Table of Contents
- Contents
- 1. Overview
- 2. Get Started
- 3. Extender Network Settings
- View Connected Devices
- Boost Your Video Streaming with FastLane Technology
- View WiFi Settings
- Change the WiFi Network Name
- Turn Off the SSID Broadcast to Create a Hidden Network
- Disable or Enable the WiFi Radios
- Change the WiFi Speed
- Use WPS to Add a Computer to the Extender’s WiFi Network
- Deny Access to a Computer or WiFi Device
- Set Up an Access Schedule
- Change the Extender’s Device Name
- Set Up the Extender to Use a Static IP Address
- Use the Extender with MAC Filtering or Access Control
- 4. Maintain and Monitor the Extender
- Change the Extender admin User Name and Password
- Turn Password Protection Off and On
- Recover a Forgotten User Name or Password
- Automatically Adjust for Daylight Saving Time
- Manually Set the Extender Clock
- Back Up and Manage the Extender Configuration
- Return the Extender To Its Factory Default Settings
- Update the Extender Firmware
- 5. FAQs and Troubleshooting
- 6. Factory Settings and Technical Specifications
NETGEAR EX6110 User Manual
Displayed below is the user manual for EX6110 by NETGEAR which is a product in the Network Extenders category. This manual has pages.
Related Manuals
AC1200 WiFi Range Extender
User Manual
Model EX6110
September 2017
202-11748-01
350 E. Plumeria Drive
San Jose, CA 95134
USA
Support
Thank you for purchasing this NETGEAR product.
After installing your device, locate the serial number on the label of your product and use it to register your
product at https://my.netgear.com.You must register your product before you can use NETGEAR telephone
support. NETGEAR recommends registering your product through the NETGEAR w ebsite. For product updates
and web support, visit http://support.netgear.com.
Phone (US & Canada only): 1-888-NETGEAR.
Phone (Other Countries): Check the list of phone numbers at
http://support.netgear.com/general/contact/default.aspx.
Trademarks
©NETGEAR, Inc. NETGEAR and the NETGEAR Logo are trademarks of NETGEAR, Inc. Any non-NETGEAR
trademarks are used for reference purposes only.
Compliance
For regulatory compliance information, visit http://www.netgear.com/about/regulatory. See the regulatory
compliance document before connecting the power supply.
2
AC1200 WiFi Range Extender
Contents
Chapter 1 Overview
Meet Your Extender................................................................................................6
LEDs.................................................................................................................6
Buttons..............................................................................................................7
When to Use Your Extender...................................................................................7
How the Extender Works.......................................................................................7
Chapter 2 Get Started
Install the WiFi Extender......................................................................................10
Place the Extender and Apply Power..............................................................10
Connect to an Existing WiFi Network..............................................................10
Connect with WPS......................................................................................10
Connect with the NETGEAR Installation Assistant.....................................11
Find the Best Location....................................................................................13
Log In to the Extender After Installation...............................................................13
Run Smar t Setup Installation...............................................................................13
Chapter 3 Extender Network Settings
View Connected Devices.....................................................................................16
Boost Your Video Streaming with FastLane Technology......................................16
View WiFi Settings...............................................................................................17
Change the WiFi Network Name..........................................................................18
Tur n Off the SSID Broadcast to Create a Hidden Network..................................18
Disable or Enable the WiFi Radios.......................................................................19
Change the WiFi Speed.......................................................................................20
Use WPS to Add a Computer to the Extender’s WiFi Network............................20
Use WPS with the Push Button Method..........................................................21
Use WPS with the PIN Method.......................................................................21
Deny Access to a Computer or WiFi Device........................................................22
Set Up an Access Schedule................................................................................23
Change the Extender’s Device Name..................................................................24
Set Up the Extender to Use a Static IP Address..................................................25
Use the Extender with MAC Filtering or Access Control......................................25
Chapter 4 Maintain and Monitor the Extender
Change the Extender admin User Name and Password......................................28
Turn Password Protection Off and On..................................................................28
Recover a Forgotten User Name or Password.....................................................29
Automatically Adjust for Daylight Saving Time.....................................................30
Manually Set the Extender Clock.........................................................................30
Back Up and Manage the Extender Configuration...............................................31
Back Up the Configuration Settings................................................................31
3
Restore the Configuration Settings.................................................................32
Retur n the Extender To Its Factor y Default Settings............................................33
Use the Reset Button......................................................................................33
Log In and Reset the Extender to Factor y Settings.........................................33
Update the Extender Fir mware............................................................................34
Check for New Firmware and Update the Router............................................34
Manually Upload Firmware to the Extender....................................................35
Chapter 5 FAQs and Troubleshooting
FAQs....................................................................................................................38
Cannot Connect to the Extender..........................................................................38
Cannot Join a WiFi Network and Receive an Error Message..............................38
Cannot Access mywifiext.net...............................................................................39
Find Extender's IP Address..................................................................................40
Chapter 6 Factory Settings and Technical Specifications
Factor y Default Settings.......................................................................................42
Technical and Environmental Specifications........................................................42
4
AC1200 WiFi Range Extender
1
Overview
The WiFi Range Extender boosts your existing network range and speed, delivering dual-band WiFi.
This chapter covers the following topics:
•Meet Your Extender
•When to Use Your Extender
•How the Extender Works
For more information about the topics covered in this manual, visit the support website at
support.netgear.com.
Note
5
Meet Your Extender
Before you install your extender, familiarize yourself with its LEDs and buttons.
LEDs
The following table describes the LEDs.
Table 1. LED descriptions
DescriptionLED
•Solid green.The extender is powered on.
•Solid amber.The extender is booting.
•Off.The extender is powered off.
Power
This LED indicates the network connection between the extender and the router
or access point.
•Solid green. Best connection.
•Solid amber. Good connection.
•Solid red. Poor connection.
•Off. No connection.
Router
Overview
6
AC1200 WiFi Range Extender
Table 1. LED descriptions (Continued)
DescriptionLED
This LED indicates the network connection between the e xtender and a computer
or mobile device.
•Solid green. Best connection.
•Solid amber. Good connection.
•Solid red. Poor connection.
•Off. No connection.
Device
•Solid green.WiFi security is enabled (WPA or WPA2).
•Blinking green. A WPS connection is being established.
•Off.WiFi security is not enabled.
WPS
Buttons
The side panel contains the following buttons:
•Reset button. Pressing the Reset button for about five seconds resets the extender.
•WPS button. Pressing the WPS button let's the e xtender connect to y our existing WiFi network through
WPS.You can also connect WPS-enabled devices to the extender using the WPS button.
•Power button. Pressing the Power button turn the extender on or off.
When to Use Your Extender
NETGEAR recommends that you connect through the extender network only when the WiFi device is in a
“dead zone” where connection from the existing network is poor or nonexistent. Data traffic routed through
the extender is inherently slower than traffic routed directly from the network.
How the Extender Works
The extender works like a bridge between a WiFi router (or a WiFi access point) and a WiFi device outside
the range of the WiFi router.The extender performs two main jobs:
•The extender connects to a working WiFi network.
When the extender connects over WiFi to an existing network, it functions as a network client, similar
to how a WiFi device connects to a network.
•The extender acts as an access point for WiFi devices.
The e xtender broadcasts its own WiFi network that WiFi devices can join. In its role as an access point,
the extender performs tasks that WiFi routers do, such as broadcasting its network name (SSID).
Overview
7
AC1200 WiFi Range Extender
The extender must do each of these jobs so that both ends of the bridge are in place.
Figure 1. Range extender in a home
Overview
8
AC1200 WiFi Range Extender
Install the WiFi Extender
Place the extender, apply power, and connect the extender to your WiFi network.
Place the Extender and Apply Power
To place the extender and apply power:
1. Place your extender in the same room as your WiFi router.
Proximity to the WiFi router is required only during the initial setup process.
2. Plug the extender into an electrical outlet.
3. Wait for the Power LED to light amber and then turn green.
If the Power LED does not light, press the Power On/Off button on the side of the extender.
Connect to an Existing WiFi Network
To extend the range of your WiFi network, you must connect the extender to your existing WiFi network.
You can do this in one of two ways:
•Connect with WPS. For more information, see Connect with WPS on page 10.
•Connect with web bro wser setup. For more inf ormation, see Connect with the NETGEAR Installation
Assistant on page 11.
Connect with WPS
Wi-Fi Protected Setup (WPS) lets you join a secure WiFi network without typing the network name and
pass word. For help with the WPS button on your WPS-enab led de vice, chec k the instructions or online help
that came with that device. Some older equipment cannot use WPS.
WPS does not support WEP network security or a hidden SSID network. If your
e xisting WiFi network uses WEP security or its SSID is hidden, follo w the instructions
in Connect with the NETGEAR Installation Assistant on page 11.
Note
To use WPS to connect the extender to your WiFi router:
1. Press the WPS button on the extender.
The WPS LED blinks.
2. Within two minutes, press the WPS button on your router or access point.
When the extender connects to your existing WiFi network, the WPS LED on the extender lights solid
green and the Router LED lights.
If the Router Link LED does not light, try again. If it still does not light, see Connect with the NETGEAR
Installation Assistant on page 11.
3. If your WiFi router supports the 5 GHz band, repeat Steps 1 and 2 to connect the extender to the 5 GHz
band.
Get Started
10
AC1200 WiFi Range Extender
4. Unplug the extender and move it to a new location that is about halfway between your router and the
area with a poor router WiFi signal.
The location that you choose must be within the range of your existing WiFi router network.
5. Use the Router LED to help you choose a spot where the extender-to-router connection is optimal.
6. If the Router LED doesn’t light amber or green, plug the extender into an outlet closer to the router and
try again.
Keep moving the extender to outlets closer to the router until the Router LED lights amber or green.
7. On your computer or mobile device, find and connect to a new extender WiFi network.
The extender creates two new extender WiFi networks.The extender’s new WiFi network names are
based on your existing WiFi network name, with _2GEXT and _5GEXT at the end of the name.
For example:
•Existing WiFi network name. MyNetworkName
•New extender WiFi network names. MyNetworkName_2GEXT and MyNetworkName_5GEXT
Use the same WiFi password that you use for your WiFi router.
8. Test the new extender WiFi range by moving your computer or mobile device to the area with a poor
router WiFi signal:
a. Leave your computer or mobile device in the area with a poor router WiFi signal and return to the
extender.
b. Check the Device LED on the extender:
•If the Device LED is solid green or amber, your new extender WiFi network reaches the area
with a poor router WiFi signal and your network setup is complete.
•If the Device LED is red, your new extender WiFi network does not reach the area with a poor
router WiFi signal.
You must move your computer or mobile device closer to the extender until the Device LED
turns solid green or amber.
Connect with the NETGEAR Installation Assistant
You can use the NETGEAR installation assistant to connect your extender to your existing WiFi router
network.To use the NETGEAR installation assistant, you must launch a web browser on your computer or
mobile device.
Get Started
11
AC1200 WiFi Range Extender
To use the NETGEAR installation assistant to connect the extender to your WiFi router:
1. On a computer or mobile device, open the WiFi connection manager and find and connect to the extender
network called NETGEAR_EXT.
When you are connected to the extender, the Device LED lights.
2. Launch web browser.
3. Enter http://www.mywifiext.net.
The NETGEAR installation assistant displays.
4. Follow the prompts to connect your extender to your existing WiFi network.
5. Unplug the e xtender and mov e it to a new location about halfw a y between your router and the area with
a poor WiFi signal.
6. Plug the extender into an electrical outlet and wait for the Power LED to light green.
7. Use the Router LED to help you choose a spot where the extender-to-router connection is optimal.
8. If the Router LED doesn’t light amber or green, plug the extender into an outlet closer to the router and
try again.
Keep moving the extender to outlets closer to the router until the Router LED lights amber or green.
9. Reconnect your computer or mobile device to the new extender WiFi network.
10. Test the new extended WiFi range by moving your computer or mobile device to the area with a poor
router WiFi signal:
a. Leave your computer or mobile device in the area with a poor router WiFi signal and return to the
extender.
b. Check the Device LED on the extender:
•If the Device LED is solid green or amber, your new extender WiFi network reaches the area
with a poor router WiFi signal and your network setup is complete.
•If the Device LED is red, your new extender WiFi network does not reach the area with a poor
router WiFi signal.
You must move your computer or mobile device closer to the extender until the Device LED
turns solid green or amber.
11. Plug the extender into an electrical outlet and wait for the Power LED to light green.
Get Started
12
AC1200 WiFi Range Extender
Find the Best Location
If the WiFi signal is weak, the first time you join the extender network, the Router LED or Device LED is
amber or red. If this happens, adjust the position of the extender:
•If the Router LED is amber or red, move the extender closer to the router.
•If the Device LED is amber or red, move the computer or mobile device closer to the extender.
Log In to the Extender After Installation
After installation, you can log in to the extender to view or change the extender’s settings.
To log in to the extender:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
When you are connected to the extender, the Device Link LED lights.
2. Log in to your extender:
•If you did not enable the One WiFi Name feature, enter www.mywifiext.net in the address field of
the browser.
•If you enabled the One WiFi Name feature, enter one of the following URLs:
-Windows-based computer. http://mywifiext
-Mac computers and iOS devices. http://mywifiext. local
-Android devices. http://<extender's IP address> (for example, http://192.168.1.3)
For more information about how to find your extender's IP address, see Find Extender's IP
Address on page 40.
Run Smart Setup Installation
You can use Smart Setup to change the extender settings.This is an easy way to connect the extender to
a different router or to change the extender WiFi network name (SSID) or WiFi password.
To run Smart Setup:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
Get Started
13
AC1200 WiFi Range Extender
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. Click the SMART SETUP button.
5. Follow the prompts.
Get Started
14
AC1200 WiFi Range Extender
3
Extender Network Settings
This chapter covers the following topics:
•View Connected Devices
•Boost Your Video Streaming with FastLane Technology
•View WiFi Settings
•Change the WiFi Network Name
•Turn Off the SSID Broadcast to Create a Hidden Network
•Disable or Enable the WiFi Radios
•Change the WiFi Speed
•Use WPS to Add a Computer to the Extender’s WiFi Network
•Deny Access to a Computer or WiFi Device
•Set Up an Access Schedule
•Change the Extender’s Device Name
•Set Up the Extender to Use a Static IP Address
•Use the Extender with MAC Filtering or Access Control
15
View Connected Devices
You can view a list of devices that are connected to the extender network.
To view connected devices:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Settings > Connected Devices.
The Connected Devices (WPS) page displays.The devices connected to the extender dsipalys on the
page.
Boost Your Video Streaming with FastLane Technology
Get the most out of your HD entertainment with FastLane technology .With F astLane technology, the extender
connects to your router using one band and connects to y our devices using another band. Because a band
is dedicated to each function, performance is enhanced.
If all your devices and your WiFi router support only the 2.4 GHz band, or all your devices and your WiFi
router support only the 5 GHz band, do not enable FastLane Technology.
When you enable FastLane Technology, two options are available:
•Use the 2.4 GHz band to connect the e xtender to the WiFi de vices and use the 5 GHz band to connect
the extender to the WiFi router. Use this mode if your WiFi router supports the 5 GHz band but the
devices that you want to use for gaming and streaming support the 2.4 GHz band.
•Use the 5 GHz band to connect the e xtender to the WiFi de vices and use the 2.4 GHz band to connect
the extender to the WiFi router. Use this mode if the devices that you want to use for gaming and
streaming support the 5 GHz band but your WiFi router supports the 2.4 GHz band.
To activate FastLane mode:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
Extender Network Settings
16
AC1200 WiFi Range Extender
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Do More > FastLane.
The FastLane Technology page displays.
6. Select the FastLane Technology radio button.
The page adjusts and displays two more radio buttons.
7. Select a radio button:
•Router-to-Extender in 2.4 GHz only and Extender-to-Device in 5 GHz only
•Router to Extender in 5 GHz only and Extender-to-Device in 2.4 GHz only
8. Click the SAVE button.
Your changes are saved.
View WiFi Settings
To view the WiFi settings:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
Extender Network Settings
17
AC1200 WiFi Range Extender
The extender menu displays.
5. Select Settings > Wireless.
The WiFi Settings page displays.
Change the WiFi Network Name
To change the WiFi network name:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Settings > Wireless.
The WiFi Settings page displays.
6. In each Network Name (SSID) field, type a network name.
7. Click the SAVE button.
Your settings are saved.
Turn Off the SSID Broadcast to Create a Hidden Network
By def ault, the extender broadcasts its WiFi signal so that its wireless network names (SSIDs) are easy for
you to find and connect to from your computer, tablet, or smartphone.You can turn off the SSID broadcast
to create a hidden WiFi network.To connect to a hidden network you must know its SSID and password
and manually enter them.
To turn off the SSID broadcast to create a hidden network:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
Extender Network Settings
18
AC1200 WiFi Range Extender
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Settings > Wireless.
The WiFi Settings page displays.
6. Clear the Broadcast the Network Name (SSID) check box.
7. Click the SAVE button.
Your settings are saved.
Disable or Enable the WiFi Radios
By def ault, the e xtender’s WiFi r adios broadcast signals in the 2.4 GHz and 5 GHz bands . If you disable the
WiFi radios, then no one can connect with WiFi to the extender.
To enable or disable the WiFi radios:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Settings > Wireless.
The WiFi Settings page displays.
Extender Network Settings
19
AC1200 WiFi Range Extender
6. Select or clear the Enable 2.4 GHz WiFi check box.
7. Select or clear the Enable 5 GHz WiFi check box.
8. Click the SAVE button.
Your settings are saved.
Change the WiFi Speed
The 2.4 GHz network WiFi speed to set to a specific WiFi speed.You can only change the 5 GHz WiFi
speed.
To change the WiFi speed:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Settings > Wireless.
The WiFi Settings page displays.
6. In the 5 GHz network WiFi Speed menu, select a speed.
7. Click the SAVE button.
Your settings are saved.
Use WPS to Add a Computer to the Extender’s WiFi
Network
WPS (WiFi Protected Setup) lets you connect a computer or WiFi device to the extender’s network without
entering the WiFi network passphrase or key. Instead, you use a WPS button or enter a PIN to connect.
If you use the push button method, the WiFi device that you are trying to connect must include a physical
button or a software button. If you use the PIN method, you must know the PIN of the WiFi device that you
are trying to connect.
Extender Network Settings
20
AC1200 WiFi Range Extender
WPS supports WPA and WPA2 WiFi security. If your extender network is open (no WiFi security is set),
connecting with WPS automatically sets WPA + WPA2 WiFi security on the e xtender network and generates
a random passphrase.You can view this passphrase on the WiFi Settings page (for more information, see
View WiFi Settings on page 17).
Use WPS with the Push Button Method
For you to use the push button method to connect a WiFi device to the extender’s WiFi network, the WiFi
device that you are trying to connect must include a physical WPS button or an onscreen WPS button that
you can click.
To use WPS to add a computer or WiFi device to the extender’s WiFi network:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Settings > Do More > Connect Devices (WPS).
The Connected Devices (WPS) page displays.
6. Leave the Push Button (recommended) radio button selected.
7. Click the WIFI PROTECTED SETUP (WPS) button.
For two minutes, the extender attempts to add the computer or WiFi device to its WiFi network.
8. Within two minutes, go to the computer WiFi device and press or click its WPS button.
9. To verify that the WiFi device is connected to the e xtender’ s WiFi network, select Settings > Connected
Devices.
The WiFi device displays onscreen.
Use WPS with the PIN Method
To use the PIN method to connect a WiFi device to the extender’s WiFi network, you must know the PIN of
the WiFi device that you are trying to connect.
Extender Network Settings
21
AC1200 WiFi Range Extender
To add a computer or WiFi device to the extender’s WiFi network:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Settings > Do More > Connect Devices (WPS).
The Connect Devices (WPS) page displays.
6. Select the PIN Number radio button.
The page adjusts.
7. Type the PIN of the WiFi device in the field.
8. Click the NEXT button.
For four minutes, the extender attempts to find the computer or WiFi device.
9. Within four minutes, go to the WiFi device and use its WPS software to join the WiFi network.
10. To verify that the WiFi device is connected to the e xtender’ s WiFi network, select Settings > Connected
Devices.
The WiFi device displays onscreen.
Deny Access to a Computer or WiFi Device
By default, access control is disabled so that it is easy for you to connect to the extender’s WiFi networks.
You can deny network access to specific computers and WiFi de vices based on their MA C addresses. Each
network device is assigned a MAC address, which is a unique 12-character physical address, containing
the hexadecimal characters 0–9, a–f, or A–F only, and separated by colons (for example, 00:09:AB:CD:EF:01).
Typically, the MA C address is on the label of the WiFi device . If y ou cannot access the label, you can displa y
the MAC address using the network configuration utilities of the computer.You might also find the MAC
addresses on the Connected Devices page (see View Connected Devices on page 16).
To use WiFi access control to deny access:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
Extender Network Settings
22
AC1200 WiFi Range Extender
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Settings > Connected Devices.
The Connected Devices (WPS) page displays.
6. In the WiFi Devices section, select the Enable Access Control check box.
The WiFi devices table displays the names and MAC addresses of WiFi devices that are connected to
the extender.
7. Select the Deny check box for the device.
8. Click the SAVE button.
Your settings are saved and that device cannot connect to the extender’s WiFi network.
Set Up an Access Schedule
You can control access to all users during specific periods of the day.You can set up an access schedule
that prevents Internet access through the extender network based on the times that you set.
To set up an access schedule:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
Extender Network Settings
23
AC1200 WiFi Range Extender
5. Select Do More > Access Schedule.
The Access Schedule pahe displays.
6. Select the Access Schedule On radio button.
The page adjusts.
7. In the Days menu and the Time menu, select the day and time when y ou want to disable Internet access.
8. Click the Add Time button to add the time that you specified to the Scheduled Times table.
9. Click the SAVE button.
Your settings are saved.
Change the Extender’s Device Name
The default name is EX3800.
To change the extender’s device name:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Settings > Wireless Settings.
The WiFi Settings page displays.
6. Scroll down and click the IP Address heading.
The page expands.
7. In the Device Name field, type a name.
8. Click the SAVE button.
Your settings are saved.
Extender Network Settings
24
AC1200 WiFi Range Extender
Set Up the Extender to Use a Static IP Address
The extender comes set up to use a dynamic IP address, which is the correct setting for most home networks.
To set up the extender to use a static IP address:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Settings > Wireless Settings.
The WiFi Settings page displays.
6. Scroll down and click the IP Address heading.
The page expands.
By default, the Dynamically get IP Address from Router radio button is selected.
7. Select the Use Static IP Address radio button.
8. Complete the fields to specify the IP network IP addresses.
9. Click the SAVE button.
Your settings are saved.
Use the Extender with MAC Filtering or Access Control
When the WiFi device connects through the e xtender to your router , the MA C address of the wireless de vice
that is shown on the router is tr anslated to another MAC address . If y our router's MA C filter , wireless access
control, or A CL is enabled, the WiFi device connects to the e xtender but cannot get an IP address from the
extender and cannot access the Internet.To allow the wireless device to receive an IP address from the
extender and access the Internet, you must provide the translated MAC address to the router.
Extender Network Settings
25
AC1200 WiFi Range Extender
To add a translated MAC address to your router:
1. Log in to your router and disable the MAC filter, wireless access control, or ACL.
For more information about how to disable your router’s MAC filter, wireless access control, or ACL,
see your router’s documentation.
2. Power on the extender and connect all of your WiFi devices to the extender.
3. Launch a web browser from a computer or mobile device that is connected to your extender network.
4. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
5. Enter your admin email and password and click the LOG IN button.
The Status page displays.
6. If your browser displays the Menu icon , click it.
The extender menu displays.
7. Select Settings > Connected Devices.
The Connected De vices section displays the MA C addresses and virtual MAC addresses f or computers
and WiFi devices that are connected to the extender network.
8. On the router, add the extender’s virtual MAC address and all the virtual MAC addresses connected to
the extender network to your router’s MAC filter table.
9. Enable the router’s MAC filter, wireless access control, or ACL.
Extender Network Settings
26
AC1200 WiFi Range Extender
4
Maintain and Monitor the Extender
This chapter covers the following topics:
•Change the Extender admin User Name and Password
•Turn Password Protection Off and On
•Recover a Forgotten User Name or Password
•Automatically Adjust for Daylight Saving Time
•Manually Set the Extender Clock
•Back Up and Manage the Extender Configuration
•Return the Extender To Its Factory Default Settings
•Update the Extender Firmware
27
Change the Extender admin User Name and Password
You can change the admin user name and password to log in to the extender.
To add an extender user:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Settings > Password.
The Password Settings page displays.
6. To change the admin user name, enter a new email address in the New User Name field.
7. To change the admin password, enter a new password in the New Password field and the Verify
Password field.
8. Select questions and enter the answers.
9. Click the SAVE button.
Your settings are saved.
Turn Password Protection Off and On
NETGEAR recommends that you leave password protection on to help keep your network secure.You can
turn password protection off and on.
To turn password protection off or on:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
Maintain and Monitor the Extender
28
AC1200 WiFi Range Extender
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Settings > Password.
The Password Settings page displays.
6. Select the Password Off or Password On radio button.
7. Click the SAVE button.
Your settings are saved.
Recover a Forgotten User Name or Password
If you changed the password to access the extender and set up password recovery, you can recover your
password if you lose it.
To recover your password to access the extender:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Click the Username & Password Help link.
A page displays requesting the answers to your security questions.
If you forgot the answers to your security questions, restore the extender’s factory settings and set up
your login credentials again. See Return the Extender To Its Factory Default Settings on page 33.
4. Enter the saved answers to your security questions.
5. Click the NEXT button.
Your email and password are displayed.
6. Click the BACK button.
A login page displays.
7. Log in to the extender.
Maintain and Monitor the Extender
29
AC1200 WiFi Range Extender
Automatically Adjust for Daylight Saving Time
To set up the extender to automatically adjust for daylight saving time:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Do More > Access Schedule.
The Access Schedule page displays.
6. Select the Automatically adjust for daylight savings time check box.
7. Click the SAVE button.
Your settings are saved.
Manually Set the Extender Clock
If you turned on the access schedule, you can set the extender clock.The extender clock makes sure that
the that the WiFi access schedules are accurate.
To manually set the extender clock:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
Maintain and Monitor the Extender
30
AC1200 WiFi Range Extender
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Do More > Access Schedule.
The Access Schedule page displays.
6. In the Extender Clock section, select the Manual radio button.
7. To specify the time, complete the fields or click the Sync Cloc k button to synchroniz e the e xtender time
to the time on the computer or mobile device that you are using.
8. Click the SAVE button.
Your settings are saved.
Back Up and Manage the Extender Configuration
When the extender works correctly after initial setup, NETGEAR recommends that you back up the extender
configuration settings. After you ha ve bac k up the settings, if y ou change the extender configur ation settings
but are not content with the new settings, you can restore the extender configuration to the backed-up
settings.
Back Up the Configuration Settings
You can back up the configuration file of the extender.
To back up the extender configuration settings:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Settings > Other.
The Other Settings page displays.
6. Click the BACKUP button.
Your browser extracts the configuration file from the extender.The backup file uses an .cfg extenstion.
Maintain and Monitor the Extender
31
AC1200 WiFi Range Extender
7. If your browser is not set up to save downloaded files automatically, locate where you want to save the
file.
8. Click the OK button.
The extender configuration settings are backed up.
Restore the Configuration Settings
You can restore the configuration file of the extender to a previously saved configuration file.
To restore the extender configuration settings:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Settings > Other.
The Other Settings page displays.
6. Click the BROWSE button.
7. Locate and select the previously saved backup file.
The backup file uses a .cfg extension.
CAUTION:
After you click the RESTORE button, do not try to go online, turn off the
extender, shut down the computer, or do anything else to the extender
until it finishes restarting!
8. Click the RESTORE button.
A confirmation pop-up window opens.
9. Confirm your decision.
The e xtender configuration is restored and the extender restarts.This process takes about one minute .
Maintain and Monitor the Extender
32
AC1200 WiFi Range Extender
Return the Extender To Its Factory Default Settings
Under some circumstances (for example, if you lose track of the changes that you made to the extender
settings), you might want to erase the configuration and reset the extender to factory default settings.
To reset the extender to factory default settings, you can either use the Factory Reset button on the side
panel or log in to the extender and reset it.
Use the Reset Button
CAUTION:
This process erases any settings that you configured in the extender.
To use the Reset button to return the extender to its factory default settings:
1. Insert a straightened paper clip into the hole of the Reset button and hold it for about seven seconds.
2. Release the button.
CAUTION:
Do not try to go online, turn off the extender, shut do wn the computer, or
do anything else to the extender until it finishes restarting!
The extender resets and restarts.This process takes about one minute.
Log In and Reset the Extender to Factory Settings
CAUTION:
This process erases any settings that you configured in the extender.
To log in to the extender and reset the extender's factory settings:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
Maintain and Monitor the Extender
33
AC1200 WiFi Range Extender
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Settings > Other.
The Other Settings page displays/
CAUTION:
After you click the RESET button, do not try to go online, turn off the
extender, shut down the computer, or do anything else to the extender
until it finishes restarting!
6. Click the RESET button.
A confirmation pop-up window opens.
7. Confirm your decision.
The extender returns to its factory settings and restarts.This process takes about one minute.
Update the Extender Firmware
You can log in to the extender and check if new firmware is available, or you can manually load a specific
firmware version to your extender.
Check for New Firmware and Update the Router
Unless you changed the settings in the Firmware Update page previously, the extender is set up to check
for new firmware automatically at login.
To check manually for new firmware and, if available, update the firmware:
1. Launch a web browser from a computer or mobile device that is connected to your extender network.
2. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
3. Enter your admin email and password and click the LOG IN button.
The Status page displays.
Maintain and Monitor the Extender
34
AC1200 WiFi Range Extender
4. If your browser displays the Menu icon , click it.
The extender menu displays.
5. Select Firmware Update.
The Firmware Update page displays.
6. Click the CHECK ONLINE button.
7. If new firmware is available, follow the onscreen prompts to update the firmware.
You might need to unzip the firmware file.The firmware update process takes about
two minutes.
Note
Manually Upload Firmware to the Extender
If you want to upload a specific firmware version, follow these instructions.
To manually upload a firmware file to your extender:
1. Launch a web browser from a computer that is connected to your extender network.
2. Download the firmware f or your e xtender from the NETGEAR Download Center, sav e it to your desktop ,
and unzip the file if needed.
You might need to unzip the firmware file.
3. Log in to your extender:
•If your extender and router use different WiFi network names (SSIDs), enter www.mywifiext.net.
•If your extender and router use the same WiFi network name (SSID), enter http://<extender’s IP
address> (for example, http://192.168.1.3).
F or more information about how to find y our e xtender's IP address, see Find Extender's IP Address
on page 40.
A login page displays.
4. Enter your admin email and password and click the LOG IN button.
The Status page displays.
5. If your browser displays the Menu icon , click it.
The extender menu displays.
6. Select Firmware Update.
The Firmware Update page displays.
7. Click the BROWSE button.
8. Locate and select the new firmware file.
The firmware file name ends with a .chk extension.
Maintain and Monitor the Extender
35
AC1200 WiFi Range Extender
CAUTION:
After you click the UPLOAD button, do not try to go online, turn off the
extender, shut down the computer, or do anything else to the extender
until it finishes restarting!
9. Click the UPLOAD button.
The firmware update starts and the extender restarts.The firmware update process takes about two
minutes.
Maintain and Monitor the Extender
36
AC1200 WiFi Range Extender
FAQs
This section provides answers for difficulties you might experience with the extender.
The web browser setup keeps asking me for my network password (passphrase) or security key,
and I am sure that I entered the correct password.What can I do?
The extender is probably placed at the borderline of the range covered by the router or access point. For
more information about where to place the extender, see Find the Best Location on page 13.
If you are using WEP security, make sure that you are typing the network password in the correct field.
I forgot my admin email address and password.What can I do?
In the login window, click the Username & Password Help link to answer the security questions that you
set up during the initial setup. For more information, see Recover a Forgotten User Name or Password on
page 29.
To restore factory settings:
1. Use a sharp object such as a pen or paper clip to press and hold the Reset button on the extender for
seven seconds until the Power LED lights amber.
2. Release the Reset button and wait for the extender to reboot.
The extender resets and returns to the factory default settings.
Cannot Connect to the Extender
If you cannot connect to the extender, determine what prevents you from connecting:
•If you cannot access www.mywifiext.net, see Cannot Access mywifiext.net on page 39 for more
information.
•If you forgot your user name or password, click the Username & Password Help link. For more
information, see FAQs on page 38.
•If your browser displays an error page, include http:// in the address field of your browser by typing
http://www.mywifiext.net.
•If you already set up the extender but can no longer connect to it over WiFi, check to see if the Device
LED is off or red.
Cannot Join a WiFi Network and Receive an Error Message
To join a WiFi network, you must know its network name (also called the SSID) so that you can select it. If
the network is secure, you must know the passphrase or k ey. If the extender does not connect to the network
that you select, the cause might be one of the following:
•It is possible that you typed the network name, passphrase, or key incorrectly. Use Smart Setup (see
Run Smart Setup Installation on page 13) to select a WiFi network and retype the passphrase or key.
FAQs and Troubleshooting
38
AC1200 WiFi Range Extender
The passphrase or k ey is case-sensitive . F or example, PASSWORD25 is not the same as Pass word25
or password25.
•If the e xtender cannot detect y our WiFi netw ork, check to see if y our WiFi network is still working. Mak e
sure that the WiFi router is turned on. If possible, move the extender closer to the WiFi router.
•If the extender Device Link LED is red, the WiFi connection between the WiFi router and the extender
is poor.You can establish the best connection with a clear line of sight between the extender and the
WiFi router. Make sure that no physical obstacles exist between the extender and the WiFi router, and
try to move the extender closer to the WiFi router.
If you use Smart Setup, and the extender does not connect to the WiFi router, does not connect to the
Internet, or cannot get an IP address from the WiFi router, Smart Setup displays a message to notify you
that the extender is not configured.
To run Smart Setup again, click the YES button.To manually configure the extender, click the NO,
CONFIGURE MANUALLY button.
Cannot Access mywifiext.net
When you try to access www.mywifiext.net to set up your extender, you might receive an error message
that says you are not connected to the extender's WiFi network.This website is not a regular Internet website.
It is a local web address used to log in to the extender web interface and view the extender's settings.
Your computer or mobile de vice must be connected to y our extender network to access www.mywifiext.net.
Try these troubleshooting tips to connect to www.mywifiext.net:
•If you're trying to access www.mywifiext.net for the first time to set up your extender, see Connect with
the NETGEAR Installation Assistant on page 11 and follow the instructions.
•After you connect y our computer or mobile device to the e xtender network, make sure that the extender's
Device LED is solid green or amber.
If the Device LED is not lit, open your computer's or mobile device's WiFi connection manager and mak e
sure that your device is still connected to the extender network.
•Launch a web browser and enter the extender's default IP address, which is 192.168.1.250.
If this IP address does not work, your e xtender's IP address might ha v e changed.You can log in to your
router to view your extender's IP address. For more information, see Find Extender's IP Address on
page 40.
•If your e xtender and router use the same WiFi network name (SSID), enter http://<extender’s IP address>
(for example, http://192.168.1.3).
F or more information about how to find your extender's IP address, see Find Extender's IP Address on
page 40.
•Clear your web browser's cache and browsing history and try again.
For more information, see the help content for your web browser.
•Try using another web browser.
•Assign a static IP address to your computer.
Before you change any network settings, note your current Default gateway (Windows) or Router
(Mac) address. Use the IP address 192.168.1.249 and the subnet mask 255.255.255.0.
For more information, see your computer's documentation.
FAQs and Troubleshooting
39
AC1200 WiFi Range Extender
Find Extender's IP Address
If your e xtender and router use the same WiFi netw ork name (SSID) and you want to log in to y our e xtender
using an Android device, you must use the extender's IP address.
You can log in to your router to find your extender's IP address. If you own a NETGEAR router, use the
f ollowing example to find the e xtender's IP address. If you do not o wn a NETGEAR router, see your router's
documentation.
The following instructions might not apply to your NETGEAR router. For more
information, see your NETGEAR router's user manual.
Note
To log in to your extender and find your extender's IP address:
1. Launch a web browser from a computer or mobile device that is connected to the router network.
2. Enter http://www.routerlogin.net.
A login window opens.
3. Enter the router admin user name and password.
The user name is admin.The password is the one that you specified the first time that you logged in.
The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Attached Devices.
A list of devices connected to your router displays.
5. Find your extender in the list and note your extender’s IP address.
FAQs and Troubleshooting
40
AC1200 WiFi Range Extender
Factory Default Settings
To reset the extender to f actory default settings , y ou can use the Reset b utton on the side panel or you can
log in and click the onscreen RESET button. For more information, see Return the Extender To Its Factory
Default Settings on page 33.
The following table shows the factory default settings.
Table 2. Factory default settings
Default SettingsFeature
EnabledSmart Setup
EnabledWiFi communication
NETGEAR_EXTWiFi network name (SSID)
DisabledSecurity
Auto1
Transmission speed
Varies by regionCountry/region
802.11a/b/g/n/acOperating mode
54/145/300/433/867 MbpsData rate in the 2.4 GHz band
54/145/300/433 MbpsData rate in the 5 GHz band
Client enabledDHCP
1Maximum WiFi signal rate (IEEE Standard 802.11). Actual throughput can vary. Network conditions and environmental
factors, including volume of network traffic, building materials and construction, and network overhead lower actual data
throughput rate.
Technical and Environmental Specifications
The following table shows the technical and environmental specifications.
Table 3.Technical specifications
Technical Specifications
Data and routing protocols:TCP/IP, DHCP server and client, DNS relay,Network protocol and
standards compatibility
•Dimensions: 72.5 x 72.5 x 64.8 mm (2.85 x 2.85 x 2.55 in.)
•Weight: 152 g (0.34 lb)
Physical specifications
Factory Settings and Technical Specifications
42
AC1200 WiFi Range Extender
Table 3.Technical specifications (Continued)
Technical Specifications
•Operating temperature: 32° to 140°F (0° to 40°C)
•Operating humidity: 90% maximum relative humidity, noncondensing
Environmental
802.11ac, 802.11a, 802.11g, 802.11bInterface
Factory Settings and Technical Specifications
43
AC1200 WiFi Range Extender