Philips AC4081 User Manual

Displayed below is the user manual for AC4081 by Philips which is a product in the Air Purifiers category. This manual has pages.

Related Manuals

Philips MC-I250/22 Manual

Philips HQ8890 Manual

Philips HQ6849 Manual

Philips HQ6415 Manual

Philips MP3 Micro HiFi-System MCM250 Manual

Philips AJ3600/37 Manual

Philips HQ6707/16 Manual

Philips HQ8850 Manual

AC4080

AC4081

EN User manual 3 ZH-T 使用手冊 29

English

Contents

1 Important 4

Safety 4

2 Your combi air purier and

humidier 8

3 Getting started 9

Install lters 9

Prepare for humidication 10

4 Using the appliance 11

Understand the air quality light 11

Switch on and o the appliance 11

Change the working mode 12

Change the fan speed 13

Set the timer 15

Set the humidity level 15

Set the child lock 16

Water level 16

5 Cleaning 17

Cleaning schedule 17

Clean the body of the appliance 17

Clean the air quality sensor 17

Clean the water tank and

humidication lter 18

Clean the pre-lter and descale

the humidication lter 19

6 Replacing the lters 21

Understand the healthy air

protect lock 21

Replace lter 2 21

Replace the humidication lter 22

7 Resetting the lter lifetime

counter 23

8 Troubleshooting 24

9 Guarantee and service 26

Order parts or accessories 26

10 Notices 26

Electromagnetic elds (EMF) 26

Recycling 26

1 Important

Safety

Read this user manual carefully before

you use the appliance, and save it for

future reference.

Danger

• Do not let water or any

other liquid or flammable

detergent enter the

appliance to avoid electric

shock and/or a fire

hazard.

• Do not clean the

appliance with water,

any other liquid, or a

(flammable) detergent to

avoid electric shock and/

or a fire hazard.

• Do not spray any

flammable materials

such as insecticides or

fragrance around the

appliance.

• The water in the water

tank is not suitable for

drinking. Do not drink this

water and do not use it to

feed animals or to water

plants. When you empty

the water tank, pour the

water down the drain.

Warning

• Check if the voltage

indicated on the bottom

indicated at the rear of the

appliance corresponds to

the local power voltage

before you connect the

appliance.

• If the power cord is

damaged, you must have

it replaced by Philips, a

service center authorized

by Philips, or similarly

qualified persons in order

to avoid a hazard.

• Do not use the appliance

if the plug, the power

cord, or the appliance

itself is damaged.

• This appliance can be

used by children aged

from 8 years and above

and persons with reduced

physical, sensory or

mental capabilities or

lack of experiences and

knowledge if they have

been given supervision or

instruction concerning use

of the appliance in a safe

way and understand the

hazards involved. Children

shall not play with the

appliance. Cleaning and

English

user maintenance shall

not be made by children

without supervision.

• Do not block the air inlet

and outlet, e.g. by placing

items on the air outlet or

in front of the air inlet.

Caution

• This appliance is not

a substitute for proper

ventilation, regular

vacuum cleaning, or use

of an extractor hood or

fan while cooking.

• If the power socket used

to power the appliance

has poor connections,

the plug of the appliance

becomes hot. Make

sure that you plug the

appliance into a properly

connected power socket.

• Always place and use the

appliance on a dry, stable,

level, and horizontal

surface.

• Leave at least 20cm free

space behind and on both

sides of the appliance

and leave at least 30cm

free space above the

appliance.

• Do not place anything

on top of the appliance

and do not sit on the

appliance.

• Do not place the

appliance directly below

an air conditioner to

prevent condensation

from dripping onto the

appliance.

• Make sure all filters

are properly installed

before you switch on the

appliance.

• Only use the original

Philips filters specially

intended for this

appliance. Do not use any

other filters.

• Avoid knocking against

the appliance (the air inlet

and outlet in particular)

with hard objects.

• Always lift or move

the appliance by both

handles at the sides of the

appliance.

• Do not insert your fingers

or objects into the air

outlet or the air inlet to

prevent physical injury

or malfunctioning of the

appliance.

• Do not use this appliance

when you have used

indoor smoke-type insect

repellents or in places

with oily residues, burning

incense, or chemical

fumes.

• Do not use the appliance

near gas appliances,

heating devices or

fireplaces.

• Always unplug the

appliance after use

and before filling water,

cleaning, or carrying out

other maintenance.

• Do not use the appliance

in a room with major

temperature changes,

as this may cause

condensation inside the

appliance.

• To prevent interference,

place the appliance

at least 2m away from

electrical appliances that

use airborne radio waves

such as TVs, radios, and

radio-controlled clocks.

• When the appliance is

not used for a long time,

bacteria may grow on the

filters. Check the filters

after a long period of

disuse. If the filters are

very dirty, replace them

(see the chapter ‘Replace

the filters’).

• The appliance is only

intended for household

use under normal

operating conditions.

• Do not use the appliance

in wet surroundings or in

surroundings with high

ambient temperatures,

such as the bathroom,

toilet, or kitchen.

• The appliance does

not remove carbon

monoxide (CO) or

radon (Rn). It cannot be

used a safety device in

case of accidents with

combustion processes

and hazardous chemicals.

• Clean the water tank

every day to keep it clean.

• Only fill the water tank

with cold tap water. Do

not use ground water or

hot water.

• Do not put any substance

other than water in the

water tank. Do not put

fragrance in the water

tank.

English

• If you do not use the

humidification function

for a long time, clean

the water tank and

humidification filter tray.

Dry the humidification

filter.

• If you need to move the

appliance, disconnect the

appliance from the power

supply first. Then empty

the water tank. Carry the

appliance horizontally by

both handles on the sides

of the appliance.

• Unplug the appliance

during filling and cleaning.

2 Your combi air purifier and humidifier

Congratulations on your purchase, and welcome to Philips!

To fully benefit from the support that Philips offers, register your product at

www.philips.com/welcome.

Philips VitaShield IPS technology and NanoCloud technology ensures you "Healthy air

always".

VitaShield IPS technology effectively remove pollutants (ultrafine particles, allergens,

bacteria and viruses) with size >0.02 micron including bacteria and virus*.

NanoCloud technology, using a special humidification filter adds H2O molecules

to the dry air, and produces healthy humid air without formation of water mist. Its

humidification filter retains bacteria, calcium and other particles from the water.

*According to 2008 Microbiological Risk Assessment Report of the World Health

Organization (WHO), the avian influenza, human influenza viruses, Legionella,

Hepatitus viruses and SARS coronavirus are larger than 0.02 micron.

Read this user manual carefully before you use the appliance, and save it for future

reference.

Filter 1: Pre-filter

Filter 3:

Humidification

filter AC4155

Water tank

Filter 2: 2-in-1 HEPA & Active

carbon filter AC4158

(for AC4080) Filter 2: Integrated

Multi-care filter AC4168

(for AC4081)

Air quality

sensor

English

3 Getting started

Install filters

The appliance comes with all filters

fitted inside. Remove the packaging

of the filters before you can use the

appliance. Remove all filters, unpack

them, and place them back into the

appliance described as follows:

Tip

•When you remove or insert filters, place

the appliance against a wall for more

stability.

Note

•Insert the filters in the correct position.

•Make sure that you place filter 2 in the

appliance first and then the pre-filter.

•Make sure that the side with the tag is

pointing towards you.

1 Unlock the bottom of the front

panel from the appliance, then

gently pull the top part of the front

panel towards you.

2 To remove the pre-filter, press the

two clips down and pull the filter

towards you.

3 Remove filter 2 from the appliance.

AC4080 AC4081

4 Remove the packaging materials of

filter 2.

5 Put the unpacked filter 2 back into

the appliance.

AC4080 AC4081

6 Put the pre-filter back into the

appliance.

AC4080 AC4081

Note

•Make sure that the side with the two

clips is pointing towards you, and that

all hooks of the pre-filter are properly

attached to the purifier.

7 To reattach the front panel, mount

the panel onto the top of the

appliance first (1). Then, gently

place the panel against the body of

the appliance (2).

Prepare for

humidification

1 Remove all packaging materials of

the humidification filter.

2 Pull out the water tank from the

side of the appliance.

3 Fill the water tank with cold tap

water.

English

Note

•When pouring water into the water tank,

make sure not to exceed the MAX water

level indication.

4 Put the humidification filter into the

water tank.

5 Push the water tank back into the

appliance.

4 Using the

appliance

Understand the air

quality light

Color of the air

quality light

Air quality level

Blue Good

Purple Fair

Red Bad

The air quality light automatically goes

on when the appliance is switched on,

and shows all colors repeatedly. In a

short while the air quality light selects

the color that corresponds to the

ambient air quality.

Note

•The built-in air quality sensor measures

the air quality and automatically selects

the appropriate color of the air quality

light. When the air is clean, the color of

the air quality light is in blue. When the

air quality deteriorates, the color of the

air quality light changes to purple or red.

Switch on and off the

appliance

The appliance operates under

air purification combined with

humidification by default.

1 Put the plug into the wall socket.

»All lights go on once and then go

out again.

Note

•After the appliance is switched off by the

on/off button , if the plug is still in the

power socket, the appliance will resume

working based on the last settings when

it is switched on again.

Change the working

mode

Besides operating under air purification

combined with humidification, the

appliance can also work under air

purification only mode.

1 After the appliance is switched on,

press once.

»The HUMIDIFY and humidity

level indicators go out.

»The humidification function is

deactivated. The appliance works

under air purification only mode.

2 Press again to activate the

humidification function.

Note

•In air purification only mode, the

humidification button does not

respond.

•The appliance cannot work under

humidification only mode.

2 Press to switch on the appliance.

»The PURIFY and HUMIDIFY lights

are on.

»After measuring the air quality

for a short while, the air quality

sensor automatically selects

the appropriate color of the air

quality light.

»The appliance enters AUTO mode,

and the target humidity level is

50% by default.

3 Press for 2 seconds to switch off

the appliance.

2”

English

Set the sensitivity of the air

quality sensor

This appliance allows you to adjust

the sensitivity of the air quality sensor.

There are three sensitivity levels:

• standard (default setting)

• sensitive

• extra sensitive

You can adjust the sensitivity of the air

quality sensor in the following way:

Note

•When the appliance is set to a higher

sensitivity, the purifier becomes more

allergic to the pollutants in the air. When

the purifier is in AUTO mode, it is more

likely to choose a higher fan speed

than the standard mode. The air quality

sensor selects the appropriate color of

the air quality light in accordance with

the higher sensitivity.

1 Unplug the appliance.

2 After a short while, put the plug in the

wall socket again.

3 Press and hold the fan speed

button and humidifier button

simultaneously for 3 seconds.

»One or more fan speed lights

flash to show the current

sensitivity level of the air quality

sensor.

3”

Fan speed light Sensitivity level

+ standard

sensitive

extra sensitive

4 Press the fan speed button to

adjust the sensitivity level of the air

quality sensor.

5 Press and hold for 2 seconds to

save the setting and switch off the

appliance.

Note

•When you are changing the sensitivity

level, if you do not change any settings,

or if you do not press for 2 seconds

after you have changed any settings, the

appliance will resume normal work without

saving any changes.

•After the sensitivity is changed and

saved, the appliance automatically starts

operating at the preset sensitivity level

whenever you switch on the appliance.

Change the fan speed

AUTO

In AUTO mode, the appliance

selects the appropriate fan speed in

accordance with the ambient air quality.

• Press the fan speed button to

select AUTO mode.

• AUTO and one of the fan speed

indicators ( , or ) light up.

Note

•In AUTO mode, when the air quality

reaches the target (air purification only

mode), or when the air quality and

humidity reach the target simultaneously

(combi mode), the appliance will work

with a lower fan speed, and the fan

speed indicator ( , or ) goes out.

Manual

You can mannually select the desired

fan speed.

• Press the fan speed button once

or more times to select the desired

fan speed ( , or ).

Note

•Fan speed is available for AC4081

only.

•In Manual mode, when the air quality

reaches the target (air purification only

mode), or when the air quality and

humidity reach the target simultaneously

(combi mode), the appliance will

continue to work with the selected fan

speed.

Tip

•If the air quality light is in blue color, this

means the air quality is good, and you

can select a lower fan speed.

•On the other hand, if the air quality light

is in red or purple color, this means the

air quality is bad or fair. You can select a

higher fan speed to clean the air quickly.

Sleep mode

In sleep mode, the appliance operates

very quietly.

• Press the fan speed button to

select the sleep mode.

»The sleep indicator lights up.

To change to another fan speed, press

the fan speed button .

Note

•When the appliance switches to sleep

mode, the indicators goes out after

1 minute, and the appliance keeps

working.

English

Set the timer

With the timer function, you can let the

appliance operate for a set number of

hours. When the set time has elapsed,

the appliance automatically switches

off.

1 Press the timer button to activate

the timer.

»The timer light ( , or ) goes

on.

2 Press the timer button repeatedly

to choose the number of hours you

want the appliance to operate. The

corresponding timer light goes on.

To deactivate the timer function, press

the timer button repeatedly until the

timer light ( , or ) goes out.

Set the humidity level

Note

•

Make sure that the water tank is filled

with water when you want to use the

humidification function (see the chapter

"Get started", section "Prepare for

humidification").

• Press the humidity button once

or more times to set the desired air

humidity to 40%, 50% or 60%.

»The corresponding humidity light

(40%, 50% or 60%) starts to flash.

»When the appliance reaches

the target humidity level, the

humidity level indicator remains

on.

Note

•If you want to increase the humidity

level in shorter time, you can select a

higher fan speed.

Set the child lock

Note

•Child lock is only applicable for AC4081.

• Press and hold the fan speed

button and timer button

simultaneously for 3 seconds to

activate child lock.

3”

»When the child lock is on, all

buttons are not responsive.

• Press and hold the fan speed

button and timer button

simultaneously for 3 seconds again

to deactivate child lock.

3”

Note

•When the child lock is on, the appliance

will not respond when you press any

button.

Water level

The water level in the water tank is

visible through the water level window

on the side of the appliance. When

there is not enough water in the water

tank, flashes to indicate that you have

to refill the water tank.

Note

•When there is no water in the water tank,

the refill water light remains on, and

the humidification indicator flashes to

remind users the humidification function

is not working. When the water tank is

refilled with water, the humidification

function will be resumed.

•The refill water light does not light up

under air purification only mode.

English

5 Cleaning

Note

•Always unplug the appliance before you

clean it.

•Never immerse the appliance in water or

any other liquid.

•Never use abrasive, aggressive, or

flammable cleaning agents such as

bleach or alcohol to clean any part of

the appliance.

•Only the pre-filter and humidification

filter are washable. The air purifier filter is

not washable nor vacuum cleanable.

Cleaning schedule

Frequency Cleaning method

When

necessary

Wipe the surface of the

appliance with a soft dry

cloth.

Every week Rinse the humidication lter.

Rinse the water tank.

When the

filter replace

indicator /

lights up

Clean the pre-filter.

Descale the

humidification filter

with the vinegar-water

mixture.

Every two

months

Clean the air quality

sensor and air humidity

sensor with a dry cotton

swab.

Clean the body of the

appliance

Regularly clean the inside and outside

of the appliance to prevent dust from

collecting.

1 Wipe away dust with a soft dry cloth

from the body of the appliance.

2 Clean the air inlet and the air outlet

with a soft dry cloth.

Clean the air quality

sensor

Clean the air quality sensor every two

months for optimal functioning of the

appliance. Clean it more frequently

if you use the appliance in a dusty

environment.

Note

•When the humidity level in the

room is very high, it is possible that

condensation develops on the air

quality sensor. As a result, the air quality

light may indicate that the air quality is

bad even though the air quality is good.

In this case you have to clean the air

quality sensor or use one of the manual

speed settings.

1 Clean the inlet and outlet of the air

quality sensor with a soft brush.

2 Remove the cover of the air quality

sensor.

3 Clean the sensor, the dust inlet

and the dust outlet with a lightly

moistened cotton swab.

4 Dry them with a dry cotton swab.

5 Reattach the sensor cover.

Clean the water tank and

humidification filter

Clean the water tank and humidification

filter every week to keep them hygienic.

1 Pull the water tank from the side of

the appliance.

2 Remove the humidification filter

from the water tank.

3 Rinse the humidification filter under

a running tap.

English

Note

•Do not scrub the humidification filter,

nor place it under direct sunlight.

4 Unfasten the locks on the edge of

the water tank lid, and remove it

from the water tank.

5 Rinse the water tank under a

running tap.

Note

•If necessary, use a mild detergent to

clean the water tank. In this case, rinse

the water tank thoroughly.

6 Dry the water tank and its lid with a

soft, dry cloth.

7 Put the lid back onto the water tank

and fasten the locks.

8 Put the humidification filter back

into the water tank.

Put the water tank back into the

appliance.

Clean the pre-filter

and descale the

humidification filter

Filter alert light

status

Follow this

Filter light /

goes on

Clean the

pre-filter and

descale the

humidification

filter

Note

•Only the pre-filter and humidification

filter are washable. Filter 2 is not

washable.

•Filter light / goes on approximately

once every month.

1 Wash the pre-filter under a running

tap. If the pre-filter is very dirty, use a

soft brush to brush away the dust.

2 Air dry the pre-filter.

Note

•Make sure that the pre-filter is

completely dry. If it is still wet, bacteria

may multiply in it and shorten the

lifetime of the pre-filter.

3 Mix the white vinegar with an equal

amount of tap water in a container

that is large enough to soak the

humidification filter in.

Note

•White vinegar has 5% acetic acid.

•If there are white deposits (limescale) on

the filter, make sure that the side with

the white deposits is immersed in the

water.

4 Let the humidification filter soak in

the solution for one hour.

Water : Vinegar

1 : 1

1 Hour

5 Discard the water-vinegar solution.

6 Rinse the humidification filter

under the tap to rinse away vinegar

residues. During rinsing, turn the

humidification filter so that both the

front and back sides are rinsed.

7 Let excess water drip off the

humidification filter and let it air dry.

8 After the pre-filter and

humidification filter are put back

in the appliance, reset the filter

lifetime counter. (Refer to chapter

7 "Resetting the filter lifetime

counter")

English

6 Replacing the

filters

Understand the healthy

air protect lock

This appliance is equipped with the

healthy air protect lock to make sure

that the filters are in optimal condition

when the appliance is operating. When

the filter is almost full and has to be

replaced, the specific filter light ( / )

start to flash.

When you do not replace the filter in

time:

»The appliance stops operating

and it is locked.

»The specific filter light ( / )

illuminate continuously.

Note

•The appliance is locked after the filter

light has flashed for approximately 2

weeks.

Replace filter 2

Note

•Filter 2 is not

washable nor vacuum

cleanable.

Replace filter 2 when the filter light starts

flashing.

1 Remove the filters using the tag on

the filter. Take the filters by both

sides and gently deposit them into

the house hold trash bin.

AC4080 AC4081

Note

•Do not touch the pleated filter surface,

or smell the filter as it has collected

pollutants from the air.

•Wash your hands after disposing of the

used filters.

2 Remove all packaging material from

the new filter 2.

Remove all packaging material from

the new humidification filter.

3 Put the new humidification filter in

the water tank.

4 Put the water tank back into the

appliance.

5 Reset the humidification filter

lifetime counter. (Refer to chapter

7 "Resetting the filter lifetime

counter")

3 Put the new filter 2 into the

appliance.

AC4080 AC4081

4 After the pre-filter is put back in

the appliance, reset the filter 2

lifetime counter. (Refer to chapter

7 "Resetting the filter lifetime

counter")

Replace the

humidification filter

Replace the humidification filter when

filter light starts flashing.

1 Remove the used humidification

filter from the water tank.

English

7 Resetting the

filter lifetime

counter

When you replace the filters, it is

important that you also reset the filter

lifetime counter afterwards. This allows

the appliance to be in sync with the

filter lifetime.

1 Press and hold the reset button

for 3 seconds, the filter light goes

out, and the appliance resumes

work automatically in the default

settings (combi mode with AUTO as

the fan speed).

3”

8 Troubleshooting

This chapter summarizes the most common problems you could encounter with the

appliance. If you are unable to solve the problem with the information below, contact

the Consumer Care Center in your country.

Problem Possible solution

The appliance

does not work

even though it is

plugged in.

•The filter replacement light has been on continuously but

you did not replace the corresponding filter, it is now locked.

In this case, replace the filter and reset the filter time.

•The water refill light flashes. Make sure the water tank is

properly installed.

The appliance

does not work

even though it is

switched on.

The appliance is working but the buttons are not responsive.

Check is the child lock is on (for AC4081 only).

The water tank

leaks.

It is normal that the lid of the water tank is slightly wet when

you remove it from the appliance. However, if water drops

keep dripping from the bottom of the water tank, contact the

Consumer Care Center in your country.

There are some

white deposits on

the humidification

filter.

The white deposits are called limescale and they consist of

minerals from the water. Limescale on the humidification filter

affects the humidifying performance. Therefore you have

to descale the humidification filter when the filter light /

flashes (See the chapter "Clean the pre-filter and descale the

humidification filter").

No air comes out of

the air outlet.

Plug the appliance into the power supply and switch on.

The airflow that

comes out of

the air outlet is

significantly weaker

than before.

•The pre-filter is dirty. Clean the pre-filter (see the chapter

"Clean the pre-filter and descale the humidification filter").

•Make sure that you have removed all packaging material

from the filters.

English

Problem Possible solution

The air quality

does not improve,

even though the

appliance has been

operating for a long

time.

•One of the filters has not been placed in the appliance.

Make sure that all filters are properly installed in the

following order, starting with the innermost filter:

1) filter 2; 2) pre-filter.

•The air quality sensor is wet. The humidity level in your room

is high and causes condensation. Make sure that the air

quality sensor is clean and dry (see the chapter "Clean the

air quality sensor").

The color of the air

quality light always

stays the same.

•The air quality sensor is dirty. Clean the air quality sensor

(see the chapter "Clean the air quality sensor").

•There is not enough ventilation in the room. Open a window,

to improve the air circulation.

I do not see water

vapor coming out

of the appliance. Is

it working?

When water vapor is very fine, it is invisible. With the

NanoCloud humidification technology, the appliance produces

healthy humid air from the outlet area without formation of

water mist.

The appliance

produces a strange

smell.

The first few times you use the appliance, it may produce

a plastic smell. This is normal. However, if the appliance

produces a burnt smell, contact your Philips dealer or an

authorized Philips service centre. The appliance may also

produce an unpleasant smell when one of the filters is dirty. In

this case, clean or replace the filter concerned.

I need cleaner air

because I have an

allergy.

You can change the air quality sensor sensitivity (see the

chapter "Use the appliance, section "Set the sensitivity of the

air quality sensor") to make the appliance clean the air even

better.

The appliance is

extra loud.

•Please check if you have removed all the packaging material

from the filters.

•If the appliance is still too loud, you can change the fan

speed to a lower fan speed level.

The appliance still

indicates that I

need to replace a

filter, but I already

did.

Perhaps you did not press the reset button properly. Plug in

the appliance, press the button to switch on and press and

hold the reset button for 3 seconds.

9 Guarantee and

service

If you need information or if you have a

problem, please visit the Philips website

at www.philips.com or contact the

Philips Consumer Care Center in your

country (you find its phone number

in the worldwide guarantee leaflet). If

there is no Consumer Care Centre in

your country, go to your local Philips

dealer.

Order parts or

accessories

If you have to replace a part or want to

purchase an additional part, go to your

Philips dealer or visit www.philips.com/

support.

If you have problems obtaining the

parts, please contact the Philips

Consumer Care Center in your country

(you can find its phone number in the

worldwide guarantee leaflet).

English

Recycling

Do not throw away the product with

the normal household waste at the

end of its life, but hand it in at an

official collection point for recycling.

By doing this, you help to preserve the

environment.

Follow your country's rules for the

separate collection of electrical and

electronic products. Correct disposal

helps prevent negative consequences

for the environment and human health.

10 Notices

Electromagnetic fields

(EMF)

This Philips appliance complies with all

applicable standards and regulations

regarding exposure to electromagnetic

fields.

Compliance with EMF

Koninklijke Philips N.V. manufactures

and sells many products targeted at

consumers, which, like any electronic

apparatus, in general have the ability

to emit and receive electromagnetic

signals.

One of Philips' leading Business

Principles is to take all necessary health

and safety measures for our products,

to comply with all applicable legal

requirements and to stay well within the

EMF standards applicable at the time of

producing the products.

Philips is committed to develop,

produce and market products that

cause no adverse health effects. Philips

confirms that if its products are handled

properly for their intended use, they

are safe to use according to scientific

evidence available today.

Philips plays an active role in the

development of international EMF

and safety standards, enabling Philips

to anticipate further developments in

standardization for early integration in

its products.

中文

繁體中文

ZH-T

內容

1 重要事項 30

安全 30

2 多功能空氣清淨機與加濕器 32

3 快速入門 33

安裝濾網 33

加濕準備 34

4 使用產品 36

瞭解空氣質量指示燈 36

產品啟動和關機 36

變更工作模式 37

變更風速 38

設定定時器 39

設定濕度 39

設定兒童鎖 40

水位指示 40

5 清潔 41

清潔排程 41

清潔產品機體 41

清潔空氣質量感測器 41

清潔水箱與加濕濾網 42

清潔預過濾網並去除加濕濾網的

水垢 43

6 更換濾網 45

瞭解健康空氣智能鎖 45

更換濾網 2 45

更換加濕濾網 46

7 重設濾網使用

壽命計數器 47

8 疑難排解 48

9 保固與服務 50

訂購零件或配件 50

10 聲明 51

電磁場 (EMF) 51

回收 51

ZH-T

1 重要事項

安全

在使用本產品前，請先仔細閱讀本使用手

冊，並保留使用手冊以供日後參考。

危險

• 請勿讓水或其他液體，或是

易燃清潔劑進入產品內，以

避免電擊和/或火災。

• 請勿用水、其他液體，或是

(易燃) 清潔劑清潔產品，以

避免電擊和/或火災。

• 請勿在產品周圍噴灑殺蟲劑

或芳香劑等任何易燃物質。

• 水箱中的水不適合飲用。請

勿飲用此水，亦勿用於飼養

動物或澆灌植物。將水箱內

的水倒光時，請將水倒入排

水孔。

警告

• 在連接本產品的電源之前，

請確認本產品機體底部所標

示的電壓與本地的電源電壓

是否相同。

• 如果電源線損壞，您必須將

其交由 Philips、Philips 授

權之服務中心，或是具備相

同資格的技師進行更換，以

免發生危險。

• 當插頭、電源線或產品本身

受損時，請勿使用本產品。

• 本產品可供 8 歲以上孩童、

身體官能或心智能力退化

者，或是經驗與使用知識缺

乏者使用，但需要有人在旁

監督或適當指示如何安全使

用本產品，以及可能遭受的

危險。請勿讓孩童把玩本產

品。若無人在旁監督，不得

讓孩童清潔與維護產品。

• 請勿在出風口上方或進風口

前面放置物品，擋住進

出風口。

注意

• 本產品不可用來作為維持良

好通風的設備、替代吸塵器

清潔，或烹調時用來當作抽

油煙機使用。

• 如果供應產品電力的電源插

座接觸不良，產品插頭會發

熱。請確定將產品插頭插入

接觸良好的插座。

• 請將本產品放置在乾燥平穩

的水平面上使用。

• 產品的背面及側面須至少保

留 20 公分的間隔距離，頂

部則至少保留 30 公分的間

隔距離。

• 請勿放置任何物品於產品上

方，亦不要坐在產品上。

• 請勿將產品放置在冷氣機

正下方，以免冷凝水滴入

產品。

中文

繁體中文

ZH-T

• 請在開啟產品電源前，先確

認所有濾網皆已正確安裝。

• 僅使用本產品專用之 Philips

原廠濾網。請勿使用其他

濾網。

• 切勿使用硬物敲打產品 (特

別是進風口及出風口)。

• 請務必使用產品兩側的握柄

提起或搬動產品。

• 請勿將手指或物體插入出風

口或進風口，以避免身體受

傷或損壞產品。

• 當您使用室內噴霧式驅蟲劑

或在充滿油漬、焚香或化學

煙霧的地方時，請勿使用本

產品。

• 請勿在燃氣設備、加熱裝置

或壁爐附近使用本產品。

• 使用完畢後，或加水、清潔

或進行其他維修之前，請務

必先拔除產品的電源插頭。

• 請勿在溫差變化極大的室內

使用本產品，因為室溫差距

太大會造成本產品內部凝結

水珠。

• 為避免干擾，請將本產品遠

離使用無線電電波的電子儀

器至少 2 公尺，例如電視、

收音機，與受無線電訊號控

制的時鐘。

• 產品長時間不使用時，濾網

可能會有細菌滋生。長時間

不使用後，請檢查濾網。若

濾網很髒，請進行更換 (請

參閱「更換濾網」章節)。

• 本產品為家用產品，僅限於

在正常操作環境下使用。

• 請勿在極為潮濕或周遭溫度

很高的環境下使用本產品，

例如浴室、廁所或廚房。

• 本產品無法清除一氧化碳

(CO) 或氡氣 (Rn)。發生燃

燒意外及危險化學物品意外

時，本產品無法當作安全裝

置使用。

• 每日清潔水箱以保持潔淨。

• 水箱中只能注入冷的自來

水。請勿使用地下水或

熱水。

• 請勿將水以外的物質放入

水箱。請勿將芳香劑放入

水箱。

• 若您長時間不使用加濕功

能，請清潔水箱和加濕濾網

盤。請晾乾加濕濾網。

• 若您需要搬動產品，請先切

斷產品電源供應。接著，將

水箱內的水倒光。使用產品

兩側的握柄水平拿取產品。

• 加水及清潔時，請拔除產品

插頭。

ZH-T

2 多功能空氣清淨機與加濕器

感謝您購買本產品。歡迎來到 Philips 的世界！

請至 www.philips.com/welcome 註冊您的產品，以獲得 Philips 提供的完整支援。

Philips VitaShield IPS 技術和 NanoCloud 技術確保您「隨時享有健康好空氣」。

VitaShield IPS 技術可有效去除尺寸 >0.02 微米、包含細菌和病毒的汙染物 (超微粒、

過敏原、細菌和病毒)*。

NanoCloud 技術，利用特殊的加濕濾網，為乾燥空氣增加 H2O (水) 分子，並製造健康

加濕的空氣，而不形成水霧。此產品的加濕濾網，能阻絕水中的細菌、鈣及其他粒子。

*根據世界衛生組織 (WHO) 2008 年的微生物風險評估報告，禽流感、人類流感病毒、

退伍軍人菌、肝炎病毒與 SARS 冠狀病毒皆大於 0.02 微米。

在使用本產品前，請先仔細閱讀本使用手冊，並保留使用手冊以供日後參考。

濾網 1：預過濾網

濾網 3：加濕濾網

AC4155

水箱

濾網 2：2 合 1 HEPA 活性碳過

濾網 AC4158 (AC4080 適用)濾網 2：複合多效淨

化過濾網 AC4168

(AC4081 適用)

空氣質量

感測器

中文

繁體中文

ZH-T

3 快速入門

安裝濾網

產品隨附的濾網皆已安裝在機體內。在使

用產品前，請先拆下濾網包裝。請先取出

所有濾網，拆下濾網包裝，再將濾網裝回

產品中，如下所述：

提示

•取出或裝入濾網時，將產品靠牆擺放可獲得

較穩定的支撐。

備註

•將濾網裝入正確的位置。

•請確認是否先將濾網 2 裝入產品中，再裝

預過濾網。

•請確認有拉片的一側朝向自己。

1 將產品正面護板的底部解開，朝自己方

向輕拉正面護板的上部。

2 若要取出預過濾網，按壓兩個固定夾，

再朝自己方向拉出濾網。

3 取下產品的濾網 2。

AC4080 AC4081

4 拆下濾網 2 的包裝材料。

ZH-T

5 將拆下包裝的濾網 2 裝回產品。

AC4080 AC4081

6 將預過濾網裝回產品。

AC4080 AC4081

備註

•請確認具兩個固定夾的一側朝向自己，且預

過濾網的所有扣鉤皆已正確裝入清淨機。

7 若要重新裝入正面護板，請先將護板掛

上產品上端 (1)。然後將護板輕放入產

品機體 (2)。

加濕準備

1 取下加濕濾網的包裝材料。

2 從產品側邊拉出水箱。

3 在水箱中注入冷的自來水。

備註

•倒水進水箱時，請確認未超過 MAX 水線

指示。

中文

繁體中文

ZH-T

4 將加濕濾網放入水箱。

5 將水箱推回產品內。

ZH-T

4 使用產品

瞭解空氣質量指示燈

空氣質量指示燈顏色空氣質量等級

藍色良好

紫色普通

紅色不佳

產品電源開啟後，空氣質量指示燈會自動亮

起，並反覆顯示所有顏色。過一會後，空

氣質量指示燈會選擇符合周遭空氣質量的

相應顏色。

備註

•內建空氣質量感測器會檢測空氣質量並自動

選擇適當的空氣質量指示燈顏色。空氣乾淨

時，空氣質量指示燈會顯示藍色。空氣質

量降低時，空氣質量指示燈會變更為紫色

或紅色。

產品啟動和關機

產品預設為空氣清淨與加濕同時運作。

1 將插頭插入牆上插座。

»所有燈號亮一次後，再次熄滅。

2 按下開啟產品電源。

»淨化和加濕燈亮起。

»短暫檢測空氣質量後，空氣質量感測

器將自動選擇適當的空氣質量指示

燈顏色。

»產品進入智能模式，預設的目標濕度

為 50%

。

3 按 2 秒將產品關機。

2”

備註

•按下開啟/關閉按鈕將產品關機後，若插

頭仍插在電源插座上，產品再次啟動時，將

依前次設定繼續運作。

中文

繁體中文

ZH-T

變更工作模式

除了在空氣清淨與加濕雙重模式下運作，產

品也能在僅空氣清淨模式下運作。

1 產品開機後，按一下。

»加濕和濕度指示燈熄滅。

»加濕功能已停用。產品在僅空氣清淨

模式下運作。

2 再按一下，啟用加濕功能。

備註

•在僅空氣清淨模式下，加濕按鈕不會

反應。

•

產品無法在僅加濕模式下運作。

設定空氣質量感測器敏感度

本產品可讓您調整空氣質量感測器的敏感

度。有三種敏感度等級。

• 標準 (預設設定)

• 敏感

• 超敏感

空氣質量感測器的敏感度可依照下列方式

調整：

備註

•產品敏感度的等級設為較高時，清淨機對於

空氣中的汙染物會變得較為敏感。當清淨機

處於智能模式時，較有可能選擇高於標準模

式的風速。空氣質量感測器會依照較高敏感

度選擇適當的空氣質量指示燈顏色。

1 將本產品的插頭拔除。

2 過一會後，將插頭再次插入牆上插座。

3 同時按住風速按鈕和加濕按鈕

3 秒。

»一或多個風速指示燈閃爍，顯示空氣

質量感測器目前的敏感度等級。

3”

風速指示燈敏感度等級

+ 標準

敏感

超敏感

4 按下風速按鈕調整空氣質量感測器

的敏感度等級。

5 按住 2 秒儲存設定後將產品關機。

ZH-T

手動

您可手動選擇想要的風速。

• 按下風速按鈕一次或多次，選擇想

要的風速 ( 、或 )。

備註

•僅 AC4081 具有風速。

•在手動模式下，空氣質量達到目標 (僅空氣

清淨模式) 時，或空氣質量和濕度同時達到

目標 (雙重模式) 時，產品會以選擇的風速

持續運作。

提示

•如果空氣質量指示燈顯示藍色，表示空氣質

量良好，您可選擇較低的風速。

•另一方面，如果空氣質量指示燈顯示為紅色

或紫色，表示空氣質量不佳或普通。您可以

選擇較高風速，使空氣快速清淨。

備註

•

變更敏感度等級時，若未變更任何設定，或變

更任何設定後未按壓 2 秒，產品會恢復正常

運作模式，而不儲存任何變更。

•變更並儲存敏感度後，一旦啟動產品，將自

動以預先設定的敏感度等級開始運作。

變更風速

智能

在智能模式下，產品會依照周遭空氣質量

選擇適當的風速。

• 按下風速按鈕，選擇智能模式。

• 智能及其中一個風速指示燈 ( 、或

) 亮起。

備註

•在智能模式下，空氣質量達到目標 (僅空氣

清淨模式) 時，或空氣質量和濕度同時達到

目標 (雙重模式) 時，產品會以較低風速運

作，且風速指示燈 ( 、或 ) 會熄滅。

中文

繁體中文

ZH-T

休眠模式

休眠模式下，產品運作時聲音很小。

• 按下風速按鈕，選擇休眠模式。

»休眠模式指示燈亮起。

若要變更風速，請按下風速按鈕。

備註

•產品切換成休眠模式時，指示燈會在 1 分鐘

後熄滅，而產品持續運作。

設定定時器

您可以使用定時功能，讓產品在設定的小

時數內運作。設定時間結束後，產品將自

動關機。

1 按下定時按鈕啟用定時功能。

»定時指示燈 ( 、或 ) 亮起。

2 重複按定時按鈕，選擇想讓產品運

作的小時數。相對應的定時指示燈會

亮起。

若要停用定時功能，重複按定時按鈕，

直到定時指示燈 ( 、或 ) 熄滅。

設定濕度

備註

•要使用加濕功能時，請確認水箱已裝水

(請參閱「開始使用」一章，「加濕準備」

一節)。

• 按下加濕按鈕一次或多次，將想要

的空氣濕度設定為 40%、50% 或

60%。

»相應的濕度指示燈 (40%

、

50% 或

60%) 開始閃爍。

»產品達到目標濕度時，濕度指示燈將

持續點亮。

備註

•若想短時間內增加濕度，可選擇較高風速。

ZH-T

設定兒童鎖

備註

•兒童鎖僅適用於 AC4081。

• 同時按住風速按鈕和定時按鈕

3 秒，啟用兒童鎖。

3”

»兒童鎖啟用時，所有按鈕都不會有

反應。

• 再次同時按住風速按鈕和定時按鈕

3 秒，停用兒童鎖。

3”

備註

•兒童鎖啟用時，按任何按鈕後，產品不會有

任何反應。

水位指示

水箱的水位指示可從產品側邊的水位窗查

看。水箱水量不足時，閃爍，表示必須

向水箱加水。

備註

•水箱中沒水時，加水指示燈持續點亮，

加濕指示燈也會閃爍，提醒使用者加濕功能

無法使用。水箱加水後，加濕功能即恢復。

•在僅空氣清淨模式下，加水指示燈不會

亮起。

中文

繁體中文

ZH-T

5 清潔

備註

•進行清潔前，請務必先拔離電源插頭。

•切勿讓產品浸入水或其他液體中。

•切勿使用漂白劑或酒精等具磨蝕性、刺激性

或易燃性的洗劑清潔產品的任何部分。

•僅預過濾網和加濕濾網可以清洗。空氣清淨

機濾網不得清洗，亦不得使用吸塵器清潔。

清潔排程

頻率清潔方法

必要時用柔軟的乾布擦拭產品

表面。

每週沖洗加濕濾網。

沖洗水箱。

濾網更換指

示燈 / 亮

起時

清潔預過濾網。

以醋水混和液去除加濕濾

網的水垢。

每兩個月以乾棉棒清潔空氣質量感

測器和空氣濕度感測器。

清潔產品機體

定期清潔產品的內部與外殼，可避免累積

灰塵。

1 請使用柔軟的乾布擦除產品機體的

灰塵。

2 請使用柔軟的乾布清潔進風口及出

風口。

清潔空氣質量感測器

每兩個月清潔空氣質量感測器，使產品發

揮最佳功效。如果在佈滿灰塵的環境中使

用產品，就要更常進行清潔。

備註

•當室內濕度很高時，空氣質量感測器上可能

會有水滴凝結。因此，即使空氣質量良好，

空氣質量指示燈仍可能顯示空氣質量不良。

在此情況下，您必須清潔空氣質量感測器，

或使用手動風速設定。

1 使用軟刷清潔空氣質量感測器的進風口

和出風口。

2 取下空氣質量感測器的蓋子。

ZH-T

3 請使用略濕的棉棒，清潔感測器、覆有

灰塵的進風口和出風口。

4 使用乾棉棒擦乾。

5 將感測器的蓋子重新裝回。

清潔水箱與加濕濾網

每週清潔水箱與加濕濾網以保持衛生。

1 從產品側邊拉出水箱。

2 從水箱取下加濕濾網。

3 以流動的自來水沖洗加濕濾網。

備註

•請勿刷洗加濕濾網，或將其置於陽光

直射處。

4 解開水箱蓋邊緣的鎖，並從水箱取下。

5 以流動的自來水沖洗水箱。

備註

•視需要使用中性清潔劑來清潔水箱。在此情

況下，請徹底沖洗水箱。

中文

繁體中文

ZH-T

6 用柔軟的乾布擦乾水箱和水箱蓋。

7 將蓋子裝回水箱，將鎖鎖緊。

8 將加濕濾網放回水箱。

將水箱放回產品中。

清潔預過濾網並去除加濕濾

網的水垢

濾網警示燈狀態

遵循此程序

濾網指示燈 /

亮起

清潔預過濾網並去

除加濕濾網的水垢

備註

•

僅預過濾網和加濕濾網可以清洗。濾網 2 不

得清洗。

•濾網指示燈 / 大約每個月會亮一次。

1 以流動的自來水清洗預過濾網。若預過

濾網很髒，請使用軟刷來清除灰塵。

2 讓預過濾網自然風乾。

備註

•請確認預過濾網已全乾。如果預過濾網仍

濕，細菌可能會在其中滋生，造成其使用壽

命縮短。

3 在容器內將白醋與等量自來水混合，容

器要大到足以浸泡加濕濾網。

ZH-T

備註

•白醋含 5% 醋酸。

•濾網上如有白色沉積物 (水垢)，請確認有白

色沉積物的該測浸泡在水中。

4 讓加濕濾網在此溶液中浸一小時。

水 : 醋

1 : 1

1 小時

5 將水醋混合溶液丟棄。

6 以自來水沖洗加濕濾網，沖掉殘留的醋

液。沖洗時，轉動加濕濾網，讓濾網前

後側都能沖洗到。

7 讓加濕濾網上多餘的水份流下並讓其自

然風乾。

8 預過濾網和加濕濾網裝回產品後，重設

濾網使用壽命計數器。(請參閱 7 章

「重設濾網使用壽命計數器」)

中文

繁體中文

ZH-T

6 更換濾網

瞭解健康空氣智能鎖

本產品配備健康空氣智能鎖功能，可確保

濾網在產品運作時處於最佳狀態。當濾網

即將卡滿髒污而必須更換時，專屬濾網指

示燈 ( / ) 將開始閃爍。

若未即時更換濾網：

»產品將停止運作並上鎖。

»專屬濾網指示燈 ( / ) 將持續點

亮。

備註

•濾網指示燈閃爍約 2 週後產品即上鎖。

更換濾網 2

備註

•濾網 2 不得

清洗，亦不得使用吸塵器清潔。

濾網指示燈開始閃爍時，請更換濾網 2。

1 使用濾網上的拉片取下濾網。從兩側握

住濾網，輕輕丟棄至家用垃圾桶。

AC4080 AC4081

備註

•請勿碰觸有皺摺的濾網表面或嗅聞濾網，

因為它收集了空氣中的污染物。

•丟棄舊濾網後請洗手。

2 拆下新濾網 2 的所有包裝材料。

3 將新濾網 2 裝至產品。

AC4080 AC4081

4 預過濾網裝回產品後，重設濾網 2 使

用壽命計數器。(請參閱第 7 章「重設

濾網使用壽命計數器」)

ZH-T

更換加濕濾網

濾網指示燈開始閃爍時，請更換

加濕濾網。

1 從水箱取下舊的加濕濾網。

拆下新加濕濾網的所有包裝材料。

3 將新的加濕濾網裝回水箱。

4 將水箱放回產品中。

5 重設加濕濾網使用壽命計數器。

(請參閱第 7 章「重設濾網使用壽命

計數器」)

中文

繁體中文

ZH-T

7 重設濾網使用

壽命計數器

更換濾網時，請務必隨後重設濾網使用壽

命計數器。如此可讓產品與濾網使用壽命

的時間一致。

1 按住重設按鈕 3 秒，濾網指示燈熄

滅，產品自動以預設方式恢復運作 (雙

重模式，風速為智能)。

3”

ZH-T

8 疑難排解

本單元概述您使用本產品時可能遇到的最常見問題。如果您無法利用以下資訊解決您遇到的問

題，請聯絡您所在國家/地區的客戶服務中心。

問題可能的解決方法

產品即使已插電也無

法運作。

•濾網更換指示燈持續點亮，但由於未更換相應濾網，產品已上

鎖。在此情況下，請更換濾網並重設濾網時間。

•加水指示燈閃爍。請確認水箱正確安裝。

即使產品電源已開

啟，仍無法運作。

產品運作中，但按鈕沒反應。檢查兒童鎖是否鎖上 (僅適用於

AC4081)。

水箱漏水。從產品取下水箱蓋時，水箱蓋微濕是正常現象。然而，如果水滴持

續從水箱底滴出，請聯絡所在國家/地區的客戶服務中心。

加濕濾網上有白色沉

積物。

白色沉積物稱為水垢，由水中礦物質所組成。加濕濾網上的水垢

會影響加濕性能。因此，濾網指示燈 / 閃爍時，必須去除加濕

濾網的水垢 (請參閱「清潔預過濾網並去除加濕濾網的水垢」

章節)。

出風口沒有空氣

流出。

請將產品插頭接上電源，然後開啟電源。

出風口流出的風速比

之前慢很多。

•預過濾網髒污。清潔預過濾網 (請參閱「清潔預過濾網並去除加濕

濾網水垢」章節)。

•請確認已拆下濾網的所有包裝材料。

即使產品已經長時間

運作，空氣質量仍未

獲得改善。

•其中一個濾網尚未裝入產品中。請確認所有濾網皆已按照下列順

序正確安裝，由內至外順序為：1) 濾網 2；2) 預過濾網。

•空氣質量感測器潮濕。室內的濕度很高，造成水珠凝結。請確認

空氣質量感測器乾淨且乾燥 (請參閱「清潔空氣質量感測器」

章節)。

空氣質量指示燈的顏

色一直維持不變。

•空氣質量感測器髒污。清潔空氣質量感測器 (請參閱「清潔空氣質

量感測器」章節)。

•室內空氣不夠流通。請開窗，促進空氣流通。

我沒看到產品飄出

水氣。產品有在運

作嗎？

水氣很細時，是看不見的。本產品採用 NanoCloud 加濕技術，從

出風口區製造出健康加濕的空氣而不形成水霧。

中文

繁體中文

ZH-T

問題可能的解決方法

使用產品時發出

異味。

使用本產品的前幾分鐘，可能會產生塑膠味。此為正常現象。

然而，產品如果產生燒焦味，請聯絡 Philips 經銷商或經授權的

Philips 服務中心。其中一個濾網髒污時，產品亦可能產生難聞氣

味。在此情況下，請清潔或更換該濾網。

因為本身過敏，我需

要更潔淨的空氣。

如要讓產品更徹底清淨空氣，您可以變更空氣質量感測器敏感度

(請參閱「使用本產品」一章，「設定空氣質量感測器敏感度」

一節)。

產品噪音太大。

•請檢查是否已拆下濾網的所有包裝材料。

•如果產品噪音仍然很大，可將風速變更為較低的風速等級。

產品不斷指示需更換

濾網，但濾網已經更

換了。

您可能未確實按下重設按鈕。為產品插上電源，按下按鈕啟

動，按住重設按鈕 3 秒。

ZH-T

9 保固與服務

若您需要相關資訊或有任何問題，請造訪

Philips 網站 www.philips.com，或聯絡您

所在國家/地區的 Philips 客戶服務中心 (您

可在全球保證書上找到電話號碼)。若您所

在國家/地區沒有客戶服務中心，請洽地的

Philips 經銷商。

訂購零件或配件

如果您必須更換零件或想購買其他零件，

請聯絡您的 Philips 經銷商，或造訪

www.philips.com/support。

如果您有取得零件方面的問題，請聯絡您所

在國家/地區的 Philips 客戶服務中心 (您可

在全球保證書上找到電話號碼)。

中文

繁體中文

ZH-T

10 聲明

電磁場 (EMF)

本 Philips 產品符合所有電磁場暴露的相關

適用標準和法規。

符合 EMF 標準

Koninklijke Philips N.V. 製造銷售多項消費

性產品，這些產品就如同其他電器，通常

能收發電磁訊號。

Philips 的一大企業原則，就是針對自身的

產品進行必要的健康與安全檢測，以符合

所有適用的法律規定，以及在產品生產期

間符合適用的 EMF 標準。

Philips 致力於開發、生產及銷售不危害健

康的產品。Philips 保證，只要依照正確

用途並妥善使用，根據現有的科學研究資

料，使用本公司產品並無安全顧慮。

Philips 積極參與國際 EMF 與安全標準的

開發，因此得以掌握標準化的發展，及早

將標準化與自身的產品整合。

回收

請勿在本產品使用壽命結束後當作一般家

庭垃圾廢棄，應交給官方回收站作循環再

用。這樣做有助保護環境。

請遵守您的國家/地區回收電器和電子產品

的法則。正確處理廢棄產品有助避免對環

境和人體造成負面影響。

單元 Unit 鉛

(Pb)

Lead

汞

(Hg)

Mercury Cadmium Hexavalent

chromium

Polybrominated

biphenyls

Polybrominated

diphenyl ethers

鎘

(Cd)

六價鉻

(Cr+6)

多溴聯苯

(PBB)

多溴二苯醚

(PBDE)

限用物質及其化學符號

Restricted substances and its chemical symbols

電源線組

塑膠外殼

電源板組件

電動機

主電路板組件

○

○○

○

○ ○ ○ ○ ○

設備名稱：飛利浦空氣清淨機，型號（型式）：AC4080/80，AC4081/80

Equipment name Type designation (Type)

備考1：“超出0.1 wt %”及“超出0.01 wt %”係指限用物質之百分比含量超出百分比

含量基準值。

備考2：“○”係指該項限用物質之百分比含量未超出百分比含量基準值。

備考3：“－”係指該項限用物質為排除項目。

Note 1 : “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the

restricted substance exceeds the reference percentage value of presence condition.

Note 2 : “○” indicates that the percentage content of the restricted substance does not exceed the

percentage of reference value of presence.

Note 3 : The “－” indicates that the restricted substance corresponds to the exemption.

4241 210 79434