Philips GC9920 User Manual
Displayed below is the user manual for GC9920 by Philips which is a product in the Steam Ironing Stations category. This manual has pages.
Related Manuals
Quick start guide
Ironing
1
Steaming
Refreshing
Automatic
Calc-Cleaning
GC9920
Storage
2
3
4
5
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
Exploded view
A Hanger hook
B Refreshing button
C Air vents
D Air vent slide
E NeverBurn ironing board cover
F Fan
G Board handle
H Board tilting button
I Height adjustment lever
J Locking strap
K Iron compartment
L Iron
M Mains plug
N Rinse tray
O Water tank
P Water tank release button
Q Power-on light
R Steamer compartment
S Steamera
General description
Ironing
J
H
I
D
T
M
U
V
T Steam activator
U Iron power-on button with light
V Blowing/suction button
D Air vent slide
I Height adjustment lever
H Board tilting button
J Locking strap
M Mains plug
Put the mains plug M in an earthed
wall socket. The power-on light goes
on.
Fill the water tank.
Undo the locking strap J and unfold
the ironing board to vertical position.
Set both air vent slides D to the
ironing position.
Push the board tilting button H and
tilt the board to horizontal position.
Set the ironing board to the
appropriate height by means of the
height adjustment lever I.
Take the iron out of the iron
compartment, either from the left or
right side.
Switch the iron on by pressing the iron
power-on button U. The power-on
light goes on.
After approx. 2 minutes the iron
is ready for use.
If you want to iron with steam, set the
temperature dial of the iron to 2 or
higher and press the steam activator T.
Never direct the steam
at people.
If you want to iron in the blowing
mode, press the rounded side of the
blowing/suction button.
If you want to iron in the suction
mode, press the hollow side of the
blowing/suction button.
You can safely put down the hot iron
on the board cover during ironing.
You can store the hot iron in the
heat-resistant storage compartment
immediately after you have switched
the iron off.
1
2
3
5
4
6
7
8
E Ironing tips and tricks
To iron shirts, use the wide end of the board to save time
and energy.
To avoid shine and seam imprints, use the blowing mode.
To hold the garment at on the board, use the suction mode.
•
•
•
1
M
D
A
T
H
I
J
U
V
A Hanger hook
D Air vent slide
U Steamer power-on button with light
V Blowing/suction button
T Steam activator
H Board tilting button
I Height adjustment lever
J Locking strap
M Mains plug
Steaming
Put the mains plug M in an earthed
wall socket. The power-on light goes on.
Fill the water tank.
Undo the locking strap J and unfold
the ironing board to vertical position.
Set both air vent slides D to
the ironing position.
Take the steamer out of the steamer
compartment.
Switch the steamer on by pressing
the steamer power-on button U.
The power-on light goes on.
After approx. 2 minutes the
steamer is ready for use.
Press the steam activator T.
Never direct the steam
at people.
If you want to steam in the blowing
mode, press the rounded side of the
blowing/suction button.
If you want to steam in the suction
mode, press the hollow side of the
blowing/suction button.
You can easily hang the steamer on
the board handle G when necessary.
You can store the hot steamer in the
heat-resistant storage compartment
immediately after you have switched
the steamer off.
6
4
5
3
2
1
E Steaming tips and tricks
The steamer is perfect for all delicate fabrics, such as silk,
wool and cashmere.
To steam a jacket, put it directly on the board. To steam a
blouse or a dress, use the hanger hook A.
•
•
2
7
B
C
D
H
I
J
M
B Refreshing button
C Air vent
D Air vent slide
H Board tilting button
I Height adjustment lever
J Locking strap
M Mains plug
Refreshing
Put the mains plug M in an earthed
wall socket. The power-on light goes on.
Undo the locking strap J and unfold
the ironing board to vertical position.
Set both air vent slides D the
refreshing position.
Press the refreshing button B on the
back of the ironing board.
The appliance starts refreshing your
garment.
This process takes 10 minutes and
automatically stops.
1 2
N
Q
This appliance is equipped with an automatic Calc-Cleaning system. When the power-on light Q blinks,
the Calc-Cleaning system is active. Wait 3 minutes for the appliance to complete the Calc-Cleaning
process. During this process you cannot use the appliance.
When the power-on light Q stops blinking and the rinse tray light starts blinking, empty the rinse tray
N and reinsert it. The Calc-Cleaning process is now finished and you can start using the appliance.
4Automatic Calc-Cleaning
1
E Refreshing tips and tricks
Perfect to remove food or cigarette smoke smells from
jackets, coats and sweaters.
Combine the refreshing mode with the steaming mode to
refresh garments and remove creases at the same time.
•
•
Storage
Fold the ironing board to the storage
position and lock the board with the
locking strap.
To store the cord, briefly pull it
towards you and then let it go.
The cord will be wound up
automatically.
You can now easily move the
appliance by pulling it along by the
board handle.
1
2
3
5
3
Frequently asked questions
This chapter lists the questions most frequently asked about the appliance. If you can’t find the answer to your question, contact the
Customer Care Centre in your country.
Question
Why doesn’t the appliance work?
Why does the iron/steamer remain
cold?
Why does the iron/steamer switch
off?
Why does the refreshing mode switch
off?
Why doesn’t the iron/steamer
produce any steam?
Why does the appliance produce
noise?
Why is the airflow insufficient?
Why are there water droplets/wet
spots on the ironing board?
Why do water droplets come out
of the iron/steamer?
Why does the light on the
iron/steamer blink?
Why does the water tank light
blink?
Why does the power-on light on
the appliance blink?
Why does the rinse tray light blink
and the appliance beep?
Why does smoke come out of the
iron/steamer?
What is the purpose of the blowing
mode?
What is the purpose of the suction
mode?
Answer
There may be a connection problem. Check the mains cord, the plug and the wall socket.
The iron/steamer may not be switched on. Take the iron/steamer out of the storage compartment and press
the on/off button on the iron/steamer once.
The automatic Calc-Cleaning process may be in progress or the rinse tray is full. Wait until the Calc-Cleaning
process is finished. During Calc-Cleaning, the power-on light blinks for 3 minutes. After Calc-Cleaning, the rinse
tray light blinks and you will hear a few beeps. Empty the rinse tray and put it back in place. Then switch on the
iron/steamer.
The auto-shut-off function may have been activated. The appliance is switched off automatically when the
steam activator on the iron/steamer has not been used for 5 minutes. Deactivate the auto-shut-off function
by pressing the on/off button on the iron/steamer once. Wait until the light on the iron/steamer stops blinking
and starts burning continuously.
The refreshing mode runs for 10 minutes and then switches off automatically. You can switch the refreshing
mode back on by pressing the refreshing button.
There may not be enough water in the water tank or the water tank is not properly placed in the water tank
compartment. Fill the water tank and put it back into the water tank compartment properly.
The appliance may not be hot enough for steaming. Heating up takes two minutes. Wait until the light on the
iron/steamer stops blinking and starts burning continuously. Then press the steam activator to start steaming.
You may not have pressed the steam activator. Press the steam activator on the handle of the iron/steamer to
start steaming.
When you hear an intermittent noise, water is intermittently pumped from the water tank into the boiler.
If the noise continues for a long time or if it becomes very loud, first check whether the water tank is properly
inserted into the appliance. If this is the case but the noise still persists, switch off the appliance and contact
the Philips Customer Care Centre or your Philips dealer.
The appliance is equipped with an illuminiated fan that runs continuously during use. This fan optimises the
performance of the appliance and cannot be switched off.
The air vent slides are probably in the wrong position. In ironing and steaming mode, the air vents must be
closed by setting both air vent slides to the ironing position. It is normal for some air to come out of the vents
after they have been closed; this does not affect the performance of the appliance. In refreshing mode, the air
vents must be opened by setting both air vent slides to the refreshing position.
If the ironing board is used for a prolonged period, too much steam condenses inside the ironing board,
causing wet spots on the cover. After use, leave the ironing board folded out for some time to let it dry.
Alternatively, press the refreshing button and let the fan operate until the appliance switches off automatically
after 10 minutes. Then unplug and store the appliance.
Water collects inside the hose of the iron/steamer. This means that water droplets will come out of the
iron/steamer during the first few seconds of steaming at the start of an ironing/steaming session and after an
interruption during the session.
The temperature setting of the iron is too low. Set the temperature dial of the iron to two dots or higher.
The iron/steamer is not yet ready for use; the boiler is still heating up. Wait for 2 minutes until the light stops
blinking and starts burning continuously. Then press the steam activator on the iron/steamer to start steaming.
The water tank is empty or not properly placed. In this case, the water tank light blinks, the appliance beeps
and the iron/steamer does not produce steam when the steam activator is pressed. Fill the water tank and
insert the water tank properly by pushing it firmly into the water tank compartment.
The power-on light blinks during the Calc-Cleaning process, which is performed automatically once every
few ironing sessions. The Calc-Cleaning process is designed to keep the appliance scale-free. Wait until the
Calc-Cleaning process is completed (when the rinse tray light starts blinking and the appliance beeps), empty
the rinse tray and reinsert it. Then switch on the iron/steamer.
When the Calc-Cleaning process is finished, the rinse tray light starts blinking and the appliance beeps.
Empty the rinse tray and reinsert it before switching on the iron/steamer.
Some smoke may come out of the iron/steamer when you use the appliance for the first time because some
parts of the appliance have been lightly greased. This smoke is normal and will cease after a short while.
When you use the blowing mode, the garment lies on a cushion of air. This prevents shine and seam imprints.
When you use the suction mode, the garment is held flat and neat on the ironing board.
This ensures crease-free ironing.
Important
Read this user manual carefully before you use the appliance and
save it for future reference.
Check if the voltage indicated on the type plate corresponds to
the local mains voltage before you connect the appliance.
Only connect the appliance to an earthed wall socket.
Do not use the appliance if the plug, the cord, the supply hoses
or the appliance itself shows visible damage, or if the appliance
has been dropped or is leaking.
Check the cord and supply hoses regularly for possible damage.
If the mains cord or the supply hoses of this appliance are
damaged, they must be replaced by Philips, a service centre
authorised by Philips or similarly qualied persons in order to
avoid a hazard.
Never leave the appliance unattended when it is connected to
the mains.
Never immerse the iron, the steamer or the appliance in water.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
Never remove the ironing board cover while ironing or
immediately after use. Always let the appliance cool down
sufciently before you remove the cover.
The soleplate of the iron can become extremely hot and may
cause burns if touched.
Never allow the mains cord and supply hoses to come into
contact with the hot soleplate of the iron.
When you have nished ironing/steaming, when you clean the
appliance and also when you leave the appliance even for a
short while, remove the mains plug from the wall socket.
Do not move the appliance when it is in use.
Do not use the appliance with very wet fabrics.
Always place and use the appliance on a stable, level and
horizontal surface.
Do not put a cloth, sheet or any other cover over the appliance
immediately after use.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
If steam escapes from the rinse tray during use, switch the
appliance off and contact a service centre authorised by Philips.
Always transport the appliance in storage position with the
ironing board folded and the locking strap properly secured.
This appliance is intended for indoor household use only. Do
not expose the appliance to atmospheric agents (e.g. rain, sun,
cold).
Type of water to be used
• Do not put perfume, vinegar, starch, descaling agents, ironing
aids or other chemicals in the water tank.
• You can use normal tap water. If the tap water in your area
is very hard, we advise you to mix it with an equal amount of
distilled water, or to use distilled water only.
Environment
Do not throw the appliance away with the
normal household waste at the end of its life,
but hand it in at an official collection point for
recycling. By doing this you will help to
preserve the environment.
Electromagnetic fields (EMF)
This Philips appliance complies with all standards regarding
electromagnetic fields (EMF). If handled properly and in
accordance with the instructions in this instruction manual, the
appliance is safe to use according to scientific evidence available
today.
Guarantee & service
If you need information or if you have a problem, please visit
the Philips website at www.philips.com or contact the Philips
Customer Care Centre in your country (you will find its
phone number in the worldwide guarantee leaflet). If there is
no Customer Care Centre in your country, turn to your local
Philips dealer or contact the Service Department of Philips
Domestic Appliances and Personal Care BV.
-
-
-
www.philips.com 4239.000.6135.4
u