Intellinet 507776 User Manual
Displayed below is the user manual for 507776 by Intellinet which is a product in the KVM Switches category. This manual has pages.
Related Manuals
INT-LCD-KVM-SWITCH_UM-0317_REV5.01
LCD KVM Switch
User Manual
Models 507622, 507738, 507745, 507769, 507776, 507844,
507882, 507899, 507905, 507912, 507936
Model Shown: 507622
LCD VGA/DVI/Cat5 KVM Switch
2
LCD KVM Switch User Manual
Compliance Statements
U.S. Federal Communications Commission (FCC) Interference Statement
This product has been tested and found to comply with FCC regulations Class B (Class B) digital device and FCC
specifications Details of Section 15. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if
not installed and used in accordance with the instructions may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures: reorient or relocate the
receiving antenna; increase the separation between the equipment and the receiver; connect the equipment to an outlet
on a circuit different from the receiver; or consult the dealer or an experienced radio/TV technician for help.
CE / R&TTE
English: This device complies with the requirements of R&TTE Directive 1999/5/EC. The Declaration of Conformity is available at:
Deutsch: Dieses Gerät enspricht der Direktive R&TTE Direktive 1999/5/EC. Die Konformitätserklärung für dieses Produkt finden Sie unter:
Español: Este dispositivo cumple con los requerimientos de la Directiva R&TTE 1999/5/EC. La declaración de conformidad esta disponible en:
Français: Cet appareil satisfait aux exigences de la directive R&TTE 1999/5/CE. La Déclaration de Conformité est disponible à:
Polski: Urządzenie spełnia wymagania dyrektywy R&TTE 1999/5/EC. Deklaracja zgodności dostępna jest na stronie internetowej producenta:
Italiano: Questo dispositivo è conforme alla Direttiva 1999/5/EC R&TTE. La dichiarazione di conformità è disponibile al:
intellinetnetworks.com
Waste Electrical & Electronic Equipment
Disposal of Electronic Equipment (applicable in the E.U. and countries with separate collection systems)
English: This symbol on the product or its packaging indicates that this product shall not be treated as household waste.
Instead, it should be taken to an applicable collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential negative consequences to the environment
and human health, which could otherwise be caused by inappropriate waste handling of this product. If your equipment
contains easily removable batteries or accumulators, dispose of these separately according to your local requirements.
The recycling of materials will help to conserve natural resources. For detailed information about recycling this product,
contact your local city office, your household waste disposal service or the shop where you purchased this product. In
countries outside of the EU: If you wish to discard this product, contact your local authorities and ask for the correct
manner of disposal.
Deutsch: Dieses auf dem Produkt oder der Verpackung angebrachte Symbol zeigt an, dass dieses Produkt nicht mit dem
Hausmüll entsorgtwerden darf. In Übereinstimmung mit der Richtlinie 2002/96/EG des Europäischen Parlaments und des
Rates über Elektro- und Elektronik-Altgeräte (WEEE) darf dieses Elektrogerät nicht im normalen Hausmüll oder dem
Gelben Sack entsorgt werden. Wenn Sie dieses Produkt entsorgen möchten, bringen Sie es bitte zur Verkaufsstelle
zurück oder zum Recycling-
Sammelpunkt Ihrer Gemeinde.
Español: Este símbolo en el producto o su embalaje indica que el producto no debe tratarse como residuo doméstico. De
conformidad con la Directiva 2002/96/CE de la UE sobre residuos de aparatos eléctricos y electrónicos (RAEE), este
producto eléctrico no puede desecharse se con el resto de residuos no clasificados. Deshágase de este producto
devolviéndolo a su punto de venta o a un punto de recolección municipal para su reciclaje.
Français: Ce symbole sur Ie produit ou son emballage signifie que ce produit ne doit pas être traité comme un déchet
ménager. Conformément à la Directive 2002/96/EC sur les déchets dʼéquipements électriques et électroniques (DEEE),
ce produit électrique ne doit en aucun cas être mis au rebut sous forme de déchet municipal non trié. Veuillez vous
débarrasser de ce produit en Ie renvoyant à son point de vente ou au point de ramassage local dans votre municipalité, à
des fins de recyclage.
Italiano: Questo simbolo sui prodotto o sulla relativa confezione indica che il prodotto non va trattato come un rifiuto
domestico. In ottemperanza alla Direttiva UE 2002/96/EC sui rifiuti di apparecchiature elettriche ed elettroniche (RAEE),
questa prodotto elettrico non deve essere smaltito come rifiuto municipale misto. Si prega di smaltire il prodotto
riportandolo al punto vendita o al punto di raccolta municipale locale per un opportuno riciclaggio.
Polski: Jeśli na produkcie lub jego opakowaniu umieszczono ten symbol, wówczas w czasie utylizacji nie wolno wyrzucać
tego produktu wraz z odpadami komunalnymi. Zgodnie z Dyrektywą Nr 2002/96/WE w sprawie zużytego sprzętu
elektrycznego i elektronicznego (WEEE), niniejszego produktu elektrycznego nie wolno usuwać jako nie posortowanego
odpadu komunalnego. Prosimy o usuniecie niniejszego produktu poprzez jego zwrot do punktu zakupu lub oddanie do
miejscowego komunalnego punktu zbiórki odpadów przeznaczonych do recyklingu.
LCD VGA/DVI/Cat5 KVM Switch
3
Table of Contents
COMPLIANCE STATEMENTS ................................................................................................................................................. 2
PRODUCT MODELS & DESCRIPTIONS .................................................................................................................................. 4
PACKAGE CONTENTS & MANUAL INFORMATION ............................................................................................................... 4
A NOTE TO THE USER .......................................................................................................................................................... 4
DESCRIPTION OF SYMBOLS .................................................................................................................................................. 4
CHAPTER 1 ‒ INTRODUCTION ....................................................................................................................................... 5
1.1 PRODUCTS OVERVIEW ................................................................................................................................................... 5
1.1.1 Hardware Requirements ........................................................................................................................................ 5
1.1.2 Supported Operating Systems ................................................................................................................................ 6
1.2 PARTS ............................................................................................................................................................................. 7
1.2.1 Front View .............................................................................................................................................................. 7
1.2.2 Modular Switch Rear Views ................................................................................................................................... 8
1.3 VIEWS AND DIMENSIONS ............................................................................................................................................... 9
CHAPTER 2 ‒ HARDWARE INSTALLATION ............................................................................................................... 10
2.1 STACKING AND INSTALLATION NOTES ........................................................................................................................ 10
2.2 STANDARD RACK MOUNTING ..................................................................................................................................... 10
2.3 KVM MODULE ASSEMBLY & DISASSEMBLY .............................................................................................................. 11
2.4 KEYBOARD DISASSEMBLY .......................................................................................................................................... 12
2.5 EXPANSION MODULE INSTALLATION .......................................................................................................................... 12
2.6 SINGLE DEVICE INSTALLATION ................................................................................................................................... 14
2.6.1 VGA Port KVM Module Installation .................................................................................................................... 14
2.6.2 Cat5 Port KVM Module Installation .................................................................................................................... 15
2.6.3 DVI Port KVM Module Installation ..................................................................................................................... 16
2.7 CASCADE DEVICE INSTALLATION ............................................................................................................................... 17
2.7.1 VGA Port LCD KVM Switch Cascade ................................................................................................................. 17
2.7.2 Cat5 Port LCD KVM Switch Cascade ................................................................................................................. 18
CHAPTER 3 ‒ BASIC OPERATIONS ............................................................................................................................. 19
3.1 HOT-SWAP ................................................................................................................................................................... 19
Hot-Swap Console Port ................................................................................................................................................ 19
3.2 CONNECTION PORT SELECTION ................................................................................................................................... 19
3.2.1 Manual Switching: ............................................................................................................................................... 19
3.2.2 OSD Menu Screen Selection ................................................................................................................................ 19
3.2.3 Hot Key Selection ................................................................................................................................................. 20
3.3 POWER OFF AND RESTART .......................................................................................................................................... 20
3.4 OPENING / CLOSING / LOCKING THE LCD ................................................................................................................... 20
CHAPTER 4 ‒ ON-SCREEN DISPLAY (OSD) OPERATIONS ................................................................................... 21
4.1 OSD LOGIN .................................................................................................................................................................. 21
4.2 OSD HOT KEY ............................................................................................................................................................. 21
4.3 OSD MAIN MENU ........................................................................................................................................................ 21
4.4 OSD MAIN SCREEN HEADINGS ................................................................................................................................... 21
4.5 OSD FUNCTIONS .......................................................................................................................................................... 21
4.5.1 F1:GOTO .......................................................................................................................................................... 22
4.5.2 F2:SCAN .............................................................................................................................................................. 22
4.5.3 F3:LIST ................................................................................................................................................................ 22
4.5.4 F4 QV ................................................................................................................................................................... 23
4.5.5 F5 EDIT ............................................................................................................................................................... 23
4.5.6 F6:SET ................................................................................................................................................................. 23
APPENDIX ........................................................................................................................................................................... 27
A‒1 GENERAL SAFETY INSTRUCTIONS ............................................................................................................................. 27
A‒2 CABINET INSTALLATION ............................................................................................................................................ 27
A‒3 SPECIFICATIONS ......................................................................................................................................................... 28
A.3.1 VGA Series LCD KVM Switch ............................................................................................................................. 28
A.3.2 Cat5 Series LCD KVM Switch ............................................................................................................................. 29
A.3.3 DVI Series LCD KVM Switch .............................................................................................................................. 30
A.3.4 LCD Module Specifications ................................................................................................................................. 31
WARRANTY ....................................................................................................................................................................... 32
NOTES .................................................................................................................................................................................. 33
LCD VGA/DVI/Cat5 KVM Switch
4
Product Models & Descriptions
Package Contents & Manual Information
Name
Quantity/Unit
Description
LCD KVM Console
1 pc.
LCD Computer
KVM Cables
N pc.
Cable qts. vary based on product descr.
Power Supply
1 pc.
Built-in power supply
Power Cable
1 pc.
Standard 1.8 m (5.9 ft.) power cord
Instructions
1 pc.
Paper manual
Mounting Brackets
2 pcs.
LCD KVM single-mount bracket
Lock ear
2 pcs.
Fixing rear panel
Screw-Install Kit
1 pc.
Screw-in mounting bracket
• Ensure that all parts are present and free from damage. If parts are missing or damaged, contact your Intellinet
dealer or distributor.
• Make sure to read this manual carefully before installing and operating the Intellinet LCD KVM Switch. Only
professionals should install this product.
A Note to the User
From time to time, Intellinet may modify and/or alter the information, documentation and specifications contained in this
manual, with or without prior notice. If the software needs to be updated after purchase, the user and/or her or his
dealer/distributor will be responsible for all necessary service and repair. The user is responsible for correcting any radio
or television interference that this equipment may cause. Make sure to set the voltage correctly before use. Intellinet will
not be liable for any damage resulting from incorrect selection of operating voltage.
A typical Liquid Crystal Display (LCD) has millions of pixels. A defective pixel is one that is off or does not display the
correct color, which may develop if the screen absorbs a slight impact during transportation or even in the process of
manufacturing. It is normal for a product with an LCD screen to arrive to the consumer with a few of these defects. The
user should contact her or his dealer/distributor in the event that there is more damage than described here.
Description of Symbols
• [ ] Brackets around a word indicate that the user must complete a keyboard action based on the text in the
brackets. For example, [Enter] indicates that the user needs to press the "Enter" key. When more than one key
needs to be pressed at the same time, the manual denotes this command by joining a plus sign between the two
keys (e.g., [Ctrl+Alt]).
• 1. Numbers indicate the operating steps that are necessary to complete a function.
• ✚ indicates that the information is for the user's reference but is not essential to the procedure.
• ✪ The star-in-the-circle symbol indicates that the information is very important.
Model
Name
Description
507622
Rackmount 17" LCD Console
17-Inch LCD Panel, 1U, Modular System
507738
Rackmount 19" LCD Console
19-Inch LCD Panel, 1U, Modular system
507745
Rackmount 19" LCD Console DVI
19-Inch LCD Panel, 1U, DVI, Modular system
507769
VGA 1-Port Cable for KVM Console
PS2, USB and VGA Connectors
507776
Modular 8-Port VGA KVM Switch
For Use with Intellinet Product Numbers 507622 or 507738
507844
Modular 16-Port VGA KVM Switch
For Use with Intellinet Product Numbers 507622 or 507738
507822
Modular 8-Port CAT5 VGA KVM Switch
For Use with Intellinet Product Numbers 507622 or 507738
507899
Modular 16-Port CAT5 VGA KVM Switch
For Use with Intellinet Product Numbers 507622 or 507738
507905
DVI 1-Port Cable for KVM Console
PS2, USB and VGA Connectors
507912
Modular 8-Port DVI KVM Switch
For Use with Intellinet Product Number 507745
507936
IP-Function Module for KVM Switches
For Use with Intellinet Modular KVM Console/Switch Range
LCD VGA/DVI/Cat5 KVM Switch
5
Chapter 1 – Introduction
1.1 Products Overview
1.1.1 Hardware Requirements
1.1.1.1 Console
• Rear two USB-A keyboard and mouse ports
• Pre-set USB-A type keyboard and mouse
• A set of USB interface mice
• A set of USB interface keyboards
• Single-ended extension cable (optional)
• IP remote control terminal 1000M network interface (optional installation)
1.1.1.2 Computer
The following devices must be installed on each computer:
• A VGA or DVI video display card
• USB-A connection port
• PS2 / PS2 keyboard, mouse ports
1.1.1.3 Cables
KVM equipment provides five kinds of connection cables according to the user's product:
• LCD KVM switch single-port DVI cable
Computer-side DVI-I & USB
(Type-A) + PS2 keyboard (purple)
+ PS2 mouse (green) to Parallel
(DB37P)
• LCD KVM switch single port VGA cable
Computer-side VGA & USB
(Type-A) + PS2 keyboard (purple)
+ PS2 mouse (green) to Parallel
LCD VGA/DVI/Cat5 KVM Switch
6
• LCD KVM switch VGA cable
VGA & USB
(Type-A) + PS2
keyboard (purple)
+ PS2 mouse
(green) to VGA
• LCD KVM switch DVI cable
DVI-I & USB
(Type-A) + Audio
• Cat5 to VGA connection Dongle
VGA + PS2
keyboard (purple) +
PS2 mouse (green)
to Cat5 port
1.1.2 Supported Operating Systems
System
Version
Windows
Windows 2000/XP/2003/2008/Vista/7/10
Linux
Red Hat
9.0 or higher, Fedora and above, RHEL AS 4, RHEL 5
SuSE
10/11.1, Open SUSE 10.2; SLES 10 SP1
Debian
3.1 / 4.0
Ubuntu
7.04/7.10
UNIX
AIX
4.3 or higher
FreeBSD
5.5 or higher
Sun Solaris
8 or higher
Mac
OS 9.0 to 10.6
Novell
Netware
6.0 or higher
DOS
6.2 or later
LCD VGA/DVI/Cat5 KVM Switch
7
1.2 Parts
1.2.1 Front View
The are two different sizes of LCD screens, as shown below. Refer to the chart for a description of the numeric
values for each graphic.
17" Model
19" Model
Number
Part
Function Description
1
Upper Handle
Pull the handle, slide the LCD module out and push it in
2
Lock
Locks the LCD module; pull out module first, then push into the automatic lock
3
LCD Screen Cover
Opens or closes with the handle; opening and closing angle of 0° – 100°
4
LED Screen
17" or 19" LED/LCD screen – Later referred to as On Screen Displa (OSD)
5
KVM Module
KVM modules can be easily removed and replaced
6
KVM Key Panel
Press this key to enter to manual switch function
7
Front Mount Brackets
For installation into cabinets and racks with screws
8
Touch Mouse Pad
KVM console mouse; can control the computer's operations
9
Slide Rails
LCD module sliding track
10
Keyhole
Corresponds to the latch of the LCD module
11
LCD Keypad Panel
Used to control the LED screen display adjustment and switch
12
Front USB Port
Used to access an external USB keyboard or mouse
LCD VGA/DVI/Cat5 KVM Switch
8
1.2.2 Modular Switch Rear Views
This section shows the available connection types of the Intellinet Removable KVM Switch Modules. Both the
VGA and Cat5 switch types can be optionally configured with Remote Control IP as the images describe.
LCD KVM 8-port VGA Switch
LCD KVM 16-port VGA Switch
LCD KVM 8-port Cat5 Switch
LCD KVM 16-port Cat5 Switch
LCD KVM 8 port DVI Switch
LCD VGA/DVI/Cat5 KVM Switch
9
1.3 Views and Dimensions
4:3 Screen – 17" 16:9 Screen – 19"
Single-Rail LCD KVM Console
Single–Rail Multi-Port KVM Console Dimensions
LCD VGA/DVI/Cat5 KVM Switch
10
Chapter 2 – Hardware Installation
2.1 Stacking and Installation Notes
1. Before proceeding, refer to the important safety information regarding the placement of the LCD KVM
switch, which is listed in the appendix.
2. Before installation, make sure that all the devices connected to the power supply are turned off. Unplug
all power cables from the computer.
3. The LCD KVM switch is packed with stuffing to protect it during transportation and movement. Make
sure the equipment is free from all protective films and fillers before mounting.
Place the LCD KVM switch in a suitable area that will sufficiently and securely support the weight of the equipment plus
additional cables. Make sure that the area is clean and free from other debris that can affect the ventilation and normal
operation of the switch.
2.2 Standard Rack Mounting
1. Remove the mounting brackets and fasten the front bezel to the frame with screws. Slide the back plate with the
rear flange toward the rack until the flange is against the chassis. Then use the screws to secure the rear flange
to the chassis.
2. Slide the LCD KVM unit onto the support flange. Secure the front of the switch to the front of the rack with the
screws provided in the package.
3. Slide the rear-connecting slide bracket along the side rails until it reaches the rear of the switch.
4. Use the screws provided in this package to secure the strip to the rear of the switch.
✪
LCD VGA/DVI/Cat5 KVM Switch
11
2.3 KVM Module Assembly & Disassembly
The Intellinet series of KVM Switches utilizes an LCD screen, keyboard and mouse with detachable, modular switch
components. This design allows the user to change out any the KVM components in the case of damage or if the set-up of
the system changes.
Refer to the following figure for loading and unloading procedures:
1. Once the series of products is placed on the appropriate operating platform, have a screwdriver ready to remove
and replace screws.
2. Remove the KVM assembly and the captive screws on the side brackets as shown to separate the KVM
assembly from the front LCD assembly.
3. Note the connector between the KVM module and the LCD during removal and installation. Otherwise, damage to
the connection may occur with failures between the interface and equipment.
LCD VGA/DVI/Cat5 KVM Switch
12
2.4 Keyboard Disassembly
The following diagram demonstrates how to replace or repair the keyboard portion of the KVM switch.
1. Have the LCD KVM firmly fixed in the rack and the LCD panel open to reveal the keyboard and mouse operating
surface.
2. Feel for the circular opening on the bottom of the keyboard panel and push the keyboard gently from its slot. Find
the connection side of the USB plug and detach it to remove the keyboard. NOTE: When replacing the module,
first plug in the keyboard USB connector, and then replace the keyboard itself into the slot.
2.5 Expansion Module Installation
To quickly and easily upgrade this equipment for remote control of the KVM Switch and its attached devices, use an
Intellinet IP-Function Module for KVM Switches (507936). Follow these steps to complete installation. NOTE: make sure
that the switch is off and disconnected from a power source before beginning installation.
LCD VGA/DVI/Cat5 KVM Switch
13
1. On the rear of the KVM module, find the expansion slot and the blank panel for installation. Use a screwdriver to
remove the screws and the blanking panel.
2. Push the IP module gently into the cavity.
3. Fix the module in place with the screws.
4. Turn on the KVM switch and follow the IP module instructions to complete setup of the IP module.
LCD VGA/DVI/Cat5 KVM Switch
14
2.6 Single Device Installation
The follow section describes how to correctly establish VGA, Cat5 or DVI connections. Note: Before installation, make
sure that the equipment is powered off. To prevent damage to the equipment during installation, make sure that
all installed devices are fully grounded.
2.6.1 VGA Port KVM Module Installation
To install a single-level KVM, complete the following steps. Refer to the diagram below for additional visualization:
1. Plug your USB keyboard and mouse into the USB console port on the back panel of the switch.
2. Using a set of KVM cables that correspond to the model, plug the VGA connector into any available VGA
port on the switch.
3. Plug the corresponding VGA video connector, USB or PS2 connector of the KVM cable into the
corresponding port on the PC.
4. Connect the supplied power cable from the power jack on the switch to an AC power source.
5. Connect the network cable to the IP port of the IP module.
6. Turn on the computer.
1
2
4
3
5
N
E
T
Notes:
1. Make sure that all plugs are connected to the same group of KVM connection port jacks (all connected to
Port1 or all connected to Port2).
2. The IP module is an optional configuration of the product. If the product you purchased does not contain the
module, ignore the related operation in Step 5.
3. Before using the IP module, make the appropriate configuration and complete a network debugging after
accessing the network you want to connect to. Refer to the IP module product manual for how to use and
debug the IP module.
LCD VGA/DVI/Cat5 KVM Switch
15
2.6.2 Cat5 Port KVM Module Installation
To install a single-level KVM, complete the following steps. Refer to the diagram below for additional visualization:
1. Plug your USB keyboard and mouse into the USB console port on the back panel of the switch.
2. Use a set of Cat5e / 6-wire connectors to plug into any available Cat5 port on the switch.
3. Plug a Cat5e / 6-wire connector into the Cat5 connector on the dongle module of the KVM. Connect the
corresponding VGA video connector, USB or PS2 connector of the dongle cable to the corresponding port
on the PC.
4. Connect the supplied power cable from the power jack on the switch to an AC power source.
5. Connect the network cable to the IP port of the IP module.
6. Turn on the computer.
1
2
4
3
5
N
E
T
Notes:
1. Make sure that all plugs are connected to the same group of KVM connection port jacks (all connected to
Port1 or all connected to Port2).
2. The IP module is an optional configuration of the product. If the product you purchased does not contain the
module, ignore the related operation in Step 5.
3. Before using the IP module, make the appropriate configuration and complete a network debugging after
accessing the network you want to connect to. Refer to the IP module product manual for how to use and
debug the IP module.
4. For display problems caused by transmission distance, electromagnetic interference, common ground, etc.,
Intellinet recommends using Cat6 shielded network cable to connect and try to improve the display effect.
LCD VGA/DVI/Cat5 KVM Switch
16
2.6.3 DVI Port KVM Module Installation
To install a single-level KVM, complete the following steps. Refer to the diagram below for additional visualization:
1. Plug your USB keyboard and mouse into the USB console port on the back panel of the switch.
2. Insert the audio cable plug of the microphone and the speaker into the corresponding port.
3. Using a set of DVI KVM cable connectors that correspond to this module, plug them into the available
ports on the switch – DVI to DVI port, USB-B to keyboard port, mouse port, and composite audio plug to
the audio jack.
4. Connect the supplied power cable from the power jack on the switch to an AC power source.
5. Connect the network cable to the IP port of the IP module.
6. Turn on the computer.
1
2
4
3
5
Notes:
1. Make sure that all plugs are connected to the same group of KVM connection port jacks (all connected to
Port1 or all connected to Port2).
2. The IP module is an optional configuration of the product. If the product you purchased does not contain the
module, ignore the related operation in Step 5.
3. Before using the IP module, make the appropriate configuration and complete a network debugging after
accessing the network you want to connect to. Refer to the IP module product manual for how to use and
debug the IP module.
LCD VGA/DVI/Cat5 KVM Switch
17
2.7 Cascade Device Installation
This product can be cascaded to increase the number of controlled devices.
2.7.1 VGA Port LCD KVM Switch Cascade
In the VGA-switch Cascade Mode, the keyboard, mouse and computer connections are the same with the stand-
alone connection. The number part of the description is as follows:
1. A cascaded KVM switch can be connected in two ways—by using a USB KVM cable (as shown in
connection number 2 in the figure) or a PS2 KVM cable (as shown in connection number 1 in the figure).
Connect to the upper-level switcher.
2. The number of computers connected to each level can be freely increased or decreased according to the
user's requirements.
3. Employing the use of the IP module allows for the remote control of the connected devices. This structure
can be handed over to the KVM switch from the top of the local and remote groups with unified control and
management operations.
N
E
T
N
E
T
1
2
3
Note: Cascade Mode divides into two levels. Set the switch in the On-Screen Display (OSD) Menu with two levels
of Hot Keys for two different Hot Key combinations, or the OSD will not start when cascaded. (Refer to the OSD
chapter for details on the OSD Hot Key settings.)
LCD VGA/DVI/Cat5 KVM Switch
18
2.7.2 Cat5 Port LCD KVM Switch Cascade
In the Cat5-switch Cascade Mode, the keyboard, mouse and computer connections are the same with the stand-
alone connection. The number part of the description is as follows:
1. A cascaded KVM switch can be connected in two ways—by using a USB KVM cable (as shown in
connection number 2 in the figure) or a PS2 KVM conversion-module cable and a switch to the next
level to connect.
2. Refer to the connection port shown in figure 2, which is the connection port for Remote Control mode
through the Remote Control console.
3. Employing the use of the IP module allows for the remote control of the connected devices. This
structure can be handed over to the KVM switch from the top of the local and remote groups with
unified control and management operations.
N
E
T
!
2
1
Note: Cascade Mode divides into two levels. Set the switch in the OSD Menu with two levels of Hot Keys for two different
Hot Key combinations, or the OSD will not start when cascaded. (Refer to the OSD chapter for details on the OSD Hot
Key settings.) For display problems caused by transmission distance, electromagnetic interference, common ground, etc.,
Intellinet recommends using Cat6 shielded network cable to connect and try to improve the display effect.
LCD VGA/DVI/Cat5 KVM Switch
19
Chapter 3 – Basic Operations
3.1 Hot-Swap
The KVM switch supports hot-swapping, which allows the user to remove components by unplugging the cables that are
connected computer's port without having to shut down the switch. To make the hot-swap function work properly, adhere
to this information and/or follow these steps:
Hot-swap Computer Connection
In order for the On-Screen Display (OSD) Menu to correspond to the KVM connection-port changes, you must reset the
OSD Menu to display the latest connection port information and OSD menu settings. Refer to the OSD Menu section for
more information about functions and usage.
Hot-Swap Console Port
This product also supports the hot-swap function for the keyboard, mouse and display. It also provides keyboard and
mouse ports for two interface types. Users can select the corresponding device-connection type according to their usage
and carry out corresponding control operation. NOTE: If you access the USB and PS2 keyboard and mouse device, you
do not have to use two types of devices.
3.2 Connection Port Selection
The KVM switch can be used to quickly switch to any computer connected to the KVM in three modes: Manual Selection,
OSD Menu Screen Selection and Hot Key Selection.
3.2.1 Manual Switching:
Use the buttons on the front control panel to select a port.
ˆ8-port model shown
✚ The panel is divided into three areas — from left to right: the online indicator display area, the Port Switch to
Select the display area, and the Port Switch digital button area.
• Online Indicator Display Area
The LEDs in the display area are lit when the controlled computer that is connected to KVM Port is
connected to the line. The LED indicating the port number is illuminated and the KVM online Port status is
shown.
• Port Switch the Display Area
The digital LED indicator in the display area shows the port number of the current working port when status
is displayed or the numeric key number for input when the key switch port changes.
• Port Switch Digital Button Area
This area has the numeric keys of [0] - [9] and [RST] (reset button), [ENT] (confirm button). The number
keys are used to select the port. Input the corresponding port number and press【ENT】to jump to that
computer. To reset the KVM switch, click [RST] for 3-5 seconds.
3.2.2 OSD Menu Screen Selection
LCD OSD Menu key operation:
✚Hotkey Selection
【AUTO】Sets the display setting for the screen to automatically adjust resolution
【MENU】Opens the main menu of the display
【LEFT】Selects the direction within the OSD menu and moves the current selection to the left by one unit
【RIGHT】Selects the direction within the OSD menu and moves the current selection to the right by one unit
【EXIT】Exits the OSD menu
【POWER】Turns the LCD screen on and off
LED for LCD screen status–Indicates different statuses with different colors: red, green, and none. Red
indicates that the LCD screen is connected to power but not receiving a video signal. Green indicates that the
LCD is displaying the video signal of the controlled computer. No display means the power to LCD screen is off.
LCD VGA/DVI/Cat5 KVM Switch
20
3.2.3 Hot Key Selection
This product offers four hotkey switching methods:
【SCRLL】+【SCRLL】+【NUM】/
【CTRL】+【CTRL】+【NUM】/
【ALT】+【ALT】+【NUM】/
【SHIFT】+【SHIFT】+【NUM】
The default hot-key toggle combination is [SCRLL] + [SCRLL] + [NUM], where [NUM] is the keyboard number 1-
16. The KVM switch will switch to the corresponding computer of the port number. To change the key combination
of the hotkey, set and change it in the corresponding option of OSD Menu.
3.3 Power Off and Restart
To power off the KVM switch, do the following before turning it back on:
1. Unplug its power supply.
2. Turn off all computers that are connected to the KVM switch.
3. Wait 10 seconds; then, reconnect the KVM switch.
4. Turn on the computer.
3.4 Opening / Closing / Locking the LCD
1. To open the LCD display screen, flip the screen upwards. The maximum angle that the LCD screen can be
opened is 105 –120°.
2. When in use, the LCD can be unlocked from the side track by the handle on the upper part of the LCD unit. After
unlocking, the LCD module can be pulled out from the slide rail. (Refer to the diagram above for operation.)
3. The screen will automatically pull out the slide after the brake locks the device to prevent random sliding of the
LCD screen components. After the brake lock is activated, the LCD screen will limit the operation by pushing the
slide rail. To manually unlock the KVM switch from the slide rail, pull back both sides locked buttons on each slide
rail. (Refer to the figure above for the specific operation). After unlocking, pushed the switch into the slide rail.
UNLOCK
AUTO LOCK
LCD VGA/DVI/Cat5 KVM Switch
21
Chapter 4 – On-Screen Display (OSD) Operations
This chapter reviews how the switch's menu-driven interface handles the computer switching procedure and provides
instant access to any computer on the installation.
4.1 OSD Login
The OSD function provides a two-level (administrator / user) password mechanism. The factory default setting—i.e., first-
time access—does not require login-password authentication. The default administrator password is admin. To add a
password, enter the OSD menu, and press the 【F6】 "SET" option to set the login password successfully. The
subsequent login requires the correct administrator / user to enter the password in the OSD menu Interface operation.
When entering the setting options, some functions may need to be edited and modified by the administrator. Modify and
change them as needed.
4.2 OSD Hot Key
By default, press the [CTRL] key twice for the OSD menu to appear on the screen of the controlled display and see the
connection/status information and the connected computers.
4.3 OSD Main Menu
• 【F1】–【F6】 at the bottom of the screen accesses the functions of OSD menu, their corresponding operations and
the setting of corresponding functions by keyboard.
• After entering the OSD main screen, the port number in the center of the screen is the port number of the selected
PC. To move up and down through the list one line at a time, use the【↑】 【↓】Arrow Keys and press 【Enter】 to
select the switch port. If the number of rows in the list is larger than the number that the screen can display, the
screen scrolls.
• Press【Esc】to exit the OSD menu interface.
• When the OSD menu is closed, a small blue window will appear on the screen that shows the port number that switch
is currently switched to.
4.4 OSD Main Screen Headings
Heading
Explanation
PN
This column lists the port numbers for all the CPU ports on the installation. The simplest
method to access a particular computer is to move the highlight bar to it, then press
[Enter].
QV
If a port has been selected for Quick View scanning, an arrowhead symbol displays in
this column to indicate so.
PC
The computers that are powered on and are on line have an arrowhead symbol in this
column to indicate so.
NAME
If a port has been given a name, its name appears in this column.
4.5 OSD Functions
OSD functions are used to configure and control the OSD. These functions allow you to rapidly switch to any port, scan
selected ports only, limit the list of views, designate a port as a Quick View Port, create or edit a port name, or make OSD-
setting adjustments.
To activate the OSD function key:
1. Press any function key【F1】–【F6】 at the bottom of main screen to input the function key.
2. On the sub-menu, move the selection column to the option, and then press the 【Enter】 key.
3. Press the【Esc】key to return to the previous menu.
LCD VGA/DVI/Cat5 KVM Switch
22
4.5.1 F1:GOTO
1. To use the “NAME” method, move the highlight bar to “NAME" and press 【Enter】. Input the name of
a port, then press [Enter] to confirm.
2. To use the "PN" method, move highlight bar to “PN” and press 【Enter】. Input the port number, and
then press 【Enter】 to switch. If the port number is invalid, it will remind the user to input again.
3. To return to main menu, press [Esc].
Note:
1. When keying a name that matches one that already exists, the matched name will appear on the
screen. Press 【Enter】to switch to that port.
2. In the "PN" port input box, only allow the input of numbers. The input of other characters is regarded as
invalid—the equipment notes this to the user by issuing a warning tone.
4.5.2 F2:SCAN
The "SCAN" function performs automatic port scanning of the connected computers. Users can switch ports in
order to view the corresponding port computer status.
• The SCAN function can automatically scan from the current selected port; users can set the scan interval.
• When scanning, a small window on the screen indicates the current port number.
• Press [Space] to stop scanning, and the KVM switches to the port last scanned.
4.5.3 F3:LIST
The LIST function enables the broadening or narrowing of the scope for which ports the OSD will display on the
main screen.
Many of the OSD functions only operate on the computers that have been selected for listing on the main screen
with this function. The choices and their meanings are given in the table below:
Choice
Meaning
ALL
Lists all of the ports on the installation.
QVIEW
Lists only the ports that have been selected as Quick View Ports.
POWERED ON
Lists only the ports that have their attached computers powered on.
POWERED ON + QVIEW
Lists only the ports that have their attached computers powered on and have been
selected as Quick View Ports.
QVIEW + NAME
Lists only the ports that have been selected as Quick View Ports and have name.
NAME
Lists only the ports that have names.
Move the highlight bar to the desired selection, then press [Enter]. An icon appears before the choice to indicate that it is
currently selected. Afterward is a return to the OSD main screen with the newly formulated list displayed.
LCD VGA/DVI/Cat5 KVM Switch
23
4.5.4 F4 QV
The QV function selects a port for Quick View. Move the highlight bar to a port, press [F4] and an icon of an
upward facing triangle appears. Press [F4] again and the icon disappears.
4.5.5 F5 EDIT
The EDIT function creates or edits the name of a port. Pressing [F5] brings up a pink edit box. Input a name, and
then press [Enter]. The port is set a name and it will appear on the screen.
4.5.6 F6:SET
To change the settings:
1. Move the highlight bar to an option and press 【Enter】.
2. After selecting an item, the sub-menu and the further options provided will appear. To select it, double-click the
mouse or move the selection column to the option, and then press the [Enter] key; an icon will appear. Select the
option before to indicate that the item has been selected. The settings are described in the following table:
Settings
Function
OSD ACTIVATING HOTKEY
OSD Menu Activates hotkey combination selection
settings
SWITCH HOTKEY
KVM port switch hot-key combination selection setting
CHANNEL DISPLAY MODE
Port display mode selection
CHANNEL DISPLAY DURATION
Select the Port form to display the Dwell Time setting
CHANNEL DISPLAY POSITION
Select the port form display location settings
SCAN DURATION
Port scan dwell time setting
SET PASSWORD
User login password settings
SET SUPER PASSWORD
The administrator login password settings
CLEAR THE NAME LIST
Clear the port name setting
RESTORE DEFAULT VALUE
Reset
LOCK CONSOLE
OSD Menu Password Login Function settings
LCD VGA/DVI/Cat5 KVM Switch
24
4.5.6.1 OSD ACTIVATING HOTKEY
This screen provides the user with four hotkey combinations. Use the keyboard's 【↑】 【↓】 buttons
to move the cursor to select an item, and then press 【Enter】 to save. The default is to use 【CTRL】【
CTRL】as the OSD menu start hotkey.
4.5.6.2 SWITCH HOTKEY
This screen provides the user with four hotkey combinations. Use the keyboard's 【↑】 【↓】 buttons
to move the cursor to select an item, and then press 【Enter】 to save. The default is to use【SCRLL】
【SCRLL】【NUM】 as the OSD menu start hotkey.【NUM】 is the numeric keypad of the keyboard.
Depending on the model number a valid numeric range can be from 【1】 - 【16】.
4.5.6.3 CHANNEL DISPLAY MODE
This function provides three different port display modes: PN + NAME (the port number and port name),
PN (only shows the port number), and NAME (only shows the port name). Adjust this according to system
requirements. The initial default is PN + NAME mode.
LCD VGA/DVI/Cat5 KVM Switch
25
4.5.6.4 CHANNEL DISPLAY DURATION
This screen allows the user to adjust the time the tip window will stay on screen.
The options are as follows:
• 3 SECOND—The tip window lasts for 3 seconds;
• ALWAYS ON—The tip window is always on the screen.
4.5.6.5 CHANNEL DISPLAY POSITION
This screen allows the user to adjust the position of the tip window.
A small blue window appears on the screen. Use an arrow key to move it; then, press [Enter] to specify
the position.
4.5.6.6 SCAN DURATION
This screen allows the user to adjust the Duration for scanning one port. Move the highlight bar to an
option and press [Enter] to select it.
4.5.6.7 SET PASSWORD
This screen allows the user to set a new password. First, enter the old password; then, enter a new
password and confirm it. The new password is set. If an error occurs, the screen will remind users.
4.5.6.8 SET SUPER PASSWORD
When setting the administrator password, it is necessary to enter the correct password. Before a new
password is updated, input the previous password twice for the new password to take effect.
LCD VGA/DVI/Cat5 KVM Switch
26
4.5.6.9 CLEAR THE NAME LIST
This function clears the name of a port in the OSD menu. If you use this function, all the port names will
be emptied, so proceed carefully. It is necessary to verify the administrator password. Afterward, input the
【Y】key and press【Enter】 to confirm the operation. To cancel this operation, input【N】key and
press 【Enter】 to confirm, or use the keyboard input 【Esc】 to go directly back.
4.5.6.10 RESTORE DEFAUL VALUE
This function allows the user to restore settings to default value, so proceed with caution. To do so, it is
necessary to verify the administrator password. Afterward, input the 【Y】key and press【Enter】 to
confirm the operation. To cancel this operation, input【N】key and press 【Enter】 to confirm, or use the
keyboard input 【Esc】 to go directly back.
4.5.6.11 LOCK CONSOLE
It is not possible to switch or scan after the console has been locked (including switching by pushing a
button on the panel or OSD). The user must enter a password to set.
Note: After locking the console, the user will unlock the console by using this option, which also needs
password verification.（Descriptions of the OSD Menu functions may vary. Refer to the description of
each interface KVM switch manual for details.）
LCD VGA/DVI/Cat5 KVM Switch
27
Appendix
A–1 General Safety Instructions
• This product should only be used indoors.
• Read all the instructions for future reference.
• Follow all the warnings and instructions on the device.
• Do not place this equipment on any unstable surface. If this equipment falls, it will cause serious damage.
• Do not use this equipment near water.
• Do not place this equipment near or over a radiator or other types of heating equipment.
• The enclosure is provided with slots for heat dissipation and ventilation. To prevent overheating during operation, do not block
or cover the openings.
• Do not place the device on a soft surface (such as a bed, sofa, blanket, etc.). This will block proper ventilation. Likewise, do not
place this equipment in a sealed environment unless proper ventilation is provided.
• Do not spray any liquid on the device.
• Before cleaning, unplug the power from the wall socket. Do not use any liquid or foam cleaner. Use a damp cloth to clean it.
• Use this equipment according to the type of power supply on the label. If you are unsure whether the power supply type is
available, contact your dealer or the local power company.
• This equipment is designed for an IT distribution system with 100V ~ 230V phase-to-phase voltage.
• To prevent damage to your device, it is important that all equipment be properly grounded.
• Do not place anything on the power cord or cable. Route the power cord and other cables to avoid tripping over them.
• If the equipment uses an extension cord, make sure that the total capacity of all products using the line does not exceed the
current-carrying capacity of the line. Ensure that the total current of all products plugged into the wall outlet does not exceed
15A.
• Use a surge suppressor, regulator, or uninterruptible power supply (UPS) to help protect your system from sudden, transient,
and reduced power.
• Fix the system cable and power cord properly, and make sure nothing presses on the cable.
• Do not insert objects into the machine through the slots of the housing. There is a risk of exposure to dangerous voltage points
or short-circuiting of parts that could result in fire or electric shock.
• Do not attempt to repair the equipment by yourself. Consult a qualified service person for support.
• If any of the following conditions occur, unplug the unit from the wall outlet and return it to a qualified service representative for
repair.
• The power cord or plug is damaged or worn;
• Liquid is spilled into the unit;
• The device is exposed to rain and water;
• The device has been dropped or the housing has been damaged;
• The function of the device is obviously changed; or,
• The machine canʼt be operated normally as instructed by the operating instructions.
A–2 Cabinet Installation
• Before cabinet installation, make sure that the fixing device is securely fastened to the rack and extended to the ground. The
weight of the whole rack can be dispersed on the floor. Mount the front and side securing devices in a single rack or the front-
end fixtures in combination with multiple racks before starting rack work.
• Install from the bottom up in the cabinet, and install the heaviest things first.
• When extending the equipment from the rack, make sure that the rack is stable.
• Be careful when releasing the latch by pressing the device rails and sliding the unit into the rack. The track of the slide rail may
clip to your finger.
• After mounting the device to the rack, carefully spread the rails to the locked position, and then slide the unit into the rack.
• Do not overload the AC supply branch circuit that supplies power to the rack. The total load capacity of the rack should not
exceed 80% of the branch circuit.
• Make sure that all equipment used on the rack – including electrical outlets and other power connectors – is properly grounded.
• Make sure there is proper airflow to the equipment on the rack.
• Make sure that the operating temperature of the rack environment does not exceed the maximum operating temperature set by
the manufacturer.
• Do not stand on or place undue pressure on any equipment while you are servicing other equipment on the rack.
• WARNING: Slide / rail (LCD / KVM) mounting equipment cannot be used with support brackets or work areas.
✪
LCD VGA/DVI/Cat5 KVM Switch
28
A–3 Specifications
A.3.1 VGA Series LCD KVM Switch
Function
8口
16 口
Connectors
Direct
8
16
Cascade(Max)
128
256
Port Selection
OSD Menu, Front Panel Hot-Key, Hot-key, Remote Control IP
(Optional)
Connectors
Console
Connectors
Video
17”\19”\19”Wide LED Screen
Keyboard
1 x USB Type A Female
Mouse
1 x USB Type A Female
Expansion
Port
1 x USB Type A Female（Prepositive port for keyboard, mouse ）
Computer Port
Monitor,
Keyboard,
Mouse
4 x VGA
DB15bluefe
male
8 x VGA DB15bluefemale
16 x VGA
DB15bluefemale
Power
1 x DC Jack
IP module network port
1 x RJ45
Toggle
Switch
Connection Port Selection
KVM operation panel Numeric buttons
KVM reset
KVM operation panel function buttons
IP Module reset
1 x Semi-embedded keys
IP Module restored initially
1 x Semi-embedded keys
LED
Indicator light
Computer Select port
Two-digit LED display LED
Computer Online port
4 x red
8 x red
16 x red
IP module network port
1 x green 、 1 x orange
Analog Mode
Keyboard Mouse
USB、PS2
Maximum resolution video
1920 x 1200 @ 60HZLocal and remote
Scan time interval
3、5、10、15、20、30、40、60 seconds（default 3 seconds）
Operation
Environment
Operating temperature
0-50℃
Storage temperature
-20-60℃
Humidity
0-80%RH,No condensation
Machine
Attributes
Chassis
Metal
Single slide size
555 x 445 x 45mm
Dual slide size
645 x 443 x 45mm
Weight
16.6KG-18.1KG
LCD VGA/DVI/Cat5 KVM Switch
29
A.3.2 Cat5 Series LCD KVM Switch
Function
8口
16 口
Computer
Connections
Direct
8
16
Cascade(Max)
128
256
Port Selection
OSD Menu, Buttons, Hot-key, Remote Control IP (Optional)
Connector
Console
Connectors
Video
17”\19”\19”wide-screen LCD Monitor
Keyboard
1 x USB Type A Female
Mouse
1 x USB Type A Female
Expansion
Port
1 x USB Type A Female (Prepositive USB port for keyboard, mouse）
Computer
Connectors
Video
keyboard&
mouse
conversion
module
4 x USB
or 4 x PS2
8 x USB
or 8 x PS2
16 x USB
or16 x PS2
Conversion
module port
4 x RJ45
8 x RJ45
16 x RJ45
Power
1 x DC Jack
IP module network port
1 x RJ45
Toggle
switch
Connection Port Selection
KVM operation panel Numeric buttons
KVM reset
KVM operation panel function buttons
IP Module reset
1 x Semi-embedded keys
IP Module restored initially
1 x Semi-embedded keys
LED
Indicator
light
Computer Select port
Two-digit LED display LED
Computer Online port
4 x red
8 x red
16 x red
IP module network port
1 x green 、 1 x orange
Analog
mode
Keyboard Mouse
USB、PS2
Maximum resolution video
1920 x 1200 @ 60HZ local & remote
Scan time interval
3、5、10、15、20、30、40、60 seconds（default 3 seconds）
Operation
Environment
Operating temperature
0-50℃
Storage temperature
-20-60℃
Humidity
0-80%RH,No condensation
Machine
Attributes
Chassis
Metal
Single slide size
555 x 445 x 45mm
Dual slide size
645 x 443 x 45 mm
Weight
16.6KG-18.1KG
LCD VGA/DVI/Cat5 KVM Switch
30
A.3.3 DVI Series LCD KVM Switch
Function
8口
Connectors
Direct
8
Port Selection
OSD Menu, Buttons, hot keys
Connectors
Console
Port
Monitor
17”\19”\19”Wide-Screen LCD Monitor
Keyboard
1 x USB Type A female
Mouse
1 x USB Type A female
Expansion
Port
1 x USB Type A Female (Prepositive port for Keyboard, mouse)
Microphone
4 x Mini Stereo
Female(Pink)
8 x Mini Stereo Female(Pink)
Audio
speakers
4 x Mini Stereo
Female(green)
8 x Mini Stereo Female(green)
Computer
Port
Keyboard,
Mouse
4 x USB Type B
Female
8 x USB Type B Female
Video
4 x DVI-I
8 x DVI-I
Mixed audio
port
4 x Mini Stereo
Female(black)
8 x Mini Stereo Female(black)
Power
1 x DC jack
Toggle switch
Connection Port Selection
KVM operation panel Numeric buttons
KVM reset
KVM operation panel function buttons
LED Indicator
light
Computer Select port
Two-digit LED display LED
Computer Online port
4 x red
8 x red
Analog mode
Keyboard, Mouse
USB Type A
Maximum resolution video
1920 x 1200 @ 60HZ Local
Scan time interval
3、5、10、15、20、30、40、60seconds（default 3 seconds）
Operation
Environment
Operating temperature
0-50℃
Storage temperature
-20-60℃
Humidity
0-80%RH,No condensation
Machine
Attributes
Chassis
Metal
Size
555 x 445 x 45mm
Weight
16.6KG-18.1KG
LCD VGA/DVI/Cat5 KVM Switch
31
A.3.4 LCD Module Specifications
Function
17inchLCD module
19inchLCD module
19inchwide-screen LCD module
LCD
Display
Assembly
LCD Screen
Size Ratio
17inch4:3
19inch4:3
19inch16:9
LCD Screen
Type
SXGA TFT-LCD
Wide AHVA TFT-LCD
Viewing Area
337.920(H) × 270.336(V)
376.32 (H) x 301.056
(V)
408.96(H) x 230.04(V)
Resolution
1280*1024@60HZ
1980*1080@60HZ
Support color
16.7M color（RGB 6 bit + Hi_FRC）
16.7Mcolor,True 8 bit
Contrast
1000 : 1 (Typ)
Backlight
LED
Pixel spacing
0.264x0.297mm
0.294x0.294mm
300*300um
LEDService life
100,000Hours
Nominal Input
Voltage
+5.0V
Keyboard
Keyboard
Layout
Ultra-thin US100 key, Stand alone Removable keyboard. (Keyboard language format
optional)
Compatible
Microsoft Windows9、Me/NT/2000/XP、WIN7、Server2003、 WIN8、WIN10
Port
Standard PS/2;USB （Chocolate keyboard）
Service life
>1,000,000 times
Mouse
Mouse Type
Touch Mouse
Port
Standard PS/2
X/Y resolution
〉1000 point/inch,（40x40/mm)
Service life
>1,000,000 times
LCD VGA/DVI/Cat5 KVM Switch
32
Warranty
ENGLISH: For warranty information, go to intellinetnetwork.com/warranty.
DEUTSCH: Garantieinformationen finden Sie hier unter intellinetnetwork.com/warranty.
ESPAÑOL: Si desea obtener información sobre la garantía, visite intellinetnetwork.com/warranty.
FRANÇAIS: Pour consulter les informations sur la garantie, visitez intellinetnetwork.com/warranty.
POLSKI: Informacje dotyczące gwarancji znajdują się na stronie intellinetnetwork.com/warranty.
ITALIANO: Per informazioni sulla garanzia, accedere a intellinetnetwork.com/warranty.
EN MÉXICO: Póliza de Garantia Intellinet — Datos del importador y responsable ante el
consumidor—IC Intracom México, S.A.P.I. de C.V. Av. Interceptor Poniente # 73, Col. Parque
Industrial La Joya, Cuautitlán Izcalli, Estado de México, C.P. 54730, México. • Tel. (55) 1500-4500
La presente garantía cubre este producto por 3 años contra cualquier defecto de fabricación en sus
materiales y mano de obra, bajo las siguientes condiciones:
Todos los productos a que se refiere esta garantía, ampara su cambio físico, sin ningún cargo para
el consumidor.
El comercializador no tiene talleres de servicio, debido a que los productos que se garantizan no
cuentan con reparaciones, ni refacciones, ya que su garantía es de cambio físico.
La garantía cubre exclusivamente aquellas partes, equipos o sub-ensambles que hayan sido
instaladas de fábrica y no incluye en ningún caso el equipo adicional o cualesquiera que hayan sido
adicionados al mismo por el usuario o distribuidor.
Para hacer efectiva esta garantía bastará con presentar el producto al distribuidor en el domicilio
donde fue adquirido o en el domicilio de IC Intracom México, S.A.P.I. de C.V., junto con los
accesorios contenidos en su empaque, acompañado de su póliza debidamente llenada y sellada por
la casa vendedora (indispensable el sello y fecha de compra) donde lo adquirió, o bien, la factura o
ticket de compra original donde se mencione claramente el modelo, número de serie (cuando
aplique) y fecha de adquisición. Esta garantía no es válida en los siguientes casos: Si el producto se
hubiese utilizado en condiciones distintas a las normales; si el producto no ha sido operado conforme
a los instructivos de uso; o si el producto ha sido alterado o tratado de ser reparado por el
consumidor o terceras personas.
LCD VGA/DVI/Cat5 KVM Switch
33
NOTES
LCD VGA/DVI/Cat5 KVM Switch
34
All trademarks and trade names are the property of their respective owners.
© IC Intracom. All rights reserved. Intellinet is a trademark of IC Intracom, registered in the U.S. and other countries.