Overview
1 General Safety Information
2 Overview
3 Initial Operation
4 Connect to the Playback Device
5 Memory
- Inserting a Memory Card
- Connecting USB Storage Medium
6 Network
7 Bluetooth
8 Media Playback
9 Digital TV Playback (Depending on model)
10 Android
11 Settings
- Overview of the Menu Functions
12 Service
13 Appendix
- Technical Data
- Accessories

Philips HDP1690TV User Manual

Displayed below is the user manual for HDP1690TV by Philips which is a product in the Data Projectors category. This manual has pages.

Related Manuals

Philips MC-I250/22 Manual

Philips HQ8890 Manual

Philips HQ6849 Manual

Philips HQ6415 Manual

Philips MP3 Micro HiFi-System MCM250 Manual

Philips AJ3600/37 Manual

Philips HQ6707/16 Manual

Philips HQ8850 Manual

www.philips.com/welcome

Screeneo

HDP1650TV

HDP1690TV

EN User Manual

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 1 Jeudi, 12. février 2015 10:33 10

2Philips · HDP16x0TV

Table on Contents

Overview ...................................................3

Dear Customer ....................................................................3

About this User Manual ......................................................3

What's in the Box ................................................................3

Product Highlights ...............................................................3

1 General Safety Information ................4

Setting up the Device ..........................................................4

Automatic device temperature control ..........................4

Repairs .................................................................................... 4

Power Supply ........................................................................5

Wireless Network (WLAN) .............................................5

3D glasses use .......................................................................5

Dolby Digital .........................................................................5

2 Overview ...............................................6

Front View .............................................................................6

Rear View ..............................................................................6

Remote Control ...................................................................7

Browsing the user interface ...............................................8

Overview of the Menu Functions .....................................9

Symbols in the Statusbar ....................................................9

3 Initial Operation ................................10

Setting up the Device ........................................................10

Connect Power Supply .....................................................10

Installing or Changing the batteries of the

IR Remote Control ............................................................10

Using the Remote Control ..............................................11

Installing or Changing the batteries of the

RF Remote Control ...........................................................11

3D glasses ............................................................................14

Initial Installation .................................................................15

4 Connect to the Playback Device ......16

Connecting to Devices with HDMI Output ................16

Connecting to a Computer (VGA) ................................16

Connecting Using an Audio/Video (CVBS)

Adapter Cable .....................................................................17

Connecting to a home cinema amplifier .......................17

Connecting to a Hi-Fi unit ...............................................17

Connecting the headphones ............................................18

WiFiDisplay (Miracast) ......................................................18

Directly Connecting Projector to Computer

using WLAN (WiFi Streaming) .......................................18

ScreeneoWLink software ................................................18

5 Memory ...............................................21

Inserting a Memory Card .................................................21

Connecting USB Storage Medium ..................................21

6 Network ..............................................22

LAN Network ....................................................................22

Wireless Network (WLAN) ...........................................22

Switching Wireless Networking (WLAN) on/off .......23

Setting up a Wireless Network (WLAN) ....................23

Setting up a Wireless Network (WLAN)

using the Wizard ................................................................ 23

Wifi Hotspot ....................................................................... 24

Digital Living Network Alliance (DLNA) ..................... 25

7 Bluetooth ........................................... 26

Activating the Bluetooth connection ............................ 26

Setting up Bluetooth parameters ................................... 26

Bluetooth speaker ............................................................. 26

8 Media Playback .................................. 28

Navigating in the media Playback ...................................28

Video playback .................................................................... 29

Photo Playback ...................................................................29

Music Playback .................................................................... 31

Managing Files .....................................................................32

9 Digital TV Playback

(Depending on model) ........................... 33

Connecting the Aerial ...................................................... 33

First Playback ...................................................................... 33

Television ............................................................................. 34

Modifying the DVB-T settings ......................................... 34

10 Android ............................................... 35

Starting Android Apps ......................................................35

Exiting Android .................................................................. 35

Installing Android-Apps ....................................................35

11 Settings ............................................... 36

Overview of the Menu Functions .................................. 36

12 Service ................................................ 38

Cleaning ............................................................................... 38

Device Overheated ........................................................... 38

Update Firmware with Memory Card ..........................38

Troubleshooting ................................................................. 39

13 Appendix ............................................ 41

Technical Data .................................................................... 41

Accessories ......................................................................... 41

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 2 Jeudi, 12. février 2015 10:33 10

Overview

Dear Customer

Thank you for purchasing our projector.

We hope you enjoy your device and its many functions!

About this User Manual

With the installation guide on the following pages, you

can start using your device quickly and easily. Detailed

descriptions can be found in the following sections of

this user manual.

Read the entire user manual carefully. Follow all safety

instructions in order to ensure proper operation of

your device. The manufacturer accepts no liability if

these instructions are not followed.

This user manual describes several versions of the prod-

uct.

An infrared remote control (IR) is provided with the

HDP1650TV model.

A radio frequency remote control (RF) is provided with

the HDP1690TV model.

Symbols Used

What's in the Box

1 – Projector

2 – Remote Control (with 2AAA battery)

3 – A/C power cable

4 – USB - Mini USB Cable for charging 3D glasses

5 – 3D Glasses with a quick start guide, a warning label

and a protection bag (depending on model)

6 – Quick Start Guide

7 – Warranty Guide

8 – Bag

Product Highlights

Connecting to devices with HDMI output

With a HDMI cable you can connect the projector to a

computer or laptop (see Connect to the Playback

Device, page 16).

WiFiDisplay (Miracast)

With the Miracast™ solution you can display video

between Wi-Fi devices, without cables or a network

connection. You can do things like view pictures or vid-

eos from a smartphone or laptop on your projector.

Notice

Troubleshooting

This symbol designates tips that will help you

to use your device more effectively and easily.

CAUTION!

Damage to the Device or Loss of Data!

This symbol gives warning of damage to the

device and possible loss of data. This damage

can result from improper handling.

DANGER!

Danger to Persons!

This symbol gives warning of danger to per-

sons. Physical injury or damage can result

from improper handling.

78 9

45 6

12 3

TUV WXYZPQRS

GHI JKL MNO

. @ ABC DEF

SUBTITLE TEXT

CH - CH +

EXIT

OPTIONS

LIST INFO

SOURCE

FORMAT

SMART

GUIDE 3D

AMBILIGHT

PHILIPS

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 3 Jeudi, 12. février 2015 10:33 10

4Philips · HDP16x0TV

1 General Safety Information

Do not make any changes or settings that are not

described in this user manual. Physical injury or damage

to the device or loss of data can result from improper

handling. Take note of all warning and safety notes indi-

cated.

Setting up the Device

The unit is for indoor use only. The device should be

placed securely on a stable, flat surface. Position all

cables in such a way that no one will stumble on them,

thus avoiding possible injuries to persons or damage to

the device itself.

Do not plug in the device in moist rooms. Never touch

the mains cable or the mains connection with wet

hands.

The device must have sufficient ventilation and may not

be covered. Do not put your device in closed cabinets

or boxes.

Do not place the machine on soft surfaces such as table-

cloths or carpets and do not cover the ventilation slits.

Otherwise the device could overheat or catch fire.

Protect the device against direct sunlight, heat, large

temperature fluctuations and moisture. Do not place

the device in the vicinity of heaters or air conditioners.

Observe the information on temperature and humidity

in the technical data.

Do not allow liquids to enter into the device. Switch off

the device and disconnect it from the mains supply if liq-

uids or foreign substances end up inside the device.

Have the unit inspected by a technical service depart-

ment.

Always handle the unit with care. Avoid touching the

lens. Never place heavy or sharp objects on the projec-

tor or the power cable.

If the projector gets too hot or emits smoke, shut it

down immediately and unplug the power cable. Arrange

for your device to be investigated by a technical service

centre. To prevent the spread of fire, open flames

should be kept away from the device.

Under the following conditions, a layer of moisture can

appear inside the device which can lead to malfunctions:

• if the device is moved from a cold to a warm

area;

• after a cold room is heated;

• when this device is placed in a damp room.

Proceed as follows to avoid any moisture build-up:

1Seal this device in a plastic bag before moving it to

another room, in order for it to adapt to room con-

ditions.

2Wait one to two hours before you take the device

out of the plastic bag.

The device should not be used in a very dusty environ-

ment. Dust particles and other foreign objects may

damage the unit.

Do not expose the device to extreme vibrations. It may

damage the internal components.

Do not allow children to handle the device without

supervision. The packing materials should be kept out of

the hands of children.

Automatic device

temperature control

This device include an automatic thermal management

controller. If the internal temperature gets too hot, the

Fan speed will automatically increase (noise increase), if

the temperature still continue to growth, the brightness

of your product will decrease and in worst case the cur-

rent symbol will appear.

The product will automatically switch off the display

after displaying this message during 5s.

This kind of behaviour should not arrive except if the

outside temperature is very high (>35°C). In such case

return the product to the manufacturer would be rec-

ommended.

Repairs

Do not repair the device yourself. Improper mainte-

nance can result in injuries or damage to the device.

Your device must be repaired by an authorised service

centre.

Find details of authorised service centres on the war-

ranty card.

Do not remove the type label from your device; this

would void the warranty.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 4 Jeudi, 12. février 2015 10:33 10

General Safety Information 5

Power Supply

Before turning on your device, check that the outlet

that you are going to plug it into conforms to the indi-

cations shown on the information plate (voltage, cur-

rent, power network frequency) located on your

device. This device shall be connected to a single phase

power network. The device shall not be installed on

bare ground.

Only use the power cable that is supplied with your

device. Your device is delivered with a grounded power

cord. It is imperative to connect a grounded connector

to a grounded outlet connected to the building earthing.

The socket outlet shall be installed near the equipment

and shall be easily accessible.

In case of failure, the power cable is the disconnect

device for this equipment. To remove all electrical

power from the equipment, disconnect the power cable

from the electrical outlet.

Turn off the device and unplug from the power outlet

before cleaning the surface. Use a soft, lint-free cloth.

Never use liquid, gaseous or easily flammable cleansers

(sprays, abrasives, polishes, alcohol). Do not allow any

moisture to reach the interior of the device.

Wireless Network (WLAN)

The functioning of security systems, medical equipment

or sensitive devices can be disrupted by the transmis-

sion power of the device. Observe any usage regula-

tions (or restrictions) in the vicinity of such equipment.

The use of this device can affect the operation of insuf-

ficiently shielded medical devices and hearing aids and

pacemakers through the release of high frequency radi-

ation. Also consult a doctor or the manufacturer of the

medical device to establish whether these are suffi-

ciently shielded from external high frequency radiation.

3D glasses use

The use of 3D glasses in home for watching TV shows:

• is contraindicated for children less than 6 years

old;

• for children from 6 years old to adulthood,

should be limited to the vision for a maximum

time equal to the duration of a film show;

• the same time limit is also recommended for

adults;

• must be restricted to watching only 3D content

• how to make a proper and regular cleaning and

disinfection in the case of any particular eventu-

alities-ocular infections, infestations of the head,

mixed use, etc. .. where disinfection of the

glasses is not possible as it may damage the func-

tionality of the 3D glasses must be communi-

cated to the consumer that in presence of these

eventualities-infections is contraindicated the

use of 3D glasses for the person concerned until

the disappearance of the above circumstances;

• 3D glasses must be kept out of children if there

is the presence of small moving parts ingestible;

• 3D glasses are to be used together with the

instruments of vision correction in case the con-

sumer is the bearer of lenses (eyeglasses or con-

tact lenses);

• You should stop watching 3D in the event of the

occurrence of eye problems or discomfort, and

in the event of a persistence of the same, consult

a doctor.

Dolby Digital

Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are trademarks of

Dolby Laboratories.

DANGER!

High Power LED

This device is equipped with high power LED

(Light Emitting Diode), which emit very bright

light. Do not look directly into the projector

lens. This could cause eye irritation or dam-

age.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 5 Jeudi, 12. février 2015 10:33 10

6Philips · HDP16x0TV

2Overview

Front View

1 Control panel for navigation and operation

u – To display the home menu

¿ – One menu step back, one directory level back

/ cancelling a function

//À/Á – Navigation keys / navigate the

menu / modify settings

 – Confirms selection

B– Long press: Power off the projector

Short press: ECO mode on / off

2 Ï – Audio output – headphone connection or con-

nection for external speakers

3  3– HDMI port for a playback device

4  – Memory card slot

5 ý – USB port for a USB storage medium or to con-

nect accessories (mouse or keyboard).

6 Focus wheel for image sharpness

Rear View

1 – Power supply outlet

2 ý – 2 USB ports for a USB storage medium

3   – Digital audio connector

4  – HDMI 1 and 2 ports for a playback device

5 Kensington Security System Connector

6 VGA – Personal Computer input

7  – LAN network connector

8  – Analog audio connectors

9 /  – A/V port for a playback device

  – Remote screen connection

 – Aerial socket for TV connection

– Lens

PHILIPS

VGA

S/PDIF

OPTICAL

AUDIO

OUT

TRIG

OUT

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 6 Jeudi, 12. février 2015 10:33 10

Overview 7

Remote Control

1 Long press: Power off the projector.

Short press: Power on the projector or ECO mode

on/off.

To power the projector on use the B key on the

control panel

2 Playback keys

– Skip backward (music only)

– To stop playback

– Skip forward (music only)

– To rewind

– To start / pause playback

– To fast-forward

3 EPG –To display the electronic program guide.

3D – To display the 3D menu.

Favorite – To display the favourite list in DVB-T

mode.

4 To display the home menu.

5 TAB key or Toggle between TV and Radio chan-

nels in DVB-T mode and browsing the Internet

without external keyboard.

6 Navigation keys

 – Confirms selection

/, À/Á – Navigation keys / navigate the

menu / modify settings.

7 EXIT – One menu step back, one directory level

back / cancelling a function.

8 PAGE/CH- PAGE/CH+ –To select the previous

channel/page or the next channel/page.

9 Color keys - On-screen options.

 Number keys and text keypad.

Short press for numbers and long press to

switch "letters"

SUB/SHIFT – To display subtitles in DVB-T mode

or shift key in input mode.

TTX/← – To display Teletext pages when available

in DVB-T mode or backspace key in input mode.

– / + – To adjust the volume level (to decrease/in-

crease and to mute the sound).

RECALL – To recall the last function or the last

channel viewed in DVB-T mode.

OPTIONS – To call the option menu.

INFO – To display program information on current

program in DVB-T mode.

MENU – To display the settings menu in DVB-T

mode.

SOURCE – To display the list of input connections.

SMART SETTINGS – To display the Smart set-

tings menu

FORMAT – To change the aspect ratio.

For radio frequency remote control (RF), a QWERTY

keyboard is available below for you to enter text easily.

SUB/SHIFT

TAB

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 7 Jeudi, 12. février 2015 10:33 10

8Philips · HDP16x0TV

Browsing the user interface

Navigation for setting menu

Infrared Remote Control (IR)

Navigation can be done by navigation keys (,,

À,Á, OK and ¿) on the control panel or the

remote control, as well as by an air mouse.

Navigation by keys:

•/ scrolls trough the menu level up and

down.

•OK/Á goes one level down, with À / ¿ one

level up.

•u goes back to the main screen.

• In the final level,  accepts a setting and goes

back to the last sub menu.

• The ¿ key aborts a setting and goes back to the

last sub menu (or exits the menu depending on

which menu)

Radio freqency Remote Control (RF)

To use the RF remote control you must connect the

supplied receiver into a USB port, refer to the chapter

“Initial Operation” page 10.

For activate the mouse touch and hold the OK button

until the pointer on the screen appears.

Select an icon by pointing with the pointer and clicking

with the OK key of the remote control.

Navigation by keys:

•/ scrolls trough the menu level up and

down.

•OK/Á goes one level down, with À / ¿ one

level up.

•u goes back to the main screen.

• In the final level,  accepts a setting and goes

back to the last sub menu.

• The ¿ key aborts a setting and goes back to the

last sub menu (or exits the menu depending on

which menu)

To use the QWERTY keyboard

•,,À and Á scrolls trough the menu.

•ENTER/Á goes one level down, with À one

level up.

•Fn to use blue characters

Navigation by (air) mouse: (like standard

mouse operation within Android)

Select an icon by pointing with the mouse pointer and

clicking with the left mouse key.

If there are more menus listed than displayed you can

scroll the list by clicking into the list and move up and

down without releasing the left mouse button.

With the right mouse key you can exit the menu and go

back to the next top level menu.

Software Keyboard

When you need to enter data, the projector displays a

virtual keyboard which allows you to enter text, num-

bers and punctuation marks, etc.

1Select the input field using the ,,À and Á

keys, then press the OK key to display the keyboard

or click in the input field using the air mouse.

2The software keyboard appears.

3Enter the text on the software keyboard.

CAUTION!

Air mouse

The air mouse is not provided with Screeneo

HDP1650TV.

Notice

To enter text, you can also use standard com-

puter keyboard or mouse. It is possible to use

wired models (USB) as well as wireless mod-

els with 2.4 GHz USB-connectors.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 8 Jeudi, 12. février 2015 10:33 10

Overview 9

Overview of the Menu

Functions

1After switching on the device the main menu

appears.

2Select the desired menu using the navigation keys

/, À/Á.

3Confirm with OK.

4By pressing the u key you will return to the main

menu.

HDMI 1, 2, & 3 – Switch to the external video input

HDMI.

TV1 – Television

DLNA – Displays the list of the devices found on the

Network.

Memory – Display the content of the internal mem-

ory and the inserted memory SD-Card (movies, pic-

tures, musics, folderview).

USB – Display the content of the connected USB

media (movies, pictures, musics, folderview).

WWW – Open an Internet web browser.

VGA – Switch to the Personal computer input.

A/V-in – Switch to the Audio Video input.

APPs – Call the android operating system.

Settings – Configure settings for the wished used of

the device.

Symbols in the Statusbar

1 – Time

2 – Date

3 – LAN status display

4 – Bluetooth status display

5 – WiFi status display

1.Depending on the device model, TV can be

replaced by BT speaker.

ab dce

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 9 Jeudi, 12. février 2015 10:33 10

10 Philips · HDP16x0TV

3 Initial Operation

Setting up the Device

Before installing your device, make sure that the

projector is turned off and the power cord is

unplugged from the power outlet.

You can position the device so that it lies flat on a table

in front of the projection surface; it is not necessary to

tilt it towards the projection surface. The device com-

pensates for the distortion from the slanted projection

(pincushion distortion).

Check that the projection surface is appropriated to the

projector. The distance between the projector and the

screen determines the actual size of the image.

To change the size of the screen, just move the projec-

tor towards or away from the wall.

The size of the screen (b) is comprised between 50 and

100 inches depending on the projection distance (a), as

described in the following table.

Connect Power Supply

1Connect the power cord into the socket on the rear

side of your device (1).

2Plug the power cord to outlet on the wall (2).

Installing or Changing the

batteries of the IR Remote

Control

1To access the battery, press to unlock the locking

mechanism (1) and slide out the battery compart-

ment (2).

CAUTION!

Remove protection foil before operation!

Do not place any objects in front of the lens!

Diagonal size (b)

(mm)

[inch]

Projection distance

(a)

(mm)

1270

[50]

108

2540

[100]

441

CAUTION!

The power cord is used as a power unit cut

off. As a precaution, the outlet shall be located

close to the device and be of easy access in

case of danger.

DANGER!

Risk of Explosion with Incorrect Type of

Batteries

Only use the AAA type battery.

There is a risk of explosion if the incor-

rect battery type is used.

PHILIPS

VGA

S/PDIF

OPTICAL

AUDIO

OUT

TRIG

OUT

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 10 Jeudi, 12. février 2015 10:33 10

Initial Operation 11

2Insert the new batteries into the battery compart-

ment with the positive and negative poles as shown.

Make sure the polarities(+ and -) are aligned cor-

rectly.

3Push the battery compartment back into the

remote control until the locking mechanism

engages.

Using the Remote Control

The remote control can be used within an angle of 22.5

degrees and up to 10 meters from the device. When

using the remote control, no obstacle should be placed

between the remote control and remote sensor.

Installing or Changing the

batteries of the RF Remote

Control

1To access the battery, take an appropriate tool and

place it in the orifice as shown below, open the bat-

tery compartment.

Notice

Normally the batteries will last for around

one year. If the remote control stops working,

please replace the batteries. If the device is

not used for a long time, take out the batter-

ies. This will prevent leakage and possible

damage to the remote control.

The used batteries should be disposed of

according to the recycling regulations of your

country.

PHILIPS

22,5°

78 9

45 6

123

TUV WXYZ

PQRS

GHI JKL MNO

. @ ABC DEF

SUBTITLE TEXT

PAGE/CH - PAGE/CH +

EXIT

OPTIONS

TAB INFO

SOURCE

FORMAT

SETTINGS

EPG 3D

FAVORITE

PHILIPS

RECALL

SMART

CAUTION!

• The improper use of batteries can lead

to overheating, explosion, risk of fire

and injury. Leaking batteries can possibly

damage the remote control.

• Never expose the remote control to

direct sunlight.

• Avoid deforming, dismantling or charg-

ing the batteries.

• Avoid exposure to open fire and water.

• Replace empty batteries immediately.

• Remove the battery from the remote

control if not in use for long periods of

time.

DANGER!

Risk of Explosion with Incorrect Type of

Batteries

Only use the AAA type battery.

There is a risk of explosion if the incor-

rect battery type is used.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 11 Jeudi, 12. février 2015 10:33 10

12 Philips · HDP16x0TV

2Press the black latch locking.

3Lift the lever blue retention.

4Insert the new batteries into the battery compart-

ment with the positive and negative poles as shown.

Make sure the polarities(+ and -) are aligned cor-

rectly.

5Press the locking lever until you hear "CLICK" it

tells you that the closure is correct.

6Replace the battery cover in place and press down

to close.

Placing the USB receiver RF

Remote Control (RF)

Your remote control is recognized by the device with

the supplied USB receiver connected to a rear USB

port.”.

1Take the USB receiver and insert it into a USB port

on the device.

CLICK

Notice

Normally the batteries will last for around

one year. If the remote control stops working,

please replace the batteries. If the device is

not used for a long time, take out the batter-

ies. This will prevent leakage and possible

damage to the remote control.

The used batteries should be disposed of

according to the recycling regulations of your

country.

Notice

Respect the direction of insertion, do not

force any case!

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 12 Jeudi, 12. février 2015 10:33 10

Initial Operation 13

Using the RF remote control

Your remote uses radio waves to communicate with

your device.

1To activate the RF remote control, position yourself

in front the camera. Touch and hold the OK button

until the pointer on the screen appears.

2Now do move your remote control right and left

arrow moves as you move.

Stand ye in the desired menu or setting and press

OK to access.

3When you enter the text, return your RF remote

control and use the keyboard to enter your text.

Notice

Remote Control (RF) pairing

If the Screeneo does not react to RF remote

control commands, the remote control has to

be paired with the USB receiver again. For

renewing the pairing please connect the USB

receiver to a rear USB port of the Screeneo.

Then pressing the red and blue key on the

remote control together for 5 s to 10 s at the

same time.

Notice

The range of your remote control is

15 meters in direct line.

TEXT_

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 13 Jeudi, 12. février 2015 10:33 10

14 Philips · HDP16x0TV

3D glasses

The 3D glasses are equipped with a battery. They have

to be charged before first use.

1Take USB mini cable (supplied), connect the USB

mini on the 3D glasses and the another plug on a

USB port of the device.

Charging takes several hours and is complete when

the LED on the glasses is on green.

When the LED turns red, do a new charge.

Activate 3D glasses

1Press the ON / OFF button on the top of the

glasses.

2On the remote control, press the 3D button.

3The 3D menu appears, select your choice and press

OK.

4Press the ON/OFF button for one second and a half

on the 3D glasses .

The LED flashes green three times and becomes

fixed. Your glasses are ready.

1.5 SEC

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 14 Jeudi, 12. février 2015 10:33 10

Initial Operation 15

Initial Installation

1To turn on the projector, push the POWER B but-

ton once.

2Turn the device towards a suitable projection sur-

face or wall. Note that the distance to the projec-

tion surface must be a minimum of 0.1 meter and a

maximum of 0.5 meter (see Setting up the Device,

page 4). Make sure the projector is in a secure posi-

tion.

3Use the focus wheel on the font of the device to

adjust the image sharpness.

4The first time you turn on the device, you should

set the following settings.

5Use the keys / to select the language and

confirm with OK.

6Use the keys //À/Á to select the symbol

+ or - to set the date (day, month and year) and

confirm with .

7Use the keys / to select the date format and

confirm with .

8Use the keys / to select the time zone and

confirm with .

9Use the keys //À/Á to select the symbol

+ or - to set the date (hour and minute) and con-

firm with .

10 Use the keys / to select the time format (12h

or 24h) and confirm with .

11 Use the keys / to select the location (Home

or Shop) and confirm with .

Home: for normal use.

Shop: when you choose this option, the projector

starts in demonstration mode. In this mode, the

projector automatically displays the pictures or vid-

eos stored in the internal memory in loop.

12 A message is displayed «Open User Manual?»,

use the keys À/Á for select Yes or No. Press

 to continue.

The manual is displayed or the address web site

where the user manual can be downloaded.

Turning off the projector

Press the B button on the panel control of the device

or on the remote control more than 5 seconds.

ECO mode

Press shortly the B button on the panel control or on

the remote control to put the device in ECO mode.

To wake up the device, press shortly again on the

B button.

Setting up the Language

The device has already been installed. In order to

change the menu language, proceed as follows:

1Use the navigation keys to select Settings.

2Confirm with .

3Select Language/ Language with /.

4Confirm with .

5Select Menu Language with /.

6Confirm with .

7Select you desired language with /.

8Confirm with .

9Exit with u.

Notice

During the first installation, use OK key to

validate your choice and continue to the next

step, and the ¿ key to return on the previ-

ous step.

Notice

The demonstration mode can be activated or

deactivated on the menu Setting/Mainte-

nance/Demo mode.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 15 Jeudi, 12. février 2015 10:33 10

16 Philips · HDP16x0TV

4 Connect to the Playback Device

Connecting to Devices with

HDMI Output

Use the HDMI cable to connect the projector to a com-

puter, laptop or others devices.

1Switch the device on using the on/off key.

2Connect the cable to the projector's HDMI

socket.

3Connect the cable to the HDMI socket of the play-

back device.

4From the main menu, select HDMI 1,2 or 3

depending on the external device is connected.

Connecting to a Computer

(VGA)

Use the VGA cable (not included) to connect the pro-

jector to a computer, laptop, or some PDAs. The pro-

jector supports the following resolutions: VGA/SVGA/

XGA. For best results, please check the best resolution.

1Switch the device on using the on/off key.

2Connect the VGA cable to the projector's VGA

socket.

3Connect the VGA plug to the VGA socket of the

computer.

4Adjust the computer's resolution to the correct

setting and switch the VGA signal to an external

monitor. The following resolutions are supported:

5From the main menu, select VGA.

Notice

Use any of the HDMI sockets to connect the

projector to a DVD player when a 3D signal

is broadcasted.

PHILIPS

VGA

S/PDIF

OPTICAL

AUDIO

OUT

TRIG

OUT

HDMI 3

HDMI 1 & HDM 2

Notice

Many laptops do not activate the external

video output automatically when you connect

a second display such as a projector. Check

your laptop's manual to find out how to acti-

vate the external video output.

Resolution Image

refresh rate

VGA 640 x 480 60 Hz

SVGA 800 x 600 60 Hz

XGA 1024 x 768 60 Hz

WXGA 1280 x 768 60 Hz

FULL HD 1920 x 1080 60 Hz

Notice

Screen Resolution

For best results, please check the best resolu-

tion.

PHILIPS

VGA

S/PDIF

OPTICAL

AUDIO

OUT

TRIG

OUT

VGA

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 16 Jeudi, 12. février 2015 10:33 10

Connect to the Playback Device 17

Connecting Using an Audio/

Video (CVBS) Adapter

Cable

Use the projector's audio/video adapter cable (A/V

cable) (not included) to connect camcorders, DVD

players or digital cameras. The jacks for these devices

are yellow (video), red (audio right) and white (audio

left).

1Connect the A/V adapter to the  socket of the

projector.

2Connect the video device's audio/video sockets to

the A/V cable using a conventional composite video

(RCA) cable.

3From the main menu, select AV-in.

Connecting to mobile multimedia devices

Some video devices (e.g.: pocket multimedia players, ...)

require specific connection cables. There are either

supplied with the device or acquired from the manufac-

turer of the multimedia device. Please note that only the

original cables from the device manufacturer may func-

tion.

Connecting to a home

cinema amplifier

Use a S/PDIF optical cable (cable not provided) to con-

nect the DIGITAL AUDIO output on the projector to

the input of your home cinema amplifier.

For example, to show digital channels in DTS or

DOLBY DIGITAL quality sound.

Connecting to a Hi-Fi unit

It is possible to use an analog audio connection, just

connect the right and left audio outputs of the Projector

to the auxiliary input of your Hi-Fi system (cable not

provided).

Notice

Switching to the Multimedia Device Sig-

nal Output

See the multimedia device instruction manual

to find out how to switch the signal output to

this jack.

PHILIPS

VGA

S/PDIF

OPTICAL

AUDIO

OUT

TRIG

OUT

PHILIPS

VGA

S/PDIF

OPTICAL

AUDIO

OUT

TRIG

OUT

PHILIPS

VGA

S/PDIF

OPTICAL

AUDIO

OUT

TRIG

OUT

S/PDIF

OPTICAL

PHILIPS

VGA

S/PDIF

OPTICAL

AUDIO

OUT

TRIG

OUT

AUDIO

OUT

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 17 Jeudi, 12. février 2015 10:33 10

18 Philips · HDP16x0TV

Connecting the headphones

1Before connecting the headphones, turn down the

volume on the device.

2Connect the headphones to the projector's head-

phone slot. The device speakers deactivate auto-

matically when the headphones are connected.

3After connecting the headphones, increase the vol-

ume to a comfortable level.

WiFiDisplay (Miracast)

1Switch the device on using the on/off key.

2After the initial screen the main menu appears.

3Use the navigation keys to select APPs.

4Confirm with .

5Use the navigation keys to select WifiDisplay.

6Confirm with .

7Connect the external device (smartphone or tab-

let) to the same WiFi network that the projector.

8Select on the WifiDisplay application of the exter-

nal device the name of the projector connection (in

the example Screeneo_5f31).

9Connect the external device (smartphone or tab-

let) to the projector, it will show up connecting.

10 In the WifiDisplay application of the projector, it

will show up the message Invitation to connect,

Decline or Accept, select Accept.

Directly Connecting

Projector to Computer using

WLAN (WiFi Streaming)

With the ScreeneoWLink software you can connect the

projector to a computer or a laptop over your wireless

network. For this purpose, both devices must be con-

nected to the same wireless network.

1Intall the ScreeneoWlink software on your com-

puter. The ScreeneoWlink software is stored in the

Download folder, you can get it by SD card or USB

disk from the address: APPs_explorer_internal

flash_Download.

2Connect the device with the wireless network (see

also Wireless Network (WLAN), page 22).

3Start ScreeneoWLink (Viewer) on your computer.

4Click the ScreeneoWLink icon in the notification

area and start the manager window.

You are now able to search for projectors in the net-

work (Search WIFI projector) and start the projection

(Start projection).

ScreeneoWLink software

It allows to connect the projector to a desktop PC or

laptop via the wireless or wired network and to use the

Screeneo as computer screen.

For this, both devices must be connected to the same

wireless or wired network.

Screeneo firmware version 1.20 must be installed on

your projector.

Check the version of firmware installed on your projec-

tor by going to the Settings menu > Maintenance >

Firmware version.

If the Screeneo firmware version is 1.20, refer to para-

graph Install the ScreeneoWLink software on my com-

puter.

If the Screeneo firmware version is less than 1.20, refer

to paragraph Update the software in my projector.

DANGER!

Danger of Hearing Damage

Do not use the device over a longer time at

high volume – especially when using head-

phones. This could lead to the risks of hearing

damage. Before connecting the headphones,

turn down the volume on the device. After

connecting the headphones, increase the vol-

ume to a comfortable level.

Notice

Only the Miracast-certified devices can be

used with this function.

Notice

The projector must be connected to a WiFi

network.

Notice

The name used to identify the projector can

be modified in the Setting menu.

PHILIPS

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 18 Jeudi, 12. février 2015 10:33 10

Connect to the Playback Device 19

Update the software in my

projector

You can find the Screeneo firmware version on the site

« Philips »: www.philips.com/screeneo for loading the

file proceed as following

You must download the file on SD-card formatted

FAT16 or FAT32, on USB stick or on USB digital sup-

port in order to update your Screeneo.

Get yourself a suitable digital media and insert it into

your computer.

1Launch an Internet browser, in the address bar, type

the address: www.philips.com/screeneo.

2Choose your country and click on the language.

3Click on View All 4 Products for select your model.

4Select exactly your model with mouse.

5In the new screen, research Support and click on.

6The "Screeneo Smart LED projector" screen

appears. In the "Software & drivers" select your

language and click Download file.

7Depending on the browser used, save the file in the

root of your digital media.

8On the Screeneo projector, to check that it is turned

off (OFF).

9Remove the digital media on your computer and

insert it into the port of Screeneo for your digital

media.

11 Long press the ON/OFF button on the projector to

turn it on.

12 After the initial screen, the main menu appears. Use

the navigation keys to select Settings.

13 Confirm with OK.

14 Use / to select Maintenance.

15 Confirm with OK.

16 Use / to select Firmware Update.

17 Confirm with OK.

18 Use / to select Install.

19 Confirm with OK.

20 The device turns off and on again. After around 5

minutes the Language Selection screen appears. The

firmware update is now completed.

Copy the software on digital

media (eg USB-stick)

Use the USB ports on the projector to insert digital

media.

1Use / to select APPs.

2Confirm with OK.

3Use / to select Explorer.

4Confirm with OK.

5Use / to select Internal Flash.

6Confirm with OK.

7Use  to select Download.

8ScreeneoWLink_Setup.exe file appears in the main

window.

9Press long OK button on the remote control.

10 Use / to select Copy.

11 Confirm with OK.

12 Use //À/Á you move on to the digital

media that you have connected.

13 Confirm with OK.

14 Press long OK button on the remote control.

15 Use / to select Paste.

16 Confirm with OK.

17 ScreeneoWLink_Setup.exe file is copied to the digi-

tal media. Wait that it appears in the browser win-

dow before removing the digital media projector.

Install the ScreeneoWLink

software on my computer

1Insert the digital media containing the Screene-

oWLink_Setup.exe file on an appropriate port on

your computer.

2On desktop PC or laptop, select the digital media

containing the file and double click the executable.

3Follow the instructions that appear on the screen.

4Agree to have the ScreeneWLink icon on your desk-

top.

5When installation is complete, restart your com-

puter.

Notice

The file on the website is a zip file. It has to be

unpacked and put on the root folder of the

SD-card or USB-stick.

DANGER!

Inserting the digital media!

Never pull out the digital media while the

device is accessing it. This could cause data

to be damaged or lost.

Switch the device off in order to make sure

that the device does not access the

memory card.

Notice

If an error occurs during the firmware update

process retry the procedure or contact your

dealer.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 19 Jeudi, 12. février 2015 10:33 10

20 Philips · HDP16x0TV

Link your projector and computer

with WiFi

Both devices must be connected to the same access

point, no other network connection must be activated.

As a precaution, note the name and the key to protec-

tion of your access point.

On the Screeneo,

1Use / to select Settings.

2Confirm with OK.

3Using / select Wireless and Networks.

4Confirm with OK.

5Using / select WIFI.

6Confirm with OK.

7Using / select the desired wireless network.

8Confirm with OK.

9If your network is protected by a password, a win-

dow appears. Select the input field with the naviga-

tion buttons on the remote and press OK.

A virtual keyboard appears, using the navigation keys

on the remote control, witch a mouse or external

keyboard.

Enter your password.

10 Click Connect.

Start ScreeneoWLink on your PC

1Open the Start menu. Locate and open the Scree-

neoWLink tab. Click on ScreeneoWLink or double

click on ScreeneoWLink icon of your desktop.

2The ScreeneoWLink V1.2 software opens on the

screen.

3Stand on the projector image with the magnifying

glass and click it.

4Click Search.

5Select and click on the Screeneo where you want to

connect.

6If necessary, enter password of acces point selected.

You can enjoy the Screeneo as screen for your PC.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 20 Jeudi, 12. février 2015 10:33 10

Memory 21

5Memory

Inserting a Memory Card

1Insert a memory card with the contacts facing down-

wards into the / slot at the back of the

device. Your device supports the following memory

cards: SD/SDHC/SDXC/MMC.

2Insert the memory card into the slot until it snaps

into position.

3Press lightly on the memory card to remove it.

4The memory card is ejected.

Connecting USB Storage

Medium

1Connect the USB storage medium to one USB port

of the device.

DANGER!

Inserting a Memory Card!

Never pull out the memory card while the

device is accessing it. This could cause data

to be damaged or lost.

Switch the device off in order to make sure

that the device does not access the mem-

ory card.

PHILIPS

DANGER!

Inserting a Memory Card!

Never pull out the memory card while the

device is accessing it. This could cause data

to be damaged or lost.

Switch the device off in order to make sure

that the device does not access the mem-

ory card.

PHILIPS

VGA

S/PDIF

OPTICAL

AUDIO

OUT

TRIG

OUT

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 21 Jeudi, 12. février 2015 10:33 10

22 Philips · HDP16x0TV

6Network

The projector can be connected to the network by a

network hard-wired cable or through a wireless (Wi-Fi)

connection.

Use the procedure below appropriate to the type of

connection you want.

LAN Network

Connecting to the LAN network

1Connect one end of a LAN cable (not supplied) to

the ETHERNET port of your projector.

2Connect the other end of the LAN cable to the

network.

3Configure the LAN network settings in manual or

automatic configuration.

Automatic configuration

The automatic configuration of the local network set-

tings may be considered, if your local network features

a DHCP or BOOTP server that can dynamically assign

addresses to the peripheral devices present on the

LAN.

To automatically configure the local network settings:

1Switch the device on using the on/off key.

2After the initial screen, the main menu appears.

3Use the navigation keys to select Settings.

4Confirm with .

5Using / select Wireless and Networks.

6Confirm with .

7Using / select Lan.

8Confirm with .

9Using / select On.

10 Confirm with .

11 Using / select Advanced.

12 Confirm with .

13 Using / select Network address.

14 Confirm with .

15 Check that Automatic is selected.

Manual configuration

To configure your projector manually, you should

obtain the usual information used to set a peripheral

device (IP address, sub-network mask, network and

gateway address).

To configure the local network setting manually:

1Switch the device on using the on/off key.

2After the initial screen the main menu appears.

3Use the navigation keys to select Settings.

4Confirm with .

5Using / select Wireless and Networks.

6Confirm with .

7Using / select Lan.

8Confirm with .

9Using / select On.

10 Confirm with .

11 Using / select Advanced.

12 Confirm with .

13 Using / select Network address.

14 Confirm with .

15 Using / select Use static IP.

16 Confirm with .

17 Enter the settings IP-Address, Gateway, Net-

mask, DNS1 and DNS2.

18 Confirm with .

Wireless Network (WLAN)

In a wireless network (Wireless Local Area Network,

WLAN) at least two computers, printers or other addi-

tional devices communicate with each other over radio

waves (high frequency waves). Data transmission in the

radio network is based on the standards 802.11a,

802.11b, 802.11g and 802.11n.

Notice

Connection!

The LAN connection takes priority over the

Wi-Fi connection.

PHILIPS

VGA

S/PDIF

OPTICAL

AUDIO

OUT

TRIG

OUT

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 22 Jeudi, 12. février 2015 10:33 10

Network 23

Infrastructure Wireless Network

In an infrastructure network, multiple devices commu-

nicate via a central access point (gateway, router). All

data are sent to the access point (gateway, router) and

distributed from there.

Switching Wireless

Networking (WLAN) on/off

Wireless networking is deactivated by default. You have

the option of turning this function on.

1Switch the device on using the on/off key.

2After the initial screen the main menu appears.

3Use the navigation keys to select Settings.

4Confirm with .

5Using / select Wireless and Networks.

6Confirm with .

7Using / select WIFI.

8Confirm with .

9Modify the settings with /.

10 Confirm with .

The ¿ key takes you one step back in the menu.

Setting up a Wireless

Network (WLAN)

1Switch the device on using the on/off key.

2After the initial screen the main menu appears.

3Use the navigation keys to select Settings.

4Confirm with .

5Using / select Wireless and Networks.

6Confirm with .

7Using / select WIFI Selection.

8Confirm with .

9Use / to select the desired wireless network.

10 Confirm with .

11 If your wireless network is password protected, an

input window appears. Select the input field (see

Navigation for setting menu, page 8) using the nav-

igation keys of the remote control and press OK.

12 Enter the password with the virtual keyboard using

the navigation keys of the remote control or with

an external keyboard.

13 Click on Connect.

The ¿ key takes you one step back in the menu.

Setting up a Wireless

Network (WLAN) using the

Wizard

You can integrate your device very quickly and easily

into an existing wireless network using Wi-Fi Protected

Setup (WPS) or using a wireless network scan. Using

WPS, all important settings like network name (SSID)

are automatically configured and the connection pro-

tected with secure WPA Encryption.

Using Wi-Fi Protected Set-up

(WPS)

Using Wi-Fi Protected Setup (WPS), you can integrate

your device into an existing wireless network in two dif-

ferent ways very quickly and easily. You can activate the

tion (PBC), if your access point (Access Point, Router)

supports this method.

DANGER!

Information on Using WLAN!

The functioning of security systems, medical

equipment or sensitive devices can be dis-

rupted by the transmission power of the

device. Observe any usage regulations (or

restrictions) in the vicinity of such equipment.

The use of this device can affect the operation

of insufficiently shielded medical devices and

hearing aids and pacemakers through the

release of high frequency radiation. Also con-

sult a doctor or the manufacturer of the med-

ical device to establish whether these are suf-

ficiently shielded from external high frequency

radiation.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 23 Jeudi, 12. février 2015 10:33 10

24 Philips · HDP16x0TV

Using WPS with Push Button

Configuration (PBC)

1Switch the device on using the on/off key.

2After the initial screen the main menu appears.

3Use the navigation keys to select Settings.

4Confirm with .

5Using / select Wireless and Networks.

6Confirm with .

7Using / select WIFI Selection.

8Confirm with .

9Use / to select the desired wireless net-

work..

10 Confirm with .

11 Activate Push Button Configuration on the WLAN

access point. The WLAN access point and device

connect automatically and create a WPA protected

connection.

Wifi Hotspot

Use the portable Wi-Fi hotspot to share the device’s

network connection with computers or other devices

through the Wi-Fi network.

Activating WiFi hotspot

1Switch the device on using the on/off key.

2After the initial screen, the main menu appears.

3Use the navigation keys to select Settings.

4Confirm with .

5Using / select Wireless and Networks.

6Confirm with .

7Using / select WiFi Hotspot.

8Confirm with .

9Using / select Portable WiFi Hotspot.

10 Confirm with .

11 Using / select On.

12 Confirm with .

The projector is now visible by other Wifi devices.

Notice

Important!

The projector can work as an access point, if

only a wired lan network is installed in the

location of use.

Notice

Connection!

When the WiFi hotspot mode is activated, it

takes priority over the other connections.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 24 Jeudi, 12. février 2015 10:33 10

Network 25

Setting up a WiFI hotspot

To modify the WiFi hotspot name and define the secu-

rity level.

1Switch the device on using the on/off key.

2After the initial screen the main menu appears.

3Use the navigation keys to select Settings.

4Confirm with .

5Using / select Wireless and Networks.

6Confirm with .

7Using / select WiFi Hotspot.

8Confirm with .

9Using / select Setup WiFi hotspot.

10 Confirm with .

11 To modify the settings, use / keys to select

the desired parameter.

12 Using / select Save.

13 Confirm with .

Digital Living Network

Alliance (DLNA)

This device supports Digital Living Network Alliance

(DLNA). Using this standard you can quickly intercon-

nect your multimedia devices.

Switching DLNA on and off

The DLNA function is switched on by default. You have

the option of turning this function off.

1Switch the device on using the on/off key.

2After the initial screen the main menu appears.

3Use the navigation keys to select Settings.

4Confirm with .

5Using / select Wireless and Networks.

6Confirm with .

7Using / select DLNA Sharing.

8Confirm with .

9Modify the settings with /.

10 Confirm with .

The ¿ key takes you one step back in the menu.

Play Media Using DLNA

If DLNA enabled devices are located in the connected

network, then you can access them in media playback

and file management (see Media Playback, page 28).

DLNA Control

You can control the projector using another device (e.g.

a smartphone) using DLNA. To do this, see the instruc-

tion manual for the device in question.

Item Description

Network SSID Name of the WiFi hotspot.

This is the name used to iden-

tify your projector when it is

detected by another WiFi de-

vice.

To modify the name, select the

field and press . With the

keyboard, enter the new

name.

Security Select among the 3 levels of se-

curity.

• Open (without secu-

rity)

•WPA PSK

• WPA2 PSK

Password Select the field and press .

With the keyboard, enter the

new password.

Show password Check the box to display the

password.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 25 Jeudi, 12. février 2015 10:33 10

26 Philips · HDP16x0TV

7 Bluetooth

Activating the Bluetooth

connection

1Switch the device on using the on/off key.

2After the initial screen, the main menu appears.

3Use the navigation keys to select Settings.

4Confirm with .

5Using / select Wireless and Networks.

6Confirm with .

7Using / select Bluetooth.

8Confirm with .

9Use / to select on.

10 Confirm with .

The projector is now visible for the near external Blue-

tooth devices.

Setting up Bluetooth

parameters

1Switch the device on using the on/off key.

2After the initial screen, the main menu appears.

3Use the navigation keys to select Settings.

4Confirm with .

5Using / select Wireless and Networks.

6Confirm with .

7Using / select Bluetooth.

8Confirm with .

9Using / select the desired setting.

10 Confirm with .

11 Modify the desired settings.

Bluetooth speaker

The projector can be used as Bluetooth speaker. In this

mode, you can play music from smartphones or tablets.

The projector can only connect to, and play audio from

one device at a time.

Activating Bluetooth speaker

1Switch the device on using the on/off key.

2After the initial screen, the main menu appears.

3Depending on model, use the navigation keys to

select BT Speaker or APPs>BT Speaker.

4Confirm with OK.

5Press the Red key to power on the speaker.

Menu Description

Select device The list shows all paired devic-

es.

Paired device To unconnect or unpair the

paired device.

Notice

Bluetooth speaker connection!

Depending on the model of your device, the

bluetooth speaker can be activated from the

main menu (BT Speaker icon) or from the

APPs menu.

Notice

Remote control

You can also use the SOURCE or

OPTIONS key of the remote control.

Press the SOURCE key and select BT

Speaker or press OPTIONS key then

select SOURCE and BT Speaker.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 26 Jeudi, 12. février 2015 10:33 10

Bluetooth 27

6Press the Green key to make the speaker discov-

erable during 60 seconds.

7On your external device, activate the Bluetooth

connection and select the speaker name from the

list.

When the device is connected, his name is dis-

played on the top of the screen.

8Press the Green key to play music.

During music playback, the following actions are

available:

Red key: To stop the connection.

Green key: To make a pause.

Yellow key: To play the previous music.

Blue key: To play the next music.

Changing the name of the

Bluetooth speaker connection

This is the name used to identify your projector when

it is detected by another Bluetooth® device.

1Switch the device on using the on/off key.

2After the initial screen, the main menu appears.

3Depending on model, use the navigation keys to

select BT Speaker or APPs>BT Speaker.

4Press the Yellow key to rename the connection.

5Use the keyboard to enter the new name.

6Press OK to confirm.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 27 Jeudi, 12. février 2015 10:33 10

28 Philips · HDP16x0TV

8 Media Playback

Navigating in the media

Playback

To navigate in the memory media, use the following

keys: In order to optimize the navigation, you can select a file

type on the list:

•FOLDERS to view all files (photo, audio

and video).

•MOVIES to view videos files only.

• PICTURES to view photo files only.

• MUSIC to view audio files only.

Notice

Navigation Keys

All the keys shown are buttons on the remote

control.

Notice

Best Settings for Optimal Use

Read the informations on the best settings in

the chapter settings (see Settings, page 36) for

optimal use of your device.

Keys Action

 or To select folders or files in the

displayed list.

Á or  For directories, goes one level

down.

For files, starts the selected

media file.

À or ¿Goes one level up in the direc-

tory structure.

uExits to main screen.

Red key of the re-

mote control

Allows to set the repeat

mode for movie and music

files:

•: Play mode deacti-

vate (greyed).

•: Play only the

selected movie in loop.

•: Play all movies in

the selected directory

in loop.

•: Play all movies in

the media in loop.

Green key of the

remote control

Allows to set the slide show

parameters for picture files.

Allows to set the shuffle

mode for music files:

•: Shuffle mode

deactivate (greyed).

•: Shuffle mode acti-

vate.

Yellow key of the

remote control

Allows to display the pictures

as miniatures or in a list.

Blue key of the re-

mote control

Allows to delete the selected

file.

Keys Action

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 28 Jeudi, 12. février 2015 10:33 10

Media Playback 29

Video playback

Supported file formats

Supported file formats are *.avi, *.mov, *.mp4, *.mkv,

*.flv, *.ts, *.m2ts, *.3gp.

Video Playback (USB/SD Card/

Internal Memory/DLNA)

1Switch the device on using the on/off key.

2The main menu appears.

3Use the navigation keys to select the desired media

(USB, SD-card or DLNA):

Memory

Internal memory or SD card can be selected.

USB

- If only one USB key is connected the explorer

shows only the content of the USB.

- If more than one USB memory is connected,

select the desired USB memory first.

DLNA

The explorer searches for servers and shows them

in a list. Select the desired DLNA server.

4Confirm with .

The content of selected media is displayed.

5To only display the movies content, select Movie

using the keys /on the left of the screen.

6Confirm with .

7Use / to select the video file that you wish to

play.

8Press  or Á to start playback.

9Press ¿ to end the slide show and return to the

overview.

10 When you press ¿ again, you will return to the

main menu.

During playback you can adjust the volume using the

keys / or À/Á on the remote control. Press

or repeatedly to shut off the volume com-

pletely.

Photo Playback

Supported file formats

Supported file formats are JPEG, BMP, PNG and GIF.

Photo Playback (USB/SD Card/

Internal Memory/DLNA)

1Switch the device on using the on/off key.

2The main menu appears.

3Use the navigation keys to select the desired media

(USB, SD-card or DLNA):

SD-card

Internal memory or SD card can be selected!

USB

- If only one USB key is connected the explorer

shows only the content of the USB.

- If more than one USB memory is connected,

select the desired USB memory first.

DLNA

Notice

The use of color keys

The Red key allows to set the repeat mode:

•: Play mode deactivate (greyed).

•: Play only the selected movie in

loop.

•: Play all movies in the selected

directory in loop.

•: Play all movies in the media in loop.

The Blue key alows to delete the selected

file.

Notice

Displaying Video Files

Only those videos that are compatible

with the projector will be displayed.

Notice

Navigation During Playback

Review / forward: Press :/; on the

remote control.

Press T to stop or continue playback.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 29 Jeudi, 12. février 2015 10:33 10

30 Philips · HDP16x0TV

The explorer searches for servers and shows them

in a list. Select the desired DLNA server.

4Confirm with .

The content of selected media is displayed.

5To only display the picture content, select Picture

using the keys /on the left of the screen and

confirm with .

6The list of photos are displayed on the screen as an

overview.

7Use À/Á or / to select the image that you

want to start the slide show with.

8Press Green key to start the slide show.

9To modify the settings, use / keys to select

the desired parameter.

10 Press Green key to start the slide show.

11 Press  to pause the slide show.

12 Press ¿ to end the slide show and return to the

overview.

13 When you press u, you will return to the main

menu.

Slide Show with Background

Sound

1During the slide show, press  to display the menu

bar on the bottom of the screen.

2Using À/Á select Ó.

3Confirm with .

4Use / to select the file that you wish to play.

5To start the background sound confirm with .

6Adjust the volume level with the volume keys on

the remote control.

7If no input is made, the menu bar is hidden after 5

seconds.

Zoom and rotate functions

During the slide show, press OK key to display the con-

textual menu.

To perform a zoom, use the navigation keys to select

the symbol then press OK.

To rotate a picture, use the navigation keys to select the

symbol then press OK to rotate the picture 90°

clockwise.

Press ¿ return to the slide show.

Notice

The use of color keys

The Green key allows to set the slide show

parameters.

The Yellow key allows to display the pictures

as miniatures or in a list.

The Blue key allows to delete the selected

file.

Notice

Many Photos on the Memory Card or

the USB Medium

If there are a lot of photos on the memory

card or the USB storage medium it can

take a moment before the overview

appears.

Notice

The slide show can be started with the OK

key if the parameters have already been

set up.

Item Description

Time per slide To modify the photo display

frequency.

Off, 0, 2, 5, 10, 20, 30 and 60s

Repeat Off, Directory or All

Slide transition To modify the type of transi-

tion from one photo to anoth-

er (random or by theme).

Slideshow order Random or by order

Notice

Storage Location

Only files from the internal memory/Mem-

ory Card/USB Storage Medium can be

played.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 30 Jeudi, 12. février 2015 10:33 10

Media Playback 31

Music Playback

Supported file formats

Supported file formats are MP3 and WAV.

Music Playback (USB/SD Card/

Internal Memory/DLNA)

1Switch the device on using the on/off key.

2The main menu appears.

3Use the navigation keys to select the desired media

(USB, SD-card or DLNA):

SD-card

Internal memory or SD card can be selected!

USB

- If only one USB key is connected the explorer

shows only the content of the USB.

- If more than one USB memory is connected,

select the desired USB memory first.

DLNA

The explorer searches for servers and shows them

in a list. Select the desired DLNA server.

4Confirm with .

The content of selected media is displayed.

5To only display the music content, select Music

using the keys /on the left of the screen and

confirm with .

6Use / to select the file that you wish to play.

7Press  to start playback.

8Press T to stop or continue playback.

During playback you can adjust the volume using the

keys / or À/Á on the remote control. Press

or repeatedly to shut off the volume com-

pletely.

Notice

Switch off the Image Playback

You can switch off the screen while playing

music in order to save power by a long press

on the key.

Notice

The use of color keys

The Red key allows to set the repeat mode:

•: Play mode deactivate (greyed).

•: Play only the selected music in

loop.

•: Play all musics in the selected

directory in loop.

•: Play all musics in the media in loop.

The Green key allows to set the shuffle

mode:

•: Shuffle mode deactivate (greyed).

•: Shuffle mode activate.

The Blue key allows to delete the selected

file.

Notice

Navigating when Image Playback is

Switched off

Press / to skip to the previous or

next song.

Press T to stop or continue playback.

Press ¿ to return to the selection.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 31 Jeudi, 12. février 2015 10:33 10

32 Philips · HDP16x0TV

Managing Files

Delete Files

You can delete files from the internal memory, the con-

nected USB storage medium or the memory card.

1Switch the device on using the on/off key.

2The main menu appears.

3Use the navigation keys to select the desired media

(USB, Memory or DLNA).

4Confirm with .

5Use / to select the file that you want to

delete.

6Press the Blue key on the remote control to

delete the file.

7Confirm with .

Notice

Error

If errors occur during the deletion pro-

cess, make sure that the storage medium is

not write-protected.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 32 Jeudi, 12. février 2015 10:33 10

Digital TV Playback (Depending on model) 33

9Digital TV Playback

(Depending on model)

Connecting the Aerial

1Connect the aerial to the aerial socket.

First Playback

When the DVB-T function is first started, the automatic

channel search must be started.

1Switch the device on using the on/off key.

2The main menu appears.

3Connect the aerial (see Connecting the Aerial,

page 33).

4Use the navigation keys to select TV.

5Confirm with .

6Use / to highlight a setting and use the À/

Á to select a value.

- Select the country.

- Select the level of the parental control.

- Enter the PIN code for channel lock or parental

control. Enter the code with 4 digits (0000 is not

accepted) and enter again the same code to con-

firm.

7Press OK to confirm the settings and continue the

installation.

The channel search starts automatically.

8At the end of the search, press .

9Your TV is now set. You can start watching and

enjoying all your channels.

Notice

Aerial Size and Orientation

In some regions it is necessary to connect a

larger aerial in order to grant the reception.

In some countries it is necessary to point the

aerial horizontally in order to grant the recep-

tion.

PHILIPS

VGA

S/PDIF

OPTICAL

AUDIO

OUT

TRIG

OUT

Notice

Navigation Keys

All the keys shown are buttons on the remote

control.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 33 Jeudi, 12. février 2015 10:33 10

34 Philips · HDP16x0TV

Television

1Switch the device on using the on/off key.

2The main menu appears.

3Use the navigation keys to select TV.

4Confirm with OK.

5The last viewed channel is played. Change the chan-

nel using keys CH+/CH-, / or enter directly

the number with the keypad.

6Press u to end playback and return to the main

menu.

During playback you can adjust the volume using the

keys / or À/Á on the remote control. Press

or repeatedly to shut off the volume com-

pletely.

Modifying the DVB-T

settings

To modify DVB-T settings, press the Menu key on the

remote control. Main menus are:

Edit channels: To display and modify the channel and

radio lists.

Installation: To launch an automatic or a manual

search for channels.

System Setup: To modify the parental lock settings,

the display settings and the favorite settings.

Notice

Navigation Keys

All the keys shown are buttons on the remote

control.

Notice

Displaying Channel Information

When changing channel, channel informa-

tion is displayed on the bottom projection

edge. The information bar is hidden after 5

seconds.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 34 Jeudi, 12. février 2015 10:33 10

Android 35

10 Android

Your projector uses the Android operating system.

Starting Android Apps

1Switch the device on using the on/off key.

2After the initial screen the main menu appears.

3Use the navigation keys to select APPs.

4Confirm with OK.

Exiting Android

Press the u key to return to the main menu.

Installing Android-Apps

You can install other apps. Use the APK installation

packets, proceed as follows:

1Download the package APK and save it onto a mem-

ory card or USB-stick.

2Insert the memory card into the device (see Insert-

ing a Memory Card, page 21).

3Switch the device on using the on/off key.

4After the initial screen the main menu appears.

5Use the navigation keys to select APPs

6Confirm with OK.

7Use the navigation keys to select ApkInstaller.

8Confirm with OK.

9Use the navigation keys to select Install.

10 Confirm with OK.

11 Navigate to the memory card and select the APK

package you want to install.

12 Press OK to execute the installation package.

13 The APK package is installed.

CAUTION!

Trusted Sources!

Apps from third party sources may be mali-

cious. Only use installation packets from

trusted sources.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 35 Jeudi, 12. février 2015 10:33 10

36 Philips · HDP16x0TV

11 Settings

1Switch the device on using the on/off key.

2After the initial screen the main menu appears.

3Use the navigation keys to select Settings.

4Confirm with OK.

5Use / to select from the following settings.

6Confirm with OK.

7Modify the settings using OK, /,

8Confirm with OK.

The ¿ key takes you one step back in the menu.

Overview of the Menu

Functions

Wireless and Network

WiFi – switching the wireless network (WLAN) off

and on.

Network Selection – select the wireless network

with which the device is to connect.

WiFi Hot Spot – activate and deactivate WLAN

tethering.

LAN – switching the LAN network (LAN) off and

on.

Advanced – (LAN mode only) check the Network

actual IP address or change the address by inputting

new address. You can also select Automatic or

Use static IP

DLNA Sharing – switching DLNA off and on.

Bluetooth – switching the Bluetooth connection off

and on.

Image settings

3D – set the picture modes with 2D/3D options.

Keystone – use / to set the keystone.

Fit Screen – use / to select the screen mode

to adjust the size of your screen.

Projection mode

Front – normal projection; the device is located

in front of the projection surface/screen

Rear – rear projection; the device is located

behind the projection surface; the image is

reflected horizontally.

Front Ceiling – the device is hanging from the

ceiling in an upside-down position; the image is

rotated by 180 degrees.

Rear ceiling – the device is located behind the

projection surface, hanging from the ceiling in an

upside-down position; the image is rotated by

180 degrees and reflected horizontally.

Wall color correction – colour correction of the

projected image to adjust to coloured projection

surfaces

Smart Settings – select predefined settings for

brightness / contrast / colour saturation. If you mod-

ify these settings, the setting is switched to Manual.

Brightness – use / to adjust the brightness

and press OK to confirm.

Contrast – use / to adjust the contrast and

press OK to confirm.

Advanced

Colour temperature – set to Warm to enhance

hotter colors such as red, or set to Cool to

make picture bluish.

Dynamic contrast – adjusts the contrast to

keep it at the best level according to the bright-

ness of the screen.

Color space – to convert the color space set-

ting to another standard.

Gamma – adjusts the gamma correction

according to the type of the projected image.

Manual colors RGB – manually adjust the hue, sat-

uration and brightness of colors in RGB mode. Use

//À/Á to adjust the colors according to

your needs.

Manual colors CMY – manually adjust the hue, sat-

uration and brightness of colors in CMY mode. Use

//À/Á to adjust the colors according to

your needs.

Reset – valid manual modifications of colors RGB

and CMY.

Sound Settings:

Volume – adjust the volume

Deep Bass – switching the deep bass on and off

Wide sound – switching the wide sound on and off

Equalizer – select the equalizer mode

Smart volume – turn on/off the volume level auto-

matic control function

Key beep – turn key tones on and off

Speaker – switching the speaker on and off

System settings

Date and time – set date and time

Android Settings – set Android system

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 36 Jeudi, 12. février 2015 10:33 10

Settings 37

Sleep mode – With this function, the projector

automatically goes to ECO mode after a specified

period of time or at the end of a movie.

Auto Power Down (APD) – turn on/off the auto

power down.

The default setting is depending on the choice of:

- shop mode: APD off,

- dome mode on: APD off,

- home mode: APD on.

When the parameter is switched on, it works like

this:

- it should go into off mode after 3 hours.

If a video is displayed, the APD should take place 3h

after last user action, meaning that a pop-up will

appear after 2h58 for 2 minutes, indicating that the

product will go into off mode.

HDMI name – select this item to change the HDMI

names. Name that appears on the main screen.

Language/Language

Menu language – use / to select the desired

language and press OK to confirm.

Soundtrack – use / to select the desired lan-

guage and press OK to confirm.

Sub Title – use / to select the desired lan-

guage and press OK to confirm.

Maintenance

Reset settings – Reset settings to factory defaults.

Firmware Update – Update Firmware

Information – Display free space in the internal

memory and information on the device (Capacity: /

Free space: / Firmware version: / Device name: /

Model:)

Demo mode – switching demo mode on and off. In

this mode, Screeneo is continuously displayed on

the screen and video and/or audio files placed in

internal memory are read directly.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 37 Jeudi, 12. février 2015 10:33 10

38 Philips · HDP16x0TV

12 Service

Cleaning

Cleaning the Lens

Use a brush or lens cleaning paper for cleaning the lens

of the projector.

Device Overheated

A overheat symbol appears if the device is overheated.

Update Firmware with

Memory Card

1Use SD memory card in the file system FAT16 or

FAT32.

2Save the latest firmware update file to the root of

the memory card.

3Insert the memory card (see Inserting a Memory

Card, page 21) and switch the device on.

4Use the navigation keys to select Settings.

5Confirm with à.

6Use / to select Maintenance.

7Confirm with à.

8Use / to select Firmware Update.

9Confirm with à.

10 Use / to select Install.

11 Confirm with à.

12 The device turns off and on again. After around 5

minutes the Language Selection screen appears.

The firmware update is now completed.

DANGER!

Instructions for Cleaning!

Use a soft, lint-free cloth. Never use liquid or

easily flammable cleansers (sprays, abrasives,

polishes, alcohol, etc.). Do not allow any

moisture to reach the interior of the device.

Do not spray the device with any cleaning flu-

ids.

Wipe over the surfaces gently. Be careful that

you do not scratch the surfaces.

DANGER!

Do not use any Liquid Cleaning Agents

Do not use any liquid cleaning agents for

cleaning the lens, to avoid damaging the coat-

ing film on the lens.

DANGER!

All Data will be Deleted!

This procedure erases all your data that is

stored on the memory card.

DANGER!

Inserting a Memory Card!

Never pull out the memory card while the

device is accessing it. This could cause data

to be damaged or lost.

Notice

If an error occurs during the firmware update

process retry the procedure or contact your

dealer.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 38 Jeudi, 12. février 2015 10:33 10

Service 39

Troubleshooting

Power Cycling

If a problem occurs that cannot be corrected with the

instructions in this user manual (see also the help

below), follow the steps given here.

1Switch the device off using the on/off key on the

panel control.

2Wait at least ten seconds.

3Switch the device on using the on/off key on the

panel control.

4If the problem repeats, please contact our technical

customer service or your retailer.

Problems Solutions

The projector cannot be switched on • Disconnect and Connect the power supply cable and

try again.

The projector cannot be switched off • Disconnect the power supply cable.

No sound • check that the speaker is activated (Settings /Sound

setting/Speaker).

• Adjust the volume using the / key on the

remote control.

No sound from the external connected device • Check the cables to the external device

• Set the volume on the external device

• Only the original cables from the device manufac-

turer may function

No sound from DVB-T program or external HDMI out-

put device.

• Set the audio setting to Multichannel (Raw data) &

Stereo (PCM).

No sound when you connect your computer via HDMI

cable

• Check that the sound is activated on the computer.

Video display problem when the source is a 3D signal

from a DVD player.

• Check that the 3D mode is activated on the projec-

tor.

• If the DVD player is connected to the projector via

HDMI, use any of the HDMI sockets.

Only the initial screen appears and not the image from

the external device

• Check if the cables are connected to the right sock-

ets.

• Please check that the external device is switched on

• Check if the video output of the external device is

switched on.

• Check that the HDMI source selected on the user

interface corresponds to HDMI connector where

the external device is connected.

Only the initial screen appears and not the image from

the connected computer

• Please check that the VGA-output of the computer

is switched on.

• Check if the resolution of the computer is set to

1280*800 (for VGA connection) or 1080P(for HDMI

connection).

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 39 Jeudi, 12. février 2015 10:33 10

40 Philips · HDP16x0TV

The device turns itself off • When the device is running for a long period of time,

the surface becomes hot and a warning symbol

appears on the projection (see Symbols in the Status-

bar, page 9). The device automatically turns off when

it gets too hot. After the device has cooled down,

you can continue playback.

• Check that the power cable is connected correctly.

• Check the sleep mode status in the setting menu ().

When the sleep mode is activated, the device turn

off after the programmed duration.

The device changes from maximum level of brightness to

minimum level of brightness when the device is connect-

ed over USB to play videos.

• When the environment temperature is too high, the

devices turns automatically from maximum level of

brightness to minimum level of brightness in order to

protect the high power LED.

• Use the device with lower environment tempera-

tures.

The device cannot connect with an Android device (for

example a mobile phone/smartphone with the Android

operating system) when connected via USB.

• Deactivate the function „USB debugging“ in the set-

tings menu of your Android device before connect-

ing the Projector via USB; your Android device

should be recognized as USB storage medium.

Bad image or color quality when connecting with HDMI • Use a high quality HDMI cable. Low quality cables

may cause signal distortions.

The device cannot read the SD card. • Check that the memory card is compatible (see the

list in the chapter Appendix).

The device cannot read the USB stick • The device does not support the exFAT file system.

• Format the USB key in FAT format, then use it.

The TV icon doesn't appear while the DVB-T module is

installed.

• Call the hot-line.

The projector does not react to remote control com-

mands when using the RF remote control.

• Check if the remote control batteries are new.

• The remote control has to be paired with the USB

receiver again. For renewing the pairing please con-

nect the USB receiver to a rear USB port of the

Screeneo. Then pressing the red and blue key on the

remote control together for 5 s to 10 s at the same

time.

Problems Solutions

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 40 Jeudi, 12. février 2015 10:33 10

Appendix 41

13 Appendix

Technical Data

Dimensions (L×H×W) .................... 287 × 148× 339 mm

Weight ........................................................................... 5,3 kg

Recommended Ambient ......................................5 – 35 ºC

Relative Humidity ................15 – 85 % (non-condensing)

File format................................ *.avi, *.mov, *.mp4,*.mkv,

................................................ *.flv, *.ts, *.m2ts, *.3gp

Photo formats ................................. JPEG, BMP, PNG, GIF

Music formats..................................................... MP3, WAV

Video Standard (CVBS)................... PAL, SECAM, NTSC

Video connection .........................................HDMI sockets

Internal speaker ............... stereo with subwoofer, 26 W

Internal memory............................................................4 GB

Compatible Memory Cards ......SD/SDHC/SDXC/MMC

USB connection max. power...........................5V, 500mA

Technology / optical

Display technology ...............................WXGA 0.45" DLP

Light source ........................................................... RGB LED

Native resolution......................... 1280 x 800 Pixel (16:9)

Supported Resolutions..................... VGA/SVGA/WVGA

..............................................XGA/WXGA/FULL HD

Projected image size (inch)...........................50 up to 100

Screen distance (mm).................................. 108 up to 441

Display refresh rate ............................. 60Hz/50Hz/120Hz

Power supply

Input .......................................100V-240V, 4.0 A, 50/60HZ

Power consumption....................................................150W

Off mode power consumption .............................. <0,5W

Manufacturer .................................... JQH Group Co., Ltd.

Accessories

Following accessories are available for your device:

PVideo-(CVBS) cable.....................PPA1320 / 253526178

3D Glasses.......................................PPA5610 / 253569764

For HDP1650 an HDP1650TV models:

RF remote control.........................PPA5650 / 253588194

All data are provided for reference purposes only.

Sagemcom Documents SAS reserves the right to

make any changes without prior notice.

The CE marking certifies that the product meets the

main requirements of the European Parliament and

Council directives 1999/5/CE, 2006/95/CE, 2004/108/

CE and 2009/125/CE on information technology equip-

ment, regarding safety and health of users and regarding

electromagnetic interference.

The declaration of compliance can be consulted on the

site www.screeneo.philips.com.

Preservation of the environment as part of a sustainable

development plan is an essential concern of Sagemcom

Documents SAS. The desire of Sagemcom Documents

SAS is to operate systems observing the environment.

The desire of Sagemcom Documents SAS is to operate

systems observing the environment and consequently it

has decided to integrate environmental performances in

the life cycle of this products, from manufacturing to

commissioning use and elimination.

Packaging: The presence of the logo (green dot)

means that a contribution is paid to an approved

national organisation to improve package recovery and

recycling infrastructures. Please respect the sorting

rules set up locally for this kind of waste.

Batteries: If your product contains batteries, they

must be disposed of at an appropriate collection point.

Product: The crossed-out waste bin stuck on the

product means that the product belongs to the family of

electrical and electronic equipment. In this respect, the

European regulations ask you to dispose of it selectively;

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 41 Jeudi, 12. février 2015 10:33 10

42 Philips · HDP16x0TV

• At sales points in the event of the purchase of

similar equipment.

• At the collection points made available to you

locally(drop-off centre, selective collection, etc.).

In this way you can participate in the re-use and upgrad-

ing of Electrical and Electronic Equipment Waste, which

can have an effect on the environment and human

health.

The paper and cardboard packaging used can be dis-

posed of as recyclable paper. Have the plastic wrapping

recycled or dispose of it in the non-recyclable waste,

depending on the requirements in your country.

Trademarks: The mentioned references in this man-

ual are trademarks of the respective companies. The

lack of the trademarks É and Ë does not justify the

assumption that these dedicated terminologies are free

trademarks. Other product names used herein are for

identification purposes only and may be trademarks of

their respective owners. Sagemcom Documents SAS

disclaims any and all rights in those marks.

Neither Sagemcom Documents SAS nor its affiliates

shall be liable to the purchaser of this product or third

parties for damages, losses, costs, or expenses incurred

by the purchaser or third parties as a result of accident,

misuse, or abuse of this product or unauthorized mod-

ifications, repairs, or alterations to this product, or fail-

ure to strictly comply with Sagemcom Documents SAS

operating and maintenance instructions.

Sagemcom Documents SAS shall not be liable for any

damages or problems arising from the use of any

options or any consumable materials other than those

designated as original Sagemcom Documents SAS /

PHILIPS products or Sagemcom Documents SAS /

PHILIPS approved products.

Sagemcom Documents SAS shall not be held liable for

any damage resulting from electromagnetic interference

that occurs from the use of any interface cables other

than those designated as Sagemcom Documents SAS /

PHILIPS products.

reproduced, stored in a retrieval system or transmitted

in any form or by any means, electronic, mechanical,

photocopying, recording, or otherwise, without the

prior written permission of Sagemcom Documents SAS.

The information contained herein is designed only for

use with this product. Sagemcom Documents SAS is not

responsible for any use of this information as applied to

other devices.

This user manual is a document that does not represent

a contract.

Errors, printing errors and changes are reserved.

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 42 Jeudi, 12. février 2015 10:33 10

HDP16x0TV

253637294-A

PHILIPS and the PHILIPS’ Shield Emblem are registered trademarks of Koninklijke Philips N.V.

and are used by Sagemcom Documents SAS under license from Koninklijke Philips N.V.

È 2015 Sagemcom Documents SAS

Sagemcom Documents SAS

Documents Business Unit

Headquarters : 250, route de l’Empereur

92848 Rueil-Malmaison Cedex · FRANCE

Tel: +33 (0)1 57 61 10 00 · Fax: +33 (0)1 57 61 10 01

www.sagemcom.com

Simplified Joint Stock Company · Capital 8.479.978 € · 509 448 841 RCS Nanterre

Screeneo_User-Manual_HDP16x0_TV_EN_253637294-A.book Page 43 Jeudi, 12. février 2015 10:33 10

Table of Contents

Philips HDP1690TV User Manual

Related Manuals