Table of Contents
StarTech.com ARMSLIM User Manual
Displayed below is the user manual for ARMSLIM by StarTech.com which is a product in the Monitor Mounts & Stands category. This manual has pages.
Related Manuals
Manual Revision: 09/13/2019
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
ARMSLIM
Slim Desk Mount Articulating Monitor Arm
with Cable Management
*actual product may vary from photos
Instruction Manual
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Introduction ............................................................................................ 1
Packaging Contents ........................................................................................................................ 1
Product Overview ..................................................................................2
Installation ..............................................................................................3
Desk / Grommet Mounting ................................................................................................................... 3
Attaching the Display .............................................................................................................................. 7
Adjusting Monitor Mount Resistance ................................................................................................ 9
Specications .......................................................................................... 11
Technical Support ..................................................................................12
Warranty Information ............................................................................ 12
Instruction Manual
1
Introduction
Packaging Contents
Monitor Arm
Qty: 1
2-in-1 Desk/Grommet
Clamp
Qty: 1
Thumb Screws
Qty: 4
6mm Allen Wrench
Qty: 1
3mm Allen Wrench
Qty: 1
1 2 3
4 5
Instruction Manual
2
Product Overview
147 mm
<7 kg
Instruction Manual
3
Note: The Desk Clamp can support a desk / table thickness from ¾ - 3.94 in (20
– 100 mm). Depending on the thickness of your desk / table, the clamp can be
adjusted smaller by removing the 4 screws and raising the bottom portion of the
clamp as shown below.
Installation
Warning! It is the installer’s responsibility to ensure that the combined weight of all
components does not exceed the maximum 7 kg (15.43 lbs) weight capacity of the
mounting arm.
Desk / Grommet Mounting
The Monitor Arm can be clamped to a desk / table, or mounted through a grommet
hole. Instructions for both will be provided in the following sections.
Desk Mount
1. Slide the 2-in-1 Clamp (2) opening around the edge of your desk in your desired
location. Tighten by hand to secure, ensuring that the Pressure Plate is making full
contact with the bottom of the desk surface.
Instruction Manual
4
2. Slide the Monitor Arm (1) onto the base and tighten the set screw on the back of the
base, using the 3mm Allen Wrench (5).
Instruction Manual
5
2. Remove the Phillips Screw and the 2 Washers from the top of the Pressure Plate and
then slide the Hand Screw out of the clamp.
Grommet Mount
1. To convert the 2-in-1 Clamp to a Grommet Mount, turn the Clamp upside-down and
remove the 4 screws that join the clamp to the base of the monitor arm, using the
3mm Allen Wrench (5).
3. Slide the Pressure Plate back onto the Hand Screw (without the Washers or Phillips
Screw from above).
Instruction Manual
6
4. Place the base of the Monitor Arm (1) over the grommet hole and thread the Hand
Screw from below until secure. Ensure that the Pressure Plate is making full contact
with the desk surface.
Note: The Grommet Clamp can support a desk / table thickness from ¾ - 1.97 in
(20 – 50 mm)
Instruction Manual
7
5. Slide the Monitor Arm (1) onto the base and tighten the set screw on the back of the
base, using the 3mm Allen Wrench (5).
Attaching the Display
1. Carefully place your display face down on a protective surface to access the
mounting points.
2. Press in on the latch at the top of the Monitor Arm and pull up to remove the
Mounting Bracket.
Instruction Manual
8
3. Attach the display to the Mount Bracket using the 4 Thumb Screws (3).
Warning: Do not over-tighten the screws and stop immediately if you encounter
resistance to avoid damage to your display. Ensure that all screws being used are the
same length and thread type.
4. Slide the monitor mount back onto the arm until it clicks into place.
Instruction Manual
9
Adjusting Monitor Mount Resistance
Warning: Forced movement of the Mount Bracket without loosening the screws may
damage the product or the mounted display.
Always support your display from underneath when making any adjustments to the
LCD Arm or Mount Bracket to avoid damage to the display.
Note: For all adjustments outlined below, turning the screw clockwise will increase the
resistance, while turning the screw counter-clockwise will decrease resistance.
To increase / decrease the spring resistance, adjust the screw located on the top of the
arm, using the 6mm Allen Wrench (4). The indicator area on the arm is for reference
only, but can be used to approximate the appropriate resistance for your monitor by
weight.
Instruction Manual
10
To increase / decrease the tilt resistance, adjust the set screw located on the side of the
Monitor Mount joint, using the 6mm Allen Wrench (4).
To increase / decrease swivel resistance, adjust the set screws located beneath the
swivel points using a Phillips screwdriver, or on the base of the arm using the 3mm
Allen Wrench (5).
Instruction Manual
11
Specications
Weight Capacity 15.43 lbs (7 kg)
Max Display Size 26”
VESA Compatibility 75x75 mm and 100x100 mm
Maximum Mounting Surface Thickness 3.94 in (100 mm)
Instruction Manual
12
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a ten-year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.