Table of Contents
- N600 WiFi Range Extender
- Table of Contents
- 1. Overview
- 2. Get Started
- 3. Manage the Extender Network and Security Settings
- Log In to the Extender After Initial Setup
- Change the Password
- Connect the Extender to a WiFi Network Without Using Smart Setup
- Connect the Extender to a Hidden WiFi Network
- Use WPS to Add a Device to the Extender’s WiFi Network
- Manage the Extender WiFi Settings
- Change the Extender IP Address
- Manage Advanced WiFi and WPS Settings
- Manage a WiFi Access List
- Set the Operating Mode to FastLane Technology
- Run Smart Setup Again After Initial Setup
- Connect Ethernet-Enabled Devices
- 4. Maintain and Monitor the Extender
- 5. FAQs and Troubleshooting
- A. Factory Settings and Technical Specifications
NETGEAR WN2500RP User Manual
Displayed below is the user manual for WN2500RP by NETGEAR which is a product in the Wireless Routers category. This manual has pages.
Related Manuals
350 East Plumeria Drive
San Jose, CA 95134
USA
May 2014
202-11354-01
N600 WiFi Range Extender
Model WN2500RPv2
User Manual
2
N600 WiFi Range Extender
Support
Thank you for selecting NETGEAR products.
After installing your device, locate the serial number on the label of your product and use it to register your product at
https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR
recommends registering your product through the NETGEAR website. For product updates and web support, visit
http://support.netgear.com.
Phone (US & Canada only): 1-888-NETGEAR.
Phone (Other Countries): Check the list of phone numbers at http://support.netgear.com/general/contact/default.aspx.
Compliance
For regulatory compliance information, visit http://www.netgear.com/about/regulatory.
See the regulatory compliance document before connecting the power supply.
Trademarks
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc.
and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice.
© NETGEAR, Inc. All rights reserved.
3
Table of Contents
Chapter 1 Overview
Unpack Your Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front Panel LEDs and Right Panel WPS Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Rear Panel Ports, Buttons, and Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Attach the Feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
When to Use Your Extender. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
How the Extender Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 2 Get Started
How to Position the Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Connect the Extender to Your WiFi Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Connect the Extender with WPS to a WiFi Network . . . . . . . . . . . . . . . . . . . . . . 13
Access the Extender over WiFi and Use Smart Setup . . . . . . . . . . . . . . . . . . . . . 15
Access the Extender over Ethernet and Use Smart Setup . . . . . . . . . . . . . . . . . 22
Chapter 3 Manage the Extender Network and Security Settings
Log In to the Extender After Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Change the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Connect the Extender to a WiFi Network Without Using Smart Setup. . . . . . . 33
Connect the Extender to a Hidden WiFi Network . . . . . . . . . . . . . . . . . . . . . . . . 37
Use WPS to Add a Device to the Extender’s WiFi Network. . . . . . . . . . . . . . . . . 40
Use WPS with the Push Button Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Use WPS with the PIN Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Manage the Extender WiFi Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Configure WPA, WPA2, or WPA + WPA2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Configure WEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Change the Extender IP Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Manage Advanced WiFi and WPS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Manage a WiFi Access List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Set Up and Enable the Access List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Disable the Access List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Change a Device on the Access List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Remove a Device from the Access List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Set the Operating Mode to FastLane Technology . . . . . . . . . . . . . . . . . . . . . . . . 61
Run Smart Setup Again After Initial Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Connect Ethernet-Enabled Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
4
N600 WiFi Range Extender
Chapter 4 Maintain and Monitor the Extender
Back Up and Manage the Extender Configuration . . . . . . . . . . . . . . . . . . . . . . . . 69
Back Up the Configuration Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Restore the Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Return the Extender to Its Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . 71
Use the Restore Factory Settings Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Erase the Extender Configuration Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Update the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
View the Status and Traffic Statistics of the Extender . . . . . . . . . . . . . . . . . . . . 74
View the Wired and WiFi Network Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Chapter 5 FAQs and Troubleshooting
FAQs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
You Cannot Connect to the Extender. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
You Cannot Join a WiFi Network and Receive an Error Message . . . . . . . . . . . . 82
Improve the Connection Between the Extender and the WiFi Router . . . . . . . 83
Appendix A Factory Settings and Technical Specifications
Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Technical and Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
5
1
1. Overview
This user manual is for the NETGEAR® N600 WiFi Range Extender, model WN2500RPv2, which
is referred to as the extender.
This chapter covers the following topics:
•Unpack Your Extender
•Front Panel LEDs and Right Panel WPS Button
•Rear Panel Ports, Buttons, and Connector
•Attach the Feet
•When to Use Your Extender
•How the Extender Works
Note: For more information about the topics covered in this manual, visit the
support website at support.netgear.com.
Note: Firmware updates with new features and bug fixes are made
available from time to time on downloadcenter.netgear.com. Some
products can regularly check the site and download new firmware, or
you can check for and download new firmware manually. If the
features or behavior of your product does not match what is
described in this guide, you might need to update your firmware.
Note: In this manual, the terms wireless and WiFi are interchangeable.
Overview
6
N600 WiFi Range Extender
Unpack Your Extender
Your box contains the following items:
•N600 WiFi Range Extender
•Power adapter
•Snap-on feet
•Installation guide
Front Panel LEDs and Right Panel WPS Button
Use the LEDs during installation to find the best location for the extender or to monitor the
extender performance. The following figure shows the extender in upright position, with the
feet attached. (For information about attaching the feet, see Attach the Feet on page 8.)
2.4 GHz Link Rate LED
5 GHz Link Rate LED
Device to Extender LED
LAN LEDs (1 through 4)
WPS LED
WPS button (on the right panel)
Power LED
Figure 1. Front panel LEDs and right panel WPS button
The following table describes the LEDs.
Table 1. Front panel LEDs
LED Description
Solid green. The extender is powered on.
Solid amber. The extender is booting.
Blinking amber. The firmware is upgrading or the Restore Factory Settings
button was pressed.
Blinking green. The firmware is corrupt. Visit support.netgear.com.
Off. The extender is powered off.
Green. The 2.4 GHz WiFi connection between the extender and the WiFi
router is optimum.
Amber. The 2.4 GHz WiFi connection between the extender and the WiFi
router is good.
Red. The 2.4 GHz WiFi connection between the extender and the WiFi router
is poor.
Off. The extender and the WiFi router do not have a 2.4 GHz WiFi connection.
Green. The 5 GHz WiFi connection between the extender and the WiFi router
is optimum.
Amber. The 5 GHz WiFi connection between the extender and the WiFi router
is good.
Red. The 5 GHz WiFi connection between the extender and the WiFi router is
poor.
Off. The extender and the WiFi router do not have a 5 GHz WiFi connection.
Device to Extender
LED Green. The extender is connected to a computer or WiFi device.
Off. The extender is not connected to a computer or WiFi device.
LAN LEDs
(1 through 4) Green. An Ethernet device is connected to the LAN port.
Off. No Ethernet device is connected to the LAN port.
WPS LED Solid green. WiFi security is enabled (WPA or WPA2).
Blinking green. A WPS connection is in progress.
Off. WiFi security is not enabled.
Overview
7
N600 WiFi Range Extender
Power LED
2.4 GHz Link Rate LED
5 GHz Link Rate LED
Overview
8
N600 WiFi Range Extender
Rear Panel Ports, Buttons, and Connector
The following figure shows the ports, buttons, and connector on the rear panel of the
extender. The figure show the extender in upright position, with the feet attached. (For
information about attaching the feet, see Attach the Feet on page 8.)
Restore Factory Settings button
Ethernet LAN ports
Power connector
On/Off button
Figure 2. Rear panel
Attach the Feet
If you prefer to place the extender in upright (vertical) position, attach the feet that come with
the extender.
Although the extender functions well in either horizontal or vertical position, a horizontal
position might give a better performance.
To attach the feet:
1. Hold the extender in upright position with the left side of the extender pointing down.
2. Snap the feet onto the extender.
Overview
9
N600 WiFi Range Extender
Figure 3. Attaching the feet
When to Use Your Extender
NETGEAR recommends that you connect to the extender only when your existing home
network connection is poor. Data traffic routed through the extender is inherently slower than
traffic routed directly from the network.
NETGEAR recommends that you connect through the extender network only when the WiFi
device is in a “dead zone” where connection from the existing network is poor or nonexistent.
How the Extender Works
The extender works like a bridge between a WiFi router (or a WiFi access point) and a WiFi
device outside the range of the WiFi router. The extender has two main jobs:
•The extender connects to a WiFi network that is up and running.
When the extender connects over WiFi to an existing network, it functions as a network
client, similar to how a WiFi device connects to a network.
•The extender acts as an access point for WiFi devices.
The extender has its own WiFi network that WiFi devices can join. In its role as an access
point, the extender performs tasks that WiFi routers do, such as broadcasting its network
name (SSID).
The extender must do each of these jobs so that both ends of the bridge are in place.
Existing WiFi
Sometimes your router
does not provide the WiFi
coverage you need.
WiFi Range
Extender
Boosts the range of your
existing WiFi and creates
a stronger signal in
hard-to-reach areas.
Overview
10
N600 WiFi Range Extender
Figure 4. Range extender in a home
Get Started
12
N600 WiFi Range Extender
How to Position the Extender
The ideal location to place the extender is halfway between your WiFi router and your WiFi
device.
Figure 5. Range extender location
The best connection is established with a clear line of sight between the extender and the
WiFi router and a clear line of sight between the extender and the WiFi device that you are
using. If a thick wall or other materials block this straight path, move the extender to a
different location halfway between the WiFi device and the WiFi router.
Depending on the location that you decide on, either place the extender horizontally or attach
the feet and place the extender vertically. Although the extender functions well in either
horizontal or vertical position, a horizontal position might give a better performance.
When you make the initial connection between the extender and the WiFi router, place the
extender close to the WiFi router. After you have established a connection between the
extender and the WiFi router, move the extender to the location where you intend to use it.
(You might need to unplug the extender, plug it in again at its new location, and restart it.) Use
the Link Rate LEDs on the extender to choose the location where the connection between the
extender and the WiFi router is optimal. These steps are described in detail in the sections
that describe how to connect the extender to a WiFi network.
Connect the Extender to Your WiFi Router
To connect the extender to your WiFi router and find the best location for the extender, use
one of the following methods:
•WPS. Use the extender’s WPS button to establish a WiFi connection between the
extender and the WiFi router (see Connect the Extender with WPS to a WiFi Network).
Use this method if your WiFi router supports Wi-Fi Protected Setup (WPS).
•WiFi. Use a computer or WiFi device to join the extender’s default WiFi network, then
launch a web browser to set up the connection between the extender and a WiFi network
(see Access the Extender over WiFi and Use Smart Setup). Use this method if your WiFi
router does not support WPS.
•Ethernet. Use an Ethernet cable to connect a computer to the extender, then launch a
web browser to set up the connection between the extender and a WiFi network (see
Access the Extender over Ethernet and Use Smart Setup). Use this method if you have
difficulty establishing a WiFi connection to the extender.
Get Started
13
N600 WiFi Range Extender
Connect the Extender with WPS to a WiFi Network
The easiest way to connect the extender to a WiFi network is by using Wi-Fi Protected Setup
(WPS). For this method to be successful, your WiFi router must support WPS.
If your WiFi router does not support WPS, see one of the following sections:
•Access the Extender over WiFi and Use Smart Setup on page 15
•Access the Extender over Ethernet and Use Smart Setup on page 22
WPS lets you join a secure WiFi network without typing the network name and password.
The WPS button is a physical button on the right side panel of the extender. Your WiFi router
might have a physical WPS button, a software WPS button, or both.
WPS does not support WEP network security. If you are using WEP security, follow the
instructions in Access the Extender over WiFi and Use Smart Setup on page 15.
To connect the extender with WPS to a WiFi router and find the best location for the
extender:
1. Place the extender close to the WiFi router.
Note: In a later step in this procedure, after you have established a connection
to the WiFi router, you can place the extender at its permanent location.
2. Plug the extender into an electrical outlet.
3. If necessary, press the Power button.
The power LED lights amber during startup process. After about one minute, the power
LED turns green and the startup process is complete.
You are now ready to connect the extender to your WiFi router.
4. Press the WPS button on the right side panel of the extender.
The WPS LED blinks green for two minutes.
5. Within two minutes, press the WPS button on your WiFi router.
After a few seconds, the extender connects to your existing WiFi network. Because you
placed the extender close to the WiFi router, the 2.4 GHz Link Rate LED on the extender
lights green, indicating a good connection between the WiFi router and the extender.
If the 2.4 GHz Link Rate LED does not light green, try Step 4 and Step 5 again. If it still
does not light green, see Access the Extender over WiFi and Use Smart Setup.
6. If your WiFi router supports the 5 GHz band (not all routers do), and you want to extend that
band, repeat Step 4 and Step 5 and check that the 5 GHz Link Rate LED lights green to
confirm the connection.
7. Now that the extender is connected to the WiFi router, move it to a location where you can
boost your WiFi range.
The location you choose must be within the range of your existing WiFi router network.
Get Started
14
N600 WiFi Range Extender
8. Plug the extender into an electrical outlet at the new location and restart the extender.
Unless the extender is outside the range of your WiFi router, the extender connects
automatically to the WiFi router.
The Link Rate LEDs help you choose a spot where the extender-to-router connection is
optimal. The following tables describe how the LEDs show the quality of the connection.
2.4 GHz LED Status LED Color Performance
Both the Link Rate LED and the Device
to Extender LED are green. and The extender provides the best performance.
The Link Rate LED is amber and the
Device to Extender LED is green. and The extender provides a workable performance.
The Link Rate LED is red. and The extender provides a poor performance.
The Link Rate LED is off. The extender cannot function.
5 GHz LED Status LED Color Performance
Both the Link Rate LED and the Device
to Extender LED are green. and The extender provides the best performance.
The Link Rate LED is amber and the
Device to Extender LED is green. and The extender provides a workable performance.
The Link Rate LED is red. and The extender provides a poor performance.
The Link Rate LED is off. The extender cannot function.
If the Link Rate LED is off, the extender cannot connect to the WiFi router. If the Link Rate
LED is red, the extender has a poor connection to the WiFi router.
9. If the extender has no connection or a poor connection, move the extender closer to your
WiFi router and try again until the 2.4 GHz or 5 GHz Link Rate LED is green, or at least
amber.
10. Use a WiFi network manager on the computer or mobile device to connect to the extender’s
newly created WiFi network.
By default, the extender adds _2GEXT to the end of the 2.4 GHz network name and
_5GEXT to the end of the 5 GHz network name, for example:
•Existing network name. MyNetworkName
•New extended 2.4 GHz network name. MyNetworkName_2GEXT
•New extended 5 GHz network name. MyNetworkName_5GEXT
11. Select the new network and use your WiFi router password to connect.
You are now using your extended WiFi network.
Get Started
15
N600 WiFi Range Extender
Access the Extender over WiFi and Use Smart Setup
If your WiFi router does not support WPS, access the extender over WiFi and use the
browser-based NETGEAR genie® Smart Setup to connect the extender to an existing WiFi
network.
The extender has a default NETGEAR_EXT WiFi network name (SSID) in the 2.4 GHz band
so you can access it over WiFi. After you have used Smart Setup to connect the extender to
an existing WiFi network, the extender changes its default NETGEAR_EXT network name to
the name of the existing WiFi network and adds _2GEXT to the end of the 2.4 GHz network
name and _5GEXT to the end of the 5 GHz network name, for example:
•Existing network name. MyNetworkName
•New extended 2.4 GHz network name. MyNetworkName_2GEXT
•New extended 5 GHz network name. MyNetworkName_5GEXT
To access the extender over WiFi and use Smart Setup to connect the extender to an
existing WiFi network:
1. Place the extender close to the WiFi router.
Note: In a later step in this procedure, after you have established a connection
to the WiFi router, you can place the extender at its permanent location.
2. Plug the extender into an electrical outlet.
3. If necessary, press the Power button.
The power LED lights amber during startup process. After about one minute, the power
LED turns green and the startup process is complete.
4. Make sure that your computer is not connected to an Ethernet network.
If the computer is already connected to an Ethernet network, you might not be able to
connect to the extender.
5. Open a WiFi network manager on your computer or mobile device to find and connect to the
default NETGEAR_EXT WiFi network of the extender.
Get Started
16
N600 WiFi Range Extender
You can use any WiFi network utility on a computer, tablet, or smartphone to find and
connect to the NETGEAR_EXT WiFi network of the extender. The following figure shows
an example of a WiFi network utility.
After the connection with the computer or mobile device is established, the Device to
Extender LED lights solid green.
6. Open a web browser window from the same computer or mobile device.
The browser takes you directly to the NETGEAR genie Smart Setup start screen.
Note: If you are not automatically directed to the NETGEAR genie Smart
Setup start screen, go to www.mywifiext.net, and enter admin for the
user name and password for the password.
Smart Setup searches for existing WiFi networks automatically and displays the networks
in the 2.4 GHz band.
Get Started
17
N600 WiFi Range Extender
7. Select a 2.4 GHz WiFi network to extend, and click the Continue button.
8. Enter the security settings for the existing 2.4 GHz network:
•If the network uses WPA-PSK, WPA2-PSK, or a combination of these options, do the
following:
a. In the Password (network key) field, type the network passphrase (also called
a password or network key).
b. Click the Continue button.
•If the network uses WEP, do the following:
a. From the Encryption Strength menu, select the encryption strength (64 bit or
128 bit).
b. Specify the active key by selecting the Key 1, Key 2, Key 3, or Key 4 radio
button (only one key can be the active key) and type the value for the key.
For 64-bit WEP, type 10 hexadecimal digits (any combination of 0–9, A–F). For
128-bit WEP, type 26 hexadecimal digits. The key values are not case-sensitive.
c. Click the Continue button.
Get Started
18
N600 WiFi Range Extender
If Smart Setup detects any networks in the 5 GHz band, it displays them.
9. Select a 5 GHz WiFi network to extend, and click the Continue button.
Note: If your router does not support the 5 GHz band (not all routers do) or
you want to set up the 5 GHz extender network later, click the Skip
button, and go to Step 11 on page 19.
10. Enter the security settings for the existing 5 GHz network:
•If the network uses WPA-PSK, WPA2-PSK, or a combination of these options, do the
following:
a. In the Password (network key) field, type the network passphrase (also called
a password or network key).
b. Click the Continue button.
•If the network uses WEP, do the following:
a. From the Encryption Strength menu, select the encryption strength (64 bit or
128 bit).
b. Specify the active key by selecting the Key 1, Key 2, Key 3, or Key 4 radio
button (only one key can be the active key) and type the value for the key.
For 64-bit WEP, type 10 hexadecimal digits (any combination of 0–9, A–F). For
128-bit WEP, type 26 hexadecimal digits. The key values are not case-sensitive.
c. Click the Continue button.
Get Started
19
N600 WiFi Range Extender
Smart Setup displays the network names and adds _2GEXT to the end of the 2.4 GHz
network name and _5GEXT to the end of the 5 GHz network name.
11. Use the default extension names, or, in the Name (2.4GHz SSID) field, and, if you have set
up a 5 GHz network, in the Name (5GHz SSID) field, enter new network names for your
extender WiFi networks, and click the Continue button.
Note: If you do not want to use the same security modes for your extender
networks as you use for your existing networks, clear the check box
before you click the Continue button. You then can configure the
security settings for the extender networks. However, you can also
change the security settings later.
The extender applies the settings.
12. Wait a couple of minutes while the extender creates the WiFi networks.
Get Started
20
N600 WiFi Range Extender
When the extender is ready, Smart Setup summarizes the extender networks.
13. Use a WiFi network manager on the computer or mobile device to connect to the extender’s
newly created 2.4 GHz or 5 GHz WiFi network.
Note: Unless you entered a new network name in Step 11, the extender
changes its default NETGEAR_EXT network name to the name of the
WiFi network to which you connected the extender and adds _2GEXT
to the end of the 2.4 GHz network name and _5GEXT to the end of the
5 GHz network name.
Note: If your computer or mobile device cannot join the new WiFi network of
the extender, see Improve the Connection Between the Extender and
the WiFi Router on page 83.
14. Select the My wireless devices are connected to the Extender network check box, and
click the Continue button.
Smart Setup describes the color of the Link Rate LED on the front of the extender.
Because you placed the extender close the WiFi router, the Link Rate LED is green.
Get Started
21
N600 WiFi Range Extender
15. Click the Finish button.
A pop-up screen displays.
16. To bookmark the URL of the extender, click the OK button.
17. If you are prompted to enter a user name and password, type admin for the user name and
password for the password.
The NETGEAR registration screen displays. You are now online.
18. To register the extender, enter your information in the fields onscreen and click the Register
button.
A message displays, congratulating you that you have extended your network.
19. Close your browser.
20. Now that the extender is connected to the WiFi router and you can connect a computer or
mobile device to the extender’s WiFi network, move it to a location where you can boost
your WiFi range.
The location you choose must be within the range of your existing WiFi router network.
21. Plug the extender into an electrical outlet at the new location and restart the extender.
Unless the extender is outside the range of your WiFi router, the extender connects
automatically to the WiFi router.
The Link Rate LEDs help you choose a spot where the extender-to-router connection is
optimal. The following tables describe how the LEDs show the quality of the connection.
2.4 GHz LED Status LED Color Performance
Both the Link Rate LED and the Device
to Extender LED are green. and The extender provides the best performance.
The Link Rate LED is amber and the
Device to Extender LED is green. and The extender provides a workable performance.
The Link Rate LED is red. and The extender provides a poor performance.
The Link Rate LED is off. The extender cannot function.
5 GHz LED Status LED Color Performance
Both the Link Rate LED and the Device
to Extender LED are green. and The extender provides the best performance.
The Link Rate LED is amber and the
Device to Extender LED is green. and The extender provides a workable performance.
The Link Rate LED is red. and The extender provides a poor performance.
The Link Rate LED is off. The extender cannot function.
Get Started
22
N600 WiFi Range Extender
If the Link Rate LED is off, the extender cannot connect to the WiFi router. If the Link Rate
LED is red, the extender has a poor connection to the WiFi router.
22. If the extender has no connection or a poor connection, move the extender closer to your
WiFi router and try again until the 2.4 GHz or 5 GHz Link Rate LED is green, or at least
amber.
23. Use a WiFi network manager on the computer or mobile device to reconnect to the
extender’s WiFi network.
Note: Unless you entered a new network name in Step 11, the extender
changes its default NETGEAR_EXT network name to the name of the
WiFi network to which you connected the extender and adds _2GEXT
to the end of the 2.4 GHz network name and _5GEXT to the end of the
5 GHz network name.
24. Select the new network and use your WiFi router password to connect.
You are now using your extended WiFi network.
Access the Extender over Ethernet and Use Smart Setup
If your WiFi router does not support WPS, you can use an Ethernet cable to connect your
computer to one of the LAN ports of the extender. Then use the browser-based NETGEAR
genie Smart Setup to connect the extender to an existing WiFi network.
After you have used Smart Setup to connect the extender to an existing WiFi network, the
extender changes its default NETGEAR_EXT WiFi network name (SSID) in the 2.4 GHz
band to the name of the existing WiFi network and adds _2GEXT to the end of the 2.4 GHz
network name and _5GEXT to the end of the 5 GHz network name, for example:
•Existing network name. MyNetworkName
•New extended 2.4 GHz network name. MyNetworkName_2GEXT
•New extended 5 GHz network name. MyNetworkName_5GEXT
Note: After you have set up the extender, you can also connect
Ethernet-enabled devices such as gaming consoles and printers to
the Ethernet LAN ports of the extender. For more information, see
Connect Ethernet-Enabled Devices on page 66.
To access the extender from a computer over Ethernet and use Smart Setup to
connect the extender to an existing WiFi network:
1. Place the extender close to the WiFi router.
Note: In a later step in this procedure, after you have established a connection
to the WiFi router, you can place the extender at its permanent location.
Get Started
23
N600 WiFi Range Extender
2. Plug the extender into an electrical outlet.
3. If necessary, press the Power button.
The power LED lights amber during startup process. After about one minute, the power
LED turns green and the startup process is complete.
4. Make sure that your computer is not connected to a WiFi network or Ethernet network.
If the computer is already connected to a WiFi network or Ethernet network, you might not
be able to connect to the extender.
5. Connect your computer to the extender with an Ethernet cable.
You can use any of the four Ethernet LAN ports of the extender.
CAUTION:
Do not use an Ethernet cable to connect the extender to a WiFi router. If
you do so, the extender does not work because it is designed to use only a
WiFi connection to a WiFi router.
6. If you have trouble connecting, try the following:
•Wait a couple of minutes.
If you start your computer, connect the Ethernet cable to the extender, and launch
your browser quickly, the computer might still need a couple of minutes to recognize
the Ethernet LAN connection before you can connect.
•Make sure that your Ethernet cable is securely connected to the extender and the
computer, and that the extender Device to Extender Connection LED lights.
If the LED is not lit, reconnect the Ethernet cable, and relaunch your Internet browser.
7. Open a web browser window from the same computer.
Get Started
24
N600 WiFi Range Extender
The browser takes you directly to the NETGEAR genie Smart Setup start screen.
Note: If you are not automatically directed to the NETGEAR genie Smart
Setup start screen, go to www.mywifiext.net, and enter admin for the
user name and password for the password.
Smart Setup searches for existing WiFi networks automatically and displays the networks
in the 2.4 GHz band.
8. Select a 2.4 GHz WiFi network to extend, and click the Continue button.
Get Started
25
N600 WiFi Range Extender
9. Enter the security settings for the existing 2.4 GHz network:
•If the network uses WPA-PSK, WPA2-PSK, or a combination of these options, do the
following:
a. In the Password (network key) field, type the network passphrase (also called
a password or network key).
b. Click the Continue button.
•If the network uses WEP, do the following:
a. From the Encryption Strength menu, select the encryption strength (64 bit or
128 bit).
b. Specify the active key by selecting the Key 1, Key 2, Key 3, or Key 4 radio
button (only one key can be the active key) and type the value for the key.
For 64-bit WEP, type 10 hexadecimal digits (any combination of 0–9, A–F). For
128-bit WEP, type 26 hexadecimal digits. The key values are not case-sensitive.
c. Click the Continue button.
If Smart Setup detects any networks in the 5 GHz band, it displays them.
10. Select a 5 GHz WiFi network to extend, and click the Continue button.
Note: If your router does not support the 5 GHz band (not all routers do) or
you want to set up the 5 GHz extender network later, click the Skip
button, and go to Step 12 on page 26.
Get Started
26
N600 WiFi Range Extender
11. Enter the security settings for the existing 5 GHz network:
•If the network uses WPA-PSK, WPA2-PSK, or a combination of these options, do the
following:
a. In the Password (network key) field, type the network passphrase (also called
a password or network key).
b. Click the Continue button.
•If the network uses WEP, do the following:
a. From the Encryption Strength menu, select the encryption strength (64 bit or
128 bit).
b. Specify the active key by selecting the Key 1, Key 2, Key 3, or Key 4 radio
button (only one key can be the active key) and type the value for the key.
For 64-bit WEP, type 10 hexadecimal digits (any combination of 0–9, A–F). For
128-bit WEP, type 26 hexadecimal digits. The key values are not case-sensitive.
c. Click the Continue button.
Smart Setup displays the network names and adds _2GEXT to the end of the 2.4 GHz
network name and _5GEXT to the end of the 5 GHz network name.
12. Use the default extension names, or, in the Name (2.4GHz SSID) field, and, if you have set
up a 5 GHz network, in the Name (5GHz SSID) field, enter new network names for your
extender WiFi networks, and click the Continue button.
Note: If you do not want to use the same security modes for your extender
networks as you use for your existing networks, clear the check box
before you click the Continue button. You then can configure the
security settings for the extender networks. However, you can also
change the security settings later.
Get Started
27
N600 WiFi Range Extender
The extender applies the settings.
13. Wait a couple of minutes while the extender creates the WiFi networks.
When the extender is ready, Smart Setup summarizes the extender networks.
14. Use a WiFi network manager on the computer or mobile device to connect to the extender’ s
newly created 2.4 GHz or 5 GHz WiFi network.
Note: Unless you entered a new network name in Step 12, the extender
changes its default NETGEAR_EXT network name to the name of the
WiFi network to which you connected the extender and adds _2GEXT
to the end of the 2.4 GHz network name and _5GEXT to the end of the
5 GHz network name.
Note: If your computer or mobile device cannot join the new WiFi network of
the extender, see Improve the Connection Between the Extender and
the WiFi Router on page 83.
15. Select the My wireless devices are connected to the Extender network check box, and
click the Continue button.
Get Started
28
N600 WiFi Range Extender
Smart Setup describes the color of the Link Rate LED on the front of the extender.
Because you placed the extender close the WiFi router, the Link Rate LED is green.
16. Click the Finish button.
A pop-up screen displays.
17. To bookmark the URL of the extender, click the OK button.
18. If you are prompted to enter a user name and password, type admin for the user name and
password for the password.
The NETGEAR registration screen displays. You are now online.
19. To register the extender, enter your information in the fields onscreen and click the Register
button.
A message displays, congratulating you that you have extended your network.
20. Close your browser.
21. Disconnect the Ethernet cable from the computer and the extender.
22. Now that the extender is connected to the WiFi router and you can connect a computer or
mobile device to the extender’s WiFi network, move it to a location where you can boost
your WiFi range.
The location you choose must be within the range of your existing WiFi router network.
23. Plug the extender into an electrical outlet at the new location and restart the extender.
Unless the extender is outside the range of your WiFi router, the extender connects
automatically to the WiFi router.
The Link Rate LEDs help you choose a spot where the extender-to-router connection is
optimal. The following tables describe how the LEDs show the quality of the connection.
2.4 GHz LED Status LED Color Performance
Both the Link Rate LED and the Device
to Extender LED are green. and The extender provides the best performance.
The Link Rate LED is amber and the
Device to Extender LED is green. and The extender provides a workable performance.
Get Started
29
N600 WiFi Range Extender
If the Link Rate LED is off, the extender cannot connect to the WiFi router. If the Link Rate
LED is red, the extender has a poor connection to the WiFi router.
24. If the extender has no connection or a poor connection, move the extender closer to your
WiFi router and try again until the 2.4 GHz or 5 GHz Link Rate LED is green, or at least
amber.
25. Use a WiFi network manager on the computer or mobile device to reconnect to the
extender’s WiFi network.
Note: Unless you entered a new network name in Step 12, the extender
changes its default NETGEAR_EXT network name to the name of the
WiFi network to which you connected the extender and adds _2GEXT
to the end of the 2.4 GHz network name and _5GEXT to the end of the
5 GHz network name.
26. Select the new network and use your WiFi router password to connect.
You are now using your extended WiFi network.
The Link Rate LED is red. and The extender provides a poor performance.
The Link Rate LED is off. The extender cannot function.
5 GHz LED Status LED Color Performance
Both the Link Rate LED and the Device
to Extender LED are green. and The extender provides the best performance.
The Link Rate LED is amber and the
Device to Extender LED is green. and The extender provides a workable performance.
The Link Rate LED is red. and The extender provides a poor performance.
The Link Rate LED is off. The extender cannot function.
2.4 GHz LED Status LED Color Performance
30
3
3. Manage the Extender Network and
Security Settings
This chapter covers the following topics:
•Log In to the Extender After Initial Setup
•Change the Password
•Connect the Extender to a WiFi Network Without Using Smart Setup
•Connect the Extender to a Hidden WiFi Network
•Use WPS to Add a Device to the Extender’s WiFi Network
•Manage the Extender WiFi Settings
•Change the Extender IP Address
•Manage Advanced WiFi and WPS Settings
•Manage a WiFi Access List
•Set the Operating Mode to FastLane Technology
•Run Smart Setup Again After Initial Setup
•Connect Ethernet-Enabled Devices
Manage the Extender Network and Security Settings
31
N600 WiFi Range Extender
Log In to the Extender After Initial Setup
You can log in to the extender to view or change the extender’s settings.
If you connect to the extender before it has been set up, the browser automatically goes to
http://www.mywifiext.net and displays the NETGEAR genie Smart Setup screens, which step
you through the setup process. For more information, see Access the Extender over WiFi
and Use Smart Setup on page 15 or Access the Extender over Ethernet and Use Smart
Setup on page 22.
To log in to the extender after initial setup:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and password for the password.
Note: NETGEAR recommends that you set a more secure password after you
log in. For more information, see Change the Password on page 33.
The Status screen displays (see the following figure). Menu selections display on the left.
The Status screen shows the current settings for the extender. The firmware version
displays below the language menu.
For more information about the Status screen, see View the Status and Traffic Statistics
of the Extender on page 74.
For information about upgrading firmware, see Update the Firmware on page 73.
4. To change your language, select a language from the menu in the top right of the screen.
By default, the language selection is Auto, which means that the extender uses the
language that it detects from the browser that you use.
Manage the Extender Network and Security Settings
32
N600 WiFi Range Extender
Manage the Extender Network and Security Settings
33
N600 WiFi Range Extender
Change the Password
The user name to access the extender is admin, and its default password is password.
NETGEAR strongly recommends that you set a more secure password.
To change the password for the extender:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and password for the password.
If you already changed the password and want to change it again, type your personalized
password.
4. Select Maintenance > Set Password.
5. Type the old password.
6. Type the new password twice.
7. Click the Apply button.
Your settings are saved.
Connect the Extender to a WiFi Network Without Using
Smart Setup
If you want to change the extender connection to another WiFi network, you can do so
without using NETGEAR genie Smart Setup.
Note: You cannot use the following procedure to change the network names
or security options for your extender WiFi networks. For information
about how to change these settings, see Manage the Extender WiFi
Settings on page 43.
Manage the Extender Network and Security Settings
34
N600 WiFi Range Extender
To change the extender connection to another WiFi network without using Smart
Setup:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
4. Select Settings > Connect to Existing Network.
The extender scans for existing WiFi networks and displays the networks in the 2.4 GHz
band.
If your WiFi network is functioning but not on the list, your WiFi network might be hidden,
or the connection between the WiFi router and the extender might be poor. For more
information, see the following sections:
•Connect the Extender to a Hidden WiFi Network on page 37
•Improve the Connection Between the Extender and the WiFi Router on page 83
Manage the Extender Network and Security Settings
35
N600 WiFi Range Extender
5. Select the radio button for the 2.4 GHz network to which you want to connect the extender,
and click the Continue button.
6. Enter the security settings for the existing 2.4 GHz network:
•If the network uses WPA-PSK, WPA2-PSK, or a combination of these options, do the
following:
a. In the Password (network key) field, type the network passphrase (also called
a password or network key).
b. Click the Continue button.
•If the network uses WEP, do the following:
a. From the Encryption Strength menu, select the encryption strength (64 bit or
128 bit).
b. Specify the active key by selecting the Key 1, Key 2, Key 3, or Key 4 radio
button (only one key can be the active key) and type the value for the key.
For 64-bit WEP, type 10 hexadecimal digits (any combination of 0–9, A–F). For
128-bit WEP, type 26 hexadecimal digits. The key values are not case-sensitive.
c. Click the Continue button.
If the extender detects any networks in the 5 GHz band, it displays them.
If your WiFi network is functioning but not on the list, your WiFi network might be hidden,
or the connection between the WiFi router and the extender might be poor. For more
information, see the following sections:
•Connect the Extender to a Hidden WiFi Network on page 37
•Improve the Connection Between the Extender and the WiFi Router on page 83
7. Select the radio button for the 5 GHz network to which you want to connect the extender,
and click the Continue button.
Manage the Extender Network and Security Settings
36
N600 WiFi Range Extender
Note: If your router does not support the 5 GHz band (not all routers do) or
you do not yet want to change the 5 GHz network to which the extender
connects, click the Skip button, and go to Step 9 on page 65.
8. Enter the security settings for the existing 5 GHz network:
•If the network uses WPA-PSK, WPA2-PSK, or a combination of these options, do the
following:
a. In the Password (network key) field, type the network passphrase (also called
a password or network key).
b. Click the Continue button.
•If the network uses WEP, do the following:
a. From the Encryption Strength menu, select the encryption strength (64 bit or
128 bit).
b. Specify the active key by selecting the Key 1, Key 2, Key 3, or Key 4 radio
button (only one key can be the active key) and type the value for the key.
For 64-bit WEP, type 10 hexadecimal digits (any combination of 0–9, A–F). For
128-bit WEP, type 26 hexadecimal digits. The key values are not case-sensitive.
c. Click the Continue button.
9. Wait about two minutes while the extender changes the WiFi network or networks.
10. Use a WiFi network manager on the computer or on a mobile device to reconnect to the
extender’s WiFi network.
Manage the Extender Network and Security Settings
37
N600 WiFi Range Extender
Note: If your computer or mobile device cannot join the new WiFi network of
the extender, see You Cannot Join a WiFi Network and Receive an
Error Message on page 82.
11. Click the I have connected to the Extender network button.
The WiFi network settings for the extender are saved and the Status screen displays.
Connect the Extender to a Hidden WiFi Network
You can manually connect the extender to a hidden WiFi network without using NETGEAR
genie Smart Setup.
Before you start the following procedure, you must know the name of the hidden WiFi
network, the type of security that the network uses, and the key or passphrase to connect to
the network.
Note: You cannot use the following procedure to change the network names
or security options for your extender WiFi networks. For information
about how to change these settings, see Manage the Extender WiFi
Settings on page 43.
To connect the extender to a hidden WiFi network without using Smart Setup:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
4. Select Settings > Connect to Existing Network.
Manage the Extender Network and Security Settings
38
N600 WiFi Range Extender
The extender scans for existing WiFi networks and displays the networks in the 2.4 GHz
band.
5. Select the Manually input my wireless SSID radio button and click the Continue button.
The screen adjusts.
6. In the Name (SSID) field, enter the name of the 2.4 GHz network to which you want to
connect the extender.
7. From the Security menu, select the security setting for the 2.4 GHz network.
The screen adjusts.
8. Enter the security settings for the 2.4 GHz network:
•If the network uses WPA-PSK, WPA2-PSK, or a combination of these options, do the
following:
a. In the Password (network key) field, type the network passphrase (also called
a password or network key).
b. Click the Continue button.
Manage the Extender Network and Security Settings
39
N600 WiFi Range Extender
•If the network uses WEP, do the following:
a. From the Encryption Strength menu, select the encryption strength (64 bit or
128 bit).
b. Specify the active key by selecting the Key 1, Key 2, Key 3, or Key 4 radio
button (only one key can be the active key) and type the value for the key.
For 64-bit WEP, type 10 hexadecimal digits (any combination of 0–9, A–F). For
128-bit WEP, type 26 hexadecimal digits. The key values are not case-sensitive.
c. Click the Continue button.
If the extender detects any networks in the 5 GHz band, it displays them.
9. Select the Manually input my wireless SSID radio button and click the Continue button.
Note: If your router does not support the 5 GHz band (not all routers do) or
you do not want to connect the extender to a hidden 5 GHz network,
click the Skip button, and go to Step 13 on page 40.
The screen adjusts.
10. In the Name (SSID) field, enter the name of the 5 GHz network to which you want to
connect the extender.
11. From the Security menu, select the security setting for the 5 GHz network.
The screen adjusts.
12. Enter the security settings for the 5 GHz network:
•If the network uses WPA-PSK, WPA2-PSK, or a combination of these options, do the
following:
a. In the Password (network key) field, type the network passphrase (also called
a password or network key).
b. Click the Continue button.
Manage the Extender Network and Security Settings
40
N600 WiFi Range Extender
•If the network uses WEP, do the following:
a. From the Encryption Strength menu, select the encryption strength (64 bit or
128 bit).
b. Specify the active key by selecting the Key 1, Key 2, Key 3, or Key 4 radio
button (only one key can be the active key) and type the value for the key.
For 64-bit WEP, type 10 hexadecimal digits (any combination of 0–9, A–F). For
128-bit WEP, type 26 hexadecimal digits. The key values are not case-sensitive.
c. Click the Continue button.
13. Wait about two minutes while the extender connects to the hidden WiFi network or networks.
14. Use a WiFi network manager on the computer or on a mobile device to reconnect to the
extender’s WiFi network.
Note: If your computer or mobile device cannot join the new WiFi network of
the extender, see You Cannot Join a WiFi Network and Receive an
Error Message on page 82.
15. Click the I have connected to the Extender network button.
The WiFi network settings for the extender are saved and the Status screen displays.
Use WPS to Add a Device to the Extender’s WiFi Network
WPS (Wi-Fi Protected Setup) lets you connect a computer or WiFi device to the extender’s
network without entering the WiFi network passphrase or key. Instead, you use a WPS button
or enter a PIN to connect.
If you use the Push Button method, the WiFi device that you are trying to connect must have
a physical push button or a software push button. If you use the PIN method, you must know
the PIN of the WiFi device that you are trying to connect.
WPS supports WPA and WPA2 WiFi security. If your extender network is open (no WiFi
security is set), connecting with WPS automatically sets WPA + WPA2 WiFi security on the
extender network and generates a random passphrase. You can view this passphrase on the
Manage the Extender Network and Security Settings
41
N600 WiFi Range Extender
Wireless Settings screen (for more information, see Manage the Extender WiFi Settings on
page 43).
Note: For information about using WPS to connect the extender to a WiFi
network during setup, see Connect the Extender with WPS to a WiFi
Network on page 13.
Use WPS with the Push Button Method
To use the Push Button method to connect a WiFi device to the extender’s WiFi network, the
WiFi device that you are trying to connect must have a physical push button or a software
push button.
To let a WiFi device join the extender’s WiFi network using WPS with the Push Button
method:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
4. Select Add WPS Client.
The screen displays a description of the WPS method.
5. Click the Next button.
By default, the Push Button (recommended) radio button is selected.
6. Either click the button onscreen or press the WPS button on the right side panel of the
extender.
Both Link Rate LEDs and the Device to Extender LED blink green for two
minutes.
Manage the Extender Network and Security Settings
42
N600 WiFi Range Extender
For two minutes, the extender attempts to find the WiFi device (that is, the client) that you
want to join the extender’s WiFi network.
7. Within two minutes, go to the WiFi device and press its WPS button (to join the extender’s
WiFi network without entering a password.
8. To verify that the WiFi device is connected to the extender’s WiFi network, select
Maintenance > Attached Devices.
The WiFi device displays onscreen.
Use WPS with the PIN Method
To use the PIN method to connect a WiFi device to the extender’s WiFi network, you must
know the PIN of the WiFi device that you are trying to connect.
To let a WiFi device join the extender’s WiFi network using WPS with the PIN method:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
4. Select Add WPS Client.
The screen displays a description of the WPS method.
5. Click the Next button.
On the screen that displays, the Push Button (recommended) radio button is selected
by default.
6. Select the PIN Number radio button.
7. In the Enter Client's PIN field, enter the PIN number of the WiFi device.
8. Click the Next button.
Manage the Extender Network and Security Settings
43
N600 WiFi Range Extender
For four minutes, the extender attempts to find the WiFi device (that is, the client) that you
want to join the extender’s WiFi network.
9. Within four minutes, go to the WiFi device and use its WPS software to join the network
without entering a password.
10. To verify that the WiFi device is connected to the extender’s WiFi network, select
Maintenance > Attached Devices.
The WiFi device displays onscreen.
Manage the Extender WiFi Settings
You can change the network name (SSID) for the extender’s network and set up WiFi
security. If you did not change these settings already during initial setup, the network name is
NETGEAR_EXT, and the network is open (no WiFi security is set up).
Note: Although the WiFi security of the extender’s network can be different
from the WiFi security of the network that the extender is connected
to, you typically would select the same type of WiFi security for both
networks.
In some regions, not all channels are available. Do not change the channel unless you
experience interference (shown by lost connections or slow data transfers). If this happens,
experiment with different channels to see which is the best.
When you use more than one WiFi router or access point, it is better if adjacent routers or
access points use different channels to reduce interference. NETGEAR recommends a
channel spacing of four channels between adjacent routers or access points (for example,
use Channels 1 and 5, or 6 and 10).
Note: You can change the channel only if you have enabled FastLane
Technology or if the extender is not connected to the WiFi router. For
more information, see Set the Operating Mode to FastLane Technology
on page 61. When the extender is in normal operating mode (also
referred to as Internet Surfing mode), you cannot change the channel.
Manage the Extender Network and Security Settings
44
N600 WiFi Range Extender
Note: You can change the wireless mode in one radio band only if the
extender is connected to the WiFi router in the other radio band. For
example, you can change the wireless mode in the 2.4 GHz band only
if the extender is connected to the WiFi router in the 5 GHz band. If
the extender is connected to the WiFi router in the 2.4 GHz band, you
cannot change the wireless mode in the 2.4 GHz band because the
extender adopts the wireless mode that the WiFi router functions in.
To change the WiFi settings for the extender’s network:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
4. Select Setting > Wireless.
Manage the Extender Network and Security Settings
45
N600 WiFi Range Extender
5. Change the WiFi settings as described in the following table:
Setting Description
Region Selection
Region From the Region menu, select the region in which you operate the extender.
Note: If you purchased the extender in the United States or Canada, the selection
from the Region menu is North America. You cannot change this selection.
Ethernet ports to WiFi
use the following band Specify if the Ethernet ports on the rear panel of the extender connect to the
2.4 GHz band or the 5 GHz band by selecting one of the following radio buttons:
• 2.4GHz. The Ethernet ports connect to the 2.4 GHz WiFi band. This is the
default setting.
• 5GHz. The Ethernet ports connect to the 5 GHz WiFi band.
My WN2500RPv2 wireless network (2.4GHz)
Name (SSID) In the Name (SSID) field, type a new name or use the name that the extender
assigns by default:
• Existing network name. MyNetworkName
• New extended 2.4 GHz network name. MyNetworkName_2GEXT
If more than one extender operates in your neighborhood, changing the SSID
makes it easier to identify the extenders.
Channel From the Channel menu, select Auto for automatic channel selection or select an
individual channel.
Note: You can change the channel if you have enabled FastLane Technology or
if the extender is not connected to the WiFi router. For more information about
FastLane Technology, see Set the Operating Mode to FastLane Technology on
page 61.
Note: In some regions, not all channels are available. Do not change the channel
unless you experience interference (shown by lost connections or slow data
transfers). If this happens, experiment with different channels to see which is the
best.
Manage the Extender Network and Security Settings
46
N600 WiFi Range Extender
Wireless mode From the Wireless mode menu, select one of the following modes:
• Up to 54 Mbps. Legacy mode. This mode allows 802.11n, 802.11g, and
802.11b devices to join the network but limits 802.11n devices to function at
up to 54 Mbps. If your network security is WEP or WPA-PSK [TKIP], you must
use the Up to 54 Mbps mode.
• Up to 145 Mbps. Neighbor-friendly mode for reduced interference with
neighboring wireless networks. This mode allows 802.11n, 802.11g, and
802.11b devices to join the network but limits 802.11n devices to function at
up to 145 Mbps.
• Up to 300 Mbps. Performance mode. This mode allows 802.11n, 802.11g,
and 802.11b devices to join the network and allows 802.11n devices to
function at up to 300 Mbps.
Note: You can change the wireless mode in the 2.4 GHz band only if the extender
is connected to the WiFi router in the 5 GHz band. If the extender is connected to
the WiFi router in the 2.4 GHz band, the extender adopts the wireless mode that
the WiFi router functions in and the Wireless mode menu is disabled.
Note: WPA-PSK [TKIP] security supports speeds of up to 54 Mbps. Even if your
devices are capable of a higher speed, WPA-PSK [TKIP] security limits their speed
to 54 Mbps.
Note: To enable the extender to function at full link rate, enable FastLane
Technology or disable 20/40 MHz coexistence. For more information about
FastLane Technology, see Set the Operating Mode to FastLane Technology on
page 61. For more information about disabling 20/40 MHz coexistence, see
Manage Advanced WiFi and WPS Settings on page 53. Disable 20/40 MHz
coexistence only if no other wireless networks are present in your environment.
Security Options (2.4GHz)
Select the type of WiFi security that you want to use for the extender’s 2.4 GHz WiFi network:
• None. An open WiFi network that does not provide any security. Any WiFi device can join the network.
• WEP. WEP is an older standard, and is less secure than WPA or WPA2. WEP limits the wireless mode
to Up to 54 Mbps. WEP uses encryption keys and data encryption for data security. Select 64-bit or
128-bit encryption and enter a key. To join the extender’s WiFi network, a user must enter the key. For
more information, see Configure WEP on page 50.
• WPA-PSK [TKIP]. WPA is more secure than WEP. Enter a passphrase. For more information, see
Configure WPA, WPA2, or WPA + WPA2 on page 49.
• WPA2-PSK [AES]. WPA2 is even more secure than WEP, but some older WiFi devices do not detect
WPA2. Enter a passphrase. To join the extender’s WiFi network, a user must enter the passphrase. For
more information, see Configure WPA, WPA2, or WPA + WPA2 on page 49.
• WPA-PSK [TKIP] + WPA2-PASK [AES]. When your network includes WiFi devices that support either
WPA or WPA2, select WPA-PSK [TKIP] + WPA2-PASK [AES] security. Enter a passphrase. To join the
extender’s WiFi network, a user must enter the passphrase. For more information, see Configure WPA,
WPA2, or WPA + WPA2 on page 49.
Setting Description
Manage the Extender Network and Security Settings
47
N600 WiFi Range Extender
My WN2500RPv2 wireless network (5GHz)
Name (SSID) In the Name (SSID) field, type a new name or use the name that the extender
assigns by default:
• Existing network name. MyNetworkName
• New extended 5 GHz network name. MyNetworkName_5GEXT
If more than one extender operates in your neighborhood, changing the SSID
makes it easier to identify the extenders.
Channel From the Channel menu, select Auto for automatic channel selection or select an
individual channel.
Note: You can change the channel if you have enabled FastLane Technology or
if the extender is not connected to the WiFi router. For more information about
FastLane Technology, see Set the Operating Mode to FastLane Technology on
page 61.
Note: In some regions, not all channels are available. Do not change the channel
unless you experience interference (shown by lost connections or slow data
transfers). If this happens, experiment with different channels to see which is the
best.
Wireless mode From the Wireless mode menu, select one of the following modes:
• Up to 54 Mbps. Legacy mode. This mode allows 802.11an and 802.11a
devices to join the network but limits 802.11n devices to function at up to
54 Mbps. If your network security is WEP or WPA-PSK [TKIP], you must use
the Up to 54 Mbps mode.
• Up to 145 Mbps. Neighbor-friendly mode for reduced interference with
neighboring wireless networks. Allows 802.11an and 802.11a devices to join
the network but limits 802.11an devices to function at up to 145 Mbps.
• Up to 300 Mbps. Performance mode. Allows 802.11an and 802.11a devices
to join the network and allows 802.11an devices to function at up to
300 Mbps.
Note: You can change the wireless mode in the 5 GHz band only if the extender
is connected to the WiFi router in the 2.4 GHz band. If the extender is connected
to the WiFi router in the 5 GHz band, the extender adopts the wireless mode that
the WiFi router functions in and the Wireless mode menu is disabled.
Note: To enable the extender to function at full link rate, enable FastLane
Technology. For more information, see Set the Operating Mode to FastLane
Technology on page 61.
Note: WPA-PSK [TKIP] security supports speeds of up to 54 Mbps. Even if your
devices are capable of a higher speed, WPA-PSK [TKIP] security limits their speed
to 54 Mbps.
Setting Description
Manage the Extender Network and Security Settings
48
N600 WiFi Range Extender
CAUTION:
If you use a WiFi device to change the extender’s WiFi settings, you are
disconnected when you click the Apply button. To reconnect, you must
select the new network name that you created, and enter the passphrase
or WiFi security key that you set up.
6. Click the Apply button.
The extender applies your settings, which might take up to one minute.
7. If you are disconnected, reconnect your WiFi device to the extender’s network with its new
settings.
Use a WiFi network manager on the computer or on a mobile device to reconnect to the
extender’s WiFi network.
Note: If your computer or mobile device cannot join the new WiFi network of
the extender, see You Cannot Join a WiFi Network and Receive an
Error Message on page 82.
8. Click the I have connected to the Extender network button.
The WiFi network settings for the extender are saved and the Status screen displays.
Security Options (5GHz)
Select the type of WiFi security that you want to use for the extender’s 5 GHz WiFi network:
• None. An open WiFi network that does not provide any security. Any WiFi device can join the network.
• WEP. WEP is an older standard, and is less secure than WPA or WPA2. WEP limits the wireless mode
to Up to 54 Mbps. WEP uses encryption keys and data encryption for data security. Select 64-bit or
128-bit encryption and enter a key. To join the extender’s WiFi network, a user must enter the key. For
more information, see Configure WEP on page 50.
• WPA-PSK [TKIP]. WPA is more secure than WEP. Enter a passphrase. For more information, see
Configure WPA, WPA2, or WPA + WPA2 on page 49.
• WPA2-PSK [AES]. WPA2 is even more secure than WEP, but some older WiFi devices do not detect
WPA2. Enter a passphrase. To join the extender’s WiFi network, a user must enter the passphrase. For
more information, see Configure WPA, WPA2, or WPA + WPA2 on page 49.
• WPA-PSK [TKIP] + WPA2-PASK [AES]. When your network includes WiFi devices that support either
WPA or WPA2, select WPA-PSK [TKIP] + WPA2-PASK [AES] security. Enter a passphrase. To join
the extender’s WiFi network, a user must enter the passphrase. For more information, see Configure
WPA, WPA2, or WPA + WPA2 on page 49.
Setting Description
Manage the Extender Network and Security Settings
49
N600 WiFi Range Extender
Configure WPA, WPA2, or WPA + WPA2
Both WPA and WPA2 provide strong data security. WPA2 with AES is a hardware
implementation. If you want to use WPA2 security, make sure that all devices in your WiFi
network support WPA2 security. If you are not sure, use WPA + WPA2 security.
Note: WPA-PSK [TKIP] security supports speeds of up to 54 Mbps. Even if
your devices are capable of a higher speed, WPA-PSK [TKIP] security
limits their speed to 54 Mbps. NETGEAR recommends that you use
WPA2-PSK security, which supports the maximum speed that your
devices are capable of.
The process to configure WPA, WPA2, or WPA + WPA2 security is the same for the 2.4 GHz
and 5 GHz bands.
To configure WPA, WPA2, or WPA + WPA2 in the extender:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
4. Select Settings > Wireless.
5. Scroll down to either the Security Options (2.4GHz) section (shown in the previous figure) or
the Security Options (5GHz) section and select the WPA-PSK [TKIP], WPA2-PSK [AES], or
WPA-PSK [TKIP] + WPA2-PSK [AES] radio button.
Manage the Extender Network and Security Settings
50
N600 WiFi Range Extender
6. In the PassPhrase field, enter the passphrase.
7. Click the Apply button.
Your settings are saved.
8. If you are disconnected, reconnect your WiFi device to the extender’s network with its new
settings.
Smart Setup can guide you through this process. For more information, see Run Smart
Setup Again After Initial Setup on page 63.
Configure WEP
WEP is legacy WiFi security that limits the wireless mode to the Up to 54 Mbps selection,
irrespective of whether you use the 2.4 GHz band or the 5 GHz band. Unless your WiFi
network includes devices that do not support WPA2 or WPA security, NETGEAR
recommends that you use WPA2 or WPA + WPA2 security.
Note: 802.11n devices do not support WEP security. If you change the
security to WEP, 802.11n devices in either the 2.4 GHz or 5 GHz band
cannot join the network.
Note: WPS does not support WEP security. If you change the security to
WEP, you can no longer let WiFi devices join the extender’s WiFi
network by using WPS.
The process to configure WEP security is the same for the 2.4 GHz and 5 GHz bands.
To set up WEP:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
4. Select Settings > Wireless.
Manage the Extender Network and Security Settings
51
N600 WiFi Range Extender
5. Scroll down to either the Security Options (2.4GHz) section (shown in the following figure) or
the Security Options (5GHz) section and select the WEP radio button.
6. From the Encryption Strength menu, select the encryption strength setting:
•64 bit. Requires an encryption key of 10 hexadecimal digits (any combination of 0–9,
a–f, or A–F) or a string of five characters.
•128 bit. Requires an encryption key of 26 hexadecimal digits (any combination of
0–9, a–f, or A–F) or a string of 13 characters.
7. Specify the active key by selecting the Key 1, Key 2, Key 3, or Key 4 radio button.
Only one key can be the active key.
8. Enter the value for the key:
•For 64-bit WEP, type 10 hexadecimal digits (any combination of 0–9, A–F). The key
values are not case-sensitive.
•For 128-bit WEP, type 26 hexadecimal digits (any combination of 0–9, A–F). The key
values are not case-sensitive.
9. Click the Apply button.
Your settings are saved.
10. If you are disconnected, reconnect your WiFi device to the extender’s network with its new
settings.
Smart Setup can guide you through this process. For more information, see Run Smart
Setup Again After Initial Setup on page 63.
Manage the Extender Network and Security Settings
52
N600 WiFi Range Extender
Change the Extender IP Address
By default, the extender receives its IP address automatically from the WiFi router to which it
connects. If the WiFi router does not have a DHCP server or its DHCP server is disabled, you
can assign a static IP address to the extender.
Before you assign a static IP address, you must know the IP address range, subnet mask,
gateway IP address, and primary DNS server of your network.
CAUTION:
NETGEAR recommends that you change the IP address of the extender
only if you are technically experienced or have a technically experienced
person to help you. Incorrect configuration can prevent you from
connecting to the extender and might require you to reset the extender to
factory default settings.
To change the IP address of the extender to a static IP address:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
4. Select extender Settings > IP Address.
5. Select the Use Static IP Address radio button.
6. Specify the static IP address settings:
•IP Address. The static IP address to be assigned to the extender.
•IP Subnet Mask. The subnet mask associated with the IP address.
•Gateway IP Address. The IP address for the gateway for your WiFi network.
•Primary DNS. The primary domain name server (DNS) for your WiFi network.
Manage the Extender Network and Security Settings
53
N600 WiFi Range Extender
7. Click the Apply button.
Your settings are saved, and you are disconnected from the extender.
8. To continue to configure the extender, reconnect to the extender using the new IP address.
Manage Advanced WiFi and WPS Settings
The extender is already configured with the optimum settings. Do not change the advanced
settings unless directed by NETGEAR support. Incorrect settings might disable the extender
unexpectedly.
To view or change the advanced WiFi and WPS settings:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
4. Select Advanced > Wireless Settings.
5. View or change the following settings as described in the following table:
Setting Description
Advanced Wireless Settings
Enable Wireless
Access Point (2.4GHz) By default, the extender functions as a WiFi access point in the 2.4 GHz band.
Clear the Enable Wireless Access Point (2.4GHz) check box only if you want to
prevent WiFi devices from connecting to the extender in the 2.4 GHz band. LAN
devices can still connect to the extender over an Ethernet cable.
Manage the Extender Network and Security Settings
54
N600 WiFi Range Extender
Note: If you clear a Keep Existing Wireless Settings check box and use
WPS to add a computer or WiFi device to the extender’s network, the
SSID and passphrase are automatically generated and other devices
that are already connected to the extender’s network might be
disconnected. You can view the SSID and passphrase on the Wireless
Settings screen (see Manage the Extender WiFi Settings on page 43).
NETGEAR recommends that you keep the Keep Existing Wireless
Settings check boxes selected.
6. Click the Apply button.
Your changes are saved.
Enable SSID
Broadcast (2.4GHz) By default, the extender broadcasts its WiFi network name (SSID) for the 2.4 GHz
band. Clear the Enable SSID Broadcast (2.4GHz) check box only to hide the
network name of the extender in the 2.4 GHz band. In such a situation, the
network name of the extender does not display in a WiFi network manager. A user
who wants to join the hidden WiFi network of the extender must know its network
name.
Enable 20/40 MHz
Coexistence (2.4GHz) By default, 20/40 MHz coexistence is enabled to prevent interference between
wireless networks in your environment at the expense of the wireless speed. If no
other wireless networks are present in your environment, you can clear the
Enable 20/40 MHz Coexistence check box to increase the wireless speed to the
maximum supported speed.
Enable Wireless
Access Point (5GHz) By default, the extender functions as a WiFi access point in the 5 GHz band. Clear
the Enable W ireless Access Point (5GHz) check box only if you want to prevent
WiFi devices from connecting to the extender in the 5 GHz band. LAN devices can
still connect to the extender over an Ethernet cable.
Enable SSID
Broadcast (5GHz) By default, the extender broadcasts its WiFi network name (SSID) for the 5 GHz
band. Clear the Enable SSID Broadcast (5GHz) check box only to hide the
network name of the extender in the 5 GHz band. In such a situation, the network
name of the extender does not display in a WiFi network manager. A user who
wants to join the hidden WiFi network of the extender must know its network
name.
WPS Settings
Keep Existing Wireless
Settings (2.4GHz b/g/n) By default, the settings on the Wireless Settings screen remain the same when
you use WPS to establish a WiFi connection in the 2.4 GHz band. Clear the Keep
Existing Wireless Settings (2.4GHz b/g/n) check box only if you want to allow
the WPS process to change the SSID and passphrase for access in the 2.4 GHz
band on the Wireless Settings screen.
Keep Existing Wireless
Settings (5GHz a/n) By default, the settings on the Wireless Settings screen remain the same when
you use WPS to establish a WiFi connection in the 5 GHz band. Clear the Keep
Existing Wireless Settings (5GHz a/n) check box only if you want to allow the
WPS process to change the SSID and passphrase for access in the 5 GHz band
on the Wireless Settings screen.
Setting Description
Manage the Extender Network and Security Settings
55
N600 WiFi Range Extender
Manage a WiFi Access List
By default, any WiFi device that is configured with the correct network name (SSID) can
access the WiFi network of the extender. For increased security, you can restrict access to
the WiFi network of the extender to allow only specific WiFi devices based on their MAC
addresses. Devices that are not on the access list cannot join the WiFi network of the
extender.
Each network device has a MAC address, which is a unique 12-character physical address,
containing the hexadecimal characters 0–9, a–f, or A–F only, and separated by colons (for
example, 00:09:AB:CD:EF:01). Typically, the MAC address is on the label of the WiFi device.
If you do not have access to the label, you can display the MAC address using the network
configuration utilities of the computer. You might also find the MAC addresses on the
Network Devices screen (see View the Wired and WiFi Network Devices on page 78).
CAUTION:
If you use a WiFi device to set up the access list, add your WiFi device to
the access list. Otherwise, you are disconnected when you click the Apply
button. To avoid this situation, use a computer with a wired connection to
access the extender.
Set Up and Enable the Access List
Before you can enable the access list, you must add the MAC addresses of the WiFi devices
that you want to grant access to the WiFi network of the extender.
To set up and enable the access list:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
Manage the Extender Network and Security Settings
56
N600 WiFi Range Extender
4. Select Advanced > Wireless Settings.
5. Click the Setup Access List button.
If you have not yet added any WiFi devices, the Wireless Card Access List is empty.
6. Click the Add button.
The Available Wireless Cards table displays the name and MAC address of WiFi devices
that are connected to the extender.
7. Select a device by one of the following methods:
•Select a device from the table by selecting its associated radio button.
The Device Name and MAC Address fields are automatically populated.
•Enter a device name and MAC address manually:
a. In the Device Name field, type a name for the WiFi device.
b. In the MAC Address field, type the MAC address of the WiFi device.
Manage the Extender Network and Security Settings
57
N600 WiFi Range Extender
8. Click the Apply button.
The WiFi device is added to the Wireless Card Access List.
9. To add more WiFi devices, repeat Step 6 through Step 8.
10. Select the Turn Access Control On check box.
CAUTION:
If you use a WiFi device to set up the access list, add your WiFi device to
the access list. Otherwise, you are disconnected when you click the Apply
button.
11. Click the Apply button.
Now only WiFi devices that are in the Wireless Card Access List can access the WiFi
network of the extender.
Disable the Access List
If you decide that you no longer need an access list on the extender, you can disable the
access list.
To disable the access list:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
Manage the Extender Network and Security Settings
58
N600 WiFi Range Extender
4. Select Advanced > Wireless Settings.
5. Click the Setup Access List button.
6. Clear the Turn Access Control On check box.
7. Click the Apply button.
Now any WiFi device can access the WiFi network of the extender.
Change a Device on the Access List
You can change the name or MAC address of a device on the access list.
To change a WiFi device on the access list:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
Manage the Extender Network and Security Settings
59
N600 WiFi Range Extender
4. Select Advanced > Wireless Settings.
5. Click the Setup Access List button.
6. Select the radio button to the left of the device that you want to change.
7. Click the Edit button.
8. Change the name of the device or the MAC address.
9. Click the Apply button.
The changed settings display in Wireless Card Access List.
Manage the Extender Network and Security Settings
60
N600 WiFi Range Extender
Remove a Device from the Access List
If you no longer want to grant a device access to the WiFi network of the extender, you can
remove the device from the access list.
To remove a WiFi device from the access list:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
4. Select Advanced > Wireless Settings.
5. Click the Setup Access List button.
6. Select the radio button to the left of the device that you want to remove.
7. Click the Delete button.
The device is removed from the Wireless Card Access List.
Manage the Extender Network and Security Settings
61
N600 WiFi Range Extender
Set the Operating Mode to FastLane Technology
The normal operating mode of the extender (also referred to as Internet Surfing mode) is to
allow devices on both 2.4 and 5 GHz bands to connect at the same time. This mode extends
both WiFi bands at the same time, but reduces the WiFi performance.
FastLane Technology offers maximum WiFi performance. It provides high-speed WiFi with a
dedicated band connecting the extender and the WiFi device, and a second band connecting
the extender and the WiFi router. FastLane Technology is ideal for HD gaming and HD video
streaming.
Note: If all your devices and your WiFi router support only the 2.4 GHz
band, or all your devices and your WiFi router support only the 5 GHz
band, do not enable FastLane Technology.
When you enable FastLane Technology, you have two options:
•Use the 2.4 GHz band to connect the extender to the WiFi devices and use the 5 GHz
band to connect the extender to the WiFi router. Use this mode if your WiFi router
supports the 5 GHz band but the devices that you want to use for gaming and streaming
support the 2.4 GHz band.
•Use the 5 GHz band to connect the extender to the WiFi devices and use the 2.4 GHz
band to connect the extender to the WiFi router. Use this mode if the devices that you
want to use for gaming and streaming support the 5 GHz band but your WiFi router
supports the 2.4 GHz band.
To enable FastLane Technology:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
Manage the Extender Network and Security Settings
62
N600 WiFi Range Extender
4. Select Advanced > Operating Mode.
5. By default, the Internet Surfing radio button is selected.
6. Select the FastLane Technology radio button.
7. Select the FastLane Technology option that you want to enable by selecting one of the
following radio buttons:
•Device-to-extender in 5GHz only and extender-to-router in 2.4GHz only.
Your WiFi devices must support the 5 GHz band.
•Device-to-extender in 2.4GHz only and extender-to-router in 5GHz only (Router
must support 5GHz band).
Your WiFi router must support the 5 GHz band. This option is enabled by default.
8. Click Apply.
Your settings are saved.
9. If you are disconnected, reconnect your WiFi device to the extender’s network with its new
settings.
For example, if you were connected to the extender’s network in the 2.4 GHz band, you
now might have to connect in the 5 GHz band, or the other way around.
Manage the Extender Network and Security Settings
63
N600 WiFi Range Extender
Run Smart Setup Again After Initial Setup
There might be situations in which you want to run NETGEAR genie Smart Setup again after
the initial setup.
To run Smart Setup again:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
4. Select Smart Setup.
Smart Setup searches for existing WiFi networks automatically and displays the networks
in the 2.4 GHz band.
5. Select a 2.4 GHz WiFi network to extend, and click the Continue button.
6. Enter the security settings for the existing 2.4 GHz network:
•If the network uses WPA-PSK, WPA2-PSK, or a combination of these options, do the
following:
a. In the Password (network key) field, type the network passphrase (also called
a password or network key).
b. Click the Continue button.
Manage the Extender Network and Security Settings
64
N600 WiFi Range Extender
•If the network uses WEP, do the following:
a. From the Encryption Strength menu, select the encryption strength (64 bit or
128 bit).
b. Specify the active key by selecting the Key 1, Key 2, Key 3, or Key 4 radio
button (only one key can be the active key) and type the value for the key.
For 64-bit WEP, type 10 hexadecimal digits (any combination of 0–9, A–F). For
128-bit WEP, type 26 hexadecimal digits. The key values are not case-sensitive.
c. Click the Continue button.
If Smart Setup detects any networks in the 5 GHz band, it displays them.
7. Select a 5 GHz WiFi network to extend, and click the Continue button.
Note: If your router does not support the 5 GHz band (not all routers do) or
you want to set up the 5 GHz extender network later, click the Skip
button, and go to Step 9 on page 65.
8. Enter the security settings for the existing 5 GHz network:
•If the network uses WPA-PSK, WPA2-PSK, or a combination of these options, do the
following:
a. In the Password (network key) field, type the network passphrase (also called
a password or network key).
b. Click the Continue button.
•If the network uses WEP, do the following:
a. From the Encryption Strength menu, select the encryption strength (64 bit or
128 bit).
b. Specify the active key by selecting the Key 1, Key 2, Key 3, or Key 4 radio
button (only one key can be the active key) and type the value for the key.
For 64-bit WEP, type 10 hexadecimal digits (any combination of 0–9, A–F). For
128-bit WEP, type 26 hexadecimal digits. The key values are not case-sensitive.
c. Click the Continue button.
Manage the Extender Network and Security Settings
65
N600 WiFi Range Extender
Smart Setup displays the network names and adds _2GEXT to the end of the 2.4 GHz
network name and _5GEXT to the end of the 5 GHz network name.
9. Use the default extension names, or, in the Name (2.4GHz SSID) field, and, if you have set
up a 5 GHz network, in the Name (5GHz SSID) field, enter new network names for your
extender WiFi networks, and click the Continue button.
Note: If you do not want to use the same security modes for your extender
networks as you use for your existing networks, clear the check box
before you click the Continue button. You then can configure the
security settings for the extender networks. However, you can also
change the security settings later.
The extender applies the settings.
10. Wait a couple of minutes while the extender creates the WiFi networks.
When the extender is ready, Smart Setup summarizes the extender networks.
11. Use a WiFi network manager on the computer or mobile device to connect to the extender’s
newly created 2.4 GHz or 5 GHz WiFi network.
Manage the Extender Network and Security Settings
66
N600 WiFi Range Extender
Note: Unless you entered a new network name in Step 9, the extender
changes its default NETGEAR_EXT network name to the name of the
WiFi network to which you connected the extender and adds _2GEXT
to the end of the 2.4 GHz network name and _5GEXT to the end of the
5 GHz network name.
Note: If your computer or mobile device cannot join the new WiFi network of
the extender, see Improve the Connection Between the Extender and
the WiFi Router on page 83.
12. Select the My wireless devices are connected to the Extender network check box, and
click the Continue button.
Smart Setup describes the color of the Link Rate LED on the front of the extender.
Because you placed the extender close the WiFi router, the Link Rate LED is green.
13. Click the Finish button.
A pop-up screen displays.
14. To bookmark the URL of the extender, click the OK button.
A NETGEAR website displays. You are now online.
Connect Ethernet-Enabled Devices
You can use the extender to connect as many as four Ethernet-enabled devices, such as
smart TVs, game consoles, and Blu-ray players, to the WiFi network.
After you have set up the extender, plug the Ethernet cable from a device that you want to
connect directly into one of the extender’s Ethernet LAN ports.
By default, the Ethernet ports connect to the 2.4 GHz WiFi band. For information about how
to change the connection to the 5 GHz WiFi band, see Manage the Extender WiFi Settings on
page 43.
Extender
WiFi router
Blue-ray player
TV
Gaming console
Manage the Extender Network and Security Settings
67
N600 WiFi Range Extender
Figure 6. Connecting devices to the LAN ports on the rear panel
Maintain and Monitor the Extender
69
N600 WiFi Range Extender
Back Up and Manage the Extender Configuration
When the extender works correctly after initial setup, NETGEAR recommends that you back
up the extender configuration settings. After you have backed up the settings, if you have
changed the extender configuration settings but are not content with the new settings, you can
restore the extender configuration to the backed-up settings.
Back Up the Configuration Settings
You can back up the configuration file of the extender.
To back up the extender configuration settings:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
4. Select extender Maintenance > Backup Settings.
5. Click the Backup button.
Your browser extracts the configuration file from the extender. By default, the name of the
backup file is NETGEAR_WN2500RPv2.cfg.
6. If you do not have your browser set up to save downloaded files automatically, locate where
you want to save the file.
Maintain and Monitor the Extender
70
N600 WiFi Range Extender
Restore the Configuration Settings
You can restore the configuration file of the extender to a previously saved configuration file.
To restore the extender configuration settings:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
4. Select extender Maintenance > Backup Settings.
5. Click the Browse button.
6. Locate and select the previously saved backup file.
By default, the name of the backup file is NETGEAR_WN2500RPv2.cfg.
CAUTION:
After you click the Restore button, do not try to go online, turn off the
extender, shut down the computer, or do anything else to the extender
until it finishes restarting!
7. Click the Restore button.
A confirmation pop-up screen displays.
8. Confirm your decision.
The extender restarts. This process takes about one minute.
Maintain and Monitor the Extender
71
N600 WiFi Range Extender
Return the Extender to Its Factory Default Settings
Under some circumstances (for example, if you have lost track of the changes that you made
to the extender settings), you might want to erase the configuration and reset it to factory
default settings.
To reset the extender to factory default settings, you can use either the Restore Factory
Settings button on the rear panel or the Erase function. However, if you have lost the
password to access the extender, you must use the Restore Factory Settings button.
For a list of factory default settings, see Factory Default Settings on page 85.
Use the Restore Factory Settings Button
CAUTION:
This process erases any settings that you have configured in the extender.
To reset the extender to factory default settings:
1. Insert a straightened paper clip into the hole of the Restore Factory Settings button
and hold it for about seven seconds.
Restore Factory Settings button
2. Release the button.
The extender resets and restarts. This process takes about one minute.
Maintain and Monitor the Extender
72
N600 WiFi Range Extender
Erase the Extender Configuration Settings
CAUTION:
This process erases any settings that you have configured in the extender.
To erase the extender’s settings:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
4. Select Maintenance > Backup Settings.
CAUTION:
After you click the Erase button, do not try to go online, turn off the
extender, shut down the computer, or do anything else to the extender
until it finishes restarting!
5. Click the Erase button.
A confirmation pop-up screen displays.
6. Confirm your decision.
The extender restarts. This process takes about one minute.
Maintain and Monitor the Extender
73
N600 WiFi Range Extender
Update the Firmware
Unless you changed the settings in the Firmware Update screen previously, the extender is
set up to check for new firmware automatically at login.
To check manually for new firmware and, if available, update the firmware:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
4. Select Maintenance > Firmware Update.
5. Click the Check button.
6. If new firmware is available, follow the onscreen prompts to download it onto your computer.
Note: You might need to unzip the firmware file.
7. Click the Browse button.
8. Locate and select the new firmware file.
The firmware file has a .chk extension.
CAUTION:
After you click the Upload button, do not try to go online, turn off the
extender, shut down the computer, or do anything else to the extender
until it finishes restarting!
9. Click the Upload button.
The firmware update starts and the extender restarts. The firmware update process takes
a couple of minutes.
Maintain and Monitor the Extender
74
N600 WiFi Range Extender
View the Status and Traffic Statistics of the Extender
The Status screen displays when you log in to the extender after initial setup. The Status
screen shows the current settings for the extender and provides access to the traffic statistics,
such as the number of packets sent and number of packets received for each port.
To view the status of the extender, to view the traffic statistics, and to change the poll
interval:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
4. Select Maintenance > Status.
Maintain and Monitor the Extender
75
N600 WiFi Range Extender
The following table describes the fields on the Status screen.
Field Description
Hardware Version The hardware version of the extender.
Firmware Version The current firmware version of the extender. If you upgrade the firmware, this field
changes.
GUI Language Version The language version that is set on the extender. If you upgrade the firmware, this
field might change.
Region The region in which you operate the extender.
Note: If you purchased the extender in the United States or Canada, by default,
the region is North America.
Connection Status to Existing Network (2.4GHz)
Name (SSID) The name (SSID) of the WiFi network in the 2.4 GHz band to which the extender is
connected.
Link Rate The combined transmission (Tx) and receive (Rx) link rate in Mbps of the current
WiFi connection in the 2.4 GHz band.
Connection Status Shows whether the extender is connected to the WiFi network in the
2.4 GHz band.
If the extender is disconnected from the WiFi network in the 2.4 GHz band, a
Connect button displays. Click the Connect button connect the extender to the
WiFi network in the 2.4 GHz band.
Note: The extender can be connected simultaneously to a network in the
2.4 GHz band and to a network in the 5 GHz band. If you have a dual band WiFi
router, the router can broadcast the same network name (SSID) simultaneously in
both bands.
Connection Status to Existing Network (5GHz)
Name (SSID) The name (SSID) of the WiFi network in the 5 GHz band to which the extender is
connected.
Link Rate The combined transmission (Tx) and receive (Rx) link rate in Mbps of the current
WiFi connection in the 5 GHz band.
Connection Status Shows whether the extender is connected to the WiFi network in the 5 GHz band.
If the extender is disconnected from the WiFi network in the 5 GHz band, a
Connect button displays. Click the Connect button connect the extender to the
WiFi network in the 5 GHz band.
Note: The extender can be simultaneously connected to a network in the
5 GHz band and to a network in the 2.4 GHz band. If you have a dual band WiFi
router, the router can broadcast the same network name (SSID) simultaneously in
both bands.
Extender IP Info
MAC Address The physical address of the extender.
IP Address The IP address of the extender. The default is 192.168.1.250.
Maintain and Monitor the Extender
76
N600 WiFi Range Extender
DHCP Client Shows whether the DHCP client of the extender is on.
IP Subnet Mask The IP subnet mask that is associated with the IP address of the extender. The
default is 255.255.255.0.
Gateway IP Address The IP address of the WiFi network gateway.
Domain Name Server The IP address of the Domain Name Server (DNS) of the WiFi network.
Extender Wireless Settings (2.4GHz)
Name (SSID) The name (SSID) of the WiFi network of the extender in the 2.4 GHz band.
Channel The active channel of the WiFi network in the 2.4 GHz band.
Wireless mode The wireless mode in the 2.4 GHz band: Up to 54 Mbps, Up to 145 Mbps, or Up to
300 Mbps.
Wireless AP Shows whether the WiFi access point of the extender is on in the 2.4 GHz band.
Broadcast Name Shows whether broadcasting of the network name (SSID) of the extender is on in
the 2.4 GHz band.
Wi-Fi Protected Setup Shows whether Wi-Fi Protected Setup (WPS) is configured for the 2.4 GHz band.
Extender Wireless Settings (5GHz)
Name (SSID) The name (SSID) of the WiFi network of the extender in the 5 GHz band.
Region The location in which the extender is operating in the 5 GHz band.
Wireless mode The wireless mode in the 5 GHz band: Up to 54 Mbps, Up to 145 Mbps, or Up to
300 Mbps.
Wireless AP Shows whether the WiFi access point of the extender is on in the 5 GHz band.
Broadcast Name Shows whether broadcasting of the network name (SSID) of the extender is on in
the 5 GHz band.
Wi-Fi Protected Setup Shows whether Wi-Fi Protected Setup (WPS) is configured for the 5 GHz band.
Field Description
Maintain and Monitor the Extender
77
N600 WiFi Range Extender
5. Click the Show Statistics button.
The following table describes the traffic statistics fields that display for each of the four
LAN ports, for the WLAN1 port in the 2.4 GHz band, and for the WLAN2 port in the 5 GHz
band.
Field Description
Status The link status and speed of the port.
TxPkts The number of packets transmitted on the port since the extender was restarted.
RxPkts The number of packets received on the port since the extender was restarted.
Collisions The number of collisions on the port since the extender was restarted.
Tx B/s The packet transmission rate in bytes per second on the port.
Rx B/s The packet reception rate in bytes per second on the port.
Up T ime The time elapsed since the connection was initiated.
6. To change the poll interval:
a. Click the Stop button.
b. In the Poll Interval field, enter a new value in seconds.
c. Click the Set Interval button.
Maintain and Monitor the Extender
78
N600 WiFi Range Extender
View the Wired and WiFi Network Devices
You can view the active wired and WiFi devices in both the network to which the extender is
connected and the extender network. If you do not recognize a WiFi device, it might be an
intruder.
To display the wired and WiFi devices:
1. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
2. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
3. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
4. Select Maintenance > Attached Devices.
For each wired and WiFi device, the IP address, device name, MAC address, and virtual
MAC address display.
5. (Optional) Click the Refresh button.
The information onscreen is updated.
FAQs and Troubleshooting
80
N600 WiFi Range Extender
FAQs
This section provides answers for difficulties you might experience with the extender.
1. Question. Does the extender work if I connect it to my WiFi router with an Ethernet
cable?
Answer. No, the extender is designed only to connect over WiFi to a WiFi router.
2. Question. What are the default user name and password to log in to the extender?
Answer. If you are online at www.mywifiext.net, you can use the following user name
and password to log in:
•User name. admin
•Password. password
3. Question. When I try to connect to the network, Smart Setup keeps asking me for my
passphrase, and I am sure I’ve entered the correct passphrase. What can I do?
Answer. It is likely that the extender is placed at the borderline of the range that the WiFi
router covers. For more information, see How to Position the Extender on page 12 and
Improve the Connection Between the Extender and the WiFi Router on page 83.
4. Question. I receive an error message on the Review Settings screen on Smart Setup.
What can I do?
Answer. Make sure that your computer or mobile device is connected to the extender by
using the SSID and the passphrase that you have set up and clicking the Refresh button
in your browser. You should be returned to Smart Setup.
5. Question. I connected to NETGEAR_EXT and launched a browser, but why can I not see
Smart Setup?
Answer. First, make sure that your device is set up to use DHCP. Second, make sure that
the Device to Extender Connection LED is green. Finally, relaunch the browser and enter
www.mywifiext.net.
6. Question. I have enabled a WiFi MAC filter (WiFi access control or ACL) on my WiFi router.
What should I do when installing the extender?
Answer. When the WiFi device connects through the extender to your router, the MAC
address of the WiFi device shown on the router is translated to another MAC address. If
your router's MAC filter is enabled, the WiFi device connects to the extender but cannot
get an IP address from the extender and cannot access the Internet. To allow the WiFi
device to receive an IP address from the extender and access the Internet, you must
provide the translated MAC address to the router.
To get the translated MAC address:
a. Disable the MAC filter on your WiFi router.
b. Turn on the extender and connect all of your WiFi devices to the extender.
c. Make sure that the Link Rate LED remains lit.
FAQs and Troubleshooting
81
N600 WiFi Range Extender
d. On your computer, launch an Internet browser such as Mozilla Firefox or Microsoft
Internet Explorer.
e. In the address field of your browser, enter www.mywifiext.net.
You are prompted to enter a user name and password.
f. Type admin for the user name and type your password.
If you have not yet personalized your password, type password for the password.
g. Select Maintenance > Attached Devices.
h. Write down any MAC addresses that begin with 02:0F:B5 and any virtual MAC
addresses.
i. On your WiFi router, add the MAC addresses that begin with 02:0F:B5 and the
virtual MAC addresses to the MAC filter table.
j. Enable the MAC filter on your WiFi router.
7. Question. My router security is WEP, and I entered the wrong security key on the extender.
I cannot access the extender anymore. What can I do?
Answer. The extender cannot detect whether the WEP password is correct. If you
entered the wrong password, your WiFi device cannot get the IP address from the
extender. You must reset the extender to the factory defaults to get the IP address back.
8. Question. Is seamless roaming supported? During a VoIP call, when I move to a different
location, the call is dropped. What should I do?
Answer. No, the extender does not support seamless roaming. You might notice
performance issues if your WiFi device (laptop, smartphone, or tablet) connects to a
different WiFi network. For example, you might connect to the extender WiFi network,
begin a call, and then move to the location of your existing WiFi network. Your WiFi
device automatically connects to the network in your current location, which takes a few
seconds and might cause your call to be dropped. To prevent this situation, decide which
WiFi network you want to use for your VoIP call, and stay within the range of that
network.
You Cannot Connect to the Extender
If you have trouble connecting to the extender, determine what prevents you from
connecting:
•Make sure that you use the correct user name and password to log in:
-User name. admin
-Password. password
•If your browser displays an error page, include http:// in the address field of your browser
by typing http://www.mywifiext.net.
•If you already set up the extender but can no longer connect to it over WiFi, check if the
Link Rate LED is off or red. For more information, see Improve the Connection Between
the Extender and the WiFi Router on page 83.
FAQs and Troubleshooting
82
N600 WiFi Range Extender
•If you cannot get a WiFi connection working, you can use an Ethernet cable to connect
your computer to the extender. For more information, see Access the Extender over
Ethernet and Use Smart Setup on page 22.
You Cannot Join a WiFi Network and Receive an Error
Message
To join a WiFi network, you must know its network name (also called the SSID) so that you
can select it. If the network is secure, you must know the passphrase or key. If the extender
does not connect to the network that you select, the cause might be one of the following:
•You might have typed the network name, passphrase, or key incorrectly. Use Smart
Setup (see Run Smart Setup Again After Initial Setup on page 63) to select a WiFi
network from the list with detected networks, and retype the passphrase or key. The
passphrase or key is case-sensitive. For example, PASSWORD25 is not the same as
Password25 or password25.
•If the extender cannot detect your WiFi network, check to see if your WiFi network is still
up. Make sure that the WiFi router is turned on. If possible, move the extender closer to
the WiFi router . For more information, see Improve the Connection Between the Extender
and the WiFi Router on page 83.
•If the extender Link Rate LED is red, a poor WiFi connection exists between the WiFi
router and the extender. You can establish the best connection with a clear line of sight
between the extender and the WiFi router. Make sure that no physical obstacles exist
between the extender and the WiFi router , and try to move the extender closer to the WiFi
router. For more information, see Improve the Connection Between the Extender and the
WiFi Router on page 83.
If you use Smart Setup, and the extender cannot connect to the WiFi router or cannot get an
IP address from the WiFi router, or the WiFi router is not connected to the Internet, Smart
Setup might display the following message:
You are not able to connect to Internet. Click “Continue” to run through setup or “Exit” to
manually configure the connection.
Either run Smart Setup again, exit Smart Setup and configure the connection manually (see
Connect the Extender to a WiFi Network Without Using Smart Setup on page 33), or try
Smart Setup again later (see Run Smart Setup Again After Initial Setup on page 63).
FAQs and Troubleshooting
83
N600 WiFi Range Extender
Improve the Connection Between the Extender and the
WiFi Router
The extender LEDs can help you tell whether the extender is correctly set up and working as
it should.
To improve the connection between the extender and the WiFi router:
1. Move the extender closer to the WiFi router or to a different spot where it provides a
better line of sight.
You might need to unplug the extender, plug it in again at its new location, and restart it.
Unless the extender is outside the range of your WiFi router, the extender connects
automatically to the WiFi router.
2. As you move the extender, continue to check the Link Rate LED and the Device to Extender
LED on the top panel until you find a location where the Link Rate LED is green or amber,
and the Device to Extender LED is green.
The following tables describe how the LEDs show the quality of the connection.
2.4 GHz LED Status LED Color Performance
Both the Link Rate LED and the Device
to Extender LED are green. and The extender provides the best performance.
The Link Rate LED is amber and the
Device to Extender LED is green. and The extender provides a workable performance.
The Link Rate LED is red. and The extender provides a poor performance.
The Link Rate LED is off. The extender cannot function.
5 GHz LED Status LED Color Performance
Both the Link Rate LED and the Device
to Extender LED are green. and The extender provides the best performance.
The Link Rate LED is amber and the
Device to Extender LED is green. and The extender provides a workable performance.
The Link Rate LED is red. and The extender provides a poor performance.
The Link Rate LED is off. The extender cannot function.
Factory Settings and Technical Specifications
85
N600 WiFi Range Extender
Factory Default Settings
To reset the extender to factory default settings, you can use either the Restore Factory
Settings button on the rear panel or the Erase function. For more information, see Return the
Extender to Its Factory Default Settings on page 71.
The following table shows the factory default settings.
Table 2. Factory default settings
Factory Settings
Smart Setup Enabled
WiFi WiFi communication Enabled
WiFi network name (SSID) NETGEAR_EXT
Security Disabled
Transmission speed Auto1
1. Maximum WiFi signal rate (IEEE Standard 802.11). Actual throughput can vary. Network conditions and environmental factors,
including volume of network traffic, building materials and construction, and network overhead lower actual data throughput rate.
Country/region Varies by region
Operating mode 802.11n, 802.11a, 802.11g, and 802.11b
Data rate in the 2.4 GHz band Up to 145 Mbps
Data rate in the 5 GHz band Up to 300 Mbps
DHCP Client enabled
Factory Settings and Technical Specifications
86
N600 WiFi Range Extender
Technical and Environmental Specifications
The following table shows the technical and environmental specifications.
Table 3. Technical specifications
Technical Specifications
Network protocol and
standards compatibility Data and routing protocols: TCP/IP, DHCP server and client
Power adapter • North America (input): 120V, 60 Hz
• Australia and UK (input): 240V, 50 Hz
• Europe, excluding the UK (input): 230V, 50 Hz
• All regions (output): 12 VDC @ 2.5A
Physical specifications • Dimensions: 177 x 116 x 30 mm (7.0 x 4.6 x 1.2 in)
• Weight: 0.25 kg (0.54 lb)
Environmental • Operating temperature: 32° to 140°F (0° to 40°C)
• Operating humidity: 90% maximum relative humidity, noncondensing
Interface • Local: 10BASE-T, 100BASE-TX, RJ-45
• 802.11n, 802.11a, 802.11g, and 802.11b
Electromagnetic emissions • FCC Part 15 Class B
• VCCI Class B
• EN 55 022 (CISPR 22), Class B C-Tick N10947