Table of Contents
- IMPORTANT INFORMATION
- DEAR SHARP CUSTOMER
- SAFETY PRECAUTIONS
- TIPS AND SAFETY INSTRUCTIONS
- MOUNTING PRECAUTIONS
- Supplied Components
- Part Names
- Connecting Peripheral Equipment
- Connecting the Power Cord
- Binding Cables
- Preparing the Remote Control Unit
- Turning Power On/Off
- Basic Operation
- Remote Control Mode
- Menu Items
- Initialization (Reset)/Functional Restriction Setting (FUNCTION)
- Controlling the Monitor with a computer (RS-232C)
- Controlling the Monitor with a computer (LAN)
- Troubleshooting
- Specifications
- Mounting Precautions (For SHARP dealers and service engineers)
Sharp PN-V701 User Manual
Displayed below is the user manual for PN-V701 by Sharp which is a product in the Signage Displays category. This manual has pages.
Related Manuals
PN-V701
LCD MONITOR
OPERATION MANUAL
Information on the Disposal of this Equipment and its Batteries
IF YOU WISH TO DISPOSE OF THIS EQUIPMENT OR ITS BATTERIES, DO NOT USE THE ORDINARY WASTE BIN,
AND DO NOT PUT THEM INTO A FIREPLACE!
Used electrical and electronic equipment and batteries should always be collected and treated SEPARATELY in accordance
with local law.
Separate collection promotes an environment-friendly treatment, recycling of materials, and minimizing nal disposal of
waste. IMPROPER DISPOSAL can be harmful to human health and the environment due to certain substances! Take USED
EQUIPMENT to a local, usually municipal, collection facility, where available.
Remove USED BATTERIES from equipment, and take them to a battery collection facility; usually a place where new
batteries are sold.
If in doubt about disposal, contact your local authorities or dealer and ask for the correct method of disposal.
ONLY FOR USERS IN THE EUROPEAN UNION, AND SOME OTHER COUNTRIES; FOR INSTANCE NORWAY AND
SWITZERLAND: Your participation in separate collection is requested by law.
The symbol shown above appears on electrical and electronic equipment and batteries (or the packaging) to remind users
of this. If ‘Hg’ or ‘Pb’ appears below the symbol, this means that the battery contains traces of mercury (Hg) or lead (Pb),
respectively.
Users from PRIVATE HOUSEHOLDS are requested to use existing return facilities for used equipment and batteries.
Batteries are collected at points of sale. Return is free of charge.
If the equipment has been used for BUSINESS PURPOSES, please contact your SHARP dealer who will inform you about
take-back. You might be charged for the costs arising from take-back. Small equipment (and small quantities) might be taken
back by your local collection facility. For Spain: Please contact the established collection system or your local authority for
take-back of your used products.
3E
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning ash with arrowhead symbol, within
a triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufcient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
FOR CUSTOMERS IN U.K.
IMPORTANT
The wires in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW: Earth
BLUE: Neutral
BROWN: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the
terminals in your plug proceed as follows:
• The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth or coloured green or green-and-yellow.
• The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black.
• The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red.
Ensure that your equipment is connected correctly. If you are in any doubt consult a qualied electrician.
“WARNING: THIS APPARATUS MUST BE EARTHED.”
4
E
Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your
product, please read the Safety Precautions carefully before using this product.
SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly
handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can
result in electric shock and/or re. In order to prevent potential danger, please observe the following instructions when installing,
operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the
following precautions carefully before using the product.
1. Read instructions — All operating instructions must be read and understood before the product is operated.
2. Keep this manual in a safe place — These safety and operating instructions must be kept in a safe place for future
reference.
3. Observe warnings — All warnings on the product and in the instructions must be observed closely.
4. Follow instructions — All operating instructions must be followed.
5. Cleaning — Unplug the power cord from the power outlet before cleaning the product. Use a dry cloth to clean the product.
Do not use liquid cleaners or aerosol cleaners. Do not use dirty cloths. Doing so may damage the product.
6. Attachments — Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result
in accidents.
7. Water and moisture — Do not use the product near water. Do not install the product in a place where water may splash onto
it. Be careful of equipment which drains water such as an air-conditioner.
8. Ventilation — The vents and other openings in the cabinet are designed for ventilation.
Do not cover or block these vents and openings since insufcient ventilation can cause overheating and/or shorten the life
of the product. Do not place the product on a sofa, rug or other similar surface, since they can block ventilation openings.
Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
9. Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from
resting on them.
10. The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with
impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.
11. Overloading — Do not overload power outlets or extension cords. Overloading can cause re or electric shock.
12. Entering of objects and liquids — Never insert an object into the product through vents or openings. High voltage ows in
the product, and inserting an object can cause electric shock and/or short internal parts.
For the same reason, do not spill water or liquid on the product.
13. Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other
dangerous conditions. Request a qualied service person to perform servicing.
14. Repair — If any of the following conditions occurs, unplug the power cord from the power outlet, and request a qualied
service person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls
not described in the instructions can cause damage, which often requires extensive adjustment work by a qualied
technician.
e. When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product
needs servicing.
15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement
parts specied by the manufacturer, or those with the same characteristics and performance as the original parts. Use of
unauthorized parts can result in re, electric shock and/or other danger.
16. Safety checks — Upon completion of service or repair work, request the service technician to perform safety checks to
ensure that the product is in proper operating condition.
17. Wall mounting — When mounting the product on a wall, be sure to install the product according to the method
recommended by the manufacturer.
18. Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating
products (including ampliers).
DEAR SHARP CUSTOMER
5E
SAFETY PRECAUTIONS (Continued)
19. Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment,
dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below:
• Use the specied batteries only.
• Install the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the
compartment.
• Do not mix old and new batteries.
• Do not mix batteries of different types. Voltage specications of batteries of the same shape may vary.
• Replace an exhausted battery with a new one promptly.
• If you will not use the remote control for a long time, remove the batteries.
• If leaked battery uid gets on your skin or clothing, rinse immediately and thoroughly. If it gets into your eye, bathe your
eye well rather than rubbing and seek medical treatment immediately. Leaked battery uid that gets into your eye or your
clothing may cause a skin irritation or damage your eye.
20. Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury,
severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and
missile launch control in a weapon system.
21. Do not stay in contact with the parts of the product that become hot for long periods of time. Doing so may result in
low-temperature burns.
22. Do not modify this product.
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may
be required to take adequate measures.
An apparatus with CLASS I construction shall be connected to a MAIN socket outlet with a protective earthing connection.
To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: HDMI input terminal,
D-sub input terminal, RS-232C input/output terminals, DVI-D input terminal and DisplayPort input/output terminals.
If a monitor is not positioned in a sufciently stable location, it can be potentially hazardous due to falling. Many injuries,
particularly to children, can be avoided by taking simple precautions such as:
• Using xing devices like wall mount brackets recommended by the manufacturer.
• Only using furniture that can safely support the monitor.
• Ensuring the monitor is not overhanging the edge of the supporting furniture.
• Not placing the monitor on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the
monitor to a suitable support.
• Not standing the monitors on cloth or other materials placed between the monitor and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach the monitor or its controls.
• This equipment is not suitable for use in locations where children are likely to be present unsupervised.
Especially for child safety
- Don’t allow children to climb on or play with the monitor.
- Don’t place the monitor on furniture that can easily be used as steps, such as a chest of drawers.
- Remember that children can become excited while watching a program, especially on a “larger than life” monitor. Care
should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.
- Care should be taken to route all cords and cables connected to the monitor so that they cannot be pulled or grabbed by
curious children.
6
E
- The TFT color LCD panel used in this monitor is made with
the application of high precision technology. However, there
may be minute points on the screen where pixels never light
or are permanently lit. Also, if the screen is viewed from
an acute angle there may be uneven colors or brightness.
Please note that these are not malfunctions but common
phenomena of LCDs and will not affect the performance of
the monitor.
- Do not display a still picture for a long period, as this could
cause a residual image.
- Never rub or tap the monitor with hard objects.
- Please understand that SHARP CORPORATION bears no
responsibility for errors made during use by the customer or
a third party, nor for any other malfunctions or damage to this
product arising during use, except where indemnity liability is
recognized under law.
- This monitor and its accessories may be upgraded without
advance notice.
- Do not use the monitor where there is a lot of dust, where
humidity is high, or where the monitor may come into contact
with oil or steam. Do not use in an environment where
there are corrosive gases (sulfur dioxide, hydrogen sulde,
nitrogen dioxide, chlorine, ammonia, ozone, etc.). As this
could lead to re.
- Ensure that the monitor does not come into contact with
water or other uids. Ensure that no objects such as paper
clips or pins enter the monitor as this could lead to re or
electric shock.
- Do not place the monitor on top of unstable objects or in
unsafe places. Do not allow the monitor to receive strong
shocks or to strongly vibrate. Causing the monitor to fall or
topple over may damage it.
- Do not use the monitor near heating equipment or in places
where there is likelihood of high temperature, as this may
lead to generation of excessive heat and outbreak of re.
- Do not use the monitor in places where it may be exposed to
direct sunlight. Risk of cabinet deformation and failure if the
monitor is used in direct sunlight.
- If the monitor is installed in a location exposed to sunlight
such as next to a window, measures to reduce ultraviolet and
infrared radiation and temperature measures are required.
For details, consult your dealer.
- Please be sure to constantly remove dust and garbage that
has attached to the ventilation opening.
If dust collects in the ventilation opening, it may lead to
excessive heat, outbreak of re, or malfunction.
- As a standard, clean the inside of the monitor once every
year. If dust collects inside the monitor, it may lead to
excessive heat, outbreak of re, or malfunction. Please
request a cleaning of the inside of the monitor from an
authorized SHARP servicing dealer or service center.
- Images cannot be rotated on this monitor.
When using in portrait orientation, you will need to prepare
appropriately orientated content in advance.
- The power outlet shall be installed near the equipment and
shall be easily accessible.
The Power Cord
- Use only the power cord supplied with the monitor.
- Do not damage the power cord nor place heavy objects on
it, stretch it or over bend it. Also, do not add extension cords.
Damage to the cord may result in re or electric shock.
- Do not use the power cord with a power tap.
Adding an extension cord may lead to re as a result of
overheating.
- Do not remove or insert the power plug with wet hands.
Doing so could result in electric shock.
- Unplug the power cord if it is not used for a long time.
-
Do not attempt to repair the power cord if it is broken or
malfunctioning. Refer the servicing to the service representative.
Manual Scope
- Microsoft and Windows are either registered trademarks or
trademarks of Microsoft Corporation in the United States
and/or other countries.
- The terms HDMI and HDMI High-Denition Multimedia
Interface, and the HDMI Logo are trademarks or registered
trademarks of HDMI Licensing Administrator, Inc. in the
United States and other countries.
- DisplayPort is a registered trademark of Video Electronics
Standards Association.
- Adobe, Acrobat, and Acrobat Reader are either registered
trademarks or trademarks of Adobe Systems Incorporated in
the United States and/or other countries.
- RoomView, Crestron RoomView and Crestron Connected
are either trademarks or registered trademarks of Crestron
Electronics, Inc. in the United States and/or other countries.
- All other brand and product names are trademarks or
registered trademarks of their respective holders.
- Language of OSD menu used in this manual is English by
way of example.
- Illustrations in this manual may not exactly represent the
actual product or display.
- This manual assumes use in landscape orientation, except
where specically noted.
- This manual assumes that this product will be used with
the remote control unit buttons, except where specically
noted. Operation by using the buttons on the rear side of the
product will perform the same functions.
Remote control
unit buttons
Rear side buttons
* For operation with the remote control unit, the PN-ZR02
control kit (optional) is required.
LED Backlight
● The LED backlight in this product has a limited lifetime.
* If the screen gets dark or does not turn on, it may be
necessary to replace the LED backlight.
* This LED backlight is exclusive to this product and must
be replaced by an authorized SHARP servicing dealer
or service center. Please contact an authorized SHARP
servicing dealer or service center for assistance.
Fan
● The fan in this product has a limited lifetime.
● Please contact an authorized SHARP servicing dealer or
service center for assistance with fan replacement.
TIPS AND SAFETY INSTRUCTIONS
7E
MOUNTING PRECAUTIONS
• This product is for use indoors.
• A VESA-compliant mounting bracket is required.
• Since the monitor is heavy, consult your dealer before
installing, removing or moving the monitor.
• Mounting the monitor on the wall requires special expertise
and the work must be performed by an authorized SHARP
dealer. You should never attempt to perform any of this
work yourself. Our company will bear no responsibility
for accidents or injuries caused by improper mounting or
mishandling.
• Use the monitor with the surface perpendicular to a level
surface.
• This monitor should be used at an ambient temperature
between 32°F (0°C) and 104°F (40°C).
• Be careful of high temperatures in the surrounding area.
If it is difcult to provide sufcient space for any reason
such as the installation of the monitor inside a housing, or
if the ambient temperature may be outside of the range
of 32°F (0°C) to 104°F (40°C), install a fan or take other
measures to keep the ambient temperature within the
required range.
• Temperature condition may change when using the monitor
together with the optional equipments recommended by
SHARP. In such cases, please check the temperature
condition specied by the optional equipments.
• Do not block any ventilation openings. If the temperature
inside the monitor rises, this could lead to a malfunction.
• Do not place the monitor on a device which generates heat.
• Adhere to the following when installing the monitor in its
portrait orientation. Failing to adhere to the following may
cause malfunctions.
- To install in landscape orientation, rotate the monitor 90
degrees to the right.
- Set the PORTRAIT/LANDSCAPE INSTALL on the
MONITOR menu to PORTRAIT. (See page 30.)
- Be sure to clamp the power cord (supplied) onto the cable
clamp attachment using the supplied cable clamp. When
clamping the power cord, take care not to stress the
terminal of the power cord. Do not bend the power cord
excessively.
Power cord
(Supplied)
Cable clamp
Cable clamp attachment
• A video wall should be only be composed of identical
models. Do not use this monitor as part of a video wall that
includes another model.
8
E
Supplied Components
If any components are missing, please contact your dealer.
Liquid Crystal Display Monitor: 1
Cable clamp: 4
Cable clamp (insertion type): 2
Power cord
CD-ROM (Utility Disk for Windows): 1
Setup Manual: 1
Remote control sensor box mounting hole concealing sticker: 2
* The remote control unit is supplied with the PN-ZR02 control kit (optional).
* SHARP Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission.
* For environmental protection!
Do not dispose of batteries in household waste. Follow the disposal instructions for your area.
Contents
IMPORTANT INFORMATION ............................................3
DEAR SHARP CUSTOMER ..............................................4
SAFETY PRECAUTIONS ..................................................4
TIPS AND SAFETY INSTRUCTIONS ...............................6
MOUNTING PRECAUTIONS ............................................7
Supplied Components ..................................................... 8
Part Names .......................................................................9
Connecting Peripheral Equipment ............................... 11
Multiple monitor connection .......................................13
Connecting the Power Cord .........................................15
Binding Cables ............................................................... 16
Preparing the Remote Control Unit .............................. 17
Installing the batteries ................................................17
Remote control operation range .................................17
Turning Power On/Off .................................................... 18
Turning on the main power.........................................18
Turning power on/off ..................................................18
Disabling power on/off operations ..............................19
Basic Operation .............................................................20
Remote Control Mode ..................................................23
Menu Items .....................................................................24
Displaying the menu screen ....................................... 24
Menu item details .......................................................25
Adjustments for computer screen display ..................36
Initialization (Reset)/Functional Restriction Setting
(FUNCTION) ....................................................................37
Controlling the Monitor with a computer (RS-232C)
...38
Computer connection .................................................38
Communication conditions .........................................38
Communication procedure .........................................38
Setting of the GAMMA user data ................................ 41
RS-232C command table ........................................... 42
Controlling the Monitor with a computer (LAN) .......... 51
Settings to connect to a LAN ......................................51
Controlling with a computer ........................................53
[Advanced operation]
Command-based control ............................................ 60
Troubleshooting .............................................................61
Specications ...............................................................63
Mounting Precautions
(For SHARP dealers and service engineers) ............... 69
9E
nFront view
The rear buttons
if seen from the front
11 10 98765432
1
1. LCD panel
2. Power LED
3. POWER button
4. Cursor control ( ) button
5. Cursor control ( ) button
6. Cursor control ( ) button
7. Cursor control ( ) button
8. MENU button
9. INPUT button
10. RETURN button
11. ENTER button
Part Names
nRear view
14
12
12
30
17
23 24 25 26 27 28 29
12
12
13
15 16
23 4 5 6 7 89 10 11
13
18
19
20
21
22
12. Handles
13. Fan/Fan Cover
14. Vents
15. AC input terminal (See page 15.)
16. Main power switch (See page 18.)
17. DisplayPort output terminal (See page 11.)
18. HDMI1 input terminal (See page 11.)
19. HDMI2 input terminal (See page 11.)
20. DisplayPort input terminal (See page 11.)
21. DVI-D input terminal (See page 12.)
22. D-sub input terminal (See page 12.)
23. Audio input terminal (See page 12.)
24. Audio output terminal (See page 12.)
25. Optional terminal
This terminal is provided for possible future
(optional) function expansion. Offering of
this terminal is not a guarantee that future
expanded functionality will be provided.
26. RS-232C input terminal (See page 12.)
27. RS-232C output terminal (See page 12.)
28. LAN terminal (See page 12.)
29. Control kit terminal (See page 12.)
30. Expansion slot
This section is used to connect optional
hardware for function expansion. Offering this
attachment location is not a guarantee that
future compatible hardware attachments will
be released.
Caution
• Consult your SHARP dealer for attachment/detachment of
optional parts.
• Do not block the fan cover.
10
E
Part Names
1. Remote control sensor
2. Connection cable
3. Mounting bracket
n
Remote control sensor box
(Supplied with the PN-ZR02 (optional))
1
2
3
2
1
1. Signal transmitter
2. Operation buttons (See pages 20 and 21.)
n
Remote control unit
(Supplied with the PN-ZR02 (optional))
11 E
Connecting Peripheral Equipment
Caution
• Be sure to turn off the main power switch and disconnect
the plug from the power outlet before connecting/
disconnecting cables. Also, read the manual of the
equipment to be connected.
• Be careful not to confuse the input terminal with the output
terminal when connecting cables. Accidentally reversing
cables connected to the input and output terminals may
cause malfunctions and the other problems.
• Do not use any cable that has a damaged or deformed
terminal. Using such cables may cause malfunctions.
• Do not forcibly bend or apply force to cables. Doing so may
result in wire breakage or other damage.
TIPS
• Images may not be displayed properly depending on the
computer (video card) to be connected.
• Use the automatic screen adjustment when a computer
screen is displayed for the rst time using D-SUB[RGB] or
when the setting of the computer is changed. The screen
is adjusted automatically when SELF ADJUST in the
MONITOR menu is set to ON.
• If the audio output from the playback device is connected
directly to speakers or other devices, the video on the
monitor may appear delayed from the audio portion.
Audio should be played through this monitor by connecting
the playback device to the monitor’s audio input, and
connecting the monitor’s audio output to the speakers or
other devices.
• The audio input terminals used in each input mode are
factory-set as follows.
Input mode Audio input terminal
(Factory setting)
DVI-D Audio input terminal
DisplayPort DisplayPort input terminal
HDMI1 HDMI1 input terminal
HDMI2 HDMI2 input terminal
D-SUB[RGB],
D-SUB[COMPONENT] Audio input terminal
OPTION * Expansion slot
* When you have used the expansion slot to expand the
functions.
1. DisplayPort output terminal
• The video of the current input mode can be output to an
external device.
• Use a commercially available DisplayPort cable that
supports 4K.
• Outputting HDCP-encrypted video requires an external
device which supports HDCP.
• This terminal can be used to make a daisy chain
connection* by connecting these monitors to each other
through the DisplayPort input terminal of each monitor.
*: Up to 25 monitors.
Up to 4 monitors when the video signal is encrypted by
HDCP.
Up to 4 monitors when the rst monitor’s input mode is
D-SUB[COMPONENT].
Up to 2 monitors when the rst monitor’s input mode is
DisplayPort (MST).
TIPS
• The length of the signal cables or surrounding environment
may affect the image quality.
• The output screen may not be displayed properly. In this
case, turn off the power to all the monitors connected in a
daisy chain and then turn the power on again.
• When connecting monitors in a daisy chain set NO SIGNAL
AUTO INPUT SEL. to OFF.
• Video output is disabled in the following cases:
When the power is turned off.
When the monitor is in input signal waiting mode.
2. HDMI1 input terminal
3. HDMI2 input terminal
• Use a commercially available HDMI cable (conforming to
the HDMI standard).
• Select the audio input terminal to be used in HDMI1 or
HDMI2 of AUDIO SELECT on the SETUP menu.
When HDMI is selected, it is not necessary to connect an
audio cable to the audio input terminal.
4. DisplayPort input terminal
• Use a commercially available DisplayPort cable that
supports 4K.
• Select the audio input terminal to be used in DisplayPort
of AUDIO SELECT on the SETUP menu.
When DisplayPort is selected, it is not necessary to
connect an audio cable to the audio input terminal.
9 10 11 1287
1
3
2
4
5
6
12
E
Connecting Peripheral Equipment
5. DVI-D input terminal
• Use a commercially available signal cable (DVI-D 24 pin).
6. D-sub input terminal
• Set D-SUB of INPUT SELECT on the SETUP menu
according to the device to be connected.
7. Audio input terminal
• Use an audio cable without resistance.
• Set the audio input terminal to be used in each input
mode in AUDIO SELECT on the SETUP menu.
8. Audio output terminal
• The output sound varies depending on the input mode.
• The volume of the output sound can be xed by setting
AUDIO OUTPUT on the SETUP menu.
9. RS-232C input terminal
10. RS-232C output terminal
• You can control the monitor from a computer by
connecting a commercially available RS-232 straight
cable between these terminals and the computer.
11. LAN terminal
• You can control the monitor from a computer on a network
by connecting a commercially available LAN cable
between this terminal and a network.
12. Control kit terminal
• Connects the remote control sensor box of the PN-ZR02
control kit (optional). (See page 14.)
13 E
Connecting Peripheral Equipment
Multiple monitor connection
The monitors can be aligned and used as a large screen.
[Example]
Second monitor
Secondary
(Expansion unit)
ID No.: 2
Third monitor
Secondary
(Expansion unit)
ID No.: 3
First monitor
Primary
(Main unit)
ID No.: 1
Fourth monitor
Secondary
(Expansion unit)
ID No.: 4
Remote control sensor box
(Supplied with the PN-ZR02 (optional))
TIPS
• Connect the RS-232 cables in order, starting with the rst
monitor (primary monitor). If monitors are connected in a
different order they may not be operable.
• Always install the remote control sensor box on the primary
monitor.
nConnection with video cable
Up to 25 monitors* can be connected in a daisy chain.
*:
Up to 4 monitors when the video signal is encrypted by HDCP.
Up to 4 monitors when the rst monitor’s input mode is
D-SUB[COMPONENT].
Up to 2 monitors when the rst monitor’s input mode is
DisplayPort (MST).
To DisplayPort output terminal
First monitor Second monitor
DisplayPort
input
terminal
DisplayPort
input
terminal
DisplayPort cable that supports 4K
(commercially available)
shows the signal
flow
DisplayPort
output terminal
nConnection with RS-232 cable
If you connect the monitor in a daisy chain using RS-232
cables, settings are copied from the primary (main unit) to the
secondary (expansion unit) and operation from the primary
can perform operation for all monitors.
Setting each ID No. in the monitor is required.
1. Connect the monitors in order.
Connect the RS-232C output terminal of the rst monitor
(primary) and the RS-232C input terminal of the second
monitor (secondary) together using RS-232 cable (straight).
Connect in the same way to the third and subsequent
monitors.
Up to 25 monitors can be connected. (Depending on the
length of the cable used and the surrounding environment.)
RS-232 straight cable
(commercially available)
First monitor: primary
Second monitor: secondary
Third monitor: connects to
secondary RS-232C input terminal
RS-232C
input
terminal
RS-232C
output terminal
RS-232C
output
terminal
2. Set the ID No.
Perform operation with the rear side buttons on the primary
monitor. To automatically assign ID numbers in order
from the primary, set AUTO ASSIGN ID No. to ON in ID
SETTING on the SETUP menu. (See page 29.)
(If you attach PN-ZR02 the control kit (optional), you can
perform operation of the monitors with the remote control
unit.)
14
E
Connecting Peripheral Equipment
n
Mounting the control kit (optional) on the
monitor
If performing operation of the monitor with the remote control
unit, the PN-ZR02 control kit (optional) is required.
• Can perform operation of an arbitrary monitor or all
monitors with the remote control unit of the rst monitor.
• Can perform operation of up to 25 monitors.
• Connect the monitors together in a daisy chain with RS-232
cable.
Attach the remote control sensor box as shown in the following
illustration.
For the monitor in
landscape orientation
For the monitor in
portrait orientation
Caution
• When attaching the remote control sensor box, turn the
main power switch OFF.
1. Peel off the sticker ( ) that has been afxed to the
monitor’s remote control sensor box mounting hole.
2. Secure the mounting bracket by inserting the mounting
screw into the monitor’s remote control sensor box
mounting hole.
3. Adjust the angle of the remote control sensor box, and
secure it with the xing screw, so that it may accurately
receive signals from the remote control unit.
Angle adjustment
Mounting bracket
Mounting screw
Fixing screw
Remote control
sensor box
Remote control sensor
box mounting hole
TIPS
• To conceal the remote control sensor box mounting hole,
afx an included sticker over the hole.
4. Insert the remote control sensor box connection cable
into the control kit terminal.
Connection
cable
Remote control
sensor box
Control kit terminal
Caution
• When attaching the remote control sensor box, turn the
main power switch OFF.
• Except for the remote control sensor box connection cable,
do not insert any other cable into the control kit terminal.
Also, do not connect any connection cables that have been
extended with commercially available cables.
15 E
Connecting the Power Cord
Caution
• Use only the power cord supplied with the monitor.
1. Turn off the main power switch.
2. Plug the power cord (supplied) into the AC input terminal.
3. Plug the power cord (supplied) into the power outlet.
2
1
Main power switch
Power cord (Supplied)
AC input terminal
For power
outlet
3
16
E
Binding Cables
The cables connected to the terminals on the rear of the monitor can be fastened with the cable clamp.
Insert the cable clamp into the cable clamp attachment on the rear of the monitor and fasten the cables.
Cable clamp
Cable
Cable clamp
attachment
Cable clamp attachment
Cable
Cable clamp (insertion type)
17 E
Preparing the Remote Control Unit
Installing the batteries
1. Place your nger on the part marked with the ▲, and
then pull the cover off.
2. See the instructions in the compartment and put in the
batteries (R-03 (“AAA” size) x 2) (supplied with the PN-
ZR02 (optional)) with their plus (+) and minus (-) sides
oriented correctly.
3. Close the cover.
TIPS
• When the batteries become exhausted, replace them with
new (commercially available) batteries.
• The supplied batteries (R-03 (“AAA” size) x 2) may become
exhausted quickly depending on how they are stored.
• If you will not be using the remote control for a long time,
remove the batteries.
• Use manganese or alkaline batteries only.
Remote control operation range
The operation range of the PN-ZR02 (optional) remote control
unit is approx. 23 feet (7 m) from the remote control sensor,
and approx 16.4 feet (5 m) at an angle of approx 10° from the
center to the top/bottom/right/left of the remote control sensor.
Remote control sensor
16.4 feet (5 m)
16.4 feet (5 m)
23 feet (7 m)
10°
10°
10°
10°
TIPS
• Do not expose the remote control unit to shock by dropping
or stepping on it. This could lead to a malfunction.
• Do not expose the remote control unit to liquids, and do not
place it in an area with high humidity.
• The remote control unit may not work properly if the remote
control sensor is under direct sunlight or strong lighting.
• Objects between the remote control unit and the remote
control sensor may prevent proper operation.
• Replace the batteries when they run low as this may
shorten the remote control’s operation range.
• If a uorescent light is illuminated near the remote control
unit, it may interfere with proper operation.
• Do not use it with the remote control of other equipment
such as air conditioner, stereo components, etc.
• Adjust the angle of the PN-ZR02 (optional) remote control
sensor and have it face the area where operation with the
remote control unit will take place.
18
E
Caution
• Turn on the monitor rst before turning on the computer or
playback device.
• When switching the main power switch or the POWER
button off and back on, always wait for at least 5 seconds.
A short interval may result in a malfunction.
Turning on the main power
Main power switch
Caution
• The main power must be turned on/off with the main power
switch. Do not connect/disconnect the power cord or turn
the breaker on/off while the main power switch is on.
• For a complete electrical disconnection, pull out the main
plug.
Turning Power On/Off
Turning power on/off
Press the POWER button to turn the power ON/OFF.
You can also turn the power ON/OFF by pressing the
MONITOR ON button/MONITOR OFF button on the remote
control unit.
Power LED POWER button
Status Status of the monitor
Green lit Power on
Orange lit Power off (Standby mode)
Green ashing Input signal waiting mode
TIPS
• When the main power switch is off, the monitor cannot be
turned on.
• If the monitor is in the input signal waiting mode and you
press the POWER button, the monitor enters standby
mode.
• Setting the SCHEDULE ashes the power LED alternately
in red and orange in standby mode.
• To disable the logo screen from displaying when turning the
power ON, set LOGO SCREEN to OFF on the OTHERS
menu. (See page 32.)
• If you change the remote control mode to ALL MONITORS,
power can be turned ON/OFF for all secondary monitors
connected with RS-232 cable. (For operation with the
monitor buttons, use the buttons on the primary monitor.)
19 E
Turning Power On/Off
nMode setting
When the monitor is turned on for the rst time after being
shipped from the factory, the mode setting screen will be
displayed.
(1)Press the or button to select YES or NO.
(2)Press the ENTER button.
YES:
• OPERATION MODE is set to MODE1.
• OFF IF NO OPERATION is set to ON, and POWER
SAVE MODE is set to ON. (These settings cannot be
changed.)
• If there is no operation for 4 hours or more, the monitor
automatically enters standby mode.
• Compared to when POWER SAVE MODE is set to OFF,
the current consumption is reduced while the monitor
is in standby mode, but the startup time from standby
mode becomes longer.
• While the monitor is in standby mode, control via LAN
will be disabled.
• While the monitor is in standby mode, only certain
RS-232C commands can be used.
• While the monitor is in standby mode, the remote
control unit cannot be used to operate the display of the
secondary unit.
NO:
• OPERATION MODE is set to MODE2.
• OFF IF NO OPERATION is set to OFF, and POWER
SAVE MODE is set to OFF.
(These settings can be changed.)
• Compared to when POWER SAVE MODE is set to ON,
the startup time from standby mode is reduced, but more
power will be consumed in standby mode.
Even after being set, changes can be made using
OPERATION MODE, located in MONITOR menu. (See
page 30.)
nDate/time setting
• If the time has yet to be set when the monitor is rst turned
on, the date/time setting screen appears. Set the date and
time.
DATE/TIME SETTING
//
OK:[ENTER] CANCEL:[RETURN]
: :
01 01 17
/00 00
:/ 20
1. Press the or button to select the date and time, and
press the or button to change the numerical values.
2. Press the ENTER button.
• Be sure to set the date and time.
• The date/time setting screen will close automatically if
no operation is performed for about 15 seconds. The
date and time can be set using DATE/TIME SETTING
from the SETUP menu when the date/time setting screen
disappears.
TIPS
• Set the date in “Day/Month/Year” order.
• Set the time on a 24-hour basis.
• The clock is maintained by the internal battery.
• If you already set the time but the date/time setting
screen appears when the power is turned on, the
internal battery may be exhausted. Please contact an
authorized SHARP servicing dealer or service center for
assistance with battery replacement.
• Estimated service life of the internal battery: About 5
years (depending on monitor operation)
• The initial battery was inserted at the factory when the
monitor was shipped, so it may run out of power before
its expected operation life.
Disabling power on/off operations
Power on/power off operations can be disabled in order to
protect the monitor from an accidental power off. Set the
ADJUSTMENT LOCK in FUNCTION menu to “ON 2”. (See
page 37.)
20
E
Basic Operation
When performing operation of multiple monitors with the
remote control unit, rst set the remote control unit to the
appropriate remote control mode (see page 23).
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
TIPS
• You can perform operation of the monitor with the rear
buttons. Utilize the buttons belonging to the monitor that
you would like to operate.
• Operation by using the buttons on the rear side of the
product will perform the same functions.
Rear side buttons
Remote control
unit buttons
This manual assumes that this product will be used with the
remote control unit buttons, except where specically noted.
1. HDMI
Switch the input mode to HDMI1 or HDMI2.
2. Numeric input buttons
When HDMI CEC LINK is set to AUTO, use these buttons to
operate the device connected through the HDMI interface.
0 to 9 are also used in conjunction with the ID SET button.
3. MUTE
Turns off the volume temporarily.
Press the MUTE button again to turn the sound back to the
previous level.
If using the monitor buttons, either hold both the MENU button
and button at the same time or select MUTE AUDIO from
the OTHERS menu.
4. MODE (Color mode selection)
Each time you press this button, the color mode changes in
the following order:
STD (Standard) → VIVID → sRGB →
HIGH ILLUMINANCE → STD...
• HIGH ILLUMINANCE is a display with colors suited to
bright locations.
•
sRGB cannot be used when input mode is D-SUB[COMPONENT].
sRGB is international standard of color representation
specied by IEC (International Electrotechnical
Commission). Color conversion is made in taking account
of liquid crystal’s characteristics and represents color tone
close to its original image.
• If using the monitor buttons, select COLOR MODE from the
COLOR ADJUSTMENT of the PICTURE menu.
• You can press for about 5 seconds to change the remote
control mode. (See page 23.)
5. VOLUME +/- (Volume adjustment)
Pressing + or - displays the VOLUME menu.
VOLUME 15
Press + or - to adjust the volume.
If using the monitor buttons, select VOLUME of the OTHERS
menu.
* If you do not press any buttons for about 4 seconds, the
VOLUME menu automatically disappears.
21 E
6. INFORMATION
Displays monitor information.
INPUT MODE
SIZE
COLOR MODE
BRIGHT
VOLUME
ID No.
REMOTE No.
MODEL
VERSION
S/N
STATUS
:
:
:
:
:
:
:
:
:
:
:
INFORMATION1
1920x1080V: 60 Hz H: 67.5 kHz
D-SUB[RGB]
WIDE
STD
31
15
0
0
PN-V701
×.×.××.×
xxxxxxxx
0000-000000-00-0000
01/01/2017 SUN 00:00:00
END:[RETURN]NEXT:[ ]
LAN
RS-232C/LAN SELECT
DHCP CLIENT
IP ADDRESS
SUBNET MASK
DEFAULT GATEWAY
MONITOR NAME
DATA PORT
MAC ADDRESS
:
:
:
:
:
:
:
:
INFORMATION2
1920x1080V: 60 Hz H: 67.5 kHz
LAN
OFF
192.168.150. 2
255.255.255. 0
0. 0. 0. 0
PN-V701
10008
XX-XX-XX-XX-XX-XX
01/01/2017 SUN 00:00:00
END:[RETURN]
LAN NEXT:[ ]
The display changes from INFORMATION1 →
INFORMATION2 → INFORMATION3 → clear display, and so
on every time you press this button.
When displaying INFORMATION, the display changes from
INFORMATION1 → INFORMATION2 → INFORMATION3
→ INFORMATION1, and so on every time you press the
button. Pressing the RETURN button disappears the display.
• INFORMATION3 shows the information when you have
used the expansion slot to expand the functions.
• The display disappears automatically after about 15
seconds.
•
LAN
is displayed during LAN communication.
• If
LAN
is displayed in red, there is a duplicate IP address.
• If using the monitor buttons, select INFORMATION from
the OTHERS menu.
7. FUNCTION
Use this to display the FUNCTION menu. (See page 37.)
8. ENTER
Conrms the setting.
9. FREEZE
This is not used with this monitor.
10. Buttons for operating the HDMI-connected device
When HDMI CEC LINK is set to AUTO, use these buttons to
operate the device connected through the HDMI interface.
11. ID SET
Set a number on the remote control unit. (See page 36.)
12. OPTION
Switch the input mode to OPTION.
13. DP (DisplayPort)
Switch the input mode to DisplayPort.
Basic Operation
14. SIZE (Screen size selection)
The menu is displayed.
Press the or button to select the screen size. (See page
22.)
If using the monitor buttons, select SIZE from the SCREEN
menu.
15. PIP/PbyP
Each time you press the button, PIP MODES switches in the
following order: OFF → PIP → PbyP → PbyP2 → OFF.
16. BRIGHT +/- (Brightness adjustment)
Pressing + or - displays the BRIGHT menu.
BRIGHT 15
Press + or - to adjust the brightness.
* If you do not press any buttons for about 4 seconds, the
BRIGHT menu automatically disappears.
17. INPUT (Input mode selection)
The menu is displayed. Press the or button to select the
input mode, and press the ENTER button to enter.
* You can select the input mode by pressing the INPUT
button of the monitor.
Input mode Video Audio
DVI-D DVI-D input terminal Audio input
terminal
DisplayPort DisplayPort input terminal
*3
HDMI1 HDMI1 input terminal
HDMI2 HDMI2 input terminal
D-SUB[RGB] D-sub input terminal*2 Audio input
terminal
D-SUB[COMPONENT]
OPTION*1 Expansion slot *3
*1 This is displayed when you have used the expansion slot
to expand the functions.
*2 Select the input mode to be used for D-SUB of INPUT
SELECT. (See page 28.)
*3 Select the terminal for AUDIO SELECT which is used for
audio input. (See page 28.)
18. MENU
Displays and turns off the menu screen. (See page 24.)
19. Cursor
These buttons are used to perform operations such as
selecting items, changing adjustment values, and moving the
cursor.
20. RETURN
Returns to the previous screen.
22
E
Basic Operation
nSwitching the screen size
Even when the screen size is changed, the display may remain the same depending on the input signal.
WIDE Displays image so it lls the entire screen.
ZOOM 1 The image is enlarged to ll the entire screen without changing the aspect ratio.
The edges of the image may be cut off.
ZOOM 2 Use this size if ZOOM 1 cuts off the subtitles.
NORMAL Displays the image so it lls the screen without changing the aspect ratio.
Dot by Dot Displays the dots of the input signals as the corresponding dots on the screen.
TIPS
• Using this monitor’s screen-size switching or dual-screen display functions to compress or expand the screen for commercial
or public viewing in establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright
Law, so please be careful.
• When “Enlarge” is set, the screen size is xed to “WIDE” mode.
• When dual-screen display is selected, the screen size cannot be changed.
• The appearance of the original video may change if you select a screen size with a different aspect ratio than the original
image (e.g. TV broadcast or video input from external equipment).
• When 4:3 video is viewed with the whole screen using the screen-size switching function of this monitor, the edge of the video
may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen size to NORMAL.
• When playing commercial software, parts of the image (like subtitles) may be cropped. In this case select the optimal screen
size using the screen-size switching function of this monitor. With some software, there may be noise or distortion at the
edges of the screen. This is due to the characteristics of the software, and is not a malfunction.
• Depending on the original image size, black bands may remain at the edges of the screen.
23 E
Remote Control Mode
With the remote control unit it’s possible to perform operation
of...
• The primary monitor
• Monitors with a specied ID No.
• All primary/secondary monitors
It’s necessary to specify which type of operation will be
performed in advance.
1. If using the remote control unit, press the MODE button
for approx 5 seconds.
If using the monitor buttons, hold both the MENU
button and button at the same time on the primary.
▲
▲
THIS MONITOR ONLY
REMOTE CONTROL MODE
MODE
EXPAND ITEM
ID No.
ID No. DISPLAY
OK CANCEL
Operate this monitor.
END:[RETURN]
2. Press the or button, select the mode, then perform
settings.
THIS MONITOR ONLY
Performs operation of only the primary using the remote
control unit.
[Example] If the volume is lowered, the volume of the primary
will lower.
Secondary
ID No.: 2
Secondary
ID No.: 3
Primary
ID No.: 1
Secondary
ID No.: 4
VOLUME 10
Lower the volume.
SPECIFIED MONITOR
Performs operation of a monitor with a specied ID No. using
the remote control unit.
Press the or button to select ID No., then press the
or button to select the ID No. of the monitor that you will
operate.
* When it receives signals from the remote control unit,
“Operating specied monitor.” will be displayed on the
primary screen.
[Example] If ID No. is set to 3 and the volume is lowered, the
volume of the monitor for ID No.: 3 will lower.
Secondary
ID No.: 2
Secondary
ID No.: 3
Primary
ID No.: 1
Secondary
ID No.: 4
VOLUME 10
Lower the volume.
When you would like to conrm the ID No. that is set to the
monitor, press the or button to select ID No. DISPLAY, then
press the ENTER button. The ID No. will be displayed on the
screen.
ALL MONITORS
Performs operation of all primary/secondary monitors.
*
ALL [EXPAND ITEM:OFF]
will be displayed on the menu of the primary.
* When it receives signals from the remote control unit,
“Operating all monitors.” will be displayed on the secondary
screen. (Excluding power and input mode selection operation)
* Settings may not be reected depending on the state of the
connected monitors.
[Example] If the power for the primary is turned ON, the power
for all the monitors will be turned ON.
Secondary
ID No.: 2
Secondary
ID No.: 3
Primary
ID No.: 1
Secondary
ID No.: 4
Power ON Power ON
Power ON
Power ON
Turn the power ON.
Press the or button to select EXPAND ITEM, and press
the or button to select to perform this action or not.
OFF ...........For all monitors, only power, input mode
selection, and product information display
operations will be recognized.
ON .............For all monitors, all operations will be
recognized.
After returning to the normal screen with
procedure 3, when 5 minutes have passed from
the end of operation, it will automatically return
to OFF.
* ALL [EXPAND ITEM:ON] will be displayed on the menu
of the primary.
*
Even when REMOTE CONTROL MODE is set
to ALL MONITORS, certain settings such as
LAN settings and ID No. settings will not be
reected on the other monitors.
3. Press the or button to select OK, then press the
ENTER button and return to the normal screen.
4. Perform operation.
Caution
• When the remote control mode is set to ALL MONITORS
and EXPAND ITEM is set to ON, performing remote control
operations that change adjustment values will result in
the secondary adjustment values being the same as the
primary adjustment values.
Secondary
ID No.: 2
Secondary
ID No.: 3
Primary
ID No.: 1
Secondary
ID No.: 4
Secondary
ID No.: 2
Secondary
ID No.: 3
Primary
ID No.: 1
Secondary
ID No.: 4
VOLUME 12 VOLUME 11
VOLUME 10
VOLUME 9
VOLUME 10 VOLUME 10
VOLUME 10
VOLUME 10
Lower the volume.
Be careful of this when adjusting individual displays.
TIPS
• You can copy the setting values of the primary to other
monitors with COPY SETTING VALUE. (See page 29.)
• The buttons on the monitor itself (primary) are also effective
in remote control mode.
24
E
Menu Items
Displaying the menu screen
Video adjustment and settings of various functions are
enabled. This section describes how to use the menu items.
See pages 25 to 36 for details of each menu items.
Caution
• Do not turn the main power switch off while the menu items
are being displayed. Doing so may initialize the settings.
nExample of operation
(Adjusting CONTRAST in the PICTURE menu)
1. Press the MENU button to display the menu screen.
1920x1080 V: 60 Hz H: 67.5 kHz
SCREEN
PICTURE
SETUP
MONITOR
MULTI/PIP
OTHERS
AUTO
CLOCK
PHASE
H-POS
V-POS
H-SIZE
V-SIZE
SIZE
RESOLUTION SETTING
INPUT SIGNAL
RESET
600
25
610
37
50
50
WIDE
SCREEN D-SUB[RGB]
OK:[ENTER] END:[RETURN]
2. Press the or button to select PICTURE, and press
the ENTER button.
3. Press the or button to select CONTRAST.
MODE1
BRIGHT
CONTRAST
BLACK LEVEL
TINT
COLORS
SHARPNESS
COLOR ADJUSTMENT
ADVANCED
UNIFORMITY
RESET
31
30
30
30
30
12
SCREEN
PICTURE
SETUP
MONITOR
MULTI/PIP
OTHERS
PICTURE
BACK:[RETURN]MOVE OSD:[INFORMATION]
1920x1080 V: 60 Hz H: 67.5 kHz
D-SUB[RGB]
4. Press the or button to adjust the setting.
MODE1
BRIGHT
CONTRAST
BLACK LEVEL
TINT
COLORS
SHARPNESS
COLOR ADJUSTMENT
ADVANCED
UNIFORMITY
RESET
31
40
30
30
30
12
SCREEN
PICTURE
SETUP
MONITOR
MULTI/PIP
OTHERS
PICTURE
BACK:[RETURN]MOVE OSD:[INFORMATION]
1920x1080 V: 60 Hz H: 67.5 kHz
D-SUB[RGB]
For items that have , press the ENTER button, make
settings and then press the RETURN button.
5. Press the MENU button to close the menu screen.
TIPS
• The menu will differ depending on the input mode.
• The menu screen will close automatically if no operation is
performed for about 15 seconds. (DATE/TIME SETTING,
SCHEDULE and LAN SETUP screens will close in about 4
minutes.)
nMenu screen display
MODE1
BRIGHT
CONTRAST
BLACK LEVEL
TINT
COLORS
SHARPNESS
COLOR ADJUSTMENT
ADVANCED
UNIFORMITY
RESET
31
30
30
30
30
12
SCREEN
PICTURE
SETUP
MONITOR
MULTI/PIP
OTHERS
PICTURE
BACK:[RETURN]MOVE OSD:[INFORMATION]
1920x1080 V: 60 Hz H: 67.5 kHz
D-SUB[RGB]
123
4
1 Name of the menu
2 Input mode
3 An item being selected (highlighted)
4 Screen resolution of input signal, and other data.
TIPS
• Items that cannot be selected appear in gray.
(e.g. Function not supported by the current input signal)
25 E
Menu item details
The menu will differ depending on the input mode.
nSCREEN
You can move the menu screen display position each time the INFORMATION button is pressed.
AUTO (D-SUB[RGB])
The CLOCK, PHASE, H-POS, and V-POS are automatically adjusted.
Pressing the ENTER button performs adjustment. Use this automatic adjustment when you use the D-SUB[RGB] to display a
computer screen for the rst time or when you change the setting of the computer. (See page 36.)
CLOCK (D-SUB[RGB])
Adjusts frequency for sampling clock for applicable video.
Adjust when there is ickering in the form of vertical stripes.
When using the adjustment pattern (see page 36), make adjustments so that no vertical stripe noise appears in it.
PHASE (D-SUB[RGB])
Adjusts sampling clock phase for applicable video. Useful when small characters appear with low contrast and/or there are
ickers at corners. When using the adjustment pattern (see page 36), make adjustments so that no horizontal stripe noise
appears in it.
* Adjustments to PHASE should be made only after CLOCK has been correctly set.
H-POS
Adjust the horizontal position of the image.
V-POS
Adjust the vertical position of the image.
H-SIZE
Adjust the horizontal size of the image.
V-SIZE
Adjust the vertical size of the image.
SIZE
Selects screen size. (See page 22.)
RESOLUTION SETTING (D-SUB[RGB])
H-RESOLUTION
Sets proper horizontal resolution when the resolution of input signals is not recognized properly.
(Adjustment may be impossible with some signals.)
V-RESOLUTION
Sets proper vertical resolution when the resolution of input signals is not recognized properly.
(Adjustment may be impossible with some signals.)
INPUT SIGNAL (D-SUB[RGB])
If a computer connected to the D-SUB[RGB] outputs any of the following resolutions, make a selection from the following
options.
480 LINES .......... AUTO, 640x480 or 848x480
768 LINES ..........AUTO, 1024x768, 1280x768, or 1360x768
1050 LINES ........1400x1050 or 1680x1050
ZOOM2 SPECIAL SETTING (See page 35.)
RESET
Resets the values of the SCREEN menu items to the factory preset values.
Select ON and then press the ENTER button.
Menu Items
26
E
n
PICTURE
You can move the menu screen display position each time the INFORMATION button is pressed.
BRIGHT
Adjusts the backlight brightness.
CONTRAST
Adjusts the difference between the bright and dark portions of the image.
BLACK LEVEL
Adjusts the entire brightness of the video signals.
TINT
Adjusts the hue. Selecting + changes the color towards green, and selecting - changes it towards magenta.
COLORS
Adjusts the color intensity.
SHARPNESS
Adjusts the sharpness of the image.
COLOR ADJUSTMENT
COLOR MODE
Changes the color mode on the screen. The color mode on the screen can also be changed using a remote control unit. (See
page 20.)
* sRGB cannot be used when input mode is D-SUB[COMPONENT]. See page 20 for details.
WHITE BALANCE
THRU ................................. Displays the input signal level as is.
PRESET ............................. Selects the color temperature using PRESET.
USER ................................. Adjusts R-/G-/B-CONTRAST and R-/G-/B-OFFSET respectively using USER.
ADJUST UNIFORMITY ...... Adjusts UNIFORMITY, R-/G-/B-CONTRAST, R-/G-/B-OFFSET, and BRIGHTNESS VALUE
respectively using ADJUST UNIFORMITY.
PRESET
Selects the color temperature when the WHITE BALANCE is set to PRESET.
The setting values are shown for reference. The color temperature of the screen varies over time. This function is not
intended to keep the color temperature constant.
USER
Adjusts each item when the WHITE BALANCE is set to USER.
R-CONTRAST .... Adjusts bright-toned red component.
G-CONTRAST ... Adjusts bright-toned green component.
B-CONTRAST .... Adjusts bright-toned blue component.
R-OFFSET ......... Adjusts dark-toned red component.
G-OFFSET ......... Adjusts dark-toned green component.
B-OFFSET ......... Adjusts dark-toned blue component.
ADJUST UNIFORMITY
Adjusts each item when the WHITE BALANCE is set to ADJUST UNIFORMITY.
UNIFORMITY ..................... Sets the discoloration correction level. (See page 27.)
R-CONTRAST .................... Adjusts bright-toned red component.
G-CONTRAST ................... Adjusts bright-toned green component.
B-CONTRAST .................... Adjusts bright-toned blue component.
R-OFFSET ......................... Adjusts dark-toned red component.
G-OFFSET ......................... Adjusts dark-toned green component.
B-OFFSET ......................... Adjusts dark-toned blue component.
BRIGHTNESS VALUE ....... Adjusts the screen brightness.
COPY TO USER
Copies the value of white set for PRESET to the USER setting.
Select ON and then press the ENTER button.
(In the case other than white, color tone may differ from the PRESET.)
GAMMA
Selects the gamma. USER sets the gamma to the sent value. (See page 41.)
FLESH TONE
Adjust the hue control.
C.M.S.-HUE
Adjusts color tone with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).
C.M.S.-SATURATION
Adjusts color vividness with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).
Menu Items
27 E
Menu Items
ADVANCED
AUTO (D-SUB[RGB])
The ANALOG GAIN and ANALOG OFFSET are automatically adjusted.
Pressing the ENTER button performs adjustment.
ANALOG GAIN (D-SUB[RGB])
Adjusts the bright portions of the video input signal.
ANALOG OFFSET (D-SUB[RGB])
Adjusts the dark portions of the video input signal.
NR
Reduce the image noise.
Setting a higher level reduces more noise. However, it may cause blurring on an image.
RGB INPUT RANGE (DVI-D/HDMI/D-SUB[RGB]/DisplayPort/OPTION)
Sets the RGB input signal range.
When using HDMI, DisplayPort or OPTION set to AUTO, the RGB input signal is detected automatically. Use AUTO normally.
If the RGB input signal range cannot be set appropriately even when using AUTO, set according to the image. When the
setting is different, images will be displayed with washed out blacks and compressed gradients.
DISPLAY COLOR PATTERN
Displays a color pattern. Can be displayed while the menu screen is displayed, so you can refer to the pattern while adjusting
the image. When WHITE, RED, GREEN, or BLUE is displayed, you can set the level in the range of 0 to 255.
OFF ...............No pattern display.
WHITE ...........White single color pattern display.
RED...............Red single color pattern display.
GREEN .........Green single color pattern display.
BLUE .............Blue single color pattern display.
USER ............Red/green/blue mixed color pattern display. When USER is selected, set each color’s level.
UNIFORMITY
Sets the LCD panel’s discoloration correction level.
OFF ............................... Discoloration will not be corrected.
MODE1 to MODE3 ........ The effect of the discoloration correction will increase from MODE1<MODE2<MODE3.
However, brightness and contrast will also decrease from MODE1<MODE2<MODE3.
RESET
Resets the values of the PICTURE menu items to the factory preset values.
Select ON and then press the ENTER button.
28
E
Menu Items
nSETUP
DATE/TIME SETTING
Set the date and time. Press the or button to select the date and time, and press the or button to change the
numerical values.
Set the date in “Day/Month/Year” order.
Set the time on a 24-hour basis. (Factory default)
DATE/TIME FORMAT
Sets the date/time display format.
DATE ..................MM/DD/YYYY, DD/MM/YYYY, YYYY/MM/DD
(YYYY: Year, MM: Month, DD: Day)
TIME ...................Select 12- or 24-hour time.
SCHEDULE (See page 35.)
You can turn the power on/off and change the screen brightness at a specied time.
LANGUAGE
Sets the display language for the menu screen.
INPUT SELECT
D-SUB
Select the input mode to be used in D-sub input terminal.
HDMI CEC LINK
AUTO ............Use the HDMI CEC function.
If the device connected to the HDMI input terminal supports CEC, the input mode of the monitor changes to
HDMI when playback starts on the device.
OFF ...............HDMI CEC function is not used.
AUTO POWER ON
This can be set when HDMI CEC LINK is set to AUTO.
If the device connected to the HDMI input terminal supports CEC, you can specify whether or not the monitor power turns on
when the device power is turned on.
HDMI AUTO VIEW
When ON is selected, the screen size is adjusted automatically according to the screen size control signal included in the
video signal input from the HDMI1 and HDMI2 input terminals or the expansion slot (when the expansion function is used).
HOT PLUG CONTROL
Sets whether to use hot plug control for the DVI-D, HDMI1 and HDMI2 input terminals, and the expansion slot (when the
expansion function is used).
DisplayPort STREAM
Selecting MST (Multi Stream Transport) allows different images to be displayed when daisy chaining two devices through the
monitor’s DisplayPort. Image may not be displayed properly depending on the computer (video card) to be connected.
DisplayPort SETTING
Sets FILTER SETTING, GAIN, and OFFSET for the signal from the DisplayPort input terminal.
AUDIO SELECT
Selects the terminal used to input audio signals in each input mode.
AUDIO OUTPUT
Sets the volume of sound output from the audio output terminal.
VARIABLE .......... You can adjust the volume from the audio output terminal by using VOLUME.
FIXED ................. Fixes the volume from the audio output terminal. Adjust the volume by using an external device.
START INPUT MODE
You can set the input mode that will be in effect when the power is turned on.
When this is set to LAST INPUT MODE, the input mode when the power was last turned off will appear.
29 E
Menu Items
COMMUNICATION SETTING
RS-232C/LAN SELECT
Selects the method with which to control the monitor from the computer.
BAUD RATE
Selects the communication speed used for RS-232C communication.
LAN SETUP
Congures the settings to control the monitor from the computer via LAN. (See page 51.)
AUTO ASSIGN FIXED IP ADDR.
Can be enabled when RS-232C/LAN SELECT is LAN and the DHCP CLIENT is OFF.
Set DHCP CLIENT to OFF for the monitor connected to the RS-232C output terminal and the daisy chain of connected
monitors that follows. Fixed IP addresses are automatically allocated.
If the IP address is a duplicate with a network device other than a monitor, individually change the IP address.
Crestron Connected
Select this when using a Crestron device. When this function is set to ON, the monitor can be controlled via network using
equipment and application software of Crestron Electronics, Inc.
This monitor supports application software RoomView from Crestron Electronics, Inc.
This is a function to connect a system developed by Crestron Electronics, Inc. which manages and controls multiple system
devices connected to the network.
For details of Crestron Connected, refer to the Crestron Electronics, Inc. website. (Provided only In English.)
http://www.crestron.com/
For the download of RoomView Express, refer to the Crestron Electronics, Inc. website. (Provided only In English.)
http://www.crestron.com/getroomview
ID SETTING
ID No. SET
Assigns ID numbers to monitors connected in a daisy chain (see page 38), using the RS-232 cables.
The numbers 1 to 255 are available for ID numbers.
If “0” is set, the system regards this as the state where no ID number is set.
AUTO ASSIGN ID No.
ID No. to be used will be automatically assigned when multiple monitors are connected with RS-232C.
Select ON, then press the ENTER button.
Perform operations using the rst monitor in the daisy chain.
REMOTE No.
Sets the number of the remote control unit. (See page 36.)
COPY SETTING VALUE
When the monitor has been connected to multiple monitors by RS-232C, the settings in the monitor can be copied to the
monitor connected to the RS-232C output terminal and to the daisy chain of connected monitors that follows.
Selects the settings to copy with COPY SETTING VALUE TARGET.
“PICTURE” ONLY ..... Copies the PICTURE menu settings.*
ALL ........................... Copies all the settings.*
Select the ID No. of the monitor that you would like copy to with COPY TO ID No., then select COPY and press the ENTER button.
If you select ALL, settings will be copied to all monitors.
When you would like to conrm the ID No. that is set to the monitor, select ID No. DISPLAY and press the ENTER button. The
ID No. will be displayed on the screen.
* Certain setting details such as ANALOG GAIN, ANALOG OFFSET, and DISPLAY COLOR PATTERN cannot be copied.
30
E
nMONITOR
PORTRAIT/LANDSCAPE INSTALL
LANDSCAPE ......Landscape orientation
PORTRAIT .........Portrait orientation
ROTATE 180°
If video is upside down when the monitor is installed in portrait orientation, you can rotate the video 180 degrees.
Interlaced signals may not be displayed properly.
INVERSE SCAN
INVERSE SCAN
Normally this is set to OFF. To perform inverse scan, set to ON.
When ROTATE 180° is set to ON, cannot perform inverse scan.
PICTURE FLIP
When INVERSE SCAN is set to ON, the picture can be ipped vertically.
In portrait orientation, the picture is ipped horizontally.
OSD H-POSITION
Adjusts the horizontal display position of menu screen.
OSD V-POSITION
Adjusts the vertical display position of menu screen.
OPERATION MODE
MODE1 ...... OFF IF NO OPERATION is set to ON, and POWER SAVE MODE is set to ON.
(These settings can not be changed.)
MODE2 ...... Will perform standard operation. OFF IF NO OPERATION is set to OFF, and POWER SAVE MODE is set to OFF.
These settings can be changed.
POWER SAVE MODE
When OFF is selected, startup time from standby mode is reduced. Note, however that, more power will be consumed in
standby mode.
When ON is selected, current consumption is reduced while the monitor is in standby mode. Note, however, that the startup
time from standby mode becomes longer.
If set to ON, certain RS-232C commands cannot be used in standby mode, and control via LAN will be disabled. (See pages
38 and 51.)
OFF IF NO OPERATION
Determines whether or not to set the monitor to go into standby mode when there is no operation from the remote control unit,
RS-232C commands, or LAN.
When the setting is ON, set the time until standby mode is entered in TIME.
POWER ON DELAY
When ON is set, you can delay the screen display after the monitor is turned on.
When ON is selected, set the delay time with INTERVAL (interval can be set up to 60 seconds in units of 1 second).
When this function is activated, the power LED ashes (at approx. 0.5 second interval) in green.
SELF ADJUST
On a D-SUB[RGB] screen, specify whether to perform screen adjustment automatically or not.
When ON is selected, the screen is automatically adjusted when its resolution is 800 x 600 or higher and the timing of input
signals changes. “ADJUSTING” appears on the screen during the adjustment.
If SELF ADJUST is set to ON, set the time it takes to start the SELF ADJUST function in START TIMING.
For images with black edges, etc., depending on the signal, adjustment may not be possible. In this case select OFF. (Perform
manual adjustment of the screen.)
Menu Items
31 E
nMULTI/PIP
MULTI
ENLARGE (See page 34.)
Sets whether or not to use the enlarge function.
ADVANCED (ENLARGE)
ENLARGE H / ENLARGE V
.......... Sets the number of screen splits (number of monitors) in the horizontal/vertical direction used for the enlargement.
ENLARGE-POS
.......... Specify the split screen to be displayed when the enlargement function is used.
H-POS / V-POS
.......... Adjust the horizontal/vertical position of the enlarged screen.
BEZEL ADJUST
Sets whether or not to use the frame correction function.
ADVANCED (BEZEL ADJUST)
BEZEL ADJUST (TOP) / BEZEL ADJUST (BOTTOM) /BEZEL ADJUST (RIGHT) / BEZEL ADJUST (LEFT)
.......... Adjusts so that the top/bottom/left/right connecting joints of grouped units will be displayed smoothly when a group
of monitors are aligned in multiples to display a single image.
BEZEL (TOP) / BEZEL (BOTTOM) / BEZEL (RIGHT) / BEZEL (LEFT)
.......... Sets the frame width of the display.
PIP/PbyP
PIP MODES
Sets the display method.
OFF ......... Displays one screen.
PIP ..........Displays a sub screen inside a main screen.
PbyP ........Displays a main screen and a sub screen in a line.
PbyP2......Displays a main screen which measures 1280 pixels in the longest direction and a sub screen in a line.
PIP SIZE
Sets the size of the sub screen in PIP mode.
PIP H-POS
Adjusts the horizontal position of the sub screen in PIP mode.
PIP V-POS
Adjusts the vertical position of the sub screen in PIP mode.
PIP BLEND
In PIP mode, use this menu item to display the sub screen transparently.
PIP SOURCE
Selects the input signal of the sub screen in PIP, PbyP, or PbyP2 mode.
SOUND CHANGE
Sets the sound which is output in PIP, PbyP, or PbyP2 mode.
MAIN POS
Sets the position of the main screen in PbyP or PbyP2 mode.
PbyP2 POS
Sets the position of the sub screen in PbyP2 mode.
Menu Items
32
E
Menu Items
nOTHERS
SCREEN MOTION
PATTERN
Residual images are reduced by moving the screen.
OFF ................. SCREEN MOTION function is disabled.
PATTERN1 ...... The whole screen moves vertically and horizontally.
PATTERN2 ...... A black screen spreads from the bottom of the screen and then shrinks to the bottom of the screen. If the
monitor is installed in the portrait orientation, a black screen spreads from the left end of the screen and then
shrinks to the left end of the screen.
PATTERN3 ...... A black bar moves from the left end to the right end of the screen. If the monitor is installed in the portrait
orientation, a black bar moves from the top to the bottom of the screen.
PATTERN4 ...... Black screens appear from both sides of the screen, and the displayed image is compressed into the central
eld. If the monitor is installed in the portrait orientation, the screen is compressed from the top and bottom
ends.
PATTERN1 PATTERN2 PATTERN4PATTERN3
MOTION TIME 1
Specify a time period (operating interval) until SCREEN MOTION starts.
MOTION TIME 2
Specify a time period during which SCREEN MOTION operates (time period during which the screen will move).
POWER MANAGEMENT
POWER MANAGEMENT determines whether or not to switch modes from no signal to the input signal waiting mode.
CONNECT AUTO INPUT SELECT
Sets whether the input into the input terminal automatically changes when a video signal is input into that terminal. The input
via the expansion slot is ignored.
(With some input signals, the input may not change.)
NO SIGNAL AUTO INPUT SEL.
Specify whether to change inputs automatically. When ON is selected and no signal is present in the selected input mode, the
monitor automatically changes the selected mode to another mode where a video signal is present.
When there are video signals in multiple input modes, switching takes place according to the order of priority set in AUTO
INPUT SELECT PRIORITY.
AUTO INPUT SELECT PRIORITY
Sets the order of input terminal priority for NO SIGNAL AUTO INPUT SEL..
When an option that supports this function is connected to the expansion slot, you can set the order in OPTION.
(If the option does not support this function, “OPTION” will not appear.)
Input does not change automatically for terminals without a priority setting.
LOGO SCREEN
Sets whether or not to display the logo screen.
SCAN MODE (HDMI1 / HDMI2 / D-SUB[COMPONENT] / OPTION)
Sets the scan mode used for video input.
MODE1 ............... Over-scan display.
MODE2 ...............Under-scan display.
MODE3 ............... Under-scan display when the input signal is 1080i/p. Otherwise, over-scan display.
*
Even when MODE1 is selected, under-scan display is used when the input signal is 1080i/p and the screen size is Dot by Dot.
VOLUME
Adjusts the volume.
MUTE AUDIO
Can temporarily turn off the volume.
INFORMATION
Displays monitor information. (See page 21.)
33 E
TIPS
• When WHITE BALANCE is set to THRU, BLACK LEVEL, CONTRAST, TINT, COLORS, GAMMA, PRESET, USER, COPY
TO USER, FLESH TONE, C.M.S. and ADJUST UNIFORMITY cannot be set.
• If COLOR MODE is set to sRGB, the following items cannot be set.
PRESET, USER, COPY TO USER, and GAMMA
• When the COLOR MODE is set to VIVID or HIGH ILLUMINANCE, GAMMA cannot be adjusted.
• When displaying the color pattern, it is possible to adjust certain items of the PICTURE menu.
Non-adjustable items cannot be selected.
• CONNECT AUTO INPUT SELECT and NO SIGNAL AUTO INPUT SEL. do not work for the Sync-on-green signal of
D-SUB[RGB] or the signals of D-SUB[COMPONENT].
Menu Items
34
E
nDual screen display
You can display two screens simultaneously.
Set this function with PIP MODES of PIP/PbyP in the MULTI/
PIP menu.
PIP
Main screen
Sub
screen
A sub screen is displayed
inside a main screen.
PbyP
Main
screen
Sub
screen
A main screen and a sub
screen are displayed in a
line.
PbyP2
Main screen Sub
screen
Displays a main screen
which measures 1280
pixels in the longest
direction and a sub
screen in a line.
* The currently selected input signal is displayed on the main
screen.
* The following combinations are available for display:
DisplayPort - DVI-D
DisplayPort - HDMI1 or HDMI2
DisplayPort - D-SUB[RGB]
DisplayPort - D-SUB[COMPONENT]
DisplayPort - OPTION
DVI-D - D-SUB[RGB]
DVI-D - D-SUB[COMPONENT]
HDMI1 or HDMI2 - D-SUB[RGB]
HDMI1 or HDMI2 - D-SUB[COMPONENT]
D-SUB[RGB] or D-SUB[COMPONENT] - OPTION
TIPS
• You might infringe on a copyright of the author which is
protected by copyright law when you display the images of
the computer screen and television/VCR simultaneously for
prot-making or to show the image to the public.
• The screen size for dual-screen display is the same as
the screen size for single-screen display. The Dot by Dot
screen is displayed in NORMAL size except when it is set
as the PIP main screen.
• When dual-screen display is selected, the SCREEN
MOTION function is disabled.
• When dual-screen display is selected, the CONNECT
AUTO INPUT SELECT function and NO SIGNAL AUTO
INPUT SEL. function are disabled.
• When dual-screen display is selected, the screen cannot
be enlarged.
• When dual-screen display is selected, D-SUB of the INPUT
SELECT options cannot be set.
• When dual-screen display is selected and an interlaced
signal (1080i, 480i) is input to the main or sub screen, the
image is not displayed properly.
• When a signal of 3840×2160 or 4096×2160 is input to the
sub screen, the sub screen does not display an image.
• In the following cases, you cannot set PIP MODES to PIP,
PbyP, or PbyP2.
- When DisplayPort STREAM is set to MST.
- When ROTATE 180° is set to ON.
- When PICTURE FLIP is set to ON.
• When HDMI CEC LINK is set to AUTO, SOUND CHANGE
on the PIP/PbyP may be changed to MAIN due to the
switching of the monitor’s input or due to the operation of
the HDMI-connected device.
nEnlarge
• You can align several monitors and integrate them into a
single large screen to display.
• Up to 5 monitors can be aligned in both the horizontal and
vertical directions.
• Each monitor displays enlarged views of separated images.
(Example)
Horizontal direction: 2 monitors
Vertical direction: 2 monitors
Horizontal direction: 3 monitors
Vertical direction: 2 monitors
Setting procedure
Set using MULTI in the MULTI/PIP menu.
1. Set ENLARGE to ON.
2. Select ADVANCED (ENLARGE).
3. Set the number of monitors aligned in the horizontal
direction in ENLARGE H.
4. Set the number of monitors aligned in the vertical
direction in ENLARGE V.
5. Set the section of the separated image to be displayed
on each monitor in ENLARGE-POS.
1) Press the ENTER button.
2) Press the , , or button to select position,
then press the MENU button.
TIPS
• When Enlarge is used, the SCREEN MOTION function is
disabled.
• When Enlarge is used, the CONNECT AUTO INPUT
SELECT function and NO SIGNAL AUTO INPUT SEL.
function are disabled.
• When Enlarge is used, the HDMI AUTO VIEW function is
disabled.
Menu Items
35 E
nZOOM2 SPECIAL SETTING
If you connect a laptop computer with any of the following
screen resolutions and black bands appear around the screen,
set ZOOM2 SPECIAL SETTING of INPUT SIGNAL on the
SCREEN menu to ON and then select ZOOM2 in the SIZE
setting.
This displays the area inside the black band.
Laptop computer
resolution
Corresponding signal*1
1280x800 1280x1024, 1280x960, 1400x1050*2
1280x600 1280x720
1024x600 1024x768
*1: This setting is effective only when the screen resolution,
including the black band, is one of the resolutions listed
above.
*2: Use the automatic screen adjustment.
nSCHEDULE
You can set the time to switch the monitor on and off.
Set this function with SCHEDULE in the SETUP menu. (See
page 28.)
-
:
– –– –– –– ––
––
––
SCHEDULE
No.
POWER DAY OF THE WEEK
TIME INPUT BRIGHT
– –
/
– –
/
– – – – – – –
– –
:
– –
:
– –
D-SUB[RGB]
(1)
–
-
:
– –– –– –– ––
––
–––
-
:
– –– –– –– ––
––
–––
-
:
– –– –– –– ––
––
–––
-
:
– –– –– –– ––
––
–––
-
:
– –– –– –– ––
––
–––
-
:
– –– –– –– ––
––
–––
-
:
– –– –– –– –
– –
– –
– –
– –
– –
– –
– –
– ––
––
–––
(5)(2) (3) (4) (6)
OK:[ENTER] CANCEL:[RETURN]
1. Press the or button to select the SCHEDULE
number, and press the button.
2. Set the SCHEDULE. (See the description below.)
Press the or button to select items, and press the or
button to change the setting.
3. Press the ENTER button.
SCHEDULE becomes effective.
(1)
●: SCHEDULE effective
-
: SCHEDULE not effective
(2) POWER
ON : Switches the monitor on at the specied time.
OFF : Switches the monitor off at the specied time and puts
the monitor in standby mode.
(3) DAY OF THE WEEK
Species the day of the week to execute the SCHEDULE.
0:ONLY ONCE
Executes the SCHEDULE once on the specied day.
Specify the day of the week to execute the SCHEDULE.
1:EVERY WEEK
Executes the SCHEDULE on the specied day of the week
every week. Specify the day of the week to execute the
SCHEDULE.
Periodic setting such as “Monday through Friday” is also possible.
2:EVERY DAY
Executes the SCHEDULE every day regardless of the day
of the week.
(4) TIME
Species the time to execute the SCHEDULE.
Set the time on a 24-hour basis. (Factory default)
Can be entered as 12-hour time using the TIME setting in
DATE/TIME FORMAT.
(5) INPUT
Species the input mode at power-on. If you don’t specify
this the input active at the last power-off will appear.
When START INPUT MODE is set to a value other than
LAST INPUT MODE, the input mode congured for START
INPUT MODE will be set.
Input modes displayed on D-SUB will depend upon the
INPUT SELECT settings.
(6) BRIGHT
Sets the brightness when changing the screen brightness at
a specied time.
Caution
• Do not switch off the main power after setting the
SCHEDULE.
• Specify the correct date and time. (See page 28.)
SCHEDULE does not function unless the date and time are
specied.
• Check regularly that the set date and time are correct.
• When a temperature abnormality occurs and the backlight
brightness is reduced, the brightness is not changed even
if a schedule set to BRIGHT is executed.
TIPS
• Up to 8 SCHEDULE items can be registered.
• Setting the SCHEDULE ashes the power LED alternately
in red and orange in standby mode.
• A SCHEDULE that has a large number has precedence
over that of a small number when schedules overlap.
Menu Items
36
E
nAbout remote control numbers
If there is another monitor nearby, you can change the remote
control number to prevent the other monitor from being
operated by the remote control unit.
Set the same number in the monitor and in the remote control
unit.
TIPS
• You can set remote control numbers to values from 0 to 9.
• When the remote control unit batteries become exhausted
and when you replace the batteries, the number on the
remote control unit may be reset to 0.
Changing the remote control number on the monitor
* Set this on a monitor (primary) with a remote control sensor
box (provided with the PN-ZR02 (optional)) connected.
Use REMOTE No. on the SETUP menu to set the number.
(See page 29.)
1. Use the or button to select the remote control
number.
2. Select ON and press the ENTER button.
The remote control number is set on the monitor.
Changing the remote control number on the remote
control unit
1. While holding down the ID SET button, hold down the
number that corresponds to the remote control number
set on the monitor for 5 seconds or more, and then
release these buttons.
The remote control number is set on the remote control unit.
Checking the remote controller number
* Perform these steps on the remote control unit.
(The monitor buttons cannot be used to to check the
number.)
1.
Press the INFORMATION button to display INFORMATION1.
2. Check that REMOTE No. is the remote control number
that you have set in the above procedure.
3. Press the RETURN button to close the monitor
INFORMATION screen.
TIPS
• If the remote control numbers on the monitor and remote
control unit are different, they will both be displayed on
INFORMATION1. On this screen, you can press the
ENTER button to match the number on the monitor with the
number on the remote control unit.
• Even if the remote control numbers are different, you can
use the remote control unit to display the INFORMATION
screen.
Adjustments for computer screen
display
nAutomatic adjustment
When you use the D-SUB[RGB] to display a computer screen
for the rst time, or when you change the setting of the
computer, use the automatic screen adjustment.
1. Switch the input to D-SUB[RGB] and display the
adjustment pattern. (See the description below.)
2. Press the MENU button and use the or button to
display the SCREEN menu.
3. Press the ENTER button and select “AUTO”.
4. Press the ENTER button.
The automatic adjustment is complete in several seconds.
5. Press the MENU button to close the menu screen.
TIPS
• If the screen cannot be adjusted properly with one
automatic adjustment, repeat the automatic adjustment two
or three times. Try manual adjustment if necessary.
nScreen display for adjustment
Before making adjustments in the SCREEN menu or
PICTURE menu, display an image to brighten the entire
screen. If you are using a Windows computer, use the
adjustment pattern on the supplied CD-ROM.
Opening the adjustment pattern
The following example is performed in Windows 7.
1. Load the supplied CD-ROM into the computer’s CD-
ROM drive.
2. Open [CD Drive] in [Computer].
3. Double-click [Adj_uty.exe].
The adjustment pattern will appear.
Adjust the screen automatically or manually.
4. When adjustment is nished, press the [Esc] on the
computer’s keyboard to quit the adjustment program.
5. Eject the CD-ROM from the CD-ROM drive.
TIPS
• If the display mode on the computer you are using is 65000
colors, the color levels in the color pattern may appear
differently or grayscale may appear to be colored. (This
is due to the specications of the input signal and is not a
malfunction.)
Menu Items
37 E
You can return the settings to their factory-preset values and
restrict operations.
1. If using the remote control unit:
Press the FUNCTION button, and then press the MENU
button within 10 seconds.
If using the monitor buttons:
Press the MENU button and INPUT button at the same
time until “F” is displayed in the upper left area of the
screen, then while “F” is being displayed, press the
MENU button.
▲▲▲▲▲▲▲▲
▲▲▲▲▲▲▲▲
OFF
UNLOCKED
ON 1
ON
LED
LED
MONITOR
1
FUNCTION
ALL RESET
ADJUSTMENT LOCK
ADJUSTMENT LOCK TARGET
RS-232C/LAN
OSD DISPLAY
LED
TEMPERATURE ALERT
STATUS ALERT
POWER BUTTON
EXTERNAL CONTROLLER INPUT
SIGNAL RESPONSE LEVEL
OK:[ENTER] END:[RETURN]
2. Select and set the items.
ALL RESET
Resets the settings to the factory default settings.
Press the ENTER button, select the resetting method,
and then press the ENTER button.
After initialization, turn the main power switch off and
then back on.
ALL RESET1 ....Resets all the settings to the factory
default settings.
ALL RESET2 ....Returns all settings to the factory default
settings except for the following items:
LAN SETUP, RS-232C/LAN SELECT,
ID No. SET, REMOTE No., BAUD
RATE, NETWORK, MAIL, SERVICE &
SUPPORT, and SNMP (See page 29,
and pages 55 to 58.)
ADJUSTMENT LOCK
You can disable operations on the monitor and the
remote control unit that use buttons.
OFF ...Enables operation.
ON 1 ..Disables all operations other than turning power
on/off and FUNCTION.
ON 2 ..Only the FUNCTION operation is enabled.
Disables all operations other than FUNCTION (not
even power on/off).
ADJUSTMENT LOCK TARGET
Sets the target to prohibit operation of with
ADJUSTMENT LOCK.
REMOTE CONTROL ..... Prohibits remote control
operation
MONITOR BUTTONS ... Prohibits monitor button
operation
BOTH ............................. Prohibits remote control and
monitor button operation
RS-232C/LAN
Species whether to allow control via RS-232C or LAN
(see pages 38 and 51).
Initialization (Reset)/Functional Restriction Setting (FUNCTION)
OSD DISPLAY
Shows/hides the menu, modes and messages.
The FUNCTION and REMOTE CONTROL MODE
screens cannot be hidden.
ON 1 .............. Shows all menus, modes and messages.
ON 2 .............. Hides messages automatically displayed
by the display. Shows messages during
operation.
OFF ............... Hides all menus, modes and messages.
LED
Species whether to light the power LED.
TEMPERATURE ALERT
Selects the notication method for an abnormal
temperature.
OFF .............. Do not notify about an abnormal
temperature.
OSD & LED .. When an abnormal temperature is
detected, the power LED ashes in red
and green alternately and the screen
displays a message: TEMPERATURE.
LED............... When an abnormal temperature is
detected, the power LED ashes in red
and green alternately.
STATUS ALERT
Selects the notication method for a hardware error.
OFF .............. Do not notify about the error.
OSD & LED .. When a hardware error is detected, the
power LED ashes in red and the screen
displays a message: STATUS [xxxx].
LED............... When a hardware error is detected, the
power LED ashes in red.
POWER BUTTON
Normally, leave this setting as MONITOR.
When using an optional part, if instruction appears,
change the setting accordingly.
EXTERNAL CONTROLLER INPUT
Normally, you do not need to change this setting.
When using an optional part, if instruction appears,
change the setting accordingly.
SIGNAL RESPONSE LEVEL
Normally, you do not need to change this setting. Use
this option to set the level of response to signal changes.
3. Press the RETURN button to return to the normal
screen.
TIPS
• When both abnormal temperature and hardware error are
detected, the hardware error notication overrides.
• If TEMPERATURE ALERT or STATUS ALERT is set to
OSD&LED, alert messages will appear even if the OSD
DISPLAY is set to ON 2 or OFF.
• If TEMPERATURE ALERT or STATUS ALERT is set to LED
or OSD & LED, the LED lights even if the LED function is
set to OFF.
38
E
Controlling the Monitor with a computer (RS-232C)
You can control this monitor from a computer via RS-232C
(COM port) on the computer.
You can also connect multiple monitors via a daisy chain by
using a computer. By assigning ID numbers to each monitor
(see page 39), you can make input mode selection/adjustment
or can check the status of a specic monitor.
TIPS
• To control the monitor via RS-232C, set RS-232C/LAN
SELECT to RS-232C.
• You cannot use RS-232C and LAN control simultaneously.
Computer connection
nOne-to-one connection with a computer
Connect with RS-232 straight cable between the computer’s
COM port (RS-232C connector) and the RS-232C input
terminal on the monitor.
RS-232 straight cable
(commercially available)
To COM port
Computer
RS-232C
input
terminal
nDaisy chain connection… Advanced operation
Connect with RS-232 straight cable between the computer’s
COM port (RS-232C connector) and the RS-232C input
terminal on the rst monitor.
Next, connect RS-232 straight cable to the rst monitor’s
RS-232C output terminal and to the second monitor’s
RS-232C input terminal. Connect in the same way to the third
and subsequent monitors.
Up to 25 monitors can be connected. (Depending on the
length of the cable used and the surrounding environment.)
To COM port RS-232 straight cables
(commercially available)
First monitor Second monitor
RS-232C
input
terminal
RS-232C
output
terminal
Computer
Communication conditions
Set the RS-232C communication settings on the computer to
match the monitor’s communication settings as follows:
Baud rate *
Stop bit
1 bit
Data length 8 bits Flow control None
Parity bit None
* Set to the same baud rate as the BAUD RATE setting of
SETUP menu. (Initial setting: 38400 bps)
* When connecting multiple monitors in a daisy chain, set all
monitors to the same BAUD RATE.
Communication procedure
nCommand format
When a command is sent from the computer to the monitor,
the monitor operates according to the received command and
sends a response message to the computer.
C1 C2 C3 C4 P1 P2 P3 P4
Return code
Command field
(4 prescribed
alphanumerical characters
)
Parameter field
(4 character string comprised of:
0-9, +, -, space, ?)
Example: VOLM0030
VOLM
30
* Be sure to input 4 characters for the parameter. Pad with
spaces (“ ”) if necessary.
(“ ” is a return code (0DH, 0AH or 0DH))
Wrong : VOLM30
Right : VOLM 30
When inputting a negative value, specify a numerical value in
three digits.
Example: OFSR-005
Do not use spaces for MPOS, DATE, and SC01 through
SC08. Specify parameters using a specied number of
characters.
Example: MPOS010097
If a command has “R” listed for “Direction” in the
“RS-232C command table” on page 42, the current value can
be returned by using “?” as the parameter.
Example:
VOLM ? ? ? ? ←From computer to monitor (How
much is current volume setting?).
30 ←From monitor to computer
(Current volume setting: 30).
* If an ID number (see page 39) has been assigned
(For example, ID number = 1).
VOLM ?←From computer to monitor.
30 001 ←From monitor to computer.
39 E
Controlling the Monitor with a computer (RS-232C)
nResponse code format
When a command has been executed correctly
O K Return code
(0DH, 0AH)
A response is returned after a command is executed.
* If an ID number has been assigned
O K SPC 0 0 1
ID number of respondin
g
monitor
Space (20H)
Return code
(0DH, 0AH)
When a command has not been executed
R R E Return code
(0DH, 0AH)
* If an ID number has been assigned
R R E SPC 0 0 1
ID n
u
m
be
r
Space (20H)
Return code
(0DH, 0AH)
TIPS
• “ERR” is returned when there is no relevant command or
when the command cannot be used in the current state of
the monitor.
• If communication has not been established for reasons
such as a bad connection between the computer and
monitor, nothing is returned (not even ERR).
• “ERR” may be returned when a command cannot be
received correctly due to interference from the surrounding
environment.
Please ensure that the system or software retries the
command if this occurs.
• If no monitor has been assigned the designated ID number
(e.g. if the command IDSL0002 is used, but no monitor
with ID number: 2 is found), no response is returned.
If execution of the command is taking some time
I W T A Return code
(0DH, 0AH)
When the following commands are used, “WAIT” is returned.
In this case, a value will be returned if you wait a while. Do not
send any command during this period.
No ID number is attached to WAIT response.
• Commands which return WAIT:
1. When repeater control is used
2. When an IDSL or IDLK command is used
3. When one of the following commands is used: RSET,
INPS, ASNC, WIDE, EMAG, EPOS, PXSL, POWR,
AGIN, MWIN, MWIP, MWPP, ESTG, EMHV, EPHV,
ESHV, ENLG, DPST, LCUF
When control via RS-232C is locked (see page 37)
E C D K O L Return code
(0DH, 0AH)
When RS-232C/LAN SELECT is set to LAN
U N S E L E C T E D
Return code
(0DH, 0AH)
nCommunication interval
• After OK or ERR is returned, you must send the following
commands.
To set a timeout for the command response, specify 10
seconds or longer.
When connecting multiple monitors in a daisy chain, set the
timeout to at least the product of the monitor’s position from
the computer multiplied by 10 seconds.
Example) third monitor from computer: 30 seconds or longer.
• Provide an interval of 100 ms or more between the
command response and the transmission of the next
command.
VOLM0020
OK
INPS0001
WAIT
OK
Interval of 100 ms or more
TIPS
• When executing ALL RESET, set the timeout period to 30
seconds or longer.
• When turning the power on while the POWER ON DELAY
function is in use, set the timeout period to the POWER ON
DELAY period + 10 seconds or longer.
Advanced operation
This section explains commands for daisy chain connection.
The basic communication procedure is the same as in the
“One-to-one connection with a computer” section.
nID numbers
You can assign a unique ID number to each monitor (see
page 29). This allows you to control a particular monitor in a
daisy chain of monitors.
You can assign ID numbers either from the menu screen or
from the computer using RS-232 cable.
[E
xamp
l
e
]
ID number: 1 ID number: 2 ID number: 3 ID number:
4
If monitors are connected as shown above, you can
execute commands like “Set the volume of the monitor with
ID 4 to 20”.
When designating ID numbers for a set of monitors linked in a
daisy chain, you should basically avoid any duplication of ID
numbers.
ID numbers do not have to be assigned in ascending order
starting from the computer. They can also be connected as
shown below.
[E
xamp
l
e
]
ID number: 3 ID number: 2 ID number: 4 ID number:
1
40
E
Controlling the Monitor with a computer (RS-232C)
nCommands for ID control
The command examples shown on this page assume the
following connection and ID number set up.
ID number: 1 ID number: 2 ID number: 3 ID number: 4
IDST ......... A monitor receiving this command sets its own ID
number in the parameter eld.
Example:
IDST0001
OK 001 ←The ID number of this monitor is set to 1.
TIPS
You can automatically assign ID numbers by using the IDST
command with the Repeater control (see “Repeater control”
on page 41).
For example, using the command “IDST001+” automatically
sets the ID numbers, as shown below.
[E
xamp
l
e
]
ID number: 1 ID number: 2 ID number: 3 ID number:
4
IDST001 + ← ID setting command with repeater control
WAIT
OK 001 ←“OK” response from ID number: 1
OK 002 ←“OK” response from ID number: 2
OK 003 ←“OK” response from ID number: 3
OK 004 ←“OK” response from ID number: 4 (End)
IDSL ........The parameter of this command sets the ID number
of the monitor. The monitor is subject to the next
command.
Example:
IDSL0002 ←
The next command is for the monitor
with ID number: 2.
WAIT ←Searching for monitor with ID number:
2
OK 002 ←
Found monitor with ID number: 2
VOLM0030 ←Sets volume of monitor with ID
number: 2 to 30.
WAIT ←Processing
OK 002 ←OK response from monitor with ID
number: 2
VOLM0020 ←Sets volume to 20.
OK 001 ←The volume of the monitor with ID
number: 1 (the one directly connected
to the computer) is set to 20.*
* The IDSL command is effective only once, for the
immediately succeeding command.
IDLK ........
The parameter of this command sets the ID
number of the monitor. The monitor is subject to all
subsequent commands.
Example:
IDLK0002 ←
Following commands are for the monitor
with ID number: 2.
WAIT ←Searching for monitor with ID number:
2
OK 002 ←
Found monitor with ID number: 2
VOLM0030 ←Sets volume of monitor with ID
number: 2 to 30.*
WAIT ←Processing
OK 002
VOLM0020 ←Sets volume of monitor with ID
number: 2 to 20.*
WAIT
OK 002
IDLK0000 ←Canceling xed ID number setting
WAIT ←Canceling IDLK
OK 002 ←Cancelation complete
VOLM0010
OK 001 ←
The volume of the monitor with ID number:
1 (the one directly connected to the
computer) is set to 10. (IDLK is canceled.)
* The IDLK command remains effective until it is
canceled, or power is shut off.
IDCK ........Provides screen display of the ID number currently
assigned to a monitor, and the ID number currently
set for IDLK (if any).
Example:
(After executing IDLK0002)
IDCK0000 ←(Parameter has no meaning.)
ID : 001 IDLK : 002 ←Returned response. The ID
number is also displayed on the
monitor screen.
IDCK000 + ←Repeater control. (If a command
is used with repeater control, ID
designation using IDSL or IDLK
is canceled.)
WAIT
ID : 001 IDLK : 000
ID : 002 IDLK : 000
ID : 003 IDLK : 000
ID : 004 IDLK : 000
41 E
Controlling the Monitor with a computer (RS-232C)
nRepeater control
This system has a function to allow setting of multiple
monitors connected in a daisy chain using a single command.
This function is called repeater control. You can use Repeater
control function without assigning ID numbers.
[E
xamp
l
e
]
Set 1
Set 2 Set
3S
et 4
* If monitors are connected as shown above, you can
execute a command like “Set all monitors’ input settings to
D-SUB[RGB]”.
nRepeater control command
Repeater control is achieved by setting the FOURTH
CHARACTER of the parameter to “+”.
Example:
VOLM030 + ← Sets volume of all monitors to 30.
In repeater control, responses are returned by all the
connected monitors.
If you want to determine that a value has been returned by a
specic set, assign ID numbers to each monitor in advance.
When some monitors do not return their responses, the
probable cause is that the monitors could not receive the
command or command processing is not complete. Do not
send a new command.
Example: (When 4 monitors are connected, and
assigned ID numbers: 1 through 4)
VOLM030 +
WAIT
OK 001
OK 002
OK 003
OK 004 ←If 4 monitors are connected in
a chain, reliable operation can
be ensured by sending a new
command only after a reply
has been returned by 4th (last)
monitor.
Repeater control can also be used for reading settings.
Example:
VOLM ? ? ? +
WAIT
10 001
Volume settings for all
monitors are returned.
20 002
30 003
30 004
TIPS
• If repeater control is used during ID designation (IDSL,
IDLK), the ID designation is canceled.
Setting of the GAMMA user data
nTo transfer the GAMMA user data
Use the user data transfer commands (UGRW, UGGW and
UGBW). For each of the R, G and B colors, divide the total
512 pieces of user data into 16 blocks, and transfer 32 pieces
of data with each command.
C1 C2 C3 C4 P1 P2 P3 P4
…
S1 S2
Command field
Block number (01 to 16)
Data fieldChecksum field
Example: To transfer the data of block 1 (0 to 31 levels)
of red (R) data
UGRW01000000010002 … 0031C0
Command
Block number
32 pieces of data Checksum
One piece of data consists
of 4 digits.
* If data is less than 4 digits, add a “0” (zero) to make it 4
digits.
* The checksum eld is the character string (ASCII) data of
lower-order one byte which indicates the sum of the block
number and 32 pieces of data in hexadecimal (0 to F).
nSaving the GAMMA user data
Use the user data save command (UGSV) to save the
transferred user data in the monitor.
If the data is not saved, it will be cleared when:
• The main power switch is off.
• POWER SAVE MODE is ON and the monitor enters
standby mode.
nActivating the GAMMA user data
To activate the transferred user data, select USER for GAMMA
of the PICTURE menu, or send the corresponding RS-232C
command.
nChecking the GAMMA user data
Use the user data read commands (UGRR, UGGR and
UGBR) to return 512 pieces of user data for each of the R,
G and B colors. Divide the data into 16 blocks and return 32
pieces of data with each command. The value to be returned
is not the value stored in the monitor, but the value in the
temporary memory for display. (These values are the same
when the user data save command (UGSV) above has been
sent.)
TIPS
• The user data is not initialized by RESET of the PICTURE
menu. To initialize the user data, use ALL RESET of the
FUNCTION menu.
The GAMMA user data initialize command (UGRS) allows
the initialization of the user data only.
42
E
RS-232C command table
How to read the command table
Command: Command eld (See page 38.)
Direction: W When the “Parameter” is set in the parameter eld (see page 38), the command functions as described
under “Control/Response Contents”.
R The returned value indicated under “Reply” can be obtained by setting “????”, “ ?” or “???+”
(repeater control) in the parameter eld. (See page 38.)
Parameter: Parameter eld (See page 38.)
Reply: Response (Returned value)
* : When POWER SAVE MODE is set to OFF:
“●/○” : Indicates a command which can be used in standby mode or when the power is on.
“–” : Indicates a command which can be used when the power is on. Cannot be used in standby mode.
When POWER SAVE MODE is set to ON:
“●” : Indicates a command which can be used in standby mode or when the power is on.
“○/–” : Indicates a command which can be used when the power is on. Cannot be used in standby mode.
Power control/Input mode selection
Function
Command Direction
Parameter Reply Control/Response contents *
POWER CONTROL POWR W 0 Switches to standby mode.
●
1 Returns from standby mode.
R 0 Standby mode
1 Normal mode
2 Input signal waiting mode
INPUT MODE SELECTION INPS W 0 Toggle change for input mode. Terminals not selected in INPUT SELECT
cannot be selected.
1 DVI-D
2 D-SUB[RGB]
“ERR” when other than RGB is selected for D-SUB of INPUT SELECT.
3 D-SUB[COMPONENT]
“ERR” when other than COMPONENT is selected for D-SUB of INPUT
SELECT.
10 HDMI1
13 HDMI2
14 DisplayPort
21 OPTION
“ERR” when nothing is attached in the expansion slot.
R 1 DVI-D
2 D-SUB[RGB]
3 D-SUB[COMPONENT]
10 HDMI1
13 HDMI2
14 DisplayPort
21 OPTION
Controlling the Monitor with a computer (RS-232C)
43 E
SCREEN menu
Function
Command Direction
Parameter Reply Control/Response contents *
AUTO ASNC W 1 When the input mode is D-SUB[RGB].
-
CLOCK CLCK WR 0-1200 0-1200 When the input mode is D-SUB[RGB].
Varies depending on the signal.
PHASE PHSE WR 0-63 0-63 When the input mode is D-SUB[RGB].
POSITIONING POSITION OF THE
LONGEST DIRECTION
HPOS WR 0-100 0-100 0-800 on D-SUB[RGB].
Varies depending on the signal.
POSITION OF
THE SHORTEST
DIRECTION
VPOS WR 0-100 0-100 0-200 on D-SUB[RGB].
Varies depending on the signal.
SIZE SIZE OF THE
LONGEST DIRECTION
HSIZ WR 0-100 0-100
SIZE OF THE
SHORTEST
DIRECTION
VSIZ WR 0-100 0-100
SIZE (SCREEN SIZE) WIDE WR 1-5 1-5 1: WIDE, 2: NORMAL, 3: Dot by Dot, 4: ZOOM1, 5: ZOOM2 ○
RESOLUTION
SETTING
LONGEST DIRECTION
RESOLUTION
HRES WR 300-1920 300-1920 When the input mode is D-SUB[RGB].
Only even numbers are valid for parameters.
Varies depending on the signal.
-
SHORTEST
DIRECTION
RESOLUTION
VRES WR 200-1200 200-1200
INPUT SIGNAL (D-SUB[RGB]) PXSL WR 1 1 768) 1360 x 768
2 2 768) 1280 x 768
3 3 768) 1024 x 768
5 5 480) 848 x 480
6 6 480) 640 x 480
7 7 1050) 1680 x 1050
8 8 1050) 1400 x 1050
9 9 768) AUTO
10 10 480) AUTO
Check the resolution
(other than D-SUB[COMPONENT])
PXCK R - Returns current resolution in the form of hhh, vvv.
Check the resolution
(HDMI1, HDMI2, D-SUB[COMPONENT], OPTION
(When you have used the expansion slot to expand
the functions.))
RESO R - 480i, 480p, 1080i, 720p, 1080p, VGA , etc.
ZOOM2 SPECIAL SETTING
(D-SUB[RGB])
Z2SP WR 0-1 0-1 0: OFF, 1: ON ○
RESET ARST W 1 -
Controlling the Monitor with a computer (RS-232C)
44
E
PICTURE menu
Function
Command Direction
Parameter Reply Control/Response contents *
BRIGHT VLMP WR 0-31 0-31
○
CONTRAST CONT WR 0-60 0-60
BLACK LEVEL BLVL WR 0-60 0-60
TINT TINT WR 0-60 0-60
COLORS COLR WR 0-60 0-60
SHARPNESS SHRP WR 0-24 0-24
COLOR
ADJUSTMENT
COLOR MODE BMOD WR 0 0 STD
2 2 VIVID
3 3 sRGB (sRGB cannot be used when input mode is D-SUB[COMPONENT].)
4 4 HIGH ILLUMINANCE
WHITE BALANCE WHBL WR 0-3 0-3 0:THRU, 1:PRESET, 2:USER, 3:ADJUST UNIFORMITY
PRESET CTMP WR 1-28 1-28
From 1: approximately 3,000K to 15: approximately 10,000K (500K steps)
16: approximately 5,600K, 17: approximately 9,300K, 18: approximately 3,200K
From 19: approximately 10,500K to 28: approximately 15,000K (500K steps)
“ERR” when WHBL is not set to 1.
USER R-CONTRAST CRTR WR 0-256 0-256 “ERR” when WHBL is not set to 2.
G-CONTRAST CRTG WR 0-256 0-256
B-CONTRAST CRTB WR 0-256 0-256
R-OFFSET OFSR WR -127-127 -127-127
G-OFFSET OFSG WR -127-127 -127-127
B-OFFSET OFSB WR -127-127 -127-127
ADJUST
UNIFORMITY
R-CONTRAST CRTR WR 0-256 0-256 “ERR” when WHBL is not set to 3.
G-CONTRAST CRTG WR 0-256 0-256
B-CONTRAST CRTB WR 0-256 0-256
R-OFFSET OFSR WR -127-127 -127-127
G-OFFSET OFSG WR -127-127 -127-127
B-OFFSET OFSB WR -127-127 -127-127
BRIGHTNESS
VALUE
BCLB WR 0-255 0-255
COPY TO USER CPTU W 0 Copies a preset value to the user setting.
GAMMA GAMM WR 0-9 0-9
0: 1.8, 1: 2.2, 2: 2.4, 3: DICOM SIMULATION, 4:USER, 5:2.0, 6:STD, 7:LIGHT 2,
8:LIGHT 1, 9:DARK
FLESH TONE FLES WR 0-2 0-2 0: OFF, 1: LOW, 2: HIGH
C.M.S.-HUE CMHR WR -10-10 -10-10 R
CMHY Y
CMHG G
CMHC C
CMHB B
CMHM M
CRST W 1 Resets the hue.
C.M.S.-SATURATION CMSR WR -10-10 -10-10 R
CMSY Y
CMSG G
CMSC C
CMSB B
CMSM M
CRST W 2 Resets the saturation.
Controlling the Monitor with a computer (RS-232C)
45 E
Function
Command Direction
Parameter Reply Control/Response contents *
ADVANCED AUTO AGIN W 1 When the input mode is D-SUB[RGB]. -
ANALOG GAIN ANGA WR 0-127 0-127 When the input mode is D-SUB[RGB].
○
ANALOG OFFSET ANOF WR 0-127 0-127 When the input mode is D-SUB[RGB].
NR TDNR WR 0-2 0-2 0: OFF, 1: LOW, 2: HIGH
RGB INPUT RANGE INPR WR 0-2 0-2 0: AUTO, 1: FULL, 2: LIMITED
“ERR” when the input mode is D-SUB[COMPONENT].
When the input mode is DVI-D, or D-SUB[RGB] the value 0 is invalid.
DISPLAY COLOR PATTERN PTDF WR 0 0 No pattern display.
-
1 1 White single color pattern display.
2 2 Red single color pattern display.
3 3 Green single color pattern display.
4 4 Blue single color pattern display.
99 99 Red/green/blue mixed color pattern display.
Set each color's level with PTDR, PTDG, PTDB.
DISPLAY COLOR PATTERN
(R)
PTDR WR 0-255 0-255 Set the R, G, and B levels of the mixed color pattern.
“ERR” when PTDF is not set to 99.
DISPLAY COLOR PATTERN
(G)
PTDG WR 0-255 0-255
DISPLAY COLOR PATTERN
(B)
PTDB WR 0-255 0-255
DISPLAY COLOR PATTERN
(LEVEL)
PTDL WR 0-255 0-255 Set the white, red, green, and blue levels of the single color pattern.
“ERR” when the DISPLAY COLOR PATTERN is set to a color other than
white, red, green, or blue.
UNIFORMITY LCUF WR 0-3 0-3 0: OFF, 1: MODE1, 2: MODE2, 3: MODE3 ○
RESET ARST W 2 -
SETUP menu
Function
Command Direction
Parameter Reply Control/Response contents *
DATE/TIME SETTING DATE WR
AABBCCDDEE AABBCCDDEE
AA: Year, BB: Month, CC: Day, DD: Hour, EE: Minute
○
DATE FORMAT DTFT WR
0-2 0-2
0: YYYY/MM/DD, 1: MM/DD/YYYY, 2: DD/MM/YYYY
YYYY: Year, MM: Month, DD: Day
TIME FORMAT TMFT WR
0-1 0-1
0: 24-HOUR TIME, 1: 12-HOUR TIME
SCHEDULE SC01-
SC08
WR
ABCDEFFGGH ABCDEFFGGH
Schedule of a specied number
A: Schedule 0= Not effective, 1 = Effective
B: Power 0 = OFF, 1 = ON
C: Day of the week 1 0 = Only once, 1 = Every week, 2 = Every day
D: Day of the week 2 0 = Sunday, 1 = Monday through 6 = Saturday,
9 = Not exist
E: Day of the week 3 0 = Sunday, 1 = Monday through 6 = Saturday,
9 = Not exist
F: Hour 00-23
G: Minute 00-59
H: Input 0 = Not specied, 1=HDMI1, 2=HDMI2, 4=D-SUB,
6=DisplayPort, 7=DVI-D, 8=OPTION(valid when an
option is attached)
SCHEDULE BRIGHTNESS SB01-
SB08
WR 0-31 0-31 Screen brightness to change
99 99 Disable brightness setting
LANGUAGE LANG WR 14 14 ENGLISH
1 1 DEUTSCH
2 2 FRANÇAIS
3 3 ITALIANO
4 4 ESPAÑOL
5 5 РУССКИЙ
6 6
7 7
INPUT SELECT D-SUB SLDS WR 0-1 0-1 0:RGB, 1:COMPONENT
HDMI CEC LINK
CELK WR 0-1 0-1 0: OFF, 1: AUTO
AUTO POWER ON
ATPO WR 0-1 0-1 0: OFF, 1: ON
HDMI AUTO VIEW
(HDMI1)
HDAW WR 0-1 0-1 0: OFF, 1: ON
HDMI AUTO VIEW
(HDMI2)
H2AW WR 0-1 0-1 0: OFF, 1: ON
HDMI AUTO VIEW
(
OPTION
)
OPAW WR 0-1 0-1 0: OFF, 1: ON
(valid when you have used the expansion slot to expand the functions)
HOT PLUG CONTROL
(DVI-D)
HPCT WR 0-1 0-1 0: OFF, 1: ON
HOT PLUG CONTROL
(HDMI1)
HPCH WR 0-1 0-1 0: OFF, 1: ON
HOT PLUG CONTROL
(HDMI2)
HPH2 WR 0-1 0-1 0: OFF, 1: ON
HOT PLUG
CONTROL (OPTION)
HPOP WR 0-1 0-1 0: OFF, 1: ON
(valid when you have used the expansion slot to expand the functions)
DisplayPort STREAM DPST WR 0-1 0-1 0: SST, 1: MST
“ERR” when PIP MODES is a value other than OFF. -
Controlling the Monitor with a computer (RS-232C)
46
E
Controlling the Monitor with a computer (RS-232C)
Function
Command Direction
Parameter Reply Control/Response contents *
DisplayPort SETTING HIGH-FREQUENCY
GAIN
DPHG WR 0-31 0-31
-
LOW-FREQUENCY
GAIN
DPLG WR 0-31 0-31
FILTER SETTING DPFL WR 0-15 0-15
OFFSET DPOF WR 0-15 0-15
RESET DPRS W 1
AUDIO SELECT HDMI1 ASHP WR 0-1 0-1 0: HDMI, 1: AUDIO
○
HDMI2 AH2P WR 0-1 0-1 0: HDMI, 1: AUDIO
DisplayPort
ASDI WR 1, 3 1, 3 1: AUDIO, 3: DisplayPort
OPTION ASOP WR 0-1 0-1 0: OPTION, 1: AUDIO
(valid when you have used the expansion slot to expand the functions)
AUDIO OUTPUT AOUT WR 0-1 0-1 0: VARIABLE, 1: FIXED
START INPUT MODE SUIM WR 1-4, 6-7, 10 1-4, 6-7, 10 1: LAST INPUT MODE, 2: DisplayPort, 3: HDMI1, 4: HDMI2, 6: DVI-D, 7: D-SUB,
10: OPTION
(valid when you have used the expansion slot to expand the functions)
COMMUNICATION
SETTING
RS-232C/LAN
SELECT
CTLS WR 0-1 0-1 0: RS-232C, 1: LAN ●
BAUD RATE BAUD WR 0-2 0-2 0: 9600bps, 1: 19200bps, 2: 38400bps
○
Crestron Connected CRCN WR 0-1 0-1 0: OFF, 1: ON
ID SETTING ID No.SET IDST W 0-255 Sets the monitor’s ID number. (“0” means “no ID number”.)
R 0-255 Returns the monitor’s ID number.
ID NO. SETTING
(ONCE)
IDSL W 1-255 Set a monitor’s ID number to send a command.
This ID number is only effective for the command immediately after this command.
0 Clears the ID number if one has been designated.
ID NO. SETTING
(SUBSEQUENT)
IDLK W 1-255 Set a monitor’s ID number to send a command.
This ID number is effective for the next and all subsequent commands after this
command.
0 Clears the ID number if one has been designated.
ID CHECK IDCK W 0 ID : xxx
IDLK : yyy
Displays monitor’s own ID number and the selected ID number on the screen.
ID DISPLAY IDDP W 0-2 0: OFF, 1: ON, 2: ON (turns OFF after 4 sec.)
(The IP address and MAC address are both displayed.) -
REMOTE No. RCNO WR 0-9 0-9 Sets the number of the remote control unit.
○
COPY SETTING
VALUE
COPY TO ID No. CPMD WR 0 0 Copy to all monitors.
1-255 1-255 Copy to the monitor with the set ID number.
COPY SETTING
VALUE TARGET
CPTG WR 0 0 Copies the PICTURE menu settings.
1 1 Copies all the settings.
47 E
MONITOR menu
Function
Command Direction
Parameter Reply Control/Response contents *
PORTRAIT/LANDSCAPE INSTALL STDR WR 0-1 0-1 0: LANDSCAPE, 1: PORTRAIT
○
ROTATE 180°/PICTURE FLIP PFIL WR 0, 2, 3 0, 2, 3 0: ROTATE 180° is set to OFF. PICTURE FLIP is set to OFF.
2: ROTATE 180° is set to OFF. PICTURE FLIP is set to ON.
3: ROTATE 180° is set to ON. PICTURE FLIP is set to OFF.
“ERR” when PIP MODES is a value other than OFF.
When INVERSE SCAN is set to ON, can not set to 3 “ERR”.
When INVERSE SCAN is set to OFF, can not set to 2 “ERR”.
INVERSE SCAN INVV WR 0-1 0-1 0: OFF, 1: ON
OSD H-POSITION OSDH WR 0-100 0-100 “ERR” when PORTRAIT/LANDSCAPE INSTALL is set to PORTRAIT.
OSD V-POSITION OSDV WR 0-100 0-100
OPERATION MODE FNCM WR 0-1 0-1 0: MODE1, 1: MODE2
POWER SAVE MODE STBM WR 0-1 0-1 0: OFF, 1: ON
OFF IF NO OPERATION
ATOF WR 0-1 0-1 0: OFF, 1: ON
TIME AOFT WR 1-12 1-12 1-12: 1-12 hours
POWER ON DELAY PODS WR 0-1 0-1 0: OFF, 1: ON
INTERVAL PWOD WR 1-60 1-60 1-60: 1-60 seconds
SELF ADJUST AADJ WR 0-1 0-1 0: OFF, 1: ON
START TIMING AADD WR 10-200 10-200 10: 1 second through 200: 20 seconds
Controlling the Monitor with a computer (RS-232C)
48
E
MULTI/PIP menu
Function
Command Direction
Parameter Reply Control/Response contents *
ENLARGE ENLG WR 0-1 0-1 0: OFF, 1: ON
○
ENLARGE MODE EMAG WR 1-4 1-4 1: 2 x 2, 2: 3 x 3, 3: 4 x 4, 4: 5 x 5
EMHV WR 12(21)-55 12(21)-55 1 x 2 (2 x 1) to 5 x 5 (“m x n” is expressed as “mn”, where m and n are the
numbers of monitors specied for the longest direction and the shortest direction
respectively.)
IMAGE POSITION (M x N) EPHV WR 11-55 11-55 Species values in the order of IMAGE POSITION IN LONGEST/ SHORTEST
DIRECTION.
IMAGE POSITION (2 x 2) EPOS WR 0-3 0-3 See the description below.
IMAGE POSITION (3 x 3) EPOS WR 0-8 0-8
IMAGE POSITION (4 x 4) EPOS WR 0-15 0-15
IMAGE POSITION (5 x 5) EPOS WR 0-24 0-24
ENLARGED
SCREEN
POSITIONING
THE LONGEST
DIRECTION
EPSH WR -999-999 -999-999 The setting range depends on the ENLARGE MODE setting and the IMAGE
POSITION.
THE SHORTEST
DIRECTION
EPSV WR -999-999 -999-999
BEZEL ADJUST BZCO WR 0-1 0-1 0: OFF, 1: ON
BEZEL ADJUST TOP BZCT WR 0-1 0-1 0: OFF, 1: ON
BOTTOM BZCB WR 0-1 0-1 0: OFF, 1: ON
RIGHT BZCR WR 0-1 0-1 0: OFF, 1: ON
LEFT BZCL WR 0-1 0-1 0: OFF, 1: ON
BEZEL WIDTH TOP BZWT WR 0-100 0-100
BOTTOM BZWB WR 0-100 0-100
RIGHT BZWR WR 0-100 0-100
LEFT BZWL WR 0-100 0-100
ENLARGE/IMAGE POSITION SETTING ESTG WR XXYY XXYY XX: ENLARGE MODE (Same as EMAG), YY: IMAGE POSITION (Same as
EPOS)
ESHV WR XXYY XXYY XX: ENLARGE MODE (Same as EMHV), YY: IMAGE POSITION (Same as
EPHV)
• IMAGE POSITION (EPOS) setting
In landscape orientation
1
3
0
2
012
345
678
2
6
10
3
7
11
01
45
89
12 13 14 15
0
5
10
15
20
1
6
11
16
21
2
7
12
17
22
3
8
13
18
23
4
9
14
19
24
2 x 2 3 x 3 4 x 4 5 x 5
In portrait orientation
2 x 2 3 x 3 4 x 4 5 x 5
1
3
02
0
1
2
4
5
6
8
9
10
3
7
11
12
13
14
15
0
1
2
5
6
7
10
11
12
3813
15
16
17
18
20
21
22
23
4
9141924
0
1
2
3
4
5
6
7
8
Controlling the Monitor with a computer (RS-232C)
49 E
Controlling the Monitor with a computer (RS-232C)
Function
Command Direction
Parameter Reply Control/Response contents *
PIP MODES MWIN WR 0-3 0-3 0: OFF, 1: PIP, 2: PbyP, 3: PbyP2
○
PIP SIZE MPSZ WR 1-64 1-64
PIP POS THE LONGEST
DIRECTION
MHPS W 0-100
R 0-100
THE SHORTEST
DIRECTION
MVPS W 0-100
R 0-100
PIP POS LD+SD BATCH MPOS W 0-100,0-100 Specify the position in MPOSxxxyyy format.
(xxx: Longer side, yyy: Shorter side position)
R 0-100,0-100 Returns a response in (xxx,yyy) format.
(xxx: Longer side, yyy: Shorter side position)
PIP BLEND MWBL WR 0-7 0-7
PIP SOURCE MWIP WR 1 1 DVI-D
2 2 D-SUB[RGB]
3 3 D-SUB[COMPONENT]
10 10 HDMI1
13 13 HDMI2
14 14 DisplayPort
21 21 OPTION (valid when you have used the expansion slot to expand the functions)
SOUND CHANGE MWAD WR 1-2 1-2 1: MAIN, 2: SUB
MAIN POS (Main screen) MWPP WR 0-1 0-1 0: POS1, 1: POS2
PbyP2 POS (Sub screen) MW2P WR 0-2 0-2 0: POS1, 1: POS2, 2: POS3
OTHERS menu
Function
Command Direction
Parameter Reply Control/Response contents *
SCREEN MOTION PATTERN SCSV WR 0-4 0-4 0: OFF, 1-4: PATTERN1-4
○
MOTION TIME1 MTIM WR 0-20 0-20
MOTION TIME2
(PATTERN1)
MINT WR 10-990 10-990 Per 10 seconds
MOTION TIME2
(PATTERN2-4)
MINT WR 5-20 5-20 Per second
POWER MANAGEMENT PMNG WR 0-1 0-1 0: OFF, 1: ON
CONNECT AUTO INPUT SELECT AICO WR 0-1 0-1 0: OFF, 1: ON
The input via the expansion slot is ignored.
NO SIGNAL AUTO INPUT SEL. AINO WR 0-1 0-1 0: OFF, 1: ON
AUTO INPUT
SELECT PRIORITY
DisplayPort APDP WR 0-10 0-10 0: Not selected by auto input selection, 1-10: Priority setting
“ERR” when OFF is selected for NO SIGNAL AUTO INPUT SEL..
APOP will result in an error (“ERR”) when an optional part that is not a target for
this function is connected.
All input terminals cannot be set to 0 simultaneously.
HDMI1 APH1
HDMI2 APH2
DVI-D APDV
D-SUB APD1
OPTION APOP
LOGO SCREEN BTSC WR 0-1 0-1 0: OFF, 1: ON
SCAN MODE
(HDMI1, HDMI2, D-SUB[COMPONENT],
OPTION (When you have used the expansion
slot to expand the functions.))
SCAN WR 0-2 0-2 0: MODE1, 1: MODE2, 2: MODE3
VOLUME VOLM WR 0-31 0-31
MUTE AUDIO MUTE WR 0-1 0-1 0: OFF, 1: ON -
INFORMATION MODEL INF1 R Value ●
SERIAL NO SRNO R Value
50
E
Controlling the Monitor with a computer (RS-232C)
Initialization/Functional Restriction Setting (FUNCTION) menu
Function
Command Direction
Parameter Reply Control/Response contents *
ALL RESET RSET W 0-1 0: ALL RESET 1, 1: ALL RESET 2 -
ADJUSTMENT LOCK ALCK WR 0-2 0-2 0: OFF, 1:ON1, 2:ON2 ●
ADJUSTMENT LOCK TARGET ALTG WR 0-2 0-2 0: REMOTE CONTROL, 1: MONITOR BUTTONS, 2: BOTH
○
OSD DISPLAY LOSD WR 0-2 0-2 0: ON1, 1: OFF, 2: ON2
LED OFLD WR 0-1 0-1 0: ON, 1: OFF
TEMPERATURE ALERT TALT WR 0-2 0-2 0: OFF, 1: OSD & LED, 2: LED
STATUS ALERT SALT WR 0-2 0-2 0: OFF, 1: OSD & LED, 2: LED
POWER BUTTON PBTN WR 0-1 0-1 0: MONITOR, 1: EXT. CONTROLLER
EXTERNAL CONTROLLER INPUT PCIP WR 0-4 0-4 0: D-SUB, 1: DisplayPort, 2: HDMI1, 3: HDMI2, 4: DVI-D
(“ERR” when MONITOR is selected for POWER BUTTON.)
SIGNAL RESPONSE LEVEL HDUC WR 1-200 1-200
Others
Function
Command Direction
Parameter Reply Control/Response contents *
TEMPERATURE SENSOR DSTA R 0 Internal temperature normal
●
1 Internal temperature abnormal has occurred and the monitor is in standby mode
2Internal temperature abnormal occurred (To delete the information of temperature
abnormal, turn off the main power.)
3 Internal temperature abnormal has occurred and backlight brightness is dimmed
4 Temperature sensor abnormal
TEMPERATURE ACQUISITION ERRT R Value Returns the temperature at the temperature sensors.
Indicates a temperature sensor abnormality when “126” is returned. ○
CAUSE OF LAST STANDBY MODE STCA W 0 Initialization
●
R 0 No detectable error has occurred
1 Standby mode by POWER button
2 Main power off by the main power switch
3 Standby mode by RS-232C or LAN
4 Input signal waiting mode by No Signal
6 Standby mode by abnormal temperature
8 Standby mode by SCHEDULE setting
9 Standby mode by DDC/CI
10 Standby mode by HDMI CEC
20 Standby mode by OFF IF NO OPERATION setting
Commands for setting of the GAMMA user data
Function
Command Direction
Parameter Reply Control/Response contents *
RED GAMMA DATA TRANSFER UGRW W aaxxxx ··· xxxxcc
(xxxx: 32 pieces)
aa: 01-16
xxxx: 0000-1023
cc: 00-FF
aa: Block number
xxxx: 32 pieces of user data
cc: Checksum (ASCII data) of the block number and user data
○
GREEN GAMMA DATA TRANSFER UGGW W
BLUE GAMMA DATA TRANSFER UGBW W
RED GAMMA DATA READ UGRR W 1-16 xxxx ··· xxxx
(xxxx: 32 pieces)
xxxx: 0000-1023
xxxx: User data of 32 pieces
GREEN GAMMA DATA READ UGGR W 1-16
BLUE GAMMA DATA READ UGBR W 1-16
USER DATA INITIALIZE UGRS W 0 Initialize the user data.
USER DATA SAVE UGSV W 0 Save the user data in the monitor.
51 E
Your monitor can be connected to a LAN allowing you to
control it from a computer on the LAN.
You can also congure the monitor to send e-mail notication
when it has a problem.
The connection requires a commercially available LAN cable
(UTP cable, Category 5, straight through).
LAN terminal
Hub
Network (LAN)
LAN cable (commercially available, straight)
TIPS
• You must assign an IP address to the monitor by following
the procedures in “Settings to connect to a LAN”. (See the
description on the right.)
• Your computer must be installed with the web browser.
• When POWER SAVE MODE is set to ON, control is not
possible in standby mode.
• To control the monitor via LAN, set RS-232C/LAN SELECT
to LAN. (See page 29.)
• You cannot use RS-232C and LAN control simultaneously.
Initializing personal information
• Personal information such as e-mail addresses can be
registered in the monitor. Before transferring or disposing of
the monitor, initialize all settings by selecting ALL RESET
1. (See page 37.) Note that ALL RESET 2 will not initialize
e-mail addresses and other settings.
Controlling the Monitor with a computer (LAN)
Settings to connect to a LAN
Set the monitor’s IP address and subnet mask to match the
settings of your LAN.
These settings can be made on either the monitor or a
computer connected to the monitor.
The settings depend on the conguration of your LAN. Ask
your LAN administrator for details.
nTo set on the monitor
Set RS-232C/LAN SELECT of COMMUNICATION SETTING
on the SETUP menu to LAN, and then set the LAN SETUP
options. (See page 29.)
After setting each item, select SET and press the ENTER button.
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to ON.
To set the address manually, set this to OFF.
IP ADDRESS
If the DHCP CLIENT is set to OFF, specify an IP address.
Press the or button to select items, and press the or
button to change the values.
SUBNET MASK
If the DHCP CLIENT is set to OFF, specify the subnet mask.
Press the or button to select items, and press the or
button to change the values.
DEFAULT GATEWAY
If the DHCP CLIENT is set to OFF, specify the default
gateway.
If you are not using a default gateway, specify “0.0.0.0”.
Press the or button to select items, and press the or
button to change the values.
RESET
Resets the values of the LAN settings to the factory preset
values.
Select ON and then press the ENTER button.
TIPS
• When the IP address is set manually, the IP addresses of
the monitor connected to the RS-232C output terminal and
the daisy chain of connected monitors that follows can be
assigned automatically. (See page 29.)
52
E
nTo set from a computer
When the monitor is connected to a computer, LAN settings
can be congured via computer.
Set up process
(1) Connect your monitor to a computer
(2) Specify the computer’s IP address
(3) Congure the monitor’s LAN settings
(1) Connecting your monitor to a computer
Connect a commercially available crossover LAN cable (UPT
cable, Category 5) to the LAN port on the computer and this
monitor.
Computer
LAN cable
(commercially available, crossover)
To LAN terminal
LAN terminal
(2) Specifying the computer’s IP address
To congure the monitor’s LAN settings, you must temporarily
change the settings on the computer.
This explanation is based on Windows 7.
1. Log on to the computer with an administrator account.
2. Click [Start], and then click “Control Panel”.
3. Click “View network status and tasks” in “Network and
Internet”.
In “Classic View”, click “Network and Sharing Center”.
4. Click “Local Area Connection” and then “Properties”.
5. Click “Internet Protocol Version 4 (TCP/IPv4)” and then
“Properties”.
6. Make a note of the current IP address, subnet mask, and
default gateway settings.
Make sure you write this information now as you will
be changing the IP address, subnet mask, and default
gateway settings back to these settings afterwards.
7. Temporarily change the IP address and subnet mask.
To access the monitor as it is shipped from the factory, set
as follows.
• IP Address :192.168.150.1
• Subnet Mask :255.255.255.0
• Default Gateway :(leave blank)
8. Click [OK] and then reboot the computer.
TIPS
• This monitor is factory preset as shown below.
(When DHCP CLIENT is set to OFF)
IP Address : 192.168.150.2
Subnet Mask : 255.255.255.0
Default Gateway : 0.0.0.0
(3) Conguring the monitor’s LAN settings
Access the monitor using the web browser.
Controlling the monitor
1. Turn the power ON to the monitor.
2. Set RS-232C/LAN SELECT of COMMUNICATION
SETTING on the SETUP menu to LAN.
3. Set DHCP CLIENT of LAN SETUP of COMMUNICATION
SETTING on the SETUP menu to OFF.
Computer operation
4. Launch the web browser, in the “Address” box type
“http://192.168.150.2/” and press the Enter key.
5. Enter the USER NAME and PASSWORD.
The following values are set in the initial settings.
USER NAME: admin, PASSWORD: admin
* To enable security on the monitor, change the user
name and password. (See page 55.)
Controlling the Monitor with a computer (LAN)
53 E
6. Click on “LAN SETUP” under NETWORK.
7. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc.
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to ON.
To set the address manually, set this to OFF.
IP ADDRESS
If the DHCP CLIENT is set to OFF, specify an IP address.
SUBNET MASK
If the DHCP CLIENT is set to OFF, specify the subnet mask.
DEFAULT GATEWAY
If the DHCP CLIENT is set to OFF, specify the default gateway.
If you are not using a default gateway, specify “0.0.0.0”.
8. When the setting is changed, click [Apply].
9. Check the message and click [OK].
10
. Exit the web browser.
11
. Restore the computer’s IP address jotted in Step 6, “(2)
Specifying the computer’s IP address”.
12
. Connect the monitor and the computer to the LAN.
Caution
• Wait 10 seconds after clicking [OK] before proceeding.
• When operating using the remote control unit or similar,
click [Refresh].
TIPS
• When the IP address is set manually, the IP addresses of
the monitor connected to the RS-232C output terminal and
the daisy chain of connected monitors that follows can be
assigned automatically. (See page 29.)
Controlling with a computer
nBasic operation
You use the web browser on a computer on the LAN to control
the monitor.
1. Launch the web browser on the computer.
2.
In the “Address” box, type “http://” followed by your monitor’s
IP address followed by “/”, then press the Enter key.
You can conrm the IP address with the INFORMATION
function.
When prompted to enter a USER NAME and PASSWORD,
type the user name and password that you specied in the
SECURITY settings (see page 55), and click [OK].
The following values are set in the initial settings.
USER NAME: admin, PASSWORD: admin
* To enable security on the monitor, change the user
name and password. (See page 55.)
3. You can check, control, and change the monitor’s status
and settings by clicking the menu items on the left side of
the screen.
• If you see an [Apply] button next to a setting, click it after
you change that setting.
TIPS
• See pages 54 to 58 for details on each setting.
• If you click [Refresh] before the screen nishes updating
the current display, the “Server Busy Error” will appear.
Wait for a moment before operating your monitor again.
• You cannot operate the monitor while it is warming up.
• If DHCP CLIENT is set to ON, check the monitor’s IP
address in INFORMATION2. (See page 21.)
Controlling the Monitor with a computer (LAN)
54
E
nINFORMATION
Information about this monitor appears.
nCONTROL
You can control the operations corresponding to the POWER
button, INPUT button, etc. on the remote control unit. (See
page 20.)
TIPS
• In standby mode, only Power ON operation is available.
nADJUSTMENT
You can adjust these settings which are also available on the
monitor’s menu.
• SCREEN (See page 25.)
• PICTURE (See pages 26 to 27.)
• PICTURE (ADVANCED) (See page 27.)
• SETUP (See pages 28 to 29.)
• MONITOR (See page 30.)
• OTHERS (See page 32.)
• SCHEDULE (See page 35.)
• MULTI (See page 31.)
• PIP/PbyP (See page 31.)
• FUNCTION (See page 37.)
TIPS
• After changing DISPLAY COLOR PATTERN to OFF, click
[Refresh] to correctly retrieve the status of the monitor.
Controlling the Monitor with a computer (LAN)
55 E
nNETWORK (LAN SETUP)
This screen allows you to set the settings necessary when the
monitor is connected to a LAN.
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to ON.
To set the address manually, set this to OFF.
IP ADDRESS
If the DHCP CLIENT is set to OFF, specify an IP address.
SUBNET MASK
If the DHCP CLIENT is set to OFF, specify the subnet mask.
DEFAULT GATEWAY
If the DHCP CLIENT is set to OFF, specify the default
gateway.
If you are not using a default gateway, specify “0.0.0.0”.
DNS SERVER ADDRESS AUTO ACQUISITION
If the DHCP CLIENT is set to ON, specify whether or not to
automatically obtain the DNS server address.
DNS SERVER
Specify the DNS server address if the DHCP CLIENT
is SET to OFF or the DNS SERVER ADDRESS AUTO
ACQUISITION is set to OFF.
If you are not using a DNS server, specify “0.0.0.0”.
RESET
Clicking [Execute] returns all of the LAN SETUP settings
to the factory-preset values except for the DNS SERVER
ADDRESS AUTO ACQUISITION and DNS SERVER
settings.
TIPS
• When the IP address is set manually, the IP addresses of
the monitor connected to the RS-232C output terminal and
the daisy chain of connected monitors that follows can be
assigned automatically. (See page 29.)
nNETWORK (SECURITY)
This screen allows you to specify the security-related settings.
USER NAME / PASSWORD
Sets up a user name and password to restrict access to this
monitor.
The following values are set in the initial settings.
USER NAME: admin, PASSWORD: admin
* To enable security on the monitor, change the user name
and password.
After entering a user name and password, click [Apply].
USE FOR Telnet CONNECTION
Sets whether to use a user name and password when
connecting over TELNET.
ACCEPT IP ADDRESS
You can limit access to this monitor by registering IP
addresses of computer’s that should have access.
To limit access, specify the option “From only specic IP
addresses”. Otherwise, to allow access from any computer,
specify “All IP Addresses”.
IP ADDRESS 1 to 3
If “ACCEPT IP ADDRESS” is set to “From only specic IP
addresses”, enter the IP addresses that you want to allow.
TIPS
• The USER NAME and PASSWORD can be up to 8
alphanumeric characters (hyphens and underscores
allowed).
• To cancel the user name and/or password after it has been
set, make the box empty and click [Apply].
Controlling the Monitor with a computer (LAN)
56
E
nNETWORK (GENERAL)
This screen allows you to specify the general LAN settings.
MONITOR NAME
Specify a name for this monitor as it should appear on the
web browser screen.
AUTO LOGOUT TIME
Specify the time (in minutes) to elapse before automatically
disconnecting this monitor from the network.
Specify in minutes from 1 to 65535. A value of ‘0’ will disable
this function.
DATA PORT
Specify the TCP port number to use for exchanging data with
the monitor.
Specify a value from 1025 to 65535.
SEARCH PORT
Specify the port number to use when searching for this
monitor.
Specify a value from 1025 to 65535.
INSTALLATION INFORMATION (NAME/LOCATION)
Specify the information to display for this monitor in the web
browser window.
LINK MODE
Selects the link speed and duplex.
Use AUTO normally.
TIPS
• The MONITOR NAME can be up to 16 alphanumeric
characters or symbols.
• Enter up to 50 characters in the NAME eld in the
INSTALLATION INFORMATION.
• Enter up to 100 characters in the LOCATION eld in the
INSTALLATION INFORMATION.
nMAIL (ORIGINATOR)
This screen allows you to congure the e-mail sent periodically
or when the monitor has an error.
The settings depend on the conguration of your LAN. Ask
your LAN administrator for details.
SMTP SERVER
Specify the SMTP server address for sending e-mail.
* When using a domain name, make sure to specify the
DNS SERVER as well. (See page 55.)
SMTP PORT
If the “AUTHENTICATION” is “SMTP-AUTH”, specify the port
number.
ORIGINATOR E-MAIL ADDRESS
Specify the e-mail address for this monitor.
This address becomes the e-mail address of the originator.
ORIGINATOR NAME
Specify the name for the originator.
This name appears in the “Originator Name” eld of the
e-mail.
AUTHENTICATION
Specify the authentication method to use when sending
e-mail.
POP SERVER
If the “AUTHENTICATION” is “POP before SMTP”, specify
the POP server address.
ACCOUNT NAME / PASSWORD
If the “AUTHENTICATION” is “POP before SMTP” or
“SMTP-AUTH”, specify the account name and password to
connect to the SMTP server.
TIPS
• You can enter up to 64 alphanumeric characters or symbols
for the ORIGINATOR E-MAIL ADDRESS, ORIGINATOR
NAME, ACCOUNT NAME, and PASSWORD.
• The SMTP SERVER and POP SERVER can be up to 64
characters.
The following characters can be used: a-z, A-Z, 0-9, - , .
Controlling the Monitor with a computer (LAN)
57 E
nMAIL (RECIPIENT)
This screen allows you to specify the recipients of the e-mail
sent periodically or when the monitor has an error.
RECIPIENT E-MAIL ADDRESSES
Specify the e-mail addresses to send error notication e-mail
to.
CONDITION
Specify the conditions to send mails.
When you check PERIODICAL, specify the date and time to
send the mails in the PERIODICAL setting.
CONFIRMATION
Sends test e-mail.
This allows you to conrm that the e-mail settings are
congured properly.
Attach the log le to a TEMPERATURE/HARDWARE error
e-mail.
When this option is checked, a log is added to the mail which
noties a temperature or status error.
E-MAIL TRANSMISSION ERROR REPORT
A report of the latest e-mail transmission errors will be
displayed.
The error report will be displayed when an e-mail
transmission error occurs.
Also, the e-mail transmission errors will be cleared when ALL
RESET 1 is executed. (See page 37.)
TIPS
• The RECIPIENT E-MAIL ADDRESSES can be up to 64
alphanumeric characters or symbols.
Controlling the Monitor with a computer (LAN)
nMAIL (PERIODICAL)
When PERIODICAL for CONDITION of MAIL (RECIPIENT) is
checked, set the date and time to send the mail.
DAY OF THE WEEK
Specify the day of the week to send the periodical mails.
TIME
Specify the time of the day to send the periodical mails.
Caution
• Do not turn off the main power when you set to send the
periodical mails.
• Specify the correct date and time. (See page 28.)
If the date and time settings are incorrect, the periodical
mail is not sent properly.
• Regularly conrm that the specied date and time is
correct.
58
E
Controlling the Monitor with a computer (LAN)
nSNMP
You can congure settings related to SNMP.
SNMP SETTING
Set whether to enable or disable SNMP.
VERSION
Set the version of the SNMP to be supported.
COMMUNITY NAME 1 to 3
Set the name of the community required for the access.
USER 1 to 3
Set the user name, password, authentication method and
other options required for access.
TRAP SETTING
Set whether to enable or disable the trap function.
When this function is enabled, a trap will be sent when the
monitor is turned on.
TRAP SETTING OF AUTHENTICATION ERROR
Set whether the trap function sends a notication when
authentication fails.
TRAP ADDRESS & PORT
Set the destination address and port number of the
notication sent by the trap function.
Caution
• After you set SNMP, click [Switch the main power of
monitor off and on now.] or turn off the monitor and then
turn it on again with the main power switch. When the
monitor restarts, wait about 30 seconds and then start the
next operation.
• If the IP address is changed while the SNMP function is
operational, turn off the monitor and then turn it on again
with the main power switch.
TIPS
• Depending on the SNMP settings, a short delay may occur
before the SNMP is usable. (About 5 minutes)
• Up to 16 alphanumeric letters and symbols can be used for
the community name, user name and password.
n SERVICE & SUPPORT
(URL INFORMATION)
You can display a specic URL in the URL INFORMATION
eld on the INFORMATION screen when an error occurs in
the monitor. (See page 54.)
URL INFORMATION
Enter the URL to display on the INFORMATION screen when
an error occurs on the monitor.
Up to 64 alphanumeric characters or symbols can be used.
CONDITION
Specify the condition to display the URL.
CONFIRMATION
The home page of the specied URL is displayed.
You can check whether the URL you entered is correct.
TIPS
• It is also possible to specify the message text, such as the
name of a contact or a telephone number, to be displayed
instead of the linked URL.
59 E
Controlling the Monitor with a computer (LAN)
nCrestron Connected
Display the Crestron Connected Control Menu.
Control Menu
1
2
3
4
5
1. Operate below functions.
•Power.........Turn the power ON/OFF.
•Mute ........... Turns off the volume temporarily.
• Vol-/Vol+ ....Adjust the volume of the sound.
2. Change the input mode.
3. Operate below functions.
•Contrast ........ Adjusts the contrast.
•BlackLevel ... Adjusts the brightness.
•Colors ........... Adjusts the color intensity.
•Sharpness..... Adjusts the sharpness.
4. Operates the menu screen for the monitor.
5. SwitchesthepagestoTools,Info,Helptab.
Tools
1
2
3
1. SettingforCrestronControl.
2. Settingformonitornetwork.
•DHCP
•IPAddress
•SubnetMask
• Default Gateway
3. SecuritySetting.
Setsthepasswordfortheuserandadministratorsrightson
Control Menu.
Info
12
1. Display below information.
•DisplayName
• Mac Address
•Resolution
2. Display below status.
•PowerStatus
•Input
Help
Sendsorreceivesmessagestotheadministratorswhouses
“Crestron Connected”.
60
E
Controlling the Monitor with a computer (LAN)
[Advanced operation]
Command-based control
You can control the monitor using RS-232C commands
(see page 42) via terminal software and other appropriate
applications.
In order to use this function, enable a connection to the
monitor through the web browser.
Read the manual for the terminal software for detailed
instructions.
(1) Connect the computer to the monitor.
1. Specify the IP address and data port number and
connect the computer to the monitor.
When connection has been established successfully,
[Login:] is returned as response.
2. Send the user name set in the SECURITY settings (see
page 55).
• Send [user name] + [ ].
• If the user name is not set or if USE FOR Telnet
CONNECTION is set to OFF, send [ ].
• When the transmission is successful, [ Password:]
is returned as response.
3. Send the password set in the SECURITY settings (see
page 55).
• Send [password] + [ ].
• If the password is not set or if USE FOR Telnet
CONNECTION is set to OFF, send [ ].
• When the transmission is successful, [OK ] is
returned as response.
(2) Send commands to control the monitor.
• The commands used are the same as those for RS-
232C. Refer to the communication procedure (see
page 38) for operation.
• Usable commands are provided in the RS-232C
command table (see page 42).
(3) Disconnect the connection with the monitor and
quit the function.
1. Send [BYE ].
When the transmission is successful, [goodbye] is
returned and the connection is disconnected.
TIPS
• Connection is automatically disconnected when the
time specied in AUTO LOGOUT TIME elapses over a
no-communication period.
61 E
Troubleshooting
If you are experiencing any problem with your display, before
calling for service, please review the following troubleshooting
tips.
There is no picture or sound.
• Is the power cord disconnected? (See page 15.)
• Is the main power switch off? (See page 18.)
• Is the monitor in standby mode (the power LED illuminating
in orange)? (See page 18.)
• Make sure correct input mode is selected. (See page 21.)
• If any external equipment is connected, make sure the
equipment is operating (playing back).
Remote control does not work.
• Are the batteries inserted with polarity (+,-) aligned? (See
page 17.)
• Are the batteries exhausted?
• Point the remote control unit toward the remote control
sensor. (See page 17.)
• Is the menu display hidden or is operation disabled? (See
page 37.)
• Is the PN-ZR02 (optional) remote control sensor box
connected properly? (See page 14.)
• If you are using multiple monitors, is the RS-232 cable
connected properly? Has the ID No. been set?
• Do the remote control numbers on the remote control unit
and on the monitor match?
Check the numbers on INFORMATION. (See page 36.)
The remote control unit’s buttons for operating the HDMI-
connected device do not work.
• Is HDMI CEC LINK set to AUTO under INPUT SELECT on
the SETUP menu?
• Switch to a different input mode, and then try switching the
input mode back to HDMI.
Sound from left and right speakers is reversed.
Sound is heard from only one side.
• Are audio cables connected properly?
There is a picture but no sound.
• Is the sound muted?
• Make sure the volume is not set to minimum.
• Are audio cables connected properly?
Unstable video.
• The signal may be incompatible.
• Try the automatic screen adjustment when the
D-SUB[RGB] is used.
The video from the HDMI input terminal does not appear
properly.
• Is the HDMI cable HDMI standard compliant? The monitor
will not work with cables that are not standard compliant.
• Is the input signal compatible with this monitor? (See pages
65 and 66.)
The video from the DVI-D input terminal does not appear
properly.
• Is the input signal compatible with this monitor? (See page
65.)
• Turn off the power to the connected equipment and then
turn the power on again.
The video from D-Sub input terminal does not appear
correctly.
• Is the setting for D-SUB of INPUT SELECT on the SETUP
menu correct? (See page 28.)
• Is the input signal compatible with this monitor? (See pages
65 and 66.)
The video from the DisplayPort does not appear properly.
• Does the DisplayPort cable support 4K, and is it
DisplayPort standard compliant? The monitor will not work
with cables that are not standard compliant.
• Is the input signal compatible with this monitor? (See page
65.)
• If the monitors are connected in a daisy chain, turn off the
power to all the monitors connected in a daisy chain and
then turn the power on again.
Control buttons do not work.
There is no picture.
• Load noises from outside may be interfering with normal
operation. Turn off the main power and turn it on after
waiting at least 5 seconds, and then check the operation.
The input mode changes automatically.
• When NO SIGNAL AUTO INPUT SEL. is ON and
the current video signal input stops, the input mode
automatically changes to the mode of an active video
signal.
The input mode may change in the following cases:
- When a computer is in standby mode.
- When video play is stopped with a playback device.
The video does not appear properly even after the
DisplayPort STREAM setting is changed.
• Try restarting the monitor and computer.
• Is the video card MST (Multi Stream Transport) compatible?
If not, set to SST (Single Stream Transport).
Power LED ashes red.
“STATUS [xxxx]” appears in the corner of the screen.
• Hardware has a problem. Turn off the monitor and request
repair from your SHARP dealer.
(When STATUS ALERT is set to OSD & LED. This varies
depending on the setting.)
When “AUTO DIMMING” is displayed.
• When the internal temperature of the monitor rises
excessively, the brightness of the backlight automatically
decreases in order to prevent a further temperature rise. If
you attempt to adjust the brightness while the monitor is in
this state, “AUTO DIMMING” is displayed and you cannot
change the brightness.
• Remove the cause of the excessive temperature rise.
The monitor makes a cracking sound.
• You may occasionally hear a cracking sound from the
monitor. This happens when the cabinet slightly expands
and contracts according to change in temperature. This
does not affect the monitor’s performance.
62
E
The Power LED is ashing in red and green alternately.
When “TEMPERATURE” is displayed in the corner of the
screen.
• When the internal temperature of the monitor rises
excessively, the brightness of the backlight decreases
automatically in order to prevent high-temperature-
related problems. When this occurs, “TEMPERATURE” is
displayed on the screen and the Power LED ashes red
and green alternately. (When TEMPERATURE ALERT is
set to OSD & LED. This varies depending on the setting.)
• If the internal temperature rises further, the monitor
automatically enters standby mode. (The Power LED
continues ashing red and green alternately.)
• Remove the cause of the excessive temperature rise.
- If the monitor enters standby mode due to a rise in
temperature, to return to normal display, turn the power
switch off and then back on again. The monitor, however,
will enter standby mode again if the cause of the
temperature rise is not eliminated. (See page 7.)
- Check whether the monitor is placed at a location where
a quick rise in temperature is likely. Internal temperature
rises quickly if the vents on the monitor are blocked.
- Internal temperature rises quickly if dust accumulates
inside the monitor or around the vents. Remove dust if
possible. Ask SHARP dealer about removing internal dust.
Troubleshooting
63 E
Specications
nProduct Specications
Model PN-V701
LCD component 70" Class [69-1/2 inch (176.6cm) diagonal] TFT LCD
Max. resolution (pixels) 1920 x 1080
Max. colors Approx. 1.06 billion colors
Pixel pitch 0.802 mm (H) × 0.802 mm (V)
Brightness (typical) *1700 cd/m2
Contrast ratio (typical) *14000 : 1
Viewing angle 178° right/left/up/down (contrast ratio ≥ 10)
Screen active area inch (mm) 60-9/16 (W) x 34-1/16 (H) (1538.9 x 865.6)
Computer input signal
Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75 Ω],
DisplayPort 1.2, HDMI
Sync signal Horizontal/vertical separate (TTL: positive/negative), Sync-on-green *2,
Composite sync (TTL: positive/negative) *2
Plug and play VESA DDC2B
Power management VESA DPMS, DVI DMPM
Input terminals Video Mini D-sub 15 pin, 3 rows x 1
DVI-D 24 pin (HDCP compatible) x 1
HDMI x 2
DisplayPort x 1
Serial (RS-232C) D-sub 9 pin x 1
Audio 3.5 mm mini stereo jack x 1
Control kit x 1
Output terminals Video DisplayPort x 1
Serial (RS-232C) D-sub 9 pin x 1
Audio 3.5 mm mini stereo jack x 1
LAN terminal 10 BASE-T/100 BASE-TX
Expansion slot 13V, 2.0 A
(power supplied when expanding the functions with an optional part)
Power requirement AC 100 V - 240 V, 4.2 A, 50/60 Hz
Operating temperature *332°F to 104°F (0°C to 40°C)
Operating humidity 20% to 80% (no condensation)
Power consumption
(Maximum / input signal waiting mode *4 *5 /
standby mode *4 *6)
380 W / 2.5 W / 0.5 W
Dimensions (excluding protrusions) inch (mm) Approx. 60-3/4 (W) x 4-13/16 (D) x 34-1/4 (H) (1543.7 x 122 x 870.4)
Weight lbs. (kg) Approx. 81.6 (37)
*1 When UNIFORMITY is set to MODE1.
Brightness and contrast ratio will depend on input mode and other picture settings. Brightness level will decrease over time. Due to the
nature of the equipment, it is not possible to precisely maintain a constant level of brightness.
*2 D-Sub input terminal only.
*3 Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such
cases, please check the temperature condition specied by the optional equipments.
*4 When the optional part is not installed.
*5 When NO SIGNAL AUTO INPUT SEL. is set to OFF.
*6 When POWER SAVE MODE is set to ON. When POWER SAVE MODE is set to OFF: 1.0 W
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for product improvement
without prior notice. The performance specication gures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
nPN-ZR02 (optional) Product Specications
Model PN-ZR02
Remote control sensor box dimensions inch (mm) Approx. 1-3/8 (W) x 7/8 (D) x 5-1/8 (H) (34.2 x 23 x 130)
Remote control sensor box weight lbs. (kg) Approx. 0.220 (0.1)
64
E
Specications
nDimensional Drawings
Note that the values shown are approximate values.
VESA holes *
15-3/4 [400]
7-7/8
[200]
60-3/4 [1543.7] 7-7/8
[200]
Unit: inch [mm]
4-13/16
[122]
2-3/4
[70]
1-11/16
[43]
Opening width (60-5/8 [1539.3])
Opening height (34-1/8 [866])
34-1/4 [870.4]
When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method.
SHARP recommends using M6 screws and tighten the screws.
Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in serious
personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch
(8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times or
more the weight of the monitor.
nPower management
This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in
order for the monitor’s power management function to work.
DPMS: Display Power Management Signaling
DPMS Screen Power
consumption Hsync Vsync
ON STATE Display 380 W Yes Yes
STANDBY No
display 2.5 W *
No Yes
SUSPEND Yes No
OFF STATE No No
* When NO SIGNAL AUTO INPUT SEL. is set to OFF.
DMPM: Digital Monitor Power Management
DMPM Screen Power
consumption
Monitor ON Display 380 W
Active OFF No display 2.5 W *
nDDC (plug and play)
The monitor supports the VESA DDC (Display Data Channel) standard.
DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters
is exchanged between the two. This function can be used if the computer supports DDC and it has been congured to detect
plug-and-play monitors.
There are several types of DDC, depending on the communication method used. This monitor supports DDC2B.
65 E
nCompatible signal timing (PC)
*1 Displays a reduced image, except in Dot by Dot. In Dot by Dot, the image will be cut down to panel size then displayed.
*2 Used when ENLARGE is ON. Using a single monitor for this setting causes image quality degradation. The image cannot be displayed on the sub
screen.
VESA
Wide
US TEXT
Sun
Screen resolution Hsync Vsync Dot frequency Digital
640 × 480
800 × 600
848 × 480
1024 × 768
1152 × 864
1280 × 768
1280 × 800
1280 × 960
1280 × 1024
1360 × 768
1400 × 1050
1440 × 900
1600 × 1200*1
1680 × 1050
1920 × 1200*1
1280 × 720
1920 × 1080
3840 × 2160*1*2
4096 × 2160*1*2
720 × 400
1024 × 768
1152 × 900
1280 × 1024
1600 × 1000
31.5kHz
37.9kHz
37.5kHz
35.1kHz
37.9kHz
48.1kHz
46.9kHz
31.0kHz
48.4kHz
56.5kHz
60.0kHz
67.5kHz
47.8kHz
60.3kHz
49.7kHz
60.0kHz
64.0kHz
80.0kHz
47.7kHz
65.3kHz
55.9kHz
75.0kHz
65.3kHz
74.0kHz
44.7kHz
67.5kHz
54.0kHz
56.3kHz
67.5kHz
54.0kHz
31.5kHz
48.3kHz
53.6kHz
56.6kHz
61.8kHz
71.8kHz
71.7kHz
81.1kHz
68.6kHz
60Hz
72Hz
75Hz
56Hz
60Hz
72Hz
75Hz
60Hz
60Hz
70Hz
75Hz
75Hz
60Hz
75Hz
60Hz
60Hz
60Hz
75Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
24Hz
25Hz
30Hz
24Hz
70Hz
60Hz
66Hz
70Hz
66Hz
76.2Hz
67.2Hz
76Hz
66Hz
25.175MHz
31.5MHz
31.5MHz
36.0MHz
40.0MHz
50.0MHz
49.5MHz
33.75MHz
65.0MHz
75.0MHz
78.75MHz
108.0MHz
79.5MHz
102.25MHz
83.5MHz
108.0MHz
108.0MHz
135.0MHz
85.5MHz
121.75MHz
106.5MHz
162.0MHz
146.25MHz
154.0MHz
74.4MHz
148.5MHz
297.0MHz
297.0MHz
297.0MHz
297.0MHz
28.3MHz
64.13MHz
70.4MHz
74.25MHz
94.88MHz
108.23MHz
117.01MHz
134.99MHz
135.76MHz
Yes
Yes
Yes
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
-
-
-
Yes
-
-
-
-
-
-
-
-
Analog
(D-sub)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
-
-
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
DVI-DHDMI
Yes
Yes
Yes
-
Yes
Yes
Yes
-
Yes
Yes
Yes
Yes
-
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
-
-
-
-
-
-
-
DisplayPort
Yes
Yes
Yes
-
Yes
Yes
Yes
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
Yes
Yes
Yes
Yes
Yes
-
Yes
-
-
-
-
-
-
-
-
• Depending on the connected computer, images may not be displayed properly even if the compatible signal described above is input.
• The frequency values for the Sun are reference values.
Specications
66
E
Specications
nCompatible signal timing (AV)
Screen resolution Frequency HDMI Component
1920 × 1080p 24Hz Yes -
50Hz Yes Yes
59.94Hz Yes Yes
60Hz Yes Yes
1920 × 1080i 50Hz Yes Yes
59.94Hz Yes Yes
60Hz Yes Yes
1280 × 720p 50Hz Yes Yes
59.94Hz Yes Yes
60Hz Yes Yes
720 × 576p 50Hz Yes Yes
720 × 480p 59.94Hz Yes Yes
60Hz Yes Yes
640 × 480p(VGA) 59.94Hz Yes -
60Hz Yes -
720(1440) × 576i 50Hz Yes Yes
720(1440) × 480i 59.94Hz Yes Yes
60Hz Yes Yes
67 E
Specications
nHDMI input terminal pins
(HDMI Connector)
No. Function No. Function
1TMDS data 2+ 11 TMDS clock shield
2 TMDS data 2 shield 12 TMDS clock-
3 TMDS data 2- 13 CEC
4TMDS data 1+ 14 N.C.
5 TMDS data 1 shield 15 SCL
6 TMDS data 1- 16 SDA
7TMDS data 0+ 17 DDC/CEC GND
8 TMDS data 0 shield 18 +5V
9 TMDS data 0- 19 Hot-plug detection
10 TMDS clock+
nD-sub input terminal pins
(Mini D-sub 15 pin)
No. Function No. Function
1 Red video signal input 9 +5V
2 Green video signal input 10 GND
3 Blue video signal input 11 N.C.
4 N.C. 12 DDC data
5 GND 13 Hsync signal input
6 GND for red video signal 14 Vsync signal input
7GND for green video signal 15 DDC clock
8 GND for blue video signal
nDisplayPort input terminal pins
(DisplayPort 20 pin)
No. Function No. Function
1 MainLane 3- 11 Gnd
2 Gnd 12 MainLane 0+
3MainLane 3+ 13 Gnd
4 MainLane 2- 14 Gnd
5 Gnd 15 Aux+
6MainLane 2+ 16 Gnd
7 MainLane 1- 17 Aux-
8 Gnd 18 Hot-plug detection
9MainLane 1+ 19 Gnd
10 MainLane 0- 20 3.3V
nRS-232C input terminal pins
(D-sub 9 pin)
No. Function No. Function
1 N.C. 6 N.C.
2 Transmitted data 7 N.C.
3 Received data 8 N.C.
4 N.C. 9 N.C.
5 GND
nDVI-D input terminal pins
(DVI-D 24 pin)
No. Function No. Function
1 TMDS data 2- 13 N.C.
2TMDS data 2+ 14 +5V
3 TMDS data 2/4 shield 15 GND
4 N.C. 16 Hot-plug detection
5 N.C. 17 TMDS data 0-
6 DDC clock 18 TMDS data 0+
7 DDC data 19 TMDS data 0/5 shield
8 N.C. 20 N.C.
9 TMDS data 1- 21 N.C.
10 TMDS data 1+ 22 TMDS clock shield
11 TMDS data 1/3 shield 23 TMDS clock+
12 N.C. 24 TMDS clock-
68
E
nDisplayPort output terminal pins
(DisplayPort 20 pin)
No. Function No. Function
1MainLane 0+ 11 Gnd
2 Gnd 12 MainLane 3-
3 MainLane 0- 13 Gnd
4MainLane 1+ 14 Gnd
5 Gnd 15 Aux+
6 MainLane 1- 16 Gnd
7MainLane 2+ 17 Aux-
8 Gnd 18 Hot-plug detection
9 MainLane 2- 19 Gnd
10 MainLane 3+ 20 3.3V
nRS-232C output terminal pins
(D-sub 9 pin)
No. Function No. Function
1 N.C. 6 N.C.
2 Received data 7 N.C.
3 Transmitted data 8 N.C.
4 N.C. 9 N.C.
5 GND
Specications
69 E
• When installing, removing or moving the monitor, ensure that this is carried out by at least 2 people.
• Be sure to use a wall-mount bracket designed or designated for mounting the monitor.
• This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary for some materials
such as plaster / thin plastic board / wood before starting installation.
• This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight of the monitor.
Install by the most suitable method for the material and the structure.
• To attach a VESA-compliant mounting bracket, use M6 screws that are 5/16 inch (8 mm) to 3/8 inch (10 mm) longer than the
thickness of the mounting bracket.
Screws (M6)
Mounting bracket
Monitor mounting
5/16 - 3/8 inch (8-10 mm)
• Do not use an impact driver.
• When moving the monitor, be sure to hold it with the handles. Do not hold the top, bottom, or sides of the monitor. Do not
hold the LCD panel. Also, do not orient the monitor so that the LCD panel faces the ground. This may cause product damage,
failure, or injury.
• When performing an installation where the monitor is stacked, please install it such that load is not placed on the monitor.
• After mounting, please carefully ensure the monitor is secure, and not able to come loose from the wall or mount.
• Do not use any screw holes other than VESA holes for installation.
Mounting Precautions
(For SHARP dealers and service engineers)
PN-V701 Me EN17F(1)