8-Port or 16-Port Gigabit Smart Managed Pro Switch with PoE+ and 2 SFP Ports
Contents
1 Get Started
2 Configure System Information
3 Configure Switching
4 Configure Routing
5 Configure Quality of Service
6 Manage Device Security
7 Monitor the Switch and the Traffic
8 Maintain or Troubleshoot the Switch
A Configuration Examples
B Specifications and Default Settings

NETGEAR GS510TPP User Manual

Displayed below is the user manual for GS510TPP by NETGEAR which is a product in the Network Switches category. This manual has pages.

Related Manuals

NETGEAR GS510TPP Manual

NETGEAR NETGEAR Manual

NETGEAR AGM731F Manual

NETGEAR ProSafe GS724TR Manual

NETGEAR GS608-300PES Manual

NETGEAR N600 Manual

NETGEAR GSM7248 Manual

NETGEAR, Inc.

350 East Plumeria Drive

San Jose, CA 95134, USA

August 2019

202-11733-03

User Manual

8-Port or 16-Port Gigabit

Smart Managed Pro Switch

with PoE+ and 2 SFP Ports

Models

GS418TPP

GS510TLP

GS510TPP

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

User Manual2

Support

Thank you for purchasing this NETGEAR product. You can visit https://www.netgear.com/support/ to register your

product, get help, access the latest downloads and user manuals, and join our community. We recommend that you

use only official NETGEAR support resources

Compliance and Conformity

For regulatory compliance information including the EU Declaration of Conformity, visit

https://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

Do not use this device outdoors. If you connect cables or devices that are outdoors to this device, see

http://kb.netgear.com/000057103 for safety and warranty information.

Trademarks

trademarks are used for reference purposes only.

Revision History

Publication

Part Number Publish Date Comments

202-11733-03 August 2019

202-11733-02 June 2018 We updated Configure the VLAN Settings.

202-11733-01 April 2017 First publication.

• We added Available publications.

• We entirely revised the information in Chapter 1, Get Started and added the

following new sections:

Use the NETGEAR Switch Discovery Tool to access the switch

Use the NETGEAR Insight app to discover and register the switch

Change the language of the local browser interface

• We entirely revised Control access with profiles and rules.

• We made changes to Configure access control lists.

• We added Hardware technical specifications.

• We changed web-based management interface, web browser–based

management interface, web interface, switch management interface, device

management interface, and management interface to local browser interface.

• We removed information about the resource CD.

• We made multiple minor additions and changes to the content.

• We made improvements to the organization of the manual.

• We updated the manual to the latest NETGEAR format.

Contents

Chapter 1 Get Started

Available publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Switch management and discovery overview. . . . . . . . . . . . . . . . . . . . . . . .13

Change the default IP address of the switch . . . . . . . . . . . . . . . . . . . . . . . . . 13

Discover or change the switch IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Discover a switch in a network with a DHCP server. . . . . . . . . . . . . . . . .14

Discover a switch in a network without a DHCP server. . . . . . . . . . . . . .15

Use the NETGEAR Switch Discovery Tool to access the switch . . . . . . .17

Use the NETGEAR Insight app to discover and register the switch . . .18

Configure a static IP address from a directly connected computer . . .19

About the user interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Requirements for the local browser interface. . . . . . . . . . . . . . . . . . . . . .20

Supported web browsers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Access the local browser interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Navigation tabs, configuration menus, and page menu. . . . . . . . . . . . .22

Configuration and status options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Buttons in the local browser interface . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

User-defined fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Change the language of the local browser interface . . . . . . . . . . . . . . . . . . 24

Use the Device View of the local browser interface . . . . . . . . . . . . . . . . . . . 25

Power LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Fan LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Interface naming conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Configure interface settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Context–sensitive help and access to the support website . . . . . . . . . . . . . 31

Access the user manual online . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Chapter 2 Configure System Information

View or define system information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

View the temperature sensor information. . . . . . . . . . . . . . . . . . . . . . . . .36

View the fan status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

View the status of the power supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

View the software versions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

View the system CPU status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Configure the CPU thresholds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

View the USB device information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Configure the IP network settings for management access . . . . . . . . . . . . 44

Configure the IPv4 network and VLAN settings for the

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

User Manual4

local browser interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Configure the IPv6 network settings for the local browser interface . .46

View the IPv6 network neighbor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Configure the time settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Configure the time setting manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Configure the time settings with SNTP . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Configure the global SNTP settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

View the SNTP global status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Configure an SNTP server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Configure daylight saving time settings . . . . . . . . . . . . . . . . . . . . . . . . . .60

View the daylight saving time status . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

Configure denial of service settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Configure Auto-DoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Configure denial of service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Configure the DNS settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Configure the global DNS settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

Configure and view host name-to-IP address information. . . . . . . . . . .69

Configure green Ethernet settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Enable the green Ethernet settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

Configure green Ethernet interface settings. . . . . . . . . . . . . . . . . . . . . . .72

Configure green Ethernet local and remote devices . . . . . . . . . . . . . . .73

View green Ethernet remote device details . . . . . . . . . . . . . . . . . . . . . . .76

View the green Ethernet statistics summary . . . . . . . . . . . . . . . . . . . . . . .77

Configure the green Ethernet EEE LPI history . . . . . . . . . . . . . . . . . . . . .79

Use the Device View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Configure Power over Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Configure the global PoE settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Configure the PoE port settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

Configure SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Configure the SNMPv1 or SNMPv2 community . . . . . . . . . . . . . . . . . . . .85

Configure SNMPv1 and SNMPv2 trap settings. . . . . . . . . . . . . . . . . . . . .88

Configure SNMPv1 and SNMPv2 trap flags . . . . . . . . . . . . . . . . . . . . . . .90

View the supported MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Configure SNMPv3 users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92

Configure LLDP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Configure the LLDP global settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93

Configure the LLDP port settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95

View the LLDP-MED network policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

Configure the LLDP-MED port settings . . . . . . . . . . . . . . . . . . . . . . . . . . .97

View the local LLDP information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98

View the LLDP-MED neighbor device information . . . . . . . . . . . . . . . 101

Configure a DHCP L2 relay, DHCP

snooping, and dynamic ARP inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . .104

Configure a DHCP L2 relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Configure DHCP snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Manage dynamic ARP Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

Set up PoE timer schedules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123

Create a PoE timer schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

User Manual5

Specify the settings for an absolute PoE Timer schedule . . . . . . . . . . 124

Specify the settings for a recurring PoE timer schedule . . . . . . . . . . . 125

Change the settings for a recurring PoE timer schedule entry . . . . . 127

Delete a PoE timer schedule entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

Delete a PoE timer schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

Chapter 3 Configure Switching

Configure the port settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

Configure link aggregation groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134

Configure the LAG settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

Configure LAG membership . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

Set the LACP system priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

Set the LACP port priority settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138

Configure VLANs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139

Configure the VLAN Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

Configure VLAN membership . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

View the VLAN status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

Configure the port PVID settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

Configure a MAC-based VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

Configure protocol-based VLAN groups. . . . . . . . . . . . . . . . . . . . . . . . 149

Configure protocol-based VLAN group membership. . . . . . . . . . . . . 151

Configure a voice VLAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152

Configure GARP switch settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153

Configure GARP ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154

Configure Auto-VoIP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156

Configure Auto-VoIP protocol-based settings . . . . . . . . . . . . . . . . . . . 156

Configure the Auto-VoIP OUI-based properties. . . . . . . . . . . . . . . . . . 158

Configure the OUI-based port settings . . . . . . . . . . . . . . . . . . . . . . . . . 159

Manage the OUI table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160

Display the Auto-VoIP status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162

Configure Spanning Tree Protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163

Configure the STP settings and view the STP status . . . . . . . . . . . . . . 164

Configure the CST settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166

Configure the CST port settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167

View the CST port status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170

View Rapid STP Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171

Manage the MST settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172

Configure and view the port settings for an MST instance . . . . . . . . . 175

View the STP statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177

Configure multicast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178

View, search, or clear the MFDB table . . . . . . . . . . . . . . . . . . . . . . . . . . 179

View the MFDB statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180

Configure the auto-video multicast settings . . . . . . . . . . . . . . . . . . . . . 181

Manage IGMP snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182

Configure IGMP snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182

Configure IGMP snooping for interfaces. . . . . . . . . . . . . . . . . . . . . . . . 184

View, search, or clear the IGMP snooping table. . . . . . . . . . . . . . . . . . 185

Configure IGMP snooping for VLANs . . . . . . . . . . . . . . . . . . . . . . . . . . 186

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

User Manual6

Modify IGMP snooping settings for a VLAN . . . . . . . . . . . . . . . . . . . . . 188

Disable IGMP snooping on a VLAN and remove it from the table . . 188

Configure one or more IGMP multicast router interfaces. . . . . . . . . . 189

Configure an IGMP multicast router VLAN . . . . . . . . . . . . . . . . . . . . . . 190

IGMP snooping querier overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191

Configure an IGMP snooping querier . . . . . . . . . . . . . . . . . . . . . . . . . . 191

Configure an IGMP snooping querier for a VLAN . . . . . . . . . . . . . . . . 192

Display the status of the IGMP snooping querier for VLANs . . . . . . . 193

Manage MLD snooping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .195

Enable MLD snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195

Configure MLD snooping for interfaces . . . . . . . . . . . . . . . . . . . . . . . . 196

Configure the MLD VLAN settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198

Modify the MLD snooping settings for a VLAN . . . . . . . . . . . . . . . . . . 199

Remove MLD snooping from a VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . 200

Configure one or more MLD multicast router interfaces . . . . . . . . . . 200

Configure an MLD multicast router VLAN . . . . . . . . . . . . . . . . . . . . . . . 201

Configure an MLD snooping querier . . . . . . . . . . . . . . . . . . . . . . . . . . . 202

Configure the MLD snooping querier VLAN settings . . . . . . . . . . . . . 203

Configure multicast VLAN registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . .205

Configure the global MVR settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205

Configure an MVR group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207

Configure MVR group membership. . . . . . . . . . . . . . . . . . . . . . . . . . . . 208

Configure the MVR interface settings . . . . . . . . . . . . . . . . . . . . . . . . . . 208

View the MVR statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210

View, search, and manage the MAC address table. . . . . . . . . . . . . . . . . . .211

View, search, or clear the MAC address table . . . . . . . . . . . . . . . . . . . 211

Set the dynamic address aging interval. . . . . . . . . . . . . . . . . . . . . . . . . 213

Add a static MAC address to the MAC address table . . . . . . . . . . . . . 214

Configure Layer 2 loop protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215

Configure global Layer 2 loop protection. . . . . . . . . . . . . . . . . . . . . . . 215

View and configure Layer 2 loop protection on a port . . . . . . . . . . . . 216

Chapter 4 Configure Routing

Routing concepts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220

Configure the routing mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .220

Configure the router settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220

View the IP routing statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221

Configure IPv6 routing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225

Configure the global IPv6 routing settings . . . . . . . . . . . . . . . . . . . . . . 225

View the IPv6 route table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226

Configure IPv6 VLAN interface settings. . . . . . . . . . . . . . . . . . . . . . . . . 227

Configure an IPv6 prefix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230

View the IPv6 routing statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231

View, search, or clear the IPv6 neighbor table . . . . . . . . . . . . . . . . . . . 236

Configure an IPv6 static route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238

Configure the IPv6 route preferences . . . . . . . . . . . . . . . . . . . . . . . . . . 239

Configure VLAN routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .240

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

User Manual7

Create a routing interface with the VLAN Static Routing Wizard . . . . 241

Manage a VLAN routing interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243

Delete a VLAN routing interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244

Configure router discovery for a VLAN routing interface . . . . . . . . . . 244

Manage routes and view the routing table. . . . . . . . . . . . . . . . . . . . . . . . . .246

Manually add a route and view the routing table . . . . . . . . . . . . . . . . 246

Modify a route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248

Delete a route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249

Configure Address Resolution Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . .249

View the ARP cache. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250

Manually add an entry to the ARP table. . . . . . . . . . . . . . . . . . . . . . . . . 252

View or globally configure the ARP table . . . . . . . . . . . . . . . . . . . . . . . 253

Remove ARP entries from the ARP cache . . . . . . . . . . . . . . . . . . . . . . . 254

Chapter 5 Configure Quality of Service

Quality of Service concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257

Manage the Class of Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .257

CoS configuration concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257

Configure the global CoS settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258

Configure CoS interface settings for an interface . . . . . . . . . . . . . . . . 259

Configure the CoS queue settings for an interface . . . . . . . . . . . . . . . 261

Map 802.1p priorities to queues. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262

Map DSCP values to queues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263

Manage Differentiated Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .265

Defining DiffServ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265

Configure the DiffServ mode and display the entries in the

DiffServ private MIB tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266

Configure a DiffServ class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267

Configure DiffServ IPv6 class settings . . . . . . . . . . . . . . . . . . . . . . . . . . 273

Configure a DiffServ policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278

Configure the DiffServ service interface . . . . . . . . . . . . . . . . . . . . . . . . 283

View DiffServ service statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286

Chapter 6 Manage Device Security

Change the device password for the

local browser interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289

Manage the RADIUS settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .290

Configure the global RADIUS server settings. . . . . . . . . . . . . . . . . . . . 290

Configure a RADIUS authentication server on the switch. . . . . . . . . . 292

Configure a RADIUS accounting server. . . . . . . . . . . . . . . . . . . . . . . . . 295

Configure the TACACS+ settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .298

Configure the global TACACS+ settings . . . . . . . . . . . . . . . . . . . . . . . . 299

Configure a TACACS+ server on the switch . . . . . . . . . . . . . . . . . . . . . 300

Modify the settings for a TACACS+ server on the switch . . . . . . . . . . 301

Remove a TACACS+ server from the switch . . . . . . . . . . . . . . . . . . . . . 301

Configure authentication lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .302

Configure an HTTP authentication list . . . . . . . . . . . . . . . . . . . . . . . . . . 302

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

User Manual8

Configure an HTTPS authentication list . . . . . . . . . . . . . . . . . . . . . . . . . 304

Configure the dot1x authentication list . . . . . . . . . . . . . . . . . . . . . . . . . 305

Manage the Smart Control Center Utility . . . . . . . . . . . . . . . . . . . . . . . . . . .306

Configure management access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308

Configure HTTP access settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308

Configure HTTPS access settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309

Manage certificates for HTTPS access . . . . . . . . . . . . . . . . . . . . . . . . . . 311

Control access with profiles and rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .314

Add an access profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315

Add a rule to the access profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316

Activate the access profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317

Display the access profile summary and the number of

filtered packets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318

Deactivate an access profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319

Remove an access profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320

Configure port authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .320

Configure the global 802.1X settings . . . . . . . . . . . . . . . . . . . . . . . . . . 321

Manage port authentication on individual ports . . . . . . . . . . . . . . . . . 322

View the client summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328

Set up traffic control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .329

Manage MAC filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329

Configure storm control settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332

Manage port security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336

Configure protected ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340

Manage private VLANs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341

Configure access control lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .347

Use the ACL Wizard to create a simple ACL . . . . . . . . . . . . . . . . . . . . . 347

Configure a MAC ACL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352

Configure MAC ACL rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355

Configure MAC bindings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359

View or delete MAC ACL bindings in the MAC binding table. . . . . . 360

Configure a basic or extended IPv4 ACL. . . . . . . . . . . . . . . . . . . . . . . . 361

Configure rules for a basic IPv4 ACL . . . . . . . . . . . . . . . . . . . . . . . . . . . 364

Configure rules for an extended IPv4 ACL . . . . . . . . . . . . . . . . . . . . . . 368

Configure an IPv6 ACL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376

Configure rules for an IPv6 ACL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379

Configure IP ACL interface bindings . . . . . . . . . . . . . . . . . . . . . . . . . . . 385

View or delete IP ACL bindings in the IP ACL binding table . . . . . . . 387

Configure VLAN ACL bindings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 388

Chapter 7 Monitor the Switch and the Traffic

Monitor the switch and the ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392

View or clear switch statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392

View port statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395

View and manage detailed port statistics . . . . . . . . . . . . . . . . . . . . . . . 398

View or clear EAP and EAPoL statistics . . . . . . . . . . . . . . . . . . . . . . . . . 404

Perform a cable test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

User Manual9

Configure and view the logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .407

Manage and view the memory log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407

Message log format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409

Manage and view the flash log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410

Manage the server log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412

View or clear the trap logs and the counters . . . . . . . . . . . . . . . . . . . . 415

View or clear the event log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416

Format of the messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417

Configure port mirroring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .418

Chapter 8 Maintain or Troubleshoot the Switch

Reboot the switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421

Reset the switch to its factory default settings . . . . . . . . . . . . . . . . . . . . . 422

Export a file from the switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .423

Use TFTP to export a file from the switch to a TFTP server. . . . . . . . . 423

Use HTTP to export a file from the switch to a computer . . . . . . . . . . 425

Export a file from the switch to a USB device . . . . . . . . . . . . . . . . . . . . 426

Download a file to the switch or update the software . . . . . . . . . . . . . . . .427

Use TFTP to download a file to the switch or update the

software image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427

Use HTTP to download a file to the switch or update the

software image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429

Download a file from a USB device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431

Manage software images. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .433

Copy a software image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433

Configure dual image settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434

View the dual image status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436

Perform diagnostics and troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . .437

Ping an IPv4 address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437

Ping an IPv6 address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 438

Send an IPv4 traceroute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440

Send an IPv6 traceroute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442

Enable remote diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444

Configure memory dump settings and perform a full

memory dump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445

Appendix A Configuration Examples

Virtual Local Area Networks (VLANs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449

VLAN configuration examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450

Access control lists (ACLs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .451

MAC ACL example configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451

Basic IP ACL example configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . 452

Differentiated Services (DiffServ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .453

Class. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454

DiffServ traffic classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455

Creating policies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455

DiffServ example configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

User Manual10

802.1X access control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .458

802.1X example configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 460

Multiple Spanning Tree Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .461

MSTP example configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 462

VLAN routing interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .464

Appendix B Specifications and Default Settings

Switch default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467

General feature default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .468

System setup and maintenance settings . . . . . . . . . . . . . . . . . . . . . . . . . . .475

Port characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .475

Traffic control settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .476

Quality of Service settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .476

Security settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .477

System management settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .477

Settings for other features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .478

Hardware technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 479

1Get Started

This user manual describes how you can configure and operate the following NETGEAR Gigabit

Smart Managed Pro Switches by using the local browser–based management interface:

• GS418TPP. NETGEAR Easy-Mount 16-Port Gigabit High Power PoE+ Smart Managed

Pro Switch with 2 SFP Ports (240W)

• GS510TLP. NETGEAR 8-Port Gigabit PoE+ Smart Managed Pro Switch with 2 SFP

Ports (75W)

• GS510TPP. NETGEAR 8-Port Gigabit High Power PoE+ Smart Managed Pro Switch

with 2 SFP Ports (190W)

The manual describes the software configuration procedures and explains the options that are

available within those procedures.

This chapter covers the following topics:

•Switch management and discovery overview

•Change the default IP address of the switch

•Discover or change the switch IP address

•About the user interfaces

•Access the local browser interface

•Change the language of the local browser interface

•Use the Device View of the local browser interface

•Interface naming conventions

•Configure interface settings

•Context–sensitive help and access to the support website

•Access the user manual online

•Register your product

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual12

Note: In this manual, we refer to all switch models as the switch. Unless

noted otherwise, all information applies to all switch models. We refer

to the local browser–based management interface as the local

browser interface.

Note: For more information about the topics covered in this manual, visit the

support website at netgear.com/support.

Note: Firmware updates with new features and bug fixes are made available

from time to time at netgear.com/support/download/. Some

products can regularly check the site and download new firmware, or

you can check for and download new firmware manually. If the

features or behavior of your product does not match what is described

in this guide, you might need to update your firmware.

Available publications

The following guides are available at netgear.com/support/download/:

•Installation Guide

•Hardware Installation Guide

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual13

Switch management and discovery

overview

The switch provides administrative management options that let you configure, monitor, and

control the network. Using the local browser interface, you can configure the switch and the

network, including the ports, the management VLAN, VLANs for traffic control, link

aggregation for increased bandwidth, quality of service (QoS) for prioritizing traffic, and

network security.

Initial discovery of the switch on the network requires one of the following tools:

• NETGEAR Smart Control Center (SCC) program. The SCC runs on a Windows-based

computer. You can download the SCC program from netgear.com/support/download/.

For more information about the SCC program see Discover a switch in a network with a

DHCP server on page 14 and Discover a switch in a network without a DHCP server on

page 15.

• NETGEAR Switch Discovery Tool. If you use a Mac computer, you can use the

NETGEAR Switch Discovery Tool to discover the switch in your network and access the

local browser interface of the switch. For more information about the Switch Discovery

Tool, Use the NETGEAR Switch Discovery Tool to access the switch on page 17.

• NETGEAR Insight app. You can also install the NETGEAR Insight app on an iOS or

Android mobile device and discover the IP address of the switch. For more information

about the Insight app, see Use the NETGEAR Insight app to discover and register the

switch on page 18.

You can also get the IP address of the switch from the DHCP server in the network or use an

IP scanner utility.

After discovery, you can configure the switch using the local browser interface for advanced

setup and configuration of features, or the SCC program for very basic setup. For more

information, see the SCC user manual, which you can download from

netgear.com/support/download/.

Change the default IP address of the switch

To enable remote management of the switch through a web browser or SNMP, connect the

switch to the network and specify an IP address, subnet mask, and default gateway. The

switch default IP address is 192.168.0.239 and the default subnet mask is 255.255.255.0.

To change the default IP address of the switch, use one of the following methods:

• Dynamic assignment through DHCP. DHCP is enabled on the switch by default. If you

connect the switch to a network with a DHCP server, the switch obtains its network

information automatically. You can use the Smart Control Center to discover the

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual14

automatically assigned network information. For more information, see Discover or

change the switch IP address on page 14.

• Static assignment through the Smart Control Center. If you connect the switch to a

network that does not include a DHCP server, you can use the Smart Control Center to

assign a static IP address, subnet mask, and default gateway. For more information, see

Discover a switch in a network without a DHCP server on page 15.

• Static assignment by connecting from a local host. If you do not want to use the

Smart Control Center to assign a static address, you can connect to the switch from a

host (administrative system) in the 192.168.0.0/24 network and change the settings by

using the local browser interface on the switch. For information about how to set the IP

address on the administrative system so that it is in the same subnet as the default IP

address of the switch, see Configure a static IP address from a directly connected

computer on page 19.

Discover or change the switch IP address

The following sections describe methods that let you discover or change the IP address of

the switch.

Discover a switch in a network with a DHCP server

This section describes how to set up your switch in a network that includes a DHCP server.

The DHCP client on the switch is enabled by default. When you connect the switch to your

network, the DHCP server automatically assigns an IP address to the switch. Use the Smart

Control Center (SCC) to discover the IP address automatically assigned to the switch.

Note: For more information about the SCC program, see the SCC user manual,

which you can download by visiting netgear.com/support/download/.

To install the switch in a network with a DHCP server:

1. Connect the switch to a network with a DHCP server.

2. Power on the switch by connecting its power cord.

3. Install the Smart Control Center on your computer.

4. Start the Smart Control Center.

5. Click the Discover button for the Smart Control Center to discover all the devices in the

subnet.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual15

6. Make a note of the displayed IP address assigned by the DHCP server.

You can use this address later to access the switch directly from a web browser (that is,

without using the Smart Control Center).

7. Select your switch by clicking the line that displays the switch.

8. Click the Web Browser Access button.

The Smart Control Center launches a browser that displays the login page of the selected

device.

Use your web browser to manage your switch. The default password is password. For

more information about the page layout and options, see Navigation tabs, configuration

menus, and page menu on page 22.

Discover a switch in a network without a DHCP server

This section describes how to use the Smart Control Center to set up your switch in a

network without a DHCP server. If your network does not include a DHCP service, you must

assign a static IP address to your switch.

If you prefer, you can assign the switch a static IP address even if your network does include

a DHCP server.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual16

Note: For more information about the SCC program, see the SCC user manual,

which you can download by visiting netgear.com/support/download/.

To assign a static IP address:

1. Connect the switch to your existing network.

2. Power on the switch by connecting its power cord.

3. Install the Smart Control Center on your computer.

4. Start the Smart Control Center.

5. Click the Discover button for the Smart Control Center to find your switch.

The utility broadcasts Layer 2 discovery packets within the broadcast domain to discover

the switch.

6. Select the switch, and then click the Configure Device button.

The page expands to display additional fields at the bottom.

7. Select the Disabled radio button.

DHCP is disabled.

8. Enter the static switch IP address, gateway IP address, and subnet mask for the switch.

9. Type your password to continue with the configuration change.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual17

Tip: You must enter the current password each time that you use the

Smart Control Center to update the switch settings. The default

password is password.

10. Click the Apply button.

Your settings are saved.

Use the NETGEAR Switch Discovery Tool to access the

switch

For easiest access, we recommend that you cable the switch to a network with a router or

DHCP server that assigns IP addresses, power on the switch, and then use a computer that

is connected to the same network as the switch.

The NETGEAR Switch Discovery Tool lets you discover the switch in your network and

access the local browser interface of the switch from a Mac or a 64-bit Windows-based

computer.

To install the NETGEAR Switch Discovery Tool, discover the switch in your network,

and access the local browser interface of the switch:

1. Download the Switch Discovery Tool by visiting

netgear.com/support/product/netgear-switch-discovery-tool.aspx.

Depending on the computer that you are using, download either the Mac version or the

version for a 64-bit Windows-based computer.

2. Temporarily disable the firewall, Internet security, antivirus programs, or all of these on the

computer that you use to configure the switch.

3. Unzip the Switch Discovery Tool files, double-click the .exe or .dmg file (for example,

NETGEAR+Switch+Discovery+Tool+Setup+1.2.101.exe or

NetgearSDT-V1.2.101.dmg), and install the program on your computer.

The installation process places a NETGEAR Switch Discovery Tool icon on your

desktop.

4. Reenable the security services on your computer.

5. Power on the switch.

The DHCP server assigns the switch an IP address.

6. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection. The computer and the switch must be on the

same Layer 2 network.

7. Open the Switch Discovery Tool.

To open the program, double-click the NETGEAR Switch Discovery Tool icon on your

desktop.

The initial page displays a menu and a button.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual18

8. From the Choose a connection menu, select the network connection that allows the Switch

Discovery Tool to access the switch.

9. Click the Start Searching button.

The Switch Discovery Tool displays a list of Smart Managed Plus Switches that it

discovers on the selected network.

For each switch, the tool displays the IP address.

10. To access the local browser interface of the switch, click the ADMIN PAGE button.

The login page of the local browser interface opens.

11. Enter the switch password.

The default password is password. The password is case-sensitive.

The Switch Information page displays.

Use the NETGEAR Insight app to discover and register the

switch

If the switch is connected to a WiFi router or access point, and the switch is connected to the

Internet, the NETGEAR Insight app lets you discover the switch in your network, register the

switch with NETGEAR, activate your warranty, and access support.

To use the NETGEAR Insight app to discover the switch in your network and register

the switch with NETGEAR:

1. On your iOS or Android mobile device, go to the app store, search for NETGEAR

Insight, download the latest version of the app, and install the app.

2. Connect your mobile device to the WiFi network of the WiFi router or access point to which

the switch is connected.

3. Open the NETGEAR Insight app.

4. If you did not set up a NETGEAR account, tap Create NETGEAR Account and follow the

onscreen instructions.

5. Enter the email address and password for your account and tap LOG IN.

After you log in to your account, the IP address of the switch displays in the device list.

6. Write down the IP address for future use.

7. Tap + in the upper-right corner.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual19

8. Do one of the following:

•Scan the QR code.

•Scan the serial number bar code, and tap Go.

•Type the serial number, and tap Go.

9. Follow the onscreen instructions to add your switch to a network location.

The switch is registered and added to your account.

Configure a static IP address from a directly connected

computer

If you do not want to use the Smart Control Center to configure the network information on

the switch, you can change the IP address of the switch by connecting an Ethernet cable

from a computer to the switch.The IP address of the computer must be in the same subnet as

the default IP address on the switch. For most networks, this means that you must change

the IP address of the computer to be on the same subnet as the default IP address of the

switch (192.168.0.239).

To configure a static IP address on the switch:

1. Change the IP settings of your computer to be in the same subnet as the IP settings of

the switch.

If the DHCP client of the switch is enabled and you remove the switch from the network

with the DHCP server, the IP address reverts to the default IP address of 192.168.0.239

with a subnet of 255.255.255.0.

Note: If you already disabled the DHCP client and assigned a static IP

address to the switch, change the IP settings of your computer to be in

the same subnet as the static IP address.

For more information about changing the IP settings on your computer, see one of the

following knowledge base articles at the NETGEAR website:

• Windows-based computer. See the following article:

https://kb.netgear.com/27476/How-to-set-a-static-IP-address-in-Windows

• Mac. See the following article:

https://kb.netgear.com/000037250/Setting-a-static-IP-address-on-your-network-a

dapter-in-Mac-OS-for-direct-access-to-an-access-point

(The Mac article is written for an access point but is also valid for a switch.)

2. Connect your computer to the switch using an Ethernet cable.

3. Power on the switch by connecting its power cord.

4. Launch a web browser.

5. In the address field of your web browser, enter the IP address of the switch.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual20

If you did not disable the DHCP client and assigned a static IP address to the switch,

enter 192.168.0.239.

The login window opens.

6. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

7. Select System > Management > IP Configuration.

The IP Configuration page displays.

8. Select the Static IP Address radio button.

9. Configure the IP address, subnet mask, and default gateway to be assigned to the switch.

10. Click the Apply button.

Your settings are saved.

11. Disconnect the Ethernet cable and return the network configuration on your computer to the

original settings.

About the user interfaces

The switch software includes a set of comprehensive management functions for configuring

and monitoring the system by using one of the following methods:

•Local browser interface

•Simple Network Management Protocol (SNMP)

Each of the standards-based management methods allows you to configure and monitor the

components of the switch. The method you use to manage the switch depends on your

network size and requirements, and on your preference.

This manual describes how to use the local browser interface to manage and monitor the

switch.

Requirements for the local browser interface

To access the switch by using a web browser, the browser must meet the following software

requirements:

•HTML version 4.0, or later

•HTTP version 1.1, or later

•Java Runtime Environment 1.6 or later

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual21

Supported web browsers

The following web browsers were tested and support the local browser interface. Later web

browser versions might function fine but were not tested. The supported web browsers

include the following:

•Microsoft Internet Explorer (IE) versions 10 and 11

•Microsoft Edge

•Mozilla Firefox versions 40 and 46.0.1

•Chrome version 45

•Safari on Windows OS versions 5.1 and 6.0

•Safari on MAC OS X version 8.0

Access the local browser interface

You must be able to ping the IP address of the switch from your computer for web access to

be available. If you used the Smart Control Center to set up the IP address and subnet mask,

either with or without a DHCP server, use that IP address in the address field of your web

browser. If you did not change the IP address of the switch from the default value, enter

192.168.0.239 in the address field.

You can use one of the following methods to access the switch local browser interface:

•From the Smart Control Center, select the switch and click the Web Browser Access

button.

•From the Switch Discovery Tool, select the switch and click the ADMIN PAGE button.

•Open a web browser and enter the IP address of the switch in the address field.

If you use any of these methods, the switch Login window displays.

You can use a web browser to access the switch and log in to the switch local browser

interface. To do so, you must be able to reach the IP address of the switch from your

computer.

To access the switch local browser interface from a web browser:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual22

4. If the browser does not display the login window, do the following:

•If you use a wired Ethernet connection, make sure that the computer is connected to

the same network that the switch is attached to or directly to one of the LAN Ethernet

ports of the switch.

•If you use a mobile device, make sure that mobile device is connected to an access

point that is attached to the same network that the switch is connected to or that the

access point is directly attached to one of the LAN Ethernet ports of the switch.

•Make sure that the switch is receiving power and that its Power LED is lit.

•Close and reopen the browser.

5. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

The following figure shows the layout of the local browser interface for model GS418TPP.

The layouts of the local browser interfaces for models GS510TLP and GS510TPP are

almost identical.

Navigation tab Configuration menus Logout button

Help link

Buttons

Page menu Configuration status and options

Help page

Navigation tabs, configuration menus, and page menu

The navigation tabs along the top of the local browser interface give you quick access to the

various switch functions. The tabs are always available and remain constant, regardless of

which feature you configure.

When you select a tab, the features for that tab appear as menus directly under the tabs. The

configuration menus in the blue bar change according to the navigation tab that is selected.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual23

The configuration pages for each feature are available as submenu links in the page menu

on the left side of the page. Some items in the menu expand to reveal multiple submenu

links, as the following figure shows.

Link

Submenu

links

Configuration and status options

The area directly under the configuration menus and to the right of the links displays the

configuration information or status for the page you select. On pages that contain

configuration options, you might be able to enter information into fields, select options from

menus, select check boxes, and select radio buttons.

Each page contains access to the HTML-based help that explains the fields and

configuration options for the page.

Buttons in the local browser interface

Each page also contains command buttons. The following table shows the command buttons

that are used throughout the pages in the local browser interface:

Table 1. Local browser interface buttons

Button Function

Add Clicking the Add button adds the new item configured in the heading row of a table.

Apply Clicking the Apply button saves your settings. Configuration changes take effect immediately.

Cancel Clicking the Cancel button cancels the configuration on the page and resets the data on the

page to the previous values of the switch.

Delete Clicking the Delete button removes the selected item.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual24

User-defined fields

User-defined fields can contain 1 to 159 characters, unless otherwise noted on the

configuration web page. All characters can be used except for the ones stated in the following

table (unless specifically noted in a procedure for a feature).

Table 2. Invalid characters for user-defined fields

Invalid Characters for user-defined fields

\ <

/ >

* |

Change the language of the local browser

interface

By default, the language is set to Auto. You can set the language to a specific one.

To change the language of the local browser interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

Update Clicking the Update button refreshes the page with the latest information from the device.

Logout Clicking the Logout button ends the session.

Table 1. Local browser interface buttons (continued)

Button Function

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual25

The System Information page displays.

5. At the top of the page, select a language from the language menu.

A confirmation pop-up window opens.

6. Click the OK button to confirm.

The switch restarts and you must log in again.

The language of the local browser interface is now set to the language that you selected.

Use the Device View of the local browser

interface

The Device View is a Java® applet that displays the ports on the switch. This graphic tool

provides an alternate way to navigate to configuration and monitoring options. The graphic

tool also provides information about device ports, configuration and status, tables, and

feature components.

To use the Device View:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Device View.

The Device View page displays.

The following figure shows the Device View page for model GS418TPP.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual26

Depending upon the status of the port, the port color in Device View is either red, green,

or black.

•Green indicates that the port is linking up.

•Red indicates that an error occurred on the port or that the port is administratively

disabled.

•Black indicates that no link is present.

Each port also provides two LEDs in Device View to indicate the link status of the port.

•The left green LED indicates that the port is linking at a speed of 10G.

•The right yellow LED indicates that the port is linking at a speed of 1G or 100 Mbps.

6. Click a port to open a menu that displays statistics and configuration options.

You can select a menu option to access the page that contains the configuration or

monitoring options.

If you right-click the graphic, but do not right-click a specific port, the main menu displays.

This menu contains the same options as the navigation tabs at the top of the page.

The following figure shows the details on the Device View page for model GS418TPP.

Right-click the specific port that you want to view or configure to see a menu that displays

statistics and configuration options. Select the menu option to access the page that

contains the configuration or monitoring options.

The system LEDs are located on the left side of the front panel.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual27

Power LED

The Power LED is a bicolor LED that serves as an indicator of power. For the Device View,

the only option is solid green, which indicates that power is supplied to the switch and

operating normally.

Fan LED

The Fan LED indicates the following status:

• Solid yellow. The fan is faulty.

•Off. The fan is operating normally.

Interface naming conventions

The switch supports physical and logical interfaces. Interfaces are identified by their type and

the interface number. The physical ports are Gigabit interfaces and are numbered on the

front panel. You configure the logical interfaces by using the software.

The following table describes the naming convention for all interfaces available on the switch.

Table 3. Naming conventions for interfaces

Interface Description Example

Physical The physical ports are Gigabit Ethernet interfaces

and are numbered sequentially starting from 1. g1, g2, g12

Link aggregation group (LAG) LAG interfaces are logical interfaces that are used

only for bridging functions. l1, l2, l3

CPU management interface This is the internal switch interface responsible for

the switch base MAC address. This interface is

not configurable and is always listed in the MAC

Address Table.

Routing VLAN interfaces This is an interface used for routing functionality. VLAN 1, VLAN 2, VLAN 3

Configure interface settings

For some features that allow you to configure interface settings, you can apply the same

settings simultaneously to any of the following:

•A single port

•Multiple ports

•All ports

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual28

•A single LAG

•Multiple LAGs

•All LAGs

•Multiple ports and LAGs

•All ports and LAGs

Many of the pages that allow you to configure or view interface settings include links to

display all ports, all LAGs, or all ports and LAGs on the page.

Use these links as follows:

•To display all ports, click the 1 link.

•To display all LAGs, click the LAGS link.

•To display all ports and LAGs, click the All link.

The procedures in this section describe how to select the ports and LAGs to configure. The

procedures assume that you are already logged in to the switch. If you do not know how to

To configure a single port by using the Go To Interface field:

1. Ensure that the page is displaying all ports, and not only the LAGs.

2. In the Go To Interface field, type the port number.

For example, type g4.

For more information, see Interface naming conventions on page 27.

3. Click the Go button.

The check box associated with the interface is selected, the row for the selected interface

is highlighted, and the interface number displays in the heading row.

4. Configure the desired settings.

5. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual29

To configure a single LAG by using the Go To Interface field:

1. Click the LAGS link or the All link to display the LAGs.

2. In the Go To Interface field, type the LAG number, for example l3.

For information, see Interface naming conventions on page 27.

3. Click the Go button.

The check box associated with the interface is selected, the row for the selected interface

is highlighted, and the interface number appears in the heading row.

4. Configure the desired settings.

5. Click the Apply button.

Your settings are saved.

To configure a single port:

1. Ensure that the page is displaying all ports, and not only the LAGs.

2. Select the check box next to the port number.

The row for the selected interface is highlighted, and the interface number appears in the

heading row.

3. Configure the desired settings.

4. Click the Apply button.

Your settings are saved.

To configure a single LAG:

1. Click the LAGS link or the All link to display the LAGs.

2. Select the check box next to the LAG number.

The row for the selected interface is highlighted, and the interface number appears in the

heading row.

3. Configure the desired settings.

4. Click the Apply button.

Your settings are saved.

To configure multiple ports:

1. Ensure that the page is displaying all ports, and not only the LAGs.

2. Select the check box next to each port to configure.

The row for each selected interface is highlighted.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual30

3. Configure the desired settings.

4. Click the Apply button.

Your settings are saved.

To configure multiple LAGs:

1. Click the LAGS link or the All link to display the LAGs.

2. Select the check box next to each LAG to configure.

The check box associated with each interface is selected, and the row for each selected

interface is highlighted.

3. Configure the desired settings.

4. Click the Apply button.

Your settings are saved.

To configure all ports:

1. Ensure that the page is displaying only ports, and not LAGs.

2. Select the check box in the heading row.

The check boxes for all ports are selected and the rows for all ports are highlighted.

3. Configure the desired settings.

4. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual31

To configure all LAGs:

1. Click the LAGS link to display only the LAG interfaces.

2. Select the check box in the heading row.

The check box associated with every LAG is selected, and the rows for all LAGs are

highlighted.

3. Configure the desired settings.

4. Click the Apply button.

Your settings are saved.

To configure multiple ports and LAGs:

1. Click the All link to display all ports and LAGs.

2. Select the check box associated with each port and LAG to configure.

The rows for the selected ports and LAGs are highlighted.

3. Configure the desired settings.

4. Click the Apply button.

Your settings are saved.

To configure all ports and LAGs:

1. Click the All link to display all ports and LAGs.

2. Select the check box in the heading row.

The check box associated with every port and LAG is selected, and the rows for all ports

and LAGs are highlighted.

3. Configure the desired settings.

4. Click the Apply button.

Your settings are saved.

Context–sensitive help and access to the

support website

When you log in to the switch, every page contains a link to the online help ( ) that contains

information to assist in configuring and managing the switch. The online help pages are

context sensitive. For example, if the IP Addressing page is open, the help topic for that page

displays if you click the link to the online help.

From the local browser interface, you can access the NETGEAR support website at

www.netgear.com/support.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual32

To access the support website from the local browser interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Help > Support.

The Support page displays.

6. To access the NETGEAR support site for the switch, click the Apply button.

Access the user manual online

The user manual (the guide you are now reading) is available at the NETGEAR download

center at netgear.com/support/download/.

To access the user manual online from the local browser interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The Switch Information page displays.

5. Select Help > Online Help > User Guide.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Get Started User Manual33

The User Guide page displays.

6. To access the NETGEAR download center, click the Apply button.

7. Enter the model number of the switch.

8. Locate the user manual on the product support web page.

To qualify for product updates and product warranty, we encourage you to register your

product. The first time you log in to the switch, you can register with NETGEAR. Registration

confirms that your email alerts work, lowers technical support resolution time, and ensures

that your shipping address accuracy. We would also like to incorporate your feedback into

future product development. We never sell or rent your email address and you can opt out of

communications at any time.

To register with NETGEAR when you are prompted, click the REGISTER NOW button. Or at

any time you can visit the NETGEAR website for registration at

https://my.netgear.com/registration/login.aspx.

You can also use the NETGEAR Insight app to register your product (see Use the NETGEAR

Insight app to discover and register the switch on page 18.

2Configure System Information

This chapter covers the following topics:

•View or define system information

•Configure the IP network settings for management access

•Configure the time settings

•Configure denial of service settings

•Configure the DNS settings

•Configure green Ethernet settings

•Use the Device View

•Configure Power over Ethernet

•Configure SNMP

•Configure LLDP

•Configure a DHCP L2 relay, DHCP snooping, and dynamic ARP inspection

•Set up PoE timer schedules

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual35

View or define system information

When you log in, the System Information page displays. Use this page to configure and view

general device information.

To view or define system information:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

5. Define the following fields:

• System Name. Enter the name to identify this switch. You can use up to 255

alphanumeric characters. The default is blank.

• System Location. Enter the location of this switch. You can use up to 255

alphanumeric characters. The default is blank.

• System Contact. Enter the contact person for this switch. You can use up to 255

alphanumeric characters. The default is blank.

6. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual36

The following table describes the status information that the System Information page

displays.

Table 4. System Information

Field Description

Product Name The product name of this switch.

Serial Number The serial number of the switch.

System Object OID The base object ID for the switch's enterprise MIB.

Date & Time The current date and time.

System Up Time The time in days, hours, and minutes since the last switch reboot.

Base Mac Address Universally assigned hardware address of the switch.

Temp (C) The general temperature of the switch in degrees Centigrade.

Temperature traps range Identifies the minimum and maximum traps range.

View the temperature sensor information

Note: The temperature sensor information is available for model GS418TPP

only.

You can view the current temperature of the temperature sensors. The temperature is instant

and can be updated with the latest information about the switch when you click the Update

button. The maximum temperature of the temperature sensors depends on the actual

hardware.

To view temperature information:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual37

The System Information page displays.

5. Scroll down to the Temperature Sensors section.

6. To refresh the page, click the Update button.

The following table describes the nonconfigurable Temperature Sensors information.

Table 5. Temperature Sensors information

Field Description

Sensor The temperature sensor for the given unit.

Description The description of the temperature sensor.

Temp(C) The temperature of the specified unit in degrees Centigrade.

State The unit temperature state.

Max Temp (C) The maximum temperature value of CPU and MACs. Once the blade

exceeds this limit, the chassis shuts down the power for this blade.

View the fan status

Note: The fan status information is available for models GS418TPP and

GS510TPP only.

You can view the status of the fans in all units. These fans remove the heat generated by the

power, CPU, and other components, and allow the switch to function normally.

To view the fan status:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual38

The System Information page displays.

5. Scroll down to the Fans section.

6. To refresh the page, click the Update button.

The following table describes the nonconfigurable fan status information.

Table 6. Fan status

Field Description

FAN The fan index used to identify the fan for the switch.

Description The description of the temperature sensor.

Type Specifies whether the fan module is fixed or removable.

Speed The fan speed.

Duty level(%) The duty level of the fan.

State Specifies whether the fan is operational.

View the status of the power supplies

You can view s the status of the power supplies.

To view the power supplies status:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Scroll down to the Power supplies section.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual39

6. To refresh the page, click the Update button.

The following table describes the nonconfigurable Power supplies information.

Table 7. Power supplies status

Field Description

Power supply The power supply index used for the unit.

Description The description of the power supply.

Type Specifies whether the power module is fixed or removable.

State Specifies the state of the power module.

View the software versions

You can view the software versions that are running on the switch.

To view the software versions:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Scroll down to the Versions section.

6. To refresh the page, click the Update button.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual40

The following table describes the nonconfigurable information displayed in the Versions

section of the System Information page.

Table 8. Versions information

Field Description

Model Name The model name of the switch.

Boot Version The version of the bootloader software of the switch.

Software Version The version number of the code currently running on the switch.

View the system CPU status

You can monitor the CPU, memory resources, and utilization patterns across various

intervals to assess the performance, load, and stability settings.

To view the system CPU status:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > System CPU Status > System CPU Status.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual41

The CPU Utilization section shows the memory information, task-related information, and

percentage of CPU utilization per task.

The following table describes CPU Memory Status information.

Table 9. CPU Memory Status information

Field Description

Total System Memory The total memory of the switch in KBytes.

Available Memory The available memory space for the switch in KBytes.

Configure the CPU thresholds

The CPU Utilization Threshold notification feature allows you to configure thresholds that,

when exceeded, trigger a notification. The notification occurs through SNMP trap and syslog

messages.

To configure the CPU thresholds:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual42

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > System CPU Status > CPU Threshold.

6. Specify the thresholds:

• Rising Threshold. Notification is generated when the total CPU utilization exceeds

this threshold value over the configured time period. The range is 1 to 100.

• Rising Interval. This utilization monitoring time period can be configured from 5 to

86400 seconds in multiples of 5 seconds.

• Falling Threshold. Notification is triggered when the total CPU utilization falls below

this level for a configured period of time.

The falling utilization threshold must be equal to or less than the rising threshold

value. The falling utilization threshold notification is sent only if a rising threshold

notification was sent previously. Configuring the falling utilization threshold and time

period is optional. If the Falling CPU utilization settings are not configured, the

settings automatically get the same values as the Rising CPU utilization settings. The

range is 1 to 100.

• Falling Interval. The utilization monitoring time period can be configured from 5

seconds to 86400 seconds in multiples of 5 seconds.

• Free Memory Threshold. The free memory threshold value for the CPU in KB.

7. Click the Apply button.

Your settings are saved.

View the USB device information

Note: Model GS418TPP supports a USB port but models GS510TLP and

GS510TPP do not. Therefore, the information in this section refers to

model GS418TPP only.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual43

You can display the USB device status, memory statistics, and directory details.

The limitations for the USB device supported on the switch are as follows:

•The USB disk must comply with the USB 2.0 standard.

•The USB disk must be file type FAT32 or VFAT. File type NTFS is not supported.

To display the USB device information:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > USB Device Information.

The Device Status field displays the current status of the device. The status is one of the

following:

• Active. The device is USB plugged in and recognized by the switch.

• Inactive. The device is not mounted.

• Invalid. The device is not present or an invalid device is plugged in.

6. To refresh the page, click the Update button.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual44

The following table describes the USB Memory Statistics information.

Table 10. USB Memory Statistics information

Field Description

Total Size The USB flash device storage size in bytes.

Bytes Used The size of memory used on the USB flash device.

Bytes Free The size of memory free on the USB flash device.

The following table describes the USB Directory Details information.

Table 11. USB directory details information

Field Description

File Name The name of the file stored in the USB flash drive.

File Size The size, in bytes, of the file stored in the USB flash drive.

Modification T ime The last modification time of the file stored in the USB flash drive.

Configure the IP network settings for

management access

You can configure network information for the local browser interface, which is the logical

interface used for in-band connectivity with the switch through any of the switch’s front-panel

ports. The settings associated with the local browser interface do not affect the configuration

of the front panel ports through which traffic is switched or routed.

Configure the IPv4 network and VLAN settings for the

local browser interface

You can configure the IPv4 network information for the local browser interface, which is the

logical interface used for in-band connectivity with the switch through any of the switch’s

front-panel ports.

To configure the IPv4 network and VLAN settings for the local browser interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual45

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > IP Configuration.

The IP Configuration page displays.

6. Select the appropriate radio button to determine how to configure the network information for

the local browser interface:

• Dynamic IP Address (DHCP). Specifies that the switch must obtain the IP address

through a DHCP server.

•Dynamic IP Address (BOOTP). Specifies that the switch must obtain the IP address

through a BootP server.

•Static IP Address. Specifies that the IP address, subnet mask, and default gateway

must be manually configured. Enter this information in the fields below this radio

button.

7. If you selected the Static IP Address radio button, configure the following network

information:

• IP Address. The IP address of the network interface. The default value is

192.168.0.239. Each part of the IP address must start with a number other than zero.

For example, IP addresses 001.100.192.6 and 192.001.10.3 are not valid.

• Subnet Mask. The IP subnet mask for the interface. The default value is

255.255.255.0.

• Default Gateway. The default gateway for the IP interface. The default value is

192.168.0.254.

8. Specify the VLAN ID for the management VLAN.

The management VLAN is used to establish an IP connection to the switch from a

workstation that is connected to a port in the same VLAN. If not specified, the active

management VLAN ID is 1 (default), which allows an IP connection to be established

through any port.

When the management VLAN is set to a different value, an IP connection can be made

only through a port that is part of the management VLAN. Also, the port VLAN ID (PVID)

of the port to be connected in that management VLAN must be the same as the

management VLAN ID.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual46

Note: Make sure that the VLAN that must be the management VLAN exists.

Also make sure that the PVID of at least one port in the VLAN is the

same as the management VLAN ID. For information about creating

VLANs and configuring the PVID for a port, see Configure VLANs on

page 139.

The following requirements apply to the management VLAN:

•Only one management VLAN can be active at a time.

•When a new management VLAN is configured, connectivity through the existing

management VLAN is lost.

•The management station must be reconnected to the port in the new management

VLAN.

9. Click the Apply button.

Your settings are saved.

Configure the IPv6 network settings for the local browser

interface

You can configure the IPv6 management access settings.

To access the switch over an IPv6 network, you must initially configure the switch with IPv6

information (IPv6 prefix, prefix length, and default gateway). IPv6 can be configured using

any of the following options:

•IPv6 auto-configuration

•DHCPv6

When in-band connectivity is established, IPv6 information can be changed using

SNMP-based management or web-based management.

To configure the IPv6 network settings for the local browser interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual47

The default password is password.

The System Information page displays.

5. Select System > Management > IPv6 Network Configuration.

The IPv6 Network Global Configuration page displays.

6. Ensure that the Admin Mode Enable radio button is selected.

7. Determine how the switch acquires an IPv6 address:

• IPv6 Address Auto Configuration Mode. When this mode is enabled, the network

interface can acquire an IPv6 address through IPv6 Neighbor Discovery Protocol

(NDP) and through the use of router advertisement messages. When this mode is

disabled, the network interface does not use the native IPv6 address

auto-configuration features to acquire an IPv6 address. Auto-configuration can be

enabled only when DHCPv6 is not enabled on any of the management interfaces.

• DHCPv6. Next to Current Network Configuration Protocol, select the DHCPv6 radio

button to enable the DHCPv6 client on the interface. The switch attempts to acquire

network information from a DHCPv6 server. Selecting the None radio button disables

the DHCPv6 client on the network interface.

When DHCPv6 is enabled, the DHCPv6 Client DUID field displays the client identifier

used by the DHCPv6 client (if enabled) when sending messages to the DHCPv6

server.

8. In the IPv6 Gateway field, specify the default gateway for the IPv6 network interface.

The gateway address is in IPv6 global or link-local address format.

9. To configure one or more static IPv6 addresses for the local browser interface, do the

following:

a. In the IPv6 Prefix/Prefix Length field, specify the static IPv6 prefix and prefix to the

IPv6 network interface.

The address is in the global address format.

b. In the EUI64 menu, select True to enable the Extended Universal Identifier (EUI)

flag for IPv6 address, or select False to omit the EUI flag.

c. Click the Add button.

10. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual48

View the IPv6 network neighbor

You can view information about the IPv6 neighbors that the switch discovered through the

network interface by using the Neighbor Discovery Protocol (NDP).

To view the IPv6 Network Neighbor Table:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > IPv6 Network Neighbor.

The following table describes the information the IPv6 Network Neighbor page displays about

each IPv6 neighbor that the switch discovered.

Table 12. IPv6 network interface neighbor table information

Field Description

IPv6 address The IPv6 address of a neighbor switch visible to the network interface.

MAC address The MAC address of a neighbor switch.

IsRtr • true (1). The neighbor machine is a router.

• false

(2). The neighbor machine is not a router.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual49

Configure the time settings

The switch supports the Simple Network Time Protocol (SNTP). This is a less complicated

version of Network Time Protocol, which is a system for synchronizing the clocks of

networked computer systems, primarily when data transfer is handled through the Internet.

You can also set the system time manually.

Configure the time setting manually

You can view and adjust date and time settings.

To manually configure the time setting:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > Time > Time Configuration.

Neighbor State The state of the neighboring switch:

• reachable (1). The neighbor is reachable by this switch.

• stale

(2). Information about the neighbor is scheduled for deletion.

• delay (3). No information was received from the neighbor during

the delay period.

• probe (4). The switch is attempting to probe for this neighbor.

• unknown (5). Unknown status.

Last Updated The last sysUpTime that this neighbor was updated.

Table 12. IPv6 network interface neighbor table information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual50

6. Select the Clock Source Local radio button.

7. In the Date field, specify the current date in months, days, and years (MM/DD/YYYY).

8. In the Time field, specify the current time in hours, minutes, and seconds (HH:MM:SS).

Note: If you do not enter a date and time, the switch calculates the date and

time using the CPU’s clock cycle.

9. Click the Apply button.

Your settings are saved.

Configure the time settings with SNTP

To configure the time by using SNTP:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > Time > Time Configuration.

The Time Configuration page displays.

6. Select the Clock Source SNTP radio button.

The page refreshes and displays the SNTP Global Configuration section and the SNTP

Global Status section.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual51

The default is SNTP. The local clock can be set to SNTP only if the following two

conditions are met:

•The SNTP server is configured.

•The SNTP last attempt status is successful.

7. Next to Client Mode, select the mode of operation of the SNTP client:

• Disable. SNTP is not operational. No SNTP requests are sent from the client nor are

any incoming SNTP messages processed.

• Unicast. SNTP operates in a point-to-point fashion. A unicast client sends a request

to a designated server at its unicast address and expects a reply from which it can

determine the time and, optionally, the round-trip delay and local clock offset relative

to the server.

• Broadcast. SNTP operates in the same manner as multicast mode but uses a local

broadcast address instead of a multicast address. The broadcast address provides a

single-subnet scope while a multicast address provides an Internet-wide scope.

The default value is Disable.

8. If the SNTP client mode is Unicast, use the SNTP Server Configuration page to add the IP

address or DNS name of one or more SNTP servers for the switch to poll.

For more information, see Configure an SNTP server on page 56.

9. In the Port field, specify the local UDP port that the SNTP client receives server packets on.

The allowed range is 1025 to 65535 and 123. The default value is 123. When the default

value is configured, the actual client port value used in SNTP packets is assigned by the

operating system.

10. In the Unicast Poll Interval field, specify the number of seconds between unicast poll

requests expressed as a power of 2. to The allowed range is 6 to 10. The default value is 6.

11. In the Broadcast Poll Interval field, specify the number of seconds between broadcast poll

requests expressed as a power of 2.

Broadcasts received prior to the expiry of this interval are discarded. The allowed range is

6 to 10. The default value is 6.

12. In the Unicast Poll Timeout field, specify the number of seconds to wait for an SNTP

response to a unicast poll request.

The allowed range is 1 to 30. The default value is 5.

13. In the Unicast Poll Retry field, specify the number of times to retry a unicast poll request to

an SNTP server after the first time-out before the switch attempts to use the next configured

server.

The allowed range is 0 to 10. The default value is 1.

14. In the Time Zone Name field, specify a time zone.

You can also specify the number of hours and number of minutes that the time zone is

different from the Coordinated Universal Time (UTC). The time zone can affect the

display of the current system time. The default value is UTC.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual52

Note: When using SNTP/NTP time servers to update the switch’s clock, the

time data received from the server is based on the UTC, which is the

same as Greenwich Mean Time (GMT). This might not be the time

zone in which the switch is located.

15. In the Offset Hours field, specify the number of hours that the time zone is different from

UTC.

See the description for Time Zone Name in Step 14 for more information. The allowed

range is –12 to 13. The default value is 0.

16. In the Offset Minutes field, specify the number of minutes that the time zone is different

from UTC.

See the description for Time Zone Name in Step 14 for more information. The allowed

range is 0 to 59. The default value is 0.

17. Click the Apply button.

Your settings are saved.

Configure the global SNTP settings

To configure the global SNTP settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > Time > Time Configuration > SNTP Global

Configuration.

When you select the SNTP option as the clock source, the SNTP Global Configuration

section is displayed below the Time Configuration section of the page.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual53

6. Select a Client mode radio button to specify the mode of operation of the SNTP client:

• Disable. SNTP is not operational. No SNTP requests are sent from the client and no

received SNTP messages are processed.

• Unicast. SNTP operates in a point-to-point fashion. A unicast client sends a request

to a designated server at its unicast address and expects a reply from which it can

determine the time and, optionally, the round-trip delay and local clock offset relative

to the server.

• Broadcast. SNTP operates in the same manner as multicast mode but uses a local

broadcast address instead of a multicast address. The broadcast address provides a

single-subnet scope while a multicast address provides an Internet-wide scope.

The default value is Unicast.

7. In the Port field, specify the local UDP port that the SNTP client receives server packets on.

The allowed range is 1025 to 65535 and the value 123. The default value is 123. When

the default value is configured, the actual client port value used in SNTP packets is

assigned by the operating system.

8. In the Unicast Poll Interval field, specify the number of seconds between unicast poll

requests expressed as a power of 2.

The allowed range is 6 to 10. The default value is 6.

9. In the Broadcast Poll Interval field, specify the number of seconds between broadcast poll

requests expressed as a power of 2.

Broadcasts received prior to the expiry of this interval are discarded. The allowed range is

6 to 10. The default value is 6.

10. In the Unicast Poll Timeout field, specify the number of seconds to wait for an SNTP

response to a unicast poll request.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual54

The allowed range is 1 to 30. The default value is 5.

11. In the Unicast Poll Retry field, specify the number of times to retry a unicast poll request to

an SNTP server after the first time-out before the switch attempts to use the next configured

server.

The allowed range is 0 to 10. The default value is 1.

12. In the Time Zone Name field, specify a time zone.

You can also specify the number of hours and number of minutes that the time zone is

different from the Coordinated Universal Time (UTC). The time zone can affect the

display of the current system time. The default value is UTC.

Note: When using SNTP/NTP time servers to update the switch’s clock, the

time data received from the server is based on the UTC, which is the

same as Greenwich Mean Time (GMT). This might not be the time

zone in which the switch is located.

13. In the Offset Hours field, specify the number of hours that the time zone is different from

UTC.

The allowed range is –12 to 13. The default value is 0.

14. In the Offset Minutes field, specify the number of minutes that the time zone is different

from UTC.

The allowed range is 0 to 59. The default value is 0.

15. Click the Apply button.

Your settings are saved.

16. To refresh the page, click the Update button.

View the SNTP global status

When you select the SNTP option as the clock source, the SNTP global status is displayed

below the SNTP Global Configuration section of the page. The SNTP Global Status table

displays information about the system’s SNTP client.

To view the SNTP global status:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual55

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > Time > Time Configuration > SNTP Global Status.

When you select the SNTP option as the clock source, the SNTP Global Status is

displayed below the SNTP Global Configuration section.

6. Click the Update button to update the page with the latest information about the switch.

The following table displays the nonconfigurable SNTP Global Status information.

Table 13. SNTP Global Status information

Field Description

Version The SNTP version that the client supports.

Supported mode The SNTP modes that the client supports. Multiple modes can be supported by

a client.

Last Update Time The local date and time (UTC) that the SNTP client last updated the system

clock.

Last Attempt T ime The local date and time (UTC) of the last SNTP request or receipt of an

unsolicited message.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual56

Configure an SNTP server

SNTP assures accurate network device clock time synchronization up to the millisecond.

Time synchronization is performed by a network SNTP server. The switch operates only as

an SNTP client and cannot provide time services to other systems.

Time sources are established by strata. Strata define the accuracy of the reference clock.

The higher the stratum (where zero is the highest), the more accurate the clock. The device

receives time from Stratum 1 and above since it is itself a Stratum 2 device.

Last Attempt Status The status of the last SNTP request or unsolicited message for both unicast

and broadcast modes. If no message was received from a server, a status of

Other is displayed. These values are appropriate for all operational modes.

• Other. The status of the last request is unknown.

• Success. The SNTP operation was successful and the system time was

updated.

• Request Timed Out. After an SNTP request was sent to an SNTP server,

the response timer expired before a response from the server was

received.

• Bad Date Encoded. The time provided by the SNTP server is not valid.

• Version Not Supported. The SNTP version supported by the server is

not compatible with the version supported by the client.

• Server Unsynchronized. The SNTP server is not synchronized with its

peers. This is indicated by the leap indicator field in the SNTP message.

• Server Kiss Of Death. The SNTP server indicated that no further queries

were to be sent to this server. This is indicated by a stratum field equal to

0 in a message received from a server.

Server IP Address The IP address of the server for the last received valid packet. If no message

was received from any server, an empty string is shown.

Address Type The address type of the SNTP server address for the last received valid

packet.

Server Stratum The claimed stratum of the server for the last received valid packet.

Reference Clock ID The reference clock identifier of the server for the last received valid packet.

Server mode The mode of the server for the last received valid packet.

Unicast Server Max Entries The maximum number of unicast server entries that can be configured on this

client.

Unicast Server Current Entries The number of current valid unicast server entries configured for this client.

Broadcast Count The number of unsolicited broadcast SNTP messages that were received and

processed by the SNTP client since the last reboot.

Table 13. SNTP Global Status information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual57

The following is an example of strata:

• Stratum 0. A real-time clock is used as the time source, for example, a GPS system.

• Stratum 1. A server that is directly linked to a Stratum 0 time source is used. Stratum 1

time servers provide primary network time standards.

• Stratum 2. The time source is distanced from the Stratum 1 server over a network path.

For example, a Stratum 2 server receives the time over a network link, through NTP, from

a Stratum 1 server.

Information received from SNTP servers is evaluated based on the time level and server

type.

SNTP time definitions are assessed and determined by the following time levels:

•T1. Time that the original request was sent by the client.

•T2. Time that the original request was received by the server.

•T

3. Time that the server sent a reply.

•T

4. Time that the client received the server's reply.

The device can poll unicast server types for the server time.

Polling for unicast information is used for polling a server for which the IP address is known.

SNTP servers that were configured on the device are the only ones that are polled for

synchronization information. T1 through T4 are used to determine server time. This is the

preferred method for synchronizing device time because it is the most secure method. If this

method is selected, SNTP information is accepted only from SNTP servers defined on the

device using the SNTP Server Configuration page.

The device retrieves synchronization information, either by actively requesting information or

at every poll interval.

You can view and modify information for adding and modifying Simple Network Time

Protocol SNTP servers.

Add an SNTP server

To add an SNTP server:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual58

The default password is password.

The System Information page displays.

5. Select System > Management > Time > SNTP Server Configuration.

6. From the Server Type menu, select the type of SNTP address to enter in the address field.

The address can be either an IP address (IPv4, IPv6) or a host name (DNS). The default

value is IPv4.

7. In the Address field, specify the IP address or the host name of the SNTP server.

This is a text string of up to 64 characters, containing the encoded unicast IP address or

host name of an SNTP server. Unicast SNTP requests are sent to this address. If this

address is a DNS host name, then that host name is resolved into an IP address each

time an SNTP request is sent to it.

8. If the UDP port on the SNTP server to which SNTP requests are sent is not the standard

port (123), specify the port number in the Port field.

The valid range is 1 to 65535. The default value is 123.

9. In Priority field, specify the priority order which to query the servers.

The SNTP client on the device continues sending SNTP requests to different servers until

a successful response is received, or all servers are exhausted. The priority indicates the

order in which to query the servers. The request is sent to an SNTP server with a priority

value of 1 first, then to a server with a priority value of 2, and so on. If any servers are

assigned the same priority, the SNTP client contacts the servers in the order that they

appear in the table. The valid range is 1 to 3. The default value is 1.

10. In the Version field, specify the NTP version running on the server.

The range is 1 to 4. The default value is 4.

11. Click the Add button.

The SNTP server entry is added.

12. Repeat the previous steps to add additional SNTP servers.

You can configure up to three SNTP servers.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual59

The SNTP Server Status table displays status information about the SNTP servers

configured on your switch. The following table describes the SNTP Server Global Status

information.

Table 14. SNTP Server Status information

Field Description

Address All the existing server addresses. If no server configuration exists, a message stating

that no SNTP server exists displays on the page.

Last Update Time The local date and time (UTC) that the response from this server was used to update

the system clock.

Last Attempt T ime The local date and time (UTC) that this SNTP server was last queried.

Last Attempt Status The status of the last SNTP request or unsolicited message for both unicast and

broadcast modes. If no message was received from a server, a status of Other is

displayed. These values are appropriate for all operational modes:

Requests The number of SNTP requests made to this server since last agent reboot.

Failed Requests The number of failed SNTP requests made to this server since the last reboot.

Change the settings for an existing SNTP server

To change the settings for an existing SNTP server:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

• Other. The status of the last request is unknown, or no SNTP responses were

received.

• Success. The SNTP operation was successful and the system time was updated.

• Request Timed Out. After an SNTP request was sent to an SNTP server, the

response timer expired before a response from the server was received.

• Bad Date Encoded. The time provided by the SNTP server is not valid.

• Version Not Supported. The SNTP version supported by the server is not

compatible with the version supported by the client.

• Server Unsynchronized. The SNTP server is not synchronized with its peers. This

is indicated by the leap indicator field on the SNTP message.

• Server Kiss Of Death. The SNTP server indicated that no further queries were to

be sent to this server. This is indicated by a stratum field equal to 0 in a message

received from a server.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual60

The default password is password.

The System Information page displays.

5. Select System > Management > Time > SNTP Server Configuration.

The SNTP Server Configuration page displays.

6. Select the check box next to the configured server.

7. Specify new values in the available fields.

8. Click the Apply button.

Your settings are saved.

Remove an SNTP server

To remove an SNTP server:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > Time > SNTP Server Configuration.

The SNTP Server Configuration page displays.

6. Select the check box next to the configured server to remove.

7. Click the Delete button.

The entry is removed, and the device is updated.

Configure daylight saving time settings

You can configure settings for summer time, which is also known as daylight saving time.

Used in some countries around the world, summer time is the practice of temporarily

advancing clocks during the summer months. Typically clocks are adjusted forward one or

more hours near the start of spring and are adjusted backward in autumn.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual61

To configure the daylight saving time settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > Time > Daylight Saving Configuration.

6. Select a Daylight Saving (DST) radio button:

• Disable. Disable daylight saving time.

• Recurring. Daylight saving time occurs at the same time every year. The start and

end times and dates for the time shift must be manually configured.

• Recurring EU. The system clock uses the standard recurring summer time settings

used in countries in the European Union. When this option is selected, the rest of the

applicable fields on the page are automatically populated and cannot be edited.

• Recurring USA. The system clock uses the standard recurring daylight saving time

settings used in the United States. When this option is selected, the rest of the

applicable fields on the page are automatically populated and cannot be edited.

• Non Recurring. Daylight saving time settings are in effect only between the start date

and end date of the specified year. When this option is selected, the summer time

settings do not repeat on an annual basis.

7. Click the Apply button.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual62

Your settings are saved.

The fields in the following tables are visible only when the DayLight Saving (DST) Recurring,

Recurring EU, or Recurring USA radio button is selected.

Table 15. Daylight saving setting is Recurring, Recurring EU, or Recurring USA

Field Description

Begins At These fields are used to configure the start values of the date and time.

Ends At These fields are used to configure the end values of date and time.

Offset Configure recurring offset in minutes. The valid range is 1–1440

minutes.

Zone Configure the time zone.

The fields in the following table are visible only when the DayLight Saving (DST) Non

Recurring radio button is selected.

• Week. Configure the start week.

• Day. Configure the start day.

• Month. Configure the start month.

• Hours. Configure the start hours.

• Minutes. Configure the start minutes.

• Week. Configure the end week.

• Day. Configure the end day.

• Month. Configure the end month.

• Hours. Configure the end hours.

• Minutes. Configure the end minutes.

Table 16. Daylight saving setting is Non Recurring

Field Description

Begins At These fields are used to configure the start values of the date and time.

• Week. Configure the start week.

• Day. Configure the start day.

• Month. Configure the start month.

• Hours. Configure the start hours.

• Minutes. Configure the start minutes.

Ends At These fields are used to configure the end values of date and time.

• Week. Configure the end week.

• Day. Configure the end day.

• Month. Configure the end month.

• Hours. Configure the end hours.

• Minutes. Configure the end minutes.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual63

View the daylight saving time status

The Daylight Saving (DST) Status section shows information about the summer time settings

and whether the time shift for summer time is currently in effect.

To view the daylight saving time status:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > Time > DayLight Saving Configuration.

Offset Specify the number of minutes to shift the summer time from the standard

time. The valid range is 1–1440 minutes.

Zone Specify the acronym associated with the time zone when summer time

is in effect. This field is not validated against an official list of time zone

acronyms.

Table 16. Daylight saving setting is Non Recurring (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual64

6. To refresh the page, click the Update button.

The following table displays the nonconfigurable daylight saving status information.

Table 17. Daylight Saving (DST) Status information

Field Description

Daylight Saving (DST) The Daylight Saving value, which is one of the following:

Begins At The start date of daylight saving time. This field is not displayed when

daylight saving time is disabled.

Ends At The end date of daylight saving time. This field is not displayed when

daylight saving time is disabled.

Offset (in Minutes) The offset value in minutes.This field is not displayed when daylight

saving time is disabled.

Zone The zone acronym. This field is not displayed when daylight saving

time is disabled.

Daylight Saving (DST) in Effect Indicates whether daylight saving time is in effect.

Configure denial of service settings

You can configure the Denial of Service (DoS) settings for the switch. The switch provides

support for classifying and blocking specific types of DoS attacks.

Configure Auto-DoS

You can automatically enable all the DoS features available on the switch, except for the L4

Port attack. For information about the types of DoS attacks the switch can monitor and block,

see Configure denial of service on page 65.

To enable the Auto-DoS feature:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

• Disable

• Recurring

• Recurring EU

• Recurring USA

• Non Recurring

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual65

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > Denial of Service > Auto-DoS Configuration.

The Auto-DoS Configuration page displays.

6. Select the Auto-DoS Mode Enable radio button.

When an attack is detected, a warning message is logged to the buffered log and is sent

to the syslog server. At the same time, the port is shut down and can be enabled only

manually by the admin user.

7. Click the Apply button.

Your settings are saved.

Configure denial of service

The Denial of Service Configuration page allows you to select which types of DoS attacks the

switch monitors and blocks.

To configure individual DoS settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > Denial of Service > Denial of Service Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual66

6. Select the types of DoS attacks for the switch to monitor and block and configure any

associated values:

• Denial of Service Min TCP Header Size. Specify the minimum TCP header size

allowed. If DoS TCP Fragment is enabled, the switch drops packets with a TCP

header smaller than the configured value.

• Denial of Service ICMPv4. Enabling ICMPv4 DoS prevention causes the switch to

drop ICMPv4 packets with a type set to ECHO_REQ (ping) and a size greater than

the configured ICMPv4 packet size.

• Denial of Service Max ICMPv4 Packet Size. Specify the maximum ICMPv4 packet

size allowed. If ICMPv4 DoS prevention is enabled, the switch drops IPv4 ICMP ping

packets with a size greater than the configured value.

• Denial of Service ICMPv6. Enabling ICMPv6 DoS prevention causes the switch to

drop ICMPv6 packets with a type set to ECHO_REQ (ping) and a size greater than

the configured ICMPv6 packet size.

• Denial of Service Max ICMPv6 Packet Size. Specify the maximum IPv6 ICMP

packet size allowed. If ICMPv6 DoS prevention is enabled, the switch drops IPv6

ICMP ping packets with a size greater than the configured maximum ICMPv6 packet

size.

• Denial of Service First Fragment. Enabling First Fragment DoS prevention causes

the switch to check DoS options on first fragment IP packets when the switch receives

fragmented IP packets. Otherwise, the switch ignores the first fragment IP packages.

• Denial of Service ICMP Fragment. Enabling ICMP Fragment DoS prevention

causes the switch to drop ICMP fragmented packets.

• Denial of Service SIP=DIP. Enabling SIP=DIP DoS prevention causes the switch to

drop packets with a source IP address equal to the destination IP address.

• Denial of Service SMAC=DMAC. Enabling SMAC=DMAC DoS prevention causes

the switch to drop packets with a source MAC address equal to the destination MAC

address.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual67

• Denial of Service TCP FIN&URG&PSH. Enabling TCP FIN & URG & PSH DoS

prevention causes the switch to drop packets with TCP Flags FIN, URG, and PSH set

and TCP sequence number equal to 0.

• Denial of Service TCP Flag&Sequence. Enabling TCP Flag DoS prevention causes

the switch to drop packets with TCP control flags set to 0 and TCP sequence number

set to 0.

• Denial of Service TCP Fragment. Enabling TCP Fragment DoS prevention causes

the switch to drop packets with a TCP payload for which the IP payload length minus

the IP header size is less than the minimum allowed TCP header size.

• Denial of Service TCP Offset. Enabling TCP Offset DoS prevention causes the

switch to drop packets with a TCP header offset set to 1.

• Denial of Service TCP Port. Enabling TCP Port DoS prevention causes the switch to

drop packets for which the TCP source port is equal to the TCP destination port.

• Denial of Service TCP SYN. Enabling TCP SYN DoS prevention causes the switch

to drop packets with TCP flags SYN set.

• Denial of Service TCP SYN&FIN. Enabling TCP SYN & FIN DoS prevention causes

the switch to drop packets with TCP flags SYN and FIN set.

• Denial of Service UDP Port. Enabling UDP Port DoS prevention causes the switch

to drop packets for which the UDP source port is equal to the UDP destination port.

7. Click the Apply button.

Your settings are saved.

Configure the DNS settings

You can configure information about DNS servers that the network uses and how the switch

operates as a DNS client.

Configure the global DNS settings

You can configure global DNS settings and DNS server information.

To configure the global DNS settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual68

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > DNS > DNS Configuration.

6. Select the Disable or Enable radio button to specify whether to disable or enable the

administrative status of the DNS client.

• Enable. Allow the switch to send DNS queries to a DNS server to resolve a DNS

domain name. The DNS is enabled by default.

•Disable. Prevent the switch from sending DNS queries.

7. In the DNS Default Name field, enter the default DNS domain name to include in DNS

queries.

When the system is performing a lookup on an unqualified host name, this field is

provides the domain name (for example, if default domain name is netgear.com and the

user enters test, then test is changed to test.netgear .com to resolve the name). The name

must not be longer than 255 characters.

8. In the DNS Server field, specify the IPv4 address to which the switch sends DNS queries.

9. Click the Add button.

The server is added to the list. You can specify up to eight DNS servers. The Preference

field displays the server preference order. The preference is set in the order in which

preferences were entered.

10. To remove a DNS server from the list, select its check box and click the Delete button.

If you click the Delete button without selecting a DNS server, all the DNS servers are

deleted.

11. Click the Apply button.

Your settings are saved.

12. To refresh the page, click the Update button.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual69

The following table displays DNS Server Configuration information.

Table 18. DNS Server Configuration information

Field Description

ID The identification of the DNS Server.

Preference Shows the preference of the DNS server. The preferences are

determined by the order in which they were entered.

Configure and view host name-to-IP address information

You can manually map host names to IP addresses or view dynamic host mappings.

Add a static entry to the dynamic host mapping table

To add a static entry to the local dynamic host mapping table:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > DNS > Host Configuration.

6. In the Host Name (1 to 255 characters) field, specify the static host name to add.

Its length cannot exceed 255 characters and it is a required field.

7. In the IPv4/IPv6 Address field, enter the IP address to associate with the host name.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual70

8. Click the Add button.

The entry displays in the list on the page.

Remove an entry from the dynamic host mapping table

To remove an entry from the dynamic host mapping table:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > DNS > Host Configuration.

The DNS Host Configuration page displays.

6. Select the check box next to the entry to remove.

7. Click the Delete button.

Change the host name or IP address in an entry of the dynamic host mapping

table and view all entries

To change the host name or IP address in an entry of the dynamic host mapping table

and view all entries:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual71

The System Information page displays.

5. Select System > Management > DNS > Host Configuration.

The DNS Host Configuration page display.

6. Select the check box next to the entry to update.

7. Enter the new information in the appropriate field.

8. Click the Apply button.

Your settings are saved.

9. To clear all the dynamic host name entries from the list, click the Clear button.

The Dynamic Host Mapping table shows host name-to-IP address entries that the switch

learned. The following table describes the dynamic host fields.

Table 19. Dynamic Host Mapping information

Field Description

Host Lists the host name that you assign to the specified IP address.

Total Time since the dynamic entry was first added to the table.

Elapsed Time since the dynamic entry was last updated.

Type The type of the dynamic entry.

Addresses Lists the IP address associated with the host name.

Configure green Ethernet settings

You can configure the green Ethernet features to reduce power consumption.

Enable the green Ethernet settings

By default, the green Ethernet settings are disabled. You can enable the green Ethernet

settings.

To enable the green Ethernet settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual72

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > Green Ethernet > Green Ethernet Configuration.

6. Select the Auto Power Down Mode Disable or Enable radio button.

By default, this mode is disabled. When a port link is down, the underlying physical layer

goes down for a short period and then checks for port link pulses again so that

auto-negotiation remains possible. In this way, the switch saves power when no link

partner is present for the port.

7. Select the EEE Mode Disable or Enable radio button.

By default, this mode is disabled. Energy Efficient Ethernet (EEE) combines the MAC with

a family of physical layers that support operation in a low power mode. It is defined by the

IEEE 802.3az standard. Lower power mode enables both the send and receive sides of

the link to disable some functionality for power savings when lightly loaded. Transition to

low power mode does not change the link status. Frames in transit are not dropped or

corrupted in transition to and from low power mode. Transition time is transparent to

upper layer protocols and applications.

8. Click the Apply button.

Your settings are saved.

Configure green Ethernet interface settings

You can configure per-port Green Ethernet settings.

To configure the Green Ethernet interface settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual73

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > Green Ethernet > Green Ethernet Interface

Configuration.

6. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

7. From the EEE mode menu, select Enable or Disable.

The default is Disable. If the EEE mode is not supported, then N/A is displayed.

8. Click the Apply button.

Your settings are saved.

Configure green Ethernet local and remote devices

You can view detailed per-port green Ethernet information and enable or disable green

Ethernet settings on a single port. Using the green Ethernet features allows for power

consumption savings.

To configure green Ethernet local and remote devices:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual74

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > Green Ethernet > Green Ethernet Details.

6. From the Interface menu, select the interface.

7. From the EEE Admin mode menu, select Enable or Disable.

With the EEE mode enabled, the port transitions to low power mode during a link idle

condition. The default value is Disabled. If the EEE Admin Mode is not supported, N/A is

displayed.

8. In the EEE Transmit Idle Time field, enter the time after which switch transitions to the LPI

state.

The range is 600 to 4294967295. The default value is 600.

9. In the EEE Transmit Wake Time field, enter the time that the switch must wait before it

transitions to the active state after it receives a packet for transmission.

The range is 8 to 65535. The default value is 17.

10. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual75

11. To refresh the page, click the Update button.

12. To clear the configuration, resetting all statistics for the selected interface to default values,

click the Clear button.

The following table describes the nonconfigurable fields.

Table 20. Green Ethernet Local Device Information

Field Description

Cumulative Energy Saved on this

port due to Green mode(s) (Watts

* Hours)

Cumulative energy saved due to all green modes enabled on this port in

watts * hours.

Rx Low Power Idle Event Count This field is incremented each time MAC RX enters low-power idle (LPI)

state. Shows the total number of Rx LPI events since EEE counters were

last cleared.

Rx Low Power Idle Duration

(uSec) This field indicates duration of Rx LPI state in 10 us increments. Shows the

total duration of Rx LPI since the EEE counters were last cleared.

Tx Low Power Idle Event Count This field is incremented each time MAC TX enters LPI state. Shows the

total number of Tx LPI events since EEE counters were last cleared.

Tx Low Power Idle Duration

(uSec) This field indicates duration of Tx LPI state in 10 us increments. Shows the

total duration of Tx LPI since the EEE counters were last cleared.

Tw_sys_tx (uSec) Integer that indicates the value of Tw_sys that the local system can

support.

Tw_sys_tx Echo (uSec) Integer that indicates the remote system’s Transmit Tw_sys that was used

by the local system to compute the Tw_sys that it wants to request from the

remote system.

Tw_sys_rx (uSec) Integer that indicates the value of Tw_sys that the local system requests

from the remote system.

Tw_sys_rx Echo (uSec) Integer that indicates the remote system’s Receive Tw_sys that was used

by the local system to compute the Tw_sys that it can support.

Fallback Tw_sys (uSec) Integer that indicates the value of fallback Tw_sys that the local system

requests from the remote system.

Tx_dll_enabled Data Link Layer Enabled: Initialization status of the EEE transmit Data Link

Layer management function on the local system.

Tx_dll_ready Data Link Layer ready: This variable indicates that the tx system

initialization is complete and is ready to update/receive LLDPDU containing

EEE TLV.

Rx_dll_enabled Status of the EEE capability negotiation on the local system.

Rx_dll_ready Data Link Layer ready: This variable indicates that the rx system

initialization is complete and is ready to update/receive LLDPDU containing

EEE TLV.

Time Since Counters Last Cleared Time Since Counters Last Cleared (since the time of power-up, or after

EEE counters are cleared).

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual76

View green Ethernet remote device details

To view green Ethernet remote device information:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > Green Ethernet >Green Ethernet Details.

The Green Ethernet Details page displays.

6. Scroll down to the Remote Device Information section.

7. Select the interface.

The following table describes the nonconfigurable fields.

Table 21. Green Ethernet Remote Device Information

Field Description

Remote ID The remote client identifier assigned to the remote system.

Remote Tw_sys_tx (uSec) Integer that indicates the value of Tw_sys that the remote system can

support.

Remote Tw_sys_tx Echo (uSec) Integer that indicates the value of Transmit T w_sys echoed back by the

remote system.

Remote Tw_sys_rx (uSec) Integer that indicates the value of Tw_sys that the remote system

requests from the local system.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual77

View the green Ethernet statistics summary

This page summarizes the green Ethernet settings currently in use.

To view the green Ethernet statistics:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > Green Ethernet > Green Ethernet Summary.

Remote Tw_sys_rx Echo (uSec) Integer that indicates the value of Receive Tw_sys echoed back by the

remote system.

Remote Fallback Tw_sys (uSec) Integer that indicates the value of fallback Tw_sys that the remote

system is advertising.

Table 21. Green Ethernet Remote Device Information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual78

6. To refresh the page, click the Update button.

The following table describes the nonconfigurable fields.

Table 22. Green Ethernet Statistics Summary information

Field Description

Current Power Consumption (mW) Estimated power consumption by all ports of the switch in mWatts.

Percentage Power Saving (%) Estimated percentage of power saved on all ports of the switch if the green

modes are enabled.

Cumulative Energy Saving (W * H) Estimated cumulative energy saved on the switch in watts multiplied by

hours if all green modes are enabled.

Unit The unit ID.

Green Features supported on this

unit List of green features supported on the given unit, which could be one or

more of the following: Energy-Detect (Energy Detect), Short-Reach (Short

Reach), EEE (Energy Efficient Ethernet), LPI-History (EEE Low Power Idle

History), LLDP-Cap-Exchg (EEE LLDP Capability Exchange), Pwr-Usg-Est

(Power Usage Estimates).

Interface Interface for which data is displayed or configured.

Energy Detect Admin mode Enable or disable Energy Detect mode on the port. When this mode is

enabled, when the port link is down, the PHY automatically goes down for a

short period of time, then wakes up to check link pulses. This allows the

switch to perform autonegotiation and save power consumption when no

link partner is present.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual79

Configure the green Ethernet EEE LPI history

You can configure and view the Green Ethernet low power idle (LPI) history.

To configure the port Green Ethernet EEE LPI history:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Management > Green Ethernet > Green Ethernet LPI History.

6. Select the interface.

7. In the Sampling Interval field, enter the interval at which EEE LPI data is collected.

This is a global setting and is applied to all interfaces. The range is 30 to 36000.The

default value is 3600.

Energy Detect Operational Status Current operational status of the Energy Detect mode.

EEE Admin mode Enable or disable Energy Efficient Ethernet mode on the port. With EEE

mode enabled, the port transitions to low power mode during link idle

conditions.

Table 22. Green Ethernet Statistics Summary information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual80

8. In the Max Samples to keep field, enter the maximum number of samples to keep.

This is a global setting and is applied to all interfaces. The range is 1 to 168.The default

value is 168.

9. Click the Apply button.

Your settings are saved.

The Percentage LPI time field shows the time spent in LPI mode the since EEE counters

were last cleared.

The following table describes the nonconfigurable fields.

Table 23. Interface Green Mode EEE LPI History information

Field Description

Sample No. Sample index.

Time Since The Sample Was

Recorded Each time the page is refreshed, it shows a different time as it reflects the

difference between current time and time at which the sample was

recorded.

Percentage Time spent in LPI

mode since last sample Percentage of time spent in LPI mode during the current measurement

interval.

Percentage Time spent in LPI

mode since last reset Percentage of time spent in LPI mode since EEE LPI statistics were reset.

Use the Device View

For information about the device view, see Change the language of the local browser

interface on page 24.

Configure Power over Ethernet

You can configure the global Power over Ethernet (PoE) configuration settings and the PoE

settings for each port.

Configure the global PoE settings

To configure the PoE settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual81

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > PoE > Basic > PoE Configuration.

6. In the System Usage Threshold field, enter a number from 1 to 99 to set the threshold

level at which a trap is sent if the consumed power exceeds the threshold power.

7. From the Power Management mode menu, select the power management algorithm that

the switch uses to deliver power to the requesting powered devices (PDs):

• Static. Specifies that the power allocated for each port depends on the type of power

threshold configured on the port.

• Dynamic. Specifies that the power consumption on each port is measured and

calculated in real time.

8. To active the PoE traps, from the Traps menu, select Enable.

Selecting Disable deactivates the PoE traps. The default setting is Enabled.

9. Click the Apply button.

Your settings are saved.

The following table describes the nonconfigurable fields on the page.

Table 24. PoE Configuration fields

Field Description

Firmware Version The firmware version of the PoE firmware component.

Power Status The power status.

Total Power Available Watts The maximum amount of power in watts that the switch can deliver to all ports.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual82

Configure the PoE port settings

To configure the PoE port settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > PoE > Advanced > PoE Port Configuration.

The previous figure shows only part of the PoE Port Configuration page.

6. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

Threshold Power Watts If the consumed power is below the threshold power, the switch can power up

another port. The consumed power can be between the nominal and threshold

power. The threshold power is displayed in watts.

Note: The threshold power value is determined by the value that you enter in the

System Usage Threshold field.

Consumed Power Watts The total amount of power in watts that is being delivered to all ports.

Table 24. PoE Configuration fields (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual83

7. From the Port Power menu, select the administrative PoE mode of the port:

• Enable. The port’s capacity to deliver power is enabled. This is the default setting.

• Disable. The port’s capacity to deliver power is disabled.

8. From the Port Priority menu, select the priority for the port in relation to other ports if the

total power that the switch is capable of delivering exceeds the total power budget:

• Low. Low priority. This is the default setting.

• Medium. Medium priority.

•High. High priority.

•Critical. Critical priority.

The port priority determines which ports can still deliver power after the total power

delivered by the switch exceeds the total power budget. (In such a situation, the switch

might not be able to deliver power to all connected devices.) If the same priority applies to

two ports, the lower-numbered port receives higher priority.

9. From the Power Mode menu, select the PoE mode that the port must function in:

• 802.3af. The port is powered in and limited to the IEEE 802.3af mode. A PD that

requires IEEE 802.3at does not receive power if the port functions in IEEE 802.3af

mode.

• Legacy. The port is powered using high-inrush current, which is used by legacy PDs

that require more than 15W to power up.

•Pre-802.3at. The port is initially powered in the IEEE 802.3af mode and, before

75 msec pass, is switched to the high power IEEE 802.3at mode. Select this mode if

the PD does not perform Layer 2 classification or if the switch performs

2-event Layer 1 classification.

•802.3at. The port is powered in the IEEE 802.3at mode and is backward compatible

with IEEE 802.3af. The 802.3at mode is the default mode. In this mode, if the switch

detects that the attached PD requests more power than IEEE 802.3af but is not an

IEEE 802.3at Class 4 device, the PD does not receive power from the switch.

10. From the Power Limit Type menu, select how the port controls the maximum power that it

can deliver:

•None. The port draws up to Class 0 maximum power in low power mode and up to

Class 4 maximum power in high power mode.

•Class. The port power limit is equal to the class of the attached PD.

•User. The port power limit is equal to the value that is specified in the Power Limit

(mW) field. This is the default setting.

Note: If a PD does not report its class correctly, use of these options can

preserve additional PoE power by preventing the switch from

delivering more power than the PD requires. However, depending on

which option you select, a PD that does not report its class correctly

might not power up at all.

11. In the Power Limit (mW) field, enter the maximum power (in mW) that the port can deliver.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual84

The range is 3,000–30,000 mW. The default is 30,000 mW.

12. From the Detection Type menu, select how the port detects the attached PD:

•IEEE 802. The port performs a 4-point resistive detection. This is the default setting.

• 4pt 802.3af + Legacy. The port performs a 4-point resistive detection, and if required,

continues with legacy detection.

•Legacy. The port performs legacy detection.

13. From the Timer Schedule menu, select a timer schedule or select None, which is the

default selection.

For information about setting up and configuring PoE timer schedules, see Set up PoE

timer schedules on page 123.

14. Click the Apply button.

Your settings are saved.

The following table describes the nonconfigurable fields on the page.

Table 25. PoE Port Configuration

Field Description

High Power All ports supports high power mode.

Max Power (mW) The maximum power in milliwatts that can be provided by the port.

Class The class defines the range of power that a powered device (PD) is drawing from

the switch. The class definitions are as follows:

• 0: 0.44–16.2W

• 1: 0.44–4.2W

• 2: 0.44–7.4W

• 3: 0.44–16.2W

• 4: 0.44–31.6W

• Unknown. The class cannot be detected, or no PD is attached to the port.

Output Voltage (Volts) The voltage that is delivered to the PD in volts.

Output Current (mA) The current that is delivered to the PD in mA.

Output Power (W) The power that is delivered to the PD in watts.

Status The operational status of the port. The possible values are as follows:

• Disabled. No power is delivered.

• Delivering

Power. Power is being drawn by the PD.

• Requesting

Power. The port is requesting power.

• Fault. A problem occurred with the power.

• Test. The port is in test mode.

• Other Fault. The port is idle because of an error condition.

• Searching. The port is not in one of the other states in this list.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual85

Configure SNMP

You can configure SNMP settings for SNMPv1/v2 and SNMPv3. The switch software

supports the configuration of SNMP groups and users that can manage traps that the SNMP

agent generates.

The switch uses both standard public MIBs for standard functionality and private MIBs that

support additional switch functionality. All private MIBs begin with a hyphen (-) prefix. The

main object for interface configuration is in -SWITCHING-MIB, which is a private MIB. Some

interface configurations also involve objects in the public MIB, IF-MIB.

Configure the SNMPv1 or SNMPv2 community

Only the communities that you define can access to the switch using the SNMP V1 and

SNMP V2 protocols. Only those communities with read/write level access can be used to

change the configuration using SNMP.

Add an SNMP community:

To add an SNMP community:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

Fault Status The error description when the PoE port is in a fault state. The possible values are

as follows:

• No Error. The port is not in any error state and can provide power.

• MPS Absent. The port detected the absence of the main power supply,

preventing the port from providing power.

• Short. The port detected a short circuit condition, preventing the port from

providing power.

• Overload. The PD that is connected to the port attempts to draw more power

than allowed by the port’s settings, preventing the port from providing power at

all.

• Power Denied. The port was denied power because of a shortage of power or

because of an administrative condition. In this condition, the port cannot

provide power.

Table 25. PoE Port Configuration (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual86

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > SNMP > SNMP V1/V2 > Community Configuration.

6. In the Management Station IP field, specify the IP address of the management station.

7. In the Management Station IP Mask field, specify the subnet mask to associate with the

management station IP address.

Together, the management station IP and the management station IP mask denote a

range of IP addresses from which SNMP clients can use that community to access this

device. If either the management station IP or management station IP mask value is

0.0.0.0, access is allowed from any IP address. Otherwise, every client’s address is

ANDed with the mask, as is the management station IP address. If the values are equal,

access is allowed. For example, if the management station IP and management station

IP mask settings are 192.168.1.0/255.255.255.0, then any client whose address is

192.168.1.0 through 192.168.1.255 (inclusive) is allowed access. To allow access from

only one station, use a management station IP mask value of 255.255.255.255, and use

that machine’s IP address for client address.

8. In the Community String field, specify a community name.

9. From the Access Mode menu, select the access level for this community, which is either

Read/Write or Read Only.

10. From the Status menu, select to enable or disable the community.

If you select Enable, the community name must be unique among all valid community

names or the set requests are rejected. If you select Disable, the community name

becomes invalid.

11. Click the Add button.

The selected community is added.

Modify an existing SNMP community

To modify an existing SNMP community:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual87

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > SNMP > SNMP V1/V2 > Community Configuration.

The Community Configuration page displays.

6. Select the check box next to the community.

7. Update the desired fields.

8. Click the Apply button.

Your settings are saved.

Delete an SNMP community

To delete an SNMP community:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > SNMP > SNMP V1/V2 > Community Configuration.

The Community Configuration page displays.

6. Select the check box next to the community to remove.

7. Click the Delete button.

The community is removed.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual88

Configure SNMPv1 and SNMPv2 trap settings

You can configure settings for each SNMPv1 or SNMPv2 management host that must

receive notifications about traps generated by the device. The SNMP management host is

also known as the SNMP trap receiver.

Add an SNMP trap receiver

To add an SNMP trap receiver:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > SNMP > SNMP V1/V2 > Trap Configuration.

6. In the Recipients IP field, enter the IPv4 address in the x.x.x.x format to receive SNMP

traps from this device.

7. From the Version menu, select the trap version to be used by the SNMP trap receiver.

•SNMP V1. The switch uses SNMPv1 to send traps to the receiver. The default setting

is SNMP V1.

• SNMP V2. The switch uses SNMPv2 to send traps to the receiver.

8. In the Community String field, specify the name of the SNMP community that includes

the SNMP management host and the SNMP agent on the device.

This name can be up to 16 characters and is case-sensitive.

9. From the Status menu, select Enable to send traps to the receiver or select Disable to

prevent the switch from sending traps to the receiver.

10. Click the Add button.

The receiver configuration is added.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual89

Modify information about an existing SNMP recipient

To modify information about an existing SNMP recipient:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > SNMP > SNMP V1/V2 > Trap Configuration .

The Trap Configuration page displays.

6. Select the check box next to the recipient.

7. Update the desired fields.

8. Click the Apply button.

Your settings are saved.

Delete an SNMP recipient

To delete an SNMP trap recipient:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > SNMP > SNMP V1/V2 > Trap Configuration .

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual90

The Trap Configuration page displays.

6. Select the check box next to the recipient to remove.

7. Click the Delete button.

The trap recipient is removed.

Configure SNMPv1 and SNMPv2 trap flags

You can enable or disable traps that the switch can send to an SNMP manager. When the

condition identified by an active trap is encountered by the switch, a trap message is sent to

any enabled SNMP trap receivers, and a message is written to the trap log.

To configure the trap flags:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > SNMP > SNMP V1/V2 > Trap Flags .

6. Enable or disable the following system traps:

• Authentication. When enabled, SNMP traps are sent when events involving

authentication occur, such as when a user attempts to access the local browser

interface and does not provide a valid user name and password. The default is

Enable.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual91

• Link Up/Down. When enabled, SNMP traps are sent when the administrative or

operational state of a physical or logical link changes. The default is Enable.

• Spanning Tree. When enabled, SNMP traps are sent when various spanning tree

events occur. The default is Enable.

•ACL. When enabled, SNMP traps are sent when a packet matches a configured ACL

rule that includes ACL logging. The default is Disable.

7. Click the Apply button.

Your settings are saved.

View the supported MIBs

You can display the MIBs that are supported by the switch.

To view the supported MIBs:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > SNMP > SNMP V1/V2 > Supported MIBs.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual92

The following table describes the SNMP Supported MIBs Status fields.

Table 26. SNMP supported MIBs

Field Description

Name The RFC number if applicable and the name of the MIB.

Description The RFC title or MIB description.

Configure SNMPv3 users

Any user can connect to the switch using the SNMPv3 protocol, but for authentication and

encryption, the switch supports only one user (admin). Therefore, you can create or modify

only one profile.

To configure authentication and encryption settings for the SNMPv3 admin profile by

using the local browser interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > SNMP > SNMPv3 > User Configuration.

The User Configuration page displays.

The SNMPv3 Access Mode field is a read-only field that shows the access privileges for

the user account. Access for the admin account is always Read/Write. Access for all

other accounts is Read Only.

6. To enable authentication, select an Authentication Protocol radio button.

You can select the MD5 radio button or the SHA radio button. With either of these

options, the user login password is used as SNMPv3 authentication password. For

information about how to configure the login password, see Change the device

password for the local browser interface on page 289.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual93

7. To enable encryption:

a. Select the Encryption Protocol DES radio button to encrypt SNMPv3 packets using

the DES encryption protocol.

b. In the Encryption Key field, enter an encryption code of eight or more alphanumeric

characters.

8. Click the Apply button.

Your settings are saved.

Configure LLDP

The IEEE 802.1AB-defined standard, Link Layer Discovery Protocol (LLDP), allows stations

on an 802 LAN to advertise major capabilities and physical descriptions. This information is

viewed by a network manager to identify system topology and detect bad configurations on

the LAN.

LLDP is a one-way protocol without any request/response sequences. Information is

advertised by stations implementing the transmit function, and is received and processed by

stations implementing the receive function. The transmit and receive functions can be

enabled or disabled separately per port. By default, both transmit and receive are disabled on

all ports. The application is responsible for starting each transmit and receive state machine

appropriately, based on the configured status and operational state of the port.

The Link Layer Discovery Protocol-Media Endpoint Discovery (LLDP-MED) is an

enhancement to LLDP with the following features:

•Autodiscovery of LAN policies (such as VLAN, Layer 2 priority, and DiffServ settings),

enabling plug and play networking.

•Device location discovery for creation of location databases.

•Extended and automated power management of Power over Ethernet endpoints.

•Inventory management, enabling network administrators to track their network devices

and determine their characteristics (manufacturer, software and hardware versions,

serial/asset number).

Configure the LLDP global settings

You can specify the global LLDP and LLDP-MED settings that are applied to the switch.

To configure the global LLDP settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual94

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > LLDP > Basic > LLDP Configuration.

6. To configure nondefault values for the following LLDP properties, specify the following

options:

• TLV Advertised Interval. The number of seconds between transmissions of LLDP

advertisements.

• Hold Multiplier . The transmit interval multiplier value, where transmit hold multiplier ×

transmit interval = the time to live (TTL) value that the device advertises to neighbors.

• Re-initializing Delay. The number of seconds to wait before attempting to re-initialize

LLDP on a port after the LLDP operating mode on the port changes.

• Transmit Delay. The minimum number of seconds to wait between transmissions of

remote data change notifications to one or more SNMP trap receivers configured on

the switch.

7. To configure a nondefault value for LLDP-MED, enter a value in the Fast Start Duration

field.

This value sets the number of LLDP packets sent when the LLDP-MED fast start

mechanism is initialized, which occurs when a new endpoint device links with the

LLDP-MED network connectivity device.

8. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual95

Configure the LLDP port settings

You can specify per-interface LLDP settings.

To configure the LLDP interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > LLDP > Advanced > LLDP Port Settings.

6. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

7. Use the following menus to configure the LLDP settings for the selected ports:

•Admin Status. Select the status for transmitting and receiving LLDP packets:

- Tx Only. Enable only transmitting LLDP PDUs on the selected ports.

- Rx Only. Enable only receiving LLDP PDUs on the selected ports.

- Tx and Rx. Enable both transmitting and receiving LLDP PDUs on the selected

ports.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual96

- Disabled. Do not transmit or receive LLDP PDUs on the selected ports.

The default is Tx and Rx.

• Management IP Address. Choose whether to advertise the management IP address

from the interface. The possible field values are as follows:

-Stop Advertise. Do not advertise the management IP address from the interface.

- Auto Advertise. Advertise the current IP address of the device as the

management IP address.

The default is Auto Advertise.

• Notification. When notifications are enabled, LLDP interacts with the trap manager to

notify subscribers of remote data change statistics. The default is Disable.

•Optional TLV(s). Enable or disable the transmission of optional type-length value

(TLV) information from the interface. The default is Enable. The TLV information

includes the system name, system description, system capabilities, and port

description.

For information about how to configure the system name, see View or define system

information on page 35. For information about how to configure the port description,

see Configure the port settings on page 131.

8. Click the Apply button.

Your settings are saved.

View the LLDP-MED network policy

You can view information about the LLPD-MED network policy TLV that is transmitted in the

LLDP frames on a local interface.

To view LLDP-MED network policy information for an interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > LLDP > Advanced > LLDP-MED Network Policy.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual97

The LLDP-MED Network Policy page displays.

6. From the Interface menu, select the interface for which you want to view the information.

Note: The menu includes only the interfaces on which LLDP is enabled. If no

interfaces are enabled for LLDP, the Interface menu does not display.

The page refreshes and displays the data transmitted in the network policy TLVs for the

interface.

The following table describes the LLDP-MED network policy information that displays on the

page.

Table 27. LLDP-MED network policy information

Field Description

Network Policy Number The policy number.

Application The media application type associated with the policy, which can be one of the

following:

A port can receive multiple application types. The application information is

displayed only if a network policy TLV was transmitted from the port.

VLAN ID The VLAN ID associated with the policy.

VLAN Type Indicates whether the VLAN associated with the policy is tagged or untagged.

User Priority The priority associated with the policy.

DSCP The DSCP associated with a particular policy type.

Configure the LLDP-MED port settings

You can enable LLDP-MED mode on an interface and configure its properties.

To configure LLDP-MED settings for a port:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

• Unknown

• Voice

• Guest Voice

• Guest Voice Signaling

• Softphone Voice

• Video Conferencing

• Streaming Video

• Video Signaling

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual98

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > LLDP > Advanced > LLDP-MED Port Settings.

The LLDP-MED Port Settings page displays.

6. From the Port menu, select the port to configure.

7. Use the following menus to enable or disable the following LLDP-MED settings for the

selected port:

• LLDP-MED Status. The administrative status of LLDP-MED on the interface. When

LLDP-MED is enabled, the transmit and receive function of LLDP is effectively

enabled on the interface.

• Notification. When Notification is enabled, the port sends a topology change

notification if a device is connected or removed.

• MED Capabilities. When MED Capabilities is enabled, the port transmits the

capabilities type length values (TLVs) in the LLDP PDU frames.

•Network Policy. When Network Policy is enabled, the port transmits the network

policy TLV in LLDP frames.

• Extended MDI-PSE. When Extended MDI-PSE is enabled, the port transmits the

extended PSE TLV in LLDP frames.

8. Click the Apply button.

Your settings are saved.

View the local LLDP information

You can view the data that each port advertises through LLDP.

To view local LLDP information:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual99

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Advanced > LLDP > Local Information.

The page includes only the interfaces on which LLDP is enabled.

The following table describes the LLDP device information and port summary

information.

Field Description

Chassis ID Subtype The type of information used to identify the switch in the Chassis ID field.

Chassis ID The hardware platform identifier for the switch.

System Name The user-configured system name for the switch.

System Description The switch description, which includes information about the product model

and platform.

System Capabilities The primary functions that the switch supports.

Interface The interface associated with the rest of the data in the row.

Port ID Subtype The type of information used to identify the interface in the Port ID field.

Port ID The port number.

Port Description The user-defined description of the port. For information about how to

configure the port description, see Configure the port settings on page 131.

Advertisement The TLV advertisement status of the port.

6. To view additional details about a port, click the name of the port in the Interface column of

the Port Information table.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual100

The following table describes the detailed local information that displays for the selected

port.

Field Description

Managed Address

Address SubType The type of address the local browser interface uses, such as an IPv4

address.

Address The address used to manage the device.

Interface SubType The port subtype.

Interface Number The number that identifies the port.

MAC/PHY Details

Auto Negotiation Supported Indicates whether the interface supports port speed autonegotiation. The

possible values are True and False.

Auto Negotiation Enabled The port speed autonegotiation support status. The possible values are True

(enabled) or False (disabled).

Auto Negotiation Advertised

Capabilities The port speed autonegotiation capabilities such as 1000BASE-T half-duplex

mode or 100BASE-TX full-duplex mode.

Operational MAU Type The Medium Attachment Unit (MAU) type. The MAU performs physical layer

functions, including digital data conversion from the Ethernet interface

collision detection and bit injection into the network.

MED Details

Capabilities Supported The MED capabilities enabled on the port.

Current Capabilities The TLVs advertised by the port.

Device Class Network Connectivity indicates that the device is a network connectivity

device.

Network Policies

Application Type The media application type associated with the policy.

VLAN ID The VLAN ID associated with the policy.

VLAN Type Specifies whether the VLAN associated with the policy is tagged or untagged.

User Priority The priority associated with the policy.

DSCP The DSCP associated with a particular policy type.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual101

View the LLDP-MED neighbor device information

You can view the data that a specified interface received from other LLDP-enabled systems.

To view LLDP information received from a neighbor device:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Advanced > LLDP > Neighbor Information.

If no information was received from a neighbor device, or if the link partner is not

LLDP-enabled, no information displays.

The following table describes the information that displays for all LLDP neighbors that

were discovered.

Field Description

MSAP Entry The Media Service Access Point (MSAP) entry number for the remote

device.

Local Port The interface on the local system that received LLDP information from a

remote system.

Chassis ID Subtype The type of data displayed in the Chassis ID field on the remote system.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual102

6. To view additional information about the remote device, click the link in the MSAP Entry

column.

A pop-up window displays information for the selected port.

The following table describes the information transmitted by the neighbor.

Chassis ID The remote 802 LAN device’s chassis.

Port ID Subtype The type of data displayed in the remote system’s Port ID field.

Port ID The physical address of the port on the remote system from which the data

was sent.

System Name The system name associated with the remote device. If the field is blank, the

name might not be configured on the remote system.

Field Description

Port Details

Local Port The interface on the local system that received LLDP information from a

remote system.

MSAP Entry The Media Service Access Point (MSAP) entry number for the remote device.

Basic Details

Chassis ID Subtype The type of data displayed in the Chassis ID field on the remote system.

Chassis ID The remote 802 LAN device’s chassis.

Port ID Subtype The type of data displayed in the remote system’s Port ID field.

Port ID The physical address of the port on the remote system from which the data

was sent.

Port Description The user-defined description of the port.

System Name The system name associated with the remote device.

System Description The description of the selected port associated with the remote system.

System Capabilities The system capabilities of the remote system.

Managed Addresses

Address SubType The type of the management address.

Address The advertised management address of the remote system.

Interface SubType The port subtype.

Interface Number The port on the remote device that sent the information.

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual103

MAC/PHY Details

Auto-Negotiation Supported Specifies whether the remote device supports port-speed autonegotiation.

The possible values are True or False.

Auto-Negotiation Enabled The port speed autonegotiation support status. The possible values are True

and False.

Auto Negotiation Advertised

Capabilities The port speed autonegotiation capabilities.

Operational MAU Type The Medium Attachment Unit (MAU) type. The MAU performs physical layer

functions, including digital data conversion from the Ethernet interface

collision detection and bit injection into the network.

MED Details

Capabilities Supported The supported capabilities that were received in MED TLV from the device.

Current Capabilities The advertised capabilities that were received in MED TLV from the device.

Device Class The LLDP-MED endpoint device class. The possible device classes are as

follows:

• Endpoint Class 1 Indicates a generic endpoint class, offering basic LLDP

services.

• Endpoint Class 2 Indicates a media endpoint class, offering media

streaming capabilities as well as all Class 1 features.

• Endpoint Class 3 Indicates a communications device class, offering all

Class 1 and Class 2 features plus location, 911, Layer 2 switch support,

and device information management capabilities.

Hardware Revision The hardware version advertised by the remote device.

Firmware Revision The firmware version advertised by the remote device.

Software Revision The software version advertised by the remote device.

Serial Number The serial number advertised by the remote device.

Model Name The model name advertised by the remote device.

Asset ID The asset ID advertised by the remote device.

Location Information

Civic The physical location, such as the street address, that the remote device

advertised in the location TLV, for example, 123 45th St. E. The field value

length range is 6–160 characters.

Coordinates The location map coordinates that the remote device advertised in the

location TLV, including latitude, longitude, and altitude.

ECS ELIN The Emergency Call Service (ECS) Emergency Location Identification

Number (ELIN) that the remote device advertised in the location TLV. The

field range is 10–25.

Unknown The unknown location information for the remote device.

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual104

Configure a DHCP L2 relay, DHCP

snooping, and dynamic ARP inspection

The switch supports a DHCP L2 relay, DHCP snooping, and Dynamic ARP Inspection (DAI).

DHCP snooping and DAI are Layer 2 security features that examine traffic to help prevent

accidental and malicious attacks on the switch or network.

Configure a DHCP L2 relay

DHCP relay agents eliminate the need to connect to a DHCP server on each physical

network. Relay agents populate the giaddr field and also append the Relay Agent Information

option to the DHCP messages. DHCP servers use this option for IP addresses and

assignment policies for other settings. These DHCP relay agents are typically IP

routing-aware devices and are referred to as Layer 3 relay agents. In some network

configurations, a need might exist for Layer 2 devices to append the Relay Agent Information

option as they are closer to the end hosts.

These Layer 2 devices typically operate only as bridges for the network and might not include

an IPv4 address on the network. Lacking a valid IPv4 source address, they cannot relay

packets directly to a DHCP server located on another network. These Layer 2 devices

append the Relay Agent Information option and broadcast the DHCP message.

Network Policies

Application Type The media application type associated with the policy advertised by the

remote device.

VLAN ID The VLAN ID associated with the policy.

VLAN Type Specifies whether the VLAN associated with the policy is tagged or untagged.

User Priority The priority associated with the policy.

DSCP The DSCP associated with a particular policy type.

LLDP Unknown TLVs

Type The unknown TLV type field.

Value The unknown TLV value field.

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual105

Enable the DHCP L2 relay mode

You can enable the DHCP L2 relay mode.

To enable the DHCP L2 relay mode:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System> Services > DHCP L2 Relay > DHCP L2 Relay Global Configuration.

6. Select the Enable radio button

The default admin mode is disabled.

7. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual106

Configure DHCP L2 relay interface settings

You can view and configure the DHCP L2 relay interface.

To configure DHCP L2 relay interface settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System> Services > DHCP L2 Relay > DHCP L2 Relay Interface Configuration.

6. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

7. From the Admin Mode menu, select to enable or disable the DHCP L2 relay on the

selected interface.

The default is Disable.

8. From the 82 Option Trust Mode menu, select to enable or disable an interface to be trusted

for DHCP L2 Relay (Option-82) received.

The default is Disable.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual107

9. Click the Apply button.

Your settings are saved.

View the DHCP L2 relay interface statistics

You can view information about the DHCP L2 relay interface.

To view DHCP L2 relay interface statistics:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System> Services > DHCP L2 Relay > DHCP L2 Relay Interface Statistics.

The following table describes the nonconfigurable data that is displayed.

Field Description

Interface The interface from which the DHCP message is received.

Untrusted Server

Messages With Opt82 The number of DHCP message with option82 received from an untrusted server.

Untrusted Client

Messages With Opt82 The number of DHCP message with option82 received from an untrusted client.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual108

6. Click the Update button to refresh the page with the latest information about the switch.

7. Click the Clear button to reset the statistics.

Configure DHCP snooping

DHCP snooping is a useful feature that provides security by filtering untrusted DHCP

messages and by building and maintaining a DHCP snooping binding table. An untrusted

message is a message that is received from outside the network or firewall and that can

cause traffic attacks within your network. The DHCP snooping binding table contains the

MAC address, IP address, lease time, binding type, VLAN number, and interface information

that corresponds to the local untrusted interfaces of a switch. An untrusted interface is an

interface that is configured to receive messages from outside the network or firewall. A

trusted interface is an interface that is configured to receive only messages from within the

network.

DHCP snooping acts like a firewall between untrusted hosts and DHCP servers. It also

provides way to differentiate between untrusted interfaces connected to the end user and

trusted interfaces connected to the DHCP server or another switch.

Configure the global DHCP snooping settings

You can view and configure the global settings for DHCP snooping.

To configure the global DHCP snooping settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System> Services > DHCP Snooping > Global Configuration.

T rusted Server Messages

Without Opt82 The number of DHCP message without option82 received from a trusted server.

Trusted Client Messages

Without Opt82 The number of DHCP message without option82 received from a trusted client.

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual109

6. Select the DHCP Snooping Mode Enable radio button.

7. To enable the verification of the sender’s MAC address for DHCP snooping, select the MAC

Address Validation Enable radio button.

When MAC address validation is enabled, the device checks packets that are received

on an untrusted interface to verify that the MAC address and the DHCP client hardware

address match. If the addresses do not match, the device drops the packet.

8. Click the Apply button.

Your settings are saved.

Enable DHCP for all interfaces in a VLAN

To enable DHCP snooping for all interfaces that are members of a VLAN:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System> Services > DHCP Snooping > Global Configuration.

The DHCP Snooping Global Configuration page displays.

6. In the VLAN ID field, specify the VLAN on which DHCP snooping is enabled.

7. From the DHCP Snooping Mode menu, select Enable.

8. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual110

Configure DHCP snooping interface settings

You can view and configure each port as a trusted or untrusted port. Any DHCP responses

received on a trusted port are forwarded. If a port is configured as untrusted, any DHCP (or

BootP) responses received on that port are discarded.

To configure DHCP snooping interface settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System> Services > DHCP Snooping > Interface Configuration.

6. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

7. From the Trust Mode menu, select the desired trust mode:

•Disabled. The interface is considered to be untrusted and could potentially be used to

launch a network attack. DHCP server messages are checked against the bindings

database. On untrusted ports, DHCP snooping enforces the following security rules:

-DHCP packets from a DHCP server (DHCPOFFER, DHCPACK, DHCPNAK,

DHCPRELEASEQUERY) are dropped.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual111

-DHCPRELEASE and DHCPDECLINE messages are dropped if the MAC address

is in the snooping database but the binding’s interface is other than the interface

where the message was received.

-DHCP packets are dropped when the source MAC address does not match the

client hardware address if MAC address validation is globally enabled.

• Enabled. The interface is considered to be trusted and forwards DHCP server

messages without validation.

8. From the Logging Invalid Packets menu, select the packet logging mode.

When enabled, the DHCP snooping feature generates a log message when an invalid

packet is received and dropped by the interface.

9. In the Rate Limit (pps) field, specify the rate limit value for DHCP snooping purposes.

If the incoming rate of DHCP packets per second exceeds the configured burst interval

per second, the port shuts down. If the rate limit value is N/A, then the burst interval is

also nonapplicable, and rate limiting is disabled.

10. In the Burst Interval (secs) field, specify the burst interval value for rate limiting purposes

on this interface.

If the rate limit is N/A, then the burst interval is also nonapplicable, and the field displays

N/A.

11. Click the Apply button.

Your settings are saved.

Configure static DHCP bindings

You can view , add, and remove static bindings in the DHCP snooping bindings database and

to view or clear the dynamic bindings in the bindings table.

To configure static DHCP bindings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System> Services > DHCP Snooping > Binding Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual112

6. From the Interface menu, select the interface on which the DHCP client is authorized.

7. In the MAC Address field, specify the MAC address for the binding to be added.

This is the key to the binding database.

8. From the VLAN ID menu, select the ID of the VLAN the client is authorized to use.

9. In the IP Address field, specify the IP address of the client.

10. Click the Add button.

The DHCP snooping binding entry is added to the database.

The Dynamic Binding Configuration table shows information about the DHCP bindings that

were learned on each interface on which DHCP snooping is enabled. The following table

describes the dynamic bindings information.

Table 28. DHCP Dynamic Configuration information

Field Description

Interface The interface on which the DHCP client message was received.

MAC Address The MAC address associated with the DHCP client that sent the message. This is the

key to the binding database.

VLAN ID The VLAN ID of the client interface.

IP Address The IP address assigned to the client by the DHCP server.

Lease T ime The remaining IP address lease time for the client.

Configure persistent settings for DHCP snooping

You can configure the persistent location of the DHCP snooping bindings database. The

bindings database can be stored locally on the device or on a remote system somewhere

else in the network. The device must be able to reach the IP address of the remote system to

send bindings to a remote database.

To configure persistent settings for DHCP snooping:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual113

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System> Services > DHCP Snooping > Persistent Configuration.

6. Specify where the DHCP snooping bindings database is located.

• Local. The binding table is stored locally on the switch.

• Remote. The binding table is stored on a remote TFTP server.

If the database is stored on a remote server, specify the following information:

a. Specify the IP address of the TFTP server.

b. Specify the file name of the DHCP snooping bindings database in which the

bindings are stored.

7. In the Write Delay field, specify the time to wait between writing bindings information to

persistent storage.

The delay allows the device to collect as many entries as possible (new and removed)

before writing them to the persistent file.

8. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual114

View and clear the DHCP snooping statistics

You can view and clear per-interface statistics about the DHCP messages filtered by the

DHCP snooping feature on untrusted interfaces.

To view and clear the DHCP snooping statistics:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System> Services > DHCP Snooping > Statistics.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Click the Clear button to clear all interfaces statistics.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual115

The following table describes the DHCP snooping statistics.

Table 29. DHCP Snooping Statistics information

Field Description

Interface The interface associated with the rest of the data in the row.

MAC Verify Failures The number of DHCP messages that were dropped because the source MAC address

and client hardware address did not match. MAC address verification is performed only if

it is globally enabled.

Client Ifc Mismatch The number of packets that were dropped by DHCP snooping because the interface and

VLAN on which the packet was received do not match the client’s interface and VLAN

information stored in the binding database.

DHCP Server Msgs

Received The number of DHCP server messages ((DHCPOFFER, DHCPACK, DHCPNAK,

DHCPRELEASEQUERY) that were dropped on an untrusted port.

Manage dynamic ARP Inspection

Dynamic ARP Inspection (DAI) is a security feature that rejects invalid and malicious ARP

packets. DAI prevents a class of man-in-the-middle attacks where an unfriendly station

intercepts traffic for other stations by poisoning the ARP caches of its unsuspecting

neighbors. The malicious attacker sends ARP requests or responses mapping another

station’s IP address to its own MAC address.

When DAI is enabled, the switch drops ARP packets whose sender MAC address and

sender IP address do not match an entry in the DHCP snooping bindings database. You can

optionally configure additional ARP packet validation.

When DAI is enabled on a VLAN, DAI is enabled on the interfaces (physical ports or LAGs)

that are members of that VLAN. Individual interfaces are configured as trusted or untrusted.

The trust configuration for DAI is independent of the trust configuration for DHCP snooping.

Configure dynamic ARP inspection globally

If you configure the source MAC address validation option, DAI verifies that the sender MAC

address in an ARP packet equals the source MAC address in the Ethernet header.

The Ethernet header includes a configurable option to verify that the target MAC address in

the ARP packet equals the destination MAC address. This check applies only to ARP

responses, since the target MAC address is unspecified in ARP requests. You can also

enable IP address checking. When this option is enabled, DAI drops ARP packets with an

invalid IP address. The following IP addresses are considered invalid:

•0.0.0.0

•255.255.255.255

•All IP multicast addresses

•All class E addresses (240.0.0.0/4)

•Loopback addresses (in the range 127.0.0.0/8)

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual116

The valid IP check is applied only on the sender IP address in ARP packets. In ARP

response packets, the check is applied only on the target IP address.

To configure the optional DAI features:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System> Services > Dynamic ARP Inspection > DAI Configuration.

6. Select the Validate Source MAC Enable radio button.

7. Select the Validate Destination MAC Enable radio button.

8. Select the Validate IP Enable radio button.

9. Click the Apply button.

Your settings are saved.

The additional ARP validations are performed on packets received on VLANs that are

enabled for DAI and interfaces configured as untrusted.

Configure dynamic ARP inspection for a VLAN

In this example, DAI is enabled on VLAN 1. Ports 1–10 connect end users to the network and

are members of VLAN 1. These ports are configured to limit the maximum number of ARP

packets with a rate limit of 10 packets per second. LAG 1, which is also a member of VLAN 1

and contains ports 11–14, is the trunk port that connects the switch to the data center, so it is

configured as a trusted port.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual117

This example assumes that VLAN 1 and LAG 1 are already configured.

To enable dynamic ARP Inspection for VLAN1:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System> Services > Dynamic ARP Inspection > DAI VLAN Configuration.

6. In the VLAN ID column, select the check box next to VLAN 1.

7. From the Admin Mode menu, select one of the following options:

•Select Enable to enable Dynamic ARP inspection on the selected VLAN.

•Select Disable to disable Dynamic ARP inspection on the selected VLAN.

The default is Disable.

8. From the Invalid Packets menu, select one of the following options:

•Select Enable to enable logging the invalid ARP packet information for the selected

VLAN.

•Select Disable to disable dynamic ARP inspection logging for the selected VLAN.

The default is Enable.

9. In the ARP ACL Name field, enter the name of the ARP access list.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual118

A VLAN can be configured to use this ARP ACL containing rules as the filter for ARP

packet validation. The name can be 1 to 31 alphanumeric characters. The ARP ACL

name is deleted if you specify N/A.

10. From the Static Flag menu, select whether ARP packets need validation by using the

DHCP snooping database if the ARP ACL rules do not match:

•Select Enable to enable validation of ARP packets by ARP ACL rules only.

•Select Disable to enable validation of ARP packets using DHCP snooping entries.

The default is Disable.

11. Click the Apply button.

Your settings are saved.

Configure dynamic ARP inspection for a LAG and interfaces

To configure DAI on LAG1 as a trusted port and rate limiting for ports 1–10:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System> Services > Dynamic ARP Inspection > DAI Interface Configuration.

6. Click the LAG link to view all LAG interfaces.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual119

7. Next to l1, select the check box.

8. From the Trust Mode menu, select Enable to indicate that the interface is trusted.

The Trust Mode field indicates whether the interface is trusted for dynamic ARP

inspection purposes. All interfaces are untrusted by default.

9. In the Rate Limit (pps) field, specify the rate limit value for dynamic ARP inspection

purposes.

If the incoming rate of ARP packets per second exceeds the configured burst interval per

second, ARP packets are dropped. If this value is None (N/A), no limit exists. The value

can be set to –1, which means N/A. The rate limit range is 0–300. The default is 15

packets per second (pps).

10. In the Burst Interval(secs) field, specify the burst interval value for rate limiting purposes on

this interface.

If the rate limit is None, the burst interval is also nonapplicable and is displayed as N/A.

The burst interval range is 1–15 seconds. The default is 1 second.

11. Click the Apply button.

Your settings are saved.

12. To configure rate limiting for ports 1–10, which are untrusted ports, do the following:

a. Click 1 in the interface-selection field to view all ports.

b. Select each check box associated with ports 1–10.

c. In the Rate Limit (pps) field, enter 10.

13. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual120

Configure a dynamic ARP inspection ACL

DAI relies on the information in the DHCP snooping bindings database to validate ARP

packets. For networks that use static IP addresses and do not use DHCP, DAI access control

lists (ACLs) can be used to statically map an IP address to a MAC address on a VLAN. When

hosts use static IP addresses, the DHCP snooping feature cannot build a bindings database.

DAI ACLs are also useful when other switches in the network do not run DAI.

DAI consults the static mappings configured in the DAI ACLs before it consults the DHCP

snooping bindings database; thus static mappings receive precedence over DHCP snooping

bindings. If the static flag is enabled on a VLAN, DAI consults the DAI ACL only and does not

validate ARP information against the DHCP snooping bindings database.

To configure a dynamic ARP inspection ACL with three rules and associate it with

VLAN 100:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System> Services > Dynamic ARP Inspection > DAI ACL Configuration.

The DAI ACL Configuration page displays.

6. In the Name field, specify a name for the ACL.

For example, enter arpACL.

7. Click the Add button.

The page displays the new ACL.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual121

8. Click the ACL name.

The ACL name is a hyperlink to the Dynamic ARP Inspection ACL Rule Configuration

page.

9. From the ACL Name menu, select the DAI ACL to configure.

10. In the Source IP Address field, specify the IP address of a host.

11. In the Source MAC Address field, specify the MAC address of the host that is statically

mapped to the IP address specified in the Source IP Address field.

12. Click the Add button.

13. Repeat Step 10 through Step 12 to add a second rule.

You can add up to 20 static IP address–MAC address mappings to a DAI ACL.

14. Select System> Services > Dynamic ARP Inspection > DAI VLAN Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual122

15. Next to VLAN 1, select the check box.

16. In the ARP ACL Name field, specify the name of the DAI ACL to associate with the VLAN.

For example, enter arpACL.

17. Click the Apply button.

Your settings are saved.

View dynamic ARP inspection statistics for a VLAN

To view DAI statistics per VLAN:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System> Services > Dynamic ARP Inspection > DAI Statistics.

The DAI Statistics page displays.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual123

The following table describes the nonconfigurable DAI statistics information that is

displayed.

Field Description

VLAN The enabled VLAN ID for which statistics are displayed.

DHCP Drops The number of ARP packets that were dropped by DAI because no matching DHCP

snooping binding entry was found.

DHCP Permits The number of ARP packets that were forwarded by DAI because a matching DHCP

snooping binding was entry found.

ACL Drops The number of ARP packets that were dropped by DAI because no matching ARP

ACL rule was found for this VLAN and the static flag is set on this VLAN.

ACL Permits The number of ARP packets that were permitted by DAI because a matching ARP

ACL rule was found for this VLAN.

Bad Source MAC The number of ARP packets that were dropped by DAI as the sender MAC address

in the ARP packet did not match the source MAC in the Ethernet header.

Bad Dest MAC The number of ARP packets that were dropped by DAI as the target MAC address in

the ARP reply packet did not match the destination MAC in the Ethernet header.

Invalid IP The number of ARP packets that were dropped by DAI as the sender IP address in

the ARP packet, or target IP address in the ARP reply packet, is not valid. Invalid

addresses include 0.0.0.0, 255.255.255.255, IP multicast addresses, class E

addresses (240.0.0.0/4), and loopback addresses (127.0.0.0/8).

Forwarded The number of valid ARP packets forwarded by DAI.

Dropped The number of invalid ARP packets dropped by DAI.

6. Click the Update button to update the data on the page with the latest DAI statistics from the

device.

7. Click the Clear button to clear the DAI statistics.

Set up PoE timer schedules

The switch lets you define multiple timer schedules that you can use for PoE power delivery

to attached PDs.

After you create a timer schedule, you can associate it with one or more PoE ports (see

Configure the PoE port settings on page 82). You can use a separate timer schedule for

each PoE port.

After you associate a timer schedule with a PoE port, the start date and time force the PoE

port to stop delivering power and the stop date and time enable the PoE port to start

delivering power.

You can create absolute schedules, which apply to specific dates and times, and you can

create recurring schedules.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual124

Create a PoE timer schedule

The maximum number of timer schedules that you can add is 100.

To create a PoE timer schedule:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Timer Schedule > Basic > Global Configuration.

The Timer Schedule Name page displays.

6. In the Timer Schedule Name field, specify the name for a timer schedule.

7. Click the Add button.

The timer schedule is added to the table on the Timer Schedule Name page and is

assigned an ID.

Specify the settings for an absolute PoE Timer schedule

An absolute timer schedule applies to specific dates and times. The schedule is executed

once only.

To specify the settings for a PoE timer schedule that uses specific dates and times:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual125

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System> Timer Schedule > Advanced > Timer Schedule Configuration.

The Timer Schedule Configuration page displays.

6. In the Timer Schedule Selection section, make your selections from the following menus:

a. Timer Schedule Name. Select the name of the timer schedule that you want to

configure.

You can select only names of schedules that you created (see Create a PoE timer

schedule on page 124).

b. Timer Schedule Type. Select Absolute.

The fields in the Timer Schedule Configuration section might adjust to let you configure

a timer schedule for specific dates and times.

c. Timer Schedule Entry. To add a new entry, select new.

Selecting an existing entry lets you make changes to that entry.

7. In the Timer Schedule Configuration section, specify the times and dates:

a. In the Time Start field, enter the time of day in the HH:MM format to specify when the

timer schedule must start.

b. In the Time End field, enter the time of day in the HH:MM format to specify when

the timer schedule must stop.

c. Next to the Date Start field, click the calendar icon and use the menus in the pop-up

window to enter the date in the DD-Mon-YYY format to specify when the timer

schedule must start.

d. Next to the Date End field, click the calendar icon and use the menus in the pop-up

window to enter the date in the DD-Mon-YYY format to specify when the timer

schedule must stop.

8. Click the Add button.

The entry for the timer schedule is added.

Specify the settings for a recurring PoE timer schedule

A recurring schedule allows you to set up a single schedule that starts at a particular date

and that recurs either with a specific end date or indefinitely.

For a single recurring PoE timer schedule, you can add a daily, weekly, and monthly schedule

configuration. That is, these schedule configurations are not mutually exclusive but

complement each other.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual126

To specify the settings for a PoE timer schedule that uses a recurring pattern:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System> Timer Schedule > Advanced > Timer Schedule Configuration.

The Timer Schedule Configuration page displays.

6. In the Timer Schedule Selection section, make your selections from the following menus:

a. Timer Schedule Name. Select the name of the timer schedule that you want to

configure.

You can select only names of schedules that you created (see Create a PoE timer

schedule on page 124).

b. Timer Schedule Type. Select Periodic.

The fields in the Timer Schedule Configuration section might adjust to let you configure

a timer schedule with a recurrence pattern.

c. Timer Schedule Entry. To add a new entry, select new.

Selecting an existing entry lets you make changes to that entry.

7. In the Timer Schedule Configuration section, specify the recurrence pattern:

a. In the Time Start field, enter the time of day in the HH:MM format to specify when the

timer schedule must start.

b. In the Time End field, enter the time of day in the HH:MM format to specify when the

timer schedule must stop.

c. Next to the Date Start field, click the calendar icon and use the menus in the pop-up

window to enter the date in the DD-Mon-YYY format to specify when the timer

schedule must start.

d. Either select the No End Date radio button or select the End Date radio button, and

next to the End Date field, click the calendar icon and use the menus in the pop-up

window to enter the date in the DD-Mon-YYY format to specify when the timer

schedule must stop.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual127

e. From the Recurrence Pattern menu, select the pattern:

• Daily. The timer schedule works with daily recurrence. The fields adjust.

Either select the Every Weekday radio button to let the schedule operate from

Monday through Friday or select the Every Day(s) radio button and enter a

number from 0 to 255 in the field.

In the latter case, the schedule is triggered every specified number of days. If the

number of days is not specified, or if you enter 0, then the schedule is triggered

only once.

• Weekly. The timer schedule works with weekly recurrence. The fields adjust.

In the Every Week(s) field, enter a number from 0 to 255 to specify that the

schedule must be triggered every specified number of weeks. If the number of

weeks is not specified, or if you enter 0, then the schedule is triggered only once.

Select a single Week Day check box, multiple check boxes, or all check boxes to

specify the day or days of the week that the schedule must operate.

• Monthly. The timer schedule works with monthly recurrence. The fields adjust.

In the Day field, enter a number from 1 to 31 to specify the day of the month when

the schedule must be triggered.

In the Every Month(s) field, enter a number from 0 to 255 to specify that the

schedule must be triggered every specified number of months. If the number of

months is not specified, or if you enter 0, then the schedule is triggered only once.

8. Click the Add button.

The entry for the timer schedule is added.

Change the settings for a recurring PoE timer schedule

entry

You can change the settings for an existing recurring PoE timer schedule entry. (You cannot

do this for an existing absolute PoE timer schedule.)

To change the settings for an existing recurring PoE timer schedule entry:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual128

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Timer Schedule > Advanced > Timer Schedule Configuration.

The Timer Schedule Configuration page displays.

6. From the Timer Schedule Name menu, select the schedule name.

7. From the Timer Schedule Type menu, select the schedule type.

8. From the Timer Schedule Entry menu, select the schedule entry.

9. Make the changes to the schedule entry.

For more information, see Specify the settings for a recurring PoE timer schedule on

page 125.

10. Click the Apply button.

Your settings are saved.

Delete a PoE timer schedule entry

You can delete a PoE timer schedule entry that you no longer need.

To delete a PoE timer schedule entry:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Timer Schedule > Advanced > Timer Schedule Configuration.

The Timer Schedule Configuration page displays.

6. From the Timer Schedule Name menu, select the schedule name.

7. From the Timer Schedule Type menu, select the schedule type.

8. From the Timer Schedule Entry menu, select the schedule entry.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure System Information User Manual129

9. Click the Delete button.

The entry is deleted.

Delete a PoE timer schedule

You can delete a PoE timer schedule that you no longer need. All entries that are part of the

PoE timer schedule are also deleted.

To delete a PoE timer schedule:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select System > Timer Schedule > Basic > Global Configuration.

The Timer Schedule Name page displays.

6. Select the check box for the schedule that you want to delete.

7. Click the Delete button.

The schedule is deleted.

130

3Configure Switching

This chapter covers the following topics:

•Configure the port settings

•Configure link aggregation groups

•Configure VLANs

•Configure a voice VLAN

•Configure Auto-VoIP

•Configure Spanning Tree Protocol

•Configure multicast

•Manage IGMP snooping

•Manage MLD snooping

•Configure multicast VLAN registration

•View, search, and manage the MAC address table

•Configure Layer 2 loop protection

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual131

Configure the port settings

You can view, configure, and monitor the physical port information for the ports (that is, the

physical interfaces) on the switch.

To configure the port settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > Ports > Port Configuration.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8. In the Description field, enter the description string to be attached to a port.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual132

The string can be up to 64 characters in length.

9. From the Admin Mode menu, select Enable or Disable.

This sets the port control administrative mode. You must select Enable in order for the

port to participate in the network. The default is Enable.

10. From the Auto-negotiation menu, select Enable or Disable.

This specifies the autonegotiation mode for this port. The default is Enable.

Note: After you change the autonegotiation mode, the switch might be

inaccessible for a number of seconds while the new settings take

effect.

11. In the Speed field, specify the speed value for the selected port.

Possible field values are as follows:

• Auto. All supported speeds.

•1

0. 10 Mbits/second

• 100. 100 Mbits/second

The delimiter characters for setting different speed values are a comma (,), a period (.)

and a space ( ). For you to set the auto-negotiation speed, the autonegotiation mode

must be set to Enable. The default is Auto.

Note: After you change the speed value, the switch might be inaccessible for

a number of seconds while the new settings take effect.

12. From the Duplex Mode menu, select the duplex mode for the selected port.

Possible values are as follows:

• Auto. Indicates that speed is set by the auto-negotiation process.

• Full. Indicates that the interface supports transmission between the devices in both

directions simultaneously.

•Half. Indicates that the interface supports transmission between the devices in only

one direction at a time.

The default is Auto.

Note: After you change the duplex mode, the switch might be inaccessible for

a number of seconds while the new settings take effect.

13. Use the Link Trap menu to specify whether or not to send a trap when link status changes.

The Link Trap menu is enabled by default. However, for LAG interfaces, the menu is

disabled.

14. In the Frame Size field, specify the maximum Ethernet frame size the interface supports or

is configured to use, including Ethernet header, CRC, and payload.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual133

The range is 1500 to 9198. The default maximum frame size is 1500.

15. From the Flow Control menu, select the configuration for IEEE 802.3 flow control.

• Disable. If the port buffers become full, the switch does not send pause frames, and

data loss could occur. This is the default setting.

• Symmetric. If the port buffers become full, the switch sends pause frames to stop

traffic.

Flow control helps to prevent data loss when the port cannot keep up with the number

of frames being switched. When you enable flow control, the switch can send a pause

frame to stop traffic on the port if the amount of memory used by the packets on the

port exceeds a preconfigured threshold and responds to pause requests from partner

devices. The paused port does not forward packets for the time that is specified in the

pause frame. When the pause frame time elapses, or the utilization returns to a

specified low threshold, the switch enables the port to again transmit frames. The

switch also honors incoming pause frames by temporarily halting transmission.

• Asymmetric. If the port buffers become full, the switch does not send pause frames,

and data loss could occur . However , the switch does honor incoming pause frames by

temporarily halting transmission.

Note: For LAG interfaces, flow control mode is displayed as a blank field

because flow control is not applicable.

16. Click the Apply button.

Your settings are saved.

The following table describes the nonconfigurable data that is displayed.

Table 30. Port Configuration information

Field Description

Port Type For normal ports this field is blank. Otherwise, the possible values are as

follows:

Physical Status The port speed and duplex mode.

Link Status Indicates whether the link is up or down.

MAC Address The physical address of the specified interface.

PortList Bit Offset The bit offset value that corresponds to the port when the MIB object type

PortList is used to manage in SNMP.

ifIndex The ifIndex of the interface table entry associated with this port.

• Mirrored. The port is a mirrored port on which all the traffic is copied

to the probe port.

• Probe. Use this port to monitor a mirrored port.

• Trunk Member. The port is a member of a link aggregation trunk.

Look at the LAG pages for more information.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual134

Configure link aggregation groups

Link aggregation groups (LAGs), which are also known as port channels, allow you to

combine multiple full-duplex Ethernet links into a single logical link. Network devices treat the

aggregation as if it were a single link, which increases fault tolerance and provides load

sharing. You assign the LAG VLAN membership after you create a LAG. The LAG by default

becomes a member of the default management VLAN (that is, VLAN 1).

A LAG interface can be either static or dynamic, but not both. All members of a LAG must

participate in the same protocols. A static port channel interface does not require a partner

system to be able to aggregate its member ports.

The switch supports static LAGs. When a port is added to a LAG as a static member, the port

neither transmits nor receives LACPDUs.

Model GS418TPP supports eight LAGs. Models GS510TLP and GS510TPP support five

LAGs.

Configure the LAG settings

You can group one or more full-duplex Ethernet links to be aggregated together to form a link

aggregation group, which is also known as a port channel. The switch treats the LAG as if it

were a single link.

To configure the LAG settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> LAG > Basic > LAG Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual135

6. In the LAG Name field, enter a name for the LAG.

You can enter any string of up to 15 alphanumeric characters. A valid name must be

specified for you to create the LAG.

7. In the Description field, enter the description string to be attached to a LAG.

The description can be up to 64 characters in length.

8. From the Admin Mode menu, select Enable or Disable.

When the LAG is disabled, no traffic flows and LACPDUs are dropped, but the links that

form the LAG are not released. The default is Enable.

9. From the Hash Mode menu, select the load-balancing mode for a port channel (LAG):

• 1 Src MAC, VLAN, EType, incoming port. This mode uses the source MAC

address, VLAN, EtherType, and incoming port that are associated with the packet.

•2 Dest MAC, VLAN, EType, incoming port. This mode uses the destination MAC

address, VLAN, EtherType, and incoming port that are associated with the packet.

•3 Src/Dest MAC, VLAN, EType, incoming port. This mode uses the source and

destination MAC addresses, VLAN, EtherT ype, and incoming port that are associated

with the packet. This is the default mode.

• 4 Src IP and Src TCP/UDP Port Fields. This mode uses the source IP address and

source TCP or UDP port value that are associated with the packet.

•5 Dest IP and Dest TCP/UDP Port Fields. This mode uses the destination IP

address and destination TCP or UDP port value that are associated with the packet.

•6 Src/Dest IP and TCP/UDP Port Fields. This mode uses the source and destination

IP addresses and source and destination TCP or UDP port values that are associated

with the packet.

Note: The switch balances traffic on a port channel (LAG) by selecting one

of the links in the channel over which packets must be transmitted. The

switch selects the link by creating a binary pattern from selected fields

in a packet and associating that pattern with a particular link.

10. From the STP Mode menu, select the Spanning Tree Protocol (STP) administrative mode

associated with the LAG. The possible values are as follows:

• Disable. Spanning tree is disabled for this LAG.

• Enable. Spanning tree is enabled for this LAG. Enable is the default.

11. From the Link Trap menu, select Enable or Disable to specify whether to send a trap when

the link status changes.

The default is Enable, which causes the trap to be sent.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual136

12. From the LAG Type menu, select Static or LACP:

• Static. Disables Link Aggregation Control Protocol (LACP) on the selected LAG. The

LAG is configured manually. The default is Static.

• LACP. Disables LACP on the selected LA. The LAG is configured automatically.

13. Click the Apply button.

Your settings are saved.

The following table describes the nonconfigurable information displayed on the page.

Table 31. LAG Configuration information

Field Description

LAG ID Identification of the LAG.

Active Ports Indicates the ports that are actively participating in the port channel.

LAG State Indicates whether the link is up or down.

Configure LAG membership

You can select two or more full-duplex Ethernet links to be aggregated together to form a link

aggregation group (LAG), which is also known as a port channel. The switch can treat the

port channel as a single link.

To configure LAG membership:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> LAG > Basic > LAG Membership.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual137

6. From the LAG ID menu, select the LAG ID.

7. In the LAG Name field, enter the name to be assigned to the LAG.

You can enter any string of up to 15 alphanumeric characters. A valid name must be

specified for you to create the LAG.

8. In the Ports table, click each port that you want to include as a member of the selected

LAG.

A selected port is displayed by a check mark.

9. Click the Apply button.

Your settings are saved.

Set the LACP system priority

The LACP configuration page is used to set the LACP system priority.

To configure the LACP:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> LAG > Advanced > LACP Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual138

6. In the LACP System Priority field, specify the device’s link aggregation priority relative to

the devices at the other ends of the links on which link aggregation is enabled.

A higher value indicates a lower priority. You can change the value of the setting globally

by specifying a priority from 1 to 65535. The default value is 32768.

7. Click the Apply button.

Your settings are saved.

Set the LACP port priority settings

The LACP port configuration page is used to configure the LACP priority value for the selected

port and the administrative LACP time-out value.

To configure LACP port priority settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> LAG > Advanced > LACP Port Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual139

6. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the interface, or

type the interface number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

7. In the LACP Priority field, specify the LACP priority value for the selected interfaces.

This value specifies the device’s link aggregation priority relative to the devices at the

other ends of the links on which link aggregation is enabled. A higher value indicates a

lower priority. The range is 1 to 65535. The default value is 128.

8. In the Timeout field, configure the administrative LACP time-out value:

• Long. Specifies a long time-out value.

•Short. Specifies a short time-out value.

9. Click the Apply button.

Your settings are saved.

Configure VLANs

Adding virtual LAN (VLAN) support to a Layer 2 switch offers some of the benefits of both

bridging and routing. Like a bridge, a VLAN switch forwards traffic based on the Layer 2

header, which is fast, and like a router, it partitions the network into logical segments, which

provides better administration, security, and management of multicast traffic.

By default, all ports on the switch are in the same broadcast domain. VLANs electronically

separate ports on the same switch into separate broadcast domains so that broadcast

packets are not sent to all the ports on a single switch. When you use a VLAN, users can be

grouped by logical function instead of physical location.

Each VLAN in a network is assigned an associated VLAN ID, which appears in the IEEE

802.1Q tag in the Layer 2 header of packets transmitted on a VLAN. An end station can omit

the tag, or the VLAN portion of the tag, in which case the first switch port to receive the

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual140

packet can either reject it or insert a tag using its default VLAN ID. A given port can handle

traffic for more than one VLAN, but it can support only one default VLAN ID.

You can define VLAN groups stored in the VLAN membership table. The switch supports up

to 256 VLANs. VLAN 1 is created by default and is the default VLAN of which all ports are

members.

Configure the VLAN Settings

Add a VLAN

To add a VLAN:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> VLAN > Basic > VLAN Configuration.

6. In the VLAN ID field, specify the VLAN identifier for the new VLAN.

The range of the VLAN ID can be from 1 to 4093.

7. In the VLAN Name field, specify a name for the VLAN.

The VLAN name can be up to 32 alphanumeric characters long, including blanks. The

default is blank. VLAN ID 1 always uses the name Default.

8. The VLAN Type field displays the type of the VLAN that you are configuring.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual141

You cannot change the type of the default VLAN (VLAN ID = 1): it is always type Default.

When you create a VLAN using this page, its type is always Static. A VLAN that is

created by GVRP registration initially uses a type of Dynamic. When configuring a

dynamic VLAN, you can change its type to Static.

9. Click the Add button.

The VLAN is added to the switch.

10. Click the Apply button.

Your settings are saved.

Delete a VLAN

To delete a VLAN from the switch:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> VLAN > Basic > VLAN Configuration.

The VLAN Configuration page displays.

6. In the VLAN ID field, specify the VLAN identifier.

The range of the VLAN ID can be from 1 to 4093.

Note: You cannot delete VLANs 1 and VLAN 4089, which are created by

default.

7. Click the Delete button.

The VLAN is removed.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual142

Reset a VLAN to its default settings

To reset a VLAN to its default settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> VLAN > Basic > VLAN Configuration.

You can also select Switching> VLAN > Advanced > VLAN Configuration.

The VLAN Configuration page displays.

6. Select the Reset Configuration check box.

7. Click the Apply button.

Your settings are saved.

The default values are as follows:

•All ports are assigned to the default VLAN of 1.

•All ports are configured with a PVID of 1.

•All ports are configured to an Acceptable Frame Types value of Admit All Frames.

•All ports are configured with ingress filtering disabled.

•All ports are configured to transmit only untagged frames.

•GVRP is disabled on all ports and all dynamic entries are cleared.

All VLANs, except for the default VLAN, are deleted.

Configure VLAN membership

To configure VLAN membership:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual143

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > VLAN > Advanced > VLAN Membership.

6. In the VLAN ID menu, select the VLAN ID.

7. In the Group Operation menu, select one of the following options, which applies to all ports

in the VLAN:

• Untag All. For all ports that are members of the VLAN, tags are removed from all

egress packets.

• T ag All. For all ports that are members of the VLAN, all egress packets are tagged.

• Remove All. All ports that were dynamically registered through GVRP are removed

from the VLAN.

8. In the Ports table, click each port once, twice, or three times to configure one of the following

modes or reset the port to the default settings:

• T (T agged). Select the ports on which all frames transmitted for this VLAN are tagged.

The ports that are selected are included in the VLAN.

• U (Untagged). Select the ports on which all frames transmitted for this VLAN are

untagged. The ports that are selected are included in the VLAN.

By default, the selection is blank, which means that the port is excluded from the VLAN

but can be dynamically registered (autodetected) in the VLAN through GVRP.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual144

9. In the LAG table, click each LAG once, twice, or three times to configure one of the following

modes or reset the LAG to the default settings:

• T (Tagged). Select the LAGs on which all frames transmitted for this VLAN are

tagged. The LAGs that are selected are included in the VLAN.

• U (Untagged). Select the LAGs on which all frames transmitted for this VLAN are

untagged. The LAGs that are selected are included in the VLAN.

By default, the selection is blank, which means that the LAG is excluded from the VLAN

but can be dynamically registered (autodetected) in the VLAN through GVRP.

10. Click the Apply button.

Your settings are saved.

The following table describes the nonconfigurable information displayed on the page.

Table 32. Advanced VLAN membership

Field Definition

VLAN Name The name for the VLAN that you selected. It can be up to 32

alphanumeric characters long, including blanks. VLAN ID 1 always

uses the name Default.

VLAN Type The type of the VLAN you selected:

View the VLAN status

You can view the status of all currently configured VLANs.

To view the VLAN status:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

• Default (VLAN ID = 1). Always present.

• Static. A VLAN that you configured.

• Dynamic. A VLAN created by GVRP registration that you did not

convert to static, and that GVRP can therefore remove.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual145

5. Select Switching > VLAN > Advanced > VLAN Status.

The following table describes the nonconfigurable information displayed on the page.

Table 33. VLAN status

Field Definition

VLAN ID The VLAN identifier (VID) of the VLAN. The range of the VLAN ID is 1

to 4093.

VLAN Name The name of the VLAN. VLAN ID 1 is always named Default.

VLAN Type The VLAN type:

Routing Interface The interface associated with the VLAN, in the case that VLAN routing

is configured for this VLAN.

Member Ports The ports that are included in the VLAN.

Configure the port PVID settings

You can assign a port VLAN ID (PVID) to an interface. The following requirements apply to a

PVID:

•You must define a PVID for all ports.

•If no other value is specified, the default VLAN PVID is used.

•To change the port’s default PVID, you must first create a VLAN that includes the port as

a member (see Configure VLAN membership on page 142).

To configure the PVID settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

• Default (VLAN ID = 1). Always present.

• Static. A VLAN that you configured.

• Dynamic. A VLAN created by GVRP registration that you did not

convert to static, and that GVRP can therefore remove.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual146

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> VLAN > Advanced > Port PVID Configuration.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8. In the PVID field, specify the VLAN ID to assign to untagged or priority-tagged frames

received on this port.

The default is 1.

9. In the VLAN Member field, specify the VLAN ID or list of VLANs of a member port.

VLAN IDs range from 1 to 4093. The default is 1. Use a hyphen (-) to specify a range or a

comma (,) to separate VLAN IDs in a list. Spaces and zeros are not permitted.

10. In the VLAN Tag field, specify the VLAN ID or list of VLANs of a tagged port.

VLAN IDs range from 1 to 4093. Use a hyphen (-) to specify a range or a comma (,) to

separate VLAN IDs in a list. Spaces and zeros are not permitted. To reset the VLAN tag

configuration to the defaults, use the None keyword. Port tagging for the VLAN can be

set only if the port is a member of this VLAN.

11. From the Acceptable Frame menu, specify the types of frames that can be received on this

port.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual147

The options are VLAN only and Admit All:

• VLAN only. Untagged frames or priority-tagged frames received on this port are

discarded.

• Admit All. Untagged frames or priority-tagged frames received on this port are

accepted and assigned the value of the port VLAN ID for this port. With either option,

VLAN-tagged frames are forwarded in accordance to the 802.1Q VLAN specification.

12. From the Ingress Filtering menu, select one of the following options:

• Enable. The frame is discarded if this port is not a member of the VLAN with which

this frame is associated. In a tagged frame, the VLAN is identified by the VLAN ID in

the tag. In an untagged frame, the VLAN is the port VLAN ID specified for the port that

received this frame.

• Disable. All frames are forwarded in accordance with the 802.1Q VLAN bridge

specification. The default is Disable.

13. In the Port Priority field, specify the default 802.1p priority assigned to untagged packets

arriving at the port.

You can enter a number from 0 to 7.

14. Click the Apply button.

Your settings are saved.

The following table describes the nonconfigurable fields.

Table 34. Nonconfigurable fields on the PVID Configuration page

Field Description

Current Ingress Filtering Indicates whether ingress filtering is enabled for the interface.

Untagged VLANs The number of untagged VLANs for the interface.

Tagged VLANs The number of tagged VLANs for the interface.

Forbidden VLANs The number of forbidden VLANs for the interface.

Dynamic VLANs The number of dynamically added VLANs for the interface.

Configure a MAC-based VLAN

The MAC-Based VLAN feature allows incoming untagged packets to be assigned to a VLAN

and thus classify traffic based on the source MAC address of the packet.

You define a MAC-to-VLAN mapping by configuring an entry in the MAC-to-VLAN table. An

entry is specified through a source MAC address and the desired VLAN ID. The

MAC-to-VLAN configurations are shared across all ports of the device (that is, a system-wide

table exists with MAC address–to–VLAN ID mappings).

When untagged or priority-tagged packets arrive at the switch and entries exist in the

MAC-to-VLAN table, the source MAC address of the packet is looked up. If an entry is found,

the corresponding VLAN ID is assigned to the packet. If the packet is already priority tagged

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual148

it maintains this value. Otherwise, the priority is set to zero. The assigned VLAN ID is verified

against the VLAN table. If the VLAN is valid, ingress processing on the packet continues.

Otherwise, the packet is dropped. This implies that the user is allowed to configure a MAC

address mapping to a VLAN that was not created on the system.

Add a MAC-based VLAN

To add a MAC-based VLAN:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> VLAN > Advanced > MAC Based VLAN.

6. In the MAC Address field, enter a valid MAC address to be bound to a VLAN ID.

This field is configurable only when a MAC-based VLAN is created.

7. In the VLAN ID field, specify a VLAN ID in the range of 1 to 4093.

8. Click the Add button.

The MAC address is added to the VLAN mapping.

Delete a MAC address from the VLAN mapping

To delete a MAC address from the VLAN mapping:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual149

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> VLAN > Advanced > MAC Based VLAN.

The MAC Based VLAN Configuration page displays.

6. In the MAC Address field, enter a valid MAC address.

This field is configurable only when a MAC-based VLAN exists.

7. In the VLAN ID field, specify a VLAN ID in the range of 1 to 4093.

8. Click the Delete button.

The MAC address is removed from the VLAN mapping.

Configure protocol-based VLAN groups

You can use a protocol-based VLAN to define filtering criteria for untagged packets. By

default, if you do not configure any port-based (IEEE 802.1Q) or protocol-based VLANs,

untagged packets are assigned to VLAN 1. You can override this behavior by defining either

port-based VLANs or protocol-based VLANs, or both. Tagged packets are always handled

according to the IEEE 802.1Q standard and are not included in protocol-based VLANs.

If you assign a port to a protocol-based VLAN for a specific protocol, untagged frames

received on that port for that protocol are assigned the protocol-based VLAN ID. Untagged

frames received on the port for other protocols are assigned the port VLAN ID, either the

default PVID (1) or a PVID you specifically assigned to the port using the Port VLAN

Configuration page.

You define a protocol-based VLAN by creating a group. Each group forms a one-to-one

relationship with a VLAN ID, can include one to three protocol definitions, and can include

multiple ports. When you create a group, you specify a name and a group ID is assigned

automatically.

To configure a protocol-based VLAN group:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual150

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> VLAN > Advanced > Protocol Based VLAN Group Configuration.

6. In the Group Name field, type a name for the new group.

You can enter up to 16 characters.

7. In the Protocol field, enter one or more protocols that must be associated with the group.

You can enter keywords such as arp, ip, and ipx. Separate keywords with a comma. You

can also enter hexadecimal or decimal values in the range of 0x0600 (1536) to 0xFFFF

(65535).

8. In the VLAN ID field, enter the VLAN ID.

The ID can be any number in the range of 1 to 4093. All the ports in the group assign this

VLAN ID to untagged packets received for the protocols that you included in this group.

9. Click the Add button.

The protocol-based VLAN group is added to the switch.

10. Click the Apply button.

Your settings are saved.

The following table describes the nonconfigurable information displayed on the page.

Table 35. Protocol Based VLAN Group Configuration information

Field Description

Group ID A number used to identify the group created by the user. Group IDs are

automatically assigned when a group is created by the user.

Ports Display all the member ports that belong to the group.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual151

Configure protocol-based VLAN group membership

To configure protocol-based VLAN group membership:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> VLAN > Advanced > Protocol Based VLAN Group Membership.

6. From the Group ID menu, select the protocol-based VLAN group ID.

The Group Name field shows the name that is associated with the group.

7. In the Ports table and LAG table, click each port and LAG that you want to include in the

protocol-based VLAN group.

A protocol-based VLAN group can include both port and LAGs. A selected port or LAG is

displayed by a check mark.

8. Click the Apply button

Your settings are saved.

9. To show the current numbers in the selected protocol-based VLAN group, click the Current

Members button.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual152

Configure a voice VLAN

You can configure the settings for a voice VLAN configuration.

To configure a voice VLAN:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> VLAN > Advanced > Voice VLAN Configuration.

6. Select the Admin Mode Disable or Enable radio button.

This specifies the administrative mode for the voice VLAN for the switch. The default is

Disable.

7. Select the interface by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual153

8. From the Interface Mode menu, select the voice VLAN mode for selected interfaces:

• Disable. This is the default value.

•None. Allow the IP phone to use its own configuration to send untagged voice traffic.

•VLAN ID. Configure the phone to send tagged voice traffic.

•dot1p. Configure voice VLAN 802.1p priority tagging for voice traffic. When this is

selected, enter the dot1p value in the Value field.

• Untagged. Configure the phone to send untagged voice traffic.

9. In the Value field, enter the VLAN ID or dot1p value.

This field is enabled only when VLAN ID or dot1p is selected as the interface mode.

10. In the CoS Override Mode field, select Disable or Enable.

The default is Disable.

11. In the Authentication Mode field, select Enable or Disable.

The default is Enable. When the authentication mode is enabled, voice traffic is allowed

on an unauthorized voice VLAN port. When the authentication mode is disabled, devices

are authorized through dot1x.

Note: Authentication through dot1x is possible only if dot1x is enabled.

12. In the DSCP Value field, configure the Voice VLAN DSCP value for the port.

The valid range is 0 to 64. The default value is 0.

The Operational State field displays the operational status of the voice VLAN on the given

interface.

13. Click the Apply button.

Your settings are saved.

Configure GARP switch settings

The Generic Attribute Registration Protocol (GARP) is used to exchange information

between GARP participants to register and deregister attribute values within a bridged LAN.

When a GARP participant declares or withdraws a given attribute, the attribute value is

recorded with the applicant state machine for that attribute, for the port from which the

declaration or withdrawal was made.

•Registration occurs only on ports that receive the GARP PDU containing a declaration or

withdrawal.

•Deregistration occurs only if all GARP participants connected to the same LAN segment

as the port withdraw the declaration.

GARP is part of the IEEE 802.1p extension to its 802.1D (spanning tree) specification. It

includes the following:

• GARP Information Declaration (GID). The part of GARP that generates data.

•GARP Information Propagation (GIP). The part of GARP that distributes data.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual154

Note: It can take up to 10 seconds for the GARP configuration changes to

take effect.

To configure GARP switch settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> VLAN > Advanced > GARP Switch Configuration.

6. Select the GVRP Mode Disable or Enable radio button.

This selects the GARP VLAN registration protocol administrative mode for the switch.

The default is Disable.

7. Click the Apply button.

Your settings are saved.

Configure GARP ports

Note: It can take up to 10 seconds for the GARP configuration changes to

take effect.

To configure GARP ports:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual155

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> VLAN > Advanced > GARP Port Configuration.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.\

8. From the GVRP Mode menu, select Enable or Disable.

This specifies the GARP VLAN registration protocol administrative mode for the port. If

you select Disable, the protocol is not active and the join time, leave time, and leave all

time options are without any effect. The default is Disable.

9. In the Join Timer field, specify the time in centiseconds between the transmission of GARP

PDUs registering (or reregistering) membership for a VLAN or multicast group.

Enter a number between 10 and 100 (0.1 to 1.0 seconds). The default is 20 centiseconds

(0.2 seconds). An instance of this timer exists for each GARP participant for each port.

10. In the Leave Timer field, specify the time in centiseconds to wait after receiving an

unregister request for a VLAN or multicast group before deleting the associated entry.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual156

This allows time for another station to assert registration for the same attribute to maintain

uninterrupted service. Enter a number between 20 and 600 (0.2 to 6.0 seconds). The

default is 60 centiseconds (0.6 seconds). An instance of this timer exists for each GARP

participant for each port.

11. In the Leave All Timer field, specify how frequently (in centiseconds) LeaveAll PDUs are

generated.

A LeaveAll PDU indicates that all registrations will be deregistered soon. To maintain

registration, participants must rejoin. The leave all period timer is set to a random value in

the range of LeaveAllTime to 1.5 * LeaveAllTime. The timer is specified in centiseconds.

Enter a number between 200 and 6000 (2 to 60 seconds). The default is 1000

centiseconds (10 seconds). An instance of this timer exists for each GARP participant for

each port.

12. Click the Apply button.

Your settings are saved.

Configure Auto-VoIP

Voice over Internet Protocol (VoIP) enables telephone calls over a data network. Because

voice traffic is typically more time-sensitive than data traffic, the Auto-VoIP feature helps

provide a classification mechanism for voice packets so that they can be prioritized above

data packets in order to provide better Quality of Service (QoS). With the Auto-VoIP feature,

voice prioritization is provided based on call-control protocols (SIP, SCCP, H.323) or OUI bits.

Configure Auto-VoIP protocol-based settings

To prioritize time-sensitive voice traffic over data traffic, protocol-based Auto-VoIP checks for

packets carrying the following VoIP protocols:

•Session Initiation Protocol (SIP)

•H.323

•Signalling Connection Control Part (SCCP)

VoIP frames that are received on ports that for which the Auto-VoIP feature is enabled are

marked with the specified CoS traffic class value.

To configure Auto-VoIP protocol-based settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual157

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > Auto-VoIP > Protocol-based > Port Settings.

6. In the Protocol Based Global Settings section, specify the following global settings:

a. From the Prioritization Type menu, select Traffic Class or Remark.

This specifies the type of prioritization.

b. From the Class Value menu, specify the CoS class value to be reassigned for packets

that the voice VLAN receives.

7. In the Protocol Based Global Settings section, specify the Auto VoIP Mode settings:

a. Select whether to display physical interfaces, LAGs, or both by clicking one of the

following links above the table heading:

•1

(the unit ID of the switch). Only physical interfaces are displayed. This is the

default setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

b. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or

type the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the

heading row.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual158

c. From the Auto VoIP Mode menu, select to enable or disable the Auto VoIP mode

for the interface or interfaces.

8. Click the Apply button.

Your settings are saved.

Configure the Auto-VoIP OUI-based properties

With Organizationally Unique Identifier (OUI)–based Auto-VoIP, voice prioritization is

provided based on OUI bits.

To configure the Auto-VoIP OUI-based properties:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > Auto-VoIP > OUI-based > Properties.

6. In the Auto-VoIP VLAN ID field, enter the VoIP VLAN ID of the switch.

No default VLAN exists for Auto-VoIP, you must create a VLAN for Auto-VoIP.

7. From the OUI-based priority menu, select the OUI-based priority of the switch.

The default value is 7.

8. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual159

Configure the OUI-based port settings

The port settings page allows you to configure the OUI port settings.

To configure the OUI-based port settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > Auto-VoIP > OUI-based > Port Settings.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8. From the Auto VoIP Mode menu, select Disable or Enable.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual160

Auto-VoIP is disabled by default.

The Operational Status field displays the current operational status of each interface.

9. Click the Apply button.

Your settings are saved.

Manage the OUI table

Device hardware manufacturers can include an OUI in a network adapter to help identify a

hardware device. The OUI is a unique 24-bit number assigned by the IEEE registration

authority. The switch comes preconfigured with the following OUIs that identify the IP phone

manufacturer:

•00:01:E3: SIEMENS

•00:03:6B: CISCO1

•00:12:43: CISCO2

•00:0F:E2: H3C

•00:60:B9: NITSUKO

•00:D0:1E: PINTEL

•00:E0:75: VERILINK

•00:E0:BB: 3COM

•00:04:0D: AVAYA1

•00:1B:4F: AVAYA2

•00:04:13: SNOM

You can select an existing OUI or add a new OUI and description to identify the IP phones on

the network.

Configure the OUI table

To configure the OUI Table:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual161

The default password is password.

The System Information page displays.

5. Select Switching > Auto-VoIP > OUI-based > OUI Table.

6. In the Telephony OUI(s) field, specify the VoIP OUI prefix to be added in the format

AA:BB:CC.

Up to 128 OUIs can be configured.

7. In the Description field, enter the description for the OUI.

The maximum length of description is 32 characters. The following OUIs are present in

the configuration by default:

•00:01:E3 - SIEMENS

•00:03:6B - CISCO1

•00:12:43 - CISCO2

•00:0F:E2 - H3C

•00:60:B9 - NITSUKO

•00:D0:1E - PINTEL

•00:E0:75 - VERILINK

•00:E0:BB - 3COM

•00:04:0D - AVAYA1

•00:1B:4F - AVAYA2

8. Click the Add button.

The telephony OUI entry is added.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual162

Delete one or more OUI prefixes from the OUI table

To delete one or more OUI prefixes from the OUI table:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > Auto-VoIP > OUI-based > OUI Table.

The OUI Table page displays.

6. Select the check box next to each OUI prefix to be removed.

7. Click the Delete button.

The telephony OUI entries are removed.

Display the Auto-VoIP status

You can display the Auto-VoIP status.

To view the Auto-VoIP status:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual163

5. Select Switching > Auto-VoIP > Auto-VoIP Status.

6. To refresh the page with the latest information about the switch, click the Update button.

The following table describes the nonconfigurable Auto-VoIP status information.

Table 36. Auto-VoIP status

Field Description

Auto-VoIP VLAN ID The Auto-VoIP VLAN ID.

Maximum Number of Voice

Channels Supported The maximum number of voice channels supported.

Number of Voice Channels

Detected The number of VoIP channels prioritized successfully.

Configure Spanning Tree Protocol

The Spanning Tree Protocol (STP) provides a tree topology for any arrangement of network

devices. STP also provides one path between end stations on a network, eliminating loops.

STP (also referred to as “classic” STP) provides a single path between end stations, avoiding

and eliminating loops. For information about configuring the global STP settings for the

switch, see Configure the STP settings and view the STP status on page 164.

The switch support the following spanning tree versions:

• CST. Common STP. For information on configuring CST, see Configure the CST settings

on page 166 and Configure the CST port settings on page 167.

• MSTP. Multiple Spanning Tree Protocol (MSTP, also referred to as MST) supports

multiple instances of spanning tree to efficiently channel VLAN traffic over different

interfaces. For information on configuring MSTP, see Manage the MST settings on

page 172 and Configure and view the port settings for an MST instance on page 175.

• RSTP. Rapid STP. Each instance of the spanning tree behaves in the manner specified in

IEEE 802.1w, Rapid Spanning Tree (RSTP), with slight modifications in the working but

not the end effect (chief among the effects is the rapid transitioning of the port to the

forwarding state). For information on viewing the RSTP state, see View Rapid STP

Information on page 171.

The difference between the RSTP and the traditional STP (IEEE 802.1D) is the ability to

configure and recognize full-duplex connectivity and ports that are connected to end

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual164

stations, resulting in rapid transitioning of the port to the forwarding state and the

suppression of Topology Change Notification. These features are represented by the

pointtopoint and edgeport parameters. MSTP is compatible with both RSTP and STP. It

behaves in a way that is appropriate for STP and RSTP bridges. An MSTP bridge can be

configured to behave entirely as an RSTP bridge or an STP bridge.

Note: For two bridges to be in the same region, the force version must be

802.1s and their configuration names, digest keys, and revision levels

must match. For additional information about regions and their effect

on network topology, refer to the IEEE 802.1Q standard.

Configure the STP settings and view the STP status

You can configure the STP settings and view the STP status on the switch.

To configure the STP settings and view the STP status:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > STP > Basic > STP Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual165

6. Configure the following options:

• Spanning Tree State. Enable or disable the spanning tree operation on the switch.

• STP Operation Mode. Specify the STP version for the switch. The options are STP,

RSTP, and MSTP.

• Configuration Name. Specify an identifier used to identify the configuration currently

being used. It can be up to 32 alphanumeric characters.

• Configuration Revision Level. Specify an identifier used to identify the configuration

currently being used. The values allowed are between 0 and 65535. The default value

is 0.

• Forward BPDU while STP Disabled. Enable or disable the BPDU Flood. This

specifies whether spanning tree BPDUs are forwarded or not while spanning tree is

disabled on the switch.

7. Click the Apply button.

Your settings are saved.

The following table describes the nonconfigurable STP Status fields displayed on the page.

Table 37. STP configuration status

Field Description

Configuration Digest Key Identifier used to identify the configuration currently being used.

STP Status

Bridge Identifier The bridge identifier for the CST. It is made up using the bridge priority and

the base MAC address of the bridge.

Time Since Topology Change The time in day-hour-minute-second format since the topology of the CST

last changed.

Topology Change Count The number of times that the topology changed for the CST.

Topology Change The value of the topology change parameter for the switch indicating

whether a topology change is in progress on any port assigned to the CST.

Possible values are True and False.

Designated Root The bridge identifier of the root bridge. It is made up from the bridge priority

and the base MAC address of the bridge.

Root Path Cost Path cost to the designated root for the CST.

Root Port Port to access the designated root for the CST.

Max Age (secs) The maximum age timer controls the maximum length of time in seconds

that passes before a bridge port saves its configuration BPDU information.

Forward Delay (secs) The derived value of the Root Port Bridge Forward Delay parameter.

Hold T ime (secs) Minimum time in seconds between the transmission of configuration

BPDUs.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual166

Configure the CST settings

You can configure a common spanning tree (CST) and internal spanning tree on the switch.

To configure the CST settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > STP > Advanced > CST Configuration.

6. Specify the CST options:

• Bridge Priority. When switches or bridges are running STP, each is assigned a

priority. After exchanging BPDUs, the switch with the lowest priority value becomes

the root bridge. Specify the bridge priority value for the Common and Internal

CST Regional Root Priority and base MAC address of the CST regional root.

CST Path Cost Path cost to the CST tree regional root.

Table 37. STP configuration status (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual167

Spanning Tree (CST). The valid range is 0–61440. The bridge priority is a multiple of

4096. If you specify a priority that is not a multiple of 4096, the priority is automatically

set to the next lowest priority that is a multiple of 4096. For example, if you set the

priority to any value between 0 and 4095, the switch automatically sets the value to 0.

The default value is 32768.

• Bridge Max Age (secs). The bridge maximum age time for the Common and Internal

Spanning Tree (CST), which indicates the time in seconds a bridge must wait before

implementing a topological change. The valid range is 6–40, and the value must be

less than or equal to (2 * Bridge Forward Delay) – 1 and greater than or equal to 2 *

(Bridge Hello Time +1). The default value is 20.

• Bridge Hello Time (secs). The bridge hello time for the Common and Internal

Spanning Tree (CST), which indicates the time in seconds a root bridge must wait

between configuration messages. The value is fixed at 2 seconds. The value must be

less than or equal to (Bridge Max Age / 2) – 1. The default hello time value is 2.

• Bridge Forward Delay (secs). The bridge forward delay time, which indicates the

time in seconds a bridge must remains in a listening and learning state before

forwarding packets. The value must be greater or equal to (Bridge Max Age / 2) + 1.

The time range is from 4 seconds to 30 seconds. The default value is 15 seconds.

• Spanning Tree Maximum Hops. The maximum number of bridge hops the

information for a particular CST instance can travel before being discarded. The valid

range is 6–40. The default is 20 hops.

7. Click the Apply button.

Your settings are saved.

The following table describes the MSTP Status information that is displayed.

Table 38. STP advanced CST configuration, MSTP status

Field Description

MST ID Table consisting of the MST instances (including the CST) and the

corresponding VLAN IDs associated with each of them.

VID ID Table consisting of the VLAN IDs and the corresponding FID

associated with each of them.

FID ID Table consisting of the FIDs and the corresponding VLAN IDs

associated with each of them.

Configure the CST port settings

You can configure a common spanning tree (CST) and internal spanning tree on a specific

port on the switch.

A port can become diagnostically disabled (D-Disable) when DOT1S experiences a severe

error condition. The most common cause is when the DOT1S software experiences BPDU

flooding. The flooding criteria are such that DOT1S receives more than 15 BPDUs in a

3-second interval. The other causes for DOT1S D-Disable are extremely rare.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual168

To configure CST port settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > STP > Advanced > CST Port Configuration.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8. From the STP Status menu, select the option to enable or disable the spanning tree

administrative mode associated with the port or port channel.

The possible values are Enable and Disable. The default value is Enable.

9. From the Fast Link menu, select whether the specified port is an edge port within the CST.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual169

The possible values are Enable and Disable. The default value is Disable.

10. From the BPDU Forwarding menu, configure BPDU forwarding.

The possible values are Enable and Disable. The default value is Disable. When BPDU

forwarding is enabled, the switch forwards the BPDU traffic arriving on this port when

STP is disabled on this port.

11. From the Auto Edge menu, specify if the port is allowed to become an edge port if it does

not detect BPDUs for some duration.

The possible values are Enable and Disable. The default value is Enable.

12. In the Path Cost field, set the path cost to a new value for the specified port in the common

and internal spanning tree.

Specify a value in the range of 0 to 200000000. The default is 0. When the path cost is

set to 0, the value is updated with the external path cost from a received STP packet.

13. In the Priority field, specify the priority for a particular port within the CST.

The port priority is set in multiples of 16. For example if you attempt to set the priority to

any value between 0 and 15, it is set to 0. If you try to set it to any value between 16 and

(2*16 – 1), it is set to 16, and so on. The range is 0 to 240. The default value is 128.

14. In the External Port Path Cost field, set the external path cost to a new value for the

specified port in the spanning tree.

The value range is 0 to 200000000. The default is 0.

15. Click the Apply button.

Your settings are saved.

16. To refresh the page with the latest information about the switch, click the Update button.

The following table describes the nonconfigurable information displayed on the page.

Table 39. CST port configuration

Field Description

Port State The forwarding state of this port. The default is Disabled.

Port ID The port identifier for the specified port within the CST. It is made up

from the port priority and the interface number of the port.

Hello T imer The value of the parameter for the CST. The default is 2 seconds.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual170

View the CST port status

You can display the common spanning tree (CST) and internal spanning tree for a specific

port on the switch.

To view the CST port status:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > STP > Advanced > CST Port Status.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. To refresh the page with the latest information about the switch, click the Update button.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual171

The following table describes the CST Status information displayed on the page.

Table 40. CST port status

Field Description

Interface Identify the physical or port channel interfaces associated with VLANs

associated with the CST.

Port Role Each MST bridge port that is enabled is assigned a port role for each

spanning tree. The port role is one of the following values: Root Port,

Designated Port, Alternate Port, Backup Port, Master Port, or Disabled

Port.

Designated Root Root bridge for the CST. It is made up using the bridge priority and the base

MAC address of the bridge.

Designated Cost Path cost offered to the LAN by the designated port.

Designated Bridge Bridge identifier of the bridge with the designated port. It is made up using

the bridge priority and the base MAC address of the bridge.

Designated Port Port identifier on the designated bridge that offers the lowest cost to the

LAN. It is made up from the port priority and the interface number of the

port.

Topology Change Acknowledge Identifies whether the topology change acknowledgement flag is set for the

next BPDU to be transmitted for this port. It is either True or False.

Edge port Indicates whether the port is enabled as an edge port. It is either Enabled

or Disabled.

Point-to-point MAC Derived value of the point-to-point status.

CST Regional Root Bridge identifier of the CST regional root. It is made up using the bridge

priority and the base MAC address of the bridge.

CST Path Cost Path cost to the CST regional root.

Port Forwarding State The forwarding state of this port.

View Rapid STP Information

You can view information about the Rapid Spanning Tree (RSTP) port status.

To view information about RSTP:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual172

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > STP > Advanced > RSTP.

The following table describes the Rapid STP Status information displayed on the page.

Table 41. Rapid STP status information

Field Description

Interface The physical or port channel interfaces associated with VLANs associated with the CST.

Role Each MST bridge port that is enabled is assigned a port role for each spanning tree. The port

role is one of the following: Root Port, Designated Port, Alternate Port, Backup Port, Master

Port, or Disabled Port.

Mode Specifies the spanning tree operation mode. Different modes are STP, RSTP, and MSTP.

Fast Link Indicates whether the port is enabled as an edge port.

Status The forwarding state of this port.

Manage the MST settings

You can configure a multiple spanning tree (MST) on the switch.

Configure an MST instance

To configure an MST instance:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > STP > Advanced > MST Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual173

6. Configure the MST values:

• MST ID. Specify the ID of the MST to create. The valid values for this are 1 to 4094.

This is visible only when the select option of the MST ID select box is selected.

• Priority. The bridge priority value for the MST. When switches or bridges are running

STP, each is assigned a priority. After exchanging BPDUs, the switch with the lowest

priority value becomes the root bridge. The bridge priority is a multiple of 4096. If you

specify a priority that is not a multiple of 4096, the priority is automatically set to the

next lowest priority that is a multiple of 4096. For example, if you set the priority to any

value between 0 and 4095, the switch automatically sets the value to 0. The default

value is 32768. The valid range is 0–61440.

• VLAN Id. The menu includes all VLANs that are configured on the switch. You can

select VLANs that must be associated with the MST instance or clear VLANs that are

already associated with the MST instance.

7. Click the Add button.

The MST is added.

For each configured instance, the information described in the following table displays on the

page.

Table 42. MST configuration

Field Description

Bridge Identifier The bridge identifier for the selected MST instance. It is made up using the bridge

priority and the base MAC address of the bridge.

Last TCN The time in day:hour:minute:second format since the topology of the selected

MST instance last changed.

Topology Change Count Number of times that the topology changed for the selected MST instance.

Topology Change The value of the topology change parameter for the switch indicating if a topology

change is in progress on any port assigned to the selected MST instance. It is

either True or False.

Designated Root The bridge identifier of the root bridge. It is made up from the bridge priority and

the base MAC address of the bridge

Root Path Cost Path cost to the designated root for this MST instance.

Root Port Port to access the designated root for this MST instance.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual174

Modify an MST instance

To modify an MST instance:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > STP > Advanced > MST Configuration.

The MST Configuration page displays.

6. Select the check box next to the instance.

You can select multiple check boxes to apply the same setting to all selected ports.

7. Update the values.

8. Click the Apply button.

Your settings are saved.

Delete an MST instance

To delete an MST instance:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual175

5. Select Switching > STP > Advanced > MST Configuration.

The MST Configuration page displays.

6. Select the check box for the instance.

7. Click the Delete button.

The MST instance is removed.

Configure and view the port settings for an MST instance

You can configure and display the Multiple Spanning Tree (MST) settings on a specific port

on the switch.

A port can become diagnostically disabled (D-Disable) when DOT1S experiences a severe

error condition. The most common cause is when the DOT1S software experiences BPDU

flooding. The flooding criteria is such that DOT1S receives more than 15 BPDUs in a

3-second interval. The other causes for DOT1S D-Disable are extremely rare.

To configure and view the port settings for an MST instance:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > STP > Advanced > MST Port Configuration.

The MST Port Configuration page displays.

Note: If no MST instances were configured on the switch, the page displays

a “No MSTs Available” message.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

•LAG. Only LAGs are displayed.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual176

• All. Both physical interfaces and LAGs are displayed.

7. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8. Configure the MST values for the selected interfaces:

• Port Priority. The priority for a particular port within the selected MST instance. The

port priority is set in multiples of 16. If you specify a value that is not a multiple of 16,

the priority is set to the priority is automatically set to the next lowest priority that is a

multiple of 16. For example, if you set a value between 0 and 15, the priority is set to

0. If you specify a number between 16 and 31, the priority is set to 16. Specify a value

in the range of 0–240.

• Port Path Cost. Set the path cost to a new value for the specified port in the selected

MST instance. Specify a value in the range of 0–200000000.

9. Click the Apply button.

Your settings are saved.

The following table describes the read-only MST port configuration information displayed on

the Spanning Tree CST Configuration page.

Table 43. MST port status information

Field Description

Auto-calculated Port Path

Cost Indicates whether the path cost is automatically calculated (Enabled) or not

(Disabled). Path cost is calculated based on the link speed of the port if the

configured value for Port Path Cost is zero.

Port ID The port identifier for the specified port within the selected MST instance. It is

made up from the port priority and the interface number of the port.

Port Up Time Since Counters

Last Cleared The time since the counters were last cleared, displayed in days, hours,

minutes, and seconds.

Port Mode The Spanning T ree Protocol administrative mode that is associated with the port

or port channel. The possible values are Enable and Disable.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual177

View the STP statistics

You can view information about the number and type of bridge protocol data units (BPDUs)

transmitted and received on each port.

To view the spanning tree statistics:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

Port Forwarding State Indicates the current STP state of a port. If enabled, the port state determines

what forwarding action is taken on traffic. Possible port states are as follows:

• Disabled. STP is currently disabled on the port. The port forwards traffic

while learning MAC addresses.

• Blocking. The port is currently blocked and cannot be used to forward

traffic or learn MAC addresses.

• Listening. The port is currently in the listening mode. The port cannot

forward traffic nor can it learn MAC addresses.

• Learning. The port is currently in the learning mode. The port cannot

forward traffic. However, it can learn new MAC addresses.

• Forwarding. The port is currently in the forwarding mode. The port can

forward traffic and learn new MAC addresses

Port Role Each MST bridge port that is enabled is assigned a port role for each spanning

tree. The port role is one of the following: Root Port, Designated Port, Alternate

Port, Backup Port, Master Port, or Disabled Port.

Designated Root The root bridge for the selected MST instance. It is made up using the bridge

priority and the base MAC address of the bridge.

Designated Cost The cost of the port participating in the STP topology. Ports with a lower cost are

less likely to be blocked if STP detects loops.

Designated Bridge The bridge identifier of the bridge with the designated port. It is made up using

the bridge priority and the base MAC address of the bridge.

Designated Port The port identifier on the designated bridge that offers the lowest cost to the

LAN. It is made up from the port priority and the interface number of the port.

Table 43. MST port status information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual178

The default password is password.

The System Information page displays.

5. Select Switching > STP > Advanced > STP Statistics.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. To refresh the page with the latest information about the switch, click the Update button.

The following table describes the information available about the STP Statistics page.

Table 44. STP Statistics

Field Description

Interface Selects one of the physical or port channel interfaces of the switch.

STP BPDUs Received Number of STP BPDUs received at the selected port.

STP BPDUs Transmitted Number of STP BPDUs transmitted from the selected port.

RSTP BPDUs Received Number of RSTP BPDUs received at the selected port.

RSTP BPDUs Transmitted Number of RSTP BPDUs transmitted from the selected port.

MSTP BPDUs Received Number of MSTP BPDUs received at the selected port.

MSTP BPDUs Transmitted Number of MSTP BPDUs transmitted from the selected port.

Configure multicast

Multicast IP traffic is traf fic that is destined to a host group. Host groups for IPv4 multicast are

identified by class D addresses, which range from 224.0.0.0 to 239.255.255.255. Host

groups for IPv6 multicast are identified by the prefix ff00::/8.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual179

View, search, or clear the MFDB table

The Multicast Forwarding Database (MFDB) holds the port membership information for all

active multicast forwarding address entries. The key for an entry consists of a VLAN ID and

MAC address pair. Entries can contain data for more than one protocol.

To view, search, or clear the MFDB table:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > Multicast > MFDB > MFDB Table.

6. In the Search by MAC Address field, enter a MAC address.

Enter six two-digit hexadecimal numbers separated by colons, for example

00:01:23:43:45:67.

7. Click the Go button.

If the address exists, the entry is displayed. An exact match is required.

Table 45. MFDB table information

Field Description

MAC Address The multicast MAC address for which you requested data.

VLAN ID The VLAN ID to which the multicast MAC address is related.

Type The type of the entry . Static entries are those that are configured by the end

user. Dynamic entries are added to the table as a result of a learning

process or protocol.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual180

View the MFDB statistics

To view the MFDB statistics:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > Multicast > MFDB > MFDB Statistics.

Component The component that is responsible for this entry in the Multicast Forwarding

Database. Possible values are IGMP snooping, GMRP, Static Filtering and

MLD snooping.

Description The text description of this multicast table entry. Possible values are

Management Configured, Network Configured, and Network Assisted.

Forwarding Interfaces The resultant forwarding list is derived from combining all the forwarding

interfaces and removing the interfaces that are listed as the static filtering

interfaces.

Table 45. MFDB table information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual181

The following table describes the MFDB Statistics fields.

Table 46. MFDB Statistics information

Field Description

Max MFDB Table Entries The maximum number of entries that the Multicast Forwarding Database

table can hold.

Most MFDB Entries Since Last

Reset The largest number of entries that were present in the Multicast Forwarding

Database table since last reset. This value is also known as the MFDB

high-water mark.

Current Entries The current number of entries in the Multicast Forwarding Database table.

Configure the auto-video multicast settings

You can configure the auto-video multicast settings.

To configure auto-video multicast settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> Multicast > Auto-Video.

The Auto-Video Configuration page displays.

6. Select one of the following radio buttons:

•Select the Disable radio button to globally disable Auto-Video administrative mode

for the switch.

•Select the Enable radio button to globally enable Auto-Video administrative mode for

the switch.

The Auto-Video VLAN field shows the number of autoconfigured IGMP snooping VLANs.

7. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual182

Manage IGMP snooping

Internet Group Management Protocol (IGMP) snooping is a feature that allows a switch to

forward multicast traffic intelligently on the switch. Multicast IP traffic is traf fic that is destined

to a host group. Host groups are identified by class D IP addresses, which range from

224.0.0.0 to 239.255.255.255. Based on the IGMP query and report messages, the switch

forwards traffic only to the ports that request the multicast traffic. This prevents the switch

from broadcasting the traffic to all ports and possibly affecting network performance.

A traditional Ethernet network can be separated into different network segments to prevent

placing too many devices onto the same shared media. Bridges and switches connect these

segments. When a packet with a broadcast or multicast destination address is received, the

switch forwards a copy to each of the remaining network segments in accordance with the

IEEE MAC Bridge standard. Eventually, the packet is made accessible to all nodes

connected to the network.

This approach works well for broadcast packets that are intended to be seen or processed by

all connected nodes. In the case of multicast packets, however, this approach could lead to

less efficient use of network bandwidth, particularly when the packet is intended for only a

small number of nodes. Packets are flooded into network segments where no node is

receptive to the packet. While nodes rarely incur any processing overhead to filter packets

addressed to unrequested group addresses, they cannot transmit new packets onto the

shared media for the period of time that the multicast packet is flooded. The problem of

wasting bandwidth is even worse when the LAN segment is not shared, for example in

full-duplex links.

Allowing switches to snoop IGMP packets is a creative effort to solve this problem. The

switch uses the information in the IGMP packets as they are being forwarded throughout the

network to determine which segments receive packets directed to the group address.

Configure IGMP snooping

You can configure the settings for IGMP snooping, which is used to build forwarding lists for

multicast traffic.

To configure IGMP snooping:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual183

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> Multicast > IGMP Snooping > Configuration.

6. Select the IGMP Snooping Status Enable or Disable radio button.

This specifies the administrative mode for IGMP snooping for the switch. The default is

Disable.

7. Select the Validate IGMP IP header Enable or Disable radio button.

When IGMP IP header validation is enabled, any IGMP IP header must include the

Router Alert, ToS, and TTL information. Otherwise, the IGMP packet is discarded. The

default value is Enable.

8. Click the Apply button.

Your settings are saved.

9. To refresh the page with the latest information about the switch, click the Update button.

The following table displays information about the global IGMP snooping status and statistics

on the page.

Table 47. IGMP Snooping Configuration information

Field Description

Multicast Control Frame Count The number of multicast control frames that are processed by the CPU.

Interfaces Enabled for IGMP

Snooping The interfaces that are enabled for IGMP snooping.

VLAN IDs Enabled For IGMP

Snooping The IDs of the VLANs that are enabled for IGMP snooping.

VLAN IDs Enabled For IGMP

Snooping Querier The IDs of the VLANs that are enabled for IGMP snooping querier.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual184

Configure IGMP snooping for interfaces

To configure IGMP snooping for interfaces:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> Multicast > IGMP Snooping > Interface Configuration.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8. From the Admin Mode menu, select Disable or Enable.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual185

This specifies the interface mode for the selected interface for IGMP snooping for the

switch. The default is Disable.

9. In the Host Timeout field, specify the time that the switch must wait for a report for a

particular group on a particular interface before it deletes that interface from the group.

Enter a value between 1 and 3600 seconds. The default is 260 seconds.

10. In the Max Response Time field, specify the time that the switch must wait after sending a

query on an interface because it did not receive a report for a particular group on that

interface.

Enter a value greater or equal to 1 and less than the group membership interval in

seconds. The default is 10 seconds. The configured value must be less than the group

membership interval.

11. In the MRouter Timeout field, specify the time that the switch must wait to receive a query

on an interface before removing it from the list of interfaces with multicast routers attached.

Enter a value between 0 and 3600 seconds. The default is 0 seconds. A value of zero

indicates an infinite time-out, that is, no expiration.

12. From the Fast Leave Mode menu, select whether fast leave mode is enabled.

The option are Enable and Disable. The default is Disable.

13. Click the Apply button.

Your settings are saved.

View, search, or clear the IGMP snooping table

You can view and clear all entries in the Multicast Forwarding Database that were created for

IGMP snooping.

To view, search, or clear the IGMP snooping table:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> Multicast > IGMP Snooping > IGMP Snooping Table.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual186

The IGMP Snooping Table page displays.

6. In the Search By MAC Address field, specify the MAC address whose MFDB table entry

you want to view.

Enter six two-digit hexadecimal numbers separated by colons, for example

00:01:23:43:45:67.

7. Click the Go button.

If the address exists, the entry is displayed. An exact match is required.

The following table describes the information in the IGMP snooping table.

Table 48. IGMP Snooping Table information

Field Description

MAC Address The multicast MAC address for which the switch holds forwarding and/or filtering

information. The format is six two-digit hexadecimal numbers that are separated

by colons, for example, 01:00:5e:45:67:89.

VLAN ID The VLAN ID for which the switch holds forwarding and filtering information.

Type The type of the entry. Static entries are those that are configured by the end

user. Dynamic entries are added to the table as a result of a learning process or

protocol.

Description The text description of this multicast table entry. Possible values are

Management Configured, Network Configured, and Network Assisted.

Interface The interfaces that are designated for forwarding (Fwd) and filtering (Flt) for the

associated address.

Configure IGMP snooping for VLANs

To configure IGMP snooping for VLANs:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual187

5. Select Switching> Multicast > IGMP Snooping > IGMP VLAN Configuration.

6. To enable IGMP snooping on a VLAN, in the VLAN ID field, enter the VLAN ID.

7. Configure the IGMP snooping values:

• Admin Mode. Enable or disable IGMP snooping for the specified VLAN ID. The

default is Disable.

• Fast Leave Mode. Enable or disable the IGMP snooping fast leave mode for the

specified VLAN ID. The default is Disable.

• Host Timeout. Set the value for group membership interval of IGMP snooping for the

specified VLAN ID. The valid range is Maximum Response Time + 1 to 3600

seconds.

• Maximum Response Time. Set the value for the maximum response time of IGMP

snooping for the specified VLAN ID. The valid range is 1 to Group Membership

Interval –1. This value must be greater than group membership interval value.

•MRouter Timeout. Set the value for multicast router expiry time of IGMP snooping for

the specified VLAN ID. The valid range is 0 to 3600 seconds.

• Report Suppression Mode. Enable or disable IGMP snooping report suppression

mode for the specified VLAN ID. IGMP snooping report suppression allows the

suppression of the IGMP reports sent by the multicast hosts by building a Layer 3

membership table. The results is that only the most essential reports are sent to the

IGMP routers so that the routers can continue to receive the multicast traffic.The

default is Disable.

•Querier Mode. Enable or disable the IGMP querier mode. If proxy querier mode is

disabled, then an IGMP proxy query with source IP 0.0.0.0 is not sent in response to

an IGMP leave packet. The default is Disable.

• Query Interval. Set the IGMP query interval for the specified VLAN ID. The valid

range is 1 to 1800 seconds. The default is 60 seconds.

8. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual188

Modify IGMP snooping settings for a VLAN

To modify IGMP snooping settings for a VLAN:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> Multicast > IGMP Snooping > IGMP VLAN Configuration.

The IGMP Snooping VLAN Configuration page displays.

6. Select the check box next to the VLAN ID.

7. Update the values.

8. Click the Apply button.

Your settings are saved.

Disable IGMP snooping on a VLAN and remove it from the

table

To disable IGMP snooping on a VLAN and remove it from the table:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual189

The System Information page displays.

5. Select Switching> Multicast > IGMP Snooping > IGMP VLAN Configuration.

The IGMP Snooping VLAN Configuration page displays.

6. Select the check box next to the VLAN ID.

7. Click the Delete button.

Snooping is disabled on the VLAN and the VLAN is removed from the table.

Configure one or more IGMP multicast router interfaces

You can configure an interface as the designated interface to which a multicast router is

attached. All IGMP packets snooped by the switch are forwarded to the multicast router

reachable from this interface. Configuring a multicast router interface is usually not required

because the switch automatically detects the multicast router and forwards IGMP packets

accordingly. It is required only if you want to make sure that the multicast router always

receives IGMP packets from the switch in a complex network.

To configure one or more IGMP multicast router interfaces:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> Multicast > IGMP Snooping > Multicast Router Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual190

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

•LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8. In the Multicast Router field, select Enable or Disable.

9. Click the Apply button.

Your settings are saved.

Configure an IGMP multicast router VLAN

You can configure an interface to forward only snooped IGMP packets from a specific VLAN

to the multicast router connected to the interface. This configuration is usually not required

because the switch automatically detects a multicast router and forwards the IGMP packets

accordingly. This configuration is required only in a complex network if you want to make sure

that the multicast router always receives IGMP packets from the switch.

To configure an IGMP multicast router VLAN:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> Multicast > IGMP Snooping > Multicast Router VLAN

Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual191

6. From the Interface menu, select the interface.

7. In the VLAN ID field, enter the VLAN ID.

8. From the Multicast Router menu, select Enable or Disable.

9. Click the Apply button.

Your settings are saved.

IGMP snooping querier overview

IGMP snooping requires that one central switch or router periodically query all end-devices

on the network to announce their multicast memberships. This central device is the IGMP

querier. The IGMP query responses, known as IGMP reports, keep the switch updated with

the current multicast group membership on a port-by-port basis. If the switch does not

receive updated membership information in a timely fashion, it stops forwarding multicasts to

the port where the end device is located.

You can configure and display information about IGMP snooping queriers on the network

and, separately, on VLANs.

Configure an IGMP snooping querier

You can configure the settings for an IGMP snooping querier.

To configure the settings for an IGMP snooping querier:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual192

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> Multicast > IGMP Snooping Querier > Querier Configuration.

6. Configure the following settings:

• Querier Admin Mode. Enable or disable IGMP snooping for the switch. The default is

Disable.

• Snooping Querier IP Address. Enter the snooping querier IP address to be used as

the source address in periodic IGMP queries. This address is used when no address

is configured on the VLAN on which a query is being sent.

• IGMP Version. Specify the IGMP protocol version used in periodic IGMP queries.

The range is 1 to 2. The default value is 2.

• Query Interval(secs). Specify the time interval in seconds between periodic queries

sent by the snooping querier. The query interval must be a value in the range of 1 and

1800. The default value is 60.

• Querier Expiry Interval(secs). Specify the time interval in seconds after which the

last querier information is removed. The querier expiry Interval must be a value in the

range of 60 and 300. The default value is 125.

7. Click the Apply button.

Your settings are saved.

Configure an IGMP snooping querier for a VLAN

You can configure IGMP queriers for use with VLANs on the network.

To configure IGMP snooping for a VLAN:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual193

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> Multicast > IGMP Snooping Querier > Querier VLAN Configuration.

6. From the VLAN ID menu, select New Entry.

7. Configure the following settings:

• VLAN ID. The VLAN ID for which the IGMP snooping querier is to be enabled.

• Querier Election Participate Mode. Enable or disable querier this mode:

- Disable. Upon seeing another querier of the same version in the VLAN, the

snooping querier moves to the non-querier state.

- Enable. The snooping querier participates in querier election, in which the lowest

IP address operates as the querier in that VLAN. The other querier moves to

non-querier state.

•Snooping Querier VLAN Address. Specify the snooping querier IP address to be

used as the source address in periodic IGMP queries sent on the specified VLAN.

8. Click the Apply button.

Your settings are saved.

Display the status of the IGMP snooping querier for VLANs

To display the status of the IGMP snooping querier VLANs:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual194

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> Multicast > IGMP Snooping Querier > Querier VLAN Status.

The following table describes the nonconfigurable information displayed on the page.

Table 49. Querier VLAN Status information

Field Description

VLAN ID The VLAN ID on which IGMP snooping querier is administratively enabled

and the VLAN exists in the VLAN database.

Operational State The operational state of the IGMP snooping querier on a VLAN. It can be in

any of the following states:

Operational Version The operational IGMP protocol version of the querier.

Last Querier Address The IP address of the last querier from which a query was snooped on the

VLAN.

Last Querier Version The IGMP protocol version of the last querier from which a query was

snooped on the VLAN.

Operational Max Response Time The maximum response time to be used in the queries that are sent by the

snooping querier.

• Querier. The snooping switch is the querier in the VLAN. The snooping

switch sends out periodic queries with a time interval equal to the

configured querier query interval. If the snooping switch finds a better

querier in the VLAN, it moves to non-querier mode.

• Non-Querier. The snooping switch is in non-querier mode in the VLAN.

If the querier expiry interval timer expires, the snooping switch moves

into querier mode.

• Disabled. The snooping querier is not operational on the VLAN. The

snooping querier moves to disabled mode when IGMP snooping is not

operational on the VLAN or when the querier address is not configured

or the network management address is also not configured.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual195

Manage MLD snooping

In IPv6 networks, Multicast Listener Discovery (MLD) snooping performs a similar function as

IGMP does in IPv4 networks. With MLD snooping, IPv6 multicast data is selectively

forwarded to ports that are configured to receive the data, instead of being flooded to all ports

in a VLAN. The ports are determined by snooping IPv6 multicast control packets.

A multicast listener is a device that is configured to receive IPv6 multicast packets. MLD is

used by IPv6 multicast routers to discover the presence of multicast listeners on its

directly-attached links and to discover which multicast packets are of interest to neighboring

devices.

The MLD protocol is derived from IGMP. MLD version 1 (MLDv1) is equivalent to IGMPv2,

and MLD version 2 (MLDv2) is equivalent to IGMPv3. MLD is a subprotocol of Internet

Control Message Protocol version 6 (ICMPv6), and MLD messages are a subset of ICMPv6

messages, identified in IPv6 packets by a preceding Next Header value of 58.

Enable MLD snooping

You can enable MLD snooping, which is used to build forwarding lists for multicast traffic.

To enable MLD snooping:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> Multicast > MLD Snooping > Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual196

6. Select the MLD Snooping Admin Mode Enable radio button.

By default, the Disable radio button is selected.

7. Click the Apply button.

Your settings are saved.

8. To refresh the page with the latest information about the switch, click the Update button.

The following table describes the nonconfigurable MLD Snooping Configuration fields.

Table 50. MLD Snooping Configuration information

Field Definition

Multicast Control Frame Count The number of multicast control frames that were processed by the CPU.

Interfaces Enabled for MLD

Snooping The interfaces on which MLD snooping is administratively enabled. MLD

snooping must be enabled globally and on an interface for the interface to

be able to snoop MLD packets to determine which segments must receive

multicast packets directed to the group address.

VLAN IDs Enabled For MLD

Snooping The VLANs on which MLD snooping is administratively enabled.

Configure MLD snooping for interfaces

To configure MLD snooping for interfaces:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual197

The default password is password.

The System Information page displays.

5. Select Switching> Multicast > MLD Snooping > Interface Configuration.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8. From the Admin Mode menu, select to enable or disable the interface mode for the

selected interface for MLD snooping for the switch.

The default is Disable.

9. In the Membership Interval field, specify the time that the switch must wait for a report for

a particular group on a particular interface before it deletes that interface from the group.

The valid range is from 2 to 3600 seconds. The configured value must be greater than the

maximum response time. The default is 260 seconds.

10. In the Max Response Time in seconds field, specify the time that the switch must wait

after sending a query on an interface because it did not receive a report for a particular

group on that interface.

Enter a value greater than or equal to 1 and less than the group membership interval in

seconds. The default is 10 seconds. The configured value must be less than the group

membership interval.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual198

11. In the Expiration Time field, specify the time that the switch must wait to receive a query on

an interface before removing the interface from the list of interfaces with multicast routers

attached.

Enter a value between 0 and 3600 seconds. The default is 0 seconds. A value of zero

indicates an infinite time-out, that is, no expiration.

12. From the Fast Leave menu, select to enable or disable Fast Leave on the interface.

If Fast Leave is enabled, the interface can be immediately removed from the Layer 2

forwarding table when the switch receives an MLD leave message for a multicast group

without first sending MAC-based general queries. The default is Disable.

13. Click the Apply button.

Your settings are saved.

Configure the MLD VLAN settings

To configure the MLD VLAN settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> Multicast > MLD Snooping > MLD VLAN Configuration.

6. In the VLAN ID field, specify the VLAN IDs for which MLD snooping is enabled.

7. From the Fast Leave menu, select to enable or disable the MLD snooping Fast Leave mode

for the specified VLAN ID.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual199

8. In the Membership Interval field, set the value for the group membership interval of MLD

snooping for the specified VLAN ID.

The valid range is Maximum Response Time + 1 to 3600.

9. In the Maximum Response Time field, set the value for the maximum response time of

MLD snooping for the specified VLAN ID.

The valid range is 1 to Group Membership Interval –1. This value must be less than the

group membership interval value.

10. In the Multicast Router Expiry Time field, set the value for the multicast router expiry time

of MLD snooping for the specified VLAN ID.

The valid range is 0 to 3600.

11. Click the Add button.

MLD snooping is enabled on the specified VLAN.

12. Click the Apply button.

Your settings are saved.

Modify the MLD snooping settings for a VLAN

To the modify MLD snooping settings for a VLAN:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> Multicast > MLD Snooping > MLD VLAN Configuration.

The MLD VLAN Configuration page displays.

6. Select the check box next to the VLAN ID.

7. Change the settings.

8. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual200

Remove MLD snooping from a VLAN

To remove MLD snooping from a VLAN:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> Multicast > MLD Snooping > MLD VLAN Configuration.

The MLD VLAN Configuration page displays.

6. Select the check box next to the VLAN ID.

7. Click the Delete button.

MLD snooping is removed from the VLAN.

Configure one or more MLD multicast router interfaces

To configure one or more MLD multicast router interfaces:

Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

8. Launch a web browser.

9. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

10. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

11. Select Switching> Multicast > MLD Snooping > Multicast Router Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual201

12. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

13. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

14. From the Multicast Router menu, select to enable or disable the multicast router for the

selected interfaces.

15. Click the Apply button.

Your settings are saved.

Configure an MLD multicast router VLAN

To configure an MLD multicast router VLAN:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual202

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> Multicast > MLD Snooping > Multicast Router VLAN Configuration.

6. From the Interface menu, select the interface for which you want the multicast router to be

enabled.

7. In the VLAN ID field, specify the VLAN ID.

8. From the Multicast Router menu, select to enable or disable the multicast router for the

VLAN ID.

9. Click the Apply button.

Your settings are saved.

Configure an MLD snooping querier

You can configure the settings for an MLD snooping querier.

To configure an MLD snooping querier:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual203

5. Select Switching> Multicast > MLD Snooping > Querier Configuration.

6. Configure the following settings:

• Querier Admin Mode. Enable or disable MLD snooping for the switch. The default is

Disable.

• Querier Address. Enter an IP address. This specifies the snooping querier address

to be used as the source address in periodic MLD queries. This address is used when

no address is configured on the VLAN on which a query is being sent. The supported

IPv6 formats are x:x:x:x:x:x:x:x and x::x.

• MLD Version. Specify the MLD protocol version used in periodic MLD queries.

• Query Interval(secs). Specify the interval in seconds between periodic queries sent

by the snooping querier. The query interval must be a value in the range of 1 to 1800.

The default value is 60.

•Querier Expiry Interval(secs). Specify the interval in seconds after which the last

querier information is removed. The querier expiry interval must be a value in the

range of 60 to 300. The default value is 60.

7. Click the Apply button.

Your settings are saved.

The page displays VLAN IDs enabled for the MLD snooping querier.

Configure the MLD snooping querier VLAN settings

To configure the MLD snooping querier VLAN settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual204

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching> Multicast > MLD Snooping > Querier VLAN Configuration.

6. In the VLAN ID field, specify the VLAN ID on which the MLD snooping querier is

administratively enabled and for which a VLAN exists in the VLAN database.

7. From the Querier Election Participate Mode menu, select to enable or disable the querier

participation election mode for MLD snooping.

When this mode is disabled, on detecting another querier of same version in the VLAN,

the snooping querier moves to a non-querier state. When this mode is enabled, the

snooping querier participates in querier election where the lowest IP address wins the

querier election and operates as the querier in that VLAN. The other querier moves to

non-querier state.

8. In the Querier VLAN Address field, specify the snooping querier address to be used as the

source address in periodic MLD queries sent on the specified VLAN.

9. Click the Apply button.

Your settings are saved.

The following table describes the nonconfigurable information displayed on the page.

Table 51. MLD Snooping Querier VLAN Configuration information

Field Description

Operational State The operational state of the MLD snooping querier on a VLAN. It can be in any of the

following states:

• Querier. Snooping switch is the querier in the VLAN. The snooping switch sends

out periodic queries with a time interval equal to the configured querier query

interval. If the snooping switch sees a better querier in the VLAN, it moves to

non-querier mode.

• Non-Querier. Snooping switch is in non-querier mode in the VLAN. If the querier

expiry interval timer is expired, the snooping switch moves into querier mode.

• Disabled. Snooping querier is not operational on the VLAN. The snooping querier

moves to disabled mode when MLD snooping is not operational on the VLAN or

when the querier address is not configured or the network management address is

also not configured.

Operational Version The operational MLD protocol version of the querier.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual205

Configure multicast VLAN registration

IGMP snooping helps limit multicast traffic when member ports are in the same VLAN.

However, when ports belong to different VLANs, a copy of the multicast stream is sent to

each VLAN with member ports in the multicast group. Multicast VLAN registration (MVR)

eliminates the need to duplicate the multicast traffic when multicast group member ports

belong to different VLANs.

MVR uses a dedicated multicast VLAN to forward multicast traffic over the L2 network. Only

one multicast source VLAN (MVLAN can be configured per switch, and it is used only for

certain multicast traffic, such as traffic from an IPTV application, to avoid duplication of

multicast streams for clients in different VLANs. Clients can dynamically join or leave the

multicast VLAN without interfering with their membership in other VLANs.

MVR, like IGMP snooping, allows a Layer 2 switch to listen to IGMP messages to learn about

multicast group membership.

You can configure basic, advanced, group, interface, or group membership settings.

Configure the global MVR settings

To configure the global MVR settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

Last Querier Address The IP address of the last querier from which a query was snooped on the VLAN.

Last Querier Version The MLD protocol version of the last querier from which a query was snooped on the

VLAN.

Operational Max

Response T ime The maximum response time to be used in the queries that are sent by the snooping

querier.

Table 51. MLD Snooping Querier VLAN Configuration information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual206

The System Information page displays.

5. Select Switching > MVR > Basic > MVR Configuration.

6. From the MVR Running menu, select Enable or Disable.

The default is Disable.

7. In the MVR Multicast Vlan field, specify the VLAN on which MVR multicast data is

received.

All source ports belong to this VLAN. The value can be set in a range of 1 to 4093. The

default value is 1.

8. In the MVR Global Query Response Time field, set the maximum time that the switch must

wait for an IGMP group membership report before removing the port from the multicast

group membership.

This time applies only to receiver-port leave processing. When an IGMP query is sent

from a receiver port, the switch waits for the default or configured MVR query time for an

IGMP group membership report before removing the port from the multicast group

membership. The value is equal to tenths of a second. The range is from 1 to 100 tenths.

The default is 5 tenths or one-half.

9. From the MVR Mode menu, specify the MVR mode of operation.

The options are compatible and dynamic. The default is compatible.

10. Click the Apply button.

Your settings are saved.

11. To refresh the page with the latest information about the switch, click the Update button.

The following table describes the nonconfigurable information displayed on the page.

Table 52. MVR Configuration information

Field Definition

MVR Max Multicast Groups The maximum number of multicast groups that MVR supports.

MVR Current Multicast Groups The number of MVR groups allocated.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual207

Configure an MVR group

To configure an MVR group:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > MVR > Advanced > MVR Group Configuration.

6. In the MVR Group IP field, specify the IP address for the new MVR group.

7. In the Count field, specify the number of contiguous MVR groups.

This number helps you to create multiple MVR groups through a single click of the Add

button. If the field is empty, then clicking the button creates only one new group. The field

is displayed as empty for each particular group. The range is from 1 to 256.

8. Click the Add button.

The MVR group is added.

The following table describes the nonconfigurable information displayed on the page.

Table 53. MVR Group Configuration

Field Definition

Status The status of the specific MVR group.

Members The list of ports that participate in the specific MVR group.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual208

Configure MVR group membership

To configure MVR group membership:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > MVR > Advanced > MVR Group Membership.

6. From the Group IP menu, select the IP multicast address of the MVR group.

7. In the Ports table, click each port that you want to make a member of the MVR group.

A selected port is shown by a check mark.

8. Click the Apply button.

Your settings are saved.

Configure the MVR interface settings

To configure the MVR interface setting:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual209

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > MVR > Advanced > MVR Interface Configuration.

6. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

7. From the Admin Mode menu, specify whether MVR is enabled by selecting Enable or

Disable.

The default is Disable.

8. From the Type menu, specify whether the port is an MVR receiver or an MVR source by

selecting receiver or a source.

The default port type is none.

9. From the Immediate Leave menu, specify whether the Immediate Leave feature is enabled

by selecting Enable or Disable.

The default is Disable.

10. Click the Apply button.

Your settings are saved.

11. To refresh the page with the latest information about the switch, click the Update button.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual210

View the MVR statistics

To view the MVR statistics:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > MVR > Advanced > MVR Statistics.

6. To refresh the page with the latest information about the switch, click the Update button.

The following table describes the nonconfigurable information displayed on the page.

Table 54. MVR Statistics information

Field Definition

IGMP Query Received The number of received IGMP queries.

IGMP Report V1 Received The number of received IGMP V1 reports.

IGMP Report V2 Received The number of received IGMP V2 reports.

IGMP Leave Received The number of received IGMP leaves.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual211

View, search, and manage the MAC

address table

You can view or configure the MAC address table. This table contains information about

unicast entries for which the switch holds forwarding or filtering information. This information

lets the transparent bridging function determine how an incoming frame must be propagated.

If you clear the MAC address entries in the MAC address table, only the dynamic entries are

removed.

View, search, or clear the MAC address table

To view, search, or clear the MAC address table:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > Address Table > Basic > Address Table.

IGMP Query Transmitted The number of transmitted IGMP queries.

IGMP Report V1 Transmitted The number of transmitted IGMP V1 reports.

IGMP Report V2 Transmitted The number of transmitted IGMP V2 reports.

IGMP Leave Transmitted The number of transmitted IGMP leaves.

IGMP Packet Receive Failures The number of IGMP packet receive failures.

IGMP Packet Transmit Failures The number of IGMP packet transmit failures.

Table 54. MVR Statistics information (continued)

Field Definition

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual212

6. Use the Search menu and field to search for a MAC address, VLAN ID, or interface number:

• Search by MAC Address. From the Search menu, select MAC Address, and enter

the 6-byte hexadecimal MAC address in two-digit groups separated by colons, for

example, 01:23:45:67:89:AB. Then click the Go button.

If the address exists, that entry is displayed as the first entry followed by the

remaining (higher) MAC addresses. An exact match is required.

• Search VLAN ID. From the Search menu, select VLAN ID, and enter the VLAN ID, for

example, 100. Then click the Go button.

• Search Interface. From the Search menu, select Interface, and enter the interface ID

using the respective interface naming convention (for example, g1 or l1). Then click the

Go button.

The following table describes the nonconfigurable information displayed on the page.

Table 55. MAC Address Table information

Field Description

Total MAC Address The number of total MAC addresses learned or configured.

MAC Address The unicast MAC address for which the switch holds forwarding and/or

filtering information. The format is a 6-byte MAC address that is separated

by colons, for example 01:23:45:67:89:AB.

VLAN ID The VLAN ID associated with the MAC address.

Interface The interface upon which this address was learned.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual213

Set the dynamic address aging interval

You can set the address aging interval for the forwarding database. This is the time-out

period in seconds for aging out dynamically learned forwarding information.

To set the address aging interval:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > Address Table > Advanced > Dynamic Addresses.

6. In the Address Aging T imeout (seconds) field, specify the time-out period in seconds for

aging out dynamically learned forwarding information.

802.1D-1990 recommends a default of 300 seconds. The value can be any number

between 10 and 1000000 seconds. The default is 300.

7. Click the Apply button.

Your settings are saved.

Status The status of this entry. The meanings of the values are as follows:

• Static. The value of the corresponding instance was added by the

system or a user and cannot be relearned.

• Learned. The value of the corresponding instance was learned, and is

being used.

• Management. The value of the corresponding instance is also the

value of an existing instance of dot1dStaticAddress.

Table 55. MAC Address Table information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual214

Add a static MAC address to the MAC address table

To add a static MAC address to the MAC address table:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > Address Table > Advanced > Static MAC Address.

6. From the Interface menu, select the interface.

7. In the Static MAC Address field, enter the MAC address.

8. From the VLAN ID menu, select the VLAN ID that must be associated with the MAC

address.

9. Click the Add button.

The static MAC address is added to the switch.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual215

Configure Layer 2 loop protection

Loops inside a network are costly because they consume resources and reduce the

performance of the network. Detecting loops manually can be cumbersome.

The switch can automatically identify loops in the network. You can enable loop protection

per port or globally.

If loop protection is enabled, the switch sends predefined PDU packets to a Layer 2 multicast

destination address (09:00:09:09:13:A6) on all ports for which the feature is enabled. You

can selectively disable PDU packet transmission for loop protection on specific ports even

while port loop protection is enabled. If the switch receives a packet with the previously

mentioned multicast destination address, the source MAC address in the packet is compared

with the MAC address of the switch. If the MAC address does not match, the packet is

forwarded to all ports that are members of the same VLAN, just like any other multicast

packet. The packet is not forwarded to the port from which it was received.

If the source MAC address matches the MAC address of the switch, the switch can perform

one of the following actions, depending on how you configure the action:

•The port is shut down.

•A log message is generated. (If a syslog server is configured, the log message can be

sent to the syslog server.)

•The port is shut down and a log message is generated.

If loop protection is disabled, the multicast packet is silently dropped.

Loop protection is not intended for ports that serve as uplinks between spanning tree–aware

switches. It is intended for unmanaged switches that drop spanning tree BPDUs. Loop

protection detects physical and logical loops between Ethernet ports on a device. You must

enable loop protection globally before you can enable and configure it at the interface level.

Loop protection is supported on physical interfaces and static LAG interfaces, but not on

dynamic LAG interfaces.

Configure global Layer 2 loop protection

To configure L2 loop protection globally:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual216

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > L2 Loop Protection > L2 Loop Protection Configuration.

6. To enable or disable loop protection feature, select the Admin Mode Enable or Disable

radio button.

By default, the Disable radio button is selected.

7. From the Transmit Interval menu, select the time in seconds between transmission of loop

packets.

The default transmit interval is 5 seconds.

8. From the Max PDU Receive menu, select the maximum number of packets to be received

before an action is taken.

The default is 1.

9. In the Disable Timer field, enter the time in seconds after which a port is disabled when a

loop is detected.

The range is from 0 to 604800 seconds. The default is 0 seconds.

10. Click the Apply button.

Your settings are saved.

View and configure Layer 2 loop protection on a port

To view and configure L2 loop protection on a port:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual217

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Switching > L2 Loop Protection > L2 Loop Protection Configuration.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8. From the Keep Alive menu, select Enable or Disable to specify whether keep-alives are

enabled on an interface.

The default is Disable.

9. From the RX Action menu, select the action that occurs when the switch detects a loop on

an interface:

• Log. The switch logs a message.

• Disable. The switch disables the interface. This is the default action.

•Both. The switch both logs a message and disables the interface.

10. Click the Apply button.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Switching User Manual218

Your settings are saved.

11. Click the Clear button to clear all the statistics in the table.

12. Click the Update button to update the page to show the latest information.

The following table describes the nonconfigurable information displayed on the page.

Table 56. L2 Loop Protection Interface Information

Field Description

Loop Detected Shows whether a loop is detected on the interface. If the interface is

disabled and then reenabled, the status changes to No again.

Loop Count The number of packets that were received after the loop was detected.

Time Since Last Loop The time that elapsed since the loop was detected.

Port Status The status of the interface (Enabled, Disabled, or D-Disabled, which stands

for diagnostically disabled).

219

4Configure Routing

This chapter covers the following topics:

•Routing concepts

•Configure the routing mode

•Configure IPv6 routing

•Configure VLAN routing

•Configure router discovery for a VLAN routing interface

•Manage routes and view the routing table

•Configure Address Resolution Protocol

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual220

Routing concepts

The switch supports IP routing. When a packet enters the switch, the switch checks the

destination MAC address to determine if it matches any of the configured routing interfaces. If

it does, the switch searches the host table for a matching destination IP address. If a

matching entry is found, the packet is routed to the host. If no matching entry is found, the

switch performs a longest prefix match on the destination IP address. If a matching entry is

found, the packet is routed to the next hop. If no matching entry is found, the packet is routed

to the next hop that is specified in the default route. If no default route exists, the packet is are

dropped.

The routing table can include static entries that you added manually. The host table can

include static entries that were manually added and entries that were dynamically added

through ARP.

Configure the routing mode

For information about how to configure the routing mode and display IP routing data, see the

following sections:

•Configure the router settings on page 220

•View the IP routing statistics on page 221

Configure the router settings

You can enable routing and configure the routing settings for the switch.

The switch allows routing through any of its interfaces only after you enable routing on the

switch. Separately, you can enable routing on VLANs (see Configure VLAN routing on

page 240).

To enable routing on the switch:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual221

The default password is password.

The System Information page displays.

5. Select Routing > IP > IP Configuration.

6. Select the Routing Mode Enable radio button.

You must enable routing for the switch before you can route through any of the

interfaces. Routing is also enabled or disabled per VLAN interface. The default value is

Disable.

7. Click the Apply button.

Your settings are saved.

The following table describes the IP configuration information displayed on the page.

Table 57. Global IP status information

Field Description

Default Time to Live The default value inserted into the Time-To-Live field of the IP header of

datagrams originated by the switch, if a TTL value is not supplied by the

transport layer protocol. The default value is 64.

Maximum Next Hops The maximum number of hops supported by the switch. This is a compile-time

constant. The default value is 1.

View the IP routing statistics

You can view the IP routing statistics as specified in RFC 1213.

To view the IP routing statistics:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual222

The default password is password.

The System Information page displays.

5. Select Routing> IP > Statistics.

The following table describes the nonconfigurable information displayed on the page.

Table 58. IP Statistics information

Field Description

IpInReceives The total number of input datagrams received from interfaces, including

those received in error.

IpInHdrErrors The number of input datagrams discarded due to errors in their IP headers,

including bad checksums, version number mismatch, other format errors,

time-to-live exceeded, errors discovered in processing their IP options, and

so on.

IpInAddrErrors The number of input datagrams discarded because the IP address in their

IP header’s destination field was not a valid address to be received at this

entity. This count includes invalid addresses (for example, 0.0.0.0) and

addresses of unsupported classes (Class E). For entities that are not IP

gateways and therefore do not forward datagrams, this counter includes

datagrams discarded because the destination address was not a local

address.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual223

IpForwDatagrams The number of input datagrams for which this entity was not their final IP

destination, as a result of which an attempt was made to find a route to

forward them to that final destination. In entities that do not act as IP

gateways, this counter includes only those packets that were source-routed

through this entity, and the source-route option processing was successful.

IpInUnknownProtos The number of locally addressed datagrams received successfully but

discarded because of an unknown or unsupported protocol.

IpInDiscards The number of input IP datagrams for which no problems were encountered

to prevent their continued processing, but that were discarded (for lack of

buffer space). This counter does not include any datagrams discarded while

awaiting re-assembly.

IpInDelivers The total number of input datagrams successfully delivered to IP user

protocols (including ICMP).

IpOutRequests The total number of IP datagrams that local IP user protocols (including

ICMP) supplied to IP in requests for transmission. This counter does not

include any datagrams counted in ipForwDatagrams.

IpOutDiscards The number of output IP datagrams for which no problem was encountered

to prevent their transmission to their destination, but that were discarded for

reasons such as lack of buffer space. This counter would include

datagrams counted in ipForwDatagrams if any such packets met this

(discretionary) discard criterion.

IpOutNoRoutes The number of IP datagrams discarded because no route could be found to

transmit them to their destination. This counter includes any packets

counted in ipForwDatagrams that meet this no-route criterion. This includes

any datagrams that a host cannot route because all of its default gateways

are down.

IpReasmTimeout The maximum number of seconds for which received fragments are held

while they are awaiting reassembly at this entity.

IpReasmReqds The number of IP fragments received that were reassembled at this entity.

IpReasmOKs The number of IP datagrams successfully reassembled.

IpReasmFails The number of failures detected by the IP reassembly algorithm (for

whatever reason: timed out, errors, and so on). This is not necessarily a

count of discarded IP fragments since some algorithms can lose track of the

number of fragments by combining them as they are received.

IpFragOKs The number of IP datagrams that were fragmented at this entity.

IpFragFails The number of IP datagrams that were discarded because they needed to

be fragmented at this entity but could not be, for reasons such as their Don't

Fragment flag was set.

IpFragCreates The number of IP datagram fragments that were generated as a result of

fragmentation at this entity.

Table 58. IP Statistics information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual224

IpRoutingDiscards The number of routing entries that were discarded even though they were

valid. One possible reason for discarding such an entry could be to free up

buffer space for other routing entries.

IcmpInMsgs The total number of ICMP messages that the entity received. This counter

includes all those counted by icmpInErrors.

IcmpInErrors The number of ICMP messages that the entity received but determined as

having ICMP-specific errors (bad ICMP checksums, bad length, and so on).

IcmpInDestUnreachs The number of ICMP destination unreachable messages received.

IcmpInTimeExcds The number of ICMP time exceeded messages received.

IcmpInParmProbs The number of ICMP parameter problem messages received.

IcmpInSrcQuenchs The number of ICMP source quench messages received.

IcmpInRedirects The number of ICMP redirect messages received.

IcmpInEchos The number of ICMP echo (request) messages received.

IcmpInEchoReps The number of ICMP echo reply messages received.

IcmpInTimestamps The number of ICMP timestamp (request) messages received.

IcmpInTimestampReps The number of ICMP timestamp reply messages received.

IcmpInAddrMasks The number of ICMP address mask request messages received.

IcmpInAddrMaskReps The number of ICMP address mask reply messages received.

IcmpOutMsgs The total number of ICMP messages that this entity attempted to send. This

counter includes all those counted by icmpOutErrors.

IcmpOutErrors The number of ICMP messages that this entity did not send due to

problems discovered within ICMP such as a lack of buffers. This value does

not include errors discovered outside the ICMP layer such as the inability of

IP to route the resultant datagram. In some implementations there might be

no types of error that contribute to this counter's value.

IcmpOutDestUnreachs The number of ICMP destination unreachable messages sent.

IcmpOutTimeExcds The number of ICMP time exceeded messages sent.

IcmpOutParmProbs The number of ICMP parameter problem messages sent.

IcmpOutSrcQuenchs The number of ICMP source quench messages sent.

IcmpOutRedirects The number of ICMP redirect messages sent. For a host, this is always

zero, since hosts do not send redirects.

IcmpOutEchos The number of ICMP echo (request) messages sent.

IcmpOutEchoReps The number of ICMP echo reply messages sent.

Table 58. IP Statistics information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual225

Configure IPv6 routing

Note: IPv6 is supported on VLAN interfaces only, not on physical ports.

Configure the global IPv6 routing settings

You can configure the global IPv6 routing settings for the switch.

To enable IPv6 routing on the switch:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Routing> IPv6 > Basic > Global Configuration.

IcmpOutTimestamps The number of ICMP timestamp (request) messages.

IcmpOutTimestampReps The number of ICMP timestamp reply messages sent.

IcmpOutAddrMasks The number of ICMP address mask request messages sent.

Table 58. IP Statistics information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual226

6. Next to IPv6 Unicast Routing, specify whether IPv6 unicast routing is globally enabled by

selecting the Enable radio button or the Disable radio button.

7. In the Hop Limit field, enter a value for the unicast hop count used in IPv6 packets

originated by the node.

The value is also included in router advertisements. The valid values for hops are 1 to

255, inclusive. The default is Not Configured, which means that a value of zero is sent in

router advertisements.

8. In the ICMPv6 Rate Limit Error Interval field, specify the number of ICMP error packets

allowed per burst interval.

This value controls the ICMPv6 error packets. The default rate limit is 100 packets per

second, meaning that the burst interval is 1000 mseconds. To disable ICMP rate limiting,

set this field to 0. The valid rate interval must be in the range 0 to 2147483647 mseconds.

9. In the ICMPv6 Rate Limit Burst Size field, specify the number of ICMP error packets

allowed per burst interval.

This value controls the ICMP error packets. The default burst size is 100 packets. When

the burst interval is 0, then configuring this field is not a valid operation. The valid burst

size is 1 to 200.

10. Click the Apply button.

Your settings are saved.

View the IPv6 route table

To view the IPv6 route table:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Routing> IPv6 > Basic > Route Table.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual227

6. From the Routes Displayed menu, select one of the following options:

• All Routes. Show all active IPv6 routes.

• Best Routes Only. Show only the best active routes.

• Configured Routes Only. Show only the manually configured routes.

7. To refresh the page with the latest information about the switch, click the Update button.

The following table describes the nonconfigurable data that is displayed.

Table 59. IPv6 Route Table information

Field Description

Number of Routes The total number of active routes in the route table.

IPv6 Prefix The network prefix for the active route.

Prefix Length The prefix length for the active route.

Protocol The type of protocol for the active route.

Next Hop Interface The interface over which the route is active. For a reject route, the next

hop would be a Null0 interface.

Next Hop IP Address The next hop IPv6 address for the active route.

Preference The route preference of the configured route.

Configure IPv6 VLAN interface settings

Configure IPv6 VLAN interface settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual228

The default password is password.

The System Information page displays.

5. Select Routing> IPv6 > Advanced > VLAN Configuration.

6. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

7. From the IPv6 Mode menu, select Enable or Disable.

When IPv6 mode is enabled, the interface is capable of IPv6 operation without a global

address. In this case, an EUI-64-based link-local address is used. The default value is

Disable.

8. From the DHCPv6 Client Mode menu, select to enable or disable the DHCPv6 client mode

on an interface.

Only one interface can function as a client. The default value is Disable.

9. From the Stateless Address AutoConfig Mode menu, select to enable or disable the

stateless address autoconfiguration mode on an interface.

The default value is Disable.

10. From the Admin Mode menu, select to enable or disable the IPv6 mode.

The default is Disable. When the IPv6 mode is enabled, the interface is capable of IPv6

operation without a global address. In this case, an EUI-64-based link-local address is

used.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual229

11. In the MTU field, specify the maximum transmit unit (MTU) for an interface.

If the value is 0, then this interface is not enabled for routing. It is not valid to set this value

to 0 if routing is enabled. The MTU range 1280 to 1500. The default is 1500.

12. In the Duplicate Address Detection Transmits field, specify the number of duplicate

address detection (DAD) transmits on an interface.

The DAD transmits value must be in the range 0 to 600. The default is 1.

13. In the Life Time Interval field, specify the router advertisement life time interval that is sent

from the interface.

This value must be greater than or equal to the maximum advertisement interval.

0 means do not use the router as the default router. The range of router life time is 0 to

9000. The default is 1800.

14. In the Adv NS Interval field, specify the retransmission time field of router advertisements

sent from the interface.

A value of 0 means the interval is not specified for the router. The range of the neighbor

solicit interval is 1000 to 4294967295. The default is 0.

15. In the Adv Reachable Interval field, specify the router advertisement time.

This is the time allocated to consider the neighbors reachable after ND confirmation. The

range of reachable time is 0 to 3600000. The default is 0.

16. In the Adv Interval field, specify the maximum time allowed between sending router

advertisements from the interface.

The range of the maximum advertisement interval is 4 to 1800. The default value is 600.

17. From the Adv Managed Config Flag menu, specify the setting for the router advertisement

managed address configuration flag.

When the selection is Enable, end nodes use DHCPv6. When the selection is Disable,

end nodes autoconfigure addresses. The default value is Disable.

18. From the Adv Other Config Flag menu, select to enable or disable the router

advertisement other stateful configuration flag.

The default value is Disable.

19. From the Router Preference menu, specify the router preference advertisement on an

interface.

The default value is Medium.

20. From the Adv Suppress Flag menu, select to enable or disable the router advertisement

suppression on an interface.

The default value is Disable.

21. From the Destination Unreachables menu, select to enable or disable the mode for

sending ICMPv6 destination unreachable messages on this interface.

If this mode is disabled, the interface does not send ICMPv6 destination unreachable

messages. By default, the IPv6 destination unreachables mode is enabled.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual230

22. Click the Apply button.

Your settings are saved.

The following table describes the nonconfigurable data that is displayed.

Table 60. IPv6 VLAN Configuration information

Field Description

Routing Mode The routing mode of an interface. The default is Disable.

Operational Mode The operational state of an interface. The default value is Disable.

Link State Indicates whether the link is up or down.

Configure an IPv6 prefix

To configure an IPv6 prefix:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Routing> IPv6 > Advanced > Prefix Configuration.

6. From the Interface menu, select the interface to be configured.

When the selection is changed, the page refreshes, causing all fields to be updated for

the newly selected interface.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual231

7. In the IPv6 Prefix field, specify the IPv6 prefix for an interface.

8. In the Prefix Length field, specify the IPv6 prefix length for an interface.

9. From the EUI64 menu, select Enable or Disable to indicate whether the specified 64-bit

unicast prefix is enabled.

10. In the Valid Life Time field, specify the router advertisement per prefix time.

This is the time allowed to consider the prefix valid for the purpose of on-link

determination. The valid life time is 0 to 4294967295.

11. In the Preferred Life Time field, specify the router advertisement per prefix time.

An autoconfigured address generated from this prefix is preferred. The preferred life time

must be in the range 0 to 4294967295.

12. From the Onlink Flag menu, select Enable or Disable to specify whether the selected

prefix can be used for on-link determination.

The default is Enable.

13. From the Autonomous Flag menu, select Enable or Disable to specify whether the

selected prefix can be used for autonomous address configuration.

The default value is Enable.

The Current State field displays the state of the IPV6 address. The state is TENT if

routing is disabled or DAD fails. The state is Active if the interface is active and DAD is

successful.

14. Click the Add button.

The IPv6 address is added to the interface.

15. Click the Apply button.

Your settings are saved.

View the IPv6 routing statistics

To view the IPv6 routing statistics:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual232

The System Information page displays.

5. Select Routing> IPv6 > Advanced > Statistics.

6. From the Interface menu, select the interface.

When the selection is changed, the page refreshes, causing all fields to be updated for

the newly selected interface.

7. To refresh the page with the latest information about the switch, click the Update button.

The following table describes the nonconfigurable IPv6 data that is displayed.

Table 61. IPv6 Statistics information

Field Description

Total Datagrams Received The total number of input datagrams received by the interface, including

those received in error.

Received Datagrams Locally

Delivered The total number of datagrams successfully delivered to IPv6

user-protocols (including ICMP). This counter is incremented at the

interface to which these datagrams were addressed, which might not be

the input interface for some of the datagrams.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual233

Received Datagrams Discarded

Due To Header Errors The number of input datagrams discarded due to errors in their IPv6

headers, including version number mismatch, other format errors, hop

count exceeded, errors discovered in processing their IPv6 options, and

so on.

Received Datagrams Discarded

Due To MTU The number of input datagrams that could not be forwarded because their

size exceeded the link MTU of outgoing interface.

Received Datagrams Discarded

Due To No Route The number of input datagrams discarded because no route could be

found to transmit them to their destination.

Received Datagrams With Unknown

Protocol The number of locally addressed datagrams received successfully but

discarded because of an unknown or unsupported protocol. This counter

is incremented at the interface to which these datagrams were addressed,

which might not be the input interface for some of the datagrams.

Received Datagrams Discarded

Due To Invalid Address The number of input datagrams discarded because the IPv6 address in

their IPv6 header's destination field was not a valid address to be received

at this entity. This count includes invalid addresses (for example, ::0) and

unsupported addresses (such as addresses with unallocated prefixes).

For entities that are not IPv6 routers and therefore do not forward

datagrams, this counter includes datagrams discarded because the

destination address was not a local address.

Received Datagrams Discarded Dut

To Truncated Data The number of input datagrams discarded because datagram frame didn't

carry enough data.

Received Datagrams Discarded

Other The number of input IPv6 datagrams for which no problems were

encountered to prevent their continued processing, but that were

discarded for reasons such as lack of buffer space. This counter does not

include any datagrams discarded while awaiting reassembly.

Received Datagrams Reassembly

Required The number of IPv6 fragments received that needed to be reassembled at

this interface. This counter is incremented at the interface to which these

fragments were addressed, which might not be the input interface for

some of the fragments.

Datagrams Successfully

Reassembled The number of IPv6 datagrams successfully reassembled. This counter is

incremented at the interface to which these datagrams were addressed,

which might not be necessarily the input interface for some of the

fragments.

Datagrams Failed To Reassemble The number of failures detected by the IPv6 reassembly algorithm (for

whatever reason: timed out, errors, and so on). This is not necessarily a

count of discarded IPv6 fragments since some algorithms (notably the

algorithm in RFC 815) can lose track of the number of fragments by

combining them as they are received. This counter is incremented at the

interface to which these fragments were addressed, which might not be

the input interface for some of the fragments.

Datagrams Forwarded The number of output datagrams that this entity received and forwarded to

their final destinations. In entities that do not act as IPv6 routers, this

counter includes only those packets that were source-routed through this

entity, and the source-route processing was successful. For a successfully

forwarded datagram the counter of the outgoing interface is incremented.

Table 61. IPv6 Statistics information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual234

The following table describes the nonconfigurable ICMPv6 data that is displayed.

Datagrams Locally Transmitted The number of datagrams that this entity successfully transmitted from

this output interface.

Datagrams T ransmit Failed The number of datagrams that this entity failed to transmit successfully.

Datagrams Successfully

Fragmented The number of IPv6 datagrams that were fragmented at this output

interface.

Datagrams Failed To Fragment The number of output datagrams that could not be fragmented at this

interface.

Datagrams Fragments Created The number of output datagram fragments that were generated as a result

of fragmentation at this output interface.

Multicast Datagrams Received The number of multicast packets received by the interface.

Multicast Datagrams Transmitted The number of multicast packets transmitted by the interface.

Table 62. ICMPv6 Statistics information

Field Description

Total ICMPv6 Messages Received The total number of ICMP messages received by the interface, which

includes all those counted by IPv6IfIcmpInErrors. This interface is the

interface to which the ICMP messages were addressed, which might not

be the input interface for the messages.

ICMPv6 Messages With Errors

Received The number of ICMP messages that the interface received but determined

as having ICMP-specific errors (bad ICMP checksums, bad length, and so

on).

ICMPv6 Destination Unreachable

Messages Received The number of ICMP Destination Unreachable messages received by the

interface.

ICMPv6 Messages Prohibited

Administratively Received The number of ICMP destination unreachable/communication

administratively prohibited messages received by the interface.

ICMPv6 Time Exceeded Messages

Received The number of ICMP T ime Exceeded messages received by the interface.

ICMPv6 Parameter Problem

Messages Received The number of ICMP Parameter Problem messages received by the

interface.

ICMPv6 Packet Too Big Messages

Received The number of ICMP Packet Too Big messages received by the interface.

ICMPv6 Echo Request Messages

Received The number of ICMP Echo (request) messages received by the interface.

ICMPv6 Echo Reply Messages

Received The number of ICMP Echo Reply messages received by the interface.

Table 61. IPv6 Statistics information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual235

ICMPv6 Router Solicit Messages

Received The number of ICMP Router Solicit messages received by the interface.

ICMPv6 Router Advertisement

Messages Received The number of ICMP Router Advertisement messages received by the

interface.

ICMPv6 Neighbor Solicit Messages

Received The number of ICMP Neighbor Solicit messages received by the interface.

ICMPv6 Neighbor Advertisement

Messages Received The number of ICMP Neighbor Advertisement messages received by the

interface.

ICMPv6 Redirect Messages

Received The number of ICMPv6 Redirect messaged received by the interface.

ICMPv6 Group Membership Query

Messages Received The number of ICMPv6 Group Membership Query messages received by

the interface.

ICMPv6 Group Membership

Response Messages Received The number of ICMPv6 Group Membership Response messages received

by the interface.

ICMPv6 Group Membership

Reduction Messages Received The number of ICMPv6 Group Membership Reduction messages received

by the interface.

Total ICMPv6 Messages

Transmitted The total number of ICMP messages that this interface attempted to send.

This counter includes all those counted by icmpOutErrors.

ICMPv6 Messages Not Transmitted

Due To Error The number of ICMP messages that this interface did not send due to

problems discovered within ICMP such as a lack of buffers. This value

does not include errors discovered outside the ICMP layer such as the

inability of IPv6 to route the resultant datagram. In some implementations

there might be no types of error that contribute to this counter's value.

ICMPv6 Destination Unreachable

Messages T ransmitted The number of ICMP Destination Unreachable messages sent by the

interface.

ICMPv6 Messages Prohibited

Administratively T ransmitted Number of ICMP Destination Unreachable/Communication

Administratively Prohibited messages sent.

ICMPv6 Time Exceeded Messages

Transmitted The number of ICMP Time Exceeded messages sent by the interface.

ICMPv6 Parameter Problem

Messages T ransmitted The number of ICMP Parameter Problem messages sent by the interface.

ICMPv6 Packet Too Big Messages

Transmitted The number of ICMP Packet Too Big messages sent by the interface.

ICMPv6 Echo Request Messages

Transmitted The number of ICMP Echo (request) messages sent by the interface.

ICMPv6 Echo Reply Messages

Transmitted The number of ICMP Echo Reply messages sent by the interface.

ICMPv6 Router Solicit Messages

Transmitted The number of ICMP Neighbor Solicitation messages sent by the

interface.

Table 62. ICMPv6 Statistics information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual236

View, search, or clear the IPv6 neighbor table

To view, search, or clear the IPv6 neighbor table:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Routing> IPv6 > Advanced > Neighbor Table.

ICMPv6 Router Advertisement

Messages T ransmitted The number of ICMP Router Advertisement messages sent by the

interface.

ICMPv6 Neighbor Solicit Messages

Transmitted The number of ICMP Neighbor Solicitation messages sent by the

interface.

ICMPv6 Neighbor Advertisement

Messages T ransmitted The number of ICMP Neighbor Advertisement messages sent by the

interface.

ICMPv6 Redirect Messages

Transmitted The number of Redirect messages sent.

ICMPv6 Group Membership Query

Messages T ransmitted The number of ICMPv6 Group Membership Query messages sent.

ICMPv6 Group Membership

Response Messages Transmitted The number of ICMPv6 Group Membership Response messages sent.

ICMPv6 Group Membership

Reduction Messages Transmitted The number of ICMPv6 Group Membership Reduction messages sent.

ICMPv6 Duplicate Address Detects The number of duplicate addresses detected by the interface.

Table 62. ICMPv6 Statistics information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual237

6. Use the Search menu and field to search for IPv6 routes by IPv6 address or interface

number:

• Search by IPv6 address. Select IPv6 Address from the Search menu. Enter the

128-byte hexadecimal IPv6 address in four-digit groups separated by colons, for

example, 2001:231F:::1. Then click the Go button.

If the address exists, the entry is displayed. An exact match is required.

• Search by Interface. Select Interface from the Search menu. Enter the interface

using the respective naming convention (for example, g1 or l1). Then click the Go

button.

If the address exists, the entry is displayed.

7. To clear the IPv6 neighbors on a selected interface or on all interfaces, click the Clear

button.

8. To refresh the page with the latest information about the switch, click the Update button.

The following table describes the nonconfigurable data that is displayed.

Table 63. IPv6 Neighbor Table information

Field Description

Interface The interface whose settings are displayed in the current table row.

IPv6 Address The IPv6 address of the neighbor or interface.

MAC Address The MAC address associated with an interface.

isRtr Indicates whether the neighbor is a router. If the neighbor is a router, the

value is True. If the neighbor is not a router, the value is False.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual238

Configure an IPv6 static route

To configure an IPv6 static route

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Routing> IPv6 > Advanced > Static Route Configuration.

Neighbor State The state of the neighbor cache entry. Following are the states for

dynamic entries in the IPv6 neighbor discovery cache:

• Incmp. Address resolution is being performed on the entry. A

neighbor solicitation message was sent to the solicited-node multicast

address of the target, but the corresponding neighbor advertisement

message is not yet received.

• Reach. Positive confirmation was received within the last Reachable

Time milliseconds that the forward path to the neighbor was

functioning properly. While in REACH state, the device takes no

special action as packets are sent.

• Stale. More than Reachable Time milliseconds elapsed since the last

positive confirmation was received that the forward path was

functioning properly. While in STALE state, the device takes no action

until a packet is sent.

• Delay. More than Reachable Time milliseconds elapsed since the last

positive confirmation was received that the forward path was

functioning properly. A packet was sent within the last

DELAY_FIRST_PROBE_TIME seconds. If no reachability

confirmation is received within DELAY_FIRST_PROBE_TIME

seconds of entering the DELAY state, send a neighbor solicitation

message and change the state to PROBE.

• Probe. Seeks a reachability confirmation by resending neighbor

solicitation messages every Retrans Timer milliseconds until a

reachability confirmation is received.

Last Updated The time since the address was confirmed to be reachable.

Table 63. IPv6 Neighbor Table information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual239

6. In the IPv6 Prefix field, specify the IPv6 network prefix for the configured route.

7. In the Prefix Length field, specify the IPv6 prefix length for the configured route.

8. From the Next Hop IPv6 Address Type menu, select one of the following options:

•Global. Select this option if the IPv6 address is a global IPv6 address.

• Link-Local. Select this option if the next hop IPv6 address is a link-local IPv6

address. You must specify a next hop IPv6 address in the Next Hop IPv6 Address

field.

• Static-Reject. Select this option to create a static-reject route for a destination prefix.

You do not need to specify a next hop IPv6 address.

9. If the selection from the Next Hop IPv6 Address Type menu is Global or Link-Local, enter

the next hop IPv6 address in the Next Hop IPv6 Address field.

10. If the selection from the Next Hop IPv6 Address Type menu is Link-Local, from the

Interface menu, select the interface that connects to the IPv6 next hop.

11. In the Preference field, specify the router preference.

12. Click the Add button.

The route is added.

Note: For information about viewing routes in the IPv6 route table, see View

the IPv6 route table on page 226

Configure the IPv6 route preferences

You can configure the default preference for each protocol. These values are arbitrary values

in the range of 1 to 255 and are independent of route metrics. Most routing protocols use a

route metric to determine the shortest path known to the protocol, independent of any other

protocol. The switch selects the route with the lowest preference value as the best route to a

destination. When multiple routes to a destination exist, the preference values are used to

determine the preferred route. If these preference values routes are equal, the route with the

best route metric is chosen. To avoid problems with mismatched metrics, you must configure

different preference values for each of the protocols.

Configure the IPv6 route preferences:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual240

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Routing> IPv6 > Advanced > Route Preference.

6. In the Static field, specify the static route preference value for the router.

The range is 1 to 255. The default value is 1.

7. Click the Apply button.

Your settings are saved. The Local field displays the local preference.

Configure VLAN routing

You can configure the switch with some ports supporting VLANs and some ports supporting

routing. You can also configure the switch to allow traffic on a VLAN to be treated as if the

VLAN were a router port.

When a port is enabled for bridging (the default setting) rather than routing, all normal bridge

processing is performed for an inbound packet, which is then associated with a VLAN. Its

MAC destination address (MAC DA) and VLAN ID are used to search the MAC address

table. If routing is enabled for the VLAN, and the MAC DA of an inbound unicast packet is

that of the internal bridge-router interface, the packet is routed. An inbound multicast packet

is forwarded to all ports in the VLAN. If a routed VLAN receives the multicast packet, the

packet is also forwarded on the internal bridge-router interface.

Because you can configure a port to belong to more than one VLAN, VLAN routing might be

enabled for all of the VLANs on the port, or for a subset. You can use VLAN routing to allow

more than one physical port to reside on the same subnet. You can also use VLAN routing if

a VLAN spans multiple physical networks, or if you require additional segmentation or

security. A port can either be a VLAN port or a router port, but not both. However, a VLAN

port can be part of a VLAN that is itself a router port.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual241

Create a routing interface with the VLAN Static Routing

Wizard

The VLAN Static Routing Wizard lets you create a VLAN routing interface, configure the IP

address and subnet mask for the interface, and add ports, LAGs, or both to the VLAN. With

this wizard, you can do the following:

•Create a VLAN.

•Add ports to the newly created VLAN and remove selected ports from the default VLAN.

•Optionally, create a LAG, add ports to the LAG, then add the LAG to the newly created

VLAN.

•Enable tagging on selected ports if the port is in another VLAN. Disable tagging if a

selected port does not exist in another VLAN.

•Enable routing on the VLAN using the IP address and subnet mask entered.

To use the VLAN Static Routing Wizard:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Routing> VLAN > VLAN Routing Wizard.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual242

6. In the VLAN ID field, specify the VLAN ID that is associated with the VLAN.

The range of the VLAN ID is 1 to 4093.

7. In the IP Address field, define the IP address of the VLAN interface.

8. In the Network Mask field, define the subnet mask of the VLAN interface.

9. In the Ports table, click each port once, twice, or three times to configure one of the following

modes or reset the port to the default settings:

• T (T agged). Select the ports on which all frames transmitted for this VLAN are tagged.

The ports that are selected are included in the VLAN.

• U (Untagged). Select the ports on which all frames transmitted for this VLAN are

untagged. The ports that are selected are included in the VLAN.

By default, the selection is blank, which means that the port is excluded from the VLAN

but can be dynamically registered (autodetected) in the VLAN through GVRP.

10. In the LAG table, click each LAG once, twice, or three times to configure one of the following

modes or reset the LAG to the default settings:

• T (Tagged). Select the LAGs on which all frames transmitted for this VLAN are

tagged. The LAGs that are selected are included in the VLAN.

• U (Untagged). Select the LAGs on which all frames transmitted for this VLAN are

untagged. The LAGs that are selected are included in the VLAN.

By default, the selection is blank, which means that the LAG is excluded from the VLAN

but can be dynamically registered (autodetected) in the VLAN through GVRP.

11. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual243

Manage a VLAN routing interface

You can add and manage an existing VLAN (see Configure the VLAN Settings on

page 140) as a new VLAN routing interface. You can also manage an existing VLAN routing

interface that you added with the wizard (see Create a routing interface with the VLAN Static

Routing Wizard on page 241),

To add or change a VLAN routing interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Routing> VLAN > VLAN Routing Configuration.

6. From the VLAN menu, select the VLAN.

This menu displays the IDs of all VLANs that are configured on the switch.

7. In the IP Address field, enter the IP address to be configured for the VLAN routing interface.

8. In the Subnet Mask field, enter the subnet mask to be configured for the VLAN routing

interface.

9. In the IP MTU field, specify the maximum size of IP packets that can be sent on an

interface. The valid range is from 68 bytes to the link MTU. The default value is 1500. A

value of 0 indicates that the IP MTU is unconfigured. When the IP MTU is unconfigured, the

router uses the link MTU as the IP MTU. The link MTU is the maximum frame size minus

the length of the Layer 2 header.

10. Click the Add button.

The VLAN routing interface is added for the selected VLAN ID.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual244

The entry in the MAC Address field is automatically entered.

The following table describes the nonconfigurable information displayed on the page.

Table 64. VLAN Routing Configuration information

Field Description

Port The interface that is assigned to the VLAN for routing.

MAC Address The MAC address that is assigned to the VLAN routing interface.

Routing Mode Indicates whether routing is enabled for the VLAN routing Interface.

Delete a VLAN routing interface

You can delete a VLAN routing interface that you no longer need.

To delete a VLAN routing interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Routing> VLAN > VLAN Routing Configuration.

The VLAN Routing Configuration page displays.

6. From the VLAN menu, select the VLAN.

7. Click the Delete button.

The VLAN routing interface is removed. The VLAN itself is not removed.

Configure router discovery for a VLAN routing interface

By default, a VLAN routing interface does not send router advertisements.You can enable the

router advertisements for a VLAN routing interface and configure the setting for the router

advertisements.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual245

To configure router discovery for a VLAN routing interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Routing> Router Discovery > Router Discovery Configuration.

6. Select a check box to the left of the Interface column to select the router interface.

7. From the Advertise Mode menu, select Enable or Disable.

If you select Enable, router advertisements are transmitted from the selected interface.

8. In the Advertise Address field, specify the IP address that must be advertised.

In the Maximum Advertise Interval field, enter the maximum time (in seconds) allowed

between router advertisements sent from the interface. The default value is 600.

9. In the Minimum Advertise Interval field, enter the minimum time (in seconds) allowed

between router advertisements sent from the interface.

The value must be in the range of 3 to 1800. The default value is 450.

In the Advertise Lifetime field, enter the value (in seconds) to be used as the lifetime

field in router advertisements sent from the interface.

This is the maximum length of time that the advertised addresses are to be considered as

valid router addresses by hosts. The default value is 1800.

10. In the Preference Level field, specify the preference level of the router as a default router

relative to other routers on the same subnet.

Higher numbered addresses are preferred. You must enter an integer. The default value

is 0.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual246

11. Click the Apply button.

Your settings are saved.

Manage routes and view the routing table

The routing table collects routes from multiple sources: static routes and local routes. The

routing table can learn multiple routes to the same destination from multiple sources. The

routing table lists all routes.

Manually add a route and view the routing table

To manually add a default route or static route and view the routing table:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Routing> Routing Table > Route Configuration.

6. From the Route Type menu, select one of the following route types.

• DefaultRoute. Creates a default route. You must specify the next hop address and

preference.

•Static. Creates a static route. You must specify the network address, subnet mask,

next hop address, and preference.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual247

Depending on the type of route that you are creating, specify the following information:

•In the Network Address field, specify the portion of the IP interface address that

identifies the attached network.

This is also referred to as the subnet/network mask.

•In the Next Hop IP Address field, specify the outgoing router IP address to use when

forwarding traffic to the next router (if any) in the path toward the destination.

The next router is always one of the adjacent neighbors or the IP address of the local

interface for a directly attached network.

•In the Preference field, specify the preference, which is an integer value from 1

to 255.

You can specify the preference value (sometimes called administrative distance) of

an individual static route. Among routes to the same destination, the route with the

lowest preference value is the route entered into the forwarding database. By

specifying the preference of a static route, you control whether a static route is more

or less preferred than routes from dynamic routing protocols. The preference also

controls whether a static route is more or less preferred than other static routes to the

same destination.

•In the Description field, enter a description for the route.

The description must consist of alphanumeric, hyphen, or underscore characters and

can be up to 31 characters in length.

7. Click the Add button.

The static route is added to the switch.

8. Click the Apply button.

Your settings are saved.

9. To refresh the page with the latest information about the switch, click the Update button.

The following table describes the nonconfigurable data that is displayed.

Table 65. Learned Routes information

Field Description

Network Address The IP route prefix for the destination.

Subnet Mask The portion of the IP interface address that identifies the attached network (also referred

to as the subnet or network mask).

Protocol The protocol that created the specified route. The possibilities are one of the following:

• Local

• Static

Route Type The route type can be Connected, Static, or Dynamic, depending on the protocol.

Next Hop Interface The outgoing router interface to use when forwarding traffic to the destination.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual248

Modify a route

You can modify an existing route.

To modify an existing route:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Routing> Routing Table > Route Configuration.

The Configure Routes page displays.

6. Select the check box for the route that you want to modify.

7. Modify the settings.

For more information, see Manually add a route and view the routing table on

page 246.

8. Click the Apply button.

Your settings are saved.

Next Hop Address The outgoing router IP address to use when forwarding traffic to the next router (if any) in

the path toward the destination. The next router is always one of the adjacent neighbors

or the IP address of the local interface for a directly attached network.

Preference The preference is an integer value from 0 to 255. The user can specify the preference

value (sometimes called administrative distance) of an individual static route. Among

routes to the same destination, the route with the lowest preference value is the route

entered into the forwarding database. By specifying the preference of a static route, you

control whether a static route is more or less preferred than routes from dynamic routing

protocols. The preference also controls whether a static route is more or less preferred

than other static routes to the same destination.

Metric The administrative cost of the path to the destination. If no value is entered, the default

is 1. The range is 0–255.

Table 65. Learned Routes information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual249

Delete a route

You can delete a route that you no longer need.

To delete a route:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Routing> Routing Table > Route Configuration.

The Configure Routes page displays.

6. Select the check box for the route that you want to delete.

7. Click the Delete button.

The route is deleted.

Configure Address Resolution Protocol

The Address Resolution Protocol (ARP) associates a Layer 2 MAC address with a Layer 3

IPv4 address. ARP is a part of the Internet Protocol (IP) and is used to translate an IP

address to a media (MAC) address, defined by a LAN such as an Ethernet LAN.

The switch supports both dynamic and manual ARP configurations. With a manual ARP

configuration, you can statically add entries to the ARP table.

A device that sends an IP packet must learn the MAC address of the IP destination, or, if the

destination is not on the same subnet, of the next hop router. The device broadcasts an ARP

request packet, to which the intended recipient responds with a unicast ARP reply that

contains its MAC address. The device then uses the MAC address in the destination address

field of the Layer 2 header that is prepended to the IP packet and sent to the recipient. Each

device in a network maintains its ARP cache locally.

The switch learns ARP cache entries by examining the source information in the ARP packet

payload fields, regardless of whether it is an ARP request or a response. In that way, when

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual250

an ARP request is broadcast to all stations on a LAN segment or VLAN, each recipient can

store the sender’s IP and MAC address in its ARP cache. Normally, only the requestor

receives an ARP response (a unicast message) and stores the sender’s information in its

ARP cache. The most recent information always replaces existing content in the ARP cache.

A device can be moved in a network, which means that the device’s IP address that was

associated with one MAC address is now associated with another MAC address. A device

can also disappear from the network altogether (for example, it was reconfigured,

disconnected, or powered off). These situations cause stale information in the ARP cache.

Therefore, entries are updated or periodically refreshed to determine if an address still exists.

If an entry was identified as a sender of an ARP packet, the entry can be removed from the

ARP cache. You can configure an age-out interval that determines how long an entry that is

not updated remains in the ARP cache.

View the ARP cache

You can view ARP entries in the ARP cache. The ARP cache is a table that lists the remote

connections that were recently detected by the switch.

To view entries in the ARP cache:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Routing> ARP > Basic > ARP Cache.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual251

6. Navigate through the table by doing the following:

•From the Rows per page menu, select how many table entries are displayed per

page.

Possible values are 20, 50, 100, 200, and All. If you select All, the browser might be

slow to display the information.

•Click the < button to display the previous page of the table data entries.

•Click the > button to display the next page of the table data entries.

7. To refresh the page with the latest information about the switch, click the Update button.

The following table describes the nonconfigurable information displayed on the page.

Table 66. ARP cache information

Field Description

Management VLAN ARP Cache

IP Address The IP address associated with the system’s MAC address. This must be the IP

address of a device on a subnet attached to one of the switch’s existing routing

interfaces.

Port The associated interface ID of the connection.

MAC Address The unicast MAC address of the device. The address is six two-digit hexadecimal

numbers separated by colons, for example, 00:06:29:32:81:40.

Routing VLANs ARP Cache

IP Address The IP address. It must be the IP address of a device on a subnet attached to one of

the switch’s existing routing interfaces.

Interface The routing interface associated with the ARP entry.

MAC Address The unicast MAC address of the device. The address is six two-digit hexadecimal

numbers separated by colons, for example 00:06:29:32:81:40.

Type The type of ARP entry. Possible values are as follows:

Age The time since the entry was last refreshed in the ARP table (in seconds).

• Local. An ARP entry associated with one of the switch’s routing interface’s

MAC addresses.

• Gateway. A dynamic ARP entry whose IP address is that of a router.

• Static. An ARP entry configured by the user.

• Dynamic. An ARP entry that was learned by the router.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual252

Manually add an entry to the ARP table

You can manually add an entry to the ARP table.

To manually add an entry to the ARP table:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Routing> ARP > Advanced > ARP Create.

6. In the IP Address field, specify an IP address.

This must be the IP address of a device on a subnet attached to one of the switch's

existing routing interfaces.

7. In the MAC Address field, specify the unicast MAC address of the device.

Enter the address as six two-digit hexadecimal numbers separated by colons, for

example, 00:06:29:32:81:40.

8. Click the Add button.

The static ARP entry is added to the switch.

9. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual253

The following table describes the nonconfigurable information displayed on the page. You

can navigate through the table by doing the following:

•From the Rows per page menu, select how many table entries are displayed per

page.

Possible values are 20, 50, 100, 200, and All. If you select All, the browser might be

slow to display the information.

•Click the < button to display the previous page of the table data entries.

•Click the > button to display the next page of the table data entries.

Table 67. Routing VLANs ARP Cache information

Field Description

IP Address The IP address. It must be the IP address of a device on a subnet attached to one of the

switch’s existing routing interfaces.

Interface The routing interface associated with the ARP entry.

MAC Address The unicast MAC address of the device. The address is six two-digit hexadecimal

numbers separated by colons, for example, 00:06:29:32:81:40.

Type The type of ARP entry. Possible values are as follows:

Age The time since the entry was last refreshed in the ARP table (in seconds).

View or globally configure the ARP table

You can change the global settings for the ARP table.

To view or configure the ARP table:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

• Local. An ARP entry associated with one of the switch’s routing interface’s MAC

addresses.

• Gateway. A dynamic ARP entry whose IP address is that of a router.

• Static. An ARP entry configured by the user.

• Dynamic. An ARP entry that was learned by the router.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual254

The System Information page displays.

5. Select Routing> ARP > Advanced > Global ARP Configuration.

6. In the Age Time field, enter the time, in seconds, that a dynamic ARP entry remains in the

ARP table before aging out.

The range is 15 to 21600 seconds. The default value is 1200 seconds.

7. In the Response Time field, enter the time, in seconds, that the device waits for an ARP

response to an ARP request that it sends. The range for this field is 1 to 10 seconds. The

default value is 1 second.

8. In the Retries field, enter the maximum number of times an ARP request is retried after an

ARP response is not received.

The number includes the initial ARP request. The range for this field is 0 to 10. The

default value is 4.

9. In the Cache Size field, specify the maximum number of entries allowed in the ARP table.

This number includes all static and dynamic ARP entries.The range for this field is 79 to

738. The default value is 738.

10. Select the Dynamic Renew Enable or Disable radio button.

When enabled, the ARP component automatically attempts to renew dynamic ARP

entries when they age out. The default setting is Enable.

11. Click the Apply button.

Your settings are saved.

Remove ARP entries from the ARP cache

You can remove entries from the ARP cache.

To remove entries from the ARP cache:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Routing User Manual255

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Routing> ARP > Advanced > ARP Entry Management.

6. From the Remove From Table menu, select the type of ARP entry to be deleted:

• All Dynamic Entries

• All Dynamic and Gateway Entries

• Specific Dynamic/Gateway Entry. Lets you specify the IP address to be removed.

• Specific Static Entry. Lets you specify the IP address to be removed.

7. If you select Specific Dynamic/Gateway Entry or Specific Static Entry, in the Remove IP

Address field, enter the IP address to be removed.

8. Click the Apply button.

Your settings are saved.

256

5Configure Quality of Service

This chapter covers the following topics:

•Quality of Service concepts

•Manage the Class of Service

•Manage Differentiated Services

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual257

Quality of Service concepts

In a switch, each physical port consists of one or more queues for transmitting packets on the

attached network. Multiple queues per port are often provided to give preference to certain

packets over others based on user-defined criteria. When a packet is queued for

transmission in a port, the rate at which it is serviced depends on how the queue is

configured and possibly the amount of traffic present in the other queues of the port. If a

delay is necessary, packets are held in the queue until the scheduler authorizes the queue for

transmission. As queues become full, packets can no longer be held for transmission and are

dropped by the switch.

Quality of Service (QoS) is a means of providing consistent, predictable data delivery by

distinguishing packets with strict timing requirements from those that are more tolerant of

delay. Packets with strict timing requirements are given special treatment in a QoS-capable

network. With this in mind, all elements of the network must be QoS capable. The presence

of at least one node that is not QoS capable creates a deficiency in the network path, and the

performance of the entire packet flow is compromised.

Manage the Class of Service

The Class of Service (CoS) queueing feature lets you directly configure certain aspects of

switch queueing. This provides the desired QoS behavior for dif ferent types of network traf fic

when the complexities of DiffServ are not required. The priority of a packet arriving at an

interface can be used to steer the packet to the appropriate outbound CoS queue through a

mapping table. CoS queue characteristics that affect queue mapping, such as minimum

guaranteed bandwidth or transmission rate shaping, are user configurable at the queue (or

port) level.

Eight queues per port are supported.

CoS configuration concepts

You can set the Class of Service trust mode for an interface. Each port in the switch can be

configured to trust one of the packet fields (802.1p or IP DSCP), or to not trust any packet’s

priority designation (untrusted mode). If the port is set to a trusted mode, it uses a mapping

table appropriate for the trusted field being used. This mapping table indicates the CoS

queue to which the packet must be forwarded on the appropriate egress port. Of course, the

trusted field must exist in the packet for the mapping table to be of any use. If this is not the

case, default actions are performed. These actions involve directing the packet to a specific

CoS level configured for the ingress port as a whole, based on the existing port default

priority as mapped to a traffic class by the current 802.1p mapping table.

Alternatively, when a port is configured as untrusted, it does not trust any incoming packet

priority designation and uses the port default priority value instead. All packets arriving at the

ingress of an untrusted port are directed to a specific CoS queue on the appropriate egress

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual258

ports, in accordance with the configured default priority of the ingress port. This process is

also used for cases where a trusted port mapping cannot be honored, such as when a non-IP

packet arrives at a port configured to trust the IP DSCP value.

Configure the global CoS settings

A global configuration setting is automatically applied to all interfaces on the switch.

To configure the CoS trust mode settings on all interfaces:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS> CoS > Basic > CoS Configuration.

6. Either configure the same CoS trust mode settings for all CoS-configurable interfaces or

configure CoS settings per interface.

By default, the Global radio button is selected.

•To configure the same CoS trust mode settings for all CoS configurable interfaces, do

the following:

a. Select the Global radio button.

b. From the Global Trust Mode menu, select one of the following trust mode

options for ingress traffic on the switch:

-Untrusted. Do not trust any CoS packet marking at ingress.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual259

- 802.1p. The eight priority tags that are specified in IEEE 802.1p are p0 to p7.

The QoS setting lets you map each of the eight priority levels to one of seven

internal hardware priority queues. The default mode is 802.1p.

- DSCP. The six most significant bits of the DiffServ field are called the

Differentiated Services Code Point (DSCP) bits.

•To configure CoS settings per interface, do the following:

a. Select the Interface radio button.

b. From the Interface Trust Mode menu, select one of the following trust mode

options:

- Untrusted. Do not trust any CoS packet marking at ingress.

- 802.1p. The eight priority tags that are specified in IEEE 802.1p are p0 to p7.

The QoS setting lets you map each of the eight priority levels to one of seven

internal hardware priority queues. The default mode is 802.1p.

- DSCP. The six most significant bits of the DiffServ field are called the

Differentiated Services Code Point (DSCP) bits.

7. Click the Apply button.

Your settings are saved.

Configure CoS interface settings for an interface

You can configure the trust mode for one or more interfaces and apply an interface shaping

rate to all interfaces or to a specific interface.

To configure CoS settings for an interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > CoS > Advanced > CoS Interface Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual260

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8. From the Interface Trust Mode menu, select one of the following trust mode options for

ingress traffic on the selected interfaces:

• Untrusted. Do not trust any CoS packet marking at ingress.

• 802.1p. The eight priority tags that are specified in IEEE 802.1p are p0 to p7. The

QoS setting lets you map each of the eight priority levels to one of seven internal

hardware priority queues. The default value is 802.1p.

• DSCP. The six most significant bits of the DiffServ field are called the Differentiated

Services Code Point (DSCP) bits.

9. In the Interface Shaping Rate field, specify the maximum bandwidth allowed.

This is typically used to shape the outbound transmission rate in increments of 64 kbps in

the range 16 to 16384 kbps.This value is controlled independently of any per-queue

maximum bandwidth configuration. It is effectively a second-level shaping mechanism.

The default value is 0. The value 0 means that the maximum is unlimited.

The expected shaping at egress interface is calculated as follows:

frameSize × shaping/(frameSize + IFG), where IFG (Inter frame gap) is 20 bytes,

frameSize is configured frame size, and shaping is configured traffic shaping.

For example, when 64 bytes frame size and 64 kbps shaping are configured, expected

shaping is approximately 48 kbps.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual261

10. Click the Apply button.

Your settings are saved.

Configure the CoS queue settings for an interface

You can define what a particular queue does by configuring switch egress queues. You can

control how much bandwidth is used by the queue, the queue depth during times of

congestion, and the scheduling of packet transmission from all queues on a port. Each port

contains its own CoS queue-related configuration.

For information about configuring CoS queue settings globally, see Configure the global

CoS settings on page 258.

To configure CoS queue settings for an interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > CoS > Advanced > Interface Queue Configuration.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual262

7. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8. From the Queue ID menu, select the queue to be configured.

9. In the Minimum Bandwidth field, specify the minimum guaranteed bandwidth allotted to the

queue.

Setting this value higher than its corresponding maximum bandwidth automatically

increases the maximum to the same value. The default value is 0. The valid range is 0 to

100 in increments of 1. The value 0 means no guaranteed minimum. The sum of the

individual minimum bandwidth values for all queues for the interface cannot exceed the

defined maximum (100).

10. From the Scheduler Type menu, select one of the following options:

•Strict. The interface services traffic with the highest priority on a queue first.

•Weighted. The interface uses weighted round robin to associate a weight to each

queue. This is the default setting.

The Queue Management Type field displays the queue depth management technique

that is used for queues on the interface. By default, this method is Taildrop, irrespective of

your selection from the Scheduler Type menu.

11. Click the Apply button.

Your settings are saved.

Map 802.1p priorities to queues

You can view or change which internal traffic classes are mapped to the 802.1p priority class

values in Ethernet frames that the device receives. The priority-to-traffic class mappings can

be applied globally or per interface. The mapping allows the switch to group various traffic

types (for example, data or voice) based on their latency requirements and give preference to

time-sensitive traffic.

To map 802.1p priorities to queues:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual263

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > CoS > Advanced > 802.1p to Queue Mapping.

6. Select the Global radio button to specify all interfaces (that can be configured for CoS) or

select the Interface radio button to select individual interfaces.

7. In the 802.1p to Queue Mapping table, map each of the eight 802.1p priorities to a queue

(internal traffic class).

The 802.1p Priority row contains traffic class selectors for each of the eight 802.1p

priorities to be mapped. The priority goes from low (0) to high (7). For example, traf fic with

a priority of 0 is for most data traffic and is sent using best effort. Traffic with a higher

priority, such as 7, might be time-sensitive traffic, such as voice or video.

The values in the menu under each priority represent the traffic class. The traffic class is

the hardware queue for a port. Higher traffic class values indicate a higher queue

position. Before traffic in a lower queue is sent, it must wait for traffic in higher queues to

be sent.

8. Click the Apply button.

Your settings are saved.

Map DSCP values to queues

You can map an internal traffic class to a DSCP value.

To map DSCP values to queues:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual264

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > CoS > Advanced > DSCP to Queue Mapping.

6. For each DSCP value, select from the corresponding Queue menu which internal traffic

class must be mapped to the DSCP value.

The traffic class is the hardware queue for a port. Higher traffic class values indicate a

higher queue position. Before traffic in a lower queue is sent, it must wait for traffic in

higher queues to be sent.

The allowed Per Hop Behavior (PHBs) values, apart from other DSCP experimental

values, are as follows:

•Class Selector (CS) PHB. These values are based on IP precedence.

• Assured Forwarding (AF) PHB. These values define four main levels to sort and

manipulate some flows within the network.

• Expedited Forwarding (EF) PHB. These values are used to prioritize traffic for

real-time applications. In many situations, if the network exceeded traffic and you

need some bandwidth guaranteed for an application, the EF traffic must receive this

rate independently of the intensity of any other traffic attempting to transit the node.

7. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual265

Manage Differentiated Services

The QoS feature contains Differentiated Services (DiffServ) support that allows traffic to be

classified into streams and given certain QoS treatment in accordance with defined per-hop

behaviors.

Standard IP-based networks are designed to provide best effort data delivery service. Best

effort service implies that the network delivers the data in a timely fashion, although there is

no guarantee. During times of congestion, packets might be delayed, sent sporadically, or

dropped. For typical Internet applications, such as email and file transfer , a slight degradation

in service is acceptable and in many cases unnoticeable. Conversely, any degradation of

service can negatively affect applications with strict timing requirements, such as voice or

multimedia.

Defining DiffServ

To use DiffServ for QoS, you must first define the following categories and their criteria:

1. Class. Create classes and define class criteria.

2. Policy. Create policies, associate classes with policies, and define policy statements.

3. Service. Add a policy to an inbound interface.

Packets are classified and processed based on defined criteria. The classification criteria are

defined by a class. The processing is defined by a policy’ s attributes. Policy attributes can be

defined on a per-class instance basis, and it is these attributes that are applied when a match

occurs. A policy can contain multiples classes. When the policy is active, the actions taken

depend on which class matches the packet.

Note the following about the DiffServ process:

•Packets are filtered and processed based on defined criteria. The filtering criteria is

defined by a class. The processing is defined by a policy's attributes. Policy attributes can

be defined on a per-class instance basis, and it is these attributes that are applied when a

match occurs.

•The configuration process begins with defining one or more match criteria for a class.

Then one or more classes are added to a policy. Policies are then added to interfaces.

Packet processing begins by testing the match criteria for a packet. The All class type option

specifies that each match criteria within a class must evaluate to true for a packet to match

that class. The Any class type option specifies that at least one match criteria must evaluate

to true for a packet to match that class. Classes are tested in the order in which they were

added to the policy. A policy is applied to a packet when a class match within that policy is

found.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual266

Configure the DiffServ mode and display the entries in the

DiffServ private MIB tables

You can enable or disable DiffServ and display the current and maximum number of rows in

each of the main DiffServ private MIB tables.

To configure the DiffServ mode and display the entries in the DiffServ private MIB

tables:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > DiffServ > Advanced > DiffServ Configuration.

6. Select the administrative mode for DiffServ:

• Enable. Differentiated services are active. This is the default setting.

•Disable. The DiffServ configuration is retained and can be changed but is not active.

7. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual267

The following table describes the information displayed in the Status table on the DiffServ

Configuration page.

Table 68. DiffServ Status information

Field Description

Class Table The number of configured DiffServ classes out of the total allowed on the switch.

Class Rule table The number of configured class rules out of the total allowed on the switch.

Policy table The number of configured policies out of the total allowed on the switch.

Policy Instance table The number of configured policy class instances out of the total allowed on the

switch.

Policy Attributes table The number of configured policy attributes (attached to the policy class instances)

out of the total allowed on the switch.

Service table The number of configured services (attached to the policies on specified interfaces)

out of the total allowed on the switch.

Configure a DiffServ class

You can add a new DiffServ class name, or rename or delete an existing class. You can also

define the criteria to associate with a DiffServ class. As packets are received, these DiffServ

classes are used to prioritize packets. You can set up multiple match criteria in a class. The

logic is a Boolean logical AND for this criteria. After creating a class, click the class link to the

Class page.

Add and configure a DiffServ class

To add and configure a DiffServ class:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual268

5. Select QoS > DiffServ > Advanced > Class Configuration.

6. In the Class Name field, enter a class name.

The Class Name field also lists all the existing Dif fServ class names, from which you can

select one for modification or deletion. The class name can be 1 to 31 alphanumeric

characters in length.

7. From the Class Type menu, select the class type.

The switch supports only the class type value All, which means that all the various match

criteria defined for the class are satisfied for a packet match. All signifies the logical AND

statement of all the match criteria. You can select the class type only when you are

creating a new class. After the class is created, the Class Type field becomes

nonconfigurable.

8. Click the Add button.

The new class is added.

9. After creating the class, click the class name.

The class name is a hyperlink to the page on which you can define the class

configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual269

10. Define the criteria that must be associated the DiffServ class:

• Match Every. Select this radio button to add a match condition that considers all

packets to belong to the class. The only selection from the Match Every menu is Any.

•Reference Class. Select this radio button to reference another class for criteria. The

match criteria defined in the reference class function as match criteria in addition to

the match criteria that you define for the selected class. After you select the radio

button, the classes that can be referenced are displayed. Select the class to

reference. A class can reference at most one other class of the same type.

• Class of Service. Select this radio button to require the Class of Service (CoS) value

in an Ethernet frame header to match the specified CoS value. This option lists all the

values for the Class of Service match criterion in the range 0 to 7 from which one can

be selected.

• VLAN. Select this radio button to require a packet’s VLAN ID to match a VLAN ID or a

VLAN ID within a continuous range. If you configure a range, a match occurs if a

packet’s VLAN ID is the same as any VLAN ID within the range. The VLAN value is in

the range of 0–4093.

• Ethernet T ype. Select this radio button to require the EtherType value in the Ethernet

frame header to match the specified EtherType value. After you select the radio

button, specify the EtherType keyword from the list of common protocols that are

mapped to their Ethertype value.

• Source MAC. Select this radio button to require a packet’s source MAC address to

match the specified MAC address. After you select this radio button, use the following

fields to configure the source MAC address match criteria:

-Address. The source MAC address to match. The source MAC address is

specified as six two-digit hexadecimal numbers separated by colons.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual270

- Mask. The MAC mask, which specifies the bits in the source MAC address to

compare against the Ethernet frame. Use Fs and zeros to configure the MAC

mask. An F means that the bit is checked, and a zero in a bit position means that

the data is not significant. For example, if the MAC address is aa:bb:cc:dd:ee:ff,

and the mask is ff:ff:00:00:00:00, all MAC addresses with aa:bb:xx:xx:xx:xx result

in a match (where x is any hexadecimal number). Note that this is not a wildcard

mask, which ACLs use.

• Destination MAC. Select this radio button to require a packet’s destination MAC

address to match the specified MAC address. After you select the radio button, use

the following fields to configure the destination MAC address match criteria:

- Address. The destination MAC address to match. The destination MAC address

is specified as six two-digit hexadecimal numbers separated by colons.

- Mask. The MAC mask, which specifies the bits in the destination MAC address to

compare against an Ethernet frame. Use Fs and zeros to configure the MAC

mask. An F means that the bit is checked, and a zero in a bit position means that

the data is not significant. For example, if the MAC address is aa:bb:cc:dd:ee:ff,

and the mask is ff:ff:00:00:00:00, all MAC addresses with aa:bb:xx:xx:xx:xx result

in a match (where x is any hexadecimal number). Note that this is not a wildcard

mask, which ACLs use.

• Protocol T ype. Select this radio button to require a packet’s Layer 4 protocol to match

the specified protocol, which you must select from the menu. The menu includes

Other as a selection, which lets you enter a protocol number from 0 to 255.

• Source IP. Select this radio button to require a packet’s source IP address to match

the specified IP address. After you select the radio button, use the following fields to

configure the source IP address match criteria:

- Address. The source IP address format to match in dotted-decimal.

-Mask. The bit mask in IP dotted-decimal format indicating which parts of the

source IP address to use for matching against packet content.

•Source L4 Port. Select this radio button to require a packet’s TCP/UDP source port to

match the specified protocol, which you must select from the menu. The range is 0 to

65535. The menu includes Other as an option for unnamed ports.

• Destination IP. Select this radio button to require a packet’s destination IP address to

match the specified IP address. After you select the radio button, use the following

fields to configure the destination IP address match criteria:

- Address. The destination IP address format to match in dotted-decimal.

-Mask. The bit mask in IP dotted-decimal format indicating which parts of the

destination IP address to use for matching against packet content.

•Destination L4 Port. Select this radio button to require a packet’s TCP/UDP

destination port to match the specified protocol, which you must select from the menu.

The range is 0 to 65535. The menu includes Other as an option for unnamed ports.

• IP DSCP. Select this radio button to require the packet’s IP DiffServ Code Point

(DSCP) value to match the specified IP DSCP keyword code, which you must select

from the menu. The menu includes Other as a selection, which lets you enter an IP

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual271

DSCP value from 0 to 63. The DSCP value is defined as the high-order 6 bits of the

Service Type octet in the IP header.

• Precedence V alue. Select this radio button to require the packet’s IP precedence

value to match the specified number from 0 to 7, which you must select from the

menu. The IP Precedence field in a packet is defined as the high-order 3 bits of the

Service Type octet in the IP header.

• IP ToS. Select this radio button to require the packet’s Type of Service (ToS) bits in

the IP header to match the specified value. The IP ToS field in a packet is defined as

all 8 bits of the service type octet in the IP header. After you select the radio button,

use the following fields to configure the ToS match criteria:

- Bits V alue. Enter a two-digit hexadecimal number octet value in the range from 00

to ff to match the bits in a packet’s ToS field.

- Bit Mask. Specify the bit positions that are used for comparison against the IP

ToS field in a packet.

11. Click the Apply button.

Your settings are saved.

The following table describes the nonconfigurable information displayed in the Class

Summary section at the bottom of the DiffServ Advanced Class Configuration page.

Table 69. DiffServ Class Configuration, Class Summary information

Field Description

Match Criteria The configured match criteria for the specified class.

Values The values of the configured match criteria.

Rename an existing DiffServ class

To rename an existing DiffServ class:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > DiffServ > Advanced > Class Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual272

The Class Name page displays.

6. Select the check box next to the class name.

7. In the Class Name field, specify the new name.

8. Click the Apply button.

Your settings are saved.

Change the criteria for an existing DiffServ class

To change the criteria for an existing DiffServ class:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > DiffServ > Advanced > Class Configuration.

The Class Name page displays.

6. Click the class name, which is a hyperlink.

The page on which you can change the class configuration displays.

7. Change the class configuration as needed.

8. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual273

Delete a DiffServ class

To delete a DiffServ class:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > DiffServ > Advanced > Class Configuration.

The Class Name page displays.

6. Select the check box next to the class name.

7. Click the Delete button.

The class is removed.

Configure DiffServ IPv6 class settings

The switch supports QoS ACL and DiffServ functionality for IPv6 by providing support for

IPv6 packet classification. An IPv6 ACL serves the same purpose as an IPv4 ACL.

An Ethernet IPv6 packet is distinguished from an IPv4 packet by its unique Ethertype value,

so all IPv6 classifiers include the Ethertype field, even though you cannot configure its value

on the switch.

The destination and source IPv6 addresses use a prefix length value instead of an individual

mask to qualify them as a subnet addresses or a host addresses. Packets that match an IPv6

classifier can be marked with the IP DSCP field in the traffic class octet.

You can also assign an IPv6 ACL with a DiffServ assignment to LAG interfaces.

Create and configure an IPv6 DiffServ class

To create and configure an IPv6 DiffServ class:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual274

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > DiffServ > Advanced > IPv6 Class Configuration.

6. Enter a class name in the Class Name field.

The Class Name field also lists all the existing IPv6 class names, from which one can be

selected for modification or deletion.

7. From the Class Type menu, select the class type.

The switch supports only the class type value All, which means that all the various match

criteria defined for the class are satisfied for a packet match. All signifies the logical AND

statement of all the match criteria. You can select the class type only when you are

creating a new class. After the class is created, the Class Type field becomes

nonconfigurable.

8. Click the Add button.

The new class is added.

9. After creating the class, click the class name.

The class name is a hyperlink to the page on which you can define the class

configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual275

10. Define the criteria that must be associated the IPv6 DiffServ class:

• Match Every. Select this radio button to add a match condition that considers all

packets to belong to the class. The only selection from the Match Every menu is Any.

•Reference Class. Select this radio button to reference another class for criteria. The

match criteria defined in the reference class function as match criteria in addition to

the match criteria that you define for the selected class. After selecting this option, the

classes that can be referenced are displayed. Select the class to reference. A class

can reference at most one other class of the same type.

• Protocol T ype. Select this radio button to require a packet’s Layer 4 protocol to match

the specified protocol, which you must select from the menu. The menu includes

Other as a selection, which lets you enter a protocol number from 0 to 255.

• Source Prefix/Length. Select this radio button to require a packet’s source prefix and

prefix length to match the specified source IPv6 prefix and prefix length. Prefix must

always be specified with the prefix length. The prefix can be in the hexadecimal range

from 0 to FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF and the prefix length can

be in the range from 0 to 128.

•Source L4 Port. Select this radio button to require a packet’s TCP/UDP source port to

match the specified protocol, which you must select from the menu. The range is 0 to

65535. The menu includes Other as an option for unnamed ports.

• Destination Prefix/Length. Select this radio button to require a packet’s destination

prefix and prefix length to match the specified source IPv6 prefix and prefix length.

Prefix must always be specified with the prefix length. The prefix can be in the

hexadecimal range from 0 to FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF and

the prefix length can be in the range from 0 to 128.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual276

• Destination L4 Port. Select this radio button to require a packet’s TCP/UDP

destination port to match the specified protocol, which you must select from the menu.

The range is 0 to 65535. The menu includes Other as an option for unnamed ports.

• Flow Label. Select this radio button to require a packet’s flow label to match the

specified flow label. The flow label is a 20-bit number that is unique to an IPv6 packet

and that is used by end stations to signify QoS handling in routers. The flow label can

be specified in the range from 0 to 1048575.

• IP DSCP. Select this radio button to require the packet’s IP DiffServ Code Point

(DSCP) value to match the specified IP DSCP keyword code, which you must select

from the menu. The menu includes Other as a selection, which lets you enter an IP

DSCP value from 0 to 63. The DSCP value is defined as the high-order 6 bits of the

Service Type octet in the IP header.

11. Click the Apply button.

Your settings are saved.

The following table describes the nonconfigurable information that is displayed in the Class

Summary section.

Table 70. IPv6 DiffServ class configuration class summary

Field Description

Match Criteria The configured match criteria for the specified class.

Values The values of the configured match criteria.

Rename an existing IPv6 DiffServ class

To rename an existing IPv6 DiffServ class:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > DiffServ > Advanced > IPv6 Class Configuration.

The Class Name page displays.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual277

6. Select the check box next to the class name.

7. In the Class Name field, specify the new name.

8. Click the Apply button.

Your settings are saved.

Change the criteria for an existing IPv6 DiffServ class

To change the criteria for an existing IPv6 DiffServ class:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > DiffServ > Advanced > IPv6 Class Configuration.

The Class Name page displays.

6. Click the class name, which is a hyperlink.

The page on which you can change the class configuration displays.

7. Change the class configuration as needed.

8. Click the Apply button.

Your settings are saved.

Delete an IPv6 DiffServ class

To delete an IPv6 DiffServ class:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual278

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > DiffServ > Advanced > IPv6 Class Configuration.

The Class Name page displays.

6. Select the check box next to the class name.

7. Click the Delete button.

The class is removed.

Configure a DiffServ policy

You can associate a collection of classes with one or more policies.

Create and configure a DiffServ policy

To create and configure a DiffServ policy:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > DiffServ > Advanced > Policy Configuration.

6. Enter a policy name in the Policy Name field.

You cannot specify the policy type. By default, the policy type is In, indicating that the

policy applies to ingress packets.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual279

7. From the Member Class menu, optionally select an existing class that you want to

associate with the new policy.

8. Click the Add button.

The new policy is added.

9. After creating the policy, click the policy name.

The policy name is a hyperlink to the page on which you can define the policy attributes.

10. From the Assign Queue menu, select the queue to which packets of this policy class must

be assigned.

This is an integer value in the range 0 to 7.

11. Configure the policy attributes:

• Drop. Select this radio button to require each inbound packet to be dropped.

• Mark VLAN CoS. Select this radio button to specify the VLAN priority, which you must

select from the menu. The VLAN priority is expressed as an integer value in the range

from 0 to 7.

•Mark IP Precedence. Select this radio button to require packets to be marked with an

IP precedence value before being forwarded. You must select an IP precedence

value from 0 to 7 from the menu.

•Mirror. Select this radio button to require packets to be mirrored to an interface or

LAG, one of which you must select from the menu.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual280

• Redirect. Select this radio button to require packets to be redirected to an interface or

LAG, one of which you must select from the menu.

• Mark IP DSCP. Select this radio button to require packet to be marked with an IP

DSCP keyword code, which you must select from the menu. The menu includes

Other as a selection, which lets you enter an IP DSCP value from 0 to 63. The DSCP

value is defined as the high-order 6 bits of the Service Type octet in the IP header.

• Simple Policy. Select this radio button to define the traffic policing style for the class.

A simple policy uses a single data rate and burst size, resulting in one of two

outcomes: conform or violate. You must define the policy as described in the next

step.

12. If you select the Simple Policy radio button, you can specify the traffic policing style for the

class:

•Color Mode. From the menu, select one of the following options:

- Color Blind. This is the default selection. Color classes do not apply.

- Color Aware. Requires you to select a color class that is valid for use with this

policy instance. After you select Color Aware from the Color Mode menu, the

Color Conform Class menu displays. From this menu you must select a color

class that you already created (see Configure a DiffServ class on page 267) and

selected as a member class for this policy instance (see Step 7).

Note: A valid color class contains a single, non-excluded match criterion for

the CoS, IP DSCP, or IP Precedence option. The configured option

must not conflict with the classifier of the policy instance itself.

• Committed Rate. Enter the committed rate that is applied to conforming packets by

specifying a value in the range from 1 to 4294967295 Kbps.

• Committed Burst Size. Enter the committed burst size that is applied to conforming

packets by specifying a value in the range from 1 to 128 Kbps.

13. Select the conforming and violating actions.

The Conform Action section and Violate Action section list the actions to be taken on

conforming packets according to the policing metrics. By default, both conforming

packets and violating packets are sent.

In both the Conform Action section and the Violate Action section, select one of the

following actions:

• Send. Packets are forwarded unmodified. This is the default confirming action and the

default violating action.

•Drop. Packets are dropped.

• Mark CoS. Packets are marked by DiffServ with the specified CoS value before being

forwarded. This selection requires that the Mark CoS field is set. You must select a

CoS value from 0 to 7 from the menu.

• Mark IP Precedence. These packets are marked by DiffServ with the specified IP

Precedence value before being forwarded. This selection requires that the Mark IP

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual281

Precedence field is set. You must select an IP precedence value from 0 to 7 from the

menu.

• Mark IP DSCP. Packets are marked by DiffServ with the specified DSCP value before

being forwarded. This selection requires that the DSCP field is set. You must select a

DSCP code from the menu. The menu includes Other as a selection, which lets you

enter an IP DSCP value from 0 to 63. The DSCP value is defined as the high-order

six bits of the Service Type octet in the IP header.

14. Click the Apply button.

Your settings are saved.

The following table describes the nonconfigurable information displayed on the page.

Table 71. DiffServ policy configuration policy attribute

Field Description

Policy Name The name of the DiffServ policy.

Policy Type The type of the policy, which is always inbound (In).

Member Class Name The name of the class instance within the policy.

Rename an existing DiffServ policy

To rename an existing DiffServ policy:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > DiffServ > Advanced > Policy Configuration.

The Policy Configuration page displays.

6. Select the check box next to the policy name.

7. In the Policy Name field, specify the new name.

8. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual282

Change the policy attributes for an existing DiffServ policy

To change the policy attributes for an existing DiffServ policy:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > DiffServ > Advanced > Policy Configuration.

The Policy Configuration page displays.

6. Click the policy name, which is a hyperlink.

The page on which you can change the policy attributes displays.

7. Change the policy attributes as needed.

8. Click the Apply button.

Your settings are saved.

Change or remove a class from an existing DiffServ policy

To remove a class from an existing DiffServ policy:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual283

5. Select QoS > DiffServ > Advanced > Policy Configuration.

The Policy Configuration page displays.

6. Select the check box next to the policy name.

7. From the Member Class menu, select None.

8. Click the Apply button.

The class is removed from the policy.

Delete a DiffServ policy

To delete a DiffServ policy:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > DiffServ > Advanced > Policy Configuration.

The Policy Configuration page displays.

6. Select the check box next to the policy name.

7. Click the Delete button.

The policy is removed.

Configure the DiffServ service interface

You can assign (attach) a policy to an interface.

Attach a DiffServ policy to an interface

To attach a DiffServ policy to an interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual284

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > DiffServ > Advanced > Service Configuration.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Select the check box associated with the port, or type the port number in the Go To

Interface field and click the Go button.

8. From the Policy Name menu, select a policy name.

9. Click the Apply button.

Your settings are saved.

The following table describes the nonconfigurable information displayed on the page.

Table 72. Service Interface Configuration information

Field Description

Direction Shows the traffic direction of this service interface (either In or Out).

Operational Status Shows the operational status of this service interface (either Up or Down).

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual285

Change the DiffServ policy for an interface

To change the DiffServ policy for an interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

The Service Interface Configuration page displays.

5. Select QoS > DiffServ > Advanced > Service Configuration.

The Service Interface Configuration page displays.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1

(the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

•LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Select the check box associated with the port, or type the port number in the Go To

Interface field and click the Go button.

8. From the Policy In Name menu, select another policy name.

9. Click the Apply button.

Your settings are saved.

Remove a DiffServ policy from an interface

To remove a DiffServ policy from an interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual286

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select QoS > DiffServ > Advanced > Service Configuration.

The Service Interface Configuration page displays.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1

(the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

•LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Select the check box associated with the port, or type the port number in the Go To

Interface field and click the Go button.

8. From the Policy In Name menu, select None.

9. Click the Apply button.

Your settings are saved.

View DiffServ service statistics

You can display service-level statistical information about all interfaces to which DiffServ

policies are attached.

To view the DiffServ service statistics:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configure Quality of Service User Manual287

5. Select QoS > DiffServ > Advanced > Service Statistics.

6. Click the Update button to refresh the page with the latest information about the switch.

The following table describes the information available on the Service Statistics page.

Table 73. DiffServ Service Statistics information

Field Description

Interface All valid port numbers on the switch with a DiffServ policy that is attached in the inbound

direction.

Direction The traffic direction of interface is inbound (In). This field shows only the direction for

which a DiffServ policy is attached.

Policy Name The name of the policy that is currently attached to the specified interface and direction.

Operational Status The operational status of the policy that is attached to the specified interface and

direction. The value is either Up or Down.

Discarded Packets The total number of packets that are discarded for all class instances in this service policy

for any reason due to DiffServ treatment. This is the overall count per interface, per

direction. The discarded packets are supported in the inbound direction but not in the

outbound direction.

Member Classes All DiffServ classes that are defined as members of the selected policy name. Select a

member class name to display its statistics. If no class is associated with the selected

policy, then the list is empty.

288

6Manage Device Security

This chapter covers the following topics:

•Change the device password for the local browser interface

•Manage the RADIUS settings

•Configure the TACACS+ settings

•Configure authentication lists

•Manage the Smart Control Center Utility

•Configure management access

•Control access with profiles and rules

•Configure port authentication

•Set up traffic control

•Configure access control lists

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual289

Change the device password for the

local browser interface

You can change the device password for the user with the user name admin.

To change the device password for the local browser interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security> Management Security > User Configuration > Change Password.

6. In the Old Password field, specify the current password for the account created by the user.

The entered password is displayed in dots. Passwords are up to 20 alphanumeric

characters in length, and are case sensitive.

7. In the New Password field, specify the optional new or changed password for the account.

The entered password is displayed in dots. Passwords are up to 20 alphanumeric

characters in length, and are case sensitive.

8. In the Confirm Password field, enter the password again to confirm that you entered it

correctly.

The entered password is displayed in dots.

9. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual290

Note: If you forget the password and are unable to log in to the local browser

interface, press the Factory Defaults button on the front panel of the

switch for more than five seconds. The device reboots, and all switch

settings, including the password, are reset to the factory default

values.

Manage the RADIUS settings

RADIUS servers provide additional security for networks. The RADIUS server maintains a

user database, which contains per-user authentication information. The switch passes

information to the configured RADIUS server, which can authenticate a user name and

password before authorizing use of the network. RADIUS servers provide a centralized

authentication method for the following:

•Web access

•Access control port (802.1X)

Configure the global RADIUS server settings

You can add information about one or more RADIUS servers on the network.

If you configure multiple RADIUS servers, consider the maximum delay time when you

specify the maximum number of retransmissions (that is, the value that you enter in the Max

Number of Retransmits field) and the time-out period (that is, the value that you enter in the

Timeout Duration field) for RADIUS:

For one RADIUS server, a retransmission does not occur until the configured time-out

period expires without a response from the RADIUS server. In addition. the maximum

number of retransmissions for one RADIUS server must pass before the switch attempts

the next RADIUS server.

Therefore, the maximum delay in receiving a RADIUS response on the switch equals the

maximum number of retransmissions multiplied by the time-out period multiplied by the

number of configured RADIUS servers. If the RADIUS request was generated by a user

response.

To configure the global RADIUS server settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual291

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Management Security > RADIUS > Global Configuration.

The Current Server IP Address field is blank if no servers are configured (see Configure

a RADIUS authentication server on the switch on page 292). The switch supports up to

three RADIUS servers. If more than one RADIUS server is configured, the current server

is the server configured as the primary server. If no servers are configured as the primary

server, the current server is the most recently added RADIUS server.

CAUTION:

The maximum delay in receiving a RADIUS response on the switch equals

the maximum number of retransmissions multiplied by the time-out period

multiplied by the number of configured RADIUS servers. If the RADIUS

request was generated by a user login attempt, all user interfaces are

blocked until the switch receives a RADIUS response.

6. In the Max Number of Retransmits field, specify the maximum number of times a request

packet is retransmitted to the RADIUS server.

The range is from 1 to 15. The default value is 4.

7. In the Timeout Duration field, specify the time-out value, in seconds, for request

retransmissions.

The range is from 1 to 30. The default value is 5.

8. From he Accounting Mode menu, select to disable or enable RADIUS accounting on the

server.

The default is Disabled.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual292

9. Click the Apply button.

Your settings are saved.

The following table describes the nonconfigurable fields displayed on the page.

Table 74. RADIUS Configuration information

Field Description

Current Server Address The address of the current server. This field is blank if no servers are configured.

Number of Configured

Authentication Servers The number of configured authentication RADIUS servers. The value can range

from 0 to 32.

Configure a RADIUS authentication server on the switch

You view and configure various settings for a RADIUS server configured on the switch.

Add a primary RADIUS authentication server to the switch

To add a primary RADIUS authentication server to the switch and view or reset the

RADIUS authentication server statistics:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Management Security > RADIUS > Server Configuration.

6. In the Server Address field, specify the IP address of the RADIUS server.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual293

7. In the Authentication Port field, specify the UDP port number the server uses to verify the

RADIUS server authentication.

The valid range is from 1 to 65535. The default value is 1812.

8. From the Secret Configured menu, select Yes.

You must select Yes before you can configure the RADIUS secret. After you add the

RADIUS server, this field indicates whether the shared secret for this server was

configured.

9. In the Secret field, type the shared secret text string used for authenticating and encrypting

all RADIUS communications between the switch and the RADIUS server.

This secret must match the RADIUS encryption.

10. From the Active menu, select Primary.

11. From the Message Authenticator menu, select Enable or Disable to specify whether the

message authenticator attribute for the selected server is enabled.

The message authenticator adds protection to RADIUS messages by using an MD5 hash

to encrypt each message. The shared secret is used as the key, and if the message fails

to be verified by the RADIUS server, it is discarded.

12. Click the Add button.

The server is added to the switch.

13. Click the Apply button.

Your settings are saved.

The following table describes the RADIUS server statistics displayed on the page.

You can reset the authentication server and RADIUS statistics to their default values by

clicking the Clear Counters button.

Table 75. RADIUS authentication server statistics information

Field Description

Server Address The address of the RADIUS server or the name of the RADIUS server for

which the statistics are displayed.

Round T rip Time The time interval, in hundredths of a second, between the most recent

access-reply/access-challenge and the access-request that matched it from

this RADIUS authentication server.

Access Requests The number of RADIUS access-request packets sent to this server. This

number does not include retransmissions.

Access Retransmissions The number of RADIUS access-request packets retransmitted to this server.

Access Accepts The number of RADIUS access-accept packets, including both valid and

invalid packets, that were received from this server.

Access Rejects The number of RADIUS access-reject packets, including both valid and invalid

packets, that were received from this server.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual294

Modify the settings for a RADIUS authentication server on the switch

To modify the settings for a RADIUS authentication server on the switch:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Management Security > RADIUS > Server Configuration.

The Server Configuration page displays.

6. Select the check box next to the server IP address.

7. Modify the configuration for the selected server.

8. Click the Apply button.

Your settings are saved.

Access Challenges The number of RADIUS access-challenge packets, including both valid and

invalid packets, that were received from this server.

Malformed Access Responses The number of malformed RADIUS access-response packets received from

this server. Malformed packets include packets with an invalid length. Bad

authenticators or signature attributes or unknown types are not included in

malformed access-responses.

Bad Authenticators The number of RADIUS access-response packets containing invalid

authenticators or signature attributes received from this server.

Pending Requests The number of RADIUS access-request packets destined for this server that

did not yet time out or receive a response.

Timeouts The number of authentication time-outs to this server.

Unknown Types The number of RADIUS packets of unknown type that were received from this

server on the authentication port.

Packets Dropped The number of RADIUS packets received from this server on the

authentication port and dropped for some other reason.

Table 75. RADIUS authentication server statistics information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual295

Remove a RADIUS authentication server from the switch

To a remove a RADIUS authentication server from the switch:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Management Security > RADIUS > Server Configuration.

The Server Configuration page displays.

6. Select the check box next to the IP address of the server to remove.

7. Click the Delete button.

The RADIUS server is removed.

8. Click the Apply button.

Your settings are saved.

Configure a RADIUS accounting server

You can view and configure various settings for a RADIUS accounting server on the network.

Add a RADIUS accounting server to the switch

To add a RADIUS accounting server to the switch and view or clear the RADIUS

accounting server statistics:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual296

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Management Security > RADIUS > Accounting Server Configuration.

6. In the Accounting Server Address field, specify the IP address of the RADIUS accounting

server to add.

7. In the Port field, specify the UDP port number the server uses to verify the RADIUS

accounting server authentication. The default UDP port number is 1813.

8. From the Secret Configured menu, select Yes to add a RADIUS secret in the next field.

You must select Yes before you can configure the RADIUS secret. After you add the

RADIUS accounting server, this field indicates whether the shared secret for this server

was configured.

9. In the Secret field, type the shared secret to use with the specified accounting server.

10. From the Accounting Mode menu, select Enable to enable the RADIUS accounting mode.

11. Click the Add button.

The server is added to the switch.

12. Click the Apply button.

Your settings are saved.

The following table describes the RADIUS server statistics displayed on the page.

13. To reset the accounting server and RADIUS statistics to their default values, click the Clear

Counters button.

Table 76. RADIUS accounting server statistics information

Field Description

Accounting Server Address The accounting server associated with the statistics.

Round T rip Time (secs) The time interval, in hundredths of a second, between the most recent

accounting-response and the accounting-request that matched it from this

RADIUS accounting server.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual297

Modify the settings for a RADIUS authentication server on the switch

To modify the settings for a RADIUS accounting server on the switch:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Management Security > RADIUS > Accounting Server Configuration.

The Accounting Server Configuration page displays.

Accounting Requests The number of RADIUS accounting-request packets sent not including

retransmissions.

Accounting Retransmissions The number of RADIUS accounting-request packets retransmitted to this

RADIUS accounting server.

Accounting Responses The number of RADIUS packets received on the accounting port from this

server.

Malformed Accounting Responses The number of malformed RADIUS accounting-response packets received

from this server. Malformed packets include packets with an invalid length.

Bad authenticators and unknown types are not included as malformed

accounting responses.

Bad Authenticators The number of RADIUS accounting-response packets that contained invalid

authenticators received from this accounting server.

Pending Requests The number of RADIUS accounting-request packets sent to this server that

did not yet time out or receive a response.

Timeouts The number of accounting time-outs to this server.

Unknown Types The number of RADIUS packets of unknown type that were received from

this server on the accounting port.

Packets Dropped The number of RADIUS packets that were received from this server on the

accounting port and dropped for some other reason.

Table 76. RADIUS accounting server statistics information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual298

6. Select the check box next to the server IP address.

7. Modify the configuration for the selected accounting server.

8. Click the Apply button.

Your settings are saved.

Remove a RADIUS authentication server from the switch

To a remove a RADIUS accounting server from the switch:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Management Security > RADIUS > Accounting Server Configuration.

The Accounting Server Configuration page displays.

6. Select the check box next to the IP address of the server to remove.

7. Click the Delete button.

The RADIUS accounting server is removed.

8. Click the Apply button.

Your settings are saved.

Configure the TACACS+ settings

TACACS+ provides a centralized user management system, while still retaining consistency

with RADIUS and other authentication processes. TACACS+ provides the following services:

• Authentication. Provides authentication during login and through user names and

user-defined passwords.

• Authorization. Performed at login. When the authentication session is completed, an

authorization session starts using the authenticated user name. The TACACS+ server

checks the user privileges.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual299

The TACACS+ protocol ensures network security through encrypted protocol exchanges

between the device and TACACS+ server.

Configure the global TACACS+ settings

You can configure the global TACACS+ settings for communication between the switch and

a TACACS+ server.

To configure the global TACACS+ settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Management Security > TACACS+ > TACACS+ Configuration.

6. In the Key String field, specify the authentication and encryption key for TACACS+

communications between the switch and the TACACS+ server.

The valid range is 0–128. The key must match the key configured on the TACACS+

server.

7. In the Connection Timeout field, specify the maximum number of seconds allowed to

establish a TCP connection between the switch and the TACACS+ server.

8. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual300

Configure a TACACS+ server on the switch

You can configure up to five TACACS+ servers with which the switch can communicate.

To configure a TACACS+ server on the switch:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Management Security> TACACS+ > TACACS+ Server Configuration.

6. In the TACACS+ Server field, enter the TACACS+ server IP address.

7. In the Priority field, specify the priority for the TACACS+ server.

The priority determines the order in which the TACACS+ servers are contacted when

attempting to authenticate a user. A value of 0 is the highest priority. The valid range is

0–65535.

8. In the Port field, specify the authentication port value for TACAS+ server sessions. It must

be within the range 0–65535. If you do not specify a value, the switch uses the standard

TCP port 49 for sessions with the server.

9. In the Key String field, specify the authentication and encryption key for TACACS+

communications between the device and the TACACS+ server.

The valid range is 0–128. The key must match the key used on the TACACS+ server.

10. In the Connection Timeout field, specify the time that passes before the connection

between the device and the TACACS+ server times out.

The range is 1–30. If you do not specify a value, the switch uses a default value of 5.

11. Click the Add button.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual301

The server is added to the switch.

12. Click the Apply button.

Your settings are saved.

Modify the settings for a TACACS+ server on the switch

To modify the settings for a TACACS+ server on the switch:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Management Security> TACACS+ > TACACS+ Server Configuration.

The TACACS+ Server Configuration page displays.

6. Select the check box next to the server IP address.

7. Modify the configuration for the selected TACACS+ server.

8. Click the Apply button.

Your settings are saved.

Remove a TACACS+ server from the switch

To remove a TACACS+ server from the switch:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual302

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Management Security> TACACS+ > TACACS+ Server Configuration.

The TACACS+ Server Configuration page displays.

6. Select the check box next to the server IP address.

7. Click the Delete button.

The TACACS+ server is removed.

Configure authentication lists

A login list specifies one or more authentication methods to validate switch or port access for

the admin user. You can configure a default login list.

Note: The admin user is assigned to a preconfigured list that is named

defaultList and that you cannot delete.

Configure an HTTP authentication list

You can configure the default HTTP login list.

To change the HTTP authentication method for the default list:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual303

5. Select Security > Management Security > Authentication List > HTTP Authentication

List.

6. Select the check box next to the httpList name.

7. From the menu in the 1 column, select the authentication method that must be used first in

the selected authentication login list.

If you select a method that does not time out as the first method, such as Local, no other

method is tried, even if you specified more than one method. User authentication occurs

in the order the methods are selected. Possible methods are as follows:

• Local. The user’s locally stored ID and password are used for authentication. Since

the Local method does not time out, if you select this option as the first method, no

other method is tried, even if you specified more than one method.

• RADIUS. The user’s ID and password are authenticated using the RADIUS server. If

you select RADIUS or TACACS+ as the first method and an error occurs during the

authentication, the switch uses Method 2 to authenticate the user.

• TACACS+. The user’s ID and password are authenticated using the TACACS+

server. If you select RADIUS or TACACS+ as the first method and an error occurs

during the authentication, the switch attempts user authentication Method 2.

• None. The authentication method is unspecified. This option is available only for

Method 2 and Method 3.

8. From the menu in the 2 column, select the authentication method, if any, that must be used

second in the selected authentication login list.

This is the method that is used if the first method times out. If you select a method that

does not time out as the second method, the third method is not tried.

9. From the menu in the 3 column, select the authentication method, if any, that must be used

third in the selected authentication login list.

10. From the menu in the 4 column, select the method, if any, that must be used fourth in the

selected authentication login list.

This is the method that is used if all previous methods time out.

11. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual304

Configure an HTTPS authentication list

You can configure the default login list for secure HTTP (HTTPS).

To configure an HTTPS authentication list:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Management Security > Authentication List > HTTPS Authentication

List.

6. Select the check box next to the httpsList name.

7. From the menu in the 1 column, select the authentication method that must be used first in

the selected authentication login list.

If you select a method that does not time out as the first method, such as Local, no other

method is tried, even if you specified more than one method. This setting does not display

when you first create a new login list. User authentication occurs in the order the methods

are selected. Possible methods are as follows:

• Local. The user’s locally stored ID and password are used for authentication. Since

the Local method does not time out, if you select this option as the first method, no

other method is tried, even if you specified more than one method.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual305

• RADIUS. The user’s ID and password are authenticated using the RADIUS server. If

you select RADIUS or TACACS+ as the first method and an error occurs during the

authentication, the switch uses Method 2 to authenticate the user.

• TACACS+. The user’s ID and password are authenticated using the TACACS+

server. If you select RADIUS or TACACS+ as the first method and an error occurs

during the authentication, the switch attempts user authentication Method 2.

• None. The authentication method is unspecified. This option is only available for

Method 2 and Method 3.

8. From the menu in the 2 column, select the authentication method, if any, that must be used

second in the selected authentication login list.

This is the method that is used if the first method times out. If you select a method that

does not time out as the second method, the third method is not tried.

9. From the menu in the 3 column, select the authentication method, if any, that must be used

third in the selected authentication login list.

10. From the menu in the 4 column, select the method, if any, that must be used fourth in the

selected authentication login list.

This is the method that is used if all previous methods time out.

11. Click the Apply button.

Your settings are saved.

Configure the dot1x authentication list

The Dot1x authentication list defines the IEEE 802.1X authentication method used for the

default list. The default list is dot1xList.

To configure the dot1x authentication list:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Management Security > Authentication List > Dot1x Authentication

List.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual306

6. Select the check box next to the dot1xList name.

7. From the menu in the 1 column, select the method that must be used r first in the selected

authentication login list.

The options are as follows:

• Local. The user’s locally stored ID and password are used for authentication.

• Radius. The user’s ID and password are authenticated using the RADIUS server

instead of locally.

• None. The user is not authenticated.

8. Click the Apply button.

Your settings are saved.

Manage the Smart Control Center Utility

As a security enhancement, you can disable the Smart Control Center SCC utility. By default,

the utility is enabled and allows you to configure the switch (see Discover a switch in a

network with a DHCP server on page 14 and Discover a switch in a network without a

DHCP server on page 15).

To enable or disable the SCC administrative mode:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual307

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Management Security > SCC Control.

6. Select the one of the following SCC Admin Mode radio buttons:

• Enable. SCC can discover the switch and perform actions on the switch. This is the

default setting.

•Disable. SCC can discover the switch but cannot perform any actions on the switch.

Note: Because the switch administrator password is contained in each

NETGEAR Switch Discovery Protocol (NSDP) packet, disabling SCC

increases the switch security.

7. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual308

Configure management access

You can configure HTTP and secure HTTP access to the local browser interface. You can

also configure access control profiles and access rules.

Configure HTTP access settings

You can configure the HTTP access settings on the switch.

To configure the HTTP access settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Access > HTTP > HTTP Configuration.

6. In the HTTP Session Soft Timeout field, specify the number of minutes an HTTP session

can be idle before a time-out occurs.

The value must be in the range of 0–60 minutes. The default value is 5 minutes. The

currently configured value is shown when the web page is displayed.

After the session is inactive for the configured time, you are automatically logged out and

must reenter the password to access the local browser interface. A value of zero means

that the session does not time out.

7. In the HTTP Session Hard Timeout field, specify the hard time-out for HTTP sessions.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual309

This time-out is unaffected by the activity level of the session. The value must be in the

range of 0–168 hours. value of zero means that the session does not time out. The

default value is 24 hours.

8. In the Maximum Number of HTTP Sessions field, specify the maximum number of HTTP

sessions that can exist at the same time.

9. Click the Apply button.

Your settings are saved.

Configure HTTPS access settings

Secure HTTP enables the transmission of HTTP over an encrypted Secure Sockets Layer

(SSL) or Transport Layer Security (TLS) connection. When you manage the switch by using

the local browser interface, HTTPS can help ensure that communication between the

management system and the switch is protected from eavesdroppers and man-in-the-middle

attacks. The hash algorithms that SSL uses are MD5 and SHA-1.

To configure HTTPS access settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Access > HTTPS > HTTPS Configuration.

6. Select the HTTPS Admin Mode Enable or Disable radio button.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual310

This enables or disables the administrative mode of secure HTTP (HTTPS). The

configured value is displayed. The default value is Disable. You can download SSL

certificates only when the HTTPS admin mode is disabled. HTTPS admin mode can be

enabled only if a certificate is present on the device.

7. Select the SSL Version 3 Enable or Disable radio button.

This enables or disables Secure Sockets Layer version 3.0. The configured value is

displayed. The default value is Enable.

8. Select the TLS Version 1 Enable or Disable radio button.

This enables or disables Transport Layer Security (TLS) version 1.0 and TLS version 1.2.

The configured value is displayed. The default value is Enable.

9. In the HTTPS Port field, type the HTTPS port number.

The value must be in the range of 1025 to 65535. Port 443 is the default value. The

configured value is displayed.

10. In the HTTPS Session Soft Timeout (Minutes) field, enter the inactivity time-out for HTTPS

sessions.

The value must be in the range of 1 to 60 minutes. The default value is 5 minutes. The

configured value is displayed.

11. In the HTTPS Session Hard Timeout (Hours) field, set the hard time-out for HTTPS

sessions.

This time-out is unaffected by the activity level of the session. The value must be in the

range of 1 to 168 hours. The default value is 24 hours.

12. In the Maximum Number of HTTPS Sessions field, enter the maximum allowable number

of HTTPS sessions.

The value must be in the range of 0 to 4. The default value is 4.

13. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual311

Manage certificates for HTTPS access

You can manage certificates for HTTPS access.

Generate an SSL certificate

Note: Before you can generate a certificate, you must disable HTTPS (see

Configure HTTPS access settings on page 309) and log back in to

the local browser interface over an HTTP session. After you generate

the certificate, you can reenable HTTPS and log back in to the local

browser interface over an HTTPS session.

To generate an SSL certificate:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Access > HTTPS > Certificate Management.

The Certificate Present field displays whether a certificate is present on the switch.

6. In the Certificate Management section, select the Generate Certificates radio button.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual312

7. Click the Apply button.

The switch generates an SSL certificate.

The Certificate Generation Status field shows information about the progress.

Delete an SSL certificate

Note: Before you can delete a certificate, you must disable HTTPS (see

Configure HTTPS access settings on page 309) and log back in to the

local browser interface over an HTTP session. After you delete the

certificate, you can reenable HTTPS and log back in to the local

browser interface over an HTTPS session.

To delete an SSL certificate:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Access > HTTPS > Certificate Management.

6. The Certificate Management page displays.

The Certificate Present field displays Yes.

7. In the Certificate Management section, select Delete Certificates radio button.

8. Click the Apply button.

The certificate is removed.

Transfer an existing certificate to the switch

You can transfer a certificate file to the switch.

For the web server on the switch to accept HTTPS connections from a management station,

the web server needs a public key certificate. You can generate a certificate externally (for

example, offline) and download it to the switch.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual313

Before you download a file to the switch, the following conditions must be true:

•The file to download from the TFTP server is on the server in the appropriate directory.

•The file is in the correct format.

•The switch contains a path to the TFTP server.

Note: Before you can transfer a certificate, you must disable HTTPS (see

Configure HTTPS access settings on page 309) and log back in to

the local browser interface over an HTTP session. After you transfer

the certificate, you can reenable HTTPS and log back in to the local

browser interface over an HTTPS session.

To configure the certificate transfer settings for HTTPS sessions:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Access > HTTPS > Certificate Download.

6. From the File Type menu, select the type of SSL certificate to download, which can be one

of the following:

• SSL T rusted Root Certificate PEM File. SSL Trusted Root Certificate file (PEM

Encoded)

•SSL Server Certificate PEM File. SSL Server Certificate File (PEM Encoded)

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual314

• SSL DH Weak Encryption Parameter PEM File. SSL Diffie-Hellman W eak Encryption

Parameter file (PEM Encoded)

• SSL DH Strong Encryption Parameter PEM File. SSL Diffie-Hellman Strong

Encryption Parameter File (PEM Encoded)

7. From the Server Address Type menu, select IPv4, IPv6, or DNS to indicate the format of

the TFTP/SFTP/SCP Server Address field.

The default is IPv4.

8. In the TFTP Server IP field, specify the address of the TFTP server.

The address can be an IP address in standard x.x.x.x format or a host name. The host

name must start with a letter of the alphabet. Make sure that the software image or other

file to be downloaded is available on the TFTP server.

9. In the Remote File Path field, enter the path of the file to download.

You can enter up to 96 characters. The default is blank.

10. In the Remote File Name field, enter the name of the file on the TFTP server to download.

You can enter up to 32 characters. The default is blank.

11. Select the Start File Transfer check box.

12. Click the Apply button.

The file transfer starts. A status message displays during the transfer and upon

successful completion of the transfer.

Control access with profiles and rules

Access control allows you to configure an access control profile and set rules for access to

the local browser interface, access by SNMP stations, and client access to a TFTP server.

We refer to an access control profile as an access profile. You can add a single access

profile, which you can configure, activate, or deactivate.

CAUTION:

If you configure a security access profile incorrectly and you activate the

access profile, you might no longer be able to access the switch’s local

browser interface. If that situation occurs, you must reset the switch to

factory default settings (see Reset the switch to its factory default settings

on page 422).

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual315

Add an access profile

You can set up a single security access profile with which you can associate an access rule

configuration.

To add an access profile

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Access > Access Control > Access Profile Configuration.

6. In the Access Profile Name field, enter the name of the access profile to be added.

The maximum length is 32 characters.

7. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual316

Add a rule to the access profile

After you add the access profile, you can add one or more security access rules to the access

profile.

If you access the switch from a computer, make sure that you add a permit rule for the type of

service that you use (for example, HTTPS), your computer’ s IP address, and your computer’s

subnet mask.

CAUTION:

You must add a permit rule for your device and access method, otherwise

you are locked out from the switch after you activate the access profile. If

that situation occurs, you must reset the switch to factory default settings

(see Reset the switch to its factory default settings on page 422).

To add a rule to the access profile:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Access > Access Control > Access Rule Configuration.

6. From the Rule Type menu, select Permit or Deny to permit or deny access when the

selected rules are matched.

A Permit rule allows access from a device that matches the rule criteria. A Deny rule

blocks a device that matches the rule criteria.

7. From the Service Type menu, select the access method to which the rule is applied.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual317

The policy is restricted by the selected access method. Possible access methods are

HTTP, Secure HTTP (SSL), and SNMP.

8. In the Source IP Address field, enter the source IP address from which the management

traffic originates.

9. In the Mask field, specify the subnet mask from which the management traffic originates.

10. In the Priority field, assign a priority to the rule.

The rules are validated against the incoming management request in ascending order of

their priorities. If a rule matches, the action is performed and subsequent rules below that

rule are ignored. For example, if a source IP address 10.10.10.10 is configured with

priority 1 to permit, and the same source IP address 10.10.10.10 is also configured with

priority 2 to deny, then access is permitted if the profile is active, and the second rule is

ignored.

11. Click the Add button.

The access rule is added.

Activate the access profile

After you add rules to the access profile, you can activate the access profile.

CAUTION:

If you configure a security access profile incorrectly and you activate the

access profile, you might no longer be able to access the switch’s local

browser interface. If that situation occurs, you must reset the switch to

factory default settings (see Reset the switch to its factory default settings

on page 422).

To activate the access profile:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual318

5. Select Security > Access > Access Control > Access Profile Configuration.

The Access Profile Configuration page displays. The Deactivate Profile check box is

selected.

6. Select the Activate Profile check box.

7. Click the Apply button.

Your settings are saved and the access profile is now active.

Display the access profile summary and the number of

filtered packets

After you added rules to the active profile, you can view the entries in the summary. If the

access profile is active, you can also view the number of filtered packets.

To display the access profile summary and the number of filtered packets:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Access > Access Control > Access Profile Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual319

The Packets Filtered field displays the number of packets filtered (none in the previous

figure).

6. To refresh the page with the latest information about the switch, click the Update button.

The following table describes the nonconfigurable data that is displayed.

Table 77. Access profile configuration profile summary

Field Description

Rule Type The action performed when the rules are matched.

Service Type The service type chosen. The policy is restricted by the service type chosen.

Source IP Address The source IP address of the client originating the management traffic.

Mask The subnet mask of the IP Address.

Priority The priority of the rule.

Deactivate an access profile

You can deactivate an access profile.

To deactivate an access profile:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Access > Access Control > Access Profile Configuration.

The Access Profile Configuration page displays. The Activate Profile check box is

selected.

6. Select the Deactivate Profile check box.

7. Click the Apply button.

Your settings are saved and the access profile is now deactivated.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual320

Remove an access profile

You can remove an access profile that you no longer need. Before you can remove the

access profile, you must deactivate it (see Deactivate an access profile on page 319).

To remove an access profile:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Access > Access Control > Access Profile Configuration.

The Access Profile Configuration page displays. The Deactivate Profile check box is

selected.

6. Select the Remove Profile check box.

7. Click the Apply button.

The access profile is removed.

Configure port authentication

With port-based authentication, when 802.1X is enabled globally and on the port, successful

authentication of any one supplicant attached to the port results in all users being able to use

the port without restrictions. At any given time, only one supplicant is allowed to attempt

authentication on a port in this mode. Ports in this mode are under bidirectional control. This

is the default authentication mode.

An 802.1X network includes three components:

• Authenticators. The port that is authenticated before system access is permitted.

•Supplicants. The host connected to the authenticated port requesting access to the

system services.

•Authentication Server. The external server, for example, the RADIUS server that

performs the authentication on behalf of the authenticator , and indicates whether the user

is authorized to access system services.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual321

Configure the global 802.1X settings

You can configure the global port access control settings on the switch.

To globally enable the 802.1X features:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Port Authentication > Basic > 802.1X Configuration.

6. Select the Port Based Authentication State Enable radio button.

This enables the 802.1X administrative mode on the switch. The default value is Disable.

Note: If 802.1X is enabled, authentication is performed by a RADIUS server.

This means that the primary authentication method must be RADIUS.

To set the method, select Security > Management Security >

Authentication List and select RADIUS as method 1 for defaultList.

For more information, see Configure authentication lists on

page 302.

When port-based authentication is globally disabled, the switch does not check for

802.1X authentication before allowing traffic on any ports, even if the ports are configured

to allow only authenticated users.

7. Select the VLAN Assignment Mode Enable radio button.

The default value is Disable.

When enabled, this feature allows a port to be placed into a particular VLAN based on the

result of the authentication or type of 802.1X authentication a client uses when it

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual322

accesses the device. The authentication server can provide information to the device

about which VLAN to assign the supplicant.

8. Select the Dynamic VLAN Creation Mode Enable radio button.

The default value is Disable.

If RADIUS-assigned VLANs are enabled, the RADIUS server is expected to include the

VLAN ID in the 802.1X tunnel attributes of its response message to the device. If dynamic

VLAN creation is enabled on the device and the RADIUS-assigned VLAN does not exist,

then the assigned VLAN is dynamically created. This implies that the client can connect

from any port and can get assigned to the appropriate VLAN. This feature gives flexibility

for clients to move around the network without much additional configuration required.

9. Select the EAPOL Flood Mode Enable radio button.

The default value is Disable. Extensible Authentication Protocol (EAP) over LAN (EAPoL)

flood support is enabled on the switch.

10. Click the Apply button.

Your settings are saved.

Manage port authentication on individual ports

You can enable and configure port access control on one or more physical ports.

Configure 802.1X settings for a port

To configure 802.1X settings for a port:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Port Authentication > Advanced > Port Authentication.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual323

The previous figure shows only part of the page.

6. Use the horizontal scroll bar at the bottom of the page to view all the fields.

7. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8. Specify the following settings:

•Port Control. Defines the port authorization state. The control mode is set only if the

link status of the port is link up. Select one of the following options:

- Auto. The switch automatically detects the mode of the interface.

- Authorized. The switch places the interface into an authorized state without

being authenticated. The interface sends and receives normal traf fic without client

port-based authentication.

- Unauthorized. The switch denies the selected interface system access by

moving the interface into unauthorized state. The switch cannot provide

authentication services to the client through the interface.

-MAC based. This mode allows multiple supplicants connected to the same port to

each authenticate individually. Each host connected to the port must authenticate

separately in order to gain access to the network. The hosts are distinguished by

their MAC addresses.

• Guest VLAN ID. Specify the VLAN ID for the guest VLAN. The valid range is 0–4093.

The default value is 0. Enter 0 to reset the guest VLAN ID on the interface. The guest

VLAN allows the port to provide a distinguished service to unauthenticated users,

after three authentication failures. This feature provides a mechanism to allow users

access to hosts on the guest VLAN.

• Guest VLAN Period. Specify the number of seconds that the selected port remains

in the quiet state following a failed authentication exchange. The guest VLAN time-out

must be a value in the range of 1–300. The default value is 90.

•Unauthenticated VLAN ID. Specify the VLAN ID of the unauthenticated VLAN for the

selected port. The valid range is 0–3965. The default value is 0. Hosts that fail the

authentication might be denied access to the network or placed on a VLAN created

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual324

for unauthenticated clients. This VLAN might be configured with limited network

access.

• Periodic Reauthentication. Select Enable to allow periodic reauthentication of the

supplicant for the specified port.

• Reauthentication Period. Specify the time, in seconds, after which reauthentication

of the supplicant occurs. The reauthentication period must be a value in the range of

1–65535. The default value is 3600. If this field is disabled, connected clients are not

forced to reauthenticate periodically.

• Quiet Period. Specify the number of seconds that the port remains in the quiet state

following a failed authentication exchange. While in the quite state, the port does not

attempt to acquire a supplicant.

• Resending EAP. Specify the EAP retransmit period for the selected port. The

transmit period is the value, in seconds, after which an EAPoL EAP Request/Identify

frame is resent to the supplicant.

• Max EAP Requests. Specify the maximum number of EAP requests for the selected

port. The value is the maximum number of times an EAPoL EAP Request/Identity

message is retransmitted before the supplicant times out.

•Supplicant Timeout. Specify the supplicant time-out for the selected port. The

supplicant time-out is the value, in seconds, after which the supplicant times out.

•Server Timeout. Specify the time that elapses before the switch resends a request to

the authentication server.

9. Click the Apply button.

Your settings are saved.

The following table describes the port authentication status information available on the

page.

Table 78. Port authentication status information

Field Description

Control Direction The control direction for the specified port, which is always Both. The control

direction dictates the degree to which protocol exchanges take place between

supplicant and authenticator .The unauthorized controlled port exerts control over

communication in both directions (disabling both incoming and outgoing frames).

Protocol Version The protocol version associated with the selected port. The only possible value

is 1, corresponding to the first version of the 802.1X specification.

PAE Capabilities The port access entity (PAE) functionality of the selected port. Possible values

are Authenticator or Supplicant.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual325

Initialize 802.1X on a port

To initialize 802.1X on a port:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Port Authentication > Advanced > Port Authentication.

The Port Authentication page displays.

6. Select the check box associated with the port to initialize.

Authenticator PAE State The current state of the authenticator PAE state machine. Possible values are as

follows:

Initialize

Disconnected

Connecting

Authenticating

Authenticated

Aborting

Held

ForceAuthorized

ForceUnauthorized

Backend State The current state of the backend authentication state machine. Possible values

are as follows:

Request

Response

Success

Fail

Timeout

Initialize

Idle

Table 78. Port authentication status information (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual326

7. Click the Initialize button.

802.1X on the selected interface is reset to the initialization state. Traffic sent to and from

the port is blocked during the authentication process. This button is available only if the

control mode is auto. When you click this button, the action is immediate. You do not

need to click the Apply button for the action to occur.

Restart the 802.1X authentication process on a port

To restart the 802.1X authentication process on a port:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Port Authentication > Advanced > Port Authentication.

The Port Authentication page displays.

6. Select the check box associated with the port to reauthenticate.

7. Click the Reauthenticate button.

The selected port is forced to restart the authentication process.This button is available only

if the control mode is auto. If the button is not selectable, it is grayed out. When you click

this button, the action is immediate. You do not need to click the Apply button for the

action to occur.

View the port summary

You can view summary information about the port-based authentication settings for each

port.

To view the port summary:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual327

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Port Authentication > Advanced > Port Summary.

The following table describes the fields on the Port Summary page.

Table 79. Port summary

Field Description

Port The port whose settings are displayed in the current table row.

Control Mode This field indicates the configured control mode for the port. Possible values are as

follows:

• Force Unauthorized. The authenticator port access entity (PAE)

unconditionally sets the controlled port to unauthorized.

• Force

Authorized. The authenticator PAE unconditionally sets the controlled

port to authorized.

• Auto. The authenticator PAE sets the controlled port mode to reflect the

outcome of the authentication exchanges between the supplicant,

authenticator, and the authentication server.

• MAC Based. The authenticator PAE sets the controlled port mode to reflect the

outcome of authentication exchanges between a supplicant, an authenticator,

and an authentication server on a per supplicant basis.

Operating Control Mode The control mode under which the port is actually operating. Possible values are as

follows:

• ForceUnauthorized

• ForceAuthorized

• Auto

• MAC Based

• N/A: If the port is in detached state, it cannot participate in port access control.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual328

View the client summary

You can display information about supplicant devices that are connected to the local

authenticator ports. If no active 802.1X sessions exist, the table is empty.

To view the client summary:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Port Authentication > Advanced > Client Summary.

Reauthentication Enabled This field shows whether reauthentication of the supplicant for the specified port is

allowed. The possible values are True and False. If the value is True,

reauthentication occurs. Otherwise, reauthentication is not allowed.

Port Status The authorization status of the specified port. The possible values are Authorized,

Unauthorized, and N/A. If the port is in detached state, the value is N/A because the

port cannot participate in port access control.

Table 79. Port summary (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual329

The following table describes the fields on the Client Summary page.

Table 80. Client Summary information

Field Description

Port The port to be displayed.

User Name The user name representing the identity of the supplicant device.

Supplicant Mac Address The supplicant’s device MAC address.

Session T ime The time since the supplicant logged in seconds.

Filter ID The policy filter ID assigned by the authenticator to the supplicant device.

VLAN ID The VLAN ID assigned by the authenticator to the supplicant device.

VLAN Assigned The reason for the VLAN ID assigned by the authenticator to the supplicant device.

Session T imeout The session time-out imposed by the RADIUS server on the supplicant device.

Termination Action The termination action imposed by the RADIUS server on the supplicant device.

Set up traffic control

You can configure MAC filters, storm control, port security, protected ports, and private VLAN

settings.

Manage MAC filtering

You can create MAC filters that limit the traffic allowed into and out of specified ports on the

switch.

Create a MAC filter

To create a MAC filter:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual330

The default password is password.

The System Information page displays.

5. Select Security > Traffic Control > MAC Filter > MAC Filter Configuration.

6. From the MAC Filter menu, select Create Filter.

If you did not configure any filters, this is the only option available.

7. From the VLAN ID menu, select the VLAN that must be used with the MAC address.

8. In the MAC Address field, specify the MAC address of the filter in the format

XX:XX:XX:XX:XX:XX.

You cannot define filters for the following MAC addresses:

•00:00:00:00:00:00

•01:80:C2:00:00:00 to 01:80:C2:00:00:0F

•01:80:C2:00:00:20 to 01:80:C2:00:00:21

•FF:FF:FF:FF:FF:FF

9. In the Port and LAG tables in the Source Port Members section, select the ports and LAGs

that must be included in the inbound filter.

If a packet with the MAC address and VLAN ID that you specify is received on a port that

is not part of the inbound filter, the packet is dropped.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual331

10. In the Port and LAG tables in the Destination Port Members section, select the ports and

LAGs that must be included in the outbound filter.

A packet with the MAC address and VLAN ID that you specify can be transmitted only

from a port that is part of the outbound filter.

Note: Destination ports can be included only in a multicast filter.

11. Click the Apply button.

Your settings are saved.

Delete a MAC filter

To delete a MAC filter:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Traffic Control > MAC Filter > MAC Filter Configuration.

The MAC Filter Configuration page displays.

6. From the MAC Filter menu, select the filter.

7. Click the Delete button.

The filter is removed.

View the MAC filter summary

You can view the MAC filters that are configured on the switch.

To view the MAC filter summary:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual332

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Traffic Control > MAC Filter > MAC Filter Summary.

The following table describes the information displayed on the page.

Table 81. MAC Filter Summary information

Field Description

MAC Address The MAC address of the filter in the format XX:XX:XX:XX:XX:XX.

VLAN ID The VLAN ID used with the MAC address to fully identify packets you want filtered.

Source Port Members The ports to be used for filtering inbound packets.

Destination Port Members The ports to be used for filtering outbound packets.

Configure storm control settings

A broadcast storm is the result of an excessive number of broadcast messages

simultaneously transmitted across a network by a single port. Forwarded message

responses can overload network resources, cause the network to time out, or do both.

The switch measures the incoming packet rate per port for broadcast, multicast, unknown,

and unicast packets and discards packets if the rate exceeds the defined value. You enable

storm control per interface, by defining the packet type and the rate at which the packets are

transmitted.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual333

Configure global storm control settings

The global storm control settings apply to all ports. After you configure the global settings,

you can specify storm control settings for one or more ports.

To configure global storm control settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Traffic Control > Storm Control.

6. In the Port Settings section, select one or more interfaces by taking one of the following

actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual334

7. In the Storm Control section, from the Ingress Control Mode menu, select the mode of

broadcast affected by storm control:

• Disabled. Storm control is disabled. This is the default setting.

•Unknown Unicast. If the rate of incoming unknown Layer 2 unicast traffic (that is,

traffic for which a destination lookup failure occurs) increases beyond the configured

threshold on an interface, the traffic is dropped.

• Multicast. If the rate of incoming Layer 2 multicast traffic increases beyond the

configured threshold on an interface, the traffic is dropped.

• Broadcast. If the rate of incoming Layer 2 broadcast traffic increases beyond the

configured threshold on an interface, the traffic is dropped.

8. If the selection from the Ingress Control Mode menu is not Disabled, specify whether the

ingress control mode is enabled by selecting Enable or Disable from the Status menu.

9. In the Threshold field, specify the maximum rate at which unknown packets are forwarded.

The range is a percent of the total threshold between 0–100%. The default is 5%.

10. From the Control Action mode menu, select one of the following options:

• None. This is the default setting.

•Trap. If the threshold of the configured broadcast storm is exceeded, a trap is sent.

• Shutdown. If the threshold of the configured broadcast storm is exceeded, the port is

shut down.

11. Click the Apply button.

Your settings are saved.

Configure storm control settings for one or more ports

After you configure the global settings, you can specify storm control settings for one or more

ports.

To configure storm control settings for one or more ports:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual335

5. Select Security > Traffic Control > Storm Control.

The default settings in the Port Settings section depends on the global storm control

settings (see Configure global storm control settings on page 333), which apply to all

ports.

6. In the Port Settings section, select one or more interfaces by taking one of the following

actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

7. From the Status menu, specify whether the ingress control mode is enabled for the port by

selecting Enable or Disable.

8. In the Threshold field, specify the maximum rate at which unknown packets are forwarded

for the port.

The range is a percent of the total threshold between 0 and 100%.

9. From the Control Action mode menu, select one of the following options for the port:

• None. No action is taken.

• Trap. If the threshold of the configured broadcast storm is exceeded, a trap is sent.

• Shutdown. If the threshold of the configured broadcast storm is exceeded, the port is

shut down.

10. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual336

Manage port security

Port security lets you lock one or more ports on the switch. When a port is locked, the port

can only forward packets with a source MAC addresses that you specifically allowed. The

port discards all other packets.

Configure the global port security mode

To configure the global port security mode:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Traffic Control > Port Security > Port Security Configuration.

6. To enable port security on the switch, select the Port Security Mode Enable radio button.

The default is Disable.

7. Click the Apply button.

Your settings are saved.

8. Click the Update button to refresh the page with the latest information about the switch.

The Port Security Violations table shows information about violations that occurred on ports

that are enabled for port security.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual337

The following table describes the fields in the Port Security Violations table.

Table 82. Port Security Violations information

Field Description

Port The physical interface.

Last Violation MAC The source MAC address of the last packet that was discarded at a locked port.

VLAN ID The VLAN ID corresponding to the last MAC address violation.

Configure a port security interface

A MAC address can be defined as allowable by one of two methods: dynamically or statically.

Both methods are used concurrently when a port is locked.

Dynamic locking implements a first arrival mechanism for port security. You specify how

many addresses can be learned on the locked port. If the limit was not reached, then a

packet with an unknown source MAC address is learned and forwarded normally. When the

limit is reached, no more addresses are learned on the port. Any packets with source MAC

addresses that were not already learned are discarded. You can effectively disable dynamic

locking by setting the number of allowable dynamic entries to zero.

Static locking allows you to specify a list of MAC addresses that are allowed on a port. The

behavior of packets is the same as for dynamic locking: only packets with an allowable

source MAC address can be forwarded.

To configure a port security interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Traffic Control > Port Security > Interface Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual338

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8. Specify the following settings:

•Port Security. Enable or disable the port security feature for the selected interfaces

The default is Disable.

• Max Learned MAC Address. Specify the maximum number of dynamically learned

MAC addresses on the selected interfaces.

• Max Static MAC Address. Specify the maximum number of statically locked MAC

addresses on the selected interfaces.

• Enable Violation Shutdown. Enable or disable shutdown of the selected interfaces if

a packet with a disallowed MAC address is received. The default value is No, which

means that the option is disabled.

• Enable Violation Traps. Enable or disable the sending of new violation traps if a

packet with a disallowed MAC address is received. The default value is No, which

means that the option is disabled.

9. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual339

View learned MAC addresses and convert them to static MAC addresses

After you enabled port security globally (see Configure the global port security mode on

page 336) and enabled port security for specific interfaces (see Configure a port security

interface on page 337), you can convert a dynamically learned MAC address to a statically

locked address.

To view learned MAC addresses for an individual interface or LAG and convert these

MAC addresses to static MAC addresses:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Traffic Control > Port Security > Security MAC Address.

6. From the Port List menu, select the individual interface.

The Dynamic MAC Address Table displays the MAC addresses and their associated

VLANs that were learned on the selected port.

Field Description

VLAN ID The VLAN ID corresponding to the MAC address.

MAC Address The MAC addresses learned on a specific port.

7. To convert the dynamically learned MAC address to a statically locked addresses, select the

Convert Dynamic Address to Static check box.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual340

8. Click the Apply button.

The dynamic MAC address entries are converted to static MAC address entries in a

numerically ascending order until the static limit is reached.

The Number of Dynamic MAC Addresses Learned field displays the number of

dynamically learned MAC addresses on a specific port.

9. To refresh the page with the latest information about the switch, click the Update button.

Configure protected ports

If a port is configured as protected, it does not forward traffic to any other protected port on

the switch, but it does forward traffic to unprotected ports. You can configure the ports as

protected or unprotected.

To configure protected ports:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Traffic Control > Protected Port.

6. In the Ports table, click each port that you want to configure as a protected port.

Protected ports are marked with a check mark. No traffic forwarding is possible between

two protected ports.

7. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual341

Manage private VLANs

A private VLAN contains switch ports that cannot communicate with each other, but can

access another network. These ports are called private ports. Each private VLAN contains

one or more private ports and a single uplink port or uplink aggregation group. Note that all

traffic between private ports is blocked at all layers, not just Layer 2 traffic, but also traffic

such as FTP, HTTP, and Telnet.

Configure a private VLAN

To configure a private VLAN:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Traffic Control > Private VLAN > Private VLAN Type Configuration.

6. Select the check box that is associated with the VLAN ID that you want to configure.

7. From the Private VLAN Type menu, select the type of private VLAN. Possible values are

as follows:

• Primary. Sets the private VLAN type as primary.

• Isolated. Sets the private VLAN type as isolated.

• Community. Sets the private VLAN type as community.

• Unconfigured. Sets the private VLAN type as unconfigured. The default is

Unconfigured.

8. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual342

Configure private VLAN associations

To configure private VLAN associations:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Traffic Control > Private VLAN > Private VLAN Association

Configuration.

6. From the Primary VLAN menu, select the primary VLAN ID of the domain.

7. In the Secondary VLAN(s) field, enter the VLAN that you want to associate with the primary

VLAN.

8. Click the Apply button.

Your settings are saved.

The following table describes the nonconfigurable information displayed on the page.

Table 83. Private VLAN Association information

Field Description

Isolated VLAN The isolated VLAN associated with the selected primary VLAN.

Community VLAN(s) The list of community VLANs associated with the selected primary VLAN.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual343

Configure the private VLAN port mode

To configure the private VLAN port mode:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Traffic Control > Private VLAN > Private VLAN Port Mode

Configuration.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual344

8. From the Port VLAN Mode menu, select the switch port mode:

• General. Sets the interfaces in general mode, which is the default selection.

• Host. Sets the interfaces in host mode, which is used for private VLAN configurations.

• Promiscuous. Sets the interfaces in promiscuous mode, which is used for private

VLAN configurations.

9. Click the Apply button.

Your settings are saved.

Configure a private VLAN host interface

To configure a private VLAN host interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Traffic Control > Private VLAN > Private VLAN Host Interface

Configuration.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual345

7. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8. In the Host Primary VLAN field, enter the primary VLAN ID for the host association mode.

The range of the VLAN ID is 2–4093.

9. In the Host Secondary VLAN field, enter the secondary VLAN ID for host association

mode.

The range of the VLAN ID is 2–4093.

10. Click the Apply button.

Your settings are saved.

The Operational VLAN(s) field displays the operational VLANs.

Configure a private VLAN promiscuous interface

To configure a private VLAN promiscuous interface:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > Traffic Control > Private VLAN > Private VLAN Promiscuous

Interface Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual346

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

• LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

•To configure all interfaces with the same settings, select the check box in the heading

row.

8. In the Promiscuous Primary VLAN field, enter the primary VLAN ID for the promiscuous

association mode.

The range of the VLAN ID is 2–4093.

9. In the Promiscuous Secondary VLAN(s) field, enter the secondary VLAN ID for

promiscuous association mode.

This field can accept single a VLAN ID, a range of VLAN IDs, or a combination of both in

sequence separated by a comma. You can specify an individual VLAN ID, such as 10.

You can specify the VLAN range values separated by a hyphen, for example, 10-13. You

can specify the combination of both separated by commas, for example,

12,15,40-43,1000-1005, 2000. The range of VLAN IDs is 2–4093.

Note: The VLAN ID list that you specify replaces the configured secondary

VLAN list in the association.

10. Click the Apply button.

Your settings are saved.

The Operational VLAN(s) field displays the operational VLANs.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual347

Configure access control lists

Access control lists (ACLs) ensure that only authorized users can access specific resources

while blocking off any unwarranted attempts to reach network resources. ACLs are used to

provide traffic flow control, restrict contents of routing updates, decide which types of traffic

are forwarded or blocked, and above all provide security for the network. The switch’s

software supports IPv4, IPv6, and MAC ACLs.

To configure an ACL:

1. Create an IPv4-based or IPv6-based or MAC-based ACL ID.

2. Create a rule and assign it to a unique ACL ID.

3. Define the rules, which can identify protocols, source, and destination IP and MAC

addresses, and other packet-matching criteria.

4. Use the ID number to assign the ACL to a port or to a LAG.

To view ACL configuration examples, see Access control lists (ACLs) on page 451.

Use the ACL Wizard to create a simple ACL

The ACL Wizard helps you create a simple ACL and apply it to the selected ports easily and

quickly. First, select an ACL type to use when you create an ACL. Then add an ACL rule to

this ACL and apply this ACL on the selected ports.

Note: The steps in the following procedure describe how you can create an

ACL based on the destination MAC address. If you select a different

type of ACL (or example, an ACL based on a source IPv4), the page

displays different information.

Use the ACL Wizard to create an ACL

To use the ACL Wizard to create an ACL:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual348

The default password is password.

The System Information page displays.

5. Select Security > ACL > ACL Wizard.

6. From the ACL Type menu, select the type of ACL.

You can select from the following ACL types:

• ACL Based on Destination MAC. Creates an ACL based on the destination MAC

address, destination MAC mask, and VLAN.

• ACL Based on Source MAC. Creates an ACL based on the source MAC address,

source MAC mask, and VLAN.

• ACL Based on Destination IPv4. Creates an ACL based on the destination IPv4

address and IPv4 address mask.

• ACL Based on Source IPv4. Creates an ACL based on the source IPv4 address and

IPv4 address mask.

• ACL Based on Destination IPv6. Creates an ACL based on the destination IPv6

prefix and IPv6 prefix length.

• ACL Based on Source IPv6. Creates an ACL based on the source IPv6 prefix and

IPv6 prefix length.

• ACL Based on Destination IPv4 L4 Port. Creates an ACL based on the destination

IPv4 Layer 4 port number.

•ACL Based on Source IPv4 L4 Port. Creates an ACL based on the source IPv4

Layer 4 port number.

•ACL Based on Destination IPv6 L4 Port. Creates an ACL based on the destination

IPv6 Layer 4 port number.

•ACL Based on Source IPv6 L4 Port. Creates an ACL based on the source IPv6

Layer 4 port number.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual349

Note: For L4 port options, two rules are created (one for TCP and one for

UDP).

7. In the Sequence Number field, enter a whole number in the range of 1 to 2147483647 that

is used to identify the rule.

8. From the Action menu, select Permit or Deny to specify the action that must be taken if a

packet matches the rule’s criteria.

9. From the Match Every menu, select one of the following options:

• False. Signifies that packets do not need to match the selected ACL and rule. With

this selection, you can add a destination MAC address, destination MAC mask, and

VLAN.

•True. Signifies that all packets must match the selected ACL and rule and are either

permitted or denied. In this case, since all packets match the rule, the option of

configuring other match criteria is not offered.

10. Specify the additional match criteria for the selected ACL type.

The rest of the rule match criteria fields available for configuration depend on the selected

ACL type. For information about the possible match criteria fields, see the following table.

ACL Based On Fields

Destination MAC • Destination MAC. Specify the destination MAC address to compare against

an Ethernet frame. The valid format is xx:xx:xx:xx:xx:xx. The BPDU keyword

might be specified using a destination MAC address of 01:80:C2:xx:xx:xx.

• Destination MAC Mask. Specify the destination MAC address mask, which

represents the bits in the destination MAC address to compare against an

Ethernet frame. The valid format is xx:xx:xx:xx:xx:xx. The BPDU keyword

might be specified using a destination MAC mask of 00:00:00:ff:ff:ff.

• VLAN. Specify the VLAN ID to match within the Ethernet frame.

Source MAC • Source MAC. Specify the source MAC address to compare against an

Ethernet frame. The valid format is xx:xx:xx:xx:xx:xx.

• Source MAC Mask. Specify the source MAC address mask, which

represents the bits in the source MAC address to compare against an

Ethernet frame. The valid format is (xx:xx:xx:xx:xx:xx).

• VLAN. Specify the VLAN ID to match within the Ethernet frame.

Destination IPv4 • Destination IP Address. Specify the destination IP address.

• Destination IP Mask. Specify the destination IP address mask.

Source IPv4 • Source IP Address. Specify the source IP address.

• Source IP Mask. Specify the source IP address mask.

Destination IPv6 • Destination Prefix. Specify the destination prefix.

• Destination Prefix Length. Specify the destination prefix length.

Source IPv6 • Source Prefix. Specify the source destination prefix.

• Source Prefix Length. Specify the source prefix length.

Destination IPv4 L4 Port • Destination L4 port (protocol). Specify the destination IPv4 L4 port

protocol.

• Destination L4 port (value). Specify the destination IPv4 L4 port value.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual350

11. For this procedure (in which an ACL based on the destination MAC address is created),

configure the following settings:

a. In the Destination MAC field, specify the destination MAC address that must be

compared against the information in an Ethernet frame.

The valid format is xx:xx:xx:xx:xx:xx. The BPDU keyword can be specified using a

destination MAC address of 01:80:C2:xx:xx:xx.

b. In the Destination MAC Mask field, specify the destination MAC address mask that

must be compared against the information in an Ethernet frame.

The valid format is xx:xx:xx:xx:xx:xx. The BPDU keyword can be specified using a

destination MAC mask of 00:00:00:ff:ff:ff.

c. In the VLAN ID field, specify which VLAN must be compared against the information

in an Ethernet frame.

Valid range of values is 1 to 4093. Either a VLAN range or VLAN can be configured.

d. In the Binding Configuration section, from the Direction menu, select the packet

filtering direction for the ACL.

Only the inbound direction is valid.

e. In the Ports and LAG tables in the Binding Configuration section, select the ports

and LAGs to which the ACL must be applied.

f. Click the Add button.

The rule is added to the ACL and is based on the destination MAC.

12. Click the Apply button.

Your settings are saved.

Modify an ACL rule that you created with the ACL Wizard

To modify an ACL rule that you created with the ACL Wizard:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

Source IPv4 L4 Port • Source L4 port (protocol). Specify the source IPv4 L4 port protocol.

• Source L4 port (value). Specify the source IPv4 L4 port value.

Destination IPv6 L4 Port • Destination L4 port (protocol). Specify the destination IPv6 L4 port

protocol.

• Destination L4 port (value). Specify the destination IPv6 L4 port value.

Source IPv6 L4 Port • Source L4 port (protocol). Specify the source IPv6 L4 port protocol.

• Source L4 port (value). Specify the source IPv6 L4 port value.

ACL Based On Fields

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual351

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > ACL Wizard.

The ACL Wizard page displays.

6. Select check box that is associated with the rule.

7. Update the match criteria as needed.

8. Click the Apply button.

Your settings are saved.

Delete an ACL rule that you created with the ACL Wizard

To delete an ACL rule that you created with the ACL Wizard:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > ACL Wizard.

The ACL Wizard page displays.

6. Select check box that is associated with the rule.

7. Click the Delete button.

The rule is removed.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual352

ACL Wizard example

In the following figure, the ACL rule is configured to check for packet matches on ports 4, 5,

and 9 and on LAG 1. Only the Inbound option is valid. Packets that include a source address

in the 192.168.3.0/16 network are permitted to be forwarded by the interfaces. All other

packets are dropped because every ACL includes an implicit deny all rule as the last rule.

For information about the ACL Wizard, see Use the ACL Wizard to create a simple ACL on

page 347.

Configure a MAC ACL

A MAC ACL consists of a set of rules that are matched sequentially against a packet. When a

packet meets the match criteria of a rule, the specified rule action (Permit or Deny) is taken,

and the additional rules are not checked for a match. Rules for the MAC ACL are created

using the MAC ACL Rule Configuration page.

Multiple steps are involved in defining a MAC ACL and applying it to the switch:

1. Create the ACL ID.

2. Create a MAC rule.

3. Associate the MAC ACL with one or more interfaces.

You can view or delete MAC ACL configurations in the MAC Binding table (see View or

delete MAC ACL bindings in the MAC binding table on page 360.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual353

Add a MAC ACL

To add a MAC ACL:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Basic > MAC ACL.

The MAC ACL Table displays the number of ACLs currently configured in the switch and

the maximum number of ACLs that can be configured. The current size is equal to the

number of configured IPv4 and IPv6 ACLs plus the number of configured MAC ACLs.

6. In the Name field, specify a name for the MAC ACL.

The name string can include alphabetic, numeric, hyphen, underscore, or space

characters only. The name must start with an alphabetic character.

7. Click the Add button.

The MAC ACL is added.

Each configured ACL displays the following information:

• Rules. The number of rules currently configured for the MAC ACL.

• Direction. The direction of packet traffic affected by the MAC ACL, which can be

Inbound or blank.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual354

Change the name of a MAC ACL

To change the name of a MAC ACL:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Basic > MAC ACL.

The MAC ACL page displays.

6. Select check box that is associated with the rule.

7. In the Name field, specify the new name.

8. Click the Apply button.

Your settings are saved.

Delete a MAC ACL

To delete a MAC ACL:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Basic > MAC ACL.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual355

The MAC ACL page displays.

6. Select check box that is associated with the rule.

7. Click the Delete button.

The rule is removed.

Configure MAC ACL rules

You can define rules for MAC-based ACLs. The access list definition includes rules that

specify whether traffic matching the criteria is forwarded normally or discarded. A default

deny all rule is the last rule of every list.

Add a rule to a MAC ACL

To add a rule to a MAC ACL:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Basic > MAC Rules.

The following figure does not show all columns.

6. From the ACL Name menu, select the MAC ACL.

7. In the Sequence Number field, enter a whole number in the range of 1 to 2147483647 to

identify the rule.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual356

8. From the Action menu, select the action that must be taken if a packet matches the rule’s

criteria:

• Permit. Forwards packets that meet the ACL criteria.

•Deny. Drops packets that meet the ACL criteria.

9. In the Assign Queue field, specify the hardware egress queue identifier that must be used

to handle all packets matching this ACL rule.

The valid range of queue IDs is 0 to 7.

10. From the Mirror Interface menu, select the specific egress interface to which the matching

traffic stream must be copied, in addition to being forwarded normally by the switch.

This field cannot be set if a redirect interface is already configured for the ACL rule. This

field is visible for a Permit action.

11. From the Redirect Interface menu, select the egress interface to which the matching traffic

stream must be redirected, bypassing any forwarding decision normally performed by the

switch.

This field cannot be set if a mirror interface is already configured for the ACL rule.

12. From the Match Every menu, select whether each Layer 2 MAC packet must be matched

against the rule:

• True. Each packet must match the selected ACL rule.

•False. Not all packets need to match the selected ACL rule.

13. In the CoS field, specify the 802.1p user priority that must be compared against the

information in an Ethernet frame.

The valid range of values is 0 to 7.

14. In the Destination MAC field, specify the destination MAC address that must be compared

against the information in an Ethernet frame.

The valid format is xx:xx:xx:xx:xx:xx. The BPDU keyword can be specified using a

destination MAC address of 01:80:C2:xx:xx:xx.

15. In the Destination MAC Mask field, specify the destination MAC address mask that must

be compared against the information in an Ethernet frame.

The valid format is xx:xx:xx:xx:xx:xx. The BPDU keyword can be specified using a

destination MAC mask of 00:00:00:ff:ff:ff.

16. From the EtherType Key menu, select the EtherType value that must be compared against

the information in an Ethernet frame.

The valid values are as follows:

• Appletalk

• ARP

• IBM SNA

• IPv4

• IPv6

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual357

• IPX

• MPLS multicast

• MPLS unicast

• NetBIOS

• Novell

• PPPoE

• Reverse ARP

• User Value

17. In the EtherType User Value field, specify the customized EtherType value that must be

used when you select User Value from the EtherType Key menu.

This value must be compared against the information in an Ethernet frame. The valid range

of values is 0x0600 to 0xFFFF.

18. In the Source MAC field, specify the source MAC address that must be compared against

the information in an Ethernet frame.

The valid format is xx:xx:xx:xx:xx:xx.

19. In the Source MAC Mask field, specify the source MAC address mask that must be

compared against the information in an Ethernet frame.

The valid format is xx:xx:xx:xx:xx:xx.

20. In the VLAN field, specify the VLAN ID that must be compared against the information in an

Ethernet frame.

The valid range of values is 1 to 4095. Either VLAN range or VLAN can be configured.

21. From the Logging menu, select whether to enable or disable logging.

When set to Enable, logging is enabled for this ACL rule (subject to resource availability

on the switch). If the access list trap flag is also enabled, periodic traps are generated,

indicating the number of times the rule was evoked during the report interval. A fixed

five-minute report interval is used for the switch. A trap is not issued if the ACL rule hit

count is zero for the interval. This field is only supported for a deny action.

22. Click the Add button.

The rule is added.

Change the match criteria for a MAC rule

To change the match criteria for a MAC rule:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual358

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Basic > MAC Rules.

The MAC Rules page displays.

6. Select the check box that is associated with the rule.

7. Modify the fields as needed.

8. Click the Apply button.

Your settings are saved.

Delete a rule for a MAC ACL

To delete a rule for a MAC:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Basic > MAC Rules.

The MAC Rules page displays.

6. Select the check box that is associated with the rule.

7. Click the Delete button.

The rule is removed.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual359

Configure MAC bindings

When an ACL is bound to an interface, all the rules that are defined are applied to the

selected interface. You can assign MAC ACL lists to ACL priorities and interfaces.

To configure MAC bindings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Basic > MAC Binding Configuration.

6. From the ACL ID menu, select an ACL.

The fixed selection from the Direction menu is Inbound, which means that MAC ACL

rules are applied to traffic entering the interface.

7. In the Sequence Number field, optionally specify a number to indicate the order of the

access list relative to other access lists already assigned to the interface and direction.

A low number indicates high precedence order. If a sequence number is already in use

for the interface and direction, the specified access list replaces the currently attached

access list using that sequence number. If you do not specify the sequence number, a

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual360

sequence number that is one number greater than the highest sequence number

currently in use for this interface and direction is used. The valid range is 1–4294967295.

8. To add the selected ACL to a port or LAG, in the Ports table or LAG table, click the port or

LAG so that a check mark displays.

You can add the ACL to several ports and LAGs.

The Ports and LAG tables display the available and valid interfaces for ACL binding. All

nonrouting physical interfaces, VLAN interfaces, and interfaces participating in LAGs are

listed.

9. Click the Apply button.

Your settings are saved.

The following table describes the information displayed in the Interface Binding Status table.

Table 84. Interface Binding Status table

Field Description

Interface The interface of the ACL assigned.

Direction The selected packet filtering direction for the ACL.

ACL Type The type of ACL assigned to the selected interface and direction.

ACL ID The ACL number (for an IP ACL) or ACL name for a MAC ACL)

identifying the ACL assigned to the selected interface and direction.

Sequence Number The sequence number signifying the order of the specified ACL relative

to other ACLs assigned to the selected interface and direction.

View or delete MAC ACL bindings in the MAC binding

table

You can view or delete the MAC ACL bindings in the MAC binding table.

To view or delete MAC ACL bindings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual361

The default password is password.

The System Information page displays.

5. Select Security > ACL > Basic > MAC Binding Table.

6. To delete a MAC ACL-to-interface binding, do the following:

a. Select the check box next to the interface.

b. Click the Delete button.

The binding is removed.

The following table describes the information that is displayed in the MAC binding table.

Table 85. MAC Binding Table

Field Description

Interface The interface of the ACL assigned.

Direction The selected packet filtering direction for the ACL.

ACL Type The type of ACL assigned to the selected interface and direction.

ACL ID The ACL name identifying the ACL assigned to the selected interface

and direction.

Sequence Number The sequence number signifying the order of the specified ACL relative

to other ACLs assigned to the selected interface and direction.

Configure a basic or extended IPv4 ACL

An IPv4 ACL consists of a set of rules that are matched sequentially against a packet. When

a packet meets the match criteria of a rule, the specified rule action (Permit or Deny) is taken,

and the additional rules are not checked for a match. You must specify the interfaces to

which an IPv4 ACL applies, as well as whether it applies to inbound or outbound traffic.

Multiple steps are involved in defining an IPv4 ACL and applying it to the switch:

1. Add an IPv4 ACL ID (see Add an IPv4 ACL on page 362).

The differences between a basic IPv4 ACL and an extended IPv4 ACL are as follows:

• Numbered ACL from 1 to 99. Creates a basic IPv4 ACL, which allows you to permit

or deny traffic from a source IP address.

•Numbered ACL from 100 to 199. Creates an extended IPv4 ACL, which allows you

to permit or deny specific types of Layer 3 or Layer 4 traffic from a source IP address

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual362

to a destination IP address. This type of ACL provides more granularity and filtering

capabilities than the basic IP ACL.

• Named IP ACL. Create an extended IPv4 ACL with a name string that is up to 31

alphanumeric characters in length. The name must start with an alphabetic character.

2. Create an IPv4 rule (see Configure rules for a basic IPv4 ACL on page 364 or

Configure rules for an extended IPv4 ACL on page 368).

3. Associate the IPv4 ACL with one or more interfaces (see Configure IP ACL interface

bindings on page 385).

You can view or delete IPv4 ACL configurations in the IP ACL Binding table (see View or

delete IP ACL bindings in the IP ACL binding table on page 387.

Add an IPv4 ACL

To add an IPv4 ACL:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Advanced > IP ACL.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual363

The IP ACL page shows the current size of the ACL table compared to the maximum size

of the ACL table. The current size is equal to the number of configured IPv4 and IPv6

ACLs plus the number of configured MAC ACLs. The maximum size is 100.

The Current Number of ACL field displays the current number of all ACLs configured on

the switch.

The Maximum ACL field displays the maximum number of IP ACLs that can be

configured on the switch.

6. In the IP ACL ID field, specify the ACL ID or IP ACL name, which depends on the IP ACL

type. The IP ACL ID is an integer in the following range:

• 1–99. Creates a basic IP ACL, which allows you to permit or deny traffic from a

source IP address.

• 100–199. Creates an extended IP ACL, which allows you to permit or deny specific

types of Layer 3 or Layer 4 traffic from a source IP address to a destination IP

address. This type of ACL provides more granularity and filtering capabilities than the

standard IP ACL.

• IP ACL Name. Create an IPv4 ACL name string that is up to 31 alphanumeric

characters in length. The name must start with an alphabetic character.

Each configured ACL displays the following information:

• Rules. The number of rules currently configured for the IP ACL.

•Type. Identifies the ACL as a basic IP ACL (with ID from 1 to 99), extended IP ACL

(with ID from 100 to 199), or a named IP ACL.

7. Click the Add button.

The IP ACL is added to the switch configuration.

Change the number or name of an IPv4 ACL

To change the number or name of an IPv4 ACL:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Advanced > IP ACL.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual364

The IP ACL Configuration page displays.

6. Select the check box that is associated with the IP ACL.

7. In the IP ACL field, specify the new number or name.

8. Click the Apply button.

Your settings are saved.

Delete an IPv4 ACL

To delete an IPv4 ACL:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Advanced > IP ACL.

The IP ACL Configuration page displays.

6. Select the check box that is associated with the IP ACL.

7. Click the Delete button.

The IP ACL is removed.

Configure rules for a basic IPv4 ACL

You can define rules for IP-based standard ACLs (basic ACLs). The access list definition

includes rules that specify whether traffic matching the criteria is forwarded normally or

discarded.

Note: An implicit deny all rule is included at the end of an ACL list. This

means that if an ACL is applied to a packet, and if none of the explicit

rules match, then the final implicit deny all rule applies and the packet

is dropped.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual365

Add a rule for a basic IPv4 ACL

To add a rule for a basic IPv4 ACL:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Advanced > IP Rules.

If no rules exist, the Basic ACL Rule Table shows the message No rules have been

configured for this ACL. If one or more rules exist for the ACL, the rules display in the

Basic ACL Rule Table.

6. From the ACL ID menu, select the IP ACL for which you want to add a rule.

For basic IP ACLs, this must be an ID in the range from 1 to 99.

7. Click the Add button.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual366

8. Specify the following match criteria for the rule:

• Sequence Number . Enter an ACL sequence number in the range of 1 to 2147483647

that is used to identify the rule. An IP ACL can contain up to 50 rules.

• Action. Select the ACL forwarding action, which is one of the following:

- Permit. Forward packets that meet the ACL criteria.

- Deny. Drop packets that meet the ACL criteria.

• Egress Queue. If the selection form the Action menu is Permit, you can specify the

hardware egress queue identifier that is used to handle all packets matching this IP

ACL rule. The range of queue IDs is 0 to 7.

• Logging. If the selection form the Action menu is Deny, you can enable logging for

the ACL by selecting the Enable radio button. (Logging is subject to resource

availability in the device.)

If the access list trap flag is also enabled, periodic traps are generated, indicating the

number of times this rule was evoked during the report interval. A fixed five-minute

report interval is used for the switch. A trap is not issued if the ACL rule hit count is

zero for the current interval.

• Match Every. From the Match Every menu, select whether all packets must match

the selected IP ACL rule:

- Enable. All packets must match the selected IP ACL rule and are either permitted

or denied.

-Disable. Not all packets need to match the selected IP ACL rule.

• Mirror Interface. From the Mirror Interface menu, select the specific egress

interface to which the matching traffic stream must be copied, in addition to being

forwarded normally by the switch.

This field cannot be set if a redirect interface is already configured for the IP ACL rule.

This field is visible for a Permit action.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual367

• Redirect Interface. From the Redirect Interface menu, select the egress interface to

which the matching traffic stream must be redirected, bypassing any forwarding

decision normally performed by the switch.

This field cannot be set if a mirror interface is already configured for the IP ACL rule.

• Src IP Address. Enter an IP address using dotted-decimal notation to be compared

to a packet’s source IP address as a match criterion for the selected IP ACL rule.

• Src IP Mask. Specify the IP mask in dotted-decimal notation to be used with the

source IP address value.

9. Click the Apply button.

Your settings are saved.

Modify the match criteria for a basic IPv4 ACL rule

To modify the match criteria for a basic IPv4 ACL rule:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Advanced > IP Rules.

The IP Rules page displays.

6. From the ACL ID menu, select the ACL that includes the rule that you want to modify.

7. In the Basic ACL Rule Table, click the rule.

The rule is a hyperlink. The Standard ACL Rule Configuration page displays.

8. Modify the basic IP ACL rule criteria.

9. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual368

Delete a basic IPv4 ACL rule

To delete a basic IPv4 ACL rule:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Advanced > IP Rules.

The IP Rules page displays.

6. From the ACL ID menu, select the ACL that includes the rule that you want to modify.

7. In the Basic ACL Rule Table, select the check box that is associated with the rule.

8. Click the Delete button.

The rule is removed.

Configure rules for an extended IPv4 ACL

You can define rules for extended IP-based ACLs. The access list definition includes rules

that specify whether traffic matching the criteria is forwarded normally or discarded.

Note: An implicit deny all rule is included at the end of an ACL list. This

means that if an ACL is applied to a packet and if none of the explicit

rules match, then the final implicit deny all rule applies and the packet

is dropped.

Add a rule for an extended IPv4 ACL

To add a rule for an extended IPv4 ACL:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual369

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Advanced > IP Extended Rules.

The previous figure does not show all columns on the page.

If no rules exists, the Extended ACL Rule Table shows the message No rules have been

configured for this ACL. If one or more rules exist for the ACL, the rules display in the

Extended ACL Rule Table.

6. From the ACL ID/Name menu, select the IP ACL for which you want to add a rule.

For extended IP ACLs, this must be an ID in the range from 101 to 199 or a name.

7. Click the Add button.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual370

8. Configure the following match criteria for the rule:

• Sequence Number. Enter a whole number in the range of 1 to 2147483647 that is

used to identify the rule. An extended IP ACL can contain up to 50 rules.

• Action. Select the ACL forwarding action, which is one of the following:

-Permit. Forward packets that meet the ACL criteria.

-Deny. Drop packets that meet the ACL criteria.

•Egress Queue. If the selection from the Action menu is Permit, select the hardware

egress queue identifier that is used to handle all packets matching this IP ACL rule.

The range of queue IDs is 0 to 7.

•Logging. If the selection form the Action menu is Deny, you can enable logging for

the ACL by selecting the Enable radio button. (Logging is subject to resource

availability in the device.)

If the access list trap flag is also enabled, periodic traps are generated, indicating the

number of times this rule was evoked during the report interval. A fixed five-minute

report interval is used for the switch. A trap is not issued if the ACL rule hit count is

zero for the current interval.

• Match Every. From the Match Every menu, select whether all packets must match

the selected IP ACL rule:

-False. Not all packets need to match the selected IP ACL rule. You can configure

other match criteria on the page.

- True. All packets must match the selected IP ACL rule and are either permitted or

denied. In this case, you cannot configure other match criteria on the page.

•Interface. For a Permit action, use either a mirror interface or a redirect interface:

-Select the Mirror Interface radio button and use the menu to specify the egress

interface to which the matching traffic stream is copied, in addition to being

forwarded normally by the device.

-Select the Redirect Interface radio button and use the menu to specify the

egress interface to which the matching traffic stream is forced, bypassing any

forwarding decision normally performed by the device.

•Protocol Type. From the menu, select a protocol that a packet’s IP protocol must be

matched against: IP, ICMP, IGMP, TCP, UDP, EIGRP, GRE, IPINIP, OSPF, PIM, or

Other. If you select Other, specify enter a protocol number from 0 to 255.

• Src. In the Src field, enter a source IP address, using dotted-decimal notation, to be

compared to a packet’s source IP address as a match criterion for the selected IP

ACL rule:

-If you select the IP Address radio button, enter an IP address or an IP address

range. You can enter a relevant wildcard mask to apply this criteria. If this field is

left empty, it means any.

-If you select the Host radio button, the wildcard mask is configured as 0.0.0.0. If

this field is left empty, it means any.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual371

The wildcard mask determines which bits are used and which bits are ignored. A

wildcard mask of 0.0.0.0 indicates that none of the bits are important. A wildcard of

255.255.255.255 indicates that all of the bits are important.

• Src L4. The options are available only when the protocol is set to TCP or UDP. Use the

source L4 port option to specify relevant matching conditions for L4 port numbers in

the extended ACL rule.

You can select either the Port radio button or the Range radio button:

-If you select the Port radio button, you can either enter the port number yourself

or select one of the following protocols from the menu:

•The source IP TCP port protocols are domain, echo, ftp, ftpdata, www-http,

smtp, telnet, pop2, pop3, and bgp.

•The source IP UDP port protocols are domain, echo, snmp, ntp, rip, time,

who, and tftp.

Each of these values translates into its equivalent port number, which is used as

both the start and end of the port range.

Select Other from the menu to enter a port number. If you select Other from the

menu but leave the field blank, it means any.

The relevant matching conditions for L4 port numbers are as follows:

• Equal. IP ACL rule matches only if the Layer 4 source port number is equal to

the specified port number or port protocol.

•Less Than. IP ACL rule matches if the Layer 4 source port number is less

than the specified port number.

• Greater Than. IP ACL rule matches if the Layer 4 source port number is

greater than the specified port number.

• Not Equal. IP ACL rule matches only if the Layer 4 source port number is not

equal to the specified port number or port protocol.

-If you select the Range radio button, the IP ACL rule matches only if the Layer 4

source port number is within the specified port range. The starting port, ending

port, and all ports in between are a part of the Layer 4 port range.

The Start Port and End Port fields identify the first and last ports that are part of

the port range. The values can range from 0 to 65535.

You can either enter the port range yourself or select one of the following

protocols from the menu:

•The destination IP TCP port protocols are domain, echo, ftp, ftpdata,

www-http, smtp, telnet, pop2, pop3, and bgp.

•The destination IP UDP port protocols are domain, echo, snmp, ntp, rip,

time, who, and tftp.

Each of these values translates into its equivalent port number, which is used as

both the start and end of the port range.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual372

Select Other from the menu to enter a port number. If you select Other from the

menu but leave the field blank, it means any.

The wildcard mask determines which bits are used and which bits are ignored. A

wildcard mask of 0.0.0.0 indicates that none of the bits are important. A wildcard

of 255.255.255.255 indicates that all of the bits are important.

• Dst. In the Dst field, enter a destination IP address, using dotted-decimal notation, to

be compared to a packet’s destination IP address as a match criterion for the selected

IP ACL rule:

-If you select the IP Address radio button, enter an IP address with a relevant

wildcard mask to apply this criteria. If this field is left empty, it means any.

-If you select the Host radio button, the wildcard mask is configured as 0.0.0.0. If

this field is left empty, it means any.

The wildcard mask determines which bits are used and which bits are ignored. A

wildcard mask of 0.0.0.0 indicates that none of the bits are important. A wildcard of

255.255.255.255 indicates that all of the bits are important.

• Dst L4. The options are available only when the protocol is set to TCP or UDP. Use the

destination L4 port option to specify relevant matching conditions for L4 port numbers

in the extended ACL rule.

You can select either the Port radio button or the Range radio button:

-If you select the Port radio button, you can either enter the port number yourself

or select one of the following protocols from the menu.

•The destination IP TCP port protocols are domain, echo, ftp, ftpdata,

www-http, smtp, telnet, pop2, pop3, and bgp.

•The destination IP UDP port protocols are domain, echo, snmp, ntp, rip,

time, who, and tftp.

Each of these values translates into its equivalent port number, which is used as

both the start and end of the port range.

Select Other from the menu to enter a port number. If you select Other from the

menu but leave the field blank, it means any.

The relevant matching conditions for L4 port numbers are as follows:

• Equal. The IP ACL rule matches only if the Layer 4 destination port number is

equal to the specified port number or port protocol.

•Less Than. The IP ACL rule matches if the Layer 4 destination port number is

less than the specified port number.

• Greater Than. The IP ACL rule matches if the Layer 4 destination port

number is greater than the specified port number.

• Not Equal. The IP ACL rule matches only if the Layer 4 destination port

number is not equal to the specified port number or port protocol.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual373

-If you select the Range radio button, the IP ACL rule matches only if the Layer 4

destination port number is within the specified port range. The starting port,

ending port, and all ports in between are a part of the Layer 4 port range.

The Start Port and End Port fields identify the first and last ports that are part of

the port range. They values can range from 0 to 65535.

You can either select the enter the port range yourself or select one of the

following protocols from the menu:

•The destination IP TCP port range names are domain, echo, ftp, ftpdata,

www-http, smtp, telnet, pop2, pop3, and bgp.

•The destination IP UDP port range names are domain, echo, snmp, ntp, rip,

time, who, and tftp.

Each of these values translates into its equivalent port number, which is used as

both the start and end of the port range.

Select Other from the menu to enter a port number. If you select Other from the

menu but leave the field blank, it means any.

The wildcard mask determines which bits are used and which bits are ignored. A

wildcard mask of 0.0.0.0 indicates that none of the bits are important. A wildcard

of 255.255.255.255 indicates that all of the bits are important.

• IGMP Type. If you specify the IGMP type, the IP ACL rule matches the specified

IGMP message type. Possible values are in the range 0 to 255. If this field is left

empty, it means any.

• ICMP. Select either the Type or Message radio button:

-If you select the Type radio button, note the following:

•The Type and Code fields are enabled only if the protocol is ICMP. Use these

fields to specify a match condition for ICMP packets:

•The IP ACL rule matches the specified ICMP message type. Possible type

numbers are in the range from 0 to 255.

•If you specify information in the Message field, the IP ACL rule matches the

specified ICMP message code. Possible values for the code can be in the

range from 0 to 255.

•If these fields are left empty, it means any.

-If you select the Message radio button, select the type of the ICMP message to

match with the selected IP ACL rule. Specifying a type of message implies that

both the ICMP type and ICMP code are specified. The ICMP message is decoded

into the corresponding ICMP type and ICMP code within the ICMP type.

The IPv4 ICMP message types are echo, echo-reply, host-redirect,

mobile-redirect, net-redirect, net-unreachable, redirect, packet-too-big,

port-unreachable, source-quench, router-solicitation, router-advertisement,

ttl-exceeded, time-exceeded, and unreachable.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual374

• Fragments. Either select the Enable radio button to allow initial fragments (that is,

the fragment bit is asserted) or leave the default Disable radio button selected to

prevent initial fragments from being used.

This option is not valid for rules that match L4 information such as a TCP port number,

because that information is carried in the initial packet.

• Service Type. Select a service type match condition for the extended IP ACL rule.

The possible options are IP DSCP, IP precedence, and IP TOS , which are alternative

methods to specify a match criterion for the same service type field in the IP header.

Each method uses a different user notation. After you make a selection, you can

specify the appropriate values:

- IP DSCP. This is an optional configuration. Specify the IP DiffServ Code Point

(DSCP) field. The DSCP is defined as the high-order 6 bits of the service type

octet in the IP header. Enter an integer from 0 to 63. To select the IP DSCP, select

one of the DSCP keywords from the menu. To specify a numeric value, select

Other and a field displays in which you can enter numeric value of the DSCP.

- IP Precedence. This is an optional configuration. The IP precedence field in a

packet is defined as the high-order 3 bits of the service type octet in the IP header .

Enter an integer from 0 to 7.

- IP TOS. This is an optional configuration. The IP ToS field in a packet is defined

as all 8 bits of the service type octet in the IP header. The ToS bits value is a

hexadecimal number that is composed of numbers 00 to 09 and AA to FF. The

ToS mask value is a hexadecimal number that is composed of numbers 00 to FF.

The ToS mask denotes the bit positions in the ToS bits value that are used for

comparison against the IP ToS field in a packet.

For example, to check for an IP ToS value for which bit 7 is set and is the most

significant value, for which bit 5 is set, and for which bit 1 is cleared, use a ToS

bits value of 0xA0 and a ToS mask of 0xFF.

9. Click the Apply button.

Your settings are saved.

Modify the match criteria for an extended IPv4 ACL rule

To modify the match criteria for an existing extended IPv4 ACL rule:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual375

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Advanced > IP Extended Rules.

The IP Rules page displays.

6. From the ACL ID menu, select the ACL that includes the rule that you want to modify.

7. In the Extended ACL Rule Table, click the rule.

The rule is a hyperlink. The Extended ACL Rule Configuration page displays.

8. Modify the extended IP ACL rule criteria.

9. Click the Apply button.

Your settings are saved.

Delete an extended IPv4 ACL rule

To delete an extended IPv4 ACL rule:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Advanced > IP Extended Rules.

The IP Rules page displays.

6. From the ACL ID menu, select the ACL that includes the rule that you want to delete.

7. In the Extended ACL Rule Table, select the check box that is associated with the rule.

8. Click the Delete button.

The rule is removed.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual376

Configure an IPv6 ACL

An IPv6 ACL consists of a set of rules that are matched sequentially against a packet. When

a packet meets the match criteria of a rule, the specified rule action (Permit or Deny) is taken,

and the additional rules are not checked for a match. You must specify the interfaces to

which an IPv6 ACL applies, as well as whether it applies to inbound or outbound traffic.

Multiple steps are involved in defining an IPv6 ACL and applying it to the switch:

1. Add an IPv6 ACL ID (see Configure an IPv6 ACL on page 376).

An IPv6 ACL must start with a name string that is up to 31 alphanumeric characters in

length. The name must start with an alphabetic character.

2. Create an IPv6 rule (see Configure rules for an IPv6 ACL on page 379).

3. Associate the IPv6 ACL with one or more interfaces (see Configure IP ACL interface

bindings on page 385).

You can view or delete IPv6 ACL configurations in the IP ACL Binding table (see View or

delete IP ACL bindings in the IP ACL binding table on page 387.

Add an IPv6 ACL

To add an IPv6 ACL:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Advanced > IPv6 ACL.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual377

6. In the IPv6 ACL field, specify a name to identify the IPv6 ACL.

This is the IPv6 ACL name string, which includes up to 31 alphanumeric characters only.

The name must start with an alphabetic character.

7. Click the Add button.

The IPv6 ACL is added.

The following table describes the nonconfigurable information displayed on the page.

Table 86. IPv6 Configuration and IPv6 ACL Table information

Field Description

Current Number of ACL The current number of the IP ACLs configured on the switch.

Maximum ACL The maximum number of IP ACLs that can be configured on the switch.

Rules The number of the rules associated with the IP ACL.

Type The type is IPv6 ACL.

Change the name of an IPv6 ACL

To change the name of an IPv6 ACL:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual378

The default password is password.

The System Information page displays.

5. Select Security > ACL > Advanced > IPv6 ACL.

The IPv6 ACL Configuration page displays.

6. Select the check box that is associated with the IPv6 ACL.

7. In the IPv6 ACL field, specify the new name.

8. Click the Apply button.

Your settings are saved.

Delete an IPv6 ACL

To delete an IPv6 ACL:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Advanced > IPv6 ACL.

The IPv6 Configuration page displays.

6. Select the check box that is associated with the IPv6 ACL.

7. Click the Delete button.

The IPv6 ACL is removed.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual379

Configure rules for an IPv6 ACL

You can define rules for IPv6 ACLs. The access list definition includes rules that specify

whether traffic matching the criteria is forwarded normally or discarded.

Add a rule for an IPv6 ACL

Add a rule for an ACL IPv6:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Advanced > IPv6 Rules.

The previous figure does not show all columns on the page.

If no rules exists, the IPv6 ACL Rule Table shows the message No rules have been

configured for this ACL. If one or more rules exist for the ACL, the rules display in the

IPv6 ACL Rule Table.

6. From the ACL Name menu, select the IPv6 ACL for which you want to add a rule.

An IPv6 ACL can contain up to 50 rules.

7. Click the Add button.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual380

8. Configure the following match criteria for the rule:

• Action. Select the ACL forwarding action by selecting one of the following radio

buttons:

- Permit. Forward packets that meet the ACL criteria.

- Deny. Drop packets that meet the ACL criteria.

• Egress Queue. If you select the Permit radio button, select the hardware egress

queue identifier that is used to handle all packets matching this IPv6 ACL rule. The

range of queue IDs is 0 to 7.

•Logging. If you select the Deny radio button, you can enable logging for the ACL by

selecting the Enable radio button. (Logging is subject to resource availability in the

device.)

If the access list trap flag is also enabled, periodic traps are generated, indicating the

number of times this rule was evoked during the report interval. A fixed five-minute

report interval is used for the switch. A trap is not issued if the ACL rule hit count is

zero for the current interval.

• Match Every. Select whether all packet must match the selected IPv6 ACL rule:

- Disable. Not all packets need to match the selected IPv6 ACL rule. You can

configure other match criteria on the page.

- Enable. All packets must match the selected IPv6 ACL rule and are either

permitted or denied. In this case, you cannot configure other match criteria on the

page.

•Protocol Type. Specify the IPv6 protocol type in one of the following ways:

-From the Protocol Type menu, select IPv6, ICMPv6, TCP, or UDP.

-From the Protocol Type menu, select Other, and in the associated field, specify

an integer ranging from 0 to 255. This number represents the IPv6 protocol.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual381

• Src. In the Src field, enter a source IPv6 address or source IPv6 address range to be

compared to a packet’s source IPv6 address as a match criterion for the selected

IPv6 ACL rule:

-If you select the IPv6 Address radio button, enter an IPv6 address or IPv6 range

to apply this criteria. If this field is left empty, it means any.

-If you select the Host radio button, enter a host source IPv6 address to match the

specified IPv6 address. If this field is left empty, it means any.

The source IPv6 address argument must be in the form documented in RFC 2373

where the address is specified in hexadecimal numbers using 16-bit values between

colons.

• Src L4. The options are available only when the protocol is set to TCP or UDP. Use the

source L4 port option to specify relevant matching conditions for L4 port numbers in

the extended ACL rule.

You can select either the Port radio button or the Range radio button:

-If you select the Port radio button, you can either enter the port number yourself

or select one of the following protocols from the menu:

•The source IP TCP port protocols are domain, echo, ftp, ftpdata, www-http,

smtp, telnet, pop2, pop3, and bgp.

•The source IP UDP port protocols are domain, echo, snmp, ntp, rip, time,

who, and tftp.

Each of these values translates into its equivalent port number, which is used as

both the start and end of the port range.

Select Other from the menu to enter a port number. If you select Other from the

menu but leave the field blank, it means any.

The relevant matching conditions for L4 port numbers are as follows:

• Equal. The IPv6 ACL rule matches only if the Layer 4 source port number is

equal to the specified port number or port protocol.

•Less Than. The IPv6 ACL rule matches if the Layer 4 source port number is

less than the specified port number.

• Greater Than. The IPv6 ACL rule matches if the Layer 4 source port number

is greater than the specified port number.

• Not Equal. The IPv6 ACL rule matches only if the Layer 4 source port number

is not equal to the specified port number or port protocol.

-If you select the Range radio button, the IPv6 ACL rule matches only if the

Layer 4 source port number is within the specified port range. The starting port,

ending port, and all ports in between are a part of the Layer 4 port range.

The Start Port and End Port fields identify the first and last ports that are part of

the port range. They values can range from 0 to 65535.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual382

You can either enter the port range yourself or select one of the following

protocols from the menu:

•The source IP TCP port protocols are domain, echo, ftp, ftpdata, www-http,

smtp, telnet, pop2, pop3, and bgp.

•The source IP UDP port protocols are domain, echo, snmp, ntp, rip, time,

who, and tftp.

Each of these values translates into its equivalent port number, which is used as

both the start and end of the port range.

Select Other from the menu to enter port numbers. If you select Other from the

menu but leave the fields blank, it means any.

• Dst. In the Dst field, enter a destination IPv6 address to be compared to a packet’s

destination IPv6 address as a match criterion for the selected IPv6 ACL rule:

-If you select the IPv6 Address radio button, enter an IPv6 address to apply this

criteria. If this field is left empty, it means any.

-If you select the Host radio button, enter a host source IPv6 address to match the

specified IPv6 address. If this field is left empty, it means any.

The source IPv6 address argument must be in the form documented in RFC 2373

where the address is specified in hexadecimal numbers using 16-bit values between

colons.

• Dst L4. The options are available only when the protocol is set to TCP or UDP. Use the

destination L4 port option to specify relevant matching conditions for L4 port numbers

in the extended ACL rule.

You can select either the Port radio button or the Range radio button:

-If you select the Port radio button, you can either enter the port number yourself

or select one of the following protocols from the menu:

•The destination IP TCP port protocols are domain, echo, ftp, ftpdata,

www-http, smtp, telnet, pop2, pop3, and bgp.

•The destination IP UDP port protocols are domain, echo, snmp, ntp, rip,

time, who, and tftp.

Each of these values translates into its equivalent port number, which is used as

both the start and end of the port range.

Select Other from the menu to enter a port number. If you select Other from the

menu but leave the field blank, it means any.

The relevant matching conditions for L4 port numbers are as follows:

• Equal. The IPv6 ACL rule matches only if the Layer 4 destination port number

is equal to the specified port number or port protocol.

•Less Than. The IPv6 ACL rule matches if the Layer 4 destination port number

is less than the specified port number.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual383

• Greater Than. The IPv6 ACL rule matches if the Layer 4 destination port

number is greater than the specified port number.

• Not Equal. The IPv6 ACL rule matches only if the Layer 4 destination port

number is not equal to the specified port number or port protocol.

-If you select the Range radio button, the IPv6 ACL rule matches only if the

Layer 4 destination port number is within the specified port range. The starting

port, ending port, and all ports in between are a part of the Layer 4 port range.

The Start Port and End Port fields identify the first and last ports that are part of

the port range. They values can range from 0 to 65535.

You can either enter the port range yourself or select one of the following

protocols from the menu:

•The destination IP TCP port protocols are domain, echo, ftp, ftpdata,

www-http, smtp, telnet, pop2, pop3, and bgp.

•The destination IP UDP port protocols are domain, echo, snmp, ntp, rip,

time, who, and tftp.

Each of these values translates into its equivalent port number, which is used as

both the start and end of the port range.

Select Other from the menu to enter port numbers. If you select Other from the

menu but leave the fields blank, it means any.

• ICMPv6. Select either the Type or Message radio button:

-If you select the Type radio button, note the following:

•The Type and Message fields are enabled only if the protocol is ICMPv6. Use

these fields to specify a match condition for ICMPv6 packets.

•The IPv6 ACL rule matches the specified ICMPv6 message type. Possible

type numbers are in the range from 0 to 255.

•If you specify information in the Message field, the IPv6 ACL rule matches the

specified ICMPv6 message code. Possible values for code can be in the

range from 0 to 255.

•If these fields are left empty, it means any.

-If you select the Message radio button, select the type of the ICMPv6 message to

match with the selected IPv6 ACL rule. Specifying a type of message implies that

both the ICMPv6 type and ICMPv6 code are specified. The ICMPv6 message is

decoded into the corresponding ICMPv6 type and ICMPv6 code within the ICMP

type.

The ICMPv6 message types are destination-unreachable, echo-reply,

echo-request, header, hop-limit, mld-query, mld-reduction, mld-report,

nd-na, nd-ns, next-header, no-admin, no-route, packet-too-big,

port-unreachable, router-solicitation, router-advertisement,

router-renumbering, time-exceeded, and unreachable.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual384

• Fragments. Either select the Enable radio button to allow initial fragments (that is,

the fragment bit is asserted) or leave the default Disable radio button selected to

prevent initial fragments from being used.

This option is not valid for rules that match L4 information such as TCP port number,

because that information is carried in the initial packet.

• Routing. Either select the Enable radio button to match packets that include a routing

extension header or leave the default Disable radio button selected to ignore the

routing extension headers in packets.

• Flow Label. The Flow Label field is enabled only if selection from the Protocol Type

menu is ICMPv6. The flow label is 20-bit number that is unique to an IPv6 packet and

that is used by end stations to signify Quality of Service handling in routers. The flow

label can specified within the range 0 to 1048575.

• IPv6 DSCP Service. Specify the IP DiffServ Code Point (DSCP) field. This is an

optional configuration.

The DSCP is defined as the high-order 6 bits of the service type octet in the IPv6

header. Enter an integer from 0 to 63. To select the IPv6 DSCP, select one of the

DSCP keywords. To specify a numeric value, select Other and enter the numeric

value of the DSCP.

9. Click the Apply button.

Your settings are saved.

Modify the match criteria for an IPv6 ACL rule

To modify the match criteria for an IPv6 ACL rule:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Advanced > IPv6 Rules.

The IPv6 Rules page displays.

6. From the ACL Name menu, select the ACL that includes the rule that you want to modify.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual385

7. In the IPv6 ACL Rule Table, click the rule.

The rule is a hyperlink. The IPv6 ACL Rule Configuration page displays.

8. Modify the IPv6 ACL rule criteria.

9. Click the Apply button.

Your settings are saved.

Delete an IPv6 ACL rule

To delete an IPv6 ACL rule:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Advanced > IPv6 Rules.

The IPv6 Rules page displays.

6. From the ACL Name menu, select the ACL that includes the rule that you want to delete.

7. In the IPv6 ACL Rule Table, select the check box that is associated with the rule.

8. Click the Delete button.

The rule is removed.

Configure IP ACL interface bindings

When you bind a basic IPv4, extended IPv4, or IPv6 ACL to an interface, all the rules that

you defined for the IP ACL are applied to the selected interface.

If resources on the switch are insufficient, an attempt to bind an ACL to an interface fails.

To bind an IP ACL to one or more interfaces:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual386

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Advanced > IP Binding Configuration.

6. From the ACL ID menu, select an existing IP ACL for you which you want to add an IP ACL

interface binding.

The fixed selection from the Direction menu is Inbound, which means that MAC ACL

rules are applied to traffic entering the interface.

7. In the Sequence Number field, optionally specify a number to indicate the order of the

access list relative to other access lists already assigned to this interface and direction.

A low number indicates high precedence order. If a sequence number is already in use

for this interface and direction, the specified access list replaces the currently attached

access list using that sequence number. If you do not specify the sequence number

(meaning that the value is 0), a sequence number that is one number greater than the

highest sequence number currently in use for this interface and direction is used. The

valid range is 1–4294967295.

8. To add the selected ACL to a port or LAG, in the Ports table or LAG table, click the port or

LAG so that a check mark displays.

You can add the ACL to several ports and LAGs.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual387

The Ports and LAG tables display the available and valid interfaces for ACL binding. All

nonrouting physical interfaces, VLAN interfaces, and interfaces participating in LAGs are

listed.

9. Click the Apply button.

Your settings are saved.

The following table describes the nonconfigurable information displayed on the page.

Table 87. IP Binding Status table

Field Description

Interface The selected interface.

Direction The selected packet filtering direction for the ACL.

ACL Type The type of ACL assigned to the selected interface and direction.

ACL ID/Name The ACL number (for an IP ACL) or ACL name (for a named IP ACL or

IPv6 ACL) identifying the ACL assigned to the selected interface and

direction.

Sequence Number The sequence number signifying the order of specified ACL relative to

other ACLs assigned to the selected interface and direction.

View or delete IP ACL bindings in the IP ACL binding table

You can view or delete bindings for basic IPv4, extended IPv4, and IPv6 ACLs.

To view or delete IP ACL bindings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL > Advanced > Binding Table.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual388

6. To delete an IP ACL-to-interface binding, do the following:

a. Select the check box next to the interface.

b. Click the Delete button.

The binding is removed.

The following table describes the information displayed in the IP ACL Binding Table.

Table 88. IP ACL Binding Table

Field Description

Interface The interface.

Direction The selected packet filtering direction for the ACL.

ACL Type The type of ACL assigned to the selected interface and direction.

ACL ID/Name The ACL number (for an IP ACL) or ACL name (for a named IP ACL or

IPv6 ACL) identifying the ACL assigned to the selected interface and

direction.

Sequence Number The sequence number signifying the order of the specified ACL relative

to other ACLs assigned to the selected interface and direction.

Configure VLAN ACL bindings

You can associate a MAC ACL, any type of IPv4 ACL, or an IPv6 ACL with a VLAN. When

you do so, the ACL is applied to all interfaces that are members of the VLAN.

Add a VLAN ACL binding

To add a VLAN ACL binding:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual389

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Security > ACL> Advanced > VLAN Binding Configuration.

6. In the VLAN ID field, enter the VLAN ID to which the binding must apply.

7. From the Direction menu, select the packet filtering direction.

8. In the Sequence Number field, enter an optional sequence number.

You can specify an optional sequence number to indicate the order of this access list

relative to other access lists that are already assigned to the VLAN ID and selected

direction. A lower number indicates a higher precedence order. If a sequence number is

already in use for the VLAN ID and selected direction, the specified access list replaces

the currently attached ACL using that sequence number. If you do not specify a sequence

number (the value is 0), a sequence number that is one greater than the highest

sequence number currently in use for the VLAN ID and selected direction is used. The

valid range is 1 to 4294967295.

9. From the ACL Type menu, select the type of ACL.

Valid ACL types include IP ACL, MAC ACL, and IPv6 ACL.

10. From the ACL ID list, select the ID or name of the ACL that must be bound to the specified

VLAN.

11. Click the Add button.

The VLAN ACL binding is added.

Remove a VLAN ACL binding

To remove a VLAN ACL binding:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Manage Device Security User Manual390

The default password is password.

The System Information page displays.

5. Select Security > ACL> Advanced > VLAN Binding Configuration.

The VLAN Binding Configuration page displays.

6. Select the check box for the VLAN binding that you want to remove.

7. Click the Delete button.

The VLAN ACL binding is removed.

391

7Monitor the Switch and the Traffic

This chapter covers the following topics:

•Monitor the switch and the ports

•Configure and view the logs

•Configure port mirroring

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual392

Monitor the switch and the ports

You can view and clear port and switch statistics and perform a cable test.

View or clear switch statistics

You can view detailed statistical information about the traffic that the switch processes.

To view or clear the switch statistics

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. To view the switch statistics, select Monitoring > Ports > Switch Statistics.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual393

6. Click the Update button to refresh the page with the latest information about the switch.

7. Click the Clear button to clear all the statistics counters, resetting all switch summary and

detailed statistics to default values.

The discarded packets count cannot be cleared.

The following table describes the switch statistics displayed on the page.

Table 89. Switch statistics

Field Description

ifIndex The interface index of the interface table entry associated with the processor of

this switch.

Octets Received The total number of octets of data received by the processor (excluding framing

bits, but including FCS octets).

Packets Received Without

Errors The total number of packets (including broadcast packets and multicast

packets) received by the processor.

Unicast Packets Received The number of subnetwork-unicast packets delivered to a higher-layer protocol.

Multicast Packets Received The total number of packets received that were directed to a multicast address.

This number does not include packets directed to the broadcast address.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual394

Broadcast Packets Received The total number of packets received that were directed to the broadcast

address. This does not include multicast packets.

Receive Packets Discarded The number of inbound packets that were chosen to be discarded, even though

no errors were detected, in order to prevent their being delivered to a

higher-layer protocol. A possible reason for discarding a packet could be to free

up buffer space.

Octets T ransmitted The total number of octets transmitted out of the interface, including framing

characters.

Packets T ransmitted Without

Errors The total number of packets transmitted out of the interface.

Unicast Packets Transmitted The total number of packets that higher-level protocols requested be

transmitted to a subnetwork-unicast address, including those that were

discarded or not sent.

Multicast Packets

Transmitted The total number of packets that higher-level protocols requested be

transmitted to a multicast address, including those that were discarded or not

sent.

Broadcast Packets

Transmitted The total number of packets that higher-level protocols requested be

transmitted to the broadcast address, including those that were discarded or not

sent.

Transmit Packets Discarded The number of outbound packets that were chosen to be discarded, even

though no errors were detected, in order to prevent their being delivered to a

higher-layer protocol. A possible reason for discarding a packet could be to free

up buffer space.

Most Address Entries Ever

Used The highest number of Forwarding Database Address Table entries that were

learned by this switch since the most recent reboot.

Address Entries in Use The number of learned and static entries in the Forwarding Database Address

Table for this switch.

Maximum VLAN Entries The maximum number of VLANs allowed on this switch.

Most VLAN Entries Ever

Used The largest number of VLANs that were active on this switch since the last

reboot.

Static VLAN Entries The number of active VLAN entries on this switch that were created statically.

VLAN Deletes The number of VLANs on this switch that were created and then deleted since

the last reboot.

Time Since Counters Last

Cleared The elapsed time, in days, hours, minutes, and seconds, since the statistics for

this switch were last cleared.

Table 89. Switch statistics (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual395

View port statistics

You can view a summary of per-port traffic statistics on the switch.

To view port statistics:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Monitoring > Ports > Port Statistics.

6. Select whether to display physical interfaces, link aggregation groups (LAGs), or both by

clicking one of the following links above the table heading:

•1 (or the unit ID of the switch). Only physical interfaces are displayed. This is the

default setting.

• LAGS. Only link aggregation groups are displayed.

• All. Both physical interfaces and link aggregation groups are displayed.

To locate an interface quickly, type the interface number using the respective naming

convention (for example, g1 or l1) in the Go To Interface field above or below the table and

click the Go button. See Interface naming conventions on page 27 for more information.

The entry corresponding to the specified interface is selected.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual396

The following table describes the per-port statistics displayed on the page.

Table 90. Port statistics

Field Description

Interface This object indicates the interface of the interface table entry that is

associated with this port on an adapter.

Total Packets Received

Without Errors The total number of packets received that were without errors.

Packets Received With Error The number of inbound packets that contained errors preventing them from

being deliverable to a higher-layer protocol.

Broadcast Packets Received The total number of good packets received that were directed to the

broadcast address. This does not include multicast packets.

Packets T ransmitted Without

Errors The number of frames that were transmitted by this port to its segment.

Transmit Packet Errors The number of outbound packets that could not be transmitted because of

errors.

Collision Frames The best estimate of the total number of collisions on this Ethernet segment.

Link Down Events The total number of link down events on a physical port.

Time Since Counters Last

Cleared The elapsed time in days, hours, minutes, and seconds since the statistics

for this port were last cleared.

Reset the counters for all interfaces on the switch

To reset the counters for all interfaces on the switch:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Monitoring  Ports > Port Statistics.

The Port Statistics page displays.

6. Select the check box in the heading of the table.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual397

7. Click the Clear button.

All counters are reset to 0.

Reset the counters for one or more interfaces

To reset the counters for one or more interfaces:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Monitoring  Ports > Port Statistics.

The Port Statistics page displays.

6. Select whether to display physical interfaces, LAGs, or both by clicking one of the following

links above the table heading:

•1 (the unit ID of the switch). Only physical interfaces are displayed. This is the default

setting.

•LAG. Only LAGs are displayed.

• All. Both physical interfaces and LAGs are displayed.

7. Select one or more interfaces by taking one of the following actions:

•To reset a single interface, select the check box associated with the port, or type the

port number in the Go To Interface field and click the Go button.

•To reset multiple interfaces, select the check box associated with each interface.

8. Click the Clear button.

The counters for the interface are reset to 0.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual398

View and manage detailed port statistics

You can view a variety of per-port traffic statistics.

To view or clear detailed port statistics:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Monitoring > Ports > Port Detailed Statistics.

The previous figure does not show all fields on the Port Detailed Statistics page.

6. From the Interface menu, select the interface for which you want to view the statistics.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual399

7. From the MST ID menu, select the MST ID associated with the interface (if available).

8. To refresh the page with the latest information about the switch, click the Update button.

9. To clear all the counters, click the Clear button. This resets all statistics for this port to the

default values.

The following table describes the detailed port information displayed on the page. To view

information about a different port, select the port number from the Interface menu.

Table 91. Detailed port statistics

Field Description

ifIndex This object indicates the ifIndex of the interface table entry associated with this

port on an adapter.

Port Type For normal ports this field displays Normal. Otherwise, the possible values are

as follows:

• Mirrored. This port is a participating in port mirroring as a mirrored port.

Look at the Port Mirroring pages for more information.

• Probe. This port is a participating in port mirroring as the probe port. Look

at the Port Mirroring pages for more information.

• Trunk Member. The port is a member of a link aggregation trunk. Look at

the Port Channel pages for more information.

Port Channel ID If the port is a member of a port channel, the port channel’s interface ID and

name are shown. Otherwise, Disable is shown.

Port Role Each MST bridge port that is enabled is assigned a port role for each spanning

tree. The port role is one of the following values: Root, Designated, Alternate,

Backup, Master, or Disabled.

STP Mode The Spanning T ree Protocol administrative mode that is associated with the port

or port channel. The possible values are as follows:

• Enable. Spanning tree is enabled for this port.

• Disable. Spanning tree is disabled for this port.

STP State The port's current Spanning Tree state. This state controls what action a port

takes on receipt of a frame. If the bridge detects a malfunctioning port, it places

that port into the broken state. The states are defined in IEEE 802.1D:

• Disabled

• Blocking

• Listening

• Learning

• Forwarding

• Broken

Admin Mode The port control administration state. The port must be enabled for it to be

allowed into the network. The default is Enabled.

Flow Control Mode Indicates whether flow control is enabled or disabled for the port. This field is not

valid for LAG interfaces.

LACP Mode Indicates the Link Aggregation Control Protocol administrative state. The mode

must be enabled for the port to participate in link aggregation.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual400

Physical Mode Indicates the port speed and duplex mode. In autonegotiation mode the duplex

mode and speed are set from the autonegotiation process.

Physical Status Indicates the port speed and duplex mode.

Link Status Indicates whether the link is up or down.

Link T rap Indicates whether or not the port sends a trap when link status changes.

Packets RX and TX 64

Octets The total number of packets (including bad packets) received or transmitted that

were 64 octets in length (excluding framing bits but including FCS octets).

Packets RX and TX 65-127

Octets The total number of packets (including bad packets) received or transmitted that

were between 65 and 127 octets in length inclusive (excluding framing bits but

including FCS octets).

Packets RX and TX 128-255

Octets The total number of packets (including bad packets) received or transmitted that

were between 128 and 255 octets in length inclusive (excluding framing bits but

including FCS octets).

Packets RX and TX 256-511

Octets The total number of packets (including bad packets) received or transmitted that

were between 256 and 511 octets in length inclusive (excluding framing bits but

including FCS octets).

Packets RX and TX 512-1023

Octets The total number of packets (including bad packets) received or transmitted that

were between 512 and 1023 octets in length inclusive (excluding framing bits

but including FCS octets).

Packets RX and TX

1024-1518 Octets The total number of packets (including bad packets) received or transmitted that

were between 1024 and 1518 octets in length inclusive (excluding framing bits

but including FCS octets).

Packets RX and TX

1519-2047 Octets The total number of packets (including bad packets) received or transmitted that

were between 1519 and 2047 octets in length inclusive (excluding framing bits

but including FCS octets).

Packets RX and TX

2048-4095 Octets The total number of packets (including bad packets) received or transmitted that

were between 2048 and 4095 octets in length inclusive (excluding framing bits

but including FCS octets).

Packets RX and TX

4096-9216 Octets The total number of packets (including bad packets) received or transmitted that

were between 4096 and 9216 octets in length inclusive (excluding framing bits

but including FCS octets).

Octets Received The total number of octets of data (including those in bad packets) received on

the network (excluding framing bits but including FCS octets). This object can be

used as a reasonable estimate of Ethernet utilization. If greater precision is

desired, the etherStatsPkts and etherStatsOctets objects must be sampled

before and after a common interval.

Packets Received 64 Octets The total number of packets (including bad packets) received that were 64

octets in length (excluding framing bits but including FCS octets).

Table 91. Detailed port statistics (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual401

Packets Received 65-127

Octets The total number of packets (including bad packets) received that were between

65 and 127 octets in length inclusive (excluding framing bits but including FCS

octets).

Packets Received 128-255

Octets The total number of packets (including bad packets) received that were between

128 and 255 octets in length inclusive (excluding framing bits but including FCS

octets).

Packets Received 256-511

Octets The total number of packets (including bad packets) received that were between

256 and 511 octets in length inclusive (excluding framing bits but including FCS

octets).

Packets Received 512-1023

Octets The total number of packets (including bad packets) received that were between

512 and 1023 octets in length inclusive (excluding framing bits but including

FCS octets).

Packets Received 1024-1518

Octets The total number of packets (including bad packets) received that were between

1024 and 1518 octets in length inclusive (excluding framing bits but including

FCS octets).

Packets Received > 1518

Octets The total number of packets received that were longer than 1518 octets

(excluding framing bits, but including FCS octets) and were otherwise well

formed.

Total Packets Received

Without Errors The total number of packets received that were without errors.

Unicast Packets Received The number of subnetwork-unicast packets delivered to a higher-layer protocol.

Multicast Packets Received The total number of good packets received that were directed to a multicast

address. This number does not include packets directed to the broadcast

address.

Broadcast Packets Received The total number of good packets received that were directed to the broadcast

address. This does not include multicast packets.

Receive Packets Discarded The number of inbound packets that were discarded even though no errors were

detected to prevent their being delivered to a higher-layer protocol. A possible

reason for discarding a packet could be to free up buffer space.

Total Packets Received with

MAC Errors The total number of inbound packets that contained errors preventing them from

being deliverable to a higher-layer protocol.

Jabbers Received The total number of packets received that were longer than 1518 octets

(excluding framing bits, but including FCS octets), and included either a bad

frame check sequence (FCS) with an integral number of octets (FCS Error) or a

bad FCS with a nonintegral number of octets (alignment error). This definition of

jabber is different from the definition in IEEE-802.3 section 8.2.1.5 (10BASE5)

and section 10.3.1.4 (10BASE2). These documents define jabber as the

condition where any packet exceeds 20 ms. The allowed range to detect jabber

is between 20 ms and 150 ms.

Fragments Received The total number of packets received that were less than 64 octets in length with

ERROR CRC (excluding framing bits but including FCS octets).

Table 91. Detailed port statistics (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual402

Undersize Received The total number of packets received that were less than 64 octets in length with

GOOD CRC (excluding framing bits but including FCS octets).

Alignment Errors The total number of packets received with a length (excluding framing bits, but

including FCS octets) of between 64 and 1518 octets, inclusive, but included a

bad frame check sequence (FCS) with a nonintegral number of octets.

Rx FCS Errors The total number of packets received with a length (excluding framing bits, but

including FCS octets) of between 64 and 1518 octets, inclusive, but included a

bad frame check sequence (FCS) with an integral number of octets.

Overruns The total number of frames discarded because this port was overloaded with

incoming packets, and could not keep up with the inflow.

Total Received Packets Not

Forwarded The number of valid frames received that were discarded (that is, filtered) by the

forwarding process.

802.3x Pause Frames

Received The number of MAC control frames received on this interface with an opcode

indicating the PAUSE operation. This counter does not increment when the

interface is operating in half-duplex mode.

Unacceptable Frame Type The number of frames discarded from this port due to being an unacceptable

frame type.

Total Packets Transmitted

(Octets) The total number of octets of data (including those in bad packets) transmitted

on the network (excluding framing bits but including FCS octets). This object can

be used as a reasonable estimate of Ethernet utilization. If greater precision is

desired, the etherStatsPkts and etherStatsOctets objects must be sampled

before and after a common interval.

Packets T ransmitted 64

Octets The total number of packets (including bad packets) received that were 64

octets in length (excluding framing bits but including FCS octets).

Packets T ransmitted 65-127

Octets The total number of packets (including bad packets) received that were between

65 and 127 octets in length inclusive (excluding framing bits but including FCS

octets).

Packets Transmitted 128-255

Octets The total number of packets (including bad packets) received that were between

128 and 255 octets in length inclusive (excluding framing bits but including FCS

octets).

Packets T ransmitted 256-511

Octets The total number of packets (including bad packets) received that were between

256 and 511 octets in length inclusive (excluding framing bits but including FCS

octets).

Packets T ransmitted

512-1023 Octets The total number of packets (including bad packets) received that were between

512 and 1023 octets in length inclusive (excluding framing bits but including

FCS octets).

Packets T ransmitted

1024-1518 Octets The total number of packets (including bad packets) received that were between

1024 and 1518 octets in length inclusive (excluding framing bits but including

FCS octets).

Table 91. Detailed port statistics (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual403

Packets Transmitted > 1518

Octets The total number of packets transmitted that were longer than 1518 octets

(excluding framing bits, but including FCS octets) and were otherwise well

formed. This counter supports a maximum increment rate of 815 counts per sec

at 10 Mb/s.

Maximum Frame Size The maximum Ethernet frame size the interface supports or is configured to use,

including Ethernet header, CRC, and payload. The possible range is 1518 to

9216. The default maximum frame size is 1518.

Total Packets Transmitted

Successfully The number of frames that were transmitted by this port to its segment.

Unicast Packets Transmitted The total number of packets that higher-level protocols requested be transmitted

to a subnetwork-unicast address, including those that were discarded or not

sent.

Multicast Packets

Transmitted The total number of packets that higher-level protocols requested be transmitted

to a multicast address, including those that were discarded or not sent.

Broadcast Packets

Transmitted The total number of packets that higher-level protocols requested be transmitted

to the broadcast address, including those that were discarded or not sent.

Transmit Packets Discarded The number of outbound packets which were chosen to be discarded even

though no errors were detected to prevent them from being delivered to a

higher-layer protocol. A possible reason for discarding a packet could be to free

up buffer space.

Total Transmit Errors The sum of single, multiple, and excessive collisions.

Total Transmit Packets

Discarded The sum of single collision frames discarded, multiple collision frames

discarded, and excessive frames discarded.

Single Collision Frames The number of successfully transmitted frames on a particular interface for

which transmission is inhibited by exactly one collision.

Multiple Collision Frames The number of successfully transmitted frames on a particular interface for

which transmission is inhibited by more than one collision.

Excessive Collision Frames The number of frames for which transmission on a particular interface fails due

to excessive collisions.

Dropped T ransmit Frames The number of transmit frames discarded at the selected port.

STP BPDUs Received The number of STP BPDUs received at the selected port.

STP BPDUs Transmitted The number of STP BPDUs transmitted from the selected port.

RSTP BPDUs Received The number of RSTP BPDUs received at the selected port.

RSTP BPDUs Transmitted The number of RSTP BPDUs transmitted from the selected port.

MSTP BPDUs Received The number of MSTP BPDUs received at the selected port.

MSTP BPDUs Transmitted The number of MSTP BPDUs transmitted from the selected port.

Table 91. Detailed port statistics (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual404

View or clear EAP and EAPoL statistics

You can view information about Extensible Authentication Protocol (EAP) and EAP over LAN

(EAPoL) packets that are received on physical ports.

To view or clear EAP and EAPoL statistics:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Monitoring > Ports > EAP Statistics.

802.3x Pause Frames

Transmitted The number of MAC control frames transmitted on this interface with an opcode

indicating the PAUSE operation. This counter does not increment when the

interface is operating in half-duplex mode.

GVRP PDUs Received The number of GVRP PDUs received in the GARP layer.

GVRP PDUs Transmitted The number of GVRP PDUs transmitted from the GARP layer.

GVRP Failed Registrations The number of times attempted GVRP registrations could not be completed.

EAPOL Frames Received The number of valid EAPoL frames of any type that were received by this

authenticator.

EAPOL Frames Transmitted The number of EAPoL frames of any type that were transmitted by this

authenticator.

Time Since Counters Last

Cleared The elapsed time in days, hours, minutes, and seconds since the statistics for

this port were last cleared.

Table 91. Detailed port statistics (continued)

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual405

6. To refresh the page with the latest information about the switch, click the Update button.

7. To clear the counters for a specific port, select the check box associated with the port and

click the Clear button.

8. To clear all the EAP counters for all ports on the switch, select the check box in the row

heading and click the Clear button.

Clicking the button resets all statistics for all ports to default values.

The following table describes the EAP statistics displayed on the page.

Table 92. EAP statistics

Field Description

Port The port number.

EAPOL Frames Received The number of valid EAPoL frames of any type that were received by this

authenticator.

EAPOL Frames Transmitted The number of EAPoL frames of any type that were transmitted by this

authenticator.

EAPOL Start Frames

Received The number of EAPoL start frames that were received by this authenticator.

EAPOL Logoff Frames

Received The number of EAPoL logoff frames that were received by this authenticator.

EAPOL Last Frame Version The protocol version number carried in the most recently received EAPoL frame.

EAPOL Last Frame Source The source MAC address carried in the most recently received EAPoL frame.

EAPOL Invalid Frames

Received The number of EAPoL frames that were received by this authenticator in which

the frame type is not recognized.

EAPOL Length Error Frames

Received The number of EAPoL frames that were received by this authenticator in which

the frame type is not recognized.

EAP Response/ID Frames

Received The number of EAP response/identity frames that were received by this

authenticator.

EAP Response Frames

Received The number of valid EAP response frames (other than resp/ID frames) that were

received by this authenticator.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual406

Perform a cable test

You can test and view information about the cables that are connected to switch ports.

To perform a cable test:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Monitoring > Ports > Cable Test.

6. Select the check boxes that are associated with the physical ports for which you want to test

the cables.

7. Click the Apply button.

A cable test is performed on all selected ports. The cable test might take up to two

seconds to complete. If the port forms an active link with a device, the cable status is

always Normal. The test returns a cable length estimate if this feature is supported by the

EAP Request/ID Frames

Transmitted The number of EAP request/identity frames that were transmitted by this

authenticator.

EAP Request Frames

Transmitted The number of EAP request frames (other than request/identity frames) that

were transmitted by this authenticator.

Table 92. EAP statistics

Field Description

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual407

PHY for the current link speed. Note that if the link is down and a cable is attached to a

10/100 Ethernet adapter then the cable status might be Open or Short because some

Ethernet adapters leave unused wire pairs unterminated or grounded.

The following table describes the nonconfigurable information displayed on the page.

Table 93. Cable Test information

Field Description

Cable Status Indicates the cable status:

Cable Length The estimated length of the cable in meters. The length is displayed as a range

between the shortest estimated length and the longest estimated length.

Unknown is displayed if the cable length could not be determined. The cable

length is displayed only if the cable status is Normal.

Failure Location The estimated distance in meters from the end of the cable to the failure

location. The failure location is displayed only if the cable status is Open or

Short.

Configure and view the logs

The switch generates messages in response to events, faults, or errors occurring on the

platform as well as changes in configuration or other occurrences. These messages are

stored locally and can be forwarded to one or more centralized points of collection for

monitoring purposes or long-term archival storage. Local and remote configuration of the

logging capability includes filtering of messages logged or forwarded based on severity and

generating component.

Manage and view the memory log

The memory log stores messages in memory based upon the settings for message

component and severity. You can set the administrative status and behavior of logs in the

system buffer. These log messages are cleared when the switch reboots.

For the message log, only the latest 200 entries are displayed on the page.

• Normal. The cable is working correctly.

• Open. The cable is disconnected or a faulty connector exists.

• Short. An electrical short exists in the cable.

• Cable Test Failed. The cable status could not be determined. The cable

might in fact be working.

• Untested. The cable is not yet tested.

• Invalid cable type. The cable type is unsupported.

• No cable. The cable is not present.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual408

To manage and view the memory log:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Monitoring > Logs > Memory Log.

The Memory Log page displays.

6. Select one of the following Admin Status radio buttons:

•Enable. Enable system logging.

• Disable. Prevent the system from logging messages.

7. From the Behavior menu, specify the behavior of the log when it is full.

• Wrap. When the buf fer is full, the oldest log messages are deleted as the system logs

new messages.

•Stop on Full. When the buffer is full, the system stops logging new messages and

preserves all existing log messages.

8. From the Severity Filter menu, select one of the following severity levels:

• Emergency (0). System is unusable.

• Alert (1). Action must be taken immediately.

• Critical (2). Critical conditions.

• Error (3). Error conditions.

• Warning (4). Warning conditions.

•Notice (5). Normal but significant conditions.

• Informational (6). Informational messages.

• Debug (7). Debug-level messages.

Note: A log records messages equal to or above a configured severity

threshold.

9. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual409

The Memory Log table displays on the Memory Log page.

The Total number of Messages field displays the number of messages the system logged

in memory. Only the 200 most recent entries are displayed on the page.

The rest of the page displays the Memory Log messages. The format of the log message

is the same for messages that are displayed for the message log, persistent log, or

console log. Messages logged to a collector or relay through syslog support the same

format as well.

The following example shows the standard format for a log message:

<14> Mar 24 05:34:05 10.131.12.183-1 UNKN[2176789276]:

main_login.c(179) 3855 %% HTTP Session 19 initiated for user admin

connected from 10.27.64.122

The number contained in the angle brackets represents the message priority, which is

derived from the following values:

Priority = (facility value × 8) + severity level.

The facility value is usually 1, which means it is a user-level message. Therefore, to

determine the severity level of the message, subtract 8 from the number in the angle

brackets. The sample log message shows a severity level of 6 (informational). For more

information about the severity of a log message, see Manage the server log on

page 412.

The message was generated on March 24 at 5:34:05 a.m. by the switch with an IP

address of 10.131.12.183. The component that generated the message is unknown, but it

came from line 179 of the main_login.c file. This is the 3,855th message logged since

the switch was last booted. The message indicates that the administrator logged on to the

HTTP local browser interface from a host with an IP address of 10.27.64.122.

10. To refresh the page with the latest information about the switch, click the Update button.

11. To clear the messages from the buffered log in the memory, click the Clear button.

Message log format

This topic applies to the format of all logged messages that are displayed for the message

log, persistent log, or console log.

Messages logged to a collector or relay through syslog use an identical format:

•<15>Aug 24 05:34:05 0.0.0.0-1 MSTP[2110]: mspt_api.c(318) 237%%

Interface 12 transitioned to root state on message age timer

expiry.

This example indicates a message with severity 7 (15 mod 8) (debug) on a chassis and

generated by component MSTP running in thread ID 2110 on Aug 24 05:34:05 by line

318 of file mstp_api.c. This is the 237th message logged with system IP 0.0.0.0 and

task-ID 1.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual410

•<15>Aug 24 05:34:05 STK0 MSTP[2110]: mspt_api.c(318) 237%%

Interface 12 transitioned to root state on message age timer

expiry.

This example indicates a user-level message (1) with severity 7 (debug) on a system that

is not a chassis and generated by component MSTP running in thread ID 2110 on Aug 24

05:34:05 by line 318 of file mstp_api.c. This is the 237th message logged. Messages

logged to a collector or relay through syslog use a format identical to the previous

message.

Manage and view the flash log

The flash log is a persistent log, that is, is a log that is stored in persistent storage. Persistent

storage survives across platform reboots. The first log type is the system startup log. The

system startup log stores the first 32 messages received after system reboot. The second log

type is the system operation log. The system operation log stores messages received during

system operation.

To manage and view the flash log:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Monitoring > Logs > FLASH Log.

The FLASH Log Configuration page displays.

6. Select one of the following Admin Status radio buttons:

•Enable. A log that is enabled logs messages.

•Disable. A log that is disabled does not log messages.

7. From the Severity Filter menu, select the logging level for messages that must be sent to

the logging host.

Log messages with the selected severity level and all log messages of greater severity

are sent to the host. For example, if you select Error, the logged messages include Error ,

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual411

Critical, Alert, and Emergency. The default severity level is Alert (1). The severity can be

one of the following levels:

- Emergency (0). The highest warning level. If the device is down, or not

functioning properly, an emergency log message is saved to the device.

- Alert (1). The second-highest warning level. An alert log message is saved if a

serious device malfunction occurs, such as all device features being down. Action

must be taken immediately.

- Critical (2). The third-highest warning level. A critical log message is saved if a

critical device malfunction occurs, for example, two device ports are not

functioning, while the rest of the device ports remain functional.

- Error (3). A device error occurred, such as a port being offline.

- Warning (4). The lowest level of a device warning.

-Notice (5). Normal but significant conditions. Provides the network administrators

with device information.

- Informational (6). Provides device information.

- Debug (7). Provides detailed information about the device.

8. From the Logs to be Displayed menu, select one of the following options:

• Current Logs. The log messages for the current switch sessions are displayed. This

is the default setting.

• Previous Logs. The previous log messages are displayed, that is, the log messages

that are still in the flash memory from before the switch was rebooted.

9. Click the Apply button.

Your settings are saved.

The Total Number of Messages field shows is the total number of persistent log

messages that are stored on the switch. The maximum number of persistent log

messages displayed on the switch is 64.

Description: <15>Aug 24 05:34:05 STK0 MSTP[2110]: mspt_api.c(318)

237 %% Interface 12 transitioned to root state on message age

timer expiry

The previous log message example indicates a user-level message (1) with severity 7

(debug) on a system that is not stacked and generated by component MSTP running in

thread ID 2110 on Aug 24 05:34:05 by line 318 of file mstp_api.c. This is the 237th

message logged. Messages logged to a collector or relay via syslog support an identical

format as the previous message.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual412

Manage the server log

You can let the switch send log messages to remote logging hosts. A remote log server is the

same as a remote syslog host.

You must enable the server log on the switch and specify one or more remote syslog hosts.

Enable the server log and add a remote syslog host

To enable the server log and add a remote syslog host:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Monitoring > Logs > Server Log.

The Server Log page displays.

6. Select one of the following Admin Status radio buttons:

•Enable. Send log messages to all configured hosts (syslog collectors or relays) using

the values configured for each host.

• Disable. Stop logging to all syslog hosts. Disable means no messages are sent to

any collector or relay.

7. In the Local UDP Port field, specify the port on the switch from which syslog messages

must be sent. The Local UDP port values are 1 to 65535.

8. Click the Apply button.

Your settings are saved.

9. In the Server Configuration section, specify the following settings:

• IP Address Type. Specify the IP address type of the host, which can be IPv4, IPv6,

or DNS.

• Host Address. Specify the IP address or host name of the syslog host.

• Port. Specify the port on the host to which syslog messages must be sent. The

default port number is 514.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual413

• Severity Filter. Use the menu to select the severity of the logs that must be sent to

the logging host. Logs with the selected severity level and all logs of greater severity

are sent to the host. For example, if you select Error, the logged messages include

Error, Critical, Alert, and Emergency. The default severity level is Alert (1). The

severity can be one of the following levels:

- Emergency (0). The highest warning level. If the device is down or not

functioning properly, an emergency log is saved to the device.

- Alert (1). The second-highest warning level. An alert log is saved if a serious

device malfunction occurs, such as all device features being down.

- Critical (2). The third-highest warning level. A critical log is saved if a critical

device malfunction occurs, for example, two device ports are not functioning,

while the rest of the device ports remain functional.

- Error (3). A device error occurred, such as a port being offline.

- Warning (4). The lowest level of a device warning.

-Notice (5). Provides the network administrators with device information.

- Informational (6). Provides device information.

- Debug (7). Provides detailed information about the log.

10. Click the Add button.

The remote syslog host is added.

The Status field in the Server Configuration table shows whether the remote logging host

is currently active.

The Server Log Configuration section displays the following information:

•The Messages Received field shows the number of messages received by the log

process. This includes messages that are dropped or ignored.

•The Messages Relayed field shows the number of messages forwarded by the

syslog function to a syslog host. Messages forwarded to multiple hosts are counted

once for each host.

•The Messages Ignored field shows the number of messages that were ignored.

Modify the settings for a remote syslog host

To modify the settings for a remote syslog host:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual414

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Monitoring > Logs > Server Log.

The Server Log Configuration page displays.

6. Select the check box that is associated with the host.

7. Change the information as needed.

8. Click the Apply button.

Your settings are saved.

Delete the settings for a remote syslog host

To delete the settings for a remote syslog host:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Monitoring > Logs > Server Log.

The Server Log Configuration page displays.

6. Select the check box that is associated with the host.

7. Click the Delete button.

The host is removed.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual415

View or clear the trap logs and the counters

You can view information about the SNMP traps generated on the switch.

You can also display information about the traps that were sent.

To view or clear the trap logs and the counters:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Monitoring > Logs > Trap Logs.

6. To clear all counters, click the Clear button.

All statistics for the trap logs are reset to their default values.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual416

The following table describes the Trap Log information that is displayed on the page.

Table 94. Trap Logs information

Field Description

Number of Traps Since Last

Reset The number of traps that occurred since the switch last rebooted.

Trap Log Capacity The maximum number of traps stored in the log. If the number of traps exceeds

the capacity, the entries overwrite the oldest entries.

Number of Traps since log

last viewed The number of traps that occurred since the traps were last displayed.

Displaying the traps by any method (terminal interface display, web display,

upload file from switch, and so on) causes this counter to be cleared to 0.

Log The sequence number of this trap.

System Up Time The time when this trap occurred, expressed in days, hours, minutes, and

seconds, since the last reboot of the switch.

Trap Information identifying the trap.

View or clear the event log

You can display the event log, which is used to hold error messages for catastrophic events.

After the event is logged and the updated log is saved in flash memory, the switch is reset.

The log can hold at least 2,000 entries and is erased when an attempt is made to add an

entry after it is full. The event log is preserved across system resets.

To view or clear the event log:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Monitoring > Logs > Event Logs.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual417

6. To refresh the page with the latest information about the switch, click the Update button.

7. To clear the messages from the event Log, click the Clear button.

The following table describes the event log information that is displayed on the page.

Table 95. Event Logs information

Field Description

Entry The sequence number of the event.

Type The type of the event.

File Name The file in which the event originated.

Line The line number of the event.

Task Id The task ID of the event.

Code The event code.

Time The time this event occurred.

Format of the messages

Messages are displayed in the following format:

•Total number of messages: Number of persistent log messages displayed on the

switch.

•<15>Aug 24 05:34:05 STK0 MSTP[2110]: mspt_api.c(318) 237%%

Interface 12 transitioned to root state on message age timer

expiry

This example indicates a user-level message (1) with severity 7 (debug) on a system that is

not a chassis and generated by component MSTP running in thread ID 2110 on Aug 24

05:34:05 by line 318 of file mstp_api.c. This is the 237th message logged. Messages

logged to a collector or relay through syslog use a format identical to the previous message.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual418

Configure port mirroring

Port mirroring selects the network traffic for analysis by a network analyzer. This is done for

specific ports of the switch. As such, many switch ports are configured as source ports and

one switch port is configured as a destination port. You can configure how traffic is mirrored

on a source port. Packets that are received on the source port, that are transmitted on a port,

or are both received and transmitted can be mirrored to the destination port.

The packet that is copied to the destination port is in the same format as the original packet

on the wire. This means that if the mirror is copying a received packet, the copied packet is

VLAN tagged or untagged as it was received on the source port. If the mirror is copying a

transmitted packet, the copied packet is VLAN tagged or untagged as it is being transmitted

on the source port.

The Port Mirroring page allows you to view and configure port mirroring on the system.

To globally enable port mirroring, specify the destination port, and specify one or

more source ports:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Monitoring > Mirroring > Port Mirroring.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Monitor the Switch and the Traffic User Manual419

6. Select an Admin Mode radio button:

• True. Port mirroring is enabled.

• False. Port mirroring is enabled.

7. From the Destination Port menu, select the destination port to which port traffic must be

copied.

You can configure only one destination port on the system. The port functions as a probe

port and receives traffic from all configured source ports. If no port is configured, None is

displayed. The default is None.

8. Click the Apply button.

Your settings are saved.

The following steps must be performed in the Source Interface Configuration section.

9. Use one of the following methods to narrow down the ports that are displayed:

•Select Unit ID to display the physical ports of the selected unit.

•Select LAG to display a list of LAGs only.

•Select CPU to display a list of CPUs only.

•Select All to display a list of all physical ports, LAGs, CPUs, and VLANs.

10. Select one or more interfaces by taking one of the following actions:

•To configure a single interface, select the check box associated with the port, or type

the port number in the Go To Interface field and click the Go button.

•To configure multiple interfaces with the same settings, select the check box

associated with each interface.

Traffic from the selected ports is sent to the probe port.

11. From the Direction menu, specify the direction of the traffic that must be mirrored from the

selected source ports:

•None. The value is not configured. This is the default setting.

•Tx and Rx. Monitors transmitted and received packets.

•Rx. Monitors received (ingress) packets only.

•T

x. Monitors transmitted (egress) packets only.

12. Click the Apply button.

Your settings are saved.

The Status field indicates the interface status.

420

8Maintain or Troubleshoot the

Switch

This chapter covers the following topics:

•Reboot the switch

•Reset the switch to its factory default settings

•Export a file from the switch

•Download a file to the switch or update the software

•Manage software images

•Perform diagnostics and troubleshooting

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual421

Reboot the switch

You can reboot the switch from the local browser interface.

To reboot the switch:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Maintenance > Reset > Device Reboot.

6. Select the check box.

7. Click the Apply button.

The switch reboots.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual422

Reset the switch to its factory default

settings

You can reset the system configuration to the factory default values. All changes that you

made are lost. If the IP address changes, your web session might disconnect.

Note: If you reset the switch to the default configuration, the IP address is

reset to 192.168.0.239, and the DHCP client is enabled. If you lose

network connectivity after you reset the switch to the factory defaults,

see Change the default IP address of the switch on page 13.

To reset the switch to the factory default settings:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Maintenance > Reset > Factory Default.

6. Select the check box.

7. Click the Apply button.

A confirmation pop-up window opens.

8. Click the Yes button to confirm.

All configuration settings are reset to their factory default values. All changes that you

made are lost, even if you saved the configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual423

Export a file from the switch

You can export configuration (ASCII or log ASCII) files from the switch to a file server by

using TFTP or HTTP. Model GS418TPP also lets you use USB.

The following sections describe how you can export a file from the switch:

•Use TFTP to export a file from the switch to a TFTP server on page 423

•Use HTTP to export a file from the switch to a computer on page 425

•Export a file from the switch to a USB device on page 426

Use TFTP to export a file from the switch to a TFTP server

You can upload (export) configuration (ASCII or log ASCII) files from the switch to a TFTP

server on the network.

To export a file from the switch to a TFTP server:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Maintenance > Export > TFTP File Export.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual424

6. From the File Type menu, select the type of file:

• Text Configuration. A text-based configuration file enables you to edit a configured

text file (startup-config) offline as needed. The most common usage of

text-based configuration is to upload a working configuration from a device, edit it

offline to personalize it for another similar device (for example, change the device

name or IP address), and download it to that device.

• Error Log. The system error (persistent) log, also referred to as the event log.

•Trap Log. The trap log with the system trap records.

•Buffered Log. The system buffered (in-memory) log.

• Tech Support. The tech support file is a text-base file that contains a variety of

hardware, software, and configuration information that can assist in device and

network troubleshooting.

•Crash Logs. Specify the crash logs to retrieve them.

7. From the Server Address Type menu, select the format for the Server Address field:

• IPv4. Indicates that the TFTP server address is an IP address in dotted-decimal

format. This is the default setting.

• DNS. Indicates that the TFTP server address is a host name.

8. In the Server Address field, enter the IP address of the server in accordance with the

format indicated by the server address type.

The default is the IPv4 address 0.0.0.0.

9. In the Transfer File Path field, specify the path on the TFTP server where you want to save

the file.

You can enter up to 32 characters. Include the backslash at the end of the path. A path

name with a space is not accepted. Leave this field blank to save the file to the root TFTP

directory.

10. In the Transfer File Name field, specify a destination file name for the file to be uploaded.

You can enter up to 32 characters. The transfer fails if you do not specify a file name. For

an archive transfer, use a .stk file extension.

11. Select the Start File Transfer check box.

12. Click the Apply button.

The file transfer begins.

The page displays information about the file transfer progress. The page refreshes

automatically when the file transfer completes (or if it fails).

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual425

Use HTTP to export a file from the switch to a computer

You can upload (export) files of various types from the switch to a computer through an

HTTP session by using your web browser.

To export a file from the switch to a computer by using HTTP:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Maintenance > Export > HTTP File Export.

6. From the File Type menu, select the type of file:

• Text Configuration. A text-based configuration file enables you to edit a configured

text file (startup-config) offline as needed. The most common usage of

text-based configuration is to upload a working configuration from a device, edit it

offline to personalize it for another similar device (for example, change the device

name or IP address), and download it to that device.

• Tech Support. The tech support file is a text-base file that contains a variety of

hardware, software, and configuration information that can assist in device and

network troubleshooting.

• Crash Logs. Specify crash logs to retrieve them.

7. Click the Apply button.

The file transfer begins.

The page displays information about the file transfer progress. The page refreshes

automatically when the file transfer completes (or if it fails).

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual426

Export a file from the switch to a USB device

Note: Model GS418TPP supports a USB device. Models GS519TLP and

GS510TPP do not.

You can upload (export) a configuration file from the switch to a USB device.

To export a file from the switch to a USB device:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Maintenance > Export > USB File Export.

6. From the File Type menu, select the type of file:

• Text Configuration. A text-based configuration file enables you to edit a configured

text file (startup-config) offline as needed. The most common usage of

text-based configuration is to upload a working configuration from a device, edit it

offline to personalize it for another similar device (for example, change the device

name or IP address), and download it to that device.

7. In the File Path field, enter the path for the file to upload.

You can use up to 146 characters. The default is blank.

8. In the USB File field, enter a name along with path for the file to upload.

You can enter up to 32 characters. The default is blank.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual427

9. Click the Apply button.

The file transfer begins.

The page displays information about the file transfer progress. The page refreshes

automatically when the file transfer completes (or if it fails).

Download a file to the switch or update the

software

You can download system files from a remote system to the switch by using either TFTP or

HTTP.

The following sections describe how you can download a file to the switch:

•Use TFTP to download a file to the switch or update the software image on page 427

•Use HTTP to download a file to the switch or update the software image on page 429

•Download a file from a USB device on page 431

Note: Use one of these procedures to update the software (firmware) on the

switch.

Use TFTP to download a file to the switch or update the

software image

You can download device software, the image file, the configuration files, and SSL files from

a TFTP server to the switch.

Before you download a file to the switch, the following conditions must be true:

•The file to download from the TFTP server is on the server in the appropriate directory.

•The file is in the correct format.

•The switch contains a path to the TFTP server.

You can also download files by using HTTP. See Use HTTP to download a file to the switch

or update the software image on page 429 for additional information.

To download a file to the switch from a TFTP server:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual428

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Maintenance > Download > TFTP File Download.

6. From the File Type menu, select the type of file:

• Software. The system software image, which is saved in one of two flash sectors

called images (image1 and image2). The active image stores the active copy, while

the other image stores a second copy. The device boots and runs from the active

image. If the active image is corrupted, the system automatically boots from the

nonactive image. This is a safety feature for faults occurring during the boot upgrade

process. The default setting is Archive.

• Text Configuration. A text-based configuration file enables you to edit a configured

text file (startup-config) offline as needed. The most common usage of

text-based configuration is to upload a working configuration from a device, edit it

offline to personalize it for another similar device (for example, change the device

name or IP address), and download it to that device.

• SSL Trusted Root Certificate PEM File. SSL Trusted Root Certificate File (PEM

Encoded).

•SSL Server Certificate PEM File. SSL Server Certificate File (PEM Encoded).

• SSL DH Weak Encryption Parameter PEM File. SSL Diffie-Hellman Weak

Encryption Parameter File (PEM Encoded).

•SSL DH Strong Encryption Parameter PEM File. SSL Diffie-Hellman Strong

Encryption Parameter File (PEM Encoded).

7. If the selection from the File Type menu is Archive, the Image Name menu is displayed

and you must select the software image that must be downloaded to the switch:

•image1. Select image1 to upload image1.

• image2. Select image2 to upload image2.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual429

Note: We recommended that you do not overwrite the active image. If you do

so, the switch displays a warning that you are trying to overwrite the

active image.

8. From the Server Address Type menu, select the format for the TFTP Server IP field:

• IPv4. Indicates that the TFTP server address is an IP address in dotted-decimal

format. This is the default setting.

• DNS. Indicates that the TFTP server address is a host name.

9. In the TFTP Server IP field, enter the IP address of the TFTP server indicated by the server

address type.

The default is the IPv4 address 0.0.0.0.

10. In the Transfer File Path field, specify the path on the TFTP server where the file is located.

Enter up to 160 characters. Include the backslash at the end of the path. A path name

with a space is not accepted. Leave this field blank to save the file to the root TFTP

directory.

11. In the Remote File Name field, specify the name of the file to download from the TFTP

server.

You can enter up to 32 characters. A file name with a space is not accepted.

12. Select the Start File Transfer check box to initiate the file upload.

13. Click the Apply button.

The file transfer begins.

The page displays information about the progress of the file transfer. The page refreshes

automatically when the file transfer completes (or if it fails).

Use HTTP to download a file to the switch or update the

software image

You can download a software (firmware) image, configuration files, and SSL files from a

computer to the switch by using an HTTP session over a web browser.

To download a file to the switch using HTTP:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual430

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Maintenance > Download > HTTP File Download.

6. From the File Type menu, select the type of file:

• Software. The system software image, which is saved in one of two flash sectors

called images (image1 and image2). The active image stores the active copy, the

other image stores a second copy. The device boots and runs from the active image.

If the active image is corrupted, the system automatically boots from the nonactive

image. This is a safety feature for faults occurring during the boot upgrade process.

The default setting is Archive.

• Text Configuration. A text-based configuration file enables you to edit a configured

text file (startup-config) offline as needed. The most common usage of

text-based configuration is to upload a working configuration from a device, edit it

offline to personalize it for another similar device (for example, change the device

name, serial number, IP address), and download it to that device.

• SSL Trusted Root Certificate PEM File. SSL Trusted Root Certificate File (PEM

Encoded).

•SSL Server Certificate PEM File. SSL Server Certificate File (PEM Encoded).

• SSL DH Weak Encryption Parameter PEM File. SSL Diffie-Hellman Weak

Encryption Parameter File (PEM Encoded).

•SSL DH Strong Encryption Parameter PEM File. SSL Diffie-Hellman Strong

Encryption Parameter File (PEM Encoded).

7. If the selection from the File Type menu is Archive, the Image Name menu is displayed

and you must select the software image that must be downloaded to the switch:

•image1. Select image1 to upload image1.

• image2. Select image2 to upload image2.

Note: We recommended that you do not overwrite the active image. If you do

so, the switch displays a warning that you are trying to overwrite the

active image.

8. Select the Select File Browse button and locate the file that you want to download.

The file name can contain up to 80 characters.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual431

9. Click the Apply button.

The file transfer begins.

The page displays information about the progress of the file transfer . After a file transfer is

started, wait until the page refreshes. When the page refreshes, the option to select a file

option is no longer available, indicating that the file transfer is complete.

Note: After you download a text configuration file, the switch applies the

configuration automatically.

10. After you download a software image file, if you want the switch to run the software image,

do the following:

a. Select the new software image file (see Change the software image that loads when

the switch starts or reboots on page 434).

b. Reboot the switch (see Reboot the switch on page 421).

Download a file from a USB device

Note: Model GS418TPP supports a USB device. Models GS519TLP and

GS510TPP do not.

You can download a file from a USB device to the switch.

To download a file from a USB device:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Maintenance > Download > USB File Download.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual432

6. From the File Type menu, select the type of file:

• Software. The system software image, which is saved in one of two flash sectors

called images (image1 and image2). The active image stores the active copy, the

other image stores a second copy. The device boots and runs from the active image.

If the active image is corrupted, the system automatically boots from the nonactive

image. This is a safety feature for faults occurring during the boot upgrade process.

The default setting is Archive.

• Text Configuration. A text-based configuration file enables you to edit a configured

text file (startup-config) offline as needed. The most common usage of

text-based configuration is to upload a working configuration from a device, edit it

offline to personalize it for another similar device (for example, change the device

name, serial number, IP address), and download it to that device.

7. The Image Name field is visible only when the selection from the File Type menu is

Archive.

If you are downloading a switch image (Archive), use the Image Name list to select the

software image, image1 or image2, to download to the switch.

8. In the File Path field, enter the path for the file to be downloaded.

You can enter up to 146 characters. The default is blank.

9. In the USB File field, specify the path and file name for the file that you want to download.

You can enter up to 32 characters. The default is blank.

Note: We recommended that you do not overwrite the active image. If you do

so, the switch displays a warning that you are trying to overwrite the

active image.

10. Click the Apply button.

The file transfer begins.

The page displays information about the progress of the file transfer. The page refreshes

automatically when the file transfer completes (or if it fails).

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual433

Manage software images

The switch maintains two versions of the switch software in permanent storage. One image is

the active image, and the second image is the backup image. The active image is loaded

when the switch starts or reboots. This feature reduces switch down time when you are

updating the switch software.

Note: A switch that runs an older (legacy) software version might not load a

configuration file that is created by a newer software version. In such

a situation, the switch displays a warning.

The following sections describe how you can manage the software images:

•Copy a software image on page 433

•Configure dual image settings on page 434

•View the dual image status on page 436

Copy a software image

You can copy an image from one location (primary or backup) to another.

To copy a software image:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Maintenance > File Management > Copy.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual434

6. Select the Source Image image1 or image2 radio button to specify the image to be copied.

7. Select the Destination Image image1 or image2 radio button to specify the destination

image.

8. Click the Apply button.

Your settings are saved.

Configure dual image settings

The Dual Image feature allows the switch to retain two images in permanent storage. You

can select which image to load during the next boot cycle, configure an image description, or

delete an image. This feature reduces switch down time when you are upgrading or

downgrading the software image.

Change the software image that loads when the switch starts or reboots

To change the image that loads during the boot process:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Maintenance > File Management > Dual Image Configuration.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual435

6. From the Image Name menu, select the image that is not the image displayed in the

Current-active field.

The Current-active field displays the name of the active image.

7. To specify a name for the selected image, enter one in the Image Description field.

8. Select the Activate Image check box.

9. Click the Apply button.

Your settings are saved.

Note: After activating an image, you must perform a system reset of the

switch to run the new code. The switch continues running the image

shown in the Current-active field until the switch reboots.

Delete a software image

To delete a software image:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Maintenance > File Management > Dual Image Configuration.

The Dual Image Configuration page displays.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual436

6. From the Image Name menu, select the image that is not the image displayed in the

Current-active field.

The Current-active field displays the name of the active image. You cannot delete the

active image.

7. Select the Delete Image check box.

8. Click the Apply button.

The image is removed.

View the dual image status

The Dual Image Status page shows information about the active and backup images on the

system.

To view dual image status information:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Maintenance > File Management > Dual Image > Dual Image Status.

The following table describes the information available on the page.

Table 96. Dual Image Status information

Field Description

Image1 Ver The version of the image1 code file.

Image2 Ver The version of the image2 code file.

Current-active The currently active image on this switch.

Next-active The image to be used on the next restart of this switch.

Image1 Description The description associated with the image1 code file.

Image2 Description The description associated with the image2 code file.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual437

Perform diagnostics and troubleshooting

You can send a ping or a traceroute, and you can perform a memory dump.

Ping an IPv4 address

You can configure the switch to send a ping request to a specified IPv4 address. You can use

this option to check whether the switch can communicate with a particular IPv4 device. When

you send a ping, the switch sends a specified number of ping requests and the results are

displayed.

If a reply to the ping is received, the following message displays:

PING x.y.z.w (x.y.z.w): size data bytes

size bytes from x.y.z.w: seq=0 ttl=xyz

--- x.y.z.w ping statistics ---

count packets transmitted, count packets received, x% packet loss

If a reply to the ping is not received, the following message displays:

PING x.y.z.w (x.y.z.w): size data bytes

--- x.y.z.w ping statistics ---

count packets transmitted, 0 packets received, 100% packet loss

To ping an IPv4 address:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Maintenance > Troubleshooting > Ping IPv4.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual438

6. In the IP Address/Host Name field, enter the IP address or host name of the device that

must be pinged.

7. In the Count field, enter the number of echo requests that must be sent.

The default value is 3. The range is 1 to 15.

8. In the Interval field, enter the time between ping packets in seconds.

The default value is 3 seconds. The range is 1 to 60.

9. In the Size field, enter the size of the ping packet. The default value is 0 bytes. The range is

0 to 13000.

10. From the Source menu, select the IP address or interface that must be used to send echo

request packets:

• None. The source address of the ping packet is the address of the default egress

interface.

• IP Address. The source IP address that must be used when echo request packets

are sent. With this selection, the IP Address field displays and you must enter the IP

address that must be used as the source.

• Interface. The interface that must be used when echo request packets are sent. With

this selection, the Interface menu displays and you must select an interface as the

source.

11. Click the Apply button.

The specified address is pinged. The results are displayed below the configurable data in

the Results field.

Ping an IPv6 address

You can configure the switch to send a ping request to a specified IPv6 address. You can use

this option to check whether the switch can communicate with a particular IPv6 device. When

you send a ping, the switch sends a specified number of ping requests and the results are

displayed.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual439

If a reply to the ping is received, the following message displays:

PING x:y::z:w (x:y::z:w): size data bytes

size bytes from x:y::z:w: seq=0 ttl=xyz

--- x:y::z:w ping statistics ---

count packets transmitted, count packets received, x% packet loss

If a reply to the ping is not received, the following message displays:

PING x:y::z:w (x:y::z:w): size data bytes

--- x:y::z:w ping statistics ---

count packets transmitted, 0 packets received, 100% packet loss

To ping an IPv6 address:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Maintenance > Troubleshooting > Ping IPv6.

6. From the Ping menu, select the type of ping:

• Global. Pings a global IPv6 address.

• Link Local. Pings a link-local IPv6 address over a specified interface. With this

selection, the Interface menu displays, and you must select the interface.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual440

7. In the IPv6 Address/Hostname field, enter the IPv6 address or host name of the station

that must be pinged.

The format is xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx. The maximum number of

characters is 255.

8. In the Count field, enter the number of echo requests that must be sent.

The range is 1 to 15. The default value is 3.

9. In the Interval field, enter the time in seconds between ping packets.

The range is 1 to 60. The default value is 3.

10. In the Datagram Size field, enter the datagram size.

The valid range is 0 to 13000. The default value is 0 bytes.

11. From the Source menu, select the IP address or interface that must be used to send echo

request packets:

• None. The source address of the ping packet is the address of the default egress

interface.

• IPv6 Address. The source IP address that must be used when echo request packets

are sent. With this selection, the IPv6 Address field displays and you must enter the

IPv6 address that must be used as the source.

• Interface. The interface that must be used when echo request packets are sent. With

this selection, the Interface menu displays and you must select an interface as the

source.

12. Click the Apply button.

The specified address is pinged. The results are displayed below the configurable data in

the Results field.

Send an IPv4 traceroute

You can configure the switch to send a traceroute request to a specified IPv4 address or host

name. You can use this to discover the paths that packets take to a remote destination.

When you send a traceroute, the switch displays the results below the configurable data.

If a reply to the traceroute is received, the following message displays:

traceroute to x.y.z.w (x.y.z.w), maxTTL hops max, size byte packets

initTTL x.y.z.w (x.y.z.w) 0.000 ms * 0.000 ms

initTTL+1 x.y.z.w (x.y.z.w) 0.000 ms * 0.000 ms

initTTL+2 x.y.z.w (x.y.z.w) 0.000 ms * 0.000 ms

To send an IPv4 traceroute:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual441

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Maintenance > Troubleshooting > Traceroute IPv4.

6. In the IP Address/Hostname field, enter the IP address or host name of the device for

which the path must be discovered.

7. In the Probes Per Hop field, enter the number of probes per hop.

The default value is 3. The range is 1 to 10.

8. In the Max TTL field, enter the maximum time to live (TTL) for the destination.

The default value is 30. The range is 1 to 255.

9. In the Init TTL field, enter the initial TTL to be used.

The default value is 1. The range is 1 to 255.

10. In the MaxFail field, enter the maximum number of failures allowed in the session.

The default value is 5. The range is 1 to 255.

11. In the Interval (secs) field, enter the time between probes in seconds.

The default value is 3. The range is 1 to 60.

12. In the Port field, enter the UDP destination port for the probe packets.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual442

The default value is 33434. The range is 1–65535.

13. In the Size field, enter the size of the probe packets.

The default value is 0. The range is 0 to 39936.

14. From the Source menu, select the IP address or interface that must be used to send echo

request packets:

• None. The source address for the traceroute is the address of the default egress

interface.

•IP Address. The source IP address that must be used for the traceroute. With this

selection, the IP Address field displays and you must enter the IP address that must

be used as the source.

• Interface. The interface that must be used for the traceroute. With this selection, the

Interface menu displays and you must select an interface as the source.

15. Click the Apply button.

A traceroute request is sent to the specified IP address or host name. The results are

displayed below the configurable data in the Results field.

Send an IPv6 traceroute

You can configure the switch to send a traceroute request to a specified IPv6 address or host

name. You can use this to discover the paths that packets take to a remote destination.

When you send a traceroute, the switch displays the results below the configurable data.

If a reply to the traceroute is received, the following message displays:

traceroute to x:y::z:w (x:y::z:w), maxTTL hops max, size byte packets

initTTL x:y::z:w (x:y::z:w) 0.000 ms * 0.000 ms

initTTL+1 x:y::z:w (x:y::z:w) 0.000 ms * 0.000 ms

initTTL+2 x:y::z:w (x:y::z:w) 0.000 ms * 0.000 ms

To send an IPv6 traceroute:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual443

The System Information page displays.

5. Select Maintenance > Troubleshooting > Traceroute IPv6.

6. In the IPv6 Address/Host Name field, enter the IPv6 address or host name of the device for

which the path must be discovered.

7. In the Probes Per Hop field, enter the number of probes per hop.

The default value is 3. The range is 1 to 10.

8. In the Max TTL field, enter the maximum time to live (TTL) for the destination.

The default value is 30. The range is 1 to 255.

9. In the Init TTL field, enter the initial TTL to be used.

The default value is 1. The range is 1 to 255.

10. In the MaxFail field, enter the maximum number of failures allowed in the session.

The default value is 5. The range is 1 to 255.

11. In the Interval (secs) field, enter the time between probes in seconds.

The default value is 3. The range is 1 to 60.

12. In the Port field, enter the UDP destination port for the probe packets.

The default value is 33434. The range is 1–65535.

13. In the Size field, enter the size of the probe packets.

The default value is 0. The range is 0 to 39936.

14. From the Source menu, select the IP address or interface that must be used to send echo

request packets:

• None. The source address for the traceroute is the address of the default egress

interface.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual444

• IP Address. The source IP address that must be used for the traceroute. With this

selection, the IPv6 Address field displays and you must enter the IPv6 address that

must be used as the source.

• Interface. The interface that must be used for the traceroute. With this selection, the

Interface menu displays and you must select an interface as the source.

15. Click the Apply button.

A traceroute request is sent to the specified IP address or host name. The results are

displayed below the configurable data in the Results field.

Enable remote diagnostics

For enhanced security the remote diagnostic option is disabled by default. You can enable

option to access the switch remotely. When remote access is enabled, you or technical

support can perform remote diagnostics services.

To enable remote diagnostics:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of the

switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Maintenance > Troubleshooting > Remote Diagnostics.

The Remote Diagnostics page displays.

6. Select the Enable radio button.

7. Click the Apply button.

Your settings are saved.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual445

Configure memory dump settings and perform a full

memory dump

Note: Model GS418TPP supports a full memory dump. Models GS510TLP

and GS510TPP do not.

You can perform a full memory dump to retrieve the core dump for the purpose of

troubleshooting.

To configure the memory dump settings, send a test memory dump to a USB device,

and perform a full memory dump:

1. Connect your computer to the same network as the switch.

You can use a WiFi or wired connection to connect your computer to the network, or

connect directly to a switch that is off-network using an Ethernet cable.

2. Launch a web browser.

3. In the address field of your web browser, enter the IP address of the switch.

If you do not know the IP address of the switch, see Change the default IP address of

the switch on page 13.

The login window opens.

4. Enter the switch’s password in the Password field.

The default password is password.

The System Information page displays.

5. Select Maintenance > Troubleshooting > Full Memory Dump.

6. From the Protocol menu, select the protocol that must be used to save the core dump file:

• None. Disable the core dump. This is the default setting.

• USB. Sets the USB protocol.

7. In the File Path field, enter the path where the core dump file must be saved on the USB

device.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual446

The form of the full file path is /mnt/usb-storage/<dir>. The file path must consist of

-, _, / and alphanumeric characters. Up to 64 characters can be used. The default is /.

8. In the File Name field, specify the core dump file name. Up to 15 characters can be used.

The file name must consists of -, _, and alphanumeric characters. The default is core. The

form of the file name is as follows:

<file-name-prefix>_<Host_Name>.bin (timestamp disabled) or

<file-name-prefix>_<MAC_Address>_<Time_Stamp>.bin (host name disabled)

9. To append a host name to the core dump file name, select the Hostname check box.

If you do not select the Hostname check box, the system MAC address is included in the

file name. By default, the check box is not enabled.

10. Select the Time-stamp check box to append a timestamp to the core dump file name.

This check box is selected by default.

11. To let the switch dump the switch chip register in the case of an exception, select the Switch

When this option is enabled, all switch memories and switch registers are dumped to a

file with a prefix of reg. This option is disabled by default.

12. To test if a core dump can be written to the USB device (available only if you specified USB

as the protocol), do the following:

a. Select the Write Core Test check box.

CAUTION:

Make sure that the Write Core check box is cleared when you click the

Apply button. Otherwise, the switch reboots.

b. Click the Apply button.

A pop-up window opens and displays the test results. You can verify if the configured

settings are correct and if the USB device is accessible. The core dump file name that

you entered in the File Name field is used as the destination.

13. To write a core dump to the USB device (available only if you specified USB as the

protocol), do the following:

a. Select the Write Core check box.

CAUTION:

The switch reboots after you click the Apply button.

b. Click the Apply button.

The core dump is written to the USB device and the switch reboots.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Maintain or Troubleshoot the Switch User Manual447

14. To save the configuration settings, select the Save Current Settings check box.

By default, this check box is selected. You can clear the check box only if you first select

the Write Core check box.

CAUTION:

Make sure that the Write Core check box is cleared when you click the

Apply button. Otherwise, the switch reboots.

15. Click the Apply button.

Your settings are saved.

448

AConfiguration Examples

The appendix covers the following topics:

•Virtual Local Area Networks (VLANs)

•Access control lists (ACLs)

•Differentiated Services (DiffServ)

•802.1X access control

•Multiple Spanning Tree Protocol

•VLAN routing interfaces

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configuration Examples User Manual449

Virtual Local Area Networks (VLANs)

A local area network (LAN) can generally be defined as a broadcast domain. Hubs, bridges,

or switches in the same physical segment or segments connect all end node devices. End

nodes can communicate with each other without the need for a router . Routers connect LANs

together, routing the traffic to the appropriate port.

A virtual LAN (VLAN) is a local area network with a definition that maps workstations on

some basis other than geographic location (for example, by department, type of user, or

primary application). To enable traffic to flow between VLANs, traffic must go through a

router, just as if the VLANs were on two separate LANs.

A VLAN is a group of computers, servers, and other network resources that behave as if they

were connected to a single network segment—even though they might not be. For example,

all marketing personnel might be spread throughout a building. Yet if they are all assigned to

a single VLAN, they can share resources and bandwidth as if they were connected to the

same segment. The resources of other departments can be invisible to the marketing VLAN

members, accessible to all, or accessible only to specified individuals, depending on how the

IT manager set up the VLANs.

VLANs present a number of advantages:

•It is easy to do network segmentation. Users who communicate most frequently with

each other can be grouped into common VLANs, regardless of physical location. Each

group’s traffic is contained largely within the VLAN, reducing extraneous traffic and

improving the efficiency of the whole network.

•They are easy to manage. The addition of nodes, as well as moves and other changes,

can be dealt with quickly and conveniently from a management interface rather than from

the wiring closet.

•They provide increased performance. VLANs free up bandwidth by limiting node-to-node

and broadcast traffic throughout the network.

•They ensure enhanced network security. VLANs create virtual boundaries that can be

crossed only through a router. So standard, router-based security measures can be used

to restrict access to each VLAN.

Packets received by the switch are treated in the following way:

•When an untagged packet enters a port, it is automatically tagged with the port’s default

VLAN ID tag number. Each port supports a default VLAN ID setting that is user

configurable (the default setting is 1). The default VLAN ID setting for each port can be

changed on the Port PVID Configuration page. See Configure the port PVID settings on

page 145.

•When a tagged packet enters a port, the tag for that packet is unaffected by the default

VLAN ID setting. The packet proceeds to the VLAN specified by its VLAN ID tag number.

•If the port through which the packet entered is not a member of the VLAN as specified by

the VLAN ID tag, the packet is dropped.

•If the port is a member of the VLAN specified by the packet’s VLAN ID, the packet can be

sent to other ports with the same VLAN ID.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configuration Examples User Manual450

•Packets leaving the switch are either tagged or untagged, depending on the setting for

that port’s VLAN membership properties. A U for a given port means that packets leaving

the switch from that port are untagged. Inversely, a T for a given port means that packets

leaving the switch from that port are tagged with the VLAN ID that is associated with the

port.

The example given in this section comprises numerous steps to illustrate a wide range of

configurations to help provide an understanding of tagged VLANs.

VLAN configuration examples

This example demonstrates several scenarios of VLAN use and describes how the switch

handles tagged and untagged traffic.

In this example, you create two new VLANs, change the port membership for default VLAN 1,

and assign port members to the two new VLANs:

1. On the Basic VLAN Configuration page (see Configure VLANs on page 139), create the

following VLANs:

•A VLAN with VLAN ID 10.

•A VLAN with VLAN ID 20.

2. On the VLAN Membership page (see Configure VLAN membership on page 142) specify

the VLAN membership as follows:

•For the default VLAN with VLAN ID 1, specify the following members: port 7 (U) and

port 8 (U).

•For the VLAN with VLAN ID 10, specify the following members: port 1 (U), port 2 (U),

and port 3 (T).

•For the VLAN with VLAN ID 20, specify the following members: port 4 (U), port 5 (T),

and port 6 (U).

3. On the Port PVID Configuration page (see Configure the port PVID settings on

page 145), specify the PVID for ports g1 and g4 so that packets entering these ports are

tagged with the port VLAN ID:

•Port g1: PVID 10

•Port g4: PVID 20

4. With the VLAN configuration that you set up, the following situations produce results as

described:

•If an untagged packet enters port 1, the switch tags it with VLAN ID 10. The packet

can access port 2 and port 3. The outgoing packet is stripped of its tag to leave port 2

as an untagged packet. For port 3, the outgoing packet leaves as a tagged packet

with VLAN ID 10.

•If a tagged packet with VLAN ID 10 enters port 3, the packet can access port 1 and

port 2. If the packet leaves port 1 or port 2, it is stripped of its tag to leave the switch

as an untagged packet.

•If an untagged packet enters port 4, the switch tags it with VLAN ID 20. The packet

can access port 5 and port 6. The outgoing packet is stripped of its tag to become an

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configuration Examples User Manual451

untagged packet as it leaves port 6. For port 5, the outgoing packet leaves as a

tagged packet with VLAN ID 20.

Access control lists (ACLs)

ACLs ensure that only authorized users can access specific resources while blocking off any

unwarranted attempts to reach network resources.

ACLs are used to provide traffic flow control, restrict contents of routing updates, decide

which types of traffic are forwarded or blocked, and provide security for the network. ACLs

are normally used in firewall routers that are positioned between the internal network and an

external network, such as the Internet. They can also be used on a router positioned between

two parts of the network to control the traffic entering or exiting a specific part of the internal

network. The added packet processing required by the ACL feature does not affect switch

performance. That is, ACL processing occurs at wire speed.

Access lists are sequential collections of permit and deny conditions. This collection of

conditions, known as the filtering criteria, is applied to each packet that is processed by the

switch or the router. The forwarding or dropping of a packet is based on whether or not the

packet matches the specified criteria.

Traffic filtering requires the following two basic steps:

1. Create an access list definition.

The access list definition includes rules that specify whether traffic matching the criteria is

forwarded normally or discarded. Additionally, you can assign traffic that matches the

criteria to a particular queue or redirect the traffic to a particular port. A default deny all

rule is the last rule of every list.

2. Apply the access list to an interface in the inbound direction.

The switch allow ACLs to be bound to physical ports and LAGs. The switch software

supports MAC ACLs and IP ACLs.

MAC ACL example configuration

The following example shows how to create a MAC-based ACL that permits Ethernet traffic

from the Sales department on specified ports and denies all other traffic on those ports.

1. On the MAC ACL page, create an ACL with the name Sales_ACL for the Sales

department of your network (see Configure a MAC ACL on page 352).

By default, this ACL is bound on the inbound direction, which means that the switch

examines traffic as it enters the port.

2. On the MAC Rules page, create a rule for the Sales_ACL with the following settings:

•Sequence Number. 1

• Action. Permit

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configuration Examples User Manual452

• Assign Queue ID. 0

• Match Every. False

• CoS. 0

• Destination MAC. 01:02:1A:BC:DE:EF

• Destination MAC Mask. 00:00:00:00:FF:FF

• EtherType. User Value.

•Source MAC. 02:02:1A:BC:DE:EF

• Source MAC Mask. 00:00:00:00:FF:FF

• VLAN ID. 2

For more information about MAC ACL rules, see Configure MAC ACL rules on

page 355.

3. On the MAC Binding Configuration page, assign the Sales_ACL to the interface Gigabit

ports 6, 7, and 8, and then click the Apply button. (See Configure MAC bindings on

page 359.)

You can assign an optional sequence number to indicate the order of this access list

relative to other access lists if any are already assigned to this interface and direction.

4. The MAC Binding Table displays the interface and MAC ACL binding information. (See

View or delete MAC ACL bindings in the MAC binding table on page 360.)

The ACL named Sales_ACL looks for Ethernet frames with destination and source MAC

addresses and MAC masks defined in the rule. Also, the frame must be tagged with VLAN ID

2, which is the Sales department VLAN. The CoS value of the frame must be 0, which is the

default value for Ethernet frames. Frames that match this criteria are permitted on interfaces

6, 7, and 8 and are assigned to the hardware egress queue 0, which is the default queue. All

other traffic is explicitly denied on these interfaces. To allow additional traffic to enter these

ports, you must add a new Permit rule with the desired match criteria and bind the rule to

interfaces 6, 7, and 8.

Basic IP ACL example configuration

The following example shows how to create an IP-based ACL that prevents any IP traffic

from the Finance department from being allowed on the ports that are associated with other

departments. Traffic from the Finance department is identified by each packet’s network IP

address.

1. On the IP ACL page, create a new IP ACL with an IP ACL ID of 1. (See Configure a

basic or extended IPv4 ACL on page 361.)

2. On the IP Rules page, create a rule for IP ACL 1 with the following settings:

•Sequence Number. 1

• Action. Deny

• Assign Queue ID. 0 (optional: 0 is the default value)

• Match Every. False

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configuration Examples User Manual453

• Source IP Address. 192.168.187.0

• Source IP Mask. 255.255.0

For additional information about IP ACL rules, see Configure rules for a basic IPv4 ACL

on page 364.

3. Click the Add button.

4. On the IP Rules page, create a second rule for IP ACL 1 with the following settings:

•Sequence Number. 2

• Action. Permit

• Match Every. True

5. Click the Add button.

6. On the IP Binding Configuration page, assign ACL ID 1 to the interface Gigabit ports 2, 3,

and 4, and assign a sequence number of 1. (See Configure IP ACL interface bindings on

page 385.)

By default, this IP ACL is bound on the inbound direction, so it examines traffic as it

enters the switch.

7. Click the Apply button.

8. Use the IP Binding Table page to view the interfaces and IP ACL binding information. (See

View or delete IP ACL bindings in the IP ACL binding table on page 387)

The IP ACL in this example matches all packets with the source IP address and subnet mask

of the Finance department’s network and deny it on the Ethernet interfaces 2, 3, and 4 of the

switch. The second rule permits all non-Finance traffic on the ports. The second rule is

required because an explicit deny all rule exists as the lowest priority rule.

Differentiated Services (DiffServ)

Standard IP-based networks are designed to provide best effort data delivery service. Best

effort service implies that the network delivers the data in a timely fashion, although there is

no guarantee that it does. During times of congestion, packets might be delayed, sent

sporadically, or dropped. For typical Internet applications, such as email and file transfer, a

slight degradation in service is acceptable and in many cases unnoticeable. However, any

degradation of service can negatively affect applications with strict timing requirements, such

as voice or multimedia.

Quality of Service (QoS) can provide consistent, predictable data delivery by distinguishing

between packets with strict timing requirements from those that are more tolerant of delay.

Packets with strict timing requirements are given special treatment in a QoS-capable

network. With this in mind, all elements of the network must be QoS capable. If one node

cannot meet the necessary timing requirements, this creates a deficiency in the network path

and the performance of the entire packet flow is compromised.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configuration Examples User Manual454

Two basic types of QoS are supported:

• Integrated Services. Network resources are apportioned based on request and are

reserved (resource reservation) according to network management policy (RSVP, for

example).

• Differentiated Services. Network resources are apportioned based on traffic

classification and priority, giving preferential treatment to data with strict timing

requirements.

The switch supports DiffServ.

The DiffServ feature contains a number of conceptual QoS building blocks that you can use

to construct a differentiated service network. Use these same blocks in dif ferent ways to build

other types of QoS architectures.

You must configure three key QoS building blocks for DiffServ:

•Class

•Policy

•Service (the assignment of a policy to a directional interface)

Class

You can classify incoming packets at Layers 2, 3, and 4 by inspecting the following

information for a packet:

•Source/destination MAC address

•EtherType

•Class of Service (802.1p priority) value (first/only VLAN tag)

•VLAN ID range (first/only VLAN tag)

•Secondary 802.1p priority value (second/inner VLAN tag)

•Secondary VLAN ID range (second/inner VLAN tag)

•IP Service Type octet (also known as: ToS bits, Precedence value, DSCP value)

•Layer 4 protocol (TCP, UDP and so on)

•Layer 4 source/destination ports

•Source/destination IP address

From a DiffServ point of view, two types of classes exist:

•DiffServ traffic classes

•DiffServ service levels/forwarding classes

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configuration Examples User Manual455

DiffServ traffic classes

With DiffServ, you define which traffic classes to track on an ingress interface. You can define

simple BA classifiers (DSCP) and a wide variety of multifield (MF) classifiers:

•Layer 2; Layers 3, 4 (IP only)

•Protocol-based

•Address-based

You can combine these classifiers with logical AND or OR operations to build complex

MF-classifiers (by specifying a class type of all or any, respectively). That is, within a single

class, multiple match criteria are grouped together as an AND expression or a sequential OR

expression, depending on the defined class type. Only classes of the same type can be

nested; class nesting does not allow for the negation (exclude option) of the referenced

class.

To configure DiffServ, you must define service levels, namely the forwarding classes/PHBs

identified by a given DSCP value, on the egress interface. You define these service levels by

configuring BA classes for each.

Creating policies

Use DiffServ policies to associate a collection of classes that you configure with one or more

QoS policy statements. The result of this association is referred to as a policy.

From a DiffServ perspective, two types of policies exist:

• T raffic Conditioning Policy. A policy applied to a DiffServ traffic class

• Service Provisioning Policy. A policy applied to a DiffServ service level

You must manually configure the various statements and rules used in the traffic conditioning

and service provisioning policies to achieve the desired Traffic Conditioning Specification

(TCS) and the Service Level Specification (SLS) operation, respectively.

Traffic conditioning policy

Traffic conditioning pertains to actions performed on incoming traffic. Several distinct QoS

actions are associated with traffic conditioning:

• Dropping. Drop a packet upon arrival. This is useful for emulating access control list

operation using DiffServ, especially when DiffServ and ACL cannot coexist on the same

interface.

• Marking IP DSCP or IP Precedence. Marking/re-marking the DiffServ code point in a

packet with the DSCP value representing the service level associated with a particular

DiffServ traffic class. Alternatively, the IP precedence value of the packet can be

marked/re-marked.

• Marking CoS (802.1p). Sets the 3-bit priority field in the first/only 802.1p header to a

specified value when packets are transmitted for the traffic class. An 802.1p header is

inserted if it does not already exist. This is useful for assigning a Layer 2 priority level

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configuration Examples User Manual456

based on a DiffServ forwarding class (such as the DSCP or IP precedence value)

definition to convey some QoS characteristics to downstream switches that do not

routinely look at the DSCP value in the IP header.

• Policing. A method of constraining incoming traffic associated with a particular class so

that it conforms to the terms of the TCS. Special treatment can be applied to out-of-profile

packets that are either in excess of the conformance specification or are nonconformant.

The DiffServ feature supports the following types of traffic policing treatments (actions):

• drop. The packet is dropped.

•mark cos. The 802.1p user priority bits are (re)marked and forwarded.

•mark dscp. The packet DSCP is (re)marked and forwarded.

•mark prec. The packet IP Precedence is (re)marked and forwarded.

•send. The packet is forwarded without DiffServ modification.

Color Mode Awareness. Policing in the DiffServ feature uses either color blind or color

aware mode. Color blind mode ignores the coloration (marking) of the incoming packet.

Color aware mode takes into consideration the current packet marking when the switch

determines the policing outcome. An auxiliary traffic class is used in conjunction with the

policing definition to specify a value for one of the 802.1p, secondary 802.1p, IP DSCP, or

IP precedence fields designating the incoming color value to be used as the conforming

color. You can also specify the color of traffic that exceeds the threshold.

• Counting. Updating octet and packet statistics to keep track of data handling along traffic

paths within DiffServ. In this DiffServ feature, counters are not explicitly configured by the

user, but are designed into the system based on the DiffServ policy being created. For

more information, see Monitor the switch and the ports on page 392.

• Assigning QoS Queue. Directs a traffic stream to the specified QoS queue. This allows a

traffic classifier to specify which one of the supported hardware queues are used for

handling packets belonging to the class.

• Redirecting. Forces a classified traffic stream to a specified egress port (physical or

LAG). This can occur in addition to any marking or policing action. It can also be specified

along with a QoS queue assignment.

DiffServ example configuration

To create a DiffServ class and policy and attach them to a switch interface, follow these

steps:

1. On the QoS Class Configuration page, create a new class with the following settings:

• Class Name. Class1

• Class Type. All

For more information about this page, see Configure a DiffServ class on page 267.

2. Click the Class1 hyperlink to view the DiffServ Class Configuration page for this class.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configuration Examples User Manual457

3. Configure the following settings for Class1:

• Protocol Type. UDP

• Source IP Address. 192.12.1.0.

• Source Mask. 255.255.255.0.

• Source L4 Port. Other, and enter 4567 as the source port value.

•Destination IP Address. 192.12.2.0.

• Destination Mask. 255.255.255.0.

• Destination L4 Port. Other, and enter 4568 as the destination port value.

For more information about this page, see Configure a DiffServ class on page 267.

4. Click the Apply button.

5. On the Policy Configuration page, create a new policy with the following settings:

• Policy Selector. Policy1

• Member Class. Class1

For more information about this page, see Configure a DiffServ policy on page 278.

6. Click the Add button.

The policy is added.

7. Click the Policy1 hyperlink to view the Policy Class Configuration page for this policy.

8. Configure the Policy attributes as follows:

•Assign Queue. 3

• Policy Attribute. Simple Policy

• Color Mode. Color Blind

• Committed Rate. 1000000 Kbps

• Committed Burst Size. 128 KB

• Confirm Action. Send

• Violate Action. Drop

For more information about this page, see Configure a DiffServ policy on page 278.

9. On the Service Configuration page, select the check box next to interfaces g7 and g8 to

attach the policy to these interfaces, and then click the Apply button. (See Configure the

DiffServ service interface on page 283.)

All UDP packet flows destined to the 192.12.2.0 network with an IP source address from the

192.12.1.0 network that include a Layer 4 Source port of 4567 and Destination port of 4568

from this switch on ports 7 and 8 are assigned to hardware queue 3.

On this network, traffic from streaming applications uses UDP port 4567 as the source and

4568 as the destination. This real-time traffic is time sensitive, so it is assigned to a

high-priority hardware queue. By default, data traffic uses hardware queue 0, which is

designated as a best-effort queue.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configuration Examples User Manual458

Also the confirmed action on this flow is to send the packets with a committed rate of

1000000 Kbps and burst size of 128 KB. Packets that violate the committed rate and burst

size are dropped.

802.1X access control

Local area networks (LANs) are often deployed in environments that permit unauthorized

devices to be physically attached to the LAN infrastructure, or permit unauthorized users to

attempt to access the LAN through equipment already attached. In such environments you

might want to restrict access to the services offered by the LAN to those users and devices

that are permitted to use those services.

Port-based network access control makes use of the physical characteristics of LAN

infrastructures to provide a means of authenticating and authorizing devices attached to a

LAN port with point-to-point connection characteristics. If the authentication and authorization

process fails, access control prevents access to that port. In this context, a port is a single

point of attachment to the LAN, such as a port of a MAC bridge and an association between

stations or access points in IEEE 802.11 wireless LANs.

The IEEE 802.11 standard describes an architectural framework within which authentication

and consequent actions take place. It also establishes the requirements for a protocol

between the authenticator (the system that passes an authentication request to the

authentication server) and the supplicant (the system that requests authentication), as well

as between the authenticator and the authentication server.

The switch supports a guest VLAN, which allows unauthenticated users limited access to the

network resources.

Note: You can use QoS features to provide rate limiting on the guest VLAN

to limit the network resources that the guest VLAN provides.

Another 802.1X feature is the ability to configure a port to enable or disable EAPoL packet

forwarding support. You can disable or enable the forwarding of EAPoL when 802.1X is

disabled on the device.

The ports of an 802.1X authenticator switch provide the means by which it can offer services

to other systems reachable through the LAN. Port-based network access control allows the

operation of a switch’s ports to be controlled to ensure that access to its services is permitted

only by systems that are authorized to do so.

Port access control provides a means of preventing unauthorized access by supplicants to

the services offered by a system. Control over the access to a switch and the LAN to which it

is connected can be desirable when you restrict access to publicly accessible bridge ports or

to restrict access to departmental LANs.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configuration Examples User Manual459

Access control is achieved by enforcing authentication of supplicants that are attached to an

authenticator's controlled ports. The result of the authentication process determines whether

the supplicant is authorized to access services on that controlled port.

A port access entity (PAE) is able to adopt one of two distinct roles within an access control

interaction:

1. Authenticator. A port that enforces authentication before allowing access to services

available through that port.

2. Supplicant. A port that attempts to access services offered by the authenticator.

Additionally, there exists a third role:

3. Authentication server. Performs the authentication function necessary to check the

credentials of the supplicant on behalf of the authenticator.

All three roles are required for you to complete an authentication exchange.

The switch supports the authenticator role only, in which the PAE is responsible for

communicating with the supplicant. The authenticator PAE is also responsible for submitting

the information received from the supplicant to the authentication server for the credentials to

be checked, which determines the authorization state of the port. The authenticator PAE

controls the authorized/unauthorized state of the controlled port depending on the outcome

of the RADIUS-based authentication process.

Figure 1. 802.1X authentication roles

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configuration Examples User Manual460

802.1X example configuration

This example shows how to configure the switch so that 802.1X-based authentication is

required on the ports in a corporate conference room (1/0/5–1/0/8). These ports are available

to visitors and must be authenticated before access is granted to the network. The

authentication is handled by an external RADIUS server. When the visitor is successfully

authenticated, traffic is automatically assigned to the guest VLAN. This example assumes

that a VLAN was configured with a VLAN ID of 150 and VLAN name of Guest.

1. On the Port Authentication page, select ports 1/0/5, 1/0/6, 1/0/7, and 1/0/8.

2. From the Port Control menu, select Unauthorized.

The selection from the Port Control menu for all other ports on which authentication is

not needed must be Authorized. When the selection from the Port Control menu is

Authorized, the port is unconditionally put in a force-authorized state and does not

require any authentication. When the selection from the Port Control menu is Auto, the

authenticator PAE sets the controlled port mode.

3. In the Guest VLAN field for ports 1/0/5–1/0/8, enter 150 to assign these ports to the guest

VLAN.

You can configure additional settings to control access to the network through the ports.

See Configure a port security interface on page 337 for information about the settings.

4. Click the Apply button.

5. On the 802.1X Configuration page, set the port based authentication state and guest VLAN

mode to Enable, and then the Apply button. (See Configure the global port security

mode on page 336.)

This example uses the default values for the port authentication settings, but you can

configure several additional settings. For example, the EAPOL Flood Mode field allows

you to enable the forwarding of EAPoL frames when 802.1X is disabled on the device.

6. On the RADIUS Server Configuration page, configure a RADIUS server with the following

settings:

• Server Address. 192.168.10.23

• Secret Configured. Yes

• Secret. secret123

• Active. Primary

For more information, see Manage the RADIUS settings on page 290.

7. Click the Add button.

8. On the Authentication List page, configure the default list to use RADIUS as the first

authentication method. (See Configure authentication lists on page 302.)

This example enables 802.1X-based port security on the switch and prompts the hosts

connected on ports g5-g8 for an 802.1X-based authentication. The switch passes the

authentication information to the configured RADIUS server.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configuration Examples User Manual461

Multiple Spanning Tree Protocol

Spanning Tree Protocol (STP) runs on bridged networks to help eliminate loops. If a bridge

loop occurs, the network can become flooded with traffic. IEEE 802.1s Multiple Spanning

Tree Protocol (MSTP) supports multiple instances of spanning tree to efficiently channel

VLAN traffic over different interfaces. Each instance of the spanning tree behaves in the

manner specified in IEEE 802.1w, Rapid Spanning Tree, with slight modifications in the

working but not the end effect (chief among the effects is the rapid transitioning of the port to

the forwarding state).

The difference between the RSTP and the traditional STP (IEEE 802.1D) is the ability to

configure and recognize full-duplex connectivity and ports that are connected to end stations,

resulting in rapid transitioning of the port to the Forwarding state and the suppression of

Topology Change Notification. These features are represented by the pointtopoint and

edgeport parameters. MSTP is compatible to both RSTP and STP. It behaves in a way that is

appropriate for STP and RSTP bridges.

An MSTP bridge can be configured to behave entirely as a RSTP bridge or an STP bridge.

So, an IEEE 802.1s bridge inherently also supports IEEE 802.1w and IEEE 802.1D.

The MSTP algorithm and protocol provide simple and full connectivity for frames assigned to

any given VLAN throughout a bridged LAN comprising arbitrarily interconnected networking

devices, each operating MSTP, STP, or RSTP. MSTP allows frames assigned to different

VLANs to follow separate paths, each based on an independent Multiple Spanning Tree

Instance (MSTI), within Multiple Spanning Tree (MST) regions composed of LANs and or

MSTP bridges. These regions and the other bridges and LANs are connected into a single

Common Spanning Tree (CST). (IEEE DRAFT P802.1s/D13)

MSTP connects all bridges and LANs with a single Common and Internal Spanning Tree

(CIST). The CIST supports the automatic determination of each MST region, choosing its

maximum possible extent. The connectivity calculated for the CIST provides the CST for

interconnecting these regions, and an Internal Spanning Tree (IST) within each region.

MSTP ensures that frames with a given VLAN ID are assigned to one and only one of the

MSTIs or the IST within the region, that the assignment is consistent among all the

networking devices in the region, and that the stable connectivity of each MSTI and IST at

the boundary of the region matches that of the CST. The stable active topology of the bridged

LAN with respect to frames consistently classified as belonging to any given VLAN thus

simply and fully connects all LANs and networking devices throughout the network, though

frames belonging to different VLANs can take different paths within any region, per IEEE

DRAFT P802.1s/D13.

All bridges, whether they use STP, RSTP, or MSTP, send information in configuration

messages through Bridge Protocol Data Units (BPDUs) to assign port roles that determine

each port’s participation in a fully and simply connected active topology based on one or

more spanning trees. The information communicated is known as the spanning tree priority

vector. The BPDU structure for each of these dif ferent protocols is dif ferent. An MSTP bridge

transmits the appropriate BPDU depending on the received type of BPDU from a particular

port.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configuration Examples User Manual462

An MST region comprises of one or more MSTP bridges with the same MST configuration

identifier, using the same MSTIs, and without any bridges attached that cannot receive and

transmit MSTP BPDUs. The MST configuration identifier includes the following components:

1. Configuration identifier format selector

2. Configuration name

3. Configuration revision level

4. Configuration digest: 16-byte signature of type HMAC-MD5 created from the MST

Configuration Table (a VLAN ID to MSTID mapping)

Because multiple instances of spanning tree exist, an MSTP state is maintained on a

per-port, per-instance basis (or on a per-port, per-VLAN basis, as any VLAN can be in one

and only one MSTI or CIST). For example, port A can be forwarding for instance 1 while

discarding for instance 2. The port states changed since IEEE 802.1D specification.

To support multiple spanning trees, configure an MSTP bridge with an unambiguous

assignment of VLAN IDs (VIDs) to spanning trees. For such a configuration, ensure the

following:

1. The allocation of VIDs to FIDs is unambiguous.

2. Each FID that is supported by the bridge is allocated to exactly one spanning tree instance.

The combination of VID to FID and then FID to MSTI allocation defines a mapping of VIDs to

spanning tree instances, represented by the MST Configuration Table.

With this allocation we ensure that every VLAN is assigned to one and only one MSTI. The

CIST is also an instance of spanning tree with an MSTID of 0.

VIDs might be not be allocated to an instance, but every VLAN must be allocated to one of

the other instances of spanning tree.

The portion of the active topology of the network that connects any two bridges in the same

MST region traverses only MST bridges and LANs in that region, and never bridges of any

kind outside the region. In other words, connectivity within the region is independent of

external connectivity.

MSTP example configuration

This example shows how to create an MSTP instance from the switch. The example network

includes three different switches that serve dif ferent locations in the network. In this example,

ports 1/0/1–1/0/5 are connected to host stations, so those links are not subject to network

loops. Ports 1/0/6–1/0/8 are connected across switches 1, 2, and 3.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configuration Examples User Manual463

Figure 2. MSTP example configuration

Perform the following procedures on each switch to configure MSTP:

1. On the VLAN Configuration page, create VLANs 300 and 500 (see Configure the VLAN

Settings on page 140).

2. On the VLAN Membership page, include ports 1/0/1–1/0/8 as tagged (T) or untagged (U)

members of VLAN 300 and VLAN 500 (see Configure the VLAN Settings on page 140).

3. On the STP Configuration page, enable the Spanning Tree State option (see Configure the

STP settings and view the STP status on page 164).

Use the default values for the rest of the STP configuration settings. By default, the STP

operation mode is MSTP and the configuration name is the switch MAC address.

4. On the CST Configuration page, set the bridge priority value for each of the three switches

to force Switch 1 to be the root bridge:

• Switch 1. 4096

• Switch 2. 12288

• Switch 3. 20480

Note: Bridge priority values are multiples of 4096.

If you do not specify a root bridge and all switches are assigned the same bridge priority

value, the switch with the lowest MAC address is elected as the root bridge (see

Configure the CST settings on page 166).

5. On the CST Port Configuration page, select ports 1/0/1–1/0/8 and select Enable from the

STP Status menu (see Configure the CST port settings on page 167).

6. Click the Apply button.

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configuration Examples User Manual464

7. Select ports 1/0/1–1/0/5 (edge ports), and select Enable from the Fast Link menu.

Since the edge ports are not at risk for network loops, ports with Fast Link enabled

transition directly to the forwarding state.

8. Click the Apply button.

You can use the CST Port Status page to view spanning tree information about each port.

9. On the MST Configuration page, create a MST instances with the following settings:

• MST ID. 1

• Priority. Use the default (32768)

• VLAN ID. 300

For more information, see View Rapid STP Information on page 171.

10. Click the Add button.

11. Create a second MST instance with the following settings

• MST ID. 2

• Priority. 49152

• VLAN ID. 500

12. Click the Add button.

In this example, assume that Switch 1 became the root bridge for the MST instance 1, and

Switch 2 became the root bridge for MST instance 2. Switch 3 supports hosts in the sales

department (ports 1/0/1, 1/0/2, and 1/0/3) and in the HR department (ports 1/0/4 and 1/0/5).

Switches 1 and 2 also include hosts in the sales and HR departments. The hosts connected

from Switch 2 use VLAN 500, MST instance 2 to communicate with the hosts on Switch 3

directly. Likewise, hosts of Switch 1 use VLAN 300, MST instance 1 to communicate with the

hosts on Switch 3 directly.

The hosts use different instances of MSTP to effectively use the links across the switch. The

same concept can be extended to other switches and more instances of MSTP.

VLAN routing interfaces

VLANs divide broadcast domains in a LAN environment. When hosts in one VLAN must

communicate with hosts in another VLAN, the traffic must be routed between them. This is

known as inter-VLAN routing. On the switch, it is accomplished by creating Layer 3 interfaces

(switch virtual interfaces [SVI]).

When a port is enabled for bridging (the default) rather than routing, all normal bridge

processing is performed for an inbound packet, which is then associated with a VLAN. Its

MAC destination address (MAC DA) and VLAN ID are used to search the MAC address

table. If routing is enabled for the VLAN, and the MAC DA of an inbound unicast packet is

that of the internal bridge-router interface, the packet is routed. An inbound multicast packet

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Configuration Examples User Manual465

is forwarded to all ports in the VLAN, plus the internal bridge-router interface, if it was

received on a routed VLAN.

Since a port can be configured to belong to more than one VLAN, VLAN routing might be

enabled for all of the VLANs on the port, or for a subset. VLAN routing can be used to allow

more than one physical port to reside on the same subnet. It could also be used when a

VLAN spans multiple physical networks, or when additional segmentation or security is

required. A port can be either a VLAN port or a router port, but not both. However, a VLAN

port can be part of a VLAN that is itself a router port.

Complete these steps to configure a switch to perform interVLAN routing:

1. Use the IP Configuration page to enable routing on the switch.

For more information about this step, see Configure the router settings on page 220.

2. Determine the IP addresses that you want to assign to the VLAN interface on the switch.

For the switch to be able to route between the VLANs, the VLAN interfaces must be

configured with an IP address. When the switch receives a packet destined for another

subnet/VLAN, the switch looks at the routing table to determine where to forward the

packet. The packet is then passed to the VLAN interface of the destination. It is then sent

to the port where the end device is attached.

3. Use the VLAN Routing Wizard page to create a routing VLAN, configure the IP address and

subnet mask, and add the member ports.

For more information about this step, see Create a routing interface with the VLAN Static

Routing Wizard on page 241.

In the following figure, VLAN 300 is created with IP address 10.1.2.1 and subnet mask

255.255.255.0. Port r1 is a member port. (For more information about this page, see

Manage a VLAN routing interface on page 243.)

466

BSpecifications and Default Settings

The appendix covers the following topics:

•Switch default settings

•General feature default settings

•System setup and maintenance settings

•Port characteristics

•Traffic control settings

•Quality of Service settings

•Security settings

•System management settings

•Settings for other features

•Hardware technical specifications

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Specifications and Default Settings User Manual467

Switch default settings

The following table describes the switch default settings.

Table 97. Switch default settings

Feature Default

IP address 192.168.0.239

Subnet mask 255.255.255.0

Default gateway 192.168.0.254

Protocol DHCP

Management VLAN ID 1

Minimum password length Eight characters

IPv6 management Mode None

SNTP client Enabled

Global logging Enabled

RAM logging Enabled (Severity level: debug and above)

Persistent (FLASH) logging Disabled

DNS Enabled (No servers configured)

SNMP T raps Enabled

Auto Save Enabled

RMON Enabled

TACACS Not configured

RADIUS Not configured

SSL Disabled

Denial of service protection Disabled

Dot1x authentication

(IEEE 802.1X) Disabled

MAC-based port security All ports are unlocked

Access control lists (ACL) None configured

Protected ports None

Private groups None

Head of line blocking prevention Disabled

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Specifications and Default Settings User Manual468

General feature default settings

The following table describes the general feature default settings.

Advertised port speed Maximum capacity

Broadcast storm control Enabled

MAC table address aging 300 seconds (dynamic addresses)

Default VLAN ID 1

Default VLAN name Default

GVRP Disabled

Voice VLAN Disabled

Guest VLAN Disabled

RADIUS-assigned VLANs Disabled

Multiple Spanning Tree Disabled

Link aggregation No link aggregation groups (LAGs) configured

LACP system priority 32768

Routing mode Disabled

DiffServ Enabled

IGMP snooping Disabled

IGMP snooping querier Disabled

Table 98. General feature default settings

Feature Name/Setting Default

DHCP L2 relay, global

Admin mode Disabled

DHCP L2 relay, VLAN

Admin mode Disabled

Circuit ID mode Disabled

DHCP L2 relay, interface

Admin mode Disabled

Table 97. Switch default settings (continued)

Feature Default

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Specifications and Default Settings User Manual469

82 option trust mode Disabled

Virtual LAN (IEEE 802.1Q)

Default VLANs 1 (Default),

4089 (Auto-Video)

Note: All ports are members of default VLAN

Note: No ports are member of the Auto-Video VLAN

PVID 1

Acceptable frame types Admit all

Ingress filtering Disabled

Port priority 0

Jumbo frames

Frame size 1500

Flow control

Admin mode Disabled

802.1X

Port-based authentication state Disabled

VLAN assignment mode Disabled

Dynamic VLAN creation mode Disabled

EAPOL flood mode Disabled

Port control Auto

Guest VLAN ID 0

Guest VLAN period 90

Unauthenticated VLAN ID 0

Periodic reauthentication Disabled

Reauthentication period 3600

Quiet period 60

Resending EAP 30

Max EAP requests 2

Supplicant time-out 30

Server time-out 30

Table 98. General feature default settings (continued)

Feature Name/Setting Default

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Specifications and Default Settings User Manual470

STP/RSTP/MSTP, global

Spanning tree state Enabled

STP operation mode IEEE 802.1s RSTP

Configuration name MAC address

Configuration revision level 0

Forwarding of BPDUs while STP is disabled Disabled

CST bridge priority 32768

CST bridge maximum age 20

CST bridge hello time 2

CST bridge forward delay 15

CST spanning tree maximum hops 20

MST default instance ID 0

MST instance 0 priority 32768

MST instance 0 VLAN IDs 1, 4089

STP/RSTP/MSTP, interface

CST STP status Enabled

CST auto edge Enabled

CST fast link Disabled

CST BDPU forwarding Disabled

CST path cost 0

CST priority 128

CST external path cost 0

GARP

Join timer 20 (centiseconds)

Leave timer 60 (centiseconds)

Leave all timer 1000 (centiseconds)

GVRP, global

GVRP mode Disabled

GVRP, interface

Table 98. General feature default settings (continued)

Feature Name/Setting Default

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Specifications and Default Settings User Manual471

Port GVRP mode Disabled

Link aggregation

Lag name ch<n>, where n is 1 to 8

Admin mode Enabled

Hash mode 3 Source MAC, Destination MAC, VLAN, EtherT ype,

and incoming port associated with the packet

STP mode Enabled

Link trap Enabled

LAG type Static

Local Link Discovery Protocol (LLDP), global

TLV advertised interval 30

Hold multiplier 4

Reinitializing delay 2

Transmit delay 5

Fast start duration 3

Local Link Discovery Protocol (LLDP), interface

Admin status Tx and Rx

Management IP address Auto advertise

Notification Disabled

Optional TLVs Enabled

DHCP snooping, global

Admin mode Disabled

MAC address validation Enabled

DHCP snooping, interface

Trust mode Disabled

Logging invalid packets Disabled

Rate limit N/A

Burst interval N/A

Persistent configuration

Store Local

Table 98. General feature default settings (continued)

Feature Name/Setting Default

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Specifications and Default Settings User Manual472

Write delay 300

IP routing

Admin mode Disabled

Time-to-live 64

Maximum next hops 1

ARP/ARP aging

Age time (seconds) 1200

Response time (seconds) 10

Retries 10

Cache size 512

Dynamic review Enabled

Router discovery protocol

Advertise mode Disabled

Advertise address 224.0.0.1

Maximum advertise interval 600

Minimum advertise interval 450

Advertise lifetime 1800

Preference level 0

Differentiated Services

Admin mode Enabled

Class of Service (CoS), global

Trust mode 802.1p

802.1p to queue mapping (802.1p -> queue) 0 -> 1

1 -> 0

2 -> 0

3 -> 1

4 -> 2

5 -> 2

6 -> 3

7 -> 3

Table 98. General feature default settings (continued)

Feature Name/Setting Default

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Specifications and Default Settings User Manual473

DSCP to queue mapping (DSCP -> queue) Class selector:

(CS 0) 000000 -> 1

(CS 1) 001000 -> 0

(CS 2) 010000 -> 0

(CS 3) 011000 -> 1

(CS 4) 100000 -> 2

(CS 5) 101000 -> 2

(CS 6) 110000 -> 3

(CS 7) 111000 -> 3

Assured forwarding:

(AF 11) 001010 -> 0

(AF 12) 001100 -> 0

(AF 13) 001110 -> 0

(AF 21) 010010 -> 0

(AF 22) 010100 -> 0

(AF 23) 010110 -> 0

(AF 31) 011010 -> 1

(AF 32) 011100 -> 1

(AF 33) 011110 -> 1

(AF 41) 100010 -> 1

(AF 42) 100100 -> 1

(AF 43) 100110 -> 1

Expedited forwarding:

(EF) 101110 -> 2

Other:

(1) 000001 -> 1

(2) 000010 -> 1

(3) 000011 -> 1

(4) 000100 -> 1

(5) 000101 -> 1

(6) 000110 -> 1

(7) 000111 -> 1

(9) 001001 -> 0

(11) 001011 -> 0

(13) 001101 -> 0

(15) 001111 -> 0

(17) 010001 -> 0

(19) 010011 -> 0

(21) 010101 -> 0

(23) 010111 -> 0

(25) 011001 -> 1

(27) 011011 -> 1

(29) 011101 -> 1

(31) 011111 -> 1

Table 98. General feature default settings (continued)

Feature Name/Setting Default

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Specifications and Default Settings User Manual474

DSCP to queue mapping (DSCP -> queue)

(continued)

(33) 100001 -> 2

(35) 100011 -> 2

(37) 100101 -> 2

(39) 100111 -> 2

(41) 101001 -> 2

(43) 101011 -> 2

(45) 101101 -> 2

(47) 101111 -> 2

(49) 110001 -> 3

(50) 110010 -> 3

(51) 110011 -> 3

(52) 110100 -> 3

(53) 110101 -> 3

(54) 110110 -> 3

(55) 110111 -> 3

(57) 111011 -> 3

(58) 111010 -> 3

(59) 111011 -> 3

(60) 111100 -> 3

(61) 111101 -> 3

(62) 111110 -> 3

(63) 111111 -> 3

Class of Service (CoS), interface

Trust mode 802.1p

Interface shaping rate 0

802.1p to queue mapping (802.1p –> queue) 0 -> 1

1 -> 0

2 -> 0

3 -> 1

4 -> 2

5 -> 2

6 -> 3

7 -> 3

Queue minimum band width 0

Queue scheduler type Weighted

Auto-VoIP, protocol-based

Admin mode Disabled

Prioritization type Traffic class

Auto-VoIP traffic class 7

Table 98. General feature default settings (continued)

Feature Name/Setting Default

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Specifications and Default Settings User Manual475

System setup and maintenance settings

The following table describes the system setup and maintenance settings.

Table 99. System setup and maintenance settings

Feature Sets Supported Default

Boot code update 1 N/A

DHCP/manual IP 1 DHCP enabled/192.168.0.239

System name configuration 1 NULL

Configuration save/restore 1 N/A

Firmware upgrade 1 N/A

Restore defaults 1 (web and front-panel button) N/A

Dual image support 1 Enabled

Factory reset 1 N/A

Port characteristics

The following table describes the port characteristics.

Auto-VoIP, OUI-based

Admin mode Disabled

Auto-VoIP VLAN None

OUI-based priority 7

L2 loop protection

Admin mode Disabled

Table 100. Port characteristics

Feature Sets Supported Default

Auto negotiating speed and

full/half duplex All ports Auto negotiation

Auto MDI/MDIX for cross over cables on all ports Enabled

Table 98. General feature default settings (continued)

Feature Name/Setting Default

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Specifications and Default Settings User Manual476

Traffic control settings

The following table describes the traffic control settings.

Table 101. Traffic control settings

Feature Sets Supported Default

Storm control All ports Disabled

Jumbo frame All ports Disabled

Maximum = 9216 bytes

Quality of Service settings

The following table describes the Quality of Service settings.

Table 102. Quality of Service settings

Feature Sets Supported Default

Number of queues 8 N/A

802.1p 1 Enabled

DSCP 1 Disabled

Egress rate limiting All ports Disabled

802.3x flow control/back pressure All ports Disabled

Port mirroring: TX, RX, both 1 Disabled

Port trunking (aggregation) 8 Preconfigured

802.1D spanning tree 1 Disabled

802.1w RSTP 1 Enabled

802.1s spanning tree 8 instances Disabled

Static 802.1Q tagging 256 VID = 1

The maximum number of member

ports is equal to the number of

ports on the switch.

Learning process Supports static and dynamic MAC

entries Dynamic learning is enabled by

default

Table 100. Port characteristics (continued)

Feature Sets Supported Default

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Specifications and Default Settings User Manual477

Security settings

The following table describes the security settings.

Table 103. Security settings

Feature Sets Supported Default

802.1X All ports Disabled

MAC ACL 100 (shared with IP and IPv6

ACLs) All MAC addresses allowed

IP ACL 100 (shared with MAC and IPv6

ACLs) All IP addresses allowed

IPv6 ACL 100 (shared with IP ACL and MAC

ACL) All IP addresses allowed

Password control access 1 Idle timeout = 5 mins.

Password = password

Management security 1 profile with 20 rules for

HTTP/HTTPS/SNMP access to

allow/deny an IP address/subnet

All IP addresses allowed

Port MAC lock down All ports Disabled

System management settings

The following table describes the system management settings.

Table 104. System management settings

Feature Sets Supported Default

Multi-session web connections 4 Enabled

SNMPv1/v2

SNMPv3

Max 5 community entries Enabled (read, read/write

communities)

Time control 1 (local or SNTP) Local time enabled

LLDP/LLDP-MED All ports Enabled

Logging 3 (memory/Flash/server) Memory log enabled

MIB support 1 Disabled

Smart Control Center N/A Enabled

Statistics N/A N/A

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Specifications and Default Settings User Manual478

Settings for other features

The following table describes the settings for other features.

Table 105. Settings for other features

Feature Sets Supported Default

IGMP snooping v1/v2/v3 All ports Disabled

Configurations upload/download 1 N/A

EAPoL flooding All ports Disabled

BPDU flooding All ports Disabled

Static multicast groups 8 Disabled

Filter multicast control 1 Disabled

Number of IPv4/IPv6 static routes 32 N/A

Number of routed VLANs 15 N/A

Max ARP entries 511 (479 dynamic, 32 static) N/A

Number of DHCP snooping

bindings 8K N/A

Number of DHCP static entries 1024 N/A

MLD Snooping N/A Disabled

Protocol and MAC-based VLAN N/A N/A

Dynamic ARP Inspection N/A Disabled

Multiple VLAN Registration (MVR) N/A Disabled

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Specifications and Default Settings User Manual479

Hardware technical specifications

The following table describes the hardware technical specifications.

Table 106. Hardware technical specifications

Feature Model GS418TPP Model GS510TLP Model GS510TPP

Network interfaces Eight

10/100/1000BASE-T RJ-45

PoE+ copper ports

Eight

10/100/1000BASE-T RJ-45

PoE+ copper ports

Sixteen

10/100/1000BASE-T RJ-45

PoE+ copper ports

Two 100/1000BASE-X

fiber SFP ports T wo 100/1000BASE-X fiber

SFP ports T wo 100/1000BASE-X fiber

SFP ports

USB ports One None None

Fans One fixed, internal None One fixed, internal

Power supply One fixed, internal One fixed, internal One fixed, internal

Switch PoE+ power

budget 240W 75W 190W

Maximum power

consumption With PoE: 282.3W

Without PoE: 17.8W

With PoE: 101W

Without PoE: 10.5W

With PoE: 225W

Without PoE: 12.5W

Dimensions

(W x D x H) 17.3 x 3.9 x 1.7 in.

(440 x 100 x 43 mm) 12.9 x 6.7 x 1.7 in.

(328 x 169 x 43 mm) 12.9 x 6.7 x 1.7 in.

(328 x 169 x 43 mm)

Weight 4.72 lb (2.14 kg) 3.84 lb (1.74 kg) 4.03 lb (1.83 kg)

Operating temperature 32º to 122ºF (0° to 50°C)

Operating humidity 90% maximum relative humidity, noncondensing

Maximum operating

altitude 10,000 ft (3,000 m)

Storage temperature –4° to 158°F (–20º to 70ºC)

Storage humidity 95% maximum relative humidity, noncondensing

Maximum storage

altitude 10,000 ft (3,000 m)

8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP

Specifications and Default Settings User Manual480

Electromagnetic

certifications and

compliance

CE: EN 55032:2012+AC:2013/CISPR 32:2012, EN 61000-3-2:2014,

Class A, EN 61000-3-3:2013, EN 55024:2010

VCCI: VCCI-CISPR 32:2016, Class A

RCM: AS/NZS CISPR 32:2013 Class A

CCC: GB4943.1-2011; YD/T993-1998; GB/T9254-2008 (Class A)

FCC: 47 CFR FCC Part 15, Class A, ANSI C63.4:2014

ISED: ICES-003:2016 Issue 6, Class A, ANSI C63.4:2014

BSMI: CNS 13438 Class A

Safety certifications CB report / certificate IEC 60950-1:2005 (ed.2) + A1:2009 + A2:2013

UL listed (UL 1950)/cUL IEC 950/EN 60950

CE LVD: EN 60950-1: 2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013

RCM (AS/NZS) 60950.1:2015

CCC (China Compulsory Certificate): GB4943.1-2011; YD/T993-1998;

GB/T9254-2008 (Class A)

BSMI: CNS 14336-1

Table 106. Hardware technical specifications (continued)

Feature Model GS418TPP Model GS510TLP Model GS510TPP

Table of Contents

NETGEAR GS510TPP User Manual

Related Manuals