADED VOLUME DETECTED ]

Are you sure you want to exit? (Y/N):

[ CONFIRM EXIT ]

5-10 Chapter 5: RAID Conguration

3. The utility immediately starts rebuilding after the disk is selected. When done, the

status of the degraded RAID volume is changed to “Rebuild”.

4. Press <Esc> to exit Intel Rapid Storage Technology and reboot the system.

5. Select Start > Programs > Intel Rapid Storage > Intel Rapid Storage Console or

click the Intel Rapid Storage Technology tray icon to load the Intel Rapid Storage

Manager utility.

6. From the View menu, select Advanced Mode to display the details of the Intel Rapid

Storage Console.

7. From the Volumes view option, select RAID volume to view the rebuilding status.

When nished, the status is changed to “Normal”.

Rebuilding the RAID with a new hard disk

If any of the SATA hard disk drives included in the RAID array failed, the system displays the

status of the RAID volume as “Degraded” during POST. You may replace the disk drive and

rebuild the RAID array.

To rebuild the RAID with a new hard disk:

1. Remove the failed SATA hard disk and install a new SATA hard disk of the same

specication into the same SATA Port.

Select a destination disk with the same size as the original hard disk.

2. Reboot the system then follow the steps in section Rebuilding the RAID with other

non-RAID disk.

[ESC]-Exit [ENTER]-Select Menu[ ]-Select

Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023

[ MAIN MENU ]

[ DISK/VOLUME INFORMATION]

RAID Volumes: *=Data is Encrypted

ID Name Level1 Strip Size Status Bootable

1 Volume0 RAID1(Mirror) N/A 149.0GB Rebuild Yes

Physical Devices:

Port Drive Model Serial # Size Type/Status(Vol ID)

1 ST3160812AS 9LS0F4HL 149.0GB Member Disk(0)

2 ST3160812AS 3LS0JYL8 149.0GB Member Disk(0)

Volumes with “Rebuild” status will be rebuilt within the operating system.

3. Reset Disks to Non-RAID

4. Exit

1. Create RAID Volume

2. Delete RAID Volume

5-11

Z11PA-U12 Series

5.2.6 Setting the Boot array in the BIOS Setup Utility

You can set the boot priority sequence in the BIOS for your RAID arrays when creating multi-

RAID using the Intel® Rapid Storage Technology enterprise SATA Option ROM utililty.

To set the boot array in the BIOS:

Set at least one of the arrays bootable to boot from the hard disk.

1. Reboot the system and press <Del> to enter the BIOS setup utility during POST.

2. Go to the Boot menu and select the boot option priority.

3. Use up/down arrow keys to select the boot priority and press <Enter>. See the Boot

menu section of Chapter 4 for more details.

4. From the Exit menu, select Save Changes & Exit, then press <Enter>.

5. When the conrmation window appears, select Yes, then press <Enter>.

5-12 Chapter 5: RAID Conguration

5.3 Intel® Rapid Storage Technology enterprise

(Windows)

The Intel® Rapid Storage Technology enterprise allows you to create RAID 0, RAID 1, RAID

10 (RAID 1+0), and RAID 5 set(s) from Serial ATA hard disk drives that are connected to the

Serial ATA connectors supported by the Southbridge.

You can click Rescan to re-scan any attached hard disks.

1. Turn on the system and go to the windows desktop.

2. Click the Intel® Rapid Storage Technology enterprise icon to display the main menu.

Your storage system is congured for data protection, increased performance and

optimal data storage capacity. You can create additional volumes to further optimize

your storage system.

To enter the Intel® Rapid Storage Technology enterprise utility under Windows operating

system:

You need to manually install the Intel® Rapid Storage Technology enterprise utility on a

Windows® operating system. Please refer to the installation instructions in Chapter 6.

5-13

Z11PA-U12 Series

5.3.1 Creating a RAID set

To create a RAID set:

1. From the utility main menu, select Create Volume and select volume type.

2. Click Next.

3. Enter a name for the RAID set, then select the array disks.

4. Select Volume Size tab, you can drag the bar to decide the volume size.

5. Click Next.

• If you do not want to keep the data on one of the selected disks, select NO when

prompted.

• If you want to Enable volume write-back cache or Initialize volume, click

Advanced.

5-14 Chapter 5: RAID Conguration

6. Conrm the volume creation, than click Create Volume to continue.

This process could take a while depending on the number and size of the disks. You can

continue using other applications during this time.

7. Wait until the process is completed, then click OK when prompted.

You still need to partition your new volume using Windows Disk Management before

adding any data.

The RAID set is displayed in the Volumes list and you can change the settings in

Volume Properties.

5-15

Z11PA-U12 Series

5.3.2 Changing a Volume Type

To change the volume type in Volume Properties:

1. Click the SATA array items you want to change in Volumes eld.

2. From the Volume Properties eld, select Type:RAID 1 Change type.

We recommend a lower stripe size for server systems, and a higher stripe size for

multimedia computer systems used mainly for audio and video editing.

3. You can change the Name, Select the new volume type, and Select additional

disks to include in the new volume if needed.

4. Select the Data stripe size for the RAID array (for RAID 0, 10 and 5 only), and click

OK. The available stripe size values range from 4 KB to 128 KB. The following are

typical values:

RAID 0: 128KB

RAID 10: 64KB

RAID 5: 64KB

5-16 Chapter 5: RAID Conguration

5.3.3 Deleting a volume

Be cautious when deleting a volume. You will lose all data on the hard disk drives.Before

you proceed, ensure that you back up all your important data from your hard drives.

To delete a volume:

1. From the utility main menu, select the volume (exp. Volume_0000) in Volumes eld

you want to delete.

3. Click Yes to delete the volume and return to the utility main menu, or click No to return

to the main menu.

2. Select Delete volume in Volume Properties eld. The following screen appears.

5-17

Z11PA-U12 Series

5.3.4 Preferences

System Preferences

Allow you to set to show the notication area icon and show system information, warning, or

errors here.

E-Mail Preferences

Allow you to set to sent e-mail of the following events:

• Storage system information

• Storage system warnings

• Storage system errors

5-18 Chapter 5: RAID Conguration

5.4 Intel® Virtual Raid on CPU in BIOS

This feature requires a KEY module to enable CPU RAID functions with Intel® CPU RSTe.

• The KEY module is purchased separately.

• Refer to section 2.8.2 Internal connectors for the location of the VROC_HW_KEY

connector.

Due to hardware design, your motherboard does not support CPU RAID congurations as

OS drives.

To enter the Intel® Virtual Raid on CPU in BIOS:

1. Enter the BIOS Setup during POST.

2. Go to the Advanced menu > Intel(R) Virtual Raid on CPU > All Intel VMD

Controllers then press <Enter> to display the Intel® Virtual Raid on CPU menu.

Refer to Chapter 4 for details on entering and navigating through the BIOS Setup.

Due to chipset limitation, when SATA ports are set to RAID mode, all SATA ports run at

RAID mode together.

5-19

Z11PA-U12 Series

5.4.1 Creating a RAID set

To create a RAID set:

1. From the Intel® Virtual Raid on CPU menu, select Create RAID Volume and press

<Enter>. The following screen appears:

2. When the Name item is selected, enter a name for the RAID set and press <Enter>.

3. When the RAID Level item is selected, press <Enter> to select the RAID level to

create, and then press <Enter>.

4. When the Enable RAID spanned over VMD Controllers item is selected, press

<Enter> and select X to enable this function.

5. Under Select Disks, press <Enter> and select X for the disks you want to include in the

RAID set.

6. When the Strip Size item is selected, press <Enter> to select strip size for the RAID

array (for RAID 0, 10 and 5 only), and then press <Enter>. The available strip size

values range from 4 KB to 128 KB. The following are typical values:

- RAID 0: 128 KB

- RAID 10: 64 KB

- RAID 5: 64 KB

We recommend a lower strip size for server systems, and a higher strip size for multimedia

computer systems used mainly for audio and video editing.

5-20 Chapter 5: RAID Conguration

7. When the Capacity (MB) item is selected, enter the RAID volume capacity that you

want and press <Enter>. The default value indicates the maximum allowed capacity.

8. When the Create Volume item is selected, press <Enter> to create the RAID volume

and return to the Intel® Rapid Storage Technology menu.

5-21

Z11PA-U12 Series

2. When the Delete item is selected, press <Enter>, then select Yes to delete the RAID

volume and return to the Intel® Virtual Raid on CPU menu, or select No to cancel.

5.4.2 Deleting a RAID set

Be cautious when deleting a RAID set. You will lose all data on the hard disk drives when

you delete a RAID set.

To delete a RAID set:

1. From the Intel® Virtual Raid on CPU menu, select the RAID volume you want to delete

and press <Enter>. The following screen appears:

5-22 Chapter 5: RAID Conguration

5.4.3 Installing the RAID controller driver during Windows®

10 OS installation

This part provides the instructions on how to install the RAID controller drivers during OS

installation.

To install the RAID controller driver when installing Windows® 10 OS:

1. Boot the computer using the Windows® 10 OS installation disc. Follow the screen

instructions to start installing Windows® 10.

2. When prompted to choose a type of installation, click Custom: Install Windows only

(advanced).

3. Click Load Driver.

5-23

Z11PA-U12 Series

4. A message appears, reminding you to insert the installation media containing the driver

of the RAID controller driver. If you have only one optical drive installed in your system,

eject the Windows OS installation disc and replace with the motherboard Support DVD

into the optical drive. Click Browse to continue.

5. Locate the driver in the corresponding folder of the support DVD then click OK to

continue.

6. Select the RAID controller driver you need from the list and click Next.

7. When the system nishes loading the RAID driver, replace the motherboard Support

DVD with the Windows Server installation disc. Select the drive to install Windows and

click Next.

8. Setup then proceeds with the OS installation. Follow screen instructions to continue.

5-24 Chapter 5: RAID Conguration

Driver Installation

Chapter 6: Driver Installation

This chapter provides the instructions for installing the

necessary drivers for different system components in the

Windows® Operating Systems.

6-2 Chapter 6: Driver Installation

6.1 RAID driver installation

After creating the RAID sets for your server system, you are now ready to install an

operating system to the independent hard disk drive or bootable array. This part provides the

instructions on how to install the RAID controller drivers during OS installation.

6.1.1 Creating a USB flash drive with RAID drive

When installing Windows® Server OS, you can load the RAID driver from a USB ash drive.

You can create a USB ash drive with RAID driver in Windows by copying the les from the

support DVD to the USB ash drive.

To copy the RAID driver to a USB ash drive in Windows environment:

1. Place the motherboard support DVD in the optical drive.

2. Connect a USB ash drive to your system.

3. Click on the optical drive to browse the contents of the support DVD.

4. Click

Drivers > C620 INTEL RAID > Windows > Driver and then copy the RAID driver

folder to the USB ash drive.

6.1.2 Installing the RAID controller driver

During Windows® Server 2012 R2 OS installation

To install the RAID controller driver when installing Windows® Server 2012 R2 OS:

1. Boot the computer using the Windows® Server 2012 R2 OS installation disc. Follow the

screen instructions to start installing Windows Server 2012 R2.

2. When prompted to choose a type of installation, click Custom: Install Windows only

(advanced).

Z11PA-U12 Series 6-3

3. Click Load Driver.

4. A message appears reminding you to insert the installation media containing the driver of

the RAID controller driver (the installation media can be a CD, DVD, or USB ash drive).

• If you have only one optical drive installed in your system, eject the Windows OS

installation disc and replace with the motherboard Support DVD into the optical

drive.

• Or you may connect a USB ash drive containing the RAID controller driver.

Click Browse to continue.

5. Locate the driver in the corresponding folder of the Support DVD or USB ash drive

and then click OK to continue.

6. Select the RAID controller driver you need from the list and click Next.

6-4 Chapter 6: Driver Installation

7. When the system nishes loading the RAID driver,

• Replace the motherboard Support DVD with the Windows Server installation disc.

• Remove the USB ash drive.

Select the drive to install Windows and click Next.

8. Setup then proceeds with the OS installation. Follow screen instructions to continue.

Z11PA-U12 Series 6-5

6.2 Management applications and utilities installation

When you place the support DVD into the optical drive, the DVD automatically displays the

main screen if Autorun is enabled in your computer. By default, the Drivers tab is displayed.

If Autorun is NOT enabled in your computer, browse the contents of the support DVD to

locate the le ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run

the support DVD.

6.3 Running the Support DVD

• The contents of the support DVD are subject to change at any time without notice.

Visit the ASUS website (www.asus.com) for the latest updates on software and

utilities.

• The support DVD is supported on Windows® Server 2012 R2 and Windows® Server

2016.

The support DVD that is bundled with your motherboard contains drivers, management

applications, and utilities that you can install to maximize the features of your motherboard.

The main screen of the Support DVD contains the following tabs:

1. Drivers

2. Utilities

3. Manual

4. Contact

The main screen of the Support DVD looks exactly the same on the Windows® Server 2012

R2 and on the Windows® Server 2016 Operating System (OS).

6-6 Chapter 6: Driver Installation

The Drivers Menu shows the available device drivers if the system detects installed devices.

Install the necessary drivers to activate the devices.

6.3.2 Utilities menu tab

The Utilities menu displays the software applications and utilities that the motherboard supports.

6.3.1 Drivers menu tab

Z11PA-U12 Series 6-7

6.3.3 Manual menu

The Manual menu provides the link to the Broadcom NetXtreme II Network Adapter user guide.

You need an internet browser installed in your OS to view the User Guide.

6.3.4 Contact information menu

The Contact menu displays the ASUS contact information, e-mail addresses, and useful links

if you need more information or technical support for your motherboard.

6-8 Chapter 6: Driver Installation

6.4 Intel® chipset device software installation

This section provides the instructions on how to install the Intel® chipset device software on

the system.

You need to manually install the Intel® chipset device software on a Windows operating

system.

To install the Intel® chipset device software:

1. Restart the computer, and then log on with Administrator privileges.

2. Insert the motherboard/system support DVD into the optical drive. The support DVD

automatically displays the Drivers menu if Autorun is enabled in your computer.

If Autorun is NOT enabled in your computer, browse the contents of the support DVD to

locate the le ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run

the support DVD.

3. Click the item Intel® Chipset Device Software from the menu.

4. The

Intel® Chipset Device Software window appears. Click Next to start the

installation.

Z11PA-U12 Series 6-9

5. Read the License Agreement and click Accept to continue the process.

6. Read the Readme File Information and click Install to start the installation process.

7. Click Restart Now to complete the setup process.

6-10 Chapter 6: Driver Installation

5. Click Install Drivers and Software option to begin installation.

6.5 Installing the Intel® I210 Gigabit Adapters driver

This section provides the instructions on how to install the Intel® I210 Gigabits Adapter

Driver on the system.

To install the Intel® I210 Gigabit Adapters Driver on the Windows® operating system:

1. Restart the computer.

2. Log on with Administrator privileges.

3. Insert the motherboard/system support DVD to the optical drive.

If Autorun is NOT enabled in your computer, browse the contents of the support DVD to

locate the le ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run

the support DVD.

4. Click Intel® I350-AM1/I350-AM2/I210 Gigabit Adapters Driver in the Drivers menu of

the main screen to start the installation.

Z11PA-U12 Series 6-11

6. Click Next when the Intel(R) Network Connections Install Wizard window appears.

7. Tick I accept the terms in the license agreement and click Next to continue.

8. From the Setup Options window, click Next to start the installation.

By default, Intel(R) PROSet for Windows Device Manager and Windows PowerShell

Module are ticked.

6-12 Chapter 6: Driver Installation

9. Click Install to start the installation.

10. When the installation is done, press Finish to complete the installation.

Z11PA-U12 Series 6-13

6.7 Intel® Rapid Storage Technology enterprise 5.0

installation

This section provides the instructions on how to install the Intel® Rapid Storage Technology

enterprise 5.0 on the system.

You need to manually install the Intel® Rapid Storage Technology enterprise 5.0 utility on a

Windows® operating system.

To install the Intel® Rapid Storage Technology enterprise 5.0 utility:

1. Restart the computer, and then log on with Administrator privileges.

2. Insert the motherboard/system support DVD into the optical drive, and navigate to the

Utilities menu.

3. Click the Intel® Rapid Storage Technology enterprise to begin installation.

4. The

Intel® Rapid Storage Technology enterprise window appears. Click Next to start

the installation.

6-14 Chapter 6: Driver Installation

5. Read the Warning message and click Next to continue.

6. Read the License Agreement and click Accept to continue the process.

7. Select the destination folder and click Next to continue.

Z11PA-U12 Series 6-15

8. Tick the features that you would like to install and click Next to continue.

9. Click Install to start the installation process.

10. Click Restart Now to complete the setup process.

6-16 Chapter 6: Driver Installation

Appendix

This appendix includes additional information that you may

refer to when conguring the motherboard.

Appendix

A-2 Appendix

Z11PA-U12 Series block diagram

Z11PA-U12/10G-2S

Z11PA-U12 Series A-3

Z11PA-U12

A-4 Appendix

Q-Code table

Action PHASE POST CODE TYPE DESCRIPTION

Normal boot

Security Phase

01 Progress First post code(POWER_ON_POST_CODE)

02 Progress Load BSP microcode(MICROCODE_POST_CODE)

03 Progress Set cache as ram for PEI phase(CACHE_ENABLED_POST_CODE)

06 Progress CPU Early init.(CPU_EARLY_INIT_POST_CODE)

04 Progress initializes South bridge for PEI preparation

PEI (Pre-EFI

initialization) phase

10 Progress PEI Core Entry

15 Progress NB initialize before installed memory

19 Progress SB initialize before installed memory

78~00 Progress Wait BMC ready(duration: 120 seconds)

A1 MRC Progress QPI initialization

A3 MRC Progress QPI initialization

A7 MRC Progress QPI initialization

A8 MRC Progress QPI initialization

A9 MRC Progress QPI initialization

AA MRC Progress QPI initialization

AB MRC Progress QPI initialization

AC MRC Progress QPI initialization

AD MRC Progress QPI initialization

AE MRC Progress QPI initialization

AF MRC Progress QPI initialization Complete

2F Progress Memory Init.

B0 MRC Progress Memory Init.

B1 MRC Progress Memory Init.

AF MRC Progress RC Reset if require

B4 MRC Progress Memory Init.

B2 MRC Progress Memory Init.

B3 MRC Progress Memory Init.

B5 MRC Progress Memory Init.

B6 MRC Progress Memory Init.

B7 MRC Progress Memory Init.

B8 MRC Progress Memory Init.

B9 MRC Progress Memory Init.

BA MRC Progress Memory Init.

BB MRC Progress Memory Init.

BC MRC Progress Memory Init.

BF MRC Progress Memory Init. Done

5A MRC Progress Other cong. After RC end

31 Progress Memory already installed

32 Progress CPU Init.

34 Progress CPU Init.

36 Progress CPU Init.

4F Progress DXE Initial Program Load(IPL)

(continued on the next page)

Z11PA-U12 Series A-5

Action PHASE POST CODE TYPE DESCRIPTION

Normal boot

DXE (Driver

Execution

Environment) phase

60 Progress DXE Core Started

61 Progress DXE NVRAM Init.

62 Progress SB run-time init.

63 Progress DXE CPU Init

68 Progress NB Init.

69 Progress NB Init.

6A Progress NB Init.

70 Progress SB Init.

71 Progress SB Init.

72 Progress SB Init.

78 Progress ACPI Init.

79 Progress CSM Init.

BDS (Boot Device

Selection) phase

90 Progress BDS started

91 Progress Connect device event

92 Progress PCI Bus Enumeration.

93 Progress PCI Bus Enumeration.

94 Progress PCI Bus Enumeration.

95 Progress PCI Bus Enumeration.

96 Progress PCI Bus Enumeration.

97 Progress Console outout connect event

98 Progress Console input connect event

99 Progress AMI Super IO start

9A Progress AMI USB Driver Init.

9B Progress AMI USB Driver Init.

9C Progress AMI USB Driver Init.

9D Progress AMI USB Driver Init.

b2 Progress Legacy Option ROM Init.

b3 Progress Reset system

b4 Progress USB hotplug

b6 Progress NVRAM clean up

b7 Progress NVRAM conguration reset

A0 Progress IDE, AHCI Init.

A1 Progress IDE, AHCI Init.

A2 Progress IDE, AHCI Init.

A3 Progress IDE, AHCI Init.

A8 Progress BIOS Setup Utility password verify

A9 Progress BIOS Setup Utility start

AB Progress BIOS Setup Utility input wait

AD Progress Ready to boot event

AE Progress Legacy boot event

Operating system

phase

AA Progress APIC mode

AC Progress PIC mode

Q-Code table

A-6 Appendix

Română ASUSTeK Computer Inc. declară că acest dispozitiv se conformează

cerinţelor esenţiale şi altor prevederi relevante ale directivelor conexe. Textul

complet al declaraţiei de conformitate a Uniunii Europene se găseşte la:

www.asus.com/support

Srpski ASUSTeK Computer Inc. ovim izjavljuje da je ovaj uređaj u saglasnosti

sa osnovnim zahtevima i drugim relevantnim odredbama povezanih

Direktiva. Pun tekst EU deklaracije o usaglašenosti je dostupan da adresi:

www.asus.com/support

Slovensky Spoločnosť ASUSTeK Computer Inc. týmto vyhlasuje, že toto

zariadenie vyhovuje základným požiadavkám a ostatým príslušným

ustanoveniam príslušných smerníc. Celý text vyhlásenia o zhode pre štáty EÚ

je dostupný na adrese: www.asus.com/support

Slovenščina ASUSTeK Computer Inc. izjavlja, da je ta naprava skladna z

bistvenimi zahtevami in drugimi ustreznimi določbami povezanih direktiv.

Celotno besedilo EU-izjave o skladnosti je na voljo na spletnem mestu:

www.asus.com/support

Español Por la presente, ASUSTeK Computer Inc. declara que este dispositivo

cumple los requisitos básicos y otras disposiciones pertinentes de las

directivas relacionadas. El texto completo de la declaración de la UE de

conformidad está disponible en: www.asus.com/support

Svenska ASUSTeK Computer Inc. förklarar härmed att denna

enhet överensstämmer med de grundläggande kraven och andra

relevanta föreskrifter i relaterade direktiv. Fulltext av EU-försäkran om

överensstämmelse nns på: www.asus.com/support

Українська ASUSTeK Computer Inc. заявляє, що цей пристрій відповідає

основним вимогам та іншим відповідним положенням відповідних

Директив. Повний текст декларації відповідності стандартам ЄС

доступний на: www.asus.com/support

Türkçe AsusTek Computer Inc., bu aygıtın temel gereksinimlerle ve ilişkili

Yönergelerin diğer ilgili koşullarıyla uyumlu olduğunu beyan eder. AB

uygunluk bildiriminin tam metni şu adreste bulunabilir:

www.asus.com/support

Bosanski ASUSTeK Computer Inc. ovim izjavljuje da je ovaj uređaj usklađen

sa bitnim zahtjevima i ostalim odgovarajućim odredbama vezanih direktiva.

Cijeli tekst EU izjave o usklađenosti dostupan je na: www.asus.com/support

English ASUSTeK Computer Inc. hereby declares that this device is in

compliance with the essential requirements and other relevant provisions of

related Directives. Full text of EU declaration of conformity is available at:

www.asus.com/support

Français AsusTek Computer Inc. déclare par la présente que cet appareil est

conforme aux critères essentiels et autres clauses pertinentes des directives

concernées. La déclaration de conformité de l’UE peut être téléchargée à

partir du site Internet suivant : www.asus.com/support

Deutsch ASUSTeK Computer Inc. erklärt hiermit, dass dieses Gerät mit

den wesentlichen Anforderungen und anderen relevanten Bestimmungen

der zugehörigen Richtlinien übereinstimmt. Der gesamte Text der EU-

Konformitätserklärung ist verfügbar unter: www.asus.com/support

Italiano ASUSTeK Computer Inc. con la presente dichiara che questo

dispositivo è conforme ai requisiti essenziali e alle altre disposizioni pertinenti

con le direttive correlate. Il testo completo della dichiarazione di conformità

UE è disponibile all’indirizzo: www.asus.com/support

Русский Компания ASUS заявляет, что это устройство соответствует

основным требованиям и другим соответствующим условиям

соответствующих директив. Подробную информацию, пожалуйста,

смотрите на www.asus.com/support

Български С настоящото ASUSTeK Computer Inc. декларира, че това

устройство е в съответствие със съществените изисквания и другите

приложими постановления на свързаните директиви. Пълният текст на

декларацията за съответствие на ЕС е достъпна на адрес:

www.asus.com/support

Hrvatski ASUSTeK Computer Inc. ovim izjavljuje da je ovaj uređaj sukladan

s bitnim zahtjevima i ostalim odgovarajućim odredbama vezanih direktiva.

Cijeli tekst EU izjave o sukladnosti dostupan je na: www.asus.com/support

Čeština Společnost ASUSTeK Computer Inc. tímto prohlašuje, že toto

zařízení splňuje základní požadavky a další příslušná ustanovení souvisejících

směrnic. Plné znění prohlášení o shodě EU je k dispozici na adrese:

www.asus.com/support

Dansk ASUSTeK Computer Inc. erklærer hermed, at denne enhed er i

overensstemmelse med hovedkravene og andre relevante bestemmelser i de

relaterede direktiver. Hele EU-overensstemmelseserklæringen kan ndes på:

www.asus.com/support

Nederlands ASUSTeK Computer Inc. verklaart hierbij dat dit apparaat

voldoet aan de essentiële vereisten en andere relevante bepalingen van

de verwante richtlijnen. De volledige tekst van de EU-verklaring van

conformiteit is beschikbaar op: www.asus.com/support

Eesti Käesolevaga kinnitab ASUSTeK Computer Inc, et see seade vastab

asjakohaste direktiivide oluliste nõuetele ja teistele asjassepuutuvatele

sätetele. EL vastavusdeklaratsiooni täielik tekst on saadaval järgmisel

aadressil: www.asus.com/support

Suomi ASUSTeK Computer Inc. ilmoittaa täten, että tämä laite on

asiaankuuluvien direktiivien olennaisten vaatimusten ja muiden tätä

koskevien säädösten mukainen. EU-yhdenmukaisuusilmoituksen koko teksti

on luettavissa osoitteessa: www.asus.com/support

Ελληνικά Με το παρόν, η AsusTek Computer Inc. δηλώνει ότι αυτή η

συσκευή συμμορφώνεται με τις θεμελιώδεις απαιτήσεις και άλλες σχετικές

διατάξεις των Οδηγιών της ΕΕ. Το πλήρες κείμενο της δήλωσης συμβατότητας

είναι διαθέσιμο στη διεύθυνση: www.asus.com/support

Magyar Az ASUSTeK Computer Inc. ezennel kijelenti, hogy ez az eszköz

megfelel a kapcsolódó Irányelvek lényeges követelményeinek és egyéb

vonatkozó rendelkezéseinek. Az EU megfelelőségi nyilatkozat teljes szövege

innen letölthető: www.asus.com/support

Latviski ASUSTeK Computer Inc. ar šo paziņo, ka šī ierīce atbilst saistīto

Direktīvu būtiskajām prasībām un citiem citiem saistošajiem nosacījumiem.

Pilns ES atbilstības paziņojuma teksts pieejams šeit: www.asus.com/support

Lietuvių „ASUSTeK Computer Inc.“ šiuo tvirtina, kad šis įrenginys atitinka

pagrindinius reikalavimus ir kitas svarbias susijusių direktyvų nuostatas. Visą

ES atitikties deklaracijos tekstą galima rasti: www.asus.com/support

Norsk ASUSTeK Computer Inc. erklærer herved at denne enheten er i

samsvar med hovedsaklige krav og andre relevante forskrifter i relaterte

direktiver. Fullstendig tekst for EU-samsvarserklæringen nnes på:

www.asus.com/support

Polski Firma ASUSTeK Computer Inc. niniejszym oświadcza, że

urządzenie to jest zgodne z zasadniczymi wymogami i innymi właściwymi

postanowieniami powiązanych dyrektyw. Pełny tekst deklaracji zgodności UE

jest dostępny pod adresem: www.asus.com/support

Português A ASUSTeK Computer Inc. declara que este dispositivo está em

conformidade com os requisitos essenciais e outras disposições relevantes

das Diretivas relacionadas. Texto integral da declaração da UE disponível em:

www.asus.com/support

Simplified EU Declaration of Conformity

Z11PA-U12 Series A-7

ASUS contact information

ASUSTeK COMPUTER INC.

Address 4F, No. 150, Li-Te Rd., Peitou, Taipei 112, Taiwan

Telephone +886-2-2894-3447

Fax +886-2-2890-7798

Web site http://www.asus.com

Technical Support

Telephone +86-21-38429911

Fax +86-21-58668722 ext: 9101

Online Support http://support.asus.com/techserv/techserv.aspx

ASUSTeK COMPUTER INC. (Taiwan)

Address 4F, No. 150, Li-Te Rd., Peitou, Taipei 112, Taiwan

Telephone +886-2-2894-3447

Fax +886-2-2890-7798

Web site http://www.asus.com

Technical Support

Telephone +886-2-2894-3447 (0800-093-456)

Online Support http://support.asus.com/techserv/techserv.aspx

ASUSTeK COMPUTER INC. (China)

Address No. 5077, Jindu Road, Minhang District, Shanghai, China

Telephone +86-21-5442-1616

Fax +86-21-5442-0099

Web site http://www.asus.com.cn

Technical Support

Telephone +86-20-2804-7506 (400-620-6655)

Online Support http://support.asus.com/techserv/techserv.aspx

A-8 Appendix

ASUS contact information

ASUS COMPUTER INTERNATIONAL (America)

Address 800 Corporate Way, Fremont, CA 94539, USA

Fax +1-510-608-4555

Web site http://usa.asus.com

Technical Support

Support fax +1-812-284-0883

General support +1-812-282-2787

Online support http://support.asus.com/techserv/techserv.aspx

ASUS COMPUTER GmbH (Germany and Austria)

Address Harkort Str. 21-23, 40880 Ratingen, Germany

Fax +49-2102-959911

Web site http://www.asus.de

Online contact http://www.asus.de/sales

Technical Support

Telephone +49-1805-010923

Support Fax +49-2102-959911

Online support http://support.asus.com/techserv/techserv.aspx

ASUS Czech Service s.r.o. (Europe)

Address Na Rovince 887, 720 00 Ostrava – Hrabová,

Czech Republic

Telephone +420-596766888

Web site http://www.asus.cz

Technical Support

Telephone +420-596-766-891

Fax +420-596-766-329

E-mail advance.rma.eu@asus.com

Online Support http://support.asus.com/techserv/techserv.aspx

Z11PA-U12 Series A-9

ASUS contact information

ASUS Holland BV (The Netherlands)

Address Marconistraat 2, 7825GD EMMEN, The Netherlands

Web site http://www.asus.com

Technical Support

Telephone +31-(0)591-5-70292

Fax +31-(0)591-666853

E-mail advance.rma.eu@asus.com

Online Support http://support.asus.com/techserv/techserv.aspx

ASUS Polska Sp. z o.o. (Poland)

Address Ul. Postępu 6, 02-676 Warszawa, Poland

Web site http://pl.asus.com

Technical Support

Telephone +48-225718033

Online Support http://support.asus.com/techserv/techserv.aspx

ASK-Service (Russia and CIS)

Address г.Москва, ул. Орджоникидзе, д.10, Россия

Telephone (495) 640-32-75

Web site http://ru.asus.com

Technical Support

Telephone 008-800-100-ASUS (008-800-100-2787)

Online Support https://www.asus.com/support/Product/ContactUs/Services/

questionform/?lang=ru-ru

A-10 Appendix

DECLARATION OF CONFORMITY

Per FCC Part 2 Section 2. 1077(a)

Responsible Party Name: Asus Computer International

Address: 800 Corporate Way, Fremont, CA 94539.

Phone/Fax No: (510)739-3777/(510)608-4555

hereby declares that the product

Product Name : Motherboard

Model Number : Z11PA-U12/10G-2S

Conforms to the following specifications:

FCC Part 15, Subpart B, Unintentional Radiators

Supplementary Information:

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Representative Person’s Name : Steve Chang / President

Signature :

Date : Sep. 08, 2017

Ver. 170324

Z11PA-U12 Series A-11

DECLARATION OF CONFORMITY

Per FCC Part 2 Section 2. 1077(a)

Responsible Party Name: Asus Computer International

Address: 800 Corporate Way, Fremont, CA 94539.

Phone/Fax No: (510)739-3777/(510)608-4555

hereby declares that the product

Product Name : Motherboard

Model Number : Z11PA-U12

Conforms to the following specifications:

FCC Part 15, Subpart B, Unintentional Radiators

Supplementary Information:

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Representative Person’s Name : Steve Chang / President

Signature :

Date : Sep. 08, 2017

Ver. 170324

A-12 Appendix

Table of Contents

ASUS Z11PA-U12 User Manual

Related Manuals