Table of Contents
NETGEAR AGM731F User Manual
Displayed below is the user manual for AGM731F by NETGEAR which is a product in the Network Transceiver Modules category. This manual has pages.
Related Manuals
Installation Guide
e
ProSafe® GBIC SFP Modules AGM731F and AGM732F
Package Contents
• ProSafe® GBIC SFP Modules AGM731F and AGM732F
• Installation Guide
Install Your Optical Module
The 1000Base-X SFP Module provides full-duplex 1000 M bps Ethernet operation in
each direction for NETGEAR managed switches.
The switch automatically detects the module, so you can simply plug it into an
available module slot. Plugging in an SFP module disables the associated RJ-45
port.
Because invisible laser radiation might be emitted
from the aperture of the port when no fiber cable is
connected, avoid exposure to laser radiation and do
not stare into open apertures.
The module can be inserted or removed while the switch is operational.
F
AGM731F or AGM732F
Install a Module
Insert the module firmly into the slot that supports the SFP interface. You should
hear a click when the module is firmly seated.
Remove a Module
Release the module latch by pulling down the handle bar across the module, and
pull the module out of the module slot.
Table 1. Technical Specifications
Statement of Conditions
In the interest of improving internal design, operational function, and reliability,
NETGEAR reserves the right to change the product described in this document
without notice. NETGEAR does not assume any liability that may accrue due to the
use or application of the product(s) or circuit layout(s) described herein.
Standards IEEE 802.3z
AGM731F 1000Base -SX
AGM732F 1000Base-LX
Connectors AGM731F: SC for 62.5 um or 50 um cable
AGM732F: LC for 9 um cable
Operating temperature 32 to104º F (0 to 40ºC)
Storage temperature 14 to158 ºF (–10 to 70ºC)
Operating relative humidity 10 to 90% non-condensing
Operating altitude AGM731F: up to 3 Km (10 K ft)
AGM732F: up to 10 Km (32.8 K ft)
Operating distance AGM731F: 550 m
AGM732F: 10Km
Power consumption 500 mW
MTBF AGM731F: >10 years
AGM732F: >10 years
Safety certification UL 1950, CSA 22.2 No.60 950
Environmental compliance RoHS
AGM731F-AGM732F IG 17Oct11.fm Page 1 Monday, October 17, 2011 11:54 AM
September 2011
This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste
Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union,
this product should be treated and recycled in accordance with the laws of your jurisdiction
implementing the WEEE Directive.
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of
NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to
change without notice. Other brand and product names are registered trademarks or trademarks of their
respective holders. © 2011 NETGEAR, Inc. All rights reserved.
Regulatory Compliance
Certificate of Manufacture/Importer
It is hereby certified the NETGEAR model AGM731F and AGM732F has been
suppressed in accordance with the condition set out in MBPT-Amtsb|Vfg 243/1991
and vfg 46/1992. The operation of some equipment (for example, test transmitters)
in accordance with regulation may, however, be subject to certain restrictions.
Please refer to the note in the operating instructions. Federal Office for
Telecommunications Approvals has been notified of the placing of this equipment on
the market and has been granted the right to test the series for compliance with
regulation.
Note: This device has been tested and found to comply with limits for a Class B
digital device, pursuant to part 15 of FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a commercial
installation.
EN 55 024 Declaration of Conformance
This is to certify that the NETGEAR Model AGM731F/AGM732F is shielded against
the generation of radio interference in accordance with the application of Council
Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN55
024 Class A (CISPR 22).
FCC Compliance Notice: Radio Frequency Interference
This device complies with part 15 of the FCC rules.
Operation is subject to the following conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case users will be required to take whatever
measures may be necessary to correct the interference at their own expense.
FCC Caution
• Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
• For product available in the USA market, only channel 1~11 can be operated. Selection
of other channels is not possible.
• This device and its antenna(s) must not be co-located or operation in conjunction with
any other antenna or transmitter.
Class 1 LED product.
Because invisible laser radiation may be emitted
from the aperture of the port when no fiber cable is
connected, avoid exposure to laser radiation and do
not stare into open apertures.
Class 1 laser product.
Technical Support
Thank you for selecting NETGEAR products.
After installing your device, locate the serial number on the label of your product,
and use it to register your product at http://www.NETGEAR.com/register. Registration
is required to use the NETGEAR telephone support service. For product updates,
additional documentation, and support go to http://support.netgear.com.
For complete DoC go to the NETGEAR EU Declarations of Conformity website at
http://support.netgear.com/app/answers/detail/a_id/11621.
For GNU General Public License (GPL) related information, go to
http://support.netgear.com/app/answers/detail/a_id/2649.
WARNING!! Do not stack equipment, or place equipment in tight spaces, or in
drawers. Be sure your equipment is surrounded by at least 2 inches
of air space.
AGM731F-AGM732F IG 17Oct11.fm Page 2 Monday, October 17, 2011 11:54 AM