Philips S529 User Manual
Displayed below is the user manual for S529 by Philips which is a product in the Men's Shavers category. This manual has pages.
Related Manuals
使用本产品
拆卸或安装卡入式附件
1 确保产品电源已关闭。
2 将附件的凸缘插入本产品顶
部的槽内。然后，按下附件
将其安装到本产品上（可听
到“咔哒”一声）(图5)。
3 将附件竖直抽离产品(图6)。
注意：将附件从产品上抽出
时，不要旋转。
打开或关闭产品
1 要打开本产品，请向上
(图7)滑动开/关按钮。
2 要关闭本产品，请向下
(图8)滑动开/关按钮。
剃须
皮肤适应期
前几次剃须可能不会带给您预期
效果，并且您的皮肤可能会受到
轻度刺激。这是正常的。您的
皮肤和胡须需要时间适应任何新
的剃须系统。为了让您的皮肤
适应这款新产品，我们建议您在
3周时间内定期（至少每周
3次）仅使用本产品剃须。
干剃
1 启动产品。
2 让剃须刀头在您的皮肤上作
迂回运动，以刮剃向不同方
向(图9)生长的所有须发。
轻轻按压，以获取舒适贴面
的剃须感受。
注意：不要用力按压剃须
刀，这样做可能会导致皮肤
受刺激。
3 使用(请参见'清洁和保养‘)
后要清洁本产品。
清洁和保养
在水龙头下冲洗剃须刀
每次剃须后请清洁剃须刀，
以获得出色性能(请参见'清洁
和保养‘)。清洁前，务必拔下
电源并关闭剃须刀。
切勿使用压缩气体、钢丝绒、
研磨性清洁剂或腐蚀性液体
（例如汽油或丙酮）清洁本产品。
使用热水要当心。 切记先检查
水温是否太高，以防烫手。
不要用毛巾或纸巾擦拭剃须刀
头部件，因为这样可能会损坏
剃须刀头。
1 用温水冲洗剃须刀头部件。
注意：您也可以使用随附的
清洁刷清洁剃须刀头部件。
2 将剃须刀倒置，冲洗剃须刀
头支架底部的开口。在冲洗
(图10)过程中需短暂开启剃
须刀。
3 打开两个剃须刀头支架
(图11)。
4 在水龙头(图12)下冲洗胡茬
储藏室和剃须刀头支架。
5 小心地甩掉多余的水份然后
彻底晾干。
6 合上剃须刀头支架(图13)。
彻底清洁
剃须刀头部件包含两个剃须刀
头。按以下步骤一次清洁一个
剃须刀头。
1 打开剃须刀头支架(图11)。
2 要解锁固定架，请轻轻挤压
固定架的两侧，然后翻开固
定架(图14)。
3 取下剃须刀头。每个剃须刀
头包含一组刀片和网罩
(图15)。
注意：不要同时清洁多组刀
片和网罩，因为它们都是相
互匹配的。如果不小心将剃
须刀头的刀片和网罩弄混，
则需要数周时间才能恢复产
品的最佳剃须效果。
4 从网罩(图16)上取下刀片。
5 用清水冲洗这两个部件。
6 清洁后，将刀片重新装回至网
罩，刀片底部朝下(图17)。
7 将剃须刀头装回到剃须刀头
支架(图18)中。
注意：安装剃须刀头(图20)
时，确保带凸起的剃须刀头
正好卡入剃须刀头支架的挂
钩。本产品随附的剃须刀头
都带有槽口或凸起。这两组
剃须系统完全相同。
8 将固定架推回到剃须刀头支
架上，直至听到“咔哒”
(图19)一声。
9 合上剃须刀头支架(图13)。
更换
更换剃须刀头
为获得最佳剃须效果，建议每
两年更换一次剃须刀头。立即
更换损坏的剃须刀头。务必使
用原装飞利浦剃须刀头(请参见
'订购配件‘)进行更换。
1 关闭产品。
2 打开两个剃须刀头支架
(图11)，即打开剃须刀头部
件。
3 要解锁固定架，请轻轻挤压
固定架的两侧，然后翻开剃
须刀头(图14)。
4 从剃须刀头支架(图15)上卸
下剃须刀头。
立即扔掉用过的剃须刀头，
以免与新的剃须刀头混淆。
5 将新的剃须刀头装到剃须刀
头支架中。
注意：安装剃须刀头(图20)
时，确保带凸起的剃须刀头
正好卡入剃须刀头支架的挂
钩。本产品随附的剃须刀头
都带有槽口或凸起。这两组
剃须系统完全相同。
6 将固定架推回到剃须刀头支
架上，直至听到“咔哒”
(图19)一声。
7 合上剃须刀头支架(图13)。
存放
务必将保护盖滑到剃须刀头部
件上，以防止剃须刀头部件积
聚灰尘，或在旅行过程中或存
放(图21)时受损。
我们建议您先将产品晾干，
然后再进行存放。
订购配件
要购买附件或备件，请访问
www.shop.philips.com/service
或联系您的飞利浦经销商。您
还可以联系所在国家/地区的飞
利浦客户服务中心（请参阅全
球保修卡了解详细联系信息）。
可用部件
可选配以下附件和备件：
-SH30飞利浦剃须刀头
-HQ110清洁喷雾剂
-A00390电源部件
注意：附件可能因国家/地区
而异。
回收
-弃置本产品时，请不要将其
与一般生活垃圾放在一起，
应将其交给政府指定的回收
中心。这样做将有利于环
保。
-此产品包含内置充电电池；
请勿将充电电池与一般生活
垃圾一起弃置。强烈建议您
将自己的产品送到官方收集
点或飞利浦服务中心，让专
业人士移除充电电池。
-遵循您的国家/地区有关分类
回收电子电气产品和充电电
池的规定。正确弃置产品有
助于避免对环境和人类健康
造成不良后果。
拆下充电电池
仅在丢弃剃须刀时方可取出充
电电池。 卸下电池之前，请确
保剃须刀与电源断开连接并且
电池电量已耗尽。
当您使用工具打开剃须刀时，
请采取必要的安全保护措施。
注意，电池带非常锋利。
1 断开本产品电源并让其继续
运行，直到马达停止。
2 将螺丝刀插入前面板的上侧
边缘，卸下面板(图22)。
3 拧下剃须刀(图23)顶部的
螺丝。
4 卸下手柄(图24)上方的盖子。
5 将螺丝刀插入前面板的边
缘，卸下面板和开/关按钮
(图25)。
6 取出位于开/关按钮(图26)
下方的内部小部件。
7 用螺丝刀(图27)将内层固定
架从外壳中推出。
8 用钳子剪断电线，然后取出
电池(图28)。
故障种类和处理方法
本章归纳了使用本产品时最常
见的一些问题。如果您无法根
据以下信息解决问题，请访问
www.philips.com/support查阅
常见问题列表，或联系您所在
国家/地区的客户服务中心。
问题 可能的
原因
解决方法
剃须刀
的剃须
效果没
有以前
好。
剃须刀
头已损
坏或磨
损。
更换剃须刀
头(请参见
'更换')。
剃须刀
头很
脏。
清洁剃须刀
头(请参见
'清洁和保
养')。
较长的
胡须堵
塞了剃
须刀
头。
清洁剃须刀
头(请参见
'清洁和保
养')。
充电电
池的电
量不
足。
关闭剃须刀
并为电池
(请参见'充
电')充电。
启动剃
须刀
后，剃
须刀无
法工
作。
充电电
池的电
量已耗
尽。
关闭剃须刀
并为电池(
请参见'充
电')充电。
剃须刀
头无法
固定在
剃须刀
头部件
内。
未正确
固定固
定架。
将固定架推
回剃须刀头
上时，听
到“咔哒”
一声后，即
表明固定架
已固定到
位。
未正确
放置带
有凸起
部位的
剃须刀
头。
安装剃须刀
头(图20)
时，确保带
凸起的剃须
刀头正好
卡入剃须刀
头支架的挂
钩。
珠海经济特区飞利浦家庭电器有限公司
中国珠海市三灶镇琴石工业区
全国顾客服务热线: 4008 800 008
本产品根据国标 GB4706.1-2005,
GB4706.9-2008制造
产品：飞利浦电动剃须刀
型号：S529, S528, S526
额定电压：220V～
额定频率：50Hz
额定输入功率：2 W
生产日期：请见产品本体
产地：中国广东珠海
保留备用
发行日期:12/05/2017
мȞġĈҴˀΙĀǩ؆Ӎߒʔ
ˌɫǩ؆
ĈҴˀΙ
(Pb)
᰽
(Hg)
⬡
(Cd)
ԣᲱ
(Cr (VI) )
Ġ⅑ԓ᧠
(PBB)
Ġ⅑ȕ᧠⓭
(PBDE)
PCB’s
מŪǗɢذ XOOO
OO
Electrical
contact pins
ǗˈǦ
XOOO
OO
Power plug
Ǘ۷Ǽ XOOO
OO
ǕȪϜ֪֙SJ/T 11364Āܪǭৠ뺯
OȪФ˽ĈҴˀΙć˽ˌɫǨĈߴΙࠒնġĀߒʔߴćGB/T 26572ܪǭĀՄʔđŘĪ뺯
XȪФ˽ĈҴˀΙψɺć˽ˌɫĀԚĂߴΙࠒնġĀߒʔɸŜGB/T 26572ܪǭĀՄʔđ
뺯
-该表格中所显示的“有害物质”在产品正常使用情况下不会对人
身和环境产生任何伤害。
-该表格中所显示的“有害物质”及其存在的部件向消费者和回收
处理从业者提供相关物质的存在信息，有助于产品废弃时的妥善
处理。
4222.002.7315.1
www.philips.com
2
1
3
4
5
6
13
12
11
7
8
9
10
1
>75% recycled paper
>75%
S529, S528,
S526
17
20
23
26
18
21
24
19
22
25
27
1
2
3
28
2
5
8
11
2
1
1
14
1
2
3
6
9
12
4
7
10
13
15 16
4222_002_7315_1_DFU-Leaflet_55x99_v2.indd 1 12/05/17 12:00
ENGLISH
Congratulations on your purchase and
welcome to Philips! To fully benet from
the support that Philips oers, register
your product at www.philips.com/
welcome.
General description (Fig. 1)
1 Protection cap
2 Shaving head holder
3 Shaving unit connector
4 Handle
5 On/o indication
6 On/o button
7 Socket for small plug
8 Cutter
9 Guard
10 Retaining frame
11 Supply unit
12 Charging light
13 Small plug
Not shown: cleaning brush
Important safety information
Read this important information
carefully before you use the appliance
and its accessories and save it for future
reference. The accessories supplied
may vary for dierent products.
Danger
-Keep the supply unit dry (Fig. 2).
Warning
-To charge the battery, only use the
detachable supply unit (A00390)
provided with the appliance.
-The supply unit contains a
transformer. Do not cut o the
supply unit to replace it with
another plug, as this causes a
hazardous situation.
-This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe
way and understand the hazards
involved. Children shall not play with
the appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
-Always unplug the shaver before
you clean it under the tap.
-Always check the appliance before
you use it. Do not use the appliance
if it is damaged, as this may cause
injury. Always replace a damaged
part with one of the original type.
-Do not open the appliance to
replace the rechargeable battery.
Caution
-Never immerse the shaver in water.
Do not use the shaver in the bath or
in the shower.
-Never use water hotter than 60°C to
rinse the shaver.
-Only use this appliance for its
intended purpose as shown in the
user manual.
-For hygienic reasons, the appliance
should only be used by one person.
-Never use compressed air, scouring
pads, abrasive cleaning agents or
aggressive liquids such as petrol or
acetone to clean the appliance.
-Water may drip from the bottom of
the shaver when you rinse it. This is
normal and not dangerous because
all electronics are enclosed in a
sealed power unit inside the shaver.
-Do not use the supply unit in or near
wall sockets that contain an electric
air freshener to prevent irreparable
damage to the supply unit.
Electromagnetic elds (EMF)
-This Philips appliance complies
with all applicable standards and
regulations regarding exposure to
electromagnetic elds.
General
-This shaver can be safely cleaned
under the tap (Fig. 3).
-The appliance is suitable for mains
voltages ranging from 100 to 240 volts.
-The supply unit transforms
100-240 volts to a safe low voltage
of less than 24 volts.
Charging
Charge the appliance before rst use
and when the appliance start working
more slowly.
Charging takes approx. 10 hours.
A fully charged shaver provides up to
20 minutes of shaving time.
Charging with the supply unit
1 Put the small plug in the shaver.
2 Put the supply unit in the wall
socket (Fig. 4).
-The charging light on the supply
unit lights up continuously when
connected to wall socket.
-The light on the supply unit does
not change color and does not
go out when the appliance is
fully charged.
3 After charging, remove the supply
unit from the wall socket and pull
the small plug out of the appliance.
Using the appliance
Removing or attaching the
click-on attachments
1 Make sure the appliance is
switched o.
2 Insert the lug of the attachment into
the slot in the top of the appliance.
Then press down the attachment
to attach it to the appliance (‘click’)
(Fig. 5).
3 Pull the attachment straight o the
appliance (Fig. 6).
Note: Do not twist the attachment
while you pull it o the appliance.
Switching the appliance on
and o
1 To switch on the appliance, slide
the on/o button up (Fig. 7).
2 To switch o the appliance, slide
the on/o button down (Fig. 8).
Shaving
Skin adaptation period
Your rst shaves may not bring you the
result you expect and your skin may
even become slightly irritated. This is
normal. Your skin and beard need time
to adapt to any new shaving system.
To allow your skin to adapt to this new
appliance, we advise you to shave
regularly (at least 3 times a week) and
exclusively with this appliance for a
period of 3 weeks.
Dry shaving
1 Switch on the appliance.
2
Move the shaving heads over your
skin in circular movements to catch
all hairs growing in dierent directions
(Fig. 9). Exert gentle pressure for a
close, comfortable shave.
Note: Do not press too hard, as this
can cause skin irritation.
3 Clean the appliance after use
(see ‚Cleaning and maintenance‘).
Cleaning and maintenance
Cleaning the shaver under
the tap
Clean the shaver after every shave for
optimal performance (see ‚Cleaning
and maintenance‘). Always unplug and
switch o the shaver before you clean it.
Never use compressed air, scouring
pads, abrasive cleaning agents or
aggressive liquids such as petrol or
acetone to clean the appliance.
Be careful with hot water. Always
check if the water is not too hot, to
prevent burning your hands.
Never dry the shaving unit with a
towel or tissue, as this may damage
the shaving heads.
1 Rinse the shaving unit under a
warm tap.
Note: You can also clean the
shaving unit with the cleaning brush
supplied.
2
Turn the shaver up side down and
rinse the openings in the bottom of the
shaving head holders. Switch on the
shaver briey during rinsing (Fig. 10).
3 Open both shaving head holders
(Fig. 11).
4 Rinse the hair chambers and
shaving head holders under the tap
(Fig. 12).
5 Carefully shake o excess water
and let air dry completely.
6 Close the shaving head holders
(Fig. 13).
Thorough cleaning
The shaving unit consists of two shaving
heads. Clean one shaving head at a
time by following the steps below.
1 Open the shaving head holder
(Fig. 11).
2 To unlock the retaining frame,
gently squeeze both sides of the
retaining frame and ip open the
frame (Fig. 14).
3 Remove the shaving head. Each
shaving head consists of a cutter
and a guard (Fig. 15).
Note: Do not clean more than one
cutter and guard at a time, since
they are all matching sets. If you
accidentally mix up the cutters
and guards, it may take several
weeks before optimal shaving
performance is restored.
4 Remove the cutter from the shaving
guard (Fig. 16).
5 Rinse both parts with water.
6 After cleaning, place the cutter back
into the guard with the cutter legs
pointing downwards (Fig. 17).
7 Put the shaving head back into the
shaving head holder (Fig. 18).
Note: Make sure that the shaving
heads with the projections t
exactly onto the hooks of the
shaving head holder when placing
them (Fig. 20). The shaving heads
supplied with this appliance either
have notches or projections. Both
shaving systems are the same.
8 Push the retaining frame back onto
the shaving head holder until you
hear a click (Fig. 19).
9
Close the shaving head holder (Fig. 13).
Replacement
Replacing the shaving heads
For maximum shaving performance,
we advise you to replace the shaving
heads every two years. Replace
damaged shaving heads immediately.
Always replace the shaving heads with
original Philips shaving heads (see
‚Ordering accessories‘).
1 Switch o the appliance.
2 Open the shaving unit by opening
both shaving head holders (Fig. 11).
3 To unlock the retaining frames,
gently squeeze both sides of the
retaining frames and ip open the
shaving heads (Fig. 14).
4 Remove the shaving heads from
the shaving head holders (Fig. 15).
Throw away the used shaving
heads immediately to avoid mixing
them with the new shaving heads.
5 Place the new shaving heads in the
shaving head holders.
Note: Make sure that the shaving
heads with the projections t
exactly onto the hooks of the
shaving head holder when placing
them (Fig. 20). The shaving heads
supplied with this appliance either
have notches or projections. Both
shaving systems are the same.
6 Push the retaining frames back onto
the shaving head holder until you
hear a click (Fig. 19).
7 Close the shaving head holders
(Fig. 13).
Storage
Always slide the protection cap onto
the shaving unit to protect the shaving
unit from dirt or damage during
traveling or storage (Fig. 21).
We advise you to let the appliance dry
before you store it.
Ordering accessories
To buy accessories or spare parts,
visit www.shop.philips.com/service
or go to your Philips dealer. You can
also contact the Philips Consumer
Care Center in your country (see
the international warranty leaet for
contact details).
Available parts
The following accessories and spare
parts are available:
-SH30 Philips shaving heads
-HQ110 Cleaning spray
-A00390 supply unit
Note: Availability of the accessories
may dier by country.
Recycling
-Do not throw away the product
with the normal household waste
at the end of its life, but hand it in
at an ocial collection point for
recycling. By doing this, you help to
preserve the environment.
-This product contains a built-in
rechargeable battery which shall
not be disposed of with normal
household waste. We strongly
advise you to take your product
to an ocial collection point
or a Philips service centre to
have a professional remove the
rechargeable battery.
-Follow your country’s rules for the
separate collection of electrical
and electronic products and
rechargeable batteries. Correct
disposal helps prevent negative
consequences for the environment
and human health.
Removing the rechargeable
battery
Only remove the rechargeable
battery when you discard the shaver.
Before you remove the battery, make
sure that the shaver is disconnected
from the mains and that the battery is
completely empty.
Take any necessary safety
precautions when you handle tools
to open the shaver.
Be careful, the battery strips are sharp.
1 Disconnect the appliance from the
wall socket and let the appliance
run until the motor stops.
2 Insert a screwdriver under the
edge of the upper front panel and
remove it (Fig. 22).
3 Undo the screws in the top part of
the shaver (Fig. 23).
4 Remove the cover in the top of the
handle (Fig. 24).
5 Insert a screwdriver under the edge
of the front panel to remove the
panel and on/o button (Fig. 25).
6 Remove the small inner part below
the on/o button (Fig. 26).
7 Push the inner frame out of the
housing with the screwdriver (Fig. 27).
8 Cut the wires with pliers and
remove the battery (Fig. 28).
Troubleshooting
This chapter summarizes the most
common problems you could
encounter with the appliance. If you
are unable to solve the problem with
the information below, visit
www.philips.com/support for a list of
frequently asked questions or contact
the Consumer Care Center in your
country.
Prob-
lem
Possible
cause
Solution
The
shaver
does not
work as
well as it
used to.
The
shaving
heads are
damaged
or worn.
Replace the
shaving heads
(see 'Replace-
ment').
The
shaving
heads are
dirty.
Clean the
shaving
heads (see
'Cleaning and
maintenance').
Long
hairs
obstruct
the
shaving
heads.
Clean the
shaving
heads (see
'Cleaning and
maintenance').
The
recharge-
able
battery is
low.
Switch o the
shaver and
recharge the
battery (see
'Charging').
The
shaver
does
not work
when I
switch it
on.
The
recharge-
able
battery is
empty.
Switch o the
shaver and
recharge the
battery (see
'Charging').
The
shaving
heads
do not
stay in
place
in the
shaving
unit.
You
did not
x the
retaining
frames
properly.
The retaining
frames are
xed properly if
you hear a click
when you push
it back onto the
shaving heads.
Prob-
lem
Possible
cause
Solution
The
shaving
heads
with pro-
jec tions
are not
placed
properly.
Make sure that
the shaving
heads with the
projections t
exactly onto
the hooks of
the shaving
head holder
when placing
them (Fig. 20).
简体中文
感谢您的惠顾，欢迎光临飞利
浦！为了让您能充分享受飞利
浦提供的支持，请在
www.philips.com/welcome
上注册您的产品。
基本说明（图 1）
1 保护盖
2 剃须刀头支架
3 剃须刀头部件连接器
4 手柄
5 开/关指示
6 开/关按钮
7 小插头插座
8 刀片
9 网罩
10固定架
11电源部件
12充电指示灯
13小插头
未显示：清洁刷
重要安全信息
使用本产品及其附件之前，
请仔细阅读本重要信息，并妥
善保管以供日后参考。随附的
附件可能因产品而异。
危险
-保持电源部件干燥(图2)。
-警告符号注释：禁止在打开
的水龙头下进行清洗(图2)。
警告
-要给电池充电，请仅使用
产品随附的可拆卸电源部件
(A00390)。
-电源部件中包含一个变压器。
请勿自行更换电源部件的插
头，否则将导致严重后果。
-本产品也可以由8岁或以上
年龄的儿童以及肢体不健全、
感觉或精神上有障碍或缺乏相
关经验和知识的人士使用，但
前提是有人对他们使用本产品
进行监督或指导，以确保他们
安全使用，并且让他们明白相
关的危害。切勿让儿童玩弄
本产品。不要让儿童在无人
监督的情况下对本产品进行清
洁和保养。
-将剃须刀手持部分与电源软
线分开后，才能在水龙头下
清洗手持部分。
-使用前，请务必检查产品。
请勿使用损坏的产品，否则可
能对人体造成伤害。请务必
用原装型号更换损坏的部件。
-切勿拆开本产品更换充电
电池。
警告
-切勿将剃须刀浸入水中。
切勿在洗澡或淋浴时使用剃
须刀。
-切勿使用温度高于60°C的
热水冲洗剃须刀。
-只能将本产品用于用户手册
中所示的原定用途。
-出于卫生的目的，本产品只
能供一个人使用。
-切勿使用压缩气体、钢丝
绒、研磨性清洁剂或腐蚀性
液体（例如汽油或丙酮）来
清洁产品。
-冲洗剃须刀时，水可能从产
品底部漏出。这是正常现
象，而且没有危险，因为所
有电子元件都封闭在剃须刀
内部的密封电源部件中。
-请勿在包含电动空气清新器
的墙壁插座上或其周围使用
电源部件，以免电源部件受
到不可修复的损坏。
电磁场 (EMF)
-本Philips产品符合所有有关
暴露于电磁场的适用标准和
法规。
概述
-这款剃须刀可放心在水龙头
下(图3)清洗。
-符号注释：适合用在打开的
水龙头下进行清洗(图3)。
-本产品适合在100-240伏
的电源电压下工作。
-该电源部件可将100-240伏
的电压转换为24伏以下的安
全低电压。
充电
在首次使用剃须刀之前，以及
当剃须刀的刀头旋转速度变慢
时，请为剃须刀充电。
充电约需10小时。完全充电
的剃须刀可提供长达20分钟的
剃须时间。
使用电源部件充电
1 将小插头插入剃须刀。
2 将电源部件插入电源插座(图
4)。
-连接到电源插座时，电源
部件上的充电指示灯会持
续亮起。
-产品充满电后，电源部件
上的指示灯既不会改变颜
色，也不会熄灭。
3 充电之后，从电源插座上拔
下电源部件，并从产品上拔
下小插头。
4222_002_7315_1_DFU-Leaflet_55x99_v2.indd 2 12/05/17 12:00