Table of Contents
- Contents
- 1. Overview
- Supported Orbi Pro models
- Orbi Pro router and satellite hardware overviews
- LED behavior
- Wall mount or ceiling mount your Orbi Pro router
- Orbi Pro router label and Orbi Pro satellite label
- Connect your Orbi Pro router
- Place your satellite
- Sync your Orbi Pro satellite
- Set up your Orbi network with the NETGEAR Insight app
- 2. Connect to the Orbi Pro Network and Access the Router
- 3. Specify Your Internet Settings
- Use the Internet Setup Wizard
- Manually set up the Internet connection
- Manage an IPv6 Internet connection
- Requirements for entering IPv6 addresses
- Specify IPv6 Internet connections
- Use auto detection for an IPv6 Internet connection
- Use auto configuration for an IPv6 Internet connection
- Set up an IPv6 6rd tunnel Internet connection
- Set up an IPv6 6to4 tunnel Internet connection
- Set up an IPv6 pass-through Internet connection
- Set up an IPv6 fixed Internet connection
- Set up an IPv6 DHCP Internet connection
- Set up an IPv6 PPPoE Internet connection
- Change the MTU size
- 4. Control Access to the Internet
- Manage MAC access control lists for WiFi networks and the LAN
- Manage the Orbi network access control list
- Use keywords to block Internet sites
- Delete keywords that are used to block Internet sites
- Avoid blocking on a trusted computer
- Block services from the Internet
- Schedule when to block Internet sites and services
- Set up security event email notifications
- 5. Specify Network Settings
- View or change WAN settings
- Manage Dynamic DNS
- Set up a default DMZ server
- Change the router’s device name
- Change the LAN TCP/IP settings
- Use the router as a DHCP server
- Disable the DHCP server feature in the router
- Manage reserved LAN IP addresses
- Manage custom static routes
- Change the admin WiFi network settings
- Manage the employee WiFi network settings
- Manage the IoT WiFi network settings
- Set up a guest WiFi network and captive portal
- Manage the download bandwidth per SSID
- View or change advanced WiFi settings
- Use the router as a WiFi access point
- Set up router mode
- Generate a new backhaul password
- Enable or disable implicit beamforming
- Enable or disable MU-MIMO
- Enable or disable Protected Management Frames
- Check your Internet bandwidth
- Set up a bridge for a port group or VLAN tag group
- Improve network connections with Universal Plug and Play
- 6. Manage Your Network
- Update the router and satellite firmware
- Change the admin password
- Enable admin password reset
- Reset the admin password
- View router status and usage information
- Display Internet port statistics
- Check the Internet connection status
- View satellites, WiFi devices, and wired devices connected to the Orbi network
- View satellite status
- View and manage logs of router activity
- Set up a syslog server
- Monitor Internet traffic
- Manage the router configuration file
- Set up remote management
- Use remote access
- 7. Customize Internet Traffic Rules for Ports
- 8. Use VPN to Access Your Network
- 9. Troubleshooting
- A. Supplemental Information
NETGEAR SRK60B04-100EUS User Manual
Displayed below is the user manual for SRK60B04-100EUS by NETGEAR which is a product in the Wireless Routers category. This manual has pages.
Related Manuals
User Manual
Orbi Pro
Models
SRR60
SRS60
NETGEAR, Inc.
350 E. Plumeria DriveMarch 2020
San Jose, CA 95134, USA202-11824-07
Support and Community
Visit netgear.com/support to get your questions answered and access the latest
downloads.
You can also check out our NETGEAR Community for helpful advice at
community.netgear.com.
Regulatory and Legal
Si ce produit est vendu au Canada, vous pouvez accéder à ce document en français
canadien à https://www.netgear.com/support/download/.
(If this product is sold in Canada, you can access this document in Canadian French at
https://www.netgear.com/support/download/.)
For regulatory compliance information including the EU Declaration of Conformity, visit
https://www.netgear.com/about/regulatory/.
See the regulatory compliance document before connecting the power supply.
For NETGEAR’s Privacy Policy, visit https://www.netgear.com/about/privacy-policy.
By using this device, you are agreeing to NETGEAR’s Terms and Conditions at
https://www.netgear.com/about/terms-and-conditions. If you do not agree, return the
device to your place of purchase within your return period.
Trademarks
© NETGEAR, Inc., NETGEAR, and the NETGEAR Logo are trademarks of NETGEAR, Inc.
Any non-NETGEAR trademarks are used for reference purposes only.
2
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Revision History
CommentsPublish DatePublication Part
Number
We added the following sections:
•Enable the network access control list and specify the access rule on page
54 and subsections
•Manage the IoT WiFi network settings on page 87 and subsections
•Set up a guest WiFi network and captive portal on page 90 and Set up a
guest WiFi network with open access or password authentication on page
90
•Enable or disable Protected Management Frames on page 102
•Manage the automatic backup options on page 123
We made major changes to the following sections:
•Manage MAC access control lists for WiFi networks and the LAN on page
48 and subsections
•Change the admin WiFi password or security level on page 81
•Change the employee WiFi password or security level on page 85
•Manage the download bandwidth per SSID on page 95
•View satellites, WiFi devices, and wired devices connected to the Orbi
network on page 117
•View and manage logs of router activity on page 119
•Set up a syslog server on page 120
We made minor changes and adjustments to other sections.
March 2020202-11824-07
We added the following new sections:
•Manage MAC access control lists for WiFi networks and the LAN on page
48
•Manage the download bandwidth per SSID on page 95
•Set up a syslog server on page 120
November 2019202-11824-06
3
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Contents
Chapter 1 Overview
Supported Orbi Pro models..............................................................10
Orbi Pro router and satellite hardware overviews..........................10
Orbi Pro router model SRR60 hardware overview....................10
Orbi Pro satellite model SRS60 hardware overview..................11
LED behavior.......................................................................................11
Orbi Pro WiFi system LEDs...........................................................12
Add-on Orbi Pro satellite LEDs....................................................12
Wall mount or ceiling mount your Orbi Pro router........................13
Wall-mount your Orbi Pro.............................................................13
Ceiling-mount your Orbi Pro........................................................14
Orbi Pro router label and Orbi Pro satellite label..........................16
Connect your Orbi Pro router...........................................................17
Place your satellite..............................................................................18
Sync your Orbi Pro satellite...............................................................18
Sync a satellite from an Orbi Pro WiFi system............................18
Sync an add-on Orbi Pro satellite................................................19
Add satellites to your network using the router web interface.20
Set up your Orbi network with the NETGEAR Insight app............21
Chapter 2 Connect to the Orbi Pro Network and Access the Router
Connect to the network.....................................................................23
Wired connection..........................................................................23
WiFi connection.............................................................................23
WiFi connection using WPS..........................................................24
Types of logins....................................................................................24
Use a web browser to access the router..........................................24
Use the automatic Internet setup option....................................25
Log in to the Orbi router web interface......................................26
Change the language........................................................................27
Chapter 3 Specify Your Internet Settings
Use the Internet Setup Wizard..........................................................29
Manually set up the Internet connection.........................................29
Specify an Internet connection without a login..........................29
Specify an Internet connection that uses a login.......................31
4
Manage an IPv6 Internet connection...............................................33
Requirements for entering IPv6 addresses.................................33
Specify IPv6 Internet connections................................................33
Use auto detection for an IPv6 Internet connection..................34
Use auto configuration for an IPv6 Internet connection...........35
Set up an IPv6 6rd tunnel Internet connection...........................36
Set up an IPv6 6to4 tunnel Internet connection.........................38
Set up an IPv6 pass-through Internet connection......................40
Set up an IPv6 fixed Internet connection....................................40
Set up an IPv6 DHCP Internet connection..................................41
Set up an IPv6 PPPoE Internet connection..................................43
Change the MTU size.........................................................................45
Chapter 4 Control Access to the Internet
Manage MAC access control lists for WiFi networks and the LAN.48
Enable a MAC ACL for a specific network..................................49
Add automatically detected devices to a MAC ACL.................50
Manually add, remove, or change the information for a device
on a MAC ACL................................................................................51
Disable a MAC ACL for a specific network.................................52
Manage the Orbi network access control list..................................53
Enable the network access control list and specify the access
rule...................................................................................................54
Manage the allowed devices on the network access control
list.....................................................................................................55
Manage the blocked devices on the network access control
list.....................................................................................................57
Use keywords to block Internet sites...............................................58
Delete keywords that are used to block Internet sites...................59
Avoid blocking on a trusted computer............................................60
Block services from the Internet.......................................................60
Schedule when to block Internet sites and services......................62
Set up security event email notifications.........................................63
Chapter 5 Specify Network Settings
View or change WAN settings..........................................................66
Manage Dynamic DNS.......................................................................67
Set up a new Dynamic DNS account...........................................67
Specify a DNS account that you already created.......................68
Change the Dynamic DNS settings.............................................69
Set up a default DMZ server..............................................................69
Change the router’s device name....................................................70
Change the LAN TCP/IP settings......................................................71
Use the router as a DHCP server......................................................73
5
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Disable the DHCP server feature in the router...............................74
Manage reserved LAN IP addresses................................................75
Reserve an IP address....................................................................75
Edit a reserved IP address............................................................76
Delete a reserved IP address entry..............................................76
Manage custom static routes............................................................77
Set up a static route.......................................................................77
Edit a static route...........................................................................78
Delete a static route.......................................................................79
Change the admin WiFi network settings.......................................80
Change the admin WiFi network name and channel................80
Change the admin WiFi password or security level..................81
Manage the employee WiFi network settings................................83
Enable the employee WiFi network and change the settings..83
Change the employee WiFi password or security level............85
Manage the IoT WiFi network settings............................................87
Enable the IoT WiFi network and change the settings..............87
Change the IoT WiFi password or security level........................88
Set up a guest WiFi network and captive portal.............................90
Set up a guest WiFi network with open access or password
authentication.................................................................................90
Set up a guest network with a captive portal.............................92
Set up Facebook Wi-Fi..................................................................93
Manage the download bandwidth per SSID...................................95
View or change advanced WiFi settings..........................................97
Use the router as a WiFi access point..............................................98
Set up router mode............................................................................99
Generate a new backhaul password................................................99
Enable or disable implicit beamforming.......................................100
Enable or disable MU-MIMO..........................................................101
Enable or disable Protected Management Frames.....................102
Check your Internet bandwidth......................................................103
Set up a bridge for a port group or VLAN tag group..................103
Set up a bridge for a port group...............................................104
Set up a bridge for a VLAN tag group......................................104
Improve network connections with Universal Plug and Play......106
Chapter 6 Manage Your Network
Update the router and satellite firmware......................................109
Enable the automatic firmware update feature.......................109
Check for firmware updates.......................................................109
Manually update firmware..........................................................110
Manually update satellite firmware...........................................111
Manually update router firmware..............................................111
6
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Change the admin password..........................................................112
Enable admin password reset........................................................113
Reset the admin password..............................................................114
View router status and usage information....................................114
Display Internet port statistics.........................................................115
Check the Internet connection status............................................116
View satellites, WiFi devices, and wired devices connected to the
Orbi network.....................................................................................117
View satellite status..........................................................................118
View and manage logs of router activity.......................................119
Set up a syslog server......................................................................120
Monitor Internet traffic.....................................................................121
Manage the router configuration file.............................................122
Back up settings...........................................................................122
Manage the automatic backup options....................................123
Erase the current configuration settings...................................123
Restore configuration settings...................................................124
Set up remote management...........................................................125
Use remote access...........................................................................126
Chapter 7 Customize Internet Traffic Rules for Ports
Manage port forwarding to a local server.....................................128
Set up port forwarding to a local server...................................128
Add a custom port forwarding service.....................................129
Edit a port forwarding service....................................................130
Delete a port forwarding entry..................................................131
Application example: Make a local web server public...........131
How the router implements the port forwarding rule.............132
Manage port triggering...................................................................132
Add a port triggering service.....................................................133
Enable port triggering................................................................134
Application example: Port triggering for Internet Relay Chat.134
Chapter 8 Use VPN to Access Your Network
Set up a VPN connection.................................................................137
Specify VPN service in the router...................................................137
Install OpenVPN software...............................................................138
Install OpenVPN software on your Windows-based computer.138
Install OpenVPN software on your Mac computer..................141
Install OpenVPN software on an iOS device............................142
Install OpenVPN software on an Android device....................142
Use a VPN tunnel on your Windows-based computer................143
Use VPN to access your Internet service at home........................145
Set up VPN client Internet access in the router........................145
7
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Block VPN client Internet access in the router.........................146
Use a VPN tunnel to access your Internet service at home....147
Chapter 9 Troubleshooting
Quick tips...........................................................................................149
Sequence to restart your network.............................................149
WiFi settings.................................................................................149
Network settings..........................................................................149
The router and satellite do not sync..............................................149
You cannot log in to the router.......................................................151
You cannot access the Internet.......................................................151
Troubleshoot Internet browsing.....................................................152
Troubleshoot PPPoE........................................................................153
Troubleshoot WiFi connectivity......................................................154
Troubleshoot your network using the ping utility........................154
Test the LAN path to your router...............................................154
Test the path from your computer to a remote device...........155
Appendix A Supplemental Information
Factory settings.................................................................................158
Factory settings for Orbi Pro router model SRR60..................158
Factory settings for Orbi Pro satellite model SRS60...............160
Technical specifications...................................................................162
Technical specifications for Orbi Pro router model SRR60....162
Technical specifications for Orbi Pro satellite model SRS60..163
8
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
1
Overview
The Orbi Pro creates dedicated high-speed WiFi connections to your Internet service.
The Orbi Pro router connects to your modem or gateway. The Orbi Pro satellite extends
the WiFi signal throughout your home.
This chapter contains the following sections:
• Supported Orbi Pro models
• Orbi Pro router and satellite hardware overviews
• LED behavior
• Wall mount or ceiling mount your Orbi Pro router
• Orbi Pro router label and Orbi Pro satellite label
• Connect your Orbi Pro router
• Place your satellite
• Sync your Orbi Pro satellite
• Set up your Orbi network with the NETGEAR Insight app
For more information about the topics covered in this manual, visit the support website
at support.netgear.com.
Note: This manual refers to the Orb Pro router as the router and refers to the Orbi Pro
satellite as the satellite.
9
Supported Orbi Pro models
This user manual describes the following Orbi Pro models:
•Orbi Pro Router (Model SRR60)
•Orbi Pro Satellite (Model SRS60)
This user manual does not describe the following Orbi Pro satellites:
•Orbi Outdoor Satellite (Model RBS50Y)
•Orbi Pro Ceiling Satellite (Model SRC60)
For more information about these Orbi Pro satellites, see their user manuals, which are
available at https://www.netgear.com/support/.
Note: To manage your Orbi Pro router and any Orbi Pro satellites that are connected
to your Orbi Pro network, you must manage them from your Orbi Pro router web
interface.
Orbi Pro router and satellite hardware
overviews
The following sections display the hardware features available for the Orbi Pro router
(model SRR60) and Orbi Pro satellite (model SRS60).
Orbi Pro router model SRR60 hardware overview
Figure 1. Orbi Pro router model SRR60, front and back views
User Manual10Overview
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
1. Ring LED (not shown in image)
2. Sync button (also used for WPS connection)
3. Internet port
4. Ethernet ports
5. Power On/Off button and Power LED
6. DC Power connector
7. Reset button
Orbi Pro satellite model SRS60 hardware overview
Figure 2. Orbi Pro satellite model SRS60, front and back views
1. Ring LED (not shown in image)
2. Sync button (also used for WPS connection)
3. Ethernet ports
4. Power On/Off button and Power LED
5. DC Power connector
6. Reset button
LED behavior
When you sync an Orbi Pro satellite to the Orbi Pro router, the LED behavior for a satellite
that comes in an Orbi Pro WiFi system is different from the LED behavior for add-on
Orbi Pro satellites.
User Manual11Overview
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Orbi Pro WiFi system LEDs
The following table describes the LED behavior for an Orbi Pro router (model SRR60)
and Orbi Pro satellite (model SRS60) that are purchased together and come in the same
package.
Table 1. Orbi ProWiFi System router and satellite LED descriptions
LED BehaviorLED
The Power LED is located above the Power On/Off button on the rear panel.
•Solid green. Power is on.
•Solid amber. The router or satellite is booting.
•Blinking amber. The router or satellite is resetting to factory default settings.
•Blinking red. The firmware is corrupted.
•Off. Power is not supplied.
Power LED
The ring LED is located on the top.
•Pulsing white. The router is booting or someone pressed the Sync button.
•Off. The router finished booting and is working normally.
•Solid white. The router is resetting to factory default settings.
•Solid magenta. The router cannot connect to the Internet. See You cannot access the
Internet on page 151.
Router ring LED
This satellite is included when you buy an Orbi router. The ring LED is located on the
top.
•Pulsing white. The satellite is booting.
•Blue for three minutes. The connection between the satellite and the router is good.
•Amber for three minutes. The connection between the satellite and the router is fair.
•Magenta. The satellite failed to sync to the router. See The router and satellite do not
sync on page 149.
•Off. The satellite synced to the router and is working normally.
Satellite ring
LED
Add-on Orbi Pro satellite LEDs
The following table describes the LED behavior for an add-on Orbi Pro satellite (model
SRS60) that was purchased separately from the Orbi Pro kit.
User Manual12Overview
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Table 2. Orbi Pro add-on satellite (model SRS60) LED description
LED BehaviorLED
The Power LED is located above the Power On/Off button on the rear panel.
•Solid green. Power is on.
•Solid amber. The satellite is rebooting.
•Blinking amber. The satellite is resetting to factory default settings.
•Blinking red. The firmware is corrupted.
•Off. Power is not supplied.
Power LED
Optional add-on satellites are sold separately and can be added to your Orbi network. The
ring LED is located on the top.
•Pulsing white. The satellite is booting.
•Solid white. The satellite is ready to sync to the router (press the Sync button).
•Blue for three minutes. The connection between the satellite and the router is good.
•Amber for three minutes. The connection between the satellite and the router is fair.
•Magenta. The satellite is not connected to the router or is not getting an IP address.
•Off. The satellite synced to the router and is working normally.
Add-on satellite
ring LED
Wall mount or ceiling mount your Orbi Pro
router
Your package contains wall-mounting and ceiling-mounting items. Before you can wall
mount or ceiling mount your Orbi Pro router (model SRR60) or Orbi Pro satellite (model
SRS60), you must attach the mount base and cover to your router or satellite.
Wall-mount your Orbi Pro
After you attach the mount base and cover to your router or satellite, you can mount
your router or satellite to the wall.
User Manual13Overview
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
To wall mount your router or satellite:
1. Place your Orbi router or satellite on the mount base and attach the router or satellite
to the base with the provided screws.
2. Attach the mount cover to the mount base.
3. Use the wall anchors with screws to attach the wall bracket to the wall.
4. Slide the mount base onto the wall bracket.
Ceiling-mount your Orbi Pro
The following instructions require a drop ceiling.
User Manual14Overview
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
To ceiling mount your router or satellite:
1. Place your Orbi router or satellite on the mount base and attach the router or satellite
to the base with the provided screws.
2. Attach the mount cover to the mount base.
3. Attach the T-bracket to the ceiling bracket with the T-bracket screws.
4. Loosen the screw so that the locking plate can slide.
5. Secure the T-bracket to the T-bar and tighten the screw.
User Manual15Overview
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
6. Slide the mount base into the ceiling bracket.
Orbi Pro router label and Orbi Pro satellite
label
The Orbi Pro router label shows the login information, the WiFi network name and
password, the router’s MAC address, and the router’s serial number. The following is
an example of what the router label might look like:
Figure 3. Orbi Pro router label
The Orbi Pro satellite label shows the WiFi network name and password, the satellite’s
MAC address, and the satellite’s serial number. The following is an example of what the
satellite label might look like:
User Manual16Overview
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Figure 4. Orbi Pro satellite label
Connect your Orbi Pro router
If you want to connect your Orbi Pro router to an existing gateway, we recommend that
you turn off your existing gateway’s WiFi.
To cable your router:
1. Unplug your modem’s power, leaving the modem connected to the wall jack for
your Internet service.
If your modem uses a battery backup, remove the battery, and then put the battery
back in.
2. Plug in and turn on your modem.
3. Connect your modem to the Internet port of your router with the Ethernet cable that
came with your router.
4. Connect the power adapter to your router and plug the power adapter into an
outlet.
5. If the Power LED does not light, press the Power On/Off button on the rear panel
of the router.
User Manual17Overview
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Place your satellite
Your satellites must be within range of your router’s WiFi signal in order for it to sync
with the router. Use the satellite’s ring LED to help you determine where to place your
satellite.
Sync your Orbi Pro satellite
The sync process for your Orbi Pro satellite depends on whether your satellite came
with your Orbi Pro WiFi system, or if your satellite is an add-on satellite.
Sync a satellite from an Orbi Pro WiFi system
The Orbi Pro WiFi System includes an Orbi Pro router and a Orbi Pro satellite. The Orbi
pro satellite in the WiFi system is preset to automatically find and sync to the WiFi signal
from the Orbi Pro router in the same WiFi system.
To sync your Orbi Pro satellite:
1. Place your satellite.
For more information, see Place your satellite on page 18.
2. Connect the satellite to a power source.
3. If the Power LED on the back of the satellite does not light, press the Power On/Off
button.
The satellite ring LED pulses white. The satellite automatically finds the Orbi router’s
WiFi signal and attempts to sync to the Orbi router.
The satellite ring LED lights one of the following colors for about three minutes and
then turns off:
•Blue. The Orbi router and satellite successfully synced, and the connection
between the router and satellite is good.
•Amber. The Orbi router and satellite successfully synced, and the connection
between the router and satellite is fair. Consider moving the Orbi satellite closer
to the Orbi router.
•Magenta. The Orbi router and satellite failed to sync.
User Manual18Overview
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
4. If the satellite ring LED is magenta, move the satellite closer to the router and then
sync the satellite to the router:
a. Press the Sync button on the back of the router.
b. Within two minutes, press the Sync button on the back of the satellite.
The satellite attempts to sync to the Orbi router. The satellite ring LED lights blue,
amber, or magenta as described in Step 3 of this procedure and then turns off.
Sync an add-on Orbi Pro satellite
If you already set up an Orbi Pro router and satellite are adding an optional add-on Orbi
Pro satellite (sold separately), follow these steps.
To sync your add-on Orbi Pro satellite:
1. Place your satellite.
For more information, see Place your satellite on page 18.
2. Connect the satellite to a power source.
3. If the Power LED on the back of the satellite does not light, press the Power On/Off
button.
4. Wait about two minutes for the satellite ring LED to light solid white.
5. Press the Sync button on the back of the satellite and within two minutes, press the
Sync button on the back of your Orbi router.
The satellite ring LED pulses white, then lights one of the following colors for about
three minutes, and then turns off:
•Blue. The Orbi router and satellite successfully synced, and the connection
between the router and satellite is good.
•Amber. The Orbi router and satellite successfully synced, and the connection
between the router and satellite is fair. Consider moving the Orbi satellite closer
to the Orbi router.
•Magenta. The Orbi router and satellite failed to sync. Move the satellite closer
to the router and try again.
User Manual19Overview
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Add satellites to your network using the router web interface
You can use the router web interface to add a satellite to your Orbi network.
To add a satellite to your Orbi network using the router web interface:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the router admin user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home page displays.
4. Select Add Orbi Satellite.
The Place Your Satellite page displays.
5. Follow the instructions about where to place your satellite in your house.
6. Connect the satellite to a power source.
7. If the Power LED on the back of the satellite does not light, press the Power On/Off
button.
8. Click the NEXT button.
9. Wait about two minutes for the satellite’s ring LED to light solid white.
10. Press the Sync button on the satellite.
The satellite’s ring LED pulses white.
11. Click the SYNC button in the router web interface.
The router attempts to sync with the satellite.
The satellite’s ring LED lights one of the following colors for about three minutes
and then turns off:
•Blue. The Orbi router and satellite successfully synced, and the connection
between the router and satellite is good.
•Amber. The Orbi router and satellite successfully synced, and the connection
between the router and satellite is fair. Consider moving the Orbi satellite closer
to the Orbi router.
•Magenta. The Orbi router and satellite failed to sync. Move the satellite closer
to the router and try again.
User Manual20Overview
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Set up your Orbi network with the NETGEAR
Insight app
You can use the NETGEAR Insight app to set up your Orbi network.
To find the app, search for NETGEAR Insight in the Apple App Store or Google Play
Store. Then launch the NETGEAR Insight app on your mobile device and follow the
prompts. For more information about the NETGEAR Insight app, visit
https://www.netgear.com/insight/.
User Manual21Overview
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
2
Connect to the Orbi Pro Network
and Access the Router
To manage your Orbi Pro router and any Orbi Pro satellites that are connected to your
Orbi Pro network, you must manage them from your Orbi Pro router web interface.
This chapter contains the following sections:
• Connect to the network
• Types of logins
• Use a web browser to access the router
• Change the language
22
Connect to the network
You can connect to the Orbi network through a wired or WiFi connection. If you set up
your computer to use a static IP address, change the settings so that it uses Dynamic
Host Configuration Protocol (DHCP).
Wired connection
You can connect your computer to the router using an Ethernet cable and join the
router’s local area network (LAN).
To connect your computer to the router with an Ethernet cable:
1. Make sure that the router is receiving power (its Power LED is lit).
2. Connect an Ethernet cable to an Ethernet port on your computer.
3. Connect the other end of the Ethernet cable to one of the router’s Ethernet ports.
Your computer connects to the local area network (LAN). A message might display
on your computer screen to notify you that an Ethernet cable is connected.
WiFi connection
If you're installing your Orbi router for the first time, you can connect to the router's
WiFi network by scanning the QR code on your router with the camera app on your
mobile device. To scan the QR code with your camera app, your mobile device must
have iOS version 11 or later or Android version 10 or later.
You can also manually find and select the Orbi router's WiFi network from your
WiFi-enabled computer or mobile device.
To find and select the WiFi network:
1. Make sure that the router or satellite is receiving power (its Power LED is lit).
2. On your WiFi-enabled computer or mobile device, find and select the WiFi network.
The WiFi network name is on the router label. The WiFi network name is the same
for the router and the satellite in the Orbi WiFi System.
Note: If you bought the router and the satellite separately, their default WiFi network
names are different.
3. Join the WiFi network and enter the WiFi password.
The password is on the router label.
Your WiFi-enabled computer or mobile device connects to the WiFi network.
User Manual23Connect to the Orbi Pro Network
and Access the Router
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
WiFi connection using WPS
You can connect to the router’s WiFi network with Wi-Fi Protected Setup (WPS) or you
can find and select the WiFi network.
To use WPS to connect to the WiFi network:
1. Make sure that the router is receiving power (its Power LED is lit).
2. Check the WPS instructions for your computer or WiFi device.
3. Press the Sync button on the router.
4. Within two minutes, on your WiFi-enabled computer or mobile device, press its WPS
button or follow its instructions for WPS connections.
Your computer or mobile device connects to the WiFi network.
Types of logins
Separate types of logins serve different purposes. It is important that you understand
the difference so that you know which login to use when.
Types of logins:
•Internet service login. The login that your Internet service provider (ISP) gave you
logs you in to your Internet service. Your service provider gave you this login
information in a letter or some other way. If you cannot find this login information,
contact your service provider.
•WiFi network key or password. Your router and satellite are preset with the same
WiFi network name (SSID) and password for WiFi access. This information is on the
router label and the satellite label.
•Router login. This logs you in to the router interface from a web browser as admin.
Use a web browser to access the router
When you connect to the network (either with WiFi or with an Ethernet cable), you can
use a web browser to access the router to view or change its settings. The first time you
access the router, the NETGEAR installation assistant automatically checks to see if your
router can connect to your Internet service.
User Manual24Connect to the Orbi Pro Network
and Access the Router
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Use the automatic Internet setup option
You can set up your router automatically, or you can use a web browser to access the
router and set up your router manually. Before you start the setup process, get your ISP
information and make sure that the computers and devices in the network use the
settings described here.
When your Internet service starts, your Internet service provider (ISP) typically gives you
all the information needed to connect to the Internet. For DSL service, you might need
the following information to set up your router:
•The ISP configuration information for your DSL account
•ISP login name and password
•Fixed or static IP address settings (special deployment by ISP; this setting is rare)
If you cannot locate this information, ask your ISP to provide it. When your Internet
connection is working, you no longer need to launch the ISP login program on your
computer to access the Internet. When you start an Internet application, your router
automatically logs you in.
Installation and basic setup takes about 15 minutes to complete.
To automatically set up your router:
1. Power on your router.
2. Make sure that your WiFi-enabled computer or mobile device is connected to the
router with an Ethernet cable (wired) or wirelessly with the preset security settings
listed on the label.
Note: If you want to change the router’s WiFi settings, use a wired connection to
avoid being disconnected when the new WiFi settings take effect.
3. Launch a web browser.
The page that displays depends on whether you accessed the router before:
•The first time that you set up the Internet connection for your router, the browser
goes to orbilogin.com, and the Orbi login page displays.
•If you already set up the Internet connection, enter orbilogin.com in the address
field for your browser to start the installation process.
4. Follow the onscreen instructions.
The router connects to the Internet.
User Manual25Connect to the Orbi Pro Network
and Access the Router
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
5. If the browser does not display the web page, do the following:
•Make sure that the computer is connected to one of the four LAN Ethernet ports
or over WiFi to the router.
•Make sure that the router is receiving power, and that its Power LED is lit.
•Close and reopen the browser or clear the browser cache.
•Browse to orbilogin.com.
•If the computer is set to a static or fixed IP address (this setting is uncommon),
change it to obtain an IP address automatically from the router.
6. If the router does not connect to the Internet, do the following:
a. Review your settings.
b. Make sure that you selected the correct options and typed everything correctly.
c. Contact your ISP to verify that you are using the correct configuration information.
d. Read Troubleshooting on page 148.
If problems persist, register your NETGEAR product and contact NETGEAR
technical support.
Log in to the Orbi router web interface
When you log in to the Orbi, the browser displays the router web interface. You can
use the router web interface to change the router or satellite settings.
To log in to your Orbi:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the router admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
User Manual26Connect to the Orbi Pro Network
and Access the Router
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Change the language
By default, the language is set as Auto.
To change the language:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the router admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. In the upper right corner, select a language from the menu.
5. When prompted, click the OK button to confirm this change.
The page refreshes with the language that you selected.
User Manual27Connect to the Orbi Pro Network
and Access the Router
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
3
Specify Your Internet Settings
Usually, the quickest way to set up the router to use your Internet connection is to allow
Orbi to detect the Internet connection when you first access the router with a web
browser. You can also customize or specify your Internet settings.
This chapter contains the following sections:
• Use the Internet Setup Wizard
• Manually set up the Internet connection
• Manage an IPv6 Internet connection
• Change the MTU size
28
Use the Internet Setup Wizard
You can use the Setup Wizard to detect your Internet settings and automatically set up
your router.
To use the Setup Wizard:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Setup Wizard.
The Setup Wizard page displays.
5. Select the Yes radio button.
If you select No, you are taken to the Internet Setup page (see Manually set up the
Internet connection on page 29).
6. Click the Next button.
The Setup Wizard searches your Internet connection for servers and protocols to
determine your ISP configuration and checks your operation mode.
Manually set up the Internet connection
You can view or change the router’s Internet connection settings.
Specify an Internet connection without a login
To specify the Internet connection settings:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
User Manual29Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Internet.
The Internet Setup page.
5. Leave the Does your Internet connection require a login No radio button selected.
6. If your Internet connection requires an account name or host name, type it in the
Account Name (If Required) field.
7. If your Internet connection requires a domain name, type it in the Domain Name (If
Required) field.
For the other sections in this page, the default settings usually work, but you can
change them.
8. Select an Internet IP Address radio button:
•Get Dynamically from ISP. Your ISP uses DHCP to assign your IP address. Your
ISP automatically assigns these addresses.
•Use Static IP Address. Enter the IP address, IP subnet mask, and the gateway IP
address that your ISP assigned. The gateway is the ISP router to which your router
connects.
9. Select a Domain Name Server (DNS) Address radio button:
•Get Automatically from ISP. Your ISP uses DHCP to assign your DNS servers.
Your ISP automatically assigns this address.
•Use These DNS Servers. If you know that your ISP requires specific servers, select
this option. Enter the IP address of your ISP’s primary DNS server. If a secondary
DNS server address is available, enter it also.
10. Select a Router MAC Address radio button:
•Use Default Address. Use the default MAC address.
•Use Computer MAC Address. The router captures and uses the MAC address
of the computer that you are now using. You must use the one computer that the
ISP allows.
•Use This MAC Address. Enter the MAC address that you want to use.
11. Click the Apply button.
Your settings are saved.
User Manual30Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
12. Click the Test button to test your Internet connection.
Specify an Internet connection that uses a login
To view or change the basic Internet setup:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Internet.
The Internet Setup page displays.
5. Select the Does your Internet connection require a login Yes radio button.
The page adjusts.
6. From the Internet Service Provider menu, select the encapsulation method:
The selections are PPPoE,PPTP,orL2TP.
7. In the Login field, enter the login name your ISP gave you.
This login name is often an email address.
8. In the Password field, type the password that you use to log in to your Internet
service.
9. If your ISP requires a service name, type it in the Service Name (if Required) field.
10. From the Connection Mode menu, select Always On,Dial on Demand,orManually
Connect.
11. To change the number of minutes until the Internet login time out, in the Idle Timeout
(In minutes) field, type the number of minutes.
This is how long the router keeps the Internet connection active when no one on the
network is using the Internet connection. A value of 0 (zero) means never log out.
User Manual31Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
12. Select an Internet IP Address radio button:
•Get Dynamically from ISP. Your ISP uses DHCP to assign your IP address. Your
ISP automatically assigns these addresses.
•Use Static IP Address. Enter the IP address, IP subnet mask, and gateway IP
address that your ISP assigned. The gateway is the ISP router to which your router
connects.
13. Select a Domain Name Server (DNS) radio button:
•Get Automatically from ISP. Your ISP uses DHCP to assign your DNS servers.
Your ISP automatically assigns this address.
•Use These DNS Servers. If you know that your ISP requires specific servers, select
this option. Enter the IP address of your ISP’s primary DNS server. If a secondary
DNS server address is available, enter it also.
14. Select a Router MAC Address radio button:
•Use Default Address. Use the default MAC address.
•Use Computer MAC Address. The router captures and uses the MAC address
of the computer that you are now using. You must use the one computer that the
ISP allows.
•Use This MAC Address. Enter the MAC address that you want to use.
15. Click the Apply button.
Your settings are saved.
16. Click the Test button to test your Internet connection.
User Manual32Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Manage an IPv6 Internet connection
The router supports many different types of IPv6 Internet connections for which you can
specify the settings manually.
Requirements for entering IPv6 addresses
IPv6 addresses are denoted by eight groups of hexadecimal quartets that are separated
by colons. You can reduce any four-digit group of zeros within an IPv6 address to a
single zero or omit it. The following errors invalidate an IPv6 address:
•More than eight groups of hexadecimal quartets
•More than four hexadecimal characters in a quartet
•More than two colons in a row
Specify IPv6 Internet connections
You can set up an IPv6 Internet connection if the router does not detect it automatically.
To set up an IPv6 Internet connection:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > IPv6.
The IPv6 page displays.
5. From the Internet Connection Type menu, select the IPv6 connection type:
•If you are not sure, select Auto Detect so that the router detects the IPv6 type
that is in use.
•If your Internet connection does not use PPPoE, DHCP, or fixed, but is IPv6, select
Auto Config.
Your Internet service provider (ISP) can provide this information. For more
information about IPv6 Internet connection, see the following sections:
User Manual33Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
•Use auto detection for an IPv6 Internet connection on page 34
•Use auto configuration for an IPv6 Internet connection on page 35
•Set up an IPv6 6rd tunnel Internet connection on page 36
•Set up an IPv6 6to4 tunnel Internet connection on page 38
•Set up an IPv6 pass-through Internet connection on page 40
•Set up an IPv6 fixed Internet connection on page 40
•Set up an IPv6 DHCP Internet connection on page 41
•Set up an IPv6 PPPoE Internet connection on page 43
6. Click the Apply button.
Your settings are saved.
Use auto detection for an IPv6 Internet connection
To set up an IPv6 Internet connection through auto detection:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > IPv6.
The IPv6 page displays.
5. From the Internet Connection Type menu, select Auto Detect.
The page adjusts.
The router automatically detects the information in the following fields:
•Connection Type. This field indicates the connection type that is detected.
•Router’s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the router’s WAN (or Internet) interface. The number after the slash (/) is the
User Manual34Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
length of the prefix, which is also indicated by the underline (_) under the IPv6
address. If no address is acquired, the field displays Not Available.
•Router’s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the router’s LAN interface. The number after the slash (/) is the length of the
prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
6. Select an IP Address Assignment radio button:
•Use DHCP Server. This method passes more information to LAN devices, but
some IPv6 systems might not support the DHCv6 client function.
•Auto Config. This is the default setting.
This setting specifies how the router assigns IPv6 addresses to the devices on your
home network (the LAN).
7. (Optional) Select the Use This Interface ID check box and specify the interface ID
to be used for the IPv6 address of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
8. Click the Apply button.
Your settings are saved.
Use auto configuration for an IPv6 Internet connection
To set up an IPv6 Internet connection through auto configuration:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > IPv6.
The IPv6 page displays.
5. From the Internet Connection Type menu, select Auto Config.
The page adjusts.
User Manual35Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
The router automatically detects the information in the following fields:
•Router’s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the router’s WAN (or Internet) interface. The number after the slash (/) is the
length of the prefix, which is also indicated by the underline (_) under the IPv6
address. If no address is acquired, the field displays Not Available.
•Router’s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the router’s LAN interface. The number after the slash (/) is the length of the
prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
6. (Optional) In the DHCP User Class (If Required) field, enter a host name.
Most people can leave this field blank, but if your ISP gave you a specific host name,
enter it here.
7. (Optional) In the DHCP Domain Name (If Required) field, enter a domain name.
You can type the domain name of your IPv6 ISP. Do not enter the domain name for
the IPv4 ISP here. For example, if your ISP’s mail server is mail.xxx.yyy.zzz, type
xxx.yyy.zzz as the domain name. If your ISP provided a domain name, type it in this
field. For example, Earthlink Cable might require a host name of home, and Comcast
sometimes supplies a domain name.
8. Select an IP Address Assignment radio button:
•Use DHCP Server. This method passes more information to LAN devices, but
some IPv6 systems might not support the DHCv6 client function.
•Auto Config. This is the default setting.
9. (Optional) Select the Use This Interface ID check box and specify the interface ID
that you want to be used for the IPv6 address of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
10. Click the Apply button.
Your settings are saved.
Set up an IPv6 6rd tunnel Internet connection
The 6rd protocol makes it possible to deploy IPv6 to sites using a service provider’s
IPv4 network. 6rd uses the service provider’s own IPv6 address prefix. This limits the
operational domain of 6rd to the service provider’s network and is under direct control
of the service provider. The IPv6 service provided is equivalent to native IPv6. The 6rd
mechanism relies on an algorithmic mapping between the IPv6 and IPv4 addresses that
User Manual36Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
are assigned for use within the service provider’s network. This mapping allows for
automatic determination of IPv4 tunnel endpoints from IPv6 prefixes, allowing stateless
operation of 6rd.
With a 6rd Tunnel configuration, the router follows the RFC5969 standard, supporting
two ways to establish a 6rd tunnel IPv6 WAN connection:
•Auto Detect Mode. In IPv6 Auto Detect mode, when the router receives option 212
from the DHCPv4 option, auto detect selects the IPv6 as 6rd Tunnel setting. The
router uses the 6rd option information to establish the 6rd connection.
•Manual Mode. Select 6rd. If the router receives option 212, the fields are
automatically completed. Otherwise, you must enter the 6rd settings.
To set up an IPv6 6rd Tunnel Internet connection:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > IPv6.
The IPv6 page displays.
5. In the Internet Connection Type menu, select 6rd.
The page adjusts.
The router automatically detects the information in the following sections:
•6rd (IPv6 Rapid Development) Configuration. The router detects the service
provider’s IPv4 network and attempts to establish an IPv6 6rd Tunnel connection.
If the IPv4 network returns 6rd parameters to the router, the page adjusts to
display the correct settings in this section.
•Router’s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the router’s LAN interface. The number after the slash (/) is the length of the
prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
User Manual37Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
6. Select an IPv6 Domain Name Server (DNS) Address radio button:
•Get Automatically from ISP. Your ISP uses DHCP to assign your DNS servers.
Your ISP automatically assigns this address.
•Use These DNS Servers. If you know that your ISP requires specific servers, select
this option. Enter the IP address of your ISP’s primary DNS server. If a secondary
DNS server address is available, enter it also.
7. Select an IP Address Assignment radio button:
•Use DHCP Server. This method passes more information to LAN devices, but
some IPv6 systems might not support the DHCv6 client function.
•Auto Config. This is the default setting.
This setting specifies how the router assigns IPv6 addresses to the devices on your
home network.
8. (Optional) Select the Use This Interface ID check box and specify the interface ID
that you want to be used for the IPv6 address of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
9. Click the Apply button.
Your settings are saved.
Set up an IPv6 6to4 tunnel Internet connection
The remote relay router is the router to which your router creates a 6to4 tunnel. Make
sure that the IPv4 Internet connection is working before you apply the 6to4 tunnel
settings for the IPv6 connection.
To set up an IPv6 Internet connection by using a 6to4 tunnel:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > IPv6.
User Manual38Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
The IPv6 page displays.
5. From the Internet Connection Type menu, select 6to4 Tunnel.
The page adjusts.
The router automatically detects the information in the Router’s IPv6 Address on
LAN field. This field shows the IPv6 address that is acquired for the router’s LAN
interface. The number after the slash (/) is the length of the prefix, which is also
indicated by the underline (_) under the IPv6 address. If no address is acquired, the
field displays Not Available.
6. Select a Remote 6to4 Relay Router radio button:
•Auto. Your router uses any remote relay router that is available on the Internet.
This is the default setting.
•Static IP Address. Enter the static IPv4 address of the remote relay router. Your
IPv6 ISP usually provides this address.
7. Select an IPv6 Domain Name Server (DNS Address) radio button:
•Get Automatically from ISP. Your ISP uses DHCP to assign your DNS servers.
Your ISP automatically assigns this address.
•Use These DNS Servers. If you know that your ISP requires specific servers, select
this option. Enter the IP address of your ISP’s primary DNS server. If a secondary
DNS server address is available, enter it also.
8. Select an IP Address Assignment radio button:
•Use DHCP Server. This method passes more information to LAN devices, but
some IPv6 systems might not support the DHCv6 client function.
•Auto Config. This is the default setting.
This setting specifies how the router assigns IPv6 addresses to the devices on your
home network.
9. (Optional) Select the Use This Interface ID check box and specify the interface ID
that you want to be used for the IPv6 address of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
10. Click the Apply button.
Your settings are saved.
User Manual39Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Set up an IPv6 pass-through Internet connection
In pass-through mode, the router works as a Layer 2 Ethernet switch with two ports (LAN
and WAN Ethernet ports) for IPv6 packets. The router does not process any IPv6 header
packets.
To set up a pass-through IPv6 Internet connection:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > IPv6.
The IPv6 page displays.
5. From the Internet Connection Type menu, select Pass Through.
The page adjusts, but no additional fields display.
6. Click the Apply button.
Your settings are saved.
Set up an IPv6 fixed Internet connection
To set up a fixed IPv6 Internet connection:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > IPv6.
The IPv6 page displays.
User Manual40Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
5. From the Internet Connection Type menu, select Fixed.
The page adjusts.
6. Configure the fixed IPv6 addresses for the WAN connection:
•IPv6 Address/Prefix Length. The IPv6 address and prefix length of the router
WAN interface.
•Default IPv6 Gateway. The IPv6 address of the default IPv6 gateway for the
router’s WAN interface.
•Primary DNS Server. The primary DNS server that resolves IPv6 domain name
records for the router.
•Secondary DNS Server. The secondary DNS server that resolves IPv6 domain
name records for the router.
Note: If you do not specify the DNS servers, the router uses the DNS servers that
are configured for the IPv4 Internet connection on the Internet Setup page. (See
Manually set up the Internet connection on page 29.)
7. Select an IP Address Assignment radio button:
•Use DHCP Server. This method passes more information to LAN devices, but
some IPv6 systems might not support the DHCv6 client function.
•Auto Config. This is the default setting.
This setting specifies how the router assigns IPv6 addresses to the devices on your
home network.
8. In the IPv6 Address/Prefix Length fields, specify the static IPv6 address and prefix
length of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
9. Click the Apply button.
Your settings are saved.
Set up an IPv6 DHCP Internet connection
To set up an IPv6 Internet connection with a DHCP server:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
User Manual41Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > IPv6.
The IPv6 page displays.
5. From the Internet Connection Type menu, select DHCP.
The page adjusts.
The router automatically detects the information in the following fields:
•Router’s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the router’s WAN (or Internet) interface. The number after the slash (/) is the
length of the prefix, which is also indicated by the underline (_) under the IPv6
address. If no address is acquired, the field displays Not Available.
•Router’s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the router’s LAN interface. The number after the slash (/) is the length of the
prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
6. Select an IPv6 Domain Name Server (DNS) Address radio button:
•Get Automatically from ISP. Your ISP uses DHCP to assign your DNS servers.
Your ISP automatically assigns this address.
•Use These DNS Servers. If you know that your ISP requires specific servers, select
this option. Enter the IP address of your ISP’s primary DNS server. If a secondary
DNS server address is available, enter it also.
7. (Optional) In the User Class (If Required) field, enter a host name.
Most people can leave this field blank, but if your ISP gave you a specific host name,
enter it here.
8. (Optional) In the Domain Name (If Required) field, enter a domain name.
You can type the domain name of your IPv6 ISP. Do not enter the domain name for
the IPv4 ISP here. For example, if your ISP’s mail server is mail.xxx.yyy.zzz, type
xxx.yyy.zzz as the domain name. If your ISP provided a domain name, type it in this
field. For example, Earthlink Cable might require a host name of home, and Comcast
sometimes supplies a domain name.
User Manual42Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
9. Select an IP Address Assignment radio button:
•Use DHCP Server. This method passes more information to LAN devices, but
some IPv6 systems might not support the DHCv6 client function.
•Auto Config. This is the default setting.
This setting specifies how the router assigns IPv6 addresses to the devices on your
home network (the LAN).
10. (Optional) Select the Use This Interface ID check box and specify the interface ID
that you want to be used for the IPv6 address of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
11. Click the Apply button.
Your settings are saved.
Set up an IPv6 PPPoE Internet connection
To set up a PPPoE IPv6 Internet connection:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > IPv6.
The IPv6 page displays.
5. From the Internet Connection Type menu, select PPPoE.
The page adjusts.
The router automatically detects the information in the following fields:
•Router’s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the router’s WAN (or Internet) interface. The number after the slash (/) is the
User Manual43Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
length of the prefix, which is also indicated by the underline (_) under the IPv6
address. If no address is acquired, the field displays Not Available.
•Router’s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the router’s LAN interface. The number after the slash (/) is the length of the
prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
6. In the Login field, enter the login information for the ISP connection.
This is usually the name that you use in your email address. For example, if your main
mail account is JerAB@ISP.com, you would type JerAB in this field. Some ISPs (like
Mindspring, Earthlink, and T-DSL) require that you use your full email address when
you log in. If your ISP requires your full email address, type it in this field.
7. In the Password field, enter the password for the ISP connection.
8. In the Service Name field, enter a service name.
If your ISP did not provide a service name, leave this field blank.
Note: The default setting of the Connection Mode field is Always On to provide a
steady IPv6 connection. The router never terminates the connection. If the connection
is terminated, for example, when the modem is turned off, the router attempts to
reestablish the connection immediately after the PPPoE connection becomes available
again.
9. Select an IPv6 Domain Name Server (DNS) Address radio button:
•Get Automatically from ISP. Your ISP uses DHCP to assign your DNS servers.
Your ISP automatically assigns this address.
•Use These DNS Servers. If you know that your ISP requires specific servers, select
this option. Enter the IP address of your ISP’s primary DNS server. If a secondary
DNS server address is available, enter it also.
10. (Optional) Select the Use This Interface ID check box and specify the interface ID
that you want to be used for the IPv6 address of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
11. Click the Apply button.
Your settings are saved.
User Manual44Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Change the MTU size
The maximum transmission unit (MTU) is the largest data packet a network device
transmits. When one network device communicates across the Internet with another,
the data packets travel through many devices along the way. If a device in the data path
uses a lower MTU setting than the other devices, the data packets must be split or
“fragmented” to accommodate the device with the smallest MTU.
The best MTU setting for NETGEAR equipment is often the default value. In some
situations, changing the value fixes one problem but causes another. Leave the MTU
unchanged unless one of these situations occurs:
•You experience problems connecting to your ISP or other Internet service, and the
technical support of either the ISP or NETGEAR recommends changing the MTU
setting. These web-based applications might require an MTU change:
-A secure website that does not open, or displays only part of a web page
- Yahoo email
- MSN portal
•You use VPN and experience severe performance problems.
•You used a program to optimize MTU for performance reasons, and now you are
experiencing connectivity or performance problems.
Note: An incorrect MTU setting can cause Internet communication problems. For
example, you might not be able to access certain websites, frames within websites,
secure login pages, or FTP or POP servers.
To change the MTU size:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Setup > WAN Setup.
The WAN Setup page displays.
User Manual45Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
5. In the MTU Size field, enter a value from 64 to 1500.
6. Click the Apply button.
Your settings are saved.
If you suspect an MTU problem, a common solution is to change the MTU to 1400.
If you are willing to experiment, you can gradually reduce the MTU from the maximum
value of 1500 until the problem goes away. The following table describes common
MTU sizes and applications.
Table 3. Common MTU sizes
ApplicationMTU
The largest Ethernet packet size. This setting is typical for connections that do not use PPPoE or VPN,
and is the default value for NETGEAR routers, adapters, and switches.
1500
Used in PPPoE environments.1492
Maximum size to use for pinging. (Larger packets are fragmented.)1472
Used in some DHCP environments.1468
Used in PPTP environments or with VPN.1436
Typical value to connect to dial-up ISPs.576
User Manual46Specify Your Internet Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
4
Control Access to the Internet
The router comes with a built-in firewall that helps protect your home network from
unwanted intrusions from the Internet.
This chapter includes the following sections:
• Manage MAC access control lists for WiFi networks and the LAN
• Manage the Orbi network access control list
• Use keywords to block Internet sites
• Delete keywords that are used to block Internet sites
• Avoid blocking on a trusted computer
• Block services from the Internet
• Schedule when to block Internet sites and services
• Set up security event email notifications
47
Manage MAC access control lists for WiFi
networks and the LAN
A MAC access control list (ACL) for a WiFi network (that is, an SSID) or the wired network
(that is, the LAN) allows or denies a device access to the network based only on the
MAC address of the device. If you block a device for one WiFi network or for the wired
network, the device is blocked only for that WiFi network or for the wired network. You
can set up an independent MAC ACL for each WiFi network and for the wired network.
(The router supports a total of five MAC ACLs.) With a MAC ACL, you can allow or deny
access to a device on a specific WiFi network or the wired network.
Note: A MAC ACL differs from the network access control list (see Manage the Orbi
network access control list on page 53). The network access control list is not specific
to a particular WiFi network or to the wired network but is based on both WiFi and wired
devices that the router detects on the entire Orbi network. To allow or deny access to
a device on a specific WiFi network or the wired network, use a MAC ACL. MAC ACLs
and the network access control list are mutually exclusive. Use either MAC ACLs or the
network access control list.
If you set up a MAC ACL with a policy that allows access to a specific network, devices
on the MAC ACL are an exception to the default policy:
•A device for which you place the MAC address on the MAC ACL is denied access to
that network.
•All other devices are allowed access to that network.
If you set up a MAC ACL with a policy that denies access to a specific network, devices
on the MAC ACL are an exception to the default policy:
•A device for which you place the MAC address on the MAC ACL is allowed access
to that work.
•All other devices are denied access to that network.
A blocked device can still get an IP address from the router but cannot communicate
with other devices on the network or connect to the Internet.
Note: Each network device owns a MAC address, which is a unique 12-character physical
address, containing the hexadecimal characters 0–9, a–f, or A–F (uppercase or lowercase)
only, and separated by colons (for example, 00:09:AB:CD:EF:01). Typically, the MAC
address is on the label of a device. If you cannot see the label, you can display the MAC
address using the network configuration utilities of a computer. You might also find the
MAC addresses on Attached Devices page of the router (see View satellites, WiFi devices,
and wired devices connected to the Orbi network on page 117).
User Manual48Control Access to the Internet
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Enable a MAC ACL for a specific network
When you enable a MAC ACL for a specific network, you must specify the default policy
for that network. The default policy determines whether devices that you add to the
MAC ACL are allowed or denied access to that specific network.
You can set up an independent MAC ACL for each of the four WiFi networks and for
the wired network. That is, the router supports a total of five MAC ACLs.
To enable a MAC ACL for a specific network:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the router admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Security > MAC ACL.
The MAC ACL page displays.
5. Go to the section for the network for which you want to set up a MAC ACL.
The first section is for the admin WiFi network, the second for the employee WiFi
network, the third for the IoT WiFi network, the fourth for the guest WiFi network,
and the fifth for the wired network.
6. For the specific network, click the Enable MAC Access Control Disabled button.
The button changes to the green Enabled button.
Note: If you enabled the network access control list (see Enable the network access
control list and specify the access rule on page 54), you cannot enable any MAC
ACLs. The network access control list and MAC ACLs are mutually exclusive. Use
either the network access control list or MAC ACLs.
7. From the Default Policy menu, select one of the following options:
•Allow. The policy is to allow all devices access except for the devices that you
add to the MAC ACL. Devices on the MAC ACL are denied access to the specific
network.
•Deny. The policy is to deny all devices access except for the devices that you
add to the MAC ACL. Devices on the MAC ACL are allowed access to the specific
network.
User Manual49Control Access to the Internet
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
You can now add and manage devices on the MAC ACL. For more information, see the
following sections:
•Add automatically detected devices to a MAC ACL on page 50
•Manually add, remove, or change the information for a device on a MAC ACL on
page 51
Add automatically detected devices to a MAC ACL
After you set up a MAC ACL for a network and specify the default policy for the MAC
ACL, the router automatically detects devices that are connected or were connected to
the network for which you set up the MAC ACL.
You can select one or multiple devices from the detected list and add them to the MAC
ACL.
To add automatically detected devices to a MAC ACL:
1. Launch a web browser from a computer or mobile device that is connected to the
access point/router network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the router admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Security > MAC ACL.
The MAC ACL page displays.
5. Go to the section for the network for which you want to manage the MAC ACL.
The first section is for the admin WiFi network, the second for the employee WiFi
network, the third for the IoT WiFi network, the fourth for the guest WiFi network,
and the fifth for the wired network.
6. Click the ADD DEVICE button.
The Manual Access Management pop-up window opens.
7. Select the check boxes for the devices that you want to add to the MAC ACL.
8. Click the ADD button.
User Manual50Control Access to the Internet
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
The devices are added to the MAC ACL on the MAC ACL page. Devices on the MAC
ACL are an exception to the default policy:
•If the default policy of the MAC ACL is to allow access, the added devices are
denied access.
•If the default policy of the MAC ACL is to deny access, the added devices are
allowed access.
Manually add, remove, or change the information for a
device on a MAC ACL
After you set up a MAC ACL for a network and specify the default policy for the MAC
ACL, you can manually add a device, remove a device, or change the name (but not
the MAC address) for a device on the MAC ACL.
By manually adding a device, you can proactively control access for a device that is not
or not yet detected, or that was not detected by the router.
To manually add, remove, or change the name for a device on a MAC ACL:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi Pro network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the router admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Security > MAC ACL.
The MAC ACL page displays.
5. Go to the section for the network for which you want to manage the MAC ACL.
The first section is for the admin WiFi network, the second for the employee WiFi
network, the third for the IoT WiFi network, the fourth for the guest WiFi network,
and the fifth for the wired network.
6. To manually add a device to the MAC ACL, do the following:
a. Click the ADD button.
The Manual Access Management pop-up window opens.
b. Enter the MAC address and device name for the device that you want to add.
User Manual51Control Access to the Internet
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
c. In the Manual Access Management pop-up window, click the ADD button.
The device is added to the MAC ACL on the MAC ACL page. Devices on the
MAC ACL are an exception to the default policy:
•If the default policy of the MAC ACL is to allow access, the added device is
denied access.
•If the default policy of the MAC ACL is to deny access, the added device is
allowed access.
7. To remove a device from the MAC ACL, do the following:
a. Select the check box for the device.
b. Click the REMOVE DEVICE button.
The device is removed from the MAC ACL.
8. To change the name for a device on the MAC ACL, do the following:
a. Next to the device in the table., click the EDIT button.
The Manual Access Management pop-up window opens.
b. Change the device name.
c. In the Manual Access Management pop-up window, click the EDIT button.
The device name is changed in the MAC ACL on the MAC ACL page.
Disable a MAC ACL for a specific network
You can disable a MAC ACL that you already set up. The devices are not removed from
the MAC ACL, but all devices on the MAC ACL can connect to the network for which
you setup the MAC ACL, even if the default policy of the MAC ACL is to deny access to
the devices.
To disable a MAC ACL for a specific network:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the router admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
User Manual52Control Access to the Internet
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
4. Select ADVANCED > Security > MAC ACL.
The MAC ACL page displays.
5. Go to the section for the network for which you want to disable the MAC ACL.
The first section is for the admin WiFi network, the second for the employee WiFi
network, the third for the IoT WiFi network, the fourth for the guest WiFi network,
and the fifth for the wired network.
6. For the specific network, click the Enable MAC Access Control Enabled button.
The button changes to the gray Disabled button. The MAC ACL is disabled.
Manage the Orbi network access control list
You can use the network access control list (ACL) to block or allow access to the entire
Orbi network. An ACL functions with the MAC addresses of WiFi and wired devices that
the router detects on the Orbi network and that you can either allow access to your
network or deny access to your network. That is, the router can detect the MAC addresses
of devices that are or were connected to the Orbi network and list the MAC addresses
of these devices.
Note: The network access control list differs from a MAC ACL (see Manage MAC access
control lists for WiFi networks and the LAN on page 48). A MAC ACL is specific to a
particular WiFi network or to the wired network but is not based on devices that the
router detects on the entire Orbi network. With a MAC ACL, you can allow or deny
access to a device on a specific WiFi network or the wired network. The network access
control list and MAC ACLs are mutually exclusive. Use either the network access control
list or MAC ACLs.
If you set up a network ACL with an access rule that allows access to the Orbi network,
devices on the network ACL are an exception to the access rule:
•A device for which you place the MAC address on the network ACL is denied access
to the Orbi network.
•All other devices are allowed access to the Orbi network.
If you set up a network ACL with an access rule that denies access to the Orbi network,
devices on the network ACL are an exception to the access rule:
•A device for which you place the MAC address on the network ACL is allowed access
to the Orbi network.
•All other devices are denied access to the Orbi network.
User Manual53Control Access to the Internet
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Note: Each network device owns a MAC address, which is a unique 12-character physical
address, containing the hexadecimal characters 0–9, a–f, or A–F (uppercase or lowercase)
only, and separated by colons (for example, 00:09:AB:CD:EF:01). Typically, the MAC
address is on the label of a device. If you cannot see the label, you can display the MAC
address using the network configuration utilities of a computer. You might also find the
MAC addresses on Attached Devices page of the router (see View satellites, WiFi devices,
and wired devices connected to the Orbi network on page 117).
Enable the network access control list and specify the access
rule
When you enable network access control, you must select whether new devices are
allowed to access the Orbi network or are blocked from accessing the network. By
default, connected devices are allowed access to the Orbi network, but you can also
block these devices from accessing the Orbi network.
To enable and manage the network access control list for the entire Orbi network:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Security > Access Control.
The Access Control page displays.
5. Select the Turn on Access Control check box.
You must select this check box before you can specify an access rule and use the
ALLOW and BLOCK buttons. When the Turn on Access Control check box is cleared,
all devices are allowed to connect, even if a device is in the list of blocked devices.
Note: If you enabled one or more MAC ACLs (see Enable a MAC ACL for a specific
network on page 49), you cannot use the ALLOW and BLOCK buttons. MAC ACLs
and the network access control list are mutually exclusive. Use either MAC ACLs or
the network access control list.
6. Click the Apply button.
Your settings are saved.
User Manual54Control Access to the Internet
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
7. Select an access rule for new devices:
•Allow all new devices to connect. With this setting, if you add a new device, it
can access the Orbi network. You do not need to enter its MAC address on this
page. We recommend that you leave this radio button selected.
•Block all new devices from connecting. With this setting, if you add a new device,
before it can access the Orbi network, you must enter its MAC address for an
Ethernet connection and its MAC address for a WiFi connection in the allowed
list. For more information, see .
The access rule does not affect previously blocked or allowed devices. It applies
only to devices joining the Orbi network in the future after you apply these settings.
8. To manage access for devices that are connected or were connected to the Orbi
network, do the following:
•If you blocked all new devices from connecting, to allow the device that you are
currently using to continue to access the Orbi network, select the check box next
to your computer or device in the table, and click the ALLOW button.
•To either continue to allow or to block other computers and devices that are
connected or were connected, select the check box next to the device in the table,
and click either the ALLOW button or the BLOCK button.
9. Click the Apply button.
Your settings are saved.
Manage the allowed devices on the network access control
list
If you set up an access list that blocks all new devices from accessing the Orbi network,
you must specify which devices are allowed to access the Orbi network.
You can add a device, remove a device, or edit the information for a device.
To manage devices that are allowed to access to Orbi network:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
User Manual55Control Access to the Internet
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
4. Select ADVANCED > Security > Access Control.
The Access Control page displays.
5. Click the View list of allowed devices not currently connected to the network
link.
A table displays the detected device name, MAC address, and connection type of
the devices that are not connected but allowed to access the Orbi network.
6. To add a device to the allowed list, do the following:
a. Click the ADD button.
The Add Allowed Device page displays.
b. Enter the MAC address and device name for the device that you want to allow.
c. On the Add Allowed Device page, click the Apply button.
The device is added to the allowed list on the Access Control page.
7. To remove a device from the allowed list, do the following:
a. Select the check box for the device.
b. Click the REMOVE FROM THE LIST button.
The device is removed from the allowed list.
8. To change the information for a device on the allowed list, do the following:
a. Select the check box for the device.
b. Click the EDIT button.
The Edit Allowed Device page displays.
c. Change the access rule, MAC address, or device name.
d. On the Edit Allowed Device page, click the Apply button.
The device is changed on the allowed list on the Access Control page.
9. Click the Apply button.
Your settings are saved.
User Manual56Control Access to the Internet
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Manage the blocked devices on the network access control
list
If you set up an access list that allows all new devices to access the Orbi network but
you want to block some devices from accessing the Orbi network, you must specify the
devices that you want to block.
You can add a device, remove a device, or change the information for a device.
To manage devices that are blocked from accessing the Orbi network:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Security > Access Control.
The Access Control page displays.
5. Click the View list of blocked devices not currently connected to the network
link.
The Access Control page displays.
A table displays the detected device name, MAC address, and connection type of
the devices that are not connected and are blocked from accessing the Orbi network.
6. To add a device to the blocked list, do the following:
a. Click the ADD button.
The Add Blocked Device page displays.
b. Enter the MAC address and device name for the device that you want to block.
c. On the Add Blocked Device page, click the Apply button.
The device is added to the blocked list on the Access Control page.
7. To remove a device from the blocked list, do the following:
a. Select the check box for the device.
b. Click the REMOVE FROM THE LIST button.
The device is removed from the blocked list.
User Manual57Control Access to the Internet
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
8. To change the information for a device on the blocked list, do the following:
a. Select the check box for the device.
b. Click the EDIT button.
The Edit Blocked Device page displays.
c. Change the access rule, MAC address, or device name.
d. On the Edit Blocked Device page, click the Apply button.
The device is changed on the blocked list on the Access Control page.
9. Click the Apply button.
Your settings are saved.
Use keywords to block Internet sites
You can use keywords to block certain Internet sites from your network. You can use
blocking all the time or based on a schedule.
To block Internet sites:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Security > Block Sites.
The Block Sites page displays.
5. Select a keyword blocking option:
•Per Schedule. Turn on keyword blocking according to a schedule that you set.
(See Schedule When to Block Internet Sites and Services on page 56.)
•Always. Turn on keyword blocking all the time, independent of the Schedule
page.
User Manual58Control Access to the Internet
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
6. In the Type keyword or domain name here field, enter a keyword or domain that
you want to block.
For example:
•Specify XXX to block http://www.badstuff.com/xxx.html.
•Specify .com if you want to allow only sites with domain suffixes such as .edu or
.gov.
•Enter a period (.) to block all Internet browsing access.
7. Click the Add Keyword button.
The keyword is added to the keyword list. The keyword list supports up to 32 entries.
8. Click the Apply button.
Keyword blocking takes effect.
Delete keywords that are used to block
Internet sites
To delete keywords that are used to block Internet sites:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Security > Block Sites.
The Block Sites page displays.
5. Do one of the following:
•To delete a single word, select it and click the Delete Keyword button.
The keyword is removed from the list.
•To delete all keywords on the list, click the Clear List button.
All keywords are removed from the list.
User Manual59Control Access to the Internet
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
6. Click the Apply button.
Your settings are saved.
Avoid blocking on a trusted computer
You can exempt one trusted computer from blocking. The computer that you exempt
must be assigned a fixed IP address. You can use the reserved IP address feature to
specify the IP address. See Manage reserved LAN IP addresses on page 75.
To specify a trusted computer:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Security > Block Sites.
The Block Sites page displays.
5. Scroll down and select the Allow trusted IP address to visit blocked sites check
box.
6. In the Trusted IP Address field, enter the IP address of the trusted computer.
7. Click the Apply button.
Your settings are saved.
Block services from the Internet
You can block Internet services on your network based on the type of service. You can
block the services all the time or based on a schedule.
To block services:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
User Manual60Control Access to the Internet
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Security > Block Services.
The Block Services page displays.
5. Specify when to block the services:
•To block the services all the time, select the Always radio button.
•To block the services based on a schedule, select the Per Schedule radio button.
For information about how to specify the schedule, see Schedule when to block
Internet sites and services on page 62.
6. Click the Add button.
The Block Services Setup page displays.
7. To add a service that is in the Service Type list, select the application or service.
The settings for this service automatically display in the fields.
8. To add a service or application that is not the list, select User Defined.
a. If you know that the application uses either TCP or UDP, select the appropriate
protocol.
Otherwise, select TCP/UDP (both).
b. Enter the starting port and ending port numbers.
•If the service uses a single port number, enter that number in both fields.
•To find out which port numbers the service or application uses, you can contact
the publisher of the application, ask user groups or newsgroups, or search
on the Internet.
9. To specify how to filter the services, select one of the following radio buttons:
•Only This IP Address. Block services for a single computer.
•IP Address Range. Block services for a range of computers with consecutive IP
addresses on your network.
•All lP Addresses. Block services for all computers on your network.
User Manual61Control Access to the Internet
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
10. Click the Add button.
Your settings are saved.
Schedule when to block Internet sites and
services
When you schedule blocking, the same schedule is used to block sites and to block
services. For information about how to specify what you want the router to block, see
Use keywords to block Internet sites on page 58 and Avoid blocking on a trusted
computer on page 60.
To schedule blocking:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Security > Schedule.
5. Specify when to block keywords and services:
•Days to Block. Select the check box for each day that you want to block the
keywords or select the Every Day check box, which automatically selects the
check boxes for all days.
•Time of Day to Block. Select a start and end time in 24-hour format, or select
All Day for 24-hour blocking.
6. Select your time zone from the list.
7. If you live in a region that observes daylight saving time, select the Automatically
adjust for daylight savings time check box.
8. Click the Apply button.
Your settings are saved.
User Manual62Control Access to the Internet
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Set up security event email notifications
The router can email you its logs of router activity. The log records router activity and
security events such as attempts to access blocked sites or services.
To set up email notifications:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Security > E-mail.
The E-mail page displays.
5. Select the Turn Email Notification On check box.
6. In the Primary E-mail Address field, enter the email address to which logs and alerts
are sent.
This email address is also used for the From address. If this field is blank, log and
alert messages are not sent.
7. In the Your Outgoing Mail Server field, enter the name of your ISP outgoing (SMTP)
mail server (such as mail.myISP.com).
You might be able to find this information in the configuration window of your email
program. If you leave this field blank, log and alert messages are not sent.
8. In the Outgoing Mail Server Port Number field, enter your mail server’s port
number.
You might be able to find this information in the configuration window of your email
program.
9. If your outgoing email server requires authentication, select the My Mail Server
requires authentication check box and do the following:
•In the User Name field, type the user name for the outgoing email server.
•In the Password field, type the password for the outgoing email server.
10. To send alerts immediately, select the Send Alerts Immediately check box.
User Manual63Control Access to the Internet
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Email alerts are sent immediately when someone attempts to visit a blocked site.
11. To send logs based on a schedule, specify these settings:
•From Send logs according to this schedule menu, select the schedule type.
•From the Day menu, select the day.
•From the Time menu, select the time, and select the am or pm radio button.
12. Click the Apply button.
Your settings are saved.
Logs are sent automatically. If the log fills before the specified time, it is sent. After
the log is sent, it is cleared from the router memory. If the router cannot email the
log and the log buffer fills, the router overwrites the log.
User Manual64Control Access to the Internet
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
5
Specify Network Settings
This chapter includes the following sections:
• View or change WAN settings
• Manage Dynamic DNS
• Set up a default DMZ server
• Change the router’s device name
• Change the LAN TCP/IP settings
• Use the router as a DHCP server
• Disable the DHCP server feature in the router
• Manage reserved LAN IP addresses
• Manage custom static routes
• Change the admin WiFi network settings
• Manage the employee WiFi network settings
• Manage the IoT WiFi network settings
• Set up a guest WiFi network and captive portal
• Manage the download bandwidth per SSID
• View or change advanced WiFi settings
• Use the router as a WiFi access point
• Set up router mode
• Generate a new backhaul password
• Enable or disable implicit beamforming
• Enable or disable MU-MIMO
• Enable or disable Protected Management Frames
• Check your Internet bandwidth
• Set up a bridge for a port group or VLAN tag group
• Improve network connections with Universal Plug and Play
65
View or change WAN settings
You can view or configure wide area network (WAN) settings for the Internet port. You
can set up a DMZ (demilitarized zone) server, change the maximum transmit unit (MTU)
size, and enable the router to respond to a ping to its WAN (Internet) port.
To view the WAN settings:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Setup > WAN Setup
The WAN Setup page displays.
5. View or change the following settings:
•Disable Port Scan and DoS Protection. DoS protection protects your LAN against
denial of service attacks such as Syn flood, Smurf Attack, Ping of Death, and many
others. Select this check box only in special circumstances.
•Default DMZ Server. This feature is sometimes helpful when you are playing
online games or videoconferencing, but it makes the firewall security less effective.
See Set up a default DMZ server on page 69.
•Respond to Ping on Internet Port. This feature allows your router to be
discovered. Use this feature only as a diagnostic tool or if you have a specific
reason.
•Disable IGMP Proxying. IGMP proxying allows a computer on the local area
network (LAN) to receive the multicast traffic it is interested in from the Internet.
If you do not need this feature, select this check box to disable it.
•MTU Size (in bytes). The normal MTU (maximum transmit unit) value for most
Ethernet networks is 1500 bytes, or 1492 bytes for PPPoE connections. Change
the MTU only if you are sure that it is necessary for your ISP connection. See
Change the MTU size on page 45.
•NAT Filtering. Network Address Translation (NAT) determines how the router
processes inbound traffic. Secured NAT protects computers on the LAN from
attacks from the Internet, but might prevent some Internet games, point-to-point
User Manual66Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
applications, or multimedia applications from working. Open NAT provides a
much less secured firewall, but allows almost all Internet applications to work.
6. Click the Apply button.
Your settings are saved.
Manage Dynamic DNS
Internet service providers (ISPs) assign numbers called IP addresses to identify each
Internet account. Most ISPs use dynamically assigned IP addresses. This means that the
IP address can change at any time. You can use the IP address to access your network
remotely, but most people don’t know what their IP addresses are or when this number
changes.
To make it easier to connect, you can get a free account with a Dynamic DNS service
that lets you use a domain name to access your home network. To use this account, you
must set up the router to use Dynamic DNS. Then the router notifies the Dynamic DNS
service provider whenever its IP address changes. When you access your Dynamic DNS
account, the service finds the current IP address of your home network and automatically
connects you.
If your ISP assigns a private WAN IP address (such as 192.168.x.x or 10.x.x.x), the Dynamic
DNS service does not work because private addresses are not routed on the Internet.
Set up a new Dynamic DNS account
To set up Dynamic DNS and register for a free NETGEAR account:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Dynamic DNS.
The Dynamic DNS page displays.
5. Select the Use a Dynamic DNS Service check box.
User Manual67Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
6. In the Service Provider list, select NETGEAR.
7. Select the No radio button.
8. In the Host Name field, type the name that you want to use for your URL.
The host name is sometimes called the domain name. Your free URL includes the
host name that you specify, and ends with mynetgear.com. For example, specify
MyName.mynetgear.com.
9. In the Email field, type the email address that you want to use for your account.
10. In the Password (6-32 characters) field, type the password for your account.
11. Click the Register button.
12. Follow the onscreen instructions to register for your NETGEAR Dynamic DNS service.
13. To check that Dynamic DNS is enabled in the router, click the Show Status button.
A message displays the Dynamic DNS status.
Specify a DNS account that you already created
If you already own a Dynamic DNS account with NETGEAR, no-IP, or Dyn, you can set
up the router to use your account.
To set up Dynamic DNS if you already created an account:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Dynamic DNS.
The Dynamic DNS page displays.
5. Select the Use a Dynamic DNS Service check box.
6. In the Service Provider list, select your provider.
7. Select the Yes radio button.
The page adjusts and displays to show the Status,Cancel, and Apply buttons.
User Manual68Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
8. In the Host Name field, type the host name (sometimes called the domain name)
for your account.
9. For a no-IP Dyn account, in the User Name field, enter the user name for your account.
10. For a NETGEAR account at no-IP, in the Email field, type the email address for your
account.
11. In the Password (6-32 characters) field, type the password for your DDNS account.
12. Click the Apply button.
Your settings are saved.
13. To verify that your Dynamic DNS service is enabled in the router, click the Show
Status button.
A message displays the Dynamic DNS status.
Change the Dynamic DNS settings
To change your settings:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Dynamic DNS.
The Dynamic DNS page displays.
5. Change your DDNS account settings as necessary.
6. Click the Apply button.
Your settings are saved.
Set up a default DMZ server
The default DMZ server feature is helpful when you are using some online games and
videoconferencing applications that are incompatible with Network Address Translation
(NAT). The router is programmed to recognize some of these applications and to work
User Manual69Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
correctly with them, but other applications might not function well. In some cases, one
local computer can run the application correctly if the IP address for that computer is
entered as the default DMZ server.
DMZ servers pose a security risk. A computer designated as the default DMZ server
loses much of the protection of the firewall and is exposed to exploits from the Internet.
If compromised, the DMZ server computer can be used to attack other computers on
your network.
The router usually detects and discards incoming traffic from the Internet that is not a
response to one of your local computers or a service that you configured in the Port
Forwarding/Port Triggering page. Instead of discarding this traffic, you can specify that
the router forwards the traffic to one computer on your network. This computer is called
the default DMZ server.
To set up a default DMZ server:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Setup > WAN Setup.
The WAN Setup page displays.
5. Select the Default DMZ Server check box.
6. Type the IP address.
7. Click the Apply button.
Your settings are saved.
Change the router’s device name
The router’s device name is its model number. This device name displays in a file
manager when you browse your network.
User Manual70Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
To change the router’s device name:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Setup > Device Name.
The Device Name page displays.
5. In the Device Name field, type a new name.
6. Click the Apply button.
Your settings are saved.
Change the LAN TCP/IP settings
The router is preconfigured to use private IP addresses on the LAN side and to act as
a DHCP server. The router’s default LAN IP configuration is as follows:
•LAN IP address. 192.168.1.1
•Subnet mask. 255.255.255.0
These addresses are part of the designated private address range for use in private
networks and are suitable for most applications. If your network requires a different IP
addressing scheme, you can change these settings.
You might want to change these settings if you need a specific IP subnet that one or
more devices on the network uses, or if you use competing subnets with the same IP
scheme.
To change the LAN TCP/IP settings:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
User Manual71Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Setup > LAN Setup.
The LAN Setup page displays.
5. In the IP Address field, type the IP address.
6. In the IP Subnet Mask, type the subnet mask of the router.
The IP address and subnet mask identifies which addresses are local to a specific
device and which must be reached through a gateway or router.
7. Change the RIP settings.
Router Information Protocol (RIP) allows a router to exchange routing information
with other routers.
a. Select the RIP direction:
•Both. The router broadcasts its routing table periodically and incorporates
information that it receives.
•Out Only. The router broadcasts its routing table periodically.
•In Only. The router incorporates the RIP information that it receives.
b. Select the RIP version:
•Disabled. This is the default setting.
•RIP-1. This format is universally supported. It is adequate for most networks,
unless you are using an unusual network setup.
•RIP-2. This format carries more information. Both RIP-2B and RIP-2M send the
routing data in RIP-2 format. RIP-2B uses subnet broadcasting. RIP-2M uses
multicasting.
8. Click the Apply button.
Your settings are saved.
If you changed the LAN IP address of the router, you are disconnected when this
change takes effect.
9. To reconnect, close your browser, relaunch it, and log in to the router.
User Manual72Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Use the router as a DHCP server
By default, the router acts as a Dynamic Host Configuration Protocol (DHCP) server. The
router assigns IP, DNS server, and default gateway addresses to all computers connected
to the LAN. The assigned default gateway address is the LAN address of the router.
These addresses must be part of the same IP address subnet as the router’s LAN IP
address. Using the default addressing scheme, define a range between 192.168.1.2
and 192.168.1.254, although you can save part of the range for devices with fixed
addresses.
To use the router as a DHCP server and specify the pool of IP addresses that the
router assigns:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Setup > LAN Setup.
The LAN Setup page displays.
5. If you previously disabled the DHCP server feature, select the Use Router as DHCP
Server check box.
6. Specify the range of IP addresses that the router assigns:
a. In the Starting IP Address field, enter the lowest number in the range.
This IP address must be in the same subnet as the router. The default starting IP
address is 192.168.1.2.
b. In the Ending IP Address field, enter the number at the end of the range of IP
addresses.
This IP address must be in the same subnet as the router. The default ending IP
address is 192.168.1.254.
7. Click the Apply button.
Your settings are saved.
User Manual73Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
The router delivers the following parameters to any LAN device that requests DHCP:
•An IP address from the range that you defined
•Subnet mask
•Gateway IP address (the router’s LAN IP address)
•DNS server IP address (the router’s LAN IP address)
Disable the DHCP server feature in the router
By default, the router acts as a DHCP server. The router assigns IP, DNS server, and
default gateway addresses to all computers connected to the LAN. The assigned default
gateway address is the LAN address of the router.
You can use another device on your network as the DHCP server, or specify the network
settings of all your computers.
To disable the DHCP server feature in the router:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Setup > LAN Setup.
The LAN Setup page displays.
5. Clear the Use Router as DHCP Server check box.
6. Click the Apply button.
7. (Optional) If this service is disabled and no other DHCP server is on your network,
set your computer IP addresses manually so that they can access the router.
User Manual74Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Manage reserved LAN IP addresses
When you specify a reserved IP address for a computer on the LAN, that computer
always receives the same IP address each time it accesses the router’s DHCP server.
Assign reserved IP addresses to computers or servers that require permanent IP settings.
Reserve an IP address
To reserve an IP address:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Setup > LAN Setup.
The LAN Setup page displays.
5. In the Address Reservation section of the page, click the Add button.
6. In the IP Address field, type the IP address to assign to the computer or server.
The page adjusts.
7. Choose an IP address from the router’s LAN subnet, such as 192.168.1.x.
8. Type the MAC address of the computer or server.
Tip: If the computer is already on your network, you can copy its MAC address from
the Attached Devices page and paste it here.
9. Click the Apply button.
The reserved address is entered into the table.
The reserved address is not assigned until the next time the computer contacts the
router’s DHCP server. Reboot the computer, or access its IP configuration and force
a DHCP release and renew.
User Manual75Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Edit a reserved IP address
To edit a reserved address entry:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Setup > LAN Setup.
The LAN Setup page displays.
5. Select the radio button next to the reserved address.
6. Click the Edit button.
The Address Reservation page displays.
7. Change the settings.
8. Click the Apply button.
Your settings are saved.
Delete a reserved IP address entry
To delete a reserved address entry:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Setup > LAN Setup.
The LAN Setup page displays.
User Manual76Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
5. Select the radio button next to the reserved address.
6. Click the Delete button.
The address is removed.
Manage custom static routes
Typically, you do not need to add static routes unless you use multiple routers or multiple
IP subnets on your network.
As an example of when a static route is needed, consider the following case:
•Your main Internet access is through a cable modem to an ISP.
•Your home network includes an ISDN router for connecting to the company where
you are employed. This router’s address on your LAN is 192.168.1.100.
•Your company’s network address is 134.177.0.0.
When you set up your router, two implicit static routes were created. A default route
was created with your ISP as the gateway, and a second static route was created to your
local network for all 192.168.1.x addresses. With this configuration, if you try to access
a device on the 134.177.0.0 network, your router forwards your request to the ISP. The
ISP forwards your request to the company where you are employed, and the company
firewall is likely to deny the request.
In this case you must define a static route, telling your router to access 134.177.0.0
through the ISDN router at 192.168.1.100. Here is an example:
•The Destination IP Address and IP Subnet Mask fields specify that this static route
applies to all 134.177.x.x addresses.
•The Gateway IP Address field specifies that all traffic for these addresses will be
forwarded to the ISDN router at 192.168.1.100.
•A metric value of 1 works because the ISDN router is on the LAN.
•The Private check box is selected only as a precautionary security measure in case
RIP is activated.
Set up a static route
To set up a static route:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
User Manual77Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Static Routes.
The Static Routes page displays.
5. Click the Add button.
The page adjusts.
6. In the Route Name field, type a name for this static route (for identification purposes
only.)
7. To limit access to the LAN only, select the Private check box.
If Private is selected, the static route is not reported in RIP.
8. Select the Active check box to make this route take effect.
9. Type the IP address of the final destination.
10. Type the IP subnet mask for this destination.
If the destination is a single host, type 255.255.255.255.
11. Type the gateway IP address.
This address must be on the same LAN segment as the router.
12. Type a number from 1 through 15 as the metric value.
This value represents the number of routers between your network and the
destination. Usually, a setting of 2 or 3 works, but if this is a direct connection, set it
to 1.
13. Click the Apply button.
The static route is added.
Edit a static route
To edit a static route:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
User Manual78Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Static Routes.
The Static Routes page displays.
5. In the table, select the radio button for the route.
6. Click the Edit button.
The Static Routes page adjusts.
7. Edit the route information.
8. Click the Apply button.
Your settings are saved.
Delete a static route
To delete a static route:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Static Routes.
The Static Routes page displays.
5. In the table, select the radio button for the route.
6. Click the Delete button.
The route is removed from the table.
User Manual79Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Change the admin WiFi network settings
You can set up four WiFi networks for your Orbi Pro network: one for administrative
access, one for employee access, one for Internet of things (IoT) devices, and one for
guest access.
Your Orbi Pro router and satellite come preset with the same admin WiFi network name
(SSID) and WiFi network key (password). You can find the admin SSID and password
on the router label and on the satellite label. The preset WiFi settings on the labels are
for your admin WiFi network. When you log in to the router and change the WiFi settings,
the router automatically sends the new settings to the satellite.
Note: The router web interface calls the admin WiFi network the Wireless 1 network.
Change the admin WiFi network name and channel
If you change your WiFi settings, make a note of the new settings and store it in a safe
place where you can easily find it.
If your computer or mobile device is using a WiFi connection when you change the
network name (SSID) or other WiFi security settings, you are disconnected when you
click the Apply button. To avoid this problem, use a computer with a wired connection
to access the router.
Note: The router web interface calls the admin WiFi network the Wireless 1 network.
To change the admin WiFi settings:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Wireless.
The Wireless Settings page displays the admin WiFi settings.
5. To change the admin network name (SSID), type a new name in the Name (SSID)
field.
User Manual80Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
The name can be up to 32 characters long and it is case-sensitive. The default SSID
is randomly generated and is on the router label. If you change the name, make sure
to write down the new name and keep it in a safe place.
6. To change the 2.4 GHz or 5 GHz WiFi channel, select a number from the Channel
menus.
In some regions, not all channels are available. Do not change the channel unless
you experience interference (shown by lost connections or slow data transfers). If
this happens, experiment with different channels to see which channel works bets
for your.
When you use multiple routers, satellites, or extenders in your network (access
points), you experience less interference if adjacent access points use different. The
recommended channel spacing NETGEAR recommends a minimum of four channels
between adjacent access points (for example, use channels 1 and 5, or 6 and 10).
7. Click the Apply button.
Your settings are saved. The router sends the new settings to the satellite.
If you are using a WiFi connection and you changed the SSID, you are disconnected
from the network.
8. Make sure that you can connect to the WiFi network with its new settings.
If you cannot connect using WiFi, check the following:
•Is your WiFi-enabled computer or mobile device connected to another WiFi
network in your area? Some WiFi devices automatically connect to the first open
network without WiFi security that they discover.
•Is your computer or WiFi device trying to connect to your network with its old
settings (before you changed the settings)? If so, update the WiFi network
selection in your computer or WiFi device to match the current settings for your
network.
Change the admin WiFi password or security level
We recommend that you do not disable security for your WiFi network.
Note: The router web interface calls the admin WiFi network the Wireless 1 network.
To change the admin WiFi password or WPA settings:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
User Manual81Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Wireless.
The Wireless Settings page displays the admin WiFi settings.
5. Under Security Options, select a WPA option:
•WPA2-PSK [AES]. The WPA2 option uses the newest standard for the strongest
security, but some older computers and WiFi devices cannot use WPA2.
When you select this option, the Password (Network Key) field displays. Do the
following:
a. In the Password (Network Key) field, enter the network key (password) that
you want to use.
It is a text string from 8 to 63 characters.
b. Write down the new password and keep it in a secure place for future
reference.
•WPA-PSK [TKIP] + WPA2-PSK [AES]. If your network includes old computers
and WiFi devices, select this radio button.
When you select this option, the Password (Network Key) field displays. Do the
following:
a. In the Password (Network Key) field, enter the network key (password) that
you want to use.
It is a text string from 8 to 63 characters.
b. Write down the new password and keep it in a secure place for future
reference.
•WPA2 Enterprise. If your network is connected to a RADIUS server that can
provide authentication, select this radio button. WPA2 Enterprise can provide
the highest level of security. Before a WiFi client can connect to the Wireless 1
network, the WiFi client must be configured on the RADIUS server and
authenticated against the RADIUS server. The router functions as the authenticator
between the WiFi client and the RADIUS server, which provides the actual
authentication.
User Manual82Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
When you select this option, additional fields display so that you can specify the
RADIUS server. Do the following:
a. In the IP address field, enter the IP address of the RADIUS server to which
the router must connect.
b. In the Port field, enter the port number that the router must use to
communicate with the RADIUS server.
By default, the port number is 1812.
c. In the Shared Secret field, enter the password that the router must use to
communicate with the RADIUS server.
This password must be configured on the RADIUS server. This password is
used to authenticate the router (not a WiFi client) against the RADIUS server.
6. Click the Apply button.
Your settings are saved.
Manage the employee WiFi network settings
You can set up four WiFi networks for your Orbi Pro network: one for administrative
access, one for employee access, one for Internet of things (IoT) devices, and one for
guest access.
When employee devices connect to the employee WiFi network, they cannot see other
devices that are connected to the network and cannot access the local area network
(LAN).
Note: The router web interface calls the employee WiFi network the Wireless 2 network.
Enable the employee WiFi network and change the settings
Before you can set up the employee WiFi network, you must enable it. You must be
connected to the admin network to enable the employee WiFi network and change the
settings.
When employee devices connect to the employee WiFi network, they cannot see other
devices that are connected to the network and cannot access the local area network
(LAN).
Note: The router web interface calls the employee WiFi network the Wireless 2 network.
User Manual83Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
To enable the employee WiFi network and change the WiFi settings:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Wireless > Wireless 2.
The WiFi settings for the Wireless 2 network display on the page.
5. To enable the Wireless 2 network, select the Enable Wireless 2 network check box.
By default, the Wireless 2 network is disabled.
6. To broadcast the Wireless 2 network SSID, select the Enable SSID Broadcast check
box.
By default, the broadcast is enabled.
7. To allow your employees to see each other on the Wireless 2 network, and to allow
them to access resources on the local network, select the Allow employees to see
each other and access my local network check box.
By default, employees are not allowed to see each other and cannot access local
resources on the Wireless 2 network.
8. To change the Wireless 2 network name (SSID), type a new name in the Wireless 2
Network Name (SSID) field.
The name can be up to 32 characters long and it is case-sensitive. The default SSID
is randomly generated and is on the router’s label. If you change the name, make
sure to write down the new name and keep it in a safe place.
9. To separate the single SSID for the Wireless 2 network in an SSID for the 2.4 GHz
band and another SSID for the 5 GHz band, select the Enable SSID separation for
2.4G/5GHz check box.
For each band, a Wireless 2 Network Name (SSID) field displays. The SSID for the 5
GHz band is prepended with _5G, but you can also type another name.
By default, the Wireless 2 network provides a single SSID for both bands.
10. Click the Apply button.
Your settings are saved. The router sends the new settings to the satellite.
User Manual84Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
11. Make sure that a user can connect to the WiFi network with its new settings.
If you cannot connect using WiFi, check the following:
•Is your WiFi-enabled computer or mobile device connected to another WiFi
network in your area? Some WiFi devices automatically connect to the first open
network without WiFi security that they discover.
•Is your computer or mobile device trying to connect to your network with its old
settings (before you changed the settings)? If so, update the WiFi network
selection in your computer or WiFi device to match the current settings for your
network.
Change the employee WiFi password or security level
You must be connected to the admin network to change the employee password and
security level.
Note: The router web interface calls the employee WiFi network the Wireless 2 network.
To change the employee WiFi network password or WPA settings:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Wireless > Wireless 2.
The WiFi settings for the wireless 2 network display on the page.
5. Under Security Options, select a WPA option:
•WPA2-PSK [AES]. The WPA2 option uses the newest standard for the strongest
security, but some older computers and WiFi devices cannot use WPA2.
User Manual85Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
When you select this option, the Password (Network Key) field displays. Do the
following:
a. In the Password (Network Key) field, enter the network key (password) that
you want to use.
It is a text string from 8 to 63 characters.
b. Write down the new password and keep it in a secure place for future
reference.
•WPA-PSK [TKIP] + WPA2-PSK [AES]. If your network includes old computers
and WiFi devices, select this radio button.
When you select this option, the Password (Network Key) field displays. Do the
following:
a. In the Password (Network Key) field, enter the network key (password) that
you want to use.
It is a text string from 8 to 63 characters.
b. Write down the new password and keep it in a secure place for future
reference.
•WPA2 Enterprise. If your network is connected to a RADIUS server that can
provide authentication, select this radio button. WPA2 Enterprise can provide
the highest level of security. Before a WiFi client can connect to the Wireless 2
network, the WiFi client must be configured on the RADIUS server and
authenticated against the RADIUS server. The router functions as the authenticator
between the WiFi client and the RADIUS server, which provides the actual
authentication.
When you select this option, additional fields display so that you can specify the
RADIUS server. Do the following:
a. In the IP address field, enter the IP address of the RADIUS server to which
the router must connect.
b. In the Port field, enter the port number that the router must use to
communicate with the RADIUS server.
By default, the port number is 1812.
c. In the Shared Secret field, enter the password that the router must use to
communicate with the RADIUS server.
This password must be configured on the RADIUS server. This password is
used to authenticate the router (not a WiFi client) against the RADIUS server.
6. Click the Apply button.
Your settings are saved.
User Manual86Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Manage the IoT WiFi network settings
You can set up four WiFi networks for your Orbi Pro network: one for administrative
access, one for employee access, one for Internet of things (IoT) devices, and one for
guest access.
When IoT devices connect to the IoT WiFi network, they cannot see other devices that
are connected to the network and cannot access the local area network (LAN).
Note: The router web interface calls the IoT WiFi network the Wireless 3 network.
Enable the IoT WiFi network and change the settings
Before you can set up the IoT WiFi network, you must enable it. You must be connected
to the admin network to enable the IoT WiFi network and change the settings.
When IoT devices connect to the IoT WiFi network, they cannot see other devices that
are connected to the network and cannot access the local area network (LAN).
Note: The router web interface calls the IoT WiFi network the Wireless 3 network.
To enable the IoT WiFi network and change the WiFi settings:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Wireless > Wireless 3.
The WiFi settings for the Wireless 3 network display on the page.
5. To enable the Wireless 3 network, select the Enable Wireless 3 network check box.
By default, the Wireless 3 network is disabled.
6. To broadcast the Wireless 3 network SSID, select the Enable SSID Broadcast check
box.
By default, the broadcast is enabled.
User Manual87Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
7. To allow the IoT devices to see each other on the Wireless 3 network, and to allow
them to access resources on the local network, select the Allow IoT devices to see
each other and access my local network check box.
By default, IoT devices are not allowed to see each other and access local resources
on the Wireless 3 network.
8. To change the Wireless 3 network name (SSID), type a new name in the Wireless 3
Network Name (SSID) field.
The name can be up to 32 characters long and it is case-sensitive. The default SSID
is NETGEAR_IOT. If you change the name, make sure to write down the new name
and keep it in a safe place.
9. To separate the single SSID for the Wireless 3 network in an SSID for the 2.4 GHz
band and another SSID for the 5 GHz band, select the Enable SSID separation for
2.4G/5GHz check box.
For each band, a Wireless 3 Network Name (SSID) field displays. The SSID for the 5
GHz band is prepended with _5G (NETGEAR_IOT_5G), but you can also type another
name.
By default, the Wireless 3 network provides a single SSID for both bands.
10. Click the Apply button.
Your settings are saved. The router sends the new settings to the satellite.
11. Make sure that an IoT device can connect to the WiFi network with its new settings.
If you cannot connect using WiFi, check the following:
•Is your WiFi-enabled computer or mobile device connected to another WiFi
network in your area? Some WiFi devices automatically connect to the first open
network without WiFi security that they discover.
•Is your computer or mobile device trying to connect to your network with its old
settings (before you changed the settings)? If so, update the WiFi network
selection in your computer or WiFi device to match the current settings for your
network.
Change the IoT WiFi password or security level
You must be connected to the admin network to change the IoT password and security
level.
Note: The router web interface calls the IoT WiFi network the Wireless 3 network.
User Manual88Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
To change the IoT WiFi network password or WPA settings:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Wireless > Wireless 3.
The WiFi settings for the wireless 3 network display on the page.
5. Under Security Options, select a WPA option:
•WPA2-PSK [AES]. The WPA2 option uses the newest standard for the strongest
security, but some older computers and WiFi devices cannot use WPA2.
When you select this option, the Password (Network Key) field displays. Do the
following:
a. In the Password (Network Key) field, enter the network key (password) that
you want to use.
It is a text string from 8 to 63 characters.
b. Write down the new password and keep it in a secure place for future
reference.
•WPA-PSK [TKIP] + WPA2-PSK [AES]. If your network includes old computers
and WiFi devices, select this radio button.
When you select this option, the Password (Network Key) field displays. Do the
following:
a. In the Password (Network Key) field, enter the network key (password) that
you want to use.
It is a text string from 8 to 63 characters.
b. Write down the new password and keep it in a secure place for future
reference.
•WPA2 Enterprise. If your network is connected to a RADIUS server that can
provide authentication, select this radio button. WPA2 Enterprise can provide
the highest level of security. Before a WiFi client can connect to the Wireless 3
network, the WiFi client must be configured on the RADIUS server and
authenticated against the RADIUS server. The router functions as the authenticator
User Manual89Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
between the WiFi client and the RADIUS server, which provides the actual
authentication.
When you select this option, additional fields display so that you can specify the
RADIUS server. Do the following:
a. In the IP address field, enter the IP address of the RADIUS server to which
the router must connect.
b. In the Port field, enter the port number that the router must use to
communicate with the RADIUS server.
By default, the port number is 1812.
c. In the Shared Secret field, enter the password that the router must use to
communicate with the RADIUS server.
This password must be configured on the RADIUS server. This password is
used to authenticate the router (not a WiFi client) against the RADIUS server.
6. Click the Apply button.
Your settings are saved.
Set up a guest WiFi network and captive
portal
You can set up a guest WiFi network (guest portal), which allows visitors to access the
Internet using a dedicated SSID. You can also set up a captive portal for the guest portal.
With a captive portal, when visitors connect to the guest portal and open a browser to
access the Internet, they are redirected to a splash page where they must agree to the
Terms of Conditions before they can access Internet.
By default, visitors do not need to enter a password to connect to the guest portal and
data is not encrypted. Open access without security might be a good option for a coffee
shop. For situations in which authentication is required, you can use Facebook Wi-Fi or
set a password.
When using this network, visitors cannot see other devices that are connected to the
guest portal (or any other WiFi network on the router) and they cannot access the local
area network (LAN).
Set up a guest WiFi network with open access or password
authentication
A guest WiFi network is also referred to as a guest portal.
User Manual90Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
To set up a guest network:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the Orbi admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Guest Portal.
The Guest Portal Settings page displays.
5. To enable the guest portal, select the Enable Guest Portal Network check box.
By default, the guest portal is disabled.
6. Leave the Enable SSID Broadcast check box selected.
Allowing the router to broadcast its WiFi network name (SSID) makes it easier to find
your network and connect to it. If you clear this check box, that creates a hidden
network.
7. To change the network name, type a new name in the Guest Portal Network Name
(SSID) field.
The name can be up to 32 characters long and it is case-sensitive. If you change the
name, make sure to write down the new name and keep it in a safe place.
8. In the Authentication Mode section, leave the Local radio button selected.
9. In the Authentication Options section, either specify an open network or set an
authentication password by doing one of the following:
•None. To specify an open network without authentication, select the None radio
button.
•Password Authentication. To set an authentication password, select the
Password Authentication radio button and specify a password in the field. The
password must be a minimum of 8 characters and can be a maximum of 64
characters.
Note: In order for visitors to access the Internet, they must enter this password
in the guest portal.
User Manual91Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
10. To set an expiration time for how long visitors can access the Internet, select a time
from the Expiration menu. After visitors are authenticated, they can access the
Internet for that period of time.
If you select Never from the menu, visitor access time is not restricted to any period.
11. Click the Apply button.
Your settings are saved. The router sends the new settings to the satellite.
Set up a guest network with a captive portal
A captive portal is an entry to a guest network that requires guests to view a splash page
and agree to terms and conditions before using the network. When using captive portal
guest networks visitors cannot see other devices that are connected and they cannot
access the local area network (LAN).
To set up a guest network with a captive portal:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Guest Portal.
The Guest Portal Settings page displays.
5. Select the Enable Guest Portal check box.
6. Leave the Enable SSID Broadcast check box selected.
Allowing the router to broadcast its WiFi network name (SSID) makes it easier to find
your network and connect to it. If you clear this check box, that creates a hidden
network.
7. To change the network name, type a new name in the Guest Portal Network Name
(SSID) field.
The name can be up to 32 characters long and it is case-sensitive. If you change the
name, make sure to write down the new name and keep it in a safe place.
8. In the Authentication Mode section, select the Local radio button.
The page adjusts.
User Manual92Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
9. To set a guest portal password, select the Password Authentication radio button
and enter the password in the field.
The password must be a minimum of 8 characters and can be a maximum of 64
characters.
Note: In order for visitors to access the Internet, they must enter this password in
the guest portal and click the AGREE button to accept terms and conditions.
10. To set an expiration time for how long users can access the Internet, select a time
from the Expiration menu.
After visitors are authenticated, they can access the Internet for that period of time.
After the period expires, visitors are redirected to the Terms and Conditions page.
11. To include a custom Terms and Conditions page, click the Browse button in the
Terms and Conditions section.
12. Locate and select the terms and conditions file on your computer.
The file must be a .txt file, encoded in UTF8 format, and can be up to 1 MB.
13. To include a custom logo file, click the Browse button in the Logo section.
14. Locate and select the logo file on your computer.
The file must be a .jpg, .jpeg, .gif, or .webp file. The file size must be up to 10 MB and
the dimensions must be 200 x 200 pixels.
15. To preview the guest portal, click the Preview button.
To preview the Terms and Conditions page, either the terms and conditions and
logo files must both be set to Default or you must upload new files for both. You
cannot preview the Terms and Conditions page if one file is set to Default.
16. To set up a redirect URL, select the URL radio button and enter the URL for the page
to which you want to redirect users to in the field.
After visitors agree to the terms and conditions, they are redirected to this page.
17. Click the APPLY button.
Your settings are saved.
Set up Facebook Wi-Fi
You can set up Facebook Wi-Fi on your Orbi WiFi network to offer your customers free
WiFi access if they check in to your existing Facebook business page.
User Manual93Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
ATTENTION: If a user attempts to access a website over HTTP (by default, over port
80), the user is directed to the Facebook Login page. If a user attempts to accesses a
secure website over HTTPS (by default, over port 443), a Security Waning window opens
in their web browser. The user must click the Allow button on the Security Warning
window to see the see the Facebook Login page.
To set up Facebook Wi-Fi:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the Orbi admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Guest Portal.
The Guest Portal Settings page displays.
5. Select the Enable Guest Portal check box.
6. Select the Enable SSID Broadcast check box.
By default, this check box is selected. Allowing the router to broadcast its WiFi
network name (SSID) makes it easier to find your network and connect to it. If you
clear this check box, that creates a hidden network.
7. To change the network name, type a new name in the Guest Portal Network Name
(SSID) field.
The name can be up to 32 characters long and it is case-sensitive. If you change the
name, make sure to write down the new name and keep it in a safe place.
8. In the Authentication Mode section, select the Facebook Wi-Fi radio button.
The page adjust and displays the Add Page button.
9. Click the Add Page button.
The Facebook Login page displays.
10. Log in to your Facebook business account.
The Facebook Wi-Fi Configuration page displays.
User Manual94Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
11. On the Facebook Wi-Fi Configuration page, do the following:
a. From the Select a Page menu, select a Facebook business page.
b. Select the bypass mode option:
•Skip check-in link. To allow customers to skip check-in, select the Skip
check-in link radio button.
If you enable this option, users can either check in to the selected Facebook
business page or skip the check-in.
•Require Wi-Fi code. To require users to enter a WiFi code before they can
gain WiFi access, select the Require Wi-Fi code radio button and type a WiFi
code in the field that displays.
If you enable this option, users can either check in to the selected Facebook
business page or skip the check-in by using the WiFi code.
c. From the Session Length menu, select the period after which users are
automatically logged out.
d. To add terms of service to the Facebook check-in page, select the Terms of
Service check box and type or copy the terms of service.
e. Click the Save Settings button.
The Facebook Wi-Fi settings are saved.
The name of the selected Facebook business page displays in the Facebook
Page field in the router web interface along with the Change Page button, which
lets you replace the selected Facebook business page with another one.
f. Return to the Guest Portal Settings page in the router web interface.
12. On the Guest Portal Settings page, click the APPLY button.
Your settings are saved.
Manage the download bandwidth per SSID
You can set up four WiFi networks for your Orbi Pro network: one for administrative
access, one for employee access, one for Internet of things (IoT) devices, and one for
guest access. You can manage the download bandwidth per WiFi network (SSID) by
assigning a percentage of the total bandwidth (100 percent) to each SSID. The available
download bandwidth on an SSID determines the network priority for devices connected
to the SSID.
If the download bandwidth usage on an SSID exceeds the assigned bandwidth for the
SSID, the router limits the bandwidth on the SSID, which might affect the download
speed for devices connected to the SSID.
User Manual95Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
In setting the download bandwidth ratio for an SSID, consider the number and type of
devices that connect to the SSID and the typical download bandwidth usage for those
devices. For example, more devices might connect to the IoT WiFi network than to the
employee network, but the typical bandwidth usage for IoT devices might be lower
than for employee devices.
Note: The router does not control the uplink bandwidth, that is, the bandwidth from
devices to the router.
To set the download bandwidth ratios for the SSIDs:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the router admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Wireless.
The Wireless Settings page displays the admin WiFi settings.
Note: Even though this is the page for the admin WiFi settings, the bandwidth ratios
that you specify on this page apply to the admin WiFi network, employee WiFi
network, IoT WiFi network, and guest WiFi network. (All bandwidth ratios together
must add up to 100 percent.) Similarly, if you specify bandwidth ratios on the
employee WiFi settings page, IoT WiFi settings page, or the guest WiFi network
page, they also apply to all other WiFi networks.
5. Select the Enable Bandwidth per SSID check box.
In the Bandwidth per SSID graphic, the colored icons are enabled.
6. Specify the bandwidth ratios by moving the icons on the bandwidth line.
The icons represent the following WiFi networks:
•Blue. Admin WiFi network (Wireless 1).
•Green. Employee WiFi network (Wireless 2).
•Purple. IoT WiFi network (Wireless 3).
•Gray. Guest WiFi network.
User Manual96Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
As you move an icon, the bandwidth ratio for the WiFi network changes and the
percentage displays in the icon.
All bandwidth ratios together add up to 100 percent of the available download
bandwidth. If you change one ratio, the ratio for another WiFi network might also
change.
7. Click the Apply button.
Your settings are saved. The router sends the new settings to the satellite.
View or change advanced WiFi settings
To view or change advanced WiFi settings:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Wireless Settings.
The Advanced Wireless Settings page displays.
Note: The backhaul password is a security key that is used in WiFi communication
between the router and the satellite. For information about generating a new backhaul
password, see Generate a new backhaul password on page 99.
5. In the Region list, select your region.
In some locations, you cannot change this setting.
6. To control the SSID broadcast, select or clear the Enable SSID Broadcast check
box.
When this check box is selected, the router broadcasts its network name (SSID) so
that it displays when you scan for local WiFi networks on your computer or WiFi
device.
7. Click the Apply button.
Your settings are saved.
User Manual97Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Use the router as a WiFi access point
You can set up the router to run as an access point (AP) on the same local network as
another router or gateway.
For example, you can use the Orbi router as a WiFi access point that connects to a
gateway or modem router that you already use for your Internet service. In this situation,
you do not need to change the settings for the gateway or modem router.
To set up the Orbi router as an AP after you set up your Internet connection:
1. Use an Ethernet cable to connect the Internet port of this router to a LAN port on
your existing router or gateway.
2. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
3. Enter orbilogin.com.
A login window opens.
4. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
5. Select ADVANCED > Advanced Setup > Router/AP Mode.
The Router/AP Mode page displays.
6. Select the AP Mode radio button.
The page adjusts.
7. Select the IP address setting:
•Get dynamically from existing router. The other router on the network assigns
an IP address to this router while this router is in AP mode.
•Enable fixed IP settings on this device (not recommended). Use this setting
if you want to manually assign a specific IP address to this router while it is in AP
mode. Using this option effectively requires advanced network experience.
Note: To avoid interference with other routers or gateways in your network, we
recommend that you use different WiFi settings on each router. You can also turn
off the WiFi radio on the other router or gateway and use the Orbi only for WiFi client
access.
User Manual98Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
8. Click the Apply button.
The IP address of the router changes, and you are disconnected.
9. To reconnect, close and restart your browser and enter orbilogin.com.
Set up router mode
If you set up your router as an access point, you can change it back to a router.
To set up the Orbi router as a router:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Router/AP Mode.
The Router/AP Mode page displays.
5. Select the Router Mode radio button.
The page adjusts.
6. Click the Apply button.
Your settings are saved.
Generate a new backhaul password
The backhaul password is a security key that is used in WiFi communication between
the router and the satellite. You can generate a new backhaul password. After you
generate a new backhaul password, you must use the Sync button to build a new
backhaul connection so that the router and satellite can communicate with each other
using WiFi.
User Manual99Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
To generate a new backhaul password:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Wireless Settings.
The Advanced Wireless Settings page displays.
5. In the Backhaul Password section, click the GENERATE button.
The router generates a new backhaul password.
Enable or disable implicit beamforming
Implicit beamforming means that the router can use information from client devices
that support beamforming to improve the WiFi signal.
To enable or disable implicit beamforming:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Wireless Settings.
The Advanced Wireless Settings page displays.
5. To enable Implicit beamforming, select the Enable Implicit BEAMFORMING check
box.
6. To disable Implicit beamforming, clear the Enable Implicit BEAMFORMING check
box.
User Manual100Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
7. Click the Apply button.
Your settings are saved.
If you connected over WiFi to the network, you are disconnected from the network
and must reconnect.
Enable or disable MU-MIMO
Multiuser multiple input, multiple output (MU-MIMO) improves performance when
multiple MU-MIMO-capable WiFi clients transfer data at the same time. WiFi clients
must support MU-MIMO, and they must be connected to a 5 GHz WiFi band.
To enable or disable MU-MIMO:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Wireless Settings.
The Advanced Wireless Settings page displays.
5. To enable or disable daisy-chain topology, do one of the following:
•To enable MU-MIMO, select the Enable MU-MIMO check box.
•To disable MU-MIMO, clear the Enable MU-MIMO check box.
6. Click the Apply button.
Your settings are saved.
If you connected over WiFi to the network, you are disconnected from the network
and must reconnect.
User Manual101Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Enable or disable Protected Management
Frames
Protected Management Frames (PMF), according to the 802.11w standard, is a security
feature that protects unicast and multicast management frames from being intercepted
and changed for malicious purposes.
The PMF feature is disabled by default, but you can enable it as a requirement for
management frames. However, some legacy devices might not be capable of supporting
PMF and might not be able to connect. As a solution, you can enable PMF as optional,
which lets the router activate PMF based on whether devices can support PMF.
Make sure that you understand the technology before enabling this feature.
Note: If you enable PMF, some incompatible client devices might disconnect. If you
use the combined WPA-PSK [TKIP] + WPA2-PSK [AES] security option and configure
PMF as a requirement, PMF might not take effect.
To enable or disable PMF:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Wireless Settings.
The Advanced Wireless Settings page displays.
5. At the bottom of the page, make one of the following selections from the Protected
Management Frames (802.11w) menu:
•Disable. PMF is disabled. This is the default settings.
•Optional. PMF is optional for all WiFi networks.
•Required. PMF is required.
Your selection applies to all WiFi networks on the router and satellites.
6. Click the Apply button.
User Manual102Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Your settings are saved.
Check your Internet bandwidth
You can use Ookla Speedtest to detect your Internet bandwidth.
To check your Internet bandwidth using Speedtest:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Speedtest.
The Speedtest page displays.
5. Click the Take a Speedtest button.
Your Internet’s download and upload speeds display.
Set up a bridge for a port group or VLAN tag
group
Some devices, such as an IPTV, cannot function behind the router’s Network Address
Translation (NAT) service or firewall. Based on what your Internet service provider (ISP)
requires, for the device to connect to the ISP’s network directly, you can enable the
bridge between the device and the router’s Internet port or add new VLAN tag groups
to the bridge.
Note: If your ISP provides directions on how to set up a bridge for IPTV and Internet
service, follow those directions.
Note: This feature is only supported if the router is in router mode.
User Manual103Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Set up a bridge for a port group
If the devices that are connected to the router’s Ethernet port an IPTV device, your ISP
might require you to set up a bridge for a port group for the router’s Internet interface.
A bridge with a port group prevents packets that are sent between the IPTV device and
the router’s Internet port from being processed through the router’s network address
translation (NAT) service.
To configure a port group and enable the bridge:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > VLAN/Bridge Settings.
The VLAN/IPTV Setup page displays.
5. Select the Enable VLAN/Bridge Setup check box.
The page expands.
6. Select the By bridge group radio button.
7. In the Wired Ports section, select the Ethernet port on the router that your device
is connected to.
8. To enable the VLAN ID, select the Enable VLAN ID check box and enter a value
from 1 to 4094.
9. Click the Apply button.
Your settings are saved.
Set up a bridge for a VLAN tag group
If the devices that are connected to the router’s Ethernet LAN ports include an IPTV
device, your ISP might require you to set up a bridge for a VLAN tag group for the
router’s Internet interface.
If you are subscribed to IPTV service, the router might require VLAN tags to distinguish
between the Internet traffic and the IPTV traffic. A bridge with a VLAN tag group prevents
User Manual104Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
packets that are sent between the IPTV device and the router’s Internet port from being
processed through the router’s Network Address Translation (NAT) service.
You can add VLAN tag groups to a bridge and assign VLAN IDs and priority values to
each VLAN tag group.
To add a VLAN tag group and enable the bridge:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the Orbi admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > VLAN/Bridge Settings.
The VLAN/Bridge Settings page displays.
5. Select the Enable VLAN/Bridge Group check box.
The page expands.
6. Select the By VLAN tag group radio button.
The section expands.
7. Click the Add button.
The Add VLAN Rule page displays.
8. Specify the settings as described in the following table.
DescriptionField
Enter a name for the VLAN tag group.
The name can be up to 10 characters.
Name
Enter a value from 1 to 4094.VLAN ID
User Manual105Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
(Continued)
DescriptionField
Enter a value from 0 to 7.Priority
Select the check box for a wired Ethernet port.
If your device is connected to an Ethernet port on the router, select the Ethernet port check box that
corresponds to the Ethernet port on the router to which the device is connected.
You must select at least one Ethernet port. You can select more than one port.
9. Click the Add button.
The VLAN tag group is added.
10. Click the Apply button.
Your settings are saved.
Improve network connections with Universal
Plug and Play
Universal Plug and Play (UPnP) helps devices, such as Internet appliances and computers,
access the network and connect to other devices as needed. UPnP devices can
automatically discover the services from other registered UPnP devices on the network.
If you use applications such as multiplayer gaming, peer-to-peer connections, or real-time
communications such as instant messaging or remote assistance, enable UPnP.
To enable Universal Plug and Play:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > UPnP.
The UPnP page displays.
User Manual106Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
5. Select the Turn UPnP On check box.
By default, this check box is selected. UPnP for automatic device configuration can
be enabled or disabled. If the Turn UPnP On check box is cleared, the router does
not allow any device to automatically control router resources, such as port
forwarding.
6. Type the advertisement period in minutes.
The advertisement period specifies how often the router broadcasts its UPnP
information. This value can range from 1 to 1440 minutes. The default period is 30
minutes. Shorter durations ensure that control points receive current device status
at the expense of more network traffic. Longer durations can compromise the
freshness of the device status but can significantly reduce network traffic.
7. Type the advertisement time to live in hops.
The time to live for the advertisement is measured in hops (steps) for each UPnP
packet sent. Hops are the steps a packet takes between routers. The number of hops
can range from 1 to 255. The default value for the advertisement time to live is 4
hops, which should be fine for most home networks. If you notice that some devices
are not being updated or reached correctly, it might be necessary to increase this
value.
8. Click the Apply button.
The UPnP Portmap Table displays the IP address of each UPnP device that is accessing
the router and which ports (internal and external) that device opened. The UPnP
Portmap Table also displays what type of port is open and whether that port is still
active for each IP address.
9. To refresh the information in the UPnP Portmap Table, click the Refresh button.
User Manual107Specify Network Settings
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
6
Manage Your Network
This chapter describes the router settings for administering and maintaining your router
and home network.
The chapter includes the following sections:
• Update the router and satellite firmware
• Change the admin password
• Enable admin password reset
• Reset the admin password
• View router status and usage information
• Display Internet port statistics
• Check the Internet connection status
• View satellites, WiFi devices, and wired devices connected to the Orbi network
• View satellite status
• View and manage logs of router activity
• Set up a syslog server
• Monitor Internet traffic
• Manage the router configuration file
• Set up remote management
• Use remote access
108
Update the router and satellite firmware
You can use the router web interface to check if new firmware is available and update
your router and satellite, or you can manually update the firmware for your router and
satellite.
Enable the automatic firmware update feature
You can let the router automatically update its firmware and the firmware for any Orbi
satellites on the network.
To enable the automatic firmware update feature:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the router admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Administration > Firmware Update.
The Firmware Update page displays.
5. In the Orbi Router Auto Firmware Update section, select the Enable radio button.
6. Click the Apply button.
Your settings are saved.
Check for firmware updates
To check for new firmware and update your router and satellite:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the router admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
User Manual109Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
The BASIC Home page displays.
4. Select ADVANCED > Administration > Firmware Update > Online Update.
The Firmware Update page displays.
5. Click the Check button.
The router checks to see if new firmware is available for the router and satellite.
6. If new firmware is available, click the Update All button.
The router locates and downloads the firmware for the router and satellite and begins
the update.
Note: To avoid the risk of corrupting the firmware, do not interrupt the upgrade.
For example, do not close the browser, click a link, or load a new page. Do not turn
off the router or satellite.
When the upload is complete, your router and satellite restart. The update process
typically takes about one minute. Read the new firmware release notes to find out if
you must reconfigure the router after updating.
Manually update firmware
If a satellite is connected to your router, you can log in to the router to manually upload
the firmware on your satellite.
WARNING: We recommend that you always update the firmware on your satellite first,
and then update your router. Also, do not update the firmware on your router and
satellite at the same time, and do not update more than one Orbi device (router or
satellite) at a time. If you need to update more than one Orbi device, wait for the first
Orbi device to finish updating before updating your next Orbi device.
To manually update the firmware on your Orbi router and satellite, follow these
high level steps:
1. Visit netgear.com/support and download the firmware for both your Orbi router and
satellite.
2. Update the firmware on your Orbi satellite.
For more information, see Manually update satellite firmware on page 111.
3. Update the firmware on your Orbi router.
For more information, see Manually update router firmware on page 111.
User Manual110Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Manually update satellite firmware We recommend that you update your
satellite’s firmware before you update the router’s firmware.
To manually update your satellite’s firmware:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the router admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Administration > Firmware Update > Manual Update.
The Firmware Update page displays.
5. Select the check box next to your satellite’s model name.
If you have more than one satellite, only update one satellite at a time. You must wait
for the first satellite to finish updating before updating the next satellite.
6. Click the Update button.
The Orbi satellite Firmware Update window opens.
7. If the browser ask you for the admin password, enter the same password that you
entered for the router.
8. Click the BROWSE button.
9. Locate and select the satellite firmware file that you downloaded.
The firmware file name ends in .img or .chk.
10. Click the UPLOAD button.
It takes a few minutes to complete the process.
11. After Orbi satellite finishes updating, select Status and double-check the firmware
version on the Status page.
The firmware on your Orbi satellite is updated.
Manually update router firmware We recommend that you update your router’s
firmware after you update the satellite’s firmware.
WARNING: Make sure that your satellite completes its firmware update before you
update your router’s firmware.
User Manual111Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
To manually update your router’s firmware:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Administration > Firmware Update > Manual Update.
The Firmware Update page displays.
5. Click the Browse button.
6. Locate and select the router firmware file you downloaded.
The firmware file name ends in .img.
7. Click the Upload button.
The firmware is updated.
Change the admin password
This feature let you change the default password that is used to log in to the router with
the user name admin. This password is not the one that you use to access the Orbi WiFi
network.
Note: Be sure to change the password for the user name admin to a secure password.
The ideal password contains no dictionary words from any language and contains
uppercase and lowercase letters, numbers, and symbols. It can be up to 30 characters.
To set the password for the user name admin:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
User Manual112Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Administration > Set Password.
The Set Password page displays.
5. Type the old password, and type the new password twice.
6. To be able to reset the password, select the Enable Password Reset check box.
We recommend that you enable password reset.
7. Click the Apply button.
Your settings are saved.
Enable admin password reset
The router admin password is used to log in to your router web interface. We recommend
that you enable the password reset feature so that you can reset the password if it is
forgotten. This reset process is supported in Internet Explorer, Firefox, and Chrome
browsers but not in the Safari browser.
To enable password reset:
1. Launch a web browser from a computer or WiFi device that is connected to the
network.
2. Enter http://www.routerlogin.net.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Administration > Set Password.
The Set Password page displays.
5. Select the Enable Password Reset check box.
6. Select two security questions and provide answers to them.
7. Click the Apply button.
Your settings are saved.
User Manual113Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Reset the admin password
If you set up the password reset feature, you can reset your router admin password if
you forgot it.
To reset your admin password:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Click the Cancel button.
If password reset is enabled, you are prompted to enter the router's serial number.
You can find the router's serial number on the router label.
4. Enter the router's serial number in the field.
5. Click the Continue button.
You are requested to enter a new admin password and to set new security questions.
6. Enter your new admin password, set new security questions, and click the Next
button.
Your settings are saved.
7. Click the Login button.
A login window opens.
8. With your new admin password, log in to the router.
View router status and usage information
To view router status and usage information:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
User Manual114Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Click the ADVANCED tab.
The ADVANCED Home page displays the router status.
Display Internet port statistics
To display Internet port statistics:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Click the ADVANCED tab.
5. In the Internet Port pane, click the Show Statistics button.
The Show Statistics window opens and displays following information:
•System Up Time. The time elapsed since the router was last restarted.
•Port. The statistics for the WAN (Internet) and LAN (Ethernet) ports. For each
port, the page displays the following information:
-Status. The link status of the port.
-TxPkts. The number of packets transmitted on this port since reset or manual
clear.
-RxPkts. The number of packets received on this port since reset or manual
clear.
-Collisions. The number of collisions on this port since reset or manual clear.
-Tx B/s. The current transmission (outbound) bandwidth used on the WAN
and LAN ports.
-Rx B/s. The current reception (inbound) bandwidth used on the WAN and
LAN ports.
User Manual115Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
-Up Time. The time elapsed since this port acquired the link.
-Poll Interval. The interval at which the statistics are updated in this page.
6. To change the polling frequency, enter a time in seconds in the Poll Interval field
and click the Set Interval button.
7. To stop the polling entirely, click the Stop button.
Check the Internet connection status
To check the Internet connection status:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Click the ADVANCED tab.
5. In the Internet Port pane, click the Connection Status button.
The Connection Status window opens and displays the following information
•IP Address. The IP address that is assigned to the router.
•Subnet Mask. The subnet mask that is assigned to the router.
•Default Gateway. The IP address for the default gateway that the router
communicates with.
•DHCP Server. The IP address for the Dynamic Host Configuration Protocol server
that provides the TCP/IP configuration for all the computers that are connected
to the router.
•DNS Server. The IP address of the Domain Name Service server that provides
translation of network names to IP addresses.
•Lease Obtained. The date and time when the lease was obtained.
•Lease Expires. The date and time that the lease expires.
6. To return the status of all items to 0, click the Release button.
User Manual116Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
7. To refresh the page, click the Renew button.
8. To exit the page, click the Close Window button.
View satellites, WiFi devices, and wired
devices connected to the Orbi network
You can view all satellites, WiFi devices, and wired devices that are connected to your
Orbi network.
To view devices connected to your network:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the router admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Attached Devices.
The Attached Devices page displays.
The Wired Devices table displays the following information:
•Device Name. The device model, name, type, and IP address.
•IP Address. The device IP address. The device’s IP address can change because
the router assigns an IP address to each device when it joins the network.
•MAC Address. The device MAC address. The unique MAC address for each
device does not change.
•Connection Type. The device is connected to the Orbi network through a wired
Ethernet connection.
•Connected Orbi. The Orbi router or satellite that the device is connected to. The
Orbi router’s or satellite’s MAC address also displays.
The Wireless Devices table displays the following information:
•Device Name. The device model, name, type, and IP address.
•IP Address. The device IP address. The device’s IP address can change because
the router assigns an IP address to each device when it joins the network.
User Manual117Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
•MAC Address. The device MAC address. The unique MAC address for each
device does not change.
•Channel. The channel on which the device is connected to the WiFi network.
•SSID. The radio band of the WiFi network to which the device is connected.
•Connected Orbi. The Orbi router or satellite that the device is connected to. The
Orbi router’s or satellite’s MAC address also displays.
•TX/RX Rate (Mbps). The average rate in Mbps at which the device transmits (TX)
and receives (RX) traffic.
•Association Time. The period in hours, minutes, and seconds that the device is
connected to the WiFi network.
•Link Status. The quality and strength in dBm of the WiFi connection of the device.
5. To update the page with the most recent information, click the Refresh button.
View satellite status
To view your satellite’s status, it must be connected to your Orbi network.
To view your satellite’s status:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the router admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Attached Devices.
The Attached Devices page displays.
5. In the Connected Satellites section, find your satellite’s IP address.
6. Enter your satellite’s IP address in your web browser’s address bar.
A login window opens.
7. Enter the same admin user name and password that you entered for the router.
The satellite’s status displays.
User Manual118Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
View and manage logs of router activity
The log is a detailed record of the websites users accessed or attempted to access and
many other router actions. You can specify which actions are logged. Up to 256 entries
can be stored in the log.
To view and manage logs:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Administration > Logs.
The Logs page displays the following information:
•Date and time. The date and time the log entry was recorded.
•Source IP. The IP address of the initiating device for this log entry.
•Target address. The name or IP address of the website or news group visited or
to which access was attempted.
•Action. The action that occurred, such as whether Internet access was blocked
or allowed.
5. To manage the actions that the router logs, check or clear the check boxes for the
following actions:
•Attempted access to allowed sites. Selected by default.
•Attempted access to blocked sites and services. Selected by default.
•Connections to the Web-based interface of this Router. Selected by default.
•Router operation (startup, get time etc). Selected by default.
•Known DoS attacks and Port Scans. Selected by default.
•Port Forwarding / Port Triggering. Selected by default.
•Wireless access. Selected by default.
User Manual119Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
•VPN Service. Selected by default.
•Insight. Cleared by default.
6. To refresh the log page, click the Refresh button.
7. To clear the log entries, click the Clear Log button.
8. To email the log immediately, click the Send Log button.
Set up a syslog server
If a syslog server is present on your network, you can configure the router to send its
system logs to the syslog server.
To enable the syslog function and specify the syslog server:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the router admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Advanced > Administration > Logs.
The Logs page displays.
5. At the bottom of the page, in the Syslog Server section, select the Enable Syslog
radio button.
The Syslog fields become available.
6. Specify the IP address and port number for the syslog server:
•Syslog Server IP Address. Enter the IP address of the syslog server on your
network.
•Syslog Port. Enter the port number through with the router can reach the syslog
server. By default, the port number is 514.
7. Click the Apply button.
Your settings are saved. The router send its logs to the syslog server.
User Manual120Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Monitor Internet traffic
Traffic metering allows you to monitor the volume of Internet traffic that passes through
the router Internet port. You can set limits for traffic volume.
To monitor Internet traffic:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Traffic Meter.
The Traffic Meter page displays.
5. Select the Enable Traffic Meter check box.
6. To control the volume of Internet traffic, use either the traffic volume control feature
or the connection time control feature:
•Select the Traffic volume control by radio button and then select one of the
following options:
-No Limit. No restriction is applied when the traffic limit is reached.
-Download only. The restriction is applied to incoming traffic only.
-Both Directions. The restriction is applied to both incoming and outgoing
traffic.
•Select the Connection time control radio button and enter the allowed hours
in the Monthly limit field.
7. If your ISP charges for extra data volume when you make a new connection, enter
the extra data volume in MB in the Round up data volume for each connection by
field.
8. In the Traffic Counter section, set the traffic counter to begin at a specific time and
date.
To start the traffic counter immediately, click the Restart Counter Now button.
User Manual121Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
9. If you want the router to issue a warning message before the monthly limit of Mbytes
or hours is reached, in the Traffic Control section, enter a numeric value.
By default, the value is 0 and no warning message is issued.
10. To stop the Internet connection when the limit is attained, select the Disconnect
and disable the Internet connection check box.
11. Click the Apply button.
The Internet Traffic Statistics section helps you to monitor the data traffic.
12. To update the Internet Traffic Statistics section, click the Refresh button.
13. To display more information about the data traffic on your router and to change the
poll interval, click the Internet Traffic Status button.
Manage the router configuration file
The configuration settings of the router are stored within the router in a configuration
file. You can back up (save) this file to your computer, restore it, or reset it to the factory
default settings.
Back up settings
To back up the router’s configuration settings:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Administration > Backup Settings.
The Backup Settings page displays.
5. Click the BACK UP button.
6. Specify a location on your network.
A copy of the current settings is saved in the location you specified.
User Manual122Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Manage the automatic backup options
You can let the router automatically back up configuration settings before a firmware
upgrade.
You can also schedule an automatic backup at a regular interval.
To manage the automatic backup options:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Administration > Backup Settings.
The Backup Settings page displays.
5. To let the router automatically back up configuration settings before a firmware
upgrade, select the Backup before upgrade check box.
6. To schedule automatic backups, next to Back up periodically, enter the a number
from 1 to 365 in the Day(s) field.
If you enter 1, the backup occurs daily, if you enter 2, the backup occurs every other
day, and so on. By default, the entry is 0 and no automatic backup occurs.
7. Click the Apply button.
Your settings are saved.
Erase the current configuration settings
You can erase the current configuration and restore the factory default settings. You
might want to do this if you move the router to a different network.
To erase the configuration settings:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
User Manual123Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Administration > Backup Settings.
The Backup Settings page displays.
5. Click the ERASE button.
The factory default settings are restored. The user name is admin, the password is
password, and the LAN IP address is 192.168.1.1. DHCP is enabled.
Restore configuration settings
To restore configuration settings that you backed up:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Administration > Backup Settings.
The Backup Settings page displays.
5. Click the Browse button to find and select the .cfg file.
6. Click the RESTORE button.
The file is uploaded to the router and the router reboots.
WARNING: Do not interrupt the reboot process.
User Manual124Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Set up remote management
You can access your router over the Internet to view or change its settings. You must
know the router’s WAN IP address to use this feature. For information about Dynamic
DNS, see Manage Dynamic DNS on page 67.
Note: Be sure to change the password for the user name admin to a secure password.
The ideal password contains no dictionary words from any language and contains
uppercase and lowercase letters, numbers, and symbols. It can be up to 30 characters.
See Change the admin password on page 112.
To set up remote management:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Remote Management.
The Remote Management page displays.
5. Select the Turn Remote Management On check box.
6. In the Allow Remote Access By section, specify the external IP addresses to be allowed
to access the router’s remote management.
Note: For enhanced security, restrict access to as few external IP addresses as is
practical.
Select one of the following:
•To allow access from a single IP address on the Internet, select the Only This
Computer radio button. Enter the IP address to be allowed access.
•To allow access from a range of IP addresses on the Internet, select the IP Address
Range radio button. Enter a beginning and ending IP address to define the
allowed range.
•To allow access from any IP address on the Internet, select the Everyone radio
button.
User Manual125Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
7. Specify the port number for accessing the router.
Normal web browser access uses the standard HTTP service port 80. For greater
security, enter a custom port number for the remote router access. Choose a number
from 1024 to 65535, but do not use the number of any common service port. The
default is 8080, which is a common alternate for HTTP.
8. Click the Apply button.
Your settings are saved.
Use remote access
To use remote access:
1. Launch a web browser on a computer that is not on your home network.
2. Type your router’s WAN IP address into your browser’s address or location field
followed by a colon (:) and the custom port number.
For example, if your external address is 134.177.0.123 and you use port number
8080, enter http://134.177.0.123:8080 in your browser.
User Manual126Manage Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Manage port forwarding to a local server
If your home network includes a server, you can allow certain types of incoming traffic
to reach the server. For example, you might want to make a local web server, FTP server,
or game server visible and available to the Internet.
The router can forward incoming traffic with specific protocols to computers on your
local network. You can specify the servers for applications and you can also specify a
default DMZ server to which the router forwards all other incoming protocols.
Set up port forwarding to a local server
To forward specific incoming protocols:
1. Decide which type of service, application, or game you want to provide.
2. Find the local IP address of the computer on your network that will provide the
service.
The server computer must always use the same IP address. To specify this setting,
use the reserved IP address feature. See Manage reserved LAN IP addresses on
page 75.
3. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
4. Enter orbilogin.com.
A login window opens.
5. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
6. Select ADVANCED > Advanced Setup > Port Forwarding/Port Triggering.
The Port Forwarding/Port Triggering page displays.
7. Leave the Port Forwarding radio button selected as the service type.
8. In the Service Name menu, select the service name.
If the service that you want to add is not in the list, create a custom service. See Add
a custom port forwarding service on page 129.
9. In the Server IP Address field, enter the IP address of the computer that will provide
the service.
10. Click the Add button.
User Manual128Customize Internet Traffic Rules
for Ports
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
The service displays in the list.
Add a custom port forwarding service
To add a custom service:
1. Find out which port number or range of numbers the application uses.
You can usually find this information by contacting the publisher of the application
or user groups or news groups.
2. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
3. Enter orbilogin.com.
A login window opens.
4. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
5. Select ADVANCED > Advanced Setup > Port Forwarding/Port Triggering.
The Port Forwarding/Port Triggering page displays.
6. Leave the Port Forwarding radio button selected as the service type.
7. Click the Add Custom Service button.
The Ports - Custom Services page displays.
8. In the Service Name field, enter a descriptive name.
9. In the Protocol menu, select the protocol.
If you are unsure, select TCP/UDP.
10. In the External Port range field, enter the port numbers.
11. Specify the internal ports by one of these methods:
•Leave the Use the same port range for Internal port check box selected.
•Type the port numbers in the Internal port range field.
12. Type the IP address in the Internal IP address fields or select the radio button for
an attached device listed in the table.
13. Click the Apply button.
The service is now in the list on the Port Forwarding/Port Triggering page.
User Manual129Customize Internet Traffic Rules
for Ports
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Edit a port forwarding service
To edit a port forwarding entry:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Port Forwarding/Port Triggering.
The Port Forwarding/Port Triggering page displays.
5. Leave the Port Forwarding radio button selected as the service type.
6. In the table, select the radio button next to the service name.
7. Click the Edit Service button.
The Ports - Custom Services page displays.
8. Specify changes to any of the following settings:
•Service Name. Type the service name.
•Protocol. If you are unsure, select TCP/UDP.
•External port range.
•For the internal ports, leave the Use the same port range for Internal port check
box selected or enter the ports in the Internal port range field.
•Internal IP address. Type the IP address in the Internal IP address fields, or
select the radio button for an attached device listed in the table.
9. Click the Apply button.
Your settings are saved.
User Manual130Customize Internet Traffic Rules
for Ports
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Delete a port forwarding entry
To delete a port forwarding entry:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Port Forwarding/Port Triggering.
The Port Forwarding/Port Triggering page displays.
5. Select the Port Forwarding radio button as the service type.
6. In the table, select the radio button next to the service name.
7. Click the Delete Service button.
Application example: Make a local web server public
If you host a web server on your local network, you can use port forwarding to allow
web requests from anyone on the Internet to reach your web server.
To make a local web server public:
1. Assign your web server either a fixed IP address or a dynamic IP address using DHCP
address reservation.
In this example, your router always gives your web server an IP address of
192.168.1.33.
2. In the Port Forwarding/Port Triggering page, configure the router to forward the
HTTP service to the local address of your web server at 192.168.1.33.
HTTP (port 80) is the standard protocol for web servers.
3. (Optional) Register a host name with a Dynamic DNS service, and specify that name
on the Dynamic DNS page of the router.
Dynamic DNS makes it much easier to access a server from the Internet because you
can type the name in the Internet browser. Otherwise, you must know the IP address
that the ISP assigned, which typically changes.
User Manual131Customize Internet Traffic Rules
for Ports
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
How the router implements the port forwarding rule
The following sequence shows the effects of a port forwarding rule:
1. When you type the URL www.example.com in your browser, the browser sends a
web page request message with the following destination information:
•Destination address. The IP address of www.example.com, which is the address
of your router.
•Destination port number. 80, which is the standard port number for a web server
process.
2. Your router receives the message and finds your port forwarding rule for incoming
port 80 traffic.
3. The router changes the destination in the message to IP address 192.168.1.123 and
sends the message to that computer.
4. Your web server at IP address 192.168.1.123 receives the request and sends a reply
message to your router.
5. Your router performs Network Address Translation (NAT) on the source IP address,
and sends the reply through the Internet to the computer or WiFi device that sent
the web page request.
Manage port triggering
Port triggering is a dynamic extension of port forwarding that is useful in these cases:
•An application must use port forwarding to more than one local computer (but not
simultaneously).
•An application must open incoming ports that are different from the outgoing port.
With port triggering, the router monitors traffic to the Internet from an outbound “trigger”
port that you specify. For outbound traffic from that port, the router saves the IP address
of the computer that sent the traffic. The router temporarily opens the incoming port
or ports that you specify in your rule and forwards that incoming traffic to that destination.
Port forwarding creates a static mapping of a port number or range of ports to a single
local computer. Port triggering can dynamically open ports to any computer when
needed and close the ports when they are no longer needed.
User Manual132Customize Internet Traffic Rules
for Ports
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Add a port triggering service
To add a port triggering service:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Port Forwarding/Port Triggering.
The Port Forwarding/Port Triggering page displays.
5. Select the Port Triggering radio button.
The page adjusts.
6. Click the Add Service button.
The Port Triggering - Services page displays.
7. In the Service Name field, type a descriptive service name.
8. In the Service User menu, select Any, or select Single address and enter the IP
address of one computer:
•Any (the default) allows any computer on the Internet to use this service.
•Single address restricts the service to a particular computer.
9. Select the service type, either TCP or UDP or TCP/UDP (both).
If you are not sure, select TCP/UDP.
10. In the Triggering Port field, enter the number of the outbound traffic port that will
open the inbound ports.
11. Enter the inbound connection port information in the Connection Type,Starting
Port, and Ending Port fields.
12. Click the Apply button.
The service is now in the Portmap Table. You must enable port triggering before
the router used port triggering for the service that you added. See Enable port
triggering on page 134.
User Manual133Customize Internet Traffic Rules
for Ports
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Enable port triggering
To enable port triggering:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > Port Forwarding/Port Triggering.
The Port Forwarding/Port Triggering page displays.
5. Select the Port Triggering radio button.
The page adjusts.
6. Clear the Disable Port Triggering check box.
If this check box is selected, the router does not use port triggering even if you
specified port triggering settings.
7. In the Port Triggering Timeout field, enter a value up to 9999 minutes.
This value controls how long the inbound ports stay open when the router detects
no activity. This value is required because the router cannot detect when the
application terminates.
Application example: Port triggering for Internet Relay Chat
Some application servers, such as FTP and IRC servers, send replies to multiple port
numbers. Using port triggering, you can tell the router to open more incoming ports
when a particular outgoing port starts a session.
An example is Internet Relay Chat (IRC). Your computer connects to an IRC server at
destination port 6667. The IRC server not only responds to your originating source port,
but also sends an “identify” message to your computer on port 113. Using port triggering,
you can tell the router, “When you initiate a session with destination port 6667, you must
User Manual134Customize Internet Traffic Rules
for Ports
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
also allow incoming traffic on port 113 to reach the originating computer.” The following
sequence shows the effects of the port triggering rule you define:
1. You open an IRC client program to start a chat session on your computer.
2. Your IRC client composes a request message to an IRC server using a destination
port number of 6667, the standard port number for an IRC server process. Your
computer then sends this request message to your router.
3. Your router creates an entry in its internal session table describing this communication
session between your computer and the IRC server. Your router stores the original
information, performs Network Address Translation (NAT) on the source address
and port, and sends this request message through the Internet to the IRC server.
4. Noting your port triggering rule and observing the destination port number of 6667,
your router creates another session entry to send any incoming port 113 traffic to
your computer.
5. The IRC server sends a return message to your router using the NAT-assigned source
port (for example, port 33333) as the destination port. The IRC server also sends an
“identify” message to your router with destination port 113.
6. When your router receives the incoming message to destination port 33333, it checks
its session table to see if a session is active for port number 33333. Finding an active
session, the router restores the original address information replaced by NAT and
sends this reply message to your computer.
7. When your router receives the incoming message to destination port 113, it checks
its session table and finds an active session for port 113 associated with your
computer. The router replaces the message’s destination IP address with your
computer’s IP address and forwards the message to your computer.
8. When you finish your chat session, your router eventually senses a period of inactivity
in the communications. The router then removes the session information from its
session table, and incoming traffic is no longer accepted on port numbers 33333 or
113.
User Manual135Customize Internet Traffic Rules
for Ports
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
8
Use VPN to Access Your Network
You can use OpenVPN software to remotely access your router using virtual private
networking (VPN). This chapter explains how to set up and use VPN access.
This chapter includes the following sections:
• Set up a VPN connection
• Specify VPN service in the router
• Install OpenVPN software
• Use a VPN tunnel on your Windows-based computer
• Use VPN to access your Internet service at home
136
Set up a VPN connection
A virtual private network (VPN) lets you use the Internet to securely access your network
when you aren’t home.
This type of VPN access is called a client-to-gateway tunnel. The computer is the client,
and the router is the gateway. To use the VPN feature, you must log in to the router and
enable VPN, and you must install and run VPN client software on the computer.
VPN uses DDNS or a static IP address to connect with your router.
To use a DDNS service, register for an account with a host name (sometimes called a
domain name). You use the host name to access your network. The router supports
these accounts: NETGEAR, No-IP, and Dyn.
If your Internet service provider (ISP) assigned a static WAN IP address (such as 50.196.x.x
or 10.x.x.x) that never changes to your Internet account, the VPN can use that IP address
to connect to your home network.
Specify VPN service in the router
You must specify the VPN service settings in the router before you can use a VPN
connection.
To specify the VPN service:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > VPN Service.
The VPN Service page displays.
5. Select the Enable VPN Service check box.
By default, the VPN uses the UDP service type and uses port 12974. If you want to
customize the service type and port, we recommend that you change these settings
before you install the OpenVPN software.
User Manual137Use VPN to Access Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
6. To change the service type, scroll down and select the TCP radio button.
7. To change the port, scroll down to the Service Port field, and type the port number
that you want to use.
8. Click the Apply button.
Your settings are saved. VPN is enabled in the router, but you must install and set
up OpenVPN software on your computer before you can use a VPN connection.
Install OpenVPN software
You must install this software on each Windows-based computer, Mac computer, iOS
device, or Android device that you plan to use for VPN connections to your router.
Install OpenVPN software on your Windows-based
computer
You must install this software on each Windows-based computer that you plan to use
for VPN connections to your router.
To install VPN client software on your Windows-based computer:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > VPN Service.
The VPN Service page displays.
5. Make sure that the Enable VPN Service check box is selected.
6. Specify any VPN service settings on the page.
For more information, see Specify VPN service in the router on page 137.
7. Click the For Windows button to download the OpenVPN configuration files.
8. Visit openvpn.net/index.php/download/community-downloads.html to download
the OpenVPN client utility.
User Manual138Use VPN to Access Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
9. In the Windows Installer section of the page, double-click the
openVPN-install-xxx.exe link.
10. Download and install the Open VPN software on your computer, click the
openVPN-install-xxx.exe file.
11. Click the Next button.
12. When prompted, read the License Agreement and click the I Agree button.
13. Leave the check boxes selected, and click the Next button.
14. To specify the destination folder, click the Browse button and select a destination
folder.
User Manual139Use VPN to Access Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
15. Click the Install button.
The window displays the progress of the installation and then displays the final
installation page.
16. Click the Finish button.
17. Unzip the configuration files that you downloaded and copy them to the folder where
the VPN client is installed on your device.
For a client device with Windows 64-bit system, the VPN client is installed at
C:\Programfiles\OpenVPN\config\ by default.
18. For a client device with Windows, modify the VPN interface name to NETGEAR-VPN:
a. On your computer, go to the Networks page. If you are using Windows 10, select
Control Panel > Network and Sharing Center > Change adapter settings.
b. In the local area connection list, find the local area connection with the device
name TAP-Windows Adapter.
c. Select the local area connection and change its name (not its device name) to
NETGEAR-VPN.
If you do not change the VPN interface name, the VPN tunnel connection will fail.
User Manual140Use VPN to Access Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
For more information about using OpenVPN on your Windows-based computer,
visit
https://openvpn.net/index.php/open-source/documentation/howto.html#quick.
Install OpenVPN software on your Mac computer
You must install this software on each Mac computer that you plan to use for VPN
connections to your router.
To install VPN client software on your Mac computer:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > VPN Service.
The VPN Service page displays.
5. Make sure that the Enable VPN Service check box is selected.
6. Specify any VPN service settings on the page.
For more information, see Specify VPN service in the router on page 137.
7. Click the FOR MAC OS button to download the OpenVPN configuration files.
8. Visit https://tunnelblick.net/index.html to download the OpenVPN client utility for
Mac OS X.
9. Download and install the file.
10. Unzip the configuration files that you downloaded and copy them to the folder where
the VPN client is installed on your device.
The client utility must be installed by a user with administrative priviledges.
For more information about using OpenVPN on your Mac computer, visit
https://openvpn.net/vpn-server-resources/installation-guide-for-openvpn-connect-client-on-macos/.
User Manual141Use VPN to Access Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Install OpenVPN software on an iOS device
You must install this software on each iOS device that you plan to use for VPN connections
to your router.
To install VPN client software on an iOS device:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > VPN Service.
The VPN Service page displays.
5. Make sure that the Enable VPN Service check box is selected.
6. Specify any VPN service settings on the page.
For more information, see Specify VPN service in the router on page 137.
7. Click the FOR SMART PHONE button to download the OpenVPN configuration
files.
8. On your iOS device, download and install the OpenVPN Connect app from the Apple
app store.
9. On your computer, unzip the configuration files that you downloaded and send the
files to your iOS device.
Note that when you open the .ovpn file, a list of apps displays. Select the OpenVPN
Connect app to open the .ovpn file.
For more information about using OpenVPN on your iOS device, visit
http://www.vpngate.net/en/howto_openvpn.aspx#ios.
Install OpenVPN software on an Android device
You must install this software on each Android device that you plan to use for VPN
connections to your router.
User Manual142Use VPN to Access Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
To install VPN client software on an Android device:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > VPN Service.
The VPN Service page displays.
5. Make sure that the Enable VPN Service check box is selected.
6. Specify any VPN service settings on the page.
For more information, see Specify VPN service in the router on page 137.
7. Click the FOR SMART PHONE button to download the OpenVPN configuration
files.
8. On your Android device, download and install the OpenVPN Connect app from the
Google Play Store.
9. On your computer, unzip the configuration files that you downloaded and send the
files to your Android device.
10. Open the files on your Android device.
11. Open the .ovpn file using the OpenVPN Connect app.
For more information about using OpenVPN on your Android device, visit
http://www.vpngate.net/en/howto_openvpn.aspx#android.
Use a VPN tunnel on your Windows-based
computer
After you set up the router to use VPN and install the OpenVPN application on your
computer, you can open a VPN tunnel from your computer to your router over the
Internet.
For the VPN tunnel to work, the local LAN IP address of the remote router must use a
different LAN IP scheme from that of the local LAN where your VPN client computer is
User Manual143Use VPN to Access Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
connected. If both networks use the same LAN IP scheme, when the VPN tunnel is
established, you cannot access your home router or your home network with the
OpenVPN software.
The default LAN IP address scheme for the router is 192.x.x.x.The most common IP
schemes are 192.x.x.x, 172.x.x.x, and 10.x.x.x. If you experience a conflict, change the
IP scheme either for your home network or for the network with the client VPN computer.
For information about changing these settings, see Change the LAN TCP/IP settings on
page 71.
To open a VPN tunnel:
1. Launch the OpenVPN application with administrator privileges.
Figure 5. The OpenVPN icon displays in the Windows taskbar.
TIP: You can create a shortcut to the VPN program, then use the shortcut to access
the settings and select the run as administrator check box. Then every time you
use this shortcut, OpenVPN automatically runs with administrator privileges.
2. Right-click the OpenVPN icon.
3. Select Connect.
The VPN connection is established. You can launch a web browser and log in to your
router.
User Manual144Use VPN to Access Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Use VPN to access your Internet service at
home
When you’re away from home and you access the Internet, you usually use a local Internet
service provider. For example, at a coffee shop you might be given a code that lets you
use the coffee shop’s Internet service account to surf the web.
Orbi Pro lets you use a VPN connection to access your own Internet service when you’re
away from home. You might want to do this if you travel to a geographic location that
doesn’t support all the Internet services that you use at home. For example, your Netflix
account might work at home but not in a different country.
Set up VPN client Internet access in the router
By default, the router is set up to allow VPN connections only to your home network,
but you can change the settings to allow Internet access. Accessing the Internet remotely
through a VPN might be slower than accessing the Internet directly.
To allow VPN clients to use your home Internet service:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > VPN Service.
The VPN Service page displays.
5. Select the Enable VPN Service radio button.
6. Scroll down to the Clients will use this VPN connection to access section, and select
the All sites on the Internet & Home Network radio button.
When you access the Internet with the VPN connection, instead of using a local
Internet service, you use the Internet service from your home network.
7. Click the Apply button.
Your settings are saved.
User Manual145Use VPN to Access Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
8. Click the FOR WINDOWS or FOR MACOSX button and download the configuration
files for your VPN clients.
9. Unzip the configuration files and copy them to the folder where the VPN client is
installed on your device.
For a client device with Windows 64-bit system, the VPN client is installed at
C:\Programfiles\OpenVPN\config\ by default.
Block VPN client Internet access in the router
By default, the router is set up to allow VPN connections only to your home network,
not to the Internet service for your home network. If you changed this setting to allow
Internet access, you can change it back.
To allow VPN clients to access only your home network:
1. Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Advanced Setup > VPN Service.
The VPN Service page displays.
5. Select the Enable VPN Service radio button.
6. Scroll down to the Clients will use this VPN connection to access section, and select
the Home Network only radio button.
This is the default setting.The VPN connection is only to your home network, not to
the Internet service for your home network.
7. Click the Apply button.
Your settings are saved.
8. Click the FOR WINDOWS or FOR MAC0SX button and download the configuration
files for your VPN clients.
9. Unzip the configuration files and copy them to the folder where the VPN client is
installed on your device.
User Manual146Use VPN to Access Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
For a client device with Windows 64-bit system, the VPN client is installed at
C:\Programfiles\OpenVPN\config\ by default.
Use a VPN tunnel to access your Internet service at home
To access your Internet service:
1. Set up the router to allow VPN access to your Internet service.
See Specify VPN service in the router on page 137.
2. On your computer, launch the OpenVPN application.
The OpenVPN icon displays in the Windows taskbar.
3. Right-click the icon and select Connect.
4. When the VPN connection is established, launch your Internet browser.
User Manual147Use VPN to Access Your Network
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
9
Troubleshooting
This chapter provides information to help you diagnose and solve problems you might
experience with your Orbi router or satellite. If you do not find the solution here, check
the NETGEAR support site at support.netgear.com for product and contact information.
This chapter includes the following sections:
• Quick tips
• The router and satellite do not sync
• You cannot log in to the router
• You cannot access the Internet
• Troubleshoot Internet browsing
• Troubleshoot PPPoE
• Troubleshoot WiFi connectivity
• Troubleshoot your network using the ping utility
148
Quick tips
This section describes tips for troubleshooting some common problems.
Sequence to restart your network
When you restart your network, follow this sequence:
1. Turn off and unplug the modem.
2. Turn off the router.
3. Plug in the modem and turn it on. Wait two minutes.
4. Turn on the router and wait two minutes.
WiFi settings
Make sure that the WiFi settings in the WiFi-enabled computer or mobile device and
the router match.
The WiFi network name (SSID) and WiFi security settings must match exactly.
If you set up an access list, you must add each WiFi-enabled computer or mobile device’s
MAC address to the router’s access list.
Network settings
Make sure that the network settings of the computer are correct. Wired and wirelessly
connected computers must use network (IP) addresses on the same network as the
router. The simplest way to do this is to configure each computer to obtain an IP address
automatically using DHCP.
Some cable modem service providers require you to use the MAC address of the
computer initially registered on the account. You can view the MAC address on the
Attached Devices page.
The router and satellite do not sync
If you are experiencing difficulty syncing the router and the satellite, we recommend
that you move the satellite into the same room as the router during the sync. Then move
the satellite to a different location.
User Manual149Troubleshooting
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
To sync the router and the satellite:
1. Place the satellite in the same room as the Orbi router.
Use this satellite location only during the sync process.
2. Connect the satellite to a power source.
3. If the Power LED on the back of the satellite does not light, press the Power On/Off
button.
4. Wait for the satellite’s ring LED to light solid white or magenta.
5. Press the Sync button on the router and then within two minutes, press the Sync
button on the satellite.
6. Wait for the satellite to sync with the router.
The satellite’s ring LED pulses white while it attempts to sync with the router. After
the LED bar pulses white, it lights one of the following colors for about three minutes
and then turns off:
•Blue. The Orbi router and satellite successfully synced, and the connection
between the router and satellite is good.
•Amber. The Orbi router and satellite successfully synced, but the connection
between the router and satellite is only fair. Consider moving the Orbi satellite
closer to the Orbi router.
•Magenta. The Orbi router and satellite did not sync.
7. Do one of the following:
•The sync failed. If the sync failed, try to sync again by repeating Step 5 and Step
6. If the sync keeps failing, try a different location or position.
•The sync is successful. If the sync is successful, move the satellite to the location
where you want to install it and continue with Step 8.
8. At the new location, connect the satellite to a power source.
9. At the new location, resync the satellite with the router by repeating Step 5 and Step
6.
If the satellite’s ring LED lights blue or amber, the satellite synced successfully. If the
satellite’s ring LED lights blue, the connection is good. If the satellite’s ring LED bar
lights amber, consider moving the satellite closer to the router so that you can get
a good connection instead of a fair connection.
User Manual150Troubleshooting
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
10. If the satellite’s ring LED lights magenta, the satellite did not resync with the router.
If they successfully synced when they were placed in the same room, do one of the
following:
•Move the satellite closer to the router and try again. The router must be within
the satellite’s WiFi cover area for a good or fair connection to the satellite.
•Place another satellite between the router and the satellite that you are trying to
sync. Then try to sync between the two satellites. With daisy chain networking,
your satellites can connect to each other or to the router, depending on which
connection is best.
You cannot log in to the router
Make sure that your computer or mobile device is connected to the Orbi WiFi network.
If you do not want to use a WiFi connection, you can connect your computer to the Orbi
router with an Ethernet cable.
If you changed the admin password and you forgot what it is, see Reset the admin
password on page 114.
You cannot access the Internet
Check your network and Internet connections:
1. Make sure that your WiFi-enabled computer or mobile device is connected to the
Orbi network.
2. If you are connected to Orbi but you cannot access the Internet, check to see if your
Internet connection is working.
3. Launch a web browser from a computer or WiFi device that is connected to the
network.
4. Enter orbilogin.com.
A login window opens.
5. Enter the router admin user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home page displays.
6. Click the ADVANCED tab.
The ADVANCED Home page displays.
User Manual151Troubleshooting
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
7. Check that an IP address is shown for the Internet port.
If 0.0.0.0 is shown, your router did not obtain an IP address from your Internet service
provider (ISP).
If your router cannot obtain an IP address from the ISP, you can force your cable or DSL
modem to recognize your new router by restarting your network. For more information,
see Sequence to restart your network on page 149.
If your router is still unable to obtain an IP address from the ISP, the problem might be
one of the following:
•Your Internet service provider (ISP) might require a login program. Ask your ISP
whether they require PPP over Ethernet (PPPoE) or some other type of login.
•If your ISP requires a login, the login name and password might be set incorrectly.
•Your ISP might check for your computer’s host name. Assign the computer host
name of your ISP account as the account name on the Internet Setup page.
•If your ISP allows only one Ethernet MAC address to connect to Internet and checks
for your computer’s MAC address, do one of the following:
-Inform your ISP that you bought a new network device and ask them to use the
router’s MAC address.
-Configure your router to clone your computer’s MAC address.
Troubleshoot Internet browsing
If your router can obtain an IP address but your computer is unable to load any web
pages from the Internet, it might be for one of the following reasons:
•The traffic meter is enabled, and the limit was reached.
By configuring the traffic meter not to block Internet access when the traffic limit is
reached, you can resume Internet access. If your ISP sets a usage limit, they might
charge you for the overage.
•Your computer might not recognize any DNS server addresses. A DNS server is a
host on the Internet that translates Internet names (such as www addresses) to numeric
IP addresses.
Typically, your ISP provides the addresses of one or two DNS servers for your use.
If you entered a DNS address during the router’s configuration, restart your computer.
Alternatively, you can configure your computer manually with a DNS address, as
explained in the documentation for your computer.
•The router might not be configured as the default gateway on your computer.
User Manual152Troubleshooting
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Reboot the computer and verify that the router address (www.routerlogin.net) is
listed by your computer as the default gateway address.
•You might be running login software that is no longer needed. If your ISP provided
a program to log you in to the Internet (such as WinPoET), you no longer need to
run that software after installing your router.You might need to go to Internet Explorer
and select Tools > Internet Options, click the Connections tab, and select Never
dial a connection. Other browsers provide similar options.
Troubleshoot PPPoE
If you are using PPPoE, try troubleshooting your Internet connection.
To troubleshoot a PPPoE connection:
1. Launch a web browser from a computer or WiFi device that is connected to the
network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the router admin user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home page displays.
4. Click the ADVANCED tab.
The ADVANCED Home page displays.
5. In the Internet Port pane, click the Connection Status button.
The Connection Status window opens.
6. Check the Connection Status window to see if your PPPoE connection is active and
working.
If the router is not connected, click the Connect button.
The router continues to attempt to connect indefinitely.
7. If you cannot connect after several minutes, the router might be set up with an
incorrect service name, user name, or password, or your ISP might be experiencing
a provisioning problem.
Unless you connect manually, the router does not authenticate using PPPoE until
data is transmitted to the network.
User Manual153Troubleshooting
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Troubleshoot WiFi connectivity
If you are experiencing trouble connecting to the Orbi WiFi network, try to isolate the
problem:
•Does the WiFi-enabled computer or mobile device that you are using find your WiFi
network?
If you disabled the router’s SSID broadcast, then your WiFi network is hidden and
does not display in the list of networks that your computer or WiFi device finds. (By
default, SSID broadcast is enabled.)
•Does your WiFi-capable device support the security that you are using for your WiFi
network (WPA or WPA2)?
•To view the WiFi settings for the router, use an Ethernet cable to connect a computer
to a LAN port on the router. Then log in to the router, and select BASIC > Wireless.
Note: Be sure to click the Apply button if you change settings.
•If you are trying to connect to the 5 GHz 1 or 5 GHz 2 band, does your WiFi-enabled
computer or mobile device support this standard?
•Did your computer or WiFi device automatically connect to a different WiFi network
in your area, such as a WiFi hotspot?
Troubleshoot your network using the ping
utility
Most network devices and routers contain a ping utility that sends an echo request
packet to the designated device. The device then responds with an echo reply. You can
easily troubleshoot a network using the ping utility in your computer or workstation.
Test the LAN path to your router
You can ping the router from your computer to verify that the LAN path to your router
is set up correctly.
To ping the router from a Windows computer:
1. From the Windows toolbar, click the Start button and select Run.
2. In the field provided, type ping followed by the IP address of the router, as in this
example:
User Manual154Troubleshooting
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
ping www.routerlogin.net
3. Click the OK button.
You should see a message like this one:
Pinging <IP address > with 32 bytes of data
If the path is working, you see this message:
Reply from < IP address >: bytes=32 time=NN ms TTL=xxx
If the path is not working, you see this message:
Request timed out
If the path is not functioning correctly, you might be experiencing one of the following
problems:
•Wrong physical connections
For a wired connection, make sure that the numbered LAN port LED is lit for the port
to which you are connected.
Check that the appropriate LEDs are on for your network devices. If your router and
computer are connected to a separate Ethernet switch, make sure that the link
LEDs are lit for the switch ports that are connected to your computer and router.
•Wrong network configuration
Verify that the Ethernet card driver software and TCP/IP software are both
installed and configured on your computer.
Verify that the IP address for your router and your computer are correct and that
the addresses are on the same subnet.
Test the path from your computer to a remote device
After verifying that the LAN path works correctly, test the path from your computer to
a remote device.
To test the path from your computer to a remote device:
1. From the Windows toolbar, click the Start button and select Run.
2. In the Windows Run window, type:
ping -n 10 <IP address>
where <IP address> is the IP address of a remote device such as your ISP DNS server.
If the path is functioning correctly, messages display that are similar to those shown in
Test the LAN path to your router on page 154.
User Manual155Troubleshooting
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
If you do not receive replies, check the following:
•Check to see that the IP address of your router is listed as the default gateway for
your computer. If DHCP assigns the IP configuration of your computers, this
information is not visible in your computer Network Control Panel. Verify that the IP
address of the router is listed as the default gateway.
•Check to see that the network address of your computer (the portion of the IP address
specified by the subnet mask) is different from the network address of the remote
device.
•Check to see that your cable or DSL modem is connected and functioning.
•If your ISP assigned a host name to your computer, enter that host name as the
account name on the Internet Setup page.
•Your ISP might be rejecting the Ethernet MAC addresses of all but one of your
computers.
Many broadband ISPs restrict access by allowing traffic only from the MAC address of
your broadband modem. Some ISPs additionally restrict access to the MAC address of
a single computer connected to that modem. If your ISP does this, configure your router
to “clone” or “spoof” the MAC address from the authorized computer.
User Manual156Troubleshooting
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Factory settings
The following factory settings information are for the Orbi Pro router (model SRR60)
and the Orbi Pro satellite (model SRS60).
You can return the Orbi Pro router or satellite to its factory settings. Use the end of a
paper clip or a similar object to press and hold the Reset button on the back of the
router or satellite for at least seven seconds. The router or satellite resets, and returns
to the factory settings.
Factory settings for Orbi Pro router model SRR60
The following table shows the factory default settings for the Orbi Pro router.
Table 4. Factory default settings for the router
Default SettingFeature
Router login
orbilogin.comUser login URL
adminUser name (case-sensitive)
passwordLogin password (case-sensitive)
Internet connection
Use default hardware addressWAN MAC address
1500WAN MTU size
AutoSensingPort speed
Local network (LAN)
192.168.1.1LAN IP
255.255.255.0Subnet mask
EnabledDHCP server
192.168.1.2 to 192.168.1.254DHCP range
192.168.1.2DHCP starting IP address
192.168.1.254DHCP ending IP address
DisabledDMZ
User Manual158Supplemental Information
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Table 4. Factory default settings for the router (Continued)
Default SettingFeature
GMT for WW, except NA and GR
GMT+1 for GR
GMT-8 for NA
Time zone
DisabledTime zone adjusted for daylight saving time
DisabledSNMP
Firewall
Disabled (except traffic on port 80, the HTTP port)Inbound (communications coming in from the Internet)
Enabled (all)Outbound (communications going out to the Internet)
DisabledSource MAC filtering
WiFi
EnabledWiFi communication
See router labelSSID name
WPA2-PSK (AES)Security
EnabledBroadcast SSID
Auto1
Transmission speed
United States in the US
Otherwise, varies by region
Country/region
AutoRF channel 2.4 GHz fronthaul
AutoRF channel 2.4 GHz backhaul
Channel 48 for NA, AU, and CA
Channel 36 for EU
RF channel 5 GHz fronthaul
Channel 48 for NA, AU, and CA
Channel 36 for EU
RF channel 5 GHz backhaul
1Maximum wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput can vary. Network
conditions and environmental factors, including volume of network traffic, building materials and construction, and
network overhead, lower actual data throughput rate.
User Manual159Supplemental Information
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Factory settings for Orbi Pro satellite model SRS60
The following table shows the factory default settings for the Orbi Pro satellite.
Table 5. Factory default settings for the satellite
Default SettingFeature
Router login
orbilogin.comUser login URL
adminUser name (case-sensitive)
passwordLogin password (case-sensitive)
Internet connection
Use default hardware addressWAN MAC address
1500WAN MTU size
AutoSensingPort speed
Local network (LAN)
192.168.1.250LAN IP
255.255.255.0Subnet mask
EnabledDHCP server
192.168.1.2 to 192.168.1.254DHCP range
192.168.1.2DHCP starting IP address
192.168.1.254DHCP ending IP address
DisabledDMZ
GMT for WW except NA and GR
GMT+1 for GR
GMT-8 for NA
Time zone
DisabledTime zone adjusted for daylight saving time
DisabledSNMP
Firewall
Disabled (except traffic on port 80, the HTTP port)Inbound (communications coming in from the Internet)
Enabled (all)Outbound (communications going out to the Internet)
DisabledSource MAC filtering
User Manual160Supplemental Information
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Table 5. Factory default settings for the satellite (Continued)
Default SettingFeature
WiFi
EnabledWiFi communication
See satellite labelSSID name
WPA2-PSK (AES)Security
EnabledBroadcast SSID
Auto2
Transmission speed
United States in the US
Otherwise, varies by region
Country/region
AutoRF channel 2.4 GHz fronthaul
AutoRF channel 2.4 GHz backhaul
Channel 48 for NA, AU, and CA
Channel 36 for EU
RF channel 5 GHz fronthaul
Channel 48 for NA, AU, and CA
Channel 36 for EU
RF channel 5 GHz backhaul
2Maximum wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput can vary. Network
conditions and environmental factors, including volume of network traffic, building materials and construction, and
network overhead, lower actual data throughput rate.
User Manual161Supplemental Information
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Technical specifications
The following are the technical specifications for Orbi Pro router (model SRR60) and
Orbi Pro satellite (SRS60).
Technical specifications for Orbi Pro router model SRR60
The following table shows the technical specifications for the router.
Table 6. Orbi Pro router specifications
DescriptionFeature
TCP/IP, RIP-1, RIP-2, DHCP, PPPoE, PPTP, Bigpond,
Dynamic DNS, UPnP, and SMB
Data and routing protocols
North America: 120V, 60 Hz, input
UK, Australia: 240V, 50 Hz, input
Europe: 230V, 50 Hz, input
All regions (output): 12V, 3.5A DC output
Power adapter
6.8 x 3.3 x 9.7in (174 x 85 x 247 mm)Dimensions
2.06 lb (0.93 kg)Weight
0° to 40°C (32º to 104ºF)Operating temperature
90% maximum relative humidity, noncondensingOperating humidity
FCC Part 15 Class B
VCCI Class B
EN 55 022 (CISPR 22), Class B C-Tick N10947
Electromagnetic emissions
10BASE-T or 100BASE-TX or 1000BASE-T, RJ-45LAN
10BASE-T or 100BASE-TX or 1000BASE-T, RJ-45WAN
Maximum wireless signal rate complies with the IEEE
802.11 standard.3
WiFi
2.4 GHz: Max. 400 Mbps
5 GHz Front haul: Max. 866 Mbps
5 GHz Back haul: Max. 1733 Mbps
Radio data rates
IEEE 802.11b/g/n 2.4 GHz–256 QAM support
IEEE 802.11a/n/ac 5 GHz-256 QAM support
Data encoding standards
Limited by the amount of WiFi network traffic generated
by each node (typically 50–70 nodes)
2.4 GHz: 127
5 GHz (front haul): 127
Maximum number of computers per wireless network
User Manual162Supplemental Information
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Table 6. Orbi Pro router specifications (Continued)
DescriptionFeature
2.412–2.462Operating frequency range 2.4 GHz (US)
2.412–2.472 GHzOperating frequency range 2.4 GHz (Europe ETSI)
5.18 GHz–5.24 GHz
5.745 GHz–5.825 GHz
Operating frequency range 5 GHz (US)
5.18 GHz–5.24 GHz
5.26 GHz–5.32 GHz
5.5 GHz-5.7 GHz
Operating frequency range 5 GHz (EU)
WPA2-PSK [AES]
WPA-PSK [TKIP] + WPA2-PSK [AES]
WPA2-Enterprise
802.11 security
3Maximum wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput can vary. Network
conditions and environmental factors, including volume of network traffic, building materials and construction, and
network overhead, lower actual data throughput rate.
Technical specifications for Orbi Pro satellite model SRS60
The following table shows the technical specifications for the satellite.
Table 7. Orbi Pro satellite specifications
DescriptionFeature
TCP/IP, RIP-1, RIP-2, DHCP, PPPoE, PPTP, Bigpond,
Dynamic DNS, UPnP, and SMB
Data and routing protocols
North America: 120V, 60 Hz, input
UK, Australia: 240V, 50 Hz, input
Europe: 230V, 50 Hz, input
All regions (output): 12V, 3.5A DC output
Power adapter
6.8 x 3.3 x 9.7in (174 x 85 x 247 mm)Dimensions
2.06 lb (0.93 kg)Weight
0° to 40°C (32º to 104ºF)Operating temperature
90% maximum relative humidity, noncondensingOperating humidity
FCC Part 15 Class B
VCCI Class B
EN 55 022 (CISPR 22), Class B C-Tick N10947
Electromagnetic emissions
10BASE-T or 100BASE-TX or 1000BASE-T, RJ-45LAN
User Manual163Supplemental Information
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60
Table 7. Orbi Pro satellite specifications (Continued)
DescriptionFeature
10BASE-T or 100BASE-TX or 1000BASE-T, RJ-45WAN
Maximum wireless signal rate complies with the IEEE
802.11 standard.4
WiFi
2.4 GHz: Max. 400 Mbps
5 GHz Front haul: Max. 866 Mbps
5 GHz Back haul: Max. 1733 Mbps
Radio data rates
IEEE 802.11b/g/n 2.4 GHz–256 QAM support
IEEE 802.11a/n/ac 5 GHz-256 QAM support
Data encoding standards
Limited by the amount of WiFi network traffic generated
by each node (typically 50–70 nodes).
2.4 GHz: 127
5 GHz (front haul): 127
Maximum number of computers per wireless network
2.412–2.462 GHzOperating frequency range 2.4 GHz (US)
2.412–2.472 GHzOperating frequency range 2.4 GHz (Europe ETSI)
5.18 GHz–5.24 GHz
5.745 GHz–5.825 GHz
Operating frequency range 5 GHz (US)
5.18 GHz–5.24 GHz
5.26 GHz–5.32 GHz
5.5 GHz-5.7 GHz
Operating frequency range 5 GHz (EU)
WPA2-PSK [AES]
WPA-PSK [TKIP] + WPA2-PSK [AES]
WPA2-Enterprise
802.11 security
4Maximum wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput can vary. Network
conditions and environmental factors, including volume of network traffic, building materials and construction, and
network overhead, lower actual data throughput rate.
User Manual164Supplemental Information
Orbi Pro Router SRR60 and Orbi Pro Satellite SRS60